Contact Details Please note that some of the contact

Contact Details Please note that some of the contact
 Contact Details Please note that some of the contact details on this PDF document may not be current. Please use the following details if you need to contact us: Telephone: 0844 879 3588 Email: [email protected] The customer support section of our website also features a wide range of information which may be of use to you and is available 24 hours a day. It includes: • Operating and installation instructions • Easy ‘How to use’ guides for storage heaters • Service and repairs • Where to buy our products • Literature downloads • Heating requirement calculator Visit ‐ www.dimplex.co.uk/support A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.dimplex.co.uk
Registered No: 1313016 England
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources
Installation and Operating Instructions
Dimplex Convector Heaters
INDCUKDX2R
Issue 5
Models : DX200, DX200S, DXW200S, DX200T,
DX300S, DX300T and DX300TF.
Dimensions
(millimetres)
Model(s)
450
MIN
Specification
230
697 - 3.0kw
577 - 2.0kw
MIN
DX200
DX200S
DXW200S
DX200T
DX300S
DX300T
DX300TF
2.0kw + Thermostat
2.0kw + Thermostat + Switch
2.0kw + Thermostat + Switch (Wall Mtd.)
2.0kw + Thermostat + 24hr Timer
3.0kw + Thermostat + 2 Switches
3.0kw + Thermostat + 24hr Timer
3.0kw + Thermostat + 24hr Timer + Turbo
230
156
MIN
357
432
230
MIN
Floor Mtd.
Wall Mtd.
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
IMPORTANT SAFETY ADVICE
WARNING –THIS APPLIANCE MUST NOT BE USED IN A BATHROOM
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL.
WARNING – THIS HEATER MUST NOT BE LOCATED IMMEDIATELY
BELOW A FIXED SOCKET OUTLET.
DO NOT USE THE HEATER UNTIL THE FEET OR WALL BRACKETS
ARE FITTED CORRECTLY.
FOLLOW these instructions carefully.
NEVER cover or obstruct in any way the heat outlet slots at the top
of the heater or the air inlet slots in the base of the heater.
The heater carries a warning ‘DO NOT COVER’ to alert the user to the
risk of fire that exists if the heater is accidentally covered.
Models DX200T, DX300T, DX300TF can be set to switch on
automatically. Remember to observe all safety warnings at all times.
This appliance is not intended for use by children or other persons
without assistance or supervision if their physical, sensory or mental
capabilities prevent them from using it safely. Children should be
supervised to ensure that they do not play with the appliance.
If young children, the aged or infirm are likely to be left in the vicinity
of the heater, we advise that adequate precautions should be taken.
We recommend that a guard be fitted to ensure contact with the
heater is avoided and objects cannot be inserted into the product.
If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
For further information, please contact our guard supplier direct on
Tel. No. 01603 667957, or in case of difficulty or for further advice
contact the Customer Helpline.
Warning : In order to avoid a hazard due to inadvertent resetting of
the thermal cutout, this appliance must not be supplied through an
external switching device, such as a timer, or connected to a circuit
that is regularly switched on and off by the utility.
Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK.
This appliance must only be used on A.C. mains supply of 230/240
Volts~.
Wall Mounting
Three identical wall mounting brackets are secured to the base of the
heater with a fixing screw. To wall mount appliance, first remove the
brackets as follows :
Lay the heater on its back.
Following the sequence in Fig. 1 – identify and remove the fixing screw
securing the brackets located beside Mains Cable as shown in (A), then
pull out brackets and rotate them to disengage them from the slot (B).
Withdraw the brackets from the slot (C).
(A)
(B)
(C)
Fig. 1
Select a suitable position on a wall, near to a mains power socket,
making sure that there is at least 230 mm below the heater and at least
450 mm above the heater of unobstructed space. See also ‘Positioning
the heater’.
Fix the two top retaining brackets to the wall, using suitable fixings, for
2kw models at 358 mm centres and 3kw models at 478 mm centres –
see Fig 2.
centres
2kw - 358mm
centres
3kw - 478mm
shelf /
ceiling
526 mm
min.
bracket
slot
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage marked
on the heater must correspond to the supply voltage. If fitting a 13 amp
plug, a 13 amp fuse approved by ASTA to BS 1362 must be used. If any
other type of type of plug is used, a 15 amp fuse must be fitted in the plug,
the adaptor, or at the distribution board.
IMPORTANT - The wires in the mains lead are coloured in accordance
with the following code:
GREEN and YELLOW
BLUE
BROWN
-
EARTH
NEUTRAL
LIVE
Connect the GREEN AND YELLOW wire to the terminal marked ‘E’ or by
the earth symbol
, or coloured GREEN or GREEN AND YELLOW.
Connect the BROWN wire to the terminal markef ‘L’ or coloured RED.
520 mm
min.
3 No. Wall
Mounting
Brackets
floor
Fig. 2
Locate the heater on the top brackets and allow it to hang in place.
Fit the bottom bracket into the slot in the heater and then fix it to the wall.
Test that the heater is now securely fixed to the wall.
Positioning the heater
Always ensure that the heater is stood on a firm, level base near to, but
not directly beneath, a suitable mains supply socket.
Ensure that curtains and furniture are not positioned close to the chosen
position, as this would create a potential fire hazard.
We recommend that the heater should be wall-mounted in rooms where
children may be left unattended.
See also ‘Important Safety Advice’.
The thermostat also has a frost protection setting marked ‘∗’. This setting
is useful in areas such as garages to prevent frost damage. If the
thermostat is set to its minimum setting ∗, the heater will cycle ON and
OFF to maintain a temperature of approximately 5°C to help protect
against frosty conditions.
Timer Operation
Set the I - ¡ - 0 slide switch on the timer
Fig. 5 to :
Free standing use (all models except DXW200S)
Position O – for Heating Off
Position I – for Manual operation
– This setting allows power to the heater
uninterrupted by the timer settings. The
heat selector switch will control the
output (see ‘Using the heater’).
NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET
FITTED.
Lay the heater on its back, and locate
the foot fixing screw (see a. in Fig. 3).
Remove the screw using an
X–head screwdriver, then align foot
over slots and holes in base (see ‘b’
in Fig. 3) and push into slots until the
foot clips into place.
Position ¡ - for ‘Auto’ operation
Fig. 5
Finally take the foot fixing screw, insert
and tighten using a screwdriver to
secure the foot.
Setting the time of day
Fig. 3
To set the time of day, rotate the timer
dial clockwise (indicated by the arrow)
until the correct time of day is opposite
the reference mark ► (see Fig. 5). The
24-hour clock is used ; e.g. time shown
for 4 pm is ‘16’ (16:00hrs).
NOTE – The wall mounting brackets indicated in Fig. 3 can be left secured
to the base if they are not required.
Using the heater
Fig. 6
Switch on at the wall socket.
Setting the auto ON and OFF times
On models with a neon, the red POWER ON neon will light when the
heater is connected to the power supply.
To set the timer :
The timer clock will operate all the time that the heater is connected to the
mains supply.
Set the timer control switch as required
for OFF, Manual or Automatic
operation – see ‘Timer Operation’.
On models DX200S , DXW200S &
DX300S the heat selector switch
positions are as follows :
I - Low heat output
II - High heat output
On model DX300S there is also an
On – Off switch - operation as follows :
O - Off
I - On
DO NOT disconnect this heater from the
mains supply unless it is being taken out
of use (e.g. in summer or for storage),
otherwise the timer clock will stop.
Fig. 7
1. Using your finger tip or the tip of a
pencil, push in as many segments as
necessary around the dial, according to
the times you don’t require heat – see
Fig. 7. Each segment pushed in switches
the heater OFF for that part of the hour.
All other segments will be ON. For
example, Fig. 9 shows the timer set to
switch the heater ON between 7 am and
9 am and between 4 pm and 9.30 pm .
2. You can select as many ON periods
as you like, within the 24-hour day. The
settings will repeat every day until
changed.
Fig. 4
(Model DX200T , DX300T
& DX300TF control shown)
3.
To change ON and OFF times,
simply push in any ‘ON’ segments you
wish to cancel and pull out new ON
segments as required.
The heat output is controlled by the thermostat - see ‘Thermostat’
Please note – the element has been coated with a protective film which
will burn off during the first few minutes of use and may cause a small
amount of fuming. This is quite normal – the fumes are non-toxic and will
quickly disappear. We recommend that you open a window to ventilate the
room when using the heater for the first time.
Switching to ‘Auto’
Fig. 8
Controls
Thermostat
The thermostat controls the heat output according to the room
temperature.
This ensures that the heater will not produce heat unnecessarily when the
room is warm.
To set the temperature you require, turn the thermostat knob clockwise
until the desired temperature is reached. Alternatively to heat a cold room
quickly, turn the thermostat knob up fully.
When the room has reached the desired temperature, turn the thermostat
knob anti-clockwise until the thermostat just clicks off.
The heater will now automatically operate at this temperature.
Set the heat selector and thermostat for
the heat output required.
Check that the clock shows the correct
time of day. Set the I - ¡ - 0 slide switch
to position marked ¡ (see Fig. 8) the convector will switch ON and OFF
according to the timer settings (see
Fig 9).
IMPORTANT NOTES
Fig. 9
Remember to observe all safety
warnings when operating the heater on
auto setting unattended or attended . . If
the mains supply to the heater is
interrupted, the timer clock will stop until
power is restored ; reset the time of day
to ensure correct ON and OFF times.
Turbo Fan model (DX 300TF)
The turbo fan is used to boost the airflow around the room. The fan will
circulate the heat around the room to reach the desired temperature more
quickly.
On this model once power is supplied to the heater & the timer is in an on
position the heater can be set to run on 2kW output by setting the turbo
switch in its off position ( neon off ). For 3kW output you turn the turbo
switch to it’s on position (neon on) to introduce an additional 1kw of heat
with fan boost which added to the 2kW setting will give a total output of
3kW with fan boost. ( Note: on this model turbo boost is only possible on
3kW operation).
Note: there is no cold blow operation on this model and all heat settings
operate under the control of the thermostat.
Fig. 10
Turbo Model – DX300TF
Recycling
For electrical products sold within the
European Community.
At the end of the electrical products useful life
it should not be disposed of with household
waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for
recycling advice in your country.
Safety – overheat protection
Cleaning and User Maintenance
For your safety, this appliance is fitted with a thermal cut-out. In the event
that the product overheats, the cut-out switches the heater off
automatically.
To bring the heater back into operation, remove the cause of the
overheating, then unplug or turn off the electrical supply to the heater for a
few minutes.
When the heater has cooled sufficiently, re-connect and switch on the
heater.
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of any kind on
the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust and a
damp cloth (not wet) to clean off stains. Be careful not to allow moisture
into the heater.
After Sales Service
Important Notes
Although this heater is manufactured to comply with the relevant safety
standards, certain types of carpets could become discoloured by the
temperatures under a portable heater. If you are concerned about this, we
recommend that you contact the carpet manufacturer for guidance.
Alternatively, either stand the heater on a suitable base to shield the
carpet or wall-mount it – call our Helpline for further advice.
You may notice some parts of the element appearing to be hotter from
time to time because of the variable airflow through the heater. This does
not cause a safety hazard.
The heat outlet grille may become discoloured with use – this is caused by
airborne pollution and is not a fault.
Your product is guaranteed for three years from the date of purchase.
Within this period, we undertake to repair or exchange this product free
of charge (excluding element & subject to availability) provided it has
been installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0870 727 0101. It would assist us if you can quote
the model number, series, date of purchase, and nature of the fault at the
time of your call. The customer services help desk will also be able to
advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a
satisfactory service.
Please retain your receipt as proof of purchase.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Services:
Republic of Ireland
Tel.
Fax.
e-mail
Tel.
0870 7270101
0870 7270102
[email protected]
01 8424833
[c] Glen Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement