Replacing a wall-mounted thermostat

Replacing a wall-mounted thermostat
1
Replacing a wall-mounted thermostat
You can watch this installation at:
http://netatmo.com/video1
Warning
Warning!
• Read these instructions carefully before starting the installation.
• The Netatmo Thermostat must be installed according to
applicable standards.
• Before any intervention, make sure power is turned off.
In the box
Relay
1
2
230V
Thermostat
(Mobile stand)*
Relay
(Boiler adapter)*
3
+
Mounting Plate
(Tape)*
Plug the mains adapter
into the Relay.
Trim plate
Color Adhesives
Mains adapter
3 AAA batteries
4 screws
4 screw anchors
1 USB cable
* not used in this setup
The Relay will blink white.
Plug the Relay into a wall
socket in the same room
as your existing thermostat.
4
Switch off the power supply.
Identify
Replace
1
Remove the cover of your old
thermostat.
1
Take a picture of the wiring.
Disconnect your old thermostat.
Remove it from the wall.
2
- If there are only two wires, they are the
control wires and are useful in this setup.
- If there are more than two wires, identify
the two control wires. They are usually
black or grey.
The wires can be identified as shown on
the following diagram
Note: If there are more than two wires, the
others are power supply wires and are useless
here. They are usually brown, blue, green or
yellow.
In doubt, please send a picture to
[email protected] and our support team
will help you identify the right wires
Control wires
Usually black
or grey wires
COM / NO
Power supply wires
Usually blue and
brown wires
3
Pass the wires through the Netatmo
mounting plate and screw the latter to the
wall.To hide potential scratches and holes
left behind, use the trim plate.
4
Screw the control wires previously identified
into the electrical terminals and insulate the
unused wires.
Place and screw the protection cover onto
the electrical terminals.
P/N
or
L/N
Customisation
Thermostat
1
You can choose to customize your
Thermostat by using one of the colour
adhesives.
1
Insert the batteries in the Thermostat.
2
Take off the outer frame of the adhesive.
2
Set the Thermostat on the mounting plate.
3
Stick it on the back of your Thermostat.
3
Switch the power supply back on.
Thermostat
Test
1
Push the top of the Thermostat until
it displays « MAX ».
The Thermostat will display the start screen
and search for the Relay.
The Thermostat switches
the boiler on.
clic
+
21
20
+
5
0
20
0
2
+
21
20
5
0
+
Desired temperature
Measured temperature
or
21
20
Push the bottom of the Thermostat
until it displays « OFF ».
5
0
The Thermostat switches the boiler
off.
+
+
20
20
0
0
clic
If the Thermostat has found the
Relay, it displays the desired
temperature and the room
temperature.
If the Thermostat hasn’t found the
Relay, it displays the «!» symbol.
In this case, move the relay closer to
the Thermostat and wait until the «!»
symbol disappears.
Note: If the Thermostat doesn’t switch on and off the boiler, the control wires have been incorrectly wired. In this
case, check your wiring using the picture of your old thermostat’s wiring to identify the right control wires.
If the boiler does the opposite of what is described (for example, it switches OFF when the Thermostat displays MAX),
it means that you will have to change the polarity of the Thermostat. You can modify the polarity in the advanced
settings of the app once you will have finished the setup.
App
Specifications
SIZE
Thermostat: 83 x 83 x 22 mm
To use your Thermostat from your smartphone,
tablet or computer, visit:
http://therm.netatmo.com
DESIGN
Designed by Starck.
Translucent minimalist plexiglass cube.
5 interchangeable colours in the box.
SENSORS AND MEASUREMENTS
Temperature (measurement):
Ranges from : 0°C à 50°C
Accuracy: -/+ 0,1°C
Temperature (setpoint):
Ranges from: 5°C à 30°C
Incrément: 0.5°C
Unit: °C
E-INK DISPLAY
Energy efficient, longer battery life and
optimal readability.
PC / Mac
Smartphone / Tablettes
FREE APP, LIFETIME SUPPORT
No subscription fee.
App available on the App Store,
Windows Phone Store and on
Google Play.
Free access to your online personal
dashboard.
Accessible from multiple devices.
WIRELESS SPECIFICATIONS
Wi-Fi 802.11 b/g/n compatible (2.4GHz).
Supported security: Open/WEP/WPA/
WPA2-personal (TKIP and AES).
Wireless connection between thermostat and relay:
radio long range 100 m.
POWER AND BATTERIES
3 AAA batteries.
2 years battery life.
SETUP AND COMPATIBILITY
Compatible with gas, fuel, wood boilers
and heat pumps.
Switching current: max 4 A
Switching voltage: max 250 VAC
Switching power: max 120 W
HOMEKIT
Controlling HomeKit-enabled accessories away
from home requires an Apple TV (3rd generation
or later) with Apple TV software 7.0 or later and an
iPhone, iPad, or iPod touch with iOS 8.1 or later.
EU Declaration of Conformity
We, Netatmo, declare that this device is
in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Safety warnings
This device must be installed according
to the applicable norms. Use only with
supplied power plug adaptor and boiler
adaptor. This device is for indoor use
only.
Before inserting the batteries, check that
the contacts in the device and on the
batteries are clean, is necessary clean
them.Exposure
NoteStatement
the polarity (+/-) when inFCC Radiation
This equipment complies with FCC RF radiation exposure limits set forth for an
serting the batteries. Do not throw
uncontrolled environment. This transmitter should be installed and operated
with athe
minimum
distance of 20 centimeters
and your
batteries
into abetween
fire,the radiator
short-cirbody and must not be co-located or operating in conjunction with any other
cuit
themThis or
dismantle
antenna
or transmitter.
equipment
complies with them.
Part 15 of theKeep
FCC Rules.
Operation is subject to the following two conditions:
away
from
batteries.
Seek
(1) Thischildren
device may not cause
harmful
interference,
and
(2) This device must accept any interference received, including interference
medical attention immediately if a
that may cause undesired operation.
battery is swallowed. Do not attempt to
repair the device yourself; customer
service is available. Any changes or
modifications to this unit not expressly
approved by the party responsible for
compliance could void the user’s authority
EU Declaration of Conformity
We, Netatmo, declare that this device is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
to operate the equipment. Thermostat and
relay insulation: class II devices. This
device is not intended for use by
persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure
Canadian Compliance Statement
Thisthat
devicethey
complies
withnot
Industry
Canada
RSS standard(s).
do
play
withlicense-exempt
the appliance.
Operation is subject to the following two conditions: (1) this device may not
Legal
notice
cause
interference,
and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Use of the HomeKit logo means that
Cet appareil est conforme aux normes CNR exemptes de licence d'Industrie
Canada.
fonctionnement est
soumis aux deuxhas
conditions
suivantes:
an Leelectronic
accessory
been
de-(1) cet
appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter
connect
specifically
iPod,
toutesigned
interférence,to
y compris
celles susceptibles
de provoquer to
un fonctionnement
non souhaité de l'appareil.
or iPad,
respectively,
and has
ThisiPhone,
Class B digital apparatus
complies
with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
been certified by the developer to meet
Canada.
ThisApple
device and
its antenna(s) muststandards.
not be co-locatedApple
or operating
performance
is in
conjunction with any other antenna or transmitter.
not responsible
operation
of this en
Cet appareil
et son antenne (s) nefor
doit the
pas être
co-localisés ou fonctionnant
conjonction avec une autre antenne ou transmetteur.
device or its compliance with safety and
Taiwan Wireless Statements
regulatory standards.
無線設備的警告聲明
本產品符合低功率電波輻射性電機管理辦法 第〸二條、第〸四條等
Please note that the use of this acces條文規定: sory
1. 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使
用�均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 with iPod, iPhone, or iPad may affect wi2. 低功率射頻電機之使用不得影�飛航安全及干擾合法通信;經發
現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 reless performance.
前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性
電機設備之干擾。
Complies with
IDA Standards
V16
Copyright Netatmo © 2015 All rights reserved. Reproduction and distribution prohibited without written authorization from Netatmo.
V5-EN
2
Replacing a wireless thermostat
You can watch this installation at:
http://netatmo.com/video2
or installing your first thermostat
You can watch this installation at:
http://netatmo.com/video3
In the box
Warning
Warning!
230V
• Read these instructions carefully before starting the installation.
• The Netatmo Thermostat must be installed according to
applicable standards.
• Before any intervention, make sure power is turned off.
Thermostat
Mobile stand
Relay
Boiler adapter
+
(Mounting Plate)*
Tape
(Trim plate)*
3 AAA batteries
Color Adhesives
(Mains adapter)*
4 screws
4 screw anchors
1 USB cable
* not used or optional in this setup
Wiring
Wiring
Connect the blue and brown
wires of the boiler adapter
cable to the power supply
terminals (P/N or L/N).
Open the boiler door (use the
boiler manual, if necessary).
Identify the thermostat terminals in
the boiler, often labeled LS-LR, TA or
COM-NO. They may be identifiable
thanks to a shunt between the two
thermostat terminals.
LS / L R
or
TA
or
COM / NO
If your are replacing a wireless thermostat, find your former thermostat’s
relay and remove it.
P/N
or
L/N
In doubt, please send a picture
of your wiring to:
[email protected]
and our support team will help
you identify the right terminals.
If you are installing your first thermostat, please remove the shunt between
the two thermostat terminals.
Connect the black and grey wires
of the boiler adapter cable to the
thermostat terminals.
Our forum can help you
identify where to plug the wires
in, at forum.netatmo.com.
Thermostat terminals
Black and grey wires
No polarity
Note : Some thermostats are connected to different terminals from those on the diagram’s list (for example, eBus,
EMS…). In this case, you will have to identify the right thermostat terminals to connect the Relay of the Netatmo
Thermostat.
230 V Power supply terminals
Blue and brown wires
Setting the Relay
The boiler adapter should be placed
as far as possible from metallic items
(wiring, pipes, electrical grid…).
Testing the Relay
1
30 cm
Connect the Relay into the boiler
adapter.
2
Switch the power supply back on.
3
The Relay will blink white.
The boiler adapter can be affixed to the wall with the double-sided tape
or the screws provided.
or
Note : If the Relay does not blink after turning the power back on, it is not power supplied.
Please check how the blue and brown wires are wired. Do not forget to switch off the power supply before
any intervention.
Testing the Relay
Thermostat
1
2
1
Push the Relay
button.
The Relay will light up white
and switch on the boiler.
Insert the batteries into
the Thermostat.
3
4
+
21
20
Push the Relay
button again.
The Relay light will turn off
to indicate the boiler is off.
Note: If the boiler doesn’t switch on when the white light is on, the Relay can be incorrectly wired to the boiler. In
this case, check where the grey and black wires are connected. Please note that some boilers can take up to 20
minutes to respond after pushing the Relay’s button.
In doubt, please read in your boiler’s instructions manual [ the «room thermostat» section].
5
0
2
The Thermostat will display the
start screen and search for
the Relay.
+
Desired temperature
Measured temperature
If the Thermostat has found the
Relay, it will display the setpoint and
the room temperatures.
or
21
20
5
0
If the Thermostat hasn’t found the
Relay, it will display the «!» symbol.
In this case, move the Relay closer to
the Thermostat and wait until the «!»
symbol disappears.
Location
Customization
1
2
You can choose to customize
your Thermostat by using one
of the colour adhesives.
Take off the outer frame of the adhesive.
or
Set the Thermostat on the mounting
plate.
Clip the Thermostat on its mobile
stand and place it on a shelf in the
living room.
1m
1m
+
18
22
3
5
1,5 m
Stick it on the back of your Thermostat.
More than 1 m from the
openings
A 1,5 m high
Away from any cold
or heat source
App
Test
1
Tap the top of the Thermostat until
the screen shows « MAX ».
The Thermostat will switch on the
boiler.
clic
+
21
20
+
5
0
20
0
To use your Thermostat from your smartphone,
tablet or computer, visit:
http://therm.netatmo.com
2
Tap the bottom of the Thermostat
until it displays « OFF ».
The Thermostat will switch off the
boiler.
+
+
20
20
0
0
clic
Note: If the boiler does the opposite of what is described (for example, it switches OFF when the Thermostat
displays MAX), it means that you will have to change the polarity of the Thermostat. You can modify the polarity in
the advanced settings of the app once you will have finished the setup.
PC / Mac
Smartphone / Tablettes
Specifications
SIZE
Thermostat: 83 x 83 x 22 mm
DESIGN
Designed by Starck.
Translucent minimalist plexiglass cube.
5 interchangeable colours in the box.
SENSORS AND MEASUREMENTS
Temperature (measurement):
Ranges from : 0°C to 50°C
Accuracy: ± 0,1°C
Temperature (setpoint):
Ranges from: 5°C to 30°C
Incrément: 0.5°C
Unit: °C
E-INK DISPLAY
Energy efficient, longer battery life and
optimal readability.
FREE APP, LIFETIME SUPPORT
No subscription fee.
App available on the App Store,
Windows Phone Store and on
Google Play.
Free access to your online personal
dashboard.
Accessible from multiple devices.
WIRELESS SPECIFICATIONS
Wi-Fi 802.11 b/g/n compatible (2.4GHz).
Supported security: Open/WEP/WPA/
WPA2-personal (TKIP and AES).
Wireless connection between thermostat and relay:
radio long range up to 100 m.
POWER AND BATTERIES
3 AAA batteries.
2 years battery life.
SETUP AND COMPATIBILITY
Compatible with gas, fuel, wood boilers
and heat pumps.
Switching current: max 4 A
Switching voltage: max 250 VAC
Switching power: max 120 W
HOMEKIT
Controlling HomeKit-enabled accessories away
from home requires an Apple TV (3rd generation
or later) with Apple TV software 7.0 or later and an
iPhone, iPad, or iPod touch with iOS 8.1 or later.
EU Declaration of Conformity
We, Netatmo, declare that this device is
in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Safety warnings
This device must be installed according
to the applicable norms. Use only with
supplied power plug adaptor and boiler
adaptor. This device is for indoor use
only.
Before inserting the batteries, check that
the contacts in the device and on the
batteries are clean, is necessary clean
them.Exposure
NoteStatement
the polarity (+/-) when inFCC Radiation
This equipment complies with FCC RF radiation exposure limits set forth for an
serting the batteries. Do not throw
uncontrolled environment. This transmitter should be installed and operated
with athe
minimum
distance of 20 centimeters
and your
batteries
into abetween
fire,the radiator
short-cirbody and must not be co-located or operating in conjunction with any other
cuit
themThis or
dismantle
antenna
or transmitter.
equipment
complies with them.
Part 15 of theKeep
FCC Rules.
Operation is subject to the following two conditions:
away
from
batteries.
Seek
(1) Thischildren
device may not cause
harmful
interference,
and
(2) This device must accept any interference received, including interference
medical attention immediately if a
that may cause undesired operation.
battery is swallowed. Do not attempt to
repair the device yourself; customer
service is available. Any changes or
modifications to this unit not expressly
approved by the party responsible for
compliance could void the user’s authority
EU Declaration of Conformity
We, Netatmo, declare that this device is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
to operate the equipment. Thermostat and
relay insulation: class II devices. This
device is not intended for use by
persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure
Canadian Compliance Statement
Thisthat
devicethey
complies
withnot
Industry
Canada
RSS standard(s).
do
play
withlicense-exempt
the appliance.
Operation is subject to the following two conditions: (1) this device may not
Legal
notice
cause
interference,
and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Use of the HomeKit logo means that
Cet appareil est conforme aux normes CNR exemptes de licence d'Industrie
Canada.
fonctionnement est
soumis aux deuxhas
conditions
suivantes:
an Leelectronic
accessory
been
de-(1) cet
appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter
connect
specifically
iPod,
toutesigned
interférence,to
y compris
celles susceptibles
de provoquer to
un fonctionnement
non souhaité de l'appareil.
or iPad,
respectively,
and has
ThisiPhone,
Class B digital apparatus
complies
with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
been certified by the developer to meet
Canada.
ThisApple
device and
its antenna(s) muststandards.
not be co-locatedApple
or operating
performance
is in
conjunction with any other antenna or transmitter.
not responsible
operation
of this en
Cet appareil
et son antenne (s) nefor
doit the
pas être
co-localisés ou fonctionnant
conjonction avec une autre antenne ou transmetteur.
device or its compliance with safety and
Taiwan Wireless Statements
regulatory standards.
無線設備的警告聲明
本產品符合低功率電波輻射性電機管理辦法 第〸二條、第〸四條等
Please note that the use of this acces條文規定: sory
1. 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使
用�均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 with iPod, iPhone, or iPad may affect wi2. 低功率射頻電機之使用不得影�飛航安全及干擾合法通信;經發
現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 reless performance.
前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性
電機設備之干擾。
Complies with
IDA Standards
V16
Copyright Netatmo © 2015 All rights reserved. Reproduction and distribution prohibited without written authorization from Netatmo.
V5-EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement