Delta 28-275C User manual
Delta el:Saw 28-275C is a versatile and powerful tool that can be used for a wide variety of woodworking projects. With its 3/4 HP motor, it can handle even the toughest cuts with ease. The el:Saw 28-275C also features a number of safety features, such as a blade guard and anti-kickback pawls, to help keep you safe while you work.
Here are just a few of the things you can do with the Delta el:Saw 28-275C:
- Rip cuts: The el:Saw 28-275C can make precise rip cuts in wood up to 12 inches wide.
- Crosscuts: The el:Saw 28-275C can also make crosscuts in wood up to 6 inches thick.
PDF
Download
Document
Advertisement
Advertisement
I VV UW WLLL Yj Band Saw (Model 28-275C) The Serial No. / Model No. plate is attached to the right side of the base casting. Locate this plate and record the Serial No. and Model No. in your manual for future fererence. SERIAL NO. MODEL NO. DATED 9-11-95 PART NO. 1233105 © Delta International Machinery Corp. 1995 “When it's Delta, “we back №... - — HF you have any problems with “your new Delta Power Tool, - please call us toll free. Have your model and serial numbers ready. | 1-800-GO-DELTA(463-3582) Francais au verso TVNNVIN NOILLONHLSN Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possiblity of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won't make up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop. If a procedure feels dangerous, don't try it. Figure out an alternative procedure that feels safer. REMEMBER: Your personal safety is your responsibility. This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not be modified and/or used forany application otherthan that for which it was designed. If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product. DELTA INTERNATIONAL MACHINERY CORP. MANAGER OF TECHNICAL SERVICES 246 ALPHA DRIVE PITTSBURGH, PENNSYLVANIA 15238 (IN CANADA: 644 IMPERIAL ROAD, GUELPH, ONTARIO N1H 6M7) WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY 1. FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING THE TOOL. Learn the tool's application and limitations as well as the specific hazards peculiar to it. 2. KEEP GUARDS IN PLACE and in working order. 3. ALWAYS WEAR EYE PROTECTION. 4. GROUND ALL TOOLS. If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical receptacle. If an adapter is used to accommodate a two-prong receptacle, the adapter lug must be attached to a known ground. Never remove the third prong. 5. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it “on.” ‚6. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 7. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations, or expose them to rain. Keep work area well-lighted. 8. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area. 9. MAKE WORKSHOP CHILDPROOF - with padlocks, master switches, or by removing starter keys. 10. DON'T FORCE TOOL. it will do the job better and be safer at the rate for which it was designed. 11. USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not designed. 12. WEARPROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or other jewelry to get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. - 13. ALWAYS USE SAFETY GLASSES. Wear safety glasses (must comply with ANSI Z87.1). Everyday eyeglasses only have impact resistant lenses; they are not safety glasses. Also use face or dust mask if cutting operation is dusty. 14. SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and frees both hands to operate tool. 15. DON'T OVERREACH. Keep proper footing and balance at all times. 16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 17. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits, cutters, etc. 18. USERECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by Delta may cause hazards or risk of injury to persons. 19. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in “OFF” position before plugging in power cord. 20. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. 21. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 22. DIRECTION OF FEED. Feed work into a blade or cuttter against the direction of rotation of the blade or cutter only. 23. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't leave tool until it comes to a complete stop. 24. DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol or any medication. 25. MAKE SURE TOOL IS DISCONNECTED FROM POWER SUPPLY while motor is being mounted, connected or reconnected. 26. WARNING: The dust generated by certain woods and wood products can be injurious to your health. Always operate machinery in well ventilated areas and provide for proper dust removal. Use wood dust collection systems whenever possible. ADDITIONAL SAFETY RULES FOR BAND SAWS 1. ADJUST the upper guide about 1/8" above the material being __ cut. 2. MAKE SURE that blade tension and blade tracking are properly adjusted. | 3. STOP the machine before removing scrap pieces from the table. 4. ALWAYS keep hands and fingers away from blade. 5. CHECK for proper blade size and type. 6. DO NOT attempt to saw stock that does not have a fiat surface, unless a suitable support is used. 7. HOLD material firmly and feed into blade at a moderate speed. 8. TURN OFF machine if the material is to be backed out of an uncompleted cut. В 9. MAKE release” cuts before cutting long curves. 10. ADDITIONAL INFORMATION regarding the safe and proper operation ofthis productis available from the National Safety Council, 1121 Spring Lake Drive, ltasca, IL 60143-3201 in the Accident Prevention Manual for Industrial Operations and also in the Safety Data Sheets provided by the NSC. Please also refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations. Carefully unpack the band saw, stand, and all loose items from the cartons. Remove the protective coating from the machined surfaces of the band saw. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose.) After cleaning, cover all unpainted surfaces with a good quality paste wax. ASSEMBLING STAND 1. Assemble the stand as shown in Fig. 2, using the 24 carriage bolts, 8 flat washers, 8 lockwashers and 24 hex nuts. NOTE: When fastening the legs (C) Fig. 2, to the shelf (E), use 8 carriage bolts (F), 8 flat washers, 8 lockwashers and 8 hex nuts. When fastening the tie bars (G) to the legs (C), use 16 carriage bolts (H) and hex nuts. Do not com- pletely tighten the stand hardware at this time. 2. Fig. 3, illustrates the top shelf of the stand. The four holes (A) are for mounting the band saw to the stand. The four holes (B) are for mounting the motor to the stand. If you are using the 62-158 motor, the cord from the motor to the power supply and the cord from the motor to the switch are to be passed through the large hole (D) Fig. 3. FOR ASSEMBLY Your band saw can be assembled using a few basic hand tools including: Screwdriver Phillips screwdriver 7/16" Wrench 1/2" Wrench 9/16" Wrench Hex Key (Allen) Wrench Fig. 2 ASSEMBLING BAND SAW TO STAND The correct holes in the top shelf of the stand for mounting the band saw are shown at (A) Fig. 3. Assemble the band saw to the stand, as shown in Fig. 4, using the four 5/16-18 x 1-3/4" hex head screws, 5/16" flat washers, 5/16" lockwashers and 5/16"-18 hex nuts. The hex nuts and lockwashers will be located on the underside of the top shelf. Push down on top of stand so the legs of stand adjust to the surface of the floor and tighten all stand hardware. ASSEMBLING MOTOR TO STAND The correct holes in the top shelf of the stand for mounting the motor are shown at (B) Fig. 3. Assemble the motorto the stand using four 5/16" x 3/4 inch-long carriage bolts (A) Fig. 5, through the motor plate (B) and stand (C). Fasten the motor to the stand as shown in Fig. 5, from underneath, using four external tooth washers (D), four lockwashers (E) and four hex nuts (F). NOTE: Do not completely tighten the motor to the stand at this time as proper belt tension and pulley alignment must first be made. Place grommet (G) in large hole in top shelf as shown in Fig. 6. IMPORTANT: If you are using the 62-158, 3/4 H.P. motor, insert switch cord and power cord through hole as shown in Fig. 6. ASSEMBLING SWITCH If you purchased the 62-158, 3/4 H.P. motor, you received a switch and cord set connected to the motor. Assemble the switch to the stand as follows: 1. IMPORTANT: When assembling the switch to the stand, MAKE SURE the motor power cord is NOT connected to the power source. 2. Remove the outer hex nut (A) Fig. 7, from the switch stem. Leave external tooth lockwasher (B) and inside hex nut (C) on switch stem. CAUTION: The proper grounding of the switch to prevent shock hazard, depends on the use of the external tooth lockwasher in the manner shown. Fig. 5 Fig. 7 in the down position. 4. Place the switch bracket (D) Fig. 8, on switch stem with key of switch bracket engaged with keyway in switch stem. Fasten switch in place with hex nut (A) that was removed in STEP 2. NOTE: The excess wire from the motor to the switch should be wrapped and tied and then positioned out of the way. | 5. IMPORTANT: It is recommended that when the band saw is not in use, the switch be locked in the “OFF” position using a padlock. Catalog No. 49-031 Padlock is available as an accessory. ASSEMBLING BELT GUARD, MOTOR AND ARBOR PULLEYS, AND DRIVE BELT 1. Thread the six self-tapping screws (A) Fig. 9, about halfway into the six holes provided in the ledge of the inside belt and pulley guard (B) as shown. 2. Assemble the inside belt and pulley guard (B) Fig. 10, over the arbor and motor shafts as shown and fasten the guard to the machine using the two 1/2 inch-long hex head cap screws and flat washers (C). NOTE: Do not com- pletely tighten the screws at this time. 3. Place the spacer (D) Fig. 11, into the countersunk hole (E) located behind the belt and pulley guard (B). Then insert the 2-3/4 inch hex head cap screw with flat washer (F) into the center hole (GQ), through the spacer (D) and threaditinto the tapped hole (E). 4. NOTE: Make certain tne arpor snait (rj riy. ig, anu motor shaft (J) are centered in the holes of the belt and pulley guard (B) as shown, then tighten screws (C) and (F). 5. Assemble the arbor pulley (K) Fig. 13, to arbor shaft with hub of pulley in the “out” position. Insert key (L) in keyway of arbor shaft and tighten set screw (M). 6. Assemble motor pulley (N) Fig. 14, to motor shaft with hub of pulley in the “in” position. Insert key (P) in keyway of motor shaft and tighten set screw (R) in motor pulley 7. Assemble drive belt (S) Fig. 15, to the arbor puiley and motor pulley as shown. Using a straight edge, check to see if the arbor pulley (K) and the motor pulley (N) are aligned. If an adjustment is necessary, both pulleys can be moved in or out to obtain proper alignment. Adjust for proper belt tension by moving the motor in or out by loosening four mounting bolts, two of which are shown at (T). Correct beit tension is obtained when there is approximately 1/2 inch deflection at the center span of the belt (S) Fig. 15, using light finger pressure. NOTE: When proper belt tension is obtained and both pulleys are aligned, make certain to tighten all mounting hardware. 8. Assemble outer belt and pulley guard (V) to the inside belt and pulley guard and tighten the six screws, three of which are shown at (A) Fig. 16. Fig.16 POWER CONNECTIONS A separate electrical circuit should be used for your power tools. This circuit should not be less than #12 wire and should be protected with a 15 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and 3-pole receptacles which accept the tools plug. For distances up to 100 feet use #12 wire. For distances up to 150 feet use #10 wire. Before connecting the motor to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as stamped on motor nameplate. All line connections should make good contact. Running on low voltage will injure the motor. Have a registered electrician replace or repair damaged or worn cords immediately. GROUNDING INSTRUCTIONS CAUTION: This tool must be grounded while in use, to protect the operator from electric shock. The motor is shipped wired for 115 Volt, Single Phase and is equipped with an approved 3-conductor cord and 3-prong grounding type plug to fit the proper grounding type receptacle, as shown in Fig. 17. The green conductor in the cord is the grounding wire. CAUTION: Never connect the green wire to a live terminal. An adapter, shown in Fig. 18, is available for connecting 3-prong grounding type plugs to 2-prong receptacles. THIS ADAPTER IS NOT APPLICABLE IN CANADA. The green-colored rigid ear, lug, etc., extending from the adapter is the grounding means and must be connected to a permanent ground such as to a properly grounded outlet box, as shown in Fig. 18. CAUTION; IN ALL CASES, MAKE SURE THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A CERTIFIED ELECTRICIAN CHECK THE RECEPTACLE. DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS. GROUNDED OUTLET BOX— GROUNDED OUTLET BOX AN : CURRENT GROUNDING MEANS | CARRYING | PRONGS uu ADAPTER — | O GROUNDING BLADE IS 2 u LONGEST OF THE 3 BLADES Fig. 17 Fig. 18 © TABLE INSERT Place table insert (A) Fig. 19, in the hole provided in the table, making sure the pin (B) in the table engages one of the indents in the table insert. ward if E Om EEE UU Ш я ие EE Es Es The table on your band saw can be tilted 45 degrees to the right and 10 degrees to the left. To tilt the table, loosen the two knobs (A) Fig. 20; tilt the table to the desired angle and tighten the two knobs (A). ADJUSTING TABLE STOP The band saw is equipped with an adjustable table stop (A) Fig. 21, that allows the table to be set perfectly at 90 degrees with the blade. Tilt the table to the left until the table stop (A) Fig. 21, contacts the bottom of the table. Place a square on the table and against the blade as shown in Fig. 22, and check to see if the blade is 90 degrees to the table surface. If an adjustment is necessary, proceed as follows: 1. Tilt the table slightly to the right and tighten table lock knobs. 2. Turn adjustment nut (B) Fig. 21, right or left as neces- sary to raise or lower table stop (A). IMPORTANT: Certain models of band saws will have an additional locknut assembled to the end of the table stop (A) Fig. 21, directly under casting (C). Loosen locknut and turn adjustment nut (B) right orleftas neededto raise or lower the table stop (A). Tighten locknut after adjustment is made. 3. Lower the table and make certain the table is 90 degrees to the blade as shown in Fig. 22. 4. ltis necessary to remove the adjustable table stop (A) Fig. 21, when tilting the table to the left. BLADE TENSION On the back of the upper wheel slide bracket there is a series of graduations. These indicate the proper tension for various widths of blades. With the blade on the wheels, turn the knob (A) Fig. 23, to raise or lower the wheel, until the red fiber washer (B) is in line with the proper graduation for the size of blade being used. The graduations will be found correct for average work, and are not affected by rebrazing of the saw blade. We urge you to use these graduations until you have become familiar enough with the operation of the Band Saw to vary the tension for different kinds of blades or work. Over-straining is a common cause of blade breakage and other unsatis- factory blade performance. Release the tension when the machine is not in use. TRACKING THE BLADE IMPORTANT: Before tracking the blade, make sure the blade guides and blade support bearings are clear of the blade so as not to interfere with the tracking adjustment. After tension has been applied to the blade, turn the wheels slowly forward by hand and watch the blade (A) Fig. 24, to see that it travels in the center of the upper tire. If the blade begins to creep toward the front edge, loosen the wing nut (B) Fig. 25, and tighten the thumb screw (C). This will tilt the top of the wheel toward the back of the machine and will draw the blade toward the center of the tire. If the blade creeps toward the back edge, turn the thumb screw in the opposite direction. Fig. 25 a ea ES та es LE AT ER fe es Bry ту rh E Adjust the thumb screw (C) Fig. 25, only a fraction of a turn at a time. NEVER TRACK THE BLADE WHILE THE MACHINE IS RUNNING. After the blade is tracking in the center of the tires, tighten the wing nut (B) Fig. 25. ADJUSTING UPPER BLADE GUIDE ASSEMBLY The upper blade guide assembly (A) Fig. 26, should always be set as close as possible to the top surface of the material being cut by loosening lock knob (B) and moving the guide assembly (A) to the desired position. The upper blade guide assembly should also be adjusted so that the blade guides (A) Fig. 27, are flat with the blade. If an adjustment is necessary, loosen screw (B) and rotate the complete guide assembly (C) until the blade guides are flat with the blade. 10 Не, rares Ly UPPER BLADE GUIDES AND BLADE SUPPORT BEARING The upper blade guides and blade support bearings are adjusted only after the blade is tensioned and tracking properly. To adjust proceed as follows: 1. The upper blade guides (A) Fig. 28, are held in place by means of the set screws (B). Loosen the set screws (B) to move the guides (A) as close as possible to the side of the blade, being careful not to pinch the blade. Then tighten the screws (B). 2. The guides (A) Fig. 28, should then be adjusted so that the front edge of the guides is just behind the “gullets” of the saw teeth. The complete guide block bracket canbe moved in or out by loosening thumb screw (C) and turning knurled knob (D) Fig. 28. When guides (A) are set properly, tighten thumb screw (С). 3. The upper blade support bearing (E) Fig. 28, prevents the blade from being pushed too far to the back which could damage the set in the saw teeth. The support bearing (E) should be set 1/64" behind the blade by loosening thumb screw (F) and turning knurled knob (G) to move the support bearing (E) in or out. 4. The blade support bearing (E) should also be adjusted so the back edge of the blade overlaps the outside diameter of the ball bearing by about 1/16". The bearing (E) is set on an eccentric and to change position remove screw (H) and bearing (E) Fig. 28. Loosen thumb screw (F), back out screw (G) and reposition shaft that bearing (E) is attached to. ADJUSTING LOWER BLADE GUIDES AND BLADE SUPPORT BEARING The lower blade guides and blade support bearing should be adjusted at the same time as the upper guides and bearing as follows: 1. Loosen the two screws (A) Fig. 29, and move the guides (B) as close as possible to the side of the blade, being careful notto pinch the blade. Then tighten screws (A). 2. The front edge of the guide blocks (B) should be adjusted so they are just behind the “gullets” of the saw teeth by turning the knurled knob (C) Fig. 29. 3. Thelowerblade support bearing (D) Fig. 29, should be adjusted so it is about 1/64" behind the back of the blade by turning the knurled knob (E). 11 VE FRE VV VV La UL boa WN? To change blades, proceed as follows: 1. Open the upper and lower wheel guards. 2. Release tension on the band saw blade. 3. Remove the table adjustment pin and table insert. 4. Slip the blade off the wheel and guide it out through the slot in the table. 5. To install a new blade, reverse the above procedure. BAND SAW BLADES A band saw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain long use from a band saw blade if you give it fair treatment. Be sure you use blades of the proper thickness, width and temper for the various types of material to be cut. Always use the widest blade possible. Use the narrow blades only for sawing small, abrupt curves and for fine delicate work. This will save blades and will produce better work. Band saw blades may be purchased, welded, setand sharpened ready for use. For cutting wood and similar materials Delta can supply blades in widths of 1/8, 3/16, 1/4, 3/8, 1/2 and 3/4 inches. File and set the wood cutting blades whenever you find it requires pressure to make them cut. If a blade is broken it can be brazed or welded; however, if it has become badly work-hardened it will soon break in another place. If you are not equipped to file, set and braze or weld blades, take them to a saw filer for reconditioning. Any one of a number of conditions may cause a band saw blade to break. Blade breakage is, in some cases, unavoid- able, being the natural result of the peculiar stresses to which such blades are subjected. It is, however, often due to avoidable causes, most often to lack of care or judgment on the part of the operator in mounting or adjusting the blade or guides. The most common causes of blade break- age are: (1) faulty alignments and adjustments of the guides, (2) forcing or twisting a wide blade around a curve of short radius, (3) feeding too fast, (4) dullness of the teeth or absence of sufficient set, (5) excessive tightening of the blade, (6) top guide set too high above the work being cut, (7) using a blade with a lumpy or improperly finished braze or weld and, (8) continuous running of the saw blade when not in use for cutting. New blades for the standard 14 inch Band Saw are 93-1/2 inches long. The adjustment will accommodate blades up to a maximum length of 94 inches and to a minimum length of 91-1/2 inches. When equipped with the No. 28-984 Height Attachment, new blades should be 105 inches long; maximum and minimum lengths are 106 and 103-1/2 inches. 12 wo iri EEE UA FI Ds TUI ISA NY Before starting the machine, see that all adjustments are properly made and the guards are in place. Turn the pulley by hand to make sure that everything is correct BEFORE turning on the power. Keep the top guide down close to the work at all times. Do not force the material against the blade too hard. Light contact with the blade will permit easier following of the line and prevent undue friction, heating and work-hardening of the blade at its back edge. KEEP THE SAW BLADE SHARP and you will find that very little forward pressure is required for average cutting. Move the stock against the blade steadily and no faster than will give an easy cutting movement. Avoid twisting the blade by trying to turn sharp corners. Remember, you must saw around corners. CUTTING CURVES When cutting curves, turn the stock carefully so that the blade may follow without being twisted. If a curve is so abrupt that it is necessary to repeatedly back up and cut a new kerf, either a narrow blade is needed or a blade with more set is required. The more set a blade has, the easier it will allow the stock to be turned, but the cut is usually rougher than where a medium amount of set is used. In withdrawing the piece being cut, in order to change the cut, or for any other reason, the operator must be careful that he does not accidentally draw the blade off the wheels. In most cases itis easier and safer to turn the stock and saw out through the waste material, rather than try to withdraw the stock from the blade. DELTA SERVICE CENTRES CENTRES DE _ SERVICE APRES- VENTE DE L'USINE DELTA ALBERTA Bay #6, 2520-23 St. N.E. Calgary, Alberta T2E 8L2 TEL: (403) 735-6166 FAX: (403) 735-6144 BRITISH COLUMBIA 8520 Baxter Place Burnaby, B.C. V5A 418 TEL: (604) 420-0102 FAX: (604) 420-3522 MANITOBA 1699 Dublin Avenue Winnipeg, Manitoba R3H OH? TEL: (204) 633-9259 FAX: (204) 632-1976 ONTARIO 644 Imperial Road Guelph, Ontario N1H 6M7 TEL: (519) 836-2840 FAX: (519) 836-9352 Mobile Service QUÉBEC . 1447, Bégin St-Laurent, (Mtl), P.Q. H4R 1V8 TEL: (514) 336-8772 FAX: (514) 336-3505 Suite 202 2022, rue Lavoisier Ste-Foy, P.Q. GIN 4L5 TÉL: (418) 681-7305 FAX: (418) 681-1695 HEAD OFFICE SIEGE SOCIAL Delta international Machinery P.O. Box 848 644 Imperial Road Guelph, Ontario NiH 6M7 TEL: (519) 836-2840 FAX: (519) 836-9352 Centres de service aprés-vente agréés Delta (Porter-Cable) du Canada ALBERTA Edmonton, Alberta -. Can-Tech Tool Service 9252-34A Avenue T6E 5P4 (403) 450-6389 Edmonton, Alberta O.K. Power Tool Repair Ltd. 14740-115 Avenue T5M 3B9 (403) 455-0373 Grand Prairie, Alberta Ber-Mar Rewind 9609-109th Street T8V 4E3 (403) 532-0818 Lethbridge, Alberta Central Electric Ltd. 124 N Mayor Magrath Drive TiH 3P4 (403) 327-5995 Medicine Hat, Alberta Randy's Refrigeration Ltd. 694 South Railway St., S.E. T1A 2W1 (403) 526-0463 Red Deer, Alberta McAuley Electric Motor Ltd. 5301-50th Avenue T4N 486 (403) 346-3361 BRITISH COLUMBIA Abbotsford, B.C. Abbotsford Toot Centre 33723 À. King Road \/25 4№ (604} 859-9023 Campbell River, B.C. Andrews Lawnmower Service Lid. 80 Westgate Road VOW 1R2 (604) 923-7122 Castlegar, B.C. Martech Electrical Systems Ltd. 1700 Woodland Drive P.O. Box 3403 ViN 3N8 (604) 365-2115 Courtenay, B.C. Andrews Lawnmower Service Ltd. 883 McPhee Avenue VON 3A1 (604) 334-4439 Cranbrook, B.C. Sarc Repair Ltd. 16 13th Avenue S. V1C 2R7 (604) 426-6333 Kamloops, B.C. Thompson Vailey Rewind 1647 Valleyview Dr. V2C 4B6 (604) 374-1633 Kelowna, B.C. Central Electric Motor Rewind Ltd. #1-1960 Windsor Road V1Y 4R5 (604) 860-4415 Langley, 8.C. A.C. Power Toot Clinic Ltd. #105 19835 56th Ave. V3A 3X8 (604) 530-3550 Nanaimo, B.C. Solar Electric Repairs Lid. 20 A Cliff Street VOR 5E5 (604) 753-1731 Penticton, B.C. A.C. Motor Electric Ltd. 259 East Okanagan Avenue V2A 3J8 (604) 493-1440 Prince George, B.C. Accurate Tool & Repair 3660-18th Avenue V2N 1A9 (604) 562-8833 Surrey, B.C. Delta Tool Repair Ltd. #2 7533-135th Street V3W ONG (604) 591-3230 Vernon, B.C. E.E. Electrical Enterprises Ltd. 4600 31st Street V1T 5J9 (604) 542-1166 Victoria, B.C. A.B.C. Electric Limited 831 Yates Street VBW 1M1 (604) 382-7221 Victoria, B.C. Troy Electrical Repairs Unit #1, 3131 Delta St. V8Z 1A6 (604) 382-7442 MANITOBA Brandon, Manitoba Harold's Electric Service 362 Pacific Avenue R7A 0H5 (204) 727-7292 Steinbach, Manitoba Palmlite Electric Motors Box 3308 ROA 2A0 (204) 326-9271 Thompson, Manitoba KNC Etectric Ltd. P.O. Box 428 R8N 1N2 (204) 778-7333 N.W.T. Yellowknife, NWT Polar Tech 12 Balsillie Crt. X1A 3H8 (403) 873-8324 NEW BRUNSWICK Bathurst, N.B. Roger's Electric Motor Service 1561 Miramichi Avenue E2A 3Y4 (506) 548-8711 Edmundston, N.B. Edmundston Electric Motor Service Lid. 6 Lacombe Street E3V 3K3 (506) 735-4485 Fredericton, N.B. Electric Motor Service 129 Westmoriand St. ЕЗВ 314 (506) 458-8770 Riverview, N.B. Doug's Tool Repair 43 Allan Street E1B 483 (506) 386-3366 Saint John, N.B. A.B. McLean € Company Ltd. 116 Victoria Street E2K 1L6 (506) 634-8184 Saint John, N.B. Eastern Distributors Limited 38 Bayside Drive E2J 1A2 (506) 634-8314 NEWFQUNDI AND Cornerbrook, NFLD Rideout Tool & Supply 115 Humber Road А2Н 1G1 (709) 634-3294 Gander, NFLD Domestic Service Centre Box 83 43 McCurdy Dr. A1V1W5 (709) 256-7738 St. John's NFLD Rideout Tool & Supply Ltd. 222 Kenmount Road A1B 3R2 (709) 754-2240 Shoul Harbour, NFLD Greening's Electrical Maintenance Limited P.O. Box 174 AOC 2L0 (709) 466-6606 NOVA SCOTIA Dartmouth, N.S. Electric Motor Shop Ltd. 673 Main Street B2W 3T6 (902) 463-8165 Dartmouth, N.S. Fader Industries 83 Shore Road ВЗА 1А5 (902) 466-2333 Halifax, N.S. Village Power Shop Ltd. 2756 Gladstone St. B3K 4W5 (902) 455-0208 Sydney, N.S. Dale Burke Auto Electric 1081 Upper Prince St. В1Р 5P5 (902) 564-4337 Truro, N.S. Smith Motor & Pump 333 Industrial Avenue B2N 4A7 - (902) 893-7291 ONTARIO Ajax, Ontario J.D. Air & Electric U3-676 Monarch Ave. LiS 452 (905) 427-2595 Bancroft, Ontario Bancroft Electric Motors Box 1763 KOL 1C0 (613) 332-4705 Barrie, Ontario Master Sales & Service 16 Mulcaster Street L4M 3M1 (705) 726-7102 Belleville, Ontario Emsco Ltd. 57 Cannifton Road K8N 4V1 (613) 966-3234 Brantford, Ontario Gilbert-McEachern Electric Ltd. 225 Drummond St. N35 6B3 (519) 753-0465 Burlington, Ontario Bayshore Tool & Equipment 2312 Industrial Street L7P 1A1 (905) 332-0554 Cambridge, Ontario Speedy Tool Repair Box 21102, Holiday Postal Outlet N3C 481 (519) 624-0122 Chatham, Ontario Ron's Sales & Service 208 Queen Street N7M 2H1 (519) 351-8331 Cornwall, Ontario Power Tool Service 423 Fourth Street, W. Кб.) 257 (613) 938-1292 Downsview, Ontario After Sales Repair Service 167 Limestone Cresc. M3J 2R1 (416) 663-8858 Englehard, Ontario Spruce Grove Pumps R.R. #2 POJ 1H0 (705) 544-8254 Etobicoke, Ontario Karl's Power Tools Sales and Service 25-22 Goodmark Place MOW 6R2 (416) 675-1310 Hamilton, Ontario Active Tool Repair 800 Barton St. E. #2 L8L 3B3 (905) 545-7646 Hamilton, Ontario Apollo Tool Repair & Sales Ltd. 180 Parkdale Ave. N. L8H 5X2 (905) 544-5202 Hanover, Ontario Wayne's Electric Ltd. 626-12th Avenue NAN 2V5 (519) 364-4020 Huntsville, Ontario Huntsville Armature 51 Ferguson Road RR 1 POA 1KO (705) 789-9301 Kingston, Ontario Boyd Electric Co. Ltd. 833 Portsmouth Ave. K7M 1W6 (613) 548-4888 Kitchener, Ontario RMW Electric 969 Guelph Street N2H 522 (519) 744-1821 London, Ontario Moore Tool & Motor Service 960 Elias St, Unit 2 N5W 3P4 (519) 679-6326 Milton, Ontario Sure-Cut Industries Ltd. 925 Main St, E. Units 2 & 3 LOT 4H8 (905) 878-8790 Mississauga, Ontario Bertsch Power Tool Service Ltd. 1320 Midway Blvd. Unit 18 L5T 2K4 (905) 670-7716 (continued) (suite a la page suivante) Centres de service apres-vente agréés Delta (Porter-Cable) du Canada - Suite Niagara Falls, Ontario Power Tool Repair Centre 4661 Queen Street L2E 2L9 (905) 357-4333 North Bay, Ontario Gateway Electric 1570 Main Street West P1B 2X3 (705) 476-5814 Oakville, Ontario Industrial Tool Repair Centre 2140 Speers Road L6L 2X8 (905) 827-5444 Orillia, Ontario Orser Electric 1995 Ltd. 301 Forest Avenue L3V 6K7 (705) 326-6427 Ottawa, Ontario Emie’s Electric Lid. 1732 Woodward Dr. K2C OP8 (613) 228-9480 Owen Sound, Ontario Murray's Saw & Knife Service 1351 2nd Avenue East N4K 2J5 (519) 376-2495 Peterborough, Ontario Dependable Electric Motor Service 861 Webber Avenue K9J 5X9 (705) 742-0732 Richmond Hill, Ontario Dubiner Industries Limited 40 West Pearce St. #2 L4B 1C5 (905) 771-6111 St. Catharines, Ontario Kaupp Electric 225 Merritt Street L2T 1J7 (905) 227-1661 Sarnia, Ontario Serv-a-Tool and Repairs Ltd. 866 Philip Street N7T 1Z6 (519) 344-8837 Sault Ste. Marie, Ontario Sabre Sharpening Centre 677 MacDonald Ave. Unit 11 P6B 1J4 (705) 254-3711 Scarborough, Ontario George Power Tools Service 1365 Morningside Ave. Unit 11 M1B 3C5 (416) 286-3933 (416) 286-3934 South Porcupine, Ontario Porcupine Air & Electric Tool Repairs 51 Smith Street PON 1HO (705) 235-8950 Stratford, Ontario Culliton Brothers Ltd. 473 Douro Street N5A 6W3 (519) 271-1981 Sudbury, Ontario Northern Auto Scope U2-122 Douglas St. West, Bag 5010 P3A 452 (705) 673-8148 Sudbury, Ontario Sudbury Service Ctr. 83 Lome St., S. P3C 4P2 (705) 673-5085 Thunder Bay, Ontario Mahon Electric Co. Ltd. 340 Waterloo Street P.O. Box 307, Sin. “F” P7C 4V9 (807) 623-8471 Tilsonburg, Ontario Merv Davis Electric 346 Simcoe Street N4G 2J8 (519) 842-7194 Toronto, Ontario AMT Power Tool & Saw Lid. 1182 Castlefield Ave. M6B 1G1 (416) 783-6095 Toronto, Ontario Miller Air & Electric Tool Co. 7 Gilead Place MSA 3C8 (416) 368-5646 Windsor, Ontario Monelco Motors Ltd. 333 Eugenie St., E. N8X 2Y? (519) 969-9660 PRINCE EDWARD ISLAND Charlottetown, P.E.Í. Chandler Motor Repair 70 Kensington Road C1A 5J2 (902) 892-6345 QUÉBEC Alma, Lac St. Jean, P.Q. Outillage Moteur Electrique Alma 228 Boul. Dequen Nord G8B 5N5 (418) 668-2022 Aylmer, P.Q. Jacques Leblanc Mobile Service 50 Terrace Crescent JOH 2N3 (613) 720-6040 Beloeil, P.Q. Placide Mathieu & Fils Inc. 670 rue Picard J3G 5X9 (514) 467-3565 Chicoutimi (Nord), P.Q. J. Sirois Electrique inc. 2203 rue Roussel G7G 1W4 (418) 543-3308 Crabtree, Quebec Les Services D.E.R. Enr. 335 Ch. Ste. Marie JOK 1B0 (514) 754-2895 Dolbeau, P.Q. Moteur Electrique Conroy Ltée 1849 bout. Wallberg G8T 1J1 (418) 276-6596 Dollard Des Ormeaux, Entreprise Clem Herscheid Inc. 4307 St. John Blvd. H9H 2A4 (514) 626-1683 Drummondville, P.Q. Docteur de l’Outil Melam Enr 200A Rue Dorion J2C 179 (819) 478-1109 Gaspé, P.Q. SOS Electric Ménager Enr. 23 Adams GOC 1R0 (418) 368-1779 Gatineau, P.Q. Equip. Brabant & Fils. 776 Boul. Maloney Est. J8P 1G6 (819) 663-2463 Granby, P.Q. Armature Shefford Inc. 200 rue Cartier J2G 5A6 (514) 375-1414 Grand Mère, P.Q. Général Surplus 320 - 12 rue GST 4A5 (819) 538-6383 Greenfield Park, P.Q. Service D'Outils ACM 5 Morley Suite 114A J4V 2Y8 (514) 466-1173 Jonquière, P.Q. Moteur Saguenay Enr. 2885 boul. du Royaume G7S 4K6 (418) 548-7161 Lavai, P.Q. S. Brodaric 4103 MacKenzie Court H7W 3C9 (514) 688-9399 Laval, P.Q. Service D'Outils F.G.L. Inc. 1617 Autoroute 440 O. H7L 3W3 (514) 682-7979 Louiseville, P.Q. Outillage Lam-Ré Inc. 61 rue St-Aimé J5V 2A9 (819) 228-8444 Mont-Laurier, P.Q. Atelier Ge-Ma Enr. 395 rue Dupont JIL 2R6 (819) 623-6622 Montmagny, P.Q. Réparation Electrique 170 4e Rue G5V 3L5 (418) 248-2072 Montréal, P.Q. Laflamme Electrique 1569 rue Amherst H2L 3L5 (514) 527-9151 Rimouski, P.Q. Dickner Inc. 559 rue Lausanne G5L 7C9 (418) 723-7936 Riviere Du-Loup, P.Q. Dickner Inc. 370 Le Miscouala G5R 272 (418) 867-1824 Rouyn-Noranda, P.Q. Equipment TNO Inc. 1250 Boul Saguenay PO 2157 JOX 5A6 (819) 764-3221 St. David-Ste-Lévis, P.Q. Larivière Moteur Electrique 4895 Boul. de la rive sud G6W 1H3 (418) 837-7982 St-Hyacinthe, P.Q. Centre De Service St. Hyacinthe Enr. 3400 Laframboise J2S 474 (514) 774-7728 St. Jean, P.Q. Landry Repare tout inc. 825 St. Jacques J3B 2N2 (514) 346-2005 St. Jérôme, P.Q. Centre d'électrique Jérómien Inc. 712 St. Georges J7Z 506 (514) 430-2676 St. Joseph De Sorel, P.Q. Electro-Moteur Richelieu 602 St. Pierre Street J3R 1A8 (514) 742-0203 Ste-Agathe, P.Q. Electro G.C. Enr. 60 St-Vincent J8C 2A6 (819) 326-4851 Sept-lles, P.Q. Centre de Location Sept-lles 1175 Boul. Laure G4S 181 (418) 962-4230 Sherbrooke, P.Q. Atelier d'Outils Electriques Enr. 991 King Ouest J1H 153 (819) 567-1775 Trois-Rivières, P.Q. Outils Mauriciens Inc. 2444 bivd. Des Récollets G8Z 3X7 (819) 373-1024 Val D’or, P.Q. Hytex 85 Inc. 1710 3° Avenue JOP 1W2 (819) 825-1475 Valleyfield, P.Q. Centre de Réparation Valleyfield Inc. 151 rue Maden JES 3V5 (514) 373-6055 Victoriaville, P.Q. Baril Electrique Inc. 444 Cantin G6R 7E6 (819) 752-4480 Ville St-Gabriel, P.Q. Beaulieu Electrique Ltée 130 rue Dequoy JOK 2N0 (514) 835-4781 A SASKATCHEWAN Lloydminster, Sask. Dzus Motor Repair 4201 52nd Street S9V OY9 (306) 825-7337 N. Battleford, Sask. Ray's Electric Motor Rebuilders 11152 8th Avenue SOA 2N4 (306) 445-1611 Prince Albert, Sask. P.A. Electric Service 129 16th Street W. Sev 3v2 (306) 764-4236 Regina, Sask. United Motor Electric 1234 Scarth Street S4R 2E5 (306) 352-9744 Saskatoon, Sask. K & J Repair #3 1622 Ontario Ave. S7K 158 (306) 244-1164 Swift Current, Sask. United Motor Electric Ltd. 141 8th Avenue N.W. S9H 0Z5 (306) 773-2058 Yorkton, Sask. Bonsal’s Appliance Repair Ltd. 76-7th Avenue South S3N 2V7 (306) 783-8991 YUKON Whitehorse, Yukon Oscar's Electric Co. Lid. 310 Alexander Street Y1A 2L6 (403) 667-2330 DELTA 09/5/95 AA 14 AA DELTA PORTER+CABLE DELTA/PORTER-CABLE GUARANTEE Delta is proud of the quality power tools it sells. The component parts of our tools are inspected at various stages of production and each finished tool is subjected to a final check before being packaged for shipment. Because of our confidence in our engineering quality, Delta agrees to repair or replace any part or parts of Delta/Porter-Cable Power Tools and accessories which examination proves to be defective in workmanship or material. The warranty period for Delta brand is two years, for Porter-Cable, one year. Any alleged defective part or parts must be returned prepaid to the Delta factory or one of the service centres. The guarantee does not include repair labour or parts replacement required because of misuse, abuse, or normal wear and tear. Repairs made by other than our factory, Delta service centre or authorized service station relieve Delta of further liability under this guarantee. THIS GUARANTEE 1S MADE EXPRESSLY IN PLACE OF ALLOTHER GUARANTEES OR WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO QUALITY, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. GARANTIE DELTA/PORTER-CABLE Delta est fière de la qualité des outils électriques qu'elle met sur le marché. Leurs composants sontinspectés à chaque étape de la fabrication, et chaque outil subit une dernière vérification avant d'être emballé pour l'envoi. Pour confirmer l’entière confiance de Delta dans la qualité technique de ses produits, la compagnie s'engage à réparer ou à remplacer tout élément ou accessoire d'un outil électrique Delta/Porter-Cable présentant un défaut dûment reconnu de matière ou de fabrication. La garantie est d’une durée de deux (2) ans pour les articles de la marque Delta et d'un an pour les Porter-Cable. La ou les pièces présumées défectueuses doivent être renvoyées franco de port à l'usine ou à l'un des centres de service de l’usine Delta. La garantie ne comprend pas les frais de main-d'oeuvre ou de remplacement, de pièce, occasionnés par suite de mauvais usage, dégradation et usure normale, lesquels ne donnent droit ni à remplacement, ni à réparation. Toute réparation effectuée en dehors de notre usine, de nos succursales de service et de nos centres de service autorisés annule ta garantie. IL EST EXPRESSEMENT PRECISE QUE NOUS NE SERONS ENGAGES PAR AUCUNE AUTRE GARANTIE (EXPRESSE OU TACITE) DE QUALITÉ INTRINSÈQUE, DE QUALITÉ MARCHANDE OU D'APTITUDE À UN EMPLOI PARTICULIER. Printed in USA Imprimé aux E-U. 16 ">

Public link updated
The public link to your chat has been updated.
Advertisement