Satisfy Professional's Needs Combination Hammer 32mm (1-1/4") HR3210FCT, HR3210C, HR3200C Comparison of Efficiency Note: 1. It may differ under some conditions. 2. Numbers in the charts below are relative values when the capacities of Competitor "B" are indexed at 100. 1 SDS- plus 32mm Drilling Test conditions: Drilled in concrete with compressive strength of 40N/mm2 . Bit diameter: 18mm Photo : HR3210C 135 Makita HR3210C 105 Makita HR3000C Competitor "B" Learned from the Mother Earth 120 Competitor "H" 100 slow 0 100 120 140 160 fast Bit diameter: 22mm Makita HR3210C 170 Makita HR3000C 170 135 Competitor "H" Competitor "B" Photo : HR3200C 100 slow 0 2 100 120 140 160 fast Chipping Test conditions: Chipped concrete with compressive strength of 40N/mm2. 145 Makita HR3210C 140 Makita HR3000C 115 Competitor "H" Competitor "B" Photo : HR3210C Combination Hammer Double Insulation Variable Speed Electronic Speed Control Soft Start Torque Limiter SDS-Plus Shank Carrying Case Built-in Job Light (HR3210FCT only) 100 small 0 100 120 140 HR3210FCT / HR3210C / HR3200C 32mm (1-1/4") Continuous rating Input Max. bit dia. Max. core bit dia. Impacts per minute (ipm) No load speed (rpm) Dimensions (L x W x H) Net weight Power supply cord HR3210FCT 850W 32mm (1-1/4") 90mm (3-1/2") 1,650-3,300 315-630 424 x 114 x 239mm (16-3/4" x 4-1/2" x 9-3/8") 5.0kg (11.0lbs) 5.0m (16.4ft) 160 large 350 HR3210C 850W 32mm (1-1/4") 90mm (3-1/2") 1,650-3,300 315-630 398 x 114 x 239mm (15-5/8" x 4-1/2" x 9-3/8") 4.8kg (10.6lbs) 5.0m (16.4ft) HR3200C 850W 32mm (1-1/4") 90mm (3-1/2") 1,650-3,300 315-630 398 x 108 x 239mm (15-5/8" x 4-1/4" x 9-3/8") 4.4kg (9.7lbs) 5.0m (16.4ft) Standard Equipment Quick Change Drill Chuck Set (HR3210FCT only), Depth Gauge, Side Grip, Bit Grease (Tool does not come with bit.) Makita Power Tools India Pvt. Ltd. Unit II Sy. Nos. 93/3 & 93/4, Koralur village, Kasaba Hobli, Hoskote Taluk, Bangalore - 560 067, INDIA. Tel: +91 80 2854 9008, Fax: +91 80 2854 9007 Email: [email protected] Website: www.makita.in Hammering with Rotation Rotation Hammering Powerful Impact Energy: 5.5J Vibration Level with AVT: 10m/s2 A n t i - V i b r a t i o n Te c h n o l o g y (HR3210C and HR3210FCT only) Learned from the Mother Earth How to generate How to manage How to bring you Photo : HR3210C POWER VIBRATION COMFORT Forcible Dr illing and C hipping wit h Ultra- Low V i b r a t ion Principle of Dynamic Vibration Absorber Rotation 3 Hammering 24 Angle Settings of Chisel bit Hammering with Rotation 3 mode Combination Hammer HR3210FCT Hammering Quick Change Chuck MODE Simple Single-Lever Control for Changing Operation Mode THE MOTHER EARTH SOMETIMES QUAKES. MAKITA's "Active" Dynamic Vibration Absorber shift of air pressure in crank room and barrel room "actively" controls balancer to move opposite of piston. Balancer Piston Balancer Air Piston Sleeve No Hammering while Idling ensures machine's long life. Hammering with Rotation Rotation Rubberized Soft Grip provides more control and comfort while minimizing hand fatigue and pain. LED job light Active Dynamic Vibration Absorber Vibration Absorbing Grip Striker Air Striker Air Air Piston Air HR3210C Reinforcing bar Torque Limiter Piston when drill bit hits against reinforcements, Torque Limiter operates to stop. Spring Change Lever in protected position for reduced possibility of breakage even if the machine is carelessly down to rest. Vibration Absorbing Grip spring loaded hinged grip absorbs vibration 24 Angle Settings of Chisel bit Hinge 40min 60min 80min 100min 10.0m/s 14.5m/s 16.5m/s 2 Competitor B 2 Vibration level 10m/s2 Active Dynamic Vibration Absorber Vibration Absorbing Grip 15m/s2 20m/s2 HR3200C Time to reach ELV 120min 57min 44min 2 Competitor H protects commutator and indicates time for maintenance. features twice as long as that of Predecessor model by employing large carbon brush. Comparison of Vibration level* and Time to reach ELV (Exposure Limit of Vibration)** 20min Auto Cut-Out Carbon Brush Longer life of Carbon brushes See the Result of AVT HR3210C HR3210FCT 25m/s2 *It is known as the tri-axial value and value at Directive of A(8). **It means the maximum amount of vibration that an operator may be exposed to on any single day. SDS-Plus Shank Slide Chuck :: push-in and Go :: slide-back and Pull Electronic control features Variable speed control by dial Constant speed control, Soft Start variable speed control LED lamp for indication of "Green" :: being electrified of "Blinking Red" :: replacing of carbon brush Tool does not come with bit.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project