FireplaceXtrordinair 42 Apex Clean Face Owner's Manual
Advertisement
Advertisement
42 Apex Owner’s Manual
SAFETY NOTICE:
If this appliance is not properly installed, a house fire may result.
For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.
12521 Harbour Reach Drive
Mukilteo, WA 98275
This manual is available online in French
Ce manuel est disponible en ligne en Français
Copyright 2016, T.I.
$10.00 100-01437 www.travisproducts.com
Tested and listed by
Report # 028WF102S
Tested to: U.L. 127-2015, ULC-610-M87 (R1998)
2
Introduction
Introduction
We welcome you as a new owner of a Fireplace Xtrordinair wood fireplace. In purchasing a Fireplace
Xtrordinair you have joined the growing ranks of concerned individuals whose selection of an energy system reflects both a concern for the environment and aesthetics. The Fireplace Xtrordinair is one of the finest home heaters the world over. This manual will explain the installation, operation, and maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your heater and save the manual for future reference. Included are helpful hints and suggestions which will make the operation and maintenance of your new fireplace an easier and more enjoyable experience. We offer our continual support and guidance to help you achieve the maximum benefit and enjoyment from your heater.
SERIAL NO:
Tested and
Listed by
Report No. 028WF102S
Certified for USA and Canada
DO NOT REMOVE THIS LABEL
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT INSTALLATION AND RESTRICTIONS IN YOUR AREA.
LISTED FACTORY-BUILT FIREPLACE
CONFORMS TO UL STD 127-2015; CERTIFIED TO ULC STD S610-M87 (R1998)
®
MODEL:
42 Apex
This wood heater needs periodic inspection and repair for proper operation. Consult the owner’s manual for further information. It is against federal regulations to operate this wood heater in a manner inconsistent with operating instructions in the owner’s manual or if the catalytic element is deactivated or removed. CAUTION: the combustor used in this appliance (part no. 250-00556) is fragile and must be handled carefully. Burning of metal foils, plastic, garbage, sulphur and diesel oil will render the catalyst in the combustor inactive. The performance and durability of the catalytic combustor has not been evaluated as part of the certification. Do not use a fireplace insert or other products not specified for use with this product. This fireplace has not been tested with an unvented gas log set. To reduce the risk of fire or injury, do not install an unvented gas log set into fireplace. Fireplace must use combustion air drawn from outside the house. Use cord wood only. DO NOT OVERFIRE UNIT.
Approved chimney: Simpson Duravent 7”Duravent DuraPlus HTC & Simpson Duravent 8”X12” sold through Travis Industries
Replace glass only with 5mm neoceramic or ceramic glass.
Electrical Rating: 115V., 60 Hz, 1.8 Amps
Optional Green Start: # 94400954
Blower: # 250-04176
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with 2015 particulate emission standards. Not approved for sale after May 15, 2020.
0.7 g/h, Method 28, 5G2, 2015
Manufactured by:
TRAVIS INDUSTRIES, INC.
12521 Harbour Reach Drive
Mukilteo, WA 98275 www.travisproducts.com
Made in U.S.A.
2016 2017 2018 2019 Jan Feb
DATE OF MANUFACTURE
Mar Apr May Jun Jul Aug Sep Oct Nov Dec
42 APEX
OWNER’S MANUAL
1212
42 Apex
This wood heater contains a catalytic combustor which needs periodic inspection and replacement for proper operation.
Consult the owner’s manual for further information. It is against federal regulations to operate this wood heater in a manner inconsistent with operating instructions in the owner’s manual or if the catalytic element is deactivated or removed. See installation and operating instructions for this model. Use cord woood only.
XXXX
®
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with 2015 particulate emission standards. Not approved for sale after May 15, 2020.
0.7 g/h, Method 28, 5G2, 2015
M a n u f a c t u r e d B y : T R AV I S I N D U S T R I E S , I N C .
1 2 5 2 1 H a r b o u r R e a c h D r i v e , M u k i l t e o , WA 9 8 2 7 5
2016
2017
2018
MANUFACTURE DATE:
JAN
FEB
MAR
Serial
No.
APR
MAY
JUN
ZC-1203
JUL
AUG
SEP
OCT
NOV
DEC
Important Information
No other Fireplace Xtrordinair wood fireplace has the same serial number as yours. The serial number is behind the left side door just inside the firebox.
This serial number will be needed in case you require service of any type.
Model:
Serial Number:
Purchase Date:
Purchased From:
Mail your Warranty Card Today, and
Save Your Bill of Sale.
To receive full warranty coverage, you will need to show evidence of the date you purchased your heater. Do not mail your
Bill of Sale to us.
We suggest that you attach your Bill of
Sale to this page so that you will have all the information you need in one place should the need for service or information occur.
© Travis Industries 4161018 100-01437
Table of Contents
Introduction ............................................................................................................................................... 2
Important Information ................................................................................................................................ 2
Features: ................................................................................................................................................... 6
Heating Specifications .............................................................................................................................. 6
Electrical Specifications: ........................................................................................................................... 6
EPA Compliance: ...................................................................................................................................... 6
Safety Notice: ............................................................................................................................................ 7
Before Your First Fire ................................................................................................................................ 7
Verify the Installation ............................................................................................................................ 7
Curing the Paint .................................................................................................................................... 7
Over-Firing the Fireplace (Over-Firing may void your warranty) ......................................................... 7
Operating the Fireplace During a Power Outage ................................................................................. 8
Drafting Performance ........................................................................................................................... 8
Location of Controls .................................................................................................................................. 8
Opening the Door ...................................................................................................................................... 9
Opening the Door While the Fireplace is Hot ....................................................................................... 9
Starting a Fire ............................................................................................................................................ 10
Maintaining Catalytic Burn-Off .................................................................................................................. 11
Adjusting the Burn Rate ............................................................................................................................ 12
Electrical Controls ..................................................................................................................................... 13
Understanding Your Heater’s Combustion System .................................................................................. 14
Burning Your Heater ................................................................................................................................. 14
Re-Loading the Fireplace .......................................................................................................................... 15
Overnight Burn .......................................................................................................................................... 15
Normal Operating Sounds ........................................................................................................................ 15
Hints for Burning ....................................................................................................................................... 15
Ash Removal ............................................................................................................................................. 16
Selecting Wood ......................................................................................................................................... 16
Dry Wood is Key ................................................................................................................................... 16
Testing Wood Moisture ........................................................................................................................ 16
Why Dry Wood is Key .......................................................................................................................... 16
Wood Cutting and Storage ................................................................................................................... 17
Don't Burn Treated Wood, Wax Logs, Coal, Garbage, Etc. ................................................................. 17
Check Firebrick, Baffle ......................................................................................................................... 19
Clean the Combustor ........................................................................................................................... 19
Chimney Sweep Instructions ................................................................................................................ 19
Door and Latch Inspection and Service .................................................................................................... 20
Testing the Door Seal ........................................................................................................................... 20
Fixing the Door Seal ............................................................................................................................. 20
Clean the Glass (if necessary) .......................................................................................................... 21
Creosote – Formation and Need for Removal ..................................................................................... 21
Replacement Parts List ............................................................................................................................. 22
Door Parts ............................................................................................................................................ 22
Electrical Parts...................................................................................................................................... 22
Firebox Parts ........................................................................................................................................ 23
Years 1 & 2 - COVERAGE: PARTS & LABOR ......................................................................................... 24
One-way freight allowance on pre-authorized repair done at factory is covered. ................................ 24
Years 3 Through 5 - COVERAGE: PARTS & LABOR .............................................................................. 24
Years 6 & 7 - COVERAGE: PARTS ONLY ............................................................................................... 24
CONDITIONS & EXCLUSIONS ................................................................................................................ 24
IF WARRANTY SERVICE IS NEEDED: ................................................................................................... 24
GreenStart™Woodstove Igniter (Part # 94400951) ................................................................................. 25
© Travis Industries 4161018 100-01437
3
4
ASHES
Table of Contents
• This fireplace must be installed by a qualified installer. Installation instructions are shipped inside the fireplace and must be strictly adhered to.
Ok
• Contact your local building officials to obtain a permit and information on installation restrictions or inspection requirements in your area. Notify your insurance company of this fireplace.
• This fireplace is designed and listed for cord wood only. Burning of any other material will void the warranty and listing and may create a fire hazard.
• The door(s) must be closed and latched during operation. Open the door(s) only when reloading the fireplace or conducting maintenance.
This prevents smoke, embers from entering the room.
• Ashes must be disposed of in a metal container with a tight fitting lid.
Place the container on a non-combustible surface until the ashes have fully cooled before final disposal.
• If you smell smoke, see the section "Smoke Smell in Home" on page 13 of this manual for a remedy.
36"
Gas
• Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or ‘freshen up’ a fire in this fireplace. Keep all such liquids well away from the fireplace while it is in use.
• Do not touch the hot surfaces of the fireplace.
Educate all children of the danger of a hightemperature fireplace.
Young children should be supervised when they are in the same room as the fireplace.
• Keep all furniture or other combustible items at least
36" away from the front of the fireplace (this includes drapes or doors that may swing within 36" of the front of fireplace).
• Do not place clothing or other flammable items on or near the fireplace.
• Never block free airflow through the vents.
© Travis Industries 4161018 100-01437
Safety
5
Do not repair, alter, or replace any part of the fireplace and chimney unless instructions are give in this manual. All other work must be done by a qualified service person.
Allow the fireplace to cool before carrying out any maintenance or cleaning.
The chimney must be inspected twice a year for creosote build-up or chimney damage. Creosote build-up must be removed and damage fixed prior to using the fireplace.
This
Manual
Do not throw this manual away.
This manual has important operating and maintenance instructions that you will need at a later time. Always follow the instructions in this manual.
This fireplace was designed to burn solid wood fuel only
(cord wood). Never use treated wood, wax logs, coal, garbage, or other materials.
These materials will void the safety listing and may damage the combustor.
This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating instructions in this manual.
Travis Industries, Inc. grants no warranty, implied or stated, for the installation or maintenance of your fireplace, and assumes no responsibility of any consequential
damage(s).
Do not use a grate or other device to elevate the fire off of the firebox floor. Burn the fire directly on the firebox floor.
Smoke and CO Detectors: Make sure your home has a working smoke detector, especially near any bedrooms. We recommend having a smoke and/or CO detector in the same room as the wood heater for additional safety.
Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6
Travis Wood Burning Fireplaces, Stoves and Inserts are protected by one or more of the following patents; U.S. 9,170,025
4,665,889 as well as other U.S. and Foreign Patents pending.
© Travis Industries 4161018 100-01437
6
Specifications
Features:
• Maximum Log Length of 24"
• Large firebox capacity – 3.5 cu. ft.
• Long burn time – up to 12 hours
• Large glass door for maximum visibility
• Full firebrick lining for firebox protection
Heating Specifications
Approximate Heating Capacity
(
Will vary with the home's floor plan, insulation, and outside temperature.)
Maximum Burning Time
BTU Output per Hour (Cord Wood Method)
Up to 2,500 Square Feet
Up to 12 Hours
Up to 62,000 BTUs
This model was tested for efficiency using method B415.1-10 and was determined to have:
Weighted average higher heating value (HHV) overall heating efficiency (OHE) of 73%
Weighted average lower heating value (LHV) overall heating efficiency (OHE) of 78.6%
Maximum measured lower heating value (LHV) efficiency of 83.3%
The location of your wood heater in your home will decide how affectively the heat produced will spread throughout your house. Attention to the home design with consideration of natural convection and air circulation should be taken into account when choosing the placement of your heater within the home.
Electrical Specifications:
The blower on "HIGH" draws 1.8 Amps on 120 Volts A.C. (approximately 130 watts).
EPA Compliance:
This heater meets the 2015 U.S. EPA’s crib wood emission limits for wood heaters sold after May 15,
2015. Tested to Method 28, 5G2 this heater has been shown to deliver 11,000 to 38,000 BTUs/hr and an emission value of .69 g/h.
© Travis Industries 4161018 100-01437
Operation
7
Safety Notice:
• If this appliance is not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.
• Read and follow all of the warnings on pages 2 and 3 of this manual.
Before Your First Fire
Verify the Installation
Before starting the fireplace, verify that the fireplace is properly installed and all of the requirements in the 42 Apex Installation Manual have been followed.
Keep all flammables 36" away from the front of the fireplace (drapes, furniture, clothing, etc.).
A fireplace insert shall not be installed in a factory-built fireplace unless tested with the fireplace.
Curing the Paint
Follow the steps below to cure the paint (first fire): a) Open doors and windows in the room to ventilate the heater during the curing process. b) Vacate the room. The fumes from the initial heating process are non-toxic but may be unpleasant. c) Slowly bring the heater to a medium burn (400°F/204°C) for 45 minutes. Then increase the burn temperature to a hot burn
(600°F/315°C) for an additional 45 minutes. This will cure the paint.
Door Gasket - The door gasket can adhere to the paint on the front of the heater. To prevent this, carefully open and close the door a few times during the paint curing process.
2 to 4 hours
Carbon Monoxide (CO) Emissions
Smoke from wood heaters contain CO. This gas is an indication of incomplete combustion and is detrimental to the environment and to your health. The more visible the smoke, the higher the CO levels. Burning dry wood is the most significant step you can take to reduce CO emissions. It is also important to understand the combustion process so you can burn your heater efficiently. Read the manual thoroughly so that you can operate your heater in the most efficient and clean manner possible.
Over-Firing the Fireplace (Over-Firing may void your warranty)
DO NOT OVERFIRE THIS HEATER: Attempts to achieve heat output rates that exceed heater design specifications can result in permanent damage to the heater.
This fireplace was designed to operate at a high temperature. But due to differences in vent configuration, fuel, and draft, this appliance can be operated at an excessive temperature. If the area behind the faceplate or other area starts to glow red, you are over-firing the fireplace (this may damage the internal components and void the warranty). Do not burn excessively large fires for a long time. Shut the air control down and allow the fireplace to cool if you detect over-firing.
© Travis Industries 4161018 100-01437
8
Operation
Operating the Fireplace During a Power Outage
This fireplace includes a blower to dissipate heat from the firebox. During power outages build small to medium-sized fires to prevent the fireplace from overheating.
Drafting Performance
Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your chimney depends on the length of the chimney, local geography, nearby obstructions and other factors. Too much draft may cause excessive temperatures in the appliance and may damage the heater. Inadequate draft may cause backpuffing into the room and `plugging' of the chimney.
Inadequate draft will cause the appliance to leak smoke into the room through appliance and chimney connector joints. An uncontrollable burn or excessive temperature indicates excessive draft.
WARNING: THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED GAS LOG SET. TO
REDUCE RISK OF FIRE OR INJURY, DO NOT INSTALL AN UNVENTED GAS LOG SET INTO
THIS FIREPLACE.
Location of Controls
Bypass
Door Handle
Air Control
Tool
Bypass – This controls the bypass. When open (pulled out), smoke travels directly up the chimney, lessening the chance of smoke spillage.
Door Handle – The door handle locks the door shut.
Air Control - This control slides left to right (or anywhere between) to alter the amount of air entering the fireplace. This, in turn, regulates the speed at which the fire burns. When slid to the right, the air control is open (fast burn). When slid to the left, the air control is closed (slow burn).
Tool – The fireplace tool is used to help open the door or slide the bypass in or out.
© Travis Industries 4161018 100-01437
Operation
9
Opening the Door
To open the door, lift the handle and swing the door open. Use the included tool if needed to lift the handle.
Do not slam door when closing. If glass is damaged it must be replaced before using the fireplace.
Opening the Door While the Fireplace is Hot
Open (pull out) the bypass before opening the door. This allows smoke to exit the flue directly. Use the included tool, if necessary to pull the bypass out.
To lessen smoke spillage, open the door a few inches, let air enter the door for a few seconds, then open the door fully. This allows airflow inside the firebox to stabilize.
Warning: Do not build the fire close to glass.
Warning: The door handle is extremely hot during operation
– use the door tool or gloves when opening the door.
© Travis Industries 4161018 100-01437
10
Operation
Starting a Fire
Since the dawn of time man has debated the best way to start a fire. Some use the boy-scout "teepee", some prefer the "tic-tac-toe" stack. Either way, review the hints and warnings below to ensure proper fire starting.
• Make sure the by-pass is open while starting a fire (leave it open for the first 15 minutes).
Use the included tool to operate the bypass.
Bypass Pulled Out
Used for starting and re-loading
Bypass Pushed In
Used for normal operation
• Make sure the air control is on high. If additional air is needed, open the doors 1/4" during the first five minutes of start-up.
• If the smoke does not pass up the chimney, ball up one sheet of newspaper, place it in the center of the smoke shelf and light it. This should start the chimney drafting (this eliminates "cold air blockage").
• Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or "freshen up" a fire in this fireplace. Keep all such liquids well away from the fireplace while it is in use.
• If using a firestarter, use only products specifically designed for fireplaces - follow the manufacturer's instructions carefully.
• Use plenty of kindling to ensure the fireplace reaches a proper temperature. Once the kindling is burning rapidly, place a few larger pieces of wood onto the fire.
© Travis Industries 4161018 100-01437
Operation
11
Maintaining Catalytic Burn-Off
Warning:
The bypass control becomes hot during operation - use gloves or a tool to prevent burns.
This fireplace uses a catalytic combustor to increase heat transfer to the room and reduce emissions.
The catalytic combustor takes dirty smoke and turns it into extra heat and cleaner emissions.
NOTE: If the combustor is engaged
(bypass closed) when the fireplace is still cool, it will not work, leading to dirty smoke, no extra heat, and a dirtier combustor.
Follow the directions below to utilize the combustor to its fullest potential.
• Keep the by-pass open (pulled out) until the fireplace becomes hot (approximately 15 to 30 minutes).
• Close the by-pass (push in) when the fireplace is hot (500° F./260° C. or greater).
• Keep the by-pass closed (pushed in) while the fireplace is operating, except when re-loading.
With the by-pass open (pulled out), the smoke passes through the by-pass and does not go through the combustor.
With the by-pass closed (pushed in), the smoke passes through the combustor.
Chimney
Combustor
By-Pass
Plate
Sm oke
Sm oke
By-Pass Control
Sm oke
Sm oke
How to Check if your Combustor is Working
A combustor temperature probe is included with the fireplace to monitor the combustor. After the bypass is engaged, the combustor temperature should rise, showing combustor operation. Combustor temperatures over 500° F (260° C), indicate the combustor is working and igniting unburnt fuel.
The combustor can also be viewed through the glass from below. You will notice the combustor glowing red when the combustor is working effectively.
© Travis Industries 4161018 100-01437
12
Operation
Adjusting the Burn Rate
Use the air control slider to control the burn rate of the fireplace. See the illustration below for details.
The included tool may be used to adjust the air control when the fireplace is hot.
Warning: The air control becomes hot during operation - use gloves or the tool to prevent burns.
Hint: The air control may take several minutes to influence the burn rate. When making adjustments, you may wish to let the fireplace burn for 10 minutes to gauge performance.
Hint:
The blower may be used to affect heat output (i.e.: to reduce heat output, turn the blower down).
© Travis Industries 4161018 100-01437
Operation
13
Electrical Controls
Blower Speed Control
Set the blower speed using this control.
NOTE: The blower will not turn on until the fireplace is up to temperature.
Combustor Temperature
Press this button to see the combustor temperature.
Optional GreenStart Igniter press this button to start the ignition sequence.
NOTE: The button will not be visible if GreenStart is not installed - see GreenStart instructions for details.
© Travis Industries 4161018 100-01437
14
Operation
Understanding Your Heater’s Combustion System
This heater uses a dual combustion system detailed below:
Primary Combustion: This is the combustion (fire) that takes place directly on the wood. Primary combustion determines how fast the fire burns. Air for primary combustion is supplied through the air control. When you adjust the air control you control the amount of air that reaches the fire and creates primary combustion. The air control supplies air to the air wash (the air holes above the door opening – used to help clean the glass) and through the pilot orifice (center bottom of the door opening). By using the air control, and supplying air through these two openings, you control primary combustion.
Catalytic Combustion: This is the combustion (fire) that does not contact the wood. Catalytic combustion takes place inside the catalytic combustor and is not viewable (you may, however, see the combustor glow). It burns the visible emissions or smoke that is not consumed during primary combustion. Catalytic combustion can be monitored by using the included temperature meter. Your catalytic combustor is working when the out put temperature is above 500° F. (260°C).
Items to Consider:
During medium and high burn rates the stove will manage combustion on its own. When the heater is set to a low burn rate more care is needed to ensure the catalytic combustion system works properly. Make sure the stove is hot and a good coal bed is established before adjusting your heater to low burn.
Understanding the combustion system in this heater will help minimize the visible emissions this heater releases into the environment. The primary pilot orifice at the center bottom of the door opening is designed to help the secondary combustion at low burn settings. The pilot provides a small amount of air that burns up through the fuel load providing the heat and flame needed for the secondary system to ignite.
As you load your heater for a low burn, take care in placing the wood. This will affect how well your catalytic system works as the wood is consumed. Do not block the pilot orifice. Stack wood so the pilot air can burn its way up between the pieces, helping your heater burn effectively throughout the low fire. This will reduce the visible emissions your heater produces and increase the amount of heat you get from the wood. If you are unsure how well your heater is burning look at the chimney cap to monitor visible emissions.
Burning Your Heater
Starting a Fire: When starting a fire it is imperative to get the heater hot and drafting as quickly as possible.
This promotes combustion and reduces emissions. There are many ways to start a fire and you will become adept as you become familiar with the way your heater burns. Before you start, make sure your burn rate setting
(air control) is all the way open and the by-pass (if equipped) is open. We suggest that you use a layer of crumpled newspaper covered with three layers of small kindling, stacked tic tac toe style with approximately ½”-
1”gaps between them. Continue to layer wood on top of the kindling with the same air gaps using slightly bigger pieces increasing in size as you stack upward with the final layer being 3-5” diameter pieces loaded on the top.
This should fill the firebox. Light the newspaper in several places near the door opening. Shut the door but do not latch it, creating a small opening to allow air to feed the kindling fire. Never leave your heater unattended if your door is not latched shut. While the kindling burns the fire will heat and ignite the larger pieces above. Once the whole load is burning shut and latch the door leaving the burn rate on high. Depending on your heater, the chimney, and the outside environment, you may need to leave your bypass open for up to 20 minutes after lighting the fire. If the fire dies when you shut the bypass you will need to leave it open longer. The presence of a hot coalbed is critical to good combustion. We cannot overstate the importance of a hot coal bed before slowing your burn rate or re-loading your heater. We recommend that you allow the first ignition load of wood to burn through at the high burn rate. This will get your heater up to temperature and establish a coal bed.
Reloading: When reloading a hot heater set the burn rate on high for at least 15 min before slowing it down.
Low Burn: If preparing for an overnight or low burn a longer heat up period may be necessary. Reload the heater full of wood making sure there are air gaps between the wood pieces so the pilot air can burn up through the middle load keeping the secondary combustion system hot and active throughout the burn. After loading, burn the heater on high for at least 15 minutes before setting the air control to low.
© Travis Industries 4161018 100-01437
Operation
15
Re-Loading the Fireplace
Follow the directions below to minimize smoke spillage while re-loading the fireplace.
1
Pull the by-pass out all the way (use the tool or a glove).
2
Move the air control to high.
3
Open the door slightly. Let the airflow inside the firebox to stabilize before opening the doors fully.
4
Load wood onto the fire.
Overnight Burn
This fireplace is large enough to accommodate overnight, 10 to 12 hour burns. Follow the steps below to achieve an overnight burn.
1
Get the fireplace hot by moving the air control to high and letting the fireplace burn for 15 minutes.
2
Load as much wood as possible. Use large pieces if possible.
3
Let the fireplace burn on high for 15 minutes to keep the fireplace hot, then turn the air control to low.
4 In the morning the fireplace should still be hot, with embers in the coal bed. The glass may be dark – this is normal. Stir the coals and load small pieces of wood to re-ignite the fire, if desired.
Note:
Differences if chimney height and draft may lower overall burn times.
Normal Operating Sounds
Creaks and Clicks:
The steel may creak or click when the stove heats up and cools down - this is normal.
Blower Sounds:
The blower will make a slight "humm" as it pushes air through the stove.
Hints for Burning
• Get the appliance hot before adjusting to low burn
• Use smaller pieces of wood during start-up and high burns to increase temperature
• Use larger pieces of wood for overnight or sustained burns
• Stack the wood tightly together to establish a longer burn
• Be considerate of neighbors & the environment: burn dry wood only
• Burn small, intense fires instead of large, slow burning fires when possible
• Learn your appliance's operating characteristics to obtain optimum performance
© Travis Industries 4161018 100-01437
16
Operation
Ash Removal
Whenever ashes get 3 to 4 inches deep in your firebox, and when the fire has burned down and cooled, remove excess ash. Leave an ash bed approximately 1 inch deep on the firebox bottom to help maintain a hot charcoal bed. Let the stove cool completely before removing ashes (wait at least two hours after the last coal has extinguished). Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be placed on a noncombustible floor or on the ground, away from all combustible materials, pending final disposal. The ashes should be retained in the closed container until all cinders have thoroughly cooled.
ASHES
Improperly disposed ashes lead to fires. Hot ashes placed in cardboard boxes, dumped in back yards, or stored in garages, are recipes for disaster.
Wood-burning stoves are inherently dirty. During cleaning have a vacuum ready to catch spilled ash
(make sure ash is entirely extinguished).
There are vacuum cleaners specifically made to remove ash (even if the ash is warm). Contact your dealer for details.
Selecting Wood
Dry Wood is Key
Dry wood burns hot, emits less smoke and creates less creosote.
Wet
Wood
Less
Heat
Leads
To
Dry
Wood
More
Heat
Leads
To
Leads
To
Leads
To
More Smoke and Creostoe
Less Smoke and Creostoe
Testing Wood Moisture
Wood cut, split and stored in a dry area will typically dry within 1 or 2 years. This insures dry wood. If purchasing wood for immediate use, test the wood with a moisture meter. Some experienced wood burners can measure wood moisture by knocking pieces together and listening for a clear "knock" and not a "thud".
Why Dry Wood is Key
Wet wood, when burned, must release water stored within the wood. This cools the fire, creates creosote, and hampers a complete burn. Ask any experienced wood burner and he or she will agree: dry wood is crucial to good performance.
© Travis Industries 4161018 100-01437
Operation
17
Wood Cutting and Storage
Cut wood to length and chop into quarters.
Store the wood off the ground in a covered area. Allow for airflow around the wood to dry the wood.
Air Flow
Air Flow
Air Flow
Don't Burn Treated Wood, Wax Logs, Coal, Garbage, Etc.
This heater is designed to burn natural wood only. Higher efficiencies and lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods. DO NOT BURN:
(1) Garbage;
(2) Lawn clippings or yard waste;
(3) Materials containing rubber, including tires;
(4) Materials containing plastic;
(5) Waste petroleum products, paints or paint thinners, or asphalt products;
(6) Materials containing asbestos;
(7) Construction or demolition debris;
(8) Railroad ties or pressure-treated wood;
(9) Manure or animal remains;
(10) Salt water driftwood or other previously salt water saturated materials;
(11) Unseasoned wood; or
(12) Paper products, cardboard, plywood, or particleboard. The prohibition against burning these materials does not prohibit the use of fire starters made from paper, cardboard, saw dust, wax and similar substances for the purpose of starting a fire in an affected wood heater.
Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.
© Travis Industries 4161018 100-01437
18
Operation
Troubleshooting
Smoke Enters Room During
Start-Up
Kindling Does Not Start -
Fire Smolders
Smoke Enters Room While
Re-Loading
Fireplace Does Not Burn Hot
Enough
Blower Does Not Run
Fireplace Does Not Burn
Overnight
• Cold Air Blockage - burn a piece of newspaper on top of the smoke shelf under the bypass opening.
• By-pass is Closed - Open the by-pass by pulling the block above the door all the way out.
• Close the doors - if the flame is not getting enough air, first make sure the air control is open (all the way right). If additional air is needed, a small crack in the door is all that is needed.
• Cold Air Blockage - burn a piece of newspaper to establish a draft.
• Not enough starter paper - use additional newspaper if necessary.
• By-pass is Closed - Open the by-pass by pulling the ring above the door all the way out.
• Not enough air - first make sure the air control is open
(all the way right). If additional air is needed, a small crack in the door is all that is needed.
• By-Pass not Opened - Open the by-pass (the ring above the doors) using gloves or a tool before opening the door.
• Insufficient Draft - Chimney height and outside conditions can negatively affect draft. In these cases a small amount of smoke may enter the home. Adding more pipe or a draft-inducing cap may help.
• Wood is Wet - see the section "Selecting Wood" on page 12 for details on wood.
• Insufficient Draft - Chimney height and outside conditions can negatively affect draft. In these cases the fire may burn slowly. Adding more pipe or a draftinducing cap may help.
• Air Control is Not Wide Open - Make sure the air control is all the way to the right. Slide the control back and forth rapidly to insure the control is not stuck.
• Fireplace is Not Up to Temperature - This is normal.
The blower will come on when the fireplace is hot - usually 15 to 30 minutes.
• Electricity is Cut to the Blower - Check the household breaker or fuse to make sure it is operable.
• The door is not sealing - See the section "Check the
Door Seal, Adjust if Necessary" on page 16 for details.
© Travis Industries 4161018 100-01437
Maintenance
19
This wood heater contains a catalytic combustor, which needs periodic inspection and replacement for proper operation. It is against federal regulations to operate this wood heater in a manner inconsistent with operating instructions in this manual, or if the catalytic element is deactivated or removed.
Twice Yearly Maintenance
Check Firebrick, Baffle
Verify that the firebrick and baffle is in positon and not damaged (see illustration on page 23 for details).
Clean the Combustor
With the fireplace completely cool (at least two hours after the last coal has extinguished), use a vacuum cleaner, preferably with a brush, to draw all ash from the catalytic combustor (see the illustration below). Do not strike or scrape the combustor.
Testing your Catalyst Combustor
A combustor that is not functioning may still show active temperatures during the medium and high burn rates with the primary fire providing enough heat to hold output temperatures above 500°f. To check the combustor function burn your fireplace for at least 2-3 hours on the medium to high setting ensuring a full coal bed covers the firebox floor and the unit is at operating temperature. Set your burn rate to medium low and monitor the catalyst output temperature.
The combustor should maintain a temperature above 500°f. If your combustor temp falls below 500°f perform this test two or three times to ensure the results. If your results are the same your combustor may need cleaning or replacement. Note: If you reload your fireplace before starting your burn test, burn the new fuel load on high for at least 20 min before setting your burn rate to medium low.
Chimney Sweep Instructions
When sweeping (cleaning) the chimney, the combustor should be removed to prevent ash from clogging the combustor openings (when replacing the combustor use a new interim gasket). The damper plate (and other upper firebox components) can be removed during the chimney sweep or vacuumed after the chimney has been swept. See the illustration on page 23 for details.
© Travis Industries 4161018 100-01437
20
Maintenance
WARNING: Do not use substitute materials in the maintenance of this fireplace.
Door and Latch Inspection and Service
The door latch and door gasket work together to seal the firebox. If the door does not seal, air will leak into the firebox and cause the fire to burn too fast. This reduces the ability to burn the fireplace overnight or precisely adjust the burn rate.
Testing the Door Seal
The first indication that the door may not be sealing is when the door handle opens and closes without resistance. To test the door seal, open the door and place a dollar bill (US, Canadian, or
Australian) over the door opening. Then close the door over the bill. If the bill can be slid out of the door opening without resistance, the door gasket may need to be replaced.
Fixing the Door Seal
The first step to improve the door seal is to tighten the door latch. This is done by moving the door catch on the fireplace inwards. This adjustment should be done in very small increments and the door latch should be tested after each adjustment.
7/16" Wrench
To adjust the door catch, loosen these two nuts and slide the catch assembly back 1/16”.
If the door latch is very tight, yet the door seal is still loose, it may be time to replace the door gasket.
To replace the gasket, first strip the old gasket and any gasket cement off of the door. Attach the replacement gasket to the door and cut off any excess material (see page 22 for details).
Glass Inspection & Removal (use only 5mm neo-ceramic glass)
If the glass is cracked or broken, it must be replaced. The glass & gasket should seal against the door. See the illustration on page 22 for glass removal. When re-installing the glass, gently press the rope gasket in place (use a putty knife if necessary).
WARNING: The top of the glass comes close to the face of the fireplace. The glass must be all the way down to prevent is from striking the fireplace when the door is closed.
© Travis Industries 4161018 100-01437
Maintenance
21
Clean the Glass (if necessary)
This appliance has an air wash to keep the glass clean. However, burning un-seasoned wood or burning on lower burn rates leads to dirtier glass (especially on the sides). Clean the glass by following the directions below.
Do not clean when hot.
Allow the stove to fully cool. Apply glass cleaner or soapy water to the inside of the glass. Wipe with newspaper or a paper towel.
For Stubborn Creosote:
Dip newspaper or a paper towel in cool ashes and wipe it on the glass. The ash acts as a light abrasive.
The glass may develop a slight haze over time. This is normal and will not affect viewing of the fire.
Creosote – Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited this creosote makes an extremely hot fire.
The chimney shall be inspected at least twice a year during the heating season to determine when creosote buildup has occurred.
When creosote has accumulated it shall be removed to reduce the risk of a chimney fire.
© Travis Industries 4161018 100-01437
22
Maintenance
Replacement Parts List
Door Parts
4
5
6
7
ItemNo SKU
1 250-04188
2
3
250-04190
250-04220
99900402
250-04189
98500731
250-04221
Electrical Parts
ItemNo SKU
250-04176
250-04207
Description
DOOR ASS'Y, 42 APEX
HANDLE, DOOR 42 APEX
DOOR LATCH - 42 APEX
GSKT, DOOR 7/8" x 100" BLK #
GLASS, RECT. 42 APEX
GASKET KIT, GLASS FPX
HINGE PIN (2-PK) 42 APEX
1
1
1
1
Qty Includes
1 Entire Door Assembly
1
1
Handle, U Plate, Screws
All Nuts, Screws Included
7/8” Diameter Fiberglass
Gasket Tape, ½” Dia. Rope
2 Pins
Description
BLOWER, CONVECTION – 42 APEX
WIRE HRNS, MAIN – 42 APEX
Qty Includes
1
1
SNAP-DISC - 120deg NO#
1
© Travis Industries 4161018 100-01437
Maintenance
23
Firebox Parts
14
3
2
8
15
1
7
6
4
5
10
9
9
10
11
9
9
10
11
9
9
9
9
9
11
10
9
ItemNo SKU
1 250-04174
2
3
250-04219
250-02493
5
6
8
91001612
250-00556
250-04177
10
11
12
13
14
15
251-00083
251-00076
251-00082
251-00021
250-04202
250-03587
© Travis Industries
9
9
9
9
11
9
11
9
11
9
13
12
Description
KNOB w/ SCREW, AIR CNTRL
DAMPER EXT ROD
DAMPER YOKE ASS'Y#
GSKT KIT, CATALYTIC, 36/44E#
Qty Includes
1 Set Screw, Knob
1
1
Shaft & Threaded End
1
1 Interam Gskt, Kaowool Wedge
CATALYTIC COMBUSTOR, 36E/44E#
DAMPER SLDR PLATE
BRICK-CUT, 9" x 4-1/2" (#61)
BRICK-CUT, 9 x 2-7/16
BRICK-CUT, 6-1/2 x 2-1/2(#62)
BRICK-CUT, 9 x 2 #
4
6
1
1
CATALYTIC REAR BAFFLE -- 42 APEX 14" 1
1 Combustor, Interam Gskt
1
1
21
NOTE: Brick has slot
TEMP PROBE, THCPLE# -- CAT COMB 1
4161018 100-01437
24
Warranty
To register your TRAVIS INDUSTRIES, INC. 7 Year Warranty, complete the enclosed warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVIS INDUSTRIES, INC.,
10850 117th Place N.E., Kirkland, Washington 98033. TRAVIS INDUSTRIES, INC. warrants this appliance (appliance is defined as the equipment manufactured by Travis Industries, Inc.) to be defect-free in material and workmanship to the original purchaser from the date of purchase as follows:
Years 1 & 2 - COVERAGE: PARTS & LABOR
Air Control Assembly
Slider Plate, Linkage
Blower Assembly
Blower, Wire Harness, Snap Disk
Ceramic Glass
Glass (breakage from thermal shock)
Catalytic Combustor
Catalytic Combustor (see “Conditions and Exclusions” # 10)
Damper Assembly
Damper Plate, Linkage
Exclusions: Paint, Gasketing
Door Assembly
Door, Latch Assembly, Glass Retainers
Face Assembly
Faceplate, Fasteners
Firebox Assembly
Firebox, Combustor Support, Baffle, Air Channels
Firebrick
Breakage from thermal shock
Gold Plating
Face & Door (see “Conditions and Exclusions” # 9)
Accessories
Andiron, Summer Fan Switch
Re-Installation Allowance
In cases where heater must be removed from home for repairs, a partial cost of re-installation is covered
(pre-authorization required)
One-Way Freight Allowance
One-way freight allowance on pre-authorized repair done at factory is covered.
Years 3 Through 5 - COVERAGE: PARTS & LABOR
Coverage for thermal crumbling and disintegration only.
Air Control Assembly
Slider Plate, Linkage
Catalytic Combustor
Damper Assembly
Damper Plate, Linkage
Door Assembly
Door, Latch Assembly, Glass Retainers
Face Assembly
Faceplate, Fasteners
Firebox Assembly
Firebox, Combustor Support, Baffle, Air Channels
One-Way Freight Allowance
One-way freight allowance on pre-authorized repair done at factory is covered.
Exclusions: Paint, Gasketing, Blower Assembly, Glass, Firebrick, Gold Plating, Accessories, Re-Installation Allowance
Years 6 & 7 - COVERAGE: PARTS ONLY
Air Control Assembly
Slider Plate, Linkage
Damper Assembly
Damper Plate, Linkage
Door Assembly
Door, Latch Assembly, Glass Retainers
Face Assembly
Faceplate, Fasteners
Firebox Assembly
Firebox, Combustor Support, Baffle, Air Channels
Exclusions: Paint, Gasketing, Blower Assembly, Glass, Firebrick, Gold Plating, Accessories, Catalytic Combustor, Re-
Installation Allowance, One-Way Freight Allowance, Labor
CONDITIONS & EXCLUSIONS
1. This new appliance must be installed by a qualified installer. It must be installed, operated, and maintained at all times in accordance with the instructions in the Owner’s Manual. Any alteration, willful abuse, accident, neglect, or misuse of the product shall nullify this warranty.
2. This warranty is nontransferable, and is made to the ORIGINAL purchaser, provided that the purchase was made through an authorized Travis dealer.
3. Discoloration and some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not a defect and, therefore, not covered under warranty. Over-firing
(operation where the steel may glow red) of this appliance can cause serious damage and will nullify this warranty.
4. The warranty, as outlined within this document, does not apply to the chimney components or other Non-Travis accessories used in conjunction with the installation of this product. If in doubt as to the extent of this warranty, contact your authorized Travis retailer before installation.
5. Travis Industries will not be responsible for inadequate performance caused by environmental conditions such as nearby trees, buildings, roof tops, wind, hills or mountains or negative pressure or other influences from mechanical systems such as furnaces, fans, clothes dryers, etc.
6. This Warranty is void if: a. The unit has been operated in atmospheres contaminated by chlorine, fluorine or other damaging chemicals. b. The unit is subject to submersion in water or prolonged periods of dampness or condensation. c. Any damage to the unit, combustion chamber, heat exchanger or other components due to water, or weather damage which is the result of, but not limited to, improper chimney/venting installation.
7. Exclusions to this 7 Year Warranty include: injury, loss of use, damage, failure to function due to accident, negligence, misuse, improper installation, alteration or adjustment of the manufacturer's settings of components, lack of proper and regular maintenance, damage incurred while the appliance is in transit, alteration, or act of God.
8. This 7 Year warranty excludes damage caused by normal wear and tear, such as paint discoloration or chipping, worn or torn gasketing, chipped or cracked firebrick, etc. Also excluded is damage to the unit caused by abuse, improper installation, modification of the unit, or the use of fuel other than that for which the unit is configured (use cord wood only).
9. Damage to gold surfaces caused by fingerprints, scratches, melted items, or other external sources left on the gold from the use of cleaners other than denatured alcohol is not covered in this warranty. Damage to the gold surfaces from over-firing (operation where the steel may glow red) is not covered in this warranty.
10. Damage to the catalytic combustor due to mishandling, removal, cleaning, or other handling is not covered. Degradation of the combustor due to burning of anything other than natural cord wood is not covered. Burning of trash, garbage, artificial or paper logs, gift wrappings, coal, lighter fluids, chemical starters, treated or painted wood, driftwood or chemical cleaners will void the combustor warranty. These items contain chemicals that may cause the combustor to become deactivated.
11. TRAVIS INDUSTRIES, INC. is free of liability for any damages caused by the appliance, as well as inconvenience expenses and materials. Incidental or consequential damages are not covered by this warranty. In some states, the exclusion of incidental or consequential damage may not apply.
12. This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the Travis appliance without the express written permission of TRAVIS
INDUSTRIES, INC. and bearing a TRAVIS INDUSTRIES, INC. label of approval.
13. Any statement or representation of Travis products and their performance contained in Travis advertising, packaging literature, or printed material is not part of this 7 year warranty.
14. This warranty is automatically voided if the appliance’s serial number has been removed or altered in any way. If the appliance is used for commercial purposes, it is excluded from this warranty.
15. No dealer, distributor, or similar person has the authority to represent or warrant Travis products beyond the terms contained within this warranty. TRAVIS INDUSTRIES, INC. assumes no liability for such warranties or representations.
16. Travis Industries will not cover the cost of the removal or re-installation of hearths, facing, mantels, venting or other components.
17. If for any reason any section of this warranty is declared invalid, the balance of the warranty remains in effect and all other clauses shall remain in effect.
18. This 7 year warranty is the only warranty supplied by Travis Industries, Inc., the manufacturer of the appliance. All other warranties, whether express or implied, are hereby expressly disclaimed and purchaser’s recourse is expressly limited to the warranties set forth herein.
IF WARRANTY SERVICE IS NEEDED:
1. If you discover a problem that you believe is covered by this warranty, you MUST REPORT it to your Travis dealer WITHIN 30 DAYS, giving them proof of purchase, the purchase date, and the model name and serial number.
2. Travis Industries has the option of either repairing or replacing the defective component.
3. If your dealer is unable to repair your appliance’s defect, he may process a warranty claim through TRAVIS INDUSTRIES, INC., including the name of the dealership where you purchased the appliance, a copy of your receipt showing the date of the appliance’s purchase, and the serial number on your appliance. At that time, you may be asked to ship your appliance, freight charges prepaid, to TRAVIS INDUSTRIES, INC. TRAVIS INDUSTRIES, INC., at its option, will repair or replace, free of charge, your appliance if it is found to be defective in material or workmanship within the time frame stated within this 7 year warranty. TRAVIS INDUSTRIES, INC. will return your appliance, freight charges (years 1 to 5) prepaid by TRAVIS INDUSTRIES, INC., to your regional distributor, or dealership.
4. Check with your dealer in advance for any costs to you when arranging a warranty call. Dealers may require you to pay a service or trip charges for any warranty work. This charge can vary from store to store.
© Travis Industries 4161018 100-01437
Optional
25
GreenStart™Woodstove Igniter (Part # 94400951)
The optional GreenStart™ igniter is available for your fireplace. This accessory starts your fire with a simple push of a button.
push of the button. Contact your dealer for details.
© Travis Industries 4161018 100-01437
26
Index
Acid Wash ....................................................... 6
Adjusting the Burn Rate .................................. 10
Air Control (see 'Burn Rate') ........................... 10
Amps ............................................................... 5
Ash (Disposal) ................................................. 14
Baffle ............................................................... 15
Before Your First Fire ...................................... 6
Blower (Cleaning) ............................................ 15
Blower Operation ............................................ 10
BTU Output ..................................................... 5
Burn Rate ........................................................ 10
Burn Time ........................................................ 5
By-Pass Control .............................................. 8
Catalytic Combustor (Cleaning) ...................... 15
Catalytic Combustor (Operation) .................... 9
Catalytic Combustor (Replacement Info) ........ 17
Check Ash, Remove if Necessary .................. 14
Check Chimney for Creosote Build-Up ........... 16
Check Door Seal, Adjust if Necessary ............ 16
Check Firebrick, Baffle .................................... 15
Chimney (inspection) ...................................... 16
Clean any Gold Surfaces if Necessary ........... 14
Clean Combustor ............................................ 15
Clean the Blower Filter .................................... 15
Combustor (Cleaning) ..................................... 15
Combustor (Operation) ................................... 9
Combustor (Replacement Information) ........... 17
Curing the Paint .............................................. 6
Daily Maintenance (while fireplace is in use) .. 14
Don't Burn Treated Wood, Wax Logs, Etc. ..... 12
Door Gasket .................................................... 16
Door Latch ....................................................... 16
Dry Wood is Key ............................................. 12
Electrical Specifications .................................. 5
EPA Compliance ............................................. 5
Features .......................................................... 5
Firebrick .......................................................... 15
Fumes (after break-in period) ......................... 13
Fumes (first fire) .............................................. 6
Gold Surfaces (cleaning) ................................ 14
Heating Specifications .................................... 5
Hints for Burning ............................................. 11
Important Information ................................ 1
Index ......................................................... 22
Introduction ............................................... 1
Kindling ..................................................... 8
Listing Label .............................................. 18
Location of Controls .................................. 8
Log Length ................................................ 5
Maintaining Catalytic Burn-Off .................. 9
Normal Operating Sounds ........................ 11
Opening the Doors .................................... 7
Opening the Doors while Fireplace is Hot 7
Optional Equipment .................................. 20
Optional Summer Fan Switch ................... 10
Over-Firing the Fireplace .......................... 6
Overnight Burn .......................................... 11
Packing List ............................................... 5
Parts List ................................................... 17
Problems ................................................... 13
Re-Loading the Fireplace ......................... 11
Replacement Parts List ............................. 17
Safety Label .............................................. 18
Safety Notice ............................................. 6
Safety Precautions .................................... 2 & 3
Selecting Wood ......................................... 12
Starting a Fire ........................................... 8
Summer Fan Switch (Installation) ............. 21
Summer Fan Switch (Operation) .............. 10
Table of Contents ..................................... 4
Temperature Meter (Installation) .............. 20
Temperature Meter (Operation) ................ 9
Testing Wood Moisture ............................. 12
Troubleshooting ........................................ 13
Twice Yearly Maintenance ........................ 15
Verify the Installation ................................ 6
Warnings ................................................... 2 & 3
Warranty ................................................... 19
Watts ......................................................... 5
Why Dry Wood is Key ............................... 12
Wiring ........................................................ 21
Wood ......................................................... 12
Wood Cutting and Storage ....................... 12
© Travis Industries 4161018 100-01437

Public link updated
The public link to your chat has been updated.
Advertisement