SWAIRS - Appliance Factory Parts

SWAIRS - Appliance Factory Parts
f
r
•
READ AND
SAVE THESE
INSTRUCTIONS
)
SWAIRS
S
owner's
manual
Stock No.
42-14416
Model No.
758.144160
QUIET COMFORT
WHOLE HOUSE
HUMIDIFIER
12 Gallon Output
FOR YOUR
SAFETY:
Innovative Twin Fan
Technology
READ
ALL INSTRUCTIONS
CAREFULLY
J
• Operating Instructions
• Parts List
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Part No. SP6423
Printed in Canada
r
FULL
ONE YEAR WARRANTY
ON HUMIDIFIER
--
If within one (1) year from the date of purchase, this humidifier fails due to a defect in
material or workmanship, Sears will repair it, free of charge. If within two (2) years from
the date of purchase, the motor fails due to defect in material or workmanship, Sears
will repair it free of charge.
This warranty service is available by simply returning the humidifier to the nearest Sears
Store, and it will be repaired or replaced, at Sears option, free of charge.
This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179
k,_
..,=
GENERAL SAFETY INSTRUCTIONS
Safety
Signal
Words
DANGER: means if the safety information
is not followed, someone will be seriously
injured or killed.
WARNING: means if the safety information
is not followed, someone could be seriously injured or killed.
CAUTION: means if the safety information
is not followed, someone may be seriously
injured or killed.
1. To reduce the risk of fire or shock hazard,
plug humidifier directly into a 120V,A.C. electrical outlet. Do not use extension cords.
2. Keep the electric cord out of traffic areas.
To reduce the risk of fire hazard, never put
the electric cord under rugs, near heat
registers, radiators, stoves or heaters.
3. Always unplug the humidifier before
moving it, before cleaning, or whenever
the humidifier is not in service.
4. Keep the humidifier clean.
5. Do not put foreign objects inside the
humidifier.
6. Never use your humidifier while any part
is missing or damaged in any manner.
7. To reduce the risk of electrical hazard or
damage to humidifier, do not tilt, jolt or
tip humidifier while unit is running.
8. To reduce the risk of damage to humidifier, unplug humidifier, when humidifier
cabinet is empty or when the humidifier
is not in use.
9. To reduce the risk of accidental electrical shock, do net touch the cord or controls with wet hands.
10.Note the warning label shown below
and on the humidifier.
WARNING: To avoid fire or shock hazard:
1. Unplug humidifier before filling.
2. Close the control cover.
3. Fully open front acceee door.
4. If controte get wet, let them dry completely. Have
unit checked by authorized personnel before plugging back in.
5. Do not overfill.
Table of Contents
Warranty Information ..................................
General Safety Instructions ........................
To Save A Service Call ...............................
Know Your Humidifier .................................
2
2
2
3
Humidifier Operations
................................
Assembly ....................................................
Location Instructions
..................................
Electrical Hook-Up ......................................
4
4
5
6
To Save a Service Call
Check the following if your humidifier will
not operate.
1. ts power cord attached to outlet?
2. Is there electrical power to outlet?
Water
Fill .....................................................
6
Operating Humidifier Controls
................... 7
Manual Dryout .............................................
7
Using Your Humidifier .................................
8
Operating Tips for Best Performance ......... 8
Replacement
and Care of Filters ........... 9-10
Cleaning Your Humidifier ..................... 11-12
Troubleshooting
.......................................
t3
Repair Parts .........................................
14-15
3. Is airflow control in operating position?
4. Is humidity control set high enough?
5. Is there enough water in the humidifier
cabinet?
Know Your Humidifier
Pivoting Lid Removed for Clarity
Fan Assembly
Controls
_lash Guard
Lid
Filter
Housinq
Filters:
Replacement
Filter 42-14912
Description
42-14416
Gallon Output/24 Hrs.
Water Reservoir Capacity
Sq. Ft. Coverage
Fan Speeds
Filters
Water Level Indicator
Fill Indicator
Auto Humidistat
Auto Shut Off
Controls
CUL Listed
Volts
Hertz
Amps
Watts
12
4.75 Gallons
2500
3
4 Pack (42-14912)
Yes
Yes
Yes
Yes
Rotary
Yes
120 A.C.
60
2.28
130
Based on an area with average insulation and
an 8 foot ceiling height.
Humidifier
Operations
Your new Sears humidifier is designed to
satisfy
home humidity
requirements
through the principle of evaporation of
water into the air.
After water is added to the cabinet, the filters begin to soak up the water and
become totally saturated in approximately
30 minutes. Air is drawn in from the rear of
the humidifier and through the filters by
means of circulation fans. As air passes
through the filters, moisture is absorbed
into the air and then released through the
top of the humidifier. This moist air is
released in the form of vapor. No water
droplets will enter the home. All evaporation into the air takes place in the humiditier, which means that the residue left by
evaporating water is not passed into the
home, but remains in the filter.
CAUTION: Use only 42-14900
EPA
Registered
Bacteriostat
available
from SEARS Retail store. Under no
circumstances should you use water
treatment products designed for Roto
be t or U trason c hum d f ers.
Humidified Air is Then
Released Through the Top
Dry Air Enters
Through the
Rear
'
"it
"_ d
CAUTION:
Keep
your
humidifier
clean. While humidifiers do not cause
colds, some studies suggest that dirty
humidifiers can cause cold-like symptoms in some people. To reduce the
risk of this, we recommend you clean
your
humidifier
weekly
with
Humidifier Cleaner 42-14713 and use
Bacteriostat
42-14900.
These are
available at your local Sears store
Assembly
Your new Sears
Kenmore
humidifier
is
completely assembled for you to use.
Remove the packaging
material from
inside your humidifier
and follow the
instructions of this owner's manual for
proper usage. The packaging material is
located below the fan assembly. Remove
all of the packaging material and discard.
NOTE: The filters may have shifted
during shipping. Ensure that they are
properly seated in the bottom of the
cabinet below the top filter housings
before filling. Refer to "Replacement
and Care of Filters" section on page 9.
Location Instructions
WARNING: For your own safety, do I
not use humidifier if any parts are
damaged or m ss ng.
Step 1
Place humidifier on a flat level surface in
an area of the house where most humidity is needed, or one which would likely
result in moist air being circulated
throughout the house such as near a cold
air return.
Placing the unit level is very important. Be
sure to verify that unit is level if the humidifier is located on carpeting.
Moist air (humidity) produced will disperse
into the whole house, but area closest to
the unit will have the highest humidity, tf
the unit is positioned close to a window,
condensation may form on the window
pane. if this is not appropriate the unit
should be repositioned in another location.
NOTE: Due to release of cool, moist air
from humidifier, it is best to direct air away
from home thermostat and hot air regis-
I
ters. it is best to position humidifier next to
an inside wall. Hot air registers and cold
air from outside walls can affect the efficiencies of the controls. Unit should not be
placed where warm air from a hot air register blows directly on unit.
Step 2
The humidifier should be positioned with
the back (cord exit side), at least 2 inches
away from the wall. Air needs to enter
through the louvers in the rear of the cabinet in order for the humidifier to operate at
peak efficiency
At Least 2" From Wal!
,i1,,,1--
Electrical Hook-Up
Locate nearest 120V A.C. wall socket in
the location desired, preferably on inside
wall. Plug in the electrical cord.
reverse plug. if it still does not fit, contact
a qualified electrician to install the proper
outlet. Do not change the plug in any
way.
WARNING: To reduce the risk of fire
or shock hazard, humidifier should
be plugged into a 120V A.C. outlet.
Do not use extens on cords.
To reduce the risk of electrical shock, this
humidifier has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one way.
if the plug does not fit fully in the outlet,
Water Fill
WARNING: To reduce the risk of shock,
always unplug humidifier before cleaning or servicing.
the "FULL" labels positioned to the left and
right at the bottom inside of the cabinet.
These
labels
indicate
the maximum
WARNING: To reduce the risk of fire or
shock hazard, do not pour or spill water
into control or motor area. Close the
amount of water that can be poured into
the humidifier.
control cover. If controls get wet, let
them dry completely and have unit
checked by an authorized service personnel before plugging in.
This humidifier is designed to be filled
using a bucket fill method. The unit should
be positioned where it will be operating. To
fill the humidifier, close the control cover
and open the pivoting lid. Notice the splash
guard inside the cabinet of the humidifier.
Use recommended mixture of cold water
and if necessary Sears Bacteriostat #4214900 only. Pour the water slowly from a
bucket into the cabinet onto the center of
splash guard. NOTE: Deflect water off center of splash guard when filling. The water
deflects off the splash guard and drops into
the bottom of the cabinet. Do not pour
water onto top of unit or control area.
Standing in front of the humidifier, notice
Do not fill water in the cabinet above
this line. If you do, water will leak out of
the cabinet and onto the floor.
NOTE: Deflect water off center of
splash guard when filling.
Pivoting Lid
Cabinet
Front of Humidifier
Operating Humidifier
Controls
The operating controls of your Kenmore
Quiet Comfort Whole House humidifier are
located on the top center of the humidifier.
The controls are found under the smoked
control cover, located between the air circulating fans.
Lift the control cover by placing your finger
in the round cutout and lifting. The cover
will stay open. Now you can clearly see the
control area. Familiarize yourself with the
controls and reference the diagram of the
control area for the correct naming used in
this manual.
To Operate
NOTE: The cabinet may have a small
amount of water in it once unit shuts off.
Manual Dryout
At the end of the humidification season or if
the Controls
Humidity Control:
Adjust the amount of humidity depending on
your needs. The humidifier will turn on and
off as required to maintain level of humidity
selected. A medium setting is recommended, but there are times when a low or high
amount of humidity may be preferred. For
constant operation of humidifier, turning the
control all the way clockwise allows for the
maximum amount of humidity to be evaporated into the air continuously.
IMPORTANT: Water damage may result
if condensation starts to form on windows or walls. Humidity Control setting
should be lowered until condensation
no longer forms.
Speed Control
Your Kenmore humi_r
has a three
speed rotary fan control. The higher the
air flow speed, the more water is evaporated and released into the air. Low speed
( • ) is the quietest and is provided for
conditions that may not require as high an
evaporation rate.
Water
Fill Indicator
When the unit has a small amount of water
left in it, the small window next to Fill on the
control panel will appear orange and the
unit will automatically shut off.
Level Indicator
This humidifier is equipped with a water level
gauge located in the center of the control panel.
When the cabinet is full of water the large window opposite the scale will show green. As
water is depleted the amount of green will
decrease to correspond with the scale.
Water Gauge
Fill Indicator
you do not plan to run the
humidifier for one week or more, you can
override the automatic shutoff function to
completely dry the humidifier cabinet out.
To do this, simply slide the link arm assembly retainer located at the back of the
humidifier cabinet to the top position of the
slot it is located in. This will hold the float in
an upward position and the fans will run until
you turn the power off.
NOTE: Be sure to position link arm assembly retainer to the normal operating mode
(lowest position in slot) for humidifier operation.
Below is a diagram of the slot the link arm
assembly retainer is located in at the back of
the cabinet.
Back of Oabinet
TOP POSITION
IS FOR MANUAL
DRYOUT
BOTTOM POSITION
IS FOR NORMAL
OPERATION MODE
LINK ARM
ASSEMBLY
RETAINER SLOT
Using Your Humidifier
Step 1
Be sure humidifier
Step 4
is full of water
and
plugged in.
Step 2
Set Speed Control _
Step 3
Set Humidity Control
position.
to low speed ,,o,
@
to a medium
NOTE: Humidifier
should operate with
humidity control on the recommended
medium setting, tf it does not, the humidity
is at a relatively high level. To test the unit
under this condition, turn Humidity Control
all the way clockwise and unit should begin
to operate. After the unit has been tested,
set Humidity Control to medium or desired
level.
Allow 24 hours for humidifier to adjust.
If humidifier stops running and the unit is
not empty the humidity level is at the normal requirements for that setting or it is
adjusting to the home conditions. The table
below shows recommended indoor humidity levels. The figure below shows approximate relative humidity percentages which
correspond to the various settings of the
Humidity Control.
Recommended
Indoor Relative
When Outdoor
Temperature
is:
Humidity is:
-10°F
0°F
10°F
20°F & above
20%
25%
30%
35%
If humidity level in home is sufficient, the
humidifier will only operate with Humidity
Control turned al! the way clockwise.
IMPORTANT: Water damage may result
if condensation starts to form on windows or walls. Humidity Control setting
should be lowered until condensation
no longer forms.
Relative
Operating
Humidity
Tips for Best Performance
1. Position the humidifier at least 2 inches
from any wall and away from any heat
registers.
2. Do not restrict airflow from entering or
exiting the humidifier.
3. Use Sears recommended bacteriostat
42-14900 to retard bacteria growth that
may cause odors and may be harmful
to your health.
4. Perform regular cleaning as instructed
in "Cleaning Your Humidifier" section of
this manual.
5. Replace the evaporative wicking filters
at least once per humidification season
or more depending on water conditions
in your area.
Replacement
and Care of Filters
WARNING: To reduce the risk of shock
or injury from moving parts, always
unplug humidifier before removing or
replacing any parts.
Pivoting
Lid
Fan
Assembly
CAUTION:
To help retard bacteria
growth and keep maximum efficiency,
the filters should be replaced at least
once per season, or more often under
hard water conditions. Use Sears recommended replacement filter 42-14912.
All filters may be rinsed in clear water only.
Take care not to damage paper. To replace
evaporative wicking filters in your Kenmore
Quiet Comfort Whole House humidifier, follow the instructions below.
1. Unplug humidifier and proceed to clean.
Before removing the filters, we recommend moving the humidifier to an area
where floor coverings are not susceptible to water damage, i.e. kitchen or bath
areas.
Tab on
Front
Fitler
Housing
Top Filter
Housings
Link Arm
Assembly
2. To remove parts
Remove the fan assembly by opening
the pivoting lid. Grasp the fan assembly front center and rear center. Lift off
and set aside on a clean flat surface.
The filter housing assemblies are now
accessible.
NOTE: There are two filter housing
assemblies.
Each assembly
consists of a top filter housing and a
front filter housing. The front filter
housing contains tabs that secure
the top filter housing.
Do not
remove the front filter housings.
3. To remove top filter housing, deflect
the two vertical tabs on top of front filter housing and lift up and out of cabinet. With a soft, absorbent
cloth
remove any remaining water or loose
mineral deposits not trapped in the filter from the filter housing assemblies.
4. Remove the two filters and dispose of
properly. Repeat for other top filter
housing. Clean internal parts of humidifier per the "Cleaning of Humidifier"
section of this owner's manual.
Front of
Humidifier
_
Float
(top v_ssembly
Link
i
_
.etainer
Exploded
/_'r_i_
t Piv°t
/
View of Float Assembly
Replacement
and Care of Filters
5. a. Install new filters (42-14912)
bottom of the cabinet.
(continued)m
in the
OO0000000000V2_
NOTE: The new filters will only fit into
the cabinet one way. Take note of the
inner cabinet detail where the filters
sit. Each pair of filters must be positioned so the glue beads face out
from each other. Refer to figure 5a.
b. Place the filters into the bottom of the
ITabs
cabinet so the open pleats slip over
the tabs in the bottom of the cabinet
Repeat for other side.
Front Filter Housing
Front of Humidifier
Figure 5a. - Filter Locations Marked X
c. Reposition top filter housings on top
of filters and snap into front filter
housings.
d. Position fan assembly onto the cabinet. Make sure the fan venturi (lowest cylinder section below the fan) is
placed inside the top filter housings.
e. Close the pivoting
assembly.
Tab on
Front
Filer
Housing
lid on the fan
Top Filter Link Arm
Housim IS Assembly
/ Retainer
_O00EX/L/!/OOEY/\
f. The unit is ready for use or to be
stored away for next season.
Front of
Humidifier
(top view)
10
Float
Assembly
Cleaning Your Humidifier
WARNING:
To reduce the risk of
injury, fire or damage to humidifier,
use only cleaners specifically recommended
for humidifiers.
Never
use flammable, combustible or poisonous
materials
to clean your
humidifier.
To reduce the risk of
Step 2
To Remove
Parts
a. Remove the fan assembly by opening
the pivoting lid. Grasp the fan assembly front center and rear center. Lift off
and set aside on a clean flat surface.
b. Before removing the internal parts of
the humidifier cabinet, we recommend
moving the humidifier to an area where
floor coverings are not susceptible to
water damage, i.e. kitchen or bath
area.
scalds and damage to humidifier,
never put hot water in humidifier.
CAUTION: Local water purity varies
from area to area and under certain
conditions water impurities and airborne bacteria
may promote
the
growth of microorganisms
in the
reservoir of the humidifier.
c. Deflect the two vertical tabs on top of
the front filter housing to release the
top filter housing. Lift top filter housing
straight up and out of cabinet. Repeat
for other top filter housing.
d. Remove old filters and dispose of properly.
e. Remove the water level float assembly
from the humidifier cabinet by pinching
the link assembly retainer to disengage
it from the rear of the cabinet. See diagram on page 9.
To retard bacteria growth that may
cause odors and be harmful to your
health, use only Sears replacement
filters. We also recommend using
EPA approved bacteriostat, 42-14900
and humidifier
cleaner 42-14713,
available at your local Sears store.
NOTE: If it is necessary to use approved
bacteriostat, follow directions correctly.
The cabinet of the whole house humidifier
will hold 4-3/4 gallons.
Step 1
To make cleaning easier, the humidifier
cabinet should be empty and completely
dried out. To accomplish this, use the fo!lowing method:
a. On the back side of the humidifier cab-
f. Empty cabinet of any remaining water.
g. Proceed to "Bi-Weekly Maintenance"
or "End of Season Maintenance" and
then continue as described below.
Step 3
Install new filters (Kenmore 42-14912
Replacement
Filters) into the location
where the old filters were positioned.
Reinstall the water level float assembly
into the cabinet.
inet, find the link arm assembly retainer. In normal operating mode, the
retainer will be positioned in the bottom
of the slot in the cabinet. Push the
NOTE: Link arm assembly retainer should
be positioned in normal operating mode.
Assure that it is positioned in the bottom of
the slot in the back of the cabinet. (See
page 7 for diagram of slot.) Reposition top
filter housings on top of filters and snap
onto front filter housings. Position the fan
assembly on top of the cabinet and return
the humidifier to the desired location for
use. Refill humidifier cabinet with fresh
retainer up to the top slot position in the
cabinet until it locks into place. (See
"Manual Dryout" section on page 7.)
b. Allow the humidifier tp run until there is
no water left in the cabinet.
c. Unplug humidifier.
cool water. Plug the unit into a 120 volt
A.C. power outlet and set the controls per
the "Operating Humidifier Controls" section of this manual.
plugged, fan could start after housing
I is ARNING:
removed. If humidifier is not un- I
11
Cleaning
Bi-Weekly
of Humidifier
(continued)
End of Season
Maintenance
Removing Scale
1. Fill the humidifier
Maintenance
1. Follow
"Bi-Weekly
Maintenance"
instructions at end of humidification
season.
cabinet with one 8
oz. cup of undiluted white vinegar. Let
solution stay 20 minutes.
2. Clean all interior surfaces with a soft
brush. Dampen a soft cloth with undiluted white vinegar and wipe out the
cabinet to remove scale.
2. Remove and throw away filters.
3. Let humidifier dry completely before
storing. Do not store with water inside
cabinet.
4. Store in cool, dry location.
5. Install new filters in clean humidifier
before next season begins.
6. "Bi-Weekly Maintenance" is also recommended if you do not plan to use
the humidifier for one week or more.
3. Rinse thoroughly
with clean warm
water to remove scale and cleaning
solution before disinfecting the humidifier cabinet.
4. Dust the fan assembly and outside surfaces with a soft cloth only.
Disinfecting Humidifier Cabinet
1. Fill humidifier cabinet with 1 teaspoon
chlorine bleach in I gallon of water. Let
solution stay for 20 minutes, swishing
every few minutes. Wet all surfaces
normally exposed to water.
2. Empty humidifier cabinet after 20 minutes. Rinse with water until bleach
smell is gone. Allow unit to dry out
completely.
12
Troubleshooting
TROUBLE
PROBABLE
Unit will not run.
• Selected humidity
been established
CAUSE
REMEDY
level has
• No power
Unit
off
will
not
shut
Unit will not dry out
completely
• Float assembly positioned
"Manual Dryout" position
setting if desired
• Check
120 volt source for power
• Float is not free
• A small amount of water will
remains in cabinet when water
• Position
"Manual
Unit is not
emptying during
use
• Dirty filters
Water runs out of
• Water splashing
reads FILL.
during
filling.
float assembly in
Dryout" position. (See
page 7)
• Change
rear of unit
Water level gauge
humidistat
• Slide link arm assembly retainer
to lowest position in slot at back
of cabinet. (See page 7)
• Free float from obstruction
level indicator
in
• Raise
• Deflect
to fresh new filters
fill water off the center
the splash
of
guard
• Too much water added
• Do not overfill past "Full" label in
cabinet
• Filters interfering
• Be sure filters are positioned
with float
not functioning
properly,
erly in bottom of cabinet.
page 9.)
CAUTION: Use only 42-14900 EPA Registered
Retail store.
Use of other water treatment
prop-
(See
Bacteriostat available from Sears
products may damage the filter elements.
Under no circumstances should you use water treatment
Roto belt or Ultrasonic humidifiers.
13
products designed for
p_
25
I
24
_,..I
_J
I
I
I
I
I
I
21
z._,
2t
t,,.
o_
_J
Key
No.
Part No.
1
2
3
4
828743
828756
828760
828741
5
6
7
8
9
828855
822409
823912
828754
828898
10
11
12
13
14
15
828747
828748
828744
824120
828757
828746
16
17
828758
828759
Description
Key
No.
Cover, Dust
Knob
18
19
STD601107
828515
* Screw, Pan Hd. Ty "AB" #10 x 3/4
Caster, Twin Wheel
Label, Control
20
21
22
23
42-14912
828194
828195
828534
1-Filter, Evaporative
Housing, Top Filter
24
25
26
27
28
828115
822406-1
828998
823726
816069-5
29
30
-
STD6OO805
828907
SP6423
Lid, Stationary
Lid, Pivoting
Humidistat
Switch, Rotary
Spring, Torsion
Switch, Micro
Wheel, Indicator
Retainer, Micro Switch
Enclosure, Electronics
Cord w/Plug
Retainer, Link Arm Assembly
Float, Water Level
Part No.
Description
o
Housing, Front Filter
Support Motor
Motor (Includesmounting hardware)
Fan
Cabinet
Rail Kick
* Screw, Pan Hd. Type AB #6 x 1/2
* Screw, Pan Hd. Ty. "AB" #8 x 1/2
Motor (Includes Lead)
Owner's Manual (Not Illustrated)
Arm, Float Pivot
Push, Arm
z,l_I
•<
€-
3
o"
* Standard Hardware Item - May be purchased
locally.
1 Stock Item - May Be Secured Through Sears
Retail and Catalogue Stores.
_.
Notes
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii;i!ii?
.......
111111111111!
¸_......
YourHome
For repair-in your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(,-8oo-469-4663)
ca,,
anyt,me,
day
orn,0ht/0.S.A,
and
Canada)
www,sears.com
www.sear_.ca
OurHome
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center,
1-800-488-1222
Ca,,
anyt,me,
day
o_n,oht/O.S.A,
on,y)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655
(U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-800-361-6665
Au Canada
(1-888-784-6427)
_} Registered
Trademark
/ Try1Trademark
[ sr_l Service Mark of Sears
Roebuck
and Co
_,
,_ Marca Registrada
/ T M Marca de F_brica / SMMarca de Servicio
de Sears.
Roebuck
and
,_c Marque
de commerce
/ MD Marque d6pos6e
de Sears, Roebuck
and Co
Form. No. SP6423-1
pour service en frangais:
1-800-LE-FOYER M°
1-888-SU-HOGAR SM
Part No. SP6423
(Canada)
(1-800-533-6937)
www.sears.ca
Co
(c_ Sears,
Roebuck
and Co.
Printed in Canada 06/04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising