Yamaha | MG06X | Owner's Manual | Yamaha MG06X Owner's manual

Mixer Basics:
Where Your Sound Goes
Owner’s Manual
Thank you for purchasing the Yamaha MG06X/MG06 Mixing Console.
Please read this manual thoroughly to get the most out of the product and ensure long-term,
trouble-free use. After reading this manual, keep it readily available for future reference.
* For the remainder of this manual, the word “mixer” is used instead of “Mixing Console.”
** In this manual, all panel illustrations show the MG06X panel.
• 6-channel mixer features microphone inputs and stereo/mono line inputs for input jacks.
• Yamaha’s premium head amp “D-PRE” for providing high quality sound.
• PAD switch to support a wide variety of inputs to the channels 1/L and 2/R.
• (MG06X) Yamaha’s high-quality SPX effects (6 types), providing optimum processing for
instruments or vocals.
Channel 2/R
Channel number
instruments, etc.
Turn on the power to connected devices in the following order:
(audio device)
[ ] (switch on unit)
Set the [STEREO LEVEL] knob to the “3” position.
For channels to which a microphone is connected, set the [GAIN] knob to
roughly the 12 o’clock position.
Connection Example
Electric acoustic guitar
Electric keyboard
Applying Effects (MG06X)
The MG06X features built-in effects (Reverb and Delay) processors that are in the same
league as our famed SPX effect processor series. Those effects let you simulate the
acoustics of different performance environments, such as concert halls and small clubs,
and add warm, natural ambience to your vocals or instrument performance.
Reverb simulating a large space such as a concert hall.
Reverb simulating the acoustics of a small space (room).
Reverb simulating a metal-plate, producing a more hard-edged sound.
Short echo with a “doubled” sound.
Long, resonant echo with an extended decay.
Echo suitable for vocals.
Controls and Functions
While playing your instrument or speaking into the microphone, turn the
[LEVEL] knob to adjust the volume of the corresponding channel.
Connect a microphone, an instrument, or an audio device (CD
player, etc.) to the unit. These jacks support both XLR and
phone plugs.
Connect line-level devices such as an electric keyboard or
an audio device. These jacks support phone plugs. If you use
only the [L/MONO] jack, same sound is output from both L (left)
and R (right) speakers.
4[PAD] switches
If necessary, adjust the volume of the speaker or power amp.
If you hear the sound and the volume seems appropriate, setup is complete. If not,
please go to step 10 below.
NOTICE To avoid any loud noise from the speaker, first turn off the power of the speaker (speaker amp), then
the unit itself, and finally the connected sound source such as an instrument.
10 If the sound is not heard, or if you want to adjust the volume, follow the
instructions in the boxed section below.
If you still do not hear the sound after doing the following steps, please refer to the
checklist in the “Troubleshooting” section at the back of this booklet.
< There is no sound, or you need to increase the volume
* Stereo mini plugs require conversion plugs to phone plugs.
STEP 2 Getting Sound to the Speakers
1 Make sure that all switches including the [ ] switch are not pressed (N).
2 Connect the supplied AC power adaptor.
First connect the adaptor to the DC IN [12V] jack at the back panel of the unit (1),
and then to the outlet (2).
Connect a powered speaker or powered amp. These jacks
support both XLR and phone plugs.
7[PHONES] output jack
Connect a set of headphones. This jack supports a stereo
phone plug.
turned fully to the right, raise the volume of the sound source
(instrument, etc.).
If no sound is heard or the volume does not increase after step 1:
To electrical outlet
If the [PAD] switch is turned on (O), set the [LEVEL]
knob to “0” (minimum), and then turn off (N) the
Turn the [GAIN], [LEVEL] knobs (white), and [STEREO LEVEL] knob (red)
fully to the left (minimum). Set the equalizer knobs (green) to the center “6”
Refer to the illustration (at the top of the next column, before step 4).
When this switch is on (O), the LED lights indicating that the
unit supplies DC+48V phantom power to the XLR plugs of
the [MIC/LINE] mono input jacks 2. Turn this switch on when
using a phantom-powered condenser microphone.
NOTE Turn the [LEVEL] knob to "0" (minimum) before toggling
the [PAD] switch on (O) and off (N). Otherwise, noise
may be produced.
5[HPF] (High-Pass Filter) switches
Turning the switch on (O) will apply a high-pass filter that
attenuates frequencies below 80Hz. When speaking into the
microphone, you may want to turn this switch on (O), in order
to reduce unwanted vibration and wind sound received by the
Slowly turn the [LEVEL] knob to the right until the
desired volume is reached.
Lower the volume of the instrument or audio device.
Be sure to leave this switch off (N) if you do not need phantom power.
Follow the important precautions below, in order to prevent noise and
possible damage to external devices as well as the unit when you
operate this switch.
• Be sure to leave this switch off when you connect a device that does
not support phantom power to channels 1/L or 2/R.
• Do not connect/disconnect a cable to/from channels 1/L and 2/R
while this switch is on.
• Turn the [LEVEL] knob of the channels 1/L and 2/R to the minimum
before operating this switch.
] (On/Standby) switch
Toggles to turn the unit’s power On (O) or Standby (N).
• Rapidly switching the unit between on and standby in succession
can cause it to malfunction. After setting the unit to standby, wait for
about 5 seconds before turning it on again.
8[GAIN] knobs
Determines the basic volume for each channel, 1/L and 2/R.
Adjust these so that the corresponding [PEAK] LEDs @ flash
briefly when singing or playing the loudest.
9Equalizer (EQ) knobs
Adjust the sound quality by using the [HIGH] (high frequency
band) and [LOW] (low frequency band) knobs. If you do not
need to adjust the sound quality, set the knob to the “6” (flat)
)[FX] switches (MG06X)
Set the [LEVEL] knob to “0” (minimum), then turn on
(O) the [PAD] switch.
If the volume does not decrease after the above steps:
^[PHANTOM +48V] switch/LED
Slowly turn the [LEVEL] knob to the right until the
desired volume is reached.
< To decrease the volume:
Turning the switch on (O) will attenuate the sound input to the
unit. If you hear distortion or the [PEAK] LED @ lights, turn the
switch on (O).
Turn the [GAIN] knob to the right so that the corresponding [PEAK] LED flashes briefly.
NOTE If the [PEAK] LED does not light even if the [GAIN] knob has been
6[STEREO OUT] output jacks
3[LINE] stereo input jacks (channels 3/4, 5/6)
Power adaptor
Connect the supplied AC power adaptor to this jack.
Turn the [FX RTN LEVEL] knob to adjust the effect amount.
1(Back panel) DC IN [12V] jack
Turn on (O) the [FX] switch of the channel (1/L or 2/R) to which you want to
apply the effect.
Powered speakers
The LED of the selected effect lights.
2[MIC/LINE] mono input jacks (channels 1/L, 2/R)
Move the effect select slide switch up and down to select the effect type.
Use the [REVERBN /O DELAY] switch to select Reverb (N) or Delay (O).
NOTICE Follow this order to avoid any loud, unexpected noise from the speakers. Reverse the order when
turning the power off.
mixed sound
the channels to the final output.
4 Final adjustment of the volume of the
3 The signal flow of the sound rightward, from
Quick Start Guide
STEP 1 Connecting speakers, microphones, and
Equalizer (HIGH, LOW) knobs
NOTE If you are using condenser microphones, turn on (O) the [PHANTOM +48V] switch.
Included Accessories
2 Adjust the sound quality and volume of each
* Channel: Location or path where sound is input.
Channel 1/L
5 Output the sound from speakers or
If you connect a device with high output level, such as a CD player or an
electric keyboard to the channels 1/L and 2/R, turn on (O) the [PAD] switch
of the corresponding channel*.
Main Features
• AC power adaptor
• Technical Specifications: Includes block diagram, dimensions, general specifications, and
input/output characteristics.
Manual (this leaflet)
The right illustration diagram illustrates the sound
flow from summing (mixing) sound which was
input to the channels to outputting sound from
the speakers or headphones. Let’s find out where
input sound goes once it’s inside the mixer.
1 Input the sound from a microphone or
Toggle the FX (effect) of channels 1/L and/or 2/R on and off.
![N MONO/O STEREO] switch
• Even when the switch is in the standby (N) position, electricity is still
flowing to the unit. If you do not plan to use the unit for a while, be
sure to unplug the AC power adaptor from the outlet.
Lights when the volume of input and/or post-equalizer sound
is too high. If it is lit, turn the [GAIN] knob 8 to the left to lower
the volume.
#[LEVEL] knobs
For adjusting the volume balance among the channels.
(N) [MONO]: Sound input to channels 1/L or 2/R can be
heard from both the right and left speakers. If you use the 1/L
or 2/R individually, set the switch to this setting.
(O) [STEREO]: Sound input to channel 1/L can be heard from
only the left speaker, and that input to channel 2/R can be
heard from only the right speaker.
Adjusts the headphones volume.
Adjusts the overall volume output from the [STEREO OUT]
output jacks.
*[REVERBN /O DELAY] switch (MG06X)
Toggles to select the effect applied to channels 1/L and 2/R
between Reverb (N) and Delay (O).
(Effect select slide switch (MG06X)
Moves up and down to select the effect type. The LED of the
selected effect lights.
A[FX RTN LEVEL] (effect return level) knob
Adjusts the volume of the effect sound.
BLevel meter
The L and R meters show the level of the signal output from
the [STEREO OUT] jack. If the [PEAK] lamp lights in red, use
the [LEVEL] knob to lower the volume.
General Specifications
All level knobs are nominal if not specified.
Power does not come on.
Frequency Response
+0.5 dB/-0.5 dB (20 Hz to 20 kHz),
refer to the nominal output level @ 1 kHz, GAIN knob: Min
Did you properly plug the power adaptor into an appropriate AC outlet?
Total Harmonic Distortion
0.01 % @ +8 dBu (20 Hz to 20 kHz), GAIN knob: Min
0.003 % @ +18 dBu (1 kHz), GAIN knob: Min
Hum&Noise *1
Equivalent Input Noise
-128 dBu (Mono Input Channel, Rs: 150Ω, GAIN knob: Max)
(20 Hz to 20 kHz)
Residual Output Noise
-102 dBu (STEREO OUT, STEREO LEVEL knob: Min)
Did you firmly and securely connect the power plug?
No sound.
Did you turn on the powered speaker or the power amp?
Did you properly connect the microphones, external devices, and speakers?
Crosstalk (1 kHz) *2
-88 dB
Input Channels
6 channels: Mono (MIC/LINE): 2, Stereo (LINE): 2
Ouput Channels
Are any connecting cables shorted or damaged?
Did you properly set the [LEVEL] knobs of all relevant channels and the [STEREO LEVEL]
knob to appropriate levels?
Are the [PAD] switches turned on (O)?
Turn the switch off (N). If the volume of sound source is too soft, turning on the switch may
result in no audible sound.
Please keep this manual in a safe place for future reference.
Always follow the basic precautions listed below to
avoid the possibility of serious injury or even death
from electrical shock, short-circuiting, damages, fire or
other hazards. These precautions include, but are not
limited to, the following:
26 dB
80 Hz, 12 dB/oct
Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving
Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving
LED turns on when post EQ signal reaches 3 dB below clipping
(+11 dBu)
Level Meter
2 x 7-segment LED meter [PEAK (+11), +6, +3, 0, -3, -10, -20 dB]
Internal Digital Effect (MG06X)
SPX Algorithm
6 programs
Mono Input Channel Function
Power supply/AC power adaptor
Phantom Power Voltage
+48 V
Are the [GAIN] knobs and [LEVEL] knobs of all relevant channels, and the [STEREO LEVEL]
knob set too high?
Power Supply Adaptor
PA-130 (DC12 V/1.0 A, Cable length = 1.8 m), 120 V, 60 Hz, or
MU18 (DC12 V/1.5 A, Cable length = 1.5 m), 100 V-240 V, 50 Hz/60 Hz,
or an equivalent recommended by Yamaha
Power Consumption
12 W
Are the [PEAK] LEDs lit?
Lower the [GAIN] knobs of channels 1/L and 2/R, or turn on (O) the [PAD] switches.
Dimensions (W×H×D)
149 mm×62 mm×202 mm (5.9"x 2.4"x 7.9")
Net Weight
MG06: 0.9 kg (2.0 lbs), MG06X: 0.9 kg (2.0 lbs)
Are the “PEAK” (red) lamps of the level meter lit?
Set the [LEVEL] knobs of all relevant channels and the [STEREO LEVEL] knob to appropriate
Optional Accessory
Mic Stand Adaptor: BMS-10A
Operating Temperature
0 to +40°C
Is the volume from the connected device too loud?
Lower the volume of the connected device.
The sound of vocals and speech isn’t clear enough.
Turn on (O) the [HPF] switches.
The sound becomes clearer.
Adjust the equalizer knobs (example: lower the [LOW] knobs, raise the [HIGH] knobs).
No effect is applied. (MG06X)
Did you turn on (O) the [FX] switches?
*The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website
then download the manual file.
Jack List (Pin Alignment)
Input and Output Jacks
Pin 1: Ground
Pin 2: Hot (+)
Pin 3: Cold (-)
Tip: L
Ring: R
Sleeve: Ground
TRS phone plug
Are the [LEVEL] knobs of all relevant channels raised enough?
Did you set the [FX RTN LEVEL] knob to an appropriate level?
Tip: Hot (+)
Ring: Cold (-)
Sleeve: Ground
TS phone plug
LINE 3/4, 5/6
Tip: Signal
Sleeve: Ground
• If you intend to use the device in an area other than in the
one you purchased, the included power adaptor may not
be compatible. Please check with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt
or dust which may have accumulated on it.
• This device contains no user-serviceable parts. Do not
open the device or attempt to disassemble the internal
parts or modify them in any way. If it should appear to be
malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
MIC/LINE 1/L, 2/R*
• Only use the voltage specified as correct for the device.
The required voltage is printed on the name plate of the
Do not open
XLR connector
• Do not place the power cord near heat sources such
as heaters or radiators, and do not excessively bend or
otherwise damage the cord, place heavy objects on it,
or place it in a position where anyone could walk on, trip
over, or roll anything over it.
• Use the specified adaptor (MU18 or PA-130, or an
equivalent recommended by Yamaha) only. Using the
wrong adaptor can result in damage to the instrument or
*1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter.
Water warning
• Do not expose the device to rain, use it near water or in
damp or wet conditions, or place on it any containers (such
as vases, bottles or glasses) containing liquids which
might spill into any openings. If any liquid such as water
seeps into the device, turn off the power immediately and
unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
* These jacks also accept connection to TS phone plugs. If you use TS phone plugs, the connection will be unbalanced.
Fire warning
• Do not put burning items, such as candles, on the unit. A
burning item may fall over and cause a fire.
If you notice any abnormality
Mounting to a Microphone Stand
• If the stand should fall over, the mixer may be damaged. Attach the connection cables carefully so that the cables
will not catch on the equipment and cause it to fall. For example: arrange the cables so that they run parallel with the
microphone pole down to the base of the stand.
• When using the mixer on a microphone stand, be sure to set the stand on a level and stable surface. Do not set up
the stand in locations subject to vibrations or wind.
• Leave ample free space around the stand.
Turn the mixer upside-down, and hold the microphone-stand adaptor (BMS-10A; sold separately) against the bottom of the mixer so
that the screw holes are aligned (1). Screw the adaptor firmly into
place with the two screws (2).
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the
notices below.
and Maintenance
yyDo not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater,
or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the
internal components.
yyDo not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.
yyCondensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved
from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is
present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out.
yyAvoid setting all equalizer and level knobs to their maximum. Depending on the condition of the connected devices, doing
so may cause feedback and may damage the speakers.
yyWhen turning on the AC power in your audio system, always turn on the power amplifier LAST, to avoid speaker damage.
When turning the power off, the power amplifier should be turned off FIRST for the same reason.
yyAlways turn the power off when the device is not in use.
Turn the mixer right-side up, and mount it onto your microphone
Loosen the angle adjustment wingnut (1), adjust the mixer’s angle
as desired (2), and then tighten the wingnut securely (3).
Always follow the basic precautions listed below to
avoid the possibility of physical injury to you or others,
or damage to the device or other property. These precautions include, but are not limited to, the following:
Power supply/AC power adaptor
- The power cord or plug becomes frayed or damaged.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the device.
• If this device or the AC power adaptor should be dropped
or damaged, immediately turn the power off, disconnect
the electric plug from the outlet, and have the device
inspected by qualified Yamaha service personnel.
• When removing the electric plug from the device or an
outlet, always hold the plug itself and not the cord. Pulling
by the cord can damage it.
• Remove the electric plug from the outlet when the device
is not to be used for extended periods of time, or during
electrical storms.
• Do not place the device in an unstable position where it
might accidentally fall over.
• Do not place the device in a location where it may come
into contact with corrosive gases or salt air. Doing so may
result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet
you are using is easily accessible. If some trouble or
malfunction occurs, immediately turn the power off and
disconnect the plug from the outlet. Even when the power
is turned off, electricity is still flowing to the product at the
minimum level. When you are not using the product for a
long time, make sure to unplug the power cord from the
wall AC outlet.
3. NOTE:
This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your
use of this product in a residential environment will not result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found
in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with
FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be
the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of
America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
* This applies only to the MG06X distributed by YAMAHA CORPORATION OF AMERICA.
(class B)
Apparaten kopplas inte ur växelströmskällan (nätet) så
länge som den ar ansluten till vägguttaget, även om
själva apparaten har stängts av.
(class b korea)
Netspændingen til dette apparat er IKKE afbrudt,
sålænge netledningen sidder i en stikkontakt, som er
tændt — også selvom der er slukket på apparatets
Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko
laitetta verkosta.
• Remove the power plug from the AC outlet when cleaning
the device.
Handling caution
• Avoid inserting or dropping foreign objects (paper, plastic,
metal, etc.) into any gaps or openings on the device. If
this happens, turn off the power immediately and unplug
the power cord from the AC outlet. Then have the device
inspected by qualified Yamaha service personnel.
• Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons,
switches or connectors.
• Do not use speakers or headphones for a long period of
time at a high or uncomfortable volume level, since this
can cause permanent hearing loss. If you experience any
hearing loss or ringing in the ears, consult a physician.
Yamaha cannot be held responsible for damage caused
by improper use or modifications to the device, or data
that is lost or destroyed.
Always turn the power off when the device is not in use.
Even when the [ ](Standby/On) switch is in standby status,
electricity is still flowing to the instrument at the minimum
level. When you are not using the instrument for a long time,
make sure you unplug the power cord from the wall AC
European Models
Inrush Current based on EN 55103-1:2009
1 A (on initial switch-on)
1 A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used
electrical and electronic products should not be mixed with general household waste. For proper
treatment, recovery and recycling of old products, please take them to applicable collection points,
in accordance with your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any
potential negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier
for further information.
yyThe illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from
those on your device.
When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
• Before connecting the device to other devices, turn off the
power for all devices. Before turning the power on or off
for all devices, set all volume levels to minimum.
XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
this manual
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
yyWhen cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemicalimpregnated wiping cloths.
yyTo avoid generating unwanted noise, make sure there is adequate distance between the AC power adaptor and the device.
• When one of the following problems occur, immediately
turn the power off and disconnect the electric plug from
the outlet. Then have the device inspected by Yamaha
service personnel.
- It emits unusual smells or smoke.
yyDo not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise,
the device, TV, or radio may generate noise.
• Do not cover or wrap the AC power adaptor with a cloth or
Sound is faint, distorted, or noisy.
Are the [PAD] switches turned off (N)?
Turn the switches on (O). If the volume of sound source is too loud, turning off the switches
may result in distorted sound.
0 dBu = 0.775 Vrms Output impedance of signal generator (Rs) = 150 Ω
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact
your local authorities or dealer and ask for the correct method of disposal.
yyThe company names and product names in this manual are the trademarks or registered trademarks of their respective
The model number, serial number, power requirements, etc., may be found on
or near the name plate, which is at the bottom of the unit. You should note this
serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft.
Model No.
For more information, refer to the BMS-10A Owner’s Manual.
Serial No.
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying
the terminals in your plug proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
(2 wires)
Yamaha Pro Audio global website
Yamaha Downloads
Manual Development Department
© 2013 Yamaha Corporation
Published 03/2016 MWLE*.*- **C0
Printed in Malaysia
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF