Dishwasher - Summit Appliance
Dishwasher
Installation Manual
FOR MODELS
DW2432
DW2432SS
DW2433SS
USA
Installation Manual For
Dishwasher Models
DW2432
DW2432SS
DW2433SS
To prevent accidents, which could cause serious injury or death, as well as
machine damage read these instructions before installation and / or use.
Contents
1. IMPORTANT SAFETY INSTRUCTIONS
1
2. TOOLS WHICH MAY BE NEEDED
3
3. MATERIALS WHICH MAY BE NEEDED
3
4. MATERIALS SUPPLIED
4
5. DISHWASHER SPECIFICATIONS
5
6. ENCLOSURE PREPARATION
6
1.1 INSPECT THE DISHWASHER
1.2 HOW TO CONTACT US :
4.1 PARTS SUPPLIED
4.2 MANUAL BAG
4.3 DISHWASHER PARTS BAG 1
4.4 PARTS ATTACHED TO THE REAR OF THE DISHWASHER
5.1 TECHNICAL FEATURES
2
2
4
4
4
4
5
6.1 ELECTRICAL PREPARATION
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS
6.3 ADJUSTING HEIGHT
6.4 INSTALLING THE SIDE TRIM STRIPS
6.5 PREPARING THE WATER CONNECTION (A)
6.6 DRAIN PREPARATION
6.7 STEAM PROTECTION FOIL
6
7
7
9
10
11
12
7. PLACEMENT OF DISHWASHER INTO THE OPENING
13
8. INSTALLER CHECKLIST
18
9. FINAL INSTRUCTIONS
18
10. SELF HELP HINTS:
18
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS
7.2 ELECTRICAL CONNECTION
7.3 READJUSTING FOOT LEVELS
7.4 ADJUSTING THE MOVABLE TOE KICK
13
14
16
16
INTRODUCTION
WARNING
Please read this installation manual
and particularly the safety instructions
completely and carefully. They will save you
time and effort and help to ensure optimum
dishwasher performance.
When installing the dishwasher, follow
basic precautions, including the
following:
• The dishwasher installation must be
performed in accordance with this
installation manual. If you did not receive
an installation manual, order it by
calling 1-800-287-8799 or you may also
download it from our web site at
www.summitappliances.com
• Installation and repair should be
performed by a qualified installer.
Work by unqualified persons could be
dangerous and may void the warranty.
Be sure to observe all listed warnings and
cautions. Look particularly for the icons with
exclamation marks inside. The information
icon also will provide important references.
Notice :
WARNING:
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION:
Indicates a potentially hazardous situation
which, if not avoided, may result in injury.
It may also be used to alert against unsafe
practices.
Notice:
Indicates a potentially hazardous situation
which, if not avoided, may result in damage
to the dishwasher, the table-ware, the
equipment or the environment.
Installation should be installed by an
insured licensed plumber, contractor or
trained installer. Installation performed
by persons other than this could result in
improper installation and property damage.
• Do not operate the appliance if damaged,
malfunctioning, partially disassembled or
if it has missing or broken parts.
• Also follow the safety instructions of the
user manual.
• To reduce the risk of electric shock, fire,
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.
• Only connect the dishwasher to the
power supply when all installation and
plumbing work is complete.
• If the dishwasher is installed in a location
that experiences freezing temperatures
(e.g. in a vacation home, cabin, etc.),
you must drain all the water from the
dishwasher’s interior. Water system
ruptures that occur as a result of freezing
are not covered by warranty.
• Dishwasher must be secured to adjacent
cabinetry using the brackets provided.
Failure to do this may cause damage to
property or bodily injury.
• Connect to a properly rated, protected
and sized power supply circuit to avoid
electrical overload. The dishwasher is
designed for an electrical supply of 120 V
(volts), 60 Hz (hertz), AC, connected to a
1. IMPORTANT SAFETY
INSTRUCTIONS
In addition to these instructions, the
dishwasher shall be installed:
• In accordance with all local codes or, in
absence of a local code,
• In the United States, with the National
Electric Code,
• In Canada, with the Canadian Electric
Code C22.1-latest edition/Provincial and
Municipal codes and/or local codes.
Notice :
Read these installation instructions
completely before installing and follow
them carefully. Save these installation
instructions and pass them on to any future
user.
1
USA
dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breakers
rated for 15 amperes. Electrical supply
conductors shall be a minimum of # 14
AWG copper wire rated at 75 °C (167
°F) or higher. These requirements must
be met to prevent injury and machine
damage. Consult a qualified electrician if
in doubt.
• Do not use any extension cord or
portable outlet device to connect the
dishwasher to a power supply.
• Ensure that any plastic wrappings, bags,
small pieces etc. are disposed of safely
and kept out of the reach of children.
Danger of suffocation!
• Remove the door to the washing
compartment when removing an old
dishwasher from service or discarding it.
Ensure that the appliance presents no
danger to children while being stored for
disposal.
• Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
1.1 INSPECT THE DISHWASHER
After unpacking the dishwasher and prior
to installation, thoroughly inspect the
dishwasher for possible freight or cosmetic
damage. Report any damage immediately.
Notice :
• Cosmetic defects must be reported within
10 days of installation.
• Do not discard any bags or items that
come with the original package until
after the entire installation has been
completed.
1.2 HOW TO CONTACT US :
You may either call our Toll Free Number at
1-800-287-8799 or contact us via the web
site at
www.summitappliances.com
or Contact the Blomberg Distributor for
your State or Province as listed on the
Distributor Contact List provided.
Notice :
• The dishwasher drain hose must be
installed with a drain loop at least 28”
(710mm) off the cabinet floor; otherwise
the dishwasher may not drain properly.
• This dishwasher is intended for
residential use only, and should not be
used in commercial establishments.
• New installation - If the dishwasher is a
new installation, most of the work must
be done before the dishwasher is moved
into place.
• Replacement - If the dishwasher is
replacing another dishwasher, check
the existing dishwasher connections for
compatibility with the new dishwasher,
and replace parts as necessary.
2
USA
2. TOOLS WHICH MAY BE NEEDED
3. MATERIALS WHICH MAY BE NEEDED
(Additional materials may be required to comply with local codes)
Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided
dishwasher supply line.
Electrical Supply Cable - Minimum #14AWG, 2 conductors, 1 ground,
insulated copper conductors.
90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your
water supply line (copper tubing/compression fitting, or braided hose) on
the other leg.
UL listed conduit connector or strain relief.
Teflon tape or other pipe thread compound to seal plumbing connections.
Shut-off valve and fittings appropriate for hot water supply line (copper
tubing/compression fitting, or braided hose).
Silicone
Glue
3
USA
4. MATERIALS SUPPLIED
4.1 PARTS SUPPLIED
Parts for your dishwasher will come in several plastic bags.
Check your parts bags shown to make sure you have all the
parts as listed to the left.
4.2 MANUAL BAG
The dishwasher comes with a manual bag containing:
• User manual,
• Installation manual and
• Quick reference guide.
4.3 DISHWASHER PARTS BAG 1
This dishwasher bag comes with the following parts:
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
c. Adjusting Wrench
d. Screws Ø 1/8” x 5/8” (Ø 3.5mm x 14mm)
e. Mounting Bracket Left
f. Mounting Bracket Right
g. Spring Clamp
h. Screw Clamp
j. Rubber Connector
k. Toe Kick Bracket - Left
l. Toe Kick Bracket - Right
m. Wire Nuts
n. Long Legs
o. Toe Kick (toe kick without slots)
p. Toe Kick
r. Toe Kick
s. Plastic Caps
t. Screws Ø 3/16” x 1/4” (Ø 4mm x 6mm)
u. Steam Protection Foil
4.4 PARTS ATTACHED TO THE REAR OF THE
DISHWASHER
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
o. Toe Kick (toe kick without slots)
p. Toe Kick
r. Toe Kick
4
USA
5. DISHWASHER SPECIFICATIONS
5.1 TECHNICAL FEATURES
Load capacity
14 place settings
Permissible water
pressure
4.35 - 145 psi (0.3 - 10 bars)
Electrical connection
120 V (volts), 12 A (amps),
60 Hz (hertz)
Total power
1200 W (watts)
Heater power
1000 W (watts)
Notice :
Because we continually strive to improve our products, we may change our specifications
and design without prior notice. This device corresponds to the following directives:
UL 749 Household Dishwasher directive.
5
USA
6. ENCLOSURE PREPARATION
Notice :
• For proper dishwasher operation and appearance ensure that the enclosure has the
minimum dimensions shown in the figure above.
6.1 ELECTRICAL PREPARATION
WARNING
To avoid electrical shock and/or a fire hazard, make sure electrical work is properly
installed. Only qualified electricians should perform electrical work.
Before installation disconnect the power supply to the work area by unplugging the
unit, “tripping” the circuit breaker or removing the fuse.
The installer has the responsibility of ensuring that the dishwasher electrical
installation is in compliance with all national and local electrical codes and ordinances.
The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected
to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker
rated for 15 amperes.
WARNING
Electrical supply cords must be a minimum #14AWG
copper wire.
Position the cable extending approximately 30” (760mm)
from the enclosure’s back (Figure A).
To the right side position the cable extending
approximately 5½” (140mm) (Figure B).
Remove 2 15/16” - 315/16” (75mm-100mm)
of the cable’s outer casing, and then
remove 3/8” -1/2” (9-13mm) of insulation
from each wire. (Figure C)
6
USA
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS
WARNING
Dishwasher must be secured to adjacent
cabinetry using the mounting brackets
provided. Failure to do this may cause
damage to property or bodily injury.
Place the two mounting brackets into the
top corners of the dishwasher.
Bend sides of mounting brackets (A) in
order to fix from sides (if necessary).
6.3 ADJUSTING HEIGHT
Measure the height of the enclosure.
7
USA
6.3.1 INSTALLING THE FOOT SUPPORTS
Supplied (4)
If the height of the enclosure is 337/16” to
341/4” (850mm - 870mm) use short supports
as shown in the figure.
If the height of the enclosure is above
341/4” (870mm) use long supports as
shown in the figure.
Supplied (4)
8
USA
Adjust the front foot level with the adjusting
wrench to balance and raise the dishwasher to
the enclosure height.
Adjust the rear foot level with a screwdriver
to balance and raise the dishwasher to the
enclosure height.
Notice :
• Make sure the dishwasher is plumb and
notice dishwasher can be placed with a
small clearance under the counter top.
• Turning the screwdriver in the direction of
the black arrows will bring the dishwasher
back feet up.
• Turning the screwdriver in the direction of
the white arrows will take the dishwasher
rear feet down.
6.4 INSTALLING THE SIDE TRIM
STRIPS
1. Remove the adhesive tape (Figure A).
Place the trim strips on the front edge of the
side walls (Figure B).
Notice :
• Make sure you use the correct trim strip
since there is a left and right side strip. The
flexible material should be facing forward
(Figure B).
9
USA
6.5 PREPARING THE WATER CONNECTION (A)
Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder
connections must be made before the water line is connected to the dishwasher’s water
inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose
line.
Check with your plumbing supply sources for the proper hose and 90° elbow and
necessary fittings for the water supply line. This material is not supplied, and must be
purchased separately.
WARNING
Installation should be performed by a qualified installer. Work by unqualified
persons could be dangerous and may void the warranty.
If the dishwasher is installed in a location that experiences freezing temperatures
(e.g. in a vacation home, cabin etc.), you must drain all the water from the
dishwasher’s interior. Water system ruptures that occur as a result of freezing are
not covered by warranty.
6.5.1 INSTALLING THE 90° ELBOW FITTING
(B)
CAUTION
Do not over tighten the 90° elbow. Doing
so may damage the water inlet valve and
cause a water leak.
If the water supply line is to be copper
tubing, make certain that the elbow has a
compression fitting. Apply Teflon tape or other
pipe sealant when required. Orient the water
supply connection downwards as shown in the
figure so the water line can be easily pulled
underneath or on the side of the dishwasher.
6.5.2 JUNCTION BOX PREPARATION (C)
Remove the junction box cover by removing
the screws as shown in the figure. They will be
reinstalled later.
10
USA
6.6 DRAIN PREPARATION
The dishwasher drain hose may be connected to the drain plumbing in one of three ways
(Figure A, B, C).
Notice :
• Either one of the above methods must be used or the dishwasher will not operate
properly.
• A hose that attaches to a sink spray can burst if it is installed on the same water line as
the dishwasher. If your sink has one, it is recommended that the hose be disconnected
and the hole plugged.
• The total length of the drain hose is 763/4” (1950mm). If a hose extension is required, a
drainage hose of equal quality must be used.
• The maximum length must not exceed 157 ½” (4000mm). Otherwise, the cleaning
process is negatively influenced.
6.6.1 UNDER THE SINK DRAIN
Install a Y-branch tail pipe. (Figure A)
Notice :
• You must add a loop at least 28" (710mm) above the floor of
the cabinet and above the drain connection in the drain hose
to prevent waste water from not draining properly, and causing
either poor washing results or a bad odor.
6.6.2 INSTALLING AN AIR GAP
If the local ordinance requires an air gap (Figure B).
Notice :
• Check with local ordinance for type of air gap required.
6.6.3 DISPOSAL
Remove the drain connection plug before attaching the drain
hose from the dishwasher.
Every disposal has a hook up for a dishwasher; consult your
disposer manual for correct connection. (Figure C)
11
USA
6.7 STEAM PROTECTION FOIL
Steam will form inside the dishwasher during operation. At the end of the cycle, when the
dishwasher door is opened, it is required to use a steam protection foil to prevent any
steam from collecting on the underside of the counter top.
6.6.2 FITTING THE PROTECTION FOIL
Before applying the steam protection foil to the
underside of the countertop, clean the area with
a damp cloth (as shown in Figure A). Once the
area dries, apply the steam protection foil.
The steam protection
foil will be applied at the
location where the hot
steam escapes when you
first open the door (as
shown in Figure B).
CAUTION
Steam protection foil must be applied
where the steam escapes when door is
first opened. Failure to install the steam
protection foil during installation can
lead to damage to the cabinets and
countertop.
12
USA
7. PLACEMENT OF DISHWASHER INTO THE OPENING
Now place the dishwasher into the opening and get ready to connect all hoses and
electrical connections.
CAUTION
Make sure all hoses
and electrical wire are
pulled through the side
opening of the cabinet,
no hoses are kinked
and all slack is taken
out as shown in the
above figure.
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL
CONNECTIONS
7.1.1 DRAIN HOSE CONNECTION
Connect the drain hose to the drain plumbing.
1.Use the supplied rubber connection hose and drain hose clamps to connect the
dishwasher drain hose to the plumbing drain connection.
2.Use the spring clamp to secure the rubber connection hose to the dishwasher drain
hose. Use the screw clamp to secure the rubber connection hose to the plumbing drain
connection.
Note that the marks on the
rubber connection hose
should be on the drain hose
side
13
USA
7.1.2 WATER SUPPLY CONNECTION
Water supply may be connected to the
dishwasher in one of two ways:
• With metal braided hose.
• With copper tubing.
7.1.3 BRAIDED HOSE/COPPER TUBING
After connections are made turn on the water
supply to check for leaks.
CAUTION
• Hot water supply line: Use minimum 3/8” O.D. copper tubing or metal braided
dishwasher supply line.
• Temperatures required for soldering and sweating will damage the dishwasher’s water
inlet valve so if any such operation is needed, keep the heat source min. 77/8” (200mm)
away from the dishwasher’s water inlet valve.
• There should not be any sharp bends in the water line that may restrict the water flow.
• Teflon tape or pipe tread compound must be used for sealing the connection. Before
connecting the copper water supply line to the dishwasher, flush it with hot water to clear
any foreign material.
Notice :
After connections are made turn on the water supply to check for leaks.
7.2 ELECTRICAL CONNECTION
WARNING
• Make sure the voltage and frequency listed on the data plate correspond with
the household electrical supply. This data must correspond to prevent injury and
machine damage. Consult a qualified electrician if in doubt.
• Only connect the dishwasher to the mains when all installation and plumbing work
is complete.
• Do not use any extension cord or portable outlet device to connect the dishwasher
to a power supply.
7.2.1 GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown, grounding
will reduce the risk of electric shock by providing a path of least resistance for electric
current. This appliance must be installed and grounded in accordance with all local codes
and ordinances.
WARNING
• Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service representative if you
are in doubt whether the appliance is properly grounded.
14
USA
Install a strain relief (not supplied) into the
opening on the kick plate. (Figure A)
Pass the electrical supply cable through the
strain relief; make sure the strain relief clamps
the insulated outer casing of your electrical
supply cord and not the wires themselves.
Leave 215/16” “ to 315/16” “ (75mm / 100mm)
of insulated wire extending through the strain
relief (Figure B). Tighten the strain relief
screws. (Make sure you can not pull the
electrical cord out) of the strain relief.
Do not pre-twist the wires before connecting
them with wire nuts.
Using the supplied wire nuts, connect the
electrical supply wires to the dishwasher’s
wires, black to black, white to white, and green
or bare to green or bare. Make certain that the
insulated wires show no bare wire from the
bottoms of the wire nuts. Gently tug the wires
to make certain they are securely connected
(Figure C).
7.2.2 FASTEN JUNCTION BOX
1. Pull the wires into the junction box. Be sure
that the wire nuts do not loosen.
2. Replace the cover on the junction box.
3. Secure the cover with the screws (Figure D).
15
USA
7.3 READJUSTING FOOT LEVELS
Now that the dishwasher is in the
cabinet you must readjust the feet to
bring the dishwasher up to the required
height and attach it underneath the
countertop.
1. Readjust the front foot levels with
adjusting wrench to balance the
dishwasher and raise it up under the
countertop, make sure the unit is level.
2. Readjust the rear foot levels with a
screwdriver to balance the dishwasher
and raise it to the required height using
the brackets supplied.
3. Attach the dishwasher underneath
the countertop with the four screws
supplied (Ø 1/8” x 1/8” - Ø 3.5mm
x 14mm). Make sure you do not go
through the top of the countertop or
damage granite.
7.4 ADJUSTING THE MOVABLE TOE KICK
Now that you have successfully installed the dishwasher, you
need to attach the toe kick to the dishwasher. The two piece
toe kick can be adjusted to the height and depth needed for
your kitchen. Be sure to use the slotted toe kick in the front
and the other behind it. They slide into each other.
1.Insert the movable toe kick brackets into the channel (A).
2.Make sure that the plastic tab to the left of the “L” opening
on the dishwasher has not closed the channel you will push
the bracket through.
Notice :
Be sure to notice there is a left and a right bracket.
Adjust the toe kick brackets forward or backwards so that they
will align with the kitchen toe kick (B).
16
USA
Lock the toe kick brackets as shown with the plastic
tab in the figure C by pushing the plastic tab on the
dishwasher into the teeth of the bracket (C).
3. Now attach the toe kick to the bracket with the
two (Ø 3/16” x 1/4” - Ø 4mm x 6mm) screws and
the caps provided as follows.
If the enclosure height is below 331/16” (840mm)
use only “o” labelled toe kick (toe kick without slots).
Installation should be done following the steps
illustrated in the Figures A, B and C respectively.
1. Bend tabs on toe kick (o) inwards (A).
2. Secure toe kick to brackets with screws (t) as
shown in the supply bags (B).
3. Attach caps (s) as shown in the supply bags (C).
If the enclosure height is above 331/16” (840mm)
use “o” and “p” labelled toe kicks together. Make
sure the slotted toe kick “p” is on the outside so you
can adjust height of the toe kick. Installation should
be done following the steps illustrated in the figures
A, B and C respectively.
1. Align the toe kick (o) and (p) (A).
2. Secure toe kicks to brackets with screws (t) after
adjusting the height of the slotted toe kick (p) (B).
3. Attach caps (s) as shown in the supply bags (C).
If the enclosure height is above 341/4” (870mm)
use “o” and “r” labelled toe kicks together. Make
sure the slotted toe kick “r” is on the outside so you
can adjust height of the toe kick. Installation should
be done following the steps illustrated in the figures
A, B and C respectively.
1. Align the toe kick (o) and (r) (A).
2. Secure toe kicks to brackets with screws (r) after
adjusting the height of the slotted toe kick (t) (B).
3. Attach caps (s) as shown in the supply bags (C).
17
USA
Notice :
Notice :
If the dishwasher does not operate properly,
refer to the self help hints.
The installer is responsible for the
dishwasher installation. Incorrect
installation is not covered by the warranty.
10. SELF HELP HINTS:
8. INSTALLER CHECKLIST
Your installer must have completed and
checked the following:
• The dishwasher is square and level.
• The dishwasher is fastened securely to the
cabinetry.
• The dishwasher door opens and closes
freely. The dishwasher door must close
without hitting any cabinetry or counter top.
• The inlet water supply is turned on and
checked for leaks.
• The drain hose has been connected and
checked for leaks. There must be no kinks
or obstructions in the drain hose.
• The drain hose must be installed with a 28"
(710mm) high drain loop for drain hook-ups
without any air removed.
• If the dishwasher drain is hooked up to a
garbage disposal, the drain hopper plug
must be removed.
• The spray arms are free and rotate freely.
• The rinse cycle has been run.
• The water level will be below the filter
screen after the end of the wash program.
It is normal to find some water in the drain
filter area.
• Set the water softener to the correct water
hardness for your area. If the dishwasher
drain is connected to a garbage disposal,
make sure that the drain/hopper plug has
been removed.
9. FINAL INSTRUCTIONS
1. Press the On/Off button to turn the
dishwasher on.
2. Power indicator light comes on.
3. Use the Cycle Select button to choose a
washing program.
4. Start the program with the Start/Pause
button.
5. Run the dishwasher through one complete
cycle. When the progress indicator light “End”
lights up, the wash cycle is completed. Use
the On/Off button to turn the dishwasher off.
18
The power indicator light doesn’t come on:
• Check to make sure the breaker to the
dishwasher is in the on position.
• Check all the wire connections in the
junction box are tight and not loose.
No Water is coming into the dishwasher:
• Check to make sure the hot water shutoff is in the ON position.
Water does not drain:
• Make sure drain hose is not kinked or
comes out of air gap next to the sink.
• Remove drain hose from disposal making
sure plug is removed.
Notice :
• If your dishwasher is not operating
properly after following these steps:
Contact your dealer to schedule an
authorized service agent to inspect your
new dishwasher for any function related
failure.
• The manufacturer warranty does not
cover installation or customer education
service visits.
You will find the model and serial number
information on the label located on the
right-hand side of the inner door of your
dishwasher, as shown above.
Notice :
Please make a copy of your invoice and
keep it with this manual and register your
dishwasher on-line.
USA
17 1799 01 00 AC-USA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising