Regular Analog Setting Instructions

Regular Analog Setting Instructions
Regular Analog Setting Instructions
Note: Your model may not feature
a second hand or day/day-date feature
Caution
Before using the watch, READ this instruction
manual carefully for safe and correct use. After
reading this manual, keep it properly for your future
reference.
SAFETY PRECAUTIONS (Please observe at all
times)
In order to prevent injury to yourself or other persons
and damage to property, this manual describes the
instructions that you should strictly follow as follows.
■ Injuries and damages which might be caused by
using the watch improperly, neglecting any of the
instructions or precautions in this manual are
classified with the following symbols.
Warning
Caution
Can cause serious injury or death
Can or will cause minor or moderate
injury or damage
SPECIFICATIONS
1. Quartz oscillation frequency: 32,768Hz (Hz =
number of vibrations per second)
2. Converter: Step motor
3. Additional functions: Calendar quick setting
function (applies to watches equipped with day as
well as day and month calendar functions)
4. IC (integrated circuit): 1C/MOS-LSI
5. Accuracy: within ±◊ 15 to 20 seconds
per month at normal temperature
(+5°C≈+35°C))
6. Battery: One silver oxide
CAL
Accuracy
Battery
Life
CAL
Accuracy
Battery
Life
CAL
Accuracy
Battery
Life
1010
20
1020
20
1030
20
1110
20
3220
20
4520
15
461*
20
4633
20
464*
20
3
4713
20
5
477*
20
3
5421
20
3
5431
20
3
5500
20
2
5510
20
2
5530
20
2
5920
20
2
5930
20
3
6010
20
2
6020
20
3
6031
20
2
604*
20
5
6115
20
5
6790
20
5
7630
30
2
9620
20
2
9630
20
3
3
3
3
3
3
2
2
2
The above specifications are subject to change
without prior notification.
SETTING INSTRUCTIONS
1. Setting the Time and Date
(1) Stop the second hand in the “0 seconds” position
by pulling out the crown to 2 then turn crown to
set watch hands to the correct time. In case of a
screw lock-type crown, place in position 2 after
unlocking the screw.
(2) After setting watch to the correct time and
returning crown to the 0 position, the second
hand will be activated and the watch will
commence to keep accurate time.
Due to the mechanical structure of the watch, the
step position of the second hand is not aligned
with the scale on the face. This does not have an
effect on the accuracy, however.
Note:
a. To achieve optimal precision when setting the
minute hand, move the minute hand four to five
minutes past and then back to the desired setting.
b. For calendar-equipped watches, do not confuse
AM and PM settings.
c. For watches equipped with locking screw-type
crowns, do not forget to return the crown to the
locked position after setting watch.
2. Setting the calendar
(1) Pull out crown to position 1
(2) Set date by turning crown to the left.
(3) Set day by turning crown to the right.
*For watches equipped with date display only,
date is set by turning crown to the right.
(4) Return crown to 0 position.
Note:
Avoid performing the calendar quick setting operation
between the below listed times:
For watches equipped with date display...9.00 PM1:00 AM
For watches equipped with both date and day
display...9:00 PM-4:30 AM
If the calendar quick setting operation is performed
between these times the calendar could be
incorrectly set to the date of the previous day.
After setting watch hands during these times, set
time, day and date accordingly.
PRECAUTIONS ABOUT CARE AND
HANDLING OF WATCHES
TEMPERATURE CARE
Avoid temperature extremes. Exposing your watch to high
temperatures, such as placing it on the dashboard of a vehicle
or use in a hot tub, may cause the watch to malfunction,
shorten battery life or damage certain components. Leaving
the watch in extreme cold temperatures may cause irregular
timekeeping until the watch returns to normal operating
temperature.
SHOCK-RESISTANT
The watch may be worn while playing golf or other activities,
but avoid severe shocks such as dropping it on a hard surface.
MAGNETIC-RESISTANT
No problem should occur from using the watch around
ordinary household electric appliances such as TV sets or
stereos. Keep away from magnets.
CHEMICAL/GAS RESISTANT
Do not expose the watch to chemicals or gases for long
periods.
WATCH CLEANING
Stains, waterspots and accumulated dirt on the case, crystal
or band should be removed with a soft cloth to prevent
damage and premature wear.
HANDLING OF WATER-RESISTANT WATCHES
Although water-resistant watches are warranted, steps should
be taken to avoid damage that may result from
accidents or mishandling:
■ Do not operate the crown or push-button in the water or
while the watch is wet. Tighten screw lock crown completely.
■ Should the watch become immersed in water, dry it off
right away. If the watch comes in contact with salt water, be
sure to rinse it thoroughly in warm fresh water to remove any
trace of salt.
■ If a watch is wet from cleaning or by accident, never store it
in a closed container. It should be dried immediately or taken
to a watchmaker or jeweler if moisture is inside the case to
prevent damage from rust.
■ Vital components necessary to resist the entrance of
moisture deteriorate with time and use. Gaskets, crowns and
other materials should be replaced every year or two to ensure
that water resistant quality remains at factory specifications.
CARE FOR METAL BRACELETS
To extend the life and maintain the good appearance of the
metal watch bracelet, the following recommendations are
given:
■ Be aware that since the watch and bracelet is worn next to
the skin, it collects dust and perspiration and becomes soiled if
not cleaned regularly. This is particularly true of the inner parts
of the links or mesh of the bracelet.
■ Soil and rust, when present in a bracelet, are dissolved by
perspiration and can cause staining of cuffs and
irritation of the skin in some instances.
■ Heavy perspiration should be wiped off the watch and
bracelet with a soft dry cloth. The bracelet should be cleaned
occasionally by using an old toothbrush and warm soapy
water after which the soap is thoroughly rinsed with clear water
and the bracelet dried completely. The foregoing manner of
cleaning should not be done if the watch is not water-resistant
but should instead be done by your jeweler.
CARE FOR STRAPS
LEATHER
■ Heavy perspiration, if not removed from a leather strap, can
wash out the natural oils and cause the leather to become dry
and deteriorate. Any moisture should be blotted with a soft dry
cloth or paper towel and the strap allowed to dry naturally.
■ Salt residue and soil can be removed from the leather by
cleaning with a dampened soft cloth and mild soap or saddle
soap.
■ Occasionally, the inside surface of the strap should be
cleaned by using a soft cloth dampened with alcohol.
■ The strap should always be worn a little loosely (one finger
space between wrist and strap) to allow air to circulate thus
causing any moisture to evaporate.
RUBBER
■ Rubber straps should be washed frequently with mild soap
and warm water using a soft brush.
■ Thorough cleaning, using the same method, should
especially be done after use in salt water.
■ Solvents, oils, perspiration, tanning lotion and salt can cause
rubber to deteriorate if not removed.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement