Yamaha | BRX-750 | Owner's Manual | Micro Component System

AB
Micro Component System
OWNER’S MANUAL
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry,
clean place - away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold. For proper
ventilation, allow the following minimum clearances.
Top: 10 cm
Rear: 10 cm
Sides: 10 cm
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to this
unit, and/or personal injury.
Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
i En
17 Before moving this unit, press to set this unit to the
standby mode, and disconnect the AC power plug from
the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this unit
alone for cooling.
20 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
22 Excessive sound pressure from earphones and
headphones can cause hearing loss.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off
by . This state is called the standby mode. In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a qualified
service person should remove the cover or attempt to service this
device.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye
exposure to beam. When this unit is plugged into the wall outlet, do
not place your eyes close to the opening of the disc tray and other
openings to look into inside.
WARNING
DO NOT TOUCH THIS UNIT WHEN IT IS USED
CONTINUOUSLY AT HIGH VOLUME BECAUSE THE
BOTTOM OF THIS UNIT MAY BECOME HOT. IT MAY LEAD
TO INJURIES SUCH AS BURNS, ETC.
CONTENTS
WHAT YOU CAN DO WITH THIS UNIT ......... 2
SUPPLIED PARTS ................................................ 2
ABOUT DISCS AND FILES ................................. 3
Types of discs/files that can be used with this unit ... 3
Loading a disc............................................................ 4
Disc precautions......................................................... 4
Notice for watching 3D video images ....................... 4
Installing the batteries in the remote control ............. 9
Using the remote control ........................................... 9
SETUP MENU.......................................................34
Operation for SETUP menu .................................... 36
General Setting ........................................................ 37
Display Setting ........................................................ 39
Audio Setting ........................................................... 41
About the video output formats ............................... 42
SOFTWARE UPGRADE .....................................43
Upgrading the software............................................ 43
ADDITIONAL INFORMATION
TROUBLESHOOTING .......................................44
PREPARATIONS
CONNECTION..................................................... 10
NETWORK AND USB CONNECTION............ 13
Connecting to the NETWORK terminal.................. 13
Connecting to the USB port..................................... 13
GLOSSARY...........................................................52
SPECIFICATIONS...............................................54
OPERATIONS
Connecting component system to this unit.............. 10
Other connection...................................................... 11
Connecting to a TV.................................................. 12
HDMI connection .................................................... 12
Video connection ..................................................... 12
General..................................................................... 44
DAB reception ......................................................... 45
FM reception............................................................ 46
iPod .......................................................................... 46
USB ......................................................................... 47
Disc playback .......................................................... 48
Remote control ........................................................ 49
Network ................................................................... 49
Messages on the screen............................................ 50
Others....................................................................... 51
PREPARATIONS
FRONT PANEL AND BASIC OPERATION ..... 5
REMOTE CONTROL ........................................... 6
SETTINGS
INTRODUCTION
INTRODUCTION
OPERATIONS
INITIAL WIZARD/EASY SETUP..................... 14
Setting with the Initial Wizard/Easy Setup.............. 14
Basic operation using HOME/MEDIA menu.......... 15
Playing back photo/music/video.............................. 16
Using network content............................................. 18
Playing videos from YouTube™............................. 18
Basic operation without HOME/MEDIA menu ...... 19
Operation for iPod ................................................... 20
Operation for CDs.................................................... 20
ADVANCED PLAYBACK OPERATION......... 21
LISTENING TO DAB STATIONS .................... 25
Preparing the DAB tuning ....................................... 25
Tuning to DAB stations ........................................... 25
Presetting DAB stations........................................... 26
Selecting preset DAB stations (Preset tuning)......... 26
DAB station information ......................................... 26
DAB frequency information .................................... 27
Using DAB option menu ......................................... 27
LISTENING TO FM RADIO STATIONS ........ 28
Tuning to radio stations ........................................... 28
Presetting radio stations........................................... 28
Selecting preset radio stations (Preset tuning)......... 28
Displaying Radio Data System information
(U.K. model only) ............................................... 29
• This manual describes how to operate this unit using a
remote control except when it is not available. Some of
these operations are also available using the front panel
buttons.
• Notes contain important information about safety and
operating instructions. y indicates a tip for your
operation.
• “iPod” described in this manual may also refer to
“iPhone” or “iPad”.
• This manual is printed prior to production. Design and
specifications are subject to change in part as a result of
improvements, etc. In case of differences between the
manual and the product, the product has priority.
ADDITIONAL
INFORMATION
On Screen menu....................................................... 21
Status menu.............................................................. 22
Using Bookmark...................................................... 23
Program play............................................................ 23
Using search............................................................. 23
Enjoying BONUSVIEW™ and BD-Live™............ 24
■ About this manual
SETTINGS
BASIC OPERATION........................................... 15
The icons used in this manual
Icons are used to indicate available buttons/functions for a
particular format.
BD : BD-Video
DVD : DVD-Video, DVD-VR, DVD+VR
CD : Audio CD
VIDEO : AVCHD, WMV
MUSIC : MP3, WMA, WAV
PHOTO : JPEG
English
USING USEFUL FUNCTIONS .......................... 30
Using option menu on the front panel display......... 30
Setting the clock/timer and sleep timer ................... 31
Operating this unit by TV remote control
(the HDMI control function) ............................... 32
1 En
INTRODUCTION
WHAT YOU CAN DO WITH THIS UNIT
\
p. 21
\
p. 24
Play back Video, Music, Photo files on a disc/USB memory device/ \
iPod/iPhone/iPad*1
p. 15
Play back a commercially-released Blu-ray Disc™/DVD/CD*1
In addition to a Blu-ray Disc™ (BD disc), this unit also supports playback of a variety of other
discs.
Play back BONUSVIEW™, BD-Live™, etc.*1
You can enjoy additional movies on the latest BD discs.
Files recorded on discs/USB memory devices/iPod/iPhone/iPad can be played back with this
unit.
Play back Video, Music, Photo files on a Home Network Server*1,2
\
p. 18
\
p. 18
\
p. 25
\
p. 28
\
p. 14
\
p. 32
\
p. 16
PC contents can be played back with TV by connecting this unit to a network server.
Play back YouTube™ contents on the Internet*2
You can instantly enjoy YouTube™ contents on the Internet with this unit.
Receive DAB/DAB+ stations
You can enjoy listening to DAB/DAB+ stations. Also you can display station information on the
front panel display.
Receive FM Radio stations and Radio Data System information
(U.K. model only)
You can enjoy listening to FM radio stations with this unit. Also when the Radio Data System
broadcasting station is received, you can display Radio Data system information on the front
panel display of the unit (U.K. model only).
Perform the Initial Wizard/Easy Setup
You can easily set for language, resolution, screen aspect ratio with the Initial Wizard/Easy
Setup screen.
Operate with the TV remote control
Connecting devices with an HDMI cable, you can control devices with a single remote control
using the HDMI control function.
Play back high-quality virtual surround sounds by AIR
SURROUND XTREME
You can enjoy Yamaha’s exclusive AIR SURROUND XTREME that reproduces high-quality
virtual surround sounds.
*1 For details on playable discs and files, refer to page 3.
*2 Network setting is needed to use this function.
SUPPLIED PARTS
Make sure you have all of the following items.
Remote control
2 En
Batteries (×2)
(AAA, R03, UM-4)
Indoor DAB/FM
antenna
Composite video
cable (1.5m)
ABOUT DISCS AND FILES
Destination
Europe
• 12 cm and 8 cm discs can be played back in this unit.
Do not use an 8 cm to 12 cm adapter.
• Use discs that conform to compatible standards as
indicated by the presence of official logos on the disc
label. Playback of discs not complying with these
standards is not guaranteed. In addition, the image
quality or sound quality is not guaranteed even if the
discs can be played back.
Recording
Format
Disc Type
--
DVD-ROM
DVD-Video
--
DVD-Video/
DVD+VR/AVCHD/
Data Disc
WMV/MP3/WAV/
WMA/JPEG
CDDA/HDCD
--
CD-R/CD-RW
CDDA/Data Disc
WMV/MP3/WAV/
WMA/JPEG
USB
--
WMV/MP3/WAV/
WMA/JPEG
Network
--
WMV/MP3/WMA/
WAV/JPEG
BD-Video
Region code “A” or
“ALL”
DVD-Video
Region number “3”
or “ALL”
3
Central and South
America
Region code “A” or
“ALL”
Region code “A” or
“ALL”
ALL
Region number “4”
or “ALL”
4
Korea
Region code “B” or
“ALL”
ALL
Region number “4”
or “ALL”
4
ALL
Region code “C” or
“ALL”
Region number “5”
or “ALL”
5
China
Region code “C” or
“ALL”
ALL
Region number “6”
or “ALL”
ALL
Region management information
Asia
Australia
WMV/MP3/WAV/
WMA/JPEG
CD-ROM
Destination
2
Russia
BD-Video
DVD+R/DVD+R
DL/DVD+RW
DVD-Video
Region number “2”
or “ALL”
Data Format
BD-ROM/BD-R/
BD-RE
DVD-R/DVD-R DL/ DVD-Video/DVDDVD-RW
VR/AVCHD/Data
Disc
BD-Video
Region code “B” or
“ALL”
INTRODUCTION
Region management information
Types of discs/files that can be
used with this unit
ALL
Region number “3”
or “ALL”
3
ALL
• BD/DVD video players and discs have region codes,
which dictate the regions in which a disc can be played.
• BD/DVD Video operations and functions may be
different from the explanations in this manual and some
operations may be prohibited due to disc
manufacturer’s settings.
• If a menu screen or operating instructions are displayed
during playback of a disc, follow the operating
procedure displayed.
Notes
• Playback for some of the discs in the left side column tables
may not be possible depending on the disc.
• Finalize all recording media that is played back in this unit.
• “Finalize” refers to a recorder processing a recorded disc so that
it will play in other players/recorders as well as this unit. Only
finalized discs will play back in this unit. (This unit does not
have a function to finalize discs.)
• Playback of all files on the disc, USB memory device and
network is not guaranteed.
• A copyright protected file cannot be played back via a USB
memory device and network.
WMV file requirement
• WMV9, maximum resolution is 1,920 × 1,080.
3 En
English
MP3/WMA audio file requirement
• Sampling frequency: within 32 - 48 kHz (MP3/WMA),
LPCM 44.1 kHz/16 bit/Stereo (WAV)
• Bitrate: within 8 - 320 kbps (MP3), 32 - 192 kbps
(WMA)
ABOUT DISCS AND FILES
Loading a disc
• Insert the disc with the label facing up.
• In case of the disc recorded on both sides, face down the
side you want to play back.
Notes
• Playback may begin automatically, depending on the disc and
setting of this unit.
• The menu may be displayed first, depending on the disc.
• The disc load time may vary depending on the disc.
Disc precautions
• Do not touch the surface of the
disc. Hold a disc by its edge
(and the center hole).
• Do not use a pencil or pointed
marker to write on the disc.
• Do not put a tape, seal, glue, etc., on a disc.
• Do not use a protective cover to prevent scratches.
• Do not load more than one disc into this unit at one
time. This can cause damage to both this unit and the
discs.
• Do not insert any foreign objects into the disc slot.
• Do not load a cracked, warped, or glued disc.
• Do not expose a disc to
Caution
direct sunlight, high
temperature, high
humidity, or a lot of dust.
• If a disc becomes dirty,
wipe it with a clean, dry
cloth from the center out
to the edge. Do not use
record cleaner or paint
thinner.
• To avoid malfunction, do
not use a commercially
available lens cleaner.
4 En
Notice for watching 3D video
images
• Some people may experience discomfort (such as eye
strain, fatigue, or nausea) while watching 3D video
images. We recommend that all viewers take regular
breaks while watching 3D video images.
• If you experience any discomfort, stop watching the 3D
video images until the discomfort subsides. Consult a
doctor if you experience severe discomfort.
• Read the owner’s manuals (BD disc and TV) and/or the
caution messages that appear on the TV carefully.
• The vision of young children (especially those under six
years old) is still under development. Consult your
doctor (such as a pediatrician or eye doctor) before
allowing young children to watch 3D video images.
• Adults should supervise young children to ensure they
follow the recommendations described above.
FRONT PANEL AND BASIC OPERATION
This unit has an automatic standby function.
• When the source is set to Disc/USB/Network, this unit automatically switches to standby mode if it is left turned on for 1 hour without
playback or any other operation being performed.
• When the source is NOT set to Disc/USB/Network, this unit automatically switches to standby mode if it is left turned on for between
1 to 8 hours without playback or any other operation being performed according to the setting in SETUP menu (p. 37).
:
Front panel display:
(on/standby):
Opens/Closes the
disc tray.
(p. 30)
Turns this unit on/
Sets to standby mode.
INTRODUCTION
y
TIMER
TIMER indicator:
(p. 31, 32)
Disc tray
:
INPUT
Starts/Pauses
playback.
VOLUME
PHONES
USB
VOLUME
iPod iPhone iPod
PRESET
Down
Up
INPUT:
USB port:
Selects an input source.
(p. 11, 13)
:
Stops playback.
/
:
Skips backward and forward/Press
and hold to rewind and fast-forward.
PRESET < >:
Selects a preset station.
PHONES:
Connecting headphones
No sound is output from the speakers
when headphones are connected.
English
5 En
REMOTE CONTROL
1 Infrared signal transmitter (p. 9)
Note
will appear on the top left corner of the screen when the
pressed button is not available.
1
2
G
H
3
4
PROGRAM
MARKER
DIGEST
ZOOM
SLEEP
TIMER
5
6
7
8
9
0
SURROUND
CLEAR
SEARCH
DISPLAY
MUTE
SETUP
VOLUME
OPTION
I
J
K
L
M
N
HOME
TOP MENU
POP-UP MENU
O
2 MARKER DVD VIDEO : Sets Bookmark at a specified
point of a movie (p. 23). After Bookmark is set, press
DIGEST to select the set point you want to jump to. You can
set up to 12 Bookmarks.
3
: Opens/Closes the disc tray.
4 PROGRAM DVD CD : Sets the order of playback
(p. 23). You can set up to 15 tracks of an audio disc or titles/
chapters of a DVD-Video disc.
5 Numeric buttons: Enters numbers, or during playback,
jumps to the track/chapter corresponding to the number you
input. These buttons may not be available depending on the
disc type and playback condition.
6 CLEAR: Clears entered number/set item.
7 DISPLAY: Switches the information shown on the front
panel display (p. 20, 29).
8 SETUP: Displays SETUP menu screen (p. 34).
9 OPTION: Enters option menu mode (p. 30).
0 HOME: Displays HOME menu screen (p. 16).
A STATUS: Displays the playback information on the screen
(p. 22).
ENTER
RETURN
A
B
C
D
E
F
B DIMMER: Changes brightness of the front panel display.
Choose brightness between bright or dim by pressing this
button repeatedly.
ON SCREEN
TUNING
P
C SUBTITLE BD DVD VIDEO : Changes subtitle
languages (p. 53) if available. You can also select this item
from On Screen menu (p. 21).
Q
D PIP BD : Turns on/off the Picture in Picture (p. 24). PIP
Mark (
) is displayed on the screen when this function is
available. You can also select this item from On Screen menu
(p. 21).
PRESET
DIMMER
STATUS
PIP
SUBTITLE
AUDIO
SHUFFLE
REPEAT
A B
iPod
TV
AUX
DISC
USB NET
MEMORY
R
Note
TUNER
PIP Mark is displayed only when [PIP Mark] is set to [On]
(p. 38).
S
E REPEAT BD DVD CD VIDEO MUSIC
PHOTO : Selects repeat mode. Repeat mode shown below
will change each time you press the button (p. 20, 22).
: Repeats the title being played back.
: Repeats the chapter being played back.
: Repeats the folder being played back.
: Repeats all tracks/files on the disc/folder.
: Repeats the track/file being played back.
F SHUFFLE DVD CD VIDEO MUSIC
Selects shuffle play mode (p. 20, 21).
PHOTO :
G DIGEST PHOTO : Shows 12 photo thumbnails. When
thumbnails are displayed, you can proceed to the next/
previous page with
/
.
DVD VIDEO : Displays Bookmark select bar (p. 23).
H
6 En
: Turns this unit on or sets it to standby mode.
REMOTE CONTROL
I ZOOM DVD VIDEO PHOTO : Zooms in/out. The
size of the screen will change each time you press the button
(zoom in/out: 3 steps each).
INTRODUCTION
J Color buttons BD : Use these buttons according to onscreen instructions.
K SLEEP: Sets to sleep mode (p. 32).
L TIMER: Sets to timer mode (p. 31).
M SURROUND: Turns on/off surround playback mode for the
speakers (p. 16). (Does not affect headphone sound.)
N Volume control buttons: Controls the volume level
(p. 16).
Press MUTE to turn off the volume. Press again to resume
the volume.
O SEARCH BD DVD CD VIDEO MUSIC : Jumps
to a specified point during playback. For details on this
function, refer to “Using search” (p. 23). You can also select
this item from Status menu (p. 22).
P AUDIO BD DVD : Changes the audio language or
format. You can also select from On Screen menu (p. 21).
Q DAB/FM control buttons
TUNING << / >>: Starts manual tuning. Press and hold to
start automatic tuning (p. 28).
PRESET < / >: Selects preset station (p. 28).
MEMORY: Starts preset tuning and stores preset stations
(p. 28).
R A/B BD DVD CD VIDEO MUSIC : Plays back a
specific part you want to repeat.
1 Press A/B at the scene where you want to set the start
point. [A-] is displayed on the screen.
2 Press A/B again at the scene where you want to set the end
point. [A-B] is displayed on the screen.
Repeat playback starts.
3 To cancel the repeat playback, press A/B. [A-B]
disappears and the repeat playback is finished.
Note
This function cannot be performed depending on the
specifications of the disc.
S Input select buttons: Selects the input source (p. 15, 19,
28).
Continued to the next page. \
English
7 En
REMOTE CONTROL
T TOP MENU BD DVD : Displays the top menu screen
(p. 53) if the disc contains a menu. Select the desired item
using 5/a /2/3 and ENTER.
PROGRAM
MARKER
DIGEST
Note
ZOOM
Specific operations may be different depending on the disc.
Follow the instructions of each menu screen.
SLEEP
U Cursor buttons (5/a /2/3): Moves to select the focused
item.
ENTER: Confirms the focused menu/item.
TIMER
SURROUND
CLEAR
SEARCH
DISPLAY
V RETURN: Returns to the previous menu or screen, etc.
MUTE
SETUP
VOLUME
OPTION
t
HOME
TOP MENU
POP-UP MENU
X ON SCREEN: Displays On Screen menu (p. 21).
U
V
W
W POP-UP/MENU BD DVD : Displays pop-up menu. The
menu contents displayed vary depending on the disc. For
details on how to see and operate the pop-up menu, refer to
the manual for the disc. The top menu screen may be
displayed by pressing POP-UP/MENU depending on the
disc.
ENTER
RETURN
ON SCREEN
TUNING
PRESET
DIMMER
STATUS
PIP
SUBTITLE
AUDIO
SHUFFLE
REPEAT
A B
iPod
TV
AUX
DISC
USB NET
MEMORY
TUNER
X
Y
Y Control buttons
BD DVD CD VIDEO MUSIC PHOTO :
: Plays back contents.
: Stops playback. To stop playback completely, press this
button twice.
: Pauses playback.
BD DVD CD VIDEO MUSIC :
/
: Skips backward/forward.
/
: Press for instant search/replay. Instant search
skips the content 30 seconds. Instant replay replays the
content from 10 seconds before.
BD DVD CD VIDEO MUSIC :
/
: Searches backward/forward. The search speed
will change each time you press the button (search backward/
forward: 5 steps each). Press
to resume normal playback.
PHOTO :
/
: Changes the speed of a slide show (slower/
faster: 3 steps).
Note
Depending on the disc, this unit resumes playback from the
point where the unit was previously stopped. To play back
from the beginning, press
and then press
.
8 En
REMOTE CONTROL
Installing the batteries in the
remote control
3
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the front panel of this unit during
operation.
TIMER
INPUT
2
VOLUME
PHONES
INTRODUCTION
1
Using the remote control
USB
iPod iPhone iPod
PRESET
Within 6 m
(20 feet)
30˚
■ Notes on batteries
• Change both batteries when the operation range of the remote
control decreases.
• Use AAA, R03, UM-4 batteries.
• Make sure that the polarities are correct. Refer to the illustration
inside the battery compartment.
• Remove the batteries if the remote control is not to be used for
an extended period of time.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• Keep batteries away from children. If a battery is accidentally
swallowed, contact your doctor immediately.
• When not planning to use the remote control for long periods of
time, remove the batteries from the remote control.
• Do not charge or disassemble the supplied batteries.
30˚
Notes
• The area between the remote control and this unit must be clear
of large obstacles.
• Do not spill water or other liquids on this remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– high humidity, such as near a bath
– high temperature, such as near a heater or a stove
– extremely low temperatures
– dusty places.
• Do not expose the remote control sensor to strong lighting, in
particular, an inverter type fluorescent lamp; otherwise, the
remote control may not work properly. If necessary, position
the system away from direct lighting.
English
9 En
PREPARATIONS
CONNECTION
Connecting component system to this unit
Make sure you read the following procedure and note carefully before connecting the system.
■ Connecting the system
1 Connect the speaker terminals (L) of this unit to the speaker terminals of the left speaker and the speaker terminals
(R) of this unit to the speaker terminals of the right speaker using the speaker cables supplied with the speaker set
(NS-BP150).
2 Connect the supplied DAB/FM antenna to the DAB/FM jack.
Right speaker
(NS-BP150)
Left speaker
(NS-BP150)
MD player etc.
RCA stereo
cable
Be sure to remove insulation from
the end of each speaker cable.
SPEAKERS
L
R
Subwoofer
ANTENNA
6Ω MIN. /SPEAKER
L
AUX
OUTPUT
NETWORK
VIDEO
DAB/FM
75Ω
HDMI
R
AUDIO IN
SUBWOOFER
USB
This unit (BRX-750)
Video connection (p. 12)
HDMI connection (p. 12)
USB connection (p. 13)
10 En
Network connection (p. 13)
CONNECTION
■ Connecting the power cable
CAUTION
• Do not connect this unit or other components to the main power
until all connections between components are complete.
• Do not let the bare speaker wires touch each other or any metal
part of this unit. This could damage the unit and/or the speakers.
• All connections must be correct: L (left) to L, R (right) to R,
“+” to “+” and “–” to “–”. If the connections are faulty, no
sound will be heard from the speakers, and if the polarity of the
speaker connections is incorrect, the sound will be unnatural
and lack bass. Also, refer to the owner’s manual for each of
your components.
After you made all connections, connect the power cables
of this unit.
SPEAKERS
L
R
MAINS
ANTENNA
6Ω MIN. /SPEAKER
L
AUX
OUTPUT
NETWORK
VIDEO
DAB/FM
75Ω
HDMI
R
To an AC
wall outlet
AUDIO IN
SUBWOOFER
USB
PREPARATIONS
Notes
• When connecting speakers other than NS-BP150, use speakers
having more than 6Ω impedance.
• If there is a problem of weak radio wave reception in your area
or you want to improve radio reception, we recommend that
you use commercially available outdoor antennas. For details,
consult the nearest authorized Yamaha dealer or service center.
Other connection
■ Connecting iPod
You can enjoy music stored in your iPod by connecting it
to this unit.
Note
This unit is compatible with iPod classic, iPod nano (2nd, 3rd,
4th, 5th and 6th generation), iPod touch (1st, 2nd, 3rd, and 4th
generation), iPhone, iPhone 3G/3GS, iPhone 4, and iPad.
USB
iPod iPhone iPod
USB port
Notes
• Make sure the USB cable is connected securely between
your iPod and this unit.
• Connect your iPod to the front USB port of this unit. The
rear USB port is not compatible with your iPod.
English
11 En
CONNECTION
Connecting to a TV
Make sure you refer the following illustration carefully so that connections between this unit and your TV are properly
made.
CAUTION
Do not connect the power cable of this unit until all connections are completed.
This unit
Video cable
(supplied)
SPEAKERS
TV
L
R
VIDEO
AV INPUT
ANTENNA
6Ω MIN. /SPEAKER
L
AUX
OUTPUT
NETWORK
VIDEO
DAB/FM
75Ω
HDMI
R
HDMI IN
AUDIO IN
SUBWOOFER
USB
1
2
3
(ARC)
HDMI cable
(commercially available)
HDMI connection
• You can enjoy high quality digital picture and sound
through the HDMI terminals.
• Firmly connect an HDMI cable (commercially
available) to the HDMI terminal of this unit.
• Use HIGH SPEED HDMI cables that have the HDMI
logo (p. 55).
y
• When you use the HDMI control function, refer to “Operating
this unit by TV remote control (the HDMI control function)”
(p. 32) and “[HDMI Control]” (p. 37).
• For information on the output mode of the HDMI terminal,
refer to “[HDMI]” (p. 41).
• When no picture is displayed, refer to
“TROUBLESHOOTING” (p. 44).
■ Connection for the playback of Blu-ray
3D discs
You need the following equipment and connections to
enjoy BD 3D discs on this unit:
– a TV that has 3D functionality.
– a TV and this unit must be connected with HDMI
cables.
– a BD disc should contain 3D images.
12 En
■ About audio return channel (ARC)
supported TV
• You can connect an HDMI cable to the audio return
channel supported terminal (the terminal with “ARC”
indicated) on the TV.
• You need to activate the HDMI control function of this
unit so as to activate audio return channel (ARC) (p. 37).
What is audio return channel (ARC)?
This function allows digital audio signal to be output from
a TV to this unit through an HDMI cable, without using a
digital audio pin cable.
y
If your TV is not ARC supported, connect the TV and this unit
via the AUX jacks on the unit.
Video connection
• Firmly connect the composite video cable (supplied) to
the VIDEO jack.
• Refer to page 42 for information on the video output
formats.
Notes
• If you play back the image via VCR, the image may deteriorate
due to the copy guard function.
• To enjoy BD 3D discs on this unit, you need to connect a TV
and this unit using HDMI cables (commercially available).
NETWORK AND USB CONNECTION
Connecting to the NETWORK terminal
• PC contents can be played back by connecting this unit to the network.
• You can enjoy a variety of contents with interactive functions by connecting to the internet when playing BD-Live
compatible discs. Refer to page 24 for information on BD-Live functions.
Notes
Firmly connect a network cable (commercially available) to the NETWORK terminal.
Use only an STP (shielded twisted pair) network cable.
When using the internet, a broadband internet connection as shown below is required.
Connect the other connector of the network cable to the hub/broadband router.
When using a broadband internet connection, a contract with an internet service provider is required. For more details, contact your
nearest internet service provider.
• Refer to the operation manual of the equipment you have as the connected equipment and connection method may differ depending on
your internet environment.
• Use a network cable/router supporting 10BASE-T/100BASE-TX.
PREPARATIONS
•
•
•
•
•
This unit
Connecting to the USB port
SPEAKERS
• You can connect a USB memory device (2 GB or
greater and formatted with FAT 32/16) for BD Local
Storage to the USB port on the rear panel (or front
panel) of this unit to save the BD-Live data (p. 24) or to
upgrade the software of this unit (p. 43).
• Firmly connect a USB memory device (commercially
available) to the USB port.
L
R
ANTENNA
6Ω MIN. /SPEAKER
L
AUX
OUTPUT
NETWORK
VIDEO
DAB/FM
75Ω
HDMI
R
AUDIO IN
SUBWOOFER
USB
CAUTION
• Do not remove the USB memory device or unplug the power
cable while the operations for BD-Live or software upgrade are
being performed.
• Do not use a USB extension cable when connecting a USB
memory device to the USB port of this unit. Using a USB
extension cable may prevent the unit from performing correctly.
To USB
port
USB memory
device
(commercially
available)
Notes
• Yamaha cannot guarantee that all brands’ USB memory devices
will operate with this unit.
• For more notes on using USB memory devices, refer to
page 15.
To NETWORK
terminal
Network cable
(commercially
available)
y
To save BD-Live data on the USB
memory device on the front
panel, set [Local Storage] to
[Front USB] (p. 37).
To LAN
terminal
LAN
Internet
Modem
PC
English
Hub or
broadband router
■ After connecting
• When you set the Network setting manually, refer to “Network” (p. 38).
• To play back the PC contents on your network, refer to “Using network content” (p. 18).
13 En
OPERATIONS
INITIAL WIZARD/EASY SETUP
Setting with the Initial Wizard/Easy
Setup
Initial Wizard/Easy Setup allows you to set language,
resolution, and screen aspect ratio easily. Initial Wizard
screen is displayed when you turn this unit on for the first
time after purchase or upgrade. Same setting can be
performed from SETUP menu = [System] = [Easy
Setup] (p. 34).
1
When Easy Setup screen is displayed, press ENTER
to start Easy Setup.
2
Press 5/a to select the language you want to display
on the screen, then press ENTER.
3
Press 5/a to select the resolution, then press
ENTER. For details on setting items, refer to “[Video
Out Select]” (p. 39).
Note
When you connect your TV and this unit via the VIDEO
jack, select [Composite].
14 En
4
Press 5/a to select the screen aspect ratio, then
press ENTER. For details on setting items, refer to
“[TV Screen]” (p. 39).
Easy Setup is completed.
5
Press ENTER to exit Easy Setup.
Notes
• When no picture is displayed after Initial Wizard/Easy Setup is
completed, refer to “TROUBLESHOOTING” (p. 44).
• A warning message concerning 3D video playback appears
when this unit is turned on. Press ENTER to dismiss the
message or CLEAR to disable it (p. 37).
BASIC OPERATION
y
When the source is a CD/iPod/FM/TV, refer to “Basic operation without HOME/MEDIA menu” (p. 19). When the source is a BD/
DVD/USB/Network, read the following (a CD can also be played back with HOME/MEDIA menu).
Basic operation using HOME/MEDIA menu
Follow the procedures below to play back the source.
2 Switch the
1 Set the source
input
3 Refer to the following pages for more
operations
Disc
Front
Rear
DISPLAY
SETUP
OPTION
HOME
VOLUME
TOP MENU
USB*1
OPERATIONS
p. 16
POP-UP MENU
NETWORK
USB
ENTER
iPod iPhone iPod
USB
RETURN
ON SCREEN
p. 13, 16
TUNING
PRESET
DIMMER
STATUS
Network
(PC contents
and
YouTube)
p. 13, 18
*1
· Some devices may not work properly even if they meet the requirements.
· Playability of and power supply to all kind of USB devices are not guaranteed.
· The reading time may exceed 30 seconds depending on the number of files/folders.
· Yamaha and suppliers accept no liability for the loss of data saved on the USB devices connected to this unit.
As a precaution, it is recommended that the files are made backup copies.
English
15 En
BASIC OPERATION
■ Controlling the volume level
1
■ Common operations for playing back
files in a selected folder
Press the Volume control buttons (+/–) on the
remote control to increase/decrease the volume level
(p. 7).
Example: Selecting a movie file on a USB memory
device
■ Turning on/off surround playback mode
Note
1
Stop the playback of the video before you move to MEDIA menu
screen.
Press SURROUND to turn on/off surround playback
mode (p. 7).
When it is set to on:
– plays back surround sounds using Yamaha’s
exclusive AIR SURROUND XTREME (p. 52) if
the sources is a surround playback source such as
a BD.
– reproduces wider stereo sounds if the source is a
stereo playback source such as an audio CD.
1
Press HOME to move to HOME menu screen.
Playing back photo/music/video
HOME and MEDIA menus allow you to browse and play
multi-media files on data discs, USB memory devices and
your network.
y
HOME menu screen may differ depending on the model.
Note
For details on playable discs and files, refer to page 3.
2
Press 2/3/5 to select [MEDIA], then press
ENTER.
MEDIA screen appears.
3
Select the item which contains the file you want to
play back, then press ENTER.
■ Basic operation
DISPLAY
SETUP
OPTION
HOME
HOME
VOLUME
TOP MENU
POP-UP MENU
5
ENTER
2
ENTER
RETURN
ON SCREEN
a
5/a : Moves the focus.
2: Returns to the parent folder.
HOME: Moves to/exits HOME menu screen.
ENTER: Confirms the folder/file.
■ Icons on the top of MEDIA menu
: Plays back the disc on the tray, or displays
contents in the data disc.
: Displays contents in the USB memory device
connected to the USB port.
: Searches for a DLNA (p. 18) server on the
network.
: Displays contents on the connected DLNA server.
16 En
BASIC OPERATION
4
Select the Photo, Music, Video or AVCHD folder
you want to play back, then press ENTER.
To return to the parent folder, press 2 or select
.
6
Select the file you want to play back, then press
ENTER.
When a video file is selected, playback starts.
When a music file is selected, Status menu is
displayed and playback starts.
When a photo file is selected, slide show starts.
Note
Note that the only the file type selected on this step will be
displayed in the following step. For example, if you selected the
Photo folder in this step, only photo files are displayed after this
step. When you want to play back other than photo, return to this
step and select file type again.
To enjoy a slide show with music, press HOME to return to
HOME menu screen while music is played back, and select the
photo file.
5
Note
The displayed file may not be played back depending on the
content.
OPERATIONS
Select the folder(s) containing the file you want to
play back.
y
■ Operations for viewing photos
While viewing photos, the buttons on the remote control
work as shown below.
: Stops a slide show and returns to the file browser.
: Pauses a slide show.
: Plays a slide show.
: Moves to a next photo.
: Moves to a previous photo.
: Makes a slide show faster in 3 steps.
: Makes a slide show slower in 3 steps.
5 : Inverts a photo.
a : Reflects a photo.
2 : Rotates a photo counterclockwise.
3 : Rotates a photo clockwise.
ZOOM: Zooms in/out a photo (zoom in/out: 3 steps each).
5/a /2/3:Pans in zoom mode when a photo is
larger than the screen.
DIGEST: Switches to thumbnail mode (p. 6). When
thumbnails are displayed, you can proceed to the next/
previous page with
/
.
English
17 En
BASIC OPERATION
Using network content
■ About DLNA
3
Select the file you want to play back.
Notes
This unit is a DLNA certified digital media player. You
can manage photo, music and video contents stored on
DLNA servers on your home network.
DLNA (Digital Living Network Alliance) provides easy
sharing of digital media through network in the home, and
you can enjoy digital contents stored on your DLNAserver-software-installed PC or other DLNA compatible
device with your TV via this unit. To connect this unit to
your DLNA servers, some settings for the DLNA server or
device are required. For details, refer to your DLNA
server software or DLNA device.
• The playback and operating quality may be affected by your
home network condition.
• The files from removable media, such as USB memory devices
or DVD-drive on your media server, may not be shared
properly.
■ Playing back shared contents
1
Playing videos from YouTube™
You can watch movies from YouTube over the internet
using this unit.
The services may be changed without notice.
Press HOME to display HOME menu screen.
Note
To play back files on your PC, install a DLNA server software,
such as Windows Media Player 12, and share files you want to
play back.
1
Turn on the PC with DLNA server software installed
or the DLNA device connected to your home
network.
2
Press HOME to display HOME menu screen, then
select [MEDIA] to move to MEDIA menu.
The DLNA servers connected to the network are
listed on the screen.
y
HOME menu screen may differ depending on the model.
2
Press 5/a /2/3 to select [YouTube], then press
ENTER.
y
To return to HOME menu screen, press RETURN.
■ Notices for network services
Notes
• If your DLNA server is not listed, select [DLNA Search] to find
it.
• Depending on the DLNA server, this unit may need to be
permitted from the server.
• To play the file on the DLNA server, this unit and the server
must be connected to the same access point.
• The file requirements may not always be compatible. There
may be some restrictions depending on file features and DLNA
sever capability.
18 En
• Access to content provided by third parties requires a
high speed internet connection and may also require
account registration and a paid subscription.
• Third party content services may be changed,
suspended, interrupted, or discontinued at any time
without notice, and Yamaha disclaims any liability in
connection with such occurrences.
• Some content may only be available for specific
countries and may be presented in specific languages.
• Yamaha does not represent or warrant that content
services will continue to be provided or available for a
particular period of time, and any such warranty,
express or implied, is disclaimed.
BASIC OPERATION
Basic operation without HOME/MEDIA menu
Follow the procedures below to play back the source.
2 Switch the
1 Set the source
input
3 Select music and start playback
USB
iPod iPhone iPod
iPod*1
TUNING
PRESET
DIMMER
STATUS
PIP
SUBTITLE
AUDIO
SHUFFLE
REPEAT
A B
p. 11, 20
MEMORY
OPERATIONS
CD
p. 20
For details on operation, refer to the
instruction manual supplied with the device
connected such as a MD player, etc.
AUX
To AUX
DAB/FM
To receive DAB/FM radio stations, refer to page 25 or 28.
TV
To output TV sounds, refer to page 12 for connection and select the input source to TV (p. 7).
*1
· Some features may not be available depending on the model or the software version of your iPod.
· When you play back your iPod, Music Enhancer feature is enabled to enhance the sound for compressed music by regenerating
musical elements that are lost through compression. (Available only for iPod.)
■ Controlling the volume level
■ Turning on/off surround playback mode
1
1
Press the Volume control buttons (+/–) on the
remote control to increase/decrease the volume level
(p. 7).
Press SURROUND to turn on/off surround playback
mode (p. 7).
19 En
English
When it is set to on:
– plays back surround sounds using Yamaha’s
exclusive AIR SURROUND XTREME (p. 52) if
the sources is a surround playback source such as
a BD.
– reproduces wider stereo sounds if the source is a
stereo playback source such as an audio CD.
BASIC OPERATION
■ Repeat play
Operation for iPod
You can repeat playback as you want.
You can operate playback of your iPod by using the
buttons on the remote control.
DISPLAY
DISPLAY
SETUP
OPTION
HOME
1
Press REPEAT repeatedly for repeat play.
Each press cycles as follows:
VOLUME
TOP MENU
POP-UP MENU
Operation for CDs
ENTER
RETURN
ON SCREEN
You can also operate playback of music for CDs.
■ Playback controls
TUNING
,
REPEAT
SHUFFLE
,
PRESET
DIMMER
STATUS
PIP
SUBTITLE
AUDIO
SHUFFLE
REPEAT
A B
,
Note
Some features may not be compatible depending on the model or
the software version of your iPod.
■ Playback controls
1
Press any buttons below during playback.
: Stops playback.
: Pauses playback.
: Skips forward.
: Skips backward.
To start/resume playback, press
1
Press any buttons below during playback.
MEMORY
: Stops playback.
: Pauses playback.
: Skips forward.
: Skips backward.
: Searches forward.
: Searches backward.
: Press for instant search. Instant search skips the
music 30 seconds.
: Press for instant replay. Instant replay replays the
music from 10 seconds before.
To start/resume playback, press .
y
You can also use the Numeric buttons to enter the number of
the song directly. To clear the entry, press CLEAR.
.
y
Press DISPLAY to display information below on the front panel
display during playback.
• Song name
• Artist name
• Album name
■ Shuffle play
You can play back in random sequence.
1
Press SHUFFLE repeatedly for shuffle play.
Each press toggles as follows:
Note
There are some characters that cannot be displayed on the front
panel display of this unit.
■ Shuffle play
You can play back in random sequence.
1
Press SHUFFLE repeatedly for shuffle play.
Each press cycles as follows:
*1 You cannot set ALBUMS when you use an iPod touch,
iPhone, and iPad.
20 En
■ Repeat play
You can repeat playback as you want.
1
Press REPEAT repeatedly for repeat play.
Each press cycles as follows:
ADVANCED PLAYBACK OPERATION
This chapter explains playback of commercially available
BD/DVD/CD discs, and recorded DVD-RW/R discs.
DVD
–
–
–
–
–
–
–
Note
For the basic playback operation, refer to page 6.
On Screen menu
Normal
Shuffle CH (chapter)
Shuffle TT (title)
Shuffle All
Random CH (chapter)
Random TT (title)
Random All
VIDEO
MUSIC
PHOTO
– Normal
– Shuffle F (folder)
– Random F (folder)
To display On Screen menu, press ON SCREEN. After
that, press 5/a /2/3 to select an item, then press
ENTER to operate the desired function.
Audio BD DVD VIDEO : Shows audio language/
signal of a BD/DVD disc currently selected. You can
select the desired type of audio.
y
When the Angle Mark (
) is set to [On] (p. 38),
displayed on the screen when this function is available.
On Screen menu contains following items.
Title BD DVD VIDEO : Shows the title number being
played back. You can skip to the desired title by selecting
it from this item.
Chapter BD DVD VIDEO : Shows the chapter
number being played back. You can skip to the desired
chapter by selecting it from this item.
Track/File CD VIDEO MUSIC PHOTO : Shows
track/file number being played back. You can skip to the
desired track/file by selecting it from this item.
Time BD DVD CD VIDEO MUSIC : Shows the
playback time. Select display type from the following:
– Elapsed playback time of the title, chapter, disc,
track or file.
– Remaining playback time of the title, chapter, disc,
track or file.
Mode/Play Mode
DVD CD VIDEO MUSIC PHOTO : Shows current
playback mode. You can select playback mode from the
following:
CD
Subtitle BD DVD VIDEO : Shows the currentlyselected subtitle language when the subtitle is provided.
Subtitle Style BD : Shows the currently-selected
subtitle style. This function is available only for Video-file
external subtitle. You can select the desired text style of
subtitle.
Bitrate BD DVD CD VIDEO
bitrate of the audio/video signal.
MUSIC : Shows
Second Video BD : Turns the PIP on/off (p. 6).
Second Audio BD : Turns the secondary audio on/off.
Ins Search
BD
DVD
CD
VIDEO
MUSIC : Skips 30 seconds.
CD
VIDEO
MUSIC : Replays the content
Ins Replay
BD
DVD
from 10 seconds before.
Slide Show PHOTO :
Shows slide show speed. You can select the slide show
speed from Slow/Medium/Fast.
Transition PHOTO : Shows how photo appears on the
screen. You can select the transition type.
21 En
English
– Normal: Normal playback.
– Shuffle: Random playback without repetition.
– Random: Random playback with repetition.
is
OPERATIONS
Angle BD DVD : Shows the currently-selected angle
number. If the video is recorded with multiple angles, you
can change the angle.
ADVANCED PLAYBACK OPERATION
Status menu
CD
This shows various settings, such as subtitles, angle
settings and the title/chapter/track number currently
played back. To display Status menu, press STATUS.
Status menu contains following menus.
BD
DVD
MUSIC
Example: Icons when playing a music file
VIDEO
Example: Icons when playing a BD disc
1
2
3
4 5
6
8 7
1
2
3
1
(Playback status)
2
(Disc type/video file icon)
(Playback status)
(Repeat mode): Shows current repeat mode
(p. 6).
(Disc type/music file icon)
4 (Artwork) MUSIC : Displays artwork if the file
contains it.
3
(Title number being played): You can jump to
specified title with SEARCH button (p. 7).
5
4
(Chapter number being played): You can
jump to specified chapter with SEARCH button (p. 7).
6 (Information) MUSIC : Displays music information
if the file contains them.
5
(Subtitle currently selected): You can change
the subtitle language with SUBTITLE button (p. 6).
7
6
(Elapsed playback time): You can jump to
specified point with SEARCH button (p. 7).
8 (Progress bar) MUSIC : Shows progress status of
current song.
7
(Audio currently selected): You can change the
audio language or format with AUDIO button (p. 7).
8
(Track/file number being played): You can
jump to specified track with SEARCH button (p. 7).
(Elapsed playback time): You can jump to
specified point with SEARCH button (p. 7).
PHOTO
Example: Icons when viewing a photo file
(Repeat mode): Shows current repeat mode
(p. 6).
1
(Playback status)
2
(Photo file icon)
3
(File number being displayed)
4
(Repeat mode): Shows current repeat mode
(p. 6).
5 (Slide show speed)
22 En
ADVANCED PLAYBACK OPERATION
Using Bookmark
2
Press ENTER to program playback order.
For audio disc, press 5/a to select a desired track,
then press ENTER.
For DVD-Video discs, select a desired title (shown as
TT) and chapter (shown as CH) instead of a track.
To clear a set track, select the track you want to clear,
then press CLEAR.
Press RETURN to cancel the Program play.
3
After programming is finished, press
start program playback.
4
To cancel program play, stop playback completely by
pressing
twice.
This allows you to set Bookmark at the specified point of
the video. After Bookmark is set, you can move to the
point you set using this function. You can set up to 12
Bookmarks.
DVD
VIDEO
Example: Setting Bookmark when playing back a movie.
Press MARKER during playing back the movie to set
Bookmark. Bookmark number and the status are
displayed.
2
After Bookmark is set, press DIGEST to display
Bookmark select bar.
3
Press 2/3 to select the Bookmark you want to play
back, then press ENTER.
Press CLEAR to delete the selected Bookmark.
Note
When playback is finished (e.g., ejecting the disc, pressing
twice), Bookmarks are automatically deleted.
Program play
This allows you to program playback order of audio disc
tracks or DVD chapters.
You can program up to 15 tracks/chapters.
DVD
CD
Example: Programming the playback order of CD tracks
1
Press PROGRAM during playback to display
PROGRAM screen.
to set and
OPERATIONS
1
Using search
This allows you to jump to the specified point during
playback.
BD
DVD
CD
VIDEO
MUSIC
Example: Searching to the specified point
1
Press SEARCH during playback. Status bar appears.
2
Press 5/a /2/3 to select one of the item below,
then press ENTER.
BD
DVD :
– Title number (shown as
)
– Chapter number (shown as
)
– Elapsed title time (shown as
)
– Elapsed chapter time (shown as
)
CD :
– Track number (shown as
)
– Elapsed track time (shown as
)
– Elapsed disc time (shown as
VIDEO
)
MUSIC :
– File number (shown as
)
)
English
– Elapsed file time (shown as
Continued to the next page. \
23 En
ADVANCED PLAYBACK OPERATION
3
4
Press 5/a or number buttons to set/adjust the value
of the focused item, and press ENTER to jump to the
specified point.
To close the status bar, press STATUS.
■ Using the feature of BD-Live™
1
Set the Network setting (p. 38).
2
Connect the USB memory device to this unit (p. 13).
• BD-Live data is saved in a USB memory device
connected to this unit.
• Connect a USB memory device (2 GB or greater
and formatted with FAT 32/16) supporting USB
2.0 High Speed (480 Mbit/s) to the USB port that
you select on Local Storage (p. 37). The default
setting is the USB port on the rear panel.
• A “BUDA” folder is created automatically in the
USB memory device when necessary.
• If there is insufficient storage space, the data will
not be copied/downloaded. Delete unneeded data
or use a new USB memory device.
• Some time may be required for the data to load
(read/write).
Enjoying BONUSVIEW™ and BDLive™
This unit supports BONUSVIEW (p. 52) (BD-ROM
Profile 1 Version 1.1) and BD-Live (p. 52) (BD-ROM
Profile 2) playback functions.
Note
Functions and playback method vary depending on the disc.
Refer to the guidance on the disc or the supplied user’s manual.
■ Using Picture in Picture function
(secondary audio/video playback)
BD-Video that includes secondary audio and video
compatible with Picture in Picture can be played back
with secondary audio and video simultaneously as a small
video in the corner.
Primary video
1
Secondary video
While PIP Mark (
) or Secondary Audio Mark
(
) is displayed, press PIP to turn the Picture in
Picture function on/off.
Notes
• To listen to secondary audio from a TV connected with an
HDMI cable, make sure that the Audio Output setting (HDMI)
is set to [PCM] (p. 41).
• Depending on the disc, to listen to secondary audio, you may
need to set secondary audio to on from the top menu of the disc
(p. 8).
• The secondary audio and video for Picture in Picture may
automatically play back and be removed depending on the
content. Also, playable areas may be restricted.
24 En
3
Play back the disc.
4
Run BD-Live according to the instructions on the
disc.
Notes
• Regarding playback method of BD-Live contents, etc.,
perform the operations in accordance with the instructions
in the BD disc manual.
• To enjoy BD-Live functions, perform the network
connection (p. 13) and Network settings (p. 38).
• Refer to “[BD-Live Connection]” (p. 38) regarding the
setup to restrict access to BD-Live contents.
• The time required to download the provided programs into
the USB memory device connected to this unit varies
depending on the internet connection speeds and the data
volume of the programs.
• BD-Live programs provided through the internet may not
be able to display the connection depending on the status
(upgrading) of the provider. In such cases, take out the
disc and try again.
• If the BD-Live screen does not appear for a while after
you select the BD-Live function in the BD disc menu, the
USB memory device may not have enough free space. In
such cases, eject the disc from this unit, and then erase the
data in the USB memory device selecting [Format] in
[Local Storage] (p. 37).
LISTENING TO DAB STATIONS
DAB (Digital Audio Broadcasting) uses digital signals for
clearer sound and more stable reception compared to
analog signals.
This unit can also receive DAB+ (an upgraded version of
DAB) that allows stations using MPEG-4 HE-AAC v2
audio codec, which has a more efficient transmission
method and provides higher sound than DAB.
Tuning to DAB stations
TUNING
PRESET
Preparing the DAB tuning
Before tuning into DAB stations, an initial scan must be
performed. The initial scan starts automatically when you
select DAB as the input source for the first time.
SUBTITLE
AUDIO
REPEAT
A B
iPod
TV
AUX
DISC
USB NET
SUBTITLE
AUDIO
REPEAT
A B
iPod
TV
AUX
DISC
USB NET
MEMORY
TUNER
TUNER
2
Press << / >> (TUNING) to select a DAB station.
Some stations have sub (secondary) stations. The
secondary indicator lights up when a secondary audio
station is selected.
MEMORY
TUNER
TUNER
Secondary indicator
Press TUNER repeatedly to select DAB mode.
y
You can also perform the initial scan manually by selecting [INIT
SCAN] from option menu (p. 27, 30).
While the scan is in progress, [Scanning] and the
percentage of the progress appear on the front panel
display.
OPERATIONS
1
PIP
SHUFFLE
PIP
SHUFFLE
<<, >> (TUNING)
Press TUNER repeatedly to select DAB mode.
PRESET
STATUS
STATUS
1
TUNING
DIMMER
DIMMER
y
You can change the order of DAB stations by selecting [STATORDER] from option menu (p. 27, 30).
Note
If this unit cannot receive the DAB signal, [Off Air] is displayed
on the front panel display.
When scanning is complete, the number of receivable
DAB stations appears on the front panel display for a
while, then the unit airs the first station as stored in station
order.
Note
This unit can receive Band III (174 - 240 MHz) only.
English
25 En
LISTENING TO DAB STATIONS
1
Presetting DAB stations
You can store your favorite DAB stations with the preset
function.
OPTION
OPTION
HOME
TOP MENU
POP-UP MENU
5
ENTER
ENTER
RETURN
ON SCREEN
a
TUNING
PRESET
DIMMER
STATUS
PIP
SUBTITLE
<, > (PRESET)
AUDIO
MEMORY
<<, >> (TUNING)
MEMORY
Press DISPLAY repeatedly while listening.
The following describes the flow of DAB station information.
STATION
Displays the name of the current DAB station and preset
number.
↓
DLS (Dynamic Label Segment)
Displays information about the current DAB station, such as
the name of the song, artist and speaker, etc. This data is
continuously updated by the DAB broadcaster, thus changing
often with every new song or program.
Other data, such as news, weather, and sports headlines, may
be broadcast as well.
↓
ENSEMBLE
Displays the name of the current ensemble.
Select a favorite DAB station by pressing << / >>
(TUNING).
↓
2
Press MEMORY.
↓
3
Select the preset number you want to store by
pressing 5/a or < / > (PRESET).
1
4
• You can preset up to 30 DAB stations.
• To cancel the preset while choosing a preset number, press
MEMORY again.
• You can delete a preset station by pressing OPTION → S/T
→ ENTER to select [PRESET DEL] (p. 30).
Selecting preset DAB stations
(Preset tuning)
TUNING
PRESET
1
STATUS
SUBTITLE
<, > (PRESET)
AUDIO
MEMORY
Select the preset radio station in DAB mode by
pressing < / > (PRESET).
y
You can also use the Numeric buttons on the remote control or
< / > (PRESET) on the front panel of this unit to select the preset
radio station.
DAB station information
DISPLAY
CH/FREQ.
Displays the channel label and frequency of the current DAB
station.
↓
SIGNAL Q.
Displays signal reception quality (from 0 (none) to 100 (best))
of current DAB tuning.
↓
AUDIO FORMAT
Displays the audio format of the current station, and whether
DRC (Dynamic Range Control)*1 is activated or not. [(DRC
ON)] is displayed when [DRC MODE] is set to [AUTO]
(p. 30) and DRC information is transmitted by the DAB
station.
*1 Some DAB broadcasters transmit a wide dynamic range
enabling high quality sound, accompanied by DRC
information.
Use this feature to compress the dynamic range of the DAB
broadcast. This is especially useful when you listen to a
DAB station in a noisy environment or at low volume at
night.
y
You can change the DRC setting by selecting [DRC MODE]
from option menu (p. 30).
↓
Back to STATION
Note
DISPLAY
SETUP
VOLUME
OPTION
TOP MENU
26 En
↓
↓
y
PIP
TIME
Displays the current time.
BITRATE
Displays the bitrate of the current DAB station.
Press ENTER.
The preset is complete.
DIMMER
PROGRAM TYPE
Displays the genre of the current DAB station.
HOME
POP-UP MENU
Not all DAB broadcasters transmit station information.
LISTENING TO DAB STATIONS
DAB frequency information
This unit can receive Band III only.
Using DAB option menu
The DAB option menu appears on the front panel display.
For details on option menu, refer to page 30.
Frequency
Channel label
174.928 MHz
5A
176.640 MHz
5B
178.352 MHz
5C
180.064 MHz
5D
181.936 MHz
6A
183.648 MHz
6B
185.360 MHz
6C
187.072 MHz
6D
188.928 MHz
7A
190.640 MHz
7B
192.352 MHz
7C
194.064 MHz
7D
y
195.936 MHz
8A
197.648 MHz
8B
After performing [INIT SCAN], this unit airs the first station
as stored.
199.360 MHz
8C
201.072 MHz
8D
202.928 MHz
9A
204.640 MHz
9B
Note
206.352 MHz
9C
208.064 MHz
9D
Once [DAB CLEAR] is performed, the deleted information
and preset settings cannot be restored.
209.936 MHz
10A
211.648 MHz
10B
213.360 MHz
10C
215.072 MHz
10D
[TUNE AID]: Measures reception strength of the
received DAB signal (from 0 (none) to 100 (best)).
Adjust the DAB/FM antenna to find the best position to
receive the DAB signal.
216.928 MHz
11A
y
218.640 MHz
11B
220.352 MHz
11C
222.064 MHz
11D
223.936 MHz
12A
225.648 MHz
12B
227.360 MHz
12C
229.072 MHz
12D
230.784 MHz
13A
232.496 MHz
13B
234.208 MHz
13C
235.776 MHz
13D
237.488 MHz
13E
239.200 MHz
13F
■ Setting [STAT-ORDER] and
[DRC MODE]
[STAT-ORDER]: Enables you to change the station
order. Set to [ENSEMBLE] to list the stations in
ensemble order. The default setting is
[ALPHANUMERIC].
[DRC MODE]: Changes the DRC setting. This function
utilizes DRC automatically if it is transmitted. The
default setting is [AUTO].
■ Performing [INIT SCAN] and
[DAB CLEAR]
[INIT SCAN]: Performs the initial scan manually. Each
time you perform [INIT SCAN], the newly received
stations are added to the previously received stations.
OPERATIONS
[DAB CLEAR]: Deletes all DAB station information
and preset settings stored in this unit. After [DAB
CLEAR] is completed, the unit moves to the INIT
SCAN function automatically.
■ Using [TUNE AID]
To check the frequency corresponding to the channel label,
refer to “DAB frequency information” (p. 27).
English
27 En
LISTENING TO FM RADIO STATIONS
■ Manual preset tuning
Tuning to radio stations
1
Select a favorite radio station by pressing << / >>
(TUNING).
2
Press MEMORY.
3
Select the preset number you want to store to by
pressing 5/a or < / > (PRESET).
4
Press ENTER.
The manual preset is complete.
TUNING
<<, >> (TUNING)
PRESET
DIMMER
STATUS
PIP
SUBTITLE
AUDIO
SHUFFLE
REPEAT
A B
iPod
TV
AUX
DISC
USB NET
MEMORY
TUNER
TUNER
1
Press TUNER repeatedly to select FM mode.
2
Press and hold << / >> (TUNING).
Automatic tuning starts.
y
y
If the signal received from the station you want to select is weak,
you can also tune into radio stations manually by pressing << /
>> (TUNING) repeatedly. In this case, the sound will be
monaural.
Presetting radio stations
• You can preset up to 30 FM stations.
• To cancel the manual preset while choosing a preset number,
press MEMORY again.
• You can delete a preset station by pressing OPTION → S/T
→ ENTER to select [PRESET DEL] (p. 30).
Selecting preset radio stations
(Preset tuning)
You can store your favorite FM stations with the preset
function.
OPTION
OPTION
DIMMER
STATUS
PIP
SUBTITLE
<, > (PRESET)
HOME
TOP MENU
POP-UP MENU
RETURN
ON SCREEN
a
TUNING
PRESET
DIMMER
STATUS
PIP
SUBTITLE
<, > (PRESET)
AUDIO
MEMORY
AUDIO
MEMORY
5
ENTER
ENTER
<<, >> (TUNING)
MEMORY
■ Automatic preset tuning
1
Press and hold MEMORY for more than 3 seconds in
FM mode.
2
Press ENTER.
Start the automatic preset.
Note
When you perform the automatic preset, all stored stations are
cleared and the new stations are stored.
28 En
TUNING
PRESET
1
Select the preset radio station in FM mode by
pressing < / > (PRESET).
y
You can also use the Numeric buttons on the remote control or
< / > (PRESET) on the front panel of this unit to select the preset
radio station.
LISTENING TO FM RADIO STATIONS
Displaying Radio Data System
information (U.K. model only)
DISPLAY
DISPLAY
SETUP
OPTION
HOME
VOLUME
TOP MENU
1
POP-UP MENU
Press DISPLAY repeatedly while listening.
PS (Program Service)
↓
PTY (Program Type)
↓
RT (Radio Text)
↓
CT (Clock Time)
↓
OPERATIONS
MONO/STEREO
↓
Frequency
↓
Back to the PS
Note
If the signal transmission of the Radio Data System station is too
weak, this unit may not be able to receive Radio Data System
information completely. In particular, RT (Radio Text)
information uses a lot of bandwidth, so it may be less available
compared to other types of information.
English
29 En
USING USEFUL FUNCTIONS
Using option menu on the front panel display
The option menu appears on the front panel display by pressing OPTION. You can set various useful functions with
option menu.
Option menu
Parameter or control range
DEL*1
PRESET
Reference page
(Displays only when the input source is set to DAB/FM.)
26, 28
STAT-ORDER*1
ALPHANUMERIC/ENSEMBLE
(Displays only when the input source is set to DAB.)
27
DRC MODE*1
AUTO/OFF
(Displays only when the input source is set to DAB.)
27
DAB CLEAR*1
(Displays only when the input source is set to DAB.)
27
INIT SCAN
(Displays only when the input source is set to DAB.)
27
TUNE AID
(Displays only when the input source is set to DAB.)
27
TREBLE
–10 dB to +10 dB
below
BASS
–10 dB to +10 dB
below
BALANCE
L+5 - CENTER - R+5
below
BASS BOOST
ON/OFF
below
ON/OFF
below
AUTO
CLOCK*2
*1
When DAB stations are not registered, these option menus do not appear.
*2 This function is available only for Europe, U.K. and Australia models.
CLEAR
CLEAR
SEARCH
DISPLAY
SETUP
OPTION
HOME
■ Setting tone/balance
MUTE
VOLUME
OPTION
TOP MENU
POP-UP MENU
5
ENTER
2
3
ENTER
RETURN
*4 Also effective when you are using headphones.
ON SCREEN
a
1
Press OPTION.
2
Select desired option menu by pressing 5/a .
3
Press ENTER to confirm.
4
Change the settings by pressing 5(3)/a (2).
5
Press ENTER to complete the setting. *3
6
Press OPTION to exit option menu.
*3 To set additional items, repeat steps 2 to 5.
30 En
[TREBLE]*4: Adjusts the high frequency response.
[BASS]*4: Adjusts the low frequency response.
[BALANCE]: Adjusts the volume level of each left and
right speaker channel.
[BASS BOOST]: Boosts the low frequency response
when set to [ON].
■ Adjusting the clock
[AUTO CLOCK]: Applies automatic adjustment
function for the clock. To apply for this function, set
[AUTO CLOCK] to [ON].
USING USEFUL FUNCTIONS
Setting the clock/timer and sleep
timer
PROGRAM
MARKER
DIGEST
4
Change the settings by pressing 5/a or Numeric
buttons.
5
Press ENTER to confirm the setting.
6
Repeat steps 2 through 5 to set each setting item.
y
ZOOM
SLEEP
SLEEP
TIMER
TIMER
SURROUND
■ Setting the clock
• To clear the entry, press CLEAR.
• The settings of the timer are retained.
The following describes the flow of timer setting.
(Clock)
You can set the clock by using the remote control directly.
The clock appears on the front panel display.
Press TIMER.
2
Press ENTER.
3
Set hour and minute by pressing 5/a .
Press 2/3 to switch the hour or minute setting.
4
Press ENTER to complete the setting.
y
When setting the clock, you can also use the Numeric buttons
to enter the hour and minute. To confirm the entry, press
ENTER. To clear the entry, press CLEAR.
Note
The time setting will be lost if you disconnect the power cable
from the wall outlet.
■ Setting the timer
The timer sets this unit to play back the source at the time
you set.
1
Press TIMER.
2
Select desired setting items (OnTime/Period/Source/
Volume) by pressing 5/a .
3
Press ENTER to confirm the item.
OnTime (hour/s and minute/s)
Set the desired time to execute the timer.
Period (playback time)
By selecting [– – –], playback time is endless.
Set the Source or preset number
Note
OPERATIONS
1
If the source is not set properly, the timer sound
will not be heard. Make sure that the source is
set properly.
CD:
When you select the CD as a source, this unit
resumes the music that you were listening to
last time.
iPod:
When you select the iPod as a source, this unit
resumes the music that you were listening to
last time.
DAB/FM:
Set preset number.
By selecting [– – –], the DAB/FM station you
set last time is set.
English
Continued to the next page. \
31 En
USING USEFUL FUNCTIONS
Volume
The volume level can be set between [1] [MAX] and [– – –]*1. When the timer is
executed while this unit is in standby mode, the
volume level you set at this point is applied.
When the timer is executed while the unit is on,
the volume level remains the same as the
current volume level.
*1 If you set your volume level to [– – –] and the
timer is executed while this unit is in standby
mode, the volume level is applied at the same
level as input source.
Operating this unit by TV remote
control (the HDMI control function)
You can use the TV remote control to operate this unit if
your TV supports the HDMI control function and is
connected to this unit’s HDMI terminal.
Remote control of TV (Example)
Turns on/off both TV and
this unit.
Timer setting is complete.
Switch the timer to [OFF]/[ONCE]/[EVERY]
by pressing 2/3. When the timer is set to
[ONCE] or [EVERY], the TIMER indicator
lights up on the front panel.
Notes
• The clock has to be set in advance.
• When the timer is set, the TIMER indicator lights up on the
front panel. While the power is on, the TIMER indicator flashes
as the set time of the timer becomes closer.
■ Setting the sleep timer
Controls the volume of
this unit.
The sleep timer sets this unit to standby mode after the
specified time elapses.
1
Select this unit or TV to
output sounds.*1
Press SLEEP repeatedly.
You can also enjoy the following function.
• When you start playback of DVD/BD discs other than
CD discs on this unit or display HOME/SETUP menu
screen, the input selector of the TV is switched to this
unit automatically (One Touch Play).
*1 When you select this unit to output TV sounds by using the
TV remote control, the unit automatically selects TV as the
input source, and sound can be enjoyed from either the
speakers or headphones connected to the unit.
Notes
• The TV needs to be an ARC supported TV.
• This unit may be operated by using cursor buttons of TV remote
control for some TVs.
• Even if your TV supports the HDMI control function, some
functions may not be available. For details, refer to the manual
supplied with your TV.
• HDMI control function may not work properly depending on
the TV.
• Functions other than ones shown above may work depending on
the TV.
32 En
USING USEFUL FUNCTIONS
• In order to make the HDMI control function available, set up
settings for the HDMI control function on ALL components
(this unit, TV, and other components). Certain operation may
also be required.
• Each function may be set independently to activate/deactivate
depending on the TV.
• Refer to the operation manuals supplied with the TV for details
regarding setup.
■ Setting the HDMI control function
1
Turn on all components connected to the TV with
HDMI.
2
Check all components connected with HDMI and
enable the HDMI control function on each
component.
For this unit, set [HDMI Control] to [On] (p. 37).
For external components, refer to the manual
supplied with each component.
y
3
The HDMI control function is not working even
checking the above
• Turn off this unit and the TV, and then turn them back
on again.
• Unplug the AC power supply cable of this unit, the TV
and external components connected to the TV with
HDMI.
Plug them in again after about 30 seconds.
■ Changing the connection method and
connected components
When the connected components and jacks are changed,
reset this unit with following procedures.
1
Turn off the HDMI control function of the TV and
this unit, turn off all connected devices, and change
the connections.
2
Perform the step 1 to 3 of “Setting the HDMI control
function” (p. 33).
OPERATIONS
• The default setting of [HDMI Control] is set to [Off] for
this unit.
• The example of TV settings
– From a setup menu on your TV, select “Link setting” =
“HDMI control setting” (example), then set a setting
such as “HDMI control function” to “ON” (example).
– Setting such as “Speaker priority” should be set to “AV
amplifier”.
If the HDMI control function is not working
Check the following:
• The TV is connected to the HDMI terminal of this unit.
The HDMI control function is set to [On] in SETUP
menu (p. 37).
• The HDMI control function is enabled on the TV. (Also
check the relative settings such as power interlock
function or speaker priority.)
Turn off the TV and then turn on it again.
■ Registering HDMI components to TV
1
Select this unit as the input source of the TV.
2
Select Disc/USB/Network as the input source of this
unit.
3
Check that the image from this unit is correctly
displayed on the TV.
4
Check that the HDMI control function works (turn on
this unit or adjust the volume level using the TV
remote control).
y
For some HDMI components, you only need to set the HDMI
control function. Registering HDMI components to TV is not
required in this case.
English
33 En
SETTINGS
SETUP MENU
The SETUP menu enables various audio/visual settings and adjustments for functions using the remote control unit.
Menu/Submenu
Item
System
Screen Saver
Sets screen saver to On/Off.
37
Auto Power Off
Disc/USB/Net: Sets auto power off mode to On/Off.
Other Inputs: Sets auto power off mode to on by hours or Off.
37
Disc Auto Playback
Sets this unit to start disc playback automatically.
37
HDMI Control
Sets this unit to receive control signal from the remote
control of your TV.
37
Load Default
Resets all settings to the default setting except Security
setting.
37
General Setting
Language
Playback
Security
Network
34 En
Function
Page
Upgrade
Performs upgrade of this unit.
37
Easy Setup
Sets language, resolution, screen aspect ratio.
37
Local Storage
Displays status of Local Storage, formats Local Storage and
selects the front/rear USB port for Local Storage.
37
3D Playback
Message
Displays a warning message concerning 3D video playback
when this unit is turned on.
37
OSD
Selects the language for On Screen Display.
37
Menu
Prioritizes the language for disc menu.
37
Audio
Prioritizes the language for audio.
37
Subtitle
Prioritizes the language for subtitle.
37
Closed Caption
Sets the closed caption to On/Off.
38
Angle Mark
Sets to display the Angle Mark when a BD/DVD disc with
multiple angles is played back.
38
PIP Mark
Sets to display the PIP Mark when a BD/DVD disc with
Picture in Picture is played back.
38
Secondary Audio
Mark
Sets to display the Secondary Audio Mark when a BD/DVD
disc with secondary audio is played back.
38
Last Memory
Sets this unit to remember the last playback position of a disc
when it is set to standby mode or the disc tray is opened.
38
Change Password
Changes password for Parental Control and Country Code.
38
Parental Control
Sets the Parental Control depending on the disc content.
38
Country Code
Sets your Country Code.
38
Internet Connection
Sets the internet connection to Enable/Disable.
38
Information
Displays network information screen.
38
Connection Test
Performs the network connection test.
38
IP Setting
Sets the IP setting to Auto/Manual.
38
BD-Live
Connection
Sets the BD-Live connection to Permitted/Partial Permitted/
Prohibited.
38
DLNA
Sets the DLNA to Enable/Disable.
38
Proxy Setting
Sets the proxy setting.
38
SETUP MENU
Menu/Submenu
TV
Function
Page
Selects 3D or 2D videos.
39
TV Screen
Sets the screen aspect ratio of the connected TV, and adjust
the video output.
39
Video Out Select
Selects the resolution of video output.
39
TV System
Selects the TV System from NTSC/PAL/Multi.
39
Color Space
Selects Color Space from YCbCr 4:4:4/YCbCr 4:2:2/ Full
RGB/RGB.
39
HDMI Deep Color
Selects HDMI Deep Color from 30 bits/36 bits/Off.
39
HDMI 1080p 24Hz
Sets HDMI 1080p 24Hz to Auto/Off.
40
Lip Sync
Adjusts the lag between video and audio, such as when the
mouth movement is out of sync with the voice.
40
Video Mode
Adjusts the visual image.
40
Color Adjust
Adjusts Brightness/Saturation/Hue for each color.
40
Noise Reduction
Sets the level of Noise Reduction.
40
De-interlacing
Mode
Sets how to detect the video signal.
Audio Output
HDMI
Selects the output mode of HDMI terminal from Bitstream/
PCM/Off.
41
DRC
Sets the DRC (Dynamic Range Compression).
41
Post Process
UpMix
Multi-channelizes the 2-channel audio signal.
41
Display Setting
Video Process
Audio Setting
Item
3D Output
40
Displays software version and MAC address (p. 53).
41
System
Information
SETTINGS
English
35 En
SETUP MENU
Operation for SETUP menu
3
Select a menu item.
Press 5/a to select [Parental Control], then press
ENTER or cursor 3.
4
Enter your password with Numeric buttons.
– The default password is 0000.
– You cannot move to the next setting screen until
you have input the correct password.
– To change the password, refer to “[Change
Password]” (p. 38).
5
Select a next item.
Press 5/a to select the Parental Control Level for
BD/DVD discs, then press ENTER.
6
Exit the menu screen.
Press 2 to return to the previous menu.
You need to display SETUP menu screen to perform
settings for this unit. The following is the explanation for
basic operations of SETUP menu.
SLEEP
Numeric
buttons
TIMER
SURROUND
CLEAR
SEARCH
MUTE
SETUP
DISPLAY
SETUP
VOLUME
VOLUME
OPTION
OPTION
HOME
HOME
TOP MENU
POP-UP MENU
5
ENTER
2
3
ENTER
RETURN
ON SCREEN
a
Example: Setting [Parental Control]
Notes
• Some items cannot be set when the input source is set to other
than Disc/USB/Network. In this case, set the input source to
Disc/USB/Network.
• Some items cannot be set during playback. In this case, press
twice to stop playback completely before setting.
1
2
Press SETUP to display SETUP menu screen.
Press 2/3 to select [General Setting], then press
ENTER or a .
Select a Submenu.
Press 5/a to select [Security], then press ENTER or
cursor 3.
36 En
SETUP MENU
General Setting
The default settings are marked with “ * ”.
■ System
[Screen Saver]
You can set the screen saver to [On]/[Off].
When set to [On], this unit will switch to screen saver
mode if there is no operation for 3 minutes.
[Local Storage]
You can display Local Storage information, format Local
Storage, and select [Front USB]/[Rear USB] to save the
BD-Live data.
To format (empty) the “BUDA” folder in the USB
memory device, select [Information] and press ENTER
when [Format] is focused on the screen.
Front USB, Rear USB*
y
On*, Off
Local Storage is used as an auxiliary memory when a BD disc is
played back.
[Auto Power Off]
You can set auto power off mode to [On]/[Off] when the
input is selected to Disc/USB/Network. When other inputs
are selected, auto power off mode can be set by hours or to
[Off].
[3D Playback Message]
You can turn on or off a warning message concerning 3D
video playback that appears on the TV when this unit is
turned on.
Disc/USB/Net: On*, Off
Other Inputs: 1 hour, 2 hours, 4 hours, 8 hours*, Off
■ Language
[Disc Auto Playback]
You can set [Disc Auto Playback] to [On]/[Off]. When set
to [On], a disc will play back automatically after loading.
On*, Off
[HDMI Control]
You can set this unit to receive control signal from a TV
compatible with the HDMI control function via an HDMI
cable (p. 12).
On, Off*
y
Note
When set to [On], power consumption during standby mode
increases due to the HDMI control function.
[Load Default]
You can reset all settings of this unit to default setting
except Security setting (p. 38). For details on default
settings, refer to pages 34-41.
[Upgrade]
You can upgrade the software manually from [USB
Storage] or [Network]. For details on software upgrade,
refer to “SOFTWARE UPGRADE” (p. 43).
[Easy Setup]
You can perform Easy Setup (p. 14).
[OSD]
You can select the language for On Screen Display which
is the messages or menu displayed on the screen such as
SETUP menu.
English*, Français , Español , Deutsch , Italiano ,
Svenska , Nederlandse ,
,
[Menu]
You can prioritize the language for disc menu.
English*, Français ,
, Español , Deutsch , Italiano ,
Nederlandse , Portuguese, Danish, Svenska , Finnish,
Norwegian,
, Korean, Japanese, More
[Audio]
You can prioritize the audio language for BD/DVD
playback. For details on setting items, refer to “[Menu]”
(p. 37).
SETTINGS
For details on the HDMI control function, refer to page 32.
On*, Off
[Subtitle]
You can prioritize the language for Subtitle.
English, Français ,
, Español , Deutsch , Italiano ,
Nederlandse , Portuguese, Danish, Svenska , Finnish,
Norwegian,
, Korean, Japanese, More, Off*
English
37 En
SETUP MENU
■ Playback
[Closed Caption]
You can set to display the closed caption (p. 52) when a
BD/DVD disc with closed caption is played back.
On, Off*
[Angle Mark]
You can set to display the Angle Mark (
) when a BD/
DVD disc with multiple angles is played back.
On*,
Off
[PIP Mark]
You can set to display the PIP Mark (
) when a BD
disc with picture in picture (p. 24) is played back.
On*, Off
[Secondary Audio Mark]
You can set to display the Secondary Audio Mark (
)
when a BD disc with secondary audio is played back.
On*, Off
[Last Memory]
You can set whether this unit remembers the last playback
position of a disc when it is set to standby mode or the disc
tray is opened.
On*, Off
[Country Code]
You can set the Country Code you live in. The password
(refer to “[Change Password]” on page 38) needs to be
entered before the Country Code is set. This setting may
be used for rating of the Parental Control and disc
playback.
■ Network
[Internet Connection]
You can set to [Enable] when you use BD-Live (p. 24),
DLNA (p. 18) and software upgrade from the network
(p. 43).
Enable*, Disable
[Information]
You can display network information screen. On this
screen, you can view the information of Interface
(Ethernet), Address Type, IP Address, Subnet Mask,
Default Gateway, and DNS.
[Connection Test]
You can perform an internet connection test. If the test is
failed, please check [IP Setting] (p. 38) and perform the
test again.
[IP Setting]
You can configure the network settings.
Auto*
Select to automatically configure the network
settings of this unit with the DHCP server.
Manual
Select to configure the network settings (IP Address,
Subnet Mask, Default Gateway, and DNS) manually.
Note
Some discs are not compatible with this function.
■ Security
[Change Password]
You can set the password for changing the Parental
Control Level and Country Code. Refer to “[Parental
Control]” (p. 38) and “[Country Code]” (p. 38).
Notes
y
•
•
•
•
Numeric buttons
2/3
CLEAR
ENTER
Enters characters.
Moves the highlight.
Deletes a character.
Saves the settings and exits from the menu.
[BD-Live Connection]
You can set access restriction to BD-Live contents.
• The default password is 0000.
• If you forget the password, refer to “TROUBLESHOOTING”
(p. 44) and set all the Security settings to their default settings.
Permitted
Allows all BD-Live discs to connect the network.
Partial
Permitted*
Allows only discs with owner certification.
[Parental Control]
In some BD/DVD discs, a control level for disc viewing is
set depending on the age of the viewer. You can set the
Parental Control shown on the screen depending on the
disc content.
The password (refer to “[Change Password]” on page 38)
needs to be entered before the Parental Control Levels is
set.
After you set the Parental Control, when you play back a
disc with level higher than current Parental Control Level,
or you want to change the Parental Control Level, a dialog
box will pop up to ask you to enter the password.
Prohibited
Prohibits all BD-Live discs to connect the network.
[DLNA]
You can set the DLNA (p. 18) to [Enable]/[Disable].
When you do not use the DLNA function, set to [Disable].
Enable*, Disable
[Proxy Setting]
You can set Proxy Setting. Set to [Disable] for normal use.
Set to [Enable] to set the proxy setting.
Enable
Enables proxy host and proxy port setting.
Disable*
Sets proxy server to disable. Select this item when
proxy server is not used.
Proxy Host
Sets proxy host.
Proxy Port
Sets proxy port.
Off*, 1 to 8
38 En
SETUP MENU
Display Setting
The default settings are marked with “ * ”.
■ TV
[3D Output]
You can select 3D or 2D video output from this unit.
Auto*
This unit automatically selects 3D or 2D videos.
Off
This unit always selects 2D videos.
[Video Out Select]
You can select the video output resolution from
[Composite], [HDMI Auto], [HDMI 1080p], [HDMI
1080i], [HDMI 720p], [HDMI 480p/576p], and [HDMI
480i/576i]. When set to [HDMI Auto], resolution is set to
the maximum resolution according to the connected TV.
For more details on output formats, refer to “About the
video output formats” (p. 42).
Composite, HDMI Auto*, HDMI 1080p, HDMI 1080i, HDMI
720p, HDMI 480p/576p, HDMI 480i/576i
Notes
Note
Even if you set [3D Output] to [Auto] and play back a BD 3D
disc, this unit selects 2D images depending on the connection and
the setting of TV, etc (p. 12).
[TV Screen]
You can set the screen aspect ratio of the connected TV,
and adjust the video output.
If you switch your TV (i.e. because you have bought a
new one) and the screen aspect ratio of the connected TV
changes, you will have to change the TV Screen setting.
16:9 Full
Select this when this unit is connected to a TV with a
16:9 screen. When a 4:3 aspect ratio video is played
back, the video is displayed as shown below.
16:9 Normal* Select this when this unit is connected to a TV with a
16:9 screen. When a 4:3 aspect ratio video is played
back, the video is displayed as shown below.
4:3 Letterbox Select this when this unit is connected to a TV with a
4:3 screen. When a 16:9 aspect ratio video is played
back, the video is displayed as shown below.
Original
image size
[TV System]
You can select [TV System] from [PAL], [NTSC] and
[Multi]. Set the same TV System as your TV set. For more
details on output formats, refer to “About the video output
formats” (p. 42).
NTSC, PAL*, Multi (Australia, Asia, China, U.K., Europe and
Russia models)
NTSC*, PAL, Multi (Central and South America models)
[Color Space]
You can select the Color Space (p. 52) output from
HDMI. This function is available when this unit is
connected with an HDMI cable.
YCbCr 4:4:4* Sets Color Space to YCbCr 4:4:4.
YCbCr 4:2:2
Sets Color Space to YCbCr 4:2:2.
Full RGB
When RGB is set and white and black on the screen
are too faint, select this item. This setting is effective
when a connected component supports RGB 0-255
range.
RGB
Outputs video signal at normal signal range.
On 16:9 (wide screen) TV
16:9 Full
16:9 Normal
SETTINGS
4:3 Pan Scan Select this when this unit is connected to a TV with a
4:3 screen. When a 16:9 aspect ratio video is played
back, the video is displayed as shown below.
• When you connect your TV and this unit via the VIDEO jack,
select [Composite], [HDMI 480p/576p], or [HDMI 480i/576i].
• To output HD audio (such as Dolby TrueHD or DTS-HD) from
the HDMI terminal, set [Video Out Select] to [HDMI Auto] or
more than [HDMI 720p].
Note
4:3
Original
image size
This function is only available on TVs that support this function.
On 4:3 TV
4:3 Pan Scan
4:3 Letterbox
[HDMI Deep Color]
When your TV is compatible with Deep Color (p. 52), set
this item according to your TV. This function is available
when this unit is connected with an HDMI cable.
30 bits, 36 bits, Off*
16:9
English
39 En
SETUP MENU
[HDMI 1080p 24Hz]
This outputs the BD-Video encoded in 24Hz frame rate in
HDMI 1080p 24Hz. Smoother video playback may be
available with this function. This function is available
when your TV supports this function, and this unit is
connected with an HDMI cable. For more details on
output formats, refer to “About the video output formats”
(p. 42).
Auto*, Off
This setting is disabled when output resolution is other than
1080p.
[Lip Sync]
You can set/adjust the Lip Sync (p. 53) function.
Auto*
This unit adjusts the Lip Sync function
automatically.
Manual
You can adjust the Lip Sync function manually. You
can set the delay of the audio for 2D and 3D contents
independently.
2D
3D
This unit does not adjust the Lip Sync function.
■ Video Process
[Video Mode]
You can select [Video Mode] below.
Standard*
The image is most natural and well-balanced. This
mode suits for normal use.
Vivid
The image is more vivid and sharp.
Cinema
The image suits for watching movie in dark room.
Custom
You can adjust the visual image manually. Press 5/
a to select the parameter, then press 2/3 to adjust
the figure.
Brightness
Adjusts the overall brightness of the image.
Saturation
Adjusts the richness of the color in the projected
image.
Hue
Adjusts the tint of the projected image.
Contrast
Adjusts the bright areas (white levels) in the image.
Sharpness
Adjusts the sharpness of objects in the video.
CTI
Smooths out the edges of color images. Color images
are rendered more distinct.
The default settings are 0.
40 En
The default settings are 0.
[Noise Reduction]
You can set the Noise Reduction to a level of 0 to 3. 0 is
off, and 3 is the maximum level.
0*, 1, 2, 3
Note
Off
[Color Adjust]
You can adjust Brightness/Saturation/Hue for each color
(Red/Green/Blue/Yellow/Cyan/Magenta). To use this
function, set [Video Mode] to [Custom]. For details on the
setting items, refer to “[Video Mode]” (p. 40).
[De-interlacing Mode]
You can select how to detect the video signal. Set to
[Auto] for normal use. When horizontal stripping noise
appears on the screen, set this to [Film]/[Video] to remove
the noise.
Auto*, Film, Video
SETUP MENU
Audio Setting
The default settings are marked with “ * ”.
■ Audio Output
[HDMI]
You can select the output mode of the HDMI terminal.
Bitstream, PCM, Off*
Notes
• To output sound from the speakers or headphones, select [Off].
• No sound of your iPod can be output from this unit to the TV
through the HDMI cable.
• To output HD audio (such as Dolby TrueHD or DTS-HD) from
the HDMI terminal, set [Video Out Select] to [HDMI Auto] or
more than [HDMI 720p] (p. 39).
[DRC]
You can set the DRC (Dynamic Range Compression)
(p. 53) to [On]/[Off]/[Auto]. When set to [Auto], DRC is
automatically turned on for a source with DRC
information in Dolby TrueHD format. DRC makes the
strong sound such as plosive sound lower, and
conversations more audible. It is useful when you watch
movies in the night.
Off*, On, Auto
■ Post Process
SETTINGS
[UpMix]
You can multi-channelize the 2-channel audio signal
(effective on HDMI output). To multi-channelize, select
[DTS NEO:6], then select [Cinema] or [Music].
Off*, DTS NEO:6
■ System Information
Software version and MAC address (p. 53) are displayed.
English
41 En
SETUP MENU
About the video output formats
When [TV System] is set to [NTSC]
Resolution Composite
HDMI
VIDEO
Playback BD
others
Playback BD
others
HDMI
Auto
HDMI
HDMI
480i/576i 480p/576p
480p
Max
480i
480p
480i
OFF
480i
480i
HDMI
720p
720p 60 Hz
HDMI 1080p
HDMI
1080i
24Hz
1080i 60 Hz
1080p 24 Hz
1080p 60 Hz
Others
1080p 60 Hz
OFF
When [TV System] is set to [PAL]
Resolution Composite
HDMI
VIDEO
Playback BD
others
Playback BD
others
HDMI
Auto
HDMI
HDMI
480i/576i 480p/576p
576p
Max
576i
576p
576i
OFF
576i
576i
HDMI
720p
720p 50 Hz
HDMI 1080p
HDMI
1080i
24Hz
1080i 50 Hz
1080p 24 Hz
1080p 50 Hz
Others
1080p 50 Hz
OFF
When [TV System] is set to [Multi]
When [TV System] is set to [Multi], video signal is output at the same frequency as the source. Refer to the tables above
for details on the frequency setting of the TV and resolution of the output video signal.
While a menu screen such as SETUP menu is displayed, video signal is output at the same frequency as the source.
Notes
• “Max” in the table means that resolution is set to the maximum resolution supported by the connected TV.
• [HDMI 1080p 24Hz] setting is disabled when output resolution is other than [HDMI 1080p].
• No signals are output from the VIDEO jack when output resolution is set to [HDMI Auto], [HDMI 720p], [HDMI 1080i], or [HDMI
1080p].
• When [TV System] is set to [NTSC] and video source is not 60 Hz, the video output signal is converted to 60 Hz.
• When [TV System] is set to [PAL] and video source is not 50 Hz, the video output signal is converted to 50 Hz.
42 En
SOFTWARE UPGRADE
Some of the newly released BD discs cannot be played
back unless you upgrade this unit software to the latest
version. We recommend upgrading the software of this
unit with software upgrade so that the unit is operated
based on the latest software.
To check for the availability of a software upgrade, visit
http://download.yamaha.com/
Note
Do not remove the USB memory device, set this unit to standby
mode or unplug the power cable/LAN cable while the software
upgrade is being performed.
Upgrading the software
1
Prepare for the software upgrade.
When you upgrade the software from [Network]:
Confirm that this unit is connected to the network.
Select the upgrade method and start upgrade from
SETUP menu.
1 Press SETUP to display SETUP menu screen.
2 Select [General Setting] = [System] =
[Upgrade].
3 Select the item which contains the upgrade file
package from [USB Storage]/[Network].
3
Start upgrade by following the on-screen messages.
English
2
SETTINGS
When you upgrade the software from [USB Storage]:
1 Save the upgrade file package to the appropriate
folder on the USB memory device. For more
details, refer to the procedure document attached
with the upgrade file package.
2 Connect the USB memory device.
If the software upgrade is started automatically
when the USB memory is connected, skip step 2
below.
43 En
ADDITIONAL INFORMATION
TROUBLESHOOTING
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
General
Problem
Cause
No power.
This unit fails to turn
on or enters standby
mode soon after the
power is turned on.
Remedy
Press
on the front panel to turn on the power.
Page
5
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
11
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to standby mode, disconnect the power
cable, plug it back in after 30 seconds and then use it
normally.
—
This unit needs to be restarted.
Press and hold
on the front panel for around 5
seconds to restart this unit. To completely restart,
unplug the power cable from the AC outlet for 5 to
10 seconds, plug the power cable to the AC outlet
again, and then turn on this unit.
5
The disc cannot be
played back.
The Initial Wizard is not set.
Set the Initial Wizard when you turn this unit on for
the first time after purchase or upgrade.
14
No sound.
No appropriate input source has been
selected.
Select an appropriate input source with INPUT on
the front panel (or the Input select buttons on the
remote control).
5
Speaker connections are not secure.
Secure the connections.
10
The mute function is on.
Cancel the mute function.
7
The volume is turned down.
Turn up the volume.
7
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by
this unit.
3
[HDMI Control] is set to [Off].
When connecting ARC (Audio Return Channel)
supported TV and this unit using an HDMI cable
only, set [HDMI Control] to [On].
37
No sound from the
speakers or
headphones.
[HDMI] for audio output in SETUP menu
is not set to [Off].
Set [HDMI] to [Off].
41
No picture.
Incorrect cable connections.
Make sure that the cables are connected correctly.
12
Make sure that the connected TV is set to the correct
input.
12
Connect this unit to the TV with VIDEO jack using
the supplied video pin cable.
– If picture is still not displayed with this unit
connected to the VIDEO jack, press and hold
and
on the front panel simultaneously
for around 5 seconds when no disc is inserted and
playback is stopped to switch NTSC/PAL.
12
Press and hold
and
on the front panel
simultaneously for around 5 seconds when no disc is
inserted and playback is stopped to switch NTSC/
PAL. Set resolution properly again when connecting
through HDMI (p. 39).
—
This unit does not
operate properly.
TV system is set incorrectly.
44 En
TROUBLESHOOTING
Problem
The power is
suddenly turned off.
Cause
Remedy
Page
The sleep timer is set.
This is not malfunction. Turn on this unit and play
the source again.
32
[Auto Power Off] is set to [On].
Set [Auto Power Off] to [Off].
37
The clock setting has
been cleared.
The power cable has been disconnected.
Connect the power cable, and set the clock again.
—
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10
There is noise
interference from
digital or radio
frequency
equipment.
This unit is too close to the digital or
high-frequency equipment.
Move this unit farther away from such equipment.
—
These sounds are not malfunctions of this unit but
are normal operating conditions.
—
This unit makes a
snapping sound
when starting
playback or loading a
disc.
No sound from the
subwoofer.
The subwoofer is not connected properly.
Check that the subwoofer is connected properly.
10
The system settings
change
automatically.
When [HDMI Control] is set to [On],
operations of the TV (for example,
changing channels, etc.) changes the
system settings.
Set [HDMI Control] to [Off] or set the system again
by using its remote control.
37
The HDMI control
function does not
work properly.
[HDMI Control] is set to [Off].
Set [HDMI Control] to [On].
37
The HDMI control function is disabled
on your TV.
Refer to the manual supplied with your TV and
check the setting.
—
The automatic
lipsync is not
effective even [Lip
Sync] is set to [Auto].
The TV does not support the automatic
lipsync.
Set [Lip Sync] to [Manual] and then manually adjust
the audio output delay.
40
Remedy
Page
DAB reception
Cannot tune into any
DAB stations.
Cause
Perform the initial scan operations
30
There is no DAB coverage in your area.
Check with your dealer or WorldDMB online at
http://www.worlddab.org for a listing of the DAB
coverage in your area.
—
The DAB signals are too weak.
Use the TUNE AID feature to locate the best
positioning of the indoor DAB/FM antenna.
30
The initial scan
operations are not
successful and [Not
found] appears on the
front panel display.
The DAB signals are too weak.
Use the TUNE AID feature to locate the best
positioning of the indoor DAB/FM antenna.
30
There is no DAB coverage in your area.
Check with your dealer or WorldDMB online at
http://www.worlddab.org for a listing of the DAB
coverage in your area.
—
The DAB station
reception is weak.
The positioning of the indoor DAB/FM
antenna and/or this unit is not optimal
for DAB reception.
Use the TUNE AID feature to locate the best
positioning of the indoor DAB/FM antenna and this
unit for optimal DAB reception.
30
The DAB signals are too weak.
Use the TUNE AID feature to locate the best
positioning of the indoor DAB/FM antenna and this
unit for optimal DAB reception.
30
English
The initial scan operations were not
performed.
ADDITIONAL
INFORMATION
Problem
45 En
TROUBLESHOOTING
Problem
Cause
Remedy
Page
There is noise
interference (e.g. hiss,
crackle or jitter).
The indoor DAB/FM antenna needs to
be repositioned.
Readjust the position of the indoor DAB/FM
antenna.
10
The DAB signals are too weak.
Use the TUNE AID feature to locate the best
positioning of the indoor DAB/FM antenna and this
unit for optimal DAB reception.
30
The DAB station
information does not
appear or is
inaccurate.
The DAB station is temporarily out of
service, or the DAB station information
is not provided by the DAB broadcaster.
Contact the DAB broadcaster.
—
FM reception
Problem
FM stereo reception is
noisy.
Cause
Remedy
Page
The antenna is connected improperly.
Check the antenna connections.
10
The characteristics of FM stereo
broadcasts cause this problem when the
transmitter is too far away or the
antenna input is poor.
Try using a high-quality directional FM antenna.
—
Switch to monaural mode.
28
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
Use a high-quality directional FM antenna.
—
Use the manual tuning method.
28
The preset selecting
function does not
work.
The preset (memory) has been erased.
Preset radio stations again.
28
There is distortion,
and clear reception
cannot be obtained
even with a good FM
antenna or an outdoor
antenna.
Multipath reflection or other radio
interference has occurred.
Change the height, direction, or placement of the
antenna.
—
iPod
Note
In case of a transmission error without a status message appearing on the front panel display of this unit, check the connection to your
iPod (refer to page 11).
Status message
Cause
Remedy
Page
READING
This unit is in the middle of recognizing
the connection with the iPod.
If the message continues to appear on the front panel
display and playback does not start, connect the iPod
again.
—
UNKNOWN
There is a problem with the signal path
from the iPod to this unit.
Connect the iPod again.
11
The iPod being used is not supported by
this unit.
Only iPod classic, iPod nano (2nd, 3rd, 4th, 5th and
6th generation), iPod touch (1st, 2nd, 3rd, and 4th
generation), iPhone, iPhone 3G/3GS, iPhone 4, and
iPad are supported.
11
The iPod software is out of date.
Update the iPod software version to the latest.
—
Connect the iPod and this unit by a USB cable
correctly.
11
STOP
The play back of the iPod is finished.
For example, all the songs in the
selected album have finished being
played back.
NO iPod
The iPod was disconnected from this
unit.
46 En
TROUBLESHOOTING
Problem
No sound.
Cause
Remedy
Page
The power of this unit is off.
Connect the power cable correctly.
11
The iPod software version has not been
updated.
Download the latest iTunes software to update the
iPod software version to the latest.
—
The iPod is in the process of connecting
with this unit.
Please wait for a while.
—
The iPod is not connected correctly.
Connect the iPod and this unit by a USB cable
correctly.
11
No sound of your
iPod from the TV.
No sound of your iPod can be output
from this unit to the TV through the
HDMI cable.
Use the speakers of this unit.
—
This unit cannot be
operated by the
remote control.
The iPod is not supported by this unit.
Only iPod classic, iPod nano (2nd, 3rd, 4th, 5th and
6th generation), iPod touch (1st, 2nd, 3rd, and 4th
generation), iPhone, iPhone 3G/3GS, iPhone 4, and
iPad are supported.
11
The iPod is not connected correctly.
Connect the iPod and this unit by a USB cable
correctly.
11
The iPod software version is out of date.
Update the iPod software version to the latest. If the
problem cannot be solved, even with the latest
software, reset the iPod.
—
You cannot operate
from the iPod.
The iPod is not connected correctly.
Connect the iPod and this unit by a USB cable
correctly.
11
The playback
information is not
displayed on the
front panel display.
The iPod you set is not compatible with
the playback information display.
Only iPod classic, iPod nano (2nd, 3rd, 4th, 5th and
6th generation), iPod touch (1st, 2nd, 3rd, and 4th
generation), iPhone, iPhone 3G/3GS, iPhone 4, and
iPad are supported.
11
The iPod does not
charge up.
The iPod is not connected correctly.
Connect the iPod and this unit by a USB cable
correctly.
11
The iPod is not supported by this unit.
Only iPod classic, iPod nano (2nd, 3rd, 4th, 5th and
6th generation), iPod touch (1st, 2nd, 3rd, and 4th
generation), iPhone, iPhone 3G/3GS, iPhone 4, and
iPad are supported.
11
No sound.
The iPod sounds, but
you cannot operate it
with this unit or the
remote control.
Note
In case of a transmission error without a status message appearing on the front panel of this unit, check the connection to the USB
device (refer to page 13).
Status message
USB ERROR
Cause
The connected USB device is not
playable on this unit.
The USB device is connected at an
angle.
Remedy
Disconnect the USB device. Change input source
other than USB and select USB as input source
again. Then connect playable USB device again.
ADDITIONAL
INFORMATION
USB
Page
13
English
47 En
TROUBLESHOOTING
Problem
The file in the USB
device does not play.
Cause
The USB device is not recognized.
Remedy
Page
Connect the USB device again.
13
Connect an AC adapter if supplied with the device.
—
Incorrect USB device connections.
Connect the USB device again.
13
The file format is not compatible with
this unit.
Replace the file with a correctly recorded file
playable with this unit.
3
If the solutions above do not resolve the
problem, the USB device is not playable
on this unit.
Try another USB device.
—
Disc playback
■ General
Problem
Remedy
Page
Check that the sampling rate and bit rate of an audio
or video file are compatible with this unit.
3
Audio may not be output depending on the audio
recording status, such as when audio other than an
audio signal or non-standard audio is recorded for
the audio content.
3
There is no sound during still mode, slow motion
playback, fast forward and fast reverse.
—
The disc is not finalized.
The CD-R/RW, DVD+R/RW/R DL, and DVD-R/
RW/R DL must be finalized.
3
Disc is loaded upside-down.
Remove the disc and then load the disc with the
labeled side facing up.
—
The disc is defective.
Try playing back another disc. If this solves the
problem, the disc you want to play back is defective.
—
The format of the file is not compatible
with this unit.
Check that the format of the file is compatible with
this unit.
3
Some button
operations do not
work.
The disc loaded into this unit is not
compatible.
Use a disc supported by this unit.
3
Playback does not
start immediately
after pressing
on this unit or
on
the remote control.
The disc is dirty.
Remove the disc and then wipe the disc clean.
4
The disc loaded into this unit is not
compatible.
Use a disc supported by this unit.
3
If this unit was moved from a cold to
warm place, condensation has formed on
the disc reading lens.
Wait for an hour or two until this unit adjusts to the
room temperature, and try again.
—
The disc loaded into this unit is not
compatible.
Use a disc supported by this unit.
3
The disc is dirty.
Remove the disc and then wipe the disc clean.
4
Disc is loaded upside-down.
Remove the disc and then load the disc with the
labeled side facing up.
—
The disc is a copyright-protected disc.
The audio may not be output or the images may not
be played back properly for some discs in which
copyright-protected contents are recorded.
—
No sound or
distorted sound.
Disc playback does
not start.
[No Disc] appears in
the display even
though a disc is in
the disc tray.
Audio is not output,
or images are not
played back properly.
48 En
Cause
The sampling rate of an audio or video
file is not compatible with this unit.
TROUBLESHOOTING
■ Picture
Problem
Screen freezes and
operation buttons do
not work.
Cause
Remedy
Press
This unit needs to be restarted.
, then restart playback.
Page
—
Turn off the power and turn on the power again.
—
Press and hold
on the front panel for around 5
seconds to restart this unit.
—
Video is not output
with the desired
resolution.
Resolution is set incorrectly.
Set to the desired resolution.
39
Wide-screen video
appears vertically
stretched, or black
bands appear at the
top and bottom of the
screen. Or 4:3 video
appears horizontally
stretched.
Aspect ratio of your TV is set incorrectly.
Change the aspect ratio of your TV.
39
Blocks in images may be visible in scenes with rapid
movement due to the characteristics of digital image
compression technology.
—
This unit complies with analog copy protection.
Some discs contain a copy prohibiting signal. If you
try to play back such discs through a VCR, or record
to a VCR and play back the signal, the copy
protection will prevent normal playback.
—
Remedy
Page
Square noise
(mosaic) appears on
the screen.
The playback screen
will be disturbed if
DVD video is
recorded to a VCR, or
played back through
a VCR.
The disc is a copyright-protected disc.
Remote control
Problem
The remote control
does not work nor
function properly.
Cause
For information on the remote control operation
range, refer to “Using the remote control”.
9
The remote control sensor on this unit is
exposed to direct sunlight or lighting.
Change the lighting or orientation of this unit.
—
The battery is worn out.
Replace the battery with new one.
9
There are obstacles between the sensor of
this unit and the remote control.
Remove the obstacles.
—
Network
Problem
Cannot connect to
the Internet.
Cause
Remedy
ADDITIONAL
INFORMATION
The remote control is operated outside its
operation range.
Page
Incorrect cable connections.
Connect the Network cable properly.
13
The connected equipment is turned off.
Turn on the connected equipment, such as the
broadband router or modem.
—
Connections of the broadband router and/
or modem are incorrect.
Connect the broadband router and/or modem
correctly.
—
The network setting is incorrect.
Set the proper value(s) in the network setting. Refer
to “Network”.
38
English
49 En
TROUBLESHOOTING
Problem
Cannot download
BD-Live contents.
Cannot detect the
DLNA server.
Cannot play the file
on the home network
server.
Cause
Remedy
Page
Incorrect cable connections.
Connect the Network cable properly.
13
Incorrect USB device connections.
Connect the USB memory device properly. Check
that the USB memory device is connected to the
USB port of this unit.
13
The BD disc does not support BD-Live.
Check if the BD disc supports BD-Live.
—
The network setting is incorrect.
Check the setting for [Internet Connection].
38
The USB memory device is not
compatible.
Connect the USB memory device formatted in
FAT16 or FAT32.
13
There is insufficient free space on the
USB memory device.
It is recommended to connect the USB memory
device with at least 2 GB of free space. If there is not
enough free space, format the USB memory device.
37
Refer to the supplied user’s manual of the disc or
consult the disc manufacturer.
—
Incorrect cable connections.
Connect the network cable properly.
13
The connected equipment is turned off.
Turn on the connected equipment, such as the
broadband router or the server.
—
The access point of this unit and the
server are not the same.
Confirm this unit and the server are connected to the
same access point.
—
The network setting is incorrect.
Set the proper value(s) in the network setting. Refer
to “Network”.
38
The DLNA server does not permit this
unit.
Depending on the DLNA server, this unit may need
to be permitted from the server.
—
The file is not supported by this unit.
Make sure the file is playable.
3
The DLNA setting is incorrect.
Check your DLNA server’s setting.
38
The playback and operating quality may be affected
by your home network condition.
—
Messages on the screen
The following messages appear on the TV screen in case the disc you tried to play back is not appropriate or the
operation is not correct.
Error message
Cause
Remedy
Page
Unsupported File
The file is not supported by this unit.
Refer to “Types of discs/files that can be used with
this unit”.
3
Wrong region code!
The disc is an incompatible region code.
Refer to “Region management information”.
3
Network has FAILED.
This unit cannot be connected to the
network.
Check connection and Network setting.
13
38
Network is OK, proxy
has FAILED.
This unit cannot be connected to the
proxy server.
Refer to “[Proxy Setting]”.
38
BD-Live connection
is prohibited in
SETUP menu.
BD-Live connection is prohibited.
Refer to “[BD-Live Connection]”.
38
No valid upgrade file
is found!
The upgrade file cannot be found.
Check if the upgrade file is in the appropriate folder.
—
Upgrade has failed
for some reason!
Upgrade is failed.
Check if the upgrade file is corrupted or unreadable.
—
50 En
TROUBLESHOOTING
Others
Problem
Password is
forgotten.
Cause
Remedy
Page
When no disc is inserted and playback is stopped,
press and hold
and
on the front panel
simultaneously for around 5 seconds to set all the
Security settings (p. 38) of this unit to their default
settings. After the power is turned off automatically,
press
to turn on the power again.
—
ADDITIONAL
INFORMATION
English
51 En
GLOSSARY
AIR SURROUND XTREME
AVCHD
This unit employs new technologies and algorithms that
make it possible to achieve 5-channel surround sound
with only front speakers, and without using wall
reflections.
Ordinarily, two front speakers, a center speaker, two
surround speakers, and a subwoofer are necessary for
enjoying 5.1 channel surround sound.
AVCHD is a new format (standard) for high definition
video cameras that can be used to record and play highresolution HD images.
BD-Live™
BD-Live is a BD standard that utilizes a network
connection, enabling this unit to go online to download
promotional videos and other data.
BDMV
Typical 5.1 channel speaker system
Front speakers
Subwoofer
BDMV (Blu-ray Disc Movie, BD-MV) refers to one of
the application formats used for BD-ROM which is one
of the Blu-ray Disc specifications. BDMV is a recording
format equivalent to DVD-Video of the DVD
specification.
Blu-ray 3D™
Blu-ray 3D enables you to view full high definition 3D
images.
Center
speaker
Surround speakers
Virtual 5.1 channel
The AIR SURROUND XTREME technology, using
only front speakers, enables you to enjoy a realistic 5.1
channel sound by simulating sound from virtual
speakers at center and surround.
The sound image of this unit
BONUSVIEW™
BONUSVIEW compatible discs let you simultaneously
enjoy video sub-channel for two screens, audio subchannel and sub-titles. A small screen appears within
the main screen during playback (Picture in Picture).
Closed caption
Closed captions are kind of subtitle, and the difference
between subtitles and captions is that subtitles are
intended for hearing persons and captions are for the
hearing impaired. Subtitles rarely show all of the audio.
For example, captions show sound effects (e.g., “phone
ringing” and “footsteps”), while subtitles do not. Before
you select this setting, please ensure that the disc
contains closed caption information.
Color Space
Color Space is a color range that can be represented.
RGB is a color space based on the RGB color model
(red, green and blue) and is typically used for PC
monitors. YCbCr is a color space based on a luminance
signal (Y) and two color difference signals (Cb and Cr).
Deep Color
The system creates the virtual 5.1 channel surround
sound with the speakers.
C: Center speaker
FR, FL: Front speakers
SR, SL: Surround virtual speakers
Deep Color refers to the use of various color depths in
displays, up from the 24-bit depths in previous versions
of the HDMI specification. This extra bit depth allows
HDTVs and other displays go from millions of colors to
billions of colors and eliminate on-screen color banding
for smooth tonal transitions and subtle gradations
between colors. The increased contrast ratio can
represent many times more shades of gray between
black and white. Also Deep Color increases the number
of available colors within the boundaries defined by the
RGB or YCbCr color space.
Dolby Digital
A sound system developed by Dolby Laboratories Inc.
that gives movie theater ambience to audio output when
the product is connected to a Dolby Digital processor or
amplifier.
52 En
GLOSSARY
Dolby Digital Plus
A sound system developed as an extension to Dolby
Digital. This audio coding technology supports 7.1
multi-channel surround sound.
Dolby TrueHD
Dolby TrueHD is a lossless coding technology that
supports up to 8 channels of multi-channel surround
sound for the next generation optical discs. The
reproduced sound is true to the original source bit-forbit.
DRC (Dynamic Range Control)
DRC lets you adjust the range between the loudest and
softest sounds (dynamic range) for playback at average
volume. Use this when it is hard to hear dialog, or
during times when playback may disturb neighbors.
DTS
This is a digital sound system developed by DTS, Inc.
for use in cinemas.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is a new technology
developed for the next generation high definition optical
disc format.
Mac address
The Mac address is a unique value assigned to a network
device for identification purposes.
Pan Scan (PS 4:3)
A screen size that cuts off the sides of the image to allow
viewing of wide-screen (16:9) material on a connected
4:3 TV.
Subtitles
These are the lines of text appearing at the bottom of the
screen which translate or transcribe the dialog. They are
recorded on many DVD and BD discs.
Top menu
In a BD-Video/DVD-Video, this is the menu for
selecting things like the chapter to be played back and
the subtitle language. In some DVD-Videos, the top
menu may be called the “Title Menu”.
x.v.Color
x.v.Color reproduces a greater range of color than
before, showing almost all of the colors that the human
eye can detect.
HDMI
HDMI (High-Definition Multimedia Interface) is an
interface that supports both video and audio on a single
digital connection. The HDMI connection carries
standard to high definition video signals and multichannel audio signals to AV components such as HDMI
equipped TVs, in digital form without degradation.
Letterbox (LB 4:3)
A screen size with black bars on the top and bottom of
the image to allow viewing of wide-screen (16:9)
material on a connected 4:3 TV.
Linear PCM Sound
ADDITIONAL
INFORMATION
Linear PCM is a signal recording format used for Audio
CDs and on some DVD and Blu-ray discs. The sound on
Audio CDs is recorded at 44.1 kHz with 16 bits. (Sound
is recorded between 48 kHz with 16 bits and 96 kHz
with 24 bits on DVD discs and between 48 kHz with 16
bits and 192 kHz with 24 bits on BD discs.)
Lip Sync
Lip Sync, an abbreviation for lip synchronization, is a
technical term that involves both a problem and a
capability of maintaining audio and video signals
synchronized during post-production and transmission.
Whereas the audio and video latency requires complex
end-user adjustments, HDMI incorporates an automatic
audio and video syncing capability that allows devices
to perform this synchronization automatically and
accurately without user interaction.
English
53 En
SPECIFICATIONS
PLAYER SECTION
iPod/iPhone/iPad
• Supported iPod/iPhone/iPad ....................................... iPod classic,
iPod nano (2nd, 3rd, 4th, 5th and 6th generation),
iPod touch (1st, 2nd, 3rd, and 4th generation),
iPhone, iPhone 3G/3GS, iPhone 4, iPad
disc and file formats
• For supported disc and file formats, refer to page 3.
AUX
• Input connector
AUX ........................................................................................ RCA
AMPLIFIER SECTION
• Maximum output power............................................ 30 W + 30 W
(1 kHz, 10% THD, 6 Ω)
• Input sensitivity/Input impedance
AUX ........................................................................ 400 mV/47 kΩ
• Total harmonic distortion
AUX 1 kHz/10 W................................................................. 0.05 %
TUNER SECTION
• Tuning range
DAB .....................................................174 to 240 MHz (Band III)
FM ................................................................. 87.50 to 108.00 MHz
INPUT/OUTPUT
• HDMI output ................................................Type A connector × 1
480i/576i, 480p/576p, 720p, 1080i, 1080p, 1080p/24Hz,
Deep Color, x.v.Color, 3D,
ARC(Audio Return Channel) support
• Video output .............................................................1 Vp-p (75 Ω)
• USB ..............................................................Type A connector × 2
• Other equipment .......................................................... Ethernet × 1
GENERAL
• Power Supply
[Europe model] .................................... AC 220-240 V, 50/60 Hz
[Asia model] ........................................ AC 220-240 V, 50/60 Hz
[Australia model]..............................................AC 240 V, 50 Hz
[U.K. model].....................................................AC 230 V, 50 Hz
[China model] ...................................... AC 220-240 V, 50/60 Hz
[Korea model]...................................................AC 220 V, 60 Hz
[Russia model]..................................... AC 220-240 V, 50/60 Hz
[Central and South America model].... AC 100-120 V, 50/60 Hz
• Power consumption ................................................................ 56 W
• Standby Power consumption ......................................0.5 W or less
• Dimensions (W × H × D, including protrusions)
................................................................. 215 × 114.5 × 306.3 mm
(8 1/2 × 4 5/8 × 12 1/8 in)
• Weight ................................................................... 3.0 kg (6.6 lbs.)
Specifications are subject to change without notice.
Information for Users on Collection and Disposal of Old Equipment
and Used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC
and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent
any potential negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
54 En
SPECIFICATIONS
■ Copyright
• iPad, iPhone, iPod, iPod classic, iPod nano, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries.
“Made for iPod,” “Made for iPhone,” and “Made for iPad”
mean that an electronic accessory has been designed to connect
specifically to iPod, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone, or
iPad may affect wireless performance.
• Manufactured under license under U.S. Patent Nos: 5,956,674;
5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and worldwide patents
issued & pending. DTS-HD, the Symbol, & DTS-HD and the
Symbol together are registered trademarks of DTS, Inc.
Product includes software. © DTS, Inc. All Rights Reserved.
• Blu-ray DiscTM, Blu-rayTM, Blu-ray 3DTM, BD-LiveTM,
BONUSVIEWTM, and the logos are trademarks of the Blu-ray
Disc Association.
• Audio-visual material may consist of copyrighted works which
must not be recorded without the authority of the owner of the
copyright. Refer to relevant laws in your country.
• This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized
by Rovi Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by Rovi
Corporation. Reverse engineering or disassembly is prohibited.
• This product is licensed under the AVC patent portfolio license
and VC-1 patent portfolio license for the personal and noncommercial use of a consumer to (i) encode video in
compliance with the AVC Standard and VC-1 Standard
(“AVC/VC-1 Video”) and/or (ii) decode AVC/VC-1 Video
that was encoded by a consumer engaged in a personal and
non-commercial activity and/or was obtained from a video
provider licensed to provide AVC/VC-1 Video. No license is
granted or shall be implied for any other use. Additional
information may be obtained from MPEG LA, LLC.
See http://www.mpegla.com.
• “x.v.Color” and “x.v.Color” logo are trademarks.
• “AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
• Java and all Java-based trademarks and logos are trademarks
or registered trademarks of Sun Microsystems, Inc. in the
United States and/or other countries.
• YouTube and the YouTube logo are trademarks of Google.
Inc.
•
is a trademark of DVD Format/Logo Licensing
Corporation.
• Manufactured under license from Dolby Laboratories. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories.
ADDITIONAL
INFORMATION
• Windows Media Player is a registered trademark or trademark
of Microsoft corporation in the United States and/or other
countries.
• HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
• DLNA and DLNA CERTIFIED are trademarks and/or service
marks of Digital Living Network Alliance.
• This unit employs new technologies and algorithms that make
it possible to achieve 5-channel surround sound with only front
speakers, and without using wall reflections.
English
• This unit supports DAB/DAB+ tuning.
55 En
Information about software
This product uses the following software.
For information (copyright, etc) about each software, read the original sentences stated below.
■ About Linux, Busybox, SquashFS, LIRC, U-boot
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document,
but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and
change it. By contrast, the GNU General Public License is intended to guarantee your
freedom to share and change free software--to make sure the software is free for all its
users. This General Public License applies to most of the Free Software Foundation’s
software and to any other program whose authors commit to using it. (Some other Free
Software Foundation software is covered by the GNU Library General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General
Public Licenses are designed to make sure that you have the freedom to distribute
copies of free software (and charge for this service if you wish), that you receive source
code or can get it if you want it, that you can change the software or use pieces of it in
new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you
these rights or to ask you to surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you
must give the recipients all the rights that you have. You must make sure that they, too,
receive or can get the source code. And you must show them these terms so they know
their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this
license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone
understands that there is no warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients to know that what they have is
not the original, so that any problems introduced by others will not reflect on the
original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to
avoid the danger that redistributors of a free program will individually obtain patent
licenses, in effect making the program proprietary. To prevent this, we have made it
clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work which contains a notice placed
by the copyright holder saying it may be distributed under the terms of this General
Public License. The “Program”, below, refers to any such program or work, and a
“work based on the Program” means either the Program or any derivative work
under copyright law: that is to say, a work containing the Program or a portion of it,
either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term “modification”.)
Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this
License; they are outside its scope. The act of running the Program is not restricted,
and the output from the Program is covered only if its contents constitute a work
based on the Program (independent of having been made by running the Program).
Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you
receive it, in any medium, provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice and disclaimer of warranty;
keep intact all the notices that refer to this License and to the absence of any
warranty; and give any other recipients of the Program a copy of this License along
with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at
your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus
forming a work based on the Program, and copy and distribute such modifications
or work under the terms of Section 1 above, provided that you also meet all of these
conditions:
a) You must cause the modified files to carry prominent notices stating that you
changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part
contains or is derived from the Program or any part thereof, to be licensed as a
whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you
must cause it, when started running for such interactive use in the most
ordinary way, to print or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or else, saying that you
provide a warranty) and that users may redistribute the program under these
conditions, and telling the user how to view a copy of this License. (Exception:
if the Program itself is interactive but does not normally print such an
announcement, your work based on the Program is not required to print an
announcement.)
i
These requirements apply to the modified work as a whole. If identifiable sections of
that work are not derived from the Program, and can be reasonably considered
independent and separate works in themselves, then this License, and its terms, do not
apply to those sections when you distribute them as separate works. But when you
distribute the same sections as part of a whole which is a work based on the Program,
the distribution of the whole must be on the terms of this License, whose permissions
for other licensees extend to the entire whole, and thus to each and every part regardless
of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work
written entirely by you; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the
Program (or with a work based on the Program) on a volume of a storage or distribution
medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2)
in object code or executable form under the terms of Sections 1 and 2 above
provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code,
which must be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any
third party, for a charge no more than your cost of physically performing source
distribution, a complete machine-readable copy of the corresponding source
code, to be distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute
corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object
code or executable form with such an offer, in accord with Subsection b
above.)
The source code for a work means the preferred form of the work for making
modifications to it. For an executable work, complete source code means all the source
code for all modules it contains, plus any associated interface definition files, plus the
scripts used to control compilation and installation of the executable. However, as a
special exception, the source code distributed need not include anything that is
normally distributed (in either source or binary form) with the major components
(compiler, kernel, and so on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a
designated place, then offering equivalent access to copy the source code from the same
place counts as distribution of the source code, even though third parties are not
compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as
expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate your
rights under this License. However, parties who have received copies, or rights,
from you under this License will not have their licenses terminated so long as such
parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However,
nothing else grants you permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if you do not accept this
License. Therefore, by modifying or distributing the Program (or any work based
on the Program), you indicate your acceptance of this License to do so, and all its
terms and conditions for copying, distributing or modifying the Program or works
based on it.
6. Each time you redistribute the Program (or any work based on the Program), the
recipient automatically receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms and conditions. You may
not impose any further restrictions on the recipients’ exercise of the rights granted
herein. You are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for
any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of
this License, they do not excuse you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously your obligations under this License
and any other pertinent obligations, then as a consequence you may not distribute
the Program at all. For example, if a patent license would not permit royalty-free
redistribution of the Program by all those who receive copies directly or indirectly
through you, then the only way you could satisfy both it and this License would be
to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular
circumstance, the balance of the section is intended to apply and the section as a whole
is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other
property right claims or to contest validity of any such claims; this section has the sole
purpose of protecting the integrity of the free software distribution system, which is
implemented by public license practices. Many people have made generous
contributions to the wide range of software distributed through that system in reliance
on consistent application of that system; it is up to the author/donor to decide if he or
she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence
of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either
by patents or by copyrighted interfaces, the original copyright holder who places
the Program under this License may add an explicit geographical distribution
limitation excluding those countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this License incorporates the
limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the
General Public License from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the Program specifies a
version number of this License which applies to it and “any later version”, you have the
option of following the terms and conditions either of that version or of any later
version published by the Free Software Foundation. If the Program does not specify a
version number of this License, you may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose
distribution conditions are different, write to the author to ask for permission. For
software which is copyrighted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this. Our decision will be
guided by the two goals of preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the
public, the best way to achieve this is to make it free software which everyone can
redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the
start of each source file to most effectively convey the exclusion of warranty; and each
file should have at least the “copyright” line and a pointer to where the full notice is
found.
<one line to give the program’s name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public License along with
this program; if not, write to the Free Software Foundation, Inc., 51 Franklin St,
Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this
when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes
with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free
software, and you are welcome to redistribute it under certain conditions; type
‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts
of the General Public License. Of course, the commands you use may be called
something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu
items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if
any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
‘Gnomovision’ (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may consider it more
useful to permit linking proprietary applications with the library. If this is what you
want to do, use the GNU Library General
Public License instead of this License..
■ About glibc, libmtp, libusb, libusb-compat, DirectFB
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies of this license document,
but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of
the GNU Library Public License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and
change it. By contrast, the GNU General Public Licenses are intended to guarantee
your freedom to share and change free software--to make sure the software is free for
all its users.
This license, the Lesser General Public License, applies to some specially designated
software packages--typically libraries--of the Free Software Foundation and other
authors who decide to use it. You can use it too, but we suggest you first think carefully
about whether this license or the ordinary General Public License is the better strategy
to use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our
General Public Licenses are designed to make sure that you have the freedom to
distribute copies of free software (and charge for this service if you wish); that you
receive source code or can get it if you want it; that you can change the software and
use pieces of it in new free programs; and that you are informed that you can do these
things.
To protect your rights, we need to make restrictions that forbid distributors to deny you
these rights or to ask you to surrender these rights. These restrictions translate to
certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must
give the recipients all the rights that we gave you. You must make sure that they, too,
receive or can get the source code. If you link other code with the library, you must
provide complete object files to the recipients, so that they can relink them with the
library after making changes to the library and recompiling it. And you must show
them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we
offer you this license, which gives you legal permission to copy, distribute and/or
modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for
the free library. Also, if the library is modified by someone else and passed on, the
recipients should know that what they have is not the original version, so that the
original author’s reputation will not be affected by problems that might be introduced
by others.
Finally, software patents pose a constant threat to the existence of any free program.
We wish to make sure that a company cannot effectively restrict the users of a free
program by obtaining a restrictive license from a patent holder. Therefore, we insist
that any patent license obtained for a version of the library must be consistent with the
full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General
Public License. This license, the GNU Lesser General Public License, applies to
certain designated libraries, and is quite different from the ordinary General Public
License. We use this license for certain libraries in order to permit linking those
libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the
combination of the two is legally speaking a combined work, a derivative of the original
library. The ordinary General Public License therefore permits such linking only if the
entire combination fits its criteria of freedom. The Lesser General Public License
permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does Less to protect
the user’s freedom than the ordinary General Public License. It also provides other free
software developers Less of an advantage over competing non-free programs. These
disadvantages are the reason we use the ordinary General Public License for many
libraries. However, the Lesser license provides advantages in certain special
circumstances.
For example, on rare occasions, there may be a special need to encourage the widest
possible use of a certain library, so that it becomes a de-facto standard. To achieve this,
non-free programs must be allowed to use the library. A more frequent case is that a
free library does the same job as widely used non-free libraries. In this case, there is
little to gain by limiting the free library to free software only, so we use the Lesser
General Public License.
In other cases, permission to use a particular library in non-free programs enables a
greater number of people to use a large body of free software. For example, permission
to use the GNU C Library in non-free programs enables many more people to use the
whole GNU operating system, as well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users’ freedom, it
does ensure that the user of a program that is linked with the Library has the freedom
and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow.
Pay close attention to the difference between a “work based on the library” and a “work
that uses the library”. The former contains code derived from the library, whereas the
latter must be combined with the library in order to run.
ii
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License Agreement applies to any software library or other program which
contains a notice placed by the copyright holder or other authorized party saying it
may be distributed under the terms of this Lesser General Public License (also
called “this License”). Each licensee is addressed as “you”.
A “library” means a collection of software functions and/or data prepared so as to be
conveniently linked with application programs (which use some of those functions and
data) to form executables.
The “Library”, below, refers to any such software library or work which has been
distributed under these terms. A “work based on the Library” means either the Library
or any derivative work under copyright law: that is to say, a work containing the
Library or a portion of it, either verbatim or with modifications and/or translated
straightforwardly into another language. (Hereinafter, translation is included without
limitation in the term “modification”.)
“Source code” for a work means the preferred form of the work for making
modifications to it. For a library, complete source code means all the source code for
all modules it contains, plus any associated interface definition files, plus the scripts
used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this
License; they are outside its scope. The act of running a program using the Library is
not restricted, and output from such a program is covered only if its contents constitute
a work based on the Library (independent of the use of the Library in a tool for writing
it). Whether that is true depends on what the Library does and what the program that
uses the Library does.
1. You may copy and distribute verbatim copies of the Library’s complete source
code as you receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice and disclaimer
of warranty; keep intact all the notices that refer to this License and to the absence
of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your
option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus
forming a work based on the Library, and copy and distribute such modifications or
work under the terms of Section 1 above, provided that you also meet all of these
conditions:
If distribution of object code is made by offering access to copy from a designated
place, then offering equivalent access to copy the source code from the same place
satisfies the requirement to distribute the source code, even though third parties are not
compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed
to work with the Library by being compiled or linked with it, is called a “work that
uses the Library”. Such a work, in isolation, is not a derivative work of the Library,
and therefore falls outside the scope of this License.
However, linking a “work that uses the Library” with the Library creates an executable
that is a derivative of the Library (because it contains portions of the Library), rather
than a “work that uses the library”. The executable is therefore covered by this License.
Section 6 states terms for distribution of such executables.
When a “work that uses the Library” uses material from a header file that is part of the
Library, the object code for the work may be a derivative work of the Library even
though the source code is not. Whether this is true is especially significant if the work
can be linked without the Library, or if the work is itself a library. The threshold for
this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and
accessors, and small macros and small inline functions (ten lines or less in length), then
the use of the object file is unrestricted, regardless of whether it is legally a derivative
work. (Executables containing this object code plus portions of the Library will still
fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code
for the work under the terms of Section 6. Any executables containing that work also
fall under Section 6, whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link a ‘work that
uses the Library” with the Library to produce a work containing portions of the
Library, and distribute that work under terms of your choice, provided that the
terms permit modification of the work for the customer’s own use and reverse
engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in
it and that the Library and its use are covered by this License. You must supply a copy
of this License. If the work during execution displays copyright notices, you must
include the copyright notice for the Library among them, as well as a reference
directing the user to the copy of this License. Also, you must do one of these things:
c) You must cause the whole of the work to be licensed at no charge to all third
parties under the terms of this License.
a) Accompany the work with the complete corresponding machine-readable
source code for the Library including whatever changes were used in the work
(which must be distributed under Sections 1 and 2 above); and, if the work is an
executable linked with the Library, with the complete machine-readable “work
that uses the Library”, as object code and/or source code, so that the user can
modify the Library and then relink to produce a modified executable containing
the modified Library. (It is understood that the user who changes the contents
of definitions files in the Library will not necessarily be able to recompile the
application to use the modified definitions.)
d) If a facility in the modified Library refers to a function or a table of data to be
supplied by an application program that uses the facility, other than as an
argument passed when the facility is invoked, then you must make a good faith
effort to ensure that, in the event an application does not supply such function
or table, the facility still operates, and performs whatever part of its purpose
remains meaningful.
b) Use a suitable shared library mechanism for linking with the Library. A
suitable mechanism is one that (1) uses at run time a copy of the library already
present on the user’s computer system, rather than copying library functions
into the executable, and (2) will operate properly with a modified version of the
library, if the user installs one, as long as the modified version is interfacecompatible with the version that the work was made with.
(For example, a function in a library to compute square roots has a purpose that is
entirely well-defined independent of the application. Therefore, Subsection 2d
requires that any application-supplied function or table used by this function must
be optional: if the application does not supply it, the square root function must still
compute square roots.)
c) Accompany the work with a written offer, valid for at least three years, to give
the same user the materials specified in Subsection 6a, above, for a charge no
more than the cost of performing this distribution.
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you
changed the files and the date of any change.
These requirements apply to the modified work as a whole. If identifiable sections of
that work are not derived from the Library, and can be reasonably considered
independent and separate works in themselves, then this License, and its terms, do not
apply to those sections when you distribute them as separate works. But when you
distribute the same sections as part of a whole which is a work based on the Library, the
distribution of the whole must be on the terms of this License, whose permissions for
other licensees extend to the entire whole, and thus to each and every part regardless of
who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work
written entirely by you; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library
(or with a work based on the Library) on a volume of a storage or distribution medium
does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License
instead of this License to a given copy of the Library. To do this, you must alter all
the notices that refer to this License, so that they refer to the ordinary GNU General
Public License, version 2, instead of to this License. (If a newer version than
version 2 of the ordinary GNU General Public License has appeared, then you can
specify that version instead if you wish.) Do not make any other change in these
notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary
GNU General Public License applies to all subsequent copies and derivative works
made from that copy.
This option is useful when you wish to copy part of the code of the Library into a
program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under
Section 2) in object code or executable form under the terms of Sections 1 and 2
above provided that you accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of Sections 1 and 2
above on a medium customarily used for software interchange.
iii
d) If distribution of the work is made by offering access to copy from a designated
place, offer equivalent access to copy the above specified materials from the
same place.
e) Verify that the user has already received a copy of these materials or that you
have already sent this user a copy.
For an executable, the required form of the “work that uses the Library” must include
any data and utility programs needed for reproducing the executable from it. However,
as a special exception, the materials to be distributed need not include anything that is
normally distributed (in either source or binary form) with the major components
(compiler, kernel, and so on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other
proprietary libraries that do not normally accompany the operating system. Such a
contradiction means you cannot use both them and the Library together in an executable
that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in
a single library together with other library facilities not covered by this License,
and distribute such a combined library, provided that the separate distribution of the
work based on the Library and of the other library facilities is otherwise permitted,
and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the
Library, uncombined with any other library facilities. This must be distributed
under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a
work based on the Library, and explaining where to find the accompanying
uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as
expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense, link with, or distribute the Library is void, and will automatically
terminate your rights under this License. However, parties who have received
copies, or rights, from you under this License will not have their licenses
terminated so long as such parties remain in full compliance.
9. You are not required to accept this License, since you have not signed it. However,
nothing else grants you permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if you do not accept this
License. Therefore, by modifying or distributing the Library (or any work based on
the Library), you indicate your acceptance of this License to do so, and all its terms
and conditions for copying, distributing or modifying the Library or works based
on it.
10. Each time you redistribute the Library (or any work based on the Library), the
recipient automatically receives a license from the original licensor to copy,
distribute, link with or modify the Library subject to these terms and conditions.
You may not impose any further restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing compliance by third parties
with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for
any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of
this License, they do not excuse you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously your obligations under this License
and any other pertinent obligations, then as a consequence you may not distribute
the Library at all. For example, if a patent license would not permit royalty-free
redistribution of the Library by all those who receive copies directly or indirectly
through you, then the only way you could satisfy both it and this License would be
to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular
circumstance, the balance of the section is intended to apply, and the section as a whole
is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other
property right claims or to contest validity of any such claims; this section has the sole
purpose of protecting the integrity of the free software distribution system which is
implemented by public license practices. Many people have made generous
contributions to the wide range of software distributed through that system in reliance
on consistent application of that system; it is up to the author/donor to decide if he or
she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence
of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either
by patents or by copyrighted interfaces, the original copyright holder who places
the Library under this License may add an explicit geographical distribution
limitation excluding those countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this License incorporates the
limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the
Lesser General Public License from time to time. Such new versions will be similar
in spirit to the present version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the Library specifies a
version number of this License which applies to it and “any later version”, you have the
option of following the terms and conditions either of that version or of any later
version published by the Free Software Foundation. If the Library does not specify a
license version number, you may choose any version ever published by the Free
Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose
distribution conditions are incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the Free Software Foundation,
write to the Free Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing and reuse of software
generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE
LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH
ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the
public, we recommend making it free software that everyone can redistribute and
change. You can do so by permitting redistribution under these terms (or, alternatively,
under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library. It is safest to attach
them to the start of each source file to most effectively convey the exclusion of
warranty; and each file should have at least the “copyright” line and a pointer to where
the full notice is found.
<one line to give the library’s name and a brief idea of what it does.> Copyright (C)
<year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms
of the GNU Lesser General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public
License for more details.
You should have received a copy of the GNU Lesser General Public License along
with this library; if not, write to the Free Software Foundation, Inc., 59 Temple
Place, Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if
any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a
library for tweaking knobs) written by James Random Hacker.
<signature of Ty Coon>, 1 April 1990 Ty Coon, President of Vice
That’s all there is to it!
■ About Fusion
DirectFB Fusion kernel module: introduction and API
by Niels Roest
Copyright (C) 2009 Niels Roest
This documentation is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or (at your option) any
later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
General Public License for more details.
You should have received a copy of the GNU General Public License along with this
program; if not, write to the Free Software Foundation, Inc.,
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
For more details see the ?le COPYING in the source distribution of Linux.
■ About openssl
Copyright (C) 1998-2008 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2. 2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display
the following acknowledgment:
“This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to
endorse or promote products derived from this software without prior written
permission. For written permission, please contact openssl-core@openssl.org.
5. Products derived from this software may not be called “OpenSSL” nor may
“OpenSSL” appear in their names without prior written permission of the OpenSSL
Project.
6. Redistributions of any form whatsoever must retain the following
acknowledgment:
‘This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY
EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
THE USE OF THIS SOFTWARE, EVEN IF ADVISEDOF THE POSSIBILITY OF
SUCH DAMAGE.
This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com). This product includes software written by Tim Hudson
(tjh@cryptsoft.com).
iv
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved.
This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following
conditions are aheared to. The following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The
SSL documentation included with this distribution is covered by the same copyright
terms except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not
to be removed. If this package is used in a product, Eric Young should be given
attribution as the author of the parts of the library used. This can be in the form of a
textual message at program startup or in documentation (online or textual) provided
with the package.
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display
the following acknowledgement:
“This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com)” The word ‘cryptographic’ can be left out if the rouines from
the library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from the apps
directory (application code) you must include an acknowledgement:
“This product includes software written by Tim Hudson (tjh@cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The licence and distribution terms for any publically available version or derivative of
this code cannot be changed. i.e. this code cannot simply be copied and put under
another distribution licence [including the GNU Public Licence.]
■ About zlib
Copyright notice:
(C) 1995-2004 Jean-loup Gailly and Mark Adler
This software is provided ‘as-is’, without any express or implied warranty. In no event
will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including
commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you
wrote the original software. If you use this software in a product, an
acknowledgment in the product documentation would be appreciated but is not
required.
2. Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly
Mark Adler
jloup@gzip.org
madler@alumni.caltech.edu
If you use the zlib library in a product, we would appreciate *not* receiving lengthy
legal documents to sign. The sources are provided for free but without warranty of any
kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does
not include third-party code.
If you redistribute modified sources, we would appreciate that you include in the file
ChangeLog history information documenting your changes. Please read the FAQ for
more information on the distribution of modified source versions.
■ About FreeType
The FreeType Project LICENSE
2006-Jan-27
Copyright 1996-2002, 2006 by
David Turner, Robert Wilhelm, and Werner Lemberg
Introduction
The FreeType Project is distributed in several archive packages; some of them may
contain, in addition to the FreeType font engine, various tools and contributions which
rely on, or relate to, the FreeType Project.
This license applies to all files found in such packages, and which do not fall under their
own explicit license. The license affects thus the FreeType font engine, the test
programs, documentation and makefiles, at the very least.
This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group)
licenses, which all encourage inclusion and use of free software in commercial and
freeware products alike. As a consequence, its main points are that:
v
o We don’t promise that this software works. However, we will be interested in any
kind of bug reports. (‘as is’ distribution)
o You can use this software for whatever you want, in parts or full form, without
having to pay us. (‘royalty-free’ usage)
o You may not pretend that you wrote this software. If you use it, or only parts of it, in
a program, you must acknowledge somewhere in your documentation that you have
used the FreeType code. (‘credits’)
We specifically permit and encourage the inclusion of this software, with or without
modifications, in commercial products. We disclaim all warranties covering The
FreeType Project and assume no liability related to The FreeType Project.
Finally, many people asked us for a preferred form for a credit/disclaimer to use in
compliance with this license. We thus encourage you to use the following text:
Portions of this software are copyright (C) <year> The FreeType Project
(www.freetype.org). All rights reserved.
Please replace <year> with the value from the FreeType version you actually use.
Legal Terms
0. Definitions
Throughout this license, the terms ‘package’, ‘FreeType Project’, and ‘FreeType
archive’ refer to the set of files originally distributed by the authors (David Turner,
Robert Wilhelm, and Werner Lemberg) as the ‘FreeType Project’, be they named as
alpha, beta or final release.
‘You’ refers to the licensee, or person using the project, where ‘using’ is a generic term
including compiling the project’s source code as well as linking it to form a ‘program’
or ‘executable’. This program is referred to as ‘a program using the FreeType engine’.
This license applies to all files distributed in the original FreeType Project, including
all source code, binaries and documentation, unless otherwise stated in the file in its
original, unmodified form as distributed in the original archive. If you are unsure
whether or not a particular file is covered by this license, you must contact us to verify
this.
The FreeType Project is copyright (C) 1996-2000 by David Turner, Robert Wilhelm,
and Werner Lemberg. All rights reserved except as specified below.
1. No Warranty
THE FREETYPE PROJECT IS PROVIDED ‘AS IS’ WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE
USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT.
2. Redistribution
This license grants a worldwide, royalty-free, perpetual and irrevocable right and
license to use, execute, perform, compile, display, copy, create derivative works of,
distribute and sublicense the FreeType Project (in both source and object code forms)
and derivative works thereof for any purpose; and to authorize others to exercise some
or all of the rights granted herein, subject to the following conditions:
o Redistribution of source code must retain this license file (‘FTL.TXT’) unaltered;
any additions, deletions or changes to the original files must be clearly indicated in
accompanying documentation. The copyright notices of the unaltered, original files
must be preserved in all copies of source files.
o Redistribution in binary form must provide a disclaimer that states that the software
is based in part of the work of the FreeType Team, in the distribution documentation.
We also encourage you to put an URL to the FreeType web page in your
documentation, though this isn’t mandatory.
These conditions apply to any software derived from or based on the FreeType Project,
not just the unmodified files. If you use our work, you must acknowledge us. However,
no fee need be paid to us.
3. Advertising
Neither the FreeType authors and contributors nor you shall use the name of the other
for commercial, advertising, or promotional purposes without specific prior written
permission.
We suggest, but do not require, that you use one or more of the following phrases to
refer to this software in your documentation or advertising materials: ‘FreeType
Project’, ‘FreeType Engine’, ‘FreeType library’, or ‘FreeType Distribution’.
As you have not signed this license, you are not required to accept it. However, as the
FreeType Project is copyrighted material, only this license, or another one contracted
with the authors, grants you the right to use, distribute, and modify it. Therefore, by
using, distributing, or modifying the FreeType Project, you indicate that you understand
and accept all the terms of this license.
4. Contacts
There are two mailing lists related to FreeType:
o freetype@nongnu.org
Discusses general use and applications of FreeType, as well as future and wanted
additions to the library and distribution. If you are looking for support, start in this list if
you haven’t found anything to help you in the documentation.
o freetype-devel@nongnu.org
Discusses bugs, as well as engine internals, design issues, specific licenses, porting, etc.
Our home page can be found at
http://www.freetype.org
■ About Expat
Copyright (C) 1998, 1999, 2000 Thai Open Source Software Center Ltd
and Clark Cooper
Copyright (C) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the “Software”), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge,
publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or
substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
■ About cURL
COPYRIGHT AND PERMISSION NOTICE
Copyright (C) 1996 - 2009, Daniel Stenberg, <daniel@haxx.se>.
All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose with or
without fee is hereby granted, provided that the above copyright notice and this
permission notice appear in all copies.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO
EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION
OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in
advertising or otherwise to promote the sale, use or other dealings in this Software
without prior written authorization of the copyright holder.
■ About Independent JPEG group
The Independent JPEG Group’s JPEG software
README for release 7 of 27-Jun-2009
This distribution contains the seventh public release of the Independent JPEG Group’s
free JPEG software. You are welcome to redistribute this software and to use it for any
purpose, subject to the conditions under LEGAL ISSUES, below.
This software is the work of Tom Lane, Guido Vollbeding, Philip Gladstone, Bill
Allombert, Jim Boucher, Lee Crocker, Bob Friesenhahn, Ben Jackson, Julian
Minguillon, Luis Ortiz, George Phillips, Davide Rossi, Ge’ Weijers, and other members
of the Independent JPEG Group.
IJG is not affiliated with the official ISO JPEG standards committee.
DOCUMENTATION ROADMAP
This file contains the following sections:
OVERVIEW
General description of JPEG and the IJG software.
LEGAL ISSUES
Copyright, lack of warranty, terms of distribution.
REFERENCES
Where to learn more about JPEG.
ARCHIVE LOCATIONS
Where to find newer versions of this software.
ACKNOWLEDGMENTS
Special thanks.
FILE FORMAT WARS
Software *not* to get.
TO DO
Plans for future IJG releases.
Other documentation files in the distribution are:
User documentation:
install.txt
How to configure and install the IJG software.
usage.txt
Usage instructions for cjpeg, djpeg, jpegtran, rdjpgcom, and
wrjpgcom.
*.1
Unix-style man pages for programs (same info as usage.txt).
wizard.txt
Advanced usage instructions for JPEG wizards only.
change.log
Version-to-version change highlights.
Programmer and internal documentation:
libjpeg.txt
How to use the JPEG library in your own programs.
example.c
Sample code for calling the JPEG library.
This package contains C software to implement JPEG image encoding, decoding, and
transcoding. JPEG (pronounced “jay-peg”) is a standardized compression method for
full-color and gray-scale images.
This software implements JPEG baseline, extended-sequential, and progressive
compression processes. Provision is made for supporting all variants of these processes,
although some uncommon parameter settings aren’t implemented yet. We have made
no provision for supporting the hierarchical or lossless processes defined in the
standard.
We provide a set of library routines for reading and writing JPEG image files, plus two
sample applications “cjpeg” and “djpeg”, which use the library to perform conversion
between JPEG and some other popular image file formats. The library is intended to be
reused in other applications.
In order to support file conversion and viewing software, we have included
considerable functionality beyond the bare JPEG coding/decoding capability; for
example, the color quantization modules are not strictly part of JPEG decoding, but
they are essential for output to colormapped file formats or colormapped displays.
These extra functions can be compiled out of the library if not required for a particular
application.
We have also included “jpegtran”, a utility for lossless transcoding between different
JPEG processes, and “rdjpgcom” and “wrjpgcom”, two simple applications for
inserting and extracting textual comments in JFIF files.
The emphasis in designing this software has been on achieving portability and
flexibility, while also making it fast enough to be useful. In particular, the software is
not intended to be read as a tutorial on JPEG. (See the REFERENCES section for
introductory material.) Rather, it is intended to be reliable, portable, industrial-strength
code. We do not claim to have achieved that goal in every aspect of the software, but
we strive for it.
We welcome the use of this software as a component of commercial products. No
royalty is required, but we do ask for an acknowledgement in product documentation,
as described under LEGAL ISSUES.
LEGAL ISSUES
In plain English:
1. We don’t promise that this software works. (But if you find any bugs, please let us
know!)
2. You can use this software for whatever you want. You don’t have to pay us.
3. You may not pretend that you wrote this software. If you use it in a program, you
must acknowledge somewhere in your documentation that you’ve used the IJG code.
In legalese:
The authors make NO WARRANTY or representation, either express or implied, with
respect to this software, its quality, accuracy, merchantability, or fitness for a particular
purpose. This software is provided “AS IS”, and you, its user, assume the entire risk as
to its quality and accuracy.
This software is copyright (C) 1991-2009, Thomas G. Lane, Guido Vollbeding.
All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this software (or
portions thereof) for any purpose, without fee, subject to these conditions:
(1) If any part of the source code for this software is distributed, then this README file
must be included, with this copyright and no-warranty notice unaltered; and any
additions, deletions, or changes to the original files must be clearly indicated in
accompanying documentation.
(2) If only executable code is distributed, then the accompanying documentation must
state that “this software is based in part on the work of the Independent JPEG Group”.
(3) Permission for use of this software is granted only if the user accepts full
responsibility for any undesirable consequences; the authors accept NO LIABILITY for
damages of any kind.
These conditions apply to any software derived from or based on the IJG code, not just
to the unmodified library. If you use our work, you ought to acknowledge us.
Permission is NOT granted for the use of any IJG author’s name or company name in
advertising or publicity relating to this software or products derived from it. This
software may be referred to only as “the Independent JPEG Group’s software”.
We specifically permit and encourage the use of this software as the basis of
commercial products, provided that all warranty or liability claims are assumed by the
product vendor.
ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole
proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is
NOT covered by the above copyright and conditions, but instead by the usual
distribution terms of the Free Software Foundation; principally, that you must include
source code if you redistribute it. (See the file ansi2knr.c for full details.) However,
since ansi2knr.c is not needed as part of any program generated from the IJG code, this
does not limit you more than the foregoing paragraphs do.
The Unix configuration script “configure” was produced with GNU Autoconf. It is
copyright by the Free Software Foundation but is freely distributable. The same holds
for its supporting scripts (config.guess, config.sub, ltmain.sh). Another support script,
install-sh, is copyright by X Consortium but is also freely distributable.
The IJG distribution formerly included code to read and write GIF files. To avoid
entanglement with the Unisys LZW patent, GIF reading support has been removed
altogether, and the GIF writer has been simplified to produce “uncompressed GIFs”.
This technique does not use the LZW algorithm; the resulting GIF files are larger than
usual, but are readable by all standard GIF decoders.
We are required to state that
structure.txt
Overview of the JPEG library’s internal structure.
filelist.txt
Road map of IJG files.
“The Graphics Interchange Format(c) is the Copyright property of
coderules.txt
Coding style rules --- please read if you contribute code.
CompuServe Incorporated. GIF(sm) is a Service Mark property of
Please read at least the files install.txt and usage.txt. Some information can also be
found in the JPEG FAQ (Frequently Asked Questions) article. See ARCHIVE
LOCATIONS below to find out where to obtain the FAQ article.
If you want to understand how the JPEG code works, we suggest reading one or more
of the REFERENCES, then looking at the documentation files (in roughly the order
listed) before diving into the code.
OVERVIEW
CompuServe Incorporated.”
REFERENCES
We recommend reading one or more of these references before trying to understand the
innards of the JPEG software.
The best short technical introduction to the JPEG compression algorithm is
Wallace, Gregory K. “The JPEG Still Picture Compression Standard”,
vi
Communications of the ACM, April 1991 (vol. 34 no. 4), pp. 30-44.
(Adjacent articles in that issue discuss MPEG motion picture compression, applications
of JPEG, and related topics.) If you don’t have the CACM issue handy, a PostScript file
containing a revised version of Wallace’s article is available at http://www.ijg.org/files/
wallace.ps.gz. The file (actually a preprint for an article that appeared in IEEE Trans.
Consumer Electronics) omits the sample images that appeared in CACM, but it
includes corrections and some added material. Note: the Wallace article is copyright
ACM and IEEE, and it may not be used for commercial purposes.
A somewhat less technical, more leisurely introduction to JPEG can be found in “The
Data Compression Book” by Mark Nelson and Jean-loup Gailly, published by M&T
Books (New York), 2nd ed. 1996, ISBN 1-55851-434-1. This book provides good
explanations and example C code for a multitude of compression methods including
JPEG. It is an excellent source if you are comfortable reading C code but don’t know
much about data compression in general. The book’s JPEG sample code is far from
industrial-strength, but when you are ready to look at a full implementation, you’ve got
one here...
The best currently available description of JPEG is the textbook “JPEG Still Image
Data Compression Standard” by William B. Pennebaker and Joan L. Mitchell,
published by Van Nostrand Reinhold, 1993, ISBN 0-442-01272-1. Price US$59.95,
638 pp. The book includes the complete text of the ISO JPEG standards (DIS 10918-1
and draft DIS 10918-2).
Although this is by far the most detailed and comprehensive exposition of JPEG
publicly available, we point out that it is still missing an explanation of the most
essential properties and algorithms of the underlying DCT technology.
If you think that you know about DCT-based JPEG after reading this book, then you are
in delusion. The real fundamentals and corresponding potential of DCT-based JPEG are
not publicly known so far, and that is the reason for all the mistaken developments
taking place in the image coding domain.
The original JPEG standard is divided into two parts, Part 1 being the actual
specification, while Part 2 covers compliance testing methods. Part 1 is titled “Digital
Compression and Coding of Continuous-tone Still Images, Part 1: Requirements and
guidelines” and has document numbers ISO/IEC IS 10918-1, ITU-T T.81. Part 2 is
titled “Digital Compression and Coding of Continuous-tone Still Images, Part 2:
Compliance testing” and has document numbers ISO/IEC IS 10918-2, ITU-T T.83.
The JPEG standard does not specify all details of an interchangeable file format. For the
omitted details we follow the “JFIF” conventions, revision 1.02. A copy of the JFIF
spec is available from:
Literature Department
C-Cube Microsystems, Inc.
1778 McCarthy Blvd.
Milpitas, CA 95035
phone (408) 944-6300, fax (408) 944-6314
A PostScript version of this document is available at http://www.ijg.org/files/jfif.ps.gz.
There is also a plain text version at http://www.ijg.org/files/jfif.txt.gz, but it is missing
the figures.
The TIFF 6.0 file format specification can be obtained by FTP from ftp://ftp.sgi.com/
graphics/tiff/TIFF6.ps.gz. The JPEG incorporation scheme found in the TIFF 6.0 spec
of 3-June-92 has a number of serious problems. IJG does not recommend use of the
TIFF 6.0 design (TIFF Compression tag 6). Instead, we recommend the JPEG design
proposed by TIFF Technical Note #2 (Compression tag 7). Copies of this Note can be
obtained from http://www.ijg.org/files/. It is expected that the next revision of the TIFF
spec will replace the 6.0 JPEG design with the Note’s design. Although IJG’s own code
does not support TIFF/JPEG, the free libtiff library uses our library to implement TIFF/
JPEG per the Note.
ARCHIVE LOCATIONS
The “official” archive site for this software is www.ijg.org. The most recent released
version can always be found there in directory “files”. This particular version will be
archived as http://www.ijg.org/files/jpegsrc.v7.tar.gz, and in Windows-compatible
“zip” archive format as http://www.ijg.org/files/jpegsr7.zip.
The JPEG FAQ (Frequently Asked Questions) article is a source of some general
information about JPEG. It is available on the World Wide Web at http://www.faqs.org/
faqs/jpeg-faq/ and other news.answers archive sites, including the official
news.answers archive at rtfm.mit.edu: ftp://rtfm.mit.edu/pub/usenet/news.answers/
jpeg-faq/. If you don’t have Web or FTP access, send e-mail to mailserver@rtfm.mit.edu with body
send usenet/news.answers/jpeg-faq/part1
send usenet/news.answers/jpeg-faq/part2
ACKNOWLEDGMENTS
Thank to Juergen Bruder of the Georg-Cantor-Organization at the Martin-LutherUniversity Halle for providing me with a copy of the common DCT algorithm article,
only to find out that I had come to the same result in a more direct and comprehensible
way with a more generative approach.
Thank to Istvan Sebestyen and Joan L. Mitchell for inviting me to the ITU JPEG (Study
Group 16) meeting in Geneva, Switzerland.
Thank to Thomas Wiegand and Gary Sullivan for inviting me to the Joint Video Team
(MPEG & ITU) meeting in Geneva, Switzerland.
Thank to John Korejwa and Massimo Ballerini for inviting me to fruitful consultations
in Boston, MA and Milan, Italy.
Thank to Hendrik Elstner, Roland Fassauer, and Simone Zuck for corresponding
business development.
Thank to Nico Zschach and Dirk Stelling of the technical support team at the Digital
Images company in Halle for providing me with extra equipment for configuration
tests.
Thank to Richard F. Lyon (then of Foveon Inc.) for fruitful communication about JPEG
configuration in Sigma Photo Pro software.
Last but not least special thank to Thomas G. Lane for the original design and
development of this singular software package.
vii
FILE FORMAT WARS
The ISO JPEG standards committee actually promotes different formats like JPEG2000 or JPEG-XR which are incompatible with original DCT-based JPEG and which
are based on faulty technologies. IJG therefore does not and will not support such
momentary mistakes (see REFERENCES). We have little or no sympathy for the
promotion of these formats. Indeed, one of the original reasons for developing this free
software was to help force convergence on common, interoperable format standards for
JPEG files. Don’t use an incompatible file format! (In any case, our decoder will remain
capable of reading existing JPEG image files indefinitely.)
TO DO
v7 is basically just a necessary interim release, paving the way for a major breakthrough
in image coding technology with the next v8 package which is scheduled for release in
the year 2010.
Please send bug reports, offers of help, etc. to jpeg-info@jpegclub.org.
■ About International Components for Unicode
ICU License - ICU 1.8.1 and later
COPYRIGHT AND PERMISSION NOTICE
Copyright (C) 1995-2003 International Business Machines Corporation and others
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the “Software”), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge,
publish, distribute, and/or sell copies of the Software, and to permit persons to whom
the Software is furnished to do so, provided that the above copyright notice(s) and this
permission notice appear in all copies of the Software and that both the above copyright
notice(s) and this permission notice appear in supporting documentation.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO
EVENT SHALL THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS
NOTICE BE LIABLE FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR
CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
OF THIS SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in
advertising or otherwise to promote the sale, use or other dealings in this Software
without prior written authorization of the copyright holder.
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
■ About libpng
This copy of the libpng notices is provided for your convenience. In case of any
discrepancy between this copy and the notices in the file png.h that is included in the
libpng distribution, the latter shall prevail.
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modify libpng you may insert additional notices immediately following this
sentence. This code is released under the libpng license.
libpng versions 1.2.6, August 15, 2004, through 1.2.45, July 7, 2011, are Copyright (C)
2004, 2006-2009 Glenn Randers-Pehrson, and are distributed according to the same
disclaimer and license as libpng-1.2.5 with the following individual added to the list of
Contributing Authors
Cosmin Truta
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright
(C) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same
disclaimer and license as libpng-1.0.6 with the following individuals added to the
list of Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant
and with the following additions to the disclaimer:
There is no warranty against interference with your enjoyment of the library or
against infringement. There is no warranty that our efforts or the library will fulfill
any of your particular purposes or needs. This library is provided with all faults,
and the entire risk of satisfactory quality, performance, accuracy, and effort is with
the user.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (C)
1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same
disclaimer and license as libpng-0.96, with the following individuals added to the list of
Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (C) 1996, 1997
Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88,
with the following individuals added to the list of Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
Magnus Holmgren
Greg Roelofs
Tom Tanner
libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (C) 1995,
1996 Guy Eric Schalnat, Group 42, Inc.
For the purposes of this copyright and license, “Contributing Authors” is defined as the
following set of individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
Paul Schmidt
Tim Wegner
The PNG Reference Library is supplied “AS IS”. The Contributing Authors and Group
42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the
warranties of merchantability and of fitness for any purpose. The Contributing Authors
and Group 42, Inc. assume no liability for direct, indirect, incidental, special,
exemplary, or consequential damages, which may result from the use of the PNG
Reference Library, even if advised of the possibility of such damage.
Permission is hereby granted to use, copy, modify, and distribute this source code, or
portions hereof, for any purpose, without fee, subject to the following restrictions:
1. The origin of this source code must not be misrepresented.
2. Altered versions must be plainly marked as such and must not be misrepresented
as being the original source.
3. This Copyright notice may not be removed or altered from any source or altered
source distribution.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and
encourage the use of this source code as a component to supporting the PNG file format
in commercial products. If you use this source code in a product, acknowledgment is
not required but would be appreciated.
A “png_get_copyright” function is available, for convenient use in “about” boxes and
the like:
printf(“%s”,png_get_copyright(NULL));
Also, the PNG logo (in PNG format, of course) is supplied in the files “pngbar.png” and
“pngbar.jpg (88x31) and “pngnow.png” (98x31).
Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a
certification mark of the Open Source Initiative.
Glenn Randers-Pehrson
glennrp at users.sourceforge.net
July 7, 2011
■ About tinyxml
www.sourceforge.net/projects/tinyxml
Original code (2.0 and earlier )copyright (C) 2000-2006 Lee Thomason
(www.grinninglizard.com)
This software is provided ‘as-is’, without any express or implied warranty. In no event
will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including
commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you
wrote the original software. If you use this software in a product, an acknowledgment in
the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
■ About dtoa and strtod
The author of this software is David M. Gay.
Copyright (C) 1991, 2000, 2001 by Lucent Technologies.
Permission to use, copy, modify, and distribute this software for any purpose without
fee is hereby granted, provided that this entire notice is included in all copies of any
software which is or includes a copy or modification of this software and in all copies
of the supporting documentation for such software.
THIS SOFTWARE IS BEING PROVIDED “AS IS”, WITHOUT ANY EXPRESS OR
IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR
LUCENT MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND
CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS
FITNESS FOR ANY PARTICULAR PURPOSE.
■ About gSOAP
gSOAP Public License
Version 1.3b
The gSOAP public license is derived from the Mozilla Public License (MPL1.1). The
sections that were deleted
from the original MPL1.1 text are 1.0.1, 2.1.(c),(d), 2.2.(c),(d), 8.2.(b), 10, and 11.
Section 3.8 was added. The
modified sections are 2.1.(b), 2.2.(b), 3.2 (simplified), 3.5 (deleted the last sentence),
and 3.6 (simplified).
This license applies to the gSOAP software package, with the exception of the wsdl2h
source code located in
gsoap/wsdl, all code generated by wsdl2h, the UDDI source code gsoap/uddi2, and the
Web server sample
source code samples/webserver. To use all of the software commercially, a commercial
license has to be obtained
from www.genivia.com.
1 DEFINITIONS.
1.0.1.
1.1. “Contributor” means each entity that creates or contributes to the creation of
Modifications.
1.2. “Contributor Version” means the combination of the Original Code, prior
Modifications used by a Contributor, and the Modifications made by that particular
Contributor.
1.3. “Covered Code” means the Original Code, or Modifications or the combination of
the Original Code, and Modifications, in each case including portions thereof.
1.4. “Electronic Distribution Mechanism” means a mechanism generally accepted in
the software development community for the electronic transfer of data.
1.5. “Executable” means Covered Code in any form other than Source Code.
1.6. “Initial Developer” means the individual or entity identified as the Initial
Developer in the Source Code notice required by Exhibit A.
1.7. “Larger Work” means a work which combines Covered Code or portions thereof
with code not governed by the terms of this License.
1.8. “License” means this document.
1.8.1. “Licensable” means having the right to grant, to the maximum extent possible,
whether at the time of the initial grant or subsequently acquired, any and all of the rights
conveyed herein.
1.9. “Modifications” means any addition to or deletion from the substance or structure
of either the Original Code or any previous Modifications. When Covered Code is
released as a series of files, a Modification is: A.
Any addition to or deletion from the contents of a file containing Original Code or
previous Modifications. B.
Any new file that contains any part of the Original Code, or previous Modifications.
1.10. “Original Code” means Source Code of computer software code which is
described in the Source Code notice required by Exhibit A as Original Code, and which,
at the time of its release under this License is not already Covered Code governed by
this License.
1.10.1. “Patent Claims” means any patent claim(s), now owned or hereafter acquired,
including without limitation, method, process, and apparatus claims, in any patent
Licensable by grantor.
http://www.cs.fsu.edu/~engelen/license.html
1.11. “Source Code” means the preferred form of the Covered Code for making
modifications to it, including all modules it contains, plus any associated interface
definition files, scripts used to control compilation and installation of an Executable, or
source code differential comparisons against either the Original Code or another well
known, available Covered Code of the Contributor’s choice. The Source Code can be in
a compressed or archival form, provided the appropriate decompression or de-archiving
software is widely available for no charge.
1.12. “You” (or “Your”) means an individual or a legal entity exercising rights under,
and complying with all of the terms of, this License or a future version of this License
issued under Section 6.1. For legal entities, “You” includes any entity which controls, is
controlled by, or is under common control with You. For purposes of this definition,
“control” means (a) the power, direct or indirect, to cause the direction or management
of such entity, whether by contract or otherwise, or (b) ownership of more than fifty
percent (50%) of the outstanding shares or beneficial ownership of such entity.
2 SOURCE CODE LICENSE.
2.1. The Initial Developer Grant. The Initial Developer hereby grants You a worldwide, royalty-free, non-exclusive license, subject to third party intellectual property
claims:
(a)
under intellectual property rights (other than patent or trademark) Licensable by Initial
Developer to use, reproduce, modify, display, perform, sublicense and distribute the
Original Code (or portions thereof) with or without Modifications, and/or as part of a
Larger Work; and
(b)
under patents now or hereafter owned or controlled by Initial Developer, to make, have
made, use and sell (“offer to sell and import”) the Original Code, Modifications, or
portions thereof, but solely to the extent that any such patent is reasonably necessary to
enable You to utilize, alone or in combination with other software, the Original Code,
Modifications, or any combination or portions thereof.
(c)
(d)
2.2. Contributor Grant.
Subject to third party intellectual property claims, each Contributor hereby grants You a
world-wide, royalty-free, non-exclusive license
(a)
under intellectual property rights (other than patent or trademark) Licensable by
Contributor, to use, reproduce, modify, display, perform, sublicense and distribute the
Modifications created by such Contributor (or portions thereof) either on an unmodified
basis, with other Modifications, as Covered Code and/or as part of a Larger Work; and
(b)
under patents now or hereafter owned or controlled by Contributor, to make, have
made, use and sell (“offer to sell and import”) the Contributor Version (or portions
thereof), but solely to the extent that any such patent is reasonably necessary to enable
You to utilize, alone or in combination with other software, the Contributor Version (or
portions thereof).
(c)
(d)
3 DISTRIBUTION OBLIGATIONS.
3.1. Application of License.
The Modifications which You create or to which You contribute are governed by the
terms of this License, including without limitation Section 2.2. The Source Code
version of Covered Code may be distributed only under the terms of this License or a
future version of this License released under Section 6.1, and You must include a copy
of this License with every copy of the Source Code You distribute. You may not offer
or impose any terms on any Source Code version that alters or restricts the applicable
version of this License or the recipients’ rights hereunder. However, You may include
an additional document offering the additional rights described in Section 3.5.
3.2. Availability of Source Code.
viii
Any Modification created by You will be provided to the Initial Developer in Source
Code form and are subject to the terms of the License.
3.3. Description of Modifications.
You must cause all Covered Code to which You contribute to contain a file
documenting the changes You made to create that Covered Code and the date of any
change. You must include a prominent statement that the Modification is derived,
directly or indirectly, from Original Code provided by the Initial Developer and
including the name of the Initial Developer in (a) the Source Code, and (b) in any notice
in an Executable version or related documentation in which You describe the origin or
ownership of the Covered Code.
3.4. Intellectual Property Matters.
(a) Third Party Claims.
If Contributor has knowledge that a license under a third party’s intellectual property
rights is required to exercise the rights granted by such Contributor under Sections 2.1
or 2.2, Contributor must include a text file with the Source Code distribution titled
“LEGAL” which describes the claim and the party making the claim in sufficient detail
that a recipient will know whom to contact. If Contributor obtains such knowledge after
the Modification is made available as described in Section 3.2, Contributor shall
promptly modify the LEGAL file in all copies Contributor makes available thereafter
and shall take other steps (such as notifying appropriate mailing lists or newsgroups)
reasonably calculated to inform those who received the Covered Code that new
knowledge has been obtained.
(b) Contributor APIs.
If Contributor’s Modifications include an application programming interface and
Contributor has knowledge of patent licenses which are reasonably necessary to
implement that API, Contributor must also include this information in the LEGAL file.
(c) Representations.
Contributor represents that, except as disclosed pursuant to Section 3.4(a) above,
Contributor believes that Contributor’s Modifications are Contributor’s original
creation(s) and/or Contributor has sufficient rights to grant the rights conveyed by this
License.
3.5. Required Notices.
You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not
possible to put such notice in a particular Source Code file due to its structure, then You
must include such notice in a location (such as a relevant directory) where a user would
be likely to look for such a notice. If You created one or more Modification(s) You may
add your name as a Contributor to the notice described in Exhibit A. You must also
duplicate this License in any documentation for the Source Code where You describe
recipients’ rights or ownership rights relating to Covered Code. You may choose to
offer, and to charge a fee for, warranty, support, indemnity or liability obligations to
one or more recipients of Covered Code. However, You may do so only on Your own
behalf, and not on behalf of the Initial Developer or any Contributor.
3.6. Distribution of Executable Versions.
You may distribute Covered Code in Executable form only if the requirements of
Section 3.1-3.5 have been met for that Covered Code. You may distribute the
Executable version of Covered Code or ownership rights under a license of Your
choice, which may contain terms different from this License, provided that You are in
compliance with the terms of this License and that the license for the Executable
version does not attempt to limit or alter the recipient’s rights in the Source Code
version from the rights set forth in this License. If You distribute the Executable version
under a different license You must make it absolutely clear that any terms which differ
from this License are offered by You alone, not by the Initial Developer or any
Contributor. If you distribute executable versions containing Covered Code as part of a
product, you must reproduce the notice in Exhibit B in the documentation and/or other
materials provided with the product.
3.7. Larger Works.
You may create a Larger Work by combining Covered Code with other code not
governed by the terms of this License and distribute the Larger Work as a single
product. In such a case, You must make sure the requirements of this License are
fulfilled for the Covered Code.
3.8. Restrictions.
You may not remove any product identification, copyright, proprietary notices or labels
from gSOAP.
4 INABILITY TO COMPLY DUE TO STATUTE OR REGULATION.
If it is impossible for You to comply with any of the terms of this License with respect
to some or all of the Covered Code due to statute, judicial order, or regulation then You
must: (a) comply with the terms of this License to the maximum extent possible; and
(b) describe the limitations and the code they affect. Such description must be included
in the LEGAL file described in Section 3.4 and must be included with all distributions
of the Source Code. Except to the extent prohibited by statute or regulation, such
description must be sufficiently detailed for a recipient of ordinary skill to be able to
understand it.
5 APPLICATION OF THIS LICENSE.
This License applies to code to which the Initial Developer has attached the notice in
Exhibit A and to related Covered Code.
6 VERSIONS OF THE LICENSE.
6.1. New Versions.
Grantor may publish revised and/or new versions of the License from time to time.
Each version will be given a distinguishing version number.
6.2. Effect of New Versions.
Once Covered Code has been published under a particular version of the License, You
may always continue to use it under the terms of that version. You may also choose to
use such Covered Code under the terms of any subsequent version of the License.
6.3. Derivative Works.
If You create or use a modified version of this License (which you may only do in order
to apply it to code which is not already Covered Code governed by this License), You
must (a) rename Your license so that the phrase “gSOAP” or any confusingly similar
phrase do not appear in your license (except to note that your license differs from this
License) and (b) otherwise make it clear that Your version of the license contains terms
which differ from the gSOAP Public License. (Filling in the name of the Initial
Developer, Original Code or Contributor in the notice described in Exhibit A shall not
of themselves be deemed to be modifications of this License.)
ix
7 DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN “AS IS” BASIS,
WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED OR
STATUTORY, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, OF FITNESS FOR A PARTICULAR
PURPOSE, NONINFRINGEMENT OF THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS, AND ANY WARRANTY THAT MAY ARISE BY REASON
OF TRADE USAGE, CUSTOM, OR COURSE OF DEALING. WITHOUT
LIMITING THE FOREGOING, YOU ACKNOWLEDGE THAT THE SOFTWARE
IS PROVIDED “AS IS” AND THAT THE AUTHORS DO NOT WARRANT THE
SOFTWARE WILL RUN UNINTERRUPTED OR ERROR FREE. LIMITED
LIABILITY THE ENTIRE RISK AS TO RESULTS AND PERFORMANCE OF THE
SOFTWARE IS ASSUMED BY YOU. UNDER NO CIRCUMSTANCES WILL THE
AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,
EXEMPLARY OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE
WHATSOEVER, WHETHER BASED ON CONTRACT, WARRANTY, TORT
(INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, ARISING
OUT OF OR IN ANY WAY RELATED TO THE SOFTWARE, EVEN IF THE
AUTHORS HAVE BEEN ADVISED ON THE POSSIBILITY OF SUCH DAMAGE
OR IF SUCH DAMAGE COULD HAVE BEEN REASONABLY FORESEEN, AND
NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY
EXCLUSIVE REMEDY PROVIDED. SUCH LIMITATION ON DAMAGES
INCLUDES, BUT IS NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL,
LOST PROFITS, LOSS OF DATA OR SOFTWARE, WORK STOPPAGE,
COMPUTER FAILURE OR MALFUNCTION OR IMPAIRMENT OF OTHER
GOODS. IN NO EVENT WILL THE AUTHORS BE LIABLE FOR THE COSTS OF
PROCUREMENT OF SUBSTITUTE SOFTWARE OR SERVICES. YOU
ACKNOWLEDGE THAT THIS SOFTWARE IS NOT DESIGNED FOR USE IN ONLINE EQUIPMENT IN HAZARDOUS ENVIRONMENTS SUCH AS OPERATION
OF NUCLEAR FACILITIES, AIRCRAFT NAVIGATION OR CONTROL, OR LIFECRITICAL APPLICATIONS. THE AUTHORS EXPRESSLY DISCLAIM ANY
LIABILITY RESULTING FROM USE OF THE SOFTWARE IN ANY SUCH ONLINE EQUIPMENT IN HAZARDOUS ENVIRONMENTS AND ACCEPTS NO
LIABILITY IN RESPECT OF ANY ACTIONS OR CLAIMS BASED ON THE USE
OF THE SOFTWARE IN ANY SUCH ON-LINE EQUIPMENT IN HAZARDOUS
ENVIRONMENTS BY YOU. FOR PURPOSES OF THIS PARAGRAPH, THE
TERM “LIFE- CRITICAL APPLICATION” MEANS AN APPLICATION IN
WHICH THE FUNCTIONING OR MALFUNCTIONING OF THE SOFTWARE
MAY RESULT DIRECTLY OR INDIRECTLY IN PHYSICAL INJURY OR LOSS
OF HUMAN LIFE. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN
ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS
AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
8 TERMINATION.
8.1.
This License and the rights granted hereunder will terminate automatically if You fail to
comply with terms herein and fail to cure such breach within 30 days of becoming
aware of the breach. All sublicenses to the Covered Code which are properly granted
shall survive any termination of this License. Provisions which, by their nature, must
remain in effect beyond the termination of this License shall survive.
8.2.
8.3.
If You assert a patent infringement claim against Participant alleging that such
Participant’s Contributor Version directly or indirectly infringes any patent where such
claim is resolved (such as by license or settlement) prior to the initiation of patent
infringement litigation, then the reasonable value of the licenses granted by such
Participant under Sections 2.1 or 2.2 shall be taken into account in determining the
amount or value of any payment or license.
8.4.
In the event of termination under Sections 8.1 or 8.2 above, all end user license
agreements (excluding distributors and resellers) which have been validly granted by
You or any distributor hereunder prior to termination shall survive termination.
9 LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER
TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL
YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY
DISTRIBUTOR OF COVERED CODE, OR ANY SUPPLIER OF ANY OF SUCH
PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER
INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL,
WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND
ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY
SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.
THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR
DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY’S
NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH
LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS
EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU.
10 U.S. GOVERNMENT END USERS.
11 MISCELLANEOUS.
12 RESPONSIBILITY FOR CLAIMS.
As between Initial Developer and the Contributors, each party is responsible for claims
and damages arising, directly or indirectly, out of its utilization of rights under this
License and You agree to work with Initial Developer and Contributors to distribute
such responsibility on an equitable basis. Nothing herein is intended or shall be deemed
to constitute any admission of liability.
EXHIBIT A.
“The contents of this file are subject to the gSOAP Public License Version 1.3 (the
“License”); you may not use this
file except in compliance with the License. You may obtain a copy of the License
athttp://www.cs.fsu.edu/ engelen/soaplicense.html
Software distributed under the License is distributed on an “AS IS” basis, WITHOUT
WARRANTY OF ANY KIND, either express or implied. See the License for the
specific language governing rights and limitations under the License.
The Original Code of the gSOAP Software is: stdsoap.h, stdsoap2.h, stdsoap.c,
stdsoap2.c, stdsoap.cpp,
stdsoap2.cpp, soapcpp2.h, soapcpp2.c, soapcpp2_lex.l, soapcpp2_yacc.y, error2.h,
error2.c, symbol2.c, init2.c,
soapdoc2.html, and soapdoc2.pdf, httpget.h, httpget.c, stl.h, stldeque.h, stllist.h,
stlvector.h, stlset.h.
The Initial Developer of the Original Code is Robert A. van Engelen. Portions created
by Robert A. van Engelen are
Copyright (C) 2001-2004 Robert A. van Engelen, Genivia inc. All Rights Reserved.
Contributor(s):
“________________________.”
[Note: The text of this Exhibit A may differ slightly form the text of the notices in the
Source Code files of the Original code. You should use the text of this Exhibit A rather
than the text found in the Original Code Source Codefor Your Modifications.]
EXHIBIT B.
“Part of the software embedded in this product is gSOAP software.
Portions created by gSOAP are Copyright (C) 2001-2009 Robert A. van Engelen, Genivia
inc. All Rights Reserved. THE SOFTWARE IN THIS PRODUCT WAS IN PART
PROVIDED BY GENIVIA INC AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.”
http://www.cs.fsu.edu/~engelen/license.html
■ About fonts
Fonts are (c) Bitstream (see below). DejaVu changes are in public domain.
Glyphs imported from Arev fonts are (c) Tavmjong Bah (see below)
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts
accompanying this license (“Fonts”) and associated documentation files (the “Font
Software”), to reproduce and distribute the modifications to the Bitstream Vera Font
Software, including without limitation the rights to use, copy, merge, publish,
distribute, and/or sell copies of the Font Software, and to permit persons to whom the
Font Software is furnished to do so, subject to the following conditions:
The above copyright and trademark notices and this permission notice shall be included
in all copies of one or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs
of glyphs or characters in the Fonts may be modified and additional glyphs or
characters may be added to the Fonts, only if the fonts are renamed to names not
containing either the words “Tavmjong Bah” or the word “Arev”.
This License becomes null and void to the extent applicable to Fonts or Font Software
that has been modified and is distributed under the “Tavmjong Bah Arev” names.
The Font Software may be sold as part of a larger software package but no copy of one
or more of the Font Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT,
TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL TAVMJONG BAH BE
LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING
ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE
FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.
Except as contained in this notice, the name of Tavmjong Bah shall not be used in
advertising or otherwise to promote the sale, use or other dealings in this Font Software
without prior written authorization from Tavmjong Bah. For further information,
contact: tavmjong @ free. fr.
Bitstream Vera Fonts Copyright
-----------------------------Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a
trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts
accompanying this license (“Fonts”) and associated documentation files (the “Font Software”),
to reproduce and distribute the Font Software, including without limitation the rights to use,
copy, merge, publish, distribute, and/or sell copies of the Font Software, and to permit persons
to whom the Font Software is furnished to do so, subject to the following conditions:
The above copyright and trademark notices and this permission notice shall be included
in all copies of one or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs
of glyphs or characters in the Fonts may be modified and additional glyphs or
characters may be added to the Fonts, only if the fonts are renamed to names not
containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software
that has been modified and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one
or more of the Font Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT,
TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE
GNOME FOUNDATION BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO
USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT
SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and
Bitstream Inc., shall not be used in advertising or otherwise to promote the sale, use or
other dealings in this Font Software without prior written authorization from the Gnome
Foundation or Bitstream Inc., respectively. For further information, contact: fonts at
gnome dot org.
Arev Fonts Copyright
-----------------------------Copyright (c) 2006 by Tavmjong Bah. All Rights Reserved.
x
r
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
The laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
LASER Specification:
Class 1 LASER Product
Wave length: 790 nm (CDs)/658 nm (DVDs)/405 nm (BDs)
Laser output: max. 1 mW
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K. Model
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN.
DO NOT STARE INTO BEAM.
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
DANGER: INVISIBLE LASER RADIATION WHEN OPEN.
AVOID DIRECT EXPOSURE TO THE BEAM.
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L
or coloured RED.
Make sure that neither core is connected to the earth
terminal of the three pin plug.
© 2011 Yamaha Corporation
Printed in China MCR-750_AB-1
Download PDF

advertising