Ryobi RY80940B 3,100 PSI 2.5 GPM Honda Gas Pressure Washer with Idle Down Instructions / Assembly

RY80940 QUICK REFERENCE GUIDE
WARNING:
This Quick Reference Guide is not a substitute for reading the operator’s manual. To reduce the risk of injury or death, user must read and understand operator’s manual before using this product. All page references refer to
the operator’s manual.
FIRST TIME ASSEMBLY
1
6
Raise the handle (see page 8).
STARTING THE UNIT (COLD START)
Connect the high pressure hose to the pump
(see page 9).
1
5
Add fuel (see page 10).
USING DETERGENT
Pull starter grip and rope to start (see page 11).
1
Pour pressure washer
­detergent in detergent tank
(see page 13).
DO NOT USE E15 OR E85 FUEL IN THIS UNIT.
IT IS A VIOLATION OF FEDERAL LAW AND WILL
DAMAGE THE UNIT AND VOID YOUR WARRANTY.
SO
AP
2
Install nozzle and rotate
selector to blue
or blue
setting (see page 13).
3
Squeeze trigger and wait
­approx. 5 seconds for soap
(see page 13).
DETERGENT
5S
Completely uncoil and straighten high pressure
hose to prevent kinks.
Install the trigger handle holder, spray wand
holder, and hose storage (see page 8).
7
Connect your garden hose to the pressure washer
(see page 9).
Use of soap nozzle will activate detergent injector at a
20:1 dilution ratio.
SO
AP
2
• Will damage your pump
• Will void your warranty
WARNING! Never use bleach or solvent-based detergent.
This is a 4-cycle engine. Do not mix fuel and
lubricant ­together.
Completely uncoil garden hose or remove
­completely from reel to prevent kinks.
6
NOZZLE SELECTION GUIDE
Allow engine to run for several seconds, then
move choke to RUN position (see page 11).
Add fuel stabilizer every time you fuel the
machine.
• Will damage plants/shrubs
Use the chart below to determine the correct nozzle for your job.
Turn water faucet on fully.
SO
AP
2
Turn the fuel valve to ON (see page 11).
CHOKE LEVER
(RUN)
FUEL
VALVE ON
Make sure there are no leaks.
With no nozzle installed, squeeze the trigger
to relieve air pressure. Hold the trigger until a
steady stream of water appears.
Assemble the trigger handle (see page 8).
Add entire bottle of lubricant provided to the pressure washer (see page 10).
5S
SO
AP
8
SO
AP
3
SO
AP
ABRASIVE
3
CHOKE LEVER (START)
Connect the high pressure hose to the trigger
handle (see page 9).
1
Siding, Gutters, House
Fencing, Deck, Patio
Pull starter grip and rope to start (see page 11).
Lawn Equipment, Boat, RV
SO
AP
(NO SOAP WHEN USING
THESE NOZZLES)
(FOR SOAP OR
GENTLE RINSE)
0º
25º
40º









Long Range Short Range








SO
AP
 Recommended Nozzle  Use With Caution for Certain Applications
4
Turn the fuel valve to OFF before adding
lubricant.
BEFORE STORING THE UNIT
Put on/off switch in ON position (see page 11).
1
Set unit on flat surface so engine is level.
Remove dipstick, wipe clean, put back in hole
(but don’t screw in) and check lubricant level.
ON/OFF
SWITCH
(ON)
Add Pump Protector to the unit after each use and before storing. This will significantly improve pump
life (see page 15).
To order Pump Protector, call customer service at 1-800-860-4050.
To add, follow the instructions provided by the Pump Protector manufacturer.
PUMP
PROTECTOR
SO
AP
DO NOT OVERTILT THE UNIT!
If you need more assistance, visit our website at
www.ryobitools.com or call us at 1-800-860-4050.
SO
AP
4
RESTARTING THE UNIT
(HOT RESTART)
LOW ­PRESSURE
GENTLE
Concrete, Brick, Masonry
Put choke lever in START position (see page 11).
HIGH PRESSURE
If the engine does not start:
• check for enough fuel;
• may need to adjust choke position;
• try starting again.
990000250
10-4-12 (REV:01)