SAFETY AND INSTALLATION INSTRUCTIONS Model: FL124BPIR

SAFETY AND INSTALLATION INSTRUCTIONS Model: FL124BPIR
SAFETY AND INSTALLATION
INSTRUCTIONS
Model: FL124BPIR
24W Low Energy Floodlight with PIR
IMPORTANT! Please read these instructions before installing your new fitting.
Please retain for future reference.
Pack Contents
Floodlight
24W Compact Fluorescent Lamp
x1
x1
General Information, Safety and Installation Instructions
Introduction
The chosen location of your new fitting should allow
for the product to be securely mounted and safely
connected to the mains supply (lighting circuit).
Your new floodlight incorporates a PIR (Passive Infra
Red) sensing device which is sensitive to movement
of warm objects within a preset operating zone and
immediately switches the light on when movement is
detected.
When choosing the location for your new fitting,
ensure that the fixings will be anchored in a solid
surface e.g. concrete, brick or a joist—do not fix directly
onto panelling, cladding, plasterboard etc.
This makes this fitting ideal for automatically
illuminating pathways, steps, patios, porches, or
whatever area you have selected to light for reasons
of safety, convenience or security. While there is
movement within range of the unit the light will
remain on.
If the location of your new fitting requires the provision
of a new electrical supply, the supply must conform
with the requirements of the Building Regulations
making reference to the current edition of the IEE
Wiring Regulations (BS7671).
This product is designed for permanent connection to
fixed wiring: this should be either a suitable lighting
circuit (protected with a 5 or 6 Amp MCB or fuse) or a
fused spur (with a 3 Amp fuse) via a fused connection
unit.
Read this first
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not, contact
the outlet where you bought this product.
We recommend that the supply incorporates a switch
for ease of operation.
This product contains glass, care must be taken when
assembling, fitting or handling to prevent personal
injury or damage to the product.
Make connections to the electrical supply in
accordance with the following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
This light fitting must be installed by a competent
person in accordance with the Building Regulations
making reference to the current edition of the IEE
Wiring Regulations (BS7671). The Building Regulations
may be obtained from HMSO or viewed and
downloaded from www.communities.gov.uk following
the link for Building Regulations.
When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened onto
the bared conductors and not onto any insulation.
As the buyer, installer and/or user of this product it is
your own responsibility to ensure that this fitting is fit
for the purpose for which you have intended it. Eterna
Lighting cannot accept any liability for loss, damage or
premature failure resulting from inappropriate use.
This product must be connected to Earth.
IMPORTANT - Always switch off at the mains before
changing the lamp.
Do not mount on a surface that is likely to vibrate.
If in any doubt, consult a qualified electrician.
TIME SENS
For maximum detection area, the light should be
mounted 1.8 to 2.5 meters (6 to 8ft) above the
��������������
�������������
detection
area (refer Fig.1A). The
floodlight scanning
specifications (approximately 12 meters at 180°) may
vary slightly depending on the mounting height and
location.
LUX
The lamps (bulbs/tubes) supplied with this fitting are
consumable parts and therefore may be outside of any
warranty offered.
Switch off the mains before commencing installation
�������������������
and remove the appropriate
circuit fuse.
When working at heights, please use a suitable
platform.
Disconnect the fitting from the electrical supply before
flash or high voltage testing.
Suitable for indoor and outdoor use.
Issue 090714-1PA
This product is suitable for installation on surfaces
with normal flammability e.g. wood, plasterboard, and
masonry. It is not suitable for use on highly flammable
surfaces (e.g. polystyrene, textiles).
�������
����
���������
������
Before making fixing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
��
��
���
������������������������
2
Installation Instructions and Care
of the washers, it is important to fit them in the
correct order (see Fig. 2)
The detection range of the unit may alter with changes
in ambient temperature.
To avoid damage to the PIR unit, do not aim the
sensor towards the sun.
3.
To avoid nuisance triggering, the sensor should be
directed away from heat sources such as barbecues,
air-conditioners, other outside lighting, moving cars
and flue vents.
Using the fixing strap as a template, mark the
position for the fixing holes on your mounting
surface.
4. Prepare your mounting surface as appropriate for
your chosen fixings (not supplied). Use a spirit
level to ensure the fitting will be level.
Do not connect to circuits with other light fittings or
appliances such as large fans, washing machines,
fluorescent lights etc. that may cause false triggering
through spikes generated in the mains supply.
Do not aim towards reflective surfaces such as smooth
white walls, swimming pools, etc.
Before selecting a place to install your floodlight you
should note that movement across the scan area is
more effective than movement directly towards or
away from the sensor (refer Fig.1B). When walking
directly towards or away from the sensor rather
than across, the apparent detection range will be
substantially reduced (refer Fig. 1C).
5.
Secure the strap in place.
6.
Fit the floodlight back onto the fixing strap and
replace the screws.
7.
Before tightening the screws at the ends of the
fixing strap, adjust the position of the floodlight to
give the desired area of illumination.
8.
Tighten the screws to lock your floodlight in
position.
9.
Undo the four screws in the connection box cover
and remove it, take care not to lose any of the
screws or the sealing gasket.
10. Undo the screws and lift off the cable clamp.
11. Undo and remove the cable entry nut and gland.
12. If necessary, pierce the gland making a hole
just large enough for your supply cable to pass
through so that the gland makes a tight seal
around it.
13. Thread your supply cable through the nut and
gland and into the connection box.
��������������
14. Make the connections to your mains supply as
described in the “Read this first” section.
�������������
Do not attempt to modify the light or PIR sensor unit,
there are no user serviceable parts inside.
15. Replace the cable grip and connection box cover
ensuring that the cable is held securely and the
gasket is correctly positioned.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation there
are electrical tests that should be carried out: these
tests are specified in the Wiring Regulations (BS7671)
referred to in the Building Regulations. If in doubt,
consult a qualified electrician.
Installation
16. Using a cross-headed screwdriver, undo the
screws that secure the diffuser and allow to hang
down.
17. Fit the fluorescent lamp by pressing straight into
the lampholder.
18. Replace the diffuser and tighten the screws
making sure that the waterproof gasket is correctly
positioned and compressed.
�������
����
1.
Choose the location for your new floodlight giving
���������
consideration
to all of the conditions listed above.
2.
Loosen the screws at each end of the fixing
�� the position
�� it. Note
���of each
bracket and remove
������
������������������������
19. Restore the power and switch on.
3
Installation Instructions & Care
����������������
Fig. 2
�����������
�����������������
��������������
�����������
��������������������������
�������������������������
Understanding the Controls (Refer to the Fig.3)
1.
� �
�������������
��������������
������������������
�������������������
����������������
������������������������
�����������������
���������������
����������������
Direct the sensor toward the desired area to be
scanned by adjusting the swivel joint on the sensor
arm.
Important: loosen the lock nuts and screws
on sensor and floodlight before making any
adjustments.
TIME SENS
LUX
2.
Have another person move across the centre of the
area to be scanned
and slowly adjust the angle of
��������������
�������������
the sensor arm until the unit sensors the presence
of the moving person, causing the floodlight to
switch on (refer Fig. 1B).
�������������������
3.
Adjust time control to required setting.
4. To set the light level at which the floodlight will
automatically switch “on” at night, turn the LUX
Adjusting the duration time: The length of time that
control knob from daylight ( ) to night ( ). If the
the light remains switched on after activation can
floodlight is required to switch on earlier, e.g. dusk,
be adjusted from (10±5) seconds to (4±1) minutes.
wait for the desired light level, then slowly turn the
Rotating the TIME knob anti-clockwise will reduce the
LUX control knob �������
towards daylight while someone
duration time. Note: Once the light has been triggered
���� of the area to be detected.
walks across the centre
by the PIR sensor any subsequent detection will start the
When the floodlight switches on, release the
���������
timed period again from the beginning.
������LUX control knob. You may need to make further
adjustments to achieve your ideal light level setting
��
��
���
Adjusting the lux control level: The Lux control module
has a built-in sensing device (photocell) that detects
Specifications
daylight and darkness. Rotating the LUX knob clockwise
������������������������
is from light ( ) to dark ( ). The ( ) position denotes
Detection Range: Max. 12 meters at approx. 180° scan
that the Floodlights can work at day and night and the
(see notes above)
( ) position only work at night. You can set to operate
Duration Time Adjustment: (10±5) secs to (4±1) mins
the unit at the desired level by adjusting the LUX knob.
Detection Circuitry: Passive Infra-Red (PIR)
4W Consumption (sensor head only)
Weatherproof: IP44
Adjusting the sensitivity: The sensitivity means the
Power Required: 220-240V~ 50 Hz
maximum distance at which PIR sensor can be triggered.
Maximum Load: E27;1x24W CFL Energy saving lamp
Turning the SENS knob anti-clockwise will decrease the
Recommended power supply cable: H05RN-F 3G
sensitivity
1.0mm2
Protection: Class I
Setting the controls: Turn the Lux control knob to light
Unit Dimension: 222(L) x 133(W) x 234(H) mm
( ) position, turn the wall switch on and wait half a
minute for the control circuit to stabilize. At this stage
ensure that the TIME control knob is set at minimum
Safety Markings
duration time (-) position (Rotating the TIME knob anticlockwise to stop-position). The floodlight will now
IP44
switch on and remain on for about 30 seconds (within
60 seconds).
4
Installation Instructions & Care
Cleaning
To avoid dust build-up and ensure proper functioning of
the floodlight, please wipe the sensor lens lightly with a
damp cloth every 3 months.
3.
Remove the lamp. Pull directly out of lampholder,
do not twist.
4.
Insert new lamp.
5.
Replace the diffuser and secure in position making
sure that the gasket is correctly positioned and
compressed.
6.
Restore the power and switch on.
Disconnect the power and clean the exterior only of this
fitting with a moist (not wet) cloth.
Do not use any chemical or abrasive cleaners.
Replacement Lamp Type
Lamp Replacement
Wattage: 24W
Type: 24W ES Helical CFLi
1.
Switch off the electricity at the mains.
2.
Using a cross-headed screwdriver, loosen the screws
and lift off the diffuser.
This fitting is designed for low energy compact
fluorescent lamps, do not use incandescent or halogen
lamps.
Trouble Shooting & User Hints
Problem
Possible Cause
Suggested Solutions
Light does not switch on when
there is movement in the
detection area
1. No mains voltage
2. Bulb - faulty/missing
3. Light nearby is too bright
4. Controls set incorrectly
5. Sensor postioned in wrong direction
• Check all connections, fuses and switches
• Check. Replace
• Redirect sensor or relocate the unit
• Readjust sensor angle or control knob
• Redirect sensor and/or adjust
Lamp switches on for no
apparent reason (false trigger)
1. Heat from lamp body activating sensor
• Adjust PIR sensor or floodlight to allow a
minimum gap 40mm between floodlight
body and sensor head
2. Heat sources i.e; air-con, vents, heater flues,
bbq’s, outside light, moving cars can activate
sensor
• Adjust direction of sensor head away from
these sources
3. Animals or birds e.g. possums or domestic
animals
• Redirecting sensor may help
4. Interference from on/off switching of
electric fans, lights on the same circuit as
your security floodlight. (This problem does
not always occur but a faulty switch or noisy
fluorescent light may cause the security
floodlight to switch on
• Should the false triggering become,
troublesome, consider:
(a) Replacing a faulty switch.
(b) Replacing noisy fluorescent tubes/starters
(c) Connecting the floodlight to a separate
circuit (in most cases where one or more
of the above suggestions have been
carried out, false triggering has been
reduced)
5. Reflection from swimming pool or reflective
surface
• Relocate the fitting
Light remains on
1. Continuously false triggered
2. Time to set too long
• Redirecting sensor head may help
• Reduce time
Light switches on during daylight
hours
1. LUX control knob is set to daylight position
• Turn the LUX control knob to desired light
level setting
When setting lux controls in
daylight the detection distance
becomes shorter
1. Interference by sunlight
• Re-test at night
Note: All passive infra red detectors are more sensitive in cold and dry weather than warm and wet weather.
5
Eventually, you may want to replace this light fitting
When your light fitting comes to the end of its life or you choose to update or upgrade it by replacing it, please do
not dispose of it with your normal household waste, please recycle where facilities exist. When you need to dispose
of this fitting, check with your retailer or local authority for suitable options. New regulations require the recycling
of Waste from Electrical and Electronic Equipment (European “WEEE Directive” effective August 2005—UK WEEE
Regulations effective 2nd January 2007). Environment Agency Registered Producer: WEE/GA0248QZ
If your light is defective or develops a fault, please return it to the place where you bought it. You can call our
Helpline for advice. The Helpline will gladly give advice on any aspect of any Eterna Lighting product but may not
be able to give specific instructions regarding individual installations.
If in doubt, consult a qualified electrician.
Help Line
Tel: 01933 673 144
Fax: 01933 678 083
Email: [email protected]
For all other information visit our website www.eterna-lighting.co.uk
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement