Tribute™
Tribute™
Child Restraint System
Owner’s Manual
Keep for future use.
Rear-facing
2.3 to 18 kg
(5 to 40 lbs)
48 to 94cm
(19 to 37 in.)
Forward-facing
10 to 18 kg
(22 to 40 lbs)
71 to 102 cm
(28 to 40 in.)
Para instrucciones en Español,
llamar al: 1-800-233-5921.
WARNING:
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
© 2014 Evenflo Company, Inc.
25706660
8/14
More children are killed every year as passengers
in car crashes than by any other type of injury. To
reduce the risk of SERIOUS INJURY or DEATH, read this
owner’s manual and your vehicle owner’s manual before installing and using this child restraint. Using a child restraint makes a
big difference. By properly using this child restraint and following
these instructions (and the instructions that accompany your vehicle), you will greatly reduce the risk of serious injury or death to
your child from a crash. Do not be misled by the commonly used
term “safety seat;” no restraint system can prevent all injuries in all
crashes. Many properly restrained adults and children are injured in
motor vehicle crashes, including relatively minor crashes. A properly
used child restraint is the best way to minimize injuries to your child
and to increase the chances for your child’s survival in most crashes.
Table of Contents
Warnings................................................................... 2
Safe Practices............................................................. 9
Recall Information for U.S. Customers..................... 10
Public Notice for Canadian Customers.................... 10
Motor Vehicle/Aircraft Usage................................... 10
Storing Your Instructions......................................... 11
Symbol Legend....................................................... 11
Visual Glossary......................................................... 12
Securing Your Child in the Child Restraint ............... 14
Removing Your Child from the Child Restraint ........ 15
Using the Tribute™ Rear-facing......................16
Positioning the Recline Stand................................ 18
Installing with Lower Anchor Connectors ............. 19
Installing with a Seat Belt...................................... 23
Using the Tribute™ Forward-facing...............26
Positioning the Recline Stand................................ 28
Installing with the Lower Anchor Connectors........ 29
Installing with a Seat Belt...................................... 33
Positioning the Harness Strap.................................. 37
Adjusting the Crotch Strap...................................... 39
Adjusting the Harness Strap..................................... 39
Removing the Tether Strap...................................... 40
Removing the Lower Anchor Connectors ................ 41
Installing the Accessories.......................................... 42
Care and Cleaning .................................................. 43
Securing Your Child Restraint in Aircraft .................. 44
Installing Child Restraint Rear-Facing in Aircraft ....... 44
Installing Child Restraint Forward-Facing in Aircraft .47
Replacement Parts................................................... 49
Limited Warranty..................................................... 50
U.S. REGULATORY NOTICE
This child restraint meets all applicable requirements of
Federal Motor Vehicle Safety Standard 213.
CANADIAN REGULATORY NOTICE
(Model numbers ending in “C.”)
This child restraint meets all applicable requirements of
Canadian Motor Vehicle Safety Standards CMVSS 213
and 213.1.
Child Requirements
• No restraint can guarantee absolute protection from
injury in every crash.
• This child restraint is designed for use by children in
rear-facing and forward-facing positions. To use this
child restraint properly, children MUST meet weight/
size specifications as follows:
For Rear-facing Use
• The child weighs 2.3 – 18 kg (5 – 40 lbs)
• The child is 48 – 94 cm (19 – 37 inches) AND the top
of child’s head is at least 25 mm (1 in.) below the top
of the child restraint seat back.
The American Academy of Pediatrics recommends
that children ride in the rear-facing position to
the highest weight or height allowed by the child
restraint.
For Forward-facing Use
• The child weighs 10 – 18 kg (22 – 40 lbs)
• The child is 71 to 102 cm (28 to 40 inches) AND the
tops of the childs ears are below the top of the child
restraint seat back.
•Child is one year old or older
Note: Once your child exceeds 18 kg (40 lbs) OR
is taller than 102 cm (40 in.), they can no longer
safely use this child restraint, and you should
consider using a booster seat.
1
WARNING
Air Bag Warnings
General Warnings
Rear-facing and Forward-facing Use
Rear-facing and Forward-facing Use
• Failure to follow installation instructions can result in
the child striking the vehicle’s interior during a sudden
stop or crash. Serious injury or death may result.
These instructions and the instructions in your vehicle
owner’s manual must be followed carefully. If there is a
conflict between the two, the vehicle owner’s manual
regarding child restraint installation must be followed.
• NEVER leave child unattended.
• Children have STRANGLED in loose or partially
buckled harness straps. Fully restrain the child.
• DO NOT use this child restraint in the front seat of a
vehicle equipped with an air bag, unless the air bag
has been deactivated. Interaction between a rearfacing restraint and air bags may cause serious injury
or death. Air bags may cause serious injury or death to
children 12 and under.
If your vehicle has an air bag, refer to your vehicle
owner’s manual for child restraint installation.
• If the rear seat of your vehicle is equipped with side
air bags, refer to the following information for proper
usage.
Vehicles built prior to the 2002 model year:
DO NOT use this restraint in a vehicle seating position
equipped with a side air bag unless authorized by the
vehicle manufacturer.
Model year 2002 and newer vehicles:
Refer to your vehicle owner’s manual before placing this
restraint in a seating position equipped with a side air bag.
DO NOT place any objects between the restraint and
the side air bag, as an expanding air bag may cause
the items to strike the child.
WARNING
Children have STRANGLED
in loose or partially buckled
harness straps. Fully restrain
the child.
• DO NOT use child restraint if it is damaged, broken,
or missing parts.
• DO NOT use this restraint if it has been involved in a
crash. It must be replaced.
Location Warnings
Rear-facing, Forward-facing Use
• ALWAYS read and follow exactly the instructions
that accompany your vehicle and child restraint.
• According to statistics, children are safer when
properly restrained in a rear seating position than in
the front seating position. Generally, the center rear
position is safest and should be used if available.
• Some child restraints do not fit all vehicles or all seating
locations. There are many thousands of combinations
of vehicle makes, models, child restraint configurations,
vehicle seat belt designs, and seat cushion shapes. The
easiest way to determine whether your child restraint is
suitable for a particular seating position is to check for a
tight installation.
2
3
Important Information
WARNING
WARNING
Location Warnings – cont.
Rear-facing Position Warnings
Rear-facing and Forward-facing Use
If the child restraint cannot be properly installed, DO
NOT use the child restraint. Consult vehicle owner’s
manual, try a different seating location, or call Evenflo for
further assistance.
• ONLY use this child restraint on forward-facing
vehicle seats. DO NOT use this restraint with
vehicle seats that face the rear or side.
• ONLY use this child restraint on vehicle seats with backs
that lock into place.
Rear-facing Use Only
• DO NOT use the tether strap when the child restraint
is in the rear-facing position.
• The headrest on the vehicle seat that the child faces
when sitting in the rear-facing mode should be placed
in the lowest position. The vehicle seat back that the
child faces must be fully padded and free of any hard
objects.
Premature Infants
Forward-facing Use Only
•If your child weighs more than 18 kg (40 lbs) or their
shoulders are above the highest harness level, you MUST
discontinue using this child restraint as it may no longer
adequately protect your child.
•DO NOT use the lowest set of harness slots forward-facing.
The harness will not properly restrain the child during a
crash.
• Adjust, or remove, the vehicle headrest, in the seat
where the child restraint is to be installed, so
that the back of the child restraint rests against the
vehicle seat back.
• The headrest on the vehicle seat in front of the child
should be put in its lowest position. The vehicle seat
back that the child faces must be fully padded and
free of any hard objects.
Rear-facing and Forward-facing Use
• DO NOT use this or any child restraint with a
premature infant until after consulting your doctor.
Premature infants may have difficulty breathing when
in a seated or semi-reclined position. Using additional
padding or pillows behind the infant’s head or failing
to properly recline the child restraint could increase the
child’s risk of serious injury or death.
Rear-facing Position Warnings
Rear-facing Use Only
• DO NOT use this child restraint rear-facing in a vehicle
equipped with lap belts that only lock during a sudden stop
or crash (emergency locking retractor – ELR). You must use a
seating location with a locking seat belt. Check your vehicle
owner’s manual to see if you have lap belts with ELRs.
• When using this restraint rear-facing, DO NOT loosen
the vehicle seat belt to provide more leg room, as this
will prevent the child restraint from protecting the child.
• DO NOT use the highest set of harness slots rearfacing. The harness will not properly restrain the child
during a crash.
• Fold-down armrests could pose a hazard to a rearfacing child in certain types of collisions. Consult your
vehicle owner’s manual before installing any rearfacing child restraint in front of a fold-down armrest.
• NEVER turn a child restraint forward-facing with an
infant who weighs less than 10 kg (22 lbs) or is less
than one year of age. Crash forces may cause
serious injury or death.
4
Forward-facing Position Warnings
5
Important Information
WARNING
WARNING
Seat Belt Warnings
LATCH Warnings
Rear-facing and Forward-facing Use
Rear-facing and Forward-facing Use
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) side to side or front to back at either
the rear-facing or forward-facing belt path on the
child restraint. Serious injury or death may result from
poor installation. If you cannot tightly secure the child
restraint, try again or move it to another location.
• DO NOT use this child restraint in a seating position
with door-mounted seat belts.
• DO NOT use this child restraint in a vehicle with seat
belts that automatically move along the vehicle frame
when the door is opened. These seat belts will not hold
a child restraint properly.
• If the vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect the child
in a crash.
• DO NOT allow the vehicle seat belt release button to
touch the child restraint. Accidental contact may cause
the seat belt to release. If necessary, turn the seat belt
release button away from the child restraint or move
the child restraint to a different location.
• Failure to adjust the harness or vehicle seat belts
snugly around the child may result in the child striking
the vehicle’s interior during a sudden stop or crash.
Serious injury or death may occur.
• The LATCH system is intended to be used ONLY as
described in these instructions. Serious injury or death
may result from misuse. LATCH (Lower Anchors and
Tethers for CHildren) is a system for attaching the
child restraint to your vehicle seat. It can be used in
place of the seat belts in vehicles with vehicle lower
anchor bars. Refer to your vehicle owner’s manual for
the locations of the vehicle lower anchor bars. Note:
Your vehicle owner’s manual may refer to this system
as “Universal Anchorage System,” “Lower Universal
Anchorage System,”or ”ISOFIX.”
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of the
child restraint and LATCH. If there is a discrepancy,
follow your vehicle owner’s manual.
• ONLY use for securing child restraint to vehicle lower
anchor bars.
• NEVER attach two lower anchor connectors to one
vehicle lower anchor bar.
• NEVER use the vehicle seat belts when using the
Lower anchor connector assembly. Using both together
can cause slack in a sudden stop or crash.
•To avoid strangulation, you must store the unused LATCH
harness, with all slack removed, in the storage area on
the back of the seat. Roll or fold the excess LATCH strap
and secure with a rubber band to prevent serious injury
to vehicle occupants.
• ALWAYS be sure that the lower anchor connectors are
attached to the vehicle lower anchor bars by pulling
hard on the lower anchor connectors. If they are not
attached, the lower anchor connector assembly will
not secure your child restraint. Serious injury or death
may result.
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) side to side or front to back at either
the rear-facing or forward-facing belt path on the
child restraint. Serious injury or death may result from
poor installation. If you cannot tightly secure the child
restraint, try again or move it to another location.
6
7
Important Information
WARNING
WARNING
Additional Warnings– cont.
Forward-facing Use Only
• In cold weather, DO NOT dress the child in bulky
clothing like snowsuits if the child is riding in a child
restraint. Bulky coats/snowsuits make it difficult to
properly tighten the harness to the child, which may
allow the child to be ejected from the restraint during
a crash. If necessary, place a blanket over the
harnessed child without interfering with the child
restraint harness system.
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess or unused tether strap and secure with
a rubber band. Attach the tether hook to the storage
clip when not in use (p. 13). This will keep an unused
tether from hitting someone during a crash.
Additional Warnings
Rear-facing and Forward-facing Use
• In hot or sunny weather, ALWAYS check the areas of
the child restraint that may contact your child (e.g.,
buckle, buckle tongues, etc.) for hot areas before
placing him/her into the child restraint. The child
could be burned. Cover the child restraint with a light
colored blanket when you leave the vehicle.
• This child restraint must be securely fastened to the
vehicle, even when unoccupied, using the vehicle
seat belts or lower anchor connectors. An unsecured
child restraint may injure someone if a crash occurs.
• DO NOT use the cup holder to store cans or hard
cups. Only for use with soft cups (such as styrofoam
or paper).
• DO NOT place any cups that contain hot liquids
in the cup holder.
• DO NOT attach additional padding, toys, or other
devices not made by Evenflo or described in these
instructions for the child restraint. Items not tested
with the child restraint could injure the child.
Additional pads or pillows may interfere with the
function of the harness system, or cause breathing
problems if the child’s head falls forward, increasing
the risk of serious injury or death.
• Failure to follow installation instructions could result
in serious injury or death. These instructions and the
instructions in your vehicle owner’s manual must be
followed carefully. If there is a conflict between the
two, the vehicle owner’s manual regarding child
restraint installation must be followed.
8
Safe Practices
• Everyone rides buckled up or the vehicle does
not go. Make no exceptions for adults or children. If
someone unbuckles, stop the vehicle. Being firm and
consistent from the start will mean fewer discipline
problems as children get older. An unrestrained person
can be thrown into and injure other passengers.
• Many safety advocates and healthcare professionals
recommend that children ride rear-facing for as long
as possible. See limitations recommended on
rear-facing use on the inside front cover.
• NEVER try to tend to a crying baby’s needs while
driving. NEVER take a baby out of a child restraint for
comforting while the vehicle is moving.
• DO NOT allow a child in a vehicle to have objects
such as lollipops or ice cream on a stick. The object
can injure the child if the vehicle swerves or hits a
bump.
• DO NOT feed an infant who is riding in a child
restraint.
• Put sharp or heavy items in the trunk. Anything loose
can be deadly in a crash.
9
Important Information
WARNING
Tether Strap Warnings
Storing Your Instructions
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a
recall. Send your name, address, e-mail address, the
restraint’s model number, and manufacturing date
to:
Evenflo Company, Inc., 1801 Commerce Dr.,
Piqua, OH 45356, or call 1-800-233-5921.
You may also register on-line at:
www.evenflo.com/registercarseat
• For recall information call the U.S. Government’s
Vehicle Safety Hotline at 1-888-327-4236
(TTY:1-800-424-9153), or go to http://www.NHTSA.gov
After thoroughly
reading and
following these
instructions,
store them
in the clips on
either side
of your child
restraint.
Important Information
Recall Information for U.S. Customers
Public Notice for Canadian Customers
• To register your child restraint, return your registration
card, call 1-937-773-3971, or register on line at
www.evenflo.com/registercarseatcanada
• For recall information, call Transport Canada at
1-800-333-0510 (1-613-993-9851 in Ottawa
region) or Evenflo at 1-937-773-3971.
Symphony 65
™
Child Restraint System
Motor Vehicle/Aircraft Usage
When used with the internal
harness and properly installed
pursuant to these instructions,
this restraint is certified for use only
in passenger and multi-purpose
Check with
passenger motor vehicles, buses,
your airline before
and trucks equipped with Type I
departure to make sure
or II seat belts and in aircraft.
Tip
ip!!
Airplane installation is the same
as Type I vehicle installation. Turn
the top of the airplane seat belt
buckle away from the restraint for
easy release and removal.
this restraint meets
their requirements.
Refer to pages 44 to 48 for instructions on installing your
child restraint in aircraft.
10
For future reference, record the model number of your
child
Owner’s
Manual
restraint AND the date of manufacture below.
Rear-facing
Keep for future use.
2.3 to 18 kg
(5 to 40 lbs)
Model Number:
48 to 94 cm
(19 to 37 in.)
Forward-facing
10 to 29.4 kg
(22 to 65 lbs)
Date of Manufacture:
71 to 127 cm
(28 to 50 in.)
Booster
18 to 49.8 kg
(40 to 110 lbs)
110 to 145 cm
(43.3 to 57 in.)
Para instrucciones en Español,
llamar al: 1-800-233-5921.
Symbol Legend
WARNING:
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
© 2013 Evenflo Company, Inc.
Airbag Symbol – Alerts you to important
information about airbag safety.
LATCH Symbol – Alerts you to important
information about LATCH safety.
Tether Anchor Symbol – Alerts you to
important information about tether anchor safety.
11
25700938
2
Visual Glossary
Your vehicle components may be significantly different than
pictured. Consult your owner’s manual to help you identify
your vehicle components.
Fold-down Armrest
Consult your vehicle’s owners manual.
Tether Anchors
Forward-facing
only
Rear
Headrests
Important Information
Visual Glossary
Front Seat Lap
and Shoulder Belts
Front
Headrests
Back Seat
Belt Buckles
10
Back Seat
Retractor
4
30
20
12
0
Center Lap
Belt
A
IR
B
A
G
Lap/Shoulder Belt
Important
Vehicle
Lower
Anchor
Bars
Seat Crease
Front Seat Retractor
IMPORTANT: If your vehicle has side air bags, please refer to the
warnings on page 2.
Front View
Top Harness Position
Forward-facing
ONLY
Middle Two
Harness Positions
ForwardOR Rear-facing
Chest Clip
Lowest Harness
Position
Rear-facing ONLY
Harness Straps
Crotch Strap
Buckle
Consult your vehicle
owner’s manual to determine
proper placement of child restraint
in your vehicle and familiarize
yourself with your vehicle’s
components.
Back View
Top Harness Position
Forward-facing
ONLY
Instruction
Storage Area
Middle Two
Harness Positions
ForwardOR Rear-facing
Tether Strap
and Hook
Harness Straps
Lower Anchor
Connector
Assembly
Splitter Plate
Lowest Harness
Position
Rear-facing ONLY
Seat Pad
Harness Release
Button
Harness Adjuster
Strap
12
Recline Stand
13
Removing Your Child from the
Child Restraint
1
Using the 2-piece Chest Clip
A
C
Place baby in the child restraint. The baby’s back and
bottom should be flat against the restraint. If there is a
gap, the baby will not be comfortable.
Using the 2-piece Chest Clip
B
Push the release button A Press the red buckle
release B, and remove
and pull the chest clip
both buckle tongues C.
apart.
2
Insert the buckle tongues into
Slide each harness strap
over the child’s shoulders. the buckle. Pull up on the
harness strap to ensure the
buckle tongues are engaged.
3
A
Align the two sides of the The harness straps must be
chest clip A and snap
snug against the child. A snug
them together. The chest strap should not allow any slack.
clip must be positioned It lies in a relatively straight line
at armpit level.
without sagging. It does not
press on the child’s flesh or push
the child’s body into an unnatural
position. Check the harness
straps near the shoulders for
slack. You should NOT be able
to pinch the harness (see illustration).
Adjust as needed.
14
15
Important Information
Securing Your Child in the Child
Restraint
Child Requirements for Rear-facing:
Rear-facing Installation Checklist
1.Secure child restraint to the vehicle seat.
• Recline Stand is flipped to the Recline position
(page 18).
• Weight: 2.3 to 18 kg (5 to 40 lbs)
• Height: 48 to 94 cm (19 to 37 in.). AND the top of
the child’s head is least 25 mm (1 in.) below the top of
the child restraint seat back.
25 mm (1 inch)
or more
• Install with Lower Anchor Connector Assembly
(page 19) or the vehicle seat belt (page 23).
• Towel rolled up and placed beneath the base, if
necessary (page 18).
• Install locking clip, if necessary (page 24).
2.Set the child in the child restraint.
Top of head is at least 25 mm (1 inch) below the
top of the child restraint seat back.
3.Make necessary adjustments.
• Harness straps are snug against the child’s
shoulders, with no slack (page 14).
• Crotch strap is snug against the child (page 39).
4.Fasten the buckle. Refer to page 14.
5.Position and connect chest clip.
Chest clip MUST be at armpit level (page 14).
6.Check your work.
• Recline Stand is flipped to the Recline position
(page 18).
• To properly secure this child restraint it MUST
NOT move more than 25 mm (1 inch) from side
to side or front to back at the rear-facing belt
path (pages 22 and 25).
• The child’s back and bottom are flat against the
back and bottom surfaces of the child restraint.
• Shoulder harness straps MUST start at or below
shoulder height, using the strap slots closest to
your child’s shoulders (page 37).
• Buckle tongues are fully engaged.
• The level arrow is level with ground (page 18).
Note: When in rear-facing position, bottom of child
restraint MUST be entirely on vehicle seat.
16
17
Rear-facing
Using the Tribute™
Rear-facing
Positioning the Recline Stand for
Rear-facing Use
Lift the child restraint and
flip the recline stand A
toward the front, as
shown, to the Recline
position.
Installing the Child Restraint
Rear-facing with
Lower Anchor Connectors
LATCH is a system for attaching the child restraint to
your vehicle seat. It is to be used in place of your
vehicle’s seat belts, and can be used in vehicles with
LATCH anchors. Your vehicle owner’s manual may refer
to this system as ISOFIX, Universal Anchorage System
(UAS), or Lower Universal Anchorage System.
Rear-facing Recline
Level Arrow
Arrow MUST be level
with ground when used
Rear-Facing
La flèche DOIT être à niveau
avec le sol lors de l’utilisation
en orientation face à l’arrière
ARRIÈRE DU VÉHICULE
REAR OF VEHICLE
B
The child restraint MUST be in the Recline position for
rear-facing use. Child MUST weigh 2.3 – 18 kg (5 – 40 lbs).
If the level arrow is not parallel to the ground, use a
tightly rolled towel or small blanket B beneath the
front edge of the child restraint.
You need to provide enough recline for an infant’s
head to lie back comfortably.
IMPORTANT: Infants may have difficulty breathing
when in a sitting position. Make sure they recline enough
for their head to lie back comfortably and safely. Failure
to properly recline the child restraint could increase the
child’s risk of serious injury or death.
18
• ONLY use for securing child restraint to lower anchor
bars.
• ALWAYS read and follow exactly the instructions
which accompany your vehicle and child restraint.
• NEVER attach two hooks to one vehicle lower anchor
bar.
• DO NOT use the vehicle seat belts to install a child
restraint when using the Lower Anchor Connector
Assembly.
• This Lower Anchor Connector Assembly is intended to
be used ONLY as described in these instructions.
Serious injury or death may result from misuse.
• ALWAYS be sure that the Lower Anchor Connector
hook is fully engaged onto the Vehicle Lower Anchor
Bar by pulling hard on the Lower Anchor Connector
strap. If it is not totally engaged, the Lower Anchor
Connector Assembly will not secure your child
restraint. Serious injury or death may result.
• To avoid a strangulation hazard, you MUST store
the unused lower anchor connector assembly, with all
slack removed, in storage area on the back of the seat.
Roll or fold excess lower anchor connector strap and
secure with a rubber band to prevent serious injury to
vehicle occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of child
restraints and LATCH. If there is a discrepancy, follow
your vehicle owner’s manual.
19
Rear-facing
WARNING
A
WARNING
NEVER turn a child restraint
forward-facing with an infant
weighing less than 10 kg (22 lbs)
or less than one year of age.
Crash forces may cause serious
injury or death.
2
D
Pull the seat pad off of the
front of the child restraint.
Route the Lower Anchor
Connector strap C
and hook through the
rear-facing belt paths D.
C
E
Infants MUST always ride facing the rear of the
vehicle. The back of the child restraint supports and
protects the baby and absorbs crash forces.
Adjust the child restraint to the Recline position (p. 18).
Place the child restraint in your vehicle rear-facing.
1
WARNING
DO NOT use the upper harness slots rear-facing. The
harness may not properly restrain the child during a crash.
E
D
C
When the crotch strap E
is in the front slot, route
Lower Anchor Connector
strap C behind the crotch
strap, as shown.
4
When the crotch strap E
is in the rear slot, route
Lower Anchor Connector
strap C in front of the
crotch strap, as shown.
F
F
G
A
Make sure that the harness
straps are in one of the three
lower harness positions A.
The harness straps must start
at or below shoulder height,
using the strap slots closest
to your child’s shoulders B,
as shown.
G
Refer to your vehicle owner’s manual to locate the
lower anchor bars on your vehicle seat. Attach the
right hook F to the right anchor bar G, and the left
hook to the left anchor bar. DOUBLE CHECK that the
Lower Anchor Connector hook is fully engaged by
pulling hard on the Lower Anchor Connector Assembly
Strap.
B
20
21
Rear-facing
3
Installing the Child Restraint
Rear-facing with a Seat Belt
5
WARNING
Infants MUST always ride
facing the rear of the
vehicle. The back of the
child restraint supports
and protects the baby and
absorbs crash forces.
D
Using your full weight, push the child restraint firmly
into the vehicle seat while pulling up on the lower
anchor connector assembly strap to tighten.
The lower anchor connector assembly strap must be
as tight as possible.
If you can move the child restraint more than 25 mm
(1 inch) side to side or front to back at the rear-facing
belt path D, the lower anchor connector assembly strap
is not tight enough. You will need to try again, find
another location for your child restraint, or install with
the vehicle seat belt (page 23).
To remove the lower anchor connector assembly strap,
go to page 41.
Adjust the child restraint to the Recline position (p. 18).
Place the child restraint in your vehicle rear-facing.
1
WARNING
DO NOT use the upper harness slots rear-facing. The harness
may not properly restrain the child during a crash.
A
Make sure that the harness
straps are in one of the three
lower harness positions A.
The harness straps must start
at or below shoulder height,
using the strap slots closest
to your child’s shoulders B,
as shown.
WARNING
DO NOT use this child restraint if it moves more than
25 mm (1 in.) side-to-side or front to back at the rearfacing belt path. Serious injury or death may result from
poor installation. If you can not tightly secure the child
restraint, try again or move it to another location, or
install with the vehicle seat belt.
22
B
23
Rear-facing
NEVER turn a child restraint
forward-facing with an infant
weighing less than 10 kg (22 lbs)
or less than one year of age.
Crash forces may cause serious
injury or death.
Lap & Shoulder
Belt Combination
Lap Belt Only
C
Ä
D
Ä
Ä
D
C
5
Pull the seat pad off of the front of the child restraint.
Route the vehicle seat belt C through the rear-facing
belt path D, continue through the opposite opening
of the child restraint. Fasten the vehicle seat belt, as
shown, depending on your type of seat belt.
C
D
Ä
3
C
E
C
E
When the crotch strap E
is in the front slot, route
seat belt C behind the
crotch strap, as shown.
4
When the crotch strap E
is in the rear slot, route
seat belt C in front of
the crotch strap, as shown.
Install Locking Clip,
if necessary.
If your vehicle was built prior to
model year 1996, and has either
a lap belt or lap/shoulder belt that is
equipped with an emergency locking
retractor (ELR), you MUST use a
Locking Clip. Check your vehicle
owner’s manual to identify which
vehicle belt system is in your vehicle.
If your vehicle is model year 1996 or newer, it likely
has a vehicle belt system that can be locked when
tightened, and will not require use of a Locking Clip.
Consult your vehicle owner’s manual before
installing a locking clip.
If your vehicle requires a Locking Clip, please call
ParentLink (see back cover) to obtain a Locking Clip
and instructions on how to install and use it.
Locking Clip
installed
properly.
13 mm
(0.5 inch)
WARNING
• Remove Locking Clip from vehicle seat belt when not used
with a child restraint, or the vehicle seat belt will not properly
restrain an adult or child. Serious injury could occur.
24
WARNING
• If vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect your
child in a crash.
• DO NOT use this child restraint if it moves more than
25 mm (1 in.) side to side or front to back at the rearfacing belt path. Serious injury or death may result
from poor installation. If you can not tightly secure
the child restraint, try again or move it to another
location, or install with the lower anchor connector
assembly.
The seat belt must be as tight as possible.
Put your full weight into the child restraint as you
tighten the seat belt C.
Check your work.
Make certain the belts are tight. If you can move
the child restraint more than 25 mm (1 inch) side to
side or front to back at the rear-facing belt path D,
the vehicle belt is not tight enough. If you have not
tightly secured the child restraint, try again, move it
to another location, or install with the lower anchor
connector assembly (p. 19).
25
Rear-facing
2
Using the Tribute™
Forward-facing
Child Requirements for Forward-facing:
• Weight: 10 to 18 kg (22 to 40 lbs)
• Height: 71 to 102 cm (28 to 40 in.) AND the tops
of the child’s ears are below the top of the child
restraint seat back.
• Age: At least one year of age.
Forward-facing Installation Checklist
WARNING
If your child weighs more than 18 kg (40 lbs) or their
shoulders are above the highest harness level, you MUST
discontinue use or the child restraint will not protect your
child.
1.Secure child restraint to the vehicle seat.
• Recline Stand is flipped to the Upright position
(page 28).
• Install with the Lower Anchors Connector
Assembly (page 29) or
the vehicle seat belt (page 33) and tether
strap (page 32/36).
• Install locking clip, if necessary (page 34).
Tether Strap
2.Set the child in the child restraint.
The top of the child’s ears MUST be below the top
of the child restraint seat back.
3.Make necessary adjustments.
• Harness straps are snug against the child’s
Chest clip MUST be at armpit level (page 14).
6.Check your work.
• Recline Stand is flipped to the Upright position
(page 28).
• To properly secure this child restraint it MUST
IMPORTANT: Once your child exceeds 18 kg (40 lbs)
OR is taller than 102 cm (40 in.) they can no longer
safely use this child restraint and you should consider
using a booster seat.
26
NOT move more than 25 mm (1 inch) from side
to side or front to back at the forward-facing
belt path (pages 31 and 35).
• The child’s back and bottom are flat against the
back and bottom surfaces of the child restraint.
• Shoulder harness straps MUST start at or above
shoulder height, using the strap slots closest to
your child’s shoulders (page 37).
• Buckle tongues are fully engaged.
• Tether strap is securely attached and tightened
(page 32 or 36).
27
Forward-facing
shoulders, with no slack (page 14).
• Crotch strap is snug against the child (page 39).
4.Fasten the buckle. Refer to page 14.
5.Position and connect chest clip.
Lift the child restraint and
flip the recline stand A
toward the rear, as shown,
to the Upright position.
A
Forward-facing Upright
The child restraint MUST be in the Upright position
for forward-facing use.
Child MUST weigh 10 – 18 kg (22 – 40 lbs) and be at
least one year of age.
28
Installing the Child Restraint
Forward-facing with Lower Anchor
Connector Assembly
LATCH is a system for attaching the child restraint to your
vehicle seat. It is to be used in place of your vehicle’s seat
belts, and can be used in vehicles with LATCH anchors.
Your vehicle owner’s manual may refer to this system
as ISOFIX, Universal Anchorage System (UAS), or Lower
Universal Anchorage System.
Note: Some vehicle manufacturers have lower
maximum weight ratings for vehicle lower anchor bars,
so you must consult your vehicle owner’s manual or call
the vehicle manufacturer to confirm the limits on your
vehicle’s lower anchor bars.
WARNING
• ONLY use for securing child restraint to vehicle lower
anchor bars.
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• NEVER attach two lower anchor connector hooks to one
vehicle lower anchor bar.
• DO NOT use the vehicle seat belts to install a child
restraint when using the lower anchor connector
assembly.
• This lower anchor connector assembly is intended to be
used ONLY as described in these instructions. Serious
injury or death may result from misuse.
• ALWAYS be sure that the lower anchor connector hook
is fully engaged onto the vehicle lower anchor bar by
pulling hard on the lower anchor connector strap. If it
is not totally engaged, the lower anchor connector
assembly will not secure your child restraint. Serious
injury or death may result.
• To avoid a strangulation hazard, you MUST store the
unused lower anchor connector assembly, with all slack
removed, in storage area on the back of the seat. Roll
or fold excess lower anchor connector strap and secure
with a rubber band to prevent serious injury to vehicle
occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of child
restraints and LATCH. If there is a discrepancy, follow
your vehicle owner’s manual.
29
Forward-facing
Positioning the Recline Stand for
Forward-facing Use
3
WARNING
DO NOT use the lowest set of harness slots for
forward-facing. The harness may not properly restrain
the child in the event of a crash.
B
A
Make sure
that the harness
straps are in one of the top three
strap slots A.
The harness straps MUST be at
or above shoulder height B,
using the strap slots closest to
your child’s shoulders. This will
provide more room for your
toddler to fit comfortably.
2
D
D
E
E
Refer to your vehicle owner’s manual to locate the
lower anchor bars on your vehicle seat. Attach the
right hook D to the right anchor bar E, and the left
hook to the left anchor bar.
DOUBLE CHECK that the lower anchor connector
hook is fully engaged by pulling hard on the lower
anchor connector strap.
4
C
C
Place the child restraint in your vehicle forwardfacing. Route the lower anchor connector strap and
hook through the forward-facing belt path C.
30
Using your full weight, push the child restraint firmly
into the vehicle seat, while pulling up on the lower
anchor connector strap to tighten.
The lower anchor connector strap must be as tight
as possible. If you can move the child restraint more
than 25 mm (1 in.) side to side or front to back at
the belt path C, the lower anchor connector strap is
not tight enough. You will need to try again, find
another location for your child restraint, or install with
the vehicle seat belt (page 33). To remove the lower
anchor connector strap, go to page 41.
WARNING
DO NOT use this child restraint if it moves more than
25 mm (1 in.) side-to-side or front to back at the
forward-facing belt path. Serious injury or death may result
from poor installation. If you can not tightly secure the child
restraint, try again, move it to another location, or install
with the vehicle seat belt.
31
Forward-facing
1
Installing the Child Restraint
Forward-facing with a Seat Belt
WARNING
• Failure to follow these instructions could result in
serious injury to your child or other vehicle occupants.
• The tether strap is for forward-facing use ONLY.
F
G
1
A
H
Connect the tether hook F to the vehicle tether
anchor G behind the vehicle seat, as shown. (Please
consult your vehicle owner’s manual, as tether anchor
locations may vary.) Pull the strap H and tighten the
tether securely.
WARNING
DO NOT use the lowest set of harness slots for
forward-facing. The harness may not properly restrain
the child in the event of a crash.
B
Make sure
that the harness
straps are in one
of the top three strap slots A.
The harness straps MUST be at
or above shoulder height B,
using the strap slots closest to
your child’s shoulders. This will
provide more room for your
toddler to fit comfortably.
2
Place the child restraint
in your vehicle
forward-facing.
WARNING
• To avoid a strangulation hazard, you MUST tightly
roll or fold excess tether strap and secure with the
strap/rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
After adjusting the top tether strap, you may have
excess strap; DO NOT cut it off. If you do, it may not
be long enough to use in another vehicle. Instead,
tightly roll up the excess tether strap and place the
rubber band around the bundle.
Note: Refer to your vehicle owner’s manual for the
location of the tether anchor brackets in your vehicle.
Older vehicles may not come equipped with anchor
bracket hardware. Check with your vehicle dealer.
If you have questions regarding tether anchors
which are not addressed by the vehicle owner’s
manual, or answered by an authorized dealer/vehicle
manufacturer call Evenflo’s ParentLink.
32
WARNING
3
If the vehicle belts are not
routed and fastened correctly,
the child restraint may not
protect your child in a crash.
Thread the vehicle seat
belt C through the
forward-facing belt path
behind the seat pad.
Note: Lift seat pad away
from seat for easier access.
C
33
Forward-facing
5
Lap & Shoulder Belt
Fasten the vehicle seat belt as shown depending on
your type of seat belt.
Note: Install locking clip on lap and shoulder belt
combinations, if necessary.
5
Install Locking Clip,
if necessary.
If your vehicle was built prior
to model year 1996, and
has either a lap belt or lap/
shoulder belt that is equipped
with an emergency locking
13 mm
retractor (ELR), you MUST
(0.5 inch)
use a Locking Clip. Check
your vehicle owner’s manual
to identify which vehicle belt
system is in your vehicle.
If your vehicle is model year 1996 or newer, it likely
has a vehicle belt system that can be locked when
tightened, and will not require use of a Locking Clip.
Locking Clip
installed properly
Consult your vehicle owner’s manual before installing
a locking clip.
6
D
The vehicle seat belt must be as tight as possible.
Using your full weight, push the child restraint firmly
into the vehicle seat as you tighten the vehicle belt. If
you can move the child restraint more than 25 mm (1
in.) side to side or front to back at the forward-facing belt
path D, the seat belt is not tight enough, you will need
to try again, or install with the lower anchor connector
assembly (page 29).
WARNING
• If vehicle seat belts are not routed and fastened correctly,
the child restraint may not protect your child in a crash.
• DO NOT use this child restraint if it moves more than 25
mm (1 in.) side to side or front to back at the
forward-facing belt path D. Serious injury or death may
result from poor installation. If you can not tightly secure
the child restraint, try again or move it to another
location, or install with the lower anchor connector
assembly (page 29).
If your vehicle requires a Locking Clip, please call
ParentLink (see back cover) to obtain a Locking Clip and
instructions on how to install and use it.
WARNING
• Remove Locking Clip from vehicle seat belt when not used
with a child restraint, or the vehicle seat belt will not properly
restrain an adult or child. Serious injury could occur.
34
35
Forward-facing
Lap Belt Only
Ä
4
Positioning the Harness Strap
7
E
Shoulder harness straps on this child restraint are
adjustable to four positions.
F
ONLY
C Forward-facing
Top Harness Position
G
B
Forward- OR Rear-facing
Middle Two Harness
Positions
A
Rear-facing ONLY
Lowest Harness Position
Connect the tether hook E to the vehicle tether
anchor F behind the vehicle seat, as shown. (Please
consult your vehicle owner’s manual, as tether anchor
locations may vary.) Pull the strap G and tighten the
tether securely.
WARNING
36
When Using in Rear-facing Position
The shoulder harness straps MUST ALWAYS be at or
below the child’s shoulders in one of the three lower
harness positions A or B and the child’s head MUST
be at least 25 mm (1 inch) below the top of the seat
back.
When Using in Forward-facing Position
The shoulder harness straps MUST ALWAYS be at
or above the child’s shoulders in one of the three
top harness position B or C. If the top of the child’s
ears are above the top of the seat back, the child’s
shoulders fall above the highest set of harness slots, or
the child weighs more than 18 kg (40 lbs) you MUST
discontinue use of this child restraint. We recommend
that you move your child to a larger child restraint or
booster seat.
37
General Information
• To avoid a strangulation hazard, you MUST tightly
roll or fold excess tether strap and secure with the
strap/rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
After adjusting the top tether strap, you may have
excess strap; DO NOT cut it off. If you do, it may not
be long enough to use in another vehicle. Instead,
tightly roll up the excess tether strap and place
the rubber band around the bundle.
Note: Refer to your vehicle owner’s manual for
the location of the tether anchor brackets in your
vehicle. Older vehicles may not come equipped with
anchor bracket hardware. Check with your vehicle
dealer.
If you have questions regarding tether anchors
which are not addressed by the vehicle owner’s
manual, or answered by an authorized dealer/vehicle
manufacturer call Evenflo’s ParentLink.
Adjusting the Crotch Strap
1
This Child Restraint Has Two Buckle Harness Positions
D
B
To change the harness strap position, loosen the
shoulder harness, as shown on page 39, step 2.
Slide the harness strap off of the splitter plate D.
We suggest you do this one side at a time.
Pull harness strap
through to the front
of the child restraint.
Thread each harness
strap through the
appropriate slot in
the seat shell and
the pad.
Pull the harness strap
to the back of the
child restraint.
3
Infant
Toddler
IMPORTANT: Make sure both harness straps are
installed completely on the splitter plate, as shown.
D
A
To reposition the crotch strap, first turn the child
restraint upside down. Turn the crotch strap harness
anchor A sideways and push it through the slot in
the bottom of the seat shell B.
Reposition the harness anchor into the other slot.
Make certain the harness anchor is properly seated
against the seat shell B.
Note: The crotch strap should be snug against the
child; choose the slot that is closest to the child AND
the most comfortable for the child.
Adjusting the Harness Strap
1
2
E
C
D
F
A
Infant
Toddler
There are two positions on the harness straps.
The top loop E is for infant use. The bottom loop
F is for use as your child grows. Reattach the harness
strap onto the splitter plate D. Repeat on the other side.
38
To tighten the harness
straps, pull on the long
harness adjuster strap A
on the front of the seat.
B
To loosen the harness
straps, push the harness
release button B on the
front of the seat. At the
same time, pull up on the
harness strap C near the
child’s shoulders.
39
General Information
Ä
2
A
Removing the Tether Strap
1
The tether strap that comes with your child
restraint will be one of the two types below.
A
Removing the Lower Anchor
Connectors
1
B
The Lower Anchor Connector that comes with
your child restraint will be one of the two types
below.
B
A
Press the adjuster release
button B to loosen
tether strap.
Tilt and slide the
adjuster A to loosen.
2
C
D
B
3
Press the tab B and
twist, then remove
the hook C from the
anchor D.
Tilt and slide the
adjuster A to loosen.
Press the adjuster release
button B to loosen.
2
B
D
C
WARNING
C
When the tether strap
is not in use you MUST
attach the hook C to
the back of the child
restraint, and tightly roll
and secure the strap with
the strap/rubber band.
A loose tether strap and
hook may injure your
child.
40
To remove the hook B, press the tab C and twist,
then remove from anchor D.
3
When the Lower anchor
connector assembly is
not in use you MUST
attach the hooks B to
the back of the child
restraint. A loose Lower
anchor connector
assembly strap and hook
may injure your child.
B
41
General Information
• To avoid a strangulation hazard, you MUST tightly
roll or fold excess tether strap and secure with the
strap/rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
Installing the Accessories
Not available on all models.
To install the cup holder
A, peel back the seat pad
B and insert the hook on
the cup holder into the slot
in seat, as shown. Replace
pad over the seat.
B
A
To use the cup holder A fold down the lid and swing
the holding arms up.
WARNING
• DO NOT use the cup holder to store bottles or hard
containers. Only for use with soft cups (such as
styrofoam or paper).
• DO NOT place any cups that contain hot liquids in
the cup holder.
• DO NOT attach any other items to this child restraint
unless it has been certified for use with this specific
child restraint.
D
• To help protect the vehicle upholstery, place a
towel beneath and behind the child restraint.
• Plastic and metal parts may be wiped clean with mild
soap and water and dried with a soft cloth. DO NOT
use abrasive cleaners or solvents.
• Take care not to damage any labels.
• The harness can be wiped clean with mild soap and
water. Allow harness to air dry. DO NOT immerse
buckle in water or lubricate buckle.
• The seat pad can be machine washed separately in
cold water, delicate cycle, tumble dry 10 – 15 minutes
on low heat.
• NEVER use child restraint without the seat pad.
• Leather pads (not available on all models) may be
cleaned. For best results spot clean with mild soap
and water or with a mixture of 10 parts water to
1 part mild alcohol. Allow to air dry. DO NOT
MACHINE WASH.
Proper Disposal of this Child Restraint
At the end of this child restraint’s useful life, Evenflo
encourages you to dispose of it properly. Most of the
components in this child restraint are recyclable.
1. Remove all fabric and padding.
2. Remove all screws and disassemble the restraint.
3. Recycle all plastic/foam parts and discard the rest.
If your local recycling center won’t accept the padding,
you may dispose of it in the landfill.
Note: Evenflo uses recycled materials in the manufacturing
process whenever possible but never for components that are
critical for safety.
The optional Head Pillow C
attaches easily and is used
to help support the child’s
head.
Note: Styles may vary.
General Information
C
Care and Cleaning
The optional Body Pillow D
is used to help support your
child by placing it in the
restraint, as shown.
42
43
Securing Your Child Restraint in
Aircraft
The Federal Aviation Administration (FAA) recommends
that you secure your child for air travel in an appropriate
child restraint based on your child’s weight and size.
Turbulence can happen with little or no warning. When
turbulence occurs, the safest place for your child is
in a properly installed child restraint, not in an
adult’s lap or on the aircraft seat with its seat
belt. Keeping your child in a child restraint during the
flight will help ensure your family arrives safely at your
destination.
Installing Child Restraint Rear-facing
in Aircraft
2
B
C
The FAA recommends that a child weighing:*
• more than 18 kg (40 lbs) use an aircraft seat belt;
• less than 9 kg (20 lbs) use a rear-facing child
restraint; and
• from 9 to 18 kg (20 to 40 lbs) use a forward-facing
child restraint.
* Please note that these FAA recommendations
may vary from those applicable to the use of
your child restraint in a motor vehicle.
IMPORTANT
You must use the internal harness when installing the
child restraint in aircraft.
Installing Child Restraint Rear-facing
in Aircraft
A
Pull the seat pad off the front of the child restraint.
Route the aircraft seat belt A through the rear-facing
belt path B opening on one side and continue
through the belt path opening on the opposite side
of the child restraint, as shown above.
3
IMPORTANT: Before installing the child restraint, make
sure the aircraft seat is in a fully upright position.
E
1
Arrow MUST be level
with ground when used
Rear-Facing
REAR OF VEHICLE
Aircraft
Seat Belt
Adjust the child restraint to its recline position (page
18), then place it on the aircraft seat rear-facing, as
shown above.
44
D
C
When the crotch strap E
is in the front slot, route
aircraft seat belt C behind
the crotch strap, as shown.
When the crotch strap E
is in the rear slot, rout
aircraft seat belt C in
front of the crotch strap,
as shown.
45
General Information
E
Installing Child Restraint Rear-facing
in Aircraft
4
Installing Child Restraint Forward-facing
in Aircraft
IMPORTANT: Before installing the child restraint, make
sure the aircraft seat is in a fully upright position.
1
A
Fasten the aircraft seat belt A.
5
Aircraft
Seat Belt
D
B
Adjust the child restraint to its upright position (page
28), then place it on the aircraft seat forward-facing, as
shown above.
2
A
B
Check your work. Reconnect the seat pad to the front
of the child restraint. Try to move the child restraint in
all directions. If you can move the restraint more than
25 mm (1 inch) from side to side or front to back at the
rear-facing belt path B, the aircraft seat belt A is not
tight enough, and you MUST install again until the seat
belt is tight.
46
A
Route the aircraft seat belt A through the forwardfacing belt path opening in the back of the child
restraint and continue through the belt path opening
B on the opposite side of the child restraint.
Note: Lift the restraint’s seat pad away for easier
access.
47
General Information
The aircraft seat belt A must be as tight as possible.
Route the excess seat belt strap D back through the
rear-facing belt path B opening, as shown above.
Using your full weight, push the child restraint firmly
onto the aircraft seat while pulling on the excess seat
belt strap to tighten.
Replacement Parts
Installing Child Restraint Forward-facing
in Aircraft
3
Not available on all models. Styles may vary.
To order replacement parts you can order on-line at
www.evenflo.com or contact Evenflo. When you contact
us, please have the product model number and date of
manufacture (found on the back of the child restraint).
A
1
Locking Clip:
Not included with
child restraint, see
page 24 or 34
Fasten the aircraft seat belt A.
4
2 Chest Clip
D
8 Head Pillow
5
Harness
System
9 Body Pillow
10 EPS Foam
3 Retainer Strip
C
Lower
Anchor
Connector
Assembly
6
11 Head Foam
4 Tether
7 Cup Holder
12
49
Seat pad &
Retainer Strips
General Information
The aircraft seat belt must be as tight as possible. Route
the excess aircraft seat belt strap C back through the
forward-facing belt path D opening, as shown above.
Using your full weight, push the child restraint firmly
onto the aircraft seat while pulling on the excess seat
belt strap to tighten.
Note: Because of the fixed length of aircraft seat belts, the
belt buckle could be behind the child’s back after tightening
the belt. For your child’s comfort, Evenflo recommends
cushioning the child’s back by placing a small pillow or
folded-up blanket, or a folded-up jacket, over the belt buckle.
Check your work. Reconnect the seat pad to the front
of the child restraint. Try to move the child restraint in
all directions. If you can move the restraint more than
25 mm (1 inch) from side to side or front to back at the
forward-facing belt path, the aircraft seat belt is not tight
enough, and you MUST install again until the seat belt
is tight.
48
Limited Warranty
For a period of 90 days from the original purchase of
this Product, Evenflo warrants to the original end user
(“Purchaser”) this Product (including any accessories)
against defects in material or workmanship. Evenflo’s
sole obligation under this express limited warranty
shall be, at Evenflo’s option, to repair or replace any
Product that is determined to be defective by Evenflo
and determined to be covered by this warranty.
Repair or replacement as provided under this
warranty is the exclusive remedy of the Purchaser.
Proof of purchase in the form of a receipted invoice
or bill of sale evidencing that the Product is within
the warranty period must be presented to obtain
warranty service. This express limited warranty is
extended by Evenflo ONLY to the original Purchaser
of the Product and is not assignable or transferable to
subsequent purchasers or end users of the Product.
For warranty service, contact Evenflo’s ParentLink
Consumer Resource Center at www.evenflo.com.
EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBY
DISCLAIMED. EVENFLO SHALL NOT BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL,
SPECIAL OR PUNITIVE DAMAGES OF ANY KIND
FOR BREACH OF THE EXPRESS LIMITED WARRANTY
ON THIS PRODUCT, OR ANY WARRANTY IMPLIED BY
OPERATION OF LAW. OTHER THAN THE EXPRESS
LIMITED WARRANTY SET FORTH ABOVE, THERE ARE
NO OTHER WARRANTIES THAT ACCOMPANY THIS
PRODUCT AND ANY ORAL, WRITTEN OR ANY OTHER
EXPRESS REPRESENTATION OF ANY KIND IS HEREBY
DISCLAIMED.
• USA: 1-800-233-5921, 8 AM to 5 PM E.T.
• Canada: 1-937-773-3971
• México: 01-800-706-12-00
50
INSTRUCTIONS
• USA: 1-800-233-5921, 8 AM to 5 PM E.T.
• Canada: 1-937-773-3971
• México: 01-800-706-12-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising