Trixter Matrix Bike Owner's Manual

Add to my manuals
40 Pages

advertisement

Trixter Matrix Bike Owner's Manual | Manualzz

T

ABLE OF

C

ONTENTS

Safety Tips……………………………………………… Page 1

X-Bike™ Indoor Performance Bike

X-Biking™ Indoor Cycling Programmes

Setting up the X-Bike™ Indoor Performance Bike

Assembling the X-Bike™ Indoor Performance Bike

Adjusting the X-Bike™ Indoor Performance Bike

Using your X-Bike™ Indoor Performance Bike……….. Page 9

Equipment and Technical Specifications……...……….. Page 24

Exploded views and Parts Identification List ………….. Page 25

Warranty Statements and Registration Card……………. Page 32

S

AFETY

I

NFORMATION

WARNING

TO AVOID SERIOUS PERSONAL INJURY

Before beginning any fitness or conditioning program, consult with your physician or health official. This will establish the proper conditioning or fitness program that is appropriate for your age and physical condition.

Be safe. Prior to commencing each X-Biking™ Ride answer these questions:

Have you have been ill recently?

Have you have felt dizzy recently?

Have you have felt breathless recently?

Have you have had any chest pain recently?

Do you have an injury?

Are you pregnant?

Is there any reason why you think they should not exercise?

Are you over 35 years old and do not exercise regularly?

Have you have been told by a health practitioner that they shouldn’t exercise?

IF YOU ANSWER “YES” TO ANY OF THE ABOVE QUESTIONS YOU MUST SEEK

FURTHER ADVICE AND CLEARANCE FROM A MEDICAL PROFESSIONAL

PRIOR TO UNDERTAKING AN X-BIKING™ RIDE.

Fully read the owners manual and follow all instructions, which were written to ensure your safety and to protect the cycle. Note for Club Owners: To ensure the proper use and safety of the X-Bike™ Indoor Performance Cycle, make sure that all users refer to this manual.

The manual should be made available to all users.

Only operate the X-Bike™ Indoor Bike on a solid, level surface in a well lit and well ventilated area. Make sure the seat and handlebars are securely fastened before use.

Never allow children on the bike or allow children to play unsupervised near the bike.

Serious injury could occur due to a child’s curiosity or interest in the moving parts of the cycle.

It is important to properly set up the bike to your body type. The X-Bike™ Indoor Bike offers up/down and fore/aft adjustments that are clearly marked to ensure a quick and easy custom fit for each workout. Ensure that the rider compartment is securely tightened before use.

Check the cycle before each use. Never use the cycle if it is not completely assembled or is damaged in any way.

Never use an X-Bike™ Indoor Bike when ill or in a weakened condition.

The weight limit for this bike is 300 pounds. Do not use the X-Bike™ Indoor Performance

Bike if your body weight exceeds 300 pounds.

Always wear proper attire and footwear that fully covers your feet. Long hair should be tied back. Ensure that your laces are tucked into your shoes.

Always warm up before beginning to exercise or at the start of a workout.

1

Use care when getting on and off the X-Bike Indoor Performance Bike. Always wait until the pedals are completely stopped before removing your feet from the pedals or dismounting. Do not stand or climb on the handlebars.

Only ride or allow the X-Bike™ Indoor Performance Bike to be ridden under the supervision of a qualified X-Biking Instructor.

Keep hands away from moving parts and always ensure that hands are never placed in a position where these is no rubber handlebar grip.

Do not overexert yourself or work to exhaustion. If you feel faint, dizzy, short of breath, or if you have chest or other pains, STOP IMMEDIATELY! Consult your physician before you continue.

Ensure that you have a water bottle with at least 300ml beverage and wear a towel in the rear pocket of your riding top to absorb sweat from your body and the handlebars.

Never ride the X-Bike™ Indoor Performance Bike in a standing position at high revolutions per minute (RPM).

Always maintain your pelvis over the centre line of the X-Bike™ Indoor Performance Bike.

Never adjust the resistance of the flywheel and the resistance of the X-Bars™ Handlebar

System when standing.

Do not use accessory attachments that are not recommended by the manufacturer – such attachments might cause injury or damage to the bike and will affect the warranty of the Bike.

As a gesture of courtesy to the next user and to maintain the high quality of the X-Bike™

Indoor Cycle, please ensure that it is wiped down after each use.

If any issues arise affecting the performance of the X-Bike™ Performance Bike, please inform the X-Biking™ Instructor and ensure that wear parts are checked regularly.

This warning or the Owner’s Manual does not replace the need to be alert and to use your common sense when using the X-Bike™ Indoor Performance Bike.

2

I

NTRODUCTION

X-Bike™ Indoor Performance Bike

Congratulations on purchasing your Trixter Enabled Matrix X-Bike™ Indoor Performance Bike, one of the most revolutionary cycles available to the fitness market. The X-Bike™ Indoor Cycle will offer you an unrivalled whole body workout by introducing real bike upper-body movements. It has been designed to simulate the real physiological demands experienced throughout the body when cycling…an exercise often mimicked yet never equalled. Climbing out-of-the-saddle, accelerating, and recovering are dynamic total-body actions for everyone riding bicycles outdoors. Climbing steep hills and sprinting involve significant upper body and core muscle recruitment to control the lowerbody and the movement of bicycle beneath the rider. The X-Bike™ Indoor Cycle, featuring the X-

Bars™ Handlebar System, provides an effective and realistic means of accessing this unique level of fitness. Welcome to the X-Biking™ Indoor Cycling revolution!

X-Biking™ Indoor Cycling Programs

Trixter's visionary X-Biking™ Group Cycling Programmes are ideal for people of all ages, abilities, and fitness levels. Workouts are designed by experienced cycling coaches and elite athletes to maximize the exercise benefits of the Matrix X-Bike™ Indoor Cycle. It’s the only total-body cardiovascular group exercise workout based on a vibrant, engaging, and real outdoor sport - mountain biking! During the immersive, fun-fit classes, you ride with a certified X-Biking™

Instructor to the sound of custom beats over a variety of simulated trails. Techniques like

"pumping" up a climb, banking the bars side-to-side to swoop through turns, and even coasting on the X-Bike’s unique freewheeling platform provide essential and natural muscular conditioning to dramatically enhance the rider's experience.

Before You Begin

Prior to leaving the manufacturing facility, your X-Bike™ Indoor Cycle was thoroughly inspected and tested for proper operation. To minimize shipping damage, careful attention was given to making the bike ready for shipment.

Dimensions of the X-Bike

Length

Width

Height

Weight

Inch/lb mm/kg

47.5 1185

Your Matrix X-Bike™ Indoor Mountain Bike will have arrived in 1 carton. Upon arrival, fully inspect the carton for damage. Point out any damage to the delivery person and have the delivery person record the damage on the delivery paperwork. Contact the Customer Service Department to report any damage (See details at the back of this Manual). Please follow these detailed instructions and you will find that your new X-Bike™ Indoor Mountain Bike can be unpacked and assembled with ease.

3

I

NSTALLATION &

A

DJUSTMENT

SETTING UP THE X-BIKE

Indoor Performance Cycle

A. Remove the bike and components from the shipping carton

1.

With assistance, move the box to the desired location in a well-lit and well

- ventilated area. Ensure that the carton is standing upright and remove the strapping material.

Ensure that you allocate sufficient floor space for the safe operation of the X-Bike after it has been assembled.

2.

Pull the cardboard edge along the top of the box and carefully remove and dispose of the staples.

Remove the boxes of contents enclosed with the frame.

3.

Open each box and ensure that you have the following parts necessary to assemble your X-

Bike™ Indoor Cycle:

B. Assembling the Bike

• X-Bike™ Indoor Cycle Frame x 1

• X-Bars™ Handlebar System Head Unit x 1

• Handlebar Assembly x 1

• X-Bars to X-Bike Adaptor x 1

• Seat x 1

• Seat Post x 1

• Leveller Feet x 4

• Quick Release x 1

• Base Leg Front x 1

• Base Leg Rear x 1

• Bolts, Nuts and Washers for legs x 4sets

• Pedals x 1L & 1R

All references to the right or left side and to the front or back are made as if you were sitting on the exercise bike ready for use. For example, the chain guard is on the right side of the bike and the flywheel is at the front.

1.

With the help of an assistant, lift the bike frame out of the carton and remove all protective packaging.

2.

Screw the 4 leveller feet into the front and rear legs.

Leveller Foot

4

3.

Fit the legs onto the frame ensuring that the leg with the wheels is fitted to the front and the leg without wheels is fitted to the back. Make sure that the wheels are facing towards the front and that the feet are facing downwards. Insert the M10 bolts provided facing downwards ensuring that you have a washer above and below the leg. Fit the M10 Nut and tighten securely.

Note: If you are having difficulties threading the nut onto the bolt, with assistance prop up the base leg and the frame on wooden blocks to gain easier access to the nut underneath.

4.

Adjust the 4 leveller feet to ensure that each corner is fully supported on the floor. Once adjusted, lock the position by tightening the lock wing nut inside the leveller feet.

5.

Slide the seat post into the seat tube at the rear of the frame and tighten the adjustable quick release knob until you are ready to set the height position. Slide the seat assembly onto the seat post and fit the quick release handle provided from the bottom upwards. Fit the thumbscrew at the top of the quick release bolt to secure until you are ready to set the fore/aft position.

Seat Fore/Aft Adjust Lever

Seat Height Adjuster Knob

6.

To fit the X-Bars™ Handlebar System Head unit, you must first fit the adaptor. Remove the bottom cover by undoing the 2 M4 Hex head screw. This will give access to the main X-Bars frame internally. The adaptor should be fitted so that the head post is facing downwards and towards the rear of the assembly.

Insert the 4 x M8 bolts provided with the adaptor towards the rear, and ensure that the washer is placed behind the M8 Nut and tighten securely. Refit the bottom cover.

7.

The X-Bars System assembly is inserted into the head tube with the head of the assembly facing towards the front of the bike. Tighten the adjustable quick release knob until you are ready to set the head height position.

Note the orientation of the

Handlebar and Bar Ends.

Height Adjuster Knob

5

8.

Loosen the Handlebar clamp on top of the X-Bars Handlebar System Head Unit to gain access for the handlebar fitment. Place the handlebars into the clamp so that the bar ends are facing towards the front of the bike and the Grip-shift™ is on the right hand side of the bike. Place the marked clamp area of the handlebars centrally in the clamp to ensure to provide maximum grip from the clamp. Refit the top of the clamp ensuring the there is an even pressure applied to all four bolts. Just before the clamp takes pressure, adjust the orientation of the bars so that the exit route of the Grip-shift™ has approximately 5mm (1/4”) clearance with the top of the Cover.

Tighten securely.

Note orientation of handlebar and position of Grip-shift™

9.

Fit the pedals, which are marked as if you are seated on the bike, “R” for right and “L” for left.

Carefully thread the right pedal in the crank with your fingers – do not cross thread the pedal in the crank arm. Use a size 15 wrench tool to tighten the pedal. Repeat the step for the left pedal.

Do not over-tighten.

Note: The left pedal is reverse-threaded.

10.

Use a soft clean cloth to wipe off dust that may have accumulated during shipping.

11.

The X-Bike™ Indoor Cycle is now ready to set up for use.

Adjusting the Bike

Seat Adjustment

1.

Rotate the pedals so that one of the pedals is in the upward position.

2.

Place your foot in the toe clip of the pedal closest to the floor and mount the bike. Ensure that the ball of your foot is over the centre of the pedal. Your leg should be slightly bent at the knee as shown in the picture below.

6

3.

If your leg is too straight or your foot cannot touch the pedal, you will need to lower the seat. If your leg is bent too much, you will need to raise the seat.

4.

To adjust, dismount the bike and release the quick release knob for the seat height adjustment.

Once loosened you may slide the seat post up or down as necessary. When the seat is in the desired position, reapply the quick release knob to lock the position. Note the final position mark on the seat stem for future use.

5.

Adjusting the fore or aft allows for better fit. To adjust, dismount the bike and release the quick release lever under the seat and slide the seat forward or backward as desired. Re-apply the quick release clever to lock. Note the final position mark on the seat stem for future use.

Adjusting the Flywheel Resistance

The X-Bike™ Indoor Performance Bike will arrive with the resistance system set up on the handlebars already, but may require minor adjustment after the handlebar assembly has been fitted onto the X-Bars™ System Head Unit. Minor adjustment can be achieved by turning the adjuster wheel at the cable exit on the Grip-shift™ either clockwise or counter-clockwise depending on whether it need to be increased or decreased.

If the resistance needs more adjustment than is available in the minor adjustment block, it can be set up as follows:

1.

Turn the minor adjuster wheel on the Grip-shift™ fully counter-clockwise so that there will be sufficient cable in the minor adjustment block for future regular checks

Minor Cable Adjuster Cable Release Bolt

2.

Using a 6mm Hex key, loosen the bolt at the bottom of the V-Brake to release the cable for adjustment.

3.

Turn the Grip-shift™ fully clockwise to the minimum resistance setting. Using one hand, compress the 2 pads of the V-Brake to just make contact with the flywheel. Pull the excess cable until it is tight in the cable clamp. Retighten the bolt to secure the cable.

4.

The resistance is set, when the minimum setting is free from contact with the flywheel and position 2 just begins to make slight contact. Minor adjustment can be achieved by screwing the minor adjustment wheel where the cable exits from the Grip-shift™.

7

Handlebar (Bar Height) Adjustment

1.

If you own a road or mountain bike, this position can be taken from your chosen set up. Place a straight edge ruler on top of your bikes saddle and extend it over the handlebar, making sure that the ruler is level or parallel with the ground. Measure the distance from the bottom edge of the ruler to the top of the handlebar and replicate this measurement on the X-Bike™ Indoor Cycle.

2.

To adjust, dismount the bike and release the quick release knob on the head tube for the handlebar adjustment. Raise or lower the X-Bar™ System headstock until the required measurement has been achieved. Reapply the quick release knob to lock. Note the final position mark on the handlebar stem for future use.

3.

If you do not own a bike and are setting the height up for the first time it is suggested to set the handlebars at the same height as the seat for a datum and then try different heights to get the arrangement most suitable for you.

Pedal Strap Adjustment

1.

Place the ball of each foot on the pedal and in the toe clip such that the ball of the foot is centred over the pedal spindle (centre of the pedal)

2.

Rotate one foot to within arms reach and pull up on the toe clip strap. Repeat for the other foot.

3.

Keep your knees over your foot as you pedal.

8

U

SING

Y

OUR

X

-

B

IKE

I

NDOOR

P

ERFORMANCE

B

IKE

THESE GUIDELINES ARE DIRECTED TO YOU AS THE OWNER OF THIS

EXERCISE EQUIPMENT AND YOU SHOULD INSIST THAT ALL USERS

FOLLOW THE SAME GUIDELINES. YOU SHOULD MAKE THIS MANUAL

AVAILABLE TO ALL USERS.

General Exercise Guidelines

You should only undertake an exercise program using an X-Bike™

Indoor Cycle, under the supervision of a qualified X-Biking™ Instructor.

Trixter, Its Distributors and Sales Agents do not accept responsibility for any injury, which may occur whilst riding unsupervised and without proper instruction.

Pedalling

1. Obtain a complete physical examination from your medical doctor and ensure to follow the recommended training profiles suitable for your current health status.

2. The speed and duration of your exercise program should always be subject to how you feel.

Never permit peer pressure to exceed your personal judgement while exercising.

3. When working out for the first time, start out slowly for a minimum of five minutes. After your muscles have warmed up, gradually increase the pedalling rate and/or resistance to a speed that allows you to attain a comfortable training threshold. If you have access to a heart rate monitoring device, you can set your speed and resistance that allows you to attain your target heart rate zone.

Pumping the X-Bars

1. Once you are confident with the pedalling motion of the X-Bike, set the flywheel resistance to a comfortable setting and get into a standing position on the bike while continuing to pedal at a steady rate. To familiarise yourself with the pumping motion, set the handlebar resistance to minimum by twisting the handlebar resistance knob at the side of the X-Bars™

Handlebar System fully counter-clockwise and begin to “pump” the bars left and right in time with your pedalling rhythm in a similar fashion as if you were riding a bike. This natural cycling movement comes by ensuring that your right arm and left leg go down at the same time and your left arm and right leg go down at the same time.

2. Overweight individuals should be particularly cautious when using the equipment for the first time. Even though such individuals may not have histories of serious physical problems, they may perceive the exercise to be far less intense than it really is, resulting in the possibility of overexertion or injury.

3. Although all equipment manufactured by Trixter has been thoroughly inspected by the manufacturing facility prior to shipment, the purchaser is responsible for proper assembly and installation of the X-Bike indoor performance bike.

9

Mounting and Dismounting

Once sitting comfortably on the Bike, make sure to tighten each toe strap securely before commencing exercise. Dismount the bike by first loosening each toe clip and then removing your feet from the pedals. Carefully step off the bike.

Your First Workout

Basic Instructions

Once an instructor has helped you to properly adjust the bike to your body size and you are sitting comfortably on the bike, slowly begin pedalling. Allow your hands to rest comfortably on the handlebars.

If at any time during your workout you feel chest pain, experience severe muscular discomfort, feel faint, or are short of breath, STOP EXERCISING IMMEDIATELY. If the condition persists, you should consult your medical doctor immediately.

Pedalling Resistance

Pedalling resistance is controlled by the turning of the Twist-grip™ located on the right side of the handlebar. The minimum resistance setting is located with the Twist-Grip™ turned fully clockwise

– increasing to a maximum Resistance when the Twist-Grip™ is turned fully counter-clockwise. It may be adjusted at any time during exercising by turning the Twist-grip™ to the desired resistance setting.

X-Bar™ Handlebar System Resistance

Handlebar resistance is controlled by the knob located at the end of the resistance damper on the right side of the head section. There are seven settings from minimum to maximum. The resistance can be adjusted at any time by twisting the knob anti-clockwise for minimum and clockwise to maximum setting.

* Your instructor will advise you on the correct use of the X-Bars™ System.

10

M

AINTENANCE

I

NSTRUCTIONS

Helpful Hints

The safety level given by the design of X-Bike™ Indoor Performance Bike can only be maintained when the equipment is regularly examined for damage and wear. Inoperable components should be replaced or the equipment should be put out of use until it is repaired. Read all maintenance instructions before beginning work.

All references to the right or left side and to the front or back are made as if you were sitting on the exercise bike ready for use. For example, the chain guard is on the right side of the bike and the flywheel is on the front.

For identification purposes, the serial number of the X-Bike™ Indoor Cycle is located on the front support Leg and the serial number for the X-Bars™ System is located internally on the main base plate, which can be accessed by removing the bottom cover.

Front of Bike Frame

Serial Number

Tool List

The following tools will be needed to carry out service and maintenance:

• Combination wrench including 10mm, 13mm, 15mm, and 17mm

• Metric Hex Keys (long) set including 2.5, 3, 4, 5, 6, and 8mm.

• Genuine X-Bike BB Lock Ring removal tool.

• Phillips screwdriver

• Bicycle crank arm puller

• Bottom Bearing Cup tool

• Shimano® compatible bottom bracket tool and 1/2 “ driver

• Pliers

• Pedal Spanner (15mm)

11

Preventative Maintenance

Refer to the appropriate Parts Removal and Replacement section on PAGES 19-28 for all disassembly and assembly instructions. If you experience any problems, contact your Matrix Fitness

Systems service department (Details found at www.matrix-fitness.com

).

CHECKLIST OF ROUTINE MAINTENANCE REQUIREMENTS

Daily

1.

Wipe Down the X-Bike™ Indoor Cycle

2. Inspect for loose components and tighten where necessary

Weekly

1. Inspect the Wear Pads for excessive wear or dryness

2. Lubricate the Flywheel

3. Lubricate the Drive Chain

4.

Clean the X-Bars™ System and X-Bike™ Indoor Cycle

Monthly

1. Inspect the Chain Tensioning

2.

Inspect the X-Bars™ System damper performance

3.

Inspect the X-Bars™ System ‘Return to Zero’ Performance

4.

Inspect the rigidity of the X-Bars™ System to check for looseness in the mechanism.

5. Inspect the Centre Slider for wear

6. Inspect the Damper slider for wear

7. Inspect the seat and handlebars post adjustment for secure height adjustment tightening

Daily

1. Wipe down the X-Bike after each use to remove sweat and moisture. Use soap and water, or a diluted non-abrasive domestic cleaner solution. Rinse to remove detergent residue and then dry off.

2. If the bikes are used frequently in group exercise sessions, inspect for loose components such as pedals or cranks prior to commencing the next class. Tighten up any loose parts.

Weekly

1. Inspect the resistance wear pads for excessive wear or dryness. If necessary lubricate the pads with GT-85 or another PTFE based lubricant. As the pads wear with use, it will be necessary to adjust the resistance cable to compensate. The resistance cable can be adjusted as follows; o

Turn the minor adjuster wheel on the Grip-shift™ fully clockwise so that there will be sufficient cable in the minor adjustment block for future checks. o

Using a 6mm hex key, loosen the bolt at the bottom of the V-Brake to release the cable for adjustment.

Minor Cable Adjuster Cable Release Bolt

12

o

Turn the Grip-shift™ fully clockwise to the minimum resistance setting. Using one hand, compress the 2 pads of the V-Brake to just make contact with the flywheel.

Pull the excess cable until it is tight in the cable clamp. Retighten the bolt to secure the cable. o

The resistance is set, when position 1 or minimum setting is free from contact with the flywheel and position 2 just makes contact. Use minor adjustment if required. o

If the pad thickness is reduced to less than 4mm, they need to be changed. (See Pad

Changing instructions in Parts – Removal and Replacement)

2. Wipe down the flywheel with WD-40® or equivalent light oil spray. This lubricant will clean the surface of the flywheel and help prevent rust.

3. Lubricating the chain – Using a spray can with an extension nozzle; you can gain access to the chain from the front of the chain guard with general light maintenance oil.

4. To keep the X-Bike looking new, wipe the general bodywork of the X-Bike and X-Bars with a clean damp cloth. Use conventional dish washing detergent but never use abrasive materials to clean the bike. Be certain to wipe off all traces of perspiration when you are finished as it contains salt and other corrosive substances that can damage surfaces and/or leave a white residue.

5. If you should need assistance or service, contact your Matrix service department

(See details at www.matrix-fitness.com

).

Monthly

1. Chain Tensioning

Inspect the chain for tensioning by rotating the crank to drive the flywheel forward. Do this motion in ¼ turns to assess if there is free play between the crank and the flywheel.

Tensioning the flywheel is achieved by adjusting the bolts in the front forks of the bike, which set the position on the flywheel axle in the frame. To Tension the chain, undo the axle nuts on either side of the flywheel enough to release the grip and allow the flywheel to move.

Axle Position Markings Chain Adjusting Bolts

Turn the chain tensioning bolts on both sides of the frame by the same amount to ensure correct alignment. Continue to adjust in small amounts until the chain slack is eliminated and the flywheel can rotate freely without pulling the pedals around with it.

2. X-Bars™ Handlebar System Damper Performance

Examine the damper for smoothness and consistency of movement. This is determined by testing the movement in the handlebars firstly in minimum and then in maximum resistance setting. a. Air Cavitations - At minimum, the movement should be light and smooth without the presence of the sound of air cavitations. This would be a sound you could expect with the presence of tiny air bubbles in the system, which will affect the consistency

13

and quality of resistance. If cavitations are present, the damper should be replaced.

See replacing the damper in Parts – removal and replacement section. b. Sticking - At maximum setting, the handlebars should move from fully left to fully right consistently without any sticking action. Over time, the moving parts can wear and lead to resistance tolerances being affected. If the movement in the handlebars experiences sticking, the damper should be replaced. See replacing the damper in

Parts – removal and replacement section.

3. X-Bars™ Handlebar System ‘Return to Zero’ Performance

Examine the action of the ‘Return to Zero’ springs on the handlebar system by setting the resistance at maximum. Move the bars to the extreme right and release and then extreme left and release. At this setting the mechanism should return close to centre under its own action.

If it is found that the handlebars remain unreasonably fixed to one side or the other, the springs will need to be replaced. See replacing the ‘Return to Zero’ springs in Parts – removal and replacement section.

4. Looseness in the X-Bars™ Handlebar Mechanism a. Mechanism Hardware - Examine the handlebar system assembly for general mechanism looseness. Check all 4 main pivot bolts, the 2 large bolts in the centre of the assembly, and the main damper pin through the end of the damper. If any looseness is present, tighten before reassembly. In the event that any of these bolts have been found to be loose, they should be checked again at the next weekly maintenance routine and if they have re-loosened, please contact your authorised dealer. (Details for your closest dealer found at www.matrix-fitness.com

)

Main Pivot Bolts Centre Bolts

Centre Slider Damper Slider b. Slider wear – There are three sliders in the mechanism, 1 in the centre swinger and the other 2 running in the damper rails. If the clearance between these sliders and the rails in which they run exceeds 1.5mm, they should be replaced.

5. Height Adjustment

Dryness or prolonged use may cause the height and reach adjustments for the bars and seat to become tight. If this is the case, the sliding assembly should be removed from the frame and have a smear of light duty grease applied along the sliding surface before reassembly.

Similarly, apply some light grease to the clamping assembly to ensure it does not seize up.

Clean off excessive grease before reassembly.

14

P

ARTS –

R

EMOVAL AND

R

EPLACEMENT

WARNING:

It is vitally important to keep the X-Bike™ Indoor Cycle properly maintained but if you are unsure about any of the procedures for the removal or replacement of parts, you are recommended to contact your authorised dealer.

NOTE: When carrying out any service or maintenance procedures, it is vital to ensure that ALL hardware has been fully tightened and the assembly is returned to its original assembly state prior to allowing the X-Bike™ Indoor Cycle to be used. If in doubt, contact your authorised dealer.

Replacing the Resistance Pads

1. If the pad thickness is reduced to less than 4mm, they need to be replaced.

2. Using a 6mm hex key, loosen the bolt clamping the resistance cable to release the V-brake mechanism.

Cable Release Bolt

3. Remove the screw at the back of the pad housing to release. Drop the pad out of the assembly.

4. Fit new pad into the V-Brake assembly on both sides. Refit the screws complete with the spring and washers. Tighten to within 2 full turns from the end.

5. Turn the Grip-shift™ fully clockwise to the minimum resistance setting. Using one hand, compress the 2 pads of the V-Brake to just make contact with the flywheel. Pull the excess cable until it is tight in the cable clamp. Retighten the bolt to secure the cable.

6. The resistance is set, when the minimum setting is free from contact with the flywheel and position 2 just makes contact.

Removing the Chain Guards

Outer Guard

1. Remove the 3 bolts holding the outer guard to the frame. These bolts are 1 at the rear, 1 underneath and 1 between the flywheel and the right hand fork (Left if you look into the bike from the front where it is accessed)

Bolt 1 Bolt 2 Bolt 3

15

2. Turn the right hand crank arm vertically downwards as this allows the outer guard to be removed more easily.

3. Ease the outer guard away from the inner guard taking care not to damage the protective seals between it and the inner guard. Once free, remove the seal from the bottom of the cover to allow a little more room for removal.

4. Carefully manoeuvre the guard, bottom first away from the frame and orientate it to fit around the crank and the pedal. Once removed, you have full access to the drive train.

5. Refitting the chain guard is simply to carry out actions 1 to 4 in reverse.

Inner Guard

1. Follow procedure for “removing the pedal crank arms” below.

2. Undo 3 bolts fastening the inner guard to the frame.

3.

To refit follow steps 1 and 2 in reverse.

Removing the Flywheel

1. Follow the procedures shown above for removing the chain guard.

2. Loosen the nuts on either side of the flywheel axle enough to allow the flywheel to move freely in the axle slide on the frame.

3. Turn the 2 chain tensioning bolts on the front forks counter-clockwise until they are fully removed from the flywheel bracket.

4. The flywheel axle can then be removed from the slide taking care to support its’ weight when it drops out (40 pounds/18.2kg). Care should also be taken not to drop the flywheel onto the frame below, as the paintwork will be damaged.

5. The chain can now be eased off over the front chain sprocket.

6. The flywheel is replaced by following steps 1 to 5 in reverse.

7. To Tension the chain, turn the chain tensioning bolts on both sides of the frame by the same amount to ensure correct alignment. Continue to adjust in small amounts until the chain slack is eliminated and the flywheel can rotate freely without pulling the pedals around with it.

Replacing the Chain

1. Follow the procedures shown above for removing the outer chain guard.

2. Follow the procedures shown above for removing the flywheel.

3. Replace with new chain in a similar fashion and repeat the procedures above in reverse to reassemble.

4. To Tension the chain, turn the chain tensioning bolts on both sides of the frame by the same amount to ensure correct alignment (Check the alignment by counting the marks on the flywheel bracket on both sides of the frame). Continue to adjust in small amounts until the chain slack is eliminated and the flywheel can rotate freely without pulling the pedals around with it.

16

Replacing the Handlebars

1. NOTE: Your X-Bike™ Indoor Performance Bike has been fitted with 580mm long handlebars as standard. You must ensure that the new bars to be fitted are within the recommended maximum length of 580mm with a tube wall thickness not less than 3.2mm and are the correct diameter 25.4mm at the clamping section.

2. As you will probably intend to use the existing Grip-shift™ mechanism, you should first remove these parts from the existing assembly.

3. Remove the bar-ends by using a 6mm hex key to loosen the bolt under the clamp.

4. Carefully prise inside the rubber handlebar grips with a small flat head screwdriver and spray some WD-40© or equivalent light oil spray. Ease the grips from either end of the handlebars.

5. Using a 6mm hex key, loosen the 4 bolts from the handlebar clamp on the top of the X-

Bars™ Handlebar System to release the grip on the handlebar.

6. Twist the handlebar to expose the bolt holding the Grip-shift™ and using a 2.5mm hex key loosen this bolt. Slide the assembly off the end of the bars.

7. Remove the 4 bolts from the handlebar clamp on the top of the X-Bars™ Handlebar System.

Remove the bars from the clamp housing.

8.

Fit the new bars ensuring that the orientation of the bar sweep is faced toward the rider as shown. Replace the clamp cap and leave slightly loose until the Grip-shift™ has been refitted and tightened.

9. The Grip-shift™ should be refitted to the right side of the bars ensuring that the cable exit is facing back toward the user with about 5 to 10mm clearance between it and the top of the cover.

Note the orientation of the handlebar and bar ends.

10. Tighten the 4 clamp bolts ensuring a) that the marked clamping area of the bars is central within the clamp and b) the clamp is tightened evenly by all 4 bolts (This can be verified by checking the width of the gap on both sides of the bars – it should be the same).

11. Using conventional hair spray, apply a film of spray to the inside of the grips before fitting onto the ends of the handlebars. The hairspray dries rather quickly and it is recommended to get the grips in place without delay ensuring to leave enough space at the end of the bar for the bar ends. (The reason for the hair spray is that it acts briefly as a lubricant but then dries to create a good grip with the bar).

12. Refit the bar-ends and fully tighten all points before riding the bike.

Replacing the Grip-shift™

1. For removal of the old Grip-shift™, follow procedures 3 to 7 within the section for

“Changing the handlebars” above. As the Grip-shift™ is removed from the right side only, you do not nave to touch the left side of the handlebars.

2. Using a 6mm hex key, loosen the bolt at the bottom of the V-Brake to release the resistance cable.

17

3. Pull the resistance cable out of the assembly and all the way through the outer sleeve at the top of the bike (You will have to cut off the protective nipple at the end of the cable using a snips in order pull it through the sleeve).

4. Ensure that you only use recommended replacement parts as other units may not perform as intended and will affect the warranty on the bike.

5. From the new Grip-shift™, feed the cable down through the outer sleeve and in through the

V-Brake assembly. (Fit a new protective nipple to the end of the cable by squeezing with pliers).

6. Place the handlebars back into the top clamp and tighten up by following procedures 8 to 12 within the section for “Replacing the Handlebars” above.

7. To set the resistance, turn the Grip-shift™ fully clockwise to the minimum resistance setting. Using one hand, compress the 2 pads of the V-Brake to just make contact with the flywheel. Pull the excess cable until it is tight in the cable clamp. Retighten the bolt to secure the cable.

8. The resistance is set, when the minimum setting is free from contact with the flywheel and position 2 just makes contact.

Removing Pedal Crank Arms

Left Crank Arm

1. Use an 8mm Hex key to remove the pedal crank bolt.

2. Thread a bicycle crank arm puller onto the crank arm shaft.

3. As you tighten the crank arm puller on the shaft, the crank arm will be extracted from the crank arm shaft. Remove the crank arm from the frame.

4. Apply a thin coat of grease on the right bottom bracket shaft and install the right crank arm on the bottom bracket spindle. Align the right crank arm 180º from the right crank arm and push the crank arm onto the crank arm shaft.

5. Apply 1-2 drops of Loctite® 222 on the left crank arm bolt threads. Install the crank arm bolt and tighten to secure the crank arm. Rotate the pedals a few revolutions and then tighten the crank arm bolt again to ensure that the crank arm is tightened to a torque of

22ft/lb (30Nm)

NOTE: Inspect the Pedal crank arm bolts again after 30 hours (approx. one week). If loose, remove the bolts; apply Loctite®222 and reinstall. Retighten the bolts to 22ft/lb (30Nm).

Monitor over the following week and if the problem persists, contact your service department (Details for your closest dealer found at www.matrix-fitness.com

).

Crank Bolt Removal Crank Arm Puller

18

Right Crank Arm

1. Follow procedures for “Removing the Chain Guard” above.

2. Use an 8mm Hex key to remove the pedal crank bolt.

3. Thread a bicycle crank arm puller onto the crank arm shaft.

4. As you tighten the crank arm puller on the shaft, the crank arm will be extracted from the crank arm shaft. Remove the crank arm from the frame.

5. Apply a thin coat of grease on the right bottom bracket shaft and install the right crank arm on the bottom bracket spindle. Align the right crank arm 180º from the left crank arm and push the crank arm onto the crank arm shaft.

6. Apply 1-2 drops of Loctite® 222 on the left crank arm bolt threads. Install the crank arm bolt and tighten to secure the crank arm. Rotate the pedals a few revolutions and then tighten the crank arm bolt again to ensure that the crank arm is tightened to a torque of

22ft/lb (30Nm)

7. Refit the Chain guard by following procedures for “Removing the chain guard” above.

NOTE: Inspect the Pedal crank arm bolts again after 30 hours (approx. one week). If loose, remove the bolts; apply Loctite®222 and reinstall. Retighten the bolts to 22ft/lb (30Nm).

Monitor over the following week and if the problem persists, contact your service department (Details for your closest dealer found at www.matrix-fitness.com

).

Tightening the Bottom Bracket Bearings

1. Follow procedures for “Removing the chain guard” above.

2. Then follow the procedures for removing the pedal crank arms above.

3. Loosen the locking cap on the left side of the bike using the locking cap removal tool.

4. Ensure that the right bearing cup is tight. If necessary, tighten with the bottom bearing cup tool. Note: the right bearing cup is reverse threaded.

5. Check the left bearing cup. If the bearing cup is loose, tighten with your fingers. Then use the bottom bracket tool to tighten the bearing cup by rotating the bottom bearing cup tool an additional 10º clockwise.

6. Verify that the bottom bracket spindle is not loose by tugging on the spindle shaft.

7. Use the lock ring removal tool to tighten the lock ring. Note: Prevent the left bearing cup from spinning by stabilizing it with the bottom bearing cup tool.

8. Apply a thin coat of grease on the left bottom bracket shaft and install the left crank arm on the bottom bracket shaft. Apply 1-2 drops of Loctite® 222 on the left crank arm bolt threads. Install the crank arm bolt and tighten to secure the crank arm. Rotate the pedals a few revolutions and then tighten the crank arm bolt again to ensure that the crank arm is tightened to a torque of 22ft/lb (30Nm)

9. Apply a thin coat of grease on the right bottom bracket shaft and install the right crank arm on the bottom bracket spindle. Align the right crank arm 180º from the left crank arm and push the crank arm onto the crank arm shaft. Apply 1-2 drops of Loctite® 222 on the left crank arm bolt threads. Install the crank arm bolt and tighten to secure the crank arm.

Rotate the pedals a few revolutions and then tighten the crank arm bolt again to ensure that the crank arm is tightened to a torque of 22ft/lb (30Nm)

10. Follow procedures for “Replacing the Chain” and complete the operation by adhering to the section for “Removing the Chain Guard”

NOTE: Inspect the Pedal crank arm bolts again after 30 hours (approx. one week). If loose, remove the bolts; apply Loctite®222 and reinstall. Retighten the bolts to 22ft/lb (30Nm).

Monitor over the following week and if the problem persists, contact your service department (Details found at www.matrix-fitness.com

).

19

Removing Pedals

1. Block the crank arm from spinning, and use a bicycle pedal wrench (15mm) on the pedal nut to remove the pedal from the crank arm.

2. Left Pedal: Turn the pedal nut clockwise and remove the pedal from the Pedal crank.

3. Right Pedal: Turn the pedal nut counter-clockwise and remove the pedal from the Pedal crank.

4. Install the new pedals by lightly greasing the threads and reversing steps 1 to 3.

Replacing the Saddle (from the seat post)

1. Using a 6mm hex key, loosen the bolt to release the seat clamp.

Seat Clamp Bolt

2. Lift the seat off the seat post.

3. Position the new seat on the seat post, level and align the seat as required, and tighten the clamp securely.

Removing the X-Bars Covers

Top Cover

1. First remove the handlebar complete with bar-ends and Grip-shift™ from the top clamp

(see “replacing the handlebar” section above).

Front Bolts

Rear Bolts

20

2. Undo the Top Covers – at the front and rear by using a 4mm extended hex key. Carefully lift the top cover (front and rear) upwards over the top clamp.

3. To reassemble, carefully position the covers back onto the assembly by easing it downwards over the top clamp until the holes are lined up on the internal assembly.

4. Thread all bolts before tightening any one to ensure that the holes are correctly lined up.

5. Take care to ensure that the seal is correctly secured into the groove on the top bar of the assembly before fastening back onto the assembly.

Side Covers

1. Using a 4mm hex key, remove the 4 bolts holding the side cover onto the assembly to gain access.

Side Cover Bolts

2. When removing the cover from the right side, take care not to damage the brush seal when removing over the damper adjuster.

3. When refitting, thread all 4 bolts before tightening any one to ensure that the holes are correctly lined up.

Bottom Cover

1. Using a 4mm hex key, remove the 2 bolts holding the bottom cover onto the assembly to gain access.

Bottom cover bolts

2. Drop the bottom cover downwards from the assembly.

3. Refitting is simply to locate the fixing holes and fit the bolts back in.

Replacing the Damper

1. For this section, only replace with genuine damper recommended by Matrix.

2. Remove all covers as directed in the “Removing the X-Bars Covers” section.

3. Using a 13mm wrench remove the nut from the fixed end of the damper.

4. Using 10mm and 13mm wrenches, undo the nut from the damper pin at the moving end of the damper. Remove all components from damper pin noting their position for reassembly.

5. Install the new damper and slide moving eye onto the slider pin. Thread the nut to hold in place.

6. Locate the fixed end of the damper into the bracket on the assembly and fit the nut. Tighten securely.

7. Tighten the moving end securely.

8. Refit the covers as directed in the covers removal section.

21

Replacing the “Return to Zero” Springs

1. Remove the top and side covers as directed in the covers removal section.

2. Using strong pliers firmly grasp the loop of the spring furthers away from the centre of the mechanism and pull it free from the spring retaining pillar.

Outer Spring Loop

Inner Spring Loop

3. Take both old springs out before installing the new ones.

4. Install new spring by fitting one loop over the spring retaining pillar closest to the centre of the mechanism. Using the strong pliers firmly grasp the other loop of the spring and stretch it over the spring retaining pillar furthest away from the centre of the mechanism.

5. Repeat for the second spring.

6. Apply a film of grease to the 4 loops and move the mechanism right and left a few times to ensure that the grease has made contact all around the loop.

7. Refit the covers as directed in the cover removal section.

Lubricating the Mechanism

1. Remove top covers as directed in the cover removal section.

2. Using a grease tube with a fine dispensing nozzle, point the nozzle into the following areas;

Inner Spring Pillars

Outer Spring Pillars Damper Slider

Centre Slider a. The centre composite slider – apply some grease to each sliding edge on the sides of the slider. b. The damper sliders - apply some grease to the top and bottom surfaces of each of the sliders. c. The spring pillars - apply some grease to each of the spring loops where they are in contact with the spring pillars. Manoeuvre the mechanism left and right to ensure that the grease has been applied all around the pillar.

3. Refit the covers as directed in the cover removal section.

22

Replacing the Centre Slider

1. Remove the top and side covers as directed in the covers removal section.

2. Using an 8mm Hex head, undo the bolt retaining this slider.

3. Remove the bolt taking care not to misplace the plastic washer behind the slider.

Centre Slider Damper Slider

4. Apply Loctite®222 to the bolt and fit through the new slider and reassemble. Tighten securely.

5. Apply some grease to each sliding edge on the sides of the slider.

6. Refit the covers as directed in the cover removal section.

Replacing the Damper Slider

1. Remove the top and side covers as directed in the covers removal section.

2. Using 10mm and 13mm wrenches, undo the nut from the damper pin at the moving end of the damper. Remove all components from damper pin noting their position for reassembly.

3. Replace the 2 damper sliders with the new ones and reassemble in the same order as they were disassembled. Tighten securely.

4. Apply some grease to each sliding edge on the sides of the slider.

5. Refit the covers as directed in the cover removal section.

23

E

QUIPMENT AND

T

ECHNICAL

I

NFORMATION

Please refer to Illustrations on Pages 30 to 32 for more information

X-Bike Frame Specifications

Pedal drive system

Pedals

Flywheel

Flywheel resistance

Felt flywheel resistant pads

Quick release height adjustment for handlebars

Quick release saddle height adjustment

Quick release saddle reach adjustment

Tilt Adjustable saddle

Metallic and lacquer protected paint system

Transport wheels on front base leg

Protective plastic caps on base legs.

Water bottle cage fittings

Chain tension adjustment

Non-slip rubber base for leveller feet

Elbow pads and arm rests.

X-Bars Specifications

Handlebar banking Angle to Bump Stops

Handlebar banking Angle with stops compressed

Maximum Horizontal Throw

Maximum Vertical Throw

Return to Zero

RTZ spring resistance

X-Bar Damping resistance adjustability

X-Bar Damping range

Max allowable force up on handlebars

Max allowable force down on handlebars

Max Force Fwd/Back on the handlebars

Maximum torque about head tube

General

Nominal height to centre of handlebars

Distance from centre of handlebars to Seat Post

Distance from centre of handlebars to Head Tube

Pitch of X-Bar movement to horizontal

Adaptor

Base Width

Mechanism Structure

Bearings

Bushings and Slider Materials

Handlebars

Bar Ends

Hand Grips

Fasteners

Freewheel drive pedals to Flywheel

Either Toe clip or SPD compatible clip less pedals

40 lb (18.2kg)

Multi-position SRAM Grip-shift™

75mm x 25mm (3” x 1”) Felt Pads to provide smooth pedal action

150mm (6”) vertical adjustment

340mm (13.5") saddle height adjustment

75mm (3") saddle reach adjustment

Yes

Yes

Yes

Yes

Yes

Yes

Optional

Optional

12°

14°

102mm

60.8mm

Yes

From 300N at centre to 775N at extremes

10Kg-f to 50Kg-f

7 positions

500N

1000N

500N

170 N-m

980mm

580mm nom. (+/- 100mm)

50mm nom.

72 Deg

Bespoke to suit a range of exercise spinner bikes

700mm wide base legs to provide excellent stability.

Die Cast Aluminium 356, machined aluminium and Hard Anodised

6061.

S45C and SCM430 Steel Chrome Plated

Igus Iglidur G and MC901

HANDLEBARS - 580mm to 680 max straight with 5 deg sweep with wall thickness 3.2mm at centre. Material 2014 Aluminium - Black anodise.

BAR ENDS - 28.6mm O/D as per SOS Boxer Design. Finish – Black

Anodised. Material 2014 Aluminium.

GRIPS - Length 11.5cm to 12cm. Colour Black. Finish ribbed

Zinc & Clear Passivate

24

Exploded View & Parts Identification

1 FRAME

2-1

2-2

FRONT BASE LEG

REAR BASE LEG

2-3

2-4

BASE LEG CAP

LEVELLER FEET SET

8-2

8-3

8-4

8-5

SEAT POST

SEAT QUICK RELEASE

HEIGHT ADJUSTER KNOB SET

SEAT POST STAND

9-2 GRIPSHIFTER

9-3 HANDLEBAR

9-4 BAR END

2-6 BASE LEG BOLT SET

4-2 KICK PLATE COVER

4-3 FENDER

4-4 FENDER BOLT SET

4-5 INNER CHAIN GUARD

4-6 RUBBERSEAL

4-7

4-8

EX CHAIN GUARD WITH SEAL

CHAIN GUARD BOLT SET

4-9 RUBBER GUARD

5-1 FLYWHEEL

5-2 FREE WHEEL

6-1 PADEL

6-3 BOTTOM BRACKET AXLE

6-4 CHAIN

9-6

9-7

9-9

9-10

9-11

POWER ADJUSTER

HEIGHT ADJUSTER KNOB SET

RESISTANCE PAD

RIGHT CHAIN ADJUST

LEFT CHAIN ADJUST

9-13 HANDLEBAR GRIP

25

X-Bars Exploded View

26

X-Bars Parts Identification Table

ID PART NUMBER

1 1283-BP6300-001

2 1282-AX1Y00-001

3 1282-FB01C0-001

4 1285-WS4000-001

5 1281-ODM500-001

6 1285-WS40A0-001

7 2110-BB04M1-001

8 212-4013C1

9 1282-AX1Z00-001

10 1282-FB2400-001

11 211-4616C8

12 2120-WASHER-009

13 1285-WS4100-001

14 1286-JP3500-001

15 2110-BB04M1-002

16 2110-BB04M1-005

17 1283-BP6400-001

18 1285-WS4300-001

19 1282-AX2C00-001

20 212-1016C1

21 212-4002-1

22 212-1004D7

23 2110-BB04M8-002

24 1282-AX2B00-001

25 1286-JP4300-001

26 1286-JP3600-001

27 1281-SPRING-009

28 1282-AX2A00-001

29 212-1004E5

30 212-1007-4

31 1283-BP6500-001

32 1285-WS4400-001

33 1282-FB2700-001

34 212-1058C1

35 212-4002D6

36 1282-AX2D00-001

37 1286-JP3700-001

38 1283-BP6600-001

39 1283-BP7100-001

40 1283-BP6700-001

41 1286-JP3800-001

42 2124-NUTM80-001

43 2110-BB04M6-002

44 212-4003D3

45 2120-WASHER-016

46 211-4BB04620C5

47 1276-XBARCV-003

48 1276-XBARCV-001

49 1276-XBARCV-002

50 1276-XBARCV-F01

51 1276-XBARCV-R01

52 1275-XBARW2-001

53 1275-XBARW1-001

54 1330-XBARHS-001

55 2110-BB1D00-001

56 211-4512B5

57 211-4820B3

58 2120-WASHER-017

59 212-4003D3

60 2115-BB05AH-009

QTY PART DESCRIPTION

1 BP63 147.2X46XT14 A6061-T6 ANOD

1 NHK ODM 500 DAMPER

1 BB04 M10X1.5X55 CRMO CP

1 BB04 M10X1.5X20 CRMO CP W/NYLOCK

1 BB04 M10X1.5X30/M5X20 CRMO CP W/NYLOCK

1 AX2C D20XM6XL34 SS41 CP/

1 56A1 6.3X13.5X3.5 FLAT UCP

15 M8 T1.5 FLAT OD16 STL

4 BB04 M8X1.25X85 CRMO CP

4 M8 SPRING WASHER CP

1 M6 CP T=6 (NYLON NUT)

1 AX2D D8XL45.1 SCM430 CP

1 BP67 A356 POL

3 BB04 M6X1.0X35 CP W/NYLOCK

5 M8 CP T=8 (NYLON NUT)

1 BB04 M6X1.0X20 CRMO CP

1 X-BAR COVER DOWN ABS P-YELLOW-012C

1 X-BAR COVER LEFT ABS P-GREY6C

1 X-BAR COVER RIGHT ABS P-GREY6C

1 X-BAR COVER FRONT ABS P-BLACK 3C2X

1 X-BAR COVER REAR ABS P-BLACK 3C2X

1 XBARW2 RUBBER PAD (X-BAR)

1 XBARW1 RIGHT PAD (X-BAR)

1 XBARHS H250 EXT99.9 CRMO CP

10 BB1D M4X0.7X10 STL W/WASHER (TWIST)

4 CP041A M5X0.8X12 STL WO/NYLOCK #3 TOOLS

4 BB04AH M8X1.25X20 STL WO/WS

4 M8 CP T=8 (NYLON NUT)

1 BB05AH M5X0.8X13 STL NYLON W/D14 WASHER

27

X-Bike

Indoor Performance Bike

F

EATURES

Structure

X-BIKE™ Indoor Performance Bike

o

High strength attractive tubular and elliptical steel X-bike™ Frame to provide an incredibly solid X-Bike™, strong enough to handle riders 300lbs (135kg). o

170 mm forged aluminium alloy crank arms with ISIS spline bottom bracket mount with 104/64, 4 bolt chain ring pattern for increased strength and reliability. Crank arms are interchangeable with all popular top quality crank arms except Shimano, so users can install their desired crank arm length. o

40lb (18.2kg) Balanced Cast Flywheel providing optimum pedalling inertia. o

Heavy gauge steel chain guard sufficiently rigid not to crack or bend. o

High strength elliptical tube 700mm wide base legs for total stability o

Stainless Steel hardware throughout mechanism to prevent corrosion or freezing. o

Maximum Dimensions (Not working): Lth 47.5 inches x Wth 28.5 inches x Hgt

39 inches o

Maximum User Weight Capacity: 300 lbs o

Commercial Warranty: Frame-5 Years, Parts-1 Years, Labor-6 Months, Wear

Items-6 Months (Country Dependent). The following parts list includes all wear parts that are protected under the warranty terms for a period of six-months past the date of X-Bike™ Indoor Performance Bike purchase:

• Damper Unit

• Damper Access Seal

• Height Adjustment Knobs

• Levelling Feet

• Flywheel Resistance Pads • PU Transport Wheels

• Centre Slider Block • Handlebar and Bar End Grips

• ‘Return to Zero’ Springs • Resistance Cable (Twist Grip to V-Brake)

• ‘Return to Zero’ Spring Pillars

All other part and components are protected under the warranty for twelve-months after date of purchase. The X-Bike™ Frame is protected under the warranty for fiveyears after date purchase.

X-BARS™ Handlebar System

o

The die cast aluminium X-Bars™ System is lightweight with high strength properties capable of withstanding 125lb-ft (170N-m) torque and 220lb (100kg) vertical load at the end of the handlebars. o

Authentic tamper proof “Trixter Enabled” identification holographic decal placed under the surface clear coat. o

Laser etched chrome plated square X-Bars™ adaptor to provide total lock against turning slip. o

X-Bars™ Bearings and Pivots constructed from high wear resistant Chrome Plated

Hardened Steel S45C and SCM430 materials. o

X-Bars™ Pivot Bushings and sliders constructed from maintenance free self lubricating composites paired up with slide runners made from high wearing hard anodised aluminium. o

27” (680mm) straight 2014 aluminium handlebars to cater for wide reach upper body workout. o

4-bolt clamp handlebar clamp to provide a very secure bar fitment. o

Boxer Bar ends o

Handlebar Grips – Hi grip rubber compound. o

Non-corrosive hardware fitted throughout mechanism to prevent corrosion.

28

Performance

o

True Cycle Geometry provided by the unique trapezoidal movement about a virtual cycling pivot point. o

Optimum low impact total body workout for the most efficient combined cross training to be found on an indoor cycle. o

Adjustable Hydraulic X-Bars™ Damper resistance to enhance various levels of upper body exercise. o

X-Bars™ ‘Return to Zero’ system providing up to 170lb (780N) pulling force in the mechanism to centralise the bars for regular spinning. o

Boxer Bar Ends which provide alternative upper body muscle group workouts and also provide a wrist rest for added rider comfort. o

High inertia drive system comprised of the 40lb (18.2kg) flywheel and direct drive gearing to simulate closely the feel of road riding. The sidewall resistance surface of the flywheel is machined to a perfectly even finish. Each wheel is finely balanced through a carefully programmed drilling operation to remove small quantities of distributed weight. The flywheel assembly is completed by fitting a high quality bearing. o

The transmission system is built to pro road bike standards. TH Power Pro 9900st

Bottom Bracket with ISIS spline drive, hollow, chrome molly steel spindle and sealed cartridge bearings. Standard 68mm bottom bracket width, 110 mm spindle length. The ISIS spline crank arm mounting system is superior to square tapered spindles because it is stronger, less likely to squeak or come lose and makes crank arm removal and installation faster and easier. o

3” x 1” (75mm x 25mm) felt pads to provide smooth pedal action and evenly distributed resistance. o

KMC S10 Stainless Steel chain (½ x 1/8” – 116 links) for low maintenance. o

Shimano SF-MX30 ½ x1/8, 16T freewheel and 52 tooth steel chain ring for added life. o

VP D68 aluminium alloy two sided pedals with chrome molly axles allowing a choice of SPD clip-less or half-toe clip.

Adjustability o

Fully indexed Grip-Shift™ providing a very efficient and easy to control adjustment to the flywheel resistance system for lower body elements. o

Fully adjustable X-Bars™ Damper Resistance System for upper body elements. o

A five-way, fully adjustable Rider Compartment accommodates users of nearly any size. Easily accessible and large one-hand quick release levers to make most the quick and easy adjustments. o

A self-aligning handlebar stem adjusts vertically up to 5” (130mm) with laser etched reference numbers on the handlebar stem aid when resetting your position. o

Quick release Saddle Reach adjustment up to 3.5” (90mm) via an extremely rigid extruded aluminium track and guide. Laser etched reference numbers on the sliding saddle base help you set your favorite position. o

Quick release Saddle Height adjustment laser etched “Indexed” seat positioning. An extra long, self-aligning seat post adjusts 15.75” (400 mm) to accommodate riders from below 5’ (1.5m) to 7’ (2.15M) tall. Laser etched reference marks on the seat post make resetting a favorite position easy. o

Saddle Tilt of 1.5” (38mm) fore/aft adjustment. o

Four leveller feet can be adjusted to compensate for irregular floor surfaces. o

Easily accessible Chain tension adjusting bolts to allow simple chain adjustment.

29

Safety

o

The X-Bars™ Handlebar System mechanism is enclosed to minimize the possibility of contact with moving parts. o

The Grip-Shift™ position on the handlebars allow the rider to maintain hands and grip in their assumed riding position for comfort, safety and non-interruption to the exercise routine. o

X-Bars™ System buffered end stop within the mechanism to provide smooth transition between left and right body movement ensuring no body injury. o

Hi-grip compound bar end covers to provide excellent hand grips at the outermost point of the handlebars. o

28” (700mm) wide base feet for added stability and safety have been fully tilt-table tested. o

Non-slip rubber cushions under the leveller feet to ensure no bike movement, even when bike is vigorously worked. o

Freewheel mechanism as per standard bicycle ensuring safer cycling with the absence of the inertia of a fixed flywheel. o

Double-sided pedals giving the 2 safe options of either toe clips or shoe clips.

Style & Comfort

o

Highly attractive and futuristic curved monocoque X-Bike™ Frame built from round and elliptical tubular steel. o

3 Tone, corrosion-resistant, zinc plated and powder coated metallic paint system with added protective and cosmetic enhancing clear lacquer coating system for unrivalled presentation and corrosion resistance. o

Integrated moving covers system displaying working geometry. o

Stylish front fender enhancing X-Bike’s™ look and keeping the corporate curved image throughout. o

Contoured highly cushioned seat – male and female for maximum comfort o

Rider controls are all conveniently located, simple to use and allow for maximum rider comfort and non-interrupted X-Biking™ Ride.

Protection

o

Paint system – as above with the added benefit of accepting all conventional cleaning materials. o

Sweat protection – All covers and general X-Bike features are specifically designed to channel sweat away from sensitive areas. o

Rubber seals provided at all points directly within the sweat zone ensuring no sweat ingress to the working mechanisms. o

Easily replaceable plastic covers on the handlebars and frame to protect your investment. o

Plastic kick-plate cover to protect the frame paintwork when mounting and dismounting the X-Bike™ Indoor Cycle. o

Front flywheel fender to channel sweat away from sensitive areas including moving parts and V-Brake system. o

V-Brake mechanism is fitted below the flywheel, well out of sweat zone for increased longevity and ease of maintenance. o

Chain guard to protect the moving drive parts. o

Full seam rubber seals around the chain guard to keep corrosive sweat away from moving parts inside. o

Protective plastic caps on 4 corners of base legs.

30

Service and Maintenance

o

Quick release covers for accessing dampers and springs when necessary. o

Chain cover with oiling point – exceptional ease of maintenance o

Easily accessible chain tensioning points.

Mobility & Storage

o

Two Large, 3”(75mm) diameter polyurethane transport wheels to absorb uneven floor surfaces and also to assist when moving X-Bike™ through door thresholds.

Polyurethane won’t scuff or mark floors either.

Additional Features & Options

o

Easily accessible water bottle holder o

New integrated water bottle holder holds 1 litre bottles of any shape o

SPD Compatibility o

Elbow pads and arm rests.

31

THANK YOU FOR PURCHASING AN X-BIKE

INDOOR PERFORMANCE BIKE

PLEASE TAKE A FEW MORE MINUTES TO READ OUR WARRANTY POLICY (PAGE 39), RECORD

AND RETAIN YOUR BIKE DATA (PAGE 40), AND COMPLETE THE WARRANTY REPLY CARD

(PAGE 41). THE CARD MUST BE RETURNED TO MATRIX FITNESS SYSTEMS WITHIN 30 DAYS OF

PURCHASE.

X-BIKE INDOOR PERFORMANCE BIKE WARRANTY CARD

(COPY FOR THE BUYER)

Frame Serial Number: ______________________________

Date Purchased: ______________________________

Bike Colour:

Name of Dealer:

______________________________

______________________________

X-BIKE INDOOR PERFORMANCE BIKE 6-MONTH WEAR PARTS

The following parts list includes all wear parts that are protected under the warranty terms for a period of six-months past the date of X-Bike™ Indoor Performance Bike purchase

• Damper Unit

• Damper Access Seal

• Height Adjustment Knobs

• Levelling Feet

• Flywheel Resistance Pads

• Centre Slider Block

• ‘Return to Zero’ Springs

• ‘Return to Zero’ Spring Pillars

• PU Transport Wheels

• Handlebar and Bar End Grips

• Resistance Cable (Twist Grip to V-Brake)

All other part and components are protected under the warranty for twelve-months after date of X-Bike™ Indoor

Performance Bike purchase.

The X-Bike™ Frame is protected under the warranty for five-years after date of X-Bike™ Indoor Performance Bike purchase.

32

L

IMITED

W

ARRANTY

On behalf of Matrix Fitness Systems, Trixter North America, Inc. and Trixter Europe Limited (“Trixter”) warrant the frame of each new indoor cycle to be free from defects in material and workmanship for a period of five years from the original date of purchase, as long as the original purchaser owns the cycle. All wear parts are warranted to be free from defects in material and workmanship for the original owner for a period of six months from the original date of purchase. The Wear Parts are listed in the Owner’s Manual and are available in advance on request. Reasonable wear and tear of the equipment is specifically excluded from any manufacturers warranty obligations. All other original components and all Matrix brand repair parts, replacement parts and accessories, except wear parts, are warranted to be free from defect in material or workmanship for a period of one year from the original date of purchase.

For a period of six months from the original date of purchase, as long as the original purchaser owns the cycle, Matrix will cover the labor cost of the warranty repair procedure. The limit of this element of warranty is covered by the individual procedure for any repair, which includes the limit on repair times based on the times taken by an experienced service engineer with the proper tools and training.

All potential warranty claims must be approved in advance of any work being carried out. Any claim for work already carried out without the appropriate advance approval will be automatically rejected.

MATRIX MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THAT OF THE EXPRESS

WARRANTIES STATED ABOVE.

Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

LIMITED REMEDY

Unless otherwise provided, the sole remedy under the above warranty or any implied warranty is limited to the replacement of defective parts with those of equal or greater value at the sole discretion of Matrix.

IN NO EVENT SHALL MATRIX BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON

CONTRACT, WARRANTY, NEGLIGENCE, PRODUCT LIABILITY, OR ANY OTHER THEORY, INCLUDING, WITHOUT

LIMITATION, PERSONAL INJURY DAMAGES, PROPERTY DAMAGE, OR ECONOMIC LOSSES.

EXCLUSIONS

THE ABOVE WARRANTY, OR ANY IMPLIED WARRANTY, DOES NOT COVER NORMAL WEAR AND TEAR, AND ALL WARRANTIES

ARE VOID IF THE INDOOR CYCLING EQUIPMENT IS USED FOR OTHER THAN NORMAL ACTIVITIES INCLUDING BUT NOT

LIMITED TO FAILURE TO FOLLOW THE OWNER’S MANUAL, FAILURE TO FOLLOW THE MAINTENANCE INSTRUCTIONS IN

THE OWNER’S MANUAL, USE UNSUPERVISED BY AN AUTHORISED X-BIKING™ INSTRUCTOR OR THE USE OF NON-

GENUINE SPARE PARTS RECOMMENDED BY MATRIX.

Some states do not allow the exclusion or limitation of consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state

.

WHAT YOU SHOULD DO

As soon as you experience any problems, note the serial number of the bike, locate your purchase receipt or other proof of date of purchase and your portion of the Warranty Registration Card and contact your Vendor or Distributor.

For up to date information on your Matrix Fitness Systems distribution network, please visit www.matrix-fitness.com

.

Or

Locate your purchase receipt or other proof of date of purchase, and then contact the Warranty/Service Department at:

Matrix Fitness Systems, Inc

1411 Broadway NE

Albuquergue, NM 87102 USA

Phone: 1.505.243.0560

Fax: 1.505.242.4725 www.martix-fitness.com

33

WARRANTY REPLY CARD

Thank you for purchasing this X-Bike™ Indoor Performance Bike. The owners’ manual contains all the necessary information for proper riding and maintenance of the bike. Before riding, you should read the manual and request that all users read the manual to ensure that the bike is set up and used correctly. You should pay particular attention to the cautionary notes on pages 4 and 5 of the owners manual to ensure that you or any user are in a healthy physical condition to ride the bike and that the bike is set up correctly for individual use. If you do not fully understand its operation, please contact your dealer. (See www.matrix-fitness.com

)

Frame Serial Number: ______________________ Date Purchased: ____________________________

Bike Colour: ______________________________ Dealer Name: ____________________________

Owner’s Name: ______________________________ Email Address

:_______________________

Street Address: ______________________________

______________________________

City: _____________________________________ Country:_______________________________

I have read the Owner’s Manual. I understand the health and safety cautionary notes contained therein and that I must post a copy of the X-Biking Safety Notice prominently in the place where the bikes are used. I understand the maintenance procedures, as per the Owner’s Manual, that are required to keep the X-Bike™ Performance Bike in a safe high performance condition and I understand that the X-Bike™ Limited Warranty is conditional on such maintenance being performed.

Signature:______________________________________ Date : ____/_____/_____

dd — mm — yy

From time to time we may wish to use the above information for further mailing or other commercial purposes. If you do not wish your details to be used, please tick the box.

To validate the warranty provisions regarding your X-Bike™ Indoor Performance Bike, you MUST fill in and return this

Warranty Card to your nearest Matrix office within 30 days of purchase:

Matrix Fitness Systems, Inc

1411 Broadway NE

Albuquergue, NM 87102 USA

Phone: 1.505.243.0560

Fax: 1.505.242.4725

www.martix-fitness.com

34

Dear new Matrix X-Bike™

Performance Indoor Bike Owner:

This is the backside of the Warranty Reply Card.

If you have not completed the Warranty Card –

Please DO SO NOW and MAIL IT IMMEDIATELY!

THANK YOU.

35

I

NDEX

Adjustment

Assembling the X-Bike Indoor Performance Bike

Basic Exercise Instructions

Bottom Bracket Bearings

Carton Contents

Centre slider replacement

Chain Guards

Chain lubrication

Chain replacement

Chain Tension Adjustment

10

7

12

24

6

28

20

16

21

16

Cleaning the X-Bike 15

Contents 3

Covers removal

Crank arm removal

26

23

Daily Maintenance

Damper performance

Damper replacement

Damper slider replacement

15

17

26

28

Dismounting the X-Bike

Exercise Guidelines

Exploded Views

Flywheel

13

12

30

20

Flywheel Resistance adjustment

Grip-shift replacement

15

22

Handlebar replacement 21

Pumping 12

Looseness 18

Maintenance 14

Mechanism lubrication

Monthly Maintenance

15

16

Mounting the X-Bike

Pedal Strap Adjustment

13

11

Pedalling 12

Pedalling resistance 10

Pedals replacement

Preventative maintenance

Product Features

Resistance Pads

Return to zero performance

Saddle replacement

Seat Adjustment

Setting up

17

25

9

7

24

15

34

19

Slider wear

Spare Parts

Springs replacement

Technical Specifications

18

30/32

27

29

Tools 14

Using the X-Bike 12

Weekly Maintenance

X-Bar resistance

15

13

36

37

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement