2012 Dodge Durango Owner`s Manual

2012 Dodge Durango Owner`s Manual
2012 Durango
2012
OWNER’S MANUAL
Chrysler Group LLC
12WD01-126-AF
Sixth Edition
Printed in U.S.A.
Durango
VEHICLES SOLD IN CANADA
With respect to any Vehicles Sold in Canada, the name
Chrysler Group LLC shall be deemed to be deleted and the
name Chrysler Canada Inc. used in substitution therefore.
DRIVING AND ALCOHOL
Drunken driving is one of the most frequent causes of
accidents.
Your driving ability can be seriously impaired with blood
alcohol levels far below the legal minimum. If you are
drinking, don’t drive. Ride with a designated non-drinking
driver, call a cab, a friend, or use public transportation.
This manual illustrates and describes the operation of
features and equipment that are either standard or optional
on this vehicle. This manual may also include a description
of features and equipment that are no longer available or
were not ordered on this vehicle. Please disregard any
features and equipment described in this manual that are
not on this vehicle.
Chrysler Group LLC reserves the right to make changes in
design and specifications, and/or make additions to or
improvements to its products without imposing any obligation upon itself to install them on products previously
manufactured.
WARNING!
Driving after drinking can lead to an accident. Your
perceptions are less sharp, your reflexes are slower,
and your judgment is impaired when you have been
drinking. Never drink and then drive.
Copyright © 2011 Chrysler Group LLC
SECTION
TABLE OF CONTENTS
PAGE
1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
3
4
UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
4
5
STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
5
6
WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549
6
7
MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579
7
8
MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637
8
9
IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653
9
10
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663
10
INTRODUCTION
1
CONTENTS
䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 8
䡵 Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Identification Number
.............. 8
䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 9
4 INTRODUCTION
INTRODUCTION
Congratulations on selecting your new Chrysler Group
LLC vehicle. Be assured that it represents precision
workmanship, distinctive styling, and high quality - all
essentials that are traditional to our vehicles.
This is a specialized utility vehicle. It can go places and
perform tasks that conventional passenger cars are not
intended. It handles and maneuvers differently from
many passenger cars both on-road and off-road, so take
time to become familiar with your vehicle.
The two-wheel drive version of this vehicle was designed
for on-road use only. It is not intended for off-road
driving or use in other severe conditions suited for a
four-wheel drive vehicle.
handles on different road surfaces. Your driving skills
will improve with experience. When driving off-road or
working the vehicle, don’t overload the vehicle or expect
the vehicle to overcome the natural laws of physics.
Always observe federal, state, provincial and local laws
wherever you drive.
As with other vehicles of this type, failure to operate this
vehicle correctly may result in loss of control or a
collision. Refer to “On-Road/Off-Road Driving Tips” in
“Starting And Operating” for further information.
This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint
you with the operation and maintenance of your vehicle.
It is supplemented by Warranty Information, and various
customer-oriented documents. Please take the time to
Before you start to drive this vehicle, read the Owner’s
read these publications carefully. Following the instrucManual. Be sure you are familiar with all vehicle controls,
tions and recommendations in this manual will help
particularly those used for braking, steering, transmisassure safe and enjoyable operation of your vehicle.
sion, and transfer case shifting. Learn how your vehicle
INTRODUCTION 5
NOTE:
After reviewing the owner information, it Do not attempt sharp turns, abrupt maneuvers, or other
should be stored in the vehicle for convenient referenc- unsafe driving actions that can cause loss of vehicle
control. Failure to operate this vehicle safely may result
ing and remain with the vehicle when sold.
in a collision, rollover of the vehicle, and severe or fatal
When it comes to service, remember that your authorized
injury. Drive carefully.
dealer knows your vehicle best, has factory-trained technicians and genuine MOPAR威 parts, and cares about
your satisfaction.
ROLLOVER WARNING
Utility vehicles have a significantly higher rollover rate
than other types of vehicles. This vehicle has a higher
ground clearance and a higher center of gravity than
many passenger cars. It is capable of performing better in
a wide variety of off-road applications. Driven in an
unsafe manner, all vehicles can go out of control. Because
of the higher center of gravity, if this vehicle is out of
control it may roll over when some other vehicles may
not.
Rollover Warning Label
1
6 INTRODUCTION
Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the
U.S. government notes that the universal use of existing
seat belts could cut the highway death toll by 10,000 or
more each year and could reduce disabling injuries by
two million annually. In a rollover crash, an unbelted
person is significantly more likely to die than a person
wearing a seat belt. Always buckle up.
HOW TO USE THIS MANUAL
Consult the Table of Contents to determine which section
contains the information you desire.
Since the specification of your vehicle depends on the
items of equipment ordered, certain descriptions and
illustrations may differ from your vehicle’s equipment.
The detailed index at the back of this Owner’s Manual
contains a complete listing of all subjects.
Consult the following table for a description of the
symbols that may be used on your vehicle or throughout
this Owner’s Manual:
INTRODUCTION 7
8 INTRODUCTION
WARNINGS AND CAUTIONS
This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or
bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you
do not read this entire manual, you may miss important
information. Observe all Warnings and Cautions.
VEHICLE IDENTIFICATION NUMBER
The Vehicle Identification Number (VIN) is found on a
plate located on the left front corner of the instrument
panel pad, visible from outside of the vehicle through the
windshield and is stamped into the right front body,
behind the right front seat. Move the right front seat
forward to allow better viewing of the stamped VIN. The
VIN is also located on the Automobile Information
Disclosure Label affixed to a window on your vehicle.
Save this label for a convenient record of your vehicle
identification number and optional equipment.
VIN Location
INTRODUCTION 9
VEHICLE MODIFICATIONS/ALTERATIONS
WARNING!
Any modifications or alterations to this vehicle could
seriously affect its roadworthiness and safety and
may lead to a collision resulting in serious injury or
death.
Right Front Body VIN Location
NOTE: It is illegal to remove or alter the VIN.
1
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
2
CONTENTS
䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 14
䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 20
▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 14
▫ Rearming The System . . . . . . . . . . . . . . . . . . 21
▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
▫ To Arm The System . . . . . . . . . . . . . . . . . . . 21
▫ Removing Key Fob From Ignition . . . . . . . . . . 16
▫ To Disarm The System . . . . . . . . . . . . . . . . . 22
▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . 18
▫ Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . 23
䡵 Sentry Key威 . . . . . . . . . . . . . . . . . . . . . . . . . . 18
䡵 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . 23
▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . 19
䡵 Remote Keyless Entry (RKE)
. . . . . . . . . . . . . . 24
▫ Customer Key Programming . . . . . . . . . . . . . 20
▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . 25
▫ General Information . . . . . . . . . . . . . . . . . . . 20
▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . 26
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 26
䡵 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
▫ Programming Additional Transmitters . . . . . . 26
▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . 42
▫ Transmitter Battery Replacement . . . . . . . . . . 27
▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 45
▫ General Information . . . . . . . . . . . . . . . . . . . 29 䡵 Liftgate
䡵 Remote Starting System — If Equipped . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
▫ Power Liftgate — If Equipped . . . . . . . . . . . . 46
▫ How To Use Remote Start . . . . . . . . . . . . . . . 30 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 48
䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . 52
▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . 34
▫ Lap/Shoulder Belt Operating Instructions . . . . 53
▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . 35
▫ Lap/Shoulder Belt Untwisting Procedure . . . . 56
▫ Child-Protection Door Lock System — Rear
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
▫ Adjustable Upper Shoulder Belt Anchorage . . . 57
䡵 Keyless Enter-N-Go™ . . . . . . . . . . . . . . . . . . . 38
▫ Seat Belts In Passenger Seating Positions . . . . . 58
▫ Automatic Locking Retractor Mode (ALR) —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
▫ Energy Management Feature . . . . . . . . . . . . . 60
▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 80
▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . 60
▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . 81
▫ Supplemental Active Head Restraints (AHR) . . 61
䡵 Engine Break-In Recommendations . . . . . . . . . . 97
▫ Enhanced Seat Belt Use Reminder System
(BeltAlert威) . . . . . . . . . . . . . . . . . . . . . . . . . 65
䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
▫ Seat Belts And Pregnant Women . . . . . . . . . . 66
▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 66
▫ Supplemental Restraint System (SRS) — Air
Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
▫ Advanced Front Air Bag Features . . . . . . . . . . 69
▫ Air Bag Deployment Sensors And Controls . . . 73
▫ Transporting Passengers . . . . . . . . . . . . . . . . 98
▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 98
▫ Safety Checks You Should Make Inside The
Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
▫ Periodic Safety Checks You Should Make
Outside The Vehicle . . . . . . . . . . . . . . . . . . 101
2
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
A WORD ABOUT YOUR KEYS
Your vehicle uses a keyless ignition system. This system
consists of a Key Fob with Remote Keyless Entry (RKE)
transmitter and a Wireless Ignition Node (WIN) with
integral ignition switch. You can insert the Key Fob into
the ignition switch with either side up.
Wireless Ignition Node (WIN)
The Wireless Ignition Node (WIN) operates similar to an
ignition switch. It has four operating positions, three of
which are detented and one spring-loaded. The detented
positions are OFF, ACC, and ON/RUN. The START
position is a spring-loaded momentary contact position.
When released from the START position, the switch
automatically returns to the detented ON/RUN position.
Keyless Enter-N-Go Feature
This vehicle is equipped with the Keyless Enter-N-Go
feature, refer to “Starting Procedures” in “Starting And NOTE: With the Keyless Enter-N-Go feature, the ElecOperating” for further information.
tronic Vehicle Information Center (EVIC) will display the
ignition switch position (OFF/ACC/RUN). Refer to
“Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
Key Fob
The Key Fob operates the ignition switch. Insert the
square end of the key fob into the ignition switch located
on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE)
transmitter and an emergency key, which stores in the
rear of the Key Fob.
Wireless Ignition Node (WIN)
1
2
3
4
— OFF
— ACC (ACCESSORY)
— ON/RUN
— START
The emergency key allows for entry into the vehicle on
the driver’s side should the battery in the vehicle or the
RKE transmitter go dead. The emergency key is also for
locking the glove box. You can keep the emergency key
with you when valet parking.
NOTE: Entering a vehicle using the emergency key with
the theft alarm armed, will result in the alarm sounding.
Insert the Key Fob (even if the Key Fob battery is dead)
into the ignition switch to disarm theft alarm.
2
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition
at the top of the Key Fob sideways with your thumb and Place the shift lever in PARK. Turn the Key Fob to the
OFF position and then remove the Key Fob.
then pull the key out with your other hand.
With the Keyless Enter-N-Go feature, the EVIC will
display the ignition switch position “OFF/ACC/RUN”.
Refer to “Electronic Vehicle Information Center (EVIC)”
in “Understanding Your Instrument Panel” for further
information.
NOTE:
• If you try to remove the Key Fob before you place the
shift lever in PARK, it may become trapped temporarily in the ignition switch. If this occurs, place the shift
lever in PARK, rotate the key to the right slightly, then
remove the Key Fob as described. If a malfunction
Emergency Key Removal
occurs, the system will trap the key in the ignition
switch to warn you that this safety feature is inoperNOTE: You can insert the double-sided emergency key
able. The engine can be started and stopped, but the
into the lock cylinders with either side up.
Key Fob cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
• The power window switches, radio, power sunroof (if
equipped), and power outlets will remain active for up
to 10 minutes after the ignition switch is turned to the
OFF position. Opening either front door will cancel
this feature. The time for this feature is programmable.
Refer to “Electronic Vehicle Information Center
(EVIC)/Personal Settings (Customer-Programmable
Features)” in “Understanding Your Instrument Panel”
for further information.
CAUTION!
• If your vehicle battery becomes low or dead, your
Key Fob will become locked in the ignition.
• Do not attempt to remove the Key Fob while in
this condition, damage could occur to the Key Fob
or ignition module. Only remove the emergency
key for locking and unlocking the doors.
(Continued)
CAUTION! (Continued)
• Leave the Key Fob in the ignition and either:
• Jump Start the vehicle.
• Charge the battery.
WARNING!
• When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or
others could be seriously or fatally injured. Children should be warned not to touch the parking
brake, brake pedal or the shift lever.
(Continued)
2
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING! (Continued)
• Do not leave the key fob in or near the vehicle, and
do not leave Keyless Enter-N-Go in the ACC or
ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
CAUTION!
An unlocked car is an invitation to thieves. Always
remove Key Fob from the ignition and lock all doors
when leaving the vehicle unattended.
Key-In-Ignition Reminder
Opening the driver’s door when the Key Fob is in the
ignition and the ignition switch position is OFF or ACC,
sounds a signal to remind you to remove the Key Fob.
NOTE: The Key-In-Ignition reminder only sounds
when the Key Fob is placed in the OFF or ACC ignition
position.
With the Keyless Enter-N-Go feature, opening the driver’s door when the vehicle’s ignition switch is placed in
ACC or ON/RUN (engine stopped) will cause the reminder chime to sound. Refer to “Starting Procedures” in
“Starting And Operating” for further information.
SENTRY KEY姞
The Sentry Key威 Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The
system does not need to be armed or activated. Operation
is automatic, regardless of whether the vehicle is locked
or unlocked.
The system uses the factory-mated Key Fob with Remote
Keyless Entry (RKE) transmitter and Wireless Ignition
Node (WIN) to prevent unauthorized vehicle operation.
Therefore, only Key Fobs that are programmed to the
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
vehicle can be used to start and operate the vehicle. The
system will shut the engine off in two seconds if an
invalid Key Fob is used to start the engine.
CAUTION!
The Sentry Key威 Immobilizer system is not compatible with some after-market remote starting systems.
Use of these systems may result in vehicle starting
problems and loss of security protection.
After turning the ignition switch to the ON/RUN position, the Vehicle Security Light will turn on for three
seconds for a bulb check. If the light remains on after the
bulb check, it indicates that there is a problem with the
All of the Key Fobs provided with your new vehicle have
electronics. In addition, if the light begins to flash after
been programmed to the vehicle electronics.
the bulb check, it indicates that someone used an invalid
Key Fob to start the engine. Either of these conditions will Replacement Keys
result in the engine being shut off after two seconds.
NOTE: Only Key Fobs that are programmed to the
If the Vehicle Security Light turns on during normal vehicle electronics can be used to start and operate the
vehicle operation (vehicle running for longer than 10 sec- vehicle. Once a Key Fob is programmed to a vehicle, it
onds), it indicates that there is a fault in the electronics. cannot be programmed to any other vehicle.
Should this occur, have the vehicle serviced as soon as
possible by an authorized dealer.
2
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CAUTION!
• Always remove the Key Fobs from the vehicle and
lock all doors when leaving the vehicle unattended.
• With Keyless Enter-N-Go, always remember to
place the ignition in OFF.
At the time of purchase, the original owner is provided
with a four-digit Personal Identification Number (PIN).
Keep the PIN in a secure location. This number is
required for authorized dealer replacement of Key Fobs.
Duplication of Key Fobs may be performed at an authorized dealer, this procedure consists of programming a
blank Key Fob to the vehicle electronics. A blank Key Fob
is one that has never been programmed.
Customer Key Programming
Programming Key Fobs or RKE transmitters may be
performed at an authorized dealer.
General Information
The Sentry Key威 system complies with FCC rules Part 15
and with RSS-210 of Industry Canada. Operation is
subject to the following conditions:
• This device may not cause harmful interference.
• This device must accept any interference that may be
received, including interference that may cause undesired operation.
VEHICLE SECURITY ALARM — IF EQUIPPED
This Vehicle Security Alarm monitors the vehicle doors,
liftgate, liftgate flipper glass, and ignition for unauthorNOTE: When having the Sentry Key威 Immobilizer ized operation. When the alarm is activated, the interior
system serviced, bring all vehicle Key Fobs with you to switches for door locks, power liftgate and flipper glass
are disabled. The Vehicle Security Alarm provides both
the authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
audio and visual signals, the horn will sound, the headlights will turn on, park lamps and/or turn signals will
flash repeatedly for three minutes. If the disturbance is
still present (driver’s door, passenger door, other doors,
ignition) after three minutes, the headlights, park lamps
and/or turn signals will flash for an additional 15 minutes.
To Arm The System
Follow these steps to arm the Vehicle Security Alarm:
1. Remove the key from the ignition system (refer to
⬙Starting Procedures⬙ in ⬙Starting And Operating⬙ for
further information).
• For vehicles equipped with Keyless Enter-N-Go, make
sure the vehicle ignition system is ⬙OFF⬙.
NOTE: The Panic and Security alarms are quite different. Please take a moment to activate the Panic and the • For vehicles not equipped with Keyless Enter-N-Go,
Security modes to hear the differences in the horn. In case make sure the vehicle ignition system is ⬙OFF⬙ and the
one should go off in the future, you will need to know key is physically removed from the ignition.
which mode has been activated in order to deactivate it.
2. Perform one of the following methods to lock the
Rearming The System
vehicle:
If something triggers the alarm, and no action is taken to
• Press LOCK on the interior power door lock switch
disarm it, the Vehicle Security Alarm will turn off the
with the driver and/or passenger door open.
horn after three minutes, turn off all of the visual signals
after 15 minutes, and then the Vehicle Security Alarm will • Press the LOCK button on the exterior Passive Entry
rearm itself.
Door Handle with a valid Key Fob available in the same
2
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
exterior zone (refer to ⬙Keyless Enter-N-Go⬙ in ⬙Things To • Cycle the vehicle ignition system out of the OFF
Know Before Starting Your Vehicle⬙ for further informaposition.
tion).
• For vehicles equipped with Keyless Enter-N-Go,
press the Keyless Enter-N-Go Start/Stop button
• Press the LOCK button on the Remote Keyless Entry
(requires at least one valid Key Fob in the vehicle).
(RKE) transmitter.
3. If any doors are open, close them.
• For vehicles not equipped with Keyless Enter-N-Go,
insert a valid key into the ignition switch and turn
the key to the ON position.
To Disarm The System
The Vehicle Security Alarm can be disarmed using any of
the following methods:
NOTE:
• The driver’s door key cylinder and the liftgate button
• Press the UNLOCK button on the Remote Keyless
on the RKE transmitter cannot arm or disarm the
Entry (RKE) transmitter.
Vehicle Security Alarm.
• Grasp the Passive Entry Unlock Door Handle (if
• The Vehicle Security Alarm remains armed during
equipped, refer to ⬙Keyless Enter-N-Go⬙ in ⬙Things To
power liftgate entry. Pressing the liftgate button will
Know Before Starting Your Vehicle⬙ for further infornot disarm the Vehicle Security Alarm. If someone
mation).
enters the vehicle through the liftgate and opens any
door the alarm will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23
• When the Vehicle Security Alarm is armed, the interior Tamper Alert
power door lock switches will not unlock the doors. If something has triggered the Vehicle Security Alarm in
your absence, the horn will sound three times and the
The Vehicle Security Alarm is designed to protect your
exterior lights blink three times when you unlock the
vehicle; however, you can create conditions where the
doors. Check the vehicle for tampering.
system will give you a false alarm. If one of the previously described arming sequences has occurred, the ILLUMINATED ENTRY
Vehicle Security Alarm will arm regardless of whether The courtesy lights will turn on when you use the
you are in the vehicle or not. If you remain in the vehicle Remote Keyless Entry (RKE) transmitter to unlock the
and open a door, the alarm will sound. If this occurs, doors or open any door.
disarm the Vehicle Security Alarm.
This feature also turns on the approach lighting in the
If the Vehicle Security Alarm is armed and the battery outside mirrors (if equipped). Refer to “Mirrors” in
becomes disconnected, the Vehicle Security Alarm will “Understanding The Features Of Your Vehicle” for furremain armed when the battery is reconnected; the ther information.
exterior lights will flash, the horn will sound. If this
The lights will fade to off after approximately 30 seconds
occurs, disarm the Vehicle Security Alarm.
or they will immediately fade to off once the ignition
switch is turned to ON/RUN from the OFF position.
2
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: Inserting the Key Fob with RKE transmitter into
the ignition switch disables the system from responding
to any button presses from that RKE transmitter. Driving
at speeds 5 mph (8 km/h) and above disables the system
from responding to all RKE transmitter buttons for all
• The Illuminated Entry system will not operate if the
RKE transmitters.
dimmer control is in the “Dome defeat” position
(extreme bottom position).
NOTE:
• The front courtesy overhead console and door courtesy lights will turn on if the dimmer control is in the
⬙Dome ON⬙ position (extreme top position).
REMOTE KEYLESS ENTRY (RKE)
This system allows you to lock or unlock the doors and
liftgate, or activate the panic alarm, from distances up to
approximately 66 ft (20 m) using a hand-held Key Fob
with RKE transmitter. The RKE transmitter does not need
to be pointed at the vehicle to activate the system.
Key Fob With Five-Button RKE Transmitter
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
Flash Lamps With Lock
This feature will cause the turn signal lamps to flash
when the doors are locked or unlocked with the RKE
transmitter. This feature can be turned on or off. To
change the current setting, refer to “Electronic Vehicle
Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your InstruRefer to “Keyless Enter-N-Go” under “Things To Know
ment Panel” for further information.
Before Starting Your Vehicle” for further information.
Illuminated Approach
Remote Unlock Sequence
This feature activates the headlights for up to 90 seconds
This feature lets you program the system to unlock either
when the doors are unlocked with the RKE transmitter.
the driver’s door or all doors, on the first press of the
The time for this feature is programmable on vehicles
UNLOCK button on the RKE transmitter. To change
equipped with the Electronic Vehicle Information Center
the current setting, refer to “Electronic Vehicle Infor(EVIC). Refer to “Electronic Vehicle Information Center
mation Center (EVIC)/Personal Settings (Customer(EVIC)/Personal Settings (Customer-Programmable
Programmable Features)” in “Understanding Your InstruFeatures)” in “Understanding Your Instrument Panel” for
ment Panel” for further information.
further information.
To Unlock The Doors
Press and release the UNLOCK button on the RKE
transmitter once to unlock the driver’s door or twice to
unlock all doors. The turn signal lamps will flash to
acknowledge the unlock signal. The illuminated entry
system will also turn on.
2
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
To Lock The Doors
Press and release the LOCK button on the RKE transmitter to lock all doors. The turn signal lamps will flash and
the horn will chirp to acknowledge the signal.
Using The Panic Alarm
To turn the Panic Alarm feature on or off, press and hold
the PANIC button on the RKE transmitter for at least one
second and release. When the Panic Alarm is on, the
headlights turn on, the park lamps will flash, the horn
Refer to “Keyless Enter-N-Go” under “Things To Know
will pulse on and off, and the interior lights will turn on.
Before Starting Your Vehicle” for further information.
The Panic Alarm will stay on for three minutes unless
Sound Horn With Remote Key Lock
you turn it off by either pressing the PANIC button a
This feature will cause the horn to chirp when the doors
second time, or drive the vehicle at a speed of 15 mph
are locked with the RKE transmitter or the Passive Entry
(24 km/h) or greater.
feature. The horn chirp feature can be turned on or off. To
change the current setting, refer to “Electronic Vehicle NOTE: The interior lights will turn off if you turn the
Information Center (EVIC)/Personal Settings (Customer- ignition switch to the ACC or ON/RUN position while
Programmable Features)” in “Understanding Your Instru- the Panic Alarm is activated. However, the exterior lamps
ment Panel” for further information.
and horn will remain on.
Programming Additional Transmitters
Programming Key Fobs or RKE transmitters may be
performed at an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
Transmitter Battery Replacement
The recommended replacement battery is one CR2032
battery.
2
NOTE:
• Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
• Do not touch the battery terminals that are on the back
housing or the printed circuit board.
1. Remove the emergency key by sliding the mechanical
latch at the top of the RKE transmitter sideways with
your thumb and then pull the key out with your other
hand.
Emergency Key Removal
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
2. Insert the tip of the emergency key or a #2 flat blade
screwdriver into the slot and gently pry the two halves of
the RKE transmitter apart. Make sure not to damage the
seal during removal.
Separating RKE Transmitter
Inserting Emergency Key Into Slot
3. Remove and replace the battery. When replacing the
battery, match the + sign on the battery to the + sign on
the inside of the battery clip, located on the back cover.
Avoid touching the new battery with your fingers. Skin
oils may cause battery deterioration. If you touch a
battery, clean it with rubbing alcohol.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29
4. To assemble the RKE transmitter case, snap the two If your RKE transmitter fails to operate from a normal
distance, check for these two conditions:
halves together.
General Information
This device complies with part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:
1. A weak battery in the RKE transmitter. The expected
life of the battery is a minimum of three years.
2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, and some mobile or CB radios.
• This device may not cause harmful interference.
REMOTE STARTING SYSTEM — IF EQUIPPED
This system uses the Remote Keyless Entry
(RKE) transmitter to start the engine conveniently from outside the vehicle while still
maintaining security. The system has a range of
NOTE: Changes or modifications not expressly apapproximately
300 ft (91 m).
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
• The vehicle must be equipped with an automatic
transmission to be equipped with Remote Start.
• This device must accept any interference received,
including interference that may cause undesired
operation.
• Obstructions between the vehicle and RKE transmitter
may reduce this range.
2
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
How To Use Remote Start
• System not disabled from previous remote start event
All of the following conditions must be met before the
• Vehicle theft alarm not active
engine will remote start:
• Ignition in Off position for Keyless Enter-N-Go vehicle
• Shift lever in PARK
• Doors closed
WARNING!
• Hood closed
• Do not start or run an engine in a closed garage or
confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious
injury or death when inhaled.
• Keep Remote Keyless Entry (RKE) transmitters
away from children. Operation of the Remote Start
System, windows, door locks or other controls
could cause serious injury or death.
• Liftgate/Flipper Glass closed
• Hazard switch off
• Brake switch inactive (brake pedal not pressed)
• Ignition key removed from ignition switch
• Battery at an acceptable charge level
• RKE PANIC button not pressed
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31
Remote Start Abort Message On Electronic Vehicle To Enter Remote Start Mode
Press and release the REMOTE START button
Information Center (EVIC) — If Equipped
The following messages will display in the EVIC if the
on the RKE transmitter twice within five secvehicle fails to remote start or exits remote start premaonds. The vehicle doors will lock, the parking
turely:
lights will flash and the horn will chirp twice
(if programmed). Then, the engine will start and the
• Remote Start Aborted — Door Ajar
vehicle will remain in the Remote Start mode for a
• Remote Start Aborted — Hood Ajar
15 minute cycle.
• Remote Start Aborted — Liftgate Ajar
• Remote Start Aborted — Fuel Low
• Remote Start Disabled — Start Vehicle To Reset
The EVIC message stays active until the ignition is turned
to the ON/RUN position.
NOTE:
• If an engine fault is present or fuel level is low, the
vehicle will start and then shut down in 10 seconds.
• The park lamps will turn on and remain on during
Remote Start mode.
• For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in
the Remote Start mode.
2
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
• The engine can be started two consecutive times with
the RKE transmitter. However, the ignition must be
cycled by pushing the START/STOP button twice (or
the ignition switch must be cycled to the ON/RUN
position) before you can repeat the start sequence for a
third cycle.
To Exit Remote Start Mode And Drive The Vehicle
Before the end of 15 minute cycle, press and release the
UNLOCK button on the RKE transmitter to unlock the
doors and disarm the Vehicle Security Alarm (if
equipped). Then, prior to the end of the 15 minute cycle,
press and release the START/STOP button. If the
START/STOP button is not present, insert the Key Fob
into the ignition switch and turn the switch to the
ON/RUN position.
To Exit Remote Start Mode Without Driving The
Vehicle
Press and release the REMOTE START button one time or
allow the engine to run for the entire 15 minute cycle.
NOTE:
• For vehicles not equipped with the Keyless EnterNOTE: To avoid unintentional shutdowns, the system
N-Go feature, the ignition switch must be in the
will disable the one time press of the REMOTE START
ON/RUN position in order to drive the vehicle.
button for two seconds after receiving a valid Remote
Start request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33
• For vehicles not equipped with the Keyless EnterN-Go feature, the message “Remote Start Active —
Insert Key and Turn to Run” will display in the EVIC
until you insert the key. Refer to “Electronic Vehicle
Information Center (EVIC)” for further information.
Remote Start Comfort Systems — If Equipped
When remote start is activated, the heated steering
wheel, and driver heated seat features will automatically
turn on in cold weather. In warm weather, the driver
vented seat feature will automatically turn on when the
remote start is activated. These features will stay on
• For vehicles equipped with the Keyless Enter-N-Go
through the duration of remote start or until the ignition
feature, the message “Remote Start Active — Push
switch is turned to the ON/RUN position.
Start Button” will display in the EVIC until you push
the START button.
The Remote Start Comfort System can be activated and
deactivated through the Electronic Vehicle Information
Center (EVIC). For more information on Remote Start
Comfort System operation refer to “Electronic Vehicle
Information Center (EVIC)/Customer-Programmable
Features (SETUP)” in “Understanding Your Instrument
Panel”.
2
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
DOOR LOCKS
Manual Door Locks
The power door locks can be manually locked from
inside the vehicle by using the door lock knob. To lock
each door, push the door lock knob on each door trim
panel downward. To unlock the front doors, pull the
inside door handle to the first detent. To unlock the rear
doors, pull the door lock knob on the door trim panel
upward. If the lock knob is down when the door is
closed, the door will lock. Therefore, make sure the key is
not inside the vehicle before closing the door.
Manual Door Lock Knob
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35
WARNING!
• For personal security and safety in the event of an
accident, lock the vehicle doors when you drive, as
well as when you park and leave the vehicle.
• When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or
others could be seriously or fatally injured. Children should be warned not to touch the parking
brake, brake pedal or the shift lever.
• Do not leave the key fob in or near the vehicle, and
do not leave Keyless Enter-N-Go in the ACC or
ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
Power Door Locks
The power door lock switch is located on each front door
panel. Press the switch to lock or unlock the doors.
2
Power Door Lock Switch
If the lock knob is down when the door is closed, the door
will lock. Therefore, make sure the Key Fob is not inside
the vehicle before closing the door.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
If you press the door lock switch while the Key Fob is in Vehicle Information Center (EVIC)/Personal Settings
the ignition switch and the driver’s door is open, the (Customer-Programmable Features)” in “Understanding
Your Instrument Panel” for further information.
doors will not lock.
If a rear door is locked, it cannot be opened from inside Child-Protection Door Lock System — Rear
the vehicle without first unlocking the door. The door Doors
To provide a safer environment for small children riding
may be unlocked manually by raising the lock knob.
in the rear seats, the rear doors are equipped with
Automatic Door Locks — If Equipped
Child-Protection Door Lock system.
When enabled, the door locks will lock automatically
when the vehicle’s speed exceeds 15 mph (24 km/h). The To Engage Or Disengage The Child-Protection
auto door lock feature can be enabled or disabled by your Door Lock System
authorized dealer per written request of the customer.
1. Open the rear door.
Please see your authorized dealer for service.
2. Insert the tip of the emergency key into the lock and
Automatic Unlock On Exit Feature — If Equipped
rotate to the LOCK or UNLOCK position.
If Auto Unlock is enabled, this feature will unlock all the
doors when the driver’s door is opened if the vehicle is
stopped and in PARK or NEUTRAL. Refer to “Electronic
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37
3. Repeat steps 1 and 2 for the opposite rear door.
2
Child-Protection Door Lock Function
Child-Protection Door Lock Location
WARNING!
Avoid trapping anyone in a vehicle in a collision.
Remember that the rear doors can only be opened
from the outside when the Child-Protection locks are
engaged (locked).
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: For emergency exit with the system engaged,
move the lock knob up (unlocked position), roll down the
window and open the door with the outside door handle.
the handle may time out. Pulling the deactivated front
door handle will reactivate the door handle’s Passive
Entry feature.
• If wearing gloves on your hands, or if it has been
KEYLESS ENTER-N-GO™
raining on the Passive Entry door handle, the unlock
The Passive Entry system is an enhancement to the
sensitivity can be affected, resulting in a slower revehicle’s Remote Keyless Entry (RKE) system and a
sponse time.
feature of Keyless Enter-N-Go™. This feature allows you
to lock and unlock the vehicle’s door(s) without having to • Unlocking the vehicle by RKE transmitter or Keyless
press the RKE transmitter lock or unlock buttons.
Enter-N-Go™ and not opening any door will cause the
doors to ⬙re-lock⬙ and arm theft alarm (if equipped).
NOTE:
• Passive Entry may be programmed ON/OFF; refer to To Unlock From The Driver’s Side:
“Electronic Vehicle Information Center (EVIC)/Personal With a valid Passive Entry RKE transmitter within 5 ft
Settings (Customer-Programmable Features)” in “Under- (1.5 m) of the driver’s door handle, grab the driver’s front
standing Your Instrument Panel” for further information. door handle to unlock the driver’s door automatically.
• If a Passive Entry door handle has not been used for The interior door panel lock knob will raise when the
approximately 72 hours, the Passive Entry feature for door is unlocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39
To Unlock From The Passenger Side:
With a valid Passive Entry RKE transmitter within 5 ft
(1.5 m) of the passenger door handle, grab the front
passenger door handle to unlock all four doors automatically. The interior door panel lock knob will raise when
the door is unlocked.
NOTE: All doors will unlock when the front passenger
door handle is grabbed regardless of the driver’s door
unlock preference setting (“Unlock Driver Door 1st
Press” or “Unlock All Doors 1st Press”).
Grabbing The Driver’s Door Handle
NOTE: If “Unlock All Doors 1st Press” is programmed
all doors will unlock when you grab hold of the driver’s
front door handle. To select between “Unlock Driver
Door 1st Press” and “Unlock All Doors 1st Press”, refer to
“Electronic Vehicle Information Center (EVIC)/Personal
Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
Preventing Inadvertent Locking Of Passive Entry RKE
Transmitter In Vehicle
To minimize the possibility of unintentionally locking a
Passive Entry RKE transmitter inside your vehicle, the
Passive Entry system is equipped with an automatic door
unlock feature which will function if there is no Key Fob
present in the ignition.
2
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
If one of the vehicle doors is open and the door panel
switch is used to lock the vehicle, once all open doors
have been closed the vehicle checks the inside and
outside of the vehicle for any valid Passive Entry RKE
transmitters. If one of the vehicle’s Passive Entry RKE
transmitters is detected inside the vehicle, and no other
valid Passive Entry RKE transmitters are detected outside the vehicle, the Passive Entry System automatically
unlocks all vehicle doors and chirps the horn three times
(on the third attempt ALL doors will lock and the Passive
Entry RKE transmitter can be locked in the vehicle).
To Enter The Liftgate
Liftgate Passive Entry Button
With a valid Passive Entry RKE transmitter within 3 ft
NOTE: If “Unlock All Doors 1st Press” is programmed
(1.0 m) of the liftgate, press the button on the right side of
in EVIC, all doors will unlock when you push the button
the chrome accent bar, which is located on the liftgate
on the liftgate. If ⬙Unlock Driver Door 1st press⬙ is
below the liftgate glass to lock or unlock the vehicle.
programmed in EVIC, the liftgate will unlock when you
press the button on the liftgate. For further information,
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41
refer to “Electronic Vehicle Information Center (EVIC)/ With one of the vehicle’s Passive Entry RKE transmitters
Personal Settings (Customer-Programmable Features)” in within 5 ft (1.5 m) of the driver or passenger front door
“Understanding Your Instrument Panel”.
handle, press the door handle LOCK button to lock all
four doors and liftgate.
To Lock The Vehicle’s Doors
The front door handles have LOCK buttons located on NOTE:
• After pressing the door handle LOCK button, you
the outside of the handles.
must wait two seconds before you can lock or unlock
the doors, using either Passive Entry door handle. This
is done to allow you to check if the vehicle is locked by
pulling the door handle, without the vehicle reacting
and unlocking.
• The Passive Entry system will not operate if the RKE
transmitter battery is dead.
The vehicle doors can also be locked by using the RKE
transmitter lock button or the lock button located on the
vehicle’s interior door panel.
Outside Door Handle Lock Button
2
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WINDOWS
Power Windows
The power window controls are located on the driver’s
door trim panel. There is a single switch on the front
passenger door/rear doors which operates the front
passenger/rear passenger door windows. The window
controls will operate only when the ignition switch is in
the ON/RUN or ACCESSORY position.
Power Window Switches
The power window switches remain active for up to
10 minutes after the ignition switch has been turned OFF.
Opening a vehicle front door will cancel this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43
Auto-Down
Both the driver and front passenger window switches
have an “Auto-Down” feature. Press the window switch
past the first detent, release, and the window will go
down automatically. To cancel the “Auto-Down” movement, operate the switch in either the up or down
direction and release the switch.
To stop the window from going all the way up during the
Auto Up operation, push down on the switch briefly.
To close the window part way, lift the window switch to
the first detent and release when you want the window to
stop.
NOTE: If the window runs into any obstacle during
Auto Up it will reverse direction and then go back down.
To open the window part way, press to the first detent
Remove the obstacle and use the window switch again to
and release it when you want the window to stop.
close the window. Any impact due to rough road condiThe power window switches remain active for 10 min- tions may trigger the auto reverse function unexpectedly
utes after the ignition has been turned OFF. Opening during Auto Up. If this happens, pull the switch lightly to
the first detent and hold it to close the window manually.
either front door will cancel this feature.
Auto Up Feature With Anti-Pinch Protection —
Driver And Front Passenger Door Only
Lift the window switch fully upward to the second
detent, release, and the window will go up automatically.
WARNING!
There is no anti-pinch protection when the window
is almost closed. Be sure to clear all objects from the
window before closing.
2
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Resetting The Auto Up Feature
Should the Auto Up feature stop working, the window
probably needs to be reset. To reset Auto Up:
1. Pull the window switch up to close the window
completely and continue to hold the switch up for an
additional two seconds after the window is closed.
2. Push the window switch down firmly to the second
detent to open the window completely and continue to
hold the switch down for an additional two seconds after
the window is fully open.
Window Lockout Button
The Window Lockout button on the driver’s door allows
you to disable the window controls on the rear doors. To
disable the window controls on the rear doors, press the
Window Lockout button. To enable the window controls,
press the Window Lockout button again.
Window Lockout Button
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45
Wind Buffeting
Wind buffeting can be described as the perception of
pressure on the ears or a helicopter-type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the sunroof (if equipped) in certain
open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with
the sunroof open, adjust the sunroof opening to minimize
the buffeting.
LIFTGATE
To open the liftgate, pull up on the handle and lift.
Manually unlocking the vehicle doors with the plunger
or a key in the lock cylinder will not unlock the liftgate.
2
Liftgate Release
WARNING!
Driving with the liftgate open can allow poisonous
exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the
liftgate closed when you are operating the vehicle.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Power Liftgate — If Equipped
The power liftgate may be opened by pulling
up on the liftgate handle or by pressing the
LIFTGATE button on the Remote Keyless Entry
(RKE) transmitter. Press the LIFTGATE button
on the RKE transmitter twice within five seconds, to open
the power liftgate. Once the liftgate is open, pressing the
button twice within five seconds a second time will close
the liftgate. The power liftgate may also be opened and
closed with the overhead console switch.
When the LIFTGATE button on the RKE transmitter is
pressed two times, the turn signals will flash twice to
signal that the liftgate is opening or closing (if Flash
Lamps with Lock is enabled in the EVIC) and the liftgate
chime will be audible. For further information, refer to
“Customer-Programmable Features (System Setup)/
Electronic Vehicle information Center (EVIC)” in “Understanding Your Instrument Panel”.
NOTE: In the event of a power malfunction to the
liftgate, an emergency liftgate latch release can be used to
Also, the power liftgate may be closed by pressing the open the liftgate. The emergency liftgate latch release can
liftgate switch located on the left rear trim, near the be accessed through a snap-in cover located on the
liftgate opening. Pressing once will close the liftgate only. liftgate trim panel.
This button cannot be used to open the liftgate.
To operate the power liftgate manually in the open
direction, pull the liftgate handle once to initiate power
cycle and then pull the handle a second time to put
liftgate into manual mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47
WARNING!
During power operation, personal injury or cargo
damage may occur. Ensure the liftgate travel path is
clear. Make sure the liftgate is closed and latched
before driving away.
button to operate. If the liftgate is not fully open, press
the Liftgate button on the Key Fob to fully open the
liftgate, and then press it again to close.
• If the liftgate handle is pulled while the power liftgate
is closing, the liftgate will reverse to the full open
position.
• If the liftgate handle is pulled while the power liftgate
NOTE:
is opening, the liftgate motor will disengage to allow
• If anything obstructs the power liftgate while it is
manual operation.
closing or opening, the liftgate will automatically
reverse to the closed or open position, provided it
• The power liftgate buttons will not operate if the
meets sufficient resistance.
vehicle is in gear or the vehicle speed is above 0 mph
(0 km/h).
• There are also pinch sensors attached to the side of the
liftgate. Light pressure anywhere along these strips
• The power liftgate will not operate in temperatures
will cause the liftgate to return to the open position.
below ⫺22°F (⫺30°C) or temperatures above 150°F
(65°C). Be sure to remove any buildup of snow or ice
• The power liftgate must be in the full open position for
from the liftgate before pressing any of the power
rear liftgate close button or overhead console close
liftgate switches.
2
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
• If the power liftgate encounters multiple obstructions
within the same cycle, the system will automatically
stop and the liftgate must be opened or closed manually.
WARNING! (Continued)
• If you are required to drive with the liftgate open,
make sure that all windows are closed, and the
climate control blower switch is set at high speed.
Do not use the recirculation mode.
• If your liftgate is power closing and you put the
vehicle in gear, the liftgate will continue to power
close. However, vehicle movement may result in a Gas props support the liftgate in the open position.
detection of an obstruction.
However, because the gas pressure drops with temperature, it may be necessary to assist the props when
WARNING!
opening the liftgate in cold weather.
• Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your
passengers could be injured by these fumes. Keep
the liftgate closed when you are operating the
vehicle.
(Continued)
OCCUPANT RESTRAINTS
Some of the most important safety features in your
vehicle are the restraint systems:
• Three-point lap and shoulder belts for the driver and
all passengers
• Advanced Front Air Bags for driver and front passenger
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49
• Supplemental Active Head Restraints (AHR) located
on top of the front seats (integrated into the head
restraint)
way out and then adjusting the belt to the desired
length to restrain a child seat or secure a large item in
a seat — if equipped
• Supplemental Side Air Bag Inflatable Curtains Please pay close attention to the information in this
(SABIC) for the driver and passengers seated next to a section. It tells you how to use your restraint system
properly, to keep you and your passengers as safe as
window
possible.
• Supplemental Seat-Mounted Side Air Bags (SAB)
If you will be carrying children too small for adult-sized
• An energy-absorbing steering column and steering
seat belts, the seat belts or the Lower Anchors and Tether
wheel
for CHildren (LATCH) feature also can be used to hold
infant and child restraint systems. For more information
• Knee bolsters for front seat occupants
on LATCH, refer to Lower Anchors and Tether for
• Front seat belts incorporate pretensioners that may
CHildren (LATCH).
enhance occupant protection by managing occupant
NOTE: The Advanced Front Air Bags have a multistage
energy during an impact event
inflator design. This allows the air bag to have different
• All seat belt systems (except the driver) include Autorates of inflation based on several factors, including the
matic Locking Retractors (ALRs), which lock the seat
severity and type of collision.
belt webbing into position by extending the belt all the
2
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Here are some simple steps you can take to minimize the ride properly buckled up in the rear seat. Never allow
risk of harm from a deploying air bag:
children to slide the shoulder belt behind them or under
their arm.
1. Children 12 years old and under should always ride
buckled up in a rear seat.
If a child from 1 to 12 years old (not in a rear facing child
seat) must ride in the front passenger seat, move the seat
WARNING!
as far back as possible and use the proper child restraint.
(Refer to “Child Restraints”)
Infants in rear facing child restraints should never
ride in the front seat of a vehicle with a passenger You should read the instructions provided with your
Advanced Front Air Bag. An air bag deployment can child restraint to make sure that you are using it properly.
cause severe injury or death to infants in that posi2. All occupants should always wear their lap and
tion.
shoulder belts properly.
Children that are not big enough to wear the vehicle seat 3. The driver and front passenger seats should be
belt properly (see section on Child Restraints) should be moved back as far as practical to allow the Advanced
secured in the rear seat in child restraints or belt- Front Air Bags room to inflate.
positioning booster seats. Older children who do not use
child restraints or belt-positioning booster seats should
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51
4. Do not lean against the door or window. If your
vehicle has side air bags, and deployment occurs, the
side air bags will inflate forcefully into the space
between you and the door.
5. If the air bag system in this vehicle needs to be
modified to accommodate a disabled person, contact
the Customer Center. Phone numbers are provided
under ⴖIf You Need Assistanceⴖ.
WARNING!
• Relying on the air bags alone could lead to more
severe injuries in a collision. The air bags work
with your seat belt to restrain you properly. In
some collisions, the air bags won’t deploy at all.
Always wear your seat belts even though you have
air bags.
(Continued)
WARNING! (Continued)
• Being too close to the steering wheel or instrument
panel during Advanced Front Air Bag deployment
could cause serious injury, including death. Air
Bags need room to inflate. Sit back, comfortably
extending your arms to reach the steering wheel or
instrument panel.
• Supplemental Side Air Bag Inflatable Curtain
(SABIC) and Seat-Mounted Side Air Bags (SAB)
also need room to inflate. Do not lean against the
door or window. Sit upright in the center of the
seat.
• In a collision, you and your passengers can suffer
much greater injuries if you are not properly
buckled up. You can strike the interior of your
vehicle or other passengers, or you can be thrown
out of the vehicle. Always be sure you and others
in your vehicle are buckled up properly.
2
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Buckle up even though you are an excellent driver, even
on short trips. Someone on the road may be a poor driver
and cause a collision that includes you. This can happen
far away from home or on your own street.
Research has shown that seat belts save lives, and they
can reduce the seriousness of injuries in a collision. Some
of the worst injuries happen when people are thrown
from the vehicle. Seat belts reduce the possibility of
ejection and the risk of injury caused by striking the
inside of the vehicle. Everyone in a motor vehicle should
be belted at all times.
Lap/Shoulder Belts
All seating positions in your vehicle are equipped with
lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions.
This feature allows the shoulder part of the belt to move
freely with you under normal conditions. However, in a
collision the belt will lock and reduce the risk of you
striking the inside of the vehicle or being thrown out.
WARNING!
• Wearing a seat belt incorrectly is dangerous. Seat
belts are designed to go around the large bones of
your body. These are the strongest parts of your
body and can take the forces of a collision the best.
Wearing your belt in the wrong place could make
your injuries in a collision much worse. You might
suffer internal injuries, or you could even slide out
of part of the belt. Follow these instructions to
wear your seat belt safely and to keep your passengers safe, too.
• Two people should never be belted into a single
seat belt. People belted together can crash into one
another in a collision, hurting one another badly.
Never use a lap/shoulder belt or a lap belt for more
than one person, no matter what their size.
(Continued)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53
WARNING! (Continued)
• It is dangerous to ride in a cargo area, inside or
outside of a vehicle. In a collision, people riding in
these areas are more likely to be seriously injured
or killed.
• Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat
belts.
• Be sure everyone in your vehicle is in a seat and
using a seat belt properly.
2. The seat belt latch plate is above the back of your seat.
Grasp the latch plate and pull out the belt. Slide the latch
plate up the webbing as far as necessary to make the belt
go around your lap.
Lap/Shoulder Belt Operating Instructions
1. Enter the vehicle and close the door. Sit back and
adjust the seat.
Latch Plate
2
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3. When the belt is long enough to fit, insert the latch
plate into the buckle until you hear a “click.”
WARNING!
• A belt that is buckled into the wrong buckle will
not protect you properly. The lap portion could
ride too high on your body, possibly causing
internal injuries. Always buckle your belt into the
buckle nearest you.
• A belt that is too loose will not protect you
properly. In a sudden stop you could move too far
forward, increasing the possibility of injury. Wear
your seat belt snugly.
(Continued)
Latch Plate to Buckle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55
WARNING! (Continued)
• A belt that is worn under your arm is dangerous.
Your body could strike the inside surfaces of the
vehicle in a collision, increasing head and neck
injury. A belt worn under the arm can cause
internal injuries. Ribs aren’t as strong as shoulder
bones. Wear the belt over your shoulder so that
your strongest bones will take the force in a
collision.
• A shoulder belt placed behind you will not protect
you from injury during a collision. You are more
likely to hit your head in a collision if you do not
wear your shoulder belt. The lap and shoulder belt
are meant to be used together.
4. Position the lap belt across your thighs, below your
abdomen. To remove slack in the lap portion, pull up a
bit on the shoulder belt. To loosen the lap belt if it is too
tight, tilt the latch plate and pull on the lap belt. A snug
belt reduces the risk of sliding under the belt in a
collision.
WARNING!
• A lap belt worn too high can increase the risk of
injury in a collision. The belt forces won’t be at the
strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt
as low as possible and keep it snug.
• A twisted belt may not protect you properly. In a
collision, it could even cut into you. Be sure the
belt is straight. If you can’t straighten a belt in
your vehicle, take it to your authorized dealer
immediately and have it fixed.
2
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
5. Position the shoulder belt on your chest so that it is 6. To release the belt, push the red button on the buckle.
comfortable and not resting on your neck. The retractor The belt will automatically retract to its stowed position.
will withdraw any slack in the belt.
If necessary, slide the latch plate down the webbing to
allow it to retract fully.
WARNING!
A frayed or torn belt could rip apart in a collision and
leave you with no protection. Inspect the belt system
periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do not
disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have
been damaged (bent retractor, torn webbing, etc.).
Removing Slack From Belt
Lap/Shoulder Belt Untwisting Procedure
Use the following procedure to untwist a twisted lap/
shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57
1. Position the latch plate as close as possible to the
anchor point.
2. At about 6 to 12 in (15 to 30 cm) above the latch plate,
grasp and twist the belt webbing 180 degrees to create a
fold that begins immediately above the latch plate.
2
3. Slide the latch plate upward over the folded webbing.
The folded webbing must enter the slot at the top of the
latch plate.
4. Continue to slide the latch plate up until it clears the
folded webbing.
Adjustable Upper Shoulder Belt Anchorage
In the front seating positions, the shoulder belt can be
adjusted upward or downward to position the belt away
from your neck. Press the release button to release the
anchorage, and then move it up or down to the position
that fits you best.
Adjusting Upper Shoulder Belt
As a guide, if you are shorter than average, you will
prefer a lower position, and if you are taller than average,
you will prefer a higher position. When you release the
anchorage, try to move it up or down to make sure that
it is locked in position.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: The adjustable upper shoulder belt anchorage is
equipped with an Easy Up feature. This feature allows
the shoulder belt anchorage to be adjusted in the upward
position without pushing the release button. To verify the
shoulder belt anchorage is latched, pull downward on
the shoulder belt anchorage until it is locked into
position.
Seat Belts In Passenger Seating Positions
The seat belts in the passenger seating positions are
equipped with Automatic Locking Retractors (ALR)
which are used to secure a child restraint system. For
additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt” under the “Child
Restraints” section. The chart below defines the type of
feature for each seating position.
First Row
Second Row
— Captains
Chair
Second Row
— Bench
Third Row
Driver
N/A
ALR
Center
N/A
N/A
Passenger
ALR
ALR
ALR
ALR
ALR
ALR
N/A
ALR
• N/A — Not Applicable
• ALR — Automatic Locking Retractor
If the passenger seating position is equipped with an
ALR and is being used for normal usage:
Only pull the belt webbing out far enough to comfortably
wrap around the occupant’s mid-section so as to not
activate the ALR. If the ALR is activated, you will hear a
ratcheting sound as the belt retracts. Allow the webbing
to retract completely in this case and then carefully pull
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59
out only the amount of webbing necessary to comfort- 3. Allow the belt to retract. As the belt retracts, you will
ably wrap around the occupant’s mid-section. Slide the hear a clicking sound. This indicates the safety belt is
now in the Automatic Locking Mode.
latch plate into the buckle until you hear a ⬙click.⬙
Automatic Locking Retractor Mode (ALR) —
If Equipped
In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in
the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions with a combination lap/shoulder belt. Use the Automatic Locking Mode
anytime a child safety seat is installed in a seating
position that has a belt with this feature. Children
12 years old and under should always be properly
restrained in the rear seat.
How To Engage The Automatic Locking Mode
1. Buckle the combination lap and shoulder belt.
2. Grasp the shoulder portion and pull downward until
the entire belt is extracted.
How To Disengage The Automatic Locking Mode
Unbuckle the combination lap/shoulder belt and allow it
to retract completely to disengage the Automatic Locking
Mode and activate the vehicle sensitive (emergency)
locking mode.
WARNING!
• The belt and retractor assembly must be replaced
if the seat belt assembly Automatic Locking Retractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual.
• Failure to replace the belt and retractor assembly
could increase the risk of injury in collisions.
2
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Energy Management Feature
This vehicle has a safety belt system with an Energy
Management feature in the front seating positions to help
further reduce the risk of injury in the event of a head-on
collision.
Seat Belt Pretensioners
The seat belts for both front seating positions are
equipped with pretensioning devices that are designed to
remove slack from the seat belt in the event of a collision.
These devices may improve the performance of the seat
This safety belt system has a retractor assembly that is belt by assuring that the belt is tight about the occupant
designed to release webbing in a controlled manner. This early in a collision. Pretensioners work for all size occupants, including those in child restraints.
feature is designed to help reduce the belt force acting on
the occupant’s chest.
NOTE: These devices are not a substitute for proper seat
belt placement by the occupant. The seat belt still must be
WARNING!
worn snugly and positioned properly.
• The belt and retractor assembly must be replaced
if the seat belt assembly Automatic Locking Retractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual.
• Failure to replace the belt and retractor assembly
could increase the risk of injury in collisions.
The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the air bags, the pretensioners are single use items. A deployed pretensioner or
a deployed air bag must be replaced immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61
Supplemental Active Head Restraints (AHR)
These head restraints are passive, deployable components, and vehicles with this equipment cannot be readily
identified by any markings, only through visual inspection of the head restraint. The head restraint will be split
in two halves, with the front half being soft foam and
trim, the back half being decorative plastic.
How The Active Head Restraints (AHR) Work
The Occupant Restraint Controller (ORC) determines
whether the severity, or type of rear impact will require
the Active Head Restraints (AHR) to deploy. If a rear
impact requires deployment, both the driver and front
passenger seat AHRs will be deployed.
When AHRs deploy during a rear impact, the front half
of the head restraint extends forward to minimize the gap
between the back of the occupant’s head and the AHR.
This system is designed to help prevent or reduce the
extent of injuries to the driver and front passenger in
certain types of rear impacts.
2
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: The Active Head Restraints (AHR) may or may
not deploy in the event of a front or side impact.
However if during a front impact, a secondary rear
impact occurs, the AHR may deploy based on several
factors, including the severity and type of the impact.
Active Head Restraint (AHR) Components
1 — Head Restraint Front
Half (Soft Foam and Trim)
2 — Seatback
3 — Head Restraint Back Half
(Decorative Plastic Rear Cover)
4 — Head Restraint Guide
Tubes
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63
CAUTION!
1. Grasp the deployed AHR from the rear seat.
All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head
restraints are placed in their proper positions in order
to minimize the risk of neck injury in the event of a
collision.
NOTE: For more information on properly adjusting and
positioning the head restraint, refer to “Adjusting Active
Head Restraints” in “Understanding The Features Of
Your Vehicle”.
Resetting Active Head Restraints (AHR)
Hand Positioning Points On AHR
If the Active Head Restraints are triggered in a collision,
you must reset the head restraint on the driver’s and 2. Position the hands on the top of the deployed AHR at
front passenger seat. You can recognize when the Active a comfortable position.
Head Restraint has been triggered by the fact that they
have moved forward (as shown in step three of the
resetting procedure).
2
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3. Pull down then rearward towards the rear of the
vehicle then down to engage the locking mechanism.
3 — Final Downward Movement To Engage Locking Mechanism
1 — Downward Movement
2 — Rearward Movement
4. The AHR front soft foam and trim half should lock
into the back decorative plastic half.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65
Enhanced Seat Belt Use Reminder System
(BeltAlert姞)
BeltAlert威 is a feature intended to remind the driver and
front passenger (if equipped with front passenger
BeltAlert威) to fasten their seat belts. The feature is active
whenever the ignition is on. If the driver or front seat
passenger is unbelted, the Seat Belt Reminder Light will
turn on and remain on until both front seat belts are
fastened.
The BeltAlert威 warning sequence begins after the vehicle
speed is over 5 mph (8 km/h), by blinking the Seat Belt
Reminder Light and sounding an intermittent chime.
AHR In Reset Position
Once the sequence starts, it will continue for the entire
NOTE:
duration or until the respective seatbelts are fastened.
• If you have difficulties or problems resetting the
After the sequence completes, the Seat Belt Reminder
Active Head Restraints, see an authorized dealer.
Light remains illuminated until the respective seat belts
• For safety reasons, have the Active Head Restraints are fastened. The driver should instruct all other occuchecked by a qualified specialist at an authorized pants to fasten their seat belts. If a front seat belt is
dealer.
2
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
unbuckled while traveling at speeds greater than 5 mph Seat Belts And Pregnant Women
(8 km/h), BeltAlert威 will provide both audio and visual We recommend that pregnant women use the seat belts
throughout their pregnancy. Keeping the mother safe is
notification.
the best way to keep the baby safe.
The front passenger seat BeltAlert威 is not active when the
front passenger seat is unoccupied. BeltAlert威 may be Pregnant women should wear the lap part of the belt
triggered when an animal or heavy object is on the front across the thighs and as snug across the hips as possible.
passenger seat or when the seat is folded flat (if Keep the belt low so that it does not come across the
equipped). It is recommended that pets be restrained in abdomen. That way the strong bones of the hips will take
the rear seat in pet harnesses or pet carriers that are the force if there is a collision.
secured by seat belts, and cargo is properly stowed.
Seat Belt Extender
BeltAlert威 can be enabled or disabled by your authorized If a seat belt is too short, even when fully extended and
dealer. Chrysler Group LLC does not recommend deac- when the adjustable upper shoulder belt anchorage (if
equipped) is in its lowest position, your authorized
tivating BeltAlert威.
dealer can provide you with a seat belt extender. This
NOTE: Although BeltAlert威 has been deactivated, the
extender should be used only if the existing belt is not
Seat Belt Reminder Light will continue to illuminate
long enough. When it is not required, remove the exwhile the driver’s or front passenger (if equipped with
tender and store it.
BeltAlert威) seat belt remains unfastened.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67
WARNING!
Using a seat belt extender when not needed can
increase the risk of injury in a collision. Only use
when the lap belt is not long enough when it is worn
low and snug, and in the recommended seating
positions. Remove and store the extender when not
needed.
Supplemental Restraint System (SRS) — Air Bags
This vehicle has Advanced Front Air Bags for both the
driver and front passenger as a supplement to the seat
Advanced Front Air Bag And Knee Bolster Locations
belt restraint systems. The driver’s Advanced Front Air
Bag is mounted in the center of the steering wheel. The 1 — Driver And Passenger Advanced Front Air Bags
passenger’s Advanced Front Air Bag is mounted in the 2 — Knee Bolster
instrument panel, above the glove compartment. The NOTE: The Driver and Front Passenger Advanced Front
words SRS AIRBAG are embossed on the air bag covers. Air Bags are certified to the new Federal regulations for
Advanced Air Bags.
2
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The Advanced Front Air Bags have a multistage inflator
design. This allows the air bag to have different rates of
inflation based on several factors, including the severity
and type of collision.
This vehicle is equipped with Supplemental SeatMounted Side Air Bags (SAB) to provide enhanced
protection for an occupant during a side impact. The
Supplemental Seat-Mounted Side Air Bags are located in
the outboard side of the front seats.
This vehicle may be equipped with driver and/or front
passenger seat track position sensors that may adjust the NOTE:
inflation rate of the Advanced Front Air Bags based upon • Air Bag covers may not be obvious in the interior trim,
but they will open during air bag deployment.
seat position.
This vehicle may be equipped with a driver and/or front • After any accident, the vehicle should be taken to an
authorized dealer immediately.
passenger seat belt buckle switch that detects whether
the driver or front passenger seat belt is fastened. The
Air Bag System Components
seat belt buckle switch may adjust the inflation rate of the
Your vehicle may be equipped with the following air bag
Advanced Front Air Bags.
system components:
This vehicle is equipped with Supplemental Side Air Bag
• Occupant Restraint Controller (ORC)
Inflatable Curtains (SABIC) to protect the driver, front,
and rear passengers sitting next to a window. The SABIC • Air Bag Warning Light
air bags, are located above the side windows and their
• Steering Wheel and Column
covers are also labeled: SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69
• Instrument Panel
• Knee Impact Bolster
• Driver Advanced Front Air Bag
• Passenger Advanced Front Air Bag
• Supplemental Seat-Mounted Side Air Bags (SAB)
Advanced Front Air Bag Features
The Advanced Front Air Bag system has multistage
driver and front passenger air bags. This system provides
output appropriate to the severity and type of collision as
determined by the Occupant Restraint Controller (ORC),
which may receive information from the front impact
sensors.
• Supplemental Side Air Bag Inflatable Curtains The first stage inflator is triggered immediately during an
(SABIC)
impact that requires air bag deployment. This low output
is used in less severe collisions. A higher energy output is
• Front and Side Impact Sensors
used for more severe collisions.
• Front Seat Belt Pretensioners, Seat Belt Buckle Switch,
and Seat Track Position Sensors
2
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
• No objects should be placed over or near the air
bag on the instrument panel, because any such
objects could cause harm if the vehicle is in a
collision severe enough to cause the air bag to
inflate.
• Do not put anything on or around the air bag
covers or attempt to open them manually. You may
damage the air bags and you could be injured
because the air bags may no longer be functional.
The protective covers for the air bag cushions are
designed to open only when the air bags are
inflating.
• Do not drill, cut or tamper with the knee bolster in
any way.
• Do not mount any accessories to the knee bolster
such as alarm lights, stereos, citizen band radios,
etc.
Supplemental Seat-Mounted Side Air Bags (SAB)
Supplemental Seat-Mounted Side Air Bags (SAB) may
provide enhanced protection to help protect an occupant
during a side impact. The SAB is marked with an air bag
label sewn into the outboard side of the front seats.
Supplemental Seat-Mounted Side Air Bag Label
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71
When the air bag deploys, it opens the seam between the
front and side of the seat’s trim cover. Each air bag
deploys independently; a left side impact deploys the left
air bag only and a right-side impact deploys the right air
bag only.
Supplemental Side Air Bag Inflatable Curtain
(SABIC)
SABIC air bags may offer side-impact and vehicle rollover protection to front and rear seat outboard occupants
in addition to that provided by the body structure. Each
air bag features inflated chambers placed adjacent to the
head of each outboard occupant that reduce the potential
Supplemental Side Air Bag Inflatable
for side-impact head injuries. The SABIC deploy downCurtain (SABIC) Location
ward, covering both windows on the impact side.
NOTE:
• Should a vehicle rollover occur, the pretensioners
and/or SAB and SABIC air bags on both sides of the
vehicle may deploy.
2
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
• Air Bag covers may not be obvious in the interior trim,
but they will open during air bag deployment.
• Being too close to the SAB and SABIC air bags during
deployment could cause you to be severely injured or
killed.
The system includes side impact sensors that are calibrated to deploy the SAB and SABIC air bags during
impacts that require side air bag occupant protection.
WARNING!
• If your vehicle is equipped with left and right
Supplemental Side Air Bag Inflatable Curtain
(SABIC), do not stack luggage or other cargo up
high enough to block the location of the SABIC.
The area where the SABIC is located should remain free from any obstructions.
WARNING! (Continued)
• Do not use accessory seat covers or place objects
between you and the side air bags; the performance could be adversely affected and/or objects
could be pushed into you, causing serious injury.
• If your vehicle is equipped with SABIC air bags,
do not have any accessory items installed which
will alter the roof, including adding a sunroof to
your vehicle. Do not add roof racks that require
permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof
of the vehicle for any reason.
Knee Impact Bolsters
The Knee Impact Bolsters help protect the knees of the
driver and the front passenger, and position front occupants for the best interaction with the Advanced Front
(Continued) Air Bags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73
Along with seat belts and pretensioners, Advanced Front
Air Bags work with the knee bolsters to provide improved protection for the driver and front passenger. Side
air bags also work with seat belts to improve occupant
protection.
Air Bag Deployment Sensors And Controls
Advanced Front Air Bags are designed to provide additional protection by supplementing the seat belts in
certain frontal collisions depending on several factors,
including the severity and type of collision. Advanced
Front Air Bags are not expected to reduce the risk of
injury in rear, side, or rollover collisions.
The Advanced Front Air Bags will not deploy in all
Occupant Restraint Controller (ORC)
frontal collisions, including some that may produce subThe ORC is part of a Federally regulated safety system
stantial vehicle damage — for example, some pole collirequired for this vehicle.
sions, truck underrides, and angle offset collisions. On
The ORC determines if deployment of the front and/or the other hand, depending on the type and location of
side air bags in a frontal or side collision is required. impact, Advanced Front Air Bags may deploy in crashes
Based on the impact sensor’s signals, a central electronic with little vehicle front-end damage but that produce a
ORC deploys the Advanced Front Air Bags, SABIC air severe initial deceleration.
bags, Supplemental Seat-Mounted Side Air Bags, and
The side air bags will not deploy in all side collisions.
front seat belt pretensioners, as required, depending on
Side air bag deployment will depend on the severity and
several factors, including the severity and type of impact.
type of collision.
2
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Also, the ORC turns on the Air Bag Warning
Light in the instrument panel for approximately four to eight seconds for a self-check
when the ignition is first turned on. After the
self-check, the Air Bag Warning Light will turn off. If the
Seat belts are necessary for your protection in all colliORC detects a malfunction in any part of the system, it
sions, and also are needed to help keep you in position,
turns on the Air Bag Warning Light, either momentarily
away from an inflating air bag.
or continuously. A single chime will sound if the light
The ORC monitors the readiness of the electronic parts of comes on again after initial startup.
the air bag system whenever the ignition switch is in the
It also includes diagnostics that will illuminate the instruSTART or ON/RUN position. If the key is in the OFF
ment cluster Air Bag Warning Light if a malfunction is
position, in the ACC position, or not in the ignition, the
noted that could affect the air bag system. The diagnosair bag system is not on and the air bags will not inflate.
tics also record the nature of the malfunction.
The ORC contains a backup power supply system that
may deploy the air bags even if the battery loses power or
it becomes disconnected prior to deployment.
Because air bag sensors measure vehicle deceleration
over time, vehicle speed and damage by themselves are
not good indicators of whether or not an air bag should
have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75
WARNING!
Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags
to protect you in a collision. If the light does not come
on as a bulb check when the ignition is first turned
on, stays on after you start the vehicle, or if it comes
on as you drive, have an authorized dealer service the
air bag system immediately.
Driver And Passenger Advanced Front Air Bag
Inflator Units
The Driver and Passenger Advanced Front Air Bag
Inflator Units are located in the center of the steering
wheel and on the right side of the instrument panel.
When the ORC detects a collision requiring the Advanced Front Air Bags, it signals the inflator units. A large
quantity of non-toxic gas is generated to inflate the
Advanced Front Air Bags. Different air bag inflation rates
are possible, based on the collision type and severity. The
steering wheel hub trim cover and the upper right side of
the instrument panel separate and fold out of the way as
the air bags inflate to their full size. The air bags fully
inflate in about 50 to 70 milliseconds. This is about half of
the time it takes to blink your eyes. The air bags then
quickly deflate while helping to restrain the driver and
front passenger.
The Advanced Front Air Bag gas is vented through the
vent holes in the sides of the air bag. In this way, the air
bags do not interfere with your control of the vehicle.
Supplemental Seat-Mounted Side Air Bag (SAB)
Inflator Units
The Supplemental Seat-Mounted Side Air Bags are designed to activate only in certain side collisions.
The ORC determines if a side collision requires the side
air bags to inflate, based on several factors, including the
severity and type of collision.
2
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Based on several factors, including the severity and type
of collision, the side air bag inflator on the crash side of
the vehicle may be triggered, releasing a quantity of
non-toxic gas. The inflating SAB exits through the seat
seam into the space between the occupant and the door.
The SAB fully inflate in about 10 milliseconds. The side
air bag moves at a very high speed and with such a high
force that it could injure you if you are not seated
properly, or if items are positioned in the area where the
side air bag inflates. This especially applies to children.
A quantity of non-toxic gas is generated to inflate the
SABIC. The inflating SABIC pushes the outside edge of
the headliner out of the way and covers the window. The
SABIC inflates in about 30 milliseconds (about onequarter of the time that it takes to blink your eyes) with
enough force to injure you if you are not belted and
seated properly, or if items are positioned in the area
where the SABIC inflates. This especially applies to
children. The SABIC is only about 3-1/2 in (9 cm) thick
when it is inflated.
Supplemental Side Air Bag Inflatable Curtain
(SABIC) Inflator Units
During collisions where the impact is confined to a
particular area of the side of the vehicle, the ORC may
deploy the SABIC air bags, depending on several factors,
including the severity and type of collision. In these
events, the ORC will deploy the SABIC only on the
impact side of the vehicle.
Because air bag sensors estimate deceleration over time,
vehicle speed and damage are not good indicators of
whether or not an air bag should have deployed.
NOTE: In a rollover the pretensioners and/or SAB and
SABIC air bags may deploy on both sides of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77
Front And Side Impact Sensors
• Turn on the interior lights, which remain on as long as
In front and side impacts, front and side impact sensors
the battery has power or until the ignition key is
can aid the ORC in determining the appropriate response
removed.
to certain impact events.
• Unlock the doors automatically.
Enhanced Accident Response System
In order to reset the Enhanced Accident Response System
In the event of an impact causing air bag deployment, if
functions after an event, the ignition switch must be
the communication network remains intact, and the
changed from IGN ON to IGN OFF.
power remains intact, depending on the nature of the
event the ORC will determine whether to have the If A Deployment Occurs
Enhanced Accident Response System perform the follow- The Advanced Front Air Bags are designed to deflate
immediately after deployment.
ing functions:
• Cut off fuel to the engine.
NOTE: Front and/or side air bags will not deploy in all
collisions. This does not mean something is wrong with
• Flash hazard lights as long as the battery has power or
the air bag system.
until the ignition key is turned off.
2
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
If you do have a collision which deploys the air bags, any
or all of the following may occur:
throat irritation, move to fresh air. If the irritation
continues, see your doctor. If these particles settle on
your clothing, follow the garment manufacturer’s instructions for cleaning.
• The nylon air bag material may sometimes cause
abrasions and/or skin reddening to the driver and
front passenger as the air bags deploy and unfold. The Do not drive your vehicle after the air bags have deabrasions are similar to friction rope burns or those ployed. If you are involved in another collision, the air
you might get sliding along a carpet or gymnasium bags will not be in place to protect you.
floor. They are not caused by contact with chemicals.
WARNING!
They are not permanent and normally heal quickly.
However, if you haven’t healed significantly within a
Deployed air bags and seat belt pretensioners cannot
few days, or if you have any blistering, see your doctor
protect you in another collision. Have the air bags,
immediately.
seat belt pretensioners, and the front seat belt retrac• As the air bags deflate, you may see some smoke-like tor assemblies replaced by an authorized dealer imparticles. The particles are a normal by-product of the mediately. Also, have the Occupant Restraint Conprocess that generates the non-toxic gas used for air troller (ORC) system serviced as well.
bag inflation. These airborne particles may irritate the
skin, eyes, nose, or throat. If you have skin or eye
irritation, rinse the area with cool water. For nose or
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79
Maintaining Your Air Bag System
WARNING! (Continued)
WARNING!
• Modifications to any part of the air bag system
could cause it to fail when you need it. You could
be injured if the air bag system is not there to
protect you. Do not modify the components or
wiring, including adding any kind of badges or
stickers to the steering wheel hub trim cover or the
upper right side of the instrument panel. Do not
modify the front bumper, vehicle body structure,
or add aftermarket side steps or running boards.
• It is dangerous to try to repair any part of the air
bag system yourself. Be sure to tell anyone who
works on your vehicle that it has an air bag system.
(Continued)
• Do not attempt to modify any part of your air bag
system. The air bag may inflate accidentally or may
not function properly if modifications are made.
Take your vehicle to an authorized dealer for any
air bag system service. If your seat, including your
trim cover and cushion, needs to be serviced in any
way (including removal or loosening/tightening of
seat attachment bolts), take the vehicle to your
authorized dealer. Only manufacturer approved
seat accessories may be used. If it is necessary to
modify the air bag system for persons with disabilities, contact your authorized dealer.
2
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Air Bag Warning Light
You will want to have the air bags ready to
inflate for your protection in a collision. The
Air Bag Warning Light monitors the internal
circuits and interconnecting wiring associated
with air bag system electrical components. While the air
bag system is designed to be maintenance free, if any of
the following occurs, have an authorized dealer service
the air bag system immediately.
• The Air Bag Warning Light does not come on during
the four to eight seconds when the ignition switch is
first turned to the ON/RUN position.
• The Air Bag Warning Light remains on after the four to
eight-second interval.
• The Air Bag Warning Light comes on intermittently or
remains on while driving.
NOTE: If the speedometer, tachometer, or any engine
related gauges are not working, the Occupant Restraint
Controller (ORC) may also be disabled. The air bags may
not be ready to inflate for your protection. Promptly
check the fuse block for blown fuses. Refer to the label
located on the inside of the fuse block cover for the
proper air bag fuses. See your authorized dealer if the
fuse is good.
Event Data Recorder (EDR)
This vehicle is equipped with an event data recorder
(EDR). The main purpose of an EDR is to record, in
certain crash or near crash-like situations, such as an air
bag deployment or hitting a road obstacle, data that will
assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to
vehicle dynamics and safety systems for a short period of
time, typically 30 seconds or less. The EDR in this vehicle
is designed to record such data as:
• How various systems in your vehicle were operating;
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81
• Whether or not the driver and passenger safety belts In addition to the vehicle manufacturer, other parties,
such as law enforcement, that have the special equipwere buckled/fastened;
ment, can read the information if they have access to the
• How far (if at all) the driver was depressing the
vehicle or the EDR.
accelerator and/or brake pedal; and,
Child Restraints
• How fast the vehicle was traveling.
Everyone in your vehicle needs to be buckled up all the
These data can help provide a better understanding of time, including babies and children. Every state in the
the circumstances in which crashes and injuries occur.
United States, and all Canadian provinces, require that
small children ride in proper restraint systems. This is the
NOTE: EDR data are recorded by your vehicle only if a
law, and you can be prosecuted for ignoring it.
non-trivial crash situation occurs; no data are recorded by
the EDR under normal driving conditions and no per- Children 12 years or under should ride properly buckled
sonal data (e.g., name, gender, age, and crash location) up in a rear seat, if available. According to crash statistics,
are recorded. However, other parties, such as law en- children are safer when properly restrained in the rear
forcement, could combine the EDR data with the type of seats rather than in the front.
personally identifying data routinely acquired during a
There are different sizes and types of restraints for
crash investigation.
children from newborn size to the child almost large
To read data recorded by an EDR, special equipment is enough for an adult safety belt. Always check the child
required, and access to the vehicle or the EDR is needed.
2
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
seat Owner’s Manual to ensure you have the right seat facing child safety seat. Two types of child restraints can
for your child. Use the restraint that is correct for your be used rearward-facing: infant carriers and convertible
child.
child seats.
The infant carrier is only used rearward-facing in the
vehicle. It is recommended for children from birth until
In a collision, an unrestrained child, even a tiny baby, they reach the weight or height limit of the infant carrier.
Convertible child seats can be used either rearwardcan become a projectile inside the vehicle. The force
facing or forward-facing in the vehicle. Convertible child
required to hold even an infant on your lap can
become so great that you could not hold the child, no seats often have a higher weight limit in the rearwardmatter how strong you are. The child and others facing direction than infant carriers do, so they can be
could be badly injured. Any child riding in your used rearward-facing by children who have outgrown
vehicle should be in a proper restraint for the child’s their infant carrier but are still less than at least two years
old. Children should remain rearward-facing until they
size.
reach the highest weight or height allowed by their
convertible child seat. Both types of child restraints are
Infants And Child Restraints
Safety experts recommend that children ride rearward- held in the vehicle by the lap/shoulder belt or the
facing in the vehicle until they are two years old or until LATCH child restraint anchor system. Refer to “Lower
they reach either the height or weight limit of their rear Anchors and Tether for CHildren (LATCH)”.
WARNING!
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83
WARNING!
• Rearward-facing child seats must never be used in
the front seat of a vehicle with the front passenger
air bag. An air bag deployment could cause severe
injury or death to infants in this position.
• Improper installation can lead to failure of an
infant or child restraint. It could come loose in a
collision. The child could be badly injured or
killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
• A rearward-facing infant restraint should only be
used in a rear seat. A rearward-facing infant restraint in the front seat may be struck by a deploying passenger air bag which may cause severe or
fatal injury to the infant.
Here are some tips for getting the most out of your child
restraint:
• Before buying any restraint system, make sure that it
has a label certifying that it meets all applicable Safety
Standards. Chrysler Group LLC also recommends that
you try a child restraint in the vehicle seats where you
will use it before you buy it.
• The restraint must be appropriate for your child’s
weight and height. Check the label on the restraint for
weight and height limits.
• Carefully follow the instructions that come with the
restraint. If you install the restraint improperly, it may
not work when you need it.
• The second row seating positions are equipped with
automatic locking retractors (ALR). To install child
restraint seats pull the belt from the retractor until
there is enough allowance to pass it through the child
2
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
restraint and slide the latch plate into the buckle. Then,
pull the shoulder belt until it is fully extended from the
retractor. Allow the belt to return into the retractor,
pulling on the excess webbing to tighten the lap
portion around the child restraint. For additional
information, refer to ⬙Automatic Locking Retractors
Mode⬙ earlier in the Occupant Restraints Section of the
owners’ manual.
NOTE: For additional information, refer to
www.seatcheck.org or call 1–866–SEATCHECK.
Canadian residents should refer to Transport Canada’s
website for additional information: http://www.tc.gc.ca/
roadsafety/safedrivers/childsafety/index.htm
Older Children And Child Restraints
Children who are two years old or who have outgrown
their rear-facing convertible child seat can ride forward• Buckle the child into the restraint exactly as the facing in the vehicle. Forward-facing child seats and
manufacturer’s instructions tell you.
convertible child seats used in the forward-facing direction are for children who are over two years old or who
WARNING!
have outgrown the rear-facing weight or height limit of
their rear-facing convertible child seat. Children should
When your child restraint is not in use, secure it in
remain in a forward-facing child seat with a harness for
the vehicle with the seat belt or remove it from the
as long as possible, up to the highest weight or height
vehicle. Do not leave it loose in the vehicle. In a
allowed by the child seat. These child seats are also held
sudden stop or accident, it could strike the occupants
in the vehicle by the lap/shoulder belt or the LATCH
or seatbacks and cause serious personal injury.
child restraint anchorage system. Refer to “Lower Anchors and Tether for CHildren (LATCH)”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85
All children whose weight or height is above the
forward-facing limit for the child seat should use a
belt-positioning booster seat until the vehicle’s seat belts
fit properly. If the child cannot sit with knees bent over
the vehicle’s seat cushion while the child’s back is against
the seatback, they should use a belt-positioning booster
seat. The child and belt-positioning booster seat are held
in the vehicle by the lap/shoulder belt.
• If the shoulder belt contacts the face or neck, move the
child closer to the center of the vehicle. Never allow a
child to put the shoulder belt under an arm or behind
the back.
Lower Anchors and Tether for CHildren (LATCH)
Your vehicle’s rear seat is equipped with the child
restraint anchorage system called LATCH. The LATCH
system provides for the installation of the child restraint
Children Too Large For Booster Seats
without using the vehicle’s seat belts, instead securing
Children who are large enough to wear the shoulder belt the child restraint using lower anchorages and upper
comfortably, and whose legs are long enough to bend tether straps from the child restraint to the vehicle
over the front of the seat when their back is against the structure.
seatback, should use the lap/shoulder belt in a rear seat.
LATCH-compatible child restraint systems are now avail• Make sure that the child is upright in the seat.
able. However, because the lower anchorages are to be
• The lap portion should be low on the hips and as snug introduced over a period of years, child restraint systems
having attachments for those anchorages will continue to
as possible.
also have features for installation using the vehicle’s seat
• Check belt fit periodically. A child’s squirming or
belts. Child restraints having tether straps and hooks for
slouching can move the belt out of position.
2
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
lower anchors can be are just visible when you lean into
the rear seat to install the child restraint. You will easily
feel them if you run your finger along the intersection of
the seatback and seat cushion surfaces. The vehicle’s seat
belt must be used for the center position. Regardless of
the specific type of lower attachment, never install
LATCH-compatible child seats such that two seats share
NOTE: When using the LATCH attaching system to
a common lower anchorage.
install a child restraint, please ensure that all seat belts
not being used for occupant restraints are stowed and out If you are installing LATCH-compatible child restraints
of reach of children. Remind all children in the vehicle in adjacent rear seating positions, you can use the
that the seat belts are not toys and should not be played LATCH anchors or the vehicle’s seat belt for the outboard
with, and never leave your child unattended in the position, but you must use the vehicle’s seat belt at the
center position. If your child restraints are not LATCHvehicle.
compatible, you can only install the child restraints using
The rear outboard seating positions have
the vehicle’s seat belts. For typical installation instruclower anchorages capable of accommodating
tions, refer to “Installing The LATCH-Compatible Child
LATCH-compatible child seats having flexible,
Restraint System”.
webbing-mounted lower attachments and
child seats with fixed lower attachments. The rear seat
connection to the top tether anchorages have been available for some time. For some older child restraints, many
child restraint manufacturers offer add-on tether strap
kits or retro-fit kits. You are urged to take advantage of all
the available attachments provided with your child restraint in any vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87
Installing The LATCH-Compatible Child Restraint
System
We urge you to carefully follow the directions of the
manufacturer when installing your child restraint. Not all
child restraint systems will be installed as described here.
Again, carefully follow the installation instructions that
were provided with the child restraint system.
The rear seat lower anchorages are round bars, located at
the rear of the seat cushion where it meets the seatback,
and are just visible when you lean into the rear seat to
install the child restraint. You will easily feel them if you
run your finger along the intersection of the seatback and
seat cushion surfaces.
2
Latch Anchorages (60/40 Seat)
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Latch Anchorages (Captain’s Chair)
In addition, there are top tether strap anchorages behind
each rear seating position located on the back of the seat.
To access the top tether strap anchorages behind the rear
seat, pull the carpeted floor panel away from the seat
back, this will expose the top tether strap anchorages.
Pulling Down The Carpet Floor Panel
To Access Top Tether Strap
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89
2
Top Tether Strap Anchorage (Located on Seatback)
Top Tether Strap Mounting (60/40 Seat)
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Many, but not all, restraint systems will be equipped with
separate straps on each side, with each having a hook or
connector for attachment to the lower anchorage and a
means of adjusting the tension in the strap. Forwardfacing toddler restraints and some rear-facing infant
restraints will also be equipped with a tether strap, a
hook for attachment to the tether strap anchorage and a
means of adjusting the tension of the strap.
Top Tether Strap Mounting (Captain’s Chair)
WARNING!
Do not use the cargo tie downs located on the load
floor. Improper usage of the tether can lead to a
failure of an infant or child restraint. The child could
be badly injured or killed.
First, loosen the child seat adjusters on the lower straps
and on the tether strap so that you can more easily attach
the hooks or connectors to the vehicle anchorages. Next,
attach the lower hooks or connectors over the top of the
anchorage bars, pushing aside the seat cover material.
Then, locate the tether anchorage directly behind the seat
where you are placing the child restraint and attach the
tether strap to the anchorage, being careful to route the
tether strap to provide the most direct path between the
anchor and the child restraint. There are three top tether
anchorages located on the back of the seat, behind the
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91
gap panel. They are not visible until you fold the gap
panel down. Do not use the cargo tie down hooks
located on the floor behind the seat. Finally, tighten all
three straps as you push the child restraint rearward and
downward into the seat, removing slack in the straps
according to the child restraint manufacturer’s instructions.
WARNING!
Improper installation of a child restraint to the
LATCH anchorages can lead to failure of an infant or
child restraint. The child could be badly injured or
killed. Follow the manufacturer’s directions exactly
when installing an infant or child restraint.
Installing Child Restraints Using The Vehicle Seat
Belts
The seat belts in the passenger seating positions are
equipped with an Automatic Locking Retractor to secure
a Child Restraint System (CRS). These types of seat belts
are designed to keep the lap portion of the seat belt tight
around the child restraint so that it is not necessary to use
a locking clip. The ALR will make a ratcheting noise if
you extract the entire belt from the retractor and then
allow the belt to retract into the retractor. For additional
information on ALR, refer to “Automatic Locking Mode”
description under “Seat Belts In Passenger Seating Positions” section. The chart below defines the seating positions with an Automatic Locking Retractor (ALR) or a
cinching latch plate.
2
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
First Row
Second Row
— Captains
Chair
Second Row
— Bench
Second Row
Third Row
Driver
CRS Lock
N/A
ALR
Center
CRS Lock
N/A
N/A
Passenger
CRS Lock
ALR
ALR
ALR
ALR
ALR
ALR
ALR
ALR
N/A
ALR
ALR
extract all the seat belt webbing out of the retractor and
then allow the belt to retract into the retractor. As the belt
retracts, you will hear a ratcheting sound. This indicates
the safety belt is now in the Automatic Locking mode.
2. Finally, pull on any excess webbing to tighten the lap
portion around the child restraint. Any seat belt system
will loosen with time, so check the belt occasionally, and
pull it tight if necessary.
In the rear center seat, you may have trouble tightening
the lap/shoulder belt on the child restraint because the
buckle or latch plate is too close to the belt path opening
• N/A — Not Applicable
on the restraint. Disconnect the latch plate from the
• ALR — Automatic Locking Retractor
buckle and twist the short buckle-end belt several times
to shorten it. Insert the latch plate into the buckle with the
Installing a Child Restraint with an ALR:
release button facing out. If the belt still can’t be tight1. To install a child restraint with ALR, first, pull enough ened, or if pulling and pushing on the restraint loosens
of the seat belt webbing from the retractor to route it the belt, disconnect the latch plate from the buckle, turn
through the belt path of the child restraint. Slide the latch
plate into the buckle until you hear a “click.” Next,
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93
the buckle around, and insert the latch plate into the
buckle again. If you still can’t make the child restraint
secure, try a different seating position.
2
To attach a child restraint tether strap:
For rearward facing infant seats secured in the center seat
position with the vehicle seat belts, the rear center seat
position has an armrest tether that secures the arm rest in
the upward position. To access the center seat arm rest
tether first lower the arm rest. The tether is located
behind the armrest and hooked onto the plastic seat
backing.
Center Seat Position Arm Rest Tether
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Pull down on the tether to unhook it from the plastic seat and attach the hook to the top tether anchor located on the
backing, then raise the armrest and attach the tether hook back of the seat. To access the top tether strap anchorages
behind the rear seat, pull the carpeted floor panel away
to the strap located on the front of the arm rest.
from the seat back, this will expose the top tether strap
anchorages.
Center Seat Position Arm Rest Tether Attached
For center seating position route the tether strap over the
seatback and headrest then attach the hook to the tether
anchor located on the back of the seat. For the outboard
seating positions, route the tether under the head restraints,
Pulling Down The Carpet Floor Panel
To Access Top Tether Strap
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95
2
Top Tether Strap Anchorage (Located on Seatback)
Top Tether Strap Mounting (60/40 Seat)
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
• An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchor positions directly behind the child seat to secure a child restraint top
tether strap.
• Do not use the cargo tie downs located on the load
floor. Improper usage of the tether can lead to a
failure of an infant or child restraint. The child
could be badly injured or killed.
Top Tether Strap Mounting (Captain’s Chair)
Top Tether Strap Attachment
For the center seating position route the tether strap over
the seatback and headrest then attach the hook to the top
tether anchorage located on the back of the seat behind
the gap panel. For the outboard seating positions, route
the tether strap under the headrests and attach the hook
to the top tether anchorage located on the back of the seat
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97
behind the gap panel. Please note the top tether anchorages are not visible until you fold the gap panel down.
Do not use the cargo tie down hooks located on the
floor behind the seats.
While cruising, brief full-throttle acceleration within the
limits of local traffic laws contributes to a good break-in.
Wide-open throttle acceleration in low gear can be detrimental and should be avoided.
Transporting Pets
Air Bags deploying in the front seat could harm your pet.
An unrestrained pet will be thrown about and possibly
injured, or injure a passenger during panic braking or in
a collision. Pets should be restrained in the rear seat in
pet harnesses or pet carriers that are secured by seat belts.
The engine oil installed in the engine at the factory is a
high-quality energy conserving type lubricant. Oil
changes should be consistent with anticipated climate
conditions under which vehicle operations will occur. For
the recommended viscosity and quality grades, refer to
“Maintenance Procedures” in “Maintaining Your Vehicle”.
ENGINE BREAK-IN RECOMMENDATIONS
A long break-in period is not required for the engine and
drivetrain (transmission and axle) in your vehicle.
Never use Non-Detergent Oil or Straight Mineral Oil
in the engine or damage may result.
CAUTION!
Drive moderately during the first 300 miles (500 km).
After the initial 60 miles (100 km), speeds up to 50 or NOTE: A new engine may consume some oil during its
first few thousand miles (kilometers) of operation. This
55 mph (80 or 90 km/h) are desirable.
should be considered a normal part of the break-in and
not interpreted as an indication of difficulty.
2
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
SAFETY TIPS
Exhaust Gas
Transporting Passengers
NEVER TRANSPORT PASSENGERS IN THE CARGO
AREA.
WARNING!
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
• It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seriously injured or killed.
• Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat
belts.
• Be sure everyone in your vehicle is in a seat and
using a seat belt properly.
WARNING!
Exhaust gases can injure or kill. They contain carbon
monoxide (CO), which is colorless and odorless.
Breathing it can make you unconscious and can
eventually poison you. To avoid breathing (CO),
follow these safety tips:
• Do not run the engine in a closed garage or in
confined areas any longer than needed to move
your vehicle in or out of the area.
• If you are required to drive with the trunk/liftgate
open, make sure that all windows are closed and
the climate control BLOWER switch is set at high
speed. DO NOT use the recirculation mode.
(Continued)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99
WARNING! (Continued)
• If it is necessary to sit in a parked vehicle with the
engine running, adjust your heating or cooling
controls to force outside air into the vehicle. Set
the blower at high speed.
Safety Checks You Should Make Inside The
Vehicle
Seat Belts
Inspect the belt system periodically, checking for cuts,
frays, and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system.
The best protection against carbon monoxide entry into
Front seat belt assemblies must be replaced after a
the vehicle body is a properly maintained engine exhaust
collision. Rear seat belt assemblies must be replaced after
system.
a collision if they have been damaged (i.e., bent retractor,
Whenever a change is noticed in the sound of the exhaust torn webbing, etc.). If there is any question regarding belt
system, when exhaust fumes can be detected inside the or retractor condition, replace the belt.
vehicle, or when the underside or rear of the vehicle is
damaged, have a competent mechanic inspect the com- Air Bag Warning Light
plete exhaust system and adjacent body areas for broken, The light should come on and remain on for four to eight
damaged, deteriorated, or mispositioned parts. Open seconds as a bulb check when the ignition switch is first
seams or loose connections could permit exhaust fumes turned ON. If the light is not lit during starting, see your
to seep into the passenger compartment. In addition, authorized dealer. If the light stays on, flickers, or comes
inspect the exhaust system each time the vehicle is raised on while driving, have the system checked by an authorized dealer.
for lubrication or oil change. Replace as required.
2
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Defroster
Check operation by selecting the defrost mode and place
the blower control on high speed. You should be able to
feel the air directed against the windshield. See your
authorized dealer for service if your defroster is
inoperable.
Floor Mat Safety Information
Always use floor mats designed to fit the footwell of your
vehicle. Use only floor mats that leave the pedal area
unobstructed and that are firmly secured so that they
cannot slip out of position and interfere with the pedals
or impair safe operation of your vehicle in other ways.
WARNING!
Pedals that cannot move freely can cause loss of
vehicle control and increase the risk of serious personal injury.
(Continued)
WARNING! (Continued)
• Always make sure that floor mats are properly
attached to the floor mat fasteners.
• Never place or install floor mats or other floor
coverings in the vehicle that cannot be properly
secured to prevent them from moving and interfering with the pedals or the ability to control the
vehicle.
• Never put floor mats or other floor coverings on
top of already installed floor mats. Additional
floor mats and other coverings will reduce the size
of the pedal area and interfere with the pedals.
• Check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that
have been removed for cleaning.
(Continued)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101
WARNING! (Continued)
• Always make sure that objects cannot fall into the
driver footwell while the vehicle is moving. Objects
can become trapped under the brake pedal and
accelerator pedal causing a loss of vehicle control.
• If required, mounting posts must be properly
installed, if not equipped from the factory.
Failure to properly follow floor mat installation or
mounting can cause interference with the brake
pedal and accelerator pedal operation causing loss
of control of the vehicle.
Periodic Safety Checks You Should Make Outside
The Vehicle
Tires
Examine tires for excessive tread wear and uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread or sidewall. Inspect the tread for cuts
and cracks. Inspect sidewalls for cuts, cracks and bulges.
Check the wheel nuts for tightness. Check the tires
(including spare) for proper cold inflation pressure.
Lights
Have someone observe the operation of exterior lights
while you work the controls. Check turn signal and high
beam indicator lights on the instrument panel.
Door Latches
Check for positive closing, latching, and locking.
Fluid Leaks
Check area under vehicle after overnight parking for fuel,
engine coolant, oil, or other fluid leaks. Also, if gasoline
fumes are detected or if fuel, power steering fluid, or
brake fluid leaks are suspected, the cause should be
located and corrected immediately.
2
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . 110
▫ Automatic Dimming Mirror — If Equipped . . 110
▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 111
▫ Outside Mirrors Folding Feature . . . . . . . . . 112
▫ Outside Automatic Dimming Mirrors —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 112
▫ Tilt Mirrors In Reverse (Available With
Memory Seat Only) — If Equipped . . . . . . . . 113
▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . 114
▫ Sun Visor Extension — If Equipped . . . . . . . 114
䡵 Blind Spot Monitoring — If Equipped . . . . . . . 115
▫ Rear Cross Path . . . . . . . . . . . . . . . . . . . . . 120
▫ Modes Of Operation . . . . . . . . . . . . . . . . . . 122
▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . 112 䡵 Uconnect™ Phone — If Equipped . . . . . . . . . . 123
▫ Heated Mirrors — If Equipped . . . . . . . . . . . 113
▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . 125
3
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
▫ Phone Call Features . . . . . . . . . . . . . . . . . . 132
▫ Power Lumbar — If Equipped . . . . . . . . . . . 162
▫ Uconnect™ Phone Features . . . . . . . . . . . . . 135
▫ Manual Front Passenger Seat Forward/
Rearward Adjustment . . . . . . . . . . . . . . . . . 163
▫ Advanced Phone Connectivity . . . . . . . . . . . 140
▫ Things You Should Know About Your
Uconnect™ Phone . . . . . . . . . . . . . . . . . . . . 142
▫ General Information . . . . . . . . . . . . . . . . . . 153
䡵 Voice Command — If Equipped . . . . . . . . . . . 153
▫ Voice Command System Operation . . . . . . . . 153
▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 154
▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . 158
䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
▫ Power Seats — If Equipped . . . . . . . . . . . . . 158
▫ Passenger’s Power Seat — If Equipped . . . . . 160
▫ Manual Front Passenger Seatback
Adjustment — Recline . . . . . . . . . . . . . . . . . 164
▫ Front Passenger Seat Fold-Flat Feature —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 164
▫ Heated Seats — If Equipped . . . . . . . . . . . . 165
▫ Ventilated Seats — If Equipped . . . . . . . . . . 168
▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . 168
▫ 60/40 Split Rear Seat — If Equipped . . . . . . 174
▫ Rear Captain Chairs — If Equipped . . . . . . . 177
▫ Folding Third Row . . . . . . . . . . . . . . . . . . . 180
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105
䡵 Driver Memory Seat — If Equipped . . . . . . . . 182
▫ Daytime Running Lights — If Equipped . . . . 191
▫ Setting Memory Positions And Linking
Remote Keyless Entry Transmitter To
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . 191
▫ Memory Position Recall . . . . . . . . . . . . . . . . 184
▫ Parking Lights And Panel Lights . . . . . . . . . 191
▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 192
▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 192
▫ To Disable A RKE Transmitter Linked To
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 194
▫ Easy Entry/Exit Seat . . . . . . . . . . . . . . . . . . 185
▫ Battery Saver . . . . . . . . . . . . . . . . . . . . . . . 194
䡵 To Open And Close The Hood . . . . . . . . . . . . 186
▫ Front Map/Reading Lights . . . . . . . . . . . . . 194
䡵 Lights
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
▫ Courtesy Lights . . . . . . . . . . . . . . . . . . . . . 195
▫ Headlight Switch . . . . . . . . . . . . . . . . . . . . 188
▫ Ambient Light . . . . . . . . . . . . . . . . . . . . . . 196
▫ Automatic Headlights — If Equipped . . . . . . 189
▫ Multifunction Lever . . . . . . . . . . . . . . . . . . 196
▫ Headlights On Automatically With Wipers . . 189
▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . 197
▫ Smartbeam™ — If Equipped . . . . . . . . . . . . 190
▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . 197
3
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . 197
䡵 Electronic Speed Control . . . . . . . . . . . . . . . . 205
▫ High/Low Beam Switch . . . . . . . . . . . . . . . 197
▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 206
䡵 Windshield Wipers And Washers . . . . . . . . . . 198
▫ To Set A Desired Speed . . . . . . . . . . . . . . . . 207
▫ Windshield Wiper Operation . . . . . . . . . . . . 198
▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . 207
▫ Intermittent Wiper System . . . . . . . . . . . . . . 199
▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 207
▫ Windshield Washer Operation . . . . . . . . . . . 200
▫ To Vary The Speed Setting . . . . . . . . . . . . . . 207
▫ Mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
▫ To Accelerate For Passing . . . . . . . . . . . . . . 208
▫ Rain Sensing Wipers — If Equipped . . . . . . . 201
䡵 Adaptive Cruise Control (ACC) —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 208
䡵 Tilt/Telescoping Steering Column . . . . . . . . . . 202
䡵 Power Tilt/Telescoping Steering Column —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 203
䡵 Heated Steering Wheel — If Equipped
. . . . . . 204
▫ Adaptive Cruise Control (ACC) Operation . . 211
▫ Activating Adaptive Cruise Control (ACC) . . 212
▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 212
▫ To Set A Desired ACC Speed . . . . . . . . . . . . 214
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107
▫ To Cancel . . . . . . . . . . . . . . . . . . . . . . . . . . 215
䡵 Parksense威 Rear Park Assist — If Equipped . . . 237
▫ To Turn Off . . . . . . . . . . . . . . . . . . . . . . . . 216
▫ Parksense威 Sensors . . . . . . . . . . . . . . . . . . . 237
▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 216
▫ Parksense威 Warning Display . . . . . . . . . . . . 237
▫ To Vary The Speed Setting . . . . . . . . . . . . . . 217
▫ Parksense威 Display . . . . . . . . . . . . . . . . . . . 238
▫ Setting The Following Distance In ACC . . . . 218
▫ Enabling And Disabling Parksense威 . . . . . . . 241
▫ Adaptive Cruise Control (ACC) Menu . . . . . 221
▫ Service The Parksense威 Rear Park Assist
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
▫ Display Warnings And Maintenance . . . . . . . 222
▫ Precautions While Driving With ACC . . . . . . 225
▫ General Information . . . . . . . . . . . . . . . . . . 229
▫ Normal (Fixed Speed) Cruise
Control Mode . . . . . . . . . . . . . . . . . . . . . . . 230
▫ Forward Collision Warning — If Equipped . . 232
▫ Cleaning The Parksense威 System . . . . . . . . . 242
▫ Parksense威 System Usage Precautions . . . . . . 243
䡵 Parkview威 Rear Back Up Camera — If
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
▫ Turning Parkview威 On Or Off — With
Navigation/Multimedia Radio . . . . . . . . . . . 247
3
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
▫ Turning Parkview威 On Or Off — Without
Navigation/Multimedia Radio . . . . . . . . . . . 248
䡵 Overhead Console . . . . . . . . . . . . . . . . . . . . . 248
▫ Front Map/Reading Lights . . . . . . . . . . . . . 248
▫ Courtesy Lights . . . . . . . . . . . . . . . . . . . . . 249
▫ Sunglass Bin Door . . . . . . . . . . . . . . . . . . . 250
䡵 Garage Door Opener — If Equipped . . . . . . . . 250
▫ Before You Begin Programming
HomeLink威 . . . . . . . . . . . . . . . . . . . . . . . . 252
▫ Programming A Rolling Code . . . . . . . . . . . 252
▫ Programming A Non-Rolling Code . . . . . . . . 254
▫ Canadian/Gate Operator Programming . . . . 255
▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 257
▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 258
▫ General Information . . . . . . . . . . . . . . . . . . 259
䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 259
▫ Opening Sunroof — Express . . . . . . . . . . . . 260
▫ Opening Sunroof — Manual Mode . . . . . . . . 260
▫ Closing Sunroof — Express . . . . . . . . . . . . . 260
▫ Closing Sunroof — Manual Mode . . . . . . . . 261
▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 261
▫ Venting Sunroof — Express . . . . . . . . . . . . . 261
▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 261
▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 262
▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 262
▫ Ignition Off Operation . . . . . . . . . . . . . . . . . 262
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 262 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . 279
䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 263
▫ Rechargeable Flashlight . . . . . . . . . . . . . . . . 279
䡵 Power Inverter — If Equipped . . . . . . . . . . . . 268
▫ Cargo Storage . . . . . . . . . . . . . . . . . . . . . . . 280
䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 270
▫ Retractable Cargo Area Cover —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 280
▫ Front Seat Cupholders . . . . . . . . . . . . . . . . . 270
▫ Rear Cupholders . . . . . . . . . . . . . . . . . . . . . 270
䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
▫ Glove Compartment . . . . . . . . . . . . . . . . . . 272
▫ Door Storage . . . . . . . . . . . . . . . . . . . . . . . 273
▫ Front Center Console . . . . . . . . . . . . . . . . . 273
▫ Rear Full Center Console (If Equipped) . . . . . 275
▫ Rear Mini Center Console (If Equipped) . . . . 278
▫ Cargo Tie-Down Hooks . . . . . . . . . . . . . . . . 281
䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 282
▫ Rear Window Wiper/Washer . . . . . . . . . . . . 282
▫ Rear Window Defroster . . . . . . . . . . . . . . . . 283
䡵 Roof Luggage Rack — If Equipped . . . . . . . . . 284
▫ Deploying The Crossbars . . . . . . . . . . . . . . . 285
▫ Stowing The Crossbars . . . . . . . . . . . . . . . . 288
3
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
MIRRORS
Inside Day/Night Mirror
A two-point pivot system allows for horizontal and
vertical adjustment of the mirror. Adjust the mirror to
center on the view through the rear window. The mirror
should be adjusted while set in the day position (toward
the windshield).
Headlight glare can be reduced by moving the small
control lever under the mirror to the night position (lever
flipped toward the rear of vehicle).
Adjusting Rearview Mirror
Automatic Dimming Mirror — If Equipped
This mirror automatically adjusts for headlight glare
from vehicles behind you. You can turn the feature on or
off by pressing the button at the base of the mirror. A light
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
in the button will illuminate to indicate when the dimming feature is activated. The mirror is twisted on the
windshield button counterclockwise and requires no
tools for mounting.
NOTE: This feature is disabled when the vehicle is
moving in reverse.
CAUTION!
To avoid damage to the mirror during cleaning, never
spray any cleaning solution directly onto the mirror.
Apply the solution onto a clean cloth and wipe the
mirror clean.
Outside Mirrors
To receive maximum benefit, adjust the outside mirrors
to center on the adjacent lane of traffic with a slight
overlap of the view obtained on the inside mirror.
Automatic Dimming Mirror
3
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
Vehicles and other objects seen in the passenger side
convex mirror will look smaller and farther away
than they really are. Relying too much on your
passenger side convex mirror could cause you to
collide with another vehicle or other object. Use your
inside mirror when judging the size or distance of a
vehicle seen in the passenger side convex mirror.
Some vehicles will not have a convex passenger side
mirror.
Outside Mirrors Folding Feature
All outside mirrors are hinged and may be moved either
forward or rearward to resist damage. The hinges have
three detent positions: full forward, full rearward and
normal.
Outside Automatic Dimming Mirrors — If
Equipped
The drivers outside mirror will automatically adjust for
glare from vehicles behind you. This feature is controlled
by the inside automatic dimming mirror and can be
turned on or off by pressing the button at the base of the
inside mirror. The mirrors will automatically adjust for
headlight glare when the inside mirror adjusts.
Power Mirrors
The power mirror switch is located on the driver’s side
door trim panel.
The power mirror controls consist of mirror select buttons and a four-way mirror control switch. To adjust a
mirror, press the mirror select button for the mirror that
you want to adjust. Using the mirror control switch, press
on any of the four arrows for the direction that you want
the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113
Heated Mirrors — If Equipped
These mirrors are heated to melt frost or ice. This
feature is activated whenever you turn on the rear
window defroster. Refer to “Rear Window Features” in
“Understanding The Features Of Your Vehicle” for further information.
Tilt Mirrors In Reverse (Available With Memory
Seat Only) — If Equipped
Tilt Mirrors in Reverse provides automatic outside mirror
positioning which will aid the drivers view of the ground
rearward of the front doors. Outside mirrors will move
slightly downward from the present position when the
Power Mirror Switch
vehicle is shifted into REVERSE. Outside mirrors will
1 — Mirror Direction Control
then return to the original position when the vehicle is
2 — Mirror Selection
shifted out of REVERSE position. Each stored memory
Power mirror preselected positions can be controlled by setting will have an associated Tilt Mirrors in Reverse
the optional Memory Seat Feature. Refer to “Driver position.
Memory Seat” in “Understanding The Features Of Your
Vehicle” for further information.
3
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: The Tilt Mirrors in Reverse feature is not enabled when delivered from the factory. The Tilt Mirrors
in Reverse feature can be enabled or disabled in the
Electronic Vehicle Information Center (EVIC). Refer to
“Electronic Vehicle Information Center (EVIC)/
Customer- Programmable Features” in “Understanding
Your Instrument Panel” for further information.
Illuminated Vanity Mirrors
To access an illuminated vanity mirror, flip down one of
the visors.
Lift the cover to reveal the mirror. The light will turn on
automatically.
Illuminated Vanity Mirror
Sun Visor Extension — If Equipped
This feature has a pull out extension on the sun visor for
increased coverage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
BLIND SPOT MONITORING — IF EQUIPPED
The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to
detect highway licensable vehicles (automobiles, trucks,
motorcycles, etc.) that enter the blind spot zones from the
rear/front/side of the vehicle.
When the vehicle is started, the BSM warning light will
be momentarily illuminated in both outside rear view
mirrors to let the driver know that the system is operational. The BSM system sensors operate when the vehicle
is in any forward gear or REVERSE and enters stand by
mode when the vehicle is in PARK.
The BSM detection zone covers approximately one lane
on both sides of the vehicle (11 ft or 3.35 m). The zone
starts at the outside rear view mirror and extends approximately 20 ft (6 m) to the rear of the vehicle. The BSM
system monitors the detection zones on both sides of the
vehicle when the vehicle speed has reached approximately 6 mph (10 km/h) or higher and will alert the
driver of vehicles in these areas.
Rear Detection Zones
NOTE:
• The BSM system does NOT alert the driver about
rapidly approaching vehicles that are outside the
detection zones.
3
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• The BSM system detection zone DOES NOT change if
your vehicle is towing a trailer. Therefore, visually
verify the adjacent lane is clear for both your vehicle
and trailer before making a lane change. If the trailer
or other object (i.e., bicycle, sports equipment) extends
beyond the side of your vehicle, this may result in the
BSM warning light remaining illuminated the entire
time the vehicle is in a forward gear.
The area on the rear fascia where the radar sensors are
located must remain free of snow, ice, and dirt/road
contamination so that the BSM system can function
properly. Do not block the area of the rear fascia where
Sensor Location (Driver Side Shown)
the radar sensors are located with foreign objects (bumThe BSM system notifies the driver of objects in the
per stickers, bicycle racks, etc.).
detection zones by illuminating the BSM warning light
located in the outside mirrors in addition to sounding an
audible (chime) alert and reducing the radio volume.
Refer to “Modes Of Operation” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
Entering From The Side
Vehicles that move into your adjacent lanes from either
side of the vehicle.
3
BSM Warning Light
The BSM system monitors the detection zone from three
different entry points (Side, Rear, Front) while driving to
see if an alert is necessary. The BSM system will issue an
alert during these types of zone entries.
Side Monitoring
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Entering From The Rear
Vehicles that come up from behind your vehicle on either
side and enter the rear detection zone with a relative
speed of less than 30 mph (48 km/h).
Overtaking Traffic
If you pass another vehicle slowly (with a relative speed
of less than 10 mph (16 km/h) and the vehicle remains in
the blind spot for approximately 1.5 seconds, the warning
light will be illuminated. If the difference in speed
between the two vehicles is greater than 10 mph
(16 km/h), the warning light will not illuminate.
Rear Monitoring
Overtaking/Approaching
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119
The BSM system is designed not to issue an alert on
stationary objects such as guardrails, posts, walls, foliage,
berms, etc. However, occasionally the system may alert
on such objects. This is normal operation and your
vehicle does not require service.
3
Overtaking/Passing
Stationary Objects
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The BSM system will not alert you of objects that are
traveling in the opposite direction of the vehicle in
adjacent lanes.
Opposing Traffic
WARNING!
The Blind Spot Monitoring system is only an aid to
help detect objects in the blind spot zones. The BSM
system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped
with the BSM system, always check your vehicles
mirrors, glance over your shoulder, and use your turn
signal before changing lanes. Failure to do so can
result in serious injury or death.
Rear Cross Path
The Rear Cross Path (RCP) feature is intended to aid the
driver when backing out of parking spaces where their
vision of oncoming vehicles may be blocked. Proceed
slowly and cautiously out of the parking space until the
rear end of the vehicle is exposed. The RCP system will
then have a clear view of the cross traffic and if an
oncoming vehicle is detected, alert the driver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121
NOTE: In a parking lot situation, oncoming vehicles can
be obscured by vehicles parked on either side. If the
sensors are blocked by other structures or vehicles, the
system will not be able to alert the driver.
When RCP is on and the vehicle is in REVERSE, the
driver is alerted using both the visual and audible
alarms, including radio muting.
WARNING!
RCP Detection Zones
RCP monitors the rear detection zones on both sides of
the vehicle, for objects that are moving toward the side of
the vehicle with a minimum speed of approximately 1 to
2 mph (1 km/h to 3 km/h), to objects moving a maximum of approximately 10 mph (16 km/h), such as in
parking lot situations.
RCP is not a Back Up Aid system. It is intended to be
used to help a driver detect an oncoming vehicle in a
parking lot situation. Drivers must be careful when
backing up, even when using RCP. Always check
carefully behind your vehicle, look behind you, and
be sure to check for pedestrians, animals, other
vehicles, obstructions, and blind spots before backing up. Failure to do so can result in serious injury or
death.
3
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Modes Of Operation
Three selectable modes of operation are available in the
Electronic Vehicle Information Center (EVIC). Refer to
“Electronic Vehicle Information Center (EVIC)/Personal
Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
turn signal is then activated, and it corresponds to an
alert present on that side of the vehicle, an audible chime
will also be sounded. Whenever a turn signal and detected object are present on the same side at the same
time, both the visual and audio alerts will be issued. In
addition to the audible alert the radio (if on) will also be
muted.
Blind Spot Alert
When operating in Blind Spot Alert mode, the BSM NOTE:
system will provide a visual alert in the appropriate side • Whenever an audible alert is requested by the BSM
system, the radio is also muted.
view mirror based on a detected object. However, when
the system is operating in RCP, the system will respond
• If the hazard flashers are on, the system will request
with both visual and audible alerts when a detected
the appropriate visual alert only.
object is present. Whenever an audible alert is requested,
When the system is in RCP, the system shall respond
the radio is muted.
with both visual and audible alerts when a detected
Blind Spot Alert Lights/Chime
object is present. Whenever an audible alert is reWhen operating in Blind Spot Alert Lights/Chime mode,
quested, the radio is also muted. Turn/hazard signal
the BSM system will provide a visual alert in the approstatus is ignored; the RCP state always requests the
priate side view mirror based on a detected object. If the
chime.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123
Blind Spot Alert Off
When the BSM system is turned off there will be no
visual or audible alerts from either the BSM or RCP
systems.
NOTE: The Uconnect™ Phone requires a mobile phone
equipped with the Bluetooth威 “Hands-Free Profile”, Version 0.96 or higher. See the Uconnect™ website for
supported phones.
NOTE: The BSM system will store the current operating For Uconnect™ customer support, visit the following
mode when the vehicle is shut off. Each time the vehicle websites:
is started the previously stored mode will be recalled and
• www.chrysler.com/uconnect
used.
• www.dodge.com/uconnect
Uconnect™ Phone — IF EQUIPPED
Uconnect™ Phone is a voice-activated, hands-free, in- • www.jeep.com/uconnect
vehicle communications system. Uconnect™ Phone al- • or call 1–877–855–8400
lows you to dial a phone number with your mobile
phone using simple voice commands (e.g., “Call” ѧ Uconnect™ Phone allows you to transfer calls between
“Mike” ѧ “Work” or “Dial” ѧ “248-555-1212”). Your the system and your mobile phone as you enter or exit
mobile phone’s audio is transmitted through your vehi- your vehicle and enables you to mute the system’s
cle’s audio system; the system will automatically mute microphone for private conversation.
your radio when using the Uconnect™ Phone.
The Uconnect™ Phone is driven through your Bluetooth威
“Hands-Free Profile” mobile phone. Uconnect™ features
3
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Bluetooth威 technology - the global standard that enables
different electronic devices to connect to each other without
wires or a docking station, so Uconnect™ Phone works no
matter where you stow your mobile phone (be it your
purse, pocket, or briefcase), as long as your phone is turned
on and has been paired to the vehicle’s Uconnect™ Phone.
The Uconnect™ Phone allows up to seven mobile phones
to be linked to the system. Only one linked (or paired)
mobile phone can be used with the system at a time.
The system is available in English, Spanish, or French
languages.
WARNING!
Any voice commanded system should be used only
in safe driving conditions following local laws and
phone use. All attention should be kept on the
roadway ahead. Failure to do so may result in a
collision causing serious injury or death.
Uconnect™ Phone Button
The radio or steering wheel controls (if
equipped) will contain the two control buttons
button and Voice Com(Uconnect™ Phone
button) that will enable you to
mand
access the system. When you press the button you will
hear the word Uconnect™ followed by a BEEP. The beep
is your signal to give a command.
Voice Command Button
Actual button location may vary with the radio. The individual buttons are described in the
“Operation” section.
The Uconnect™ Phone can be used with any Hands-Free
Profile certified Bluetooth威 mobile phone. See the
Uconnect™ website for supported phones. Refer to your
mobile service provider or the phone manufacturer for
details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125
The Uconnect™ Phone is fully integrated with the vehi- • For certain operations, compound commands can be
cle’s audio system. The volume of the Uconnect™ Phone
used. For example, instead of saying “Setup” and then
can be adjusted either from the radio volume control
“Pair a Device”, the following compound command
knob or from the steering wheel radio control (right
can be said: “Pair a Bluetooth威 Device”.
switch), if so equipped.
• For each feature explanation in this section, only the
compound form of the voice command is given. You
The radio display will be used for visual prompts from
can also break the commands into parts and say each
the Uconnect™ Phone such as “CELL” or caller ID on
part of the command when you are asked for it. For
certain radios.
example, you can use the compound form voice
Operation
command “Phonebook New Entry”, or you can break
Voice commands can be used to operate the Uconnect™
the compound form command into two voice comPhone and to navigate through the Uconnect™ Phone
mands: “Phonebook” and “New Entry”. Please remenu structure. Voice commands are required after most
member, the Uconnect™ Phone works best when you
Uconnect™ Phone prompts. You will be prompted for a
talk in a normal conversational tone, as if speaking to
specific command and then guided through the available
someone sitting a few feet/meters away from you.
options.
Voice Command Tree
• Prior to giving a voice command, one must wait for
Refer to “Voice Tree” in this section.
the beep, which follows the “Ready” prompt or another prompt.
3
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Help Command
If you need assistance at any prompt, or if you want to
know your options at any prompt, say “Help” following
the beep. The Uconnect™ Phone will play some of the
options at any prompt if you ask for help.
To complete the pairing process, you will need to reference your mobile phone Owner’s Manual. The
Uconnect™ website may also provide detailed instructions for pairing.
The following are general phone to Uconnect™ Phone
pairing instructions:
To activate the Uconnect™ Phone, simply press the
button and follow the audible prompts for directions.
• Press the
button to begin.
Uconnect™ Phone sessions begin with a press of the
button on the radio control head.
• After the “Ready” prompt and the following beep, say
“Device Pairing”.
Cancel Command
At any prompt, after the beep, you can say “Cancel” and • When prompted, after the beep, say “Pair a Device”
you will be returned to the main menu. However, in a
and follow the audible prompts.
few instances the system will take you back to the
• You will be asked to say a four-digit Personal Identiprevious menu.
fication Number (PIN), which you will later need to
Pair (Link) Uconnect™ Phone To A Mobile Phone
enter into your mobile phone. You can enter any
To begin using your Uconnect™ Phone, you must pair
four-digit PIN. You will not need to remember this PIN
your compatible Bluetooth威 enabled mobile phone.
after the initial pairing process.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127
• For identification purposes, you will be prompted to Dial By Saying A Number
give the Uconnect™ Phone a name for your mobile
button to begin.
• Press the
phone. Each mobile phone that is paired should be
• After the “Ready” prompt and the following beep, say
given a unique phone name.
“Dial”.
• You will then be asked to give your mobile phone a
priority level between one and seven, with one being • The system will prompt you to say the number you
want to call.
the highest priority. You can pair up to seven mobile
phones to your Uconnect™ Phone. However, at any
• For example, you can say “234-567-8901”.
given time, only one mobile phone can be in use,
connected to your Uconnect™ System. The priority • The Uconnect™ Phone will confirm the phone number
and then dial. The number will appear in the display
allows the Uconnect™ Phone to know which mobile
of certain radios.
phone to use if multiple mobile phones are in the
vehicle at the same time. For example, if priority three
Call By Saying A Name
and priority five phones are present in the vehicle, the
button to begin.
Uconnect™ Phone will use the priority three mobile • Press the
phone when you make a call. You can select to use a
• After the “Ready” prompt and the following beep, say
lower priority mobile phone at any time (refer to
“Call”.
“Advanced Phone Connectivity” in this section).
3
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• The system will prompt you to say the name of the • After the “Ready” prompt and the following beep, say
person you want to call.
“Phonebook New Entry”.
• After the “Ready” prompt and the following beep, say • When prompted, say the name of the new entry. Use of
the name of the person you want to call. For example,
long names helps the Voice Command and it is recomyou can say “John Doe”, where John Doe is a previmended. For example, say “Robert Smith” or “Robert”
ously stored name entry in the Uconnect™ phonebook
instead of “Bob”.
or downloaded phonebook. To learn how to store a
• When prompted, enter the number designation (e.g.,
name in the phonebook, refer to “Add Names to Your
“Home”, “Work”, “Mobile”, or “Other”). This will
Uconnect™ Phonebook”, in the phonebook.
allow you to store multiple numbers for each phone• The Uconnect™ system will confirm the name and
book entry, if desired.
then dial the corresponding phone number, which
• When prompted, recite the phone number for the
may appear in the display of certain radios.
phonebook entry that you are adding.
Add Names To Your Uconnect™ Phonebook
After you are finished adding an entry into the phoneNOTE: Adding names to the Uconnect™ Phonebook is book, you will be given the opportunity to add more
recommended when the vehicle is not in motion.
phone numbers to the current entry or to return to the
main menu.
• Press the
button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129
The Uconnect™ Phone will allow you to enter up to 32 • Automatic download and update, if supported, begins
names in the phonebook with each name having up to
as soon as the Bluetooth威 wireless phone connection is
four associated phone numbers and designations. Each
made to the Uconnect™ Phone, for example, after you
language has a separate 32-name phonebook accessible
start the vehicle.
only in that language. In addition, if equipped and
• A maximum of 1000 entries per phone will be downsupported by your phone, Uconnect™ Phone automatiloaded and updated every time a phone is connected
cally downloads your mobile phone’s phonebook.
to the Uconnect™ Phone.
Phonebook Download – Automatic Phonebook
• Depending on the maximum number of entries downTransfer From Mobile Phone
loaded, there may be a short delay before the latest
If equipped and specifically supported by your phone,
downloaded names can be used. Until then, if availUconnect™ Phone automatically downloads names (text
able, the previously downloaded phonebook is availnames) and number entries from your mobile phone’s
able for use.
phonebook. Specific Bluetooth威 Phones with Phone Book
Access Profile may support this feature. See Uconnect™ • Only the phonebook of the currently connected mobile
phone is accessible.
website for supported phones.
• To call a name from the Uconnect™ Phonebook or • Only the mobile phone’s phonebook is downloaded.
downloaded Phonebook, follow the procedure in
SIM card phonebook is not part of the Mobile phone“Call by Saying a Name” section.
book.
3
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• This downloaded phonebook cannot be edited or • Next, choose the number designation (home, work,
deleted on the Uconnect™ Phone. These can only be
mobile, or other) that you wish to edit.
edited on the mobile phone. The changes are trans• When prompted, recite the new phone number for the
ferred and updated to Uconnect™ Phone on the next
phonebook entry that you are editing.
phone connection.
After you are finished editing an entry in the phonebook,
Edit Uconnect™ Phonebook Entries
you will be given the opportunity to edit another entry in
NOTE:
the phonebook, call the number you just edited, or return
• Editing names in the phonebook is recommended to the main menu.
when the vehicle is not in motion.
“Phonebook Edit Entry” can be used to add another
• Automatic downloaded phonebook entries cannot be phone number to a name entry that already exists in the
deleted or edited.
phonebook. For example, the entry John Doe may have a
mobile and a home number, but you can add “John
• Press the
button to begin.
Doe’s” work number later using the “Phonebook Edit
• After the “Ready” prompt and the following beep, say Entry” feature.
“Phonebook Edit Entry”.
Delete Uconnect™ Phonebook Entry
• You will then be asked for the name of the phonebook
NOTE: Editing phonebook entries is recommended
entry that you wish to edit.
when the vehicle is not in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131
• Press the
button to begin.
• Note that only the phonebook entry in the current
language is deleted.
• After the “Ready” prompt and the following beep, say
• Automatic downloaded phonebook entries cannot be
“Phonebook Delete”.
deleted or edited.
• After you enter the Phonebook Delete menu, you will
then be asked for the name of the entry that you wish Delete/Erase “All” Uconnect™ Phonebook Entries
to delete. You can either say the name of a phonebook
button to begin.
• Press the
entry that you wish to delete or you can say “List
Names” to hear a list of the entries in the phonebook • After the “Ready” prompt and the following beep, say
“Phonebook Erase All”.
from which you choose. To select one of the entries
button while the
from the list, press the
• The Uconnect™ Phone will ask you to verify that you
Uconnect™ Phone is playing the desired entry and say
wish to delete all the entries from the phonebook.
“Delete”.
• After confirmation, the phonebook entries will be
• After you enter the name, the Uconnect™ Phone will
deleted.
ask you which designation you wish to delete: home,
work, mobile, other, or all. Say the designation you • Note that only the phonebook in the current language
is deleted.
wish to delete.
3
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• Automatic downloaded phonebook entries cannot be • The selected number will be dialed.
deleted or edited.
Phone Call Features
List All Names In The Uconnect™ Phonebook
The following features can be accessed through the
Uconnect™ Phone if the feature(s) are available on your
button to begin.
• Press the
mobile service plan. For example, if your mobile service
• After the “Ready” prompt and the following beep, say plan provides three-way calling, this feature can be
“Phonebook List Names”.
accessed through the Uconnect™ Phone. Check with
your mobile service provider for the features that you
• The Uconnect™ Phone will play the names of all the
have.
phonebook entries, including the downloaded phoneAnswer Or Reject An Incoming Call — No Call
book entries, if available.
Currently In Progress
• To call one of the names in the list, press the
When you receive a call on your mobile phone, the
button during the playing of the desired name, and
Uconnect™ Phone will interrupt the vehicle audio syssay “Call”.
tem, if on, and will ask if you would like to answer the
button to accept the call. To reject the
NOTE: The user can also exercise “Edit” or “Delete” call. Press the
button until you hear a single
call, press and hold the
operations at this point.
beep, indicating that the incoming call was rejected.
• The Uconnect™ Phone will then prompt you as to the
number designation you wish to call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133
Answer Or Reject An Incoming Call — Call
Currently In Progress
If a call is currently in progress and you have another
incoming call, you will hear the same network tones for
call waiting that you normally hear when using your
button to place the current
mobile phone. Press the
call on hold and answer the incoming call.
in progress. To go back to the first call, refer to “Toggling
Between Calls” in this section. To combine two calls, refer
to “Conference Call” in this section.
Place/Retrieve A Call From Hold
To put a call on hold, press the
button until you hear
a single beep. This indicates that the call is on hold. To
bring the call back from hold, press and hold the
NOTE: The Uconnect™ Phone compatible phones in the button until you hear a single beep.
market today do not support rejecting an incoming call
Toggling Between Calls
when another call is in progress. Therefore, the user can
If two calls are in progress (one active and one on hold),
only answer an incoming call or ignore it.
button until you hear a single beep,
press the
indicating that the active and hold status of the two calls
Making A Second Call While Current Call Is In
Progress
have switched. Only one call can be placed on hold at a
To make a second call while you are currently on a call, time.
press the
button and say “Dial” or “Call” followed
by the phone number or phonebook entry you wish to
call. The first call will be on hold while the second call is
3
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Conference Call
When two calls are in progress (one active and one on
button until you hear a
hold), press and hold the
double beep indicating that the two calls have been
joined into one conference call.
Call Termination
To end a call in progress, momentarily press the
button. Only the active call(s) will be terminated and if
there is a call on hold, it will become the new active call.
If the active call is terminated by the phone far end, a call
on hold may not become active automatically. This is cell
Three-Way Calling
phone-dependent. To bring the call back from hold, press
To initiate three-way calling, press the
button while
button until you hear a single beep.
and hold the
a call is in progress, and make a second phone call, as
described under “Making a Second Call While Current Redial
Call is in Progress”. After the second call has established,
button to begin.
• Press the
button until you hear a double
press and hold the
beep, indicating that the two calls have been joined into • After the “Ready” prompt and the following beep, say
“Redial”.
one conference call.
• The Uconnect™ Phone will call the last number that
was dialed from your mobile phone.
NOTE: This may not be the last number dialed from the
Uconnect™ Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135
Call Continuation
Call continuation is the progression of a phone call on the
Uconnect™ Phone after the vehicle ignition key has been
switched to OFF. Call continuation functionality available on the vehicle can be any one of three types:
Uconnect™ Phone Features
Language Selection
To change the language that the Uconnect™ Phone is
using:
• Press the
button to begin.
• After the ignition key is switched to OFF, a call can
continue on the Uconnect™ Phone either until the call • After the “Ready” prompt and the following beep, say
the name of the language you wish to switch to
ends, or until the vehicle battery condition dictates
English, Espanol, or Francais.
cessation of the call on the Uconnect™ Phone and
transfer of the call to the mobile phone.
• Continue to follow the system prompts to complete
• After the ignition key is switched to OFF, a call can
the language selection.
continue on the Uconnect™ Phone for a certain duraAfter selecting one of the languages, all prompts and
tion, after which the call is automatically transferred
voice commands will be in that language.
from the Uconnect™ Phone to the mobile phone.
NOTE: After every Uconnect™ Phone language change
• An active call is automatically transferred to the
operation, only the language-specific 32-name phonemobile phone after the ignition key is switched to OFF.
book is usable. The paired phone name is not languagespecific and is usable across all languages.
3
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Emergency Assistance
If you are in an emergency and the mobile phone is
reachable:
Canada and 060 for Mexico). The number dialed may
not be applicable with the available mobile service and
area.
• Pick up the phone and manually dial the emergency • If supported, this number may be programmable on
button and say
number for your area.
some systems. To do this, press the
“Setup”, followed by “Emergency”.
If the phone is not reachable and the Uconnect™ Phone is
operational, you may reach the emergency number as • The Uconnect™ Phone does slightly lower your
chances of successfully making a phone call as to that
follows:
for the mobile phone directly.
• Press the
button to begin.
• After the “Ready” prompt and the following beep, say
“Emergency” and the Uconnect™ Phone will instruct
the paired mobile phone to call the emergency number. This feature is supported in the U.S., Canada, and
Mexico.
NOTE:
• The emergency number dialed is based on the country
where the vehicle is purchased (911 for the U.S. and
WARNING!
To use your Uconnect™ Phone System in an emergency, your mobile phone must be:
• turned on,
• paired to the Uconnect™ System,
• and have network coverage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137
Towing Assistance
If you need towing assistance:
Paging
To learn how to page, refer to “Working with Automated
Systems”. Paging works properly except for pagers of
• Press the
button to begin.
certain companies, which time out a little too soon to
• After the “Ready” prompt and the following beep, say work properly with the Uconnect™ Phone.
“Towing Assistance”.
Voice Mail Calling
To learn how to access your voice mail, refer to “Working
NOTE:
• The towing assistance number dialed is based on the with Automated Systems”.
country where the vehicle is purchased (1-800-528Working With Automated Systems
2069 for the U.S., 1-877-213-4525 for Canada, 55-14This method is used in instances where one generally has
3454 for Mexico City and 1-800-712-3040 for outside
to press numbers on the mobile phone keypad while
Mexico City in Mexico). Please refer to the 24-Hour
navigating through an automated telephone system.
“Towing Assistance” coverage details on the DVD in
the Warranty Information Booklet and the 24-Hour You can use your Uconnect™ Phone to access a voice mail
system or an automated service, such as a paging service or
Towing Assistance references.
automated customer service line. Some services require
• If supported, this number may be programmable on
immediate response selection. In some instances, that may
button and say
some systems. To do this, press the
be too quick for use of the Uconnect™ Phone.
“Setup”, followed by “Towing Assistance”.
3
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
When calling a number with your Uconnect™ Phone that
normally requires you to enter in a touch-tone sequence
on your mobile phone keypad, you can press the
button and say the sequence you wish to enter, followed
by the word “Send”. For example, if required to enter
your PIN followed with a pound, (3 7 4 6 #), you can
button and say, “3 7 4 6 # Send”. Saying
press the
a number, or sequence of numbers, followed by “Send”,
is also to be used for navigating through an automated
customer service center menu structure, and to leave a
number on a pager.
You can also send stored Uconnect™ phonebook entries
as tones for fast and easy access to voice mail and pager
entries. To use this feature, dial the number you wish to
button and say, “Send.” The
call and then press the
system will prompt you to enter the name or number and
say the name of the phonebook entry you wish to send.
The Uconnect™ Phone will then send the corresponding
phone number associated with the phonebook entry, as
tones over the phone.
NOTE:
• You may not hear all of the tones due to mobile phone
network configurations. This is normal.
• Some paging and voice mail systems have system time
out settings that are too short and may not allow the
use of this feature.
Barge In — Overriding Prompts
The “Voice Command” button can be used when you
wish to skip part of a prompt and issue your voice
command immediately. For example, if a prompt is
asking “Would you like to pair a phone, clear a...,” you
button and say, “Pair a Phone” to
could press the
select that option without having to listen to the rest of
the voice prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139
Turning Confirmation Prompts ON/OFF
Turning confirmation prompts off will stop the system
from confirming your choices (e.g., the Uconnect™
Phone will not repeat a phone number before you dial it).
Dialing Using The Mobile Phone Keypad
You can dial a phone number with your mobile phone
keypad and still use the Uconnect™ Phone (while dialing
via the mobile phone keypad, the user must exercise
caution and take precautionary safety measures). By
• Press the
button to begin.
dialing a number with your paired Bluetooth威 mobile
• After the “Ready” prompt and the following beep, say phone, the audio will be played through your vehicle’s
one of the following:
audio system. The Uconnect™ Phone will work the same
as if you dial the number using Voice Command.
− “Setup Confirmation Prompts On”
NOTE: Certain brands of mobile phones do not send the
− “Setup Confirmation Prompts Off”
dial ring to the Uconnect™ Phone to play it on the vehicle
Phone And Network Status Indicators
audio system, so you will not hear it. Under this situaIf available on the radio and/or on a premium display tion, after successfully dialing a number the user may feel
such as the instrument panel cluster, and supported by that the call did not go through even though the call is in
your mobile phone, the Uconnect™ Phone will provide progress. Once your call is answered, you will hear the
notification to inform you of your phone and network audio.
status when you are attempting to make a phone call
using Uconnect™ Phone. The status is given for network
signal strength, phone battery strength, etc.
3
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Mute/Un-Mute (Mute OFF)
When you mute the Uconnect™ Phone, you will still be
able to hear the conversation coming from the other
party, but the other party will not be able to hear you. In
order to mute the Uconnect™ Phone:
• Press the
button.
• Following the beep, say “Mute”.
In order to un-mute the Uconnect™ Phone:
• Press the
button.
• Following the beep, say “Mute off”.
Advanced Phone Connectivity
from your Uconnect™ Phone paired mobile phone to the
Uconnect™ Phone or vice versa, press the
button
and say “Transfer Call”.
Connect Or Disconnect Link Between The
Uconnect™ Phone And Mobile Phone
Your mobile phone can be paired with many different
electronic devices, but can only be actively “connected”
with one electronic device at a time.
If you would like to connect or disconnect the Bluetooth威
connection between your mobile phone and the
Uconnect™ Phone System, follow the instructions described in your mobile phone User’s Manual.
List Paired Mobile Phone Names
Transfer Call To And From Mobile Phone
button to begin.
• Press the
The Uconnect™ Phone allows ongoing calls to be transferred from your mobile phone to the Uconnect™ Phone • After the “Ready” prompt and the following beep, say
“Setup Phone Pairing”.
without terminating the call. To transfer an ongoing call
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141
• When prompted, say “List Phones”.
• The selected phone will be used for the next phone
call. If the selected phone is not available, the
• The Uconnect™ Phone will play the phone names of
Uconnect™ Phone will return to using the highest
all paired mobile phones in order from the highest to
priority phone present in or near (approximately
the lowest priority. To “Select” or “Delete” a paired
within 30 ft (9 m)) the vehicle.
button and
phone being announced, press the
say “Select” or “Delete”. Also, see the next two sec- Delete Uconnect™ Phone Paired Mobile Phones
tions for an alternate way to “Select” or “Delete” a
button to begin.
• Press the
paired phone.
• After the “Ready” prompt and the following beep, say
Select Another Mobile Phone
“Setup Phone Pairing”.
This feature allows you to select and start using another
• At the next prompt, say “Delete” and follow the
phone paired with the Uconnect™ Phone.
prompts.
• Press the
button to begin.
• You can also press the
button at any time while the
• After the “Ready” prompt and the following beep, say
list is being played, and then choose the phone you
“Setup Select Phone” and follow the prompts.
wish to delete.
• You can also press the
button at any time while the
list is being played, and then choose the phone that
you wish to select.
3
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Things You Should Know About Your Uconnect™
Phone
Uconnect™ Phone Tutorial
To hear a brief tutorial of the system features, press the
button and say “Uconnect™ Tutorial.”
You can either press the Uconnect™ Phone button to
restore the factory setting or repeat the words and
phrases when prompted by the Uconnect™ Phone. For
best results, the Voice Training session should be completed when the vehicle is parked with the engine
running, all windows closed, and the blower fan
switched off.
Voice Training
For users experiencing difficulty with the system recogThis procedure may be repeated with a new user. The
nizing their voice commands or numbers, the Uconnect™
system will adapt to the last trained voice only.
Phone Voice Training feature may be used. To enter this
training mode, follow one of the two following proce- Reset
dures:
button.
• press the
From outside the Uconnect™ Phone mode (e.g., from
• After the “Ready” prompt, and the following beep, say
radio mode):
“Setup”, then “Reset”.
• Press and hold the
button for five seconds until
This will delete all phone pairing, phone book entries,
the session begins, or,
and other settings in all language modes. The System will
• Press the
button and say the “Voice Training, prompt you before resetting to factory settings.
System Training, or Start Voice Training” command.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143
Voice Command
• fully closed windows,
• dry weather condition.
• For best performance, adjust the rearview mirror to
provide at least 1⁄2 in (1 cm) gap between the overhead
• Even though the system is designed for users speaking
console (if equipped) and the mirror.
in North American English, French, and Spanish ac• Always wait for the beep before speaking.
cents, the system may not always work for some.
• Speak normally, without pausing, just as you would • When navigating through an automated system such
speak to a person sitting a few feet/meters away from
as voice mail, or when sending a page, at the end of
you.
speaking the digit string, make sure to say “Send”.
• Make sure that no one other than you is speaking • Storing names in the phonebook when the vehicle is
during a Voice Command period.
not in motion is recommended.
• Performance is maximized under:
• low-to-medium blower setting,
• low-to-medium vehicle speed,
• low road noise,
• smooth road surface,
• It is not recommended to store similar sounding
names in the Uconnect™ Phonebook.
• Phonebook (Downloaded and Uconnect™ Phone Local) name recognition rate is optimized when the
entries are not similar.
3
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• Numbers must be spoken in single digits. “800” must
be spoken “eight-zero-zero” not “eight hundred”.
• You can say “O” (letter “O”) for “0” (zero).
• fully closed windows,
• dry weather conditions, and
• operation from the driver’s seat.
• Even though international dialing for most number
• Performance, such as audio clarity, echo, and loudness
combinations is supported, some shortcut dialing
to a large degree rely on the phone and network, and
number combinations may not be supported.
not the Uconnect™ Phone.
• In a convertible vehicle, system performance may be
• Echo at the phone far end can sometimes be reduced
compromised with the convertible top down.
by lowering the in-vehicle audio volume.
Far End Audio Performance
• In a convertible vehicle, system performance may be
compromised with the convertible top down.
• Audio quality is maximized under:
• low-to-medium blower setting,
• low-to-medium vehicle speed,
• low road noise,
• smooth road surface,
Recent Calls
If your phone supports “Automatic Phonebook Download”, Uconnect™ Phone can list your Outgoing, Incoming and Missed Calls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145
Send Messages:
SMS
Uconnect™ Phone can read or send new messages on You can send messages using Uconnect™ Phone. To send
a new message:
your phone.
• Press the
button.
Read Messages:
If you receive a new text message while your phone is
• After the “Ready” prompt and the following beep, say
connected to Uconnect™ Phone, an announcement will
“SMS Send” or “Send Message.”
be made to notify you that you have a new text message.
• You can either say the message you wish to send or say
If you wish to hear the new message:
“List Messages.” There are 20 preset messages.
• Press the
button.
button while the
To send a message, press the
• After the “Ready” prompt and the following beep, say
system is listing the message and say “Send.”
“SMS Read” or “Read Messages.”
Uconnect™ Phone will prompt you to say the name or
• Uconnect™ Phone will play the new text message for
number of the person you wish to send the message to.
you.
After reading a message, you can “Reply” or “Forward”
the message using Uconnect™ Phone.
3
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
List of Preset Messages:
11. See You in 15 minutes
1. Yes
12. I am on my way
2. No
13. I’ll be late
3. Where are you?
14. Are you there yet?
4. I need more direction.
15. Where are we meeting?
5. L O L
16. Can this wait?
6. Why
17. Bye for now
7. I love you
18. When can we meet
8. Call me
19. Send number to call
9. Call me later
20. Start without me
10. Thanks
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147
Turn SMS Incoming Announcement ON/OFF
Turning the SMS Incoming Announcement OFF will stop
the system from announcing the new incoming messages.
• Press the
button.
Bluetooth威 Communication Link
Mobile phones have been found to lose connection to the
Uconnect™ Phone. When this happens, the connection
can generally be reestablished by switching the phone
off/on. Your mobile phone is recommended to remain in
Bluetooth威 ON mode.
• After the “Ready” prompt and the following beep, say
Power-Up
“Setup, SMS Incoming Message Announcement,” you
After switching the ignition key from OFF to either the
will then be given a choice to change it.
ON or ACC position, or after a language change, you
must wait at least fifteen seconds prior to using the
system.
3
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149
3
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151
Primary
zero
one
two
three
four
five
six
seven
eight
nine
star (*)
plus (+)
pound (#)
add location
all
Voice Commands
Alternate(s)
Voice Commands
Alternate(s)
Primary
call
cancel
confirmation prompts
continue
delete
dial
download
edit
emergency
English
erase all
Espanol
Francais
help
home
3
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Primary
language
list names
list phones
mobile
mute
mute off
new entry
no
other
pair a phone
phone pairing
phonebook
previous
record again
redial
Voice Commands
Alternate(s)
pairing
phone book
Voice Commands
Primary
Alternate(s)
return to main menu
return or main menu
select phone
select
send
set up
phone settings or phone
set up
towing assistance
transfer call
Uconnect™ Tutorial
try again
voice training
work
yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153
General Information
This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:
• Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
• This device may not cause harmful interference.
• This device must accept any interference received,
including interference that may cause undesired
operation.
VOICE COMMAND — IF EQUIPPED
Voice Command System Operation
This Voice Command system allows you to
control your AM, FM radio, satellite radio, disc
player, and a memo recorder.
NOTE: Take care to speak into the Voice Interface
System as calmly and normally as possible. The ability of
the Voice Interface System to recognize user voice commands may be negatively affected by rapid speaking or a
raised voice level.
WARNING!
Any voice commanded system should be used only
in safe driving conditions following local laws. All
attention should be kept on the roadway ahead.
Failure to do so may result in a collision causing
serious injury or death.
button, you
When you press the Voice Command
will hear a beep. The beep is your signal to give a
command.
NOTE: If you do not say a command within a few
seconds, the system will present you with a list of options.
3
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
If you ever wish to interrupt the system while it lists The system will best recognize your speech if the winbutton, listen dows are closed, and the heater/air conditioning fan is
options, press the Voice Command
set to low.
for the beep, and say your command.
button while the
Pressing the Voice Command
system is speaking is known as “barging in.” The system
will be interrupted, and after the beep, you can add or
change commands. This will become helpful once you
start to learn the options.
At any point, if the system does not recognize one of your
commands, you will be prompted to repeat it.
To hear the first available Menu, press the Voice Combutton and say “Help” or “Main Menu”.
mand
Commands
NOTE: At any time, you can say the words “Cancel”,
The Voice Command system understands two types of
“Help” or “Main Menu”.
commands. Universal commands are available at all
These commands are universal and can be used from any times. Local commands are available if the supported
menu. All other commands can be used depending upon radio mode is active.
the active application.
Changing the Volume
When using this system, you should speak clearly and at
1. Start a dialogue by pressing the Voice Command
a normal speaking volume.
button.
2. Say a command (e.g., “Help”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155
3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM
volume to a comfortable level while the Voice Command To switch to the AM band, say “AM” or “Radio AM”. In
system is speaking. Please note the volume setting for this mode, you may say the following commands:
Voice Command is different than the audio system.
• “Frequency #” (to change the frequency)
Main Menu
• “Next Station” (to select the next station)
Start a dialogue by pressing the Voice Command
button. You may say “Main Menu” to switch to the main • “Previous Station” (to select the previous station)
menu.
• “Radio Menu” (to switch to the radio menu)
In this mode, you can say the following commands:
• “Main Menu” (to switch to the main menu)
• “Radio” (to switch to the radio mode)
Radio FM
• “Disc” (to switch to the disc mode)
To switch to the FM band, say “FM” or “Radio FM”. In
this mode, you may say the following commands:
• “Memo” (to switch to the memo recorder)
• “Frequency #” (to change the frequency)
• “Setup” (to switch to system setup)
• “Next Station” (to select the next station)
• “Previous Station” (to select the previous station)
3
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• “Menu Radio” (to switch to the radio menu)
• “Main Menu” (to switch to the main menu)
Disc
To switch to the disc mode, say “Disc”. In this mode, you
may say the following commands:
Satellite Radio
• “Track” (#) (to change the track)
To switch to satellite radio mode, say “Sat” or “Satellite
Radio”. In this mode, you may say the following com- • “Next Track” (to play the next track)
mands:
• “Previous Track” (to play the previous track)
• “Channel Number” (to change the channel by its
• “Main Menu” (to switch to the main menu)
spoken number)
Memo
• “Next Channel” (to select the next channel)
To switch to the voice recorder mode, say “Memo”. In
• “Previous Channel” (to select the previous channel)
this mode, you may say the following commands:
• “List Channel” (to hear a list of available channels)
• “Select Name” (to say the name of a channel)
• “Menu Radio” (to switch to the radio menu)
• “Main Menu” (to switch to the main menu)
• “New Memo” (to record a new memo) — During the
recording, you may press the Voice Command
button to stop recording. You proceed by saying one of
the following commands:
− “Save” (to save the memo)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157
− “Continue” (to continue recording)
• “Switch to system setup”
− “Delete” (to delete the recording)
• “Change to setup”
• “Play Memos” (to play previously recorded memos) • “Main menu setup” or
— During the playback you may press the Voice
• “Switch to setup”
button to stop playing memos. You
Command
proceed by saying one of the following commands:
In this mode, you may say the following commands:
− “Repeat” (to repeat a memo)
• “Language English”
− “Next” (to play the next memo)
• “Language French”
− “Previous” (to play the previous memo)
• “Language Spanish”
− “Delete” (to delete a memo)
• “Tutorial”
• “Delete All” (to delete all memos)
• “Voice Training”
Setup
NOTE: Keep in mind that you have to press the Voice
To switch to system setup, you may say on of the Command
button first and wait for the beep before
following:
speaking the “Barge In” commands.
• “Change to setup”
3
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Voice Training
For users experiencing difficulty with the system recognizing their voice commands or numbers the Uconnect™
Voice “Voice Training” feature may be used.
button, say “System
1. Press the Voice Command
Setup” and once you are in that menu then say “Voice
Training.” This will train your own voice to the system
and will improve recognition.
WARNING!
• It is dangerous to ride in a cargo area, inside or
outside of a vehicle. In a collision, people riding in
these areas are more likely to be seriously injured
or killed.
• Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat
belts. In a collision, people riding in these areas
are more likely to be seriously injured or killed.
• Be sure everyone in your vehicle is in a seat and
using a seat belt properly.
2. Repeat the words and phrases when prompted by
Uconnect™ Voice. For best results, the “Voice Training”
session should be completed when the vehicle is parked,
engine running, all windows closed, and the blower fan
switched off. This procedure may be repeated with a new Power Seats — If Equipped
user. The system will adapt to the last trained voice only. Some models may be equipped with eight-way power
driver and front passenger seats. The power seat switches
SEATS
are located on the outboard side of the seat. There are two
Seats are part of the Occupant Restraint System of the
switches that control the movement of the seat cushion
vehicle.
and the seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159
Adjusting The Seat Forward Or Rearward
The seat can be adjusted both forward and rearward.
Push the seat switch forward or rearward, the seat will
move in the direction of the switch. Release the switch
when the desired position has been reached.
Adjusting The Seat Up Or Down
The height of the seats can be adjusted up or down. Pull
upward or push downward on the rear of the seat switch,
the seat will move in the direction of the switch. Release
the switch when the desired position has been reached.
Power Seat Switches
1 — Seatback Switch
2 — Seat Switch
Tilting The Seat Up Or Down
The angle of the seat cushion can be adjusted up or
down. Pull upward or push downward on the front of
the seat switch, the front of the seat cushion will move in
the direction of the switch. Release the switch when the
desired position has been reached.
3
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Reclining The Seatback
The angle of the seatback can be adjusted forward or
backward. Push the seatback switch forward or rearward, the seat will move in the direction of the switch.
Release the switch when the desired position has been
reached.
• Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your
chest. In a collision you could slide under the seat
belt, which could result in serious injury or death.
WARNING!
CAUTION!
• Adjusting a seat while driving may be dangerous.
Moving a seat while driving could result in loss of
control which could cause a collision and serious
injury or death.
• Seats should be adjusted before fastening the seat
belts and while the vehicle is parked. Serious
injury or death could result from a poorly adjusted
seat belt.
Do not place any article under a power seat or
impede its ability to move as it may cause damage to
the seat controls. Seat travel may become limited if
movement is stopped by an obstruction in the seat’s
path.
WARNING! (Continued)
Passenger’s Power Seat — If Equipped
Some models are equipped with a six-way power pas(Continued) senger seat. The power seat switch is located on the
outboard side of the seat. The switch is used to control
the movement of the seat and seat cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161
Adjusting The Seat Forward Or Rearward
The seat can be adjusted both forward and rearward.
Push the seat switch forward or rearward, the seat will
move in the direction of the switch. Release the switch
when the desired position has been reached.
Adjusting The Seat Up Or Down
The height of the seats can be adjusted up or down. Pull
upward or push downward on the seat switch, the seat
will move in the direction of the switch. Release the
switch when the desired position has been reached.
Tilting The Seat Up Or Down
The angle of the seat cushion can be adjusted up or
down. Pull upward or push downward on the front of
the seat switch, the front of the seat cushion will move in
the direction of the switch. Release the switch when the
desired position has been reached.
WARNING!
• Adjusting a seat while driving may be dangerous.
Moving a seat while driving could result in loss of
control which could cause a collision and serious
injury or death.
• Seats should be adjusted before fastening the seat
belts and while the vehicle is parked. Serious
injury or death could result from a poorly adjusted
seat belt.
• Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your
chest. In a collision you could slide under the seat
belt, which could result in serious injury or death.
3
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CAUTION!
Do not place any article under a power seat or
impede its ability to move as it may cause damage to
the seat controls. Seat travel may become limited if
movement is stopped by an obstruction in the seat’s
path.
Power Lumbar — If Equipped
Vehicles equipped with power driver or passenger seats
may be also be equipped with power lumbar. The power
lumbar switch is located on the outboard side of the
power seat. Push the switch forward to increase the
lumbar support. Push the switch rearward to decrease
the lumbar support. Pushing upward or downward on
the switch will raise and lower the position of the
support.
Power Lumbar Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163
Manual Front Passenger Seat Forward/Rearward
Adjustment
Some models may be equipped with a manual front
passenger seat. The passenger seat can be adjusted forward or rearward by using a bar located by the front of
the seat cushion, near the floor.
While sitting in the seat, lift up on the bar located under
the seat cushion and move the seat forward or rearward.
Release the bar once you have reached the desired
position. Then, using body pressure, move forward and
rearward on the seat to be sure that the seat adjusters
have latched.
WARNING!
• Adjusting a seat while driving may be dangerous.
Moving a seat while driving could result in loss of
control which could cause a collision and serious
injury or death.
• Seats should be adjusted before fastening the seat
belts and while the vehicle is parked. Serious
injury or death could result from a poorly adjusted
seat belt.
Adjustment Bar
3
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Manual Front Passenger Seatback Adjustment —
Recline
To adjust the seatback, lift the lever located on the
outboard side of the seat, lean back to the desired
position and release the lever. To return the seatback, lift
the lever, lean forward and release the lever.
WARNING!
Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your chest.
In a collision you could slide under the seat belt,
which could result in serious injury or death.
Front Passenger Seat Fold-Flat Feature —
If Equipped
To fold the seatback to the flat load-floor position, lift the
recline lever and push the seatback forward. To return to
the seating position, raise the seatback and lock it into
place.
Recline Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165
WARNING!
Fold-Flat Passenger Seat
• Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise
care when using the seat heater. It may cause burns
even at low temperatures, especially if used for
long periods of time.
• Do not place anything on the seat that insulates
against heat, such as a blanket or cushion. This
may cause the seat heater to overheat. Sitting in a
seat that has been overheated could cause serious
burns due to the increased surface temperature of
the seat.
Heated Seats — If Equipped
On some models, the front and rear seats may be
equipped with heaters in both the seat cushions and
seatbacks.
Vehicles Equipped With Remote Start
On models that are equipped with remote start, the
driver’s heated seat can be programmed to come on
3
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
during a remote start. Refer to “Remote Starting System NOTE: Once a heat setting is selected, heat will be felt
— If Equipped” in “Things To Know Before Starting Your within two to five minutes.
Vehicle” for further information.
When the HIGH-level setting is selected, the heater will
Front Heated Seats
provide a boosted heat level during the first four minutes
There are two heated seat switches that allow the driver of operation. Then, the heat output will drop to the
and passenger to operate the seats independently. The normal HIGH-level. If the HIGH-level setting is selected,
controls for each heater are located near the bottom the system will automatically switch to LOW-level after a
center of the instrument panel (below the climate con- maximum of 50 minutes of continuous operation. At that
time, the number of illuminated LEDs changes from two
trols).
to one, indicating the change. The LOW-level setting will
You can choose from HIGH, LOW or OFF heat settings.
turn OFF automatically after a maximum of 45 minutes.
Amber indicator lights in each switch indicate the level of
heat in use. Two indicator lights will illuminate for Rear Heated Seats
On some models, the two outboard seats are equipped
HIGH, one for LOW and none for OFF.
with heated seats. There are two heated seat switches that
Press the switch once to select HIGH-level
allow the rear passengers to operate the seats indepenheating. Press the switch a second time to select
dently. The heated seat switches for each heater are
LOW-level heating. Press the switch a third
located on the rear of the center console.
time to shut the heating elements OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167
Press the switch once to select HIGH-level
heating. Press the switch a second time to select
LOW-level heating. Press the switch a third
time to shut the heating elements OFF.
NOTE: Once a heat setting is selected, heat will be felt
within two to five minutes.
When the HIGH-level setting is selected, the heater will
provide a boosted heat level during the first four minutes
of operation. Then, the heat output will drop to the
normal HIGH-level. If the HIGH-level setting is selected,
the system will automatically switch to LOW-level after a
Rear Heated Seat Switches
maximum of 50 minutes of continuous operation. At that
You can choose from HIGH, LOW or OFF heat settings. time, the number of illuminated LEDs changes from two
Amber indicator lights in each switch indicate the level of to one, indicating the change. The LOW-level setting will
heat in use. Two indicator lights will illuminate for turn OFF automatically after a maximum of 45 minutes.
HIGH, one for LOW and none for OFF.
3
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Ventilated Seats — If Equipped
On some models, both the driver and passenger seats are
ventilated. Located in the seat cushion and seatback are
small fans that draw the air from the passenger compartment and blow air through fine perforations in the seat
cover to help keep the driver and front passenger cooler
in higher ambient temperatures.
There are two ventilated seat switches that allow the
driver and passenger to operate the seats independently.
The ventilated seat switches are located on the switch
bank in the center stack of the instrument panel, just
below the climate controls.
The ventilated seat switches are used
to control the speed of the fans located
in the seat. Press the switch once to
choose HIGH, press it a second time to
choose LOW. Pressing the switch a
third time will turn the ventilated seat
OFF. When HIGH speed is selected both lights on the
switch will be illuminated. When LOW speed is selected
one light will be illuminated.
NOTE: The engine must be running for the ventilated
seats to operate.
Vehicles Equipped With Remote Start
On models that are equipped with remote start, the
driver’s ventilated seat can be programmed to come on
during a remote start. Refer to “Remote Starting System
— If Equipped” in “Things to Know Before Starting Your
Vehicle” for further information.
Head Restraints
Head restraints are designed to reduce the risk of injury
by restricting head movement in the event of a rearimpact. Head restraints should be adjusted so that the top
of the head restraint is located above the top of your ear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169
WARNING!
The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a
vehicle with the head restraints improperly adjusted
or removed could cause serious injury or death in the
event of a collision.
Active Head Restraints — Front Seats
Active Head Restraints are passive, deployable components, and vehicles with this equipment cannot be readily
identified by any markings, only through visual inspection of the head restraint. The head restraint will be split
in two halves, with the front half being soft foam and
trim, the back half being decorative plastic.
When AHRs deploy during a rear impact, the front half
of the head restraint extends forward to minimize the gap
between the back of the occupant’s head and the AHR.
This system is designed to help prevent or reduce the
extent of injuries to the driver and front passenger in
certain types of rear impacts. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information.
3
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To raise the head restraint, pull upward on the head
restraint. To lower the head restraint, press the push
button, located at the base of the head restraint, and push
downward on the head restraint.
For comfort the Active Head Restraints can be tilted
forward and rearward. To tilt the head restraint closer to
the back of your head, pull forward on the bottom of the
head restraint. Push rearward on the bottom of the head
restraint to move the head restraint away from your
head.
Push Button
Active Head Restraint (Normal Position)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171
• In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active
Head Restraints (AHR)” in “Things To Know Before
Starting Your Vehicle” for further information.
WARNING!
Active Head Restraint (Tilted)
NOTE:
• The head restraints should only be removed by qualified technicians, for service purposes only. If either of
the head restraints require removal, see your authorized dealer.
3
• Do not place items over the top of the Active Head
Restraint, such as coats, seat covers or portable
DVD players. These items may interfere with the
operation of the Active Head Restraint in the event
of a collision and could result in serious injury or
death.
(Continued)
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING! (Continued)
• Active Head Restraints may be deployed if they
are struck by an object such as a hand, foot or loose
cargo. To avoid accidental deployment of the Active Head Restraint ensure that all cargo is secured, as loose cargo could contact the Active Head
Restraint during sudden stops. Failure to follow
this warning could cause personal injury if the
Active Head Restraint is deployed.
Head Restraints — Rear Seats
The head restraints on the outboard seats are not adjustable. They automatically fold forward when the rear seat
is folded to a load floor position but do not return to their
normal position when the rear seat is raised. After
returning either seat to its upright position, raise the head
restraint until it locks in place. The outboard headrests
are not removable.
The center head restraint has limited adjustment. Lift
upward on the head restraint to raise it, or push downward on the head restraint to lower it.
Rear Head Restraint
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173
WARNING!
Sitting in a seat with the head restraint in its lowered
position could result in serious injury or death in a
collision. Always make sure the outboard head restraints are in their upright positions when the seat is
to be occupied.
Press the power folding switch located
on the instrument panel to fold the
head restraints.
NOTE:
NOTE: For proper routing of a Child Seat Tether refer to • The head restraints can only be folded downward
using the power folding switch. The head restraints
“Occupant Restraints” in “Things to Know Before Startmust be raised manually when occupying the third
ing Your Vehicle” for further information.
row.
Power Folding Third Row Head Restraints
For improved visibility when in reverse, the third row • Do not fold if there are passengers seated in the third
row seats.
head restraints can be folded using a switch, located on
the instrument panels switch bank.
3
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
60/40 Split Rear Seat — If Equipped
Fold-Flat
The second row seats can be folded flat to carry cargo.
Pull upward on the release lever located on the outboard
side of the seat.
Fold-Flat Second Row Seat
Easy Access For Third Row
Either side of the rear seat can be tumbled forward to
allow passengers to easily access the third row seats.
1. Pull upward on the release lever to release the seat.
Release Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175
3
Release Lever
2. Tumble the seat forward using the pull strap located
behind the seatback.
Tumble Strap
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
Do not drive the vehicle with the second row seats in
the tumbled position. The second row seats are only
intended to be tumbled for entry and exit to the third
row seat. Failure to follow these instructions could
result in personal injury.
To Raise Rear Seat
Tumbled the seat rearward and lock it into place.
WARNING!
Tumbled Second Row
Be certain that the seatback is securely locked into
position. If the seatback is not securely locked into
position the seat will not provide the proper stability
for child seats and/or passengers. An improperly
latched seat could cause serious injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177
Rear Captain Chairs — If Equipped
Fold-Flat
The second row seats can be folded flat to carry cargo.
Pull upward on the release lever located on the outboard
side of the seat.
3
Fold-Flat Second Row Seats
Release Lever
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
2. Tumble the seat forward using the pull strap located
Easy Access For Third Row
Either captains chair can be tumbled forward to allow behind the seatback.
passengers to easily access the third row seats.
1. Pull upward on the release lever to release the seat.
Tumble Strap
Release Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179
WARNING!
Do not drive the vehicle with the second row seats in
the tumbled position. The second row seats are only
intended to be tumbled for entry and exit to the third
row seat. Failure to follow these instructions could
result in personal injury.
3
3. If your vehicle is equipped with a mini console there is
a stepping pad to allow passengers to easily access the
third row seats.
Mini Console Stepping Pad
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To Raise Rear Seat
Tumbled the seat rearward and lock it into place.
WARNING!
Be certain that the seatback is securely locked into
position. If the seatback is not securely locked into
position the seat will not provide the proper stability
for child seats and/or passengers. An improperly
latched seat could cause serious injury.
Folding Third Row
Both third row seats can be folded forward to increase the
cargo area. To lower either seat pull on the release handle
located on back of the seat and lower the seat using the
pull strap located next to the release handle.
Release Handles
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181
NOTE: The second row seats must be in their full
upright position, or tumbled when folding the third row
seats.
To raise the seat, pull the seat toward you using the strap
located on the back of the seat.
WARNING!
Third Row Folded
Be certain that the seatback is securely locked into
position. If the seatback is not securely locked into
position the seat will not provide the proper stability
for child seats and/or passengers. An improperly
latched seat could cause serious injury.
3
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
DRIVER MEMORY SEAT — IF EQUIPPED
Once programmed, the memory buttons 1 and 2 on the
driver’s door panel can be used to recall the driver’s seat,
driver’s outside mirror, adjustable steering wheel position (if equipped), and the radio station preset settings.
Your Remote Keyless Entry (RKE) transmitters can also
be programmed to recall the same positions when the
UNLOCK button is pressed.
Driver Memory Buttons
Your vehicle is equipped with two RKE transmitters. One
or both RKE transmitters can be linked to either memory
position. The memory system can accommodate up to
four RKE transmitters, each one linked to either of the
two memory positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183
Setting Memory Positions And Linking Remote
Keyless Entry Transmitter To Memory
5. Turn on the radio and set the radio station presets (up
to 12 AM and 12 FM stations can be set).
NOTE: Each time the S (SET) button and a numbered 6. Turn the ignition switch to the LOCK/OFF position
button 1 or 2 are pressed, you erase the memory settings and remove the key.
for that button and store a new one.
7. Press and release the S (SET) button located on the
1. Insert the ignition key, and turn the ignition switch to driver’s door.
the ON/RUN position.
8. Within five seconds, press and release MEMORY
2. Press the driver door MEMORY button number 1 if button 1 or 2 on the driver’s door. The next step must be
you are setting the memory for driver 1, or button performed within five seconds if you desire to also use a
number 2 if you are setting the memory for driver 2. The RKE transmitter to recall memory positions.
system will recall any stored settings. Wait for the system
9. Press and release the LOCK button on one of the RKE
to complete the memory recall before continuing to
transmitters.
Step 3.
10. Insert the ignition key, and turn the ignition switch to
3. Adjust the driver’s seat, recliner, and driver’s sideview
the ON/RUN position.
mirror to the desired positions.
11. Select ⬙Remote Linked to Memory⬙ in the Electronic
4. Adjust the power steering column tilt and telescoping
Vehicle Information Center (EVIC) and enter ⬙Yes⬙. Refer
position (if equipped) to the desired positions.
3
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
to “Electronic Vehicle Information Center (EVIC)/ To recall the memory setting for driver two, press
Customer-Programmable Features” in “Understanding MEMORY button number 2 on the driver’s door, or the
UNLOCK button on the RKE transmitter linked to
Your Instrument Panel” for further information.
memory position 2.
12. Repeat the above steps to set the next memory
position, using the other numbered memory button, or to A recall can be cancelled by pressing any of the
MEMORY buttons on the drivers door during a recall (S,
link another RKE transmitter to memory.
1, or 2). When a recall is cancelled, the driver’s seat,
Memory Position Recall
driver’s mirror and the pedals stop moving. A delay of
NOTE: The vehicle must be in PARK to recall memory one second will occur before another recall can be
positions. If a recall is attempted when the vehicle is not selected.
in PARK, a message will be displayed in the Electronic
To Disable A RKE Transmitter Linked To Memory
Vehicle Information Center (EVIC).
1. Turn the ignition switch to the LOCK position, and
To recall the memory settings for driver one, press
remove the key.
MEMORY button number 1 on the driver’s door, or the
UNLOCK button on the RKE transmitter linked to 2. Press and release MEMORY button number 1. The
system will recall any memory settings stored in position
memory position 1.
1. Wait for the system to complete the memory recall
before continuing to Step 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185
3. Press and release the memory S (SET) button located Easy Entry/Exit Seat
This feature provides automatic driver’s seat positioning
on the driver’s door.
which will enhance driver mobility out of and into the
4. Within five seconds, press and release MEMORY
vehicle.
button 1 on the driver’s door.
There are two possible Easy Entry/Exit adjustments
5. Within five seconds, press and release the UNLOCK
available:
button on the RKE transmitter.
• The seat cushion will move rearward approximately
To disable another RKE transmitter linked to either
2.5 in (60 mm), if the starting position of the seat is
memory position, repeat steps 1 through 5 for each RKE
greater than or equal to 2.67 in (68 mm) forward of the
transmitter.
rear seat stop when the key is removed from the
ignition switch. The seat will then move forward
NOTE: Once programmed, all RKE transmitters linked
approximately 2.5 in (60 mm) when the key is placed
to memory can be easily enabled or disabled at one time.
into the ignition and turned out of the LOCK position.
Refer to “Electronic Vehicle Information Center (EVIC)/
Customer-Programmable Features” in “Understanding
• The seat will move to the position located 0.3 in
Your Instrument Panel” for further information.
(8 mm) forward of the rear stop if the starting position
is between 0.9 to 2.67 in (23 to 68 mm) forward of the
rear stop when the key is removed from the ignition
switch. The seat will move forward to the memory/
3
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
driving position when the key is placed into the TO OPEN AND CLOSE THE HOOD
ignition, and turned out of the LOCK position toward To open the hood, two latches must be released.
the ACC/ON position.
1. Pull the release lever located below the instrument
The Easy Entry/Exit feature will be automatically dis- panel and in front of the driver’s door.
abled if the seat is already positioned closer than 0.9 in
(23 mm) forward of the rear stop. At this position, there
is no benefit to the driver by moving the seat for Easy
Exit/Entry.
Each stored memory setting will have an associated Easy
Entry/Exit position.
NOTE: The Easy Entry/Exit feature is not enabled
when the vehicle is delivered from the factory. The Easy
Entry/Exit feature is enabled (or later disabled) through
the programmable features in the Electronic Vehicle
Information Center (EVIC). Refer to “Electronic Vehicle
Information Center (EVIC)/Customer-Programmable
Features” in “Understanding Your Instrument Panel” for
further information.
Hood Release
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187
2. Reach under the hood from outside the vehicle, move
the safety latch to the left and lift the hood.
CAUTION!
To prevent possible damage, do not slam the hood to
close it. Use a firm downward push at the center of
the hood to ensure that both latches engage.
3
WARNING!
Be sure the hood is fully latched before driving your
vehicle. If the hood is not fully latched, it could open
when the vehicle is in motion and block your vision.
Failure to follow this warning could result in serious
injury or death.
Safety Latch Location
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To turn on the headlights, rotate the headlight
LIGHTS
switch clockwise. When the headlight switch is
Headlight Switch
on the parking lights, taillights, license plate
The headlight switch is located on the left side of the
light and instrument panel lights are also
instrument panel, next to the steering wheel. The headturned
on.
To turn off the headlights, rotate the headlight
light switch controls the operation of the headlights,
switch
back
to the O (Off) position.
parking lights, instrument panel lights, cargo lights and
fog lights (if equipped).
NOTE:
• Your vehicle is equipped with plastic headlight and
fog light (if equipped) lenses that are lighter and less
susceptible to stone breakage than glass lights. Plastic
is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
• To minimize the possibility of scratching the lenses
and reducing light output, avoid wiping with a dry
cloth. To remove road dirt, wash with a mild soap
solution followed by rinsing.
Headlight Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189
Headlights On Automatically With Wipers
If your vehicle is equipped with Automatic Headlights, it
Do not use abrasive cleaning components, solvents, also has this customer-programmable feature. When
steel wool or other abrasive materials to clean the your headlights are in the automatic mode and the
engine is running, they will automatically turn on when
lenses.
the wiper system is on. Refer to “Electronic Vehicle
Information Center (EVIC)/Customer-Programmable
Automatic Headlights — If Equipped
This system automatically turns the headlights on or off Features” in “Understanding Your Instrument Panel” for
according to ambient light levels. To turn the system on, further information.
rotate the headlight switch to the A (AUTO) position.
If your vehicle is equipped with a “Rain Sensitive Wiper
When the system is on, the Headlight Delay feature is System” and it is activated, the headlights will automatialso on. This means the headlights will stay on for up to cally turn on after the wipers complete five wipe cycles
90 seconds after you turn the ignition switch to the OFF within approximately one minute, and they will turn off
position. To turn the automatic headlights off, turn the approximately four minutes after the wipers completely
stop. Refer to “Windshield Wipers and Washers” in this
headlight switch out of the AUTO position.
section for further information.
NOTE: The engine must be running before the headlights will turn on in the Automatic Mode.
CAUTION!
3
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: When your headlights come on during the To Activate
daytime, the instrument panel lights will automatically
1. Enable the Automatic High Beams. Refer to “Elecdim to the lower nighttime intensity. Refer to “Lights” in
tronic Vehicle Information Center (EVIC)/Customerthis section for further information.
Programmable Features” in “Understanding Your InstruSmartBeam™ — If Equipped
ment Panel” for further information.
The SmartBeam™ system provides increased forward
2. Turn the headlight switch to the AUTO headlight
lighting at night by automating high beam control
position.
through the use of a digital camera mounted on the
inside rearview mirror. This camera detects vehicle spe- 3. Push the multifunction lever away from you (toward
cific light and automatically switches from high beams to front of vehicle) to engage the high beam mode.
low beams until the approaching vehicle is out of view.
NOTE: This system will not activate until the vehicle is
NOTE: If the windshield or SmartBeam™ mirror is at or above 20 mph (32 km/h).
replaced, the SmartBeam™ mirror must be re-aimed to
To Deactivate
ensure proper performance. See your local authorized
1. Pull the multifunction lever toward you (or rearward
dealer.
in car) to manually deactivate the system (normal operation of low beams).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191
2. Push back on the multifunction lever once again to Headlight Delay
To aid in your exit, your vehicle is equipped with a
reactivate the system.
headlight delay that will leave the headlights on for
NOTE: Broken, muddy, or obstructed headlights and
approximately 90 seconds. This delay is initiated when
taillights of vehicles in the field of view will cause
the ignition is turned OFF while the headlight switch is
headlights to remain on longer (closer to the vehicle).
on, and then the headlight switch is cycled off. Headlight
Also, dirt, film, and other obstructions (sticker, toll box,
delay can be cancelled by either turning the headlight
etc.) on the windshield or camera lens will cause the
switch on then off, or by turning the ignition ON.
system to function improperly.
The headlight delay time is programmable on vehicles
Daytime Running Lights — If Equipped
The Daytime Running Lights (low intensity) come on equipped with an Electronic Vehicle Information Center
whenever the engine is running, and the transmission is (EVIC). Refer to “Electronic Vehicle Information Center
not in the PARK position. The lights will remain on until (EVIC)/Customer-Programmable Features” in “Underthe ignition is switched to the OFF or ACC position or the standing Your Instrument Panel” for further information.
parking brake is engaged. Also, if a turn signal is Parking Lights And Panel Lights
activated, the DRL lamp on the same side of the vehicle
To turn on the parking lights and instrument panel
will turn off for the duration of the turn signal activation.
lights, rotate the headlight switch clockwise. To
Once the turn signal is no longer active, the DRL lamp turn off the parking lights, rotate the headlight switch
will illuminate. The headlight switch must be used for back to the O (Off) position.
normal nighttime driving.
3
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Fog Lights — If Equipped
The fog lights are turned on by rotating the headlight
switch to the parking light or headlight position and
pushing in the headlight rotary control.
Fog Light Operation
The fog lights will operate only when the parking lights
are on or when the vehicle headlights are on low beam.
An indicator light located in the instrument cluster will
illuminate when the fog lights are on. The fog lights will
turn off when the switch is pushed a second time, when
the headlight switch is rotated to the off position, or the
high beam is selected.
Interior Lights
Courtesy and dome lights are turned on when the front
doors are opened, when the dimmer control (rotating
wheel on the right side of the headlight switch) is rotated
to the its farthest upward position, or if equipped, when
the UNLOCK button is pressed on the Remote Keyless
Entry (RKE) transmitter. When a door is open and the
interior lights are on, rotating the dimmer control all the
way down, to the OFF detent, will cause all the interior
lights to go out. This is also known as the “Party” mode
because it allows the doors to stay open for extended
periods of time without discharging the vehicle’s battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193
The brightness of the instrument panel lighting can be
regulated by rotating the dimmer control up (brighter) or
down (dimmer). When the headlights are on you can
supplement the brightness of the odometer, trip odometer, radio, overhead console, rear full center console
cubby bin (if equipped) and lighted cupholders (if
equipped) by rotating the control to its farthest position
up until you hear a click. This feature is termed the
“Parade” mode and is useful when headlights are required during the day.
3
Dimmer Control
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: Battery saver mode is cancelled if the ignition is
Lights-On Reminder
If the headlights, parking lights, or cargo lights are left on ON.
after the ignition is turned OFF, a chime will sound when
Front Map/Reading Lights
the driver’s door is opened.
The front map/reading lights are mounted in the overBattery Saver
head console.
To protect the life of your vehicle’s battery, load shedding
is provided for both the interior and exterior lights.
If the ignition is OFF and any door is left ajar for
10 minutes or the dimmer control is rotated all the way
up to the dome ON position for 10 minutes, the interior
lights will automatically turn off.
If the headlights remain on while the ignition is cycled
OFF, the exterior lights will automatically turn off after
eight minutes. If the headlights are turned on and left on
for eight minutes while the ignition is OFF, the exterior
lights will automatically turn off.
Front Map/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195
Each light can be turned on by pressing a switch on either
side of the console. These buttons are backlit for night
time visibility. To turn the lights off, press the switch a
second time. The lights will also turn on when the
UNLOCK button on the Remote Keyless Entry (RKE) is
pressed.
Courtesy Lights
The courtesy lights can be turned on by pressing the top
corner of the lens. To turn the lights off, press the lens a
second time.
3
Courtesy Lights
Front Map/Reading Light Switches
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Ambient Light
Multifunction Lever
The overhead console is equipped with an ambient light The multifunction lever is located on the left side of the
feature. This light casts illumination for improved visibil- steering column.
ity of the floor center console and PRNDL area.
Multifunction Lever
Ambient Light
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197
Turn Signals
Move the multifunction lever up or down and the arrows
on each side of the instrument cluster flash to show
proper operation of the front and rear turn signal lights.
NOTE: If either light remains on and does not flash, or
there is a very fast flash rate, check for a defective outside
light bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is
defective.
Lane Change Assist
Tap the lever up or down once, without moving beyond
the detent, and the turn signal (right or left) will flash
three times then automatically turn off.
Flash-To-Pass
You can signal another vehicle with your headlights by
partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to
turn on until the lever is released.
High/Low Beam Switch
Push the multifunction lever toward the instrument
panel to switch the headlights to high beam. Pulling the
multifunction back toward the steering wheel will turn
the low beams back on, or shut the high beams off.
3
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WINDSHIELD WIPERS AND WASHERS
The windshield wiper/washer control lever is located on
the left side of the steering column. The front wipers are
operated by rotating a switch, located on the end of the
lever. For information on the rear wiper/washer, refer to
“Rear Window Features” in “Understanding The Features Of Your Vehicle”.
Windshield Wiper Operation
Rotate the end of the lever to one of the first four detent
positions for intermittent settings, the fifth detent for low
wiper operation and the sixth detent for high wiper
operation.
Windshield Wiper Operation
Windshield Wiper/Washer Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199
CAUTION!
Always remove any buildup of snow that prevents
the windshield wiper blades from returning to the
“park” position. If the windshield wiper switch is
turned off, and the blades cannot return to the “park”
position, damage to the wiper motor may occur.
Intermittent Wiper System
Use one of the four intermittent wiper settings when
weather conditions make a single wiping cycle, with a
variable delay between cycles, desirable. At driving
Intermittent Wiper Operation
speeds above 10 mph (16 km/h), the delay can be
regulated from a maximum of approximately 18 seconds NOTE: If the vehicle is moving less than 10 mph
between cycles (first detent), to a cycle every one second (16 km/h), delay times will be doubled.
(fourth detent).
3
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
If the end of the lever is pushed while the wipers are in
Windshield Washer Operation
To use the washer, push on the end of the lever (toward the off position, the wipers will operate for several wipe
the steering wheel) and hold while spray is desired. If the cycles, then turn off.
lever is pushed while in the intermittent setting, the
WARNING!
wipers will turn on and operate for several wipe cycles
after the end of the lever is released, and then resume the
Sudden loss of visibility through the windshield
intermittent interval previously selected.
could lead to a collision. You might not see other
vehicles or other obstacles. To avoid sudden icing of
the windshield during freezing weather, warm the
windshield with the defroster before and during
windshield washer use.
Mist
Use the Mist feature when weather conditions make
occasional usage of the wipers necessary. Rotate the end
of the lever downward to the Mist position and release
for a single wiping cycle.
Windshield Washer Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201
NOTE: The mist feature does not activate the washer
pump; therefore, no washer fluid will be sprayed on the
windshield. The wash function must be used in order to
spray the windshield with washer fluid.
Rain Sensing Wipers — If Equipped
This feature senses moisture on the windshield and
automatically activates the wipers for the driver. The
feature is especially useful for road splash or overspray
from the windshield washers of the vehicle ahead. Rotate
the end of the multifunction lever to one of four settings
to activate this feature.
The sensitivity of the system can be adjusted with the
multifunction lever. Wiper delay position 1 is the least
sensitive, and wiper delay position 4 is the most sensitive. Setting 3 should be used for normal rain conditions.
Settings 1 and 2 can be used if the driver desires less
wiper sensitivity. Settings 4 can be used if the driver
desires more sensitivity. Place the wiper switch in the
OFF position when not using the system.
Mist Control
NOTE:
• The Rain Sensing feature will not operate when the
wiper switch is in the low or high-speed position.
3
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• The Rain Sensing feature may not function properly • Transmission In NEUTRAL Position — When the
when ice, or dried salt water is present on the windshield.
ignition is ON, and the transmission is in the NEUTRAL position, the Rain Sensing system will not
• Use of Rain-X威 or products containing wax or silicone
operate until the wiper switch is moved, vehicle speed
may reduce Rain Sensing performance.
is greater than 5 mph (8 km/h), or the shift lever is
• A customer programmable feature in the Electronic
moved out of the NEUTRAL position.
Vehicle Information Center (EVIC) allows the Rain
Sensing feature to be turned off. Refer to “Electronic TILT/TELESCOPING STEERING COLUMN
Vehicle Information Center (EVIC)/Personal Settings This feature allows you to tilt the steering column
(Customer-Programmable Features)” in “Understand- upward or downward. It also allows you to lengthen or
ing Your Instrument Panel” for further information.
shorten the steering column. The tilt/telescoping lever is
The Rain Sensing system has protection features for the located below the steering wheel at the end of the
wiper blades and arms, and will not operate under the steering column.
following conditions:
• Low Ambient Temperature — When the ignition is
first turned ON, the Rain Sensing system will not
operate until the wiper switch is moved, vehicle speed
is greater than 0 mph (0 km/h), or the outside temperature is greater than 32°F (0°C).
To unlock the steering column, push the lever downward
(toward the floor). To tilt the steering column, move the
steering wheel upward or downward as desired. To
lengthen or shorten the steering column, pull the steering
wheel outward or push it inward as desired. To lock the
steering column in position, push the lever upward until
fully engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203
WARNING!
Do not adjust the steering column while driving.
Adjusting the steering column while driving or driving with the steering column unlocked, could cause
the driver to lose control of the vehicle. Be sure the
steering column is locked before driving your vehicle. Failure to follow this warning may result in
serious injury or death.
POWER TILT/TELESCOPING STEERING
COLUMN — IF EQUIPPED
This feature allows you to tilt the steering column
upward or downward. It also allows you to lengthen or
shorten the steering column. The power tilt/telescoping
steering column lever is located below the multifunction
lever on the steering column.
3
Power Tilt/Telescoping Steering
To tilt the steering column, move the lever up or down as
desired. To lengthen or shorten the steering column, pull
the lever toward you or push the lever away from you as
desired.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: For vehicles equipped with Driver Memory
Seat, you can use your Remote Keyless Entry (RKE)
transmitter or the memory switch on the driver’s door
trim panel to return the tilt/telescopic steering column to
pre-programmed positions. Refer to “Driver Memory
Seat” in this section for further information.
WARNING!
Do not adjust the steering column while driving.
Adjusting the steering column while driving or driving with the steering column unlocked, could cause
the driver to lose control of the vehicle. Be sure the
steering column is locked before driving your vehicle. Failure to follow this warning may result in
serious injury or death.
HEATED STEERING WHEEL — IF EQUIPPED
The steering wheel contains a heating element that helps
warm your hands in cold weather. The heated steering
wheel has only one temperature setting. Once the heated
steering wheel has been turned on it will operate for
approximately 58 to 70 minutes before automatically
shutting off. The heated steering wheel can shut off early
or may not turn on when the steering wheel is already
warm.
The heated steering wheel switch is located on the switch
bank below the climate controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205
Press the switch to turn on the heated
steering wheel. The light on the switch
will illuminate to indicate the steering
wheel heater is on. Pressing the switch
a second time will turn off the heated
steering wheel and light indicator.
NOTE: The engine must be running for the heated
steering wheel to operate.
WARNING!
• Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It
may cause burns even at low temperatures, especially if used for long periods.
• Do not place anything on the steering wheel that
insulates against heat, such as a blanket or steering
wheel covers of any type and material. This may
cause the steering wheel heater to overheat.
Vehicles Equipped With Remote Start
On models that are equipped with remote start, the
heated steering wheel can be programmed to come on
during a remote start. Refer to “Remote Starting System
— If Equipped” in “Things to Know Before Starting Your
ELECTRONIC SPEED CONTROL
Vehicle” for further information.
When engaged, the Electronic Speed Control takes over
accelerator operations at speeds greater than 20 mph
(32 km/h).
3
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The Electronic Speed Control buttons are located on the the same time. If this occurs, the Electronic Speed Control
right side of the steering wheel.
System can be reactivated by pushing the Electronic
Speed Control ON/OFF button and resetting the desired
vehicle set speed.
To Activate
Push the ON/OFF button. The Cruise Indicator Light in
the instrument cluster will illuminate. To turn the system
off, push the ON/OFF button a second time. The Cruise
Indicator Light will turn off. The system should be
turned off when not in use.
WARNING!
1 — ON/OFF
4 — CANCEL
2 — RES +
3 — SET -
NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut
down if multiple Speed Control functions are operated at
Leaving the Electronic Speed Control system on
when not in use is dangerous. You could accidentally
set the system or cause it to go faster than you want.
You could lose control and have an accident. Always
leave the system OFF when you are not using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207
To Set A Desired Speed
Turn the Electronic Speed Control ON. When the vehicle
has reached the desired speed, press the SET (-) button
and release. Release the accelerator and the vehicle will
operate at the selected speed.
To Vary The Speed Setting
When the Electronic Speed Control is set, you can increase speed by pushing the RES (+) button. If the button
is continually pressed, the set speed will continue to
increase until the button is released, then the new set
speed will be established.
NOTE: The vehicle should be traveling at a steady speed
and on level ground before pressing the SET button.
Pressing the RES (+) button once will result in a 1 mph
(1.6 km/h) increase in set speed. Each subsequent tap of
To Deactivate
the button results in an increase of 1 mph (1.6 km/h).
A soft tap on the brake pedal, pushing the CANCEL
button, or normal brake pressure while slowing the To decrease speed while the Electronic Speed Control is
vehicle will deactivate Electronic Speed Control without set, push the SET (-) button. If the button is continually
erasing the set speed memory. Pressing the ON/OFF held in the SET (-) position, the set speed will continue to
button or turning the ignition switch OFF erases the set decrease until the button is released. Release the button
speed memory.
when the desired speed is reached, and the new set speed
will be established.
To Resume Speed
To resume a previously set speed, push the RES (+) Pressing the SET (-) button once will result in a 1 mph
button and release. Resume can be used at any speed (1.6 km/h) decrease in set speed. Each subsequent tap of
above 20 mph (32 km/h).
the button results in a decrease of 1 mph (1.6 km/h).
3
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To Accelerate For Passing
Press the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.
Using Electronic Speed Control On Hills
The transmission may downshift on hills to maintain the
vehicle set speed.
WARNING!
Electronic Speed Control can be dangerous where the
system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you
could lose control and have an accident. Do not use
Electronic Speed Control in heavy traffic or on roads
that are winding, icy, snow-covered or slippery.
NOTE: The Electronic Speed Control system maintains
speed up and down hills. A slight speed change on
moderate hills is normal.
ADAPTIVE CRUISE CONTROL (ACC) — IF
On steep hills, a greater speed loss or gain may occur so EQUIPPED
it may be preferable to drive without Electronic Speed Adaptive Cruise Control (ACC) increases the driving
convenience provided by cruise control while traveling
Control.
on highways and major roadways. However, it is not a
safety system and not designed to prevent collisions.
ACC will allow you to keep cruise control engaged in
light to moderate traffic conditions without the constant
need to reset your cruise control. ACC utilizes a radar
sensor designed to detect a vehicle directly ahead of you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209
NOTE:
• If the sensor does not detect a vehicle ahead of you,
ACC will maintain a fixed set speed.
• If the ACC sensor detects a vehicle ahead, ACC will
apply limited braking or acceleration (not to exceed
the original set speed) automatically to maintain a
preset following distance, while matching the speed of
the vehicle ahead.
WARNING!
• Adaptive Cruise Control (ACC) is a convenience
system. It is not a substitute for active driving
involvement. It is always the driver’s responsibility to be attentive of road, traffic, and weather
conditions, vehicle speed, distance to the vehicle
ahead; and, most importantly, brake operation to
ensure safe operation of the vehicle under all road
conditions. Your complete attention is always required while driving to maintain safe control of
your vehicle. Failure to follow these warnings can
result in a collision and death or serious personal
injury.
• The ACC system:
− Does not react to pedestrians, oncoming vehicles,
and stationary objects (e.g., a stopped vehicle in a
traffic jam or a disabled vehicle).
(Continued)
3
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING! (Continued)
WARNING!
− Cannot take street, traffic, and weather conditions
into account, and may be limited upon adverse sight
distance conditions.
− Does not predict the lane curvature or the movement of preceding vehicles and will not compensate
for such changes.
− Does not always fully recognize complex driving
conditions, which can result in wrong or missing
distance warnings.
− Can only apply a maximum of 25% of the vehicle’s
braking capability, and will not bring the vehicle to a
complete stop.
You should switch off the ACC system:
• When driving in fog, heavy rain, heavy snow,
sleet, heavy traffic, and complex driving situations
(i.e., in highway construction zones).
• When entering a turn lane or highway off ramp;
when driving on roads that are winding, icy,
snow-covered, slippery, or have steep uphill or
downhill slopes.
• When towing a trailer up or down steep slopes.
• When circumstances do not allow safe driving at a
constant speed.
Failure to follow these warnings can result in a
collision or serious personal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211
The Cruise Control system has two control modes:
• Adaptive Cruise Control mode for maintaining an
appropriate distance between vehicles.
• Normal (fixed speed) cruise control mode for cruising
at a constant preset speed. For additional information,
refer to “Normal (Fixed Speed) Cruise Control Mode”
in this section.
3
NOTE: The system will not react to preceding vehicles.
Always be aware of the mode selected.
You can change the mode by using the Cruise Control
buttons. The two control modes function differently.
Always confirm which mode is selected.
Adaptive Cruise Control (ACC) Operation
The speed control buttons (located on the right side of the
steering wheel) operates the ACC system.
1
2
3
4
5
6
—
—
—
—
—
—
DISTANCE SETTING
RES +
SET CANCEL
ON/OFF
MODE
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: Any chassis/suspension modifications to the • When the parking brake is set.
vehicle will effect the performance of the Adaptive Cruise
• When the automatic transmission is in PARK, REControl.
VERSE or NEUTRAL.
Activating Adaptive Cruise Control (ACC)
• When pushing the RES + button without a previously
You can only activate ACC if the vehicle speed is above
set speed in memory.
20 mph (32 km/h).
To Activate
When the system is turned on and in the READY state,
Push and release the ON/OFF button. The ACC menu in
the Electronic Vehicle Information Center (EVIC) disthe EVIC displays “Adaptive Cruise Ready.”
plays “Adaptive Cruise Ready.”
When the system is OFF, the EVIC displays “Adaptive
Cruise Control Off.”
NOTE: You cannot enable ACC under the following
conditions:
• When in Four-Wheel Drive Low.
• When you apply the brakes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213
To turn the system OFF, push and release the ON/OFF
button again. At this time, the system will turn off and
the EVIC will display “Adaptive Cruise Control Off.”
WARNING!
Leaving the Adaptive Cruise Control (ACC) system
on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you
want. You could lose control and have a collision.
Always leave the system off when you are not using
it.
Adaptive Cruise Control Ready
3
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Remove your foot from the accelerator pedal. If you do
To Set A Desired ACC Speed
When the vehicle reaches the speed desired, push the not, the vehicle may continue to accelerate beyond the set
SET - button and release. The EVIC will display the set speed. If this occurs:
speed.
• The message “DRIVER OVERRIDE” will display in
the EVIC.
• The system will not be controlling the distance between your vehicle and the vehicle ahead. The vehicle
speed will only be determined by the position of the
accelerator pedal.
ACC Set
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215
To Cancel
The system will disable ACC without erasing the
memory if:
• You softly tap the brake pedal.
• You depress the brake pedal.
• You press the CANCEL switch.
• An Anti-Lock Brake System (ABS) event occurs.
• A Trailer Sway Control (TSC) event occurs.
• If the transmission is shifted into NEUTRAL.
Driver Override
• The Electronic Stability Control/Traction Control System (ESC/TCS) activates.
3
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: If ACC is resumed or set with the ESC/TCS off, • You turn OFF the ignition.
ESC will automatically be re-engaged.
• You switch to Four-Wheel Drive Low.
To Resume Speed
Press the RES + button and release. Then remove your
foot from the accelerator pedal. The EVIC will display the
last set speed.
NOTE: You can resume ACC from a minimum of
20 mph (32 km/h).
WARNING!
Adaptive Cruise Control Cancelled
To Turn Off
The system will turn off and erase the set speed in
memory if:
• You push the ON/OFF button.
The Resume function should only be used if traffic
and road conditions permit. Resuming a set speed
that is too high or too low for prevailing traffic and
road conditions could cause the vehicle to accelerate
or decelerate too sharply for safe operation. Failure to
follow these warnings can result in a collision and
death or serious personal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217
To Vary The Speed Setting
While ACC is set, you can increase the set speed by
pressing and holding the RES + button. If the button is
continually pressed, the set speed will continue to increase in 5 mph (8 km/h) increments until the button is
released. The increase in set speed is reflected in the EVIC
display.
Pressing the SET - button once will result in a 1 mph
(1.6 km/h) decrease in set speed. Each subsequent tap of
the button results in a decrease of 1 mph (1.6 km/h).
NOTE:
• When you use the SET - button to decelerate, if the
engine’s braking power does not slow the vehicle
sufficiently to reach the set speed, the brake system
will automatically slow the vehicle.
Pressing the RES + button once will result in a 1 mph
(1.6 km/h) increase in set speed. Each subsequent tap of
• The ACC system can only apply a maximum of 25% of
the button results in an increase of 1 mph (1.6 km/h).
the vehicle’s braking capability and will not bring the
vehicle to a complete stop.
While ACC is set, the set speed can be decreased by
pressing and holding the SET - button. If the button is
• The ACC system maintains set speed when driving up
continually pressed, the set speed will continue to dehill and down hill. However, a slight speed change on
crease in 5 mph (8 km/h) increments until the button is
moderate hills is normal. In addition, downshifting
released. The decrease in set speed is reflected in the
may occur while climbing uphill or descending downEVIC display.
hill. This is normal operation and necessary to maintain set speed.
3
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Setting The Following Distance In ACC
The specified following distance for ACC can be set by
varying the distance setting between 3 (long), 2 (medium), and 1 (short). Using this distance setting and the
vehicle speed, ACC calculates and sets the distance to the
vehicle ahead. This distance setting displays in the EVIC.
Distance Setting 2
Distance Setting 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219
same lane, the EVIC displays the “Sensed Vehicle Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of
the set speed.
The vehicle will then maintain the set distance until:
• The vehicle ahead accelerates to a speed above the set
speed.
• The vehicle ahead moves out of your lane or view of
the sensor.
• The vehicle ahead slows to a speed below 15 mph
(24 km/h) and the system automatically disengages
To change the distance setting, press the Distance button
itself.
and release. Each time the button is pressed, the distance
• The distance setting is changed.
setting adjusts between long, medium, and short.
• The system disengages. (Refer to the information on
If there is no vehicle ahead, the vehicle will maintain the
ACC Activation).
set speed. If a slower moving vehicle is detected in the
Distance Setting 1
3
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The maximum braking applied by ACC is limited; how- The ACC Systems provides Overtake Aid when passing
ever, the driver can always apply the brakes manually, if on the left hand side only. When driving with ACC
engaged and following a Target vehicle, the system will
necessary.
provide an additional acceleration based on your current
NOTE: The brake lights will illuminate whenever the
speed. The acceleration is triggered by indicating a left
ACC system applies the brakes.
turn signal.
A Proximity Warning will alert the driver if ACC predicts
that its maximum braking level is not sufficient to
maintain the set distance. If this occurs, a visual alert
“BRAKE” will flash in the EVIC and a chime will sound
while ACC continues to apply its maximum braking
capacity. When this occurs, you should immediately
apply the brakes as needed to maintain a safe distance
from the vehicle ahead.
Brake Alert
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221
ACC SET
Adaptive Cruise Control (ACC) Menu
The EVIC displays the current ACC system settings. The
− When ACC is set, the set speed will display.
EVIC is located in the upper part of the instrument
The set speed will continue to display in place of the
cluster between the speedometer and the tachometer. The
information it displays depends on ACC system status.
odometer reading when changing the EVIC display
while ACC is set.
Press the MENU button (located on the steering wheel) repeatedly until one of the following displays in the EVIC:
Menu
Button
Adaptive Cruise Control Off
− When ACC is deactivated, the display will read
“Adaptive Cruise Control Off.”
Adaptive Cruise Control Ready
− When ACC is activated but the vehicle speed setting
has not been selected, the display will read “Adaptive
Cruise Control Ready.”
Example Only
3
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The ACC screen will display once again if any ACC Display Warnings And Maintenance
activity occurs, which may include any of the following:
“Clean Radar Sensor In Front Of Vehicle” Warning
• Set Speed Change
The ACC “Clean Radar Sensor In Front Of Vehicle”
warning will display when conditions temporarily limit
• Distance Setting Change
system performance. This most often occurs at times of
• System Cancel
poor visibility, such as in snow or heavy rain. The ACC
system may also become temporarily blinded due to
• Driver Override
obstructions, such as mud, dirt or ice. In these cases, the
• System Off
EVIC will display “Clean Radar Sensor In Front Of
Vehicle” and the system will deactivate.
• ACC Proximity Warning
The “Clean Radar Sensor In Front Of Vehicle” message
• ACC Unavailable Warning
can sometimes be displayed while driving in highly
The EVIC will return to the last display selected reflective areas (i.e. tunnels with reflective tiles, or ice and
after five seconds of no ACC display activity.
snow). The ACC system will recover after the vehicle has
left these areas. Under rare conditions, when the radar is
not tracking any vehicles or objects in its path this
warning may temporarily occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223
If weather conditions are not a factor, the driver should
examine the sensor. It may require cleaning or removal of
an obstruction. The sensor is located in the center of the
vehicle behind the lower grille.
To keep the ACC System operating properly, it is important to note the following maintenance items:
• Always keep the sensor clean. Carefully wipe the
sensor lens with a soft cloth. Be cautious not to damage
the sensor lens.
Clean Radar Sensor Warning
• Do not remove any screws from the sensor. Doing so
could cause an ACC system malfunction or failure and
require a sensor realignment.
NOTE: If the ACC “Clean Radar Sensor In Front Of
Vehicle” warning is active Normal (Fixed Speed) Cruise • If the sensor is damaged due to a collision, see your
Control is still available. For additional information refer
authorized dealer for service.
to “Normal (Fixed Speed) Cruise Control Mode” in this
section.
3
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• Do not attach or install any accessories near the sensor,
including transparent material or aftermarket grilles.
Doing so could cause an ACC system failure or
malfunction.
ACC Unavailable Warning
If the system turns off, and the EVIC displays “ACC/
FCW Unavailable, Vehicle System Error”, there may be a
temporary malfunction that limits ACC functionality.
Although the vehicle is still drivable under normal
When the condition that deactivated the system is no
conditions, ACC will be temporarily unavailable. If this
longer present, the system will return to the “Adaptive
occurs, try activating ACC again later, following a key
Cruise Control Off” state and will resume function by
cycle. If the problem persists, see your authorized dealer.
simply reactivating it.
Service ACC Warning
NOTE:
If the system turns off, and the EVIC displays “ACC/
• If the “Clean Radar Sensor In Front Of Vehicle”
FCW Unavailable Service Radar Sensor”, it indicates
message occurs frequently (e.g. more than once on
there is an internal system fault. Although the vehicle is
every trip) without any snow, rain, mud, or other
still drivable under normal conditions, have the system
obstruction, have the radar sensor realigned at your
checked by an authorized dealer.
authorized dealer.
• Installing a snow plow, front-end protector, an aftermarket grille or modifying the grille is not recommended. Doing so may block the sensor and inhibit
ACC operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225
Precautions While Driving With ACC
In certain driving situations, ACC may have detection
issues. In these cases, ACC may brake late or unexpectedly. The driver needs to stay alert and may need to
intervene.
Adding A Trailer Hitch
The weight of a trailer/hitch may affect the performance
of ACC. If there is a noticeable change in performance
following the installation of a trailer/hitch, or if the ACC
performance does not return to normal after removing
the trailer/hitch see your authorized dealer.
ACC Unavailable Warning
3
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Offset Driving
ACC may not detect a vehicle in the same lane that is
offset from your direct line of travel. There will not be
sufficient distance to the vehicle ahead. The offset vehicle
may move in and out of the line of travel, which can
cause your vehicle to brake or accelerate unexpectedly.
Turns And Bends
When driving on a curve with ACC engaged, the system
may decrease the vehicle speed and acceleration for
convenience reasons, with no target vehicle detected.
Once the vehicle is out of the curve the system will
resume your original Set Speed. This is a part of normal
ACC system functionality.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227
ACC may occasionally provide braking and/or a driver
alert that you consider unnecessary. This may be the
systems response to signs, guardrails, and other stationary objects in a curve. This may also occur at the base of
steep hills. This is normal operation and your vehicle
does not require service.
Using ACC On Hills
When driving on hills, ACC may not detect a vehicle in
your lane. Depending on the speed, vehicle load, traffic
conditions, and the steepness of the hills, ACC performance may be limited.
3
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Lane Changing
ACC will not detect a vehicle until it is completely in the
lane in which you are traveling. In the illustration shown,
ACC has not yet detected the vehicle changing lanes and
it may not detect the vehicle until it’s too late for the ACC
system to take action. ACC will not detect a vehicle until
it is completely in the lane. There will not be sufficient
distance to the lane-changing vehicle. Always be attentive and ready to apply the brakes if necessary.
Narrow Vehicles
Some narrow vehicles traveling near the outer edges of
the lane or edging into the lane are not detected until they
have moved fully into the lane. There will not be sufficient distance to the vehicle ahead.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229
3
Stationary Objects And Vehicles
General Information
ACC does not react to stationary objects and stationary
FCC Requirements For Vehicular Radar Systems
vehicles. For example, ACC will not react in situations
Classification Specifications:
where the vehicle you are following exits your lane and
47 C.F.R. Part 15
the vehicle ahead is stopped in your lane. Always be
47
C.F.R Part 15.515
attentive and ready to apply the brakes if necessary.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Normal (Fixed Speed) Cruise Control Mode
In addition to Adaptive Cruise Control mode, a normal
(fixed speed) Cruise Control mode is available for cruising at fixed speeds. The normal Cruise Control mode is
designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Cruise Control
can only be operated if the vehicle speed is above 20 mph
(32 km/h).
WARNING!
In the normal Cruise Control mode, the system will
not react to vehicles ahead. In addition, the proximity
warning does not activate and no alarm will sound
even if you are too close to the vehicle ahead since
neither the presence of the vehicle ahead nor the
vehicle-to-vehicle distance is detected. Be sure to
maintain a safe distance between your vehicle and
the vehicle ahead. Always be aware which mode is
selected.
To change between the different cruise modes, press the
MODE button when the system is in either the OFF,
READY or SET state. Pressing of the MODE button in any
state will result in changing to the new Mode in the OFF
To Set A Desired Speed
state.
When the vehicle reaches the speed desired, press the
SET - button and release. The EVIC will display the set
speed.
NOTE: You must observe the display when setting or
changing speed, not the speedometer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231
To Vary The Speed Setting
There are two ways to change the set speed:
To Resume
Press the RES + button and then remove your foot from
the accelerator pedal. The EVIC will display the last set
• Use the accelerator pedal to adjust the vehicle to the
speed.
desired speed and press the SET - button.
To Turn Off
• Tap the RES + or SET - button to increase or decrease
The system will turn off and erase the set speed in
the set speed in 1 mph (1.6 km/h) increments respecmemory if:
tively. Hold the RES + or SET - button for 5 mph
• You push the ON/OFF button.
(8 km/h) increments.
To Cancel
• You turn off the ignition.
The system will disable normal Cruise Control without
• You engage Four-Wheel Drive Low.
erasing the memory if:
If the Cruise Control system is turned off and reactivated,
• You softly tap or depress the brake pedal.
the system will return to the last driver setting (ACC or
• You press the CANCEL button.
Normal Cruise Control).
• The Electronic Stability Control/Traction Control System (ESC/TCS) activates.
3
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Forward Collision Warning — If Equipped
Forward Collision Warning (FCW) warns the driver of a
potential collision with the vehicle in front of you and
prompts the driver to take action in order to avoid the
collision.
When entering or driving in a curve, the FCW alerts may
be triggered on objects other than vehicles such as guard
rails or sign posts based on the course prediction. This is
expected and is a part of normal FCW activation and
functionality.
FCW monitors the information from the forward looking
sensor as well as the Electronic Brake Controller (EBC),
wheel speed sensors, i.e., to calculate a probable rear-end
collision. When the system determines that a rear-end
collision is probable a warning message (both audible
and visual) will be displayed on the EVIC. When the
system determines a collision with the vehicle in front of
you is no longer probable, the warning message will be
deactivated.
FCW Message
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233
NOTE:
Changing FCW Status
• The minimum speed for FCW activation is 10 mph The FCW feature can be set to far, set to near or turned off
(16 km/h).
in the Electronic Vehicle Information Center (EVIC) refer
to “Electronic Vehicle Information Center (EVIC)” in
• When entering or driving in a curve, the FCW alerts
“Understanding Your Instrument Panel” for further inmay be triggered on objects other than vehicles such as
formation. The FCW Status Off, Near or Far will be
guard rails or sign posts based on the course predicdisplayed in the EVIC.
tion. This is expected and is a part of normal FCW
activation and functionality.
FCW settings can only be changed when the vehicle is in
PARK.
WARNING!
Forward Collision Warning (FCW) is not intended to
avoid a collision on its own, nor can FCW detect
every type of potential collision. The driver has the
responsibility to avoid a collision by controlling the
vehicle via braking and steering. Failure to follow
this warning could lead to serious injury or death.
3
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The default status of FCW is the “Far” setting, this allows
the system to warn you of a possible collision with the
vehicle in front of you when you are farther away. This
gives you the most reaction time.
Changing the FCW status to the “Near” setting, allows
the system to warn you of a possible collision with the
vehicle in front of you when you are much closer. This
setting provides less reaction time than the “Far” setting,
which allows for a more dynamic driving experience.
Example Only
Example Only
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235
Changing the FCW status to “Off” prevents the system
from warning you of a possible collision with the vehicle
in front of you.
3
FCW Off Example
Example Only
NOTE: In the “Off” setting FCW OFF will be displayed
in the EVIC.
NOTE:
• The system will retain the last setting selected by the
driver after ignition shut down.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• FCW will not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path
of the car, stationary objects that are far away, oncoming traffic, or leading vehicles with the same or higher
rate of speed.
• FCW will be disabled like ACC below with the unavailable screens.
Service FCW Warning
If the system turns off, and the EVIC displays “ACC
Unavailable Service Radar Sensor”, it indicates there is an
internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked
by an authorized dealer.
FCW Unavailable Warning
If the system turns off, and the EVIC displays “ACC/
FCW Unavailable, Vehicle System Error”, there may be a
temporary malfunction that limits FCW functionality.
Although the vehicle is still drivable under normal
conditions, FCW will be temporarily unavailable. If this
occurs, try activating FCW again later, following a key
cycle. If the problem persists, see your authorized dealer.
ACC Unavailable Warning
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237
PARKSENSE姞 REAR PARK ASSIST — IF
EQUIPPED
The ParkSense威 Rear Park Assist system provides visual
and audible indications of the distance between the rear
fascia and a detected obstacle when backing up, e.g.
during a parking maneuver. Refer to ParkSense威 System
Usage Precautions for limitations of this system and
recommendations.
ParkSense姞 Sensors
The four ParkSense威 sensors, located in the rear fascia/
bumper, monitor the area behind the vehicle that is
within the sensors’ field of view. The sensors can detect
obstacles from approximately 12 in (30 cm) up to 79 in
(200 cm) from the rear fascia/bumper in the horizontal
direction, depending on the location, type and orientation of the obstacle.
ParkSense威 will retain the last system state (enabled or ParkSense姞 Warning Display
disabled) from the last ignition cycle when the ignition is The ParkSense威 Warning screen will only be displayed if
Sound and Display is selected from the Customerchanged to the ON/RUN position.
Programmable Features section of the Electronic Vehicle
ParkSense威 can be active only when the shift lever is in
Information Center (EVIC). Refer to “Electronic Vehicle
REVERSE. If ParkSense威 is enabled at this shift lever
Information Center (EVIC)/Personal Settings (Customerposition, the system will remain active until the vehicle
Programmable Features)” in “Understanding Your Instruspeed is increased to approximately 11 mph (18 km/h) or
ment Panel” for further information.
above. The system will become active again if the vehicle
speed is decreased to speeds less than approximately
10 mph (16 km/h).
3
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The ParkSense威 Warning Display is located in the Instru- ParkSense姞 Display
ment cluster’s EVIC display. It provides both visual and When the vehicle is in REVERSE, the warning display
audible warnings to indicate the distance between the will turn ON indicating the system status.
rear fascia/bumper and the detected obstacle.
Park Assist System ON
ParkSense威 Warning Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239
3
Park Assist System OFF
The system will indicate a detected obstacle by showing
three solid arcs and will produce a one-half second tone.
As the vehicle moves closer to the object the EVIC
display will show fewer arcs and the sound tone will
change from slow, to fast, to continuous.
Slow Tone
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Fast Tone
Continuous Tone
The vehicle is close to the obstacle when the EVIC display
shows one flashing arc and sounds a continuous tone.
The following chart shows the warning alert operation
when the system is detecting an obstacle:
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241
Rear Distance
(in/cm)
Audible Alert
Chime
Display Message
Greater than
79 in (200 cm)
None
Arcs
Park Assist
System ON
None
Radio Mute
No
WARNING ALERTS
79-39 in
39-25 in
(200-100 cm)
(100-65 cm)
Single 1/2
Slow
Second Tone
Warning Object
Warning Object
Detected
Detected
3 Solid
3 Slow
(Continuous)
Flashing
Yes
Yes
NOTE: ParkSense威 will MUTE the radio, if on, when
the system is sounding an audio tone.
Enabling And Disabling ParkSense姞
ParkSense威 can be enabled and disabled with a switch
located in the switch bank of the instrument panel or
through the Customer-Programmable Features section of
the EVIC. The available choices are: OFF, Sound Only, or
25-12 in
(65-30 cm)
Fast
Less than
12 in (30 cm)
Continuous
Warning Object
Detected
2 Slow
Flashing
Yes
Warning Object
Detected
1 Slow
Flashing
Yes
Sound and Display. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information.
When the ParkSense威 switch is pressed to
disable the system, the instrument cluster will
display the “PARK ASSIST SYSTEM OFF” message for approximately five seconds. Refer to
3
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
“Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is moved to REVERSE and the
system is disabled, the EVIC will display the “PARK
ASSIST SYSTEM OFF” message for as long as the vehicle
is in REVERSE.
detected a faulted condition, the EVIC will display the
“CLEAN PARK ASSIST SENSORS” or the “SERVICE
PARK ASSIST SYSTEM” message for as long as the
vehicle is in REVERSE. Under this condition, ParkSense威
will not operate.
If “CLEAN PARK ASSIST SENSORS” appears in the
The ParkSense威 switch LED will be ON when Electronic Vehicle Information Center (EVIC) make sure
ParkSense威 is disabled or defective. The ParkSense威 the rear fascia/bumper is clean and clear of snow, ice,
mud, dirt or other obstruction and then cycle the ignition.
switch LED will be OFF when the system is enabled.
If the message continues to appear see an authorized
Service The ParkSense姞 Rear Park Assist System
dealer.
When the ParkSense威 Rear Park Assist System is malfunctioning, the instrument cluster will actuate a single If “SERVICE PARK ASSIST SYSTEM” appears in the
chime, once per ignition cycle, and it will display the EVIC, see an authorized dealer.
“CLEAN PARK ASSIST SENSORS” or the “SERVICE
Cleaning The ParkSense姞 System
PARK ASSIST SYSTEM” message. Refer to “Electronic
Clean the ParkSense威 sensors with water, car wash soap
Vehicle Information Center (EVIC)” in “Understanding
and a soft cloth. Do not use rough or hard cloths. Do not
Your Instrument Panel” for further information. When
scratch or poke the sensors. Otherwise, you could damthe shift lever is moved to REVERSE and the system has
age the sensors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243
ParkSense姞 System Usage Precautions
• ParkSense威, when on, will MUTE the radio when it is
sounding a tone.
NOTE:
• Ensure that the rear bumper is free of snow, ice, mud, • Clean the ParkSense威 sensors regularly, taking care
dirt and debris to keep the ParkSense威 system operatnot to scratch or damage them. The sensors must not
ing properly.
be covered with ice, snow, slush, mud, dirt or debris.
Failure to do so can result in the system not working
• Jackhammers, large trucks, and other vibrations could
properly. The ParkSense威 system might not detect an
affect the performance of ParkSense威.
obstacle behind the fascia/bumper, or it could provide
• When you turn ParkSense威 off, the instrument cluster
a false indication that an obstacle is behind the fascia/
will display “PARK ASSIST SYSTEM OFF.” Furtherbumper.
more, once you turn ParkSense威 off, it remains off
• Objects such as bicycle carriers, trailer hitches, etc.,
until you turn it on again, even if you cycle the ignition
must not be placed within 12 in (30 cm) from the rear
key.
fascia/bumper while driving the vehicle. Failure to do
• When you move the shift lever to the REVERSE
so can result in the system misinterpreting a close
position and ParkSense威 is turned off, the EVIC will
object as a sensor problem, causing the “SERVICE
display “PARK ASSIST SYSTEM OFF” message for as
PARK ASSIST SYSTEM” message to be displayed in
long as the vehicle is in REVERSE.
the EVIC.
3
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• On vehicles equipped with a tailgate, ParkSense威
should be disabled when the tailgate is in the lowered
or open position and the vehicle is in REVERSE. A
lowered tailgate could provide a false indication that
an obstacle is behind the vehicle.
CAUTION!
• ParkSense威 is only a parking aid and it is unable
to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located
above or below the sensors will not be detected
when they are in close proximity.
• The vehicle must be driven slowly when using
ParkSense威 in order to be able to stop in time
when an obstacle is detected. It is recommended
that the driver looks over his/her shoulder when
using ParkSense威.
WARNING!
• Drivers must be careful when backing up even
when using the ParkSense威 Rear Park Assist System. Always check carefully behind your vehicle,
look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and
blind spots before backing up. You are responsible
for safety and must continue to pay attention to
your surroundings. Failure to do so can result in
serious injury or death.
(Continued)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245
WARNING! (Continued)
• Before using the ParkSense威 Rear Park Assist
System, it is strongly recommended that the ball
mount and hitch ball assembly is disconnected
from the vehicle when the vehicle is not used for
towing. Failure to do so can result in injury or
damage to vehicles or obstacles because the hitch
ball will be much closer to the obstacle than the
rear fascia when the warning display turns on the
single flashing arc and sounds the continuous
tone. Also, the sensors could detect the ball mount
and hitch ball assembly, depending on its size and
shape, giving a false indication that an obstacle is
behind the vehicle.
PARKVIEW姞 REAR BACK UP CAMERA — IF
EQUIPPED
Your vehicle may be equipped with the ParkView威 Rear
Back Up Camera that allows you to see an on-screen
image of the rear surroundings of your vehicle whenever
the shift lever is put into REVERSE. The image will be
displayed on the Navigation/Multimedia radio display
screen along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear. The ParkView威 camera is
located on the rear of the vehicle above the rear License
plate.
When the vehicle is shifted out of REVERSE, the rear
camera mode is exited and the navigation or audio screen
appears again.
3
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
When displayed, static grid lines will illustrate the width that will help indicate the distance to the rear of the
of the vehicle while a dashed center-line will indicate the vehicle. The following table shows the approximate
center of the vehicle to assist with aligning to a hitch/ distances for each zone:
receiver. The static grid lines will show separate zones
Zone
Red
Yellow
Green
Distance to the rear of the vehicle
0 - 1 ft (0 - 30 cm)
1 ft - 3 ft (30 cm - 1 m)
3 ft or greater (1 m or greater)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247
WARNING!
CAUTION! (Continued)
Drivers must be careful when backing up even when
using the ParkView威 Rear Back Up Camera. Always
check carefully behind your vehicle, and be sure to
check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are
responsible for the safety of your surroundings and
must continue to pay attention while backing up.
Failure to do so can result in serious injury or death.
CAUTION!
• To avoid vehicle damage, ParkView威 should only
be used as a parking aid. The ParkView威 camera is
unable to view every obstacle or object in your
drive path.
(Continued)
• To avoid vehicle damage, the vehicle must be
driven slowly when using ParkView威 to be able to
stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/
her shoulder when using ParkView威.
NOTE: If snow, ice, mud, or any foreign substance
builds up on the camera lens, clean the lens, rinse with
water, and dry with a soft cloth. Do not cover the lens.
Turning ParkView姞 On Or Off — With
Navigation/Multimedia Radio
1. Press the “menu” hard-key.
2. Select “system setup” soft-key.
3. Press the “camera setup” soft-key.
3
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
4. Enable or disable the rear camera feature by selecting
the “enable rear camera in reverse” soft-key.
5. Press the “save” soft-key.
Turning ParkView姞 On Or Off — Without
Navigation/Multimedia Radio
1. Press the “menu” hard-key.
2. Select “system setup” soft-key.
3. Enable or disable the rear camera feature by selecting
“enable rear camera in reverse” soft-key and pressing the
“save” soft-key.
Overhead Console
Front Map/Reading Lights
OVERHEAD CONSOLE
The overhead console contains courtesy/reading lights Lights are mounted in the overhead console. Each light
and storage for sunglasses. Universal Garage Door can be turned on by pressing the switch on either side of
Opener (HomeLink威), power liftgate and power sunroof the console. These buttons are backlit for night time
visibility.
switches may also be included, if equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249
Courtesy Lights
The courtesy lights can be turned on by pressing the top
corner of the lens. To turn the lights off, press the lens a
second time.
3
Front Map/Reading Lights
To turn the lights off, press the switch a second time. The
lights also turn on when a door is opened. The lights will
also turn on when the UNLOCK button on the RKE is
pressed.
Courtesy Lights
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Sunglass Bin Door
At the front of the console a compartment is provided for
the storage of a pair of sunglasses. The storage compartment access is a “push/push” design. Push the chrome
pad on the door to open. Push the chrome pad on the
door to close.
GARAGE DOOR OPENER — IF EQUIPPED
HomeLink威 replaces up to three hand-held transmitters
that operate devices such as garage door openers, motorized gates, lighting or home security systems. The
HomeLink威 unit is powered by your vehicles 12 Volt
battery.
The HomeLink威 buttons, located on either the overhead
console, headliner or sunvisor, designate the three different HomeLink威 channels. The HomeLink威 indicator is
located above the center button.
Sunglass Bin Door
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251
3
HomeLink威 Buttons/Overhead Consoles
HomeLink威 Buttons/Sunvisor/Headliner
NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active.
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE:
Before You Begin Programming HomeLink姞
Be sure that your vehicle is parked outside of the garage • Erasing all channels should only be performed when
before you begin programming.
programming HomeLink威 for the first time. Do not
erase channels when programming additional buttons.
For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that • If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
a new battery be placed in the hand-held transmitter of
www.HomeLink.com for information or assistance.
the device that is being programmed to the HomeLink威
system.
Programming A Rolling Code
Erase all channels before you begin programming. To For programming garage door openers that were manuerase the channels place the ignition in the ON/RUN factured after 1995. These garage door openers can be
position and press and hold the two outside HomeLink威 identified by the “LEARN” or “TRAIN” button located
buttons (I and III) for up 20 seconds or until the red where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
indicator flashes.
open and close the door. The name and color of the
button may vary by manufacturer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253
3. Simultaneously press and hold both the Homelink威
button you want to program and the hand-held transmitter button.
4. Continue to hold both buttons and observe the indicator light. The Homelink威 indicator will flash slowly
and then rapidly after Homelink威 has received the frequency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from slow
to rapid.
5. At the garage door opener motor (in the garage),
locate the “LEARN” or “TRAINING” button. This can
Training The Garage Door Opener
usually be found where the hanging antenna wire is
attached to the garage door opener/device motor. Firmly
1 — Door Opener
2 — Training Button
press and release the “LEARN” or “TRAINING” button.
On some garage door openers/devices there may be a
1. Turn the ignition switch to the ON/RUN position.
light that blinks when the garage door opener/device is
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) in the LEARN/TRAIN mode.
away from the HomeLink威 button you wish to program
while keeping the HomeLink威 indicator light in view.
3
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: You have 30 seconds in which to initiate the next 2. Press and hold the desired HomeLink威 button until
the indicator light begins to flash after 20 seconds. Do not
step after the LEARN button has been pressed.
release the button.
6. Return to the vehicle and press the programmed
HomeLink威 button twice (holding the button for two 3. Without releasing the button proceed with “Programseconds each time). If the garage door opener/device ming A Rolling Code” Step 2 and follow all remaining
steps.
activates, programming is complete.
NOTE: If the garage door opener/device does not Programming A Non-Rolling Code
activate, press the button a third time (for two seconds) to For programming Garage Door Openers manufactured
before 1995.
complete the training.
To program the remaining two HomeLink威 buttons, 1. Turn the ignition switch to the ON/RUN position.
repeat each step for each remaining button. DO NOT
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
erase the channels.
away from the HomeLink威 button you wish to program
Reprogramming A Single HomeLink威 Button
while keeping the HomeLink威 indicator light in view.
To reprogram a channel that has been previously trained,
3. Simultaneously press and hold both the Homelink威
follow these steps:
button you want to program and the hand-held transmit1. Turn the ignition switch to the ON/RUN position.
ter button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255
4. Continue to hold both buttons and observe the indicator light. The Homelink威 indicator will flash slowly
and then rapidly after Homelink威 has received the frequency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from slow
to rapid.
Reprogramming A Single HomeLink威 Button
To reprogram a channel that has been previously trained,
follow these steps:
1. Turn the ignition switch to the ON/RUN position.
2. Press and hold the desired HomeLink威 button until
the indicator light begins to flash after 20 seconds. Do not
5. Press and hold the programmed HomeLink威 button
release the button.
and observe the indicator light.
3. Without releasing the button proceed with “Program• If the indicator light stays on constantly, programming A Non-Rolling Code” Step 2 and follow all remainming is complete and the garage door/device
ing steps.
should activate when the HomeLink威 button is
Canadian/Gate Operator Programming
pressed.
For programming transmitters in Canada/United States
• To program the two remaining HomeLink威 buttons,
that require the transmitter signals to “time-out” after
repeat each step for each remaining button. DO
several seconds of transmission.
NOT erase the channels.
Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission – which may not be long enough for HomeLink威
3
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
to pick up the signal during programming. Similar to this 4. Watch for the HomeLink威 indicator to change flash
Canadian law, some U.S. gate operators are designed to rates. When it changes, it is programmed. It may take up
time-out in the same manner.
to 30 seconds or longer in rare cases. The garage door
may open and close while you are programming.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage 5. Press and hold the programmed HomeLink威 button
door or gate motor.
and observe the indicator light.
1. Turn the ignition switch to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
away from the HomeLink威 button you wish to program
while keeping the HomeLink威 indicator light in view.
• If the indicator light stays on constantly, programming is complete and the garage door/device
should activate when the HomeLink威 button is
pressed.
• To program the two remaining HomeLink威 buttons,
3. Continue to press and hold the HomeLink威 button,
repeat each step for each remaining button. DO
while you press and release (“cycle”), your hand-held
NOT erase the channels.
transmitter every two seconds until HomeLink威 has
successfully accepted the frequency signal. The indicator If you unplugged the garage door opener/device for
light will flash slowly and then rapidly when fully programming, plug it back in at this time.
trained.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257
Reprogramming A Single HomeLink威 Button
Security
To reprogram a channel that has been previously trained, It is advised to erase all channels before you sell or turn
follow these steps:
in your vehicle.
1. Turn the ignition switch to the ON/RUN position.
To do this, press and hold the two outside buttons for
20 seconds until the red indicator flashes. Note that all
2. Press and hold the desired HomeLink威 button until
channels will be erased. Individual channels cannot be
the indicator light begins to flash after 20 seconds. Do not
erased.
release the button.
The HomeLink威 Universal Transceiver is disabled when
3. Without releasing the button proceed with
the Vehicle Security Alarm is active.
“Canadian/Gate Operator Programming” Step 2 and
follow all remaining steps.
Using HomeLink姞
To operate, press and release the programmed
HomeLink威 button. Activation will now occur for the
programmed device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may
also be used at any time.
3
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Troubleshooting Tips
If you are having trouble programming HomeLink威, here
are some of the most common solutions:
• Replace the battery in the original hand-held transmitter.
• Press the LEARN button on the Garage Door Opener
to complete the training for a Rolling Code.
• Did you unplug the device for programming and
remember to plug it back in?
If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.
WARNING!
• Your motorized door or gate will open and close
while you are programming the universal transceiver. Do not program the transceiver if people,
pets or other objects are in the path of the door or
gate. Only use this transceiver with a garage door
opener that has a “stop and reverse” feature as
required by Federal safety standards. This includes
most garage door opener models manufactured
after 1982. Do not use a garage door opener without
these safety features. Call toll-free 1–800–355–3515
or, on the Internet at www.HomeLink.com for
safety information or assistance.
• Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage
while programming the transceiver. Exhaust gas
can cause serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259
General Information
POWER SUNROOF — IF EQUIPPED
This device complies with FCC rules Part 15 and Industry The power sunroof switch is located between the sun
Canada RSS-210. Operation is subject to the following visors on the overhead console.
two conditions:
1. This device may not cause harmful interference.
3
2. This device must accept any interference that may be
received including interference that may cause undesired
operation.
NOTE:
• The transmitter has been tested and it complies with
FCC and IC rules. Changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority to operate the
device.
• The term IC before the certification/registration number only signifies that Industry Canada technical
specifications were met.
Power Sunroof Switch
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
• Never leave children in a vehicle with the key in
the ignition switch. Occupants, particularly unattended children, can become entrapped by the
power sunroof while operating the power sunroof
switch. Such entrapment may result in serious
injury or death.
• In a collision, there is a greater risk of being
thrown from a vehicle with an open sunroof. You
could also be seriously injured or killed. Always
fasten your seat belt properly and make sure all
passengers are properly secured too.
• Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or
any object to project through the sunroof opening.
Injury may result.
Opening Sunroof — Express
Press the switch rearward and release it within one-half
second and the sunroof will open automatically from any
position. The sunroof will open fully and stop automatically. This is called “Express Open”. During Express
Open operation, any movement of the sunroof switch
will stop the sunroof.
Opening Sunroof — Manual Mode
To open the sunroof, press and hold the switch rearward
to full open. Any release of the switch will stop the
movement and the sunroof will remain in a partially
opened condition until the switch is pushed and held
rearward again.
Closing Sunroof — Express
Press the switch forward and release it within one-half
second and the sunroof will close automatically from any
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261
position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express
Close operation, any movement of the switch will stop
the sunroof.
NOTE: If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt
will be a Manual Close movement with Pinch Protect
disabled.
Closing Sunroof — Manual Mode
To close the sunroof, press and hold the switch in the
forward position. Any release of the switch will stop the
movement and the sunroof will remain in a partially
closed condition until the switch is pushed and held
forward again.
Venting Sunroof — Express
Press and release the Vent button within one half second
and the sunroof will open to the vent position. This is
called “Express Vent”, and it will occur regardless of
sunroof position. During Express Vent operation, any
movement of the switch will stop the sunroof.
Pinch Protect Feature
This feature will detect an obstruction in the opening of
the sunroof during Express Close operation. If an obstruction is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, press
the switch forward and release to Express Close.
Sunshade Operation
The sunshade can be opened manually. However, the
sunshade will open automatically as the sunroof opens.
NOTE: The sunshade cannot be closed if the sunroof is
open.
3
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Wind Buffeting
Wind buffeting can be described as the perception of
pressure on the ears or a helicopter-type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the sunroof (if equipped) is in certain
open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with
the rear windows open, open the front and rear windows
together to minimize the buffeting. If the buffeting occurs
with the sunroof open, adjust the sunroof opening to
minimize the buffeting or open any window.
Ignition OFF Operation
For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), the power sunroof switch
will remain active for 45 seconds after the ignition switch
is turned to the LOCK position. Opening either front
door will cancel this feature.
For vehicles equipped with the EVIC, the power sunroof
switch will remain active for up to approximately ten
minutes after the ignition switch is turned to the LOCK
position. Opening either front door will cancel this
feature. The time is programmable. Refer to “Electronic
Sunroof Maintenance
Vehicle Information Center (EVIC)/Personal Settings
Use only a non-abrasive cleaner and a soft cloth to clean (Customer-Programmable Features)” in “Understanding
the glass panel.
Your Instrument Panel” for further information.
Sunroof Fully Closed
Press the switch forward and release to ensure that the
sunroof is fully closed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263
ELECTRICAL POWER OUTLETS
• To ensure proper operation a MOPAR威 knob and
Your vehicle is equipped with 12 Volt (13 Amp) power
element must be used.
outlets that can be used to power cellular phones, small
• Do not exceed the maximum power of 160 Watts
electronics and other low powered electrical accessories.
(13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power
The power outlets are labeled with either a “key” or a
rating is exceeded the fuse protecting the system will
“battery” symbol to indicate how the outlet is powered.
need to be replaced.
Power outlets labeled with a “key” are powered when
the ignition switch is in the ON or ACC position, while • Power outlets are designed for accessory plugs only.
Do not insert any other object in the power outlets as
the outlets labeled with a “battery” are connected directly
this will damage the outlet and blow the fuse. Imto the battery and powered at all times.
proper use of the power outlet can cause damage not
NOTE:
covered by your New Vehicle Limited Warranty.
• All accessories connected to the “battery” powered
outlets should be removed or turned off when the
vehicle is not in use to protect the battery against
discharge.
3
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The front power outlet is located inside the storage area
on the center stack of the instrument panel.
Front Center Console Outlet
If your vehicle is equipped with a rear full center console,
there is also a power outlet located in the lower storage
Front Power Outlet
In addition to the front power outlet, there is also a power area of the rear full center console.
outlet located in the lower storage area of the front center
console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265
3
Rear Full Center Console Outlet
The rear cargo power outlet is located in the right rear
cargo area.
Rear Cargo Power Outlet
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: The rear cargo power outlet can be switched to
“battery” powered all the time by switching the power
outlet right rear quarter panel fuse in the fuse panel.
Power Outlet Fuse Locations
Power Outlet Right Rear Quarter Panel Fuse
1 — M7 Fuse 20 A Yellow Power Outlet Right Rear Quarter
Panel
2 — M6 Fuse 20 A Yellow Cigar Lighter Front Console
3 — M36 Fuse 20 A Yellow Power Outlet Console Bin
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267
WARNING!
CAUTION!
To avoid serious injury or death:
• Only devices designed for use in this type of
outlet should be inserted into any 12 Volt outlet.
• Do not touch with wet hands.
• Close the lid when not in use and while driving
the vehicle.
• If this outlet is mishandled, it may cause an
electric shock and failure.
• Many accessories that can be plugged in draw
power from the vehicle’s battery, even when not in
use (i.e., cellular phones, etc.). Eventually, if
plugged in long enough, the vehicle’s battery will
discharge sufficiently to degrade battery life
and/or prevent the engine from starting.
• Accessories that draw higher power (i.e., coolers,
vacuum cleaners, lights, etc.) will degrade the
battery even more quickly. Only use these intermittently and with greater caution.
• After the use of high power draw accessories, or
long periods of the vehicle not being started (with
accessories still plugged in), the vehicle must be
driven a sufficient length of time to allow the
generator to recharge the vehicle’s battery.
3
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
POWER INVERTER — IF EQUIPPED
There is a 115 Volt, 150 Watt inverter outlet located on the
back of the center console to convert DC current to AC
current. This outlet can power cellular phones, electronics and other low power devices requiring power up to
150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will
most power tools.
Power Inverter
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269
The power inverter is designed with built-in overload
protection. If the power rating of 150 Watts is exceeded,
the power inverter will automatically shut down. Once
the electrical device has been removed from the outlet the
inverter should automatically reset. If the power rating
exceeds approximately 170 Watts, the power inverter
may have to be reset manually. To reset the inverter
manually press the power inverter button OFF and ON.
To avoid overloading the circuit, check the power ratings
on electrical devices prior to using the inverter.
The power inverter switch is located
on the switch bank below the Climate
Controls. To turn on the power outlet,
press the switch once. Press the switch
a second time to turn the power outlet
off.
NOTE: When the power inverter switch is pressed,
there will be a delay of approximately one second before
the inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the
inverter is producing AC power.
WARNING!
To avoid serious injury or death:
• Do not use a three-prong adaptor.
• Do not insert any objects into the receptacles.
• Do not touch with wet hands.
• Close the lid when not in use.
• If this outlet is mishandled it may cause an electric
shock and failure.
3
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CUPHOLDERS
Rear Cupholders
Front Seat Cupholders
Rear Center Arm Rest Cupholders — If Equipped
There are two cupholders for the front seat passengers There are two cupholders for the rear seat passengers
located in the center console.
located in the fold-down center armrest.
Front Cupholder Location
Rear Center Arm Rest Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271
The rear full console cupholders are equipped with a
Rear Full Console Cupholders — If Equipped
There are two cupholders for the rear seat passengers light ring that illuminates the cupholders for the rear
located in the front of the rear full console.
passengers. The light ring is controlled by the Dimmer
Control. Refer to “Lights” in “Understanding The Features Of Your Vehicle” for further information.
3
Rear Full Console Cupholders
Light Ring In Rear Full Console Cupholders
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Rear Mini Console Cupholders — If Equipped
STORAGE
There are two cupholders for the rear seat passengers
Glove Compartment
located in the front of the rear mini console.
The glove compartment is located on the right side of the
instrument panel.
Rear Mini Console Cupholders
Glove Compartment
To open the glove compartment, pull outward on the
latch and lower the glove box door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273
Door Storage
Front Center Console
Large storage areas are built into the door panels for easy The front center console contains both an upper and a
access.
lower storage area.
3
Door Panel Storage
Storage Compartment
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To open the upper storage compartment, pull upward on Lift upward on the larger of the latches to access the
the small latch located on the lid.
lower storage compartment.
Storage Compartment Latches
Lower Storage Compartment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275
Rear Full Center Console (If Equipped)
The rear full center console contains both an upper and a
lower storage area.
3
Upper Storage Compartment
Lift upward on the larger of the latches to access the
lower storage compartment.
Storage Compartment
To open the upper storage compartment, pull upward on
the small latch located on the front of the lid.
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: Lower storage compartment light is always on The upper storage compartment may also be lifted forwith ignition in the ON/RUN position.
ward. Push in the release button located on the back of
the lid.
CAUTION!
Remove any items stored in the console cupholders
or devices with cords routing through upper storage
area. Damage may occur to upper console lid and
device cables when upper storage compartment is
lifted forward.
Lower Storage Compartment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277
3
Storage Compartment Rear Push Button
When lifted forward there is access to the lower storage
compartment.
Lower Storage Compartment
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Open storage areas, or cubby bins with removable liners, Rear Mini Center Console (If Equipped)
are located rearward of the cupholders and in the lower An open storage area, or cubby bin with removable liner,
is located in the front of the console.
front of the console.
Console Cubby Bins
Console Cubby Bin
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279
CARGO AREA FEATURES
Rechargeable Flashlight
The rechargeable flashlight is mounted on the left side of
the cargo area. The flashlight snaps out of the bezel when
needed. The flashlight features two bright LED light
bulbs and is powered by rechargeable lithium batteries
that recharge when snapped back into place.
3
Press in on the flashlight to release it.
Press And Release
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To operate the flashlight, press the switch once for high, Cargo Storage
There is a removable storage bin located on the left side
twice for low, and a third time to return to off.
of the rear cargo area.
Additional storage can be found in the load floor. To
access the lower storage, lift the handle and raise the
storage lid.
Retractable Cargo Area Cover — If Equipped
NOTE: The purpose of this cover is for privacy, not to
secure loads. It will not prevent cargo from shifting or
protect passengers from loose cargo.
To cover the cargo area:
Three-Press Switch
1. Grasp the cover at the center handle. Pull it over the
cargo area.
2. Insert the pins on the ends of the cover into the slots in
the pillar trim cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281
3. The liftgate may be opened with the cargo cover in
place.
WARNING!
In a collision, a loose cargo cover in the vehicle could
cause injury. It could fly around in a sudden stop and
strike someone in the vehicle. Do not store the cargo
cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken
from its mounting. Do not store it in the vehicle.
Cargo Tie-Down Hooks
The cargo tie-downs, located on the cargo area floor,
should be used to safely secure loads when the vehicle is
moving.
WARNING!
• To help protect against personal injury, passengers
should not be seated in the rear cargo area. The
rear cargo space is intended for load carrying
purposes only, not for passengers, who should sit
in seats and use seat belts.
• Cargo tie-down hooks are not safe anchors for a
child seat tether strap. In a sudden stop or accident, a hook could pull loose and allow the child
seat to come loose. A child could be badly injured.
Use only the anchors provided for child seat
tethers.
The weight and position of cargo and passengers
can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting
in personal injury, follow these guidelines for
loading your vehicle:
(Continued)
3
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING! (Continued)
REAR WINDOW FEATURES
• Do not carry loads which exceed the load limits
described on the label attached to the left door or
left door center pillar.
• Always place cargo evenly on the cargo floor. Put
heavier objects as low and as far forward as
possible.
• Place as much cargo as possible in front of the rear
axle. Too much weight or improperly placed
weight over or behind the rear axle can cause the
rear of the vehicle to sway.
• Do not pile luggage or cargo higher than the top of
the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or
accident.
Rear Window Wiper/Washer
The rear wiper/washer is controlled by a rotary switch
located on the control lever. The control lever is located
on the left side of the steering column.
Rear Wiper/Washer Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283
Rotate the center portion of the lever upward to the If the rear wiper is operating when the ignition is turned
first detent for intermittent operation and to the OFF, the wiper will automatically return to the “park”
position.
second detent for continuous rear wiper operation.
Rotating the center portion upward once more will
activate the washer pump which will continue to
operate as long as the switch is held. Upon release
of the switch, the wipers will resume the continuous rear
wiper operation. When this rotary control is in the OFF
position, rotating it downward will activate the rear
washer pump which will continue to operate as long as
the switch is held. Once the switch is released it will
return to the OFF position and the wipers will cycle two
times before returning to the parked position.
Rear Window Defroster
The rear window defroster button is located on the
climate control panel. Press this button to turn on
the rear window defroster and the heated outside mirrors
(if equipped). An indicator in the button will illuminate
when the rear window defroster is on. The rear window
defroster automatically turns off after approximately
10 minutes. For an additional five minutes of operation,
press the button a second time.
NOTE: To prevent excessive battery drain, use the rear
NOTE: As a protective measure, the pump will stop if window defroster only when the engine is operating.
the switch is held for more than 20 seconds. Once the
switch is released the pump will resume normal operation.
3
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CAUTION!
Failure to follow these cautions can cause damage to
the heating elements:
• Use care when washing the inside of the rear
window. Do not use abrasive window cleaners on
the interior surface of the window. Use a soft cloth
and a mild washing solution, wiping parallel to
the heating elements. Labels can be peeled off
after soaking with warm water.
• Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the
window.
• Keep all objects a safe distance from the window.
ROOF LUGGAGE RACK — IF EQUIPPED
The crossbars and side rails are designed to carry weight
on vehicles equipped with a luggage rack. The load must
not exceed 150 lbs (68 kg), and should be uniformly
distributed over the luggage rack crossbars.
The crossbars on your vehicle are delivered stowed
within the roof rack side rails. Crossbars should always
be used whenever cargo is placed on the roof rack. Check
the straps frequently to be sure that the load remains
securely attached.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285
Deploying the Crossbars
Starting with one crossbar, completely loosen the thumb
screws at both ends of the crossbar.
3
1 — Side Rail
2 — Crossbar
The roof rack does not increase the total load carrying
Thumb Screw
capacity of the vehicle. Be sure the total load of cargo
inside the vehicle plus that on the external rack does not NOTE: The thumb screws cannot be fully removed.
exceed the maximum vehicle load capacity.
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Remove the crossbar from the stowed position by sliding
the crossbar towards the center of the roof. Repeat with
crossbar on the opposite side.
CAUTION!
Be careful when handling the crossbars to prevent
damage to the vehicle.
Starting with one crossbar, bend down the pivot supports
at each end.
Removing Crossbars
Bending Pivot
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287
Position the crossbars across the roof making sure the Slide the cross bar into to the deploy position by moving
letters on the crossbars align with the matching letters on it towards the matching letter in the side rail. Be sure the
the side rail.
crossbar is fully deployed with the crossbar pushed as far
into the slot as possible. Once the crossbar is in place,
tighten both thumb screws completely.
3
Positioning Crossbars
Installing Crossbars
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Deploy and tighten the second crossbar to complete the Stowing the Crossbars
Starting with one crossbar, completely loosen the thumb
deployment of the crossbars.
screws at both ends. Slide the crossbar away from the
matching letter to remove it from the deployed position.
Repeat with the other crossbar.
CAUTION!
Be careful when handling the crossbars to prevent
damage to the vehicle.
Deployed Crossbars
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289
Starting with the one crossbar, bend up the pivot sup- Then, position the crossbar along the correct side rail.
ports at each end.
Make sure the letters on the crossbar align with the
matching letters on the side rail.
3
Crossbar Pivot
Stowing Crossbars
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Slide the crossbar outward, away from the center of the
roof. The crossbar will nest fully within the side rail.
Tightening Crossbar
Crossbar to Side Rail
Once the driver’s side crossbar is in place, tighten the
thumb screws completely.
Repeat the procedure to stow the second crossbar on the
opposite side.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291
CAUTION!
Stowed Crossbars
NOTE:
• To help control wind noise, stow the crossbars in the
side rails when they are not in use.
• If any metallic object is placed over the satellite radio
antenna (if equipped), you may experience interruption of satellite radio reception.
• To prevent damage to the roof of your vehicle, DO
NOT carry any loads on the roof rack without the
crossbars deployed. The load should be secured
and placed on top of the crossbars, not directly on
the roof. If it is necessary to place the load on the
roof, place a blanket or other protective layer
between the load and the roof surface.
• To avoid damage to the roof rack and vehicle, do
not exceed the maximum roof rack load capacity of
150 lbs (68 kg). Always distribute heavy loads as
evenly as possible and secure the load appropriately.
(Continued)
3
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CAUTION! (Continued)
CAUTION! (Continued)
• Load should always be secured to cross bars first,
with tie down loops used as additional securing
points if needed. Tie loops are intended as supplementary tie down points only. Do not use ratcheting mechanisms with the tie loops. Check the
straps and thumbwheels frequently to be sure that
the load remains securely attached.
• Long loads that extend over the windshield, such
as wood panels or surfboards, or loads with large
frontal area should be secured to both the front
and rear of the vehicle.
• Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the
roof rack. Wind forces, due to natural causes or
nearby truck traffic, can add sudden upward lift to
a load. This is especially true on large flat loads
and may result in damage to the cargo or your
vehicle.
(Continued)
WARNING!
Cargo must be securely tied before driving your
vehicle. Improperly secured loads can fly off the
vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack
cautions when carrying cargo on your roof rack.
UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
䡵 Instrument Panel Features . . . . . . . . . . . . . . . 297
▫ Engine Oil Change Indicator System . . . . . . . 322
䡵 Instrument Cluster
. . . . . . . . . . . . . . . . . . . . 298
▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . 323
䡵 Instrument Cluster Descriptions . . . . . . . . . . . 299
▫ Vehicle Speed . . . . . . . . . . . . . . . . . . . . . . . 325
䡵 Electronic Vehicle Information Center (EVIC) . . 309
▫ Trip Info . . . . . . . . . . . . . . . . . . . . . . . . . . 325
▫ Electronic Vehicle Information Center (EVIC)
Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
▫ Vehicle Info
(Customer Information Features) . . . . . . . . . 326
▫ EVIC White Telltale Lights . . . . . . . . . . . . . . 317
▫ Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
▫ EVIC Amber Telltale Lights . . . . . . . . . . . . . 319
▫ Keyless Enter-N-Go
Display — If Equipped . . . . . . . . . . . . . . . . 326
▫ EVIC Red Telltale Lights . . . . . . . . . . . . . . . 319
▫ Messages # . . . . . . . . . . . . . . . . . . . . . . . . . 327
4
294 UNDERSTANDING YOUR INSTRUMENT PANEL
▫ Turn Menu Off . . . . . . . . . . . . . . . . . . . . . . 327
▫ Compass / Temperature Display . . . . . . . . . 327
▫ Customer-Programmable Features
(System Setup) . . . . . . . . . . . . . . . . . . . . . . 330
▫ System Status . . . . . . . . . . . . . . . . . . . . . . . 338
䡵 Media Center 730N/430/430N (RHR/RER/
RBZ/RHB) CD/DVD/HDD/NAV —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 339
▫ Operating Instructions (Voice Command
System) — If Equipped . . . . . . . . . . . . . . . . 340
▫ Operating Instructions (Uconnect™ Phone)
— If Equipped . . . . . . . . . . . . . . . . . . . . . . 340
䡵 Media Center 130 (Sales Code RES) . . . . . . . . . 340
▫ Operating Instructions — Radio Mode . . . . . 340
▫ Operation Instructions — CD Mode For CD
And MP3 Audio Play . . . . . . . . . . . . . . . . . 343
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 345
▫ Operation Instructions - Auxiliary Mode . . . . 348
䡵 Media Center 130 With Satellite Radio
(Sales Code RES+RSC). . . . . . . . . . . . . . . . . . . 349
▫ Operating Instructions — Radio Mode . . . . . 349
▫ Operation Instructions — CD Mode For CD
And MP3 Audio Play . . . . . . . . . . . . . . . . . 355
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 357
▫ List Button (CD Mode For MP3 Play) . . . . . . 359
▫ Info Button (CD Mode For MP3 Play) . . . . . . 359
▫ Uconnect™ Multimedia (Satellite Radio) —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 360
UNDERSTANDING YOUR INSTRUMENT PANEL 295
▫ Operating Instructions (Uconnect™ Phone)
— If Equipped . . . . . . . . . . . . . . . . . . . . . . 364
䡵 iPod威/USB/MP3 Control — If Equipped . . . . . 364
▫ Connecting The iPod威 Or External USB
Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
▫ Single Video Screen . . . . . . . . . . . . . . . . . . . 373
▫ Play Video Games . . . . . . . . . . . . . . . . . . . . 376
▫ Listen To An Audio Source On Channel 2
While A Video Is Playing On Channel 1 . . . . 379
▫ Using This Feature . . . . . . . . . . . . . . . . . . . 367
▫ Important Notes For Single Video Screen
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
▫ Controlling The iPod威 Or External USB
Device Using Radio Buttons . . . . . . . . . . . . . 367
▫ Play A DVD Using The Touch-Screen
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 367
▫ Remote Control . . . . . . . . . . . . . . . . . . . . . 384
▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 369
▫ Remote Control Storage . . . . . . . . . . . . . . . . 387
▫ Bluetooth Streaming Audio (BTSA) . . . . . . . . 371
▫ Locking The Remote Control . . . . . . . . . . . . 387
䡵 Uconnect™ Multimedia Video Entertainment
System (VES)™ — If Equipped . . . . . . . . . . . . 372
▫ Replacing The Batteries . . . . . . . . . . . . . . . . 388
▫ Getting Started . . . . . . . . . . . . . . . . . . . . . . 372
▫ Headphones Operation . . . . . . . . . . . . . . . . 388
▫ Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
4
296 UNDERSTANDING YOUR INSTRUMENT PANEL
▫ Replacing The Batteries . . . . . . . . . . . . . . . . 390
䡵 Radio Operation And Mobile Phones
▫ Unwired威 Stereo Headphone Lifetime
Limited Warranty . . . . . . . . . . . . . . . . . . . . 390
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 408
. . . . . . . 408
▫ System Information . . . . . . . . . . . . . . . . . . . 392
▫ Dual-Zone Automatic Temperature Control
(ATC) — If Equipped . . . . . . . . . . . . . . . . . 408
䡵 Steering Wheel Audio Controls . . . . . . . . . . . . 406
▫ Rear Climate Control — If Equipped . . . . . . 414
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . 406
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 416
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 407
▫ Operating Tips Chart . . . . . . . . . . . . . . . . . 418
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 407
UNDERSTANDING YOUR INSTRUMENT PANEL 297
INSTRUMENT PANEL FEATURES
4
1
2
3
4
5
— Air Outlet
— Instrument Cluster
— Radio
— Glove Compartment
— Climate Controls
6 — Lower Switch Bank
7 — Hazard Switch
8 — Storage Bin
9 — ESC Off Switch
10 — Ignition Switch
11 — Headlight Switch
12 — Hood Release
13 — Fuel Door Release
14 — Dimmer Control
298 UNDERSTANDING YOUR INSTRUMENT PANEL
INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 299
INSTRUMENT CLUSTER DESCRIPTIONS
1. Tachometer
Indicates the engine speed in revolutions per minute
(RPM x 1000).
As an added safety feature, your vehicle has been
equipped with a Tire Pressure Monitoring System
(TPMS) that illuminates a low tire pressure telltale when
one or more of your tires is significantly under-inflated.
Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as
possible, and inflate them to the proper pressure. Driving
on a significantly under-inflated tire causes the tire to
overheat and can lead to tire failure. Under-inflation also
reduces fuel efficiency and tire tread life, and may affect
the vehicle’s handling and stopping ability.
2. Tire Pressure Monitoring Telltale Light
Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recommended
by the vehicle manufacturer on the vehicle
placard or tire inflation pressure label. (If your vehicle
has tires of a different size than the size indicated on the
Please note that the TPMS is not a substitute for proper
vehicle placard or tire inflation pressure label, you should
tire maintenance, and it is the driver’s responsibility to
determine the proper tire inflation pressure for those
maintain correct tire pressure, even if under-inflation has
tires.)
not reached the level to trigger illumination of the TPMS
low tire pressure telltale.
4
300 UNDERSTANDING YOUR INSTRUMENT PANEL
Your vehicle has also been equipped with a TPMS
CAUTION!
malfunction indicator to indicate when the system is not
operating properly. The TPMS malfunction indicator is The TPMS has been optimized for the original
combined with the low tire pressure telltale. When the equipment tires and wheels. TPMS pressures and
system detects a malfunction, the telltale will flash for warning have been established for the tire size
approximately one minute and then remain continuously equipped on your vehicle. Undesirable system operailluminated. This sequence will continue upon subse- tion or sensor damage may result when using requent vehicle start-ups as long as the malfunction exists. placement equipment that is not of the same size,
When the malfunction indicator is illuminated, the sys- type, and/or style. Aftermarket wheels can cause
tem may not be able to detect or signal low tire pressure sensor damage. Do not use tire sealant from a can or
as intended. TPMS malfunctions may occur for a variety balance beads if your vehicle is equipped with a
of reasons, including the installation of replacement or TPMS, as damage to the sensors may result.
alternate tires or wheels on the vehicle that prevent the
TPMS from functioning properly. Always check the 3. Malfunction Indicator Light (MIL)
TPMS malfunction telltale after replacing one or more
The Malfunction Indicator Light (MIL) is part of
tires or wheels on your vehicle, to ensure that the
an onboard diagnostic system called OBD II that
replacement or alternate tires and wheels allow the TPMS
monitors engine and automatic transmission conto continue to function properly.
trol systems. The light will illuminate when the key is in
the ON/RUN position before engine start. If the bulb
UNDERSTANDING YOUR INSTRUMENT PANEL 301
does not come on when turning the key from OFF to
ON/RUN, have the condition checked promptly.
WARNING!
Certain conditions, such as a loose or missing gas cap,
poor fuel quality, etc., may illuminate the light after
engine start. The vehicle should be serviced if the light
stays on through several of your typical driving cycles. In
most situations, the vehicle will drive normally and will
not require towing.
A malfunctioning catalytic converter, as referenced
above, can reach higher temperatures than in normal
operating conditions. This can cause a fire if you
drive slowly or park over flammable substances such
as dry plants, wood, cardboard, etc. This could result
in death or serious injury to the driver, occupants or
others.
CAUTION!
Prolonged driving with the MIL on could cause
damage to the engine control system. It also could
affect fuel economy and drivability. If the MIL is
flashing, severe catalytic converter damage and
power loss will soon occur. Immediate service is
required.
4. Electronic Stability Control (ESC) Activation/
Malfunction Indicator Light — If Equipped
The “ESC Activation/Malfunction Indicator
Light” in the instrument cluster will come on
when the ignition switch is turned to the
ON/RUN position. It should go out with the
engine running. If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine
running, a malfunction has been detected in the ESC
4
302 UNDERSTANDING YOUR INSTRUMENT PANEL
system. If this light remains on after several ignition 5. Electronic Stability Control (ESC) OFF Indicator
cycles, and the vehicle has been driven several miles Light — If Equipped
This light indicates the Electronic Stability Con(kilometers) at speeds greater than 30 mph (48 km/h), see
trol (ESC) is off.
your authorized dealer as soon as possible to have the
problem diagnosed and corrected.
NOTE:
6. Anti-Lock Brake (ABS) Light
• The “ESC Off Indicator Light” and the “ESC
This light monitors the Anti-Lock Brake System
Activation/Malfunction Indicator Light” come on mo(ABS). The light will turn on when the ignition
mentarily each time the ignition switch is turned to
switch is turned to the ON/RUN position and
ON/RUN.
may stay on for as long as four seconds.
• Each time the ignition is turned to ON/RUN, the ESC
If the ABS light remains on or turns on while driving, it
system will be ON, even if it was turned off previously.
indicates that the Anti-Lock portion of the brake system
• The ESC system will make buzzing or clicking sounds is not functioning and that service is required. However,
when it is active. This is normal; the sounds will stop the conventional brake system will continue to operate
when ESC becomes inactive following the maneuver normally if the BRAKE warning light is not on.
that caused the ESC activation.
If the ABS light is on, the brake system should be serviced
as soon as possible to restore the benefits of Anti-Lock
UNDERSTANDING YOUR INSTRUMENT PANEL 303
brakes. If the ABS light does not turn on when the 10. High Beam Indicator
ignition switch is turned to the ON/RUN position, have
This light indicates that the headlights are on high
beam. Pull the turn signal lever toward the steerthe light inspected by an authorized dealer.
ing wheel to switch the headlights to low beam.
7. Front Fog Light Indicator — If Equipped
This indicator will illuminate when the front fog 11. Electronic Vehicle Information Center (EVIC) Red
Telltale Area
lights are on.
This area will display the EVIC reconfigurable red tell8. Park/Headlight ON Indicator — If Equipped
tales. For further information, refer to “Electronic vehicle
This indicator will illuminate when the park
Information Center (EVIC)”.
lights or headlights are turned on.
12. Electronic Vehicle Information Center (EVIC)
Display/Odometer Display
The odometer display shows the total distance the ve9. Turn Signal Indicator
The arrows will flash with the exterior turn signals hicle has been driven.
when the turn signal lever is operated. A tone will
U.S. Federal regulations require that upon transfer of
chime, and an EVIC message will appear if the turn
vehicle ownership, the seller certify to the purchaser the
signals are left on for more than 1 mile (1.6 km).
correct mileage that the vehicle has been driven. If your
NOTE: If either indicator flashes at a rapid rate, check odometer needs to be repaired or serviced, the repair
technician should leave the odometer reading the same
for a defective outside light bulb.
4
304 UNDERSTANDING YOUR INSTRUMENT PANEL
as it was before the repair or service. If s/he cannot do so,
then the odometer must be set at zero, and a sticker must
be placed in the door jamb stating what the mileage was
before the repair or service. It is a good idea for you to
make a record of the odometer reading before the repair/
service, so that you can be sure that it is properly reset, or
that the door jamb sticker is accurate if the odometer
must be reset at zero.
14. 4 LOW
This light alerts the driver that the vehicle is in
the four-wheel drive LOW mode. The front and
rear driveshafts are mechanically locked together forcing the front and rear wheels to
rotate at the same speed. Low range provides a greater
gear reduction ratio to provide increased torque at the
wheels.
When the appropriate conditions exist, this display For further information on four-wheel drive operation
shows the Electronic Vehicle Information Center (EVIC) and proper use, refer to “Four-Wheel Drive Operation —
messages. Refer to “Electronic Vehicle Information If Equipped” in “Starting And Operating”.
Center”.
15. Hill Descent Indicator — If Equipped
13. Electronic Vehicle Information Center (EVIC) White
The symbol illuminates (is armed) when the
Telltale Area
4WD Lock switch is activated and the transThis area will display the EVIC reconfigurable white
mission range indicator is in LOW or REVERSE
telltales. For further information, refer to “Electronic
position (Off-Road Mode).
vehicle Information Center (EVIC)”.
16. Speedometer
Indicates vehicle speed.
UNDERSTANDING YOUR INSTRUMENT PANEL 305
20. Electronic Vehicle Information Center (EVIC)
17. Fuel Door Reminder
The fuel pump symbol points to the side of the Amber Telltale Area
This area will display the EVIC reconfigurable amber
vehicle where the fuel door is located.
caution telltales. For further information, refer to “Electronic vehicle Information Center (EVIC)”.
18. Fuel Gauge
21. Vehicle Security Light
The pointer shows the level of fuel in the fuel tank when
This light will flash rapidly for approximately
the ignition switch is in the ON/RUN position.
15 seconds when the vehicle theft alarm is
arming. The light will flash at a slower speed
19. Air Bag Warning Light
continuously after the alarm is set. The security
This light will turn on for four to eight seconds
as a bulb check when the ignition switch is first light will also come on for about three seconds when the
turned to the ON/RUN position. If the light is ignition is first turned on.
either not on during starting, stays on, or turns
22. Brake Warning Light
on while driving, have the system inspected at an authoThis light monitors various brake functions,
rized dealer as soon as possible. Refer to “Occupant
including brake fluid level and parking brake
Restraints” in “Things To Know Before Starting Your
application. If the brake light turns on it may
Vehicle” for further information.
4
306 UNDERSTANDING YOUR INSTRUMENT PANEL
indicate that the parking brake is applied, that the brake indicated by the Brake Warning Light, which will turn on
fluid level is low, or that there is a problem with the when the brake fluid level in the master cylinder has
dropped below a specified level.
anti-lock brake system reservoir.
If the light remains on when the parking brake has been
disengaged, and the fluid level is at the full mark on the
master cylinder reservoir, it indicates a possible brake
hydraulic system malfunction or that a problem with the
Brake Booster has been detected by the Anti-Lock Brake
System (ABS) / Electronic Stability Control (ESC) system.
In this case, the light will remain on until the condition
has been corrected. If the problem is related to the brake
booster, the ABS pump will run when applying the brake
and a brake pedal pulsation may be felt during each stop.
The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic
system. A leak in either half of the dual brake system is
The light will remain on until the cause is corrected.
NOTE: The light may flash momentarily during sharp
cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and
the brake fluid level checked.
If brake failure is indicated, immediate repair is necessary.
WARNING!
Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may have failed.
It will take longer to stop the vehicle. You could have
a collision. Have the vehicle checked immediately.
UNDERSTANDING YOUR INSTRUMENT PANEL 307
Vehicles equipped with the Anti-Lock Brake System 23. TOW/HAUL
(ABS), are also equipped with Electronic Brake Force
The TOW HAUL button is located on the
center stack upper switch bank. This light will
Distribution (EBD). In the event of an EBD failure, the
illuminate when TOW HAUL mode is selected
Brake Warning Light will turn on along with the ABS
Light. Immediate repair to the ABS system is required.
24. Seat Belt Reminder Light
Operation of the Brake Warning Light can be checked by
When the ignition switch is first turned to the
turning the ignition switch from the OFF position to the
ON/RUN position, this light will turn on for four
ON/RUN position. The light should illuminate for apto eight seconds as a bulb check. During the bulb
proximately two seconds. The light should then turn off
check, if the driver’s seat belt is unbuckled, a chime will
unless the parking brake is applied or a brake fault is
sound. After the bulb check or when driving, if the driver
detected. If the light does not illuminate, have the light
or front passenger seat belt remains unbuckled, the Seat
inspected by an authorized dealer.
Belt Indicator Light will flash or remain on continuously.
The light also will turn on when the parking brake is Refer to “Occupant Restraints” in “Things To Know
applied with the ignition switch in the ON/RUN posi- Before Starting Your Vehicle” for further information.
tion.
NOTE: This light shows only that the parking brake is
applied. It does not show the degree of brake application.
4
308 UNDERSTANDING YOUR INSTRUMENT PANEL
25. Temperature Gauge
The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that
the engine cooling system is operating satisfactorily.
The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades,
or when towing a trailer. It should not be allowed to
exceed the upper limits of the normal operating range.
CAUTION!
Driving with a hot engine cooling system could
damage your vehicle. If the temperature gauge reads
“H” pull over and stop the vehicle. Idle the vehicle
with the air conditioner turned off until the pointer
drops back into the normal range. If the pointer
remains on the “H” and you hear continuous chimes,
turn the engine off immediately and call an authorized dealership for service.
WARNING!
A hot engine cooling system is dangerous. You or
others could be badly burned by steam or boiling
coolant. You may want to call an authorized dealership for service if your vehicle overheats. If you
decide to look under the hood yourself, see “Maintaining Your Vehicle”. Follow the warnings under the
Cooling System Pressure Cap paragraph.
UNDERSTANDING YOUR INSTRUMENT PANEL 309
The EVIC consists of the following:
ELECTRONIC VEHICLE INFORMATION CENTER
(EVIC)
• System Status
The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the • Vehicle Information Warning Message Displays
instrument cluster.
• Customer-Programmable Features (System Setup)
• Compass Display
• Outside Temperature Display
• Trip Computer Functions
Electronic Vehicle Information Center (EVIC) Display
4
310 UNDERSTANDING YOUR INSTRUMENT PANEL
The system allows the driver to select information by UP Button
pressing the following buttons mounted on the steering
Press and release the UP button to scroll upwheel:
ward through the main menus (Fuel Economy,
ACC (if equipped), Vehicle Speed, Trip Info,
Tire PSI, Vehicle Info, Messages, Units, System
Setup, Turn Menu Off) and sub-menus.
DOWN Button
Press and release the DOWN button to scroll
downward through the main menus and submenus.
EVIC Steering Wheel Buttons
SELECT Button
Press and release the SELECT button for access
to main menus, sub-menus or to select a personal setting in the setup menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 311
messages that consist of approximately 60 possible warnBACK Button
Press the BACK button to scroll back to a ing or information messages. These pop up messages fall
into several categories:
previous menu or sub-menu.
• Five Second Stored Messages
When the appropriate conditions occur, this type of
Electronic Vehicle Information Center (EVIC)
message takes control of the main display area for five
Displays
seconds and then returns to the previous screen. Most of
The EVIC display consists of three sections:
the messages of this type are then stored (as long as the
1. The top line where compass direction, odometer line condition that activated it remains active) and can be
reviewed from the ⬙Messages⬙ main menu item. As long
and outside temperature are displayed.
as there is a stored message, an ⬙i⬙ will be displayed in the
2. The main display area where the menus and pop up
EVIC’s compass/outside temp line. Examples of this
messages are displayed.
message type are ⬙Right Front Turn Signal Lamp Out⬙
3. The reconfigurable telltales section below the odom- and ⬙Low Tire Pressure⬙.
eter line.
• Unstored Messages
The main display area will normally display the main This message type is displayed indefinitely or until the
menu or the screens of a selected feature of the main condition that activated the message is cleared. Examples
menu. The main display area also displays ⬙pop up⬙
4
312 UNDERSTANDING YOUR INSTRUMENT PANEL
of this message type are ⬙Turn Signal On⬙ (if a turn signal When the appropriate conditions exist, the EVIC displays
is left on) and ⬙Lights On⬙ (if driver leaves the vehicle). the following messages:
• Unstored Messages Until RUN
These messages deal primarily with the Remote Start
feature. This message type is displayed until the ignition
is in the RUN state. Examples of this message type are
⬙Remote Start Aborted - Door Ajar⬙ and ⬙Press Brake
Pedal and Push Button to Start⬙.
• Vehicle Not in Park
• Key Left Vehicle
• Key Not Detected
• Press Brake Pedal and Push Button to Start
• Premium TPM System Graphic Display
• Five Second Unstored Messages
When the appropriate conditions occur, this type of • Service TPM System (refer to “Tire Pressure Monitormessage takes control of the main display area for five
ing System” in “Starting And Operating”)
seconds and then returns to the previous screen. Ex• Service Keyless System (refer to Keyless Enter-N-Go,
amples of this message type are ⬙Memory System UnPassive Entry - if equipped)
available - Not in Park⬙ and ⬙Automatic High Beams On⬙.
• Service Park Assist System
The Reconfigurable Telltales section is divided into the
white telltales area on the right, amber telltales in the • Park Assist System Blinded
middle, and red telltales on the left.
• Keyfob Battery Low
UNDERSTANDING YOUR INSTRUMENT PANEL 313
• Left front turn signal lamp out
• Right front turn signal lamp out
• Left rear turn signal lamp out
• Right rear turn signal lamp out
• Service air filter
• Low Tire Pressure
• Perform service
• ESC System Off
• Service blind spot system
• Blind spot detection unavailable
• Blind spot system off
• Blind spot detection unavailable sensor blocked
• Normal Cruise Ready — When Adaptive Cruise Control (ACC) system is turned off and Normal (Fixed
Speed) Cruise Control mode is available. Refer to
“Adaptive Cruise Control (ACC)” in “Understanding
The Features Of Your Vehicle” (if equipped).
• Adaptive Cruise Off — When the Adaptive Cruise
Control (ACC) system is turned off. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The
Features Of Your Vehicle” (if equipped).
• ACC Ready — When the ACC system is activated.
Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped).
• ACC Set — After setting the desired speed in the ACC
system. Refer to “Adaptive Cruise Control (ACC)” in
“Understanding The Features Of Your Vehicle” (if
equipped).
4
314 UNDERSTANDING YOUR INSTRUMENT PANEL
• ACC Cancelled — To disable the ACC system. Refer to • Brake — If the ACC system predicts that its maximum
“Adaptive Cruise Control (ACC)” in “Understanding
braking level is not sufficient to maintain the set
The Features Of Your Vehicle” (if equipped).
distance, this message will flash and a chime will
sound while ACC continues to apply its maximum
• Sensed Vehicle Indicator — The system detects a
braking capacity. When this occurs, you should immeslower moving vehicle in the same lane. Refer to
diately apply the brakes as needed to maintain a safe
“Adaptive Cruise Control (ACC)” in “Understanding
distance from the vehicle ahead. Refer to “Adaptive
The Features Of Your Vehicle” (if equipped).
Cruise Control (ACC)” in “Understanding The Fea• Driver Override — If you apply the accelerator after
tures Of Your Vehicle” (if equipped).
setting the desired speed in the ACC system. Refer to • Clean Radar Sensor in the Front of Vehicle — If the
“Adaptive Cruise Control (ACC)” in “Understanding
ACC system deactivates due to performance limiting
The Features Of Your Vehicle” (if equipped).
conditions. Refer to “Adaptive Cruise Control (ACC)”
in “Understanding The Features Of Your Vehicle” (if
• Distance Set — After changing the desired following
equipped).
distance in the ACC system, this message will display
momentarily. Refer to “Adaptive Cruise Control • ACC/FCW Unavailable Vehicle System Error — If the
(ACC)” in “Understanding The Features Of Your
ACC system turns off due to a temporary malfunction
Vehicle” (if equipped).
that limits functionality. Refer to “Adaptive Cruise
Control (ACC)” in “Understanding The Features Of
Your Vehicle” (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 315
• ACC/FCW Unavailable Service Radar Sensor — If the • Oil temp high Speed may be limited
ACC system turns off due to an internal system fault
• Oil temp high Speed limited
that requires service from an authorized dealer. Refer
to “Adaptive Cruise Control (ACC)” in “Understand- • Turn signal on
ing The Features Of Your Vehicle” (if equipped).
• Park assist on
• Cruise Off When Park Brake is On
• Warning object detected
• ACC Cancelled Below Min. Speed
• Remote start aborted — Door ajar
• Coolant low
• Remote start aborted — Hood ajar
• Oil change due > Dealer Info
• Remote start aborted — L/Gate ajar
• Key in ignition
• Remote start aborted — Fuel low
• Lights on
• Remote start disabled — Start Vehicle to Reset
• Key in Ignition Lights On
• Remote start active — Push Start Button
• Ignition or Accessory On
• Remote start active — Insert Key and Turn to Run
• Ignition or Accessory On Lights On
• Memory 1 profile set
4
316 UNDERSTANDING YOUR INSTRUMENT PANEL
• Memory 2 profile set
• Service All Wheel Drive System
• Memory system unavailable — Not in Park
• All Wheel Drive System in neutral
• Memory system unavailable — Seatbelt buckled
• ECO — Fuel Saver Indicator
• Memory 1 profile recall
• To Tow Vehicle Safely, Read Neutral Shift Procedure in
Owners Manual
• Memory 2 profile recall
• Wrong Key
• Damaged Key
• Key not programmed
• Park Assist Disabled
• Automatic high beams on
• Automatic high beams off
• AWD AUTO
• LOW RANGE
• SERV AWD
• For AWD Low Slow Below 5 MPH or 8 KPH Put Trans
in N Press 4 Low
• For AWD High Slow Below 5 MPH or 8 KPH Put Trans
in N Press 4 Low
UNDERSTANDING YOUR INSTRUMENT PANEL 317
EVIC White Telltale Lights
• Electronic Speed Control SET
This area will show reconfigurable white caution tellThis light will turn on when the electronic
tales. These telltales include:
speed control is SET. For further information,
refer to “Electronic Speed Control” in “Under• Shift Lever Status
standing The Features Of Your Vehicle.”
The shift lever status “P,R,N,D,L,5,4,3,2,1” are displayed
indicating the shift lever position. Telltales “5,4,3,2,1” • Adaptive Cruise Control (ACC) ON
This light will turn on when the ACC is ON.
indicate the Electronic Range Select (ERS) feature has
For further information, refer to “Adaptive
been engaged and the gear selected is displayed. For
Cruise Control (ACC)” in “Understanding The
further information on ERS, refer to “Starting And OperFeatures Of Your Vehicle.”
ating”
• Electronic Speed Control ON
• Adaptive Cruise Control (ACC) SET
This light will turn on when the electronic
This light will turn on when the ACC is SET.
speed control is ON. For further information,
For further information, refer to “Adaptive
refer to “Electronic Speed Control” in “UnderCruise Control (ACC)” in “Understanding The
standing The Features Of Your Vehicle.”
Features Of Your Vehicle.”
4
318 UNDERSTANDING YOUR INSTRUMENT PANEL
• Forward Collision Warning (FCW) OFF
This light warns the driver of a potential collision with the vehicle in front and prompts the
driver to take action in order to avoid the
collision. For further information, refer to
“Adaptive Cruise Control (ACC)” in “Understanding
The Features Of Your Vehicle.”
momentarily until the over temperature condition no
longer exists. Once driving conditions are safe, then pull
over and let vehicle idle. After five minutes, the system
will cool and return to normal operation. Refer to “Power
Steering” in “Starting and Operating” for further information.
NOTE:
• Power Steering System Over Temperature — If
• Even if power steering assistance is no longer operaEquipped
tional, it is still possible to steer the vehicle. Under
If the “POWER STEERING SYSTEM OVER
these conditions there will be a substantial increase in
TEMP” message and a icon are displayed on
steering effort, especially at very low vehicle speeds
the EVIC screen, it indicates that extreme steerand during parking maneuvers.
ing maneuvers may have occurred, which
• If the condition persists, see your authorized dealer for
caused an over temperature condition in the power
service.
steering system. You will lose power steering assistance
UNDERSTANDING YOUR INSTRUMENT PANEL 319
EVIC Amber Telltale Lights
• Windshield Washer Fluid Low Indicator
This area will show reconfigurable amber caution tellThis light will turn on to indicate the windtales. These telltales include:
shield washer fluid is low.
• Low Fuel Light
When the fuel level reaches approximately 3.0 gal
• SERV AWD
(11.0 L) this light will turn on, and remain on until
The SERV AWD light monitors the electric shift AWD
fuel is added.
system. If the SERV AWD light stays on or comes on
• Loose Gascap Indicator
during driving, it means that the AWD system is not
If the vehicle diagnostic system determines functioning properly and that service is required.
that the fuel filler cap is loose, improperly
EVIC Red Telltale Lights
installed, or damaged, a loose gascap indicator
This area will show reconfigurable red telltales. These
will display in the telltale display area. Tighten
telltales include:
the fuel filler cap properly and press the SELECT button
to turn off the message. If the problem continues, the • Door Ajar
message will appear the next time the vehicle is started.
This light will turn on to indicate that one or
more doors may be ajar.
A loose, improperly installed, or damaged fuel filler cap
may also turn on the Malfunction Indicator Light (MIL).
4
320 UNDERSTANDING YOUR INSTRUMENT PANEL
If the charging system light remains on, it means that the
• Liftgate Ajar
This light will turn on to indicate that liftgate vehicle is experiencing a problem with the charging
system. Obtain SERVICE IMMEDIATELY. See an authomay be ajar.
rized dealer.
If jump starting is required, refer to “Jump Starting
• Oil Pressure Warning Light
Procedures” in “What To Do In Emergencies”.
This light indicates low engine oil pressure. If the
light turns on while driving, stop the vehicle and • Electronic Throttle Control (ETC) Light
This light informs you of a problem with the
shut off the engine as soon as possible. A chime will
Electronic Throttle Control (ETC) system. The
sound for four minutes when this light turns on.
light will come on when the ignition is first
Do not operate the vehicle until the cause is corrected.
turned ON and remain on briefly as a bulb
This light does not show how much oil is in the engine.
check. If the light does not come on during starting, have
The engine oil level must be checked under the hood.
the system checked by an authorized dealer.
• Charging System Light
If a problem is detected, the light will come on while the
This light shows the status of the electrical chargengine is running. Cycle the ignition key when the
ing system. If the light stays on or comes on while
vehicle has completely stopped and the shift lever is
driving, turn off some of the vehicle’s non-essential
placed in the PARK position. The light should turn off.
electrical devices or increase engine speed (if at idle).
UNDERSTANDING YOUR INSTRUMENT PANEL 321
If the light remains lit with the engine running, your
vehicle will usually be drivable. However, see an authorized dealer for service as soon as possible. If the light is
flashing when the engine is running, immediate service is
required. You may experience reduced performance, an
elevated/rough idle or engine stall and your vehicle may
require towing.
If the light turns on while driving, safely pull over and
stop the vehicle. If the A/C system is on, turn it off. Also,
shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to
normal, turn the engine off immediately and call for
service. Refer to “If Your Engine Overheats” in “What To
Do In Emergencies” for more information.
• Engine Temperature Warning Light
This light warns of an overheated engine condition. As temperatures rise and the gauge approaches H, this indicator will illuminate and a
single chime will sound after reaching a set threshold.
Further overheating will cause the temperature gauge to
pass H, the indicator will continuously flash and a
continuous chime will occur until the engine is allowed
to cool.
• Transmission Temperature Warning Light
This light indicates that there is excessive transmission fluid temperature that might occur
with severe usage such as trailer towing. It may
also occur when operating the vehicle in a high
torque converter slip condition, such as 4-wheel-drive
operation (e.g., snow plowing, off- road operation). If this
light comes on, stop the vehicle and run the engine at idle
or faster, with the transmission in NEUTRAL until the
light goes off.
4
322 UNDERSTANDING YOUR INSTRUMENT PANEL
CAUTION!
Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause
severe transmission damage or transmission failure.
WARNING!
If the Transmission Temperature Warning Light is
illuminated and you continue operating the vehicle,
in some circumstances you could cause the fluid to
boil over, come in contact with hot engine or exhaust
components and cause a fire.
Engine Oil Change Indicator System
Oil Change Due
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Due” message will
flash in the EVIC display for approximately 10 seconds
after a single chime has sounded, to indicate the next
scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate, dependent
upon your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position or cycle the ignition to the ON/RUN position if
equipped with Keyless Enter-N-Go. To turn off the
message temporarily, press and release the MENU button. To reset the oil change indicator system (after
performing the scheduled maintenance) refer to the following procedure.
UNDERSTANDING YOUR INSTRUMENT PANEL 323
Vehicles Equipped With Keyless Enter-N-Go
Fuel Economy
Press and release the UP/DOWN buttons until one of the
1. Without pressing the brake pedal, cycle the ignition to
following Fuel Economy Functions displays in the EVIC:
the ON/RUN position (Do not start the engine.)
• Average Fuel Economy/Fuel Saver Mode
2. Fully depress the accelerator pedal, slowly, three times
• Distance To Empty
within 10 seconds.
3. Cycle the ignition to the OFF/LOCK position.
Average Fuel Economy / Fuel Saver Mode — If
Equipped
Vehicles Not Equipped With Keyless Enter-N-Go
This feature shows the average fuel economy since the
1. Turn the ignition switch to the ON/RUN position (Do last reset. To reset the average fuel economy display,
press and release the SELECT button once while average
not start the engine.)
fuel economy is highlighted. Once reset, the history
2. Fully depress the accelerator pedal, slowly, three times
information will be erased, and the averaging will conwithin 10 seconds.
tinue from the last fuel average reading before the reset.
3. Turn the ignition switch to the OFF/LOCK position.
The FUEL SAVER MODE message will display above the
NOTE: If the indicator message illuminates when you average fuel economy in the EVIC display. This message
start the vehicle, the oil change indicator system did not will appear whenever the Multi-Displacement System
reset. If necessary, repeat this procedure.
4
324 UNDERSTANDING YOUR INSTRUMENT PANEL
(MDS) (if equipped) allows the engine to operate on four Distance To Empty (DTE)
cylinders, or if you are driving in a fuel efficient manner. Shows the estimated distance that can be traveled with
the fuel remaining in the tank. This estimated distance is
determined by a weighted average of the instantaneous
and average fuel economy, according to the current fuel
tank level. DTE cannot be reset through the SELECT
button.
NOTE: Significant changes in driving style or vehicle
loading will greatly affect the actual drivable distance of
the vehicle, regardless of the DTE displayed value.
When the DTE value is less than 30 miles (48 km)
estimated driving distance, the DTE display will change
to a “LOW FUEL” message. This display will continue
Fuel Saver Mode — On
until the vehicle runs out of fuel. Adding a significant
This feature allows you to monitor when you are driving amount of fuel to the vehicle will turn off the “LOW
in a fuel efficient manner, and it can be used to modify FUEL” message and a new DTE value will display.
driving habits in order to increase fuel economy.
UNDERSTANDING YOUR INSTRUMENT PANEL 325
Press the UP/DOWN buttons to cycle through all the
Vehicle Speed
This feature allows you to monitor your vehicle speed on Trip Computer functions. The Trip Functions mode disthe EVIC display, press and release the SELECT button to plays the following information:
change the units of measure between in MPH or km/h.
Trip A
Trip Info
Shows the total distance traveled for Trip A since the last
This feature allows you to track the total distance trav- reset.
eled since the last reset and the elapsed time of travel.
Trip B
Press and release the UP/DOWN buttons until one of the
Shows the total distance traveled for Trip B since the last
following Trip Functions displays in the EVIC:
reset.
• Trip A
Elapsed Time
• Trip B
Shows the total elapsed time of travel since the last reset
when the ignition switch is in the ACC position. Elapsed
• Elapsed Time
time will increment when the ignition switch is in the ON
or START position.
To Reset The Display
Press and release the SELECT button once to clear the
resettable function being displayed.
4
326 UNDERSTANDING YOUR INSTRUMENT PANEL
Vehicle Info (Customer Information Features)
Press and release the UP or DOWN button until “Vehicle
Info” displays in the EVIC and press the SELECT button.
Press the UP and DOWN button to scroll through the
available information displays, then press SELECT to
display any one of the following choices.
• Coolant Temp
Displays the actual coolant temperature.
• Oil Temperature
Displays the actual oil temperature.
• Oil Pressure
Displays the actual oil pressure.
• Trans Temperature
Displays the actual transmission temperature.
• Engine Hours
Displays the number of hours of engine operation.
Units
Press and release the UP or DOWN button until “Units”
displays in the EVIC and press the SELECT button. The
EVIC, odometer, and navigation system (if equipped) can
be changed between English and Metric units of measure. To make your selection, press and release the
SELECT button the selected setting will be displayed.
Keyless Enter-N-Go Display — If Equipped
When the ENGINE START/STOP button is pressed to
change ignition switch positions, the Keyless Enter-N-Go
icon momentarily appears in the lower right corner of the
EVIC display showing the new ignition switch position.
Refer to “Keyless Enter-N-Go” in “Starting And Operating” for more information.
NOTE: Under certain conditions, the display may be
superseded by another display of higher priority. But
when the ignition switch position is changed, the display
always re-appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 327
Messages #
Select from Main Menu using the UP or DOWN buttons.
This feature shows the number of stored warning messages (in the # place holder). Pressing the SELECT button
will allow you to see what the stored messages are. Press
and release the UP and DOWN buttons if there is more
than one message to step through the remaining stored
messages. Pressing the BACK button takes you back to
the Main Menu.
NOTE: The system will display the last known outside
temperature when starting the vehicle and may need to
be driven several minutes before the updated temperature is displayed. Engine temperature can also affect the
displayed temperature; therefore, temperature readings
are not updated when the vehicle is not moving.
Automatic Compass Calibration
This compass is self-calibrating, which eliminates the
need to manually reset the compass. When the vehicle is
Turn Menu OFF
new, the compass may appear erratic and the EVIC will
Select from Main Menu using the DOWN button. Press- display CAL until the compass is calibrated. You may
ing the SELECT button blanks the menu display. Pressing also calibrate the compass by completing one or more
any one of the four steering wheel buttons brings the 360–degree turns (in an area free from large metal or
menu back.
metallic objects) until the CAL indicator displayed in the
EVIC turns off. The compass will now function normally.
Compass / Temperature Display
The compass readings indicate the direction the vehicle is
facing. The EVIC will display one of eight compass
readings and the outside temperature.
4
328 UNDERSTANDING YOUR INSTRUMENT PANEL
NOTE: A good calibration requires a level surface and
an environment free from large metallic objects such as
buildings, bridges, underground cables, railroad tracks,
etc.
Compass Variance
Compass Variance is the difference between Magnetic
North and Geographic North. To compensate for the
differences the variance should be set for the zone where
the vehicle is driven, per the zone map. Once properly
set, the compass will automatically compensate for the
differences, and provide the most accurate compass
heading. For the most accurate compass performance, the
compass must be set using the following steps.
Compass Variance Map
1. Turn the ignition switch ON.
NOTE: Keep magnetic materials away from the top of
2. Press the UP or DOWN button until the Setup
the instrument panel, such as iPod’s, Mobile Phones,
(Customer-Programmable Features) menu is reached,
Laptops and Radar Detectors. This is where the compass
then press the SELECT button.
module is located, and it can cause interference with the
compass sensor, and it may give false readings.
UNDERSTANDING YOUR INSTRUMENT PANEL 329
3. Press the DOWN button until the “Compass Variance” 1. Turn ON the ignition switch.
message is displayed in the EVIC, then press the SELECT
2. Press the UP or DOWN button until the Setup
button. The last variance zone number displays in the
(Customer-Programmable Features) menu is reached,
EVIC.
then press the SELECT button.
4. Press and release the SELECT button until the proper
3. Press the DOWN button until “Calibrate Compass” is
variance zone is selected, according to the map.
displayed in the EVIC.
5. Press and release the BACK button to exit.
4. Press and release the SELECT button to start the
Manual Compass Calibration
calibration. The “CAL” indicator will be displayed in the
If the compass appears erratic and the CAL indicator EVIC.
does not appear in the EVIC display, you must put the
5. Complete one or more 360–degree turns (in an area
compass into the Calibration Mode manually, as follows:
free from large metal or metallic objects) until the “CAL”
NOTE: For the most accurate compass performance, the indicator turns off. The compass will now function
compass variance must be set before performing the normally.
manual compass calibration. The variance should be set
for the zone where the vehicle is driven, per the zone map.
For further information, refer to “Compass Variance.”
4
330 UNDERSTANDING YOUR INSTRUMENT PANEL
Customer-Programmable Features
(System Setup)
Personal Settings allows you to set and recall features
when the transmission is in PARK. If the transmission is
out of PARK or the vehicle begins moving, a warning
message SETUP NOT AVAILABLE, is followed in three
seconds by, VEHICLE NOT IN PARK.
Italian (Italiano), German (Deutsch), and Dutch (Nederlands). Then, as you continue, the information will display in the selected language.
Nav–Turn By Turn
When this feature is selected, the navigation system
utilizes voice commands, guiding through the drive
route, mile by mile, turn-by-turn until the final destinaPress and release the UP or DOWN button until Setup tion is reached. To make your selection, press and release
the SELECT button until a check-mark appears next to
displays in the EVIC.
the feature showing the system has been activated or the
Use the UP or DOWN button to display one of the
check-mark is removed showing the system has been
following choices.
deactivated.
Select Language
Auto Unlock Doors
When in this display you may select one of five lanWhen this feature is selected, all doors will unlock when
guages for all display nomenclature, including the trip
the vehicle is stopped and the transmission is in the
functions and the navigation system (if equipped). Press
PARK or NEUTRAL position and the driver’s door is
the UP or DOWN button while in this display and scroll
opened. To make your selection, press and release the
through the language choices. Press the SELECT button
SELECT button until a check-mark appears next to the
to select English, Spanish (Español), French (Français),
UNDERSTANDING YOUR INSTRUMENT PANEL 331
feature showing the system has been activated, or the all doors will unlock no matter which passive entry
check-mark is removed showing the system has been equipped door handle is grasped. If Driver Door 1st Press
is programmed, only the driver’s door will unlock when
deactivated.
the driver’s door is grasped. With passive entry, if Driver
Remote Unlock Sequence
Door 1st Press is programmed touching the handle more
When Unlock Driver Door Only On 1st Press is selected,
than once will only result in the driver’s door opening.
only the driver’s door will unlock on the first press of the
You have to touch a passenger passive entry equipped
RKE transmitter UNLOCK button. When Driver Door 1st
door handle to unlock all doors passively when Driver’s
Press is selected, you must press the RKE transmitter
Door Only is programmed in the EVIC.
UNLOCK button twice to unlock the passenger’s doors.
When Unlock All Doors On 1st Press is selected, all of RKE Linked To Memory
the doors will unlock on the first press of the RKE When this feature is selected, you can use your RKE
transmitter UNLOCK button. To make your selection, transmitter to recall one of two pre-programmed memory
scroll up or down until the preferred setting is high- profiles. Each memory profile contains desired position
lighted, then press and release the SELECT button until a settings for the driver seat, side mirror, adjustable pedals
check-mark appears next to the setting, showing that the (if equipped), power tilt and telescopic steering column
(if equipped), and a set of desired radio station presets.
setting has been selected.
When OFF is selected, only the MEMORY switch on the
NOTE: If the vehicle is equipped with passive entry and
driver’s door trim panel will recall memory profiles. To
the EVIC is programmed to Unlock All Doors 1st Press,
make your selection, press and release the SELECT
4
332 UNDERSTANDING YOUR INSTRUMENT PANEL
button a check-mark appears next to the feature showing
the system has been activated or the check-mark is
removed showing the system has been deactivated. Refer
to “Driver Memory Seat” in “Understanding The Features Of Your Vehicle.”
Horn With Remote Lock
When this feature is selected, a short horn sound will
occur when the RKE transmitter LOCK button is pressed.
This feature may be selected with or without the “Flash
Lamps with Lock” feature. To make your selection, press
and release the SELECT button until a check-mark apRemote Start Comfort Sys.
pears next to the feature showing the system has been
When this feature is selected and the remote start is
activated or the check-mark is removed showing the
activated, the heated steering wheel and driver heated
system has been deactivated.
seat features will automatically turn on when temperatures are below 40° F (4.4° C). When temperatures are Horn With Remote Start
above 80° F (26.7° C) the driver vented seat will turn on. When this feature is selected, a short horn sound will
These features will stay on through the duration of occur when the RKE transmitter REMOTE START button
remote start or until the key is turned to RUN. To make is pressed. To make your selection, press and release the
your selection, press and release the SELECT button until SELECT button until a check-mark appears next to the
a check-mark appears next to the feature showing the feature showing the system has been activated or the
system has been activated or the check-mark is removed check-mark is removed showing the system has been
deactivated.
showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 333
Flash Lamps With Lock
When this feature is selected, the front and rear turn
signals will flash when the doors are locked or unlocked
with the RKE transmitter. This feature may be selected
with or without the sound horn on lock feature selected.
To make your selection, press and release the SELECT
button until a check-mark appears next to the feature
showing the system has been activated or the check-mark
is removed showing the system has been deactivated.
Headlamp Off Delay
When this feature is selected, the driver can choose to
have the headlights remain on for 0, 30, 60, or 90 seconds
when exiting the vehicle. To make your selection, scroll
up or down until the preferred setting is highlighted,
then press and release the SELECT button until a checkmark appears next to the setting, showing that the setting
has been selected.
Headlamps With Wipers
(Available with Automatic Headlamps Only)
When this feature is selected, and the headlight switch is
in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on.
The headlights will also turn off when the wipers are
turned off if they were turned on by this feature. To make
your selection, press and release the SELECT button until
a check-mark appears next to the feature showing the
system has been activated or the check-mark is removed
showing the system has been deactivated.
NOTE: Turning the headlights on during the daytime
causes the instrument panel lights to dim. To increase the
brightness, refer to “Lights” in “Understanding The
Features Of Your Vehicle.”
4
334 UNDERSTANDING YOUR INSTRUMENT PANEL
Easy Entry/Exit Seat
(Available with Memory Seat Only)
This feature provides automatic driver seat positioning to
enhance driver mobility when entering and exiting the
vehicle. To make your selection, press and release the
SELECT button until a check-mark appears next to the
feature showing the system has been activated or the
check-mark is removed showing the system has been
deactivated.
NOTE: The seat will return to the memorized seat
location (if Recall Memory with Remote Key Unlock is set
to ON) when the RKE transmitter is used to unlock the
door. Refer to “Driver Memory Seat” in “Understanding
The Features Of Your Vehicle” for further information.
Tilt Mirror In Reverse
When this feature is selected, the outside rearview mirrors will tilt downward when the ignition switch is in the
RUN position and the transmission shift lever is in the
REVERSE position. The mirrors will move back to their
previous position when the transmission is shifted out of
REVERSE. To make your selection, press and release the
SELECT button until a check-mark appears next to the
feature showing the system has been activated or the
check-mark is removed showing the system has been
deactivated.
Key-Off Power Delay
When this feature is selected, the power window
switches, radio, hands-free system (if equipped), DVD
video system (if equipped), power sunroof (if equipped),
and power outlets will remain active for up to 10 minutes
after the ignition switch is turned OFF. Opening either
front vehicle door will cancel this feature. To make your
selection, scroll up or down until the preferred setting is
highlighted, then press and release the SELECT button
until a check-mark appears next to the setting, showing
that the setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 335
Illuminated Approach
When this feature is selected, the headlights will activate
and remain on for 0, 30, 60, or 90 seconds when the doors
are unlocked with the RKE transmitter. To make your
selection, scroll up or down until the preferred setting is
highlighted, then press and release the SELECT button
until a check-mark appears next to the setting, showing
that the setting has been selected.
Hill Start Assist (HSA)
When this feature is selected, the HSA system is active.
Refer to “Electronic Brake Control System” in “Starting
And Operating” for system function and operating information. To make your selection, press and release the
SELECT button until a check-mark appears next to the
feature showing the system has been activated or the
check-mark is removed showing the system has been
deactivated.
Display ECO Symbol — If Equipped
The “ECO” message is located in the Compass/
Temperature display; this message can be turned on or
off. To make your selection, press and release the SELECT
button until a check-mark appears next to the setting,
showing that the setting has been selected.
Keyless Enter-N-Go (Passive Entry)
This feature allows you to lock and unlock the vehicle’s
door(s) without having to press the RKE transmitter lock
or unlock buttons. To make your selection, press and
release the SELECT button until a check-mark appears
next to the feature showing the system has been activated
or the check-mark is removed showing the system has
been deactivated. Refer to “Keyless Enter-N-Go ” in
“Things To Know Before Starting Your Vehicle”.
4
336 UNDERSTANDING YOUR INSTRUMENT PANEL
Gauge Glow Rings
The gauge glow rings that illuminate the tachometer and
speedometer in the instrument cluster can be turned on
or off. To make your selection, press and release the
SELECT button until a check-mark appears next to the
feature showing the system has been activated or the
check-mark is removed showing the system has been
deactivated.
Auto High Beams (Available With SmartBeam™
Only)
When this feature is selected, the high beam headlights
will deactivate automatically under certain conditions. To
make your selection, press and release the SELECT
button until a check-mark appears next to the feature
showing the system has been activated or the check-mark
is removed showing the system has been deactivated.
Refer to “Lights/SmartBeam™ — If Equipped” in “Understanding The Features Of Your Vehicle” for further
information.
Intermittent Wiper — If Equipped
When this feature is selected, the system will automatically activate the windshield wipers if it senses moisture
on the windshield. To make your selection, press and
release the SELECT button until a check-mark appears
next to the feature showing the system has been activated
or the check-mark is removed showing the system has
been deactivated. When this feature is deactivated, the
system reverts to the standard intermittent wiper
operation.
Blind Spot Alert
There are three selections when operating Blind Spot
Alert. By pressing and releasing the SELECT button once,
the Blind Spot Alert feature can be activated in “Blind
Spot: Lights Only” mode. When this mode is selected the
Blind Spot Monitor (BSM) system is activated and will
only show a visual alert in the outside mirrors. By
pressing and releasing the SELECT button a second time
“Blind Spot: Lights/CHM” mode is activated. In this
UNDERSTANDING YOUR INSTRUMENT PANEL 337
of a possible collision with the vehicle in front of you
when you are much closer. This allows for a more
dynamic driving experience. To change FCW status press
and release the SELECT button until a check-mark appears next to the feature showing the system has been
activated or the check-mark is removed showing the
NOTE: If your vehicle has experienced any damage in system has been deactivated.
the area where the sensor is located, even if the fascia is
not damaged, the sensor may have become misaligned. For further information, refer to ”Adaptive Cruise ConTake your vehicle to an authorized dealer to verify sensor trol (ACC)” in “Understanding The Features Of Your
alignment. Having a sensor that is misaligned will result Vehicle.”
in the BSM not operating to specification.
Park Assist System
mode the Blind Spot Monitor (BSM) will show a visual
alert in the outside mirrors as well as an audible alert
when the turn signal is on. When “Blind Spot: Off” is
selected the Blind Spot Monitor (BSM) system is deactivated.
Forward Collision Warning
The Forward Collision Warning (FCW) feature can be can
be set to Far, set to Near or turned Off. The default status
of FCW is the Far setting. This means the system will
warn you of a possible collision with the vehicle in front
of you when you are farther away. This gives you the
most reaction time. To change the setting for more
dynamic driving select the Near setting. This warns you
The Rear Park Assist system will scan for objects behind
the vehicle when the transmission is in the REVERSE
position and the vehicle speed is less than 11 mph
(18 km/h). The system can be enabled with Sound Only,
Sound and Display, or turned OFF through the EVIC.
To make your selection, scroll up or down until the
preferred setting is highlighted, then press and release
4
338 UNDERSTANDING YOUR INSTRUMENT PANEL
the SELECT button until a check-mark appears next to
the setting, showing that the setting has been selected.
Refer to “Rear Park Assist System” in “Understanding
The Features Of Your Vehicle” for system function and
operating information.
Calibrate Compass
Refer to “Compass Display” for more information.
Display Units Of Measure In:
The EVIC, odometer, and Uconnect™ gps (if equipped)
can be changed between English and Metric units of
measure. To make your selection, press and release the
SELECT button until “ENGLISH” or “METRIC” appears.
System Status
Compass Variance
Refer to “Compass Display” for more information.
Press and release the UP/DOWN buttons until one of the
following System Status messages displays in the EVIC:
• System OK
• System Warnings Displayed (will display all currently
Liftgate Chime
active System Warnings)
When this feature is selected the chime will sound when
the liftgate is in operation, signaling that the liftgate is in • Tire Pressure Monitor System (shows the current presoperation. To make your selection, press and release the
sure of all four road tires). For additional information,
SELECT button until a check-mark appears next to the
refer to “Tire Pressure Monitor System” in “Starting
feature showing the system has been activated or the
And Operating”.
check-mark is removed showing the system has been
deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 339
Refer to “Tires-General Information/Tire Inflation
Pressures” in “Starting And Operating” for additional
information.
• Your system can be set to display pressure units in PSI,
kPa, or BAR.
MEDIA CENTER 730N/430/430N (RHR/RER/RBZ/
RHB) CD/DVD/HDD/NAV — IF EQUIPPED
NOTE: The sales code is located on the lower right side
of the unit’s faceplate.
Tire Pressure Display
NOTE:
• Tires heat up during normal driving conditions. Heat
will cause the tire pressure to increase from 2 to 6 psi
(14 to 41 kPa) during normal driving conditions.
Refer to your Uconnect™ Multimedia RHR, RER, RBZ or
RHB user’s manual for detailed operating instructions.
4
340 UNDERSTANDING YOUR INSTRUMENT PANEL
Operating Instructions (Voice Command System)
— If Equipped
Refer to “Voice Command” in the Uconnect™ User
Manual located on the DVD for further details.
Operating Instructions (Uconnect™ Phone) — If
Equipped
Refer to “Uconnect™ Phone” in the Uconnect™ User
Manual located on the DVD for further details.
MEDIA CENTER 130 (SALES CODE RES)
NOTE: The radio sales code is located on the lower right
side of the radio faceplate.
Media Center 130 (RES)
Operating Instructions — Radio Mode
NOTE: The ignition switch must be in the ON or ACC
position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 341
Power Switch/Volume Control (Rotary)
TIME Button
Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time
radio. Push the ON/VOLUME control knob a second and radio frequency.
time to turn off the radio.
Clock Setting Procedure
Electronic Volume Control
1. Press and hold the TIME button until the hours blink.
The electronic volume control turns continuously (360
degrees) in either direction, without stopping. Turning 2. Adjust the hours by turning the right side TUNE/
the ON/VOLUME control knob to the right increases the SCROLL control knob.
volume, and to the left decreases it.
3. After adjusting the hours, press the right side TUNE/
When the audio system is turned on, the sound will be SCROLL control knob to set the minutes. The minutes
set at the same volume level as last played.
will begin to blink.
SEEK Buttons
Press and release the SEEK buttons to search for the next
listenable station in AM/FM mode. Press the right switch
to seek up and the left switch to seek down. The radio
will remain tuned to the new station until you make
another selection. Holding either button will bypass
stations without stopping, until you release it.
4. Adjust the minutes using the right side TUNE/
SCROLL control knob. Press the TUNE/SCROLL control
knob to save time change.
5. To exit, press any button/knob, or wait five seconds.
4
342 UNDERSTANDING YOUR INSTRUMENT PANEL
RW/FF
Pressing the RW (Rewind) or FF (Fast Forward) buttons
causes the tuner to search for the next frequency in the
direction of the arrows. This feature operates in either
AM or FM frequencies.
Push the rotary TUNE/SCROLL control knob a third
time and TREBLE will display. Turn the TUNE/SCROLL
control knob to the right or left to increase or decrease the
treble tones.
Setting the Tone, Balance, and Fade
Push the rotary TUNE/SCROLL control knob and BASS
will display. Turn the TUNE/SCROLL control knob to
the right or left to increase or decrease the bass tones.
Push the rotary TUNE/SCROLL control knob a fifth time
and FADE will display. Turn the TUNE/SCROLL control
knob to the left or right to adjust the sound level between
the front and rear speakers.
Push the rotary TUNE/SCROLL control knob a fourth
time and BALANCE will display. Turn the TUNE/
TUNE Control
Turn the rotary TUNE/SCROLL control knob clockwise SCROLL control knob to the right or left to adjust the
to increase or counterclockwise to decrease the frequency. sound level from the right or left side speakers.
Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to
time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade.
control knob to the right or left to increase or decrease the
AM/FM Button
mid-range tones.
Press the buttons to select either AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 343
SET/RND Button — To Set the Pushbutton
Memory
When you are receiving a station that you wish to
commit to pushbutton memory, press the SET/RND
button. The symbol SET 1 will now show in the display
window. Select the button (1 to 6) you wish to lock onto
this station and press and release that button. If a button
is not selected within five seconds after pressing the
SET/RND button, the station will continue to play but
will not be stored into pushbutton memory.
You may add a second station to each pushbutton by
repeating the above procedure with this exception: Press
the SET/RND button twice and SET 2 will show in the
display window. Each button can be set for SET 1 and
SET 2 in both AM and FM. This allows a total of 12 AM
and 12 FM stations to be stored into pushbutton memory.
The stations stored in SET 2 memory can be selected by
pressing the pushbutton twice.
Every time a preset button is used, a corresponding
button number will display.
Buttons 1 - 6
These buttons tune the radio to the stations that you
commit to pushbutton memory (12 AM and 12 FM
stations).
DISC Button
Pressing the DISC button will allow you to switch from
AM/FM modes to Disc modes.
Operation Instructions — CD MODE For CD And
MP3 Audio Play
NOTE:
• The ignition switch must be in the ON or ACC
position to operate the radio.
4
344 UNDERSTANDING YOUR INSTRUMENT PANEL
• This radio is capable of playing compact discs (CD),
recordable compact discs (CD-R), rewritable compact
discs (CD-RW), compact discs with MP3 tracks and
multisession compact discs with CD and MP3 tracks.
Inserting Compact Disc(s)
Gently insert one CD into the CD player with the CD
label facing up. The CD will automatically be pulled into
the CD player and the CD icon will illuminate on the
radio display. If a CD does not go into the slot more than
1.0 in (2.5 cm), a disc may already be loaded and must be
ejected before a new disc can be loaded.
CAUTION!
• This CD player will accept 4-3/4 in (12 cm) discs
only. The use of other sized discs may damage the
CD player mechanism.
• Do not use adhesive labels. These labels can peel
away and jam the player mechanism.
• The RES Media Center is a single CD player. Do
not attempt to insert a second CD if one is already
loaded.
EJECT Button - Ejecting a CD
If you insert a disc with the ignition ON and the radio
Press the EJECT button to eject the CD.
ON, the unit will switch from radio to CD mode and
begin to play when you insert the disc. The display will
show the track number, and index time in minutes and If you have ejected a disc and have not removed it within
10 seconds, it will be reloaded. If the CD is not removed,
seconds. Play will begin at the start of track 1.
the radio will reinsert the CD but will not play it.
A disc can be ejected with the radio and ignition OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL 345
NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button
Press the button to select either AM or FM mode.
convertible or soft-top models (if equipped).
SEEK Button
Press the right SEEK button for the next selection on the
CD. Press the left SEEK button to return to the beginning
of the current selection, or return to the beginning of the
previous selection if the CD is within the first second of
the current selection. Pressing and holding the SEEK
button will allow faster scrolling through the tracks in
CD and MP3 modes.
SET/RND Button (Random Play Button)
Press this button while the CD is playing to activate
Random Play. This feature plays the selections on the
compact disc in random order to provide an interesting
change of pace.
Press the right SEEK button to move to the next randomly selected track.
Press the RND button a second time to stop Random
TIME Button
Play.
Press this button to change the display from a large CD
playing time display to a small CD playing time display. Notes on Playing MP3 Files
The radio can play MP3 files; however, acceptable MP3
RW/FF
file recording media and formats are limited. When
Press and hold the FF (Fast Forward) button and the CD
writing MP3 files, pay attention to the following restricplayer will begin to fast forward until FF is released, or
tions.
RW or another CD button is pressed. The RW (Reverse)
button works in a similar manner.
4
346 UNDERSTANDING YOUR INSTRUMENT PANEL
Supported Media (Disc Types)
The MP3 file recording media supported by the radio are
CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
a number instead. With a maximum number of files,
exceeding 20 folders will result in this display. With
200 files, exceeding 50 folders will result in this
display.)
Supported Medium Formats (File Systems)
The medium formats supported by the radio are ISO 9660 • Maximum number of characters in file/folder names:
Level 1 and Level 2 and includes the Joliet extension.
• Level 1: 12 (including a separator ⬙.⬙ and a threeWhen reading discs recorded using formats other than
character extension)
ISO 9660 Level 1 and Level 2, the radio may fail to read
• Level 2: 31 (including a separator ⬙.⬙ and a threefiles properly and may be unable to play the file norcharacter extension)
mally. UDF and Apple HFS formats are not supported.
Multisession disc formats are supported by the radio.
Multisession discs may contain combinations of normal
• Maximum number of folder levels: 8
CD audio tracks and computer files (including MP3 files).
• Maximum number of files: 255
Discs created with an option such as ⬙keep disc open after
writing⬙ are most likely multisession discs. The use of
• Maximum number of folders. (The radio display of file
multisession for CD audio or MP3 playback may result in
names and folder names is limited. For large numbers
longer disc loading times.
of files and/or folders, the radio may be unable to
display the file name and folder name, and will assign
The radio uses the following limits for file systems:
UNDERSTANDING YOUR INSTRUMENT PANEL 347
Supported MP3 File Formats
The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3
extension may cause playback problems. The radio is
designed to recognize the file as an invalid MP3 and will
not play the file.
MPEG
Specification
MPEG-1 Audio
Layer 3
Sampling Frequency (kHz)
48, 44.1, 32
Bit Rate (kbps)
320, 256, 224,
192, 160, 128,
112, 96, 80, 64,
56, 48, 40, 32
160, 128, 144,
112, 96, 80, 64,
56, 48, 40, 32, 24,
16, 8
When using the MP3 encoder to compress audio data to
MPEG-2 Audio
an MP3 file, the bit rate and sampling frequencies in the
24, 22.05, 16
Layer 3
following table are supported. In addition, variable bit
rates (VBR) are also supported. The majority of MP3 files
use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or ID3 Tag information for artist, song title, and album title
are supported for version 1 ID3 tags. ID3 version 2 is not
VBR bit rate.
supported by the radios.
Playlist files are not supported. MP3 Pro files are not
supported.
4
348 UNDERSTANDING YOUR INSTRUMENT PANEL
Playback of MP3 Files
When a medium containing MP3 data is loaded, the
radio checks all files on the medium. If the medium
contains a lot of folders or files, the radio will take more
time to start playing the MP3 files.
Operation Instructions - Auxiliary Mode
The auxiliary (AUX) jack is an audio input jack, which
allows the user to plug in a portable device, such as an
MP3 player, or cassette player, and utilize the vehicle’s
audio system to amplify the source and play through the
vehicle speakers.
Loading times for playback of MP3 files may be affected
by the following:
Pressing the DISC/AUX button will change the mode to
auxiliary device if the AUX jack is connected.
• Media - CD-RW media may take longer to load than
CD-R media
NOTE: The AUX device must be turned on and the
device’s volume set to proper level. If the AUX audio is
• Medium formats - Multisession discs may take longer
not loud enough, turn the device’s volume up. If the AUX
to load than non-multisession discs
audio sounds distorted, turn the device’s volume down.
• Number of files and folders - Loading times will
TIME Button (Auxiliary Mode)
increase with more files and folders
Press this button to change the display to time of day. The
To increase the speed of disc loading, it is recommended time of day will display for five seconds (when ignition is
to use CD-R media and single-session discs. To create a OFF).
single-session disc, enable the “Disc at Once” option
before writing to the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 349
MEDIA CENTER 130 WITH SATELLITE RADIO
(SALES CODE RES+RSC)
Operating Instructions — Radio Mode
NOTE: The ignition switch must be in the ON/RUN or
NOTE: The radio sales code is located on the lower right ACC position to operate the radio.
side of the radio faceplate.
Power Switch/Volume Control (Rotary)
Push the ON/VOLUME control knob to turn on the
radio. Push the ON/VOLUME control knob a second
time to turn off the radio.
Electronic Volume Control
The electronic volume control turns continuously (360
degrees) in either direction without stopping. Turning the
ON/VOLUME control knob to the right increases the
volume and to the left decreases it.
When the audio system is turned on, the sound will be
set at the same volume level as last played.
Media Center 130 (RES/RSC)
SEEK Buttons
Press and release the SEEK buttons to search for the next
listenable station in AM/FM mode. Press the right switch
4
350 UNDERSTANDING YOUR INSTRUMENT PANEL
to seek up and the left switch to seek down. The radio
will remain tuned to the new station until you make
another selection. Holding either button will bypass
stations without stopping until you release it.
Phone Button Uconnect™ Phone — If Equipped
Press this button to operate the Uconnect™ Phone feature
(if equipped). Refer to “Uconnect™ Phone” in the
Uconnect™ User Manual located on the DVD for further
details.
Voice Command System (Radio) — If Equipped
Refer to “Voice Command” in the Uconnect™ User If your vehicle is not equipped with or this feature is not
Manual located on the DVD for further details.
available on your vehicle, a “Not Equipped With
Uconnect Phone” message will display on the radio
Voice Command Button Uconnect™ Phone — If
screen.
Equipped
Press this button to operate the Uconnect™ Phone feature TIME Button
(if equipped). Refer to “Voice Command” in the Press the TIME button to alternate display of the time
Uconnect™ User Manual located on the DVD for further and radio frequency.
details.
Clock Setting Procedure
If your vehicle is not equipped with or this feature is not
1. Press and hold the TIME button until the hours blink.
available on your vehicle, a “Not Equipped With
Uconnect Phone” message will display on the radio 2. Adjust the hours by turning the right side TUNE/
SCROLL control knob.
screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 351
3. After adjusting the hours, press the right side TUNE/ INFO Button
SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call
letters displayed). The radio will return a Radio Text
will begin to blink.
message broadcast from an FM station (FM mode only).
4. Adjust the minutes using the right side TUNE/
SCROLL control knob. Press the TUNE/SCROLL control RW/FF
Pressing the RW (Rewind) or FF (Fast Forward) buttons
knob to save time change.
causes the tuner to search for the next frequency in the
5. To exit, press any button/knob or wait five seconds.
direction of the arrows. This feature operates in either
The clock can also be set by pressing the SETUP button. AM or FM frequencies.
For vehicles equipped with satellite radio, press the
TUNE Control
SETUP button, use the TUNE/SCROLL control to select
Turn the rotary TUNE/SCROLL control knob clockwise
SET CLOCK, and then follow the above procedure,
to increase or counterclockwise to decrease the frequency.
starting at Step 2. For vehicles not equipped with satellite
radio, press the SETUP button and then follow the above Setting the Tone, Balance, and Fade
Push the rotary TUNE/SCROLL control knob and BASS
procedure, starting at Step 2.
will display. Turn the TUNE/SCROLL control knob to
the right or left to increase or decrease the bass tones.
4
352 UNDERSTANDING YOUR INSTRUMENT PANEL
Push the rotary TUNE/SCROLL control knob a second
time and MID will display. Turn the TUNE/SCROLL
control knob to the right or left to increase or decrease the
mid-range tones.
MUSIC TYPE Button
Pressing this button once will turn on the Music Type
mode for five seconds. Pressing the MUSIC TYPE button
or turning the TUNE/SCROLL control knob within five
seconds will allow the program format type to be sePush the rotary TUNE/SCROLL control knob a third
lected. Many radio stations do not currently broadcast
time and TREBLE will display. Turn the TUNE/SCROLL
Music Type information.
control knob to the right or left to increase or decrease the
Toggle the MUSIC TYPE button to select the following
treble tones.
format types:
Push the rotary TUNE/SCROLL control knob a fourth
Program Type
16-Digit Character Display
time and BALANCE will display. Turn the TUNE/
No program type or
SCROLL control knob to the right or left to adjust the
None
undefined
sound level from the right or left side speakers.
Adult Hits
Adlt Hit
Push the rotary TUNE/SCROLL control knob a fifth time
Classical
Classicl
and FADE will display. Turn the TUNE/SCROLL control
Classic Rock
Cls Rock
knob to the left or right to adjust the sound level between
College
College
the front and rear speakers.
Country
Country
Push the rotary TUNE/SCROLL control knob again to
Foreign Language
Language
exit setting tone, balance, and fade.
UNDERSTANDING YOUR INSTRUMENT PANEL 353
Program Type
Information
Jazz
News
Nostalgia
Oldies
Personality
Public
Rhythm and Blues
Religious Music
Religious Talk
Rock
Soft
Soft Rock
Soft Rhythm and Blues
Sports
Talk
16-Digit Character Display
Inform
Jazz
News
Nostalga
Oldies
Persnlty
Public
R&B
Rel Musc
Rel Talk
Rock
Soft
Soft Rck
Soft R&B
Sports
Talk
Program Type
Top 40
Weather
16-Digit Character Display
Top 40
Weather
By pressing the SEEK button when the Music Type icon
is displayed, the radio will be tuned to the next frequency
station with the same selected Music Type name. The
Music Type function only operates when in the FM
mode.
If a preset button is activated while in the Music Type
(Program Type) mode, the Music Type mode will be
exited and the radio will tune to the preset station.
SETUP Button
Pressing the SETUP button allows you to select between
the following items:
• Set Clock — Pressing the SELECT button will allow
you to set the clock. Adjust the hours by turning the
TUNE/SCROLL control knob. After adjusting the
4
354 UNDERSTANDING YOUR INSTRUMENT PANEL
hours, press the TUNE/SCROLL control knob to set
the minutes. The minutes will begin to blink. Adjust
the minutes using the right side TUNE/SCROLL
control knob. Press the TUNE/SCROLL control knob
to save time change.
AM/FM Button
Press the button to select either AM or FM mode.
SET/RND Button — To Set the Pushbutton
Memory
When you are receiving a station that you wish to
commit to pushbutton memory, press the SET/RND
button. The symbol SET 1 will now show in the display
window. Select the button (1–6) you wish to lock onto this
station and press and release that button. If a button is
not selected within five seconds after pressing the SET/
RND button, the station will continue to play but will not
be stored into pushbutton memory.
You may add a second station to each pushbutton by
repeating the above procedure with this exception: Press
the SET/RND button twice and SET 2 will show in the
display window. Each button can be set for SET 1 and
SET 2 in both AM and FM. This allows a total of 12 AM
and 12 FM stations to be stored into pushbutton memory.
The stations stored in SET 2 memory can be selected by
pressing the pushbutton twice.
Every time a preset button is used, a corresponding
button number will display.
Buttons 1 - 6
These buttons tune the radio to the stations that you
commit to pushbutton memory (12 AM and 12 FM
stations).
DISC/AUX Button
Pressing the DISC/AUX button will allow you to switch
from AM/FM modes to DISC/AUX mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 355
If you insert a disc with the ignition ON/RUN and the
radio ON, the unit will switch from radio to CD mode
and begin to play when you insert the disc. The display
NOTE:
will show the track number, and index time in minutes
• The ignition switch must be in the ON/RUN or ACC
and seconds. Play will begin at the start of track 1.
position to operate the radio.
Operation Instructions — CD MODE for CD and
MP3 Audio Play
• This radio is capable of playing compact discs (CD),
recordable compact discs (CD-R), rewritable compact
discs (CD-RW), compact discs with MP3 tracks and
multisession compact discs with CD and MP3 tracks.
CAUTION!
• This CD player will accept 4–3/4 in (12 cm) discs
only. The use of other sized discs may damage the
CD player mechanism.
• Do not use adhesive labels. These labels can peel
away and jam the player mechanism.
• The RES Media Center is a single CD player. Do
not attempt to insert a second CD if one is already
loaded.
Inserting Compact Disc(s)
Gently insert one CD into the CD player with the CD
label facing up. The CD will automatically be pulled into
the CD player and the CD icon will illuminate on the
radio display. If a CD does not go into the slot more than
1.0 in (2.5 cm), a disc may already be loaded and must be
ejected before a new disc can be loaded.
EJECT Button - Ejecting a CD
Press the EJECT button to eject the CD.
4
356 UNDERSTANDING YOUR INSTRUMENT PANEL
If you have ejected a disc and have not removed it within RW/FF
10 seconds, it will be reloaded. If the CD is not removed, Press and hold FF (Fast Forward) and the CD player will
begin to fast forward until FF is released or RW or
the radio will reinsert the CD but will not play it.
another CD button is pressed. The RW (Reverse) button
A disc can be ejected with the radio and ignition OFF.
works in a similar manner.
NOTE: Ejecting with the ignition OFF is not allowed on
AM/FM Button
convertible or soft-top models (if equipped).
Press the button to select either AM or FM mode.
SEEK Button
SET/RND Button (Random Play Button)
Press the right SEEK button for the next selection on the
Press this button while the CD is playing to activate
CD. Press the left SEEK button to return to the beginning
Random Play. This feature plays the selections on the
of the current selection, or return to the beginning of the
compact disc in random order to provide an interesting
previous selection if the CD is within the first second of
change of pace.
the current selection. Pressing and holding the SEEK
button will allow faster scrolling through the tracks in Press the right SEEK button to move to the next randomly selected track.
CD and MP3 modes.
TIME Button
Press the SET/RND button a second time to stop RanPress this button to change the display from a large CD dom Play.
playing time display to a small CD playing time display.
UNDERSTANDING YOUR INSTRUMENT PANEL 357
Notes On Playing MP3 Files
• Maximum number of files: 255
The radio can play MP3 files; however, acceptable MP3
• Maximum number of folders. (The radio display of file
file recording media and formats are limited. When
names and folder names is limited. For large numbers
writing MP3 files, pay attention to the following restricof files and/or folders, the radio may be unable to
tions.
display the file name and folder name and will assign
Supported Media (Disc Types)
a number instead. With a maximum number of files,
The MP3 file recording media supported by the radio are
exceeding 20 folders will result in this display. With
CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
200 files, exceeding 50 folders will result in this
display.)
Supported Medium Formats (File Systems)
The medium formats supported by the radio are ISO 9660 • Maximum number of characters in file/folder names:
Level 1 and Level 2 and includes the Joliet extension.
• Level 1: 12 (including a separator ⬙.⬙ and a threeWhen reading discs recorded using formats other than
character extension)
ISO 9660 Level 1 and Level 2, the radio may fail to read
• Level 2: 31 (including a separator ⬙.⬙ and a threefiles properly and may be unable to play the file norcharacter extension)
mally. UDF and Apple HFS formats are not supported.
The radio uses the following limits for file systems:
• Maximum number of folder levels: 8
Multisession disc formats are supported by the radio.
Multisession discs may contain combinations of normal
CD audio tracks and computer files (including MP3 files).
4
358 UNDERSTANDING YOUR INSTRUMENT PANEL
Discs created with an option such as ⬙keep disc open after
writing⬙ are most likely multisession discs. The use of
multisession for CD audio or MP3 playback may result in
longer disc loading times.
Supported MP3 File Formats
The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3
extension may cause playback problems. The radio is
designed to recognize the file as an invalid MP3 and will
not play the file.
When using the MP3 encoder to compress audio data to
an MP3 file, the bit rate and sampling frequencies in the
following table are supported. In addition, variable bit
rates (VBR) are also supported. The majority of MP3 files
use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or
VBR bit rates.
MPEG
Specification
Sampling Frequency (kHz)
MPEG-1 Audio
Layer 3
48, 44.1, 32
MPEG-2 Audio
Layer 3
24, 22.05, 16
Bit Rate (kbps)
320, 256, 224,
192, 160, 128,
112, 96, 80, 64,
56, 48, 40, 32
160, 128, 144,
112, 96, 80, 64,
56, 48, 40, 32, 24,
16, 8
ID3 Tag information for artist, song title, and album title
are supported for version 1 ID3 tags. ID3 version 2 is not
supported by the radios.
Playlist files are not supported. MP3 Pro files are not
supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 359
Playback of MP3 Files
When a medium containing MP3 data is loaded, the
radio checks all files on the medium. If the medium
contains a lot of folders or files, the radio will take more
time to start playing the MP3 files.
LIST Button (CD Mode for MP3 Play)
Pressing the LIST button will bring up a list of all folders
on the disc. Scrolling up or down the list is done by
turning the TUNE/SCROLL control knob. Selecting a
folder by pressing the TUNE/SCROLL control knob will
begin playing the files contained in that folder (or the
Loading times for playback of MP3 files may be affected
next folder in sequence if the selection does not contain
by the following:
playable files).
• Media - CD-RW media may take longer to load than
The folder list will time out after five seconds.
CD-R media
INFO Button (CD Mode for MP3 Play)
• Medium formats - Multisession discs may take longer
Pressing the INFO button repeatedly will scroll through
to load than non-multisession discs
the following TAG information: Song Title, Artist, File
• Number of files and folders - Loading times will Name, and Folder Name (if available).
increase with more files and folders
Press the INFO button once more to return to ⬙elapsed
To increase the speed of disc loading, it is recommended time⬙ priority mode.
to use CD-R media and single-session discs. To create a
Press and hold the INFO button for three seconds or
single-session disc, enable the “Disc at Once” option
more and the radio will display song titles for each file.
before writing to the disc.
4
360 UNDERSTANDING YOUR INSTRUMENT PANEL
Press and hold the INFO button again for three seconds
to return to ⬙elapsed time⬙ display.
Operation Instructions - Auxiliary Mode
The auxiliary (AUX) jack is an audio input jack which
allows the user to plug in a portable device such as an
MP3 player or cassette player and utilize the vehicle’s
audio system to amplify the source and play through the
vehicle speakers.
Uconnect™ Multimedia (Satellite Radio) —
If Equipped
Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to
coast. The subscription service provider is Sirius Satellite
Radio. This service offers over 130 channels of music,
sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
Pressing the AUX button will change the mode to auxil- NOTE: Sirius service is not available in Hawaii and has
limited coverage in Alaska.
iary device if the AUX jack is connected.
NOTE: The AUX device must be turned on and the System Activation
device’s volume set to the proper level. If the AUX audio is Sirius Satellite Radio service is pre-activated, and you
not loud enough, turn the device’s volume up. If the AUX may begin listening immediately to the one year of audio
service that is included with the factory-installed satellite
audio sounds distorted, turn the device’s volume down.
radio system in your vehicle. Sirius will supply a welTIME Button (Auxiliary Mode)
come kit that contains general information, including
Press this button to change the display to time of day. The how to setup your on-line listening account. For further
time of day will display for five seconds (when the information, call the toll-free number 888-539-7474,
ignition is OFF).
UNDERSTANDING YOUR INSTRUMENT PANEL 361
or visit the Sirius web site at www.sirius.com, or at Sirius ID number will display. The Sirius ID number
display will time out in two minutes. Press any button on
www.siriuscanada.ca for Canadian residents.
the radio to exit this screen.
Electronic Serial Number/Sirius Identification
Number (ESN/SID)
Selecting Uconnect™ Multimedia (Satellite) Mode
Please have the following information available when Press the SAT button until ⬙SAT⬙ appears in the display.
calling:
A CD may remain in the radio while in the Satellite radio
mode.
1. The Electronic Serial Number/Sirius Identification
Satellite Antenna
Number (ESN/SID).
To ensure optimum reception, do not place items on the
2. Your Vehicle Identification Number.
roof around the rooftop antenna location. Metal objects
placed within the line of sight of the antenna will cause
To access the ESN/SID, refer to the following steps:
decreased performance. Larger luggage items such as
ESN/SID Access
bikes should be placed as far rearward as possible, within
With the ignition switch in the ON/RUN or ACC posithe loading design of the rack. Do not place items directly
tion and the radio on, press the SETUP button and scroll
on or above the antenna.
using the TUNE/SCROLL control knob until Sirius ID is
selected. Press the TUNE/SCROLL control knob and the
4
362 UNDERSTANDING YOUR INSTRUMENT PANEL
Reception Quality
SEEK Buttons
Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next
channel in Satellite mode. Press the right switch to seek
following reasons:
up and the left switch to seek down. The radio will
• The vehicle is parked in an underground parking
remain tuned to the new channel until you make another
structure or under a physical obstacle.
selection. Holding either button will bypass channels
• Dense tree coverage may interrupt reception in the without stopping until you release it.
form of short audio mutes.
SCAN Button
• Driving under wide bridges or along tall buildings can Pressing the SCAN button causes the tuner to search for
the next channel, pausing for eight seconds before concause intermittent reception.
tinuing to the next. To stop the search, press the SCAN
• Placing objects over or too close to the antenna can button a second time.
cause signal blockage.
INFO Button
Operating Instructions - Uconnect™ Multimedia
Pressing the INFO button will cycle the display informa(Satellite) Mode
tion between Artist, Song Title, and Composer (if availNOTE: The ignition switch must be in the ON/RUN or able). Also, pressing and holding the INFO button for an
additional three seconds will make the radio display the
ACC position to operate the radio.
Song Title all of the time (press and hold again to return
to normal display).
UNDERSTANDING YOUR INSTRUMENT PANEL 363
By pressing the SEEK button when the Music Type
RW/FF
Pressing the RW (Rewind) or FF (Fast Forward) buttons function is active, the radio will be tuned to the next
causes the tuner to search for the next channel in the channel with the same selected Music Type name.
direction of the arrows.
If a preset button is activated while in the Music Type
(Program Type) mode, the Music Type mode will be
TUNE Control (Rotary)
Turn the rotary TUNE/SCROLL control knob clockwise exited and the radio will tune to the preset channel.
to increase or counterclockwise to decrease the channel.
SETUP Button
MUSIC TYPE Button
Pressing the SETUP button allows you to select the
Pressing this button once will turn on the Music Type following items:
mode for five seconds. Pressing the MUSIC TYPE button • Display Sirius ID number — Press the AUDIO/
or turning the TUNE/SCROLL control knob within five
SELECT button to display the Sirius ID number. This
seconds will allow the program format type to be senumber is used to activate, deactivate, or change the
lected.
Sirius subscription.
Toggle the MUSIC TYPE button again to select the music SET Button – To Set the Pushbutton Memory
type.
When you are receiving a channel that you wish to
commit to pushbutton memory, press the SET button.
The symbol SET 1 will now show in the display window.
4
364 UNDERSTANDING YOUR INSTRUMENT PANEL
Select the button (1-6) you wish to lock onto this channel
and press and release that button. If a button is not
selected within five seconds after pressing the SET button, the channel will continue to play but will not be
stored into pushbutton memory.
You may add a second channel to each pushbutton by
repeating the above procedure with this exception: Press
the SET button twice and SET 2 will show in the display
window. Each button can be set for SET 1 and SET 2. This
allows a total of 12 Satellite channels to be stored into
pushbutton memory. The channels stored in SET 2
memory can be selected by pressing the pushbutton twice.
Every time a preset button is used, a corresponding
button number will display.
Buttons 1 - 6
These buttons tune the radio to the channels that you
commit to pushbutton memory (12 Satellite stations).
Operating Instructions (Uconnect™ Phone) —
If Equipped
Refer to “Uconnect™ Phone” in the Uconnect™ User
Manual located on the DVD for further details.
iPod姞/USB/MP3 CONTROL — IF EQUIPPED
NOTE: This section is for sales code RES and REQ/
REL/RET radios only with Uconnect™. For sales code
RBZ/RHB, RHR, RHP, RHW or RB2 touch-screen radio
iPod威/USB/MP3 control feature, refer to the separate
RBZ/RHB, RHR, RHP, RHW or RB2 User’s Manual.
iPod威/USB/MP3 control is available only if equipped as
an option with these radios.
UNDERSTANDING YOUR INSTRUMENT PANEL 365
This feature allows an iPod威 or external USB device to be Connecting The iPod姞 Or External USB Device
plugged into the USB port, located in the center console. Use the connection cable to connect an iPod威 or external
USB device to the vehicle’s USB/AUX connector port
iPod威 control supports Mini, 4G, Photo, Nano, 5G iPod威
which is located in the center console.
and iPhone威 devices. Some iPod威 software versions may
not fully support the iPod威 control features. Please visit
Apple’s website for software updates.
4
NOTE:
• If the radio has a USB port, refer to the appropriate
Uconnect™ Multimedia radio User’s Manual for
iPod威 or external USB device support capability.
• Connecting an iPod威 or consumer electronic audio
device to the AUX port located in the radio faceplate,
plays media, but does not use the iPod威 /MP3 control
feature to control the connected device.
Center Console USB/AUX Connector Port
NOTE: The center console will have a position where
the iPod威 or consumer electronic audio device cable can
366 UNDERSTANDING YOUR INSTRUMENT PANEL
be routed through without damaging the cable when
closing the lid. A factory cut out space for the cable to be
routed may be located in the base of the center console on
either the front or side. This allows routing of the cable
without damaging it while closing the lid. If a cut out is
not available in the center console base, route the cable
away from the lid latch and in a place that will allow the
lid to close without damaging the cable.
Second Row USB Charging Port
The second row USB connector port can be used for
charging purposes only. Use the connection cable to
connect an iPod威 or external USB device to the vehicle’s
USB charging port which is located in the second row
center console.
Once the audio device is connected and synchronized to
the vehicle’s iPod威/USB/MP3 control system (iPod威 or
external USB device may take a few minutes to connect),
the audio device starts charging and is ready for use by
pressing radio switches, as described below.
NOTE: If the audio device battery is completely discharged, it may not communicate with the iPod威/USB/
MP3 control system until a minimum charge is attained.
Leaving the audio device connected to the iPod威/USB/
MP3 control system may charge it to the required level.
Second Row Center Console USB Charging Port
UNDERSTANDING YOUR INSTRUMENT PANEL 367
NOTE: If the device battery to be charged is completely on the radio faceplate or press the VR button and say
⬙USB⬙ or ⬙Switch to USB⬙. Once in the iPod威/USB/MP3
depleted, it may take awhile to charge.
control mode, audio tracks (if available from audio
Using This Feature
device) start playing over the vehicle’s audio system.
By using iPod cable or external USB device to connect to
Play Mode
USB port:
When switched to iPod威/USB/MP3 control mode, the
• The audio device can be played on the vehicle’s sound
iPod威 or external USB device automatically starts Play
system, providing metadata (artist, track title, album,
mode. In Play mode, the following buttons on the radio
etc.) information on the radio display.
faceplate may be used to control the iPod威 or external
• The audio device can be controlled using the radio USB device and display data:
buttons to Play, Browse, and List the iPod威 contents.
• Use the TUNE control knob to select the next or
previous track.
• The audio device battery charges when plugged into
the USB/AUX connector (if supported by the specific
• Turning it clockwise (forward) by one click, while
audio device)
playing a track, skips to the next track or press the
Controlling The iPod姞 Or External USB Device
VR button and say ⬙Next Track⬙.
Using Radio Buttons
To get into the iPod威/USB/MP3 control mode and access
a connected audio device, either press the “AUX” button
4
368 UNDERSTANDING YOUR INSTRUMENT PANEL
• Turning it counterclockwise (backward) by one • While a track is playing, press the INFO button to see
click, will jump to the previous track in the list or
the associated metadata (artist, track title, album, etc.)
press the VR button and say ⬙Previous Track⬙
for that track. Pressing the INFO button again jumps
to the next screen of data for that track. Once all
• Jump backward in the current track by pressing and
screens have been viewed, the last INFO button press
holding the << RW button. Holding the << RW
will go back to the play mode screen on the radio.
button long enough will jump to the beginning of
• Pressing the REPEAT button will change the audio
the current track.
device mode to repeat the current playing track or
• Jump forward in the current track by pressing and
press the VR button and say ⬙Repeat ON⬙ or ⬙Repeat
holding the FF >> button.
Off⬙.
• A single press backward << RW or forward FF >> will
• Press the SCAN button to use iPod威/USB/MP3 dejump backward or forward respectively, for five
vice scan mode, which will play the first 10 seconds of
seconds.
each track in the current list and then forward to the
• Use the << SEEK and SEEK >> buttons to jump to the
next song. To stop SCAN mode and start playing the
previous or next track. Pressing the SEEK >> button
desired track, when it is playing the track, press the
during play mode will jump to the next track in the
SCAN button again. During Scan mode, pressing the
list, or press the VR button and say ⬙Next or Previous
<< SEEK and SEEK >> buttons will select the previTrack⬙.
ous and next tracks.
UNDERSTANDING YOUR INSTRUMENT PANEL 369
• RND button (available on sales code RES radio only):
Pressing this button toggles between Shuffle ON and
Shuffle OFF modes for the iPod威 or external USB
device, or press the VR button and say ⬙Shuffle ON⬙ or
⬙Shuffle Off⬙. If the RND icon is showing on the radio
display, then the shuffle mode is ON.
List Or Browse Mode
During Play mode, pressing any of the buttons described
below, will bring up List mode. List mode enables
scrolling through the list of menus and tracks on the
audio device.
• TUNE control knob: The TUNE control knob functions
in a similar manner as the scroll wheel on the audio
device or external USB device.
• Turning it clockwise (forward) and counterclockwise (backward) scrolls through the lists, displaying
the track detail on the radio display. Once the track
to be played is highlighted on the radio display,
press the TUNE control knob to select and start
playing the track. Turning the TUNE control knob
fast will scroll through the list faster. During fast
scroll, a slight delay in updating the information on
the radio display may be noticeable.
• During all List modes, the iPod威 displays all lists in
“wrap-around” mode. So if the track is at the
bottom of the list, just turn the wheel backward
(counterclockwise) to get to the track faster.
• In List mode, the radio PRESET buttons are used as
shortcuts to the following lists on the iPod威 or
external USB device.
• Preset 1 – Playlists
• Preset 2 – Artists
• Preset 3 – Albums
• Preset 4 – Genres
4
370 UNDERSTANDING YOUR INSTRUMENT PANEL
• Preset 5 – Audiobooks
• Preset 6 – Podcasts
• Pressing a PRESET button will display the current
list on the top line and the first item in that list on
the second line.
• To exit List mode without selecting a track, press the
same PRESET button again to go back to Play
mode.
• LIST button: The LIST button will display the top
level menu of the iPod威 or external USB device. Turn
the TUNE control knob to list the top-menu item to be
selected and press the TUNE control knob. This will
display the next sub-menu list item on the audio
device, then follow the same steps to go to the desired
track in that list. Not all iPod威 or external USB device
sub-menu levels are available on this system.
• MUSIC TYPE button: The MUSIC TYPE button is
another shortcut button to the genre listing on your
audio device.
CAUTION!
• Leaving the iPod威 or external USB device (or any
supported device) anywhere in the vehicle in
extreme heat or cold can alter the operation or
damage the device. Follow the device manufacturer’s guidelines.
• Placing items on the iPod威 or external USB device,
or connections to the iPod威 or external USB device
in the vehicle, can cause damage to the device
and/or to the connectors.
UNDERSTANDING YOUR INSTRUMENT PANEL 371
WARNING!
Do not plug in or remove the iPod威 or external USB
device while driving. Failure to follow this warning
could result in an accident.
phone system. Seven devices can be paired to the
Uconnect™ phone system, but just one can be selected
and played.
Selecting Different Audio Device
1. Press PHONE button to begin.
Bluetooth Streaming Audio (BTSA)
2. After the ⬙Ready⬙ prompt and the following beep, say
Music can be streamed from your cellular phone to the
⬙Setup⬙, then ⬙Select Audio Devices⬙.
Uconnect™ phone system.
3. Say the name of the audio device or ask the
Controlling BTSA Using Radio Buttons
Uconnect™ phone system to list audio devices.
To get into the BTSA mode, press either “AUX” button on
the radio or press the VR button and say “Bluetooth Next Track
Use the SEEK UP button, or press the VR button on the
Streaming Audio”.
radio and say “Next Track” to jump to the next track
Play Mode
music on your cellular phone.
When switched to BTSA mode, some audio devices can
start playing music over the vehicle’s audio system, but
some devices require the music to be initiated on the
device first, then it will get streamed to the Uconnect™
4
372 UNDERSTANDING YOUR INSTRUMENT PANEL
Previous Track
Use the SEEK DOWN button, or press the VR button on
the radio and say “Previous Track” to jump to the
previous track music on your cellular phone.
Browse
Browsing is not available on a BTSA device. Only the
current song that is playing will display info.
UCONNECT™ MULTIMEDIA VIDEO
ENTERTAINMENT SYSTEM (VES)™ —
IF EQUIPPED
Getting Started
Overhead Video Screen
• Screen located in the overhead console: Unfold the • With the ignition switch in the ON or ACC position,
turn the radio on by pushing the ON/OFF Volume
overhead LCD screen by pushing the button in the
Control knob.
center of the overhead console behind the screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 373
• When the Video Screen are open and a DVD is inserted Or
into the VES™ player, the screen turns on automatiPress the LOAD button then corresponding number (1–6)
cally, the headphone transmitters turn on and playwhere the DVD is to be loaded (Non-Touch-Screen).
back begins.
2. Insert the DVD with the label facing up. The radio
Single Video Screen
automatically selects the appropriate mode after the disc
NOTE: Typically there are two different ways to operate is recognized and displays the menu screen or starts
the features of the Video Entertainment System (VES)™. playing the first track.
• The Remote Control
• The Touch-Screen Radio (If Equipped)
Play A DVD
1. Press the OPEN/CLOSE or LOAD hard-key on the
radio faceplate (Touch-Screen).
3. Ensure the VES™ Remote Control and the Headphone
switch is on Channel 1.
4
374 UNDERSTANDING YOUR INSTRUMENT PANEL
Using The Remote Control
1. Press the MODE button on the Remote Control.
NOTE: The VES™ system will retain the last setting
when turned off.
Using The Touch-Screen Radio Controls
2. While looking at the video screen, highlight DISC by
either pressing Up/Down/Left/Right buttons or by re- 1. Press the MENU hard-key on the radio faceplate.
peatedly pressing the MODE button, then press ENTER
2. Touch the Rear VES soft-key to display the Rear VES
on the Remote Control.
Controls. If a channel list appears on the right side of the
screen, touch the HIDE LIST soft-key to display the Rear
VES Controls screen.
Select DISC Mode On The VES Screen
UNDERSTANDING YOUR INSTRUMENT PANEL 375
4
Rear VES Soft-key
Select Channel/Screen 1 And DISC
In The MEDIA Column
3. Touch the 1 soft-key and then the DISC soft-key in the
MEDIA column. To exit touch the back arrow soft-key at NOTE:
• To view a DVD on the radio press the RADIO/MEDIA
the top left of the screen.
hard-key, on the radio faceplate, then touch the DISC
tab soft-key and then the VIEW VIDEO soft-key.
376 UNDERSTANDING YOUR INSTRUMENT PANEL
• Viewing a DVD on the Touch-Screen radio screen is Play Video Games
not available in all states/provinces, and the vehicle Connect the video game console to the Auxiliary RCA
must be stopped, and the shift lever must be in the input jacks located on the back of the center console.
PARK position for vehicles with automatic transmission. In vehicles with manual transmission the parking
brake must be engaged.
• Touching the screen on a Touch-Screen radio while a
DVD is playing brings up basic remote control functions for DVD play such as scene selection, Play,
Pause, FF, RW, and Stop. Pressing the X in the upper
corner will turn off the remote control screen
functions.
1. Video In – Yellow
2. Left Audio In – White
3. Right Audio In – Red
UNDERSTANDING YOUR INSTRUMENT PANEL 377
When connecting an external source to the AUX input, be
sure to follow the standard color coding for the VES™
jacks:
NOTE: Certain high-end video games, such as Playstation3 and XBox360 will exceed the power limit of the
vehicle’s Power Inverter. Refer to the Power Inverter
section in your vehicle’s Owner’s Manual for more
information.
4
Ensure the Remote Control and Headphone switch is on
Channel 1.
Using The Remote Control
1. Press the MODE button on the Remote Control.
2. While looking at the video screen, highlight VES AUX
1, by either pressing Up/Down/Left/Right buttons or by
repeatedly pressing the MODE button, then press ENTER
on the Remote Control.
Select VES AUX1 Mode On The VES Screen
378 UNDERSTANDING YOUR INSTRUMENT PANEL
Using The Touch-Screen Radio Controls
1. Press the MENU hard-key on the radio faceplate.
3. Touch the 1 soft-key and then touch AUX 1 in the VES
column. To exit press the back arrow soft-key at the top of
the screen.
2. Touch the Rear VES soft-key to display the Rear VES
Controls. If a channel list is displayed, press the HIDE
LIST soft-key to display the Rear VES Controls screen.
Select Channel/Screen 1 And
AUX 1 In The VES Column
Rear VES Soft-key
UNDERSTANDING YOUR INSTRUMENT PANEL 379
Listen To An Audio Source On Channel 2 While A
Video Is Playing On Channel 1
Ensure the Remote Control and Headphone switch is on
Channel 2.
Using The Remote Control
1. Press the MODE button on the Remote Control and
the Mode Select Screen will display, unless a video is
playing then only a small banner will appear on the
bottom of the screen.
2. While looking at the video screen, either press Up/
Down/Left/Right on the Remote Control to highlight the
desired audio source or repeatedly press the MODE
button on the remote until the desired audio source
appears on the screen.
4
Select FM Mode On The VES Screen
380 UNDERSTANDING YOUR INSTRUMENT PANEL
3. To listen to an audio source on Channel 2 while a
video is playing on Channel 1, touch the 2 soft-key and
1. Press the MENU hard-key on the radio faceplate.
choose an audio source. To exit touch the back arrow
2. Touch the Rear VES soft-key to display the Rear VES soft-key at the top left of the left screen.
Controls. If a channel list is displayed, press the HIDE
LIST soft-key to display the Rear VES Controls screen.
Using The Touch-Screen Radio Controls
Select Channel/Screen 2 And HDD
In The MEDIA Column
Rear VES Soft-key
UNDERSTANDING YOUR INSTRUMENT PANEL 381
Important Notes For Single Video Screen System
Play A DVD Using The Touch-Screen Radio
• VES™ is able to transmit two channels of stereo audio 1. Press the OPEN/CLOSE or LOAD hard-key on the
simultaneously.
radio faceplate (Touch-Screen).
• In split screen mode the left side equates to Channel 1 2. Insert the DVD with the label facing up. The radio
and right side equates to Channel 2.
automatically selects the appropriate mode after the disc
is recognized and displays the menu screen or starts
• If a video source is selected on Channel 1, then
playing the first track.
Channel 2 is for audio only. Selecting a video source
(DVD) will not show the video on the screen.
3. To watch a DVD on Screen 1 for second row passengers, ensure the Remote Control and Headphone switch
• When selecting a video source on Channel 1, the video
is on Channel 1.
will display on the screen and the audio could be
heard on Channel 1 in the headphones.
• Audio can be heard through the headphones even
when the Video Screen is closed
4
382 UNDERSTANDING YOUR INSTRUMENT PANEL
Using The Remote Control
1. Press the MODE button on the Remote Control.
NOTE:
• Channel/Screen 1 select mode information is shown
on the left side of the screen.
2. While looking at Screen 1, highlight DISC by either
• Channel/Screen 2 select mode information is shown
pressing Up/Down/Left/Right buttons or by repeatedly
on the right side of the screen.
pressing the MODE button, then press ENTER.
• The VES™ will retain the last setting when turned off.
Using The Touch-Screen Radio Controls
1. Press the MENU hard-key on the radio faceplate.
2. Touch the Rear VES soft-key to display the Rear VES
Controls. If a channel list is displayed, press the HIDE
LIST soft-key to display the Rear VES Controls screen.
Select DISC Mode On The VES Screen
UNDERSTANDING YOUR INSTRUMENT PANEL 383
4
Rear VES Soft-key
Select Channel/Screen 1 And DISC
In The MEDIA Column
3. Touch the 1 or 2 soft-key and then the DISC soft-key in
the MEDIA column. To exit touch the back arrow at the NOTE:
• To view a DVD on the radio press the RADIO/MEDIA
top left of the screen.
hard-key, on the radio faceplate, then touch the DISC
tab soft-key and then the VIEW VIDEO soft-key.
384 UNDERSTANDING YOUR INSTRUMENT PANEL
• Viewing a DVD on the Touch-Screen radio screen is Remote Control
not available in all states/provinces, and the vehicle
must be stopped, and the shift lever must be in the
PARK position for vehicles with automatic transmission. In vehicles with manual transmission the parking
brake must be engaged.
• Touching the screen on a Touch-Screen radio while a
DVD is playing brings up basic remote control functions for DVD play such as scene selection, Play,
Pause, FF, RW, and Stop. Pressing the X in the upper
corner will turn off the remote control screen
functions.
Remote Control
Controls And Indicators
1. Power – Turns the screen and wireless headphone
transmitter for the selected Channel on or off. To hear
audio while the screen is closed, press the Power button
to turn the headphone transmitter on.
UNDERSTANDING YOUR INSTRUMENT PANEL 385
2. Channel Selector Indicators – When a button is 6. 䉲 / Prev – In radio modes, press to select to the
pressed, the currently affected channel or channel button previous station. In disc modes, press to advance to the
start of the current or previous audio track or video
is illuminated momentarily.
chapter. In menu modes, use to navigate in the menu.
3. Light – Turns the remote control backlighting on or off.
The remote backlighting turns off automatically after five 7. MENU – Press to return to the main menu of a DVD
disc, to select a satellite audio or video channel from the
seconds.
Station list, or select playback modes (SCAN/RANDOM
4. Channel/Screen Selector Switch - Indicates which
for a CD).
channel is being controlled by the remote control. When
the selector switch is in the Channel 1 position, the 8. 䉴 / 㥋 (Play/Pause) – Begin/resume or pause disc play.
remote controls the functionality of screen Channel 1
9. 䡲 (Stop) – Stops disc play
(right side of the screen). When the selector switch is in
the Channel 2, position the remote controls the function- 10. PROG Up/Down – When listening to a radio mode,
ality of screen Channel 2 (left side of the screen).
pressing PROG Up selects the next preset and pressing
PROG Down selects the previous preset stored in the
5. 䉴䉴 – In radio modes, press to seek the next tunable
radio. When listening to compressed audio on a data
station. In disc modes, press and hold to fast forward
disc, PROG Up selects the next directory and PROG
through the current audio track or video chapter. In
Down selects the previous directory. When listening to a
menu modes use to navigate in the menu.
4
386 UNDERSTANDING YOUR INSTRUMENT PANEL
disc in a radio with a multiple-disc changer, PROG Up mode is selected and the disc is stopped, press the SETUP
selects the next disc and PROG Down selects the previ- button to access the DVD Setup menu. (see the DVD
Setup Menu of this manual.)
ous disc.
11. MUTE – Press to mute the headphone audio output 16. BACK – When navigating in menu mode, press to
for the selected channel.
return to the previous screen. When navigating a DVDs
disc menu, the operation depends on the disc’s contents.
12. SLOW – Press to slow playback of a DVD disc. Press
17. 䉳䉳 – In radio modes, press to seek to the previous
play (䉴) to resume normal play.
tunable station. In disc modes, press and hold to fast
13. STATUS – Press to display the current status.
rewind through the current audio track or video chapter.
14. MODE – Press to change the mode of the selected In menu modes use to navigate in the menu.
channel. See the Mode Selection section of this manual
18. ENTER – Press to select the highlighted option in a
for details on changing modes.
menu.
15. SETUP – When in a video mode, press the SETUP
19. 䉱 / NEXT – In radio modes, press to select to the
button to access the display settings (see the display
next station. In disc modes, press to advance to the next
settings section) or the DVD Setup menu. When a disc is
audio track or video chapter. In menu modes, use to
loaded in the DVD player (if equipped) and the VES™
navigate in the menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 387
Remote Control Storage
The video screen(s) come with a built in storage compartment for the remote control which is accessible when the
screen is opened. To remove the remote, use your index
finger to pull and rotate the remote towards you. Do not
try to pull the remote straight down as it will be very
difficult to remove. To return the remote back into its
storage area, insert one long edge of the remote into the
two retaining clips first, and then rotate the remote back
up into the other two retaining clips until it snaps back
into position.
4
The Remote Control Storage
Locking The Remote Control
All remote control functionality can be disabled as a
parental control feature.
• To disable the Remote Control from making any
changes, press the Video Lock button on the DVD
player (if equipped). If the vehicle is not equipped
388 UNDERSTANDING YOUR INSTRUMENT PANEL
with a DVD player, follow the radio’s instructions to Headphones Operation
turn Video Lock on. The radio and the video screen(s) The headphones receive two separate channels of audio
using an infrared transmitter from the video screen.
indicate when Video Lock is active.
• Pressing the Video Lock again or turning the ignition Front seat occupants receive some headphone audio
OFF turns Video Lock OFF and allows remote control coverage to allow them to adjust the headphone volume
operation of the VES™.
for the young rear seat occupants that may not be able to
do so for themselves.
Replacing The Batteries
The remote control requires two AAA batteries for op- If no audio is heard after increasing the volume control,
eration. To replace the batteries:
verify that the screen is turned on and in the down
position and that the channel is not muted and the
• Locate the battery compartment on the back of the
headphone channel selector switch is on the desired
remote, then slide the battery cover downward.
channel. If audio is still not heard, check that fully
• Replace the batteries, making sure to orient them charged batteries are installed in the headphones.
according to the polarity diagram shown.
• Replace the battery compartment cover.
UNDERSTANDING YOUR INSTRUMENT PANEL 389
NOTE: The rear video system must be turned on before
sound can be heard from the headphones. To conserve
battery life, the headphones will automatically turn off
approximately three minutes after the rear video system
is turned off.
Changing the Audio Mode for Headphones
1. Ensure the Remote Control channel/screen selector
switch is in the same position as the headphone selector
switch..
1.
2.
3.
4.
Volume Control
Power Button
Channel Selection Switch
Power Indicator
Controls
The headphone power indicator and controls are located
on the right ear cup.
NOTE:
• When both switches are on Channel 1, the Remote is
controlling Channel 1 and the headphones are tuned
to the audio of the VES™ Channel 1.
• When both switches are on Channel 2, the Remote is
controlling Channel 2 and the headphones are tuned
to the audio of the VES™ Channel 2.
2. Press the MODE button on the remote control.
4
390 UNDERSTANDING YOUR INSTRUMENT PANEL
3. If the video screen is displaying a video source (such
as a DVD Video), pressing DISPLAY shows the status on
a popup banner at the bottom of the screen. Pressing the
MODE button will advance to the next mode. When the
mode is in an audio only source (such as FM), the Mode
Selection menu appears on screen.
Replacing The Batteries
Each set of headphones requires two AAA batteries for
operation. To replace the batteries:
• Locate the battery compartment on the left ear cup of
the headphones, and then slide the battery cover
downward.
4. When the Mode Selection menu appears on screen,
• Replace the batteries, making sure to orient them
use the cursor buttons on the remote control to navigate
according to the polarity diagram shown.
to the available modes and press the ENTER button to
• Replace the battery compartment cover.
select the new mode.
5. To cancel out of the Mode Selection menu, press the Unwired姞 Stereo Headphone Lifetime Limited
Warranty
BACK button on the remote control.
Who Does This Warranty Cover? This warranty covers
the initial user or purchaser (⬙you⬙ or ⬙your⬙) of this
particular Unwired Technology LLC (⬙Unwired⬙) wireless headphone (⬙Product⬙). The warranty is not transferable.
UNDERSTANDING YOUR INSTRUMENT PANEL 391
How Long Does The Coverage Last? This warranty lasts NATURE WHATSOEVER. Some states and jurisdictions
may not allow the exclusion or limitation of incidental or
as long as you own the Product.
consequential damages, so the above limitation may not
What Does This Warranty Cover? Except as specified
apply to you. This warranty gives you specific legal
below, this warranty covers any Product that in normal
rights. You may also have other rights, which vary from
use is defective in workmanship or materials.
jurisdiction to jurisdiction.
What Does This Warranty Not Cover? This warranty What Will Unwired威 Do? Unwired威, at its option, will
does not cover any damage or defect that results from repair or replace any defective Product. Unwired威 remisuse, abuse or modification of the Product other than serves the right to replace any discontinued Product with
by Unwired. Foam earpieces, which will wear over time a comparable model. THIS WARRANTY IS THE SOLE
through normal use, are specifically not covered (replace- WARRANTY FOR THIS PRODUCT, SETS FORTH YOUR
ment foam is available for a nominal charge). UNWIRED EXCLUSIVE REMEDY REGARDING DEFECTIVE
TECHNOLOGY IS NOT LIABLE FOR ANY INJURIES PRODUCTS, AND IS IN LIEU OF ALL OTHER WAROR DAMAGES TO PERSONS OR PROPERTY RESULT- RANTIES (EXPRESS OR IMPLIED), INCLUDING ANY
ING FROM THE USE OF, OR ANY FAILURE OR DE- WARRANTY OR MERCHANTABILITY OR FITNESS
FECT IN, THE PRODUCT, NOR IS UNWIRED LIABLE FOR A PARTICULAR PURPOSE.
FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT,
INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, PU- If you have any questions or comments regarding your
NITIVE OR OTHER DAMAGES OF ANY KIND OR Unwired威 wireless headphones, please phone 1-888-2933332 or email [email protected]
4
392 UNDERSTANDING YOUR INSTRUMENT PANEL
You may register your Unwired威 wireless headphones mode, but not change stations until the radio mode is
online at www.unwiredtechnology.com or by phone at changed to a mode that is different from the VES™
selected radio mode. When shared, the radio has priority
1-888-293-3332.
over the VES™ or all radio modes (FM, AM, and SAT).
System Information
The VES™ has the ability to switch tuner (AM/FM),
SEEK, SCAN, TUNE, and recall presets in radio modes as
Shared Modes
The VES™ and radio are capable of communicating with long as it is not in shared mode.
each other. This allows the VES™ to output radio audio
When in shared disc mode both the radio and the VES™
to the headphones and the radio to output VES™ audio
have control of the video functions. The VES™ has the
to the vehicle speakers. When the radio and VES™ are in
ability to control the following video modes:
the same (shared) mode, a VES™ icon will be visible on
the radio’s display and the shared icon will be visible on 1. CD: Ability to Fast Forward, Rewind, Scan, and Track
the VES™ screen. When in shared mode, the same audio Up/Down.
source is heard in the headphones and vehicle speakers
2. CD Changer (in radio): Ability to Disk Up/Down and
simultaneously.
program all listed CD controls (Fast Forward, Rewind,
If the radio functions (FM, AM, or SAT) are in the shared Scan, and Track Up/Down).
mode with the VES™, only the radio is able to control the
radio functions. In this case, VES™ can share the radio
UNDERSTANDING YOUR INSTRUMENT PANEL 393
The VES™ can even control radio modes or video modes 1. Channel 1 Mode
while the radio is turned off. The VES™ can access the
2. Channel 1 Shared Status
radio modes or disc modes by navigating to those modes
on the VES™ and activating a radio mode or disc mode. 3. Channel 1 Audio Only/Mute
Information Mode Display
4. Channel 2 Mode
5. Channel 2 Shared Status
6. Channel 2 Audio Only/Mute
7. Channel 1 ENTER Button Action
8. Channel 2 ENTER Button Action
9. Clock
10. Video Lock
11. Not Available / Error
12. Disc Changer Status
Information Mode Video Screen Display
4
394 UNDERSTANDING YOUR INSTRUMENT PANEL
Numeric Keypad Menu
When the display for either Channel 1 or Channel 2
shows DIRECT TUNE, pressing the remote control’s
ENTER button activates a numeric keypad menu. This
screen makes it easy to enter a specific tuner frequency,
satellite channel, or track number. To enter the desired
digit:
1. Press the remote control’s navigation buttons (䉱, 䉲,
䉴, 䉳) to navigate to the desired digit.
2. When the digit is highlighted, press the remote control’s ENTER button to select the digit. Repeat these steps
until all digits are entered.
Numeric Keypad Menu
3. To delete the last digit, navigate to the Del button and
press the remote control’s ENTER button.
4. After all of the digits are entered, navigate to the Go
button and press the remote control’s ENTER button.
UNDERSTANDING YOUR INSTRUMENT PANEL 395
Station List Menu
Disc Menu
4
Channel Selection Menu For SIRIUS Backseat TV™
When listening to Satellite audio or watching SIRIUS
Backseat TV™ (if equipped), pressing the remote control’s MENU button displays a list of all available channels. Navigate this list using the remote control’s navigation buttons (䉱, 䉲) to find the desired station, press the
remote control’s ENTER button to tune to that station. To
jump through the list more quickly, navigate to the Page
Up and Page Down icons on the screen.
Disc Menu For CDs
When listening to a CD Audio or CD Data disc, pressing
the remote control’s MENU button displays a list of all
commands which control playback of the disc. Using the
options you can activate or cancel Scan play and Random
play.
396 UNDERSTANDING YOUR INSTRUMENT PANEL
Display Settings
settings are already set for optimum viewing, so there is
no need to change these settings under normal circumstances.
To change the settings, press the remote control’s navigation buttons (䉱, 䉲) to select an item, then press the
remote control’s navigation buttons (䉴, 䉳) to change the
value for the currently selected item. To reset all values
back to the original settings, select the Default Settings
menu option and press the remote control’s ENTER
button.
Video Screen Display Settings
When watching a video source (DVD Video with the disc
in Play mode, Aux Video, SIRIUS Backseat TV™, etc.),
pressing the remote control’s SETUP button activates the
Display Settings menu. These settings control the appearance of the video on the screen. The factory default
Disc Features control the remote DVD player’s (if
equipped) settings of DVD being watched in the remote
player.
Listening To Audio With The Screen Closed
To listen to only audio portion of the channel with the
screen closed:
• Set the audio to the desired source and channel.
UNDERSTANDING YOUR INSTRUMENT PANEL 397
• Close the video screen.
Disc Formats
The VES™ DVD player is capable of playing the follow• To change the current audio mode, press the remote
ing types of discs (12 mm or 8 mm diameter):
control’s MODE button. This will automatically select
the next available audio mode without using the Mode • DVD-Video discs (MPEG-2 video compression) (see
notes about DVD Region Codes)
Select menu.
• When the screen is reopened, the video screen will • DVD-Audio discs (2 channel audio output only)
automatically turn back on and show the appropriate
• Audio Compact Discs (CDs)
display menu or media.
• CD Data discs with MP3 and WMA compressed audio
If the screen is closed and there is no audio heard, verify
format files
that the headphones are turned on (the ON indicator is
illuminated) and the headphone selector switch is on the • Video CDs (MPEG-1 video compression)
desired channel. If the headphones are turned on, press
DVD Region Codes
the remote control’s power button to turn audio on. If
audio is still not heard, check that fully charged batteries The VES™ DVD player and many DVD discs are coded
by geographic region. These region codes must match in
are installed in the headphones.
order for the disc to play. If the region code for the DVD
disc does not match the region code for the player, the
disc will not play and will be ejected.
4
398 UNDERSTANDING YOUR INSTRUMENT PANEL
If you record a disc using a personal computer, there may
be cases where the VES™ DVD player may not be able to
When a DVD-Audio disc is inserted in the VES™ DVD
play some or the entire disc, even if it is recorded in a
player, the DVD-Audio title on the disc is played by
compatible format and is playable on other players. To
default (most DVD-Audio discs also have a Video title,
help avoid playback problems, use the following guidebut the Video title is ignored). All multi-channel program
lines when recording discs.
material is automatically mixed down to two channels,
which may result in a lowered apparent volume level. If • Open sessions are ignored. Only sessions that are
closed are playable.
you increase the volume level to account for this change
in level, remember to lower the volume before changing
• For multi-session CDs that contain only multiple CDthe disc or to another mode.
Audio sessions, the player will renumber the tracks so
each track number is unique.
Recorded Discs
DVD Audio Support
The VES™ DVD player will play CD-R and CD-RW discs • For CD Data (or CD-ROM) discs, always use the
ISO-9660 (Level 1 or Level 2), Joliet, or Romeo format.
recorded in CD-Audio or Video-CD format, or as a
Other formats (such as UDF, HFS, or others) are not
CD-ROM containing MP3 or WMA files. The player will
supported.
also play DVD-Video content recorded to a DVD-R or
DVD-RW disc. DVD-ROM discs (either pressed or re• The player recognizes a maximum of 512 files and 99
corded) are not supported.
folders per CD-R and CD-RW disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 399
• Mixed media recordable DVD formats will only play
the Video_TS portion of the disc.
end with the extension ⬙.mp3⬙ or ⬙.MP3⬙ and WMA
files must always end with the extension ⬙.wma⬙ or
⬙.WMA⬙. To prevent incorrect playback, do not use
these extensions for any other types of files.
If you are still having trouble writing a disc that is
playable in the VES™ DVD player, check with the disc
recording software publisher for more information about • For MP3 files, only version 1 ID3 tag data (such as
artist name, track title, album, etc.) are supported.
burning playable discs.
The recommended method for labeling recordable discs • Any file that is copy protected (such as those downloaded from many online music stores) will not play.
(CD-R, CD-RW, and DVD-R) is with a permanent marker.
The DVD player will automatically skip the file and
Do not use adhesive labels as they may separate from the
begin playing the next available file.
disc, become stuck, and cause permanent damage to the
DVD player.
• Other compression formats such as AAC, MP3 Pro,
Ogg Vorbis, and ATRAC3 will not play. The DVD
Compressed Audio Files (MP3 and WMA)
player will automatically skip the file and begin playThe DVD player is capable of playing MP3 (MPEG-1
ing the next available file.
Audio Layer 3) and WMA (Windows Media Audio) files
• If you are creating your own files, the recommended
from a CD Data disc (usually a CD-R or CD-RW).
fixed bit rate for MP3 files is between 96 and 192Kbps
• The DVD player always uses the file extension to
and the recommended fixed bit rate for WMA files is
determine the audio format, so MP3 files must always
4
400 UNDERSTANDING YOUR INSTRUMENT PANEL
between 64 and 192Kbps. Variable bit rates are also If a disc has a damaged track which results in audible or
supported. For both formats, the recommended visible errors that persists for 2.0 seconds, the DVD
player will attempt to continue playing the disc by
sample rate is either 44.1kHz or 48kHz.
skipping forward 1.0 to 3.0 seconds at a time. If the end
• To change the current file, use the remote control’s or
of the disc is reached, the DVD player will return to the
DVD player’s 䉱 button to advance to the next file, or
beginning of the disc and attempt to play the start of the
the 䉲 button to return to the start of the current or
first track.
previous file.
The DVD player may shut down during extremely hot
• To change the current directory, use the remote conconditions, such as when the vehicle’s interior temperatrol’s PROG Up and Down buttons.
ture is above 120°F. When this occurs, the DVD player
Disc Errors
will display ⬙VES High Temp⬙ and will shut off the VES™
displays until a safe temperature is reached. This shutIf the DVD player is unable to read the disc, a ⬙Disc Error⬙
down is necessary to protect the optics of the DVD
message is displayed on the VES™ and Radio displays
player.
and the disc is automatically ejected. A dirty, damaged, or
incompatible disc format are all potential causes for a
⬙Disc Error⬙ message.
UNDERSTANDING YOUR INSTRUMENT PANEL 401
Display
Other Language Setup
All of the Language settings have a special ⬙Other⬙ setting
to accommodate languages other than Japanese or English. These languages are selected using a special fourdigit code.
To enter a new language code, activate the DVD Setup
Menu and follow these additional instructions:
• Using the remote control Up and Down cursor buttons, highlight the Language item you want to edit,
and then press the remote control ENTER button.
• Using the remote control Down cursor button, select
the ⬙Other⬙ setting, then press the remote control’s
Right cursor button to begin editing the setting.
DVD Player Language Menu
• Using the remote control Up and Down cursor buttons, select a digit for the current position. After
selecting the digit, press the remote control’s Right
cursor button to select the next digit. Repeat this digit
selection sequence for all four digits.
4
402 UNDERSTANDING YOUR INSTRUMENT PANEL
• When the entire four-digit code is entered, press the
remote control’s ENTER button. If the language code
is not valid, the numbers all change back to ⬙*⬙. If the
digits are visible after this step, then the language code
is valid.
them where lower numbers are designated for all audiences and higher numbers are designated for more adult
audiences.
When a DVD-Video disc is loaded, its rating is compared
to the setting in the DVD player. If the rating of the disc
Here is an abbreviated list of language codes. For more is higher than the setting in the player, a Password screen
language codes, please contact the dealer where the is displayed. In order to watch the disc, the rear passenvehicle was purchased.
ger must enter the correct password using the password
entry method described below.
Language
Code
Language
Code
Dutch
German
Portuguese
2311
1304
2519
French
Italian
Spanish
1517
1819
1418
To play all discs without requiring a password, set the
DVD player’s rating to Level 8. Setting the rating to Level
1 always requires the password to play any DVD disc.
Not all DVD discs encode a Rating, so it is still possible
Rating and Password Setup
that discs designed for adult audiences can still play
The Rating and Password settings work together to without requiring a password.
control the types of DVDs that your family watches. Most
The default rating is Level 8 (play all discs without a
DVD-Video discs have a rating (from 1 to 8) assigned to
password) and the default password is 0000.
UNDERSTANDING YOUR INSTRUMENT PANEL 403
To set the password, activate the DVD Setup Menu and
follow these additional instructions:
• Using the remote control Left and Right cursor buttons, select the Rating tab.
• Highlight ⬙Change Password⬙, and then press the
remote control’s ENTER button.
• Enter the current password. Select a digit, use the
remote control Up and Down cursor buttons to set the
value for the current digit, and then press the remote
control’s Right cursor button to select the next digit.
Repeat this digit selection sequence for all four digits.
• After the four-digit password is entered, press the
remote control’s ENTER button. If the password is
correct, the set password screen is displayed.
DVD Password Entry
• Using the remote control’s Up and Down cursor
buttons to set the value for the current digit and the
remote control’s Right cursor button to select digits,
enter the new password.
4
404 UNDERSTANDING YOUR INSTRUMENT PANEL
• After the four-digit password is entered, press the To set the rating, activate the DVD Setup Menu and
remote control’s ENTER button to accept the change. follow these additional instructions:
• Using the remote control’s Left and Right cursor
buttons, select the Rating tab.
• Highlight ⬙Change Rating⬙, and then press the remote
control’s ENTER button.
• Enter the current password. Select a digit, use the
remote control’s Up and Down cursor buttons to set
the value for the current digit, and then press the
remote control’s Right cursor button to select the next
digit. Repeat this digit selection sequence for all four
digits.
• After the four-digit password is entered, press the
remote control’s ENTER button. If the password is
correct, the Rating Level menu is displayed.
DVD Player Level Menu
UNDERSTANDING YOUR INSTRUMENT PANEL 405
Dolby威 Digital and MLP Lossless Manufactured
• Using the remote control’s Up and Down cursor
under license from Dolby Laboratories. ⬙Dolby⬙,
buttons, select the new rating level, and then press the
remote control’s ENTER button to accept the change. ⬙MLP Lossless⬙, and the double-D symbol are trademarks
of Dolby Laboratories. Confidential unpublished works.
Product Agreement
Copyright 1992-1997 Dolby Laboratories. All right reThis product incorporates copyright protection technolserved.
ogy that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection General Information
technology must be authorized by Macrovision, and is
This system complies with Part 15 of the FCC Operation
intended for home or other limited viewing uses otheris subject to the following two conditions:
wise authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
4
406 UNDERSTANDING YOUR INSTRUMENT PANEL
STEERING WHEEL AUDIO CONTROLS
The remote sound system controls are located on the rear
surface of the steering wheel. Reach behind the wheel to
access the switches.
The right-hand control is a rocker-type switch with a
pushbutton in the center and controls the volume and
mode of the sound system. Pressing the top of the rocker
switch will increase the volume, and pressing the bottom
of the rocker switch will decrease the volume.
Pressing the center button will make the radio switch
between the various modes available (AM/FM/SAT/
CD/HDD/AUX/VES, etc.).
The left-hand control is a rocker-type switch with a
pushbutton in the center. The function of the left-hand
control is different depending on which mode you are in.
The following describes the left-hand control operation in
each mode.
Remote Sound System Controls
(Back View Of Steering Wheel)
Radio Operation
Pressing the top of the switch will “Seek” up for the next
listenable station and pressing the bottom of the switch
will “Seek” down for the next listenable station.
UNDERSTANDING YOUR INSTRUMENT PANEL 407
The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE
will tune to the next preset station that you have pro- To keep a CD/DVD in good condition, take the following
precautions:
grammed in the radio preset pushbutton.
CD Player
Pressing the top of the switch once will go to the next
track on the CD. Pressing the bottom of the switch once
will go to the beginning of the current track, or to the
beginning of the previous track if it is within one second
after the current track begins to play.
1. Handle the disc by its edge; avoid touching the
surface.
2. If the disc is stained, clean the surface with a soft cloth,
wiping from center to edge.
3. Do not apply paper or tape to the disc; avoid scratching the disc.
If you press the switch up or down twice, it plays the
second track; three times, it will play the third, etc.
4. Do not use solvents such as benzene, thinner, cleaners,
or anti-static sprays.
The center button on the left side rocker switch has no
function for a single-disc CD player. However, when a 5. Store the disc in its case after playing.
multiple-disc CD player is equipped on the vehicle, the
6. Do not expose the disc to direct sunlight.
center button will select the next available CD in the
player.
7. Do not store the disc where temperatures may become
too high.
4
408 UNDERSTANDING YOUR INSTRUMENT PANEL
NOTE: If you experience difficulty in playing a particu- Dual-Zone Automatic Temperature Control (ATC)
lar disc, it may be damaged (i.e., scratched, reflective — If Equipped
coating removed, a hair, moisture or dew on the disc)
• The Automatic Temperature Control (ATC) allows
oversized, or have protection encoding. Try a known
both driver and front passenger seat occupants to
good disc before considering disc player service.
select individual comfort settings.
RADIO OPERATION AND MOBILE PHONES
• When occupants in the vehicle select the AUTO mode
Under certain conditions, the mobile phone being on in
operation, a comfort temperature can be set by using
your vehicle can cause erratic or noisy performance from
the temperature up and down buttons, and the auto
your radio. This condition may be lessened or eliminated
blower operation will be set automatically.
by relocating the mobile phone antenna. This condition is
not harmful to the radio. If your radio performance does • The system provides set-and-forget operation for optimum comfort and convenience.
not satisfactorily “clear” by the repositioning of the
antenna, it is recommended that the radio volume be • The system can be controlled manually, if desired.
turned down or off during mobile phone operation when
The ATC system automatically maintains the interior
not using Uconnect™ (if equipped).
comfort level desired by the driver and passenger.
CLIMATE CONTROLS
The air conditioning and heating system is designed to
make you comfortable in all types of weather.
UNDERSTANDING YOUR INSTRUMENT PANEL 409
2. Recirculation Control Button
Press and release to change the current setting, the
indicator illuminates when ON.
3. Left Front Seat Occupant Temperature Display
This display shows the temperature setting for the left
front seat occupant.
4. Mode Display
This display shows the current Mode selection (Panel,
Bi-Level, Floor, Mix).
Automatic Temperature Control (ATC) Panel
1. A/C Button
Press and release to change the current Air Conditioning
(A/C) setting, the indicator illuminates when A/C is ON.
Performing this function will cause the ATC to switch
into manual mode.
5. Blower Control Display
This display shows the current Blower speed selection.
6. Right Front Seat Occupant Temperature Display
This display shows the temperature setting for the right
front seat occupant.
7. Front Defrost Button
Press and release to change the current setting, the
indicator illuminates when ON. Performing this function
4
410 UNDERSTANDING YOUR INSTRUMENT PANEL
will cause the ATC to switch into manual mode. The 11. Blower Control
blower will engage immediately if the Defrost mode is There are seven blower speeds, the blower speed increases as you move the control to the right from the
selected.
lowest blower setting. Performing this function will
8. Passenger Temperature Control Up Button
cause the ATC to switch into manual mode.
Provides the passenger with independent temperature
control. Push the button for warmer temperature set- 12. Climate Control ON/OFF Button
Press and release to turn the Climate Control ON/OFF
tings.
9. Passenger Temperature Control Down Button
13. Mode Control Button
Provides the passenger with independent temperature Press and release to select between Modes (Panel, Bicontrol. Push the button for cooler temperature settings. Level, Floor, Mix). Performing this function will cause the
ATC to switch into manual mode.
10. Auto Temperature Control Button
Controls airflow temperature, distribution, volume, and 14. SYNC Button
the amount of air recirculation automatically. Press and Press and release to control the temperature setting for
release to select. Refer to “Automatic Operation” for both zones from the driver temperature control.
more information. Performing this function will cause
15. Driver Temperature Control Down Button
the ATC to switch between manual mode and automatic
Provides the driver with independent temperature conmodes.
trol. Push the button for cooler temperature settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 411
3. When the system is set up for your comfort level, it is
16. Driver Temperature Control Up Button
Provides the driver with independent temperature con- not necessary to change the settings. You will experience
the greatest efficiency by simply allowing the system to
trol. Push the button for warmer temperature settings.
function automatically.
17. Rear Control Button
Provides the rear seat occupants with independent NOTE:
blower and temperature control. Push the button to • It is not necessary to move the temperature settings for
cold or hot vehicles. The system automatically adjusts
activate the rear climate control and allow the rear seat
the temperature, mode and fan speed to provide
occupants control of the rear blower and temperature
comfort as quickly as possible.
settings.
• The temperature can be displayed in U.S. or Metric
units by selecting the US/M customer-programmable
1. Press the AUTO button on the Automatic Temperature
feature. Refer to the “Electronic Vehicle Information
Control (ATC) Panel.
Center (EVIC) — Customer-Programmable Features
2. Next, adjust the temperature you would like the
(SETUP)” in this section of the manual.
system to maintain by adjusting the driver and front
To provide you with maximum comfort in the Automatic
passenger temperature control buttons. Once the desired
mode, during cold start-ups the blower fan will remain
temperature is displayed, the system will achieve and
on low until the engine warms up. The blower will
automatically maintain that comfort level.
increase in speed and transition into Auto mode.
Automatic Operation
4
412 UNDERSTANDING YOUR INSTRUMENT PANEL
selected. This allows the front occupants to control the
Manual Operation
This system offers a full complement of manual override volume of air circulated in the vehicle and cancel the
features.
Auto mode.
NOTE: Each of these features operate independently The operator can also select the direction of the airflow
from each other. If any one feature is controlled manually, by selecting one of the following positions.
temperature control will continue to operate automatiPanel Mode
cally.
Air comes from the outlets in the instrument panel.
Each of these outlets can be individually adjusted to
There are seven fixed blower speeds.
Use the outer dial control to regulate direct the flow of air. The air vanes of the center outlets
the amount of air forced through the and outboard outlets can be moved up and down or side
system in any mode you select. The to side to regulate airflow direction. There is a shut off
blower speed increases as you move wheel located below the air vanes to shut off or adjust the
the control clockwise and decreases amount of airflow from these outlets.
Blower Control when you move the control counter- Bi-Level Mode
clockwise.
Air comes from the instrument panel outlets, floor
The blower fan speed can be set to any fixed speed by
outlets and defrost outlets.
adjusting the blower control outer dial. The fan will now
operate at a fixed speed until additional speeds are
UNDERSTANDING YOUR INSTRUMENT PANEL 413
NOTE: In many temperature positions, the BI-LEVEL temperature settings for best windshield and side winmode is designed to provide cooler air out of the panel dow defrosting. When the defrost mode is selected, the
blower will automatically default to medium-high unless
outlets and warmer air from the floor outlets.
the blower is controlled manually.
Floor Mode
Air comes from the floor outlets. A slight amount of NOTE: While operating in the other modes, the system
air is directed through the defrost and side window will not automatically sense the presence of fog, mist or
ice on the windshield. Defrost mode must be manually
demister outlets.
selected to clear the windshield and side glass.
Mix Mode
Air comes from the floor, defrost and side window Air Conditioning (A/C)
demist outlets. This mode works best in cold or The Air Conditioning (A/C) button allows the operator
snowy conditions. It allows you to stay comfortable to manually activate or deactivate the air conditioning
system. When in A/C mode and the ATC is set to a cool
while keeping the windshield clear.
temperature, dehumidified air flows through the air
Defrost Mode
outlets. If Economy mode is desired, press the A/C
Air comes from the windshield and side window
button to turn off the A/C mode in the ATC display and
demist outlets. Use Defrost mode with maximum
deactivate the A/C system.
4
414 UNDERSTANDING YOUR INSTRUMENT PANEL
NOTE:
• If the system is in Mix, Floor or Defrost Mode, the A/C
can be turned off, but the A/C system shall remain
active to prevent fogging of the windows.
NOTE: In cold weather, use of Recirculation mode may
lead to excessive window fogging. The Recirculation
mode is not allowed in the Defrost modes to improve
window clearing operation. Recirculation will be disabled automatically if this mode is selected.
• If fog or mist appears on the windshield or side glass,
Rear Climate Control — If Equipped
select Defrost mode and increase blower speed.
The Rear Climate Control system has floor air outlets,
Recirculation Control
and overhead outlets at each outboard rear seating
When outside air contains smoke, odors, or
position. The unit provides warm or cool air through the
high humidity, or if rapid cooling is desired,
floor and upper outlets.
you may wish to recirculate interior air by
pressing the Recirculation control button. Re- The rear blower and temperature controls for the rear
circulation mode should only be used temporarily. The seat passengers are located in the headliner, near the
recirculation LED will illuminate when this button is center of the vehicle.
selected. Push the button a second time to turn off the
If the rear system is off, changing the rear setting to a
Recirculation mode LED and allow outside air into the
position other than off will turn the rear system on. If
vehicle.
both the front and rear systems are off, turning the rear
system on from the rear controls will also turn on the
front system on.
UNDERSTANDING YOUR INSTRUMENT PANEL 415
Only when the Rear Control Icon is illuminated do the
second row seat occupants have control of the rear
blower speed.
The rear blower control, located in the rear overhead
console, has an off position and a range of blower speeds.
This allows the second row seat occupants to control the
volume of air circulated in the rear of the vehicle.
CAUTION!
Rear Manual Climate Controls
1 – Rear Blower
2 – Rear Climate Control Icon
3 – Rear Temperature
Rear Blower Control
The primary control for the rear blower is on the front
climate control unit, located on the instrument panel.
Interior air enters the Rear Manual Climate Control
system through an intake grille, located in the right
side trim panel behind the third row seats. The
heater outlets are located in the right side trim panel,
just behind the sliding door. Do not block or place
objects directly in front of the inlet grille or heater
outlets. The electrical system could overload, causing
damage to the blower motor.
4
416 UNDERSTANDING YOUR INSTRUMENT PANEL
NOTE: In many temperature positions, the BI-LEVEL
Rear Temperature Control
Only when the Rear Control Icon is illuminated do the mode is designed to provide cooler air out of the headsecond row seat occupants have control of the rear mode liner outlets and warmer air from the floor outlets.
control knob.
Floor Mode
Air comes from the floor outlets.
To change the temperature in the rear of the vehicle,
rotate the temperature control knob counterclockwise for
cold air, and clockwise for heated air.
Operating Tips
Rear Mode Control
Window Fogging
Windows will fog on the inside when the humidity inside
Headliner Mode
Air comes from the outlets in the headliner. Each of the vehicle is high. This often occurs in mild or cool
these outlets can be individually adjusted to direct temperatures when it’s rainy or humid. In most cases,
the flow of air. Moving the air vanes of the outlets to one turning the air conditioning (pressing the A/C button) on
will clear the fog. Adjust the temperature control, air
side will shut off the airflow.
direction, and blower speed to maintain comfort.
Bi-Level Mode
Air comes from both the headliner outlets and the As the temperature gets colder, it may be necessary to
direct air onto the windshield. Adjust the temperature
floor outlets.
control and blower speed to maintain comfort. Higher
UNDERSTANDING YOUR INSTRUMENT PANEL 417
blower speeds will reduce fogging. Interior fogging on Winter Operation
the windshield can be quickly removed by selecting the When operating the system during the winter months,
make sure the air intake, located directly in front of the
DEFROST mode.
windshield, is free of ice, slush, snow, or other
Regular cleaning of the inside of the windows with a
obstructions.
non-filming cleaning solution (vinegar and water works
very well) will help prevent contaminates (cigarette Vacation Storage
smoke, perfumes, etc.) from sticking to the windows. Anytime you store your vehicle, or keep it out of service
(i.e. vacation) for two weeks or more, run the air condiContaminates increase the rate of window fogging.
tioning system at idle for about five minutes in the fresh
Summer Operation
air and high blower setting. This will ensure adequate
NOTE: In some cases during high temperature trailer system lubrication to minimize the possibility of comtow operation the Air Conditioning system performance pressor damage when the system is started again.
may be reduced. This is to help protect the engine from
overheating during the high load condition.
Your air conditioning system is also equipped with an
automatic recirculation system. When the system senses
a heavy load or high heat conditions, it may use partial
Recirculation A/C mode to provide additional comfort.
4
418 UNDERSTANDING YOUR INSTRUMENT PANEL
Operating Tips Chart
STARTING AND OPERATING
CONTENTS
䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 424
䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 430
▫ Automatic Transmission . . . . . . . . . . . . . . . 424
▫ Key Ignition Park Interlock . . . . . . . . . . . . . 432
▫ Keyless Enter-N-Go – If Equipped . . . . . . . . 425
▫ Brake/Transmission Shift Interlock System . . 432
▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 426
▫ Five-Speed Automatic Transmission
(3.6L Engine) — If Equipped . . . . . . . . . . . . 432
▫ Extreme Cold Weather
(Below –20°F Or ⫺29°C) . . . . . . . . . . . . . . . 428
▫ If Engine Fails To Start . . . . . . . . . . . . . . . . 428
▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . 429
䡵 Engine Block Heater — If Equipped . . . . . . . . 429
▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . 433
▫ Six-Speed Automatic Transmission
(5.7L Engine) — If Equipped . . . . . . . . . . . . 440
▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . 441
5
420 STARTING AND OPERATING
䡵 All-Wheel Drive Operation . . . . . . . . . . . . . . . 450
▫ After Driving Off-Road . . . . . . . . . . . . . . . . 460
▫ Single-Speed Operating Instructions/
Precautions (3.6L Engine) – If Equipped . . . . 450
䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . 461
▫ Electronically Shifted Transfer Case
(Three-Position Switch) (5.7L Engine) – If
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 450
▫ Shifting Procedure . . . . . . . . . . . . . . . . . . . 454
䡵 On-Road Driving Tips . . . . . . . . . . . . . . . . . . 457
䡵 Off-Road Driving Tips . . . . . . . . . . . . . . . . . . 457
▫ When To Use Low Range – If Equipped . . . . 457
▫ Driving Through Water . . . . . . . . . . . . . . . . 457
▫ Driving In Snow, Mud And Sand . . . . . . . . . 459
▫ Hill Climbing . . . . . . . . . . . . . . . . . . . . . . . 459
▫ Traction Downhill . . . . . . . . . . . . . . . . . . . . 460
▫ 3.6L Engine . . . . . . . . . . . . . . . . . . . . . . . . 461
▫ 5.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . 463
▫ Power Steering Fluid Check . . . . . . . . . . . . . 464
䡵 Multi-Displacement System (MDS)
(If Equipped) — 5.7L Engine Only . . . . . . . . . . 465
䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . 465
䡵 Electronic Brake Control System . . . . . . . . . . . 467
▫ Anti-Lock Brake System (ABS) . . . . . . . . . . . 468
▫ Traction Control System (TCS) . . . . . . . . . . . 468
▫ Brake Assist System (BAS) . . . . . . . . . . . . . . 469
▫ Electronic Roll Mitigation (ERM) . . . . . . . . . 470
STARTING AND OPERATING 421
▫ Electronic Stability Control (ESC) . . . . . . . . . 470
䡵 Tires — General Information
. . . . . . . . . . . . . 488
▫ Trailer Sway Control (TSC) . . . . . . . . . . . . . 474
▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . 488
▫ Hill Start Assist (HSA) . . . . . . . . . . . . . . . . 474
▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . 489
▫ Ready Alert Braking . . . . . . . . . . . . . . . . . . 477
▫ Tire Pressures For High Speed Operation . . . 491
▫ Rain Brake Support . . . . . . . . . . . . . . . . . . . 477
▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . 491
▫ ESC Malfunction Indicator Light And ESC
Off Indicator Light . . . . . . . . . . . . . . . . . . . 477
▫ Spare Tire Matching Original Equipped Tire
And Wheel – If Equipped . . . . . . . . . . . . . . 491
䡵 Tire Safety Information
. . . . . . . . . . . . . . . . . 478
▫ Compact Spare Tire – If Equipped . . . . . . . . 492
▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . 478
▫ Full Size Spare – If Equipped . . . . . . . . . . . . 493
▫ Tire Identification Number (TIN) . . . . . . . . . 482
▫ Limited-Use Spare – If Equipped . . . . . . . . . 493
▫ Tire Terminology And Definitions . . . . . . . . . 483
▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 494
▫ Tire Loading And Tire Pressure . . . . . . . . . . 484
▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . 494
▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . 495
5
422 STARTING AND OPERATING
▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . 496
▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . 512
䡵 Tire Chains (Traction Devices) . . . . . . . . . . . . . 497
▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . 513
䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 498
▫ Materials Added To Fuel . . . . . . . . . . . . . . . 514
䡵 Tire Rotation Recommendations . . . . . . . . . . . 499
▫ Fuel System Cautions . . . . . . . . . . . . . . . . . 514
䡵 Tire Pressure Monitor System (TPMS) . . . . . . . 500
▫ Carbon Monoxide Warnings . . . . . . . . . . . . 515
▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . 503 䡵 Flexible Fuel (3.6L Engine Only) —
If Equipped . . . . . . . . . . . . . . . . . . . . . .
▫ Premium System – If Equipped . . . . . . . . . . 505
▫ E-85 General Information . . . . . . . . . . .
▫ General Information . . . . . . . . . . . . . . . . . . 510
▫ Ethanol Fuel (E-85) . . . . . . . . . . . . . . .
䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 511
▫ Fuel Requirements . . . . . . . . . . . . . . .
▫ 3.6L Engine – If Equipped . . . . . . . . . . . . . . 511
▫ Selection Of Engine Oil For Flexible Fuel
▫ 5.7L Engine – If Equipped . . . . . . . . . . . . . . 511
Vehicles (E-85) And Gasoline Vehicles . .
▫ Reformulated Gasoline . . . . . . . . . . . . . . . . 512
▫ Starting . . . . . . . . . . . . . . . . . . . . . . .
▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . 512
▫ Cruising Range . . . . . . . . . . . . . . . . . .
. . . . 515
. . . . 515
. . . . 517
. . . . 517
. . . . 518
. . . . 518
. . . . 518
STARTING AND OPERATING 423
▫ Replacement Parts . . . . . . . . . . . . . . . . . . . 519
▫ Towing Requirements . . . . . . . . . . . . . . . . . 533
▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 519
▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 538
䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 519
䡵 Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . 539
▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . 519
䡵 Recreational Towing
(Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 540
▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 522
䡵 Vehicle Loading
. . . . . . . . . . . . . . . . . . . . . . 523
▫ Certification Label . . . . . . . . . . . . . . . . . . . 523
䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 525
▫ Common Towing Definitions . . . . . . . . . . . . 525
▫ Trailer Hitch Classification . . . . . . . . . . . . . . 530
▫ Trailer Towing Weights
(Maximum Trailer Weight Ratings) . . . . . . . . 531
▫ Trailer And Tongue Weight . . . . . . . . . . . . . 532
▫ Towing This Vehicle
Behind Another Vehicle . . . . . . . . . . . . . . . . 540
▫ Recreational Towing – Rear-Wheel Drive
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
▫ Recreational Towing – All-Wheel Drive
Models (Single-Speed Transfer Case) . . . . . . . 541
▫ Recreational Towing – All-Wheel Drive
Models (Two-Speed Transfer Case) . . . . . . . . 542
5
424 STARTING AND OPERATING
STARTING PROCEDURES
Before starting your vehicle, adjust your seat, adjust the
inside and outside mirrors, fasten your seat belt, and if
present, instruct all other occupants to buckle their seat
belts.
WARNING!
• When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children
to be in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Children should be
warned not to touch the parking brake, brake
pedal or the shift lever.
(Continued)
WARNING! (Continued)
• Do not leave the key fob in or near the vehicle, and
do not leave Keyless Enter-N-Go in the ACC or
ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
Automatic Transmission
The shift lever must be in the NEUTRAL or PARK
position before you can start the engine. Apply the brakes
before shifting into any driving gear.
CAUTION!
Damage to the transmission may occur if the following precautions are not observed:
• Shift into PARK only after the vehicle has come to
a complete stop.
(Continued)
STARTING AND OPERATING 425
CAUTION! (Continued)
• Shift into or out of REVERSE only after the
vehicle has come to a complete stop and the engine
is at idle speed.
• Do not shift from REVERSE, PARK, or NEUTRAL
into any forward gear when the engine is above
idle speed.
• Before shifting into any gear, make sure your foot
is firmly on the brake pedal.
Do not press the accelerator. Use the Fob with Integrated
Key to briefly turn the ignition switch to the START
position and release it as soon as the starter engages. The
starter motor will continue to run, and it will disengage
automatically when the engine is running. If the engine
fails to start, the starter will disengage automatically in
10 seconds. If this occurs, turn the ignition switch to the
LOCK position, wait 10 to 15 seconds, then repeat the
“Normal Starting” procedure.
Keyless Enter-N-Go – If Equipped
This feature allows the driver to operUsing Fob With Integrated Key (Tip Start)
ate the ignition switch with the push
NOTE: Normal starting of either a cold or a warm
of a button, as long as the ENGINE
engine is obtained without pumping or pressing the
START/STOP button is installed and
accelerator pedal.
the Remote Keyless Entry (RKE) transmitter is in the passenger compartment.
5
426 STARTING AND OPERATING
Installing And Removing The ENGINE
START/STOP Button
Installing The Button
1. Remove the key fob from the ignition switch.
NOTE: The ENGINE START/STOP button should only
be removed or inserted with the ignition in the LOCK
position (OFF position for Keyless Enter-N-Go).
Normal Starting
Using The ENGINE START/STOP Button
2. Insert the ENGINE START/STOP button into the
ignition switch with the lettering facing up and readable. NOTE: Normal starting of either a cold or a warm
engine is obtained without pumping or pressing the
3. Press firmly on the center of the button to secure it into
accelerator pedal.
position.
To start the engine, the transmission must be in PARK or
Removing The Button
NEUTRAL. Press and hold the brake pedal while press1. The ENGINE START/STOP button can be removed ing the ENGINE START/STOP button once. The system
takes over and attempts to start the vehicle. If the vehicle
from the ignition switch for key fob use.
fails to start, the starter will disengage automatically after
2. Insert the metal part of the emergency key under the
10 seconds. If you wish to stop the cranking of the engine
chrome bezel at the 6 o’clock position and gently pry the
prior to the engine starting, press the button again.
button loose.
STARTING AND OPERATING 427
NOTE: If the ignition switch is left in the ACC or RUN
(engine not running) position and the transmission is in
PARK, the system will automatically time out after
1. Place the shift lever in PARK, then press and release
30 minutes of inactivity and the ignition will switch to the
the ENGINE START/STOP button.
OFF position.
2. The ignition switch will return to the OFF position.
Keyless Enter-N-Go Functions – With Driver’s Foot
3. If the shift lever is not in PARK, the ENGINE START/ OFF The Brake Pedal (In PARK Or NEUTRAL
STOP button must be held for two seconds and vehicle Position)
speed must be above 5 mph (8 km/h) before the engine The Keyless Enter-N-Go feature operates similar to an
will shut off. The ignition switch position will remain in ignition switch. It has four positions, OFF, ACC, RUN
the ACC position until the shift lever is in PARK and the and START. To change the ignition switch positions
button is pressed twice to the OFF position. If the shift without starting the vehicle and use the accessories
lever is not in PARK and the ENGINE START/STOP follow these steps.
button is pressed once, the EVIC (if equipped) will
• Starting with the ignition switch in the OFF position:
display a “Vehicle Not In Park” message and the engine
will remain running. Never leave a vehicle out of the • Press the ENGINE START/STOP button once to
change the ignition switch to the ACC position (EVIC
PARK position, or it could roll.
displays “IGNITION MODE ACCESSORY”),
To Turn Off The Engine Using ENGINE
START/STOP Button
5
428 STARTING AND OPERATING
• Press the ENGINE START/STOP button a second time If Engine Fails To Start
to change the ignition switch to the RUN position
WARNING!
(EVIC displays “IGNITION MODE RUN”),
• Press the ENGINE START/STOP button a third time
to return the ignition switch to the OFF position (EVIC
displays “IGNITION MODE OFF”).
Extreme Cold Weather (Below –20°F Or ⫺29°C)
To ensure reliable starting at these temperatures, use of
an externally powered electric engine block heater (available from your authorized dealer) is recommended.
• Never pour fuel or other flammable liquids into
the throttle body air inlet opening in an attempt to
start the vehicle. This could result in a flash fire
causing serious personal injury.
• Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel
could enter the catalytic converter and once the
engine has started, ignite and damage the converter
and vehicle. If the vehicle has a discharged battery,
booster cables may be used to obtain a start from a
booster battery or the battery in another vehicle.
This type of start can be dangerous if done improperly. Refer to “Jump Starting” in “What To Do In
Emergencies” for further information.
STARTING AND OPERATING 429
Clearing A Flooded Engine
(Using ENGINE START/STOP Button)
If the engine fails to start after you have followed the
“Normal Starting” or “Extreme Cold Weather⬙ procedures, it may be flooded. To clear any excess fuel, press
and hold the brake pedal, push the accelerator pedal all
the way to the floor and hold it, then press and release the
ENGINE START/STOP button once. The starter motor
will engage automatically, run for 10 seconds, and then
disengage. Once this occurs, release the accelerator pedal
and the brake pedal, wait 10 to 15 seconds, then repeat
the “Normal Starting” procedure.
Clearing A Flooded Engine
(Using Fob With Integrated Key)
If the engine fails to start after you have followed the
“Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded. To clear any excess fuel, push
the accelerator pedal all the way to the floor and hold it.
Then, turn the ignition switch to the START position and
release it as soon as the starter engages. The starter motor
will disengage automatically in 10 seconds. Once this
occurs, release the accelerator pedal, turn the ignition
switch to the LOCK position, wait 10 to 15 seconds, then
repeat the “Normal Starting” procedure.
CAUTION!
To prevent damage to the starter, wait 10 to 15 seconds before trying again.
After Starting
The idle speed is controlled automatically and it will
decrease as the engine warms up.
ENGINE BLOCK HEATER — IF EQUIPPED
The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the heater cord to
a standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.
5
430 STARTING AND OPERATING
The engine block heater cord is located:
• 3.6L Engine – coiled and strapped to the engine oil
dipstick tube.
• 5.7L Engine – bundled and fastened to the injector
harness.
The engine block heater must be plugged in at least one
hour to have an adequate warming effect on the coolant.
WARNING!
Remember to disconnect the engine block heater
cord before driving. Damage to the 110-115 Volt AC
electrical cord could cause electrocution.
AUTOMATIC TRANSMISSION
CAUTION!
Damage to the transmission may occur if the following precautions are not observed:
• Shift into PARK only after the vehicle has come to
a complete stop.
• Shift into or out of REVERSE only after the
vehicle has come to a complete stop and the engine
is at idle speed.
• Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle
speed.
• Before shifting into any gear, make sure your foot
is firmly pressing the brake pedal.
STARTING AND OPERATING 431
WARNING!
WARNING! (Continued)
• Unintended movement of a vehicle could injure
those in or near the vehicle. As with all vehicles,
you should never exit a vehicle while the engine is
running. Before exiting a vehicle, always apply the
parking brake, shift the transmission into PARK,
and remove the key fob. Once the key fob is
removed, the shift lever is locked in the PARK
position, securing the vehicle against unwanted
movement.
• When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children
to be in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Children should be
warned not to touch the parking brake, brake
pedal or the shift lever.
• Do not leave the key fob in or near the vehicle, and
do not leave Keyless Enter-N-Go in the ACC or
ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
(Continued)
(Continued)
5
432 STARTING AND OPERATING
WARNING! (Continued)
• It is dangerous to move the shift lever out of PARK
or NEUTRAL if the engine speed is higher than
idle speed. If your foot is not firmly pressing the
brake pedal, the vehicle could accelerate quickly
forward or in reverse. You could lose control of the
vehicle and hit someone or something. Only shift
into gear when the engine is idling normally and
when your foot is firmly pressing the brake pedal.
Key Ignition Park Interlock
This vehicle is equipped with a Key Ignition Park Interlock which requires the shift lever to be placed in PARK
before the ignition switch can be turned to the LOCK/
OFF position. The key fob can only be removed from the
ignition when the ignition is in the LOCK/OFF position
and once removed the shift lever is locked in PARK.
Brake/Transmission Shift Interlock System
This vehicle is equipped with a Brake Transmission Shift
Interlock (BTSI) that holds the shift lever in the PARK
position unless the brakes are applied. To move the shift
lever out of the PARK position, the ignition switch must
be turned to the ON/RUN or START position (engine
running or not) and the brake pedal must be pressed.
Five-Speed Automatic Transmission (3.6L Engine)
— If Equipped
The shift lever position display (located in the instrument
panel cluster) indicates the transmission gear range. You
must press the brake pedal to move the shift lever out of
the PARK position (refer to “Brake/Transmission Shift
Interlock System” in this section). To drive, move the shift
lever from PARK or NEUTRAL to the DRIVE position.
STARTING AND OPERATING 433
The electronically-controlled transmission provides a
precise shift schedule. The transmission electronics are
self-calibrating; therefore, the first few shifts on a new
vehicle may be somewhat abrupt. This is a normal
condition, and precision shifts will develop within a few
hundred miles (kilometers).
Shifting from DRIVE to PARK or REVERSE should be
done only after the accelerator pedal is released and the
vehicle is stopped. Be sure to keep your foot on the brake
pedal when moving the shift lever between these gears.
The transmission shift lever has only PARK, REVERSE,
Shift Lever
NEUTRAL, and DRIVE shift positions. Manual downshifts can be made using the Electronic Range Select Gear Ranges
(ERS) shift control (refer to “Electronic Range Select DO NOT race the engine when shifting from PARK or
(ERS)” in this section). Moving the shift lever to the left or NEUTRAL into another gear range.
right (-/+) while in the DRIVE position will select the
highest available transmission gear, and will display that
gear in the instrument cluster as 4, 3, 2, 1.
5
434 STARTING AND OPERATING
PARK
This range supplements the parking brake by locking the
transmission. The engine can be started in this range.
Never attempt to use PARK while vehicle is in motion.
Apply the parking brake when leaving vehicle in this
range.
When parking on a level surface, you may place the shift
lever in the PARK position first, and then apply the
parking brake.
When parking on a hill, apply the parking brake before
placing the shift lever in PARK, otherwise the load on the
transmission locking mechanism may make it difficult to
move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill
grade and away from the curb on an uphill grade.
WARNING!
• Never use the PARK position as a substitute for
the parking brake. Always apply the parking
brake fully when parked to guard against vehicle
movement and possible injury or damage.
• Your vehicle could move and injure you and others
if it is not completely in PARK. Check by trying to
move the shift lever rearward (with the brake
pedal released), after you have placed it in PARK.
Make sure the transmission is in PARK before
leaving the vehicle.
(Continued)
STARTING AND OPERATING 435
WARNING! (Continued)
WARNING! (Continued)
• It is dangerous to move the shift lever out of PARK
or NEUTRAL if the engine speed is higher than
idle speed. If your foot is not firmly pressing the
brake pedal, the vehicle could accelerate quickly
forward or in reverse. You could lose control of the
vehicle and hit someone or something. Only shift
into gear when the engine is idling normally and
when your foot is firmly pressing the brake pedal.
• Unintended movement of a vehicle could injure
those in or near the vehicle. As with all vehicles, you
should never exit a vehicle while the engine is
running. Before exiting a vehicle, always apply the
parking brake, shift the transmission into PARK, and
remove the key fob. Once the key fob is removed, the
shift lever is locked in the PARK position, securing
the vehicle against unwanted movement.
• When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children
to be in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Children should be
warned not to touch the parking brake, brake
pedal or the shift lever.
• Do not leave the key fob in or near the vehicle, and
do not leave Keyless Enter-N-Go in the ACC or
ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
(Continued)
5
436 STARTING AND OPERATING
CAUTION!
• Before moving the shift lever out of PARK, you
must turn the ignition switch from the LOCK/OFF
position to the ON/RUN position, and also press
the brake pedal. Otherwise, damage to the shift
lever could result.
• DO NOT race the engine when shifting from
PARK or NEUTRAL into another gear range, as
this can damage the drivetrain.
• Look at the shift lever position display and verify that
it indicates the PARK position.
• With brake pedal released, verify that the shift lever
will not move out of PARK.
REVERSE
This range is for moving the vehicle backward. Shift into
REVERSE only after the vehicle has come to a complete
stop.
NEUTRAL
Use this range when the vehicle is standing for prolonged
The following indicators should be used to ensure that periods with engine running. The engine may be started
you have engaged the shift lever into the PARK position: in this range. Set the parking brake and shift the trans• When shifting into PARK, move the shift lever all the mission into PARK if you must leave the vehicle.
way forward and to the left until it stops and is fully
seated.
STARTING AND OPERATING 437
WARNING!
Do not coast in NEUTRAL and never turn off the
ignition to coast down a hill. These are unsafe
practices that limit your response to changing traffic
or road conditions. You might lose control of the
vehicle and have a collision.
CAUTION!
Towing the vehicle, coasting, or driving for any other
reason with the transmission in NEUTRAL can result
in severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and
“Towing A Disabled Vehicle” in “What To Do In
Emergencies” for further information.
DRIVE
This range should be used for most city and highway
driving. It provides the smoothest upshifts and downshifts, and the best fuel economy. The transmission
automatically upshifts through underdrive first, second,
and third gears, direct fourth gear and overdrive fifth
gear. The DRIVE position provides optimum driving
characteristics under all normal operating conditions.
When frequent transmission shifting occurs (such as
when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or
while towing heavy trailers), use the Electronic Range
Select (ERS) feature (refer to “Electronic Range Select
(ERS)” in this section) to select a lower gear range. Under
these conditions, using a lower gear range will improve
performance and extend transmission life by reducing
excessive shifting and heat buildup.
5
438 STARTING AND OPERATING
Transmission Limp Home Mode
Transmission function is monitored electronically for
abnormal conditions. If a condition is detected that could
result in transmission damage, Transmission Limp Home
Mode is activated. In this mode, the transmission remains
in the current gear until the vehicle is brought to a stop.
After the vehicle has stopped, the transmission will
remain in second gear regardless of which forward gear
is selected. PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL)
may be illuminated. Limp Home Mode allows the vehicle
to be driven to an authorized dealer for service without
damaging the transmission.
3. Turn the ignition switch to the LOCK/OFF position.
4. Wait approximately 10 seconds.
5. Restart the engine.
6. Shift into the desired gear range. If the problem is no
longer detected, the transmission will return to normal
operation.
NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your
earliest possible convenience. Your authorized dealer has
diagnostic equipment to determine if the problem could
recur.
In the event of a momentary problem, the transmission If the transmission cannot be reset, authorized dealer
can be reset to regain all forward gears by performing the service is required.
following steps:
1. Stop the vehicle.
2. Shift the transmission into PARK.
STARTING AND OPERATING 439
To exit ERS mode, simply press and hold the shift lever to
Electronic Range Select (ERS) Operation
The Electronic Range Select (ERS) shift control allows the the right (+) until “D” is once again displayed in the shift
driver to limit the highest available gear when the shift lever position indicator in the instrument cluster.
lever is in the DRIVE position. For example, if you shift
WARNING!
the transmission into 3 (third gear), the transmission will
never shift above third gear, but will shift down into
Do not downshift for additional engine braking on a
second and first gear normally.
slippery surface. The drive wheels could lose their
You can switch between DRIVE and ERS mode at any grip and the vehicle could skid, causing an accident
vehicle speed. When the shift lever is in the DRIVE or personal injury.
position, the transmission will operate automatically,
shifting between all available gears. Tapping the shift Screen Display
1
2
3
4
D
lever to the left (-) will downshift the transmission,
Actual Gear(s) Allowed
1 1-2 1-3 1-4 1-5
activate ERS mode, display the current gear in the
instrument cluster, and maintain that gear as the top NOTE: To select the proper gear position for maximum
available gear. Once in ERS mode, tapping the shift lever deceleration (engine braking), simply press and hold the
to the left (-) or right (+) will change the top available shift lever to the left (-). The transmission will shift to the
range from which the vehicle can best be slowed down.
gear.
5
440 STARTING AND OPERATING
Overdrive Operation
The automatic transmission includes an electronically
controlled Overdrive (fifth gear). The transmission will
automatically shift into the Overdrive gear if the following conditions are present:
• the shift lever is in the DRIVE position,
• vehicle speed is sufficiently high, and
• the driver is not heavily pressing the accelerator.
Six-Speed Automatic Transmission (5.7L Engine)
— If Equipped
The shift lever position display (located in the instrument
panel cluster) indicates the transmission gear range. You
must press the brake pedal to move the shift lever out of
the PARK position (refer to “Brake/Transmission Shift
Interlock System” in this section). To drive, move the shift
lever from PARK or NEUTRAL to the DRIVE position.
The electronically-controlled transmission provides a
precise shift schedule. The transmission electronics are
self-calibrating; therefore, the first few shifts on a new
vehicle may be somewhat abrupt. This is a normal
condition, and precision shifts will develop within a few
hundred miles (kilometers).
Shifting from DRIVE to PARK or REVERSE should be
done only after the accelerator pedal is released and the
vehicle is stopped. Be sure to keep your foot on the brake
pedal when moving the shift lever between these gears.
The transmission shift lever has only PARK, REVERSE,
NEUTRAL, and DRIVE shift positions. Manual downshifts can be made using the Electronic Range Select
(ERS) shift control (refer to “Electronic Range Select
(ERS)” in this section). Moving the shift lever to the left or
right (-/+) while in the DRIVE position will select the
highest available transmission gear, and will display that
gear in the instrument cluster as 6, 5, 4, 3, 2, 1.
STARTING AND OPERATING 441
PARK
This range supplements the parking brake by locking the
transmission. The engine can be started in this range.
Never attempt to use PARK while vehicle is in motion.
Apply the parking brake when leaving vehicle in this
range.
When parking on a level surface, you may place the shift
lever in the PARK position first, and then apply the
parking brake.
When parking on a hill, apply the parking brake before
placing the shift lever in PARK, otherwise the load on the
Shift Lever
transmission locking mechanism may make it difficult to
Gear Ranges
move the shift lever out of PARK. As an added precauDO NOT race the engine when shifting from PARK or tion, turn the front wheels toward the curb on a downhill
NEUTRAL into another gear range.
grade and away from the curb on an uphill grade.
5
442 STARTING AND OPERATING
WARNING!
WARNING! (Continued)
• Never use the PARK position as a substitute for
the parking brake. Always apply the parking
brake fully when parked to guard against vehicle
movement and possible injury or damage.
• Your vehicle could move and injure you and others
if it is not completely in PARK. Check by trying to
move the shift lever rearward (with the brake
pedal released), after you have placed it in PARK.
Make sure the transmission is in PARK before
leaving the vehicle.
• It is dangerous to move the shift lever out of PARK
or NEUTRAL if the engine speed is higher than
idle speed. If your foot is not firmly pressing the
brake pedal, the vehicle could accelerate quickly
forward or in reverse. You could lose control of the
vehicle and hit someone or something. Only shift
into gear when the engine is idling normally and
when your foot is firmly pressing the brake pedal.
• Unintended movement of a vehicle could injure
those in or near the vehicle. As with all vehicles, you
should never exit a vehicle while the engine is
running. Before exiting a vehicle, always apply the
parking brake, shift the transmission into PARK, and
remove the key fob. Once the key fob is removed, the
shift lever is locked in the PARK position, securing
the vehicle against unwanted movement.
(Continued)
(Continued)
STARTING AND OPERATING 443
WARNING! (Continued)
CAUTION!
• When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children
to be in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Children should be
warned not to touch the parking brake, brake
pedal or the shift lever.
• Do not leave the key fob in or near the vehicle, and
do not leave Keyless Enter-N-Go in the ACC or
ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
• Before moving the shift lever out of PARK, you
must turn the ignition switch from the LOCK/OFF
position to the ON/RUN position, and also press
the brake pedal. Otherwise, damage to the shift
lever could result.
• DO NOT race the engine when shifting from
PARK or NEUTRAL into another gear range, as
this can damage the drivetrain.
The following indicators should be used to ensure that
you have engaged the shift lever into the PARK position:
• When shifting into PARK, move the shift lever all the
way forward and to the left until it stops and is fully
seated.
• Look at the shift lever position display and verify that
it indicates the PARK position.
5
444 STARTING AND OPERATING
• With brake pedal released, verify that the shift lever
will not move out of PARK.
REVERSE
This range is for moving the vehicle backward. Shift into
REVERSE only after the vehicle has come to a complete
stop.
CAUTION!
Towing the vehicle, coasting, or driving for any other
reason with the transmission in NEUTRAL can result
in severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and
“Towing A Disabled Vehicle” in “What To Do In
Emergencies” for further information.
NEUTRAL
Use this range when the vehicle is standing for prolonged
periods with engine running. The engine may be started DRIVE
in this range. Set the parking brake and shift the trans- This range should be used for most city and highway
mission into PARK if you must leave the vehicle.
driving. It provides the smoothest upshifts and downshifts, and the best fuel economy. The transmission
WARNING!
automatically upshifts through underdrive first and secDo not coast in NEUTRAL and never turn off the ond gears, direct third gear and overdrive fourth and
fifth gears. The DRIVE position provides optimum drivignition to coast down a hill. These are unsafe
practices that limit your response to changing traffic ing characteristics under all normal operating conditions.
or road conditions. You might lose control of the
vehicle and have a collision.
STARTING AND OPERATING 445
To access all six available gears, you must use the If the transmission becomes extremely hot, the “TransElectronic Range Select (ERS) feature (refer to “Electronic mission Temperature Warning Light” may illuminate and
the transmission may downshift out of Overdrive until
Range Select (ERS)” in this section).
the transmission cools down.
When frequent transmission shifting occurs (such as
when operating the vehicle under heavy loading condi- NOTE: Use caution when operating a heavily loaded
tions, in hilly terrain, traveling into strong head winds, or vehicle at low speeds (such as towing a trailer up a steep
while towing heavy trailers), use the Electronic Range grade, or in stop-and-go traffic) during hot weather. In
Select (ERS) feature (refer to “Electronic Range Select these conditions, torque converter slip can impose a
(ERS)” in this section) to select a lower gear range. Under significant additional heat load on the cooling system.
these conditions, using a lower gear range will improve Downshifting the transmission to the lowest possible
performance and extend transmission life by reducing gear (when climbing a grade), or shifting to NEUTRAL
(when stopped in heavy traffic) can help to reduce this
excessive shifting and heat buildup.
excess heat generation.
If the transmission operating temperature exceeds normal operating limits, the powertrain controller will During cold temperatures, transmission operation may
modify the transmission shift schedule and expand the be modified depending on engine and transmission
range of torque converter clutch engagement. This is temperature as well as vehicle speed. This feature imdone to prevent transmission damage due to overheat- proves warm up time of the engine and transmission to
achieve maximum efficiency. Engagement of both the
ing.
5
446 STARTING AND OPERATING
torque converter clutch and the top overdrive gear are
inhibited until the transmission fluid is warm (refer to the
“Note” under “Torque Converter Clutch” in this section).
During extremely cold temperatures (-16°F [-27°C] or
below), operation may briefly be limited to first and
direct gears only. Normal operation will resume once the
transmission temperature has risen to a suitable level.
Transmission Limp Home Mode
Transmission function is monitored electronically for
abnormal conditions. If a condition is detected that could
result in transmission damage, Transmission Limp Home
Mode is activated. In this mode, the transmission remains
in third gear regardless of which forward gear is selected.
PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL) may be illuminated. Limp Home Mode allows the vehicle to be
driven to an authorized dealer for service without damaging the transmission.
In the event of a momentary problem, the transmission
can be reset to regain all forward gears by performing the
following steps:
1. Stop the vehicle.
2. Shift the transmission into PARK.
3. Turn the ignition switch to the LOCK/OFF position.
4. Wait approximately 10 seconds.
5. Restart the engine.
6. Shift into the desired gear range. If the problem is no
longer detected, the transmission will return to normal
operation.
NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your
earliest possible convenience. Your authorized dealer has
diagnostic equipment to determine if the problem could
recur.
STARTING AND OPERATING 447
If the transmission cannot be reset, authorized dealer You can switch between DRIVE and ERS mode at any
vehicle speed. When the shift lever is in the DRIVE
service is required.
position, the transmission will operate automatically,
Electronic Range Select (ERS) Operation
shifting between all available gears. Tapping the shift
The Electronic Range Select (ERS) shift control allows the
lever to the left (-) will activate ERS mode, display the
driver to limit the highest available gear when the shift
current gear in the instrument cluster, and maintain that
lever is in the DRIVE position. For example, if you shift
gear as the top available gear. Once in ERS mode, tapping
the transmission into 3 (third gear), the transmission will
the shift lever to the left (-) or right (+) will change the top
never shift above third gear, but will shift down into
available gear.
second and first gear normally.
To exit ERS mode, simply press and hold the shift lever to
Use of ERS (or TOW/HAUL mode) also enables an
the right (+) until “D” is once again displayed in the shift
additional underdrive gear which is not normally used
lever position indicator in the instrument cluster.
during through-gear accelerations. This additional gear
can improve vehicle performance and cooling capability
WARNING!
when towing a trailer on certain grades. In ERS mode,
gears 1 though 3 are underdrive gears, and ERS 4 is direct Do not downshift for additional engine braking on a
drive. ERS 5 and 6 (Overdrive gears ) are the same as the slippery surface. The drive wheels could lose their
normal fourth and fifth gears.
grip and the vehicle could skid, causing an accident
or personal injury.
5
448 STARTING AND OPERATING
Screen Display
Actual Gear(s)
Allowed
1
1
2
1-2
3
1-3
4
5
6
D
1,2, 1,2, 1,2, 1-5
4 4,5 4-6
• vehicle speed is sufficiently high,
• the driver is not heavily pressing the accelerator, and
• the TOW/HAUL switch has not been activated.
NOTE: To select the proper gear position for maximum
deceleration (engine braking), simply press and hold the When To Use TOW/HAUL Mode
shift lever to the left (-). The transmission will shift to the When driving in hilly areas, towing a trailer, carrying a
range from which the vehicle can best be slowed down. heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to select TOW/
Overdrive Operation
HAUL mode. This will improve performance and reduce
The automatic transmission includes an electronically the potential for transmission overheating or failure due
controlled Overdrive (fourth and fifth gears). The trans- to excessive shifting. When operating in TOW/HAUL
mission will automatically shift into the Overdrive gear if mode, transmission upshifts are delayed, and the transthe following conditions are present:
mission will automatically downshift (for engine braking) during steady braking maneuvers.
• the shift lever is in the DRIVE position,
• the transmission fluid has reached an adequate temperature,
• the engine coolant has reached an adequate temperature,
STARTING AND OPERATING 449
Torque Converter Clutch
A feature designed to improve fuel economy has been
included in the automatic transmission on your vehicle.
A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly
different feeling or response during normal operation in
the upper gears. When the vehicle speed drops or during
some accelerations, the clutch automatically disengages.
TOW/HAUL Switch
The “TOW/HAUL Indicator Light” will illuminate in the
instrument cluster to indicate that TOW/HAUL mode
has been activated. Pressing the switch a second time
restores normal operation. If the TOW/HAUL mode is
desired, the switch must be pressed each time the engine
is started.
NOTE:
• The torque converter clutch will not engage, and the
transmission will not shift into the top overdrive gear,
until the transmission fluid and engine coolant are
warm [usually after 1 to 3 miles (1.6 to 4.8 km) of
driving]. Because top gear is disabled, and engine
speed is higher when the torque converter clutch is not
engaged, it may seem as if the transmission is not
shifting properly when cold. This is normal. Using the
5
450 STARTING AND OPERATING
Electronic Range Select (ERS) feature, when the trans- ABS and Traction Control, provides resistance to any
mission is sufficiently warm, will demonstrate that the wheel that is slipping to allow additional torque transfer
transmission is able to shift into and out of Overdrive. to wheels with traction.
• If the vehicle has not been driven for several days, the
first few seconds of operation after shifting the transmission into gear may seem sluggish. This is due to the
fluid partially draining from the torque converter into
the transmission. This condition is normal and will not
cause damage to the transmission. The torque converter will refill within five seconds after starting the
engine.
ALL-WHEEL DRIVE OPERATION
Single-Speed Operating Instructions/Precautions
(3.6L Engine) – If Equipped
This system contains a single-speed (HI range only)
transfer case, which provides convenient full-time allwheel drive. No driver interaction is required. The Brake
Traction Control (BTC) System, which combines standard
NOTE: This system is not appropriate for conditions
where LOW range is recommended. Refer to “Off-Road
Driving Tips” in “Starting and Operating” for further
information.
Electronically Shifted Transfer Case
(Three-Position Switch) (5.7L Engine) – If
Equipped
This is an electronic shift transfer case and it is operated
by the AWD Control Switch, which is located on the
center console.
STARTING AND OPERATING 451
This electronically shifted transfer case is designed to be
driven in the AWD AUTO position for normal street and
highway conditions on dry hard surfaced roads.
For variable driving conditions, the AWD AUTO mode
can be used. In this mode, the front axle is engaged, but
the vehicle’s power is sent to the rear wheels. All-wheel
drive will be automatically engaged when the vehicle
senses a loss of traction.
When additional traction is required, the transfer case
LOW RANGE position can be used to lock the front and
rear driveshafts together forcing the front and rear wheels
AWD Control Switch (Three–Position)
to rotate at the same speed. This is accomplished by
This electronically shifted transfer case provides three rotating the AWD Control Switch to the desired position.
mode positions:
Refer to “Shifting Procedure” for specific shifting instructions. The LOW RANGE position is designed for loose,
• All-wheel drive automatic range (AWD AUTO)
slippery road surfaces only. Driving in the LOW RANGE
• All-wheel drive low range (LOW RANGE)
position on dry hard surfaced roads may cause increased
tire wear and damage to the driveline components.
• Neutral (NEUTRAL)
5
452 STARTING AND OPERATING
Transfer Case Position Indicator Messages
The Transfer Case Position Indicator messages (AWD
AUTO and LOW RANGE) are located in the EVIC
(Electronic Vehicle Information Center) and indicate the
current and desired transfer case selection. Refer to
“Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When you select a different transfer case position,
the position indicator lights will do the following:
If One Or More Shift Conditions Are Not Met:
1. The indicator light for the current position will remain
ON.
2. The newly selected position indicator light will continue to flash.
3. The transfer case will not shift.
NOTE: Before retrying a selection, make certain that all
the necessary requirements for selecting a new transfer
If All Shift Conditions Are Met:
case position have been met. To retry the selection, turn
1. The current position indicator light will turn OFF.
the control knob back to the current position, wait five
seconds, and retry selection. To find the shift require2. The selected position indicator light will flash until the
ments, refer to the ⬙Shifting Procedure⬙ for your transfer
transfer case completes the shift.
case, located in this section of the owner’s manual.
3. When the shift is complete, the indicator light for the
The “SERV AWD Warning Light” monitors the electronic
selected position will stop flashing and remain ON.
shift all-wheel drive system. If this light remains on after
STARTING AND OPERATING 453
engine start up or illuminates during driving, it means Proper operation of all-wheel drive vehicles depends on
that the all-wheel drive system is not functioning prop- tires of equal size, type and circumference on each wheel.
erly and that service is required.
Any difference in tire size can cause damage to the
transfer case.
WARNING!
Always engage the parking brake when powering
down the vehicle if the “SERV AWD Warning Light”
is illuminated. Not engaging the parking brake may
allow the vehicle to roll which may cause personal
injury.
NOTE: Do not attempt to make a shift while only the
front or rear wheels are spinning. This could cause
damage to driveline components.
When operating your vehicle in LOW RANGE, the engine
speed is approximately three times that of the AWD AUTO
position at a given road speed. Take care not to overspeed
the engine and do not exceed 25 mph (40 km/h).
Because all-wheel drive provides improved traction,
there is a tendency to exceed safe turning and stopping
speeds. Do not go faster than road conditions permit.
WARNING!
You or others could be injured if you leave the
vehicle unattended with the transfer case in the
NEUTRAL position without first fully engaging the
parking brake. The transfer case NEUTRAL position
disengages both the front and rear driveshafts from
the powertrain and will allow the vehicle to move
regardless of the transmission position. The parking
brake should always be applied when the driver is
not in the vehicle.
5
454 STARTING AND OPERATING
For additional information on the appropriate use of each towing behind another vehicle. Refer to “Recreational
transfer case mode position, see the information below: Towing” in “Starting and Operating” for further
information.
AWD AUTO
All-Wheel Drive Auto Range - This range sends power to Shifting Procedure
the rear wheels. The all–wheel drive system will be
NOTE:
automatically engaged when the vehicle senses a loss of
• If any of the requirements to select a new transfer case
traction. Additional traction for varying road conditions.
position have not been met, the transfer case will not
shift. The position indicator light for the previous
LOW RANGE
position will remain ON, and the newly selected
All-Wheel Drive Low Range - This range provides low
position indicator light will continue to flash until all
speed all-wheel drive. Locks the front and rear drivethe requirements for the selected position have been
shafts together forcing the front and rear wheels to rotate
met. To retry a shift: return the control knob back to the
at the same speed. Additional traction and maximum
original position, make certain all shift requirements
pulling power for loose, slippery road surfaces only. Do
have been met, wait five seconds and try the shift
not exceed 25 mph (40 km/h).
again.
N
Neutral - This range disengages both the front and rear • If all the requirements to select a new transfer case
position have been met, the current position indicator
driveshafts from the powertrain. To be used for flat
light will turn OFF, the selected position indicator light
STARTING AND OPERATING 455
will flash until the transfer case completes the shift. 3. While still rolling, rotate the AWD control switch to
When the shift is complete, the position indicator light the desired position.
for the selected position will stop flashing and remain
4. After the desired position indicator light is ON (not
ON.
flashing), shift the transmission back into gear.
AWD AUTO⇔LOW RANGE
Alternate Procedure
NOTE: When shifting into or out of LOW RANGE some
1. Bring the vehicle to complete stop.
gear noise may be heard. This noise is normal and is not
detrimental to the vehicle or occupants.
2. With the ignition switch in the ON position and the
engine either OFF or running, shift the transmission into
Shifting can be performed with the vehicle rolling 2 to
NEUTRAL.
3 mph (3 to 5 km/h) or completely stopped. Use either of
the following procedures:
3. Rotate the AWD control switch to the desired position.
Preferred Procedure
4. After the desired position indicator light is ON (not
flashing), shift the transmission back into gear.
1. With the engine running, slow the vehicle to 2 to
3 mph (3 to 5 km/h).
NOTE: If Steps 1 or 2 of either the Preferred or Alternate
Procedure are not satisfied prior to attempting the shift or
2. Shift the transmission into NEUTRAL.
if they no longer are being met while the shift attempt is
in process, the desired position indicator light will flash
5
456 STARTING AND OPERATING
continuously while the original position indicator light is
ON, until all requirements have been met.
NOTE: The ignition switch must be in the ON position
for a shift to take place and for the position indicator
lights to be operable. If the ignition switch is not in the
ON position, then the shift will not take place and no
position indicator lights will be on or flashing.
NEUTRAL Shift Procedure
1. Turn the ignition switch to the ON position, engine off.
2. Vehicle stopped, with foot on brake.
3. Place the transmission into NEUTRAL.
4. Hold down the NEUTRAL “pin” switch (with a pen,
etc.) for four seconds until the LED light by the switch
starts to blink indicating shift in progress. The light will
stop blinking (stay on solid) when the NEUTRAL shift is
complete.
Neutral Switch
5. Repeat Steps 1 to 4 to shift out of NEUTRAL.
NOTE: If shift conditions/interlocks are not met, a “To
Tow Vehicle Safely, Read Neutral Shift Procedure in
Owners Manual” message will flash from the Electronic
Vehicle Information Center (EVIC). Refer to “Electronic
STARTING AND OPERATING 457
Vehicle Information Center (EVIC)” in “Understanding OFF-ROAD DRIVING TIPS
Your Instrument Panel” for further information.
When To Use LOW Range – If Equipped
When off-road driving, shift to LOW for additional
ON-ROAD DRIVING TIPS
Utility vehicles have higher ground clearance and a traction. This range should be limited to extreme situanarrower track to make them capable of performing in a tions such as deep snow, mud, or sand where additional
wide variety of off-road applications. Specific design low speed pulling power is needed. Vehicle speeds in
characteristics give them a higher center of gravity than excess of 25 mph (40 km/h) should be avoided when in
LOW range.
ordinary cars.
An advantage of the higher ground clearance is a better
view of the road, allowing you to anticipate problems.
They are not designed for cornering at the same speeds as
conventional two-wheel drive vehicles any more than
low-slung sports cars are designed to perform satisfactorily in off-road conditions. If at all possible, avoid sharp
turns or abrupt maneuvers. As with other vehicles of this
type, failure to operate this vehicle correctly may result in
loss of control or vehicle rollover.
Driving Through Water
Although your vehicle is capable of driving through
water, there are a number of precautions that must be
considered before entering the water.
5
458 STARTING AND OPERATING
CAUTION!
When driving through water, do not exceed 5 mph
(8 km/h). Always check water depth before entering,
as a precaution, and check all fluids afterward. Driving through water may cause damage that may not be
covered by the new vehicle limited warranty.
and/or the flow rate is reduced. If you must cross
flowing water avoid depths in excess of 9 in (23 cm). The
flowing water can erode the streambed, causing your
vehicle to sink into deeper water. Determine exit point(s)
that are downstream of your entry point to allow for
drifting.
Standing Water
Avoid driving in standing water deeper than 20 in
Driving through water more than a few inches/
(51 cm), and reduce speed appropriately to minimize
centimeters deep will require extra caution to ensure
wave effects. Maximum speed in 20 in (51 cm) of water is
safety and prevent damage to your vehicle. If you must
less than 5 mph (8 km/h).
drive through water, try to determine the depth and the
bottom condition (and location of any obstacles) prior to Maintenance
entering. Proceed with caution and maintain a steady After driving through deep water, inspect your vehicle
controlled speed less than 5 mph (8 km/h) in deep water fluids and lubricants (engine oil, transmission oil, axle,
transfer case) to assure the fluids have not been contamito minimize wave effects.
nated. Contaminated fluid (milky, foamy in appearance)
Flowing Water
should be flushed/changed as soon as possible to preIf the water is swift flowing and rising (as in storm
vent component damage.
run-off), avoid crossing until the water level recedes
STARTING AND OPERATING 459
Driving In Snow, Mud And Sand
In heavy snow, when pulling a load, or for additional
control at slower speeds, shift the transmission to a low
gear and shift the transfer case to LOW if necessary. Refer
to “All-Wheel Drive Operation” in “Starting and Operating” for further information. Do not shift to a lower gear
than necessary to maintain forward motion. Over-revving
the engine can spin the wheels and traction will be lost.
Avoid abrupt downshifts on icy or slippery roads, because engine braking may cause skidding and loss of
control.
Hill Climbing
NOTE: Before attempting to climb a hill, determine the
conditions at the crest and/or on the other side.
Before climbing a steep hill, shift the transmission to a
lower gear and shift the transfer case to LOW. Use first
gear and LOW for very steep hills.
If you stall or begin to lose forward motion while
climbing a steep hill, allow your vehicle to come to a stop
and immediately apply the brakes. Restart the engine,
and shift into REVERSE. Back slowly down the hill,
allowing the compression braking of the engine to help
regulate your speed. If the brakes are required to control
vehicle speed, apply them lightly and avoid locking or
skidding the tires.
WARNING!
If the engine stalls, you lose forward motion, or
cannot make it to the top of a steep hill or grade,
never attempt to turn around. To do so may result in
tipping and rolling the vehicle. Always back carefully straight down a hill in REVERSE gear. Never
back down a hill in NEUTRAL using only the brake.
5
460 STARTING AND OPERATING
Remember, never drive diagonally across a hill always After Driving Off-Road
Off-road operation puts more stress on your vehicle than
drive straight up or down.
does most on-road driving. After going off-road, it is
If the wheels start to slip as you approach the crest of a
always a good idea to check for damage. That way you
hill, ease off the accelerator and maintain forward motion
can get any problems taken care of right away and have
by turning the front wheels slowly. This may provide a
your vehicle ready when you need it.
fresh “bite” into the surface and will usually provide
• Completely inspect the underbody of your vehicle.
traction to complete the climb.
Check tires, body structure, steering, suspension, and
Traction Downhill
exhaust system for damage.
Shift the transmission into a low gear, and the transfer
case into LOW range. Let the vehicle go slowly down the • Inspect the radiator for mud and debris and clean as
hill with all four wheels turning against engine compresrequired.
sion drag. This will permit you to control the vehicle
• Check threaded fasteners for looseness, particularly on
speed and direction.
the chassis, drivetrain components, steering, and suspension. Retighten them, if required, and torque to the
When descending mountains or hills, repeated braking
values specified in the Service Manual.
can cause brake fade with loss of braking control. Avoid
repeated heavy braking by downshifting the transmission whenever possible.
STARTING AND OPERATING 461
• Check for accumulations of plants or brush. These • If you experience unusual vibration after driving in
things could be a fire hazard. They might hide damage
mud, slush or similar conditions, check the wheels for
to fuel lines, brake hoses, axle pinion seals, and
impacted material. Impacted material can cause a
propeller shafts.
wheel imbalance and freeing the wheels of it will
correct the situation.
• After extended operation in mud, sand, water, or
similar dirty conditions, have the radiator, fan, brake POWER STEERING
rotors, wheels, brake linings, and axle yokes inspected
3.6L Engine
and cleaned as soon as possible.
Your vehicle is equipped with an electro-hydraulic power
steering system that will give you good vehicle response
WARNING!
and increased ease of maneuverability in tight spaces.
Abrasive material in any part of the brakes may cause The system will vary its assist to provide light efforts
excessive wear or unpredictable braking. You might while parking and good feel while driving. If the electronot have full braking power when you need it to hydraulic power steering system experiences a fault that
prevent a collision. If you have been operating your prevents it from providing power steering assist, then the
vehicle in dirty conditions, get your brakes checked system will provide mechanical steering capability.
and cleaned as necessary.
5
462 STARTING AND OPERATING
CAUTION!
Extreme steering maneuvers may cause the electrically driven pump to reduce or stop power steering
assistance in order to prevent damage to the system.
Normal operation will resume once the system is
allowed to cool.
occurred, which caused an over temperature condition in
the power steering system. You will lose power steering
assistance momentarily until the over temperature condition no longer exists. Once driving conditions are safe,
then pull over and let vehicle idle for a few moments
until the light turns off. Refer to “Electronic Vehicle
Information Center (EVIC)” in “Understanding Your
Instrument Panel” for further information.
If the “SERVICE POWER STEERING SYSTEM”
NOTE:
message and a flashing icon are displayed on
• Even if power steering assistance is no longer operathe EVIC screen, it indicates that the vehicle
tional, it is still possible to steer the vehicle. Under
needs to be taken to the dealer for service. It is
these conditions there will be a substantial increase in
likely the vehicle has lost power steering assistance. Refer
steering effort, especially at very low vehicle speeds
to “Electronic Vehicle Information Center (EVIC)” in
and during parking maneuvers.
“Understanding Your Instrument Panel” for further in• If the condition persists, see your authorized dealer for
formation.
service.
If the “POWER STEERING SYSTEM OVER TEMP” message and an icon are displayed on the EVIC screen, it
indicates that extreme steering maneuvers may have
STARTING AND OPERATING 463
5.7L Engine
• Upon initial start-up in cold weather, the power steerThe standard power steering system will give you good
ing pump may make noise for a short amount of time.
vehicle response and increased ease of maneuverability
This is due to the cold, thick fluid in the steering
in tight spaces. The system will provide mechanical
system. This noise should be considered normal, and it
steering capability if power assist is lost.
does not in any way damage the steering system.
If for some reason the power assist is interrupted, it will
still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering
effort, especially at very low vehicle speeds and during
parking maneuvers.
NOTE:
• Increased noise levels at the end of the steering wheel
travel are considered normal and do not indicate that
there is a problem with the power steering system.
WARNING!
Continued operation with reduced power steering
assist could pose a safety risk to yourself and others.
Service should be obtained as soon as possible.
CAUTION!
Prolonged operation of the steering system at the end
of the steering wheel travel will increase the steering
fluid temperature and it should be avoided when
possible. Damage to the power steering pump may
occur.
5
464 STARTING AND OPERATING
Power Steering Fluid Check
Checking the power steering fluid level at a defined
service interval is not required. The fluid should only be
checked if a leak is suspected, abnormal noises are
apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer.
CAUTION!
Do not use chemical flushes in your power steering
system as the chemicals can damage your power
steering components. Such damage is not covered by
the New Vehicle Limited Warranty.
WARNING!
Fluid level should be checked on a level surface and
with the engine off to prevent injury from moving
parts and to ensure accurate fluid level reading. Do
not overfill. Use only manufacturer’s recommended
power steering fluid.
If necessary, add fluid to restore to the proper indicated
level. With a clean cloth, wipe any spilled fluid from all
surfaces. Refer to “Fluids, Lubricants, and Genuine
Parts” in “Maintaining Your Vehicle” for further
information.
STARTING AND OPERATING 465
MULTI-DISPLACEMENT SYSTEM (MDS)
(IF EQUIPPED) — 5.7L ENGINE ONLY
This feature offers improved fuel economy by shutting
off four of the engine’s eight cylinders during light load
and cruise conditions. The system is automatic with no
driver inputs or additional driving skills required.
NOTE: The MDS system may take some time to return
to full functionality after a battery disconnect.
PARKING BRAKE
Before leaving the vehicle, make sure that the parking
brake is fully applied and place the shift lever in the
PARK position.
5
Parking Brake
When the parking brake is applied with the ignition
The foot operated parking brake is located below the switch in the ON position, the “Brake Warning Light” in
lower left corner of the instrument panel. To apply the the instrument cluster will illuminate.
park brake, firmly push the park brake pedal fully. To
release the parking brake, press the park brake pedal a
second time and let your foot up as you feel the brake
disengage.
466 STARTING AND OPERATING
NOTE:
• When the parking brake is applied and the transmission is placed in gear, the “Brake Warning Light” will
flash. If vehicle speed is detected, a chime will sound
to alert the driver. Fully release the parking brake
before attempting to move the vehicle.
• This light only shows that the parking brake is applied. It does not show the degree of brake application.
When parking on a hill, it is important to turn the front
wheels toward the curb on a downhill grade and away
from the curb on an uphill grade. Apply the parking
brake before placing the shift lever in PARK, otherwise
the load on the transmission locking mechanism may
make it difficult to move the shift lever out of PARK. The
parking brake should always be applied whenever the
driver is not in the vehicle.
WARNING!
• Never use the PARK position as a substitute for
the parking brake. Always apply the parking
brake fully when parked to guard against vehicle
movement and possible injury or damage.
• When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle. Never
leave children alone in a vehicle, or with access to
an unlocked vehicle. Allowing children to be in a
vehicle unattended is dangerous for a number of
reasons. A child or others could be seriously or
fatally injured. Children should be warned not to
touch the parking brake, brake pedal or the shift
lever.
(Continued)
STARTING AND OPERATING 467
WARNING! (Continued)
• Do not leave the key fob in or near the vehicle, and
do not leave Keyless Enter-N-Go in the ACC or
ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
• Be sure the parking brake is fully disengaged
before driving; failure to do so can lead to brake
failure and a collision.
• Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage
or injury. Also be certain to leave the transmission
in PARK. Failure to do so may allow the vehicle to
roll and cause damage or injury.
CAUTION!
If the “Brake Warning Light” remains on with the
parking brake released, a brake system malfunction
is indicated. Have the brake system serviced by an
authorized dealer immediately.
ELECTRONIC BRAKE CONTROL SYSTEM
Your vehicle is equipped with an advanced electronic
brake control system that includes the Anti-Lock Brake
System (ABS), Traction Control System (TCS), Brake
Assist System (BAS), Electronic Roll Mitigation (ERM),
and Electronic Stability Control (ESC). All five of these
systems work together to enhance vehicle stability and
control in various driving conditions.
Also, your vehicle is equipped with Trailer Sway Control
(TSC), Hill Start Assist (HSA), Brake Lock Differential
(BLD), Ready Alert Braking, and Rain Brake Support.
5
468 STARTING AND OPERATING
Anti-Lock Brake System (ABS)
Traction Control System (TCS)
This system aids the driver in maintaining vehicle control
under adverse braking conditions. The system controls
hydraulic brake pressure to prevent wheel lock-up and
help avoid skidding on slippery surfaces during braking.
This system monitors the amount of wheel spin of each of
the driven wheels. If wheel spin is detected, brake
pressure is applied to the slipping wheel(s) and engine
power is reduced to provide enhanced acceleration and
stability. A feature of the TCS system, Brake Limited
Differential (BLD), functions similar to a limited-slip
differential and controls the wheel spin across a driven
axle. If one wheel on a driven axle is spinning faster than
the other, the system will apply the brake of the spinning
wheel. This will allow more engine torque to be applied
to the wheel that is not spinning. This feature remains
active even if ESC system is in the “Partial Off” mode.
Refer to “Electronic Stability Control (ESC)” in this
section for more information.
WARNING!
The ABS cannot prevent the natural laws of physics
from acting on the vehicle, nor can it increase the
traction afforded by prevailing road conditions. The
ABS cannot prevent collisions, including those resulting from excessive speed in turns, driving on
very slippery surfaces, or hydroplaning. The capabilities of an ABS-equipped vehicle must never be
exploited in a reckless or dangerous manner which
could jeopardize the user’s safety or the safety of
others.
STARTING AND OPERATING 469
Brake Assist System (BAS)
The BAS is designed to optimize the vehicle’s braking
capability during emergency braking maneuvers. The
system detects an emergency braking situation by sensing the rate and amount of brake application and then
applies optimum pressure to the brakes. This can help
reduce braking distances. The BAS complements the
anti-lock brake system (ABS). Applying the brakes very
quickly results in the best BAS assistance. To receive the
benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not
“pump” the brakes). Do not reduce brake pedal pressure
unless braking is no longer desired. Once the brake pedal
is released, the BAS is deactivated.
WARNING!
The BAS cannot prevent the natural laws of physics
from acting on the vehicle, nor can it increase the
traction afforded by prevailing road conditions. The
BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on
very slippery surfaces, or hydroplaning. The capabilities of a BAS-equipped vehicle must never be
exploited in a reckless or dangerous manner which
could jeopardize the user’s safety or the safety of
others.
5
470 STARTING AND OPERATING
Electronic Roll Mitigation (ERM)
This system anticipates the potential for wheel lift by
monitoring the driver’s steering wheel input and the
speed of the vehicle. When ERM determines that the rate
of change of the steering wheel angle and vehicle speed
are sufficient to potentially cause wheel lift, it then
applies the brake of the appropriate wheel and may also
reduce engine power to lessen the chance that wheel lift
will occur. ERM will only intervene during very severe or
evasive driving maneuvers.
WARNING!
Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance
that wheel lift or rollover may occur. ERM cannot
prevent all wheel lift or rollovers, especially those
that involve leaving the roadway or striking objects
or other vehicles. The capabilities of an ERMequipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the
user’s safety or the safety of others.
ERM can only reduce the chance of wheel lift occurring
during severe or evasive driving maneuvers. It cannot
Electronic Stability Control (ESC)
prevent wheel lift due to other factors such as road
conditions, leaving the roadway or striking objects or This system enhances directional control and stability of
other vehicles.
the vehicle under various driving conditions. ESC corrects for oversteering or understeering of the vehicle by
applying the brake of the appropriate wheel to assist in
STARTING AND OPERATING 471
counteracting the oversteer or understeer condition. En- flash during acceleration, ease up on the accelerator and
gine power may also be reduced to help the vehicle apply as little throttle as possible. Be sure to adapt your
speed and driving to the prevailing road conditions.
maintain the desired path.
ESC uses sensors in the vehicle to determine the vehicle
path intended by the driver and compares it to the actual
path of the vehicle. When the actual path does not match
the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or
understeer condition.
• Oversteer - when the vehicle is turning more than
appropriate for the steering wheel position.
• Understeer - when the vehicle is turning less than
appropriate for the steering wheel position.
The “ESC Malfunction Indicator Light” located in the
instrument cluster will start to flash as soon as the tires lose
traction and the ESC system becomes active. The “ESC
Malfunction Indicator Light” also flashes when the TCS is
active. If the “ESC Malfunction Indicator Light” begins to
WARNING!
Electronic Stability Control (ESC) cannot prevent the
natural laws of physics from acting on the vehicle, nor
can it increase the traction afforded by prevailing
road conditions. ESC cannot prevent accidents, including those resulting from excessive speed in turns,
driving on very slippery surfaces, or hydroplaning.
ESC also cannot prevent accidents resulting from loss
of vehicle control due to inappropriate driver input
for the conditions. Only a safe, attentive, and skillful
driver can prevent accidents. The capabilities of an
ESC equipped vehicle must never be exploited in a
reckless or dangerous manner which could jeopardize
the user’s safety or the safety of others.
5
472 STARTING AND OPERATING
The ESC system has two available operating modes in Partial Off
AWD AUTO range and two-wheel drive vehicles, and This mode is entered by momentarily pressing the “ESC
OFF” switch. When in “Partial Off” mode, the TCS
one operating mode in AWD LOW range.
portion of ESC, except for the BLD feature described in
AUTO Range (All-Wheel Drive Models) Or
the TCS section, has been disabled and the “ESC Off
Two-Wheel Drive Models
Indicator Light” will be illuminated. The enhanced veOn
hicle stability offered by the ESC system is reduced. This
This is the normal operating mode for ESC in AWD mode is intended to be used if the vehicle is in deep
AUTO range and in two-wheel drive vehicles. Whenever snow, sand, or gravel conditions and more wheel spin
the vehicle is started or the transfer case (if equipped) is than ESC would normally allow is required to gain
shifted from AWD LOW range or NEUTRAL back to traction. To turn ESC on again, momentarily press the
AWD AUTO range, the ESC system will be in this “On” “ESC OFF” switch. This will restore the normal “ESC
mode. This mode should be used for most driving On” mode of operation.
situations. ESC should only be turned to “Partial Off”
mode for specific reasons as noted below.
STARTING AND OPERATING 473
Off” mode is overcome, turn ESC back on by momentarily pressing the “ESC OFF” switch. This may be done
while the vehicle is in motion.
WARNING!
ESC OFF Switch
NOTE: To improve the vehicle’s traction when driving
with snow chains, or starting off in deep snow, sand, or
gravel, it may be desirable to switch to the “Partial Off”
mode by pressing the “ESC OFF” switch. Once the
situation requiring ESC to be switched to the “Partial
• When in “Partial Off” mode, the TCS functionality
of ESC, (except for the limited slip feature described in the TCS section), has been disabled and
the “ESC Off Indicator Light” will be illuminated.
When in “Partial Off” mode, the engine power
reduction feature of TCS is disabled, and the
enhanced vehicle stability offered by the ESC
system is reduced.
• Trailer Sway Control (TSC) is disabled when the
ESC system is in the “Partial Off” mode.
5
474 STARTING AND OPERATING
and Operating” for further information. When TSC is
functioning, the “ESC Malfunction Indicator Light” will
Partial Off
flash, the engine power may be reduced and you may
This is the normal operating mode for ESC in AWD LOW
feel the brakes being applied to individual wheels to
range. Whenever the vehicle is started in AWD LOW
attempt to stop the trailer from swaying. TSC is disabled
range, or the transfer case (if equipped) is shifted from
when the ESC system is in the “Partial Off” mode.
AWD AUTO range or NEUTRAL to AWD LOW range,
the ESC system will be in the “Partial Off” mode.
AWD Low Range (LOW)
WARNING!
Trailer Sway Control (TSC)
TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate
actions to attempt to stop the sway. The system may
reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sway of the trailer. TSC
will become active automatically once an excessively
swaying trailer is recognized. Note that TSC cannot stop
all trailers from swaying. Always use caution when
towing a trailer and follow the trailer tongue weight
recommendations. Refer to “Trailer Towing” in “Starting
• If TSC activates while driving, slow the vehicle
down, stop at the nearest safe location, and adjust
the trailer load to eliminate trailer sway.
• TSC is disabled when the ESC system is in the
“Partial Off” mode.
Hill Start Assist (HSA)
The HSA system is designed to assist the driver when
starting a vehicle from a stop on a hill. HSA will maintain
the level of brake pressure the driver applied for a short
period of time after the driver takes their foot off of the
STARTING AND OPERATING 475
brake pedal. If the driver does not apply the throttle HSA will work in REVERSE and all forward gears when
during this short period of time, the system will release the activation criteria have been met. The system will not
brake pressure and the vehicle will roll down the hill. The activate if the vehicle is placed in NEUTRAL or PARK.
system will release brake pressure in proportion to the
WARNING!
amount of throttle applied as the vehicle starts to move in
the intended direction of travel.
There may be situations on minor hills (i.e., less than
HSA Activation Criteria
8%), with a loaded vehicle, or while pulling a trailer,
The following criteria must be met in order for HSA to when the system will not activate and slight rolling
activate:
may occur. This could cause a collision with another
vehicle or object. Always remember the driver is
• Vehicle must be stopped.
responsible for braking the vehicle.
• Vehicle must be on a 6% (approximate) grade or
greater hill.
• Gear selection matches vehicle uphill direction (i.e.,
vehicle facing uphill is in forward gear; vehicle backing uphill is in REVERSE gear).
5
476 STARTING AND OPERATING
HSA
HSA will provide assistance when starting on a grade
when pulling a trailer.
WARNING!
• If you use a trailer brake controller with your
trailer, your trailer brakes may be activated and
deactivated with the brake switch. If so, when the
brake pedal is released, there may not be enough
brake pressure to hold the vehicle and trailer on a
hill and this could cause a collision with another
vehicle or object behind you. In order to avoid
rolling down the hill while resuming acceleration,
manually activate the trailer brake prior to releasing the brake pedal. Always remember the driver
is responsible for braking the vehicle.
WARNING! (Continued)
• HSA is not a parking brake. Always apply the
parking brake fully when leaving your vehicle.
Also, be certain to leave the transmission in PARK.
Failure to follow these warnings may cause the
vehicle to roll down the incline and could collide
with another vehicle, object or person, and cause
serious or fatal injury. Always remember to use the
parking brake while parking on a hill and that the
driver is responsible for braking the vehicle.
HSA Off
If you wish to turn off the HSA system, it can be done
using the Customer Programmable Features in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)” in “Under(Continued) standing Your Instrument Panel” for further information.
STARTING AND OPERATING 477
Ready Alert Braking
Ready Alert Braking may reduce the time required to
reach full braking during emergency braking situations.
It anticipates when an emergency braking situation may
occur by monitoring how fast the throttle is released by
the driver. When the throttle is released very quickly,
Ready Alert Braking applies a small amount of brake
pressure. This brake pressure will not be noticed by the
driver. The brake system uses this brake pressure to allow
a fast brake response if the driver applies the brakes.
ESC Malfunction Indicator Light And ESC OFF
Indicator Light
The “ESC Malfunction Indicator Light” in the
instrument cluster will come on when the
ignition switch is turned to the ON position. It
should go out with the engine running. If the
“ESC Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been
detected in the ESC system. If this light remains on after
several ignition cycles, and the vehicle has been driven
several miles (kilometers) at speeds greater than 30 mph
Rain Brake Support
(48 km/h), see your authorized dealer as soon as possible
Rain Brake Support may improve braking performance
to have the problem diagnosed and corrected.
in wet conditions. It will periodically apply a small
amount of brake pressure to remove any water buildup
The “ESC OFF Indicator Light” indicates the
on the front brake rotors. It only functions when the
Electronic Stability Control (ESC) is off.
windshield wipers are in the slow or fast mode, it does
not function in the intermittent mode. When Rain Brake
Support is active, there is no notification to the driver and
the driver should not notice it.
5
478 STARTING AND OPERATING
The “ESC Malfunction Indicator Light” (located in the TIRE SAFETY INFORMATION
instrument cluster) starts to flash as soon as the tires lose
Tire Markings
traction and the ESC system becomes active. The “ESC
Malfunction Indicator Light” also flashes when TCS is
active. If the “ESC Malfunction Indicator Light” begins to
flash during acceleration, ease up on the accelerator and
apply as little throttle as possible. Be sure to adapt your
speed and driving to the prevailing road conditions.
NOTE:
• The “ESC Malfunction Indicator Light” and the “ESC
OFF Indicator Light” come on momentarily each time
the ignition switch is turned ON.
• Each time the ignition is turned ON, the ESC system
will be ON even if it was turned off previously.
• The ESC system will make buzzing or clicking sounds
when it is active. This is normal; the sounds will stop
when ESC becomes inactive following the maneuver
that caused the ESC activation.
1 — U.S. DOT Safety
Standards Code (TIN)
2 — Size Designation
3 — Service Description
4 — Maximum Load
5 — Maximum Pressure
6 — Treadwear, Traction and
Temperature Grades
STARTING AND OPERATING 479
NOTE:
• Temporary spare tires are spares designed for tempo• P (Passenger) - Metric tire sizing is based on U.S.
rary emergency use only. Temporary high pressure
design standards. P-Metric tires have the letter “P”
compact spare tires have the letter “T” or “S” molded
molded into the sidewall preceding the size designainto the sidewall preceding the size designation. Extion. Example: P215/65R15 95H.
ample: T145/80D18 103M.
• European-Metric tire sizing is based on European • High flotation tire sizing is based on U.S. design
design standards. Tires designed to this standard have
standards and it begins with the tire diameter molded
the tire size molded into the sidewall beginning with
into the sidewall. Example: 31x10.5 R15 LT.
the section width. The letter ⬙P⬙ is absent from this tire
size designation. Example: 215/65R15 96H.
• LT (Light Truck) - Metric tire sizing is based on U.S.
design standards. The size designation for LT-Metric
tires is the same as for P-Metric tires except for the
letters “LT” that are molded into the sidewall preceding the size designation. Example: LT235/85R16.
5
480 STARTING AND OPERATING
Tire Sizing Chart
EXAMPLE:
Size Designation:
P = Passenger car tire size based on U.S. design standards
ⴖ....blank....ⴖ = Passenger car tire based on European design standards
LT = Light truck tire based on U.S. design standards
T or S = Temporary spare tire
31 = Overall diameter in inches (in)
215 = Section width in millimeters (mm)
65 = Aspect ratio in percent (%)
— Ratio of section height to section width of tire
10.5 = Section width in inches (in)
R = Construction code
— ⬙R⬙ means radial construction
— ⬙D⬙ means diagonal or bias construction
15 = Rim diameter in inches (in)
STARTING AND OPERATING 481
EXAMPLE:
Service Description:
95 = Load Index
— A numerical code associated with the maximum load a tire can carry
H = Speed Symbol
— A symbol indicating the range of speeds at which a tire can carry a load corresponding
to its load index under certain operating conditions
— The maximum speed corresponding to the speed symbol should only be achieved under
specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and
posted speed limits)
Load Identification:
ⴖ....blank....ⴖ = Absence of any text on the sidewall of the tire indicates a Standard Load (SL) tire
Extra Load (XL) = Extra load (or reinforced) tire
Light Load (LL) = Light load tire
C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure
Maximum Load — Maximum load indicates the maximum load this tire is designed to carry
Maximum Pressure — Maximum pressure indicates the maximum permissible cold tire inflation pressure for
this tire
5
482 STARTING AND OPERATING
Tire Identification Number (TIN)
The TIN may be found on one or both sides of the tire,
however, the date code may only be on one side. Tires
with white sidewalls will have the full TIN, including the
date code, located on the white sidewall side of the tire.
Look for the TIN on the outboard side of black sidewall
tires as mounted on the vehicle. If the TIN is not found on
the outboard side, then you will find it on the inboard
side of the tire.
EXAMPLE:
DOT MA L9 ABCD 0301
DOT = Department of Transportation
— This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire
safety standards and is approved for highway use
MA = Code representing the tire manufacturing location (two digits)
L9 = Code representing the tire size (two digits)
ABCD = Code used by the tire manufacturer (one to four digits)
03 = Number representing the week in which the tire was manufactured (two digits)
—03 means the 3rd week.
01 = Number representing the year in which the tire was manufactured (two digits)
—01 means the year 2001
— Prior to July 2000, tire manufacturers were only required to have one number to represent the
year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991
STARTING AND OPERATING 483
Tire Terminology And Definitions
Term
B-Pillar
Cold Tire Inflation Pressure
Maximum Inflation Pressure
Recommended Cold Tire Inflation
Pressure
Tire Placard
Definition
The vehicle B-Pillar is the structural member of the body located
behind the front door.
Cold tire inflation pressure is defined as the tire pressure after the
vehicle has not been driven for at least 3 hours, or driven less
than 1 mile (1.6 km) after sitting for a three hour period. Inflation
pressure is measured in units of PSI (pounds per square inch) or
kPa (kilopascals).
The maximum inflation pressure is the maximum permissible
cold tire inflation pressure for this tire. The maximum inflation
pressure is molded into the sidewall.
Vehicle manufacturer’s recommended cold tire inflation pressure
as shown on the tire placard.
A paper label permanently attached to the vehicle describing the
vehicle’s loading capacity, the original equipment tire sizes and
the recommended cold tire inflation pressures.
5
484 STARTING AND OPERATING
Tire Loading And Tire Pressure
Tire And Loading Information Placard
Tire And Loading Information Placard Location
NOTE: The proper cold tire inflation pressure is listed
on the driver’s side B-Pillar or the rear edge of the
driver’s side door.
Tire and Loading Information Placard
Tire Placard Location
STARTING AND OPERATING 485
This placard tells you important information about
the:
1) number of people that can be carried in the vehicle
2) total weight your vehicle can carry
3) tire size designed for your vehicle
4) cold tire inflation pressures for the front, rear, and
spare tires.
axles must not be exceeded. For further information on
GAWRs, vehicle loading, and trailer towing, refer to
“Vehicle Loading” in this section.
To determine the maximum loading conditions of your
vehicle, locate the statement “The combined weight of
occupants and cargo should never exceed XXX lbs or
XXX kg” on the Tire and Loading Information placard.
The combined weight of occupants, cargo/luggage and
Loading
trailer tongue weight (if applicable) should never exceed
The vehicle maximum load on the tire must not exceed
the weight referenced here.
the load carrying capacity of the tire on your vehicle. You
will not exceed the tire’s load carrying capacity if you Steps For Determining Correct Load Limit
adhere to the loading conditions, tire size, and cold tire
1. Locate the statement “The combined weight of occuinflation pressures specified on the Tire and Loading
pants and cargo should never exceed XXX lbs or XXX kg”
Information placard and in the “Vehicle Loading” section
on your vehicle’s placard.
of this manual.
2. Determine the combined weight of the driver and
NOTE: Under a maximum loaded vehicle condition,
passengers that will be riding in your vehicle.
gross axle weight ratings (GAWRs) for the front and rear
5
486 STARTING AND OPERATING
3. Subtract the combined weight of the driver and pas- NOTE:
• The following table shows examples on how to calcusengers from XXX lbs or XXX kg.
late total load, cargo/luggage, and towing capacities
4. The resulting figure equals the available amount of
of your vehicle with varying seating configurations
cargo and luggage load capacity. For example, if “XXX”
and number and size of occupants. This table is for
amount equals 1,400 lbs (635 kg) and there will be five
illustration purposes only and may not be accurate for
150 lb (68 kg) passengers in your vehicle, the amount of
the seating and load carry capacity of your vehicle.
available cargo and luggage load capacity is 650 lbs
(295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs • For the following example, the combined weight of
occupants and cargo should never exceed 865 lbs
[295 kg]).
(392 kg).
5. Determine the combined weight of luggage and cargo
being loaded on the vehicle. That weight may not safely
exceed the available cargo and luggage load capacity
calculated in Step 4.
6. If your vehicle will be towing a trailer, load from your
trailer will be transferred to your vehicle. Consult this
manual to determine how this reduces the available
cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING 487
5
488 STARTING AND OPERATING
WARNING!
Overloading of your tires is dangerous. Overloading
can cause tire failure, affect vehicle handling, and
increase your stopping distance. Use tires of the
recommended load capacity for your vehicle. Never
overload them.
TIRES — GENERAL INFORMATION
Tire Pressure
Proper tire inflation pressure is essential to the safe and
satisfactory operation of your vehicle. Three primary
areas are affected by improper tire pressure:
Safety
WARNING!
• Improperly inflated tires are dangerous and can
cause collisions.
• Under-inflation increases tire flexing and can result in over-heating and tire failure.
• Over-inflation reduces a tire’s ability to cushion
shock. Objects on the road and chuckholes can
cause damage that result in tire failure.
• Over-inflated or under-inflated tires can affect
vehicle handling and can fail suddenly, resulting
in loss of vehicle control.
• Unequal tire pressures can cause steering problems. You could lose control of your vehicle.
(Continued)
STARTING AND OPERATING 489
WARNING! (Continued)
• Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to
the right or left.
• Always drive with each tire inflated to the recommended cold tire inflation pressure.
Economy
Improper inflation pressures can cause uneven wear
patterns to develop across the tire tread. These abnormal
wear patterns will reduce tread life resulting in a need for
earlier tire replacement. Under-inflation also increases
tire rolling resistance resulting in higher fuel
consumption.
stability of the vehicle and can produce a feeling of
sluggish response or over responsiveness in the steering.
Unequal tire pressures can cause erratic and unpredictable steering response.
Unequal tire pressure from side to side may cause the
vehicle to drift left or right.
Tire Inflation Pressures
The proper cold tire inflation pressure is listed on the
driver’s side “B” Pillar or rear edge of the driver’s side
door.
The pressure should be checked and adjusted, as well as
inspected for signs of tire wear or visible damage, at least
once a month. Use a good quality pocket-type gauge to
check tire pressure. Do not make a visual judgement
Ride Comfort And Vehicle Stability
Proper tire inflation contributes to a comfortable ride. when determining proper inflation. Radial tires may look
Over-inflation produces a jarring and uncomfortable properly inflated even when they are under-inflated.
ride. Both under-inflation and over-inflation affect the
5
490 STARTING AND OPERATING
CAUTION!
After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent
moisture and dirt from entering the valve stem,
which could damage it.
Tire pressures change by approximately 1 psi (7 kPa) per
12°F (7°C) of air temperature change. Keep this in mind
when checking tire pressure inside a garage, especially in
the winter.
Example: If garage temperature = 68°F (20°C) and the
outside temperature = 32°F (0°C) then the cold tire
inflation pressure should be increased by 3 psi (21 kPa),
Inflation pressures specified on the placard are always
which equals 1 psi (7 kPa) for every 12°F (7°C) for this
cold tire inflation pressure. Cold tire inflation pressure is
outside temperature condition.
defined as the tire pressure after the vehicle has not been
driven for at least three hours, or driven less than 1 mile Tire pressure may increase from 2 to 6 psi (13 to 40 kPa)
(1.6 km) after a three-hour period. The cold tire inflation during operation. DO NOT reduce this normal pressure
pressure must not exceed the maximum inflation pres- build-up, or your tire pressure will be too low.
sure molded into the tire sidewall.
Check tire pressures more often if subject to a wide range
of outdoor temperatures, as tire pressures vary with
temperature changes.
STARTING AND OPERATING 491
Tire Pressures For High Speed Operation
Radial-Ply Tires
The manufacturer advocates driving at safe speeds
WARNING!
within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high
Combining radial ply tires with other types of tires
speeds, maintaining correct tire inflation pressure is very
on your vehicle will cause your vehicle to handle
important. Increased tire pressure and reduced vehicle
poorly. The instability could cause a collision. Alloading may be required for high-speed vehicle operaways use radial tires in sets of four. Never combine
tion. Refer to original equipment or an authorized tire
them with other types of tires.
dealer for recommended safe operating speeds, loading
and cold tire inflation pressures.
Cuts and punctures in radial tires are repairable only in
the tread area because of sidewall flexing. Consult your
WARNING!
authorized dealer for radial tire repairs.
High speed driving with your vehicle at or above
Spare Tire Matching Original Equipped Tire And
maximum load is dangerous. The added strain on
Wheel – If Equipped
your tires could cause them to fail. You could have a
Your vehicle may be equivalent with a spare tire and
serious collision. Do not drive a vehicle loaded to the
wheel in look and function as the original equipment tire
maximum capacity at continuous speeds above
and wheel found on the front or rear axle of your vehicle.
75 mph (120 km/h).
This spare tire may be used in the tire rotation for your
5
492 STARTING AND OPERATING
vehicle. If your vehicle has this option refer to an Compact Spare Tire – If Equipped
authorized tire dealer for the recommended tire rotation The compact spare is for temporary emergency use only.
You can identify if your vehicle is equipped with a
pattern.
compact spare by looking at the spare tire description on
If your vehicle is not equipped with an original equipthe Tire and Loading Information Placard located on the
ment tire and wheel as a spare, a non-matching tempodriver’s side door opening or on the sidewall of the tire.
rary emergency use spare may be equipped with your
Compact spare tire descriptions begin with the letter “T”
vehicle. Temporary use spares are engineered to be used
or “S” preceding the size designation. Example: T145/
only with your vehicle. Your vehicle may be equipped
80D18 103M.
with one of the following types of non-matching temporary use spares; compact, full size, or limited-use. Do not T, S = Temporary Spare Tire
install more than one non-matching temporary use spare
Since this tire has limited tread life the original equiptire/wheel on the vehicle at any given time.
ment tire should be repaired (or replaced) and reinstalled
on your vehicle at the first opportunity.
CAUTION!
Because of the reduced ground clearance, do not take
your vehicle through an automatic car wash with a
compact, full size or limited-use temporary spare
installed. Damage to the vehicle may result.
Do not install a wheel cover or attempt to mount a
conventional tire on the compact spare wheel, since the
wheel is designed specifically for the compact spare tire.
Do not install more than one compact spare tire and
wheel on the vehicle at any given time
STARTING AND OPERATING 493
WARNING!
Compact spares are for temporary emergency use
only. With these spares, do not drive more than
50 mph (80 km/h). Temporary use spares have limited
tread life. When the tread is worn to the tread wear
indicators, the temporary use spare tire needs to be
replaced. Be sure to follow the warnings, which
apply to your spare. Failure to do so could result in
spare tire failure and loss of vehicle control.
your original equipment tire, replace (or repair) the
original equipment tire and reinstall on the vehicle at the
first opportunity.
Limited-Use Spare – If Equipped
The limited-use spare tire is for temporary emergency
use only. This tire is identified by a label located on the
limited-use spare wheel. This label contains the driving
limitations for this spare. This tire may look like the
original equipped tire on the front or rear axle of your
vehicle, but it is not. Installation of this limited-use spare
tire affects vehicle handling. Since it is not the same as
Full Size Spare – If Equipped
your original equipment tire, replace (or repair) the
The full size spare is for temporary emergency use only.
original equipment tire and reinstall on the vehicle at the
This tire may look like the original equipped tire on the
first opportunity.
front or rear axle of your vehicle, but it is not. This spare
tire may have limited tread life. When the tread is worn
to the tread wear indicators, the temporary use full size
spare tire needs to be replaced. Since it is not the same as
5
494 STARTING AND OPERATING
WARNING!
WARNING!
Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle
handling. With this tire, do not drive more than the
speed listed on the limit-use spare wheel. Keep
inflated to the cold tire inflation pressure listed on
your Tire and Loading Information Placard located
on the driver’s side door opening. Replace (or repair)
the original equipment tire at the first opportunity
and reinstall it on your vehicle. Failure to do so could
result in loss of vehicle control.
Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than
30 mph (48 km/h) when you are stuck, and do not let
anyone near a spinning wheel no matter what the
speed.
Tire Spinning
When stuck in mud, sand, snow, or ice conditions, do not
spin your vehicle’s wheels above 30 mph (48 km/h).
Tread Wear Indicators
Tread wear indicators are in the original equipment tires
to help you in determining when your tires should be
replaced.
STARTING AND OPERATING 495
Life Of Tire
The service life of a tire is dependent upon various
factors including but not limited to:
• Driving style
• Tire pressure
• Distance driven
WARNING!
1 — Worn Tire
2 — New Tire
Tires and the spare tire should be replaced after six
years, regardless of the remaining tread. Failure to
follow this warning can result in sudden tire failure.
You could lose control and have an collision resulting
in serious injury or death.
These indicators are molded into the bottom of the tread
grooves. They will appear as bands when the tread depth
becomes 1/16 in (2 mm). When the tread is worn to the Keep dismounted tires in a cool, dry place with as little
exposure to light as possible. Protect tires from contact
tread wear indicators, the tire should be replaced.
with oil, grease, and gasoline.
5
496 STARTING AND OPERATING
Replacement Tires
The tires on your new vehicle provide a balance of many
characteristics. They should be inspected regularly for
wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance
when replacement is needed. (Refer to the paragraph on
“Tread Wear Indicators”). Refer to the “Tire and Loading
Information” placard for the size designation of your tire.
The Load Index and Speed Symbol for your tire will be
found on the original equipment tire sidewall. See the
Tire Sizing Chart example found in the Tire Safety
Information section of this manual for more information
relating to the Load Index and Speed Symbol of a tire.
It is recommended to replace the two front tires or two
rear tires as a pair. Replacing just one tire can seriously
affect your vehicle’s handling. If you ever replace a
wheel, make sure that the wheel’s specifications match
those of the original wheels.
It is recommended you contact your original equipment
or an authorized tire dealer with any questions you may
have on tire specifications or capability. Failure to use
equivalent replacement tires may adversely affect the
safety, handling, and ride of your vehicle.
WARNING!
• Do not use a tire, wheel size or rating other than
that specified for your vehicle. Some combinations
of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and
braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have
a collision resulting in serious injury or death. Use
only the tire and wheel sizes with load ratings
approved for your vehicle.
(Continued)
STARTING AND OPERATING 497
WARNING! (Continued)
• Never use a tire with a smaller load index or
capacity than what was originally equipped on
your vehicle. Using a tire with a smaller load index
could result in tire overloading and failure. You
could lose control and have a collision.
• Failure to equip your vehicle with tires having
adequate speed capability can result in sudden tire
failure and loss of vehicle control.
TIRE CHAINS (TRACTION DEVICES)
Use of traction devices require sufficient tire-to-body
clearance. Follow these recommendations to guard
against damage.
• Install on Rear Tires Only
• Due to limited clearance, use SAE class “S” low profile
cables or traction devices only. Security Chain Company (SCC) Super Z6 #SZ 441 cables or equivalent are
recommended.
CAUTION!
WARNING!
Replacing original tires with tires of a different size
may result in false speedometer and odometer readings.
Using tires of different size and type (M+S, Snow)
between front and rear axles can cause unpredictable
handling. You could lose control and have a collision.
5
498 STARTING AND OPERATING
CAUTION!
CAUTION! (Continued)
To avoid damage to your vehicle or tires, observe the
following precautions:
• Because of restricted traction device clearance between tires and other suspension components, it is
important that only traction devices in good condition are used. Broken devices can cause serious
damage. Stop the vehicle immediately if noise
occurs that could indicate device breakage. Remove the damaged parts of the device before
further use.
• Install device as tightly as possible and then
retighten after driving about 1⁄2 mile (0.8 km).
• Do not exceed 30 mph (48 km/h).
• Drive cautiously and avoid severe turns and large
bumps, especially with a loaded vehicle.
• Do not drive for prolonged period on dry pavement.
• Observe the traction device manufacturer’s instructions on the method of installation, operating
speed, and conditions for use. Always use the
suggested operating speed of the device manufacturer’s if it is less than 30 mph (48 km/h).
• Do not use traction devices on a compact spare tire.
SNOW TIRES
Some areas of the country require the use of snow tires
during the winter. All season tires can be identified by the
M+S designation on the tire sidewall.
If you need snow tires, select tires equivalent in size and
type to the original equipment tires. Use snow tires only
(Continued) in sets of four; failure to do so may adversely affect the
safety and handling of your vehicle.
STARTING AND OPERATING 499
Snow tires generally have lower speed ratings than what
was originally equipped with your vehicle and should
not be operated at sustained speeds over 75 mph
(120 km/h). For speeds above 75 mph (120 km/h) refer to
original equipment or an authorized tire dealer for
recommended safe operating speeds, loading and cold
tire inflation pressures.
While studded tires improve performance on ice, skid
and traction capability on wet or dry surfaces may be
poorer than that of non-studded tires. Some states prohibit studded tires; therefore, local laws should be
checked before using these tire types.
These effects can be reduced by timely rotation of tires.
The benefits of rotation are especially worthwhile with
aggressive tread designs such as those on On/Off-Road
type tires. Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to
a smooth, quiet ride.
Refer to the “Maintenance Schedule” for the proper
maintenance intervals. More frequent rotation is permissible if desired. The reasons for any rapid or unusual
wear should be corrected prior to rotation being performed.
NOTE: The premium Tire Pressure Monitor System will
automatically locate the pressure values displayed in the
TIRE ROTATION RECOMMENDATIONS
The tires on the front and rear of your vehicle operate at correct vehicle position following a tire rotation.
different loads and perform different steering, handling,
and braking functions. For these reasons, they wear at
unequal rates.
5
500 STARTING AND OPERATING
The suggested rotation method is the “forward-cross” TIRE PRESSURE MONITOR SYSTEM (TPMS)
The Tire Pressure Monitoring System (TPMS) will warn
shown in the following diagram.
the driver of a low tire pressure based on the vehicle
recommended cold tire pressure.
Tire Rotation
The tire pressure will vary with temperature by about
1 psi (7 kPa) for every 12°F (6.5°C). This means that when
the outside temperature decreases, the tire pressure will
decrease. Tire pressure should always be set based on
cold inflation tire pressure. This is defined as the tire
pressure after the vehicle has not been driven for at least
three hours, or driven less than 1 mile (1.6 km) after a
three-hour period. Refer to “Tires – General Information” in “Starting and Operating” for information on
how to properly inflate the vehicle’s tires. The tire
pressure will also increase as the vehicle is driven - this is
normal and there should be no adjustment for this
increased pressure.
STARTING AND OPERATING 501
The TPMS will warn the driver of a low tire pressure if
the tire pressure falls below the low pressure warning
threshold for any reason, including low temperature
effects, or natural pressure loss through the tire.
The TPMS will continue to warn the driver of low tire
pressure as long as the condition exists, and will not turn
off until the tire pressure is at or above recommended
cold tire pressure. Once the low tire pressure warning has
been illuminated, the tire pressure must be increased to
the recommended cold tire pressure in order for the “Tire
Pressure Monitoring Telltale Light” to be turned off. The
system will automatically update and the “Tire Pressure
Monitoring Telltale Light” will extinguish once the updated tire pressures have been received. The vehicle may
need to be driven for up to 20 minutes above 15 mph
(24 km/h) to receive this information.
For example, your vehicle has a recommended cold
(parked for more than three hours) tire pressure of 33 psi
(227 kPa). If the ambient temperature is 68°F (20°C) and
the measured tire pressure is 28 psi (193 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to
approximately 24 psi (165 kPa). This tire pressure is
sufficiently low enough to turn ON the “Tire Pressure
Monitoring Telltale Light.” Driving the vehicle may cause
the tire pressure to rise to approximately 28 psi (193 kPa),
but the “Tire Pressure Monitoring Telltale Light” will still
be ON. In this situation, the “Tire Pressure Monitoring
Telltale Light” will turn OFF only after the tires have been
inflated to the vehicle’s recommended cold tire pressure
value.
5
502 STARTING AND OPERATING
CAUTION!
• The TPMS has been optimized for the original
equipment tires and wheels. TPMS pressures have
been established for the tire size equipped on your
vehicle. Undesirable system operation or sensor
damage may result when using replacement
equipment that is not of the same size, type, and/or
style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealants or balance
beads if your vehicle is equipped with a TPMS, as
damage to the sensors may result.
• After inspecting or adjusting the tire pressure
always reinstall the valve stem cap. This will
prevent moisture and dirt from entering the valve
stem, which could damage the Tire Pressure Monitoring Sensor.
NOTE:
• The TPMS is not intended to replace normal tire care
and maintenance, or to provide warning of a tire
failure or condition.
• The TPMS should not be used as a tire pressure gauge
while adjusting your tire pressure.
• Driving on a significantly under-inflated tire causes
the tire to overheat and can lead to tire failure.
Under-inflation also reduces fuel efficiency and tire
tread life, and may affect the vehicle’s handling and
stopping ability.
• The TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain
correct tire pressure using an accurate tire gauge, even
if under-inflation has not reached the level to trigger
illumination of the “Tire Pressure Monitoring Telltale
Light.”
STARTING AND OPERATING 503
• Seasonal temperature changes will affect tire pressure, A tire pressure monitoring sensor is located in the spare
and the TPMS will monitor the actual tire pressure in wheel, if the vehicle is equipped with a matching full-size
spare wheel and tire assembly. The matching full-size
the tire.
spare tire can be used in place of any of the four road
Base System
tires. A low spare tire will not cause the “Tire Pressure
The Tire Pressure Monitor System (TPMS) uses wireless
Monitoring Telltale Light” to illuminate, a warning mestechnology with wheel rim-mounted electronic sensors to
sage to appear, or the chime to sound.
monitor tire pressure levels. Sensors, mounted to each
The “Tire Pressure Monitoring Telltale Light” will
wheel as part of the valve stem, transmit tire pressure
illuminate in the instrument cluster, a “LOW TIRE
readings to the Receiver Module.
PRESSURE” message will display in the instruNOTE: It is particularly important, for you to regularly
ment cluster for a minimum of five seconds, and an
check the tire pressure in all of your tires, and to maintain
audible chime will be activated, when one or more of the
the proper pressure.
four active road tire pressures are low. Should this occur,
you should stop as soon as possible, check the inflation
The TPMS consists of the following components:
pressure of each tire on your vehicle, and inflate each tire
• Receiver Module
to the vehicle’s recommended cold placard pressure
value. The system will automatically update and the
• Four Tire Pressure Monitoring Sensors
“Tire Pressure Monitoring Telltale Light” will extinguish,
• Tire Pressure Monitoring Telltale Light
once the updated tire pressures have been received. The
5
504 STARTING AND OPERATING
vehicle may need to be driven for up to 20 minutes above 3. Lots of snow or ice around the wheels or wheel
15 mph (24 km/h) to receive this information.
housings.
The “Tire Pressure Monitoring Telltale Light” will flash
on and off for 75 seconds, and remain on solid when a
system fault is detected. In addition, a “SERVICE TPM
SYSTEM” message will be displayed for a minimum of
five seconds when a system fault is detected, and a chime
will sound. If the ignition switch is cycled, this sequence
will repeat, providing the system fault still exists. The
“Tire Pressure Monitoring Telltale Light” will turn off
when the fault condition no longer exists. A system fault
can occur by any of the following:
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM sensors.
NOTE:
• If your vehicle is equipped with a matching full-size
spare wheel and tire assembly, it has a tire pressure
monitoring sensor, and can be monitored by the Tire
Pressure Monitoring System (TPMS). In the event that
the matching full-size spare tire is swapped with a low
pressure road tire, the next ignition switch cycle will
still show the “Tire Pressure Monitoring Telltale Light”
1. Jamming due to electronic devices or driving next to
to be ON, a “LOW TIRE PRESSURE” message will be
facilities emitting the same Radio Frequencies as the TPM
displayed in the instrument cluster for a minimum of
sensors.
five seconds, and a chime to sound. Driving the
vehicle for up to 20 minutes above 15 mph (24 km/h)
2. Installing some form of aftermarket window tinting
that affects radio wave signals.
STARTING AND OPERATING 505
will turn OFF the “Tire Pressure Monitoring Telltale
Light” as long as none of the road tires are below the
low pressure warning threshold.
• If your vehicle is not equipped with a matching
full-size spare wheel and tire assembly, it does not
have a tire pressure monitoring sensor in the spare tire.
The TPMS will not be able to monitor the tire pressure.
If you install the spare tire, in place of a road tire, that
has a pressure below the low-pressure warning limit,
upon the next ignition switch cycle, a chime will
sound, a “LOW TIRE PRESSURE” message will be
displayed in the instrument cluster for a minimum of
five seconds, and the “Tire Pressure Monitoring Telltale Light” will turn ON. After driving the vehicle for
up to 20 minutes above 15 mph (24 km/h), the “Tire
Pressure Monitoring Telltale Light” will flash on and
off for 75 seconds and then remain on solid. In
addition, a “SERVICE TPM SYSTEM” message will be
displayed for a minimum of five seconds. For each
subsequent ignition switch cycle, a chime will sound,
a “SERVICE TPM SYSTEM” message will be displayed
for a minimum of five seconds, and the “Tire Pressure
Monitoring Telltale Light” will flash on and off for
75 seconds and then remain on solid. Once you repair
or replace the original road tire, and reinstall it on the
vehicle in place of the spare tire, the TPMS will update
automatically and the “Tire Pressure Monitoring Telltale Light” will turn OFF, as long as no tire pressure is
below the low-pressure warning limit in any of the
four active road tires. The vehicle may need to be
driven for up to 20 minutes above 15 mph (24 km/h)
in order for the TPMS to receive this information.
Premium System – If Equipped
The Tire Pressure Monitor System (TPMS) uses wireless
technology with wheel rim-mounted electronic sensors to
monitor tire pressure levels. Sensors, mounted to each
wheel as part of the valve stem, transmit tire pressure
readings to the Receiver Module.
5
506 STARTING AND OPERATING
NOTE: It is particularly important, for you to regularly Tire Pressure Monitoring Low Pressure Warnings
The “Tire Pressure Monitoring Telltale Light” will
check the tire pressure in all of your tires and to maintain
illuminate in the instrument cluster, and an authe proper pressure.
dible chime will be activated, when one or more of
The Tire Pressure Monitor System (TPMS) consists of the
the four active road tire pressures are low. In addition, the
following components:
EVIC will display a “LOW TIRE MESSAGE” message for
• Receiver Module
a minimum of five seconds, and a graphic display of the
pressure value(s) with the low tire(s) “flashing.” Refer to
• Four Tire Pressure Monitoring Sensors
“Electronic Vehicle Information Center (EVIC)” in “Un• Various Tire Pressure Monitoring System Messages, derstanding Your Instrument Panel” for further informawhich display in the Electronic Vehicle Information tion.
Center (EVIC), and a graphic displaying tire pressures
NOTE: Your system can be set to display pressure units
• Tire Pressure Monitoring Telltale Light
in PSI, kPa, or BAR.
A tire pressure monitoring sensor is located in the spare
wheel, if the vehicle is equipped with a matching full-size
spare wheel and tire assembly. The matching full-size
spare tire can be used in place of any of the four road
tires.
STARTING AND OPERATING 507
The system will automatically update, the graphic display of the pressure value(s) will stop “flashing,” and the
“Tire Pressure Monitoring Telltale Light” will extinguish
once the updated tire pressure(s) have been received. The
vehicle may need to be driven for up to 20 minutes above
15 mph (24 km/h) to receive this information.
SERVICE TPM SYSTEM Warning
The “Tire Pressure Monitoring Telltale Light” will flash
on and off for 75 seconds, and remain on solid when a
system fault is detected. The system fault will also sound
a chime. The EVIC will display a “SERVICE TPM SYSTEM” message for a minimum of five seconds. This
Should a low tire condition occur on any of the four
message is then followed by a graphic display, with “- -“
active road tire(s), you should stop as soon as possible,
in place of the pressure value(s), indicating which Tire
and inflate the low tire(s) that is “flashing” on the graphic
Pressure Monitoring Sensor(s) is not being received.
display to the vehicle’s recommended cold tire pressure.
5
508 STARTING AND OPERATING
NOTE: Your system can be set to display pressure units message will not be present, and a pressure value will be
in PSI, kPa, or BAR.
displayed instead of dashes. A system fault can occur by
any of the following:
1. Jamming due to electronic devices or driving next to
facilities emitting the same Radio Frequencies as the TPM
sensors.
2. Installing some form of aftermarket window tinting
that affects radio wave signals.
3. Lots of snow or ice around the wheels or wheel
housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM sensors.
If the ignition switch is cycled, this sequence will repeat,
providing the system fault still exists. If the system fault The EVIC will also display a ⬙SERVICE TPM SYSTEM⬙
no longer exists, the “Tire Pressure Monitoring Telltale message for a minimum of five seconds when a system
Light” will no longer flash, the ⬙SERVICE TPM SYSTEM⬙ fault is detected possibly related to an incorrect sensor
location fault. In this case, the ⬙SERVICE TPM SYSTEM⬙
STARTING AND OPERATING 509
Pressure Monitoring Telltale Light” as long as none of
message is then followed by a graphic display, with
road tires are below the low pressure warning threshpressure values still shown. This indicates the pressure
old.
values are still being received from the TPM Sensors but
they may not be located in the correct vehicle position.
• If your vehicle is not equipped with a matching
However, the system still needs to be serviced as long as
full-size spare wheel and tire assembly, it does not
the ⬙SERVICE TPM SYSTEM⬙ message exists.
have a tire pressure monitoring sensor in the spare tire.
The TPMS will not be able to monitor the tire pressure.
NOTE:
• If your vehicle is equipped with a matching full-size
If you install the spare tire in place of a road tire that
spare wheel and tire assembly, it has a tire pressure
has a pressure below the low-pressure warning limit,
monitoring sensor, and can be monitored by the Tire
upon the next ignition switch cycle, the “Tire Pressure
Pressure Monitoring System (TPMS). In the event that
Monitoring Telltale Light” will remain ON, a chime
the matching full-size spare tire is swapped with a low
will sound, and the EVIC will still display a “flashing”
pressure road tire, the next ignition switch cycle will
pressure value in the graphic display. After driving the
still show the “Tire Pressure Monitoring Telltale Light”
vehicle for up to 20 minutes above 15 mph (24 km/h),
to be ON, a chime to sound, a “LOW TIRE PRESthe “Tire Pressure Monitoring Telltale Light” will flash
SURE” message to appear in the EVIC, and the
on and off for 75 seconds and then remain on solid. In
graphic display will still show the low tire pressure
addition, the EVIC will display a “SERVICE TPM
value “flashing.” Driving the vehicle for up to 20 minSYSTEM⬙ message for a minimum of five seconds and
utes above 15 mph (24 km/h) will turn OFF the “Tire
then display dashes (- -) in place of the pressure value.
5
510 STARTING AND OPERATING
For each subsequent ignition switch cycle, a chime will
sound, the “Tire Pressure Monitoring Telltale Light”
will flash on and off for 75 seconds and then remain on
solid, and the EVIC will display a ⬙SERVICE TPM
SYSTEM⬙ message for a minimum of five seconds and
then display dashes (- -) in place of the pressure value.
Once you repair or replace the original road tire, and
reinstall it on the vehicle in place of the spare tire, the
TPMS will update automatically.
General Information
This device complies with part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:
In addition, the “Tire Pressure Monitoring Telltale Light”
will turn OFF and the graphic in the EVIC will display a
new pressure value instead of dashes (- -), as long as no
tire pressure is below the low-pressure warning limit in
any of the four active road tires. The vehicle may need to
be driven for up to 20 minutes above 15 mph (24 km/h)
in order for the TPMS to receive this information.
The tire pressure sensors are covered under one of the
following licenses:
• This device may not cause harmful interference.
• This device must accept any interference received,
including interference that may cause undesired
operation.
United States . . . . . . . . . . . . . . . . . . . MRXC4W4MA4
Canada . . . . . . . . . . . . . . . . . . . . . 2546A-C4W4MA4
STARTING AND OPERATING 511
FUEL REQUIREMENTS
3.6L Engine – If Equipped
This engine is designed to meet all emissions regulations and provide excellent
fuel economy and performance when using high-quality unleaded “regular” gasoline having an octane rating of 87. The use
of premium gasoline is not recommended,
as it will not provide any benefit over regular gasoline in
these engines.
5.7L Engine – If Equipped
This engine is designed to meet all emissions regulations and provide satisfactory
fuel economy and performance when using high-quality unleaded gasoline having
an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for
optimum performance. The use of premium gasoline is
not recommended, as it will not provide any benefit over
regular gasoline in these engines.
Light spark knock at low engine speeds is not harmful to
your engine. However, continued heavy spark knock at
high speeds can cause damage and immediate service is
required. Poor quality gasoline can cause problems such
as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline
before considering service for the vehicle.
Over 40 auto manufacturers worldwide have issued and
endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties
necessary to deliver enhanced emissions, performance,
and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
5
512 STARTING AND OPERATING
Reformulated Gasoline
Many areas of the country require the use of cleaner
burning gasoline referred to as “Reformulated Gasoline.”
Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality.
The manufacturer supports the use of reformulated gasoline. Properly blended reformulated gasoline will provide excellent performance and durability of engine and
fuel system components.
Gasoline/Oxygenate Blends
Some fuel suppliers blend unleaded gasoline with oxygenates such as Ethanol. Fuels blended with oxygenates
may be used in your vehicle.
CAUTION!
DO NOT use gasoline containing Methanol or gasoline containing more than 10% Ethanol. Use of these
blends may result in starting and driveability problems, damage critical fuel system components, cause
emissions to exceed the applicable standard, and/or
cause the “Malfunction Indicator Light” to illuminate. Pump labels should clearly communicate if a
fuel contains greater than 10% Ethanol.
Problems that result from using gasoline containing
Methanol or gasoline containing more than 10% Ethanol
are not the responsibility of the manufacturer and may
not be covered under warranty.
E-85 Usage In Non-Flex Fuel Vehicles
Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol
content may void the vehicle’s warranty.
STARTING AND OPERATING 513
If a Non-FFV vehicle is inadvertently fueled with E-85 MMT In Gasoline
fuel, the engine will have some or all of these symptoms: MMT is a manganese-containing metallic additive that is
blended into some gasoline to increase octane. Gasoline
• operate in a lean mode
blended with MMT provides no performance advantage
• OBD II “Malfunction Indicator Light” on
beyond gasoline of the same octane number without
MMT. Gasoline blended with MMT reduces spark plug
• poor engine performance
life and reduces emissions system performance in some
• poor cold start and cold driveability
vehicles. The manufacturer recommends that gasoline
without MMT be used in your vehicle. The MMT content
• increased risk for fuel system component corrosion
of gasoline may not be indicated on the gasoline pump,
To fix a Non-FFV vehicle inadvertently fueled once with therefore, you should ask your gasoline retailer whether
E-85 perform the following:
the gasoline contains MMT. It is even more important to
look for gasoline without MMT in Canada, because MMT
• change the engine oil and oil filter
can be used at levels higher than those allowed in the
• disconnect and reconnect the battery
United States. MMT is prohibited in Federal and California reformulated gasoline.
• drain the fuel tank (see your authorized dealer)
More extensive repairs will be required for prolonged
exposure to E-85 fuel.
5
514 STARTING AND OPERATING
Materials Added To Fuel
All gasoline sold in the United States is required to
contain effective detergent additives. Use of additional
detergents or other additives is not needed under normal
conditions and they would result in additional cost.
Therefore, you should not have to add anything to the
fuel.
Fuel System Cautions
CAUTION!
Follow these guidelines to maintain your vehicle’s
performance:
• The use of leaded gas is prohibited by Federal law.
Using leaded gasoline can impair engine performance and damage the emissions control system.
CAUTION! (Continued)
• An out-of-tune engine or certain fuel or ignition
malfunctions can cause the catalytic converter to
overheat. If you notice a pungent burning odor or
some light smoke, your engine may be out of tune
or malfunctioning and may require immediate
service. Contact your authorized dealer for service
assistance.
• The use of fuel additives, which are now being
sold as octane enhancers, is not recommended.
Most of these products contain high concentrations of methanol. Fuel system damage or vehicle
performance problems resulting from the use of
such fuels or additives is not the responsibility of
the manufacturer.
(Continued) NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed
against you.
STARTING AND OPERATING 515
Carbon Monoxide Warnings
WARNING! (Continued)
WARNING!
Carbon monoxide (CO) in exhaust gases is deadly.
Follow the precautions below to prevent carbon
monoxide poisoning:
• Do not inhale exhaust gases. They contain carbon
monoxide, a colorless and odorless gas, which can
kill. Never run the engine in a closed area, such as
a garage, and never sit in a parked vehicle with the
engine running for an extended period. If the
vehicle is stopped in an open area with the engine
running for more than a short period, adjust the
ventilation system to force fresh, outside air into
the vehicle.
• Guard against carbon monoxide with proper
maintenance. Have the exhaust system inspected
every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired,
drive with all side windows fully open.
• Keep the liftgate closed when driving your vehicle
to prevent carbon monoxide and other poisonous
exhaust gases from entering the vehicle.
FLEXIBLE FUEL (3.6L ENGINE ONLY) —
IF EQUIPPED
E-85 General Information
The information in this section is for Flexible Fuel vehicles only. These vehicles can be identified by a unique
(Continued)
fuel filler door label that states Ethanol (E-85) or Unleaded Gasoline Only. This section only covers those
subjects that are unique to these vehicles. Please refer to
5
516 STARTING AND OPERATING
the other sections of this manual for information on
features that are common between Flexible Fuel and
gasoline-only powered vehicles.
CAUTION!
Only vehicles with the E-85 fuel filler door label can
operate on E-85.
E-85 Fuel Cap
E-85 Badge
STARTING AND OPERATING 517
Ethanol Fuel (E-85)
When you do switch fuel types it is recommended that:
E-85 is a mixture of approximately 85% fuel ethanol and
• you do not switch when the fuel gauge indicates less
15% unleaded gasoline.
than 1/4 full
WARNING!
Ethanol vapors are extremely flammable and could
cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the
tank. Do not use E-85 as a cleaning agent and never
use it near an open flame.
• you do not add less than 5 gallons (19 Liters) when
refueling
• you operate the vehicle immediately after refueling for
a period of at least 5 minutes
Observing these precautions will avoid possible hard
starting and/or significant deterioration in driveability
during warm up.
NOTE:
Fuel Requirements
Your vehicle will operate on both unleaded gasoline with • When the ambient temperature is above 90° F (32° C),
you may experience hard starting and rough idle
an octane rating of 87, or E-85 fuel, or any mixture of
following start up even if the above recommendations
these two. For best results, a refueling pattern that
are followed.
alternates between E-85 and unleaded gasoline should be
avoided.
5
518 STARTING AND OPERATING
• Some additives used in regular gasoline are not fully
compatible with E-85 and may form deposits in your
engine. To eliminate driveability issues that may be
caused by these deposits, a supplemental gasoline
additive, such as MOPAR威 Injector Cleanup or
Techron may be used.
Selection Of Engine Oil For Flexible Fuel Vehicles
(E-85) And Gasoline Vehicles
FFV vehicles operated on E-85 require specially formulated engine oils. These special requirements are included
in MOPAR威 engine oils, and in equivalent oils meeting
Chrysler Specification MS-6395. The manufacturer requires engine oils that are API Certified and meet the
requirements of Material Standard MS-6395. MS-6395
contains additional requirements, developed during extensive fleet testing, to provide additional protection to
Chrysler Group LLC engines. Use MOPAR威 or an
equivalent oil meeting the specification MS-6395.
Starting
The characteristics of E-85 fuel make it unsuitable for use
when ambient temperatures fall below 0°F (-18°C). In the
range of 0°F (-18°C) to 32°F (0°C), you may experience an
increase in the time it takes for your engine to start, and
a deterioration in driveability (sags and/or hesitations)
until the engine is fully warmed up.
NOTE: Use of the engine block heater (if equipped) is
beneficial for E-85 startability when the ambient temperature is less than 32°F (0°C).
Cruising Range
Because E-85 fuel contains less energy per gallon/liter
than gasoline, you will experience an increase in fuel
consumption. You can expect your miles per gallon
(mpg)/miles per liter and your driving range to decrease
by about 30%, compared to gasoline operation.
STARTING AND OPERATING 519
Replacement Parts
Maintenance
Many components in your Flexible Fuel Vehicle (FFV) are
CAUTION!
designed to be compatible with ethanol. Always be sure
that your vehicle is serviced with correct ethanol comDo not use ethanol mixture greater than 85% in your
patible parts.
vehicle. It will cause difficulty in cold starting and
may affect driveability.
CAUTION!
Replacing fuel system components with non-ethanol
compatible components can damage your vehicle.
ADDING FUEL
Fuel Filler Cap (Gas Cap)
The gas cap is located behind the locking fuel filler door,
on the driver’s side of the vehicle. If the gas cap is lost or
damaged, be sure the replacement cap is for use with this
vehicle.
5
520 STARTING AND OPERATING
1. Press the fuel filler door release switch (located under 2. Open the fuel filler door, and remove the fuel filler
the headlamp switch).
cap.
Fuel Filler Door Release Switch
Fuel Filler Cap
STARTING AND OPERATING 521
CAUTION!
WARNING!
• Damage to the fuel system or emission control
system could result from using an improper fuel
cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting
aftermarket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors
escaping from the system.
• A poorly fitting gas cap may cause the MIL to turn
on.
• To avoid fuel spillage and overfilling, do not “top
off” the fuel tank after filling.
• Never have any smoking materials lit in or near
the vehicle when the gas cap is removed or the
tank is being filled.
• Never add fuel when the engine is running. This is
in violation of most state and federal fire regulations and may cause the malfunction indicator
light to turn on.
• A fire may result if gasoline is pumped into a
portable container that is inside of a vehicle. You
could be burned. Always place gas containers on
the ground while filling.
NOTE:
• When the fuel nozzle “clicks” or shuts off, the fuel
tank is full.
5
522 STARTING AND OPERATING
• Tighten the gas cap about one-quarter turn until you
hear one click. This is an indication that the cap is
properly tightened.
• If the gas cap is not tighten properly, the MIL will
come on. Be sure the gas cap is tightened every time
the vehicle is refueled.
Emergency Fuel Filler Door Release
If you are unable to open the fuel filler door, use the fuel
filler door emergency release.
1. Open the liftgate.
Release Cable
2. Push down on the inboard edge of the left storage bin,
Loose Fuel Filler Cap Message
this will pop up the outboard edge.
If the vehicle diagnostic system determines
3. Grab popped up outboard edge with other hand to
that the fuel filler cap is loose, improperly
disengage snaps.
installed, or damaged, a loose gascap indicator
will display in the EVIC telltale display area.
4. Remove the storage bin.
Refer to “Electronic Vehicle Information Center (EVIC)”
5. Pull the release cable.
STARTING AND OPERATING 523
in “Understanding Your Instrument Panel” for further
information. Tighten the fuel filler cap properly and press
the SELECT button to turn off the message. If the
problem continues, the message will appear the next time
the vehicle is started.
VEHICLE LOADING
Certification Label
As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label
affixed to the driver’s side door or B-Pillar.
Gross Vehicle Weight Rating (GVWR)
The GVWR is the total permissible weight of your vehicle
including driver, passengers, vehicle, options, trailer
tongue weight, and cargo. The label also specifies maximum capacities of front and rear axle systems (GAWR).
Total load must be limited, so GVWR, and front and rear
GAWR are not exceeded.
Payload
The payload of a vehicle is defined as the allowable load
weight a truck or any given vehicle can carry, including
the weight of the driver, all passengers, options and
This label contains the month and year of manufacture, cargo.
Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Gross Axle Weight Rating (GAWR)
Rating (GAWR) front and rear, and Vehicle Identification The GAWR is the maximum permissible load on the front
Number (VIN). A Month-Day-Hour (MDH) number is and rear axles. The load must be distributed in the cargo
included on this label and indicates the month, day, and area so that the GAWR of each axle is not exceeded.
hour of manufacture. The bar code that appears on the
Each axle’s GAWR is determined by the components in
bottom of the label is your VIN.
the system with the lowest load carrying capacity (axle,
5
524 STARTING AND OPERATING
springs, tires, or wheels). Heavier axles or suspension
components, sometimes specified by purchasers for increased durability, does not necessarily increase the vehicle’s GVWR.
capacity conditions, and with no occupants or cargo
loaded into the vehicle. The front and rear curb weight
values are determined by weighing your vehicle on a
commercial scale before any occupants or cargo are
added.
Tire Size
The tire size on the label represents the actual tire size on Loading
your vehicle. Replacement tires must be equal to the load The actual total weight and the weight of the front and
capacity of this tire size.
rear of your vehicle at the ground can best be determined
by weighing it when it is loaded and ready for operation.
Rim Size
This is the rim size that is appropriate for the tire size The entire vehicle should first be weighed on a commerlisted.
cial scale to ensure that the GVWR has not been exceeded. The weight on the front and rear of the vehicle
Inflation Pressure
should then be determined separately to be sure that the
This is the cold tire inflation pressure for your vehicle for
load is properly distributed over front and rear axle.
all loading conditions up to full GAWR.
Weighing the vehicle may show that the GAWR of either
Curb Weight
the front or rear axles has been exceeded, but the total
The curb weight of a vehicle is defined as the total weight load is within the specified GVWR. If so, weight must be
of the vehicle with all fluids, including vehicle fuel, at full shifted from front to rear, or rear to front, as appropriate
STARTING AND OPERATING 525
until the specified weight limitations are met. Store the
heavier items down low and be sure that the weight is
distributed equally. Stow all loose items securely before
driving.
TRAILER TOWING
In this section you will find safety tips and information
on limits to the type of towing you can reasonably do
with your vehicle. Before towing a trailer, carefully
review this information to tow your load as efficiently
Improper weight distributions can have an adverse affect
and safely as possible.
on the way your vehicle steers and handles, and the way
To maintain warranty coverage, follow the requirements
the brakes operate.
and recommendations in this manual concerning veCAUTION!
hicles used for trailer towing.
Do not load your vehicle any heavier than the GVWR
or the maximum front and rear GAWR. If you do,
parts on your vehicle can break, or it can change the
way your vehicle handles. This could cause you to
lose control. Also, overloading can shorten the life of
your vehicle.
Common Towing Definitions
The following trailer towing related definitions will assist
you in understanding the following information.
Gross Vehicle Weight Rating (GVWR)
The GVWR is the total allowable weight of your vehicle.
This includes driver, passengers, cargo and trailer tongue
weight. The total load must be limited so that you do not
5
526 STARTING AND OPERATING
exceed the GVWR. Refer to “Vehicle Loading/Vehicle Gross Combination Weight Rating (GCWR)
Certification Label” in “Starting and Operating” for The GCWR is the total permissible weight of your vehicle
and trailer when weighed in combination.
further information.
Gross Trailer Weight (GTW)
The GTW is the weight of the trailer plus the weight of all
cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and
ready for operation⬙ condition.
NOTE: The GCWR rating includes a 150 lbs (68 kg)
allowance for the presence of a driver.
Gross Axle Weight Rating (GAWR)
The GAWR is the maximum capacity of the front and rear
axles. Distribute the load over the front and rear axles
The recommended way to measure GTW is to put your evenly. Make sure that you do not exceed either front or
fully loaded trailer on a vehicle scale. The entire weight rear GAWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for further
of the trailer must be supported by the scale.
information.
WARNING!
If the gross trailer weight is 3,500 lbs (1 587 kg) or
more, it is mandatory to use a weight-distributing
hitch to ensure stable handling of your vehicle. If
you use a standard weight-carrying hitch, you could
lose control of your vehicle and cause a collision.
WARNING!
It is important that you do not exceed the maximum
front or rear GAWR. A dangerous driving condition
can result if either rating is exceeded. You could lose
control of the vehicle and have a collision.
STARTING AND OPERATING 527
Trailer Tongue Weight (TW)
The TW is the downward force exerted on the hitch ball
by the trailer. In most cases it should not be less than 10%
or more than 15% of the trailer load. You must consider
this as part of the load on your vehicle.
Weight-Carrying Hitch
A weight-carrying hitch supports the trailer tongue
weight, just as if it were luggage located at a hitch ball or
some other connecting point of the vehicle. These kind of
hitches are the most popular on the market today and
they are commonly used to tow small- and mediumsized trailers.
Frontal Area
The frontal area is the maximum height multiplied by the
Weight-Distributing Hitch
maximum width of the front of a trailer.
A weight-distributing hitch system works by applying
Trailer Sway Control
leverage through spring (load) bars. They are typically
The trailer sway control can be a mechanical telescoping
used for heavier loads, to distribute trailer tongue weight
link that can be installed between the hitch receiver and
to the tow vehicle’s front axle and the trailer axle(s).
the trailer tongue that typically provides adjustable fricWhen used in accordance with the manufacturers’ direction associated with the telescoping motion to dampen
tions, it provides for a more level ride, offering more
any unwanted trailer swaying motions while traveling.
consistent steering and brake control, thereby enhancing
If equipped, the electronic Trailer Sway Control (TSC) towing safety. The addition of a friction/hydraulic sway
recognizes a swaying trailer and automatically applies control also dampens sway caused by traffic and crossindividual wheel brakes and/or reduces engine power to winds, and contributes positively to tow vehicle and
attempt to eliminate the trailer sway.
5
528 STARTING AND OPERATING
trailer stability. A friction/hydraulic sway control mechanism and a weight distributing (load equalizing) hitch
are recommended for heavier trailer tongue weights
(TW) and may be required depending on Vehicle and
Trailer configuration/loading to comply with gross axle
weight rating (GAWR) requirements.
WARNING!
• An improperly adjusted weight-distributing hitch
system may reduce handling, stability, and braking performance, and could result in a collision.
• Weight-distributing hitch systems may not be
compatible with Surge Brake Couplers. Consult
with your hitch and trailer manufacturer or a
reputable Recreational Vehicle dealer for additional information.
Without Weight-Distributing Hitch (Incorrect)
STARTING AND OPERATING 529
5
With Weight-Distributing Hitch (Correct)
Improper Adjustment of Weight-Distributing
Hitch (Incorrect)
530 STARTING AND OPERATING
Trailer Hitch Classification
Your vehicle may be factory equipped for safe towing of
trailers weighing over 3,500 lbs (1 587 kg) with the
optional Trailer Tow Prep Package. See your authorized
dealer for package content.
The following chart provides the industry standard for
the maximum trailer weight a given trailer hitch class can
tow and should be used to assist you in selecting the
correct trailer hitch for your intended towing condition.
Refer to the Trailer Towing Weights (Maximum Trailer
Weight Ratings) chart for the Max. GTW towable for your
given drivetrain.
Trailer Hitch Classification Definitions
Class
Max. Trailer Hitch Industry
Standards
Class I - Light Duty
2,000 lbs (907 kg)
Class II - Medium
3,500 lbs (1 587 kg)
Duty
Class III - Heavy Duty
5,000 lbs (2 268 kg)
Class IV - Extra
10,000 lbs (4 540 kg)
Heavy Duty
Refer to the “Trailer Towing Weights (Maximum
Trailer Weight Ratings)” chart for the Maximum
Gross Trailer Weight (GTW) towable for your given
drivetrain.
All trailer hitches should be professionally installed on
your vehicle.
STARTING AND OPERATING 531
Trailer Towing Weights (Maximum Trailer Weight Ratings)
The following chart provides the maximum trailer weight ratings towable for your given drivetrain.
Engine/Model Model
GCWR (Gross Combined Wt. Rating)
Frontal Area
Max. GTW (Gross
Trailer Wt.)
Max. Trailer
Tongue Wt.
(See Note)
3.6L
RWD
11,600 lbs (5 262 kg)
40 sq ft (3.72 sq m)
6,200 lbs (2 812 kg)
620 lbs (281 kg)
3.6L
AWD
11,600 lbs (5 262 kg)
40 sq ft (3.72 sq m)
6,200 lbs (2 812 kg)
620 lbs (281 kg)
5.7L
RWD
13,100 lbs (5 942 kg)
60 sq ft (5.57 sq m)
7,200 lbs (3 266 kg)
720 lbs (327 kg)
5.7L
AWD
13,100 lbs (5 942 kg)
60 sq ft (5.57 sq m)
7,200 lbs (3 266 kg)
720 lbs (327 kg)
Refer to local laws for maximum trailer towing speeds.
NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and
cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to
“Tire Safety Information” in “Starting and Operating” for further information. The addition of passengers
and cargo may require reducing trailer tongue load and Gross Trailer Weight (GTW). Redistributing cargo
(to the trailer) may be necessary to avoid exceeding Rear Gross Axle Weight Rating (GAWR) of 3,900 lbs
(1 769 kg).
5
532 STARTING AND OPERATING
If the gross trailer weight is 3,500 lbs (1 587 kg) or more,
it is mandatory to use a weight-distributing hitch to
ensure stable handling of your vehicle.
NOTE: Vehicles not factory equipped with trailer tow
package are limited to 3,500 lbs (350 lbs tongue weight).
Trailer And Tongue Weight
Always load a trailer with 60% to 65% of the weight in
the front of the trailer. This places 10% to 15% of the
Gross Trailer Weight (GTW) on the tow hitch of your
vehicle. Loads balanced over the wheels, or heavier in the
rear, can cause the trailer to sway severely side-to-side
which will cause loss of control of vehicle and trailer. Consider the following items when computing the
Failure to load trailers heavier in front is the cause of weight on the front/rear axles of the vehicle:
many trailer collisions.
• The trailer tongue weight of the trailer.
• The weight of any other type of cargo or equipment
put in or on your vehicle.
• The weight of the driver and all passengers.
STARTING AND OPERATING 533
NOTE: Remember that everything put into or on the
trailer adds to the load on your vehicle. Also, additional
factory-installed options, or authorized dealer-installed
options, must be considered as part of the total load on
your vehicle. Refer to “Tire Safety Information/Tire and
Loading Information Placard” in “Starting and Operating” for further information.
• Then, during the first 500 miles (805 km) that a
trailer is towed, do not drive over 50 mph
(80 km/h) and do not make starts at full throttle.
This helps the engine and other parts of the
vehicle wear in at the heavier loads.
Towing Requirements
To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended.
Perform the maintenance listed in the “Maintenance
Schedule.” Refer to “Maintenance Schedule” for the
proper maintenance intervals. When towing a trailer,
never exceed the GAWR or GCWR ratings.
CAUTION!
WARNING!
• Do not tow a trailer at all during the first 500 miles
(805 km) the new vehicle is driven. The engine,
axle or other parts could be damaged.
Improper towing can lead to a collision. Follow these
guidelines to make your trailer towing as safe as
possible:
(Continued)
CAUTION! (Continued)
(Continued)
5
534 STARTING AND OPERATING
WARNING! (Continued)
WARNING! (Continued)
• Make certain that the load is secured in the trailer
and will not shift during travel. When trailering
cargo that is not fully secured, dynamic load shifts
can occur that may be difficult for the driver to
control. You could lose control of your vehicle and
have a collision.
• When hauling cargo or towing a trailer, do not
overload your vehicle or trailer. Overloading can
cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering,
suspension, chassis structure or tires.
• Safety chains must always be used between your
vehicle and trailer. Always connect the chains to
the hook retainers of the vehicle hitch. Cross the
chains under the trailer tongue and allow enough
slack for turning corners.
• Vehicles with trailers should not be parked on a
grade. When parking, apply the parking brake on
the tow vehicle. Put the tow vehicle transmission
in PARK. For four-wheel drive vehicles, make sure
the transfer case is not in NEUTRAL. Always,
block or ⴖchockⴖ the trailer wheels.
• GCWR must not be exceeded.
• Total weight must be distributed between the tow
vehicle and the trailer such that the following four
ratings are not exceeded:
1. GVWR
2. GTW
3. GAWR
4. Trailer tongue weight rating for the trailer hitch
utilized (This requirement may limit the ability to
always achieve the 10% to 15% range of tongue
weight as a percentage of total trailer weight).
(Continued)
STARTING AND OPERATING 535
Towing Requirements – Tires
− Do not attempt to tow a trailer while using a compact
spare tire.
replacement procedures. Replacing tires with a higher
load carrying capacity will not increase the vehicle’s
GVWR and GAWR limits.
Towing Requirements – Trailer Brakes
− Proper tire inflation pressures are essential to the safe
and satisfactory operation of your vehicle. Refer to − Do not interconnect the hydraulic brake system or
vacuum system of your vehicle with that of the trailer.
“Tires – General Information” in “Starting and Operating” for proper tire inflation procedures.
This could cause inadequate braking and possible
personal injury.
− Check the trailer tires for proper tire inflation pres− An electronically-actuated trailer brake controller is
sures before trailer usage.
required when towing a trailer with electronically− Check for signs of tire wear or visible tire damage
actuated brakes. When towing a trailer equipped with
before towing a trailer. Refer to “Tires – General
a hydraulic surge-actuated brake system, an electronic
Information” in “Starting and Operating” for proper
brake controller is not required.
inspection procedure.
− Trailer brakes are recommended for trailers over
− When replacing tires, refer to “Tires – General Infor1,000 lbs (454 kg), and required for trailers in excess of
mation” in “Starting and Operating” for proper tire
2,000 lbs (907 kg).
5
536 STARTING AND OPERATING
CAUTION!
WARNING! (Continued)
If the trailer weighs more than 1,000 lbs (454 kg)
loaded, it should have its own brakes and they
should be of adequate capacity. Failure to do this
could lead to accelerated brake lining wear, higher
brake pedal effort, and longer stopping distances.
• Towing any trailer will increase your stopping
distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result
in a collision.
WARNING!
• Do not connect trailer brakes to your vehicle’s
hydraulic brake lines. It can overload your brake
system and cause it to fail. You might not have
brakes when you need them and could have a
collision.
Towing Requirements – Trailer Lights And Wiring
Whenever you pull a trailer, regardless of the trailer size,
stop lights and turn signals on the trailer are required for
motoring safety.
The Trailer Tow Package includes both a seven-pin and a
four-pin connector at the rear of the vehicle.
The electrical connections are all complete to the vehicle
(Continued) but you must mate the harness to a trailer connector.
Refer to the following illustrations.
STARTING AND OPERATING 537
5
Four-Pin Connector
1 — Female Pins
2 — Male Pin
3 — Ground
4 — Park
5 — Left Stop/Turn
6 — Right Stop/Turn
Seven-Pin Connector
1
2
3
4
—
—
—
—
Battery
Backup Lamps
Right Stop/Turn
Electric Brakes
5 — Ground
6 — Left Stop/Turn
7 — Running Lamps
538 STARTING AND OPERATING
Towing Tips
Before setting out on a trip, practice turning, stopping
and backing the trailer in an area away from heavy
traffic.
The transmission fluid and filter should be changed if
you REGULARLY tow a trailer for more than 45 minutes
of continuous operation. Refer to “Maintenance Schedule” for the proper maintenance intervals.
Automatic Transmission
The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, the
TOW/HAUL mode (if equipped), or a lower gear range,
should be selected.
NOTE: Check the transmission fluid level before towing
(5.7L engine).
Electronic Speed Control – If Equipped
− Do not use in hilly terrain or with heavy loads.
NOTE: Using the TOW/HAUL mode (if equipped) or − When using the speed control, if you experience speed
drops greater than 10 mph (16 km/h), disengage until
selecting a lower gear range (using the Electronic Range
you can get back to cruising speed.
Select (ERS) feature) while operating the vehicle under
heavy operating conditions, will improve performance
− Use speed control in flat terrain and with light loads to
and extend transmission life by reducing excessive shiftmaximize fuel efficiency.
ing and heat buildup. This action will also provide better
engine braking.
STARTING AND OPERATING 539
Cooling System
SNOW PLOW
To reduce potential for engine and transmission over- Snow plows, winches, and other aftermarket equipment
heating, take the following actions:
should not be added to the front end of your vehicle. The
airbag crash sensors may be affected by the change in the
− City Driving
front end structure. The airbags could deploy unexpectWhen stopped for short periods of time, shift the transedly or could fail to deploy during a collision.
mission into NEUTRAL and increase engine idle speed.
− Highway Driving
Reduce speed.
− Air Conditioning
Turn off temporarily.
WARNING!
Do not add a snow plow, winches, or any other
aftermarket equipment to the front of your vehicle.
This could adversely affect the functioning of the
airbag system and you could be injured.
5
540 STARTING AND OPERATING
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)
Towing This Vehicle Behind Another Vehicle
Towing Condition
Wheels OFF the
Ground
Rear-Wheel Drive
Models
All-Wheel Drive Models
See Instructions
Flat Tow
Dolly Tow
On Trailer
NONE
NOT ALLOWED
Front
Rear
ALL
NOT ALLOWED
OK
OK
• Transmission in PARK
• Transfer case in NEUTRAL (N)
• Tow in forward direction
NOT ALLOWED
NOT ALLOWED
OK
STARTING AND OPERATING 541
6. Install a suitable clamping device, designed for towRecreational Towing – Rear-Wheel Drive Models
DO NOT flat tow this vehicle. Damage to the drivetrain ing, to secure the front wheels in the straight position.
will result.
Recreational towing (for two-wheel drive models) is
allowed ONLY if the rear wheels are OFF the ground.
This may be accomplished using a tow dolly or vehicle
trailer. If using a tow dolly, follow this procedure:
1. Properly secure the dolly to the tow vehicle, following
the dolly manufacturer’s instructions.
CAUTION!
Towing with the rear wheels on the ground will
cause severe transmission damage. Damage from
improper towing is not covered under the New
Vehicle Limited Warranty.
Recreational Towing – All-Wheel Drive Models
2. Drive the rear wheels onto the tow dolly.
(Single-Speed Transfer Case)
Recreational towing is not allowed. These models do
3. Firmly set the parking brake. Shift the transmission
not have a NEUTRAL (N) position in the transfer case.
into PARK.
NOTE: This vehicle may be towed on a flatbed or
4. Properly secure the rear wheels to the dolly, following
vehicle trailer provided all four wheels are OFF the
the dolly manufacturer’s instructions.
ground.
5. Remove the key fob from the ignition switch.
5
542 STARTING AND OPERATING
CAUTION!
CAUTION!
Towing this vehicle in violation of the above requirements can cause severe transmission and/or transfer
case damage. Damage from improper towing is not
covered under the New Vehicle Limited Warranty.
• Front or rear wheel lifts should not be used.
Internal damage to the transmission or transfer
case will occur if a front or rear wheel lift is used
when recreational towing.
• Tow only in the forward direction. Towing this
vehicle backwards can cause severe damage to the
transfer case.
• The transmission must be placed in the PARK
position for recreational towing.
• Before recreational towing, perform the procedure
outlined under “Shifting Into NEUTRAL (N)” to
be certain that the transfer case is fully in NEUTRAL (N). Otherwise, internal damage will result.
Recreational Towing – All-Wheel Drive Models
(Two-Speed Transfer Case)
The transfer case must be shifted into NEUTRAL (N) and
the transmission must be placed in PARK for recreational
towing. The NEUTRAL (N) selection button is adjacent to
the transfer case selector switch. Shifts into and out of
transfer case NEUTRAL (N) can take place with the
selector switch in any mode position.
(Continued)
STARTING AND OPERATING 543
CAUTION! (Continued)
• Failure to follow these procedures can cause severe transmission and/or transfer case damage.
Damage from improper towing is not covered
under the New Vehicle Limited Warranty.
• Do not use a bumper-mounted clamp-on tow bar
on your vehicle. The bumper face bar will be
damaged.
Shifting Into NEUTRAL (N)
Use the following procedure to prepare your vehicle for
recreational towing:
WARNING!
You or others could be injured if you leave the
vehicle unattended with the transfer case in the
NEUTRAL (N) position without first fully engaging
the parking brake. The transfer case NEUTRAL (N)
position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle
to move, even if the transmission is in PARK. The
parking brake should always be applied when the
driver is not in the vehicle.
5
544 STARTING AND OPERATING
CAUTION!
It is necessary to follow these steps to be certain that
the transfer case is fully in NEUTRAL (N) before
recreational towing to prevent damage to internal
parts.
4. Turn the ignition switch to the ON/RUN position, but
do not start the engine.
5. Press and hold the brake pedal.
6. Shift the transmission into NEUTRAL.
7. Using the point of a ballpoint pen or similar object,
press and hold the recessed transfer case NEUTRAL (N)
1. Bring the vehicle to a complete stop and shift the
button (located by the selector switch) for four seconds,
transmission into PARK.
until the light behind the N symbol starts to blink,
indicating shift in progress. The light will stop blinking
2. Turn OFF the engine.
(stay on solid) when the shift to NEUTRAL is complete.
3. For vehicles with Keyless Enter-N-Go, remove the
Keyless Enter-N-Go button and use the key fob to
complete this procedure. Refer to “Starting Procedures/
Keyless Enter-N-Go” in “Starting and Operating” for
further information.
STARTING AND OPERATING 545
11. Release the brake pedal for five seconds and ensure
that there is no vehicle movement.
12. Repeat steps 9 and 10 with transmission in DRIVE.
13. Turn OFF the engine.
14. Firmly apply the parking brake.
15. Shift the transmission into PARK.
CAUTION!
NEUTRAL Switch
8. After the shift is completed and the NEUTRAL (N)
light stays on, release the NEUTRAL (N) button.
9. Start the engine.
10. Shift the transmission into REVERSE.
Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in
NEUTRAL (N) and the engine running. With the
transfer case in NEUTRAL (N), ensure that the engine is OFF prior to shifting the transmission into
PARK.
16. Remove the key fob from the ignition switch.
5
546 STARTING AND OPERATING
17. Attach the vehicle to the tow vehicle using a suitable
tow bar.
• A flashing NEUTRAL (N) indicator light indicates that
shift requirements have not been met.
18. Release the parking brake.
Shifting Out Of NEUTRAL (N)
Use the following procedure to prepare your vehicle for
normal usage:
NOTE:
• Steps 1 through 6 are requirements that must be met
prior to pressing the NEUTRAL (N) button, and must
continue to be met until the shift has been completed.
If any of these requirements are not met prior to
pressing the NEUTRAL (N) button or are no longer
met during the shift, the NEUTRAL (N) indicator light
will flash continuously until all requirements are met
or until the NEUTRAL (N) button is released.
• The ignition switch must be in the ON/RUN position
for a shift to take place and for the position indicator
lights to be operable. If the ignition switch is not in the
ON/RUN position, the shift will not take place and no
position indicator lights will be on or flashing.
1. Bring the vehicle to a complete stop, leaving it connected to the tow vehicle.
2. Firmly apply the parking brake.
3. Turn the ignition switch to the ON/RUN position, but
do not start the engine.
4. Press and hold the brake pedal.
5. Shift the transmission into NEUTRAL.
6. Using the point of a ballpoint pen or similar object,
press and hold the recessed transfer case NEUTRAL (N)
button (located by the selector switch) for one second.
STARTING AND OPERATING 547
NOTE: When shifting out of transfer case NEUTRAL
(N), turning the engine OFF may be required to avoid
gear clash.
9. Shift transmission into PARK.
10. Release the brake pedal.
11. Disconnect vehicle from the tow vehicle.
12. Start the engine.
13. Press and hold the brake pedal.
14. Release the parking brake.
NEUTRAL Switch
15. Shift the transmission into DRIVE, release the brake
7. After the NEUTRAL (N) indicator light turns off,
pedal, and check that the vehicle operates normally.
release the NEUTRAL (N) button.
16. The Keyless Enter-N-Go button (if equipped) may
8. After the NEUTRAL (N) button has been released, the
now be reinstalled if desired. Refer to “Starting
transfer case will shift to the position identified by the
Procedures/Keyless Enter-N-Go” in “Starting and Operselector switch.
ating” for further information.
5
548 STARTING AND OPERATING
NOTE:
• The ignition switch must be in the ON/RUN position
• Steps 1 through 5 are requirements that must be met
for a transfer case shift to take place and for the
prior to pressing the transfer case NEUTRAL (N)
position indicator lights to be operable. If the ignition
button and must continue to be met until the shift has
switch is not in the ON/RUN position, the shift will
been completed. If any of these requirements are not
not take place and no position indicator lights will be
met prior to pressing the NEUTRAL (N) button, or are
on or flashing.
no longer met during the shift, the NEUTRAL (N)
• A flashing NEUTRAL (N) position indicator light
indicator light will flash continuously until all requireindicates that shift requirements have not been met.
ments are met or until the NEUTRAL (N) button is
released.
WHAT TO DO IN EMERGENCIES
CONTENTS
䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . 551
▫ Road Tire Installation . . . . . . . . . . . . . . . . . 566
䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 551 䡵 Jump-Starting . . . . . . . . . . . . . . . . . . . . . . . . 567
䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 552
▫ Preparations For Jump-Start . . . . . . . . . . . . . 568
▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 553
▫ Jump-Starting Procedure . . . . . . . . . . . . . . . 569
▫ Spare Tire Stowage . . . . . . . . . . . . . . . . . . . 554 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 571
▫ Spare Tire Removal . . . . . . . . . . . . . . . . . . . 555 䡵 Emergency Tow Hooks — If Equipped . . . . . . 573
▫ Preparations For Jacking . . . . . . . . . . . . . . . 558 䡵 Shift Lever Override . . . . . . . . . . . . . . . . . . . 573
▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 559
6
550 WHAT TO DO IN EMERGENCIES
䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 574
▫ Rear-Wheel Drive Models . . . . . . . . . . . . . . 576
▫ Towing Without The Ignition Key Fob . . . . . 576
▫ All-Wheel Drive Models . . . . . . . . . . . . . . . 577
WHAT TO DO IN EMERGENCIES 551
HAZARD WARNING FLASHERS
IF YOUR ENGINE OVERHEATS
The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the
switch bank just above the climate controls.
potential for overheating by taking the appropriate action.
Press the switch to turn on the Hazard Warning • On the highways — slow down.
flasher. When the switch is activated, all directional
• In city traffic — while stopped, place the transmission
turn signals will flash on and off to warn oncoming
in NEUTRAL, but do not increase the engine idle
traffic of an emergency. Press the switch a second time to
speed.
turn off the Hazard Warning flashers.
NOTE: There are steps that you can take to slow down
This is an emergency warning system and it should not
an impending overheat condition:
be used when the vehicle is in motion. Use it when your
vehicle is disabled and it is creating a safety hazard for • If your air conditioner (A/C) is on, turn it off. The A/C
system adds heat to the engine cooling system and
other motorists.
turning the A/C off can help remove this heat.
When you must leave the vehicle to seek assistance, the
Hazard Warning flashers will continue to operate even • You can also turn the temperature control to maximum
heat, the mode control to floor and the blower control
though the ignition is placed in the OFF position.
to high. This allows the heater core to act as a
NOTE: With extended use the Hazard Warning flashers
supplement to the radiator and aids in removing heat
may wear down your battery.
from the engine cooling system.
6
552 WHAT TO DO IN EMERGENCIES
CAUTION!
Driving with a hot cooling system could damage
your vehicle. If the temperature gauge reads HOT
(H), pull over and stop the vehicle. Idle the vehicle
with the air conditioner turned off until the pointer
drops back into the normal range. If the pointer
remains on HOT (H), and you hear continuous
chimes, turn the engine off immediately and call for
service.
WARNING!
You or others can be badly burned by hot engine
coolant (antifreeze) or steam from your radiator. If
you see or hear steam coming from under the hood,
do not open the hood until the radiator has had time
to cool. Never try to open a cooling system pressure
cap when the radiator or coolant bottle is hot.
JACKING AND TIRE CHANGING
WARNING!
• Do not attempt to change a tire on the side of the
vehicle close to moving traffic. Pull far enough off
the road to avoid the danger of being hit when
operating the jack or changing the wheel.
• Being under a jacked-up vehicle is dangerous. The
vehicle could slip off the jack and fall on you. You
could be crushed. Never put any part of your body
under a vehicle that is on a jack. If you need to get
under a raised vehicle, take it to a service center
where it can be raised on a lift.
• Never start or run the engine while the vehicle is
on a jack.
(Continued)
WHAT TO DO IN EMERGENCIES 553
WARNING! (Continued)
• The jack is designed to be used as a tool for
changing tires only. The jack should not be used to
lift the vehicle for service purposes. The vehicle
should be jacked on a firm level surface only.
Avoid ice or slippery areas.
Jack Location
The scissor-type jack and tire changing tools are located
in rear cargo area, below the load floor.
6
Jack Storage Location
554 WHAT TO DO IN EMERGENCIES
Rotate the thumb screw on the jack to loosen the assem- the square socket extension to rotate the “spare tire
drive” nut. The nut is located under a plastic cover at the
bly and remove the jack from the bracket.
center-rear of the cargo floor area, just inside the liftgate
opening.
Thumb Screw Location
Spare Tire Stowage
The spare tire is stowed under the rear of the vehicle by
means of a cable winch mechanism. To remove or stow
the spare, use the jack handle/lug wrench connected to
Spare Tire Location
WHAT TO DO IN EMERGENCIES 555
CAUTION!
Do not use power tools to winch the tire up or down.
Impact type tools can damage the winch mechanism.
Spare Tire Removal
1. Remove the jack tools from the bag.
2. Raise the rubber mat and remove the plug from
storage compartment floor.
3. Fit the jack handle extension over the drive nut. Use
the lug wrench handle and extension to completely lower
the spare tire. Keep turning the handle until the winch
stops.
6
Lowering/Raising Spare Tire
556 WHAT TO DO IN EMERGENCIES
4. Slide the tire out from under the vehicle and rotate it 5. Spread the retaining tabs on the plastic plate and pull
vertically behind the rear bumper.
the metal stamping toward you to release it from the
plastic plate.
Spare Tire
Tab Location
WHAT TO DO IN EMERGENCIES 557
6. Slide the metal stamping up the steel extension tube 7. Pinch the three short and two long tubes to remove the
and winch cable. Rotate the metal stamping and push it protective plate from the steel spare wheel.
through the hole in the plastic plate and wheel.
6
Releasing Protective Plate
Sleeve And Cable
558 WHAT TO DO IN EMERGENCIES
Preparations For Jacking
1. Park the vehicle on a firm level surface, away from
traffic.
3. Block the diagonally opposite
wheel.
WARNING!
Do not attempt to change a tire on the side of the
vehicle closest to moving traffic, pull far enough off
the road to avoid being hit when operating the jack
or changing the wheel.
2. Place the transmission in PARK, set the parking brake
and activate the Hazard Warning flashers.
NOTE: Passengers should not remain in the vehicle
when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 559
Jacking Instructions
WARNING! (Continued)
WARNING!
Carefully follow these tire changing warnings to
help prevent personal injury or damage to your
vehicle:
• Always park on a firm, level surface as far from
the edge of the roadway as possible before raising
the vehicle.
• Turn on the Hazard Warning flasher.
• Block the wheel diagonally opposite the wheel to
be raised.
• Set the parking brake firmly and set the automatic
transmission in PARK.
• Never start or run the engine with the vehicle on a
jack.
• Do not let anyone sit in the vehicle when it is on a
jack.
• Do not get under the vehicle when it is on a jack.
• Only use the jack in the positions indicated and
for lifting this vehicle during a tire change.
• If working on or near a roadway, be extremely
careful of motor traffic.
• To assure that spare tires, flat or inflated, are
securely stowed, spares must be stowed with the
valve stem facing the ground.
(Continued)
Jack Warning Label
6
560 WHAT TO DO IN EMERGENCIES
CAUTION!
Do not attempt to raise the vehicle by jacking on
locations other than those indicated in the Jacking
Instructions for this vehicle.
1. Loosen (but do not remove) the wheel lug nuts by
turning them to the left, one turn, while the wheel is still
on the ground.
2. Assemble the jack and jacking tools.
Jack and Tool Assembly
3. For the front axle, place the jack on the body flange
just behind the front tire as indicated by the triangular lift
point symbol on the sill molding. Do not raise the
vehicle until you are sure the jack is fully engaged.
WHAT TO DO IN EMERGENCIES 561
6
Lift Point Symbol On Sill Molding
Front Jacking Location
562 WHAT TO DO IN EMERGENCIES
4. For a rear tire, place the jack in the slot on the rear
tie-down bracket, just forward of the rear tire (as indicated by the triangular lift point symbol on the sill
molding). Do not raise the vehicle until you are sure the
jack is fully engaged.
Rear Jacking Location
5. Raise the vehicle by turning the jack screw clockwise.
Raise the vehicle just enough to remove the flat tire.
Lift Point Symbol On Sill Molding
WHAT TO DO IN EMERGENCIES 563
WARNING!
Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.
6. Remove the lug nuts and wheel.
7. Install the spare wheel/tire on the vehicle and install
the lug nuts with the cone-shaped end toward the wheel.
Lightly tighten the nuts.
CAUTION!
Be sure to mount the spare tire with the valve stem
facing outward. The vehicle could be damaged if the
spare tire is mounted incorrectly.
6
Mounting Spare Tire
WARNING!
To avoid the risk of forcing the vehicle off the jack,
do not fully tighten the wheel nuts until the vehicle
has been lowered. Failure to follow this warning may
result in personal injury.
564 WHAT TO DO IN EMERGENCIES
8. Lower the vehicle by turning the jack screw counterclockwise, and remove the jack and wheel blocks.
9. Finish tightening the lug nuts. Push down on the
wrench while at the end of the handle for increased
leverage. Tighten the lug nuts in a star pattern until each
nut has been tightened twice. The correct wheel nut
tightness is 110 ft lbs (150 N·m). If in doubt about the
correct tightness, have them checked with a torque
wrench by your authorized dealer or at a service station.
10. Remove the small center cap and position the aluminum road wheel behind rear bumper with the “beauty
side” facing rearward.
“Beauty Side”
11. Insert the two long tubes on the plastic protective
plate in the lug holes of the road wheel. Push the end of
the winch’s cable, spring, steel sleeve and stamped cone
shape wheel plate though the road wheel and protective
plate.
WHAT TO DO IN EMERGENCIES 565
6
Installing Winch
Road Wheel Installed In Spare Location
12. Slide the road wheel on the ground using the protec- NOTE: Double check to ensure the tire is snug against
tive plate until it is directly under the winch and between the underbody of the vehicle. Damage to the winch cable
the rear bumper and exhaust system heat shields. Raise may result if the vehicle is driven with the tire loose.
the tire by turn the lug wrench on the winch extension
clockwise until it clicks/ratchets three times to make sure
the cable is tight.
566 WHAT TO DO IN EMERGENCIES
WARNING!
Do not use power tools to winch the tire up or down.
Impact-type tools may damage the winch mechanism.
15. Have the aluminum road wheel and tire repaired as
soon as possible and properly secure the spare tire, jack
and tool kit.
WARNING!
A loose tire or jack, thrown forward in a collision or
13. Lower the jack to the fully closed position. Return the
hard stop could endanger the occupants of the vetools to the proper positions in the tool bag. Fold the flap
hicle. Always stow the jack parts and the spare tire in
on the tool bag under the tools and roll the tools in the
the places provided.
bag underneath the others. Use the Velcro straps to
secure the tool bag to the jack with the lug wrench on the
Road Tire Installation
forward side of the jack. Expand the jack on the bracket
by turning the thumb screw clockwise until it is tight to 1. Mount the road tire on the axle.
prevent rattles.
2. Install the remaining lug nuts with the cone shaped
14. Reinstall the plastic plug into the floor of the cargo end of the nut toward the wheel. Lightly tighten the lug
area. Roll up and store the Jack, Tool Kit and Tire nuts.
Changing Instructions. Reinstall the cover for the jack in
the rear storage bin.
WHAT TO DO IN EMERGENCIES 567
WARNING!
To avoid the risk of forcing the vehicle off the jack,
do not tighten the lug nuts fully until the vehicle is
lowered to the ground.
JUMP-STARTING
If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in
another vehicle or by using a portable battery booster
pack. Jump-starting can be dangerous if done improperly
so please follow the procedures in this section carefully.
3. Lower the vehicle to the ground by turning the jack
NOTE: When using a portable battery booster pack
handle counterclockwise.
follow the manufacturer’s operating instructions and
4. Finish tightening the lug nuts. Push down on the precautions.
wrench while at the end of the handle for increased
CAUTION!
leverage. Tighten the lug nuts in a star pattern until each
nut has been tightened twice. The correct tightness of
Do not use a portable battery booster pack or any
each lug nut is 110 ft/lbs (150 N·m). If in doubt about the
other booster source with a system voltage greater
correct tightness, have them checked with a torque
than 12 Volts or damage to the battery, starter motor,
wrench by your authorized dealer or service station.
alternator or electrical system may occur.
5. After 25 miles (40 km) check the lug nut torque with a
torque wrench to ensure that all lug nuts are properly
seated against the wheel.
6
568 WHAT TO DO IN EMERGENCIES
WARNING!
Do not attempt jump-starting if the battery is frozen.
It could rupture or explode and cause personal injury.
Preparations For Jump-Start
The battery in your vehicle is located under the passenger’s front seat. There are remote locations located under
the hood to assist in jump-starting.
Remote Battery Posts
1 — Remote Positive (+) Post (covered with protective cap)
2 — Remote Negative (-) Post
WHAT TO DO IN EMERGENCIES 569
WARNING!
• Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the
ignition switch is on. You can be injured by
moving fan blades.
• Remove any metal jewelry such as watch bands or
bracelets that might make an inadvertent electrical
contact. You could be seriously injured.
• Batteries contain sulfuric acid that can burn your
skin or eyes and generate hydrogen gas which is
flammable and explosive. Keep open flames or
sparks away from the battery.
1. Set the parking brake, shift the automatic transmission
into PARK and turn the ignition to LOCK.
2. Turn off the heater, radio, and all unnecessary electrical accessories.
3. Remove the protective cover over the remote positive
(+) battery post. Pull upward on the cover to remove it.
4. If using another vehicle to jump-start the battery, park
the vehicle within the jumper cables reach, set the
parking brake and make sure the ignition is OFF.
WARNING!
Do not allow vehicles to touch each other as this
could establish a ground connection and personal
injury could result.
Jump-Starting Procedure
WARNING!
Failure to follow this procedure could result in personal
injury or property damage due to battery explosion.
6
570 WHAT TO DO IN EMERGENCIES
CAUTION!
WARNING!
Failure to follow these procedures could result in
damage to the charging system of the booster vehicle
or the discharged vehicle.
Do not connect the cable to the negative post (-) of the
discharged battery. The resulting electrical spark
could cause the battery to explode and could result in
personal injury.
1. Connect the positive (+) end of the jumper cable to the
remote positive (+) post of the discharged vehicle.
5. Start the engine in the vehicle that has the booster
battery, let the engine idle a few minutes, and then start
2. Connect the opposite end of the positive (+) jumper
the engine in the vehicle with the discharged battery.
cable to the positive (+) post of the booster battery.
Once the engine is started, remove the jumper cables in
3. Connect the negative end (-) of the jumper cable to the
the reverse sequence:
negative (-) post of the booster battery.
6. Disconnect the negative (-) jumper cable from the
4. Connect the opposite end of the negative (-) jumper
remote negative (-) post of the discharged vehicle.
cable to the remote negative (-) post of the vehicle with
the discharged battery.
WHAT TO DO IN EMERGENCIES 571
7. Disconnect the negative end (-) of the jumper cable
from the negative (-) post of the booster battery.
8. Disconnect the opposite end of the positive (+) jumper
cable from the positive (+) post of the booster battery.
9. Disconnect the positive (+) end of the jumper cable
from the remote positive (+) post of the discharged
vehicle.
CAUTION!
Accessories that can be plugged into the vehicle
power outlets draw power from the vehicle’s battery,
even when not in use (i.e., cellular phones, etc.).
Eventually, if plugged in long enough, the vehicle’s
battery will discharge sufficiently to degrade battery
life and/or prevent the engine from starting.
10. Reinstall the protective cover over the remote posiFREEING A STUCK VEHICLE
tive (+) battery post of the discharged vehicle.
If the vehicle becomes stuck in snow, sand or mud, it can
If frequent jump-starting is required to start your vehicle often be moved by a rocking motion. Move the shift lever
you should have the battery and charging system in- rhythmically between DRIVE and REVERSE while apspected at your authorized dealer.
plying slight pressure to the accelerator. In general, the
least amount of accelerator pedal pressure to maintain
the rocking motion without spinning the wheels or racing
the engine is most effective.
6
572 WHAT TO DO IN EMERGENCIES
CAUTION!
CAUTION! (Continued)
Racing the engine or spinning the wheels may lead to
transmission overheating and failure. Allow the engine to idle with the shift lever in NEUTRAL for at
least one minute after every five rocking-motion
cycles. This will minimize overheating and reduce
the risk of transmission failure during prolonged
efforts to free a stuck vehicle.
CAUTION!
• When “rocking” a stuck vehicle by moving between DRIVE and REVERSE, do not spin the
wheels faster than 15 mph (24 km/h), or drivetrain
damage may result.
(Continued)
• Revving the engine or spinning the wheels too fast
may lead to transmission overheating and failure.
It can also damage the tires. Do not spin the
wheels above 30 mph (48 km/h) while in gear (no
transmission shifting occurring).
WARNING!
Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or
even failure, of the axle and tires. A tire could
explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for
longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near
a spinning wheel, no matter what the speed.
WHAT TO DO IN EMERGENCIES 573
EMERGENCY TOW HOOKS — IF EQUIPPED
If your vehicle is equipped with tow hooks, there will be
one in the rear and two mounted on the front of the
vehicle. The rear hook will be located on the driver’s side
of the vehicle.
CAUTION!
Tow hooks are for emergency use only, to rescue a
vehicle stranded off road. Do not use tow hooks for
tow truck hookup or highway towing. You could
damage your vehicle.
NOTE: For off-road recovery, it is recommended to use
both of the front tow hooks to minimize the risk of
SHIFT LEVER OVERRIDE
damage to the vehicle.
If a malfunction occurs and the shift lever cannot be
moved out of the PARK position, you can use the
WARNING!
following procedure to temporarily move the shift lever:
• Chains are not recommended for freeing a stuck
vehicle. Chains may break, causing serious injury 1. If the engine is running, press the START/STOP
button to turn it off. Do not start the engine (engine OFF).
or death.
• Stand clear of vehicles when pulling with tow
hooks. Tow straps may become disengaged, causing serious injury.
2. Firmly apply the parking brake.
3. Remove the rubber liner from the cupholder (located
next to the shifter on the center console).
6
574 WHAT TO DO IN EMERGENCIES
4. Using a screwdriver or similar tool, carefully remove 6. Using the screwdriver or similar tool, reach into the
the shift lever override access cover, located on the opening and press and hold the shift lever override
down.
bottom of the cupholder.
7. Move the shift lever to the NEUTRAL position.
8. The vehicle may then be started in NEUTRAL.
9. Reinstall the shift lever override access cover and
rubber liner.
Shift Lever Override Access Cover
5. Press and maintain firm pressure on the brake pedal.
TOWING A DISABLED VEHICLE
This section describes procedures for towing a disabled
vehicle using a commercial wrecker service. If the transmission and drivetrain are operable, disabled vehicles
may also be towed as described under “Recreational
Towing” in the “Starting And Operating” section.
WHAT TO DO IN EMERGENCIES 575
Towing Condition
Flat Tow
Wheel Lift or
Dolly Tow
Flatbed
Wheels OFF
the Ground
NONE
Front
Rear
ALL
RWD MODELS
AWD MODELS
If transmission is operable:
See instructions in “Recreational Towing” under “Starting and Operating”
• Transmission in NEUTRAL
• Transmission in PARK
• 30 mph (48 km/h)max speed
• Transfer Case in NEUTRAL
• 15 miles (24 km) max distance
• Tow in forward direction
NOT ALLOWED
NOT ALLOWED
BEST METHOD
OK
BEST METHOD
Proper towing or lifting equipment is required to prevent
damage to your vehicle. Use only tow bars and other
equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is
mandatory. Attach a tow bar or other towing device to
main structural members of the vehicle, not to bumpers
or associated brackets. State and local laws applying to
vehicles under tow must be observed.
If you must use the accessories (wipers, defrosters, etc.)
while being towed, the ignition must be in the ON/RUN
position, not the ACC position.
6
576 WHAT TO DO IN EMERGENCIES
If the vehicle’s battery is discharged refer to “Shift Lever Rear-Wheel Drive Models
Override” in “What To Do In Emergencies” for instruc- The manufacturer recommends towing your vehicle with
tions on shifting the automatic transmission out of the all four wheels OFF the ground using a flatbed.
PARK position for towing.
If flatbed equipment is not available, and the transmission is operable, the vehicle may be towed (with rear
CAUTION!
wheels on the ground) with the transmission in NEUDo not attempt to use sling type equipment when TRAL. Speed must not exceed 30 mph (48 km/h) and the
towing. When securing the vehicle to a flat bed truck, distance must not exceed 15 miles (24 km).
do not attach to front or rear suspension components.
CAUTION!
Damage to your vehicle may result from improper
towing.
Towing faster than 30 mph (48 km/h) or farther than
15 miles (24 km) with rear wheels on the ground can
Towing Without The Ignition Key Fob
cause severe damage to the transmission. Such damSpecial care must be taken when the vehicle is towed
age is not covered by the New Vehicle Limited
with the ignition in the LOCK/OFF position. The only
Warranty.
approved method of towing without the ignition key is
with a flatbed truck. Proper towing equipment is necessary to prevent damage to the vehicle.
WHAT TO DO IN EMERGENCIES 577
If the transmission is not operable, or the vehicle must be
towed faster than 30 mph (48 km/h) or farther than
15 miles (24 km), tow with the rear wheels OFF the
ground. Acceptable methods are to tow the vehicle on a
flatbed, or with the front wheels raised and the rear
wheels on a towing dolly, or (when using a suitable
steering wheel stabilizer to hold the front wheels in the
straight position) with the rear wheels raised and the
front wheels on the ground.
wheels on the ground), IF the transfer case is in NEUTRAL and the transmission is in PARK. Refer to “Recreational Towing” in “Starting and Operating” for detailed
instructions.
All-Wheel Drive Models
The manufacturer recommends towing with all wheels
OFF the ground. Acceptable methods are to tow the
vehicle on a flatbed or with one end of vehicle raised and
the opposite end on a towing dolly.
• Front or rear wheel lifts should not be used.
Internal damage to the transmission or transfer
case will occur if a front or rear wheel lift is used
when towing.
• Failure to follow these towing methods can cause
severe damage to the transmission and/or transfer
case. Such damage is not covered by the New
Vehicle Limited Warranty.
If flatbed equipment is not available, and the transfer
case is operable, the vehicles with a two-speed transfer
case may be towed (in the forward direction, with ALL
Vehicles equipped with a single-speed transfer case have
no NEUTRAL position, and therefore must be towed will
all four wheels OFF the ground.
CAUTION!
6
MAINTAINING YOUR VEHICLE
CONTENTS
䡵 Engine Compartment — 3.6L . . . . . . . . . . . . . 581
▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 590
䡵 Engine Compartment — 5.7L . . . . . . . . . . . . . 582
▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 590
䡵 Onboard Diagnostic System — OBD II . . . . . . 583
▫ Maintenance-Free Battery . . . . . . . . . . . . . . 591
▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 583
▫ Air Conditioner Maintenance . . . . . . . . . . . . 593
䡵 Emissions Inspection And Maintenance
Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584
▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . 595
䡵 Replacement Parts . . . . . . . . . . . . . . . . . . . . . 585
䡵 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . 586
䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 586
▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 587
▫ Windshield Wiper Blades . . . . . . . . . . . . . . . 596
▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 598
▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 599
▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 601
7
580 MAINTAINING YOUR VEHICLE
▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 607
▫ Halogen Headlamps – If Equipped . . . . . . . . 627
▫ Front/Rear Axle Fluid . . . . . . . . . . . . . . . . . 609
▫ Front Turn Signal . . . . . . . . . . . . . . . . . . . . 628
▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 610
▫ Front Fog Lamps . . . . . . . . . . . . . . . . . . . . 628
▫ Automatic Transmission . . . . . . . . . . . . . . . 611
▫ Rear Tail, Stop, Turn Signal, And Backup
Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630
▫ Appearance Care And Protection From
Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 614
䡵 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 620
▫ Totally Integrated Power Module . . . . . . . . . 620
䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 625
䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . 626
䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 627
▫ High Intensity Discharge Headlamps (HID) –
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 627
▫ Rear Liftgate Mounted Tail Lamp . . . . . . . . . 630
▫ Center High-Mounted Stop
Lamp (CHMSL) . . . . . . . . . . . . . . . . . . . . . 631
▫ Rear License Lamp . . . . . . . . . . . . . . . . . . . 631
䡵 Fluid Capacities
. . . . . . . . . . . . . . . . . . . . . . 632
䡵 Fluids, Lubricants, And Genuine Parts . . . . . . . 634
▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 634
▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . 635
MAINTAINING YOUR VEHICLE 581
ENGINE COMPARTMENT — 3.6L
7
1
2
3
4
5
—
—
—
—
—
Totally Integrated Power Module (Fuses)
Engine Oil Dipstick
Engine Oil Fill
Brake Fluid Reservoir
Power Steering Fluid Reservoir
6
7
8
9
— Air Cleaner Filter
— Washer Fluid Reservoir
— Coolant Pressure Cap (Radiator)
— Engine Coolant Reservoir
582 MAINTAINING YOUR VEHICLE
ENGINE COMPARTMENT — 5.7L
1
2
3
4
5
— Totally Integrated Power Module (Fuses)
— Automatic Transmission Dipstick
— Engine Oil Fill
— Brake Fluid Reservoir
— Air Cleaner Filter
6
7
8
9
—
—
—
—
Washer Fluid Reservoir
Engine Oil Dipstick
Coolant Pressure Cap (Radiator)
Engine Coolant Reservoir
MAINTAINING YOUR VEHICLE 583
ONBOARD DIAGNOSTIC SYSTEM — OBD II
Your vehicle is equipped with a sophisticated onboard
diagnostic system called OBD II. This system monitors
the performance of the emissions, engine, and automatic
transmission control systems. When these systems are
operating properly, your vehicle will provide excellent
performance and fuel economy, as well as engine emissions well within current government regulations.
CAUTION!
• Prolonged driving with the MIL on could cause
further damage to the emission control system. It
could also affect fuel economy and drivability. The
vehicle must be serviced before any emissions
tests can be performed.
• If the MIL is flashing while the engine is running,
severe catalytic converter damage and power loss
will soon occur. Immediate service is required.
If any of these systems require service, the OBD II system
will turn on the “Malfunction Indicator Light” (MIL). It
will also store diagnostic codes and other information to
assist your service technician in making repairs. Al- Loose Fuel Filler Cap Message
If the vehicle diagnostic system determines
though your vehicle will usually be drivable and not
that the fuel filler cap is loose, improperly
need towing, see your authorized dealer for service as
installed, or damaged, a loose gascap indicator
soon as possible.
will display in the EVIC telltale display area.
Refer to “Electronic Vehicle Information Center (EVIC)”
in “Understanding Your Instrument Panel” for further
information. Tighten the fuel filler cap properly and press
7
584 MAINTAINING YOUR VEHICLE
the SELECT button to turn off the message. If the Normally, the OBD II system will be ready. The OBD II
problem continues, the message will appear the next time system may not be ready if your vehicle was recently
serviced, recently had a dead battery or a battery replacethe vehicle is started.
ment. If the OBD II system should be determined not
A loose, improperly installed, or damaged fuel filler cap
ready for the I/M test, your vehicle may fail the test.
may also turn on the Malfunction Indicator Light (MIL).
Your vehicle has a simple ignition key-actuated test,
EMISSIONS INSPECTION AND MAINTENANCE
which you can use prior to going to the test station. To
PROGRAMS
check if your vehicle’s OBD II system is ready, you must
In some localities, it may be a legal requirement to pass do the following:
an inspection of your vehicle’s emissions control system.
1. Turn the ignition switch to the ON position, but do not
Failure to pass could prevent vehicle registration.
crank or start the engine.
For states that require an Inspection and Maintenance (I/M), this check verifies the “Malfunction 2. If you crank or start the engine, you will have to start
Indicator Light (MIL)” is functioning and is not this test over.
on when the engine is running, and that the OBD II 3. As soon as you turn the ignition switch to the ON
system is ready for testing.
position, you will see the MIL symbol come on as part of
a normal bulb check.
MAINTAINING YOUR VEHICLE 585
4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is
happen:
ready or not, if the MIL is illuminated during normal
vehicle operation you should have your vehicle serviced
a. The MIL will flash for about 10 seconds and then
before going to the I/M station. The I/M station can fail
return to being fully illuminated until you turn OFF
your vehicle because the MIL is on with the engine
the ignition or start the engine. This means that your
running.
vehicle’s OBD II system is not ready and you should
not proceed to the I/M station.
REPLACEMENT PARTS
b. The MIL will not flash at all and will remain fully Use of genuine MOPAR威 parts for normal/scheduled
illuminated until you turn OFF the ignition or start the maintenance and repairs is highly recommended to enengine. This means that your vehicle’s OBD II system sure the designed performance. Damage or failures
caused by the use of non-MOPAR威 parts for maintenance
is ready and you can proceed to the I/M station.
and repairs will not be covered by the manufacturer’s
If your OBD II system is not ready, you should see your warranty.
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your
vehicle as you normally would in order for your OBD II
system to update. A recheck with the above test routine
may then indicate that the system is now ready.
7
586 MAINTAINING YOUR VEHICLE
DEALER SERVICE
Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service
operations in an expert manner. Service Manuals are
available which include detailed service information for
your vehicle. Refer to these Service Manuals before
attempting any procedure yourself.
NOTE: Intentional tampering with emissions control
systems may void your warranty and could result in civil
penalties being assessed against you.
WARNING!
You can be badly injured working on or around a
motor vehicle. Only do service work for which you
have the knowledge and the proper equipment. If
you have any doubt about your ability to perform a
service job, take your vehicle to a competent mechanic.
MAINTENANCE PROCEDURES
The pages that follow contain the required maintenance
services determined by the engineers who designed your
vehicle.
Besides those maintenance items specified in the fixed
maintenance schedule, there are other components which
may require servicing or replacement in the future.
CAUTION!
• Failure to properly maintain your vehicle or perform repairs and service when necessary could
result in more costly repairs, damage to other
components or negatively impact vehicle performance. Immediately have potential malfunctions
examined by an authorized Chrysler Group LLC
dealership or qualified repair center.
(Continued)
MAINTAINING YOUR VEHICLE 587
CAUTION! (Continued)
• Your vehicle has been built with improved fluids
that protect the performance and durability of
your vehicle and also allow extended maintenance
intervals. Do not use chemical flushes in these
components as the chemicals can damage your
engine, transmission, power steering or air conditioning. Such damage is not covered by the New
Vehicle Limited Warranty. If a flush is needed
because of component malfunction, use only the
specified fluid for the flushing procedure.
Engine Oil
Checking Oil Level
To assure proper engine lubrication, the engine oil must
be maintained at the correct level. Check the oil level at
regular intervals, such as every fuel stop. The best time to
check the engine oil level is about five minutes after a
fully warmed engine is shut off, or before starting the
engine after it has sat overnight.
Checking the oil while the vehicle is on level ground will
improve the accuracy of the oil level readings. Maintain
the oil level in the SAFE level range. Adding 1 U.S. Quart
(0.95L) of oil when the level is at the bottom of the SAFE
range will result in the level being at the top of the SAFE
range.
CAUTION!
Overfilling or underfilling the crankcase will cause
aeration or loss of oil pressure. This could damage
your engine.
7
588 MAINTAINING YOUR VEHICLE
Change Engine Oil
American Petroleum Institute (API) Engine Oil
The oil change indicator system will remind you that it is Identification Symbol
This symbol means that the oil has
time to take your vehicle in for scheduled maintenance.
been certified by the American
Refer to “Maintenance Schedule” for further information.
Petroleum Institute (API). The
NOTE: Under no circumstances should oil change
manufacturer only recommends
intervals exceed 8,000 miles (13 000 km) or six months,
API Certified engine oils.
whichever occurs first.
Engine Oil Selection
For best performance and maximum protection for all
engines under all types of operating conditions, the
manufacturer recommends engine oils that are API Certified and meet the requirements of Chrysler Material
Standard MS-6395.
CAUTION!
Do not use chemical flushes in your engine oil as the
chemicals can damage your engine. Such damage is
not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 589
Engine Oil Viscosity – 3.6L Engine
SAE 5W-30 engine oil is recommended for all operating
temperatures. This engine oil improves low temperature
starting and vehicle fuel economy.
The engine oil filler cap also shows the recommended
engine oil viscosity for your vehicle. For information on
engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information.
The engine oil filler cap also shows the recommended
engine oil viscosity for your vehicle. For information on
engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information.
NOTE: Vehicles equipped with a 5.7L engine must use
SAE 5W-20 oil. Failure to do so may result in improper
operation of the Multiple Displacement System (MDS).
Refer to “Multi-Displacement System” in “Starting and
Operating” for further information.
Lubricants, which do not have both the engine oil certification mark and the correct SAE viscosity grade num- Lubricants, which do not have both the engine oil certification mark and the correct SAE viscosity grade number, should not be used.
ber, should not be used.
Engine Oil Viscosity – 5.7L Engine
SAE 5W-20 engine oil is recommended for all operating Synthetic Engine Oils
temperatures. This engine oil improves low temperature You may use synthetic engine oils if the recommended oil
starting and vehicle fuel economy.
quality requirements are met, and the recommended
maintenance intervals for oil and filter changes are
followed.
7
590 MAINTAINING YOUR VEHICLE
Materials Added To Engine Oils
Do not add any supplemental materials, other than leak
detection dyes, to your engine oil. Engine oil is an
engineered product and its performance may be impaired by supplemental additives.
Engine Oil Filter
The engine oil filter should be replaced with a new filter
at every oil change.
Engine Oil Filter Selection
The manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The
quality of replacement filters varies considerably. Only
high-quality filters should be used to assure most efficient service. MOPAR威 engine oil filters are high-quality
oil filters and are recommended.
Disposing Of Used Engine Oil And Oil Filters
Care should be taken in disposing of used engine oil and
oil filters from your vehicle. Used oil and oil filters,
indiscriminately discarded, can present a problem to the
environment. Contact your local authorized dealer, service station, or governmental agency for advice on how
Engine Air Cleaner Filter
and where used oil and oil filters can be safely discarded
Refer to the “Maintenance Schedule” for the proper
in your area.
maintenance intervals.
MAINTAINING YOUR VEHICLE 591
WARNING!
The air induction system (air cleaner, hoses, etc) can
provide a measure of protection in the case of engine
backfire. Do not remove the air induction system (air
cleaner, hoses, etc.) unless such removal is necessary
for repair or maintenance. Make sure that no one is
near the engine compartment before starting the
vehicle with the air induction system (air cleaner,
hoses, etc.) removed. Failure to do so can result in
serious personal injury.
Engine Air Cleaner Filter Selection
The quality of replacement engine air cleaner filters
varies considerably. Only high quality filters should be
used to assure most efficient service. MOPAR威 engine
air cleaner filters are a high quality filter and are
recommended.
Maintenance-Free Battery
Your vehicle is equipped with a maintenance-free battery.
You will never have to add water, nor is periodic maintenance required.
WARNING!
• Battery fluid is a corrosive acid solution and can
burn or even blind you. Do not allow battery fluid
to contact your eyes, skin, or clothing. Do not lean
over a battery when attaching clamps. If acid
splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to
“Jump-Starting Procedures” in “What To Do In
Emergencies” for further information.
(Continued)
7
592 MAINTAINING YOUR VEHICLE
WARNING! (Continued)
CAUTION!
• Battery gas is flammable and explosive. Keep
flame or sparks away from the battery. Do not use
a booster battery or any other booster source with
an output greater than 12 Volts. Do not allow cable
clamps to touch each other.
• Battery posts, terminals, and related accessories
contain lead and lead compounds. Wash hands
after handling.
• It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to
the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the
battery case. Cable clamps should be tight on the
terminal posts and free of corrosion.
• If a “fast charger” is used while the battery is in
the vehicle, disconnect both vehicle battery cables
before connecting the charger to the battery. Do
not use a “fast charger” to provide starting voltage.
MAINTAINING YOUR VEHICLE 593
Air Conditioner Maintenance
For best possible performance, your air conditioner
should be checked and serviced by an authorized dealer
at the start of each warm season. This service should
include cleaning of the condenser fins and a performance
test. Drive belt condition should also be checked at this
time.
CAUTION!
Do not use chemical flushes in your air conditioning
system as the chemicals can damage your air conditioning components. Such damage is not covered by
the New Vehicle Limited Warranty.
WARNING!
• Use only refrigerants and compressor lubricants
approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are
flammable and can explode, injuring you. Other
unapproved refrigerants or lubricants can cause
the system to fail, requiring costly repairs. Refer to
Warranty Information Book, located on the DVD,
for further warranty information.
• The air conditioning system contains refrigerant
under high pressure. To avoid risk of personal
injury or damage to the system, adding refrigerant
or any repair requiring lines to be disconnected
should be done by an experienced repairman.
NOTE: Use only manufacturer approved A/C System
Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, and Refrigerants.
7
594 MAINTAINING YOUR VEHICLE
Refrigerant Recovery And Recycling
R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental
Protection Agency (EPA) and is an ozone-saving product.
However, the manufacturer recommends that air conditioning service be performed by authorized dealers or
other service facilities using recovery and recycling
equipment.
The A/C air filter is located in the fresh air inlet behind
the glove box. Perform the following procedure to replace the filter:
1. Open the glove compartment and remove all contents.
2. Push in on the sides of the glove compartment and
lower the door.
3. Pivot the glove compartment downward.
A/C Air Filter
4. Disengage the two retaining tabs that secure the filter
Refer to the “Maintenance Schedule” for the proper
cover to the HVAC housing, and remove the cover.
maintenance intervals.
WARNING!
Do not remove the A/C air filter while the blower is
operating or personal injury may result.
MAINTAINING YOUR VEHICLE 595
CAUTION!
The A/C air filter is identified with an arrow to
indicate airflow direction through the filter. Failure
to properly install the filter will result in the need to
replace it more often.
7. Rotate the glove compartment door back into position.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
tailgate, sliding doors and hood hinges, should be lubriA/C Air Filter Replacement
cated periodically with a lithium based grease, such as
5. Remove the A/C air filter by pulling it straight out of
MOPAR威 Spray White Lube or equivalent to assure
the housing.
quiet, easy operation and to protect against rust and
6. Install the A/C air filter with the arrow on the filter wear. Prior to the application of any lubricant, the parts
pointing toward the floor. When installing the filter cover, concerned should be wiped clean to remove dust and
make sure the retaining tabs fully engage the cover.
grit; after lubricating excess oil and grease should be
removed. Particular attention should also be given to
7
596 MAINTAINING YOUR VEHICLE
hood latching components to ensure proper function. Avoid using the wiper blades to wipe frost or ice from the
When performing other underhood services, the hood windshield. Keep the blade rubber out of contact with
latch, release mechanism and safety catch should be petroleum products such as engine oil, gasoline, etc.
cleaned and lubricated.
NOTE: Life expectancy of wiper blades varies dependThe external lock cylinders should be lubricated twice a ing on geographical area and frequency of use. Poor
year, preferably in the Fall and Spring. Apply a small performance of blades may be present with chattering,
amount of a high quality lubricant, such as MOPAR威 marks, water lines or wet spots. If any of these conditions
Lock Cylinder Lubricant or equivalent directly into the are present, clean the wiper blades or replace as necessary.
lock cylinder.
Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild nonabrasive cleaner to remove accumulations of salt
or road film.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield.
Rear Wiper Blade Removal/Installation
1. Lift the pivot cap on the rear wiper arm upward, this
will allow the rear wiper blade to be raised off of the
liftgate glass.
MAINTAINING YOUR VEHICLE 597
3. Grab the bottom of the wiper blade and rotate it
forward to unsnap the blade pivot pin from the wiper
blade holder.
1 — Wiper Arm
2 — Pivot Cap
NOTE: The rear wiper arm cannot be raised fully
upward unless the pivot cap is raised first.
2. Lift the rear wiper arm upward to raise the wiper
blade off of the liftgate glass.
7
1
2
3
4
—
—
—
—
Wiper Blade
Blade Pivot Pin
Wiper Arm
Wiper Blade Holder
598 MAINTAINING YOUR VEHICLE
4. Install the wiper blade pivot pin into the wiper blade windshield washer solvent only (not radiator antifreeze).
holder at the end of the wiper arm, and firmly press the When refilling the washer fluid reservoir, take some
washer fluid and apply it to a cloth or towel and wipe
wiper blade until it snaps into place.
clean the wiper blades, this will help blade performance.
5. Lower the wiper blade and snap the pivot cap into
To prevent freeze-up of your windshield washer system
place.
in cold weather, select a solution or mixture that meets or
Adding Washer Fluid
exceeds the temperature range of your climate. This
On vehicles equipped with a Electronic Vehicle Informa- rating information can be found on most washer fluid
tion Center (EVIC), the low washer fluid level will be containers.
indicated. When the sensor detects a low fluid level, the
WARNING!
windshield will light on the vehicle graphic outline and
the “WASHER FLUID LOW” message will be displayed.
Commercially available windshield washer solvents
The fluid reservoir for the windshield washers and the are flammable. They could ignite and burn you. Care
rear window washer is shared. The fluid reservoir is must be exercised when filling or working around
located in the engine compartment, be sure to check the the washer solution.
fluid level at regular intervals. Fill the reservoir with
MAINTAINING YOUR VEHICLE 599
Exhaust System
The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
system.
If you notice a change in the sound of the exhaust system;
or if the exhaust fumes can be detected inside the vehicle;
or when the underside or rear of the vehicle is damaged;
have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams
or loose connections could permit exhaust fumes to seep
into the passenger compartment. In addition, inspect the
exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.
WARNING!
• Exhaust gases can injure or kill. They contain
carbon monoxide (CO), which is colorless and
odorless. Breathing it can make you unconscious
and can eventually poison you. To avoid breathing
CO, refer to “Safety Tips/Exhaust Gas” in “Things
To Know Before Starting Your Vehicle” for further
information.
• A hot exhaust system can start a fire if you park
over materials that can burn. Such materials might
be grass or leaves coming into contact with your
exhaust system. Do not park or operate your vehicle in areas where your exhaust system can
contact anything that can burn.
7
600 MAINTAINING YOUR VEHICLE
CAUTION!
• The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the
effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine.
• Damage to the catalytic converter can result if your
vehicle is not kept in proper operating condition.
In the event of engine malfunction, particularly
involving engine misfire or other apparent loss of
performance, have your vehicle serviced promptly.
Continued operation of your vehicle with a severe
malfunction could cause the converter to overheat,
resulting in possible damage to the converter and
vehicle.
Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure
proper catalyst operation and prevent possible catalyst
damage.
NOTE: Intentional tampering with emissions control
systems can result in civil penalties being assessed
against you.
In unusual situations involving grossly malfunctioning
engine operation, a scorching odor may suggest severe
and abnormal catalyst overheating. If this occurs, stop
the vehicle, turn off the engine and allow it to cool.
Service, including a tune-up to manufacturer’s specifications, should be obtained immediately.
MAINTAINING YOUR VEHICLE 601
To minimize the possibility of catalytic converter dam- Cooling System
age:
• Do not shut off the engine or interrupt the ignition,
when the transmission is in gear and the vehicle is in
motion.
• Do not try to start the engine by pushing or towing the
vehicle.
WARNING!
You or others can be badly burned by hot engine
coolant (antifreeze) or steam from your radiator. If
you see or hear steam coming from under the hood,
do not open the hood until the radiator has had time
to cool. Never try to open a cooling system pressure
cap when the radiator or coolant bottle is hot.
• Do not idle the engine with any spark plug wires
disconnected or removed, such as when diagnostic
testing, or for prolonged periods during very rough Engine Coolant Checks
idle or malfunctioning operating conditions.
Check the engine coolant (antifreeze) protection every
12 months (before the onset of freezing weather, where
applicable). If the engine coolant (antifreeze) is dirty or
rusty in appearance, the system should be drained,
flushed and refilled with fresh engine coolant (antifreeze). Check the front of the A/C condenser for any
7
602 MAINTAINING YOUR VEHICLE
accumulation of bugs, leaves, etc. If dirty, clean by gently Cooling System – Drain, Flush, And Refill
spraying water from a garden hose vertically down the If the engine coolant (antifreeze) is dirty and contains a
considerable amount of sediment, clean and flush with
face of the condenser.
reliable cooling system cleaner. Follow with a thorough
Check the engine cooling system hoses for brittle rubber,
rinsing to remove all deposits and chemicals. Properly
cracking, tears, cuts, and tightness of the connection at
dispose of the old engine coolant (antifreeze).
the coolant recovery bottle and radiator. Inspect the
Refer to the “Maintenance Schedule” for the proper
entire system for leaks.
maintenance intervals.
With the engine at normal operating temperature (but
not running), check the cooling system pressure cap for Selection Of Coolant
proper vacuum sealing by draining a small amount of Use only the manufacturer’s recommended engine coolengine coolant (antifreeze) from the radiator drain cock. ant (antifreeze). Refer to “Fluids, Lubricants, and GenuIf the cap is sealing properly, the engine coolant (anti- ine Parts” in “Maintaining Your Vehicle” for further
freeze) will begin to drain from the coolant recovery information.
bottle. DO NOT REMOVE THE COOLANT PRESSURE
CAP WHEN THE COOLING SYSTEM IS HOT.
MAINTAINING YOUR VEHICLE 603
CAUTION!
• Mixing of engine coolant (antifreeze), other than
the specified HOAT engine coolant (antifreeze),
may result in engine damage and may decrease
corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling
system in an emergency, it should be replaced with
the specified engine coolant (antifreeze) as soon as
possible.
• Do not use water alone or alcohol based engine
coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they
may not be compatible with the engine coolant
(antifreeze) and may plug the radiator.
• This vehicle has not been designed for use with
Propylene Glycol-based engine coolant (antifreeze). Use of Propylene Glycol-based engine
coolant (antifreeze) is not recommended.
Adding Coolant
Your vehicle has been built with an improved engine
coolant (antifreeze) that allows extended maintenance
intervals. This engine coolant (antifreeze) can be used up
to 5 Years or 104,000 miles (169 000 km) before replacement. To prevent reducing this extended maintenance
period, it is important that you use the same engine
coolant (antifreeze) throughout the life of your vehicle.
Please review these recommendations for using Hybrid
Organic Additive Technology (HOAT) engine coolant
(antifreeze).
When adding engine coolant (antifreeze):
• The manufacturer recommends using MOPAR威
Antifreeze/ Coolant 5–Year/100,000 Mile Formula
HOAT (Hybrid Organic Additive Technology) or
equivalent.
7
604 MAINTAINING YOUR VEHICLE
• Mix a minimum solution of 50% HOAT engine coolant
(antifreeze) and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below -34°F
(-37°C) are anticipated.
NOTE: Mixing engine coolant (antifreeze) types will
decrease the life of the engine coolant (antifreeze) and
will require more frequent engine coolant (antifreeze)
changes.
• Use only high purity water such as distilled or deionized water when mixing the water/engine coolant
(antifreeze) solution. The use of lower quality water
will reduce the amount of corrosion protection in the
engine cooling system.
Cooling System Pressure Cap
The cap must be fully tightened to prevent loss of engine
coolant (antifreeze), and to ensure that engine coolant
(antifreeze) will return to the radiator from the coolant
recovery tank.
Please note that it is the owner’s responsibility to main- The cap should be inspected and cleaned if there is any
tain the proper level of protection against freezing ac- accumulation of foreign material on the sealing surfaces.
cording to the temperatures occurring in the area where
the vehicle is operated.
MAINTAINING YOUR VEHICLE 605
WARNING!
• The warning words DO NOT OPEN HOT on the
cooling system pressure cap are a safety precaution.
Never add engine coolant (antifreeze) when the
engine is overheated. Do not loosen or remove the
cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent
scalding or injury, do not remove the pressure cap
while the system is hot or under pressure.
• Do not use a pressure cap other than the one
specified for your vehicle. Personal injury or engine damage may result.
rules for your community. To prevent ingestion by animals and children, do not store ethylene glycol-based
engine coolant (antifreeze) in open containers or allow it
to remain in puddles on the ground. If ingested by a child
or pet, seek emergency assistance immediately. Clean up
any ground spills immediately.
Coolant Level
The coolant bottle provides a quick visual method for
determining that the engine coolant (antifreeze) level is
adequate. With the engine idling, and warm to normal
operating temperature, the level of the engine coolant
(antifreeze) in the bottle should be between the ranges
indicated on the bottle.
The radiator normally remains completely full, so there is
Disposal Of Used Engine Coolant
Used ethylene glycol-based engine coolant (antifreeze) is no need to remove the radiator cap, unless checking for
a regulated substance requiring proper disposal. Check engine coolant (antifreeze) freeze point or replacing enwith your local authorities to determine the disposal gine coolant (antifreeze). Advise your service attendant
7
606 MAINTAINING YOUR VEHICLE
of this. As long as the engine operating temperature is If an examination of your engine compartment shows no
satisfactory, the coolant bottle need only be checked once evidence of radiator or hose leaks, the vehicle may be
safely driven. The vapor will soon dissipate.
a month.
When additional engine coolant (antifreeze) is needed to • Do not overfill the coolant recovery bottle.
maintain the proper level, it should be added to the
• Check engine coolant (antifreeze) freeze point in the
coolant bottle. Do not overfill.
radiator and in the coolant recovery bottle. If engine
Points To Remember
coolant (antifreeze) needs to be added, contents of
coolant recovery bottle must also be protected against
NOTE: When the vehicle is stopped after a few miles
freezing.
(kilometers) of operation, you may observe vapor coming
from the front of the engine compartment. This is nor- • If frequent engine coolant (antifreeze) additions are
required, or if the level in the coolant recovery bottle
mally a result of moisture from rain, snow, or high
does not drop when the engine cools, the cooling
humidity accumulating on the radiator and being vaporsystem should be pressure tested for leaks.
ized when the thermostat opens, allowing hot engine
coolant (antifreeze) to enter the radiator.
• Maintain engine coolant (antifreeze) concentration at
50% HOAT engine coolant (antifreeze) (minimum)
and distilled water for proper corrosion protection of
your engine, which contains aluminum components.
MAINTAINING YOUR VEHICLE 607
• Make sure that the radiator and coolant recovery
bottle hoses are not kinked or obstructed.
• Keep the front of the radiator clean. If your vehicle is
equipped with air conditioning, keep the front of the
condenser clean.
WARNING!
Riding the brakes can lead to brake failure and
possibly a collision. Driving with your foot resting or
riding on the brake pedal can result in abnormally
high brake temperatures, excessive lining wear, and
possible brake damage. You would not have your full
braking capacity in an emergency.
• Do not change the thermostat for Summer or Winter
operation. If replacement is ever necessary, install
ONLY the correct type thermostat. Other designs may
result in unsatisfactory cooling performance, poor gas Fluid Level Check – Brake Master Cylinder
mileage, and increased emissions.
The fluid level of the master cylinder should be checked
when performing under the hood service, or immediBrake System
ately if the brake system warning lamp indicates system
In order to assure brake system performance, all brake
failure.
system components should be periodically inspected.
Refer to the “Maintenance Schedule” for the proper The brake master cylinder has a plastic reservoir. On the
maintenance intervals.
outboard side of the reservoir, there is a “MAX” dot and
a “MIN” dot. The fluid level must be kept within these
two dots. Do not add fluid above the MAX mark, because
leakage may occur at the cap.
7
608 MAINTAINING YOUR VEHICLE
With disc brakes, the fluid level can be expected to fall as
the brake linings wear. However, an unexpected drop in
fluid level may be caused by a leak and a system check
should be conducted.
Refer to “Fluids, Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for further information.
WARNING!
• Use only manufacturer’s recommended brake
fluid. Refer to “Fluids, Lubricants, and Genuine
Parts” in “Maintaining Your Vehicle” for further
information. Using the wrong type of brake fluid
can severely damage your brake system and/or
impair its performance. The proper type of brake
fluid for your vehicle is also identified on the
original factory installed hydraulic master cylinder reservoir.
(Continued)
WARNING! (Continued)
• To avoid contamination from foreign matter or
moisture, use only new brake fluid or fluid that
has been in a tightly closed container. Keep the
master cylinder reservoir cap secured at all times.
Brake fluid in a open container absorbs moisture
from the air resulting in a lower boiling point.
This may cause it to boil unexpectedly during hard
or prolonged braking, resulting in sudden brake
failure. This could result in a collision.
• Overfilling the brake fluid reservoir can result in
spilling brake fluid on hot engine parts, causing
the brake fluid to catch fire. Brake fluid can also
damage painted and vinyl surfaces, care should be
taken to avoid its contact with these surfaces.
(Continued)
MAINTAINING YOUR VEHICLE 609
WARNING! (Continued)
• Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could
be damaged, causing partial or complete brake
failure. This could result in a collision.
Front/Rear Axle Fluid
For normal service, periodic fluid level checks are not
required. When the vehicle is serviced for other reasons
the exterior surfaces of the axle assembly should be
inspected. If gear oil leakage is suspected inspect the
fluid level. Refer to “Fluids, Lubricants, and Genuine
Parts” in “Maintaining Your Vehicle” for further information.
Front Axle Fluid Level Check
The front axle oil level needs to be between 1/8 in (3 mm)
below the bottom of the fill hole and the bottom of the fill
hole.
The front axle fill and drain plugs should be tightened to
22 to 29 ft lbs (30 to 40 N·m).
CAUTION!
Do not over tighten the plugs as it could damage
them and cause them to leak.
Rear Axle Fluid Level Check
The rear axle oil level needs to be between 1/8 in (3 mm)
below the bottom of the fill hole and the bottom of the fill
hole.
The rear axle fill and drain plugs should be tightened to
22 to 29 ft lbs (30 to 40 N·m) on axles with aluminum
housings. The rear axle fill and drain plugs should be
tightened to 22 to 52 ft lbs (30 to 70 N·m) on axles with
cast iron housings.
7
610 MAINTAINING YOUR VEHICLE
CAUTION!
Do not over tighten the plugs as it could damage then
and cause them to leak.
Adding Fluid
Add fluid at the filler hole, until it runs out of the hole,
when the vehicle is in a level position.
Drain
First remove fill plug, then remove drain plug. RecomSelection Of Lubricant
mended tightening torque for drain and fill plugs is 15 to
Use only the manufacturer’s recommended fluid. Refer
25 ft lbs (20 to 34 N·m).
to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
CAUTION!
Transfer Case
Fluid Level Check
Inspect the transfer case for fluid leaks. If a fluid leak is
found, the transfer case fluid level can be checked by
removing the filler plug located on the back side of the
transfer case. The fluid level should be at the bottom edge
of the filler plug hole when the vehicle is in a level
position.
When installing plugs, do not overtighten. You could
damage them and cause them to leak.
Selection Of Lubricant
Use only the manufacturer’s recommended fluid. Refer
to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
MAINTAINING YOUR VEHICLE 611
Automatic Transmission
Selection Of Lubricant
It is important that the proper lubricant is used in the
transmission to assure optimum transmission performance. Use only the manufacturer’s recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine
Parts” in “Maintaining Your Vehicle” for further information. It is important that the transmission fluid be maintained at the prescribed level using the recommended
fluid.
CAUTION!
Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration
in transmission shift quality and/or torque converter
shudder. Using a transmission fluid other than the
manufacturer’s recommended fluid will require
more frequent fluid and filter changes. Refer to
“Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
Special Additives
Automatic Transmission Fluid (ATF) is an engineered
product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid additives to the transmission. The only exception to this
policy is the use of special dyes to aid in detecting fluid
leaks. In addition, avoid using transmission sealers as
they may adversely affect seals.
7
612 MAINTAINING YOUR VEHICLE
CAUTION!
CAUTION!
Do not use chemical flushes in your transmission as
the chemicals can damage your transmission components. Such damage is not covered by the New
Vehicle Limited Warranty.
• Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque
converter shudder. Using a transmission fluid
other than that recommended by the manufacturer
will require more frequent fluid and filter
changes. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
• The fluid level is preset at the factory and it does
not require adjustment under normal operating
conditions. If a transmission fluid leak occurs,
visit your authorized dealer immediately. Severe
damage to the transmission may occur. Your authorized dealer has the proper tools to adjust the
fluid level accurately.
Fluid Level Check – 3.6L Engine
Regular fluid level checks are not required. For this
reason, the dipstick is omitted.
If you notice fluid loss or transmission slippage or
malfunction, have your authorized dealer check the
transmission fluid level.
MAINTAINING YOUR VEHICLE 613
6. Remove the dipstick again, and note the fluid level on
both sides. The fluid level should be between the “HOT”
(upper) reference holes on the dipstick at normal operating temperature. The fluid level is only valid if there is a
solid coating of oil on both sides of the dipstick. If the
fluid is low, add as required into the dipstick tube. Do
To check the fluid level properly, the following procedure
not overfill. After adding any quantity of oil through the
must be used:
oil fill tube, wait a minimum of two minutes for the oil to
1. Operate the engine at idle speed and normal operating fully drain into the transmission before rechecking the
fluid level.
temperature.
Fluid Level Check – 5.7L Engine
Check the fluid level while the transmission is at normal
operating temperature. This occurs after at least 15 miles
(25 km) of driving. At normal operating temperature the
fluid cannot be held comfortably between the fingertips.
2. The vehicle must be on level ground.
NOTE: If it is necessary to check the transmission below
the operating temperature, the fluid level should be
3. Fully apply the parking brake, and press the brake
between the two “COLD” (lower) holes on the dipstick
pedal.
with the fluid at approximately 70°F (21°C) (room tem4. Place the shift lever momentarily in each gear position perature). If the fluid level is correctly established at
room temperature, it should be between the “HOT”
ending with the shift lever in PARK.
(upper) reference holes when the transmission reaches
5. Remove the dipstick, wipe it clean and reinsert it until
180°F (82°C). Remember it is best to check the level at the
seated.
normal operating temperature.
7
614 MAINTAINING YOUR VEHICLE
CAUTION!
Be aware that if the fluid temperature is below 50°F
(10°C) it may not register on the dipstick. Do not add
fluid until the temperature is elevated enough to
produce an accurate reading.
passable in snow and ice, and those that are sprayed on
trees and road surfaces during other seasons, are highly
corrosive to the metal in your vehicle.
The following maintenance recommendations will enable
you to obtain maximum benefit from the corrosion
resistance built into your vehicle.
What Causes Corrosion?
Corrosion is the result of deterioration or removal of
To prevent dirt and water from entering the transmission
paint and protective coatings from your vehicle.
after checking or replenishing fluid, make certain that the
dipstick cap is properly reseated. It is normal for the The most common causes are:
dipstick cap to spring back slightly from its fully seated
• Road salt, dirt and moisture accumulation.
position, as long as its seal remains engaged in the
• Stone and gravel impact.
dipstick tube.
7. Check for leaks. Release parking brake.
Appearance Care And Protection From Corrosion
• Insects, tree sap and tar.
• Salt in the air near seacoast localities.
Protection Of Body And Paint From Corrosion
Vehicle body care requirements vary according to geo• Atmospheric fallout/industrial pollutants.
graphic locations and usage. Chemicals that make roads
MAINTAINING YOUR VEHICLE 615
Washing
• Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or a mild
car wash soap, and rinse the panels completely with
clear water.
• If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug
and Tar Remover or equivalent to remove.
CAUTION!
• Do not use abrasive or strong cleaning materials
such as steel wool or scouring powder, which will
scratch metal and painted surfaces.
• Use of power washers exceeding 1,200 psi
(8 274 kPa) can result in damage or removal of
paint and decals.
• Use a high quality cleaner wax, such as MOPAR威 Special Care
Cleaner Wax to remove road film, stains, and to • If you drive on salted or dusty roads or if you drive
protect your paint finish. Take care never to scratch the
near the ocean, hose off the undercarriage at least once
paint.
a month.
• Avoid using abrasive compounds and power buffing • It is important that the drain holes in the lower edges
that may diminish the gloss or thin out the paint
of the doors, rocker panels and tailgate must be kept
finish.
clear and open.
7
616 MAINTAINING YOUR VEHICLE
• If you detect any stone chips or scratches in the paint, Wheel And Wheel Trim Care
touch them up immediately. The cost of such repairs is
• All wheels and wheel trim, especially aluminum and
considered the responsibility of the owner.
chrome plated wheels, should be cleaned regularly
• If your vehicle is damaged due to a collision or similar
with a mild soap and water to prevent corrosion.
cause which destroys the paint and protective coating,
• To remove heavy soil and/or excessive brake dust, use
have your vehicle repaired as soon as possible. The
MOPAR威 Wheel Cleaner or equivalent or select a
cost of such repairs is considered the responsibility of
non-abrasive, non-acidic cleaner.
the owner.
• If you carry special cargo such as chemicals, fertilizers,
de-icer salt, etc., assure that such materials are well
packaged and sealed.
• If a lot of driving is done on gravel roads, consider
mud or stone shields behind each wheel.
• Use MOPAR威 Touch Up Paint or equivalent on
scratches or chips as soon as possible. Your authorized
dealer has touch up paint to match the color of your
vehicle.
CAUTION!
Do not use scouring pads, steel wool, a bristle brush,
or metal polishes. Do not use oven cleaner. These
products may damage the wheel’s protective finish.
Avoid automatic car washes that use acidic solutions
or harsh brushes that may damage the wheel’s protective finish. Only MOPAR威 Wheel Cleaner or
equivalent is recommended.
MAINTAINING YOUR VEHICLE 617
Stain Repel Fabric Cleaning Procedure – If
Interior Care
Use MOPAR威 Total Clean or equivalent to clean fabric
Equipped
Stain Repel seats may be cleaned in the following man- upholstery and carpeting.
ner:
Interior Trim should be cleaned starting with a damp
• Remove as much of the stain as possible by blotting cloth, a damp cloth with MOPAR威 Total Clean or equivawith a clean, dry towel.
lent, then MOPAR威 Spot & Stain Remover or equivalent,
if absolutely necessary. Do not use harsh cleaners or
• Blot any remaining stain with a clean, damp towel.
Armor All威. Use MOPAR威 Total Clean or equivalent to
• For tough stains, apply MOPAR威 Total Clean or a mild clean vinyl upholstery.
soap solution to a clean, damp cloth and remove the
Leather Seat Care And Cleaning
stain. Use a fresh, damp towel to remove soap residue.
MOPAR威 Total Clean or equivalent is specifically recom• For grease stains, apply MOPAR威 Multi-Purpose mended for leather upholstery.
Cleaner or equivalent to a clean, damp cloth and
Your leather upholstery can be best preserved by regular
remove the stain. Use a fresh, damp towel to remove
cleaning with a damp soft cloth. Small particles of dirt
soap residue.
can act as an abrasive and damage the leather upholstery
• Do not use any harsh solvents or any other form of and should be removed promptly with a damp cloth.
protectants on Stain Repel products.
Stubborn soils can be removed easily with a soft cloth
and MOPAR威 Total Clean or equivalent. Care should be
7
618 MAINTAINING YOUR VEHICLE
taken to avoid soaking your leather upholstery with any
liquid. Please do not use polishes, oils, cleaning fluids,
solvents, detergents, or ammonia-based cleaners to clean
your leather upholstery. Application of a leather conditioner is not required to maintain the original condition.
WARNING!
To minimize the possibility of scratching the lenses and
reducing light output, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild soap solution followed by rinsing.
Do not use abrasive cleaning components, solvents, steel
wool or other aggressive material to clean the lenses.
Glass Surfaces
All glass surfaces should be cleaned on a regular basis
with MOPAR威 Glass Cleaner or any commercial
household-type glass cleaner. Never use an abrasive type
cleaner. Use caution when cleaning inside rear windows
Cleaning Headlights
equipped with electric defrosters. Do not use scrapers or
Your vehicle has plastic headlights that are lighter and
other sharp instruments which may scratch the elements.
less susceptible to stone breakage than glass headlights.
When cleaning the rearview mirror, spray cleaner on the
Plastic is not as scratch-resistant as glass and therefore
towel or rag that you are using. Do not spray cleaner
different lens cleaning procedures must be followed.
directly on the mirror.
Do not use volatile solvents for cleaning purposes.
Many are potentially flammable, and if used in
closed areas, they may cause respiratory harm.
MAINTAINING YOUR VEHICLE 619
Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this vehicle are
molded in clear plastic. When cleaning the lenses, care
must be taken to avoid scratching the plastic.
If the belts need cleaning, use MOPAR威 Total Clean, a
mild soap solution, or lukewarm water. Do not remove
the belts from the vehicle to wash them. Dry with a soft
cloth.
1. Clean with a wet soft rag. A mild soap solution may be Replace the belts if they appear frayed or worn or if the
used, but do not use high alcohol content or abrasive buckles do not work properly.
cleaners. If soap is used, wipe clean with a clean damp
rag.
2. Dry with a soft cloth.
Seat Belt Maintenance
Do not bleach, dye or clean the belts with chemical
solvents or abrasive cleaners. This will weaken the fabric.
Sun damage will also weaken the fabric.
7
620 MAINTAINING YOUR VEHICLE
FUSES
Totally Integrated Power Module
The Totally Integrated Power Module is located in the
engine compartment. This center contains cartridge fuses
and mini fuses. A description of each fuse and component may be stamped on the inside cover, otherwise the
cavity number of each fuse is stamped on the inside cover
that corresponds to the following chart.
Totally Integrated Power Module
Cavity Cartridge
Fuse
J01
40 Amp
Green
J02
30 Amp
Pink
Mini
Fuse
Description
Air Suspension
Power Liftgate
Module
MAINTAINING YOUR VEHICLE 621
Cavity Cartridge
Fuse
J03
30 Amp
Pink
J04
25 Amp
Natural
J05
25 Amp
Natural
J06
40 Amp
Green
J07
J08
J09
30 Amp
Pink
40 Amp
Green
30 Amp
Pink
Mini
Fuse
Description
Trailer Tow
Driver Door Node
Passenger Door Node
Antilock Brakes
Pump/Stability
Control System
Antilock Brakes
Valve/Stability
Control System
Power Seat
E-Brake
Cavity Cartridge
Fuse
J10
30 Amp
Pink
J11
30 Amp
Pink
J12
30 Amp
Pink
J13
60 Amp
Yellow
J14
20 Amp
Blue
J15
40 Amp
Green
J17
40 Amp
Green
Mini
Fuse
Description
Headlamp Wash
Relay Contact
Drive Train Control
Module
Rear Defroster
Main Ignition Off
Draw (IOD)
Trailer Tow Lamps/
Park Lamps
Front Cabin Fan/
Blower
Starter Motor
Solenoid
7
622 MAINTAINING YOUR VEHICLE
Cavity Cartridge
Fuse
J18
20 Amp
Blue
J19
J20
J21
J22
M1
Mini
Fuse
Description
Powertrain Control
Module/Powertrain
Control Module
Transmission Range
Radiator Fan Motor
HI/Radiator Fan
Motor Low
Front Wiper
60 Amp
Yellow
30 Amp
Pink
20 Amp
Blue
25 Amp
Natural
15 Amp
Blue
Cavity Cartridge
Fuse
M2
M3
M5
M6
Front/Rear Washer
Control
Sunroof Module
M7
Stop Lamp
M9
M8
M10
Mini
Fuse
20 Amp
Yellow
20 Amp
Yellow
25 Amp
Natural
20 Amp
Yellow
20 Amp
Yellow
20 Amp
Yellow
20 Amp
Yellow
15 Amp
Blue
Description
Electronic Limit Slip
Differential/Air
Suspension
Liftgate Unlock/DRL
Relay
115V AC Power
Inverter
Rain Sensor/Cigar
Lighter
Power Outlet #2
(Switchable)
Front Heated Seat &
Steering Wheel
Rear Heated Seats
Video/Universal
Garage Door Opener
MAINTAINING YOUR VEHICLE 623
Cavity Cartridge
Fuse
M11
M12
M13
M14
M15
Mini
Fuse
10 Amp
Red
30 Amp
Green
20 Amp
Yellow
20 Amp
Yellow
20 Amp
Yellow
Description
Heating, Ventilation &
Air Conditioning (Climate Control System)
Radio/Amplifier
Cavity Cartridge
Fuse
M16
M18
M19
Instrument Cluster
M20
Back Up Camera
M21
Power Seat
Module(s)/Adaptive
Cruise Control/Audio
Telematics/Daytime
Running Lights
Relay/Air Suspension
Module/Instrument
Cluster
M22
M23
M24
Mini
Fuse
10 Amp
Red
15 Amp
Blue
25 Amp
Natural
15 Amp
Blue
20 Amp
Yellow
10 Amp
Red
10 Amp
Red
25 Amp
Natural
Description
Occupant Restraint
Controller
Stop Lamp
Automatic
Shutdown 1 and 2
Instrument Cluster
Automatic
Shutdown 3
Horns (Low/High) –
Right
Horns (Low/High) –
Left
Rear Wiper
7
624 MAINTAINING YOUR VEHICLE
Cavity Cartridge
Fuse
M25
M26
M27
Mini
Fuse
20 Amp
Yellow
10 Amp
Red
10 Amp
Red
M28
15 Amp
Blue
M29
10 Amp
Red
15 Amp
Blue
M30
Description
Fuel Pump Motor
Output/Diesel Lift
Pump (Export Only)
Driver Door Switch
Bank
Ignition Switch/
Wireless Control
Module/Keyless
Entry Module
Powertrain
Controller/
Transmission
Controller
Tire Pressure Monitor
J1962 Diag Connector
Cavity Cartridge
Fuse
M31
M32
M33
Mini
Fuse
20 Amp
Yellow
10 Amp
Red
10 Amp
Red
M34
10 Amp
Red
M35
15 Amp
Blue
20 Amp
Yellow
M36
Description
Backup Lamps
Occupant Restraint
Controller
Powertrain
Controller/
Transmission
Controller
Park Assist Module/
Climate Control
System Module/IR
Sensor/Compass
Module
LH Rear Parklamps
Power Outlet
MAINTAINING YOUR VEHICLE 625
Cavity Cartridge
Fuse
M37
M38
Mini
Fuse
10 Amp
Red
25 Amp
Natural
Description
Antilock Brakes/
Stability Control
System Module/
Stoplamp Switch
Sensor
All Door
Lock &Unlock
CAUTION!
• When installing the totally integrated power module cover, it is important to ensure the cover is
properly positioned and fully latched. Failure to
do so may allow water to get into the totally
integrated power module and possibly result in a
electrical system failure.
(Continued)
CAUTION! (Continued)
• When replacing a blown fuse, it is important to
use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated
may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be
corrected.
VEHICLE STORAGE
If you are leaving your vehicle dormant for more than
21 days you may want to take steps to protect your
battery. You may:
• Remove fuse #J13 in the Totally Integrated Power
Module (TIPM) labeled Main Ignition Off Draw (IOD).
• Or, disconnect the negative cable from the battery.
7
626 MAINTAINING YOUR VEHICLE
• Anytime you store your vehicle, or keep it out of
service (i.e. vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
in the fresh air and high blower setting. This will
ensure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
Exterior Lights
Bulb Type
Headlamp – High Intensity
Discharge (HID) . . . . . Service at Authorized Dealer (**)
Headlamp (Low Beam) . . . . . . . . . . . . . . . . . . . . H11
Headlamp (High Beam) . . . . . . . . . . . . . . . . . . . 9005
Front Park/Turn Lamp . . . . . . . . . . . . . . . . . 7444NA
Front Fog Lamps . . . . . . . . . . . . . . . . . . . . . PSX24W
Front Side Marker Lamps . . . . . . . . . . . . W5W or 194
REPLACEMENT BULBS
Rear Turn/Stop/Tail Lamps . . . . . . . . . . . . . . . . 3057
Liftgate Tail Lamps . . . . . . . . . . . . . . . . . . . . . . . 194
Interior Lights
Bulb Type Backup Lamps . . . . . . . . . . . . . . . . . . . . 921 (W16W)
Glove Box Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 194 Rear License Lamps . . . . . . . . . . . . . . . . . . . . . W5W
Grab Handle Lamp . . . . . . . . . . . . . . . . L002825W5W Center High-Mounted Stop Lamp (CHMSL) . . . LED (*)
Overhead Console Reading Lamps . . . . . . . . . VT4976
Rear Cargo Lamp . . . . . . . . . . . . . . . . . . . . . . . 214–2 * CHMSL is not serviceable. It is a LED lamp. To replace
Visor Vanity Lamp . . . . . . . . . . . . . . . . . . . . . V26377 the LED, the entire CHMSL assembly must be replaced.
Underpanel Courtesy Lamps . . . . . . . . . . . . . . . . 906 ** The headlamps are a type of high-voltage discharge
Instrument Cluster (General Illumination) . . . . . . . 103 tube. High voltage can maintain in the circuit even with
Telltale/Hazard Lamp . . . . . . . . . . . . . . . . . . . . . . 74 the headlamp switch off and the key fob removed.
MAINTAINING YOUR VEHICLE 627
Because of this, you should not attempt to service a
headlamp bulb yourself. If a headlamp bulb fails, take
your vehicle to an authorized dealer for service.
NOTE: Numbers refer to commercial bulb types that
can be purchased from your authorized dealer.
If a bulb needs to be replaced, visit your authorized
dealer or refer to the applicable Service Manual.
WARNING!
A transient high voltage occurs at the bulb sockets of
High Intensity Discharge (HID) headlamps when the
headlamp switch is turned ON. It may cause serious
electrical shock or electrocution if not serviced properly. See your authorized dealer for service.
NOTE: On vehicles equipped with High Intensity Discharge (HID) headlamps, when the headlamps are
turned on, there is a blue hue to the lamps. This diminHigh Intensity Discharge Headlamps (HID) –
ishes and becomes more white after approximately
If Equipped
The headlamps are a type of high voltage discharge tube. 10 seconds, as the system charges.
High voltage can remain in the circuit even with the Halogen Headlamps – If Equipped
headlamp switch off and the key removed. Because of
this, you should not attempt to service a headlamp bulb 1. Open the hood.
yourself. If a headlamp bulb fails, take your vehicle to 2. Turn the low or high beam bulb one–quarter turn
an authorized dealer for service.
counterclockwise to remove from housing.
BULB REPLACEMENT
7
628 MAINTAINING YOUR VEHICLE
3. Disconnect the electrical connector and replace the
bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
Front Turn Signal
1. Open the hood.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
Front Fog Lamps
1. Reach through the cutout in the splash shield and
disconnect the wiring harness from the fog lamp connector.
2. Firmly grasp the bulb by the two latches and squeeze
2. Turn the turn signal bulb one–quarter turn counterthem together to unlock the bulb from the back of the
clockwise to remove from housing.
front fog lamp housing.
3. Disconnect the electrical connector and replace the
3. Pull the bulb straight out from the keyed opening in
bulb.
the housing.
MAINTAINING YOUR VEHICLE 629
CAUTION!
• Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If
the bulb comes in contact with any oily surface,
clean the bulb with rubbing alcohol.
• Always use the correct bulb size and type for
replacement. An incorrect bulb size or type may
overheat and cause damage to the lamp, the socket
or the lamp wiring.
4. Align the index tabs of the front fog lamp bulb with
the slots in the collar of the bulb opening on the back of
the front fog lamp housing.
5. Insert the bulb into the housing until the index tabs are
engaged in the slots of the collar.
6. Firmly and evenly push the bulb straight into the lamp
housing until both tabs snap firmly into place and are
fully engaged.
7. Connect the wiring harness to the front fog lamp
connector.
7
630 MAINTAINING YOUR VEHICLE
Rear Tail, Stop, Turn Signal, And Backup Lamps
1. Raise the liftgate.
2. Remove the two push-pins from the tail lamp housing.
4. Twist socket counter clockwise and remove from
lamp.
5. Pull the bulb to remove it from the socket.
6. Replace the bulb, reinstall the socket, and reattach the
3. Grasp the tail lamp and pull firmly rearward to
lamp assembly.
disengage the lamp from the aperture panel.
Rear Liftgate Mounted Tail Lamp
1. Raise the liftgate.
2. Use a fiber stick or flat blade screw driver to pry the
lower trim from the liftgate.
3. Disconnect the two trim panel lights.
4. Tail lamps are now visible. Rotate socket(s) counter
clockwise.
5. Remove/replace bulb(s).
6. Reinstall the socket(s)
7. Reverse process to reinstall the liftgate trim.
MAINTAINING YOUR VEHICLE 631
Center High-Mounted Stop Lamp (CHMSL)
Rear License Lamp
The center high-mounted stop lamp is an LED assembly.
1. Use a screw driver to gently pry against the side of the
See your authorized dealer for replacement.
snap tab to remove the license lamp lens.
2. Pull bulb from socket.
3. Replace bulb.
4. Reinstall lens.
7
632 MAINTAINING YOUR VEHICLE
FLUID CAPACITIES
Fuel (Approximate)
3.6L and 5.7L Engines
Engine Oil with Filter
3.6L Engine (SAE 5W-30, API Certified)
5.7L Engine (SAE 5W-20, API Certified)
Cooling System *
3.6L Engine (MOPAR威 Engine Coolant/Antifreeze
5-Year/100,000 Mile Formula or equivalent) – Without Trailer
Tow Package
3.6L Engine (MOPAR威 Engine Coolant/Antifreeze
5-Year/100,000 Mile Formula or equivalent) – With Trailer
Tow Package
3.6L Engine (MOPAR威 Engine Coolant/Antifreeze
5-Year/100,000 Mile Formula or equivalent) – Front and Rear
Heat Without Trailer Tow Package
U.S.
Metric
24 Gallons
91 Liters
6 Quarts
7 Quarts
5.6 Liters
6.6 Liters
10 Quarts
9.8 Liters
11 Quarts
10.4 Liters
11.5 Quarts
10.8 Liters
MAINTAINING YOUR VEHICLE 633
3.6L Engine (MOPAR威 Engine Coolant/Antifreeze
5-Year/100,000 Mile Formula or equivalent) – Front and Rear
Heat With Trailer Tow Package
5.7 Liter Engine (MOPAR威 Engine Coolant/Antifreeze
5-Year/100,000 Mile Formula or equivalent) – Front and Rear
Heat Without Trailer Tow Package
5.7 Liter Engine (MOPAR威 Engine Coolant/Antifreeze
5-Year/100,000 Mile Formula or equivalent) – Front and Rear
Heat With Trailer Tow Package
* Includes heater and coolant recovery bottle filled to MAX level.
U.S.
12 Quarts
Metric
11.4 Liters
16 Quarts
15.2 Liters
17 Quarts
16.2 Liters
7
634 MAINTAINING YOUR VEHICLE
FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine
Component
Engine Coolant
Engine Oil – 3.6L Engine
Engine Oil – 5.7L Engine
Engine Oil Filter
Spark Plugs – 3.6L Engine
Spark Plugs – 5.7L Engine
Fuel Selection – 3.6L Engine
Fuel Selection – 5.7L Engine
Fluid, Lubricant, or Genuine Part
MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT
(Hybrid Organic Additive Technology) or equivalent.
Use API Certified SAE 5W-30 Engine Oil, meeting the requirements of
Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for
correct SAE grade.
Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of
Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for
correct SAE grade.
MOPAR威 Engine Oil Filter or equivalent.
RER8ZWYCB4 (Gap 0.043 in [1.1 mm])
LZFR5C–11G (Gap 0.043 in [1.1 mm])
87 Octane
87 Octane Acceptable – 89 Octane Recommended
MAINTAINING YOUR VEHICLE 635
Chassis
Component
Automatic Transmission
Transfer Case – 3.6L Engine
Transfer Case – 5.7L Engine
Axle Differential (Front-Rear)
Brake Master Cylinder
Power Steering Reservoir –
3.6L Engine
Power Steering Reservoir –
5.7L Engine
Fluid, Lubricant, or Genuine Part
MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed
ATF+4威 product.
Shell Automatic Transmission Fluid 3353 or equivalent.
MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed
ATF+4威 product.
We recommend you use MOPAR威 GL-5 Synthetic Axle Lubricant
SAE 75W-85.
MOPAR威 DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3,
SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
Use only recommended brake fluids or equivalent.
MOPAR威 Hydraulic Fluid or equivalent meeting MS-11655, such as
Fuchs EG ZH 3044 or Pentosin CHF 11s
MOPAR威 Power Steering Fluid +4, MOPAR威 ATF+4威 Automatic
Transmission Fluid or equivalent licensed ATF+4威 product.
7
MAINTENANCE SCHEDULES
CONTENTS
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 638
▫ Required Maintenance Intervals . . . . . . . . . . 640
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
M
A
I
N
T
E
N
A
N
C
E
638 MAINTENANCE SCHEDULES
MAINTENANCE SCHEDULE
The Scheduled Maintenance services listed in this
manual must be done at the times or mileages specified
to protect your vehicle warranty and ensure the best
vehicle performance and reliability. More frequent maintenance may be needed for vehicles in severe operating
conditions, such as dusty areas and very short trip
driving. Inspection and service should also be done
S anytime a malfunction is suspected.
Based on engine operation conditions, the oil change
indicator message will illuminate. This means that service is required for your vehicle. Operating conditions
such as frequent short-trips, trailer tow, extremely hot or
cold ambient temperatures, and E85 fuel usage will
influence when the “Change Oil” message is displayed.
Your vehicle is equipped with an automatic oil change Depending on operating conditions, the message may
indicator system. The oil change indicator system will appear as early as 3,500 miles (5 630 km) since last reset.
remind you that it is time to take your vehicle in for Have your vehicle serviced as soon as possible, within
scheduled maintenance.
the next 500 miles (805 km).
C
H
E
D
U
L
E
S On
8
On Non-EVIC equipped vehicles, “Change Oil” will flash
in the instrument cluster odometer and a single chime
will sound, indicating that an oil change is necessary.
Electronic Vehicle Information Center (EVIC)
equipped vehicles, “Oil Change Required” will be displayed in the EVIC and a single chime will sound,
indicating that an oil change is necessary.
MAINTENANCE SCHEDULES 639 M
NOTE:
• The oil change indicator message will not monitor the
time since the last oil change. Change your vehicle’s
oil if it has been six months since your last oil change,
even if the oil change indicator message is NOT
illuminated.
referring to the steps described under “Electronic Vehicle
Information Center (EVIC)/Oil Change Required” in
“Understanding Your Instrument Panel” or under
“Instrument Cluster Description/Odometer/Trip Odometer” in “Understanding Your Instrument Panel” for
further information.
• Change your engine oil more often if you drive your At Each Stop For Fuel
vehicle off-road for an extended period of time.
• Check the engine oil level about five minutes after a
• Under no circumstances should oil change intervals
fully warmed engine is shut off. Checking the oil level
exceed 8,000 miles (13 000 km) or six months, whichwhile the vehicle is on level ground will improve the
ever comes first.
accuracy of the oil level reading. Add oil only when
the level is at or below the ADD or MIN mark.
Your authorized dealer will reset the oil change indicator
message after completing the scheduled oil change. If a • Check the windshield washer solvent and add if
required.
scheduled oil change is performed by someone other
than your authorized dealer, the message can be reset by
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
M
A
I
N
T
E
N
A
N
C
E
640 MAINTENANCE SCHEDULES
Once A Month
• Check tire pressure and look for unusual wear or • Change the engine oil filter.
damage.
• Inspect the brake hoses and lines.
• Inspect the battery and clean and tighten the terminals
CAUTION!
as required.
• Check the fluid levels of the coolant reservoir, brake
master cylinder, power steering and transmission
S
C
(5.7L only) and add as needed.
H
E • Check all lights and other electrical items for correct
D
operation.
U
L
E
S
8
At Each Oil Change
Failure to perform the required maintenance items
may result in damage to the vehicle.
Required Maintenance Intervals
Refer to the Maintenance Schedules on the following
pages for the required maintenance intervals.
MAINTENANCE SCHEDULES 641 M
8,000 Miles (13,000 km) or
6 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil
filter.
❏ Rotate the tires, rotate at the first sign of
irregular wear, even if it occurs before
8,000 miles (13 000 km).
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
16,000 Miles (26,000 km) or 12 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
16,000 miles (26 000 km).
❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the
engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect exhaust system. Perform the first inspection at 16,000 miles (26 000 km) or
12 months.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
M 642 MAINTENANCE SCHEDULES
A
I 24,000 Miles (39,000 km) or
N
T 18 Months Maintenance
E Service Schedule
N ❏ Change the engine oil and engine oil
A
filter.
N ❏ Rotate the tires, rotate at the first sign of
C
irregular wear, even if it occurs before
E
S
C
H
E
D
U
L
E
S
8
24,000 miles (39 000 km).
❏ Inspect the CV joints.
❏ Inspect exhaust system.
❏ Inspect the front and rear axle fluid,
change if using your vehicle for police,
taxi, fleet, off-road or frequent trailer
towing.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
32,000 Miles (52,000 km) or 24 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
32,000 miles (52 000 km).
❏ Replace the engine air cleaner filter.
❏ Replace the air conditioning filter.
❏ Replace the spark plugs (5.7L Engine).
❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
❏ Inspect the transfer case fluid.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
MAINTENANCE SCHEDULES 643 M
40,000 Miles (65,000 km) or
30 Months Maintenance
Service Schedule
48,000 Miles (78,000 km) or 36 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil
filter.
❏ Rotate the tires, rotate at the first sign of
irregular wear, even if it occurs before
40,000 miles (65 000 km).
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
48,000 miles (78 000 km).
❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the
engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect the CV joints.
❏ Inspect exhaust system.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet,
off-road or frequent trailer towing.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
M 644 MAINTENANCE SCHEDULES
A
I 56,000 Miles (91,000 km) or
N
T 42 Months Maintenance
E Service Schedule
N ❏ Change the engine oil and engine oil
A
filter.
N ❏ Rotate the tires, rotate at the first sign of
C
irregular wear, even if it occurs before
E
56,000 miles (91 000 km).
S
C
H
E
D
U
L
E
S
8
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
64,000 Miles (104,000 km) or 48 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
64,000 miles (104 000 km).
❏ Replace the engine air cleaner filter.
❏ Replace the air conditioning filter.
❏ Inspect the brake linings; replace if necessary.
❏ Replace the spark plugs (5.7L Engine).
❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
❏ Change the automatic transmission fluid and filter(s) if using your vehicle for any of the
following: police, taxi, fleet, or frequent trailer towing.
❏ Change the transfer case fluid if using your vehicle for any of the following: police, taxi,
fleet, or frequent trailer towing.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
MAINTENANCE SCHEDULES 645 M
72,000 Miles (117,000 km) or
54 Months Maintenance
Service Schedule
80,000 Miles (130,000 km) or 60 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil
filter.
❏ Rotate the tires, rotate at the first sign of
irregular wear, even if it occurs before
72,000 miles (117 000 km).
❏ Inspect the CV joints.
❏ Inspect exhaust system.
❏ Inspect the front and rear axle fluid,
change if using your vehicle for police,
taxi, fleet, off-road or frequent trailer
towing.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
80,000 miles (130 000 km).
❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the
engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter.
❏ Flush and replace the engine coolant at 60 months or 104,000 miles (169 000 km) whichever
comes first.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
M 646 MAINTENANCE SCHEDULES
A
I 88,000 Miles (143,000 km) or
N
T 66 Months Maintenance
E Service Schedule
N ❏ Change the engine oil and engine oil
A
filter.
N ❏ Rotate the tires, rotate at the first sign of
C
irregular wear, even if it occurs before
E
88,000 miles (143 000 km).
S
C
H
E
D
U
L
E
S
8
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
MAINTENANCE SCHEDULES 647 M
96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
Change the engine oil and engine oil filter.
Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km).
Replace the engine air cleaner filter.
Replace the air conditioning filter.
Replace the spark plugs (3.6L Engine).
Replace the spark plugs (5.7L Engine).
Inspect and replace PCV valve if necessary.
Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Inspect the transfer case fluid.
Inspect the brake linings, replace if necessary.
Inspect the CV joints.
Inspect exhaust system.
Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;
replace if necessary.
❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
M 648 MAINTENANCE SCHEDULES
A
I 104,000 Miles (169,000 km) or
N
T 78 Months Maintenance
E Service Schedule
N ❏ Change the engine oil and engine oil
A
filter.
N ❏ Rotate the tires, rotate at the first sign of
C
irregular wear, even if it occurs before
E
S
C
H
E
D
U
L
E
S
8
104,000 miles (169 000 km).
❏ Flush and replace the engine coolant at
104,000 miles (169 000 km) or 60 months
whichever comes first.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
112,000 Miles (182,000 km) or 84 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
112,000 miles (182 000 km).
❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the
engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
MAINTENANCE SCHEDULES 649 M
120,000 Miles (195,000 km) or 90 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
120,000 miles (195 000 km).
❏ Inspect the CV joints.
❏ Inspect exhaust system.
❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet,
off-road or frequent trailer towing.
❏ Change the automatic transmission fluid and filter(s).
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
M 650 MAINTENANCE SCHEDULES
A
I 128,000 Miles (208,000 km) or 96 Months Maintenance Service
N
T Schedule
E ❏ Change the engine oil and engine oil filter.
N ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
128,000 miles (208 000 km).
A
N ❏ Replace the engine air cleaner filter.
C ❏ Replace the air conditioning filter.
E ❏ Replace the spark plugs (5.7L Engine).
S
C
H
E
D
U
L
E
S
8
❏
❏
❏
❏
136,000 Miles (221,000 km) or
102 Months Maintenance
Service Schedule
❏ Change the engine oil and engine oil
filter.
❏ Rotate the tires, rotate at the first sign of
irregular wear, even if it occurs before
136,000 miles (221 000 km).
Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Change the transfer case fluid.
Inspect the brake linings, replace if necessary.
Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
MAINTENANCE SCHEDULES 651 M
144,000 Miles (234,000 km) or 108 Months Maintenance Service
Schedule
❏ Change the engine oil and engine oil filter.
❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
144,000 miles (234 000 km).
❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the
engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter.
❏ Inspect the brake linings, replace if necessary.
❏ Inspect the CV joints.
❏ Inspect exhaust system.
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end play; replace if necessary.
❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet,
off-road or frequent trailer towing.
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
152,000 Miles (247,000 km) or
114 Months Maintenance
Service Schedule
❏ Change the engine oil and engine oil
filter.
❏ Rotate the tires, rotate at the first sign of
irregular wear, even if it occurs before
152,000 miles (247 000 km).
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
Odometer Reading
Repair Order #
Signature, Authorized Service Center
Date
Dealer Code
8
M
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
652 MAINTENANCE SCHEDULES
† This maintenance is recommended by the manufacturer
to the owner, but is not required to maintain emissions
warranty.
WARNING!
• You can be badly injured working on or around a
motor vehicle. Do only service work for which you
have the knowledge and the right equipment. If
you have any doubt about your ability to perform
a service job, take your vehicle to a competent
mechanic.
• Failure to properly inspect and maintain your
vehicle could result in a component malfunction
and effect vehicle handling and performance. This
could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE
CONTENTS
䡵 Suggestions For Obtaining Service For Your
Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
▫ Customer Assistance For The Hearing Or
Speech Impaired (TDD/TTY) . . . . . . . . . . . . 657
▫ Prepare For The Appointment . . . . . . . . . . . 655
▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 657
▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 655
䡵 Warranty Information . . . . . . . . . . . . . . . . . . 658
▫ Be Reasonable With Requests . . . . . . . . . . . . 655
䡵 MOPAR威 Parts . . . . . . . . . . . . . . . . . . . . . . . 658
䡵 If You Need Assistance
. . . . . . . . . . . . . . . . . 655
䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . 658
▫ Chrysler Group LLC Customer Center . . . . . 656
▫ In The 50 United States And
Washington, D.C. . . . . . . . . . . . . . . . . . . . . 658
▫ Chrysler Canada Inc. Customer Center . . . . . 656
▫ In Mexico Contact . . . . . . . . . . . . . . . . . . . . 656
▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . 659
䡵 Publication Order Forms . . . . . . . . . . . . . . . . 659
9
654 IF YOU NEED CONSUMER ASSISTANCE
䡵 Department Of Transportation Uniform Tire
Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 661
▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 661
▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 661
▫ Temperature Grades . . . . . . . . . . . . . . . . . . 662
IF YOU NEED CONSUMER ASSISTANCE 655
the service advisor and list the items in order of priority.
At many authorized dealers, you may obtain a rental
vehicle at a minimal daily charge. If you need a rental, it
Prepare For The Appointment
is advisable to make these arrangements when you call
If you’re having warranty work done, be sure to have the
for an appointment.
right papers with you. Take your warranty folder. All
work to be performed may not be covered by the IF YOU NEED ASSISTANCE
warranty. Discuss additional charges with the service The manufacturer and its authorized dealers are vitally
manager. Keep a maintenance log of your vehicle’s interested in your satisfaction. We want you to be happy
service history. This can often provide a clue to the with our products and services.
current problem.
Warranty service must be done by an authorized dealer.
Prepare A List
We strongly recommend that you take the vehicle to an
Make a written list of your vehicle’s problems or the authorized dealer. They know your vehicle the best, and
specific work you want done. If you’ve had an accident are most concerned that you get prompt and high quality
or work done that is not on your maintenance log, let the service. The manufacturer’s authorized dealers have the
service advisor know.
facilities, factory-trained technicians, special tools, and
the latest information to ensure the vehicle is fixed
Be Reasonable With Requests
If you list a number of items and you must have your correctly and in a timely manner.
vehicle by the end of the day, discuss the situation with
SUGGESTIONS FOR OBTAINING SERVICE FOR
YOUR VEHICLE
9
656 IF YOU NEED CONSUMER ASSISTANCE
This is why you should always talk to an authorized Chrysler Group LLC Customer Center
dealer’s service manager first. Most matters can be re- P.O. Box 21–8004
Auburn Hills, MI 48321–8004
solved with this process.
Phone: (800) 423–6343
• If for some reason you are still not satisfied, talk to the
general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center
P.O. Box 1621
ship. They want to know if you need assistance.
Windsor, Ontario N9A 4H6
• If an authorized dealership is unable to resolve the
Phone: (800) 465–2001 English / (800) 387–9983 French
concern, you may contact the manufacturer’s customer
In Mexico contact:
center.
Av. Prolongacion Paseo de la Reforma, 1240
Any communication to the manufacturer’s customer cenSante Fe C.P. 05109
ter should include the following information:
Mexico, D. F.
• Owner’s name and address
In Mexico City: 5081-7568
Outside Mexico City: 1-800-505-1300
• Owner’s telephone number (home and office)
• Authorized dealership name
• Vehicle Identification Number (VIN)
• Vehicle delivery date and mileage
IF YOU NEED CONSUMER ASSISTANCE 657
Customer Assistance For The Hearing Or Speech
Impaired (TDD/TTY)
To assist customers who have hearing difficulties, the
manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer
center. Any hearing or speech impaired customer, who
has access to a TDD or a conventional teletypewriter
(TTY) in the United States, can communicate with the
manufacturer by dialing 1–800–380–CHRY.
Canadian residents with hearing difficulties that require
assistance can use the special needs relay service offered
by Bell Canada. For TTY teletypewriter users, dial 711
and for Voice callers, dial 1 800 855-0511 to connect with
a Bell Relay Service operator.
the manufacturer’s service contracts. If you purchased a
manufacturer’s service contract, you will receive Plan
Provisions and an Owner Identification Card in the mail
within three weeks of the vehicle delivery date. If you
have any questions about the service contract, call the
manufacturer’s Service Contract National Customer
Hotline at 1-800-521-9922 (Canadian residents, call (800)
465–2001 English / (800) 387–9983 French).
The manufacturer will not stand behind any service
contract that is not the manufacturer’s service contract. It
is not responsible for any service contract other than the
manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract,
and you require service after the manufacturer’s New
Service Contract
Vehicle Limited Warranty expires, please refer to the
You may have purchased a service contract for a vehicle contract documents, and contact the person listed in
to help protect you from the high cost of unexpected those documents.
repairs after the manufacturer’s New Vehicle Limited
Warranty expires. The manufacturer stands behind only
9
658 IF YOU NEED CONSUMER ASSISTANCE
We appreciate that you have made a major investment
when you purchased the vehicle. An authorized dealer
has also made a major investment in facilities, tools, and
training to assure that you are absolutely delighted with
the ownership experience. You’ll be pleased with their
sincere efforts to resolve any warranty issues or related
concerns.
WARNING!
Engine exhaust, some of its constituents, and certain
vehicle components contain, or emit, chemicals
known to the State of California to cause cancer and
birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain
products of component wear contain, or emit, chemicals known to the State of California to cause cancer
and birth defects, or other reproductive harm.
WARRANTY INFORMATION
See the Warranty Information Booklet, located on the
DVD, for the terms and provisions of Chrysler Group
LLC warranties applicable to this vehicle and market.
MOPAR姞 PARTS
MOPAR威 fluids, lubricants, parts, and accessories are
available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle
operating at its best.
REPORTING SAFETY DEFECTS
In the 50 United States and Washington, D.C.
If you believe that your vehicle has a defect that could
cause a crash or cause injury or death, you should
immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying the
manufacturer.
IF YOU NEED CONSUMER ASSISTANCE 659
If NHTSA receives similar complaints, it may open an
investigation, and if it finds that a safety defect exists in
a group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in
individual problems between you, your authorized
dealer, and the manufacturer.
In Canada
If you believe that your vehicle has a safety defect,
you should contact the Customer Service Department
immediately. Canadian customers who wish to report
a safety defect to the Canadian government should
contact Transport Canada, Motor Vehicle Defect
Investigations and Recalls at 1-800-333-0510 or go to
To contact NHTSA, you may either call the Auto Safety
http://www.tc.gc.ca/roadsafety/
Hotline toll free at 1–888–327–4236 (TTY: 1–800–424–
9153), or go to http://www.safercar.gov; or write to: PUBLICATION ORDER FORMS
Administrator, NHTSA, 1200 New Jersey Avenue, SE., To order the following manuals, you may use either the
West Building, Washington, D.C. 20590. You can also website or the phone numbers listed below. Visa,
obtain other information about motor vehicle safety from Mastercard, American Express, and Discover orders are
http://www.safercar.gov.
accepted. If you prefer mailing your payment, please call
for an order form.
NOTE: A street address is required when ordering
manuals (no P.O. Boxes).
9
660 IF YOU NEED CONSUMER ASSISTANCE
• Service Manuals
• Owner’s Manuals
These comprehensive Service Manuals provide the
These Owner’s Manuals have been prepared with the
information that students and professional technicians
assistance of service and engineering specialists to
need in diagnosing/troubleshooting, problem solving,
acquaint you with specific Chrysler Group LLC vemaintaining, servicing, and repairing Chrysler Group
hicles. Included are starting, operating, emergency
LLC vehicles. A complete working knowledge of the
and maintenance procedures as well as specifications,
vehicle, system, and/or components is written in
capabilities and safety tips.
straightforward language with illustrations, diagrams,
Call toll free at:
and charts.
• 1–800–890–4038 (U.S.)
• Diagnostic Procedure Manuals
Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians
to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to
find and correct problems the first time, using step-bystep troubleshooting and drivability procedures,
proven diagnostic tests and a complete list of all tools
and equipment.
• 1–800–387–1143 (Canada)
Or
Visit us on the Worldwide Web at:
• www.techauthority.com
IF YOU NEED CONSUMER ASSISTANCE 661
DEPARTMENT OF TRANSPORTATION UNIFORM
TIRE QUALITY GRADES
The following tire grading categories were established by
the National Highway Traffic Safety Administration. The
specific grade rating assigned by the tire’s manufacturer
in each category is shown on the sidewall of the tires on
your vehicle.
significantly from the norm due to variations in driving
habits, service practices, and differences in road characteristics and climate.
Traction Grades
The Traction grades, from highest to lowest, are AA, A, B,
and C. These grades represent the tire’s ability to stop on
wet pavement, as measured under controlled conditions
All passenger car tires must conform to Federal safety on specified government test surfaces of asphalt and
concrete. A tire marked C may have poor traction perforrequirements in addition to these grades.
mance.
Treadwear
The Treadwear grade is a comparative rating, based on
WARNING!
the wear rate of the tire when tested under controlled
conditions on a specified government test course. For The traction grade assigned to this tire is based on
example, a tire graded 150 would wear one and one-half straight-ahead braking traction tests, and does not
times as well on the government course as a tire graded include acceleration, cornering, hydroplaning, or
100. The relative performance of tires depends upon the peak traction characteristics.
actual conditions of their use, however, and may depart
9
662 IF YOU NEED CONSUMER ASSISTANCE
Temperature Grades
The temperature grades are A (the highest), B, and C,
representing the tire’s resistance to the generation of heat
and its ability to dissipate heat, when tested under
controlled conditions on a specified indoor laboratory
test wheel. Sustained high temperature can cause the
material of the tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance, which all
passenger car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test
wheel, than the minimum required by law.
WARNING!
The temperature grade for this tire is established for
a tire that is properly inflated and not overloaded.
Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause
heat buildup and possible tire failure.
INDEX
10
664 INDEX
Adaptive Cruise Control (ACC) (Cruise Control) . . 208
Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 514
Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 590
Air Conditioner Maintenance . . . . . . . . . . . . . . . 593
Air Conditioning Filter . . . . . . . . . . . . . . . . . . . . 594
Air Conditioning Refrigerant . . . . . . . . . . . . . . . 594
Air Conditioning System . . . . . . . . . . . . . . . . . . 408
Air Conditioning, Operating Tips . . . . . . . . . . . . 416
Air Conditioning, Rear Zone . . . . . . . . . . . . . . . . 414
Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 590
Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . . . . 489
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67,76
Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . 77
Airbag Light . . . . . . . . . . . . . . . . . . . 74,75,80,99,305
Airbag Maintenance . . . . . . . . . . . . . . . . . . . . . . . 79
Airbag, Side . . . . . . . . . . . . . . . . . . . . . . 70,73,75,76
Airbag, Window (Side Curtain) . . . . . . . . . . . 71,73,76
Alarm (Security Alarm) . . . . . . . . . . . . . . . . . 20,305
Alarm, Panic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
All Wheel Drive (AWD) . . . . . . . . . . . . . . . . . . . 450
Alterations/Modifications, Vehicle . . . . . . . . . . . . . 9
Antenna, Satellite Radio . . . . . . . . . . . . . . . . . . . 361
Anti-Lock Brake System (ABS) . . . . . . . . . . . . . . 468
Anti-Lock Warning Light . . . . . . . . . . . . . . . . . . 302
Anti-Theft System . . . . . . . . . . . . . . . . . . . . . . . 305
Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . . 632
Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . 614
Assist, Hill Start . . . . . . . . . . . . . . . . . . . . . . . . 474
Assistance Towing . . . . . . . . . . . . . . . . . . . . . . . 137
Auto Down Power Windows . . . . . . . . . . . . . . . . 43
Automatic Dimming Mirror . . . . . . . . . . . . . . . . 110
Automatic Door Locks . . . . . . . . . . . . . . . . . . . . . 36
Automatic Headlights . . . . . . . . . . . . . . . . . . . . 189
Automatic Temperature Control (ATC) . . . . . . . . . 408
Automatic Transmission . . . . . . . . . . . . . 432,440,611
Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . 613
Fluid and Filter Changes . . . . . . . . . . . . . . . 611
INDEX 665
Master Cylinder . . . . . . . . . . . . . . . . . . . . . 607
Fluid Level Check . . . . . . . . . . . . . . . . . 612,613
Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . 611
Warning Light . . . . . . . . . . . . . . . . . . . . . . . 305
Special Additives . . . . . . . . . . . . . . . . . . . . . 611
Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . 439,447 Brake/Transmission Interlock . . . . . . . . . . . . . . . 432
Auxiliary Electrical Outlet (Power Outlet) . . . . . . 263 Break-In Recommendations, New Vehicle . . . . . . . . 97
Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . 263 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 626,627
Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 484
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 591 Calibration, Compass . . . . . . . . . . . . . . . . . . . . . 329
Keyless Transmitter Replacement (RKE) . . . . . 27 Camera, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52,99 Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . . 632
Blind Spot Monitoring . . . . . . . . . . . . . . . . . . . . 115 Caps, Filler
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
Body Mechanism Lubrication . . . . . . . . . . . . . . . 595
Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 469
Power Steering . . . . . . . . . . . . . . . . . . . . . . 464
Radiator (Coolant Pressure) . . . . . . . . . . . . . 604
Brake Control System, Electronic . . . . . . . . . . . . . 467
Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615
Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 607 Carbon Monoxide Warning . . . . . . . . . . . . . . . 98,515
Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . 468 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 523
Fluid Check . . . . . . . . . . . . . . . . . . . . . . . . 607 Cargo Area Cover . . . . . . . . . . . . . . . . . . . . . . . 280
10
666 INDEX
Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . 279
Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . 279
Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Luggage Carrier . . . . . . . . . . . . . . . . . . . . . 284
Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 281
Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . 123,408
Center High Mounted Stop Light . . . . . . . . . . . . 631
Certification Label . . . . . . . . . . . . . . . . . . . . . . . 523
Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 552
Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . 480
Check Engine Light
(Malfunction Indicator Light) . . . . . . . . . . . . . . . 584
Checking Your Vehicle For Safety . . . . . . . . . . . . . 98
Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Child Restraint . . . . . . . . . . . . . . . . . . . . 81,84,87,91
Child Restraint Tether Anchors . . . . . . . . . . . . . 85,87
Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . . 36
Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . . 512
Cleaning
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616
Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 408
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341,350
Cold Weather Operation . . . . . . . . . . . . . . . . . . . 428
Compact Disc (CD) Maintenance . . . . . . . . . . . . . 407
Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 492
Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
Compass Calibration . . . . . . . . . . . . . . . . . . . . . 329
Compass Variance . . . . . . . . . . . . . . . . . . . . . . . 328
Computer, Trip/Travel . . . . . . . . . . . . . . . . . . . . 325
Connector
UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
Universal Consumer Interface (UCI) . . . . . . . 364
Conserving Fuel . . . . . . . . . . . . . . . . . . . . . . . . 323
Console, Overhead . . . . . . . . . . . . . . . . . . . . . . . 248
Contract, Service . . . . . . . . . . . . . . . . . . . . . . . . 657
INDEX 667
Defroster, Windshield . . . . . . . . . . . . . . . . . . 100,413
Diagnostic System, Onboard . . . . . . . . . . . . . . . . 583
Dipsticks
Automatic Transmission . . . . . . . . . . . . . . . . 613
Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . 587
Power Steering . . . . . . . . . . . . . . . . . . . . . . 464
Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 574
Disposal
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 590
Used Engine Fluids . . . . . . . . . . . . . . . . . . . 590
Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 36
Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 250
Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
Off-Pavement . . . . . . . . . . . . . . . . . . . . . . . 457
Off-Road . . . . . . . . . . . . . . . . . . . . . . . . . . 457
Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 80
Daytime Running Lights . . . . . . . . . . . . . . . . . . . 191 Driving to Achieve Maximum Fuel Economy . . . . 323
Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 586
Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 283 E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
Cooling System . . . . . . . . . . . . . . .
Adding Coolant (Antifreeze) . . .
Coolant Capacity . . . . . . . . . . .
Coolant Level . . . . . . . . . . . . .
Disposal of Used Coolant . . . . .
Drain, Flush, and Refill . . . . . .
Inspection . . . . . . . . . . . . . . . .
Points to Remember . . . . . . . .
Pressure Cap . . . . . . . . . . . . . .
Radiator Cap . . . . . . . . . . . . .
Selection of Coolant (Antifreeze)
Cruise Control (Speed Control) . . . .
Cupholders . . . . . . . . . . . . . . . . . .
Customer Assistance . . . . . . . . . . .
. . . . . . . . . . 601
. . . . . . . . . . 603
. . . . . . . . . . 632
. . . . . . . . . . 605
. . . . . . . . . . 605
. . . . . . . . . . 602
. . . . . . . . . . 601
. . . . . . . . . . 606
. . . . . . . . . . 604
. . . . . . . . . . 604
. . . . . . . 602,632
. . . . . . . . . . 208
. . . . . . . . . . 270
. . . . . . . . . . 655
10
668 INDEX
Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . 112 Emission Control System Maintenance . . . . . . . . . 584
Electrical Outlet, Auxiliary (Power Outlet) . . . . . . 263 Engine
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . 590
Electronic Brake Control System . . . . . . . . . . . . . 467
Block Heater . . . . . . . . . . . . . . . . . . . . . . . . 429
Anti-Lock Brake System . . . . . . . . . . . . . . . . 468
Break-In Recommendations . . . . . . . . . . . . . . 97
Brake Assist System . . . . . . . . . . . . . . . . . . . 469
Compartment . . . . . . . . . . . . . . . . . . . . 581,582
Electronic Roll Mitigation . . . . . . . . . . . . . . . 470
Compartment Identification . . . . . . . . . . 581,582
Traction Control System . . . . . . . . . . . . . . . . 468
Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . 601
Electronic Roll Mitigation (ERM) . . . . . . . . . . . . . 470
Exhaust Gas Caution . . . . . . . . . . . . . . 48,98,515
Electronic Speed Control (Cruise Control) . . . . 205,208
Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . 428
Electronic Stability Control (ESC) . . . . . . . . . . . . . 470
Flooded, Starting . . . . . . . . . . . . . . . . . . . . . 428
Electronic Vehicle Information
Fuel Requirements . . . . . . . . . . . . . . . . . 511,632
Center (EVIC) . . . . . . . . . . . . . . . . . . . . . . . 303,309
Jump Starting . . . . . . . . . . . . . . . . . . . . . . . 567
Electronically Shifted Transfer Case . . . . . . . . . . . 450
Emergency, In Case of
Multi-Displacement . . . . . . . . . . . . . . . . . . . 465
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587,632
Freeing Vehicle When Stuck . . . . . . . . . . . . . 571
Oil Change Interval . . . . . . . . . . . . . . . . . . . 588
Hazard Warning Flasher . . . . . . . . . . . . . . . 551
Oil Disposal . . . . . . . . . . . . . . . . . . . . . . . . 590
Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552
Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 590
Jump Starting . . . . . . . . . . . . . . . . . . . . . . . 567
Oil Filter Disposal . . . . . . . . . . . . . . . . . . . . 590
Tow Hooks . . . . . . . . . . . . . . . . . . . . . . . . . 573
INDEX 669
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 590
Engine Oil Disposal . . . . . . . . . . . . . . . . . . . 590
Finish Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615
Flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
Hazard Warning . . . . . . . . . . . . . . . . . . . . . 551
Turn Signal . . . . . . . . . . . . . . . . 101,303,628,630
Flexible Fuel Vehicles
Cruising Range . . . . . . . . . . . . . . . . . . . . . . 518
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 518
Fuel Requirements . . . . . . . . . . . . . . . . . 515,517
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 519
Replacement Parts . . . . . . . . . . . . . . . . . . . . 519
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 428
Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 632
Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Fluid Level Checks
Filters
Automatic Transmission . . . . . . . . . . 611,612,613
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . 590
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607
Air Conditioning . . . . . . . . . . . . . . . . . . . . . 594
Oil Selection . . . . . . . . . . . . . . . . . . . . . 588,632
Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . 589
Overheating . . . . . . . . . . . . . . . . . . . . . . . . 551
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
Temperature Gauge . . . . . . . . . . . . . . . . . . . 308
Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . . 589
Engine Oil Viscosity Chart . . . . . . . . . . . . . . . . . 589
Enhanced Accident Response Feature . . . . . . . . . . 77
Entry System, Illuminated . . . . . . . . . . . . . . . . . . 23
Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 80
Exhaust Gas Caution . . . . . . . . . . . . . . . . . 48,98,515
Exhaust System . . . . . . . . . . . . . . . . . . . . . . . 98,599
Exterior Finish Care . . . . . . . . . . . . . . . . . . . . . . 615
Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 101
10
670 INDEX
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 587
Power Steering . . . . . . . . . . . . . . . . . . . . . . 464
Fluids, Lubricants and Genuine Parts . . . . . . . . . . 634
Fog Light Service . . . . . . . . . . . . . . . . . . . . . . . . 628
Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 303,628
Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . 174,177
Forward Collision Warning . . . . . . . . . . . 232,318,337
Four-Way Hazard Flasher . . . . . . . . . . . . . . . . . . 551
Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . . 571
Front Axle (Differential) . . . . . . . . . . . . . . . . . . . 609
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
Additives . . . . . . . . . . . . . . . . . . . . . . . . . . 514
Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Conserving . . . . . . . . . . . . . . . . . . . . . . . . . 323
Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Filler Cap (Gas Cap) . . . . . . . . . . . . . . . 519,522
Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Materials Added
Methanol . . . . .
Requirements . .
Saver Mode . . .
Tank Capacity . .
Fuel Optimizer . . . .
Fuel Saver . . . . . . . .
Fuel System Caution
Fuel, Flexible . . . . . .
Fuses . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
514
512
632
323
632
323
323
521
515
620
Garage Door Opener (HomeLink®) . . . . . . . . . . . 250
Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . 519,522,583
Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 511
Conserving . . . . . . . . . . . . . . . . . . . . . . . . . 323
Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . 512
Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 512
Gauges
Coolant Temperature . . . . . . . . . . . . . . . . . . 308
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
INDEX 671
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . 304
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . 299
Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . 433,441
Gear Select Lever Override . . . . . . . . . . . . . . . . . 573
General Information . . . . . . . . . . . . 20,29,153,229,510
Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 618
Gross Axle Weight Rating . . . . . . . . . . . . . . . 523,526
Gross Vehicle Weight Rating . . . . . . . . . . . . . 523,525
GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523
Hands-Free Phone (Uconnect™)
Hazard Warning Flasher . . . . .
Headlights . . . . . . . . . . . . . .
Bulb Replacement . . . . . .
Cleaning . . . . . . . . . . . . .
High Beam . . . . . . . . . . .
On With Wipers . . . . . . .
Replacing . . . . . . . . . . . .
Heated Mirrors . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
123
551
627
627
618
303
189
627
113
Heater, Engine Block
Hill Descent Control
Hill Start Assist . . .
Hitches
Trailer Towing .
Holder, Cup . . . . .
HomeLink® (Garage
Hood Release . . . .
. . . . . . . . . . . . . . . . . . . . . 429
. . . . . . . . . . . . . . . . . . . . . 304
. . . . . . . . . . . . . . . . . . . . . . 474
...................
...................
Door Opener) Transmitter
...................
...
...
..
...
530
270
250
186
Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14,16
Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . 16
Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 23
Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 18
Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 81,82
Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . 489
Information Center, Vehicle . . . . . . . . . . . . . . . . . 309
Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 110
Instrument Cluster . . . . . . . . . . . . . . . . . . . . 298,299
10
672 INDEX
Instrument Panel and Controls . . . . . . . . . . . . . . 297
Instrument Panel Lens Cleaning . . . . . . . . . . . . . 619
Integrated Power Module (Fuses) . . . . . . . . . . . . 620
Interior Appearance Care . . . . . . . . . . . . . . . . . . 617
Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 199
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Inverter, Power . . . . . . . . . . . . . . . . . . . . . . . . . 268
Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . 553
Jack Operation . . . . . . . . . . . . . . . . . . . . . . . 552,559
Jacking Instructions . . . . . . . . . . . . . . . . . . . . . . 559
Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . 567
Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . . 18
Key, Programming . . . . . . . . . . . . . . . . . . . . . . . . 20
Key, Replacement . . . . . . . . . . . . . . . . . . . . . . . . 19
Key, Sentry (Immobilizer) . . . . . . . . . . . . . . . . . . . 18
Keyless Enter-N-Go™ . . . . . . . . . . . . . . . . 38,326,425
Keyless Entry System . . . . . . . . . . . . . . . . . . . . . . 24
Keyless Go . . . . . . . . . . . . . . . . . . . . . . . . . . 14,326
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 52
LATCH (Lower Anchors and Tether
for CHildren) . . . . . . . . . . . . . . . . . . . . . . . . . 85,87
Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . . 511
Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Liftgate Window Wiper/Washer . . . . . . . . . . . . . 282
Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101,188
Airbag . . . . . . . . . . . . . . . . . . . . 74,75,80,99,305
Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Automatic Headlights . . . . . . . . . . . . . . . . . 189
Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . 630
Brake Assist Warning . . . . . . . . . . . . . . . . . . 477
Brake Warning . . . . . . . . . . . . . . . . . . . . . . 305
INDEX 673
Rear Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . 630
Bulb Replacement . . . . . . . . . . . . . . . . . . . . 627
Seat Belt Reminder . . . . . . . . . . . . . . . . . . . 307
Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Security Alarm (Theft Alarm) . . . . . . . . . . . . 305
Center Mounted Stop . . . . . . . . . . . . . . . . . . 631
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . 627
Daytime Running . . . . . . . . . . . . . . . . . . . . 191
Service Engine Soon
Dimmer Switch, Headlight . . . . . . . . . . . . . . 188
(Malfunction Indicator) . . . . . . . . . . . . . . . . 300
Electronic Stability Program (ESP) Indicator . . 477
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Side Marker . . . . . . . . . . . . . . . . . . . . . . . . 630
SmartBeams . . . . . . . . . . . . . . . . . . . . . . . . 190
Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303,628
Tire Pressure Monitoring (TPMS) . . . . . . . . . 299
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 620
Traction Control . . . . . . . . . . . . . . . . . . . . . 477
Hazard Warning Flasher . . . . . . . . . . . . . . . 551
Turn Signal . . . . . . . . . . . . . . . . 101,188,628,630
Headlights . . . . . . . . . . . . . . . . . . . . . . . . . 627
Vanity Mirror . . . . . . . . . . . . . . . . . . . . . . . 114
Headlights On With Wipers . . . . . . . . . . . . . 189
High Beam Indicator . . . . . . . . . . . . . . . . . . 303 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 523
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
Illuminated Entry . . . . . . . . . . . . . . . . . . . . . 23
Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 319 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Automatic Door . . . . . . . . . . . . . . . . . . . . . . 36
Malfunction Indicator (Check Engine) . . . . . . 300
Child Protection . . . . . . . . . . . . . . . . . . . . . . 36
Map Reading . . . . . . . . . . . . . . . . . . . . . . . 194
Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Reading . . . . . . . . . . . . . . . . . . . . . . . . 194,248
Rear Servicing . . . . . . . . . . . . . . . . . . . . . . . 630
Power Door . . . . . . . . . . . . . . . . . . . . . . . . . 35
10
674 INDEX
Lower Anchors and Tether for
CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . 85,87
Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 595
Luggage Rack (Roof Rack) . . . . . . . . . . . . . . . . . 284
Electric Remote . . . . . . . . . . . . . . . . . . . . . . 112
Exterior Folding . . . . . . . . . . . . . . . . . . . . . 112
Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Mode
Fuel Saver . . . . . . . . . . . . . . . . . . . . . . . . . 323
Modifications/Alterations, Vehicle . . . . . . . . . . . . . 9
Monitor, Tire Pressure System . . . . . . . . . . . . . . . 500
Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 585,658
MTBE/ETBE . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Multi-Displacement Engine System . . . . . . . . . . . 465
Multi-Function Control Lever . . . . . . . . . . . . . . . 188
Maintenance Free Battery . . . . . . . . . . . . . . . . . . 591
Maintenance Procedures . . . . . . . . . . . . . . . . . . . 586
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 638
Malfunction Indicator Light
(Check Engine) . . . . . . . . . . . . . . . . . . . . . . . 300,584
Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 659
Memory Feature (Memory Seat) . . . . . . . . . . . . . 182
Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Memory Seats and Radio . . . . . . . . . . . . . . . . . . 182
Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 325 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 97
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Automatic Dimming . . . . . . . . . . . . . . . . . . 110 Occupant Restraints . . . . . . . . . . . . . . . . . . . 48,73,77
Electric Powered . . . . . . . . . . . . . . . . . . . . . 112 Occupant Restraints (Sedan) . . . . . . . . . . . 70,71,73,76
INDEX 675
Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Off-Pavement Driving (Off-Road) . . . . . . . . . . . . 457
Off-Road Driving (Off-Pavement) . . . . . . . . . . . . 457
Oil Change Indicator . . . . . . . . . . . . . . . . . . . . . 322
Oil Change Indicator, Reset . . . . . . . . . . . . . . . . . 322
Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 632
Change Interval . . . . . . . . . . . . . . . . . . . . . 588
Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . 587
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 590
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 590
Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . 590
Identification Logo . . . . . . . . . . . . . . . . . . . 588
Materials Added to . . . . . . . . . . . . . . . . . . . 590
Recommendation . . . . . . . . . . . . . . . . . . 588,632
Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . 589
Viscosity . . . . . . . . . . . . . . . . . . . . . . . . 589,632
Onboard Diagnostic System . . . . . . . . . . . . . . 583,584
Opener, Garage Door (HomeLink®) . . . . . . . . . . . 250
Operator Manual (Owner’s Manual) . . . . . . . . . . . . 6
Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . 111
Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . 440,448
Overdrive OFF Switch . . . . . . . . . . . . . . . . . 440,448
Overhead Console . . . . . . . . . . . . . . . . . . . . . . . 248
Overheating, Engine . . . . . . . . . . . . . . . . . . . 308,551
Owner’s Manual (Operator Manual) . . . . . . . . . 6,659
Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614
Paint Damage . . . . . . . . . . . . . . . . . . . . . . . . . . 614
Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Park Sense System, Rear . . . . . . . . . . . . . . . . . . . 237
Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 465
Personal Settings . . . . . . . . . . . . . . . . . . . . . . . . 330
Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . 97
Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . 123
Phone, Hands-Free (Uconnect™) . . . . . . . . . . . . . 123
10
676 INDEX
Placard, Tire and Loading Information . . . . . . . . . 484
Polishing and Waxing . . . . . . . . . . . . . . . . . . . . . 615
Power
Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . 35
Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Lift Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Outlet (Auxiliary Electrical Outlet) . . . . . . . . 263
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 158,160
Steering . . . . . . . . . . . . . . . . . . . . . . . . 461,464
Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Tilt/Telescoping Steering Column . . . . . . . . . 203
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Pregnant Women and Seat Belts . . . . . . . . . . . . . . 66
Preparation for Jacking . . . . . . . . . . . . . . . . . . . . 558
Pretensioners
Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Programmable Electronic Features . . . . . . . . . . . . 330
Programming Transmitters
(Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 24
Quadra-Trac . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 491
Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . 408
Rain Sensitive Wiper System . . . . . . . . . . . . . . . . 201
Rear Air Conditioning . . . . . . . . . . . . . . . . . . . . 414
Rear Axle (Differential) . . . . . . . . . . . . . . . . . . . . 609
Rear Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Rear Cross Path . . . . . . . . . . . . . . . . . . . . . . . . . 120
Rear Cupholder . . . . . . . . . . . . . . . . . . . . . . . . . 270
Rear Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
Rear Park Sense System . . . . . . . . . . . . . . . . . . . 237
Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . 174,177
Rear Window Defroster . . . . . . . . . . . . . . . . . . . 283
Rear Window Features . . . . . . . . . . . . . . . . . . . . 282
Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 282
INDEX 677
Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 110
Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 164
Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 80
Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 540
Shifting into Transfer Case Neutral (N) . . . . . 543
Shifting out of Transfer Case Neutral (N) . . . . 546
Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 512
Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 594
Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . 65
Remote Control
Starting System . . . . . . . . . . . . . . . . . . . . . . . 29
Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . . . 24
Remote Sound System (Radio) Controls . . . . . . . . 406
Remote Starting System . . . . . . . . . . . . . . . . . . . . 29
Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . 626
Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 19
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 585
Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 496
Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 658
Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . 81
Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . 48
Retractable Cargo Area Cover . . . . . . . . . . . . . . . 280
Roll Over Warning . . . . . . . . . . . . . . . . . . . . . . . . 5
Roof Type Carrier . . . . . . . . . . . . . . . . . . . . . . . 284
Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 499
Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . 99
Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 101
Safety Defects, Reporting . . . . . . . . . . . . . . . . . . 658
Safety Information, Tire . . . . . . . . . . . . . . . . . . . 478
Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Safety, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . 48,98
Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 361
Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 638
Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . 65
Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52,99
Adjustable Upper Shoulder Anchorage . . . . . . 57
And Pregnant Women . . . . . . . . . . . . . . . . . . 66
10
678 INDEX
Child Restraint . . . . . . . . . . . . . . . . . . . 81,82,91
Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 619
Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . 60
Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Shoulder Belt Anchorage . . . . . . . . . . . . . . . . 57
Untwisting Procedure . . . . . . . . . . . . . . . . . . 56
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 163
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 617
Easy Entry . . . . . . . . . . . . . . . . . . . . . . . . . 185
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Power . . . . . . . . . . . . . . . . . . . . . . . . . . 158,160
Rear Folding . . . . . . . . . . . . . . . . . . . . . 174,177
Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Security Against Theft . . . . . . . . . . . . . . . . . . . . . 20
Security Alarm (Theft Alarm) . . . . . . . . . . . . . 20,305
Selection of Oil . . . . . . . . . . . . . . . . . . . . . . . . . 588
Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . 18
Sentry Key Programming . . . . . . . . . . . . . . . . . . . 20
Sentry Key Replacement . . . . . . . . . . . . . . . . . . . 19
Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 655
Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 657
Service Engine Soon Light
(Malfunction Indicator) . . . . . . . . . . . . . . . . . . . . 300
Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 659
Setting the Clock . . . . . . . . . . . . . . . . . . . . . 341,350
Settings, Personal . . . . . . . . . . . . . . . . . . . . . . . . 330
Shift Lever Override . . . . . . . . . . . . . . . . . . . . . . 573
Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
Automatic Transmission . . . . . . . . . . . . . . . . 430
Transfer Case, Shifting into Transfer
Case Neutral (N) . . . . . . . . . . . . . . . . . . . . . 543
Transfer Case, Shifting out of Transfer Case
Neutral (N) . . . . . . . . . . . . . . . . . . . . . . . . . 546
Short Message Service (SMS) . . . . . . . . . . . . . . . . 145
INDEX 679
Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Signals, Turn . . . . . . . . . . . . . . . . . . . 101,303,628,630
SmartBeams . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . 497
Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539
Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498
Spare Tire . . . . . . . . . . . . . . . . . . . . . . . 492,493,554
Specifications
Fuel (Gasoline) . . . . . . . . . . . . . . . . . . . . . . 511
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588
Speed Control (Cruise Control) . . . . . . . . . . . 205,208
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29,424
Automatic Transmission . . . . . . . . . . . . . . . . 424
Cold Weather . . . . . . . . . . . . . . . . . . . . 428,429
Engine Block Heater . . . . . . . . . . . . . . . . . . 429
Engine Fails to Start . . . . . . . . . . . . . . . . . . 428
Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Starting and Operating . . . . . . . . . . . . . . . . . . . . 424
Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 424
Steering
Power . . . . . . . . . . . . . . . . . . . . . . . . . . 461,464
Tilt Column . . . . . . . . . . . . . . . . . . . . . . 202,203
Wheel, Heated . . . . . . . . . . . . . . . . . . . . . . 204
Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . 202,203
Steering Wheel Audio Controls . . . . . . . . . . . . . . 406
Steering Wheel Mounted Sound System
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625
Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . 417,625
Storing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . 625
Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Sun Visor Extension . . . . . . . . . . . . . . . . . . . . . . 114
Sunglasses Storage . . . . . . . . . . . . . . . . . . . . . . . 250
Supplemental Restraint System - Airbag . . . . . . . . 67
Sway Control, Trailer . . . . . . . . . . . . . . . . . . . . . 474
10
680 INDEX
Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . 589
System, Remote Starting . . . . . . . . . . . . . . . . . . . . 29
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Telescoping Steering Column . . . . . . . . . . . . . 202,203
Temperature Control, Automatic (ATC) . . . . . . . . 408
Temperature Gauge, Engine Coolant . . . . . . . . . . 308
Tether Anchor, Child Restraint . . . . . . . . . . . . . . . 85
Text Messaging . . . . . . . . . . . . . . . . . . . . . . . . . 145
Tie Down Hooks, Cargo . . . . . . . . . . . . . . . . . . . 281
Tilt Steering Column . . . . . . . . . . . . . . . . . . . 202,203
Tire and Loading Information Placard . . . . . . . . . 484
Tire Identification Number (TIN) . . . . . . . . . . . . . 482
Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 478
Tire Safety Information . . . . . . . . . . . . . . . . . . . . 478
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 101,488,661
Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . 489
Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
Changing . . . . . . . . . . . . . . . . . . . . . . . . . . 552
Compact Spare . . . . . . . . . . . . . . . . . . . . . . 492
General Information . . . . . . . . . . . . . . . . . . 488
High Speed . . . . . . . . . . . . . . . . . . . . . . . . . 491
Inflation Pressures . . . . . . . . . . . . . . . . . . . . 489
Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552
Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . 495
Load Capacity . . . . . . . . . . . . . . . . . . . . 484,485
Pressure Monitor System (TPMS) . . . . . . . . . 500
Pressure Warning Light . . . . . . . . . . . . . . . . 299
Quality Grading . . . . . . . . . . . . . . . . . . . . . 661
Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
Replacement . . . . . . . . . . . . . . . . . . . . . . . . 496
Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478
Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . 498
Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . 554
Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . 494
Tread Wear Indicators . . . . . . . . . . . . . . . . . 494
INDEX 681
Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 532
Tow Hooks, Emergency . . . . . . . . . . . . . . . . . . . 573
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525,574
24-Hour Towing Assistance . . . . . . . . . . . . . 137
Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . 574
Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Recreational . . . . . . . . . . . . . . . . . . . . . . . . 540
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Towing Assistance . . . . . . . . . . . . . . . . . . . . . . . 137
Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . 468
Trailer Sway Control (TSC) . . . . . . . . . . . . . . . . . 474
Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 525
Cooling System Tips . . . . . . . . . . . . . . . . . . 539
Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530
Minimum Requirements . . . . . . . . . . . . . . . . 533
Trailer and Tongue Weight . . . . . . . . . . . . . . 532
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536
Trailer Towing Guide . . . . . . . . . . . . . . . . . . . . . 531
Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . . . 610
Electronically Shifted . . . . . . . . . . . . . . . . . . 450
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 610
Transmission
Automatic . . . . . . . . . . . . . . . . . . . . 432,440,611
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 611
Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
Transmitter Battery Service
(Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 27
Transmitter Programming
(Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 24
Transmitter, Garage Door Opener
(HomeLink®) . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Transmitter, Remote Keyless Entry (RKE) . . . . . . . . 24
Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 494
Turn Signals . . . . . . . . . . . . . . . . . . . . . . 303,628,630
UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . 364
Uconnect™ (Hands-Free Phone) . . . . . . . . . . . . . 123
10
682 INDEX
Uniform Tire Quality Grades . . . . . . . . . . . . . . . . 661
Universal Consumer Interface (UCI) Connector . . . 364
Universal Transmitter . . . . . . . . . . . . . . . . . . . . . 250
Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . 56
Upholstery Care . . . . . . . . . . . . . . . . . . . . . . . . 617
Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 328
Vehicle Certification Label . . . . . . . . . . . . . . . . . 523
Vehicle Identification Number (VIN) . . . . . . . . . . . . 8
Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . 485,523
Vehicle Modifications/Alterations . . . . . . . . . . . . . . 9
Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 417,625
Viscosity, Engine Oil . . . . . . . . . . . . . . . . . . . . . . 589
Voice Recognition System (VR) . . . . . . . . . . . . . . 153
Warning Flasher, Hazard . . . . . . . . . . . . . . . . . . 551
Warning, Roll Over . . . . . . . . . . . . . . . . . . . . . . . . 5
Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 8
Warranty Information . . . . . . . . . . . . . . . . . . . . . 658
Washers, Windshield . . . . . . . . . . . . . . . . . . 198,598
Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 615
Waxing and Polishing . . . . . . . . . . . . . . . . . . . . . 615
Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 616
Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 616
Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 45,262
Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 416
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Windshield Defroster . . . . . . . . . . . . . . . . . . . . . 100
Windshield Washers . . . . . . . . . . . . . . . . . . . . . . 198
Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 598
Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 596
Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 198
Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . 199
Wipers, Rain Sensitive . . . . . . . . . . . . . . . . . . . . 201
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained personnel.
The following must be observed during installation.
The positive power connection should be made directly to
the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the roof
or the rear area of the vehicle. Care should be used in
mounting antennas with magnet bases. Magnets may affect
the accuracy or operation of the compass on vehicles so
equipped.
The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interference between the communications equipment and the
vehicle’s electronic systems.
2012 Durango
2012
OWNER’S MANUAL
Chrysler Group LLC
12WD01-126-AF
Sixth Edition
Printed in U.S.A.
Durango
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement