Sony KLV-32S550A User manual

PDF

Dokument

Reklaam

KLV-37S550A

KLV-32S550A

KLV-32S530A

KLV-26S550A

LCD Colour TV

Operating Instructions

4-130-985-13(1)

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Introduction

Thank you for choosing this Sony product.

Before operating the TV, please read this manual thoroughly and retain it for future reference.

The illustrations used in this manual are of the

KLV-32S550A unless otherwise stated.

Trademark information

• HDMI, the HDMI logo and High-Definition

Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

• “BRAVIA” and are trademarks of Sony

Corporation.

Notes for Australia and New Zealand model

This product is ENERGY RATING qualified in the

“Home” mode. ENERGY RATING is a programme designed to promote energy efficient products and practices.

• When the TV is initially set up, it is designed to meet ENERGY RATING requirements while maintaining optimum picture quality.

• Changes to certain features, settings and functionalities of this TV (e.g. Picture/Sound and

Eco settings) can slightly change the power consumption.

Depending upon such changed settings, the power consumption may vary which possibly could exceed the stated energy rating. To reset the TV to ENERGY

RATING qualified settings, select “Home” mode from the initial set-up procedure in “Factory Settings” under the “Set-up” menu.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

D:\Chin Meng's job\SONY-LCD\SY0204_R1 (Rev-

3)\4130985131_GB\030STU.fm

masterpage:Left

Start-up Guide

Checking the accessories

Stand (1) and screws (4)

Remote RM-GA016 (1)

Size AA batteries (R6 type) (2)

To insert batteries into the remote

Push and lift the cover to open.

2: Connecting an antenna/ cable/VCR

Connecting an antenna/cable

TV, CATV,

Satellite or

If cannot receive FM signal

Antenna selector

FM signal

TV signal

Antenna cable

(not supplied)

1: Attaching the stand

B KLV-37S550A

B KLV-32S550A/KLV-32S530A/KLV-26S550A

Connecting an antenna/cable and VCR

Antenna cable

(not supplied)

• This TV is very heavy, so two or more people should place the TV onto the stand.

• If using an electric screwdriver, set the tightening torque at approximately 1.5N·m (15kgf·cm).

• Ensure the AC power cord is away from screw holes during stand installation to avoid damage to the AC power cord.

Audio/Video cable (not supplied)

VCR

Antenna cable

(not supplied)

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

3: Preventing the TV from toppling over

4: Bundling the cables

For KLV-37S550A: For KLV-32S550A/

KLV-32S530A/

KLV-26S550A:

• Do not bundle the AC power cord together with other cables.

5: Performing the initial set-up

3, 4, 5, 6, 9

Install a wood screw (4 mm in diameter, not supplied) in the TV stand.

Install a machine screw (M4 × 14, not supplied) into the screw hole of the TV.

For KLV-32S550A/KLV-32S530A/

KLV-26S550A:

Attach a nut (M4, not supplied) from the bottom of the Table-Top Stand to the screw securely.

Tie the wood screw and the machine screw with a strong cord.

• An optional Sony support belt kit is used to secure the

TV. Contact your nearest Sony Service Centre to purchase a kit. Have your TV model name ready for reference.

8 Connect the TV to your AC power outlet

(110-240 V AC, 50/60 Hz) (New Zealand and Tunisia only: 220-240 V AC, 50/60 Hz).

Press 1 on the TV.

When the TV is in standby mode (the 1 (standby) indicator on the TV front panel is red), press "/1 on the remote to turn on the TV.

When you turn on the TV for the first time, the

“Language” menu appears on the screen.

Selecting the language, country/ region and location

Follow the instructions on the screen.

Press

/

to select the language displayed on the menu screens, then press .

Press

/

to select the country/region, then press .

Press

/

to select “Home”, then press .

Continued

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Auto-tuning the TV

Press

/

to select “OK”, then press .

The TV starts searching for all available channels.

If a message appears for you to confirm the antenna connection

No programmes found. Please connect antenna

(aerial) and select “Confirm” to start auto-tuning again. If 200 channels are found, auto-tuning is stopped.

When the “Programme Sorting” menu appears on the screen, follow the steps of

“Programme Sorting” (page 21).

If you do not want to change the order in which the channels are stored on the TV, go to step 8.

Press MENU to exit.

The TV has now tuned in all the available channels.

Press

/

to select the desired setting in

“Display this menu next time?” dialogue, then press to exit.

• If “Yes” is selected and the TV is turned off by pressing 1 on the TV, or is disconnected from the

AC power outlet, the initial set-up procedure restarts the next time the TV is turned on.

Watching TV

Press 1 on the TV to turn on the TV.

Press the number buttons or PROG +/– to select a TV channel.

Press 2 +/– to adjust the volume.

Detaching the Table-Top

Stand from the TV

• Do not remove the Table-Top Stand for any reason other than to wall-mount the TV.

B KLV-37S550A

B KLV-32S550A/KLV-32S530A/KLV-26S550A

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Safety information

Installation/Set-up

Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries.

Installation

• The TV set should be installed near an easily accessible AC power outlet.

• Place the TV set on a stable, level surface to avoid it from falling down and cause personal injury or damage to the TV.

• Only qualified service personnel should carry out wall installations.

• For safety reasons, it is strongly recommended that you use Sony accessories, including:

– KLV-37S550A/KLV-32S550A/

KLV-32S530A:

Wall-mount bracket SU-WL500 or

SU-WL50B

– KLV-26S550A:

Wall-mount bracket SU-WL100

• Be sure to use the screws supplied with the Wall-mount bracket when attaching the mounting hooks to the TV set. The supplied screws are designed so that they are 8 mm to 12 mm in length when measured from the attaching surface of the mounting hook.

The diameter and length of the screws differ depending on the Wall-mount bracket model.

Use of screws other than those supplied may result in internal damage to the TV set or cause it to fall, etc.

8mm - 12mm

Screw (supplied with the

Wall-mount bracket)

Mounting Hook

Hook attachment on rear of

TV set

Transporting

• Before transporting the TV set, disconnect all cables.

• Two or more people are needed to transport a large TV set.

• When transporting the TV set by hand, hold it as shown below. Do not put stress on the LCD panel.

• When lifting or moving the TV set, hold it firmly from the bottom.

• When transporting the TV set, do not subject it to jolts or excessive vibration.

• When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.

Ventilation

• Never cover the ventilation holes or insert anything in the cabinet.

• Leave space around the TV set as shown below.

• It is strongly recommended that you use a

Sony wall-mount bracket in order to provide adequate air-circulation.

Installed on the wall

30 cm

10 cm 10 cm

10 cm

Leave at least this space around the set.

Installed with stand

10 cm

30 cm

10 cm

6 cm

Leave at least this space around the set.

• To ensure proper ventilation and prevent the collection of dirt or dust:

– Do not lay the TV set flat, install upside down, backwards, or sideways.

– Do not place the TV set on a shelf, rug, bed or in a closet.

– Do not cover the TV set with a cloth, such as curtains, or items such as newspapers, etc.

– Do not install the TV set as shown below.

Air circulation is blocked.

Wall

AC power cord

Handle the AC power cord and outlet as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries:

– Use only Sony supplied AC power cords, not those of other brands.

– Insert the plug fully into the AC power outlet.

– Operate the TV set on a 110-240 V AC supply only (New Zealand and Tunisia only: 220-240 V AC).

– When wiring cables, be sure to unplug the

AC power cord for your safety and take care not to catch your feet on the cables.

– Disconnect the AC power cord from the

AC power outlet before working on or moving the TV set.

– Keep the AC power cord away from heat sources.

– Unplug the AC power plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate, which could result in a fire.

Notes

• Do not use the supplied AC power cord on any other equipment.

• Do not pinch, bend, or twist the AC power cord excessively. The core conductors may be exposed or broken.

• Do not modify the AC power cord.

• Do not put anything heavy on the AC power cord.

• Do not pull on the AC power cord itself when disconnecting the AC power cord.

• Do not connect too many appliances to the same AC power outlet.

• Do not use a poor fitting AC power outlet.

Prohibited Usage

Do not install/use the TV set in locations, environments or situations such as those listed below, or the TV set may malfunction and cause a fire, electrical shock, damage and/or injuries.

Location:

Outdoors (in direct sunlight), at the seashore, on a ship or other vessel, inside a vehicle, in medical institutions, unstable locations, near water, rain, moisture or smoke.

Environment:

Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc). The

TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV.

Situation:

Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer.

Disconnect the TV set from AC power outlet and antenna during lightning storms.

Be sure to hold the bottom of the panel, not the front part.

Continued

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Broken pieces:

• Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you have unplugged the AC power cord. Otherwise electric shock may result.

When not in use

• If you will not be using the TV set for several days, the TV set should be disconnected from the AC power for environmental and safety reasons.

• As the TV set is not disconnected from the

AC power when the TV set is just turned off, pull the plug from the AC power outlet to disconnect the TV set completely.

• However, some TV sets may have features that require the TV set to be left in standby to work correctly.

For children

• Do not allow children to climb on the TV set.

• Keep small accessories out of the reach of children, so that they are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the AC power cord immediately if any of the following problems occur.

Ask your dealer or Sony service centre to have it checked by qualified service personnel.

When:

– AC power cord is damaged.

– Poor fitting of AC power outlet.

– TV set is damaged by being dropped, hit or having something thrown at it.

– Any liquid or solid object falls through openings in the cabinet.

Precautions

Viewing the TV

• View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.

• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

LCD Screen

• Although the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.

• Do not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged.

• If this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.

• Ghosting may occur when still pictures are displayed continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this TV set is in use. This is not a malfunction.

• The LCD screen contains a small amount of liquid crystal. Mercury is sometimes contained depending on the kind of fluorescent tubes. Follow your local ordinances and regulations for disposal.

Handling and cleaning the screen surface/cabinet of the

TV set

Be sure to unplug the AC power cord connected to the TV set from AC power outlet before cleaning.

To avoid material degradation or screen coating degradation, observe the following precautions.

• To remove dust from the screen surface/ cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.

• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.

• Periodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.

• When adjusting the angle of the TV set, move it slowly so as to prevent the TV set from moving or slipping off from its table stand.

Optional Equipment

Keep optional components or any equipment emitting electromagnetic radiation away from the TV set. Otherwise picture distortion and/or noisy sound may occur.

Batteries

• Observe the correct polarity when inserting batteries.

• Do not use different types of batteries together or mix old and new batteries.

• Dispose of batteries in an environmentally friendly way. Certain regions may regulate the disposal of batteries. Please consult your local authority.

• Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote in a location near a heat source, a place subject to direct sunlight, or a damp room.

IMPORTANT INFORMATION

If a television is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

• Using cabinets or stands recommended by the manufacturer of the television.

• Only using furniture that can safely support the television.

• Ensuring the television is not overhanging the edge of the supporting furniture.

• Not placing the television on tall furniture

(for example, cupboards or bookcases) without anchoring both the furniture and the television to a suitable support.

• Not standing the televisions on cloth or other materials placed between the television and supporting furniture.

• Educating children about the dangers of climbing on furniture to reach the television or its controls.

Disposal of Old Electrical & Electronic

Equipment (Applicable in the

European Union and other European countries with separate collection systems)

This symbol is on the remote control.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Overview of the remote

z • The number 5, PROG + and

AUDIO buttons have tactile dots. Use the tactile dots as references when operating the TV.

1 "/1

– TV standby

Press to turn the TV on or to switch to standby mode.

AUDIO – Dual Sound (page 18)

SCENE – Scene Select mode

Press to display the “Scene Select” menu. When you select the desired scene option, the optimum sound and picture quality for selected scene are automatically set.

Sports: Delivers picture scenes that let you experience realistic picture and sound like those in a stadium.

Game: Delivers picture scenes that let you enjoy your game-playing experience to the fullest with superb picture and sound quality.

Cinema: Delivers picture scenes just like those in a theatre-like atmosphere with dynamic sound.

Music: Delivers sound effects that let you experience dynamic and clear sound like that at a concert.

General: Current user settings.

Coloured buttons

In Text mode: Accesses the corresponding coloured Fastext menu quickly and easily. The Fastext feature can be used only when the Fastext broadcast is available.

/ – Info / Text reveal

• Displays information. Press once to display current channel number, scene mode and screen mode. Press again to remove the display from the screen.

• In Text mode: Reveals hidden information (e.g. answers to a quiz).

/ – Item select / OK

• Selects or adjusts items.

• Confirms selected items.

TOOLS (page 10)

MENU

Displays or cancels the menu.

Number buttons

• Selects channels. For channel numbers 10 and above, enter the next digit

quickly (page 21).

• In Text mode: Enters the three digit page number to select the page.

– Favourite list

Display the Favourite list that you have specified (page 16).

– Previous channel

Returns to the previous channel watched (for more than five seconds).

PROG +/–/ /

• Selects the next (+) or previous (-) channel.

• In Text mode: Selects the next ( ) or previous ( ) page.

+/– – Volume

Adjusts volume.

qf %

– Mute

Press to mute the sound. Press again to restore the sound.

z • In standby mode, if you want to turn on the TV without sound, press this button.

/ – Text

In Text mode: Displays Text broadcast.

Each time you press /, the display changes cyclically as follows:

Text t Text over the TV picture (mix mode) t No Text (exit the Text service) qh

RETURN

Returns to the previous screen of any displayed menu.

– Twin Picture / PIP (page 14)

qk a – TV mode

Exit Text mode, or switches to a TV display when displaying external input.

/ – Input select / Text hold

• Displays the connected equipment list and selects the input source (page 13).

• In Text mode: Holds the current page.

– Wide Mode

Changes the picture size. Press repeatedly to select the desired wide mode.

Continued

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

For TV, Video, Component or HDMI (except

PC input)

Wide Zoom*

Enlarges the centre portion of the picture. The left and right edges of the picture are stretched to fill the

16:9 screen.

Normal

Displays the 4:3 picture in its original size. Side bars are shown to fill the

16:9 screen.

Full

Stretches the 4:3 picture horizontally to fill the 16:9 screen.

For PC Input

Normal

Full 1

Displays the picture in its original pixel size. Bars are shown at the top, bottom, and both sides for small picture.

Stretches the original picture to fill the screen vertically.

Full 2

Stretches the Full 1 picture horizontally to fill the 16:9 screen.

Zoom*

Displays cinemascopic (letter box format) broadcasts in the correct proportions.

• Some options may not be available depending on the

PC input signal.

* Parts of the top and bottom of the picture may be cut off.

• You cannot select “Normal” for HD signal source pictures.

Using the Tools menu

Press TOOLS enables you to access various options and change/make adjustments according to the source and screen mode. The options displayed vary depending on the input source.

Viewing TV programme

Options

Picture Mode

Sound Mode

Intelligent Picture

MPEG Noise Reduction

Speaker

Add to Favourites

Sleep Timer

Wake Up Timer

Power Saving

Listening FM Radio

Options

Sound Mode

Speaker

Sleep Timer

Wake Up Timer

Power Saving

FM Radio Set-up

Description

You can add the current channel to the favourite list.

Description

Viewing connected equipment

Options

Picture Mode (except PC input mode)

Display Mode (in PC input mode only)

Sound Mode

MPEG Noise Reduction

(except PC input mode)

Speaker

Twin Picture (except PC input mode)

PIP (in PC input mode only)

Single Picture (in Twin Picture and PIP mode only)

Audio Swap (in PIP mode only)

Auto Adjustment (in PC input mode only)

Horizontal Shift (in PC input mode only)

Sleep Timer (except PC input mode)

Wake Up Timer (except PC input mode)

Power Saving

Description

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Overview of the TV buttons and indicators

PROG

1 1

– Power

Turns the TV on or off.

• To disconnect the TV from the AC power completely, pull the plug from the AC power outlet.

PROG +/-/ /

• Selects the next (+) or previous (-) channel.

• In TV menu: Moves through the options up ( ) or down ( ).

3 2

+/-/ /

• Increases (+) or decreases (-) the volume.

• In TV menu: Moves through the options right

( ) or left ( ).

/ – Input select / OK

• Displays the connected equipment list and

selects the input source (page 13).

• In TV menu: Selects the menu or option, and confirms the setting.

Displays or cancels the menu.

– Remote sensor

Receives IR signals from the remote.

– Timer indicator

Lights up in amber when the timer is set (page 20).

8 1

– Standby indicator

Lights up in red when the TV is in standby mode.

9 "

– Power indicator

• Lights up in green when the TV is turned on.

• Flashes while the remote is being operated.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

D:\Chin Meng's job\SONY-LCD\SY0204_R1 (Rev-

3)\4130985131_GB\060OPT.fm

Using Optional Equipment

Connecting optional equipment

You can connect a wide range of optional equipment to your TV.

• The below terminals vary depending on TV models.

masterpage:Left

Headphones

S VHS/Hi8/

DVC camcorder

Home theatre system

DVD player with HDMI output

Blu-ray disc player

Digital video camcorder

Not available for

KLV-32S530A

For service use only

Video game equipment

DVD player without component video output

VCR

DVD player with component video output

DVD recorder

VCR

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Viewing pictures from the connected equipment

Turn on the connected equipment, then press / to display the connected equipment list. Press

F

f

to select the desired input source, then press . (The highlighted item is selected if 2 seconds pass without any operation after pressing

F

f

.) When the input source is set to “Skip” in the “Video Labels” under the “AV Set-up” menu

(page 19), that input does not appear in the list.

• Press / on the TV to display the connected equipment list and select the desired input source. You can also press

F/f to select the desired input source. Then wait for 2 seconds to display the selected input source.

Jacks/

Input symbol on screen

Description

Video 2

Connect to the video jack 2, and the audio jacks 2. If you connect mono equipment, connect to the L(MONO) jack 2.

B i

Video 1

Component

F PC IN

(RGB)/

G HDMI IN

HDMI

(For KLV-32S530A)

HDMI 1 or

HDMI 2

(For KLV-37S550A/

KLV-32S550A/

KLV-26S550A)

Connect to the i jack to listen to sound from the TV on headphones.

Connect to the video jack 1, and the audio jacks 1. If you connect mono equipment, connect to the L(MONO) jack 1.

Connect to the video output jack to record the image from the TV. Connect to the audio output jacks to record the sound from the TV on DVD recorder or

VCR. To turn off the sound of the TV speakers, set “Speaker” to “Audio System”

(page 19). If you connect mono equipment, connect to the L jack

• The monitor output jacks cannot support Component, HDMI and PC signals source pictures, also digital audio signal for sound.

Connect to the component jacks and the audio jacks / . For better picture quality, component connection is recommended if your DVD player has a component video output.

Connect to the PC IN (RGB) jack and the audio jack . It is recommended to use a PC cable with ferrite core.

Connect to the HDMI IN (KLV-32S530A), HDMI IN 1 or 2 (KLV-37S550A/

KLV-32S550A/KLV-26S550A) jack if the equipment has an HDMI jack. The digital video and audio signals are input from the equipment.

• The HDMI jacks only support the following video inputs: 480i, 480p, 576i, 576p, 720p

(50/60 Hz), 1080i (50/60 Hz) and 1080p (50/60 Hz).

• Be sure to use only an HDMI cable that bears the HDMI logo (recommended Sony

HDMI cable).

• To connect a PC, use the PC IN jack.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Viewing Twin Picture

You can view two pictures (external input and TV programme) on the screen simultaneously.

Connect the optional equipment (page 12), and make

sure that images from the equipment appear on the

screen (page 13).

Press .

Two pictures are displayed simultaneously.

Left

Window

Right Window

Twin Picture Availability

In Left Window In Right Window

Video 1

Video 2

No picture and no sound

Component

*HDMI (except PC input mode)

**HDMI 1 (except PC input mode)

**HDMI 2 (except PC input mode)

TV programme

* For KLV-32S530A

** For KLV-37S550A/KLV-32S550A/KLV-26S550A

Press

/

to select active picture.

Press number buttons or PROG +/– to select the TV channel.

To return to single picture mode

Press , or RETURN.

• You cannot change the size of the pictures.

• The picture and sound from the monitor output jacks

(refer D in page 12) will follow the left

picture (Video 1 or Video 2 only).

• In Twin Picture mode, as picture size reduced, this may decrease picture smoothness.

z • The highlighted picture is audible. You can switch the audible picture by pressing

G/g.

• You can also use the Twin Picture feature by selecting

“Twin Picture” from the Tools menu (page 10).

Viewing PIP (Picture in

Picture)

You can view two pictures (PC input and TV programme) on the screen simultaneously.

Connect a PC (page 12), and make sure that images

from a PC appear on the screen (page 13).

Press .

Two pictures are displayed simultaneously.

Main

Window

Sub Window

(Location of the sub window can be moved by pressing

F/f/G/g.

)

PIP Availability

In Main Window In Sub Window

PC TV programme

Press number buttons or PROG +/– to select the TV channel.

To return to single picture mode

Press

or

RETURN.

• You cannot display resolutions higher than WXGA

(1360 × 768 pixels).

• In PIP mode, as picture size reduced, this may decrease picture smoothness.

z • You can switch the audible picture by selecting

“Audio Swap” from the Tools menu (page 10).

• You can also use the PIP feature by selecting “PIP”

from the Tools menu (page 10).

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

D:\Chin Meng's job\SONY-LCD\SY0204_R1 (Rev-

3)\4130985131_GB\070MEN.fm

masterpage:Left

Using MENU Functions

Navigating through menus

“MENU” allows you to enjoy various convenient features of this TV. You can easily select channels or inputs sources, preset FM radio stations and change the settings for your TV.

Press MENU.

Press

/

to select an option, then press .

To exit the menu, press MENU.

Menu Descriptions

Favourites

Displays the favourite list (page 16).

• To watch the desired channel, select the favourite channel number, then press .

• To add the current channel to the favourite list, select “Add to

Favourites”. When the favourite list is full, select “Edit Favourites” to

remove any channel from your list and try again (page 16).

2 Programme

List

External

Inputs

Displays available TV channels.

• To watch the desired channel, select the channel, then press .

• To assign a label to a channel, select “Edit Programme Labels”, then see

page 21.

Selects equipment connected to your TV.

• To watch the desired external input, select the input source, then press

• To assign a label to an external input, select “Edit Video Labels”, then

see page 19.

4 FM Radio

Listens to the FM Radio (page 15).

Settings Displays the “Settings” menu where most of the advanced settings and

adjustments are performed. For details about settings, see page 17 to

23.

Listening to the FM Radio

You are able to listen to the FM radio stations using your TV by connecting an antenna (page 4). FM Radio tuning

range is from 87.5-108.0 MHz.

Access to FM Radio mode

Exit from FM Radio mode

Listen to preset stations

Do this

Press MENU and select “FM Radio”.

Press MENU, select the desired items: “Programme List” or “External Inputs”, then press . Select the desired TV channels or external inputs and press .

1 Access to FM Radio mode.

2 Press MENU and select “Settings”. Preset the desired FM radio stations and its labels

in “FM Radio Set-up” from “Channel Set-up” menu (page 23).

• You can also access to “FM Radio Set-up” by selecting “FM Radio Set-up” from the

Tools menu in FM Radio mode

(page 10)

3 Exit from “Channel Set-up” menu by pressing MENU. The selected preset FM radio station number and label will appear on the screen. To select the desired preset FM radio station, press PROG +/–.

• You can also use the 1-9 buttons on the remote to directly select the desired preset

FM radio station.

Continued

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Listen to non-preset stations

Do this

1 Access to FM Radio mode.

2 Press

F/f to automatically search for the desired FM radio station.

• You can also manually search for the desired FM radio station by pressing

G/g. The available radio frequency is only for temporary listening pleasure and cannot be stored in the memory.

• If the message “Please set-up FM Radio.” appears, display the “Channel Set-up” menu and select “FM Radio Set-up” to preset the desired FM radio stations

(page 23).

• If the station has a noisy sound, you may be able to improve the sound quality by pressing G/g.

• When a FM stereo programme has static noise, press AUDIO until “Mono” appears. There will be no stereo effect, but the noise will be reduced.

Using the Favourite List

The Favourite feature lets you select programmes from a list of up to 16 favourite channels that you specify.

Press MENU.

Press

/

to select “Favourites”, then press .

Perform the desired operation as shown in the following table or displayed on the screen.

Favourite List

Watch a channel

Turn off the Favourite list

Add a current channel to the

Favourite list

Remove a channel from the

Favourite list

Do this

Press

F/f

to select the channel number, then press .

Press RETURN to return to the previous screen.

Press MENU or to exit the menu.

Press

F/f

to select “Add to Favourites”, then press .

Press

F/f

to select “Edit Favourites”, then press .

The “Favourite Set-up” screen appears. For details, see “Favourite Set-up” on page 21.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Settings adjustment

You are able to change the settings of your TV from “Settings” menu.

Press MENU. Press F/f to select “Settings”, then press .

Press F/f to select a menu icon, then press

Press F/f/G/g to select an option or adjust a setting, then press .

• The options you can adjust vary depending on the situation. Unavailable options are greyed out or not displayed.

Picture menu

Picture Mode

Display Mode

(only in PC mode)

Reset

Backlight

Picture

Brightness

Colour

Hue

Colour Temperature

Sharpness

Noise Reduction

MPEG Noise

Reduction

Advanced Settings

Selects the picture mode except for PC input source.

“Vivid”: For enhanced picture contrast and sharpness.

“Standard”: For standard picture. Recommended for home entertainment.

“Cinema”: For optimum picture quality of film videos.

Selects the display mode for PC input source.

“Video”: For video images.

“Text”: For text, charts or tables.

Resets all the “Picture” settings except “Picture Mode” and “Display Mode” to the factory settings.

Adjusts the brightness of the backlight.

Increases or decreases picture contrast.

Brightens or darkens the picture.

Increases or decreases colour intensity.

Increases or decreases the green tones and red tones.

• “Hue” can only be adjusted for an NTSC colour system (e.g. U.S.A. video tapes).

Adjusts the whiteness of the picture.

“Cool”: Gives the white colours a blue tint.

“Neutral”: Gives the white colours a neutral tint.

“Warm 1”/“Warm 2”: Gives the white colours a red tint. “Warm 2” gives a redder tint than “Warm 1”.

• “Warm 1” and “Warm 2” are not available when “Picture Mode” is set to “Vivid”.

Sharpens or softens the picture.

Reduces the picture noise (snowy picture) in a weak broadcast signal.

“High”/“Medium”/“Low”: Modifies the effect of the noise reduction.

“Off

”: Turns off the “Noise Reduction” feature.

Reduces the picture noise in MPEG-compressed video.

Choose either “High”, “Medium”, “Low” or “Off ”.

Customises the “Picture” function in more detail. When you set “Picture Mode” to

“Standard” or “Cinema”, you can set/change these settings.

“Reset”: Resets all the advanced settings to the factory settings.

“Adv. Contrast Enhancer”: Automatically adjusts “Backlight” and “Picture” to the most suitable settings judging from the brightness of the screen. This setting is especially effective for dark images scenes. It will increase the contrast distinction of the darker picture scenes.

“Gamma”: Adjusts the balance between bright and dark areas of the picture.

“Clear White”: Emphasises white colours.

“Live Colour”: Makes colours more vivid.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Sound menu

Sound Mode

Reset

5 Band Equalizer

Balance

Intelligent Volume

Volume Offset

Surround

Dual Sound

“Dynamic”: Enhances treble and bass. Recommended for home entertainment.

“Standard”: For standard sound.

“Clear Voice”: Makes voice sound clearer.

Resets all the “Sound” settings except “Sound Mode” and “Dual Sound” to the factory settings.

Adjusts sound frequency settings.

1

Make sure that “Adjust” is selected, then press .

Selecting “Reset” will set your TV to the factory settings.

2

Press G/g to select the desired sound frequency, then press F/f to adjust the setting and press . The adjusted settings will be received when you select “Sound Mode” options.

• Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency will affect lower pitched sound.

Emphasises left or right speaker balance.

Minimizes the difference in volume level between all programmes and adverts (e.g. adverts tend to be louder than programmes).

Adjusts the volume level of the current input relative to other inputs.

Choose either “On” (surround), “Simulated Stereo” (stereo-like monaural sound) or “Off”.

Selects the sound from the speaker for a stereo or bilingual broadcast.

The selection varies, depending on the Broadcasting.

Broadcasting

NICAM stereo

NICAM bilingual

NICAM monaural

A2 (German) stereo

Selection

Stereo (stereo sound)/Mono (regular sound)

Main (main sound)/Sub (sub sound)/Mono (regular sound)

Main (main sound)/Mono (regular sound)

Stereo (stereo sound)/Mono (regular sound)

A2 (German) bilingual Main (main sound)/Sub (sub sound)

• If the signal is very weak, the sound becomes monaural automatically.

• If the stereo sound is noisy when receiving a NICAM programme, select “Mono”. The sound becomes monaural, but the noise is reduced.

• The “Dual Sound” setting is memorised for each programme position.

• You cannot receive a stereo broadcast signal when “Mono” is selected for the programme position.

• If you select other equipment connected to the TV, set “Dual Sound” to “Stereo”, “Main” or “Sub”. However, when the external equipment connected to the HDMI jack is selected, this is fixed to “Stereo”.

• If you access to FM Radio mode, set “Dual Sound” to “Stereo” or “Mono”.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Screen menu

Wide Mode

Auto Wide

4:3 Default

Display Area

Horizontal Shift

Vertical Shift

Vertical Size

For details about wide mode, see page 10.

Automatically changes the wide mode according to the input signal from an external equipment. To keep your setting, select “Off”.

• “Auto Wide” is only available when watching programmes from video input, HDMI and component input in format 480i or 576i.

z • Even if “Auto Wide” is set to “On” or “Off”, you can always modify the format of the screen by pressing repeatedly.

Selects the default screen mode for use with 4:3 broadcasts.

“Wide Zoom”: Displays conventional 4:3 broadcasts with an imitation wide screen effect.

“Normal”: Displays conventional 4:3 broadcasts in the correct proportions.

“Off”: Keeps the current “Wide Mode” setting when the channel or input is changed.

• “4:3 Default” is available only if “Auto Wide” is set to “On”.

Adjusts the screen area for displaying the picture.

“Normal”: Displays the picture in the original size.

“-1”/“-2”: Enlarges the picture to hide the edge of the picture.

Adjusts the horizontal position of the picture.

Adjusts the vertical position of the picture when “Wide Mode” is set to “Zoom”.

Adjusts the vertical size of the picture when “Wide Mode” is set to “Wide Zoom” or

“Zoom”.

Set-up menu

Auto Start-up

Language

AV Set-up

Starts the initial set-up procedure. Usually, you do not need to do this operation because

it was done when the TV was first installed (page 5). However, this option allows you

to repeat the process (e.g. to retune the TV after moving house, or to search for new channels that have been launched by broadcasters).

Selects the language in which the menus are displayed.

Video Labels

Assigns a name to any equipment connected to the side and rear jacks. The name will be displayed briefly on the screen when the equipment is selected. You can skip input signals from connected equipment that you do not want displayed on the screen.

1

Press

/ f

to select the desired input source, then press .

2

Press

/ f

to select the desired option below, then press .

Equipment labels: Uses one of the preset labels to assign a name to connected equipment.

“Edit:”: Creates your own label. Follow steps 2 to 4 of “Programme Labels”

(page 21).

“Skip”: Skips an unnecessary input source.

Speaker

Turns on/off the TV’s internal speakers.

“TV Speaker”: The TV speakers are turned on in order to listen to the TV’s sound through the TV speakers.

“Audio System”: The TV speakers are turned off in order to listen to the TV’s sound only through your external audio equipment connected to the audio output jacks.

• All items in “Sound” menu except “Dual Sound” are not available when “Speaker” is set to

“Audio System”.

Continued

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Timer Settings

Product Information

Factory Settings

Colour System

Selects the colour system (“Auto”, “PAL”, “SECAM”, “NTSC3.58”, “NTSC4.43” or

“PAL60”) according to the composite video signal from the input source.

Sets the timer to turn on/off the TV.

Sleep Timer

Sets the TV to automatically switch to standby mode after a certain amount of time.

z • If you turn off the TV and turn it on again, “Sleep Timer” is reset to “Off”.

• A notification message appears on the screen one minute before the TV switches to standby mode.

Wake Up Timer

Sets the desired period of time to turn on the TV from standby mode.

“Time”: Sets the desired period of time to turn on the TV.

“Duration”: Sets how long you want the TV to stay on before switching to standby mode again.

• When the “Sleep Timer” or “Wake Up Timer” is activated, the (Timer) indicator on the

TV front panel lights up in amber.

Displays your TV’s product information.

Resets all settings to factory settings other than “Programme Block”, programme preset data and the FM Radio preset data. After completing this process, the initial set-up screen is displayed the next time you turn on the TV. Completing auto tuning in initial set-up will reset these settings. To keep them, select “Cancel” in the auto tuning confirmation dialogue.

• Be sure not to turn the TV off during this period (it takes about 30 seconds) or press any buttons.

PC Settings menu

Wide Mode

Reset

Auto Adjustment

Phase

Pitch

Horizontal Shift

Selects a screen mode for displaying input from your PC, see page 10.

“Normal”: Displays the picture in its original size.

“Full 1”: Enlarges the picture to fill the display area, keeping its original horizontal-tovertical aspect ratio.

“Full 2”: Enlarges the picture to fill the display area.

Resets all the “PC Settings” except “Wide Mode” to the factory settings.

Automatically adjusts the display position and phase of the picture when the TV receives an input signal from the connected PC.

• “Auto Adjustment” may not work well with certain input signals. In such cases, manually adjust “Phase” and “Horizontal Shift”.

Adjusts the phase when the screen flickers.

Adjusts the pitch when the picture has unwanted vertical stripes.

Adjusts the horizontal position of the picture.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

PC Input Signal Reference Chart for supported signals and “Resolution:” value displayed

Signals

VGA

SVGA

XGA

WXGA

Horizontal (Pixel) Vertical (Line)

640

640

720

800

800

1024

1024

1280

1360

480

480

400

600

600

768

768

768

Horizontal frequency

(kHz)

31.5

37.5

31.5

37.9

46.9

48.4

56.5

47.4

47.8

47.7

Vertical frequency

(Hz)

Standard

VGA

VESA

VGA-T

VESA Guidelines

VESA

VESA Guidelines

VESA

VESA

• This TV’s PC input does not support Sync on Green or Composite Sync.

• This TV’s PC input does not support interlaced signals.

• If input signal is not shown in above chart, then this signal may not be displayed properly or cannot be displayed according to your settings. z • For the best picture quality, it is recommended to use the signals (boldfaced) in the above chart with a 60 Hz vertical frequency from a personal computer. In plug and play, signals with a 60 Hz vertical frequency will be selected automatically.

Channel Set-up menu

1 Digit Direct

Favourite Set-up

Auto Tuning

Programme Sorting

Programme Labels

Programme Block

When “1 Digit Direct” is set to “On”, you can select a channel using one preset number button (0 - 9) on the remote.

• When “1 Digit Direct” is set to “On”, you cannot select channel numbers 10 and above entering next digit using the remote.

Allows you to set your favourite channels by assigning the desired channel numbers.

1

Press

/ f

to select your favourite channel number, then press .

2

Press

/ f

to select your desired channel, then press .

To reset the Favourite channels

Select “_ _”, then press .

Repeat the procedure above to set other favourite channels.

Tunes in all the available channels. This option allows you to retune the TV after moving house, or to search for new channels that have been launched by broadcasters.

Changes the order in which the channels are stored on the TV.

1

Press

/ f

to select the channel you want to move to a new position, then press .

2

Press

/ f

to select the new position for your channel, then press .

Assigns a channel name of your choice up to five letters or numbers. The name will be displayed briefly on the screen when the channel is selected.

1

Press

/ f

to select the channel you want to name, then press .

2

Press

/ f

to select the desired letter or number (“_” for a blank space), then press g

If you input a wrong character

Press

G

g

to select the wrong character. Then, press

F

f

to select the correct character.

To delete all the characters

Select “Reset”, then press .

3

Repeat the procedure in step 2 until the name is completed.

4

Select “OK”, then press .

Blocks an individual channel from being watched.

1

Press

/ f

to select the channel you want to block, then press .

2

Press

/ f

to select “Block”, then press . To watch the channel, select “Allow”.

Continued

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Intelligent Picture

Manual Programme

Preset

“On with Indicator”: Automatically reduces the picture noise. The signal level bar is displayed when the channel is changed or the display is changed from an input screen to a TV programme.

“On”: Automatically reduces the picture noise.

“Off”: Turns off the “Intelligent Picture” feature.

Before selecting “Label”/“AFT”/“Skip”/“Colour System”/“Signal Booster”, press

PROG +/- to select the programme number with the channel. You cannot select a

programme number that is set to “Skip” (page 22).

Programme/TV System/VHF or UHF

Presets programme channels manually.

1

Select “Programme”, then press .

2

Press

/ f

to select the programme number you want to manually tune

(if tuning a VCR, select channel 000), then press RETURN.

3

Press

/ f

to select “TV System”, then press .

4

Press

/ f

to select your TV broadcast systems, then press .

5

Press

/ f

to go to the frequency range indication (“VHF Low”, “VHF High” or

“UHF”), then press .

6

Tune the channels as follows:

Press

/ g

to search for the next available channel. When a channel has been found, the search will stop. To continue searching, press

/ g

Repeat the procedure above to preset other channels manually.

Label

Assigns a name of your choice, up to five letters or numbers, to the selected channel.

This name will be displayed briefly on the screen when the channel is selected.

To input characters, follow steps 2 to 4 of “Programme Labels” (page 21).

AFT

Allows you to fine-tune the selected programme number manually if you feel that a slight tuning adjustment will improve the picture quality. You can adjust the fine tuning over a range of -15 to +15. When “On” is selected, the fine tuning is performed automatically.

Skip

Skips unused channels when you press PROG +/- to select channels. (You can still select a skipped channel using the number buttons.)

Colour System

Selects the colour system (“Auto”, “PAL”, “SECAM”, “NTSC3.58”, “NTSC4.43” or

“PAL60”) according to the channel.

Signal Booster (Intelligent Signal Booster)

Improves the picture quality if the TV signal is too strong or weak.

Press

/ f

to select either “Off” if the signal is too strong (picture distorted; picture with lines; signal interference) or “Auto” if the signal is weak (snowy picture), then press .

Signal Level

Displays the signal level for programme currently being watched.

red

(weak) amber

(average) green

(good)

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

FM Radio Set-up

(only in FM Radio mode)

Preset up to nine FM radio stations. You can manually preset each FM radio station that can be received in your area and then store the radio frequency of the desired FM radio stations.

1

Press

/ f

to select the desired FM radio station position, then press .

2

Press

/ f

to search the FM radio stations. Searching stops automatically when a station is tuned in. If the station has a noisy sound, you may be able to improve the sound quality by pressing

/ g

. Press twice to store the FM radio station.

3

You may edit the FM radio station label. Press

/ f

to select alphanumeric characters for the label, then press .

4

Repeat steps 1 to 3 to preset other FM radio stations.

• To enable this feature, access to FM Radio mode by using MENU (page 15), then preset

your desired FM radio stations according to the steps mentioned above.

Eco menu

Power Saving

Idle TV Standby

Selects the power saving mode to reduce the power consumption of the TV. Choose either “Standard Power” or “Reduced Power”.

Selects the time (“1h”, “2h” or “3h”) to set the TV into standby mode automatically, if you do not operate the TV for the specified period of time.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

D:\Chin Meng's job\SONY-LCD\SY0204_R1 (Rev-

3)\4130985131_GB\080ADD.fm

masterpage:Left

Additional Information

Installing the Accessories (Wall-Mount Bracket)

To Customers:

For product protection and safety reasons, Sony strongly recommends that installing of your TV be performed by

Sony dealers or licensed contractors. Do not attempt to install it yourself.

To Sony Dealers and Contractors:

Provide full attention to safety during the installation, periodic maintenance and examination of this product.

Your TV can be installed using the Wall-Mount Bracket SU-WL500, SU-WL50B or SU-WL100 (sold separately).

• Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the installation.

• Refer to “Detaching the Table-Top Stand from the TV” (page 6).

• Refer to “TV installation dimensions table” (page 25).

• Refer to “Screw and Hook locations diagram/table” (page 26).

• Place the TV on the Table-Top Stand, when securing the Mounting Hook.

SU-WL500: SU-WL50B: SU-WL100:

Screw

(+PSW

6 × 16)

Screw

(+PSW

4 × 12)

Screw

(+PSW

6 × 16)

Square hole

Mounting Hook

Sufficient expertise is required for installing these products, especially to determine the strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of these products to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any damage or injury caused by mishandling or improper installation.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

TV installation dimensions table

SU-WL500:

SU-WL50B:

Screen centre point a b c c b a

Model Name

KLV-37S550A

KLV-32S550A/

KLV-32S530A

Screen centre point

Display dimensions

927

807

574

508

Unit: mm

Screen centre dimension

SU-

WL500

140

SU-

WL50B

193

SU-

WL500

432

Length for each mounting angle

Angle (0°) Angle (20°)

F G H

SU-

WL50B

484

SU-

WL500

156

SU-

WL50B

157 324

SU-WL500 only

542 468

172 200 430 458 154 155 300 485 466

SU-WL100:

Screen centre point

Model Name

KLV-26S550A

Display dimensions

A B

679 435

Screen centre dimension

Unit: mm

Length for each mounting angle

Angle (0°) Angle (20°)

F G H

318 154 258 411 323

Figures in the above table may differ slightly depending on the installation.

WARNING

The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the

TV. Refer to “Specifications” for its weight.

Continued

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Screw and Hook locations diagram/table

Screw location - When installing the Mounting Hook on the TV.

SU-WL500

SU-WL50B

Hook location - When installing the TV onto the Base Bracket.

SU-WL500 SU-WL50B

a* b c a* b c a b c

Hook c b a a b c

Base Bracket c b a

SU-WL100

a b*

* Hook location “a” cannot be used for the models in the table below.

Model Name

KLV-37S550A

KLV-32S550A/KLV-32S530A

KLV-26S550A

* Hook location “b” cannot be used for the models in the table below.

Screw location

SU-WL500 d, g e, g

SU-WL50B d, i e, h

Hook location

SU-WL500 SU-WL50B b c

SU-WL100 a

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Troubleshooting

Check whether the 1 (standby) indicator is flashing in red.

When it is flashing

The self-diagnosis function is activated.

Count how many times the 1 (standby) indicator flashes between each two second break.

For example, the indicator flashes three times, then there is a two second break, followed by another three flashes, etc.

Press 1 on the TV to turn it off, disconnect the AC power cord, and inform your dealer or

Sony service centre of how the indicator flashes (number of flashes).

When it is not flashing

Check the items listed below.

If the problem still persists, have your TV serviced by qualified service personnel.

Picture

No picture (screen is dark) and no sound

• Check the antenna/cable connection.

• Connect the TV to the AC power outlet, and press 1 on the TV.

• If the 1 (standby) indicator lights up in red, press "/1.

No picture or no menu information from equipment connected to the video input jack appears on the screen

• Press / to display the connected equipment list, then select the desired input.

• Check the connection between the optional equipment and the TV.

Double images or ghosting

• Check the antenna/cable connection.

• Check the antenna/cable location and direction.

Only snow and noise appear on the screen

• Check if the antenna is broken or bent.

• Check if the antenna has reached the end of its serviceable life (three to five years in normal use, one to two years at the seaside).

Distorted picture (dotted lines or stripes)

• Keep the TV away from electrical noise sources such as cars, motorcycles, hair-dryers or optional equipment.

• When installing optional equipment, leave some space between the optional equipment and the TV.

• Check the antenna/cable connection.

• Keep the antenna cable away from other connecting cables.

Picture or sound noise when viewing a TV channel

• Adjust “AFT” (Automatic Fine Tuning) to obtain better

picture reception (page 22).

Some tiny black points and/or bright points appear on the screen

• The picture of a display unit is composed of pixels. Tiny black points and/or bright points (pixels) on the screen do not indicate a malfunction.

No colour on programmes

• Select “Reset” (page 17).

No colour or irregular colour when viewing a signal from the Y, P

, P

jacks of /

• Check the connection of the Y, P

, P

jacks of

/ and check if each jacks are firmly seated in their respective jacks.

Sound

No sound, but good picture

• Press 2 +/– or % (Mute).

• Check if the “Speaker” is set to “TV Speaker” (page 19).

General

The TV turns off automatically (the TV enters standby mode)

• Check if the “Sleep Timer” is activated, or confirm the

“Duration” setting of “Wake Up Timer” (page 20).

• Check if the “Idle TV Standby” is activated (page 23).

The TV turns on automatically

• Check if the “Wake Up Timer” is activated (page 20).

Some input sources cannot be selected

• Select “Video Labels” and cancel “Skip” of the input

source (page 19).

The remote does not function

• Replace the batteries.

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Specifications

Model name

System

Panel System

TV System

Colour System

Channel Coverage

KLV-37S550A KLV-32S550A KLV-32S530A KLV-26S550A

LCD (Liquid Crystal Display) Panel

B/G, I, D/K, M

PAL, PAL60, SECAM, NTSC4.43, NTSC3.58

B/G: VHF: E2 to E12/ UHF: E21 to E69/ CATV: S01 to S03, S1 to S41

VHF: 1 to 11/UHF: 21 to 69/ CATV: S01 to S03, S1 to S41 (New Zealand only)

I: UHF: B21 to B69/ CATV: S01 to S03, S1 to S41

D/K: VHF: C1 to C12, R1 to R12/ UHF: C13 to C57, R21 to R60/ CATV: S01 to S03, S1 to S41,

Z1 to Z39

M: VHF: A2 to A13/ UHF: A14 to A79/ CATV: A-8 to A-2, A to W+4, W+6 to W+84

10 W + 10 W 8 W + 8 W

Sound Output

Input/Output jacks

Antenna

1, 2

75 ohm external terminal

Video input (phono jack)

Audio input (phono jacks): 500 mVrms, Impedance: 47 kilohms

Supported formats: 1080p (50/60 Hz), 1080i (50/60 Hz), 720p (50/60 Hz), 576p, 576i, 480p, 480i

Y: 1 Vp-p, 75 ohms, 0.3V sync negative/P

: 0.7 Vp-p, 75 ohms/P

: 0.7 Vp-p, 75 ohms

Audio input (phono jacks): 500 mVrms, Impedance: 47 kilohms

Video output (phono jack)

Audio output (phono jacks)

Video: 1080p (50/60 Hz), 1080i (50/60 Hz), 720p (50/60 Hz), 576p, 576i, 480p, 480i HDMI IN (KLV-32S530A)

HDMI IN 1, 2 (KLV-37S550A/

KLV-32S550A/KLV-26S550A)

PC IN (RGB)

PC IN i

Power and others

Power Requirements

PC Input (D-sub 15-pin) (see page 21)

G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms/

R: 0.7 Vp-p, 75 ohms/HD: 1-5 Vp-p/VD: 1-5 Vp-p

PC audio input (minijack)

Headphones jack

Screen Size (inches)

Display Resolution

Power Consumption

Dimensions

(w × h × d)* with stand (mm) without stand

(mm)

Mass*

Optional

Accessories with stand (kg) without stand

(kg)

Wall-Mount bracket

110–240 V AC, 50/60 Hz

220–240 V AC, 50/60 Hz (New Zealand and Tunisia only)

37 32

1,366 pixels (horizontal) × 768 lines (vertical)

Indicated on the rear of the TV.

927 × 627 × 259 807 × 557 × 222 807 × 557 × 222

927 × 574 × 103

16.1

14.3

807 × 508 × 102

13.1

12.0

SU-WL500 or SU-WL50B

* Dimensions and mass are approximate values.

Design and specifications are subject to change without notice.

807 × 508 × 102

13.1

12.0

679 × 485 × 222

679 × 435 × 101

10.0

8.7

SU-WL100

Instructions on “Installing the Wall-Mount Bracket” are not supplied in the form of a separate leaflet with this TV.

These installation instructions are included within this

TV’s instructions manual.

Printed on 70% or more recycled paper using VOC

(Volatile Organic Compound)-free vegetable oil based ink.

Customer support

Printed in Malaysia

KLV-37/32/26S550A/KLV-32S530A

4-130-985-13(1)

Reklaam

LCD Colour TV

Operating Instructions

Introduction

Trademark information

Notes for Australia and New Zealand model

Table of Contents

Start-up Guide

Using Optional Equipment

Using MENU Functions

Additional Information

Start-up Guide

Checking the accessories

2: Connecting an antenna/ cable/VCR

1: Attaching the stand

3: Preventing the TV from toppling over

4: Bundling the cables

5: Performing the initial set-up

3, 4, 5, 6, 9

Install a wood screw (4 mm in diameter, not supplied) in the TV stand.

Install a machine screw (M4 × 14, not supplied) into the screw hole of the TV.

For KLV-32S550A/KLV-32S530A/

KLV-26S550A:

Attach a nut (M4, not supplied) from the bottom of the Table-Top Stand to the screw securely.

Tie the wood screw and the machine screw with a strong cord.

8

Connect the TV to your AC power outlet

(110-240 V AC, 50/60 Hz) (New Zealand and Tunisia only: 220-240 V AC, 50/60 Hz).

Press 1 on the TV.

Selecting the language, country/ region and location

Follow the instructions on the screen.

Press

/

to select the language displayed on the menu screens, then press .

Press

/

to select the country/region, then press .

Press

/

to select “Home”, then press .

Auto-tuning the TV

Press

/

to select “OK”, then press .

When the “Programme Sorting” menu appears on the screen, follow the steps of

“Programme Sorting” (page 21).

Press MENU to exit.

Press

/

to select the desired setting in

“Display this menu next time?” dialogue, then press to exit.

Watching TV

Press 1 on the TV to turn on the TV.

Press the number buttons or PROG +/– to select a TV channel.

Press 2 +/– to adjust the volume.

Detaching the Table-Top

Stand from the TV

Safety information

Installation/Set-up

AC power cord

Prohibited Usage

Broken pieces:

When not in use

For children

If the following problems occur...

Precautions

Overview of the remote

For TV, Video, Component or HDMI (except

PC input)

For PC Input

Using the Tools menu

Overview of the TV buttons and indicators

Using Optional Equipment

Connecting optional equipment

Viewing pictures from the connected equipment

F

f

F

f

Viewing Twin Picture

Press .