Icemaker Accessory K it
Icemaker Accessory Kit
IM-4D
Safety Information . . . . . . . . . . . . . . . . 2
Operating Instructions . . . . . . . . . . . . 3
Before You Call For Service . . . . . . . . . . . 5, 6
Normal Sounds You May Hear . . . . . . . . . . . 3
Preparing for Vacation . . . . . . . . . . . . . . . . . 3
When You Should Set the
Icemaker Power Switch to OFF. . . . . . . . . . 3
Installation Instructions
Icemaker Installation . . . . . . . . . . . . . . . .7-13
Water Line Installation . . . . . . . . . . . . .18-21
Water Valve Assembly Installation . .14-17
Owner’s Manual and
Installation Instructions
Trousse
Machine à glaçons
Manuel d’utilisation
et d’installation
La section française commence à la page 23
Consumer Support
Consumer Support . . . . . . . . . . . Back Cover
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Equipo de Accesorios
Máquina de Hielos
Manual del propietario
e instalación
La sección en español empieza en la página 45
245D1524P001
49-60698-2
04-16 GE
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All
safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are
defined as:
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
State of California Proposition 65 Warnings:
WARNING This product contains one or more chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm.
SAFETY PRECAUTIONS
CAUTION
Do not place fingers or hands in the automatic icemaking
mechanism while the refrigerator is plugged in. This will
help protect you from possible injury.
It will also prevent interference with moving parts of the
ejector mechanism and the heating element that releases
the cubes, located on the bottom
of the icemaker.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
READ AND SAVE THESE INSTRUCTIONS
2
About the automatic icemaker.
GEAppliances.com
A newly-installed refrigerator may take 12 to 24 hours to begin making ice.
Icemaker
Power
Switch
Feeler Arm
(Appearance may vary)
Automatic Icemaker
The icemaker will produce seven cubes
SHUF\FOH³DSSUR[LPDWHO\²
cubes in a 24-hour period, depending on
freezer compartment temperature, room
temperature, number of door openings and
other use conditions.
If the refrigerator is operated before the
water connection is made to the icemaker,
set the power switch to OFF.
You will hear a buzzing sound each time the
icemaker fills with water.
Throw away the first few batches of ice to
allow the water line to clear.
Be sure nothing interferes with the sweep of
the feeler arm.
When the bin fills to the level of the feeler
arm, the icemaker will stop producing ice.
When the refrigerator has been connected to
the water supply, set the power switch to ON.
It is normal for several cubes to be joined
together.
The icemaker will fill with water when
it cools to freezing. A newly-installed
refrigerator may take 12 to 24 hours to
begin making ice cubes.
If ice is not used frequently, old ice cubes will
become cloudy, taste stale and shrink.
Preparing for Vacation
Set the icemaker power switch to OFF and
shut off the water supply to the refrigerator.
If the temperature can drop below freezing,
have a qualified servicer drain the water
supply system (on some models) to prevent
serious property damage due to flooding.
When you should set the icemaker power switch to OFF
■ When the ice storage bin is removed
for more than a minute or two.
■ When the refrigerator will not be used for
several days.
■ When the water supply will be shut off
for several hours.
Normal sounds you may hear
■ The icemaker water valve will buzz when
the icemaker fills with water. If the power
switch is in the ON position, it will buzz even
if it has not yet been hooked up to water.
Keeping the power switch in the ON position
before it is hooked up to water can damage
the icemaker. To prevent this, move the
power switch to the OFF position. This will
stop the buzzing.
■ The sound of cubes dropping into the bin
and water running in the pipes as the
icemaker refills.
3
Before you call for service…
Troubleshooting Tips
Save time and money! Review the following chart first
and you may not need to call for service.
Problem
Possible Causes
What To Do
Automatic icemaker
does not work
Freezer compartment
too warm.
• After installing the kit, allow the refrigerator to completely
cool down for 24 hours. Once the compartment is cool,
the icemaker will begin ice production.
Icemaker is not turned on.
• Move the icemaker
power switch to the
ON position.
Icemaker
Feeler
Arm
Power
Switch
Icemaker is not plugged
in correctly.
(Appearance may vary)
• Check that the icemaker
cord plug is fully inserted into
the socket. See Plug in
the icemaker.
Locking
Tabs
Hook
Water line kinked.
4
Clip Restraints
onto Locking
Tabs
• Check that the plastic water
line running from the valve
to the water tube inlet is not
kinked. See Connect the
water line. A kink in the
water line will restrict flow
to the water line.
Adhesive-backed
Fasteners for
Water Tube
Water supply turned off or
not connected.
• After installing the kit, make sure the house water supply
to the refrigerator has been turned on.
Piled up cubes in the storage bin
cause the icemaker to shut off.
• Level cubes by hand.
Water valve is not plugged in
correctly.
• Check that the valve wire
adapter is completely
plugged onto the terminals
on the water valve.
See Attach the water valve.
Valve Terminals
Adapter
GEAppliances.com
Problem
Possible Causes
What To Do
Leaking water around
the fill cup
Foam in the fill cup from
installing the fill tube.
• If the fill tube was installed by sliding it through the back
of the refrigerator, it may have picked up pieces of foam
as it was pushed through. This foam can interfere with
the water flow in the fill cup. Check the cup and make
sure there are no foam pieces.
Fill Tube
Fill tube not correctly seated
in the fill cup.
• Check that the fill tube is
correctly inserted in the
fill cup opening. See Mount
the icemaker.
Fill
Tube
Fill Cup
Leaking water behind
the refrigerator
House supply not properly
connected to the water valve.
• Check that the house supply is firmly attached to
the water valve. See Water line installation instructions.
Water line not connected
to the water tube inlet.
• Check that the plastic
water line running from
the valve to the water tube
inlet is firmly attached with
the hose clamp. See Connect
the water line.
Water
Tube Inlet
Hose Clamp
Water Line
Slow ice/freezer not
cold enough
Door left open.
• Check to see if package is holding door open.
Temperature control not
set cold enough.
• See About the Temperature Control in the Owner’s Manual of
the refrigerator.
Ice cubes too small/
slow ice
Water shutoff valve connecting
refrigerator to house water line
may be clogged.
• We recommend drilling a 1/4" hole
in the water pipe to connect the water
shut-off valve. Failure to drill a 1/4"
hole may result in reduced ice
production or smaller cubes.
See Installing the water line.
Water line kinked.
• Check that the plastic water
line running from the valve
to the water tube inlet is not
kinked. See Connect the
water line. A kink in the
water line will restrict flow
to the icemaker.
Drill 1/4" hole
in water pipe
Adhesive-backed
Fasteners for
Water Tube
5
Before you call for service…
Troubleshooting Tips
Save time and money! Review the following chart first
and you may not need to call for service.
Problem
Possible Causes
Ice cubes not landing
in bucket
Icemaker cord causing icemaker/ • Be sure icemaker power cord is in the hook as
bucket misalignment
stated in Step 8 in Installation Instructions.
Ice cubes have
odor/taste
Ice storage bin needs cleaning.
• Empty and wash bin. Discard old cubes.
Food transmitting odor/taste
to ice cubes.
• Wrap foods well.
Interior of refrigerator
needs cleaning.
• See Care and cleaning in the Owner’s Manual of the
refrigerator.
Normal operation.
• During normal operation, the water valve will “buzz”
when the icemaker fills with water.
Frequent “buzzing”
sound
6
What To Do
Installation
Instructions
IM-4D
Icemaker Kit
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or Visit our Website at: geappliances.ca
BEFORE YOU BEGIN
ARE YOU REPLACING AN
ICEMAKER WITH THIS KIT?
Read these instructions completely and carefully.
•
•
•
•
•
•
•
•
IMPORTANT – Save these instructions
for local inspector’s use.
It’s important that you use the water valve and fill tube
assembly that come with this kit, even though your
refrigerator may already have them installed.
codes and ordinances.
The old valve will not allow enough water through to fill
the icemaker properly and will cause damage.
IMPORTANT – Observe all governing
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
for future reference.
Skill level²,QVWDOODWLRQRIWKLVDSSOLDQFHUHTXLUHV
basic mechanical and electrical skills.
Completion time²²PLQXWHV
Proper installation is the responsibility of the
installer.
Product failure due to improper installation is not
covered under the Warranty.
DAMAGE – SHIPMENT/INSTALLATION
• If the unit is damaged in shipment, return the unit to the
store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than
the customer), repair or replacement must be made by
arrangement between customer and installer.
7
Installation Instructions
CONTENTS OF KIT IM-4D
6 Water Line Clamp
(strain relief), for house
water line
1 Icemaker
(Appearance may vary)
ICEMAKER
WARRANTY VERIFICATION
Date Installed
11 Short (~8”) Fill tube Assembly
12 Long (~9”) Fill tube Assembly
Dealer
n
llatio
Insta ctions
u
Instr
7
Warranty Label
2 Installation Instructions
13
Icemaker Fill Cup
(side-mounted)
8 Ice Bucket
14
3 Water Valve and
Tube Assembly
9
Hose Clamp
+H[+HDG6FUHZIRU
attaching water valve (3/8”)*
15 +H[+HDG6FUHZVIRU
attaching water tube
inlet cover (2) (5/8”)*
4 Adhesive-Backed Water Tube
Fasteners, to secure plastic
water tube (4)
10 Phillips Head Screws,
for mounting icemaker (2)
(7/8”)*
16 %UDFNHW([WHQVLRQ
5
+H[+HDG6FUHZ
for Water Line Clamp (3/4”)*
17 +H[+HDG6FUHZVIRU
EUDFNHWH[WHQVLRQ
(1/4”)*
*NOTE: Screw lengths are the lengths of the threaded portion of the screw, not including the head.
8
Installation Instructions
ICEMAKER INSTALLATION INSTRUCTIONS U V OR W
Are these the right instructions for your model? Follow the Installation Instructions indicated by the
ODEHORQWKHEDFNRIWKHUHIULJHUDWRU³89RU:)RUOHWWHU7JRWRSDJHIRULQVWUXFWLRQV
For letter V :
It is important to use the correct fill tube assembly
because the length is critical to the performance of
your icemaker. It is also critical to prevent any leaking
from the fill tube into the freezer itself.
• Open the fresh food door and locate the label in the
upper left corner of the compartment.
• Find the model number in bold listed under
MODEL NO.
• Match the two digit number in the model number
to the fill tube number in the table below. NOTE: The
desired number starts at the fourth character.
BEFORE YOU BEGIN
Read each step thoroughly before proceeding.
•
WARNING
To eliminate the
risk of electric shock or injury during
installation, you must first unplug the
refrigerator before proceeding. Failure
to follow these instructions can result in
electrical shock.
TOOLS YOU WILL NEED
Flat blade and Phillips
screwdrivers
Pliers
Sharp knife
1 SELECT FILL TUBE FOR YOUR
Model Number
REFRIGERATOR
GENERAL ELECTRIC COMPANY
APPLIANCE PARK LOUISVILLE, KY 40225
Which fill tube should you use?
There is a label on the back of the refrigerator that will
tell you which to use: U V or W
The fill tube you use will depend on the model and size
of your refrigerator.
MODEL NO. www.GEAppliances.com
GTH18GBDCRWW
SERIAL NO.
FZ743041
182A
LISTED HOSEHOLD REFRIGERATOR/FREEZER
IIIIIIIIIII
IIIIIIII
IIIIII
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
Model
Fill
Number Tube
12
# 12
15
# 11
16
# 11
18
# 12
21
# 12
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
For letter U :
Use long fill tube assembly #12 and cut off 1/2” of
length from the tip of the fill tube. This will ensure the
correct length fill tube for your model. This will provide
proper water flow into your fill cup and icemaker. It will
prevent the fill tube from freezing up with water and
ice.
For letter W :
Use short fill tube assembly #11 and cut off 1” of length
from the tip of the fill tube. This will ensure the correct
length fill tube for your model. This will provide proper
water flow into your fill cup and icemaker. It will prevent
the fill tube from freezing up with water and ice.
Cut 1/2”
Cut 1”
2 REPOSITION FREEZER SHELF
• Make sure the freezer shelf is in the lowest position.
9
Installation Instructions
ICEMAKER INSTALLATION INSTRUCTIONS (CONT.)
3 REMOVE THE OUTLET COVER
6 SET POWER SWITCH TO OFF
Peel off the outlet cover.
Set the icemaker power switch to OFF. Leave
the power switch in the OFF position until the
refrigerator is connected to the water supply
to prevent premature operation.
REMOVE ONLY
TO INSTALL
WATER FILL TUBE
Power
Switch
(Appearance may vary)
7 INSTALL THE ICEMAKER FILL CUP
4 INSTALL FILL TUBE
For letters U & V :
Install the icemaker fill cup (13) into the icemaker
as shown.
Go to the back of the refrigerator. On the refrigerator
side of the fill tube assembly (11 or 12 depending
on model), there is an adhesive backing. Remove the
adhesive backing and slide the tube into the hole near
the top at the back of the refrigerator. Firmly press on
the fill tube assembly to secure it to the refrigerator.
11
or
13
(Appearance
may vary)
12
For letter W :
Install the icemaker fill cup that came with your
refrigerator into the icemaker as shown. If the fill cup
KDVEHHQPLVSODFHGFDOODQGRUGHUSDUW
:5;,IWKHFRUUHFWILOOFXSLVQRWLQVWDOOHGLQWR
the icemaker, there is the possibility of water leaking
into the freezer and not into the icemaker.
5 PREPARE FOR INSTALLATION
Inside the freezer, loosen the two mounting screws
(B) but do not screw them all the way out. Your model
may have screws already installed; if not, remove the
2 plug buttons and insert the 2 Phillips head screws
7KHVFUHZVVKRXOGH[WHQGDSSUR[LPDWHO\
1/2" (13 mm) out from the freezer wall.
8 PLUG IN THE ICEMAKER
Holding the icemaker in
place, insert the icemaker
power cord plug into the
Hook
socket on the side wall,
making sure the prongs
and holes are matched.
Press the plug firmly into the
socket. Lock the plug in place
by clipping the restraints
onto each side of the plug.
Make sure the restraints click into place. Make sure
the power cord is still in the hook on the back of the
icemaker.
B
10
Installation Instructions
9 MOUNT THE ICEMAKER
11 ATTACH WARRANTY LABEL
• Lift the icemaker so the fill tube assembly (11 or 12
depending on model) fits in the fill cup opening (D).
Hang the icemaker on the two mounting screws (B).
Make sure:
• The power cord is still firmly in the socket.
• The fill tube assembly (11 or 12 depending on
PRGHOH[WHQGVLQWRWKHILOOFXSRSHQLQJDWWKHEDFN
of the icemaker. (Check the rear of the refrigerator
to make sure the fill tube has not been pushed out
of the back of the refrigerator).
• The icemaker mounting screws are located in the
uppermost position of the mounting slots on the
icemaker bracket.
• The icemaker is level.
• The icemaker power switch is in the OFF position.
SECURELY TIGHTEN THE ICEMAKER MOUNTING
SCREWS.
A label (7) is provided with this kit to record the date of
installation for warranty purposes. Apply it to the back
of the refrigerator.
12 KEEP THIS MANUAL
The warranty for the icemaker is printed in this
manual. Keep this manual with your Refrigerator
Owner’s Manual.
The icemaker installation inside the freezer is now
complete. Continue to the Water Valve Assembly
section on page 14.
11 12
B
D
10 INSTALL THE ICE BUCKET
Place the ice bucket (8) under the icemaker.
8
11
Installation Instructions
ICEMAKER INSTALLATION INSTRUCTIONS T
2 SET POWER SWITCH TO OFF
BEFORE YOU BEGIN
Set the icemaker power switch to OFF. Leave
the power switch in the OFF position until the
refrigerator is connected to the water supply to
prevent premature operation.
Read each step thoroughly before proceeding.
•
WARNING
To eliminate the
risk of electric shock or injury during
installation, you must first unplug the
refrigerator before proceeding. Failure
to follow these instructions can result in
electrical shock.
Power
Switch
TOOLS YOU WILL NEED
Flat blade and Phillips
screwdrivers
Pliers
(Appearance may vary)
Sharp knife
3 INSTALL THE MOUNTING SCREWS
• Skip to Step 4 if screws are already in place in
the freezer side wall.
• Install two self-tapping Phillips
head screwsIURPWKHNLW
in the holes in the side wall.
7KHVFUHZKHDGVVKRXOGH[WHQG
about 1/2" (13 mm) from the side
wall.
1 PREPARE FOR INSTALLATION
• Remove the storage
basket (on some models)
by pulling it out to the
stop position and lifting
it up and out.
Note: After removing
the basket, push the
H[WHQVLRQDUPVEDFN
into the freezer
compartment.
• Remove the chiller shelf
(on some models) by
pulling it straight out.
4 INSTALL THE ICEMAKER FILL CUP
Install the icemaker fill cup (end-mounted) that came
with your unit into the icemaker as shown. If the fill cup
KDVEHHQPLVSODFHGFDOODQGRUGHUSDUW
:5;
• Remove the center
vertical shelf support
(on some models) by
lifting it and rotating
its bottom to the right.
• Inside the freezer,
Remove side wall
remove the two small
plug buttons or leave
white plug buttons (on
screws in place
some models) from the
side wall. (If screws are
present instead of plugs,
leave them in place.)
Rear wall
plug button
• Remove and discard
the large white plug
from the rear freezer
wall.
• Remove the outlet cover with a flat-blade
screwdriver.
Outlet
cover
12
Installation Instructions
7 RE-INSTALL THE SHELF SUPPORT,
5 PLUG IN THE ICEMAKER
Holding the icemaker in place, insert the icemaker
power cord plug into the socket on the side wall,
making sure the prongs and holes are matched. Press
the plug firmly into the socket. Lock the plug in place
by clipping the restraints onto each side of the plug.
Make sure the restraints click into place and the power
cord is still in the hook on the back of the icemaker.
BUCKET, SHELF AND BASKET
Replace the center vertical shelf support, ice bucket,
chiller shelf and storage basket by reversing the steps
in Step 1.
8 ATTACH WARRANTY LABEL
A label (7) is provided with this kit to record the date
of installation for warranty purposes. Apply it to the
back of the refrigerator.
9 KEEP THIS MANUAL
The warranty for the icemaker is printed in this
manual. Keep this manual with your Refrigerator
Owner’s Manual.
The icemaker installation inside the freezer is now
complete. Continue to the Water Valve Assembly
section on page 16.
6 MOUNT THE ICEMAKER
• Lift the icemaker so the fill tube that was already
installed in the refrigerator fits in the fill cup
opening. Hang the icemaker on the two mounting
screws in the side wall.
Make sure:
• The power cord is still firmly in the socket.
• The fill tubeH[WHQGVLQWRWKHILOOFXSRSHQLQJRQ
the back of the icemaker. (Check the rear of the
refrigerator to make sure the fill tube has not been
pushed out of the back of the refrigerator).
• The icemaker mounting screws are located in
the uppermost position of the mounting slots on
the icemaker bracket.
• The icemaker is level.
• The icemaker power switch is set to OFF.
THEN SECURELY TIGHTEN THE ICEMAKER
MOUNTING SCREWS.
13
Installation Instructions
WATER VALVE ASSEMBLY INSTALLATION INSTRUCTIONS U V OR W
Are these the right instructions for your model? Follow the Installation Instructions indicated by the
ODEHORQWKHEDFNRIWKHUHIULJHUDWRU³89RU:)RUOHWWHU7JRWRSDJHIRULQVWUXFWLRQV
2 ATTACH THE WATER VALVE
BEFORE YOU BEGIN
•
Read each step thoroughly before proceeding.
•
WARNING
To eliminate the
risk of electric shock or injury during
installation, you must first unplug the
refrigerator before proceeding. Failure
to follow these instructions can result in
electrical shock.
Pliers
3
C
TOOLS YOU WILL NEED
Flat blade and Phillips
screwdrivers
Locate the female connector plug. Plug the
female connector (C) onto the male terminals
on the water valve (3). Either wire can go on
either terminal.
• Fasten the water valve to the cabinet by driving
the hex-head screw (9) from the kit into the hole
in the cabinet leg.
Sharp knife
9
1/4"and 5/16" Nutdrivers
1 REMOVE THE COVER
Remove the compressor compartment access cover.
This requires removing screws which attach the cover
to the back of the refrigerator case.
Be sure to save the screws as the access cover must
be reinstalled later to ensure your refrigerator will
function properly.
3 CONNECT WATER TUBE TO INLET
• Squeeze the ends of the hose clamp (14) from
the kit with pliers and slide the clamp over the fill
tube assembly, located in the top right corner of the
refrigerator.
• While still squeezing the clamp, insert the free end
of the water tube (3) into the fill tube assembly as far
as it will go.
• Then slide the clamp downward to capture the water
tube in place.
• Using one of the adhesive-backed fasteners (4),
secure the water tube to the back of the refrigerator
about 1/2" below the inlet.
• If the water tube is not pushed in as far as it can go
and the hose clamp is not in place over the fill tube
assembly, then leaks are possible.
Fill tube
assembly
Clamp
14
4
Water tube
14
3
Installation Instructions
6 WATER VALVE INSTALLED
4 INSTALL WATER LINE CLAMP
• Attach the metal water line clamp (strain relief) (6)
to the refrigerator. Drive the screw (5) from the kit
through the clamp (6) at the small indent into the
back of the cabinet.
• The metal clamp is for the house water line (see the
Water Line Installation Instructions). It is not to be
used for the water tube from the water valve up to
the inlet.
Refer to the Water Line Installation Instructions for
connection to the home water supply. After water
line installation is completed, set the icemaker
power switch to ON.
The icemaking cycle will not begin until the
icemaker and freezer compartment reach
operating temperature, then icemaking will begin
automatically.
5
7 REINSTALL THE COVER
6
Reinstall the compressor compartment access
cover. This requires using the screws you removed
previously to reattach the cover to the back of the
refrigerator case. This must be reinstalled for your
refrigerator to function properly.
Small indent for water
line clamp installation
5 ROUTE AND ATTACH
THE WATER TUBE
• Fasten the plastic water tube to the back
of the refrigerator with adhesive-backed
fasteners (4), spacing the fasteners as shown
to take up slack in the tube.
Adhesive-backed
fasteners for water tube
15
Installation Instructions
WATER VALVE ASSEMBLY INSTALLATION INSTRUCTIONS T
BEFORE YOU BEGIN
2 PLASTIC WATER TUBING
• Remove water line from the valve assembly (3)
included in this kit by removing the tube from the
clip and pushing on the bottom of the valve quickconnect, disengaging the tube and pulling it from
the valve.
Read each step thoroughly before proceeding.
•
WARNING
To eliminate the
risk of electric shock or injury during
installation, you must first unplug the
refrigerator before proceeding. Failure
to follow these instructions can result
in electrical shock.
Clip
TOOLS YOU WILL NEED
Quick-connect
Water line
Flat blade and Phillips
screwdrivers
Pliers
Sharp knife
Push up
Pull down
• Use the water line from the fill tube assembly
that came with the refigerator. The water line is
attached to the fill tube assembly that is already
installed in the refrigerator. Remove the plug from
the end of the waterline. Route the water line
through the clip on the valve pushing it into the
quick-connect on the valve. The white line will be
barely visible if properly engaged.
1/4"and 5/16" Nutdrivers
1 REMOVE THE COVER
Use a 5/16" nutdriver or an adjustable wrench to
remove the compressor compartment access cover.
7KLVUHTXLUHVUHPRYLQJVL[VFUHZVZKLFKDWWDFKWKH
cover to the back of the refrigerator case.
Be sure to save the screws as the access cover
must be reinstalled later to ensure your refrigerator
will function properly.
Clip
Quick-connect
Water line
3 ATTACH THE BRACKET EXTENSION
TO THE WATER VALVE
‡ 8
VHDµQXWGULYHUWRDWWDFKWKHEUDFNHWH[WHQVLRQ
(16) to the water valve bracket with the screw (17).
16
%UDFNHWH[WHQVLRQ
17
16
Installation Instructions
4 ATTACH THE WATER VALVE TO THE
6 ROUTE AND ATTACH THE PLASTIC
• Locate the female connector plug. Plug the female
connector onto the male terminals on the water
valve. Either wire can go on either terminal.
• Fasten the plastic water line to the back of the
MACHINE COMPARTMENT
WATER LINE
cabinet with adhesive-backed fasteners (4).
4
Adhesive-backed fastener
for plastic water line
7 WATER VALVE INSTALLED
• Fasten the water valve to the cabinet by driving the
hex-head screw (9) from the kit through the hole
LQWKHEUDFNHWH[WHQVLRQDQGLQWRWKHKROHLQWKH
cabinet.
Refer to the Water Line Installation Instructions for
connection to the home water supply. After water line
installation is completed, set the icemaker
power switch to ON.
The icemaking cycle will not begin until the
icemaker and freezer compartment reach
operating temperature, then icemaking will
begin automatically.
9
8 REINSTALL THE COVER
Reinstall the compressor compartment access
cover. This requires using the screws you removed
previously to reattach the cover to the back of the
refrigerator case. This must be reinstalled for your
refrigerator to function properly.
5 INSTALL WATER LINE CLAMP
• Attach the water line clamp (6) (strain relief) from the
kit to the refrigerator. With the clamp directly in line
with the water valve, drive the screw (5) from the kit
through the clamp at the indent into the back of the
cabinet.
5
6
• The metal clamp is for the house water line (see
Water Line Installation Instructions). It is not to be
used for the tubing from the water valve up to the
icemaker.
17
Installation Instructions
INSTALLING THE WATER LINE
BEFORE YOU BEGIN
WHAT YOU WILL NEED
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of
tubing you need. Approved plastic water supply
lines are SmartConnect™ Refrigerator Tubing
:;;:;;:;;DQG
:;;
When connecting your refrigerator to a GE Appliances
Reverse Osmosis Water System, the only approved
installation is with a GE Appliances RVKit. For
other reverse osmosis water systems, follow the
manufacturer’s recommendations.
If the water supply to the refrigerator is from a Reverse
Osmosis Water Filtration System AND the refrigerator
also has a water filter, use the refrigerator’s filter bypass
plug. Using the refrigerator’s water filtration cartridge
in conjunction with the RO filter can result in hollow ice
cubes and slower water flow from the water dispenser.
• Copper or SmartConnect™ Refrigerator Tubing kit,
1/4" outer diameter to connect the refrigerator to
the water supply. If using copper, be sure both ends
of the tubing are cut square.
To determine how much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add 8 feet
P%HVXUHWKHUHLVVXIILFLHQWH[WUDWXELQJDERXW
IHHW>[email protected]>[email protected]
diameter) to allow the refrigerator to move out from
the wall after installation.
SmartConnect™ Refrigerator Tubing Kits are available
in the following lengths:
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
LQVWUXFWLRQVFDUHIXOO\WRPLQLPL]HWKHULVNRIH[SHQVLYH
water damage.
2'P ²:;;
8'P
²:;;
15'(4.6P
²:;;
P
²:;;
Be sure that the kit you select allows at least 8 feet
(2.4 m) as described above.
NOTE: The only GE Appliances approved plastic
tubing is that supplied in SmartConnect™
Refrigerator Tubing kits. Do not use any other
plastic water supply line because the line is under
pressure at all times. Certain types of plastic will
crack or rupture with age and cause water damage
to your home.
• A GE Appliances water supply kit (containing
tubing, shutoff valve and fittings listed below) is
DYDLODEOHDWH[WUDFRVWIURP\RXUGHDOHURUIURP
Parts and Accessories, 877.959.8688.
• A cold water supply. The water pressure must be
EHWZHHQDQGSVL²EDURQPRGHOV
ZLWKRXWDZDWHUILOWHUDQGEHWZHHQDQGSVL
²EDURQPRGHOVZLWKDZDWHUILOWHU
Water hammer (water banging in the pipes) in
house plumbing can cause damage to refrigerator
parts and lead to water leakage or flooding. Call a
qualified plumber to correct water hammer before
installing the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting
the water line, make sure the icemaker power switch
is in the OFF position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.
All installations must be in accordance with local
plumbing code requirements.
WARNING
supply only.
Connect to potable water
• Power drill.
• 1/2" or adjustable wrench.
• Straight and Phillips blade screwdriver.
18
Installation Instructions
2 CHOOSE THE VALVE LOCATION
WHAT YOU WILL NEED (CONT.)
Choose a location for the valve that is easily
accessible. It is best to connect into the side
of a vertical water pipe. When it is necessary
to connect into a horizontal water pipe, make
the connection to the top or side, rather than at
the bottom, to avoid drawing off any sediment
from the water pipe.
• Two 1/4" outer diameter compression nuts and
2 ferrules (sleeves)³WRFRQQHFWWKHFRSSHUWXELQJ
to the shutoff valve and the refrigerator water valve.
OR
• If you are using a SmartConnect™ Refrigerator
Tubing kit, the necessary fittings are preassembled
to the tubing.
3 DRILL THE HOLE FOR THE VALVE
Drill a 1/4" hole in the water pipe (even if using
a self-piercing valve) using a sharp bit. Remove
any burrs resulting from drilling the hole in the
pipe. Take care not to allow water to drain into
the drill. Failure to drill a 1/4" hole may result
in reduced ice production or smaller cubes.
‡,I\RXUH[LVWLQJFRSSHUZDWHUOLQHKDVDIODUHGILWWLQJ
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refrigerator OR you can cut off the flared fitting
with a tube cutter and then use a compression
fitting. Do not cut formed end from SmartConnect™
Refrigerator tubing.
• Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32" at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
4 FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe with
the pipe clamp.
Install the shutoff valve on the nearest frequently used
drinking water line.
Pipe Clamp
1 SHUT OFF THE MAIN WATER SUPPLY
Turn on the nearest faucet long enough to clear
the line of water.
Saddle-Type
Shutoff Valve
Vertical Cold
Water Pipe
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
19
Installation Instructions
INSTALLING THE WATER LINE (CONT.)
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
5 TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE: Do not overtighten or you may crush
the tubing.
Washer
Pipe Clamp
8 FLUSH OUT THE TUBING
Inlet End
Turn the main water supply on and flush out
the tubing until the water is clear.
Clamp
Screw
Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.
6 ROUTE THE TUBING
Route the tubing between the cold water line and
the refrigerator.
Route the tubing through a hole drilled in the wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
9 CONNECT THE TUBING
NOTE: %HVXUHWKHUHLVVXIILFLHQWH[WUDWXELQJ
(about 8 feet [244 cm] coiled into 3 turns of about
>[email protected]
to move out from the wall after installation.
TO THE REFRIGERATOR
NOTES:
• Before making the connection to the refrigerator,
be sure the refrigerator power cord is not plugged
into the wall outlet.
• If your refrigerator does not have a water
filter, we recommend installing one if your water
supply has sand or particles that could clog the
screen of the refrigerator’s water valve. Install it
in the water line near the refrigerator. If using
SmartConnect™ Refrigerator Tubing kit, you
ZLOOQHHGDQDGGLWLRQDOWXEH:;;WR
connect the filter. Do not cut plastic tube to
install filter.
5HPRYHWKHSODVWLFIOH[LEOHFDSIURPWKHZDWHUYDOYH
(refrigerator connection).
7 CONNECT THE TUBING TO
THE VALVE
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutoff valve.
Make sure the tubing is fully inserted into the valve.
Tighten the compression nut securely.
For plastic tubing from a SmartConnect™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then tighten
one additional turn with a wrench. Overtightening
may cause leaks.
Saddle-Type
Shutoff Valve
Compression
Nut
SmartConnect™
Tubing
Packing Nut
Outlet Valve
Ferrule (sleeve)
20
Installation Instructions
11 INSTALLING THE REFRIGERATOR
9 CONNECT THE TUBING
TO THE REFRIGERATOR (CONT.)
Plug in the refrigerator.
Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown. On
SmartConnect™ Refrigerator Tubing kit, the nuts
are already assembled to the tubing.
Insert the end of the tubing into the water valve
connection as far as possible. While holding the
tubing, tighten the fitting.
Arrange the coil of tubing
so that it does not vibrate
against the back of the
refrigerator or against the
wall. Push the refrigerator
back to the wall.
For plastic tubing from a SmartConnect Refrigerator
Tubing kit, insert the molded end of the tubing into
the refrigerator connection and tighten compression
nut until it is hand tight, then tighten one additional
turn with a wrench. Overtightening may cause leaks.
Fasten the tubing into the clamp provided to hold
it in a vertical position. You may need to pry open
the clamp.
Tubing
Clamp
12 START THE ICEMAKER
1/4" Tubing
Set the icemaker power switch to the ON position.
The icemaker will not begin to operate until it
UHDFKHVLWVRSHUDWLQJWHPSHUDWXUHRIƒ)²ƒ&
or below. It will then begin operation automatically
if the icemaker power switch is in the ON position.
1/4"
Compression
Nut
Ferrule
(sleeve)
Refrigerator
Connection
SmartConnect™
Tubing
10 TURN THE WATER ON
AT THE SHUTOFF VALVE
Tighten any connections that leak.
Reattach the compressor compartment access
cover.
21
Icemaker Warranty.
All warranty service provided by our Factory Service Centers, or an
authorized Customer Care® technician. To schedule service, on-line,
visit us at GEAppliances.com, or call 800.GE.CARES (800.432.2737). In
Canada, call 1.800.561.3344. Please have serial number and model
number available when calling for service.
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
For The Period Of:
We Will Replace:
One Year
From the date of the
original purchase
Any part of the icemaker which fails due to a defect in materials or workmanship.
During this limited one-year warranty, GE Appliances will provide, free of charge, replacement parts
for any defective part in your icemaker kit.
What Is Not Covered (for customers in the United States):
■ Service trips to your home to teach you how to use
the product.
■ Replacement of house fuses or resetting of circuit
breakers.
■ Improper installation.
You are responsible for providing adequate electrical,
plumbing, and other connecting facilities, including the
water line to the icemaker and the water line installation.
■ Damage to the product caused by accident, fire, floods
or acts of God.
■ Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
■ Incidental or consequential damage caused by possible
defects with this appliance.
■ Product not accessible to provide required service.
(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQ
this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or
fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer
is not available, you may be responsible for a trip charge or you may be required to bring the product to an
Authorized GE Appliances Service location for service. In Alaska, the warranty excludes the cost of shipping or
service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
What Is Not Covered (for customers in Canada):
■ Service trips to your home to teach you how to use
the product.
Read your Owner’s Manual. If you then have any questions
about operating the product, please contact your dealer or
our Consumer Relations office at:
Manager, Consumer Relations
Mabe Canada Inc.
)DFWRU\/DQH6XLWH
Moncton, N.B.
E1C 9M3
■ Improper installation.
If you have an installation problem, contact your dealer
or installer. You are responsible for providing adequate
HOHFWULFDOH[KDXVWLQJDQGRWKHUFRQQHFWLQJIDFLOLWLHV
■ Replacement of house fuses or resetting of circuit
breakers.
■ Failure of the product if it is misused, or used for other
than the intended purpose or used commercially.
■ Damage to product caused by accident, fire, floods or
acts of God.
WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES.
Warrantor: MABE CANADA INC.
22
Consumer Support.
GE Appliances Website
In the U.S.: GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts or even schedule service on-line. In Canada: www.geappliances.ca
Schedule Service
In the U.S.: GEAppliances.com
Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at
your convenience any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.
In Canada, call 1.800.561.3344
Real Life Design Studio
In the U.S.: GEAppliances.com
*($SSOLDQFHVVXSSRUWVWKH8QLYHUVDO'HVLJQFRQFHSW³SURGXFWVVHUYLFHVDQGHQYLURQPHQWVWKDWFDQEHXVHGE\
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and mental
abilities and impairments. For details of GE Appliances Universal Design applications, including kitchen design
ideas for people with disabilities, check out our Website today. For the hearing impaired, please call 800.TDD.GEAC
(800.833.4322).
In Canada, contact: Manager, Consumer Relations, Mabe Canada Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9M3
Extended Warranties
In the U.S.: GEAppliances.com
Purchase a GE Appliances extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours. GE Appliances
Consumer Home Services will still be there after your warranty expires. In Canada, call 1.800.290.9029
Parts and Accessories
In the U.S.: GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at
877.959.8688 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
VKRXOGEHUHIHUUHGWRTXDOLILHGVHUYLFHSHUVRQQHO&DXWLRQPXVWEHH[HUFLVHGVLQFHLPSURSHUVHUYLFLQJPD\FDXVH
unsafe operation.
Customers in Canada should consult the yellow pages for the nearest Mabe service center, or call 1.800.661.1616.
Contact Us
In the U.S.: GEAppliances.com
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the details
including your phone number, or write to:
General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
In Canada: www.geappliances.ca, or write to: Director, Consumer Relations, Mabe Canada Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9M3
Register Your Appliance
In the U.S.: GEAppliances.com
5HJLVWHU\RXUQHZDSSOLDQFHRQOLQH³DW\RXUFRQYHQLHQFH Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also
mail in the pre-printed registration card included in the packing material, or detach and use the form in this
Owner’s Manual. In Canada: www.geappliances.ca
Printed in the United States
Universal Keywords: Div46 Src363 GE General Electric Mechtech
Document Specific Keywords: Instruction Sheet
Date: 102816
Document Name: IM4D
Subject: GE Refrigerator Icemaker Accessory Kit Instruction Sheet
Models: GBE21DSKARSS GBE21DGKARWW GBE21DGKARBB ABE21DGKARBS
ABE21DGKARWS WR29X26688 WR29X10074 WR29X10092 ABE21DGKARBS
ABE21DGKARWS ABE21DGKBS GBE21DGKARBB GBE21DGKARWW
GBE21DSKARSS GTH21GBEBB GTH21GBECC GTH21GCEABB
GTH21GCEAWW GTH21GCEBB GTH21GCEWW GTH21KCWABB
GTH21KCWAWW GTH21KCXABB GTH21KCXACC GTH21KCXAWW
GTH21SCWASS GTH21SCXASS GTL21KCWABS GTL21KCXABS
GTS21KCXABB GTS21KCXAWW GTS21SBXASS GTS21SCXASS
GTZ21GCEASS GTZ21GCEBSS ABE20EGEBRBS ABE20EGEBRWS
ABE20EGHBRBS ABE20EGHBRWS CFCP1NIZASS CFCP1NIZBSS
CFCP1NIZCSS CFCP1NIZDSS CFCP1NIZESS CNE22SSEAFSS
CNS23SSHAFSS CWS21SSEAFSS CWS21SSEBFSS GBE20ESEBRSS
GBE20ETEBRBB GBE20ETEBRCC GBE20ETEBRWW GBS20EGHBRBB
GBS20EGHBRWW GBS20ESHBRSS GBSC0HCXERBB GBSC0HCXERWW
GBSC0HCXFRBB GBSC0HCXFRWW GDSS0KCXFRSS GFCE1NFBADSS
GFCE1NFBEDSS GFCE1NFBFDSS GFSF2HCYHBB GFSF2HCYHWW
GFSF2KEYHBB GFSF2KEYHCC GFSF2KEYHWW GFSL2KEYHLS
GFSS2HCYHSS GFSS2HCYJSS GFSS2KEYHSS GNE22GGEAFBB
GNE22GGEAFWW GNE22GGEBFBB GNE22GGEBFWW GNE22GMEAFES
GNE22GMEBFES GNE22GMECFES GNE22GSEAFSS GNE22GSEBFSS
GNS22ESEAFSS GNS22ESEBFSS GNS23GGHBFBB GNS23GGHBFWW
GNS23GMHBFES GNS23GSHBFSS GTE16DTHBRCC PDCE1NBZCDSS
PDCE1NBZCJSS PDCE1NBZHDSS PDCE1NBZHJSS PDCS1NCZALSS
PDCS1NCZARSS PDCS1NCZBLSS PDCS1NCZBRSS PDCS1NCZCLSS
PDCS1NCZCRSS PDCS1NCZHLSS PDCS1NCZHRSS PDSE5NBZCDSS
PDSE5NBZHDSS PDSS0MFYELSS PDSS0MFYERSS PFCA1NJZADSS
PFCA1NJZBDSS PFCA1NJZCDSS PFCA1NJZHDSS PFCA1NJZIDSS
PFCE1NFZAANB PFCE1NFZBANB PFCE1NFZCANB PFCE1NJYCDSS
PFCE1NJZADSS PFCE1NJZBDSS PFCE1NJZCDSS PFCE1NJZHDSS
PFCF1NFCABB PFCF1NFCAWW PFCF1NFCBBB PFCF1NFCBWW
PFCF1NFZABB PFCF1NFZAWW PFCF1NFZBBB PFCF1NFZBWW
PFCF1NFZCBB PFCF1NFZCWW PFCF1PJZABB PFCF1PJZAWW
PFCF1PJZBBB PFCF1PJZBWW PFCF1PJZCBB PFCF1PJZCWW
PFCS1NFCASS PFCS1NFCBSS PFCS1NFZASS PFCS1NFZBSS
PFCS1NFZCSS PFCS1NFZHSS PFCS1PJZASS PFCS1PJZBSS
PFCS1PJZCSS PFCS1PJZDSS PFCS1PJZHSS PFCU1NJZCDSS
PFCU1NJZHDSS PFE22KSEAFSS PFIC1NFZABV PFIC1NFZAWV
PFIC1NFZBBV PFIC1NFZBWV PFIC1NFZCBV PFIC1NFZCWV PFIC1NFZDBV
PFIC1NFZDWV PFIE1NFZAAKB PFIE1NFZBAKB PFIE1NFZCAKB
PFQS5PJZASS PFQS5PJZCSS PFQS5PJZHSS PFS23KSHAFSS
PFSA5NJZADSS PFSA5NJZCDSS PFSA5NJZHDSS PFSA5NJZIDSS
PFSE5NJZADSS PFSE5NJZBDSS PFSE5NJZCDSS PFSE5NJZHDSS
PFSF0MFZEBB PFSF0MFZEWW PFSF0MFZFBB PFSF0MFZFWW
PFSF0MFZGBB PFSF0MFZGWW PFSF2MIYGBB PFSF2MIYGWW
PFSF2MIYHBB PFSF2MIYHWW PFSF2MJYHBB PFSF2MJYHWW
PFSF5NFCABB PFSF5NFCACC PFSF5NFCAWW PFSF5NFZABB
PFSF5NFZACC PFSF5NFZAWW PFSF5NFZBBB PFSF5NFZBCC
PFSF5NFZBWW PFSF5NFZCBB PFSF5NFZCCC PFSF5NFZCWW
PFSF5PJZABB PFSF5PJZAWW PFSS0MFZESS PFSS0MFZGSS
PFSS0MFZHSS PFSS2MIYGSS PFSS2MIYHSS PFSS2MIYISS
PFSS2MIYJSS PFSS2MJYDSS PFSS2MJYGSS PFSS2MJYHSS
PFSS2MJYISS PFSS2MJYJSS PFSS5NFCASS PFSS5NFZASS
PFSS5NFZBSS PFSS5NFZCSS PFSS5NFZHSS PFSS5PJZASS
PFSS5PJZCSS PGCS1NFZASS PGCS1NFZBSS PGCS1NFZCSS
PGCS1NFZHSS PGCS1PJZASS PGCS1PJZBSS PGCS1PJZCSS
PGCS1PJZHSS PGSS5NFZASS PGSS5NFZBSS PGSS5NFZCSS
PGSS5NFZHSS PGSS5PJZASS PGSS5PJZCSS PHE25TGXBFBB
PNS20KSEAFSS PNS20KSHAFSS ZFGB21HZASS ZFGB21HZBSS
ZFGB21HZCSS ZFGB21HZJSS ZFGP21HZASS ZFGP21HZBSS
ZFGP21HZCSS ZFGP21HZJSS
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement