100LBS SPIKE/SEEDER/SPREADER CT2210 INSTRUCTION

100LBS SPIKE/SEEDER/SPREADER CT2210

INSTRUCTION MANUAL

SAVE THESE INSTRUCTIONS AND PRECAUTIONS.

READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.

 

EC DECLARATION OF CONFORMITY

We CANNON TOOLS LTD

20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.

Declare that the following machine complies with the appropriate basic safety and health requirements of the EC Directive based on its design and type, as brought into circulation by us.

In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity.

Product description: SPIKE/SEEDER/SPREADER

Model: CT2210

Applicable EC Directives:

EC Machinery Directive 2006/42/EC

20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

Mr. Gurcharan Tony Singh Sanghera

Managing Director

CANNON TOOLS LTD

2016-01-18

2

ASSEMBLY & OPERATING INSTRUCTIONS

RULES FOR SAFE OPERATIONS

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. y Read this owner’s manual before attempting to assemble or operate the spiker/spreader. y Read the towing vehicle owner’s manual and know how to operate the tractor before using the spiker/spreader attachment. y Do not allow anyone to ride on or sit on the spiker/spreader. y Never allow children to operate the tractor or spiker/spreader attachment. y Do not allow adults to operate the tractor or spiker/spreader without proper instructions. y Wear eye and hand protection when handling and using lawn chemicals. y Do not drive too close to a creek or ditch and be alert for holes and other hazards which could cause you to loose control of the tractor and spiker/spreader.

ASSEMBLY INSTRUCTION

 

3

Step 1

Hex Bolt M6x65 3PCS

 

4

Step 2

Step 3

 

5

Step 4

Step 5

 

Step 6

6

Step 7

 

7

Step 8

 

OPERATION

How to use your spiker/spreader?

1. Determine the approximate square footage of the area to be covered and estimate the amount of fertilizer or seed required.

2. Move the spreader to the area where application is to begin.

3. Loosen the plastic wing nut and move it to the desired setting. Retighten the nut.

4. Making sure the flow control lever is in the “OFF” position, fill the hopper, breaking up any lumps.

5. Lower the aerator spikes to the operating position.

6. Start the spreader in motion and then move the flow control lever to the “ON” position as you travel across your lawn. The recommended towing speed is 3 m.p.h.

7. Do not make sharp turns with spikes in the ground

8. Raise aerator spikes to transport position when crossing over concrete or other hard surfaces.

9. Do not aerate if the ground is extremely hard or dry. If ground is too dry, sprinkle or water for one to two hours prior to use.

10. Do not aerate if the ground is too wet (muddy)

8

DRAWING

 

9

 

PARTS# DESCRIPTION

1 Hopper & Side Plat Assembly

2

3

4

5

6

7

8

9

10

Axle & Gear Assembly

Cotter Pin Ø4x30

Screw M5x6

Scratch Board

Flat Washer Ø12

Scratch Board Support Spacer

Big Flat Washer Ø12

Flat Washer Ø20

12

13

Flat Washer Ø16

Axle Spacer

14

15

Fluted Disc Spacer (Short)

Fluted Disc

16 Fluted (Long)

17 Hex M12x90

18 Wheel

19 Hex Nut M12

21 Hex M8x20

22

23

24

Operating Handle

Handle Grip

Hitch Tube

25

26

Hex Bolt M6x65

Nylon Lock Nut M8

29 Pin

30 Hex M8X45

31 Axle & Small Gear Assebmly

33 Hex M8X35

34 Hex M8X40

PARTS LIST

QTY PARTS#

DESCRIPTION

1 35 Nylon Lock Nut M12

1

4

10

2

6

36

37

38

39

40

Spring

Fluted Disc & Fixed Spacer Assy

Small Sprocket Wheel Spacer

Big Sprocket Wheel Spacer

Bushing Chain

42 Ø4

2

2

43

44

Screw M4X12

Hex Bolt M6X30

1 45 Support

10

11

46

47

Hex Bolt M6x30

Big Washer Ø6

1

7

48

49

Nylon Lock Nut M6

Nylon Lock Nut M4

5 50 Connecting

2 51 Nylon

2 52 Threaded

2 53 Cotter Pin Ø3X20

1 54 Connecting

1 55 Spring

1 56 Adjustable Pole

1

2

57

58

Hex Bolt M6x20

Gauge and Lever Assembly

3

9

59

60

Carriage Bolt M6X25

Teeth Washer Ø8

1 61 Bushing

2 62 Wing

1 63 Adjustable

3 64 Handle

1 65 Support Shelves

6 66 Hex

2 67 Fluted Disc Spacer 1 (Short)

   

1

1

1

1

1

1

QTY

2

1

2

1

1

1

1

2

2

1

1

1

9

11

2

1

2

1

1

1

1

1

2

1

1

2

1

10

 

CANNON TOOLS LTD

Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.

Made in China

11