SERIES

Add to my manuals
38 Pages

advertisement

SERIES | Manualzz

Freight Allowed:

$400.00 or more

Thermoplastic L.E.D. exit sign

UL 924 Listed

Nicad Battery

Dual input - 120/277 VAC

Universal mounting

Single/Double face

UL listed for damp location

AC only or battery back-up

Red or green letters

Thermoplastic combination

UL 924 Listed

Lead-calcium Battery

Dual input - 120/277 VAC

Universal mounting

Remote capable for two heads

UL listed for damp location

Red or green letters

Thermoplastic emergency light

UL 924 Listed

Lead-calcium Battery

Dual input - 120/277 VAC

Impact resistant

UL Listed for damp location

Low voltage disconnect

Fully automatic, solid state

charger

August 08

SERIES

UL 924

LISTED

MON-X-AC-R

MON-X-AC-G

MON-X-SP-R

MON-X-SP-G

MON-COM-R

MON-COM-R-RC

MON-COM-G

MON-COM-G-RC

MON-EMER

S

I

I

S

I - MINI

STANDARD TRANSFER CENTRAL INVERTER and DC BACKUP POWER SUPPLY COMBINATION UNIT

Single-Phase power system for incandescent, fluorescent and low voltage emergency lighting

.

Pure sine wave AC Power

12 or 24 volt DC output

300/400 Watts DC power

300/400 VAC power

400 Watts AC and DC power combined

ETL listed to U.L. 924 Standards

High efficiency

High power factor

Compact, wall mounting

Maintenance free sealed batteries

Push button test switch and LED indicators

3 outputs: 2 DC and 1 AC

Short or open on any one output does not

effect the other two

DC output fuse indication

One year warranty, two year optional

FEATURES

Combo Unit: Combination Unit capable of supplying 400 watts DC, 400 VAC or 400 watts of AC and DC power combined

Power Protection: All inverter units come with over and under voltage protection, over load protection, short circuit protection and reverse polarity protection.

Simple and Easy Installation: There is no special wiring required. Just connect the unit to either 120 or 277 volt incoming supply on the primary side and snap the male and female battery connector together and you are ready to go.

Reduced Maintenance and Service cost: Having an inverter and DC power in one unit allows you to install either low voltage emergency or standard fluorescent lights on the same unit thus eliminating the need for maintaining or testing each unit separately.

Pedestal Mounting: A pedestal mount places the unit near the equipment that needs to be supplied with emergency power.

All specifications subject to change without notice.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

I

S

I - MINI

STANDARD TRANSFER CENTRAL INVERTER and DC BACKUP POWER SUPPLY COMBINATION UNIT

Single-Phase power system for incandescent, fluorescent and low voltage emergency lighting

.

SPECIFICATIONS

INPUT

Voltage: 120 or 277 volt AC

Frequency: 60/50 Hz

Input voltage variation: +10%

OUTPUT

Power: 300/400 watt DC at 12 or 24

volt, 300/400 watt AC at 120/277 volt

Output regulation: +5%

Voltage waveform: Pure sine

PROTECTION

Battery over and under voltage

Overload and short circuit protection

Reverese polarity protection

Over temperature protection

OTHER SPECS

Transfer time: 6 (ms)

Battery run time: 90 minutes standard, other run times available on request

Battery recharge time: per U.L. 924

Width: 18 inches

Height: 15 inches

Depth 8 inches

Weight: Approx. 50-100 lbs, depending on the model

Finish: Powder coat white (standard)

Battery Volmeter and Ammeter

OPTIONS

Time Delay Relay

Emergency Lighting Heads

Remote Test Switch

Special Color

All specifications subject to change without notice.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

I

S

I - IPS3

STANDARD TRANSFER CENTRAL INVERTER

The Inverter Systems, Inc. IPS3 central inverters represent the state-of-the-art in central inverter technology. Onboard micro-processors control all system functions and provide the user with information concerning operation of critical system functions. The inverter design utilizes the latest PWM/IGBT technology for efficiency and reliability.

Systems are floor mounted, convection cooled and mounted in heavy gauge sheet metal cabinets requiring front access only. Key-locked doors are supplied for added security and safety. Each cabinet contains knockouts for interwiring with BX, Romex, or conduit. Systems 4.8kVA and below are self-contained while larger systems require external, stackable battery cabinets to house the batteries which supply 90 minutes of emergency run time.

OPERATION

The AC utility shall power the load through an electromechanical switch with a 10000 AIC rating. A Bi-directional transformer shall also power the battery charger, which in turn charge the batteries. Instantaneously after a utility power failure or utility brownout condition, the solid state driven transfer switch will disconnect the AC utility from the load, start the inverter and connect the load to this energy storage transformer. The maximum interruption to the load for this transition shall be 50 millisecond maximum. The inverter will power the load with a low distortion sine wave form, simulating the AC utility, After the AC utility returns, the transfer switch shall reconnect the AC utility to the load with a 50 millisecond maximum interruption and the battery charger shall automatically recharge the batteries. Complete load protection from overload or over voltage shall be accomplished via the on-board microprocessor. This method provides maximum load protection from any IPS3 failure mode.

This inverter shall be designed with a microprocessor that control IGBT transistors and generates a sinusoidal pulse width modulation (PWM) output. All magnetic (transformers, chokes, etc.) used within the inverter shall be constructed from

UL class H materials. The battery charger shall include a full wave bridge rectifier. It shall be of solid state construction and provide two rates of charge. This charger shall provide a constant voltage, current limited charge. Recharge time shall be

24 hours maximum.

STANDARD FEATURES:

Available in standard capacities from 1500 VA to 16.7 kVA

Modular design provides electronic assemblies mounted.

98% high-efficiency off-line operation

State of the art IGBT technology.

Short-circuit protected.

Standard front panel instrumentation includes, indicators: battery charging, battery power, AC line present, system ready; metering: input voltage, output voltage, battery voltage, battery current, AC output current; and system test switch.

Alarms: output fault, inverter fault, charger fault, high temperature, battery voltage, early warning

Maintenance free sealed lead calcium batteries are standard.

Special three phase combination systems available upon request.

Total harmonic distortion 6% or 3% any one occurrence or less for linear loads at unity power factor.

125% overload capability for 5 minutes in emergency mode.

Handles loads with power factors from .5 lag to .5 lead.

Output frequency regulation

±1% in emergency mode.

Precision multi-rate battery charger.

24 hour recharge for extended battery life.

Heavy gauge steel cabinets with filtered air louvers, key locks and removable hinged front opening doors for ease of access and maintenance.

System cooling by a fan and natural convection means.

Engineered for standard 90 minute emergency operation, extended run times available (consult factory).

Suitable for extreme temperature conditions from 0

° to +40°

C (continuous operation at high or low ambient temperatures may affect battery capacity and life, see battery warranty sheet for details).

New York City approved.

U.L. 924 listed.

All specifications subject to change without notice.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

ISI-IPS3

Model Capacity

VA

ISI-IPS3-1500

ISI-IPS3-2250

ISI-IPS3-3000

ISI-IPS3-3750

ISI-IPS3-4800

ISI-IPS3-6000

ISI-IPS3-8000

ISI-IPS3-10,000

ISI-IPS3-12,500

ISI-IPS3-16,700

98%

98%

98%

98%

98%

98%

98%

98%

98%

98%

Efficiency

@ full load

75

100

160

200

245

300

400

500

660

840

Heat

Loss

BTU’s

Inverter Cabinet

Dimensions (inches)

W H D

(A) (B) (C)

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

250

265

295

305

315

350

375

435

465

530

Weight

(lbs.)

Battery Cabinet

Dimensions (inches)

W H D

(D) (E) (F)

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

# Batt.

Cabinets

Required

--

--

1

2

2

--

--

--

2

3

Weight of add’l Batt.

Cabinets

(lbs.)

210

232

420

420

464

Total system shipping weight

(lbs.)

546

709

887

1045

1203

1670

2087

2631

3105

3954

SPECIFICATIONS:

The emergency lighting inverter system shall be a standard transfer (50ms) high efficiency off-line system suitable for sustaining and operating fluorescent and incandescent lamps in the event of a power outage for a minimum 90 minutes duration at the rated load and be listed and labeled to U.L. 924.

The entire system shall be of a modular construction with removable electronic modules for ease of installation and maintenance. Cabinets shall be constructed of code gauge steel with removable key locked hinged doors finished in an acid resistant enamel with a modified vinyl undercoat.

The inverter shall be solid state design with transistor power drive circuit for precision switching and maximum reliability with regulated Ferro resonant output transformer.

The AC input voltage shall be (120 or 277V single phase two wire plus ground).

The output voltage shall be provided as a) 120 or 277V single phase, two wire, or mixed 120V @(specify) VA, 277V @(specify) VA normally on, or b) 120 or 277V single phase two wire, or mixed 120V @(specify) VA, 277V @(specify) VA

normally off. The output frequency shall be 60HZ

±1HZ for all loads.

The system shall reliably handle from .5 leading to .5 lagging power factor. The output voltage regulation shall be

±4%. The system’s output shall be capable of

130% overload for 5 minutes. Harmonic distortion 3% total.

The battery charger is microprocessor controlled that continuously monitors and maintains the systems batteries and has a low voltage disconnect for long battery life. The charger shall fully recharge the batteries within the requirements of U.L.

924 specifications.

Self-Protective Features: Output short circuit protection with fail safe start-up, and reverse input polarity protection.

The system’s batteries shall be of the sealed maintenance free lead acid type.

Options: Refer to Option Selection Chart for descriptions and nomenclature.

Popular options are: Start-up Service, Input and Output Circuit Breakers G(1) and C

( ), Battery Exerciser and Variable Time Delay.

The system shall be an Inverter Systems model No.__________ as manufactured and warranted by Inverter Systems, Inc. (for copy of detailed specification format - consult factory).

ORDERING GUIDE:

When ordering an ISI-IPS3 inverter from Inverter Systems, Inc. use:

ISI-IPS3 - 6000 - 277 - 277 - G(1) - C(4) - SB - OPTIONS

1 2 3 4 5 6 7 8

2. Volt Amp (VA) Rating 1500 to 16,700

Select required capacity in volt amps from model tables above

3. Input Voltage

120V 2 wire plus ground

277V 2 wire plus ground

Other voltages (specify)

120

277

( )

4. Output Voltage

120V 2 wire plus ground

277V 2 wire plus ground

Other voltages (specify)

5. Input Circuit Breaker

120

277

( )

Specify input circuit breaker

6. Output Circuit Breakers

Specify number of output circuit

breakers (max. 10 per system)

7. Battery Type

G(1)

C( )

Maintenance free sealed lead acid SB

8. Options

Select requirements from Options Guide, popular options are:

Start-up service

Variable Time Delay

SUS

VTD

WARRANTY:

Electronics Assembly

Inverter Systems, Inc. warrants the ISI-IPS3 electronics assembly (except batteries) against defects in material and workmanship for a period of one year from date of shipment. Inverter Systems, Inc. will either repair or replace any properly installed ISI-IPS3 system which fails under normal operating conditions provided that it is returned to the factory, transportation prepaid, and our inspection determines it to be defective under the terms of this warranty.

The warranty covers only equipment other than batteries manufactured by Inverter Systems, Inc. and does not extend to transportation, installation or replacement charges, nor does it apply to any other equipment of another manufacturer used in conjunction with ISI equipment. No other warranty expressed or implied exists beyond that included in this statement.

Battery Warranty

Sealed lead calcium batteries carry a 1 year full, 10 year pro-rated limited warranty.

Important note: Battery warranty is limited to certain environmental, operational and installation limitations (refer to detailed Battery Warranty Terms and Conditions).

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

I

S

I - FTW

STAND-BY SINGLE PHASE AC SINE WAVE, LOW CAPACITY,

WALL MOUNTED UNINTERRUPTIBLE CENTRAL SYSTEM

The Inverter Systems, Inc. ISI-FTW provides a high efficiency single phase “stand-by” central AC emergency power system ideally suited for H.I.D., fluorescent and incandescent emergency lighting applications or other auxiliary loads that require a “fast transfer, no-break” voltage regulated and line conditioned power supply.

The ISI-FTW demonstrates exceptional 98% operating efficiency by means of the fast “no-break” transfer circuit, providing considerable running cost savings over typical double conversion UPS systems. Available in a wide range of voltages and four different capacities, the ISI-FTW is designed to provide up to 90 minutes of standby emergency power in accordance with the requirements of U.L. 924.

OPERATION

The inverter is normally off and the commercial AC power continuously supplies the critical load. The input converter

(bi-directional transformer) derives power from the commercial AC power source and supplies to the inverter while simultaneously providing floating charge to the batteries.

Upon failure of the commercial AC power the inverter instantaneously, with a maximum of a 2-millisecond break, switches its power supply from the input converter to the battery system. There shall be no loss of power to the critical load upon failure or restoration of the utility source.

An automatic low voltage cutoff circuit disengages the inverter system at the useful end of the battery capacity preventing deep discharge battery damage. Upon restoration of the utility supply the system automatically returns to the normal

“standby” mode and restores the battery to full charge.

STANDARD FEATURES:

PWM/MOSFET Inverter Technology for high efficiency and low THD

UL 924 listed and meets or exceeds the requirements of

OSHA for emergency lighting and power. NFPA70,

NFPA101, NFPA110, UBC, and SBCCI and New York

City approved

98% efficient in standby mode means no fan for cooling

Compatible with HID, fluorescent, incandescent, and electronic low voltage lighting

Maintenance-free, sealed lead calcium valve regulated lead acid batteries

Field upgradeable from 500VA to 2000VA by additional battery modules

Protection circuit breakers are battery, Input and Output

Front panel interface: Microprocessor controlled, 2x20 character display with touch pad controls

Programmable set points are password-controlled with user and service levels

Standard Alarms: Output, High Temp, Near Low Battery,

Inverter, Load Reduction, Low Voltage, Charger, Overload,

High Voltage, Low Battery, Overload Shutdown

Digital metering indicates: input voltage, output voltage, current output, battery voltage, system days, date, inverter minutes, ambient temperature, battery current, inverter watts, VA output

Diagnostic Features: User programmable with password protection for alarms and diagnostics, Self testing and diagnostic with event, test and alarm logs; Standard logs: alarm log (75), event log (75), test log (50)

Small footprint, both inverter and battery unit each measure

26”W x 10”H x 10”D

Floor or wall-mounted

16AWG (.059”) steel construction with powder coat surface

Modular design allows separation of inverter and battery modules

Electrical knockouts for easy contractor connection and installation

Circuit breaker and fuse access panel for easy routine maintenance

All specifications subject to change without notice.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

ISI-FTW

Model Capacity

VA

Efficiency

@ full load

ISI-FTW-500

ISI-FTW-1000

ISI-FTW-1500

ISI-FTW-2000

98%

98%

98%

98%

90 min.

Average

Battery current

13.5 ADC

26.5 ADC

40 ADC

52 ADC

Inverter Cabinet

Dimensions (inches)

W H D

(A) (B) (C)

Battery Cabinet

Dimensions (inches)

W H D

(D) (E) (F)

26 10 10

26 10 10

26 10 10

26 10 10

26 10 10

26 10 10

26 10 10

26 10 10

# Batt.

Cabinets

Required

1

2

3

4

*Current

Input

(amps)

*Current

Output

(amps)

5.2 / 1.8

10.5 / 3.61

15.62 / 5.42

20.8 / 7.22

4.16 / 1.8

8.33 / 3.61

12.5 / 5.41

16.66 / 7.22

Total system shipping weight

(lbs.)

206

335

464

592

*Current input reflects system at maximum charge current plus maximum load current

SPECIFICATIONS:

The emergency lighting inverter system shall be an stand-by no-break system suitable for sustaining and operating H.I.D., fluorescent and incandescent lamps in the event of a power outage for a minimum 90 minutes duration at the rated load and be listed and labeled to U.L. 924.

The entire system shall be of a modular construction with removable electronic modules for ease of installation and maintenance. Cabinets shall be constructed of code gauge steel with removable key locked hinged doors finished in an acid resistant enamel with a modified vinyl undercoat.

The inverter shall be a standby UPS. PWM inverter type utilizing MOSFET technology with 2mS transfer time.

The AC input voltage shall be (120 or 277V single phase two wire plus ground).

The output voltage shall be provided as a) 120 or 277V single phase, two wire

normally on, or b) 120 or 277V single phase, two wire or mixed 120V @(specify)

VA, 277V @(specify) VA normally off. The output frequency shall be 60HZ

±

0.05HZ for all loads.

The system shall reliably handle from .5 leading to .5 lagging power factor. The output voltage regulation shall be

±3% or better from 0% to 100% of rated load.

The system’s output shall be capable of 115% overload indefinitely, 125% for five minutes. Harmonic distortion <10% total or 3% any single harmonic.

The battery charger, in the standard configuration shall convert AC voltage to DC voltage. With commercial power present, the inverter power transformer is powered and the bidirectional MOSFET recharges the batteries. Once the batteries have received full recharge, a constant trickle charge maintains batteries at maximum level. Recharge time is 24 hours maximum at nominal AC input voltage.

The AC ripple current of the DC output meets the battery manufacturer specification, ensuring maximum life.

The system’s batteries shall be of the (sealed maintenance free lead acid) type.

Options: Refer to Option Selection Chart for descriptions and nomenclature.

Popular options are: Start-up Service, Output Circuit Breakers, Remote Meter

Panel, Output Trip Alarms

The system shall be an Inverter Systems model No.__________ as manufactured for and warranted by Inverter Systems, Inc. (for copy of detailed specification format - consult factory)

ORDERING GUIDE:

When ordering an ISI-FTW from Inverter Systems, Inc., use:

ISI-FTW - 500 - 277 - 277 - C(4) - SB - OPTIONS

1 2 3 4 5 6 7

1. Model Series ISI-FTW

2. Volt Amp (VA) Rating 500 to2000

Select required capacity in volt

Amps from model tables above

3. Input Voltage

120V 2 wire plus ground 120

277V 2 wire plus ground 277

Other voltages (specify) ( )

4. Output Voltage

120V 2 wire plus ground 120

277V 2 wire plus ground 277

Other voltages (specify) ( )

5. Output Circuit Breakers

Specify number of output circuit C( )

Breakers (maximum 2 per system)

6. Battery Type

Maintenance free sealed lead acid SB

7. Options

Select requirements from Options Guide,

Popular options are:

Start-up Service SUS

Output Trip Alarm OTA

Summary Dry Contacts (Form “C”) DCS

Remote Meter Panel RMP

WARRANTY:

Electronics Assembly

Inverter Systems, Inc. warrants the ISI-FTW electronics assembly (except batteries) against defects in material and workmanship for a period of one year from date of shipment. Inverter Systems, Inc. will either repair or replace any properly installed ISI-FTW system which fails under normal operating conditions provided that it is returned to the factory, transportation prepaid, and our inspection determines it to be defective under the terms of this warranty.

The warranty covers only equipment other than batteries manufactured by Inverter Systems, Inc. and does not extend to transportation, installation or replacement charges, nor does it apply to any other equipment of another manufacturer used in conjunction with ISI equipment. No other warranty expressed or implied exists beyond that included in this statement.

Battery Warranty

Sealed lead calcium batteries carry a 1 year full, 9 year pro-rated limited warranty.

Important note: Battery warranty is limited to certain environmental, operational and installation limitations (refer to detailed Battery Warranty Terms and Conditions).

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

I

S

I - UFT

STAND-BY SINGLE PHASE AC SINE WAVE UNINTERRUPTIBLE CENTRAL SYSTEM

The Inverter Systems, Inc. ISI-UFT provides a high efficiency single phase “stand-by” central AC emergency power system ideally suited for H.I.D., fluorescent and incandescent emergency lighting applications or other auxiliary loads that require a “fast transfer, no-break” voltage regulated and line conditioned power supply.

The ISI-UFT demonstrates exceptional 98% operating efficiency by means of the fast “no-break” transfer circuit, providing considerable running cost savings over typical double conversion UPS systems. Available in a wide range of capacities and voltages, the ISI-UFT is designed to provide up to 90 minutes of standby emergency power in accordance with the requirements of U.L. 924.

OPERATION

The inverter is normally off and the commercial AC power continuously supplies the critical load. The input converter

(bi-directional transformer) derives power from the commercial AC power source and supplies to the inverter while simultaneously providing floating charge to the batteries.

Upon failure of the commercial AC power the inverter instantaneously, with a maximum of a 2-millisecond break, switches its power supply from the input converter to the battery system. There shall be no loss of power to the critical load upon failure or restoration of the utility source.

An automatic low voltage cutoff circuit disengages the inverter system at the useful end of the battery capacity preventing deep discharge battery damage. Upon restoration of the utility supply the system automatically returns to the normal

“standby” mode and restores the battery to full charge.

STANDARD FEATURES:

Available in standard capacities from 1500 VA to 16.7 kVA

Modular design provides electronic assemblies mounted on removable modules for ease of maintenance

98% high-efficiency stand-by operation

Industry proven continuously on PWM inverter utilizes switching transistor failure whilst still maintaining full rated load output

Short-circuit protected with critical point fuses and breakers

Digital metering indicates: input voltage, output voltage, output frequency, output current, battery voltage, battery current, VA output, inverter watts, ambient temperature, system day, inverter minutes

System test switch

Available with many alarm function, monitoring and diagnostic options -refer Option Selection chart

Maintenance free sealed lead calcium batteries standard, wet nickel cadmium batteries optional

Heavy gauge steel cabinets with filtered air louvers, key locks and removable hinged front opening doors for ease of access and maintenance

Engineered for standard 90 minute emergency operation,

(extended run times available)

Suitable for extreme temperature from 0 to 40 C

(continuous operation at high or low ambient temperatures may affect battery capacity and life; see battery warranty sheet for details)

Input lighting protection meets IEEE/ANSI C62.45-45

(CAT A & B)

Input current harmonic distortion 10% or less at full load

Input circuit breaker included for complete protection

Load power factor .5 lag to .5 leading

Output distortion 3% THD linear load

U.L. 924 listed

All specifications subject to change without notice.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

ISI-UFT

Model Capacity

VA

ISI-UFT-1500

ISI-UFT-2250

ISI-UFT-3000

ISI-UFT-3750

ISI-UFT-4800

ISI-UFT-6000

ISI-UFT-8000

ISI-UFT-10,000

ISI-UFT-12,500

ISI-UFT-16,700

98%

98%

98%

98%

98%

98%

98%

98%

98%

98%

Efficiency

@ full load

300

400

500

660

840

75

100

160

200

245

Heat

Loss

BTU’s

Inverter Cabinet

Dimensions (inches)

W H D

(A) (B) (C)

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

350

375

435

465

530

250

265

295

305

315

Weight

(lbs.)

Battery Cabinet

Dimensions (inches)

W H D

(D) (E) (F)

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

# Batt.

Cabinets

Required

2

2

1

1

2

--

--

--

--

--

Weight of add’l Batt.

Cabinets

(lbs.)

210

232

420

420

464

Total system shipping weight

(lbs.)

546

709

887

1045

1203

1670

2087

2631

3105

3974

SPECIFICATIONS:

The emergency lighting inverter system shall be an stand-by no-break system suitable for sustaining and operating H.I.D., fluorescent and incandescent lamps in the event of a power outage for a minimum 90 minutes duration at the rated load and be listed and labeled to U.L. 924.

The entire system shall be of a modular construction with removable electronic modules for ease of installation and maintenance. Cabinets shall be constructed of code gauge steel with removable key locked hinged doors finished in an acid resistant enamel with a modified vinyl undercoat.

The inverter shall be a standby UPS. PWM inverter type utilizing IGBT technology with 2mS transfer time.

The AC input voltage shall be (120 or 277V single phase two wire plus ground).

The output voltage shall be provided as a) 120 or 277V single phase, two wire

normally on, or b) 120 or 277V single phase, two wire or mixed 120V @(specify)

VA, 277V @(specify) VA normally off. The output frequency shall be 60HZ

±

0.05HZ for all loads.

The system shall reliably handle from .5 leading to .5 lagging power factor. The output voltage regulation shall be

±3% or better from 0% to 100% of rated load.

The system’s output shall be capable of 125% overload for 5 minutes. Harmonic distortion <10% total or 3% any single harmonic.

The battery charger, in the standard configuration shall convert AC voltage to DC voltage. With commercial power present, the inverter power transformer is powered and the IGBT modules are microprocessor controlled to recharge the batteries.

The temperature compensated battery charger circuit supplies constant voltage and constant current to the batteries. Once the batteries have received full recharge, a constant trickle charge maintains batteries at maximum level. Recharge time is 24 hours maximum at nominal AC input voltage. The AC ripple current of the DC output meets the battery manufacturer specification, ensuring maximum life.

The system’s batteries shall be of the (sealed maintenance free lead acid) or (wet vented nickel cadmium) type.

Options: Refer to Option Selection Chart for descriptions and nomenclature.

Popular options are: Start-up Service, Output Circuit Breakers, Maintenance Bypass Switch, Output Trip Alarms

The system shall be an Inverter Systems model No.__________ as manufactured for and warranted by Inverter Systems, Inc. (for copy of detailed specification format - consult factory)

ORDERING GUIDE:

When ordering an ISI-UFT from Inverter Systems, Inc., use:

ISI-UFT - 8000 - 277 - 277 - C(4) - SB - OPTIONS

1 2 3 4 5 6 7

1. Model Series ISI-UFT

2. Volt Amp (VA) Rating 1500 to16700

Select required capacity in volt

Amps from model tables above

3. Input Voltage

120V 2 wire plus ground 120

277V 2 wire plus ground 277

Other voltages (specify) ( )

4. Output Voltage

120V 2 wire plus ground 120

277V 2 wire plus ground 277

Other voltages (specify) ( )

5. Output Circuit Breakers

Specify number of output circuit C( )

Breakers (maximum 10 per system)

6. Battery Type

Maintenance free sealed lead acid SB

Wet nickel cadmium NC

6. Options

Select requirements from Options Guide,

Popular options are:

Start-up Service SUS

Output Trip Alarm OTA

Summary Dry Contacts (Form “C”) DCS

Maintenance Bypass Switch MBYP

WARRANTY:

Electronics Assembly

Inverter Systems, Inc. warrants the ISI-UFT electronics assembly (except batteries) against defects in material and workmanship for a period of one year from date of shipment. Inverter Systems, Inc. will either repair or replace any properly installed ISI-UFT system which fails under normal operating conditions provided that it is returned to the factory, transportation prepaid, and our inspection determines it to be defective under the terms of this warranty.

The warranty covers only equipment other than batteries manufactured by Inverter Systems, Inc. and does not extend to transportation, installation or replacement charges, nor does it apply to any other equipment of another manufacturer used in conjunction with ISI equipment. No other warranty expressed or implied exists beyond that included in this statement.

Battery Warranty

Sealed lead calcium batteries carry a 1 year full, 9 year pro-rated limited warranty. Wet nickel cadmium batteries carry a 1 year full, 10 year pro-rated limited warranty.

Important note: Battery warranty is limited to certain environmental, operational and installation limitations (refer to detailed Battery Warranty Terms and Conditions).

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

I

S

I - 3UFT

STAND-BY THREE PHASE AC SINE WAVE UNINTERRUPTIBLE CENTRAL SYSTEM

The Inverter Systems, Inc. ISI-3UFT provides a high efficiency three phase “stand-by” central AC emergency power system ideally suited for H.I.D., fluorescent and incandescent emergency lighting applications or other auxiliary loads that require a “fast transfer, no-break” voltage regulated and line conditioned power supply.

The ISI-3UFT demonstrates exceptional 98% operating efficiency by means of the fast “no-break” transfer circuit, providing considerable running cost savings over typical double conversion UPS systems. Available in a wide range of capacities and voltages, the ISI-3UFT is designed to provide up to 90 minutes of standby emergency power in accordance with the requirements of U.L. 924.

OPERATION

The inverter is normally off and the commercial AC power continuously supplies the critical load. The inverter is normally off and the commercial AC power continuously supplies the critical load. The input converter (bi-directional transformer) derives power from the commercial AC power source and supplies to the inverter while simultaneously providing floating charge to the batteries.

Upon failure of the commercial AC power the inverter instantaneously, with a maximum of a 2-millisecond break, switches its power supply from the input converter to the battery system. There shall be no loss of power to the critical load upon failure or restoration of the utility source.

An automatic low voltage cutoff circuit disengages the inverter system at the useful end of the battery capacity preventing deep discharge battery damage. Upon restoration of the utility supply the system automatically returns to the normal

“standby” mode and restores the battery to full charge.

STANDARD FEATURES:

Available in standard capacities from 4.8kVA to 50 kVA.

Modular design provides electronic assemblies mounted on removable modules for ease of maintenance

98% high-efficiency stand-by operation

Industry proven continuously on PWM inverter.

Short-circuit protected with critical point fuses and breakers

Digital metering indicates: input voltage, output voltage, output frequency, output current, battery voltage, battery current, VA output, inverter watts, ambient temperature, system day, inverter minutes

System includes an internal manual maintenance bypass switch, used to power load direct from utility isolating the inverter system

System test switch

Comes standard with many alarm function, monitoring and diagnostic features

Maintenance free sealed lead calcium batteries standard.

Heavy gauge steel cabinets with filtered air louvers, key locks and removable hinged front opening doors for ease of access and maintenance

Engineered for standard 90 minute emergency operation,

(extended run times available)

Suitable for extreme temperature from 20º to 30º C

(continuous operation at high or low ambient temperatures may affect battery capacity and life; see battery warranty sheet for details)

Input lighting protection meets IEEE/ANSI C62.45-45

(CAT A & B)

Input current harmonic distortion 10% or less at full load

Input circuit breaker rated at 22k AIC minimum

Load power factor .5 lag to .5 leading

Output distortion 3% THD linear load

U.L. 924 Listed

Front Battery Access

All specifications subject to change without notice.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

ISI-3UFT

Model Capacity

VA

ISI-3UFT-4800

ISI-3UFT-6000

ISI-3UFT-8000

ISI-3UFT-10000

ISI-3UFT-12500

ISI-3UFT-16700

ISI-3UFT-24000

ISI-3UFT-33000

ISI-3UFT-40000

ISI-3UFT-50000

Efficiency

98

98

98

98

98

98

98

98

98

98

Heat

Loss

BTU’s

326

408

544

680

860

1136

1632

2244

2720

3400

Inverter Cabinet

Dimensions (Inches)

W H D

(A) (B) (C)

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

44 72 31

44 72 31

44 72 31

44 72 31

SPECIFICATIONS:

The emergency lighting inverter system shall be an on-line no-break system suitable for sustaining and operating H.I.D., fluorescent and incandescent lamps in the event of a power outage for a minimum 90 minutes duration at the rated load and be listed and labeled to U.L. 924.

The entire system shall be of a modular construction with removable electronic modules for ease of installation and maintenance. Cabinets shall be constructed of code gauge steel with removable key locked hinged doors finished in an acid resistant enamel with a modified vinyl undercoat.

The inverter shall be a continuously on solid state pulse width modulated type \ providing “no-break” regulated and line conditioned power supply. The PWM inverter shall feature internal redundancy allowing up to 20% switching transistor failure whilst still maintaining full rated load output capacity.

The AC input voltage shall be (120/208 or 277/480 three phase four wire plus ground).

The output voltage shall be provided as (120/208 or 277/480 three phase, four wire

normally on). Specify if normally off output is required. The output frequency shall be 60HZ

±1HZ for all loads.

The system shall reliably handle from .5 leading to .5 lagging power factor. The output voltage regulation shall be

±6% or better from 0% to 100% of rated load.

The system’s output shall be capable of 115% overload for 5 minutes. Harmonic distortion 3% any single harmonic.

The battery charger shall be of a dual rate design and feature a 90 day automatic equalization charge, low voltage disconnect and short circuit protected for long battery life. The charger shall fully recharge the batteries within the requirements of U.L. 924 specifications.

The system’s batteries shall be of the (sealed maintenance free lead acid) or (wet vented nickel cadmium) type.

Options: Refer to Option Selection Chart for descriptions and nomenclature.

Popular options are: Start-up Service, Output Circuit Breakers, Dry Summary

Contacts, Output Trip Alarms

The system shall be an Inverter Systems model No.__________ as manufactured and warranted by Inverter Systems, Inc. (for copy of detailed specification format - consult factory)

Weight

(lbs.)

535

535

535

639

639

639

1250

1250

1450

1450

Battery Cabinet

Dimensions (Inches)

W H D

(D) (E) (F)

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

30 47 25

48 72 31

48 72 31

48 72 31

48 72 31

No. Batt.

Cabinets

Required

2

2

1

2

1

1

1

2

2

2

Weight of

Additional

Batt. Cabinet lbs.

210

210

232

420

420

464

700

1300

1300

1400

Total

System shipping

Weight (lbs.)

1633

1855

2247

2835

3279

4063

6390

8630

10,160

11,980

ORDERING GUIDE:

When ordering an ISI-3UFT from Inverter Systems, Inc., use:

ISI-3UFT - 16700 - 277/480 - 277/480 - C(4) - SB - OPTIONS

1 2 3 4 5 6 7

1. Model Series ISI-3UFT

2. Volt Amp (VA) Rating 4800 to 50000

Select required capacity in volt

Amps from model tables above

3. Input Voltage

120/208 four wire plus ground 120/208

277/480 four wire plus ground 277/480

Other voltages (specify) ( )

4. Output Voltage

120/208 four wire plus ground 120/208

277/480 four wire plus ground 277/480

Other voltages (specify) ( )

5. Output Circuit Breakers

Specify number of output circuit C( )

Breakers (maximum 10 per system)

6. Battery Type

Maintenance free sealed lead acid SB

7. Options

Select requirements from Options Guide,

Popular options are:

Start-up Service SUS

Output Trip Alarm OTA

Summary Dry Contacts (Form “C”) DCS

(For additional options refer to Options Guide.)

WARRANTY:

Electronics Assembly

Inverter Systems, Inc. warrants the ISI-3UFT electronics assembly (except batteries) against defects in material and workmanship for a period of one year from date of shipment. Inverter Systems, Inc. will either repair or replace any properly installed ISI-3UFT system which fails under normal operating conditions provided that it is returned to the factory, transportation prepaid, and our inspection determines it to be defective under the terms of this warranty.

The warranty covers only equipment other than batteries manufactured by Inverter Systems, Inc. and does not extend to transportation, installation or replacement charges, nor does it apply to any other equipment of another manufacturer used in conjunction with ISI equipment. No other warranty expressed or implied exists beyond that included in this statement.

Battery Warranty

Sealed lead calcium batteries carry a 1 year full, 9 year pro-rated limited warranty. Wet nickel cadmium batteries carry a 1 year full, 10 year pro-rated limited warranty.

Important note: Battery warranty is limited to certain environmental, operational and installation limitations (refer to detailed Battery Warranty Terms and Conditions).

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

I

S

I - DC

12-120V DC CENTRAL POWER SYSTEMS

The Inverter Systems, Inc. ISI-DC Series offers a cost effective alternative to self contained battery emergency/ fluorescent power pack emergency lighting schemes and smaller AC inverters by providing a central DC power supply with which to feed incandescent lamps or fluorescent DC inverter modules enabling ease of monitoring and maintenance.

The ISI-DC is available in a wide range of capacities in

12, 24, 36, 48 and 120V DC output loads. Additionally, these systems are suited to other emergency loads such as burglar and fire alarm systems which require a “normally off” DC backup power supply. Standard systems are engineered to provide up to 90 minutes of standby DC emergency power in accordance with the requirements of U.L.

924 (other run times also available).

OPERATION

In the normal standby mode the utility AC maintains supply to the system’s isolation transformer, battery charger and central relays; no output is derived at the DC load. In the event of a utility supply failure or brownout condition the system’s relay sensors automatically connects the DC load to the battery bank, providing the rated DC load for the required duration.

Upon restoration of the utility supply the system automatically returns to the normal standby mode and restores the battery to full charge.

All specifications subject to change without notice.

STANDARD FEATURES:

Available in 12, 24, 36, 48 & 120 volt DC output from 500 to 10,000 watts

Modular design provides electronic assemblies mounted on

removable modules for ease of maintenance

Transfer time to full DC load 100ms

Precision multi-rated battery charger with automatic 90 day equalization feature maintains batteries at maximum capacity; internal LED indicators for charger status

24 hour recharge for extended battery life

Metering and controls include: battery DC voltmeter, input

AC voltmeter, utility power indicator, high charge indicator, battery charge ammeter with system test switch

Heavy gauge steel cabinets with filtered air louvers, key locks and removable hinged front opening doors for ease of access and maintenance

System cooling by natural convection means

Maintenance free sealed lead calcium batteries standard, wet nickel cadmium batteries optional

Engineered for standard 90 minute emergency operation,

(extended run times available)

Suitable for extreme temperature from 0

° - 40° C

(continuous operation at high or low ambient temperatures may affect battery capacity and life; see battery warranty sheet for details)

• Choice of full or zoned load switching

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

Model #

Capacity/VA

Rating

ISI-DC-12-500

ISI-DC-12-1000

ISI-DC-12-1500

ISI-DC-12-2000

ISI-DC-24-1000

ISI-DC-24-2000

ISI-DC-24-3000

ISI-DC-24-4000

ISI-DC-36-1500

ISI-DC-36-3000

ISI-DC-36-4500

ISI-DC-36-6000

ISI-DC-48-2000

ISI-DC-48-4000

ISI-DC-48-6000

ISI-DC-48-8000

ISI-DC-120-5000

ISI-DC-120-10000

Output

Watt

Rating

1500

3000

4500

6000

2000

4000

6000

8000

5000

10000

500

1000

1500

2000

1000

2000

3000

4000

Output

Voltage

VDC

48

48

48

48

36

36

36

36

120

120

24

24

24

24

12

12

12

12

Max. Utility

Input Current

@120VAC/277VAC

2 1

2 1

3 1.5

3 1.5

3 1.5

3 1.5

5 2.2

5 2.2

4 2

4 2

8 3.5

8 3.5

5 2.2

5 2.2

10 4.5

10 4.5

12 5.5

12 5.5

Heat

Loss

BTU’s

132

132

264

264

175

175

350

350

430

430

44

44

88

88

88

88

175

175

Cabinet Dimensions

(Inches)

W H D

(A) (B) (C)

32 33 12

32 33 12

42 38 12

42 38 12

32 33 12

42 38 12

42 50 12

42 50 12

42 38 12

42 50 12

42 50 12

42 62 12

42 50 12

42 50 12

42 62 12

42 50 19

42 50 19

42 70 19

System

Weight

(lbs.)

330

574

802

1028

438

718

1083

1303

943

1725

180

256

330

438

256

438

582

692

Battery

Voltage

VDC

48

48

48

48

36

36

36

36

120

120

24

24

24

24

12

12

12

12

Battery

Run

Time

Minutes

90

90

90

90

90

90

90

90

90

90

90

90

90

90

90

90

90

90

SPECIFICATIONS:

The emergency lighting standby power system shall be a non-maintained off-line

DC central power system suitable for incandescent lamps and fluorescent slave inverter module operation. In the event of a power outage the system shall provide the rated load and output DC voltage for 90 minutes duration.

The entire system shall be of a modular construction with removable electronic modules for ease of installation and maintenance. Cabinets shall be constructed of code gauge steel with removable key locked hinged doors and finished in an acid resistant enamel with a modified vinyl undercoat.

The DC system output voltage range shall be: Lead acid batteries=2.3V max.,

1.75V min. nominal 2 volts per cell; Nickel cadmium batteries=1.55V max., 1.05V min., nominal 1.2 volts per cell.

The nominal output voltage shall be (12,24,36,48 or 120) VDC “normally off” two wire.

The AC input voltage shall be (120 or 277V single phase two wire plus ground).

Battery charger shall be solid-state and of a dual rate design featuring a 90 day boost equalization charge, continuous trickle float charge with integral green, yellow and dual red LED mode indicators, automatic low battery voltage cut-off and reset upon utility return.

The charger shall fully recharge the batteries within the requirements of U.L. 924 specifications.

The system’s batteries shall be of the (sealed maintenance free lead acid) or (wet vented nickel cadmium) type.

Options: Refer to Option Selection Chart for descriptions and nomenclature.

Popular options are: Start-up Service, Digital Metering, Diagnostic Alarms and

Monitoring, Fused output circuits, Battery Exerciser and Charger Failure Alarm

The system shall be an Inverter Systems model No.__________ as manufactured and warranted by Inverter Systems, Inc. (for copy of detailed specification format - consult factory)

ORDERING GUIDE:

When ordering an ISI-DC Central emergency system, use:

ISI-DC - 12 - 500 - 120 - SB - OPTIONS

1 2 3 4 5 6

1. Model Series ISI-DC

2. Output Voltage VDC 12, 24, 36, 48 or 120

3. Output Watt Rating 500 to 10000

(Select from table above)

4. Input Voltage

120V 2 wire plus ground 120

277V 2 wire plus ground 277

Other voltages (specify) ( )

5. Battery Type

Maintenance free sealed lead acid SB

Wet nickel cadmium NC

6. Options

Select requirements from Options Guide,

Popular options are:

Start-up Service SUS

Charge Failure Alarm CFA

Output Monitor Alarm OMA

Diagnostic Microprocessor & Testing STDIAG

(For additional options refer to Options Guide.)

WARRANTY:

Electronics Assembly

Inverter Systems, Inc. warrants the ISI-DC electronics assembly (except batteries) against defects in material and workmanship for a period of one year from date of shipment. Inverter Systems, Inc. will either repair or replace any properly installed ISI-DC system which fails under normal operating conditions provided that it is returned to the factory, transportation prepaid, and our inspection determines it to be defective under the terms of this warranty.

The warranty covers only equipment other than batteries manufactured by Inverter Systems, Inc. and does not extend to transportation, installation or replacement charges, nor does it apply to any other equipment of another manufacturer used in conjunction with ISI equipment. No other warranty expressed or implied exists beyond that included in this statement.

Battery Warranty

Sealed lead calcium batteries carry a 1 year full, 9 year pro-rated limited warranty. Wet nickel cadmium batteries carry a 1 year full, 10 year pro-rated limited warranty.

Important note: Battery warranty is limited to certain environmental, operational and installation limitations (refer to detailed Battery Warranty Terms and Conditions).

Shipping

Weight

(lbs.)

405

6498

877

1103

513

793

1158

1378

1018

1800

255

331

405

513

331

513

657

767

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

WARRANTY

LIMITED WARRANTY TERMS & CONDITIONS

FOR CENTRAL POWER SYSTEMS

WARRANTY: Inverter Systems, Inc. (ISI) ISI-Series central power systems electronic assemblies (except batteries) are warranted against defects in material and workmanship from date of shipment EX-Works for a period of:

ISI-IPS3 Series = One Year

ISI-UFT Series = One Year

ISI-3UFT Series = One Year

ISI-DC Series = One Year

ISI-FTW Series = One Year

ISI’s warranty is limited to either repair or replacement of parts and equipment of PROPERLY INSTALLED ISI Series central power systems which fail under normal operating conditions PROVIDED that the system is properly packed for road transport and returned transportation prepaid to

ISI factory and ISI’s inspection determines it to be defective under the terms of this warranty. SUCH REPAIR OR REPLACEMENT SHALL

BE THE PURCHASER’S EXCLUSIVE REMEDY.

The warranty covers only equipment other than batteries manufactured, sold and warranted by ISI and does not extend to transportation, installation or replacement charges, nor does it apply to any other equipment of another manufacturer used in conjunction with ISI’s ISI

Series systems.

ISI’s warranty shall be null and void under the following conditions: a) Damage caused by abuse, misapplication, shipping damage, improper installation, or damage resulting from changes in circuitry or components made by other than authorized ISI personnel or service companies authorized by ISI. b)Damage due to improper maintenance. c) Damage resulting from installation(s) in areas with other than normal temperatures. Maximum ambient temperature must not exceed 90° F. d)Environmental conditions, damages caused by fire and abuse or acts of

God such as lightning, explosions, water leaks or acts of war are not covered by the warranty.

Replacement of fuses, pilot lights and lamps, and indicator lights and lamps, are not included in the Warranty. Warranties for batteries used in

ISI’s AC systems are described in the following paragraph.

Batteries included with the above ISI central power systems shall be

warranted as follows:

Type of Battery

Period of repair or replacement without charge

Period or Pro-rata charge for repair or replacement

Annual adjustment charge %

Maintenance free sealed

Wet nickel cadmium

1 year

1 year

9 years

10 years

7%

5%

Period) shall commence on the expiration of the Guarantee Period. All warranties set forth herein, whether during the Guarantee Period or the Prorata Charge Period, are subject to: a) The battery having been properly installed and continuously maintained in accordance with recommended practice together with documented history (both as set forth in the ISI installation manual relating to the battery involved and national and local requirements). b) The average ambient temperature shall not exceed 77°F. c) Cell temperatures shall not exceed 92°F for more than 30 days annually. d) Battery service records must be maintained every two months. e) The batteries have not bee contaminated by any foreign matter. f) Not more than 300 discharges of 80% or less of the ampere hour capacity are incurred. g) Batteries must be installed and placed on charge/energized within 120 days of shipment.

Should the battery fail to deliver 80% of its rated capacity or a defect appear in a battery covered by the warranty during the pro-rata charge period, on return of the defective battery transportation prepaid, ISI will repair or replace such battery at a cost equal to the net LIST prices at the time of repair or replacement, reduced by a percentage of such price equal to the product of the number of full years remaining in the warranty period at the time of the failure multiplied by 7% in the case of maintenance free sealed lead acid batteries and 5% in the case of nickel cadmium batteries.

Example:

Replacement list price = $100

Pro-rata warranty years remaining = 4

Annual adjustment charge = 7%

$100 less ($100 x .07 x 4) = $72 replacement charge

REPAIR OR REPLACEMENT AT SUCH ADJUSTED PRICE SHALL

BE PURCHASER’S EXCLUSIVE REMEDY.

In the event that the unit AC input is de-energized for an extended period, the battery circuit breaker or fuse must be turned off/disengaged so as to eliminate any current drain. The battery warranty will be void if the fuse or circuit breaker is not turned off within 36 hours after the unit is deenergized.

THE ISI SERIES SYSTEMS’ WARRANTY AND THE BATTERY WARRANTY

MENTIONED ABOVE ARE EXPRESSLY IN LIEU OF, AND THERE ARE NO OTHER

EXPRESS OR IMPLIED GUARANTEES OR WARRANTIES INCLUDING ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE THAT RELATE TO

THE PRODUCTS REFERRED TO HEREIN. IN NO EVENT WILL ISI BE LIABLE FOR

ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES WHICH

MAY RESULT FROM THE USE OF THESE PRODUCTS. ISI NEITHER ASSUMES NOR

AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILTY IN

CONNECTION WITH THE SALE OR RESALE OF SUCH PRODUCTS AND EXCEPT AS

STATED IN THEWARRANTIES, ISI SHALL NOT BE LIABLE FOR ANY DEFECT IN, OR

BREACH OF, ANY CONTRACT RELATING TO THE QUALITY OF, OR PERFORMANCE

OF, THE ISI SERIES SYSTEMS OR BATTERIES UNDER ANY THEORY OF LAW

INCLUDING, WITHOUT LIMITATION, CONTRACT, NEGLIGENCE, STRICT LIABILITY

OR MISREPRESENTATION.

The period noted above during which repair or replacement is without charge (the “Guarantee Period”) shall commence on the date of shipment.

The period of pro-rata charge for replacement or repair (the Pro-rata Charge

329 Otter Street, Bristol, PA 19007 USA

Telephone (215) 788-8870

Fax (215) 788-8873

I

S

I

August 08

EXCEL

L.E.D. EXIT SIGN

Premium quality sign ideal for commercial, institutional, and industrial facilities where economy, appearance, and ultimate ease of installation and maintenance are desired. The EXCEL (EXC) is also ideal when a low profile unit needs to meet limited space requirements, and any location requiring an exit sign.

FEATURES

Universal transformer for 120 or 277 VAC operation, dual voltage.

Push to test switch and charge rate/power on LED indicator light.

Premium batteries provide 90 minutes emergency light for red and green signs.

Remote test option available.

UV stable, high impact, injection molded, V-O flame resistant thermoplastic housing.

Universal mounting is standard for end, ceiling or wall application is standard.

Canopy included.

Universal pop out chevron directional arrows can be put back if desired.

Compact low profile design in neutral finish.

Easy quick installation.

Bright, even illumination, with either red or green letters.

Exceeds NFPA Life Safety Code 70 and 101 illumination requirements.

Complies with latest standard UL924. ETL listed. Meets Chevron codes.

LED FEATURES

Ultra bright maintenance free LED light source.

Premium Ni-Cad battery.

LED light source consumes only 1.03 watts.

95% savings compared to incandescent signs.

WARRANTY

All EXCEL fixtures are warranted to be free from manufacturing defects and workmanship for period of 10 years. The batteries are pro-rated for a 5 year period when operated at normal ambient temperatures.

SIGN SERIES OPERATION LETTER COLOR # OF FACES SIGN COLOR OPTIONS

EXC

EXCEL SERIES

AC

SP

90 MINUTE BACKUP

R

RED

G

GREEN

U

UNIVERSAL

WW

WHITE

BB

BLACK

SEE BELOW

OPTIONS AND ACCESSORIES

BZ Buzzer

SD Self Diagnostics

7.5”

FBZ

FR

RT

CP

Flasher and Buzzer Interface

Fire Alarm Flasher

(24V)

Remote Test Capability

(requires remote control)

Cord and Plug

(6’ Length)

12.5”

IRT

PEN

Infrared Remote Test Control

6” Pendant Mounting Kit

7.5”

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

1.75”

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

EXCEL-2

EMERGENCY LIGHT &L.E.D. EXIT SIGN COMBINATION

The EXCEL-2 (EXC2) combo is a great energy and cost saving approach to meeting egress lighting requirements. Commercial, retail and industrial facilities that require battery back-up emergency exit signs as well as emergency lighting.

FEATURES

Combo units include all the features of the EXCEL emergency lights and

exit signs.

Injection molded, V-O flame retardant, high impact, thermoplastic housing available in black or white.

Available with high powered 5 watt, MR-16 halogen lamps.

Meets or exceeds all state and local codes, tested and certified to

UL924,

ETL listed.

Ultra-bright LED lamps consume less than 2 watts.

LED lamp life is rated at 25 years.

Utilizes a premium Ni-cad battery.

OPERATION

Whenever normal utility power fails, the internal solid state transfer switch automatically connects the battery to the lamp heads providing a minimum of 90 minutes of light. When normal utility power is restored, recharging of the battery is initiated by an automatic, solid state, two-rate charger, which includes current limiting and temperature compensation to assure that optimum recharge is achieved. A fully discharged battery will be fully recharged within 12 hours.

# OF FACES SIGN SERIES

EXC2

EXCELSERIES

WATTS

11 27

18 32

HEAD TYPE

X

MR 16

WARRANTY

The EXCEL fixture and battery are warranted to be free from defects for a period of one year from date of purchase. The battery is covered by a 5 year pro-rated warranty.

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

COLOR

R

RED

G

GREEN

U

UNIVERSAL

12.75”

13.5”

SIGN COLOR

W

WHITE

B

BLACK

5.5”

13.5”

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

NAVIGATOR

EMERGENCY LIGHT & L.E.D. EXIT SIGN COMBINATION

Commercial, retail, and industrial facilities that require battery back-up emergency exit signs, as well as emergency lighting. The NAV combo is a great energy and cost saving approach to meeting egress lighting requirements.

FEATURES

Compact, low profile design in neutral finish.

Universal mounting canopy for side or top installation.

Built in conduit mounting feature is standard..

Two fully adjustable, glare free lighting heads with 5.6 watt lamps standard.

Universal snap in and out chevrons meet and exceed state and local codes.

Louvered down lighting.

Completely self contained.

Easy installation.

Injection molded, V-O flame retardant, high impact, thermoplastic housing.

Automatic low voltage disconnect (LVD) protects battery from deep discharge.

Environmentally coated, solid state charger.

Push to test switch.

Universal transformer for both 120V and 277V operation.

LED FEATURE

Super bright L.E.D. lamps consume only 3 watts.

Long 25 year rated L.E.D. lamp service life.

Premium Ni-Cad maintenance free battery with 10 year expected life.

WARRANTY

The NAVIGATOR fixture and battery are warranted to be free from defects for a period of one year from date of purchase.

The battery is covered by a 10 year pro-rated warranty.

MOUTING # OF FACES SERIES

NAV

NAVIGATOR

U

UNIVERSAL

LETTER COLOR

R

RED

G

GREEN

U

UNIVERSAL

SIGN COLOR

W

WHITE

B

BLACK

OPTIONS AND ACCESSORIES

RT

CP

IRT

PEN

Remote Test Capability (requires remote control)

Cord and Plug (6’ Length)

Infrared Remote Test Control

6” Pendant Mounting Kit

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to U.L. 924. ETL listed.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

MITIGATOR

ALUMINUM DIECAST L.E.D. EXIT SIGN

The MITIGATOR (MIT) is a premium architectural quality sign that is ideal for commercial, institutional, and industrial facilities. It is constructed of quality die-cast aluminum and pleases the eye. Available in all white, all black, or a brushed aluminum face on a black body.

FEATURES

Universal transformer for 120 or 277 VAC operation, dual voltage.

Simple installation / Universal with removable “CHEVRON” arrows.

Ultra bright low power L.E.D. light source.

Red or green letters evenly illuminated.

Isolated short circuit and voltage protection circuit.

AC only or optional self powered with N-Cad batteries.

L.E.D.’s shall carry a limited lifetime warranty / 5 years on

Ni-Cad batteries.

L.E.D. light source 1.03 watts

UL 924 listed, NFPA 101 Approved, ETL laboratories.

95% savings compared to incandescent signs.

WARRANTY

All MITIGATOR fixtures are warranted to be free from manufacturing defects and workmanship for period of 5 years. The batteries are pro-rated for a 5 year period when operated at normal ambient temperatures.

SIGN SERIES OPERATION OPTIONS

MIT

MITIGATOR SERIES

AC

SP

90 MINUTE BACKUP

LETTER COLOR # OF FACES

R

G

RED

GREEN

1

2

SIGN COLOR

WW

WHITE

BB

BLACK

BAL

BLACK W/

BRUSHED ALUM. FACE

SEE BELOW

OPTIONS AND ACCESSORIES

AL Brushed Aluminum Housing (see pricing)

BZ Buzzer

FL Flasher

FBZ Flasher and Buzzer Interface

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

12.75”

1.75”

8.5”

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

MASTER-REMOTE

LOW LEVEL L.E.D. EXIT SIGNS

Low level exit signs meet new code requirements for signage near the floor and adjacent to the egress doorway.

This system consists of two main components. A master sign above the door and a remote sign near the base of the door. The sign at the base of the door can be either surface or recessed mounted. MITIGATOR, STARK, and EXCEL series signs can be utilized in this system. All of the energy and maintenance characteristics of this LED configuration make for an extremely easy system to install and maintain.

FEATURES

L.E.D. signs are available with red or green lettering and meet the illumination

requirements of NFPA Life Safety Codes.

Low 3.5 watt total sign consumption exceeds Energy Star requirements.

95% or greater energy savings when compared to incandescent signs.

Master units are available with plastic, steel, or cast aluminum housings.

Remote units are available either as a surface mount or recessed housing fixture.

Remote unit can be mounted up to 12 feet from the master.

• Universal directional arrow meets new UL924 chevron requirements.

Dual voltage isolation transformer provides for 120 /277 volt circuits.

Push to test switch with LED indicator light is standard on all battery back-up signs.

Premium NiCad batteries provide 90 minutes of emergency illumination.

MASTER

REMOTE OPTIONS

WARRANTY

Warranted to be free from defects for 5 years.

Batteries are pro-rated for a 5 year period.

ORDERING INFORMATION:

Master Units refers to the sign above the door or passage way that is powered by the primary circuit.

Remote Units refers to the sign that is powered from the master unit.

MIT Series signs may be utilized as the “Master Unit.” This is true of both single and double sided signs with red or green lettering, also on both AC or battery back-up signs. To order a master unit please order as

MITMR-…

CK50 (recessed steel housing), EXC, and MIT Series signs can be utilized as “Remote Units.” Remote units are single sided signs. Because they are operated from the master unit, it is not necessary to order the

“SP” battery back-up option. To order a remote unit please suffix “-

RU”.

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

MITIGATOR-UNIVERSAL

ALUMINUM DIECAST L.E.D. EXIT SIGN WITH SINGLE OR DOUBLE FACE CAPABILITY

Premium architectural quality sign is ideal for commercial, institutional, and industrial facilities. It is constructed of quality die-cast aluminum and pleases the eye. Available in all white, all black, or a brushed aluminum face on a black body. The face plate is curved, producing a sleek appeal.

FEATURES

Universal transformer for 120 or 277 VAC operation, dual voltage.

Simple installation / Universal faces with removable “CHEVRON” arrows.

Ultra bright low power L.E.D. light source.

Red or green letters evenly illuminated.

Isolated short circuit and voltage protection circuit.

AC only or optional self powered with nickel cadmium batteries.

L.E.D.’s shall carry a limited lifetime warranty / 5 years on Ni-

Cad batteries.

L.E.D. light source 4 watts

UL 924 listed, NFPA 101 Approved, ETL laboratories.

All units damp rated.

95% savings compared to incandescent signs.

WARRANTY

All MITIGATOR fixtures are warranted to be free from manufacturing defects and workmanship for period of 10 years. The batteries are pro-rated for a 5 year period when operated at normal ambient temperatures.

SIGN SERIES

MIT-U

MITIGATOR

UNIVERSAL

SERIES

OPERATION

AC

SP

90 MINUTE BACKUP

LETTER COLOR

R

G

RED

GREEN

SIGN COLOR OPTIONS

WW

WHITE

BB

BLACK

BAL

BLACK W/

BRUSHED ALUM. FACE

2CKT

Dual Circuit

SD

Self Diagnostics

The MIT-U is an excellent alternative to traditional die-cast signs. Instead of stocking both single and double face signs, the MIT-U has a

“pop-off” back plate that can be replaced with an extra face plate.

Save space and money, by stocking singlefaced signs along with extra face plates.

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to U.L. 924. ETL listed.

12.75”

1.75”

8.5”

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

STARK

STEEL L.E.D. EXIT SIGN

The STARK (STA) Series features an attractive, contemporary steel housing design. Premium architectural quality makes this series ideal for commercial, institutional, and industrial facilities. Constructed with welded

20 gauge steel and is designed for both durability and economy.

FEATURES

Universal transformer for 120 or 277 VAC operation, dual voltage.

Simple installation / Universal with removable “CHEVRON” arrows.

Ultra bright low power L.E.D. light source.

Red or green letters evenly illuminated.

Isolated short circuit and voltage protection circuit.

AC only or optional self powered with nickel cadmium batteries.

L.E.D.’s shall carry a limited lifetime warranty / 5 years on Ni-

Cad batteries.

L.E.D. light source 1.03 watts

UL 924 listed, NFPA 101 Approved, ETL laboratories.

95% savings compared to incandescent signs.

WARRANTY

All STARK fixtures are warranted to be free from manufacturing defects and workmanship for period of 10 years. The batteries are pro-rated for a 5 year period when operated at normal ambient temperatures.

OPTIONS SIGN SERIES OPERATION LETTER COLOR

STA

STARK SERIES

AC

SP

90 MINUTE BACKUP

R

RED

G

GREEN

# OF FACES SIGN COLOR

U

UNIVERSAL

WW

WHITE

BB

BLACK

OPTIONS AND ACCESSORIES

BZ Buzzer

SEE BELOW

7.5”

RT Remote Test (requires infrared remote control)

FBZ

FR

CP

Flasher & Buzzer Interface

Fire Alarm Flasher (24 Volt)

6’ Cord & Plug

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

12.25”

2.25”

7.5”

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

PINNACLE

EDGELIT L.E.D. EXIT SIGN

The aesthetically appealing PINNACLE (PINN) edge lit exit sign is available in AC only or self powered units.

Energy saving LED’s consume less than 3 watts for AC only / less than 8 watts for self powered operation. 20 gauge epoxy coated steel back box. Mounting options include ceiling recessed, wall recessed, wall surface, or ceiling surface mount.

FEATURES

Clear acrylic panel with polished edges, aluminum or white separate

plates supplied with double faced exits.

Self powered version features sealed maintenance free nickel cadmium

battery with 7 year life expectancy.

AC lockout installation feature and low voltage disconnect.

AC indicator light and test switch, solid state charging circuitry, for

self powered units.

WARRANTY

All PINNACLE fixtures are warranted to be free from manufacturing defects and workmanship for a period of one

year. The batteries are pro-rated for a 5 year period when operated at normal ambient temperatures.

SIGN SERIES LETTER COLOR OPERATION

PINN

PINNACLE

SERIES

R

RED

G

GREEN

AC

SP

90 MINUTE

BACKUP

MOUNTING

CR

CEILING RECESSED

WR

WALL RECESSED

SC

SURFACE CEILING

SW

SURFACE WALL

FACES

1

2

BACKGROUND

C

CLEAR

W

WHITE

M

MIRROR

OPTIONS

SEE

BELOW

OPTIONS AND ACCESSORIES

BR Polished Brass Finish

BAL Brushed Aluminum Finish

PAL Polished Aluminum Finish

BZ Buzzer

FL Flasher

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

ENDUREX-1

SELF-LUMINOUS EXIT SIGN

The ENDUREX-1 (END1) series provides a contemporary design with a rugged, low profile molded thermoplastic housing. Highly economical, 100% reliable, exit sign… ENDUREX-1 requires, no wiring, batteries, maintenance, or electrical power. It is available in 10 to 20 year life spans. It is suitable for use in hazardous atmospheres and wet locations.

LIGHTING

Internally illuminated by sealed tritium gas light sources.

100% reliable: Requires no electrical power, wiring or

batteries, and no maintenance.

Green light output for maximum visibility in dark

conditions. No external light or power is required for

activation.

Lamps guaranteed for up to 20 years of continuous

operation.

Approved for ETL for minimum visibility of 100 ft.

in darkness by UL test standards.

CONSTRUCTION

One-piece ABS thermoplastic injection molded housing

only 7/8” thick, with clear polycarbonate window.

Sealed internal construction prevents unauthorized

access to light tubes.

Legend face is removable, allowing for quick installation

or adjustment of stencil face color, with universal

field-adjustable arrows.

Standard finishes are white or black housing, with white

lettering and high contrast red, green or black faceplate.

Optional finishes include many custom colors.

Suitable for use in hazardous atmospheres and wet locations.

WARRANTY

All ENDUREX fixtures carry an unconditional warranty against failure to meet standards of specific illuminated life.

SIGN SERIES USEFUL LIFE

END1

ENDUREX-1

SERIES

10

20

YEARS

15

YEARS

YEARS

OPTIONS AND ACCESSORIES

P1 12” Pendant Kit

# OF FACES

1

2

FACE COLOR HOUSING COLOR OPTIONS

R

RED

G

GREEN

B

BLACK

W

B

WHITE

BLACK

SEE

BELOW

P2

P3

P4

24” Pendant Kit

36” Pendant Kit

48” Pendant Kit

WG16113 Custom Fit Wire Guard

**END2 Models and accessories available until 1/1/2009**

AGENCY APPROVAL

ETL listed, per UL Standard 924 and Life

Safety Code NFPA 101 (1991). Meets requirements of National Electrical Code

Article 500, Class I and II conditions.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

DEFIANT

WET LOCATION EXIT SIGNS AND COMBINATION UNITS

The DEFIANT exit series is designed with the extremes of environment in mind. The fully gasketed polycarbonate lens and ABS thermoplastic housing allows the DEF Series to be installed in locations that require NEMA

4X protection. Optional weatherproof par36 emergency lighting heads can also be installed on this unit. The

DEF series is available configured with high-output LED’s in AC only and self-powered operation versions.

EXTERNAL SPECIFICATIONS

The DEF series housing is constructed from durable, corrosion resistant ABS thermoplastic. The housing is fully gasketed for wet location applications and is supplied standard in a gray finish. Four polycarbonate pressure screws firmly hold the polycarbonate lens in place. Wall, ceiling, or end mount configurations are available. Single or double face versions must be specified. Removable chevron arrows are standard on each unit. The self-powered version comes standard with an external LED status indicator and test switch.

INTERNAL SPECIFICATIONS

AC ONLY: standard 120/277 VAC input

SELF-POWERED: standard self-powered versions use sealed nickel-cadmium batteries to provide a minimum 90 minutes of emergency duration. Maintenance free sealed lead acid battery used when optional emergency heads are ordered. Optional 120 minute duration battery is available. Solid state charger and transfer.

EXTREME CLIMATE DESIGN

The DEF series has been designed to perform in applications where the climate would punish any standard sign. The entire internal cavity of the sign is protected from moisture invasion by an extremely resilient silicone gasket. The liquid gasketing is “hot-bonded” to the lens during the manufacturing process. This procedure eliminates any chance of the gasketing to become dry and pull away from the lens. The gasketing also holds its original form and has “memory retention” so that it effectively and consistently protects the DEF series from moisture. The DEF can also be equipped with an optional thermostatically controlled heater for cold environments. The ABS housing is highly corrosion resistant and will not rust or rot. The molded ABS finish cannot be scraped or scratched away exposing raw metals like standard steel signs.

BATTERY TECHNOLOGY

The DEF-SP-6-27, 6-36, and 6-54 are designed with an internal, maintenance free, valve regulated sealed lead-acid battery providing emergency lighting duration as per specified unit. The DEF-SP is designed with an internal maintenance free, sealed nickel-cadmium battery providing a minimum emergency duration of 90 minutes. An optional 120 minute nickel-cadmium battery is available.

Recharge time of the battery is 24 hours. The maximum battery operating temperature is 50º C.

MECHANICAL SPECIFICATIONS

The DEF series housing is constructed from durable, corrosion resistant ABS thermoplastic. The housing is fully gasketed for damp, wet, and NEMA 4X locations with a hot-bonded silicone gasket.

Exit face(s) are made from a high clarity, clear polycarbonate that has been painted white on the internal side only, making the unit highly scratch resistant. Field removable chevron arrows are standard on each face. Four polycarbonate screws firmly hold the face to the housing. Optional par36 heads are constructed of high-impact black thermoplastic that has been sealed against moisture infiltration.

CHARGER SPECIFICATIONS

The DEF series utilizes a solid state transfer technology that eliminates relay failure that can be cause by particle build up on the relay. All of the components used in the circuitry are temperature compensated. Status is easily determined via the LED display. A push button test switch allows maintenance personnel to quickly confirm the operational status of the exit on AC fail.

EXIT SIGN ONLY

SIGN SERIES OPERATION

DEF

DEFIANT SERIES

AC

SP

90 MINUTE

BACKUP

MOUNTING LED / # OF FACES

W

WALL (NO CANOPY)

R1

RED / SINGLE

R2

RED / DOUBLE

C

CEILING (INSTALLED)

G1

GREEN / SINGLE

E

END (INSTALLED)

G2

GREEN / DOUBLE

OPTIONS

2CKT

DUAL CIRCUIT

120SP

120 MIN. EMER.

BZ

BUZZER

SIGN SERIES

DEF

DEFIANT SERIES

MOUNTING LED / # OF FACES

W

WALL (NO CANOPY)

R1

RED / SINGLE

R2

RED / DOUBLE

C

CEILING (INSTALLED)

E

END (INSTALLED)

G1

GREEN / SINGLE

G2

GREEN / DOUBLE

HEADS

0

NO HEADS

1H

ONE HEAD

2H

TWO HEADS

EXIT SIGN COMBINATION

OPERATION

6-27

(6V 27W)

6-36

(6V 36W)

6-54

(6V 54W)

OPTIONS

2CKT

120SP

BZ

DUAL CIRCUIT

120 MIN. EMER.

BUZZER

LAMP SELECTION

Please see the EGRESSOR Series lamp options.

WARRANTY

The DEF Series comes from the factory with an unconditional 5 year product

Certified by ETL or CSA to UL924 Standards

NEMA 4X

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

VALUMINA

DIE-CAST VANDAL RESISTANT/WET LOCATION EXIT

The VALUMINA exit series is designed to stand up to high abuse areas such as correctional facilities, schools, apartment complexes and public areas. The VAL series utilizes a long-life neoprene gasket, die-cast aluminum housing and polycarbonate lens that provides maximum durability against vandalism and outdoor elements. An internal heater option with thermostat is available for low temperature installations.

EXTERNAL SPECIFICATIONS

The VAL series housing is constructed from .420” thick, heavy duty die-cast aluminum. The face plates are protected by high abuse clear polycarbonate, which is recessed into the housing. Tamper resistant screws are standard. The housing is fully gasketed for wet location applications and is supplied standard in a black finish. Wall, ceiling, end or universal mount configurations are available. Single or double face versions must be specified. Perforated chevron arrows are standard on each unit. The self-powered version comes standard with an external LED status indicator and test switch.

INTERNAL SPECIFICATIONS

AC ONLY: standard 120/277/347 VAC input

SELF-POWERED: standard self-powered versions use sealed Nickel-

Cadmium batteries to provide a minimum 90 minutes of emergency duration.

Optional 120 minute duration battery is available. Solid state charger, auto test and transfer are standard.

VANDAL RESISTANT DESIGN

The ultra heavy duty design and appearance of the VAL series warns potential vandals that this is no regular sign. The stencil is protected by a 1/8” thick, impact resistant polycarbonate shield that is recessed into the housing and fastened with 4 tamper resistant screws. The VALENCIA offers a contemporary look and durability like no other.

MECHANICAL SPECIFICATIONS

The VAL series housing is constructed from extra heavy duty cast aluminum with a 1/8” thick polycarbonate shield. Tamperproof screws and field adjustable chevron are standard. The polycarbonate face shield is recessed into the housing making the VALUMINA series one of the most rigid, yet attractive high abuse signs on the market.

AUTOTEST DIAGNOSTIC

The self-powered VALUMINA comes standard with a self diagnostic system. Featuring continuous monitoring of the units main components

(battery, charger, transformer, lamps, & LED’s) and providing instant visual verification of the status.

BATTERY TECHNOLOGY

The VAL-SP is designed with an internal, maintenance free, sealed Nickel-

Cadmium battery providing a minimum emergency duration of 90 minutes.

An optional 120 minute Nickel-Cadmium battery is available. Recharge time of the battery is 24 hours. The battery operating temperature range is

+32º F - +113º F without internal heater/thermostat option. The minimum operating temperature with internal heater/thermostat option is -40º F.

ELECTRICAL SPECIFICATIONS

The VALUMINA series is configured with high output LED lamps. LED is standard with 120/277 VAC input. All LED version consumes < 5 watts nominal power.

SIGN SERIES OPERATION

VAL

VALUMINA

SERIES

AC

SP

90 MINUTE

BACKUP

MOUNTING

W

WALL (no canopy)

C

CEILING

E

END

U

UNIVERSAL

LED / # OF FACES

R1

RED / SINGLE

R2

RED / DOUBLE

RU

RED / UNIVERSAL

G1

GREEN / SINGLE

G2

GREEN / DOUBLE

GU

GREEN / UNIVERSAL

HOUSING

WW

WHITE

BB

BLACK

OPTIONS

FL

FLASHER

BZ

BUZZER

HT

HEATER

IRT

INFARED REMOTE TEST

120SP

120 MIN. EMER.

WARRANTY

The VAL Series comes from the factory with an unconditional 5 year product warranty.

Certified by ETL or CSA to

UL924 Standards

IP 66

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

EE-1/EE-2

EMERGENCY LIGHT

Decorative and economical unit with “EZ” install back plate feature has modern appearance and low maintenance. It is ideal for commercial, institutional, and industrial facilities where economy, appearance, and ultimate ease on installation and maintenance are desired. Also ideal when a low profile unit needs to meet limited space requirements, and any space requiring back-up emergency lighting.

FEATURES

Completely self-contained

Fully automatic operation

Compact, low profile design in neutral finish

Universal mounting plate with “EZ” quick connect for

rapid labor saving installation

Push to test switch

6-volt premium grade, pure lead, calcium, maintenance-

free battery with 10-year expected life

Environmentally-coated, solid state charger

Automatic low voltage disconnect (LVD) protects battery

from deep discharge

Universal transformer for 120 or 277 VAC operation

Standard with two fully adjustable 5.4 watt, glare-free

lighting heads

Injection molded, V-O flame retardant, high impact,

thermoplastic housing

Charge rate/power on LED light indicator

OPERATION

Whenever normal utility power fails, the internal, solid-state transfer switch automatically connects the internal battery to the two lamp heads, illuminating them for a minimum of 90 minutes.

When utility power is restored, the battery is disconnected from the lamps. Recharging the battery is initiated by a fully automatic solid-state, two-rate charger, which includes current limiting and temperature compensation to assure that the optimum recharging rate, for even a fully discharged battery, will be accomplished within 12 hours.

WARRANTY

Both the EE-1 fixture and the internal battery carry a one year warranty form the time of shipment to be free from defective material and workmanship. The battery is pro-rated for a 10-year period when operated at normal ambient temperatures.

ORDERING INFORMATION

EE-1 - 6 volt 11 watt unit with two 5.4 watt lamps.

EE-2 - 6 volt 22 watt unit with two 5.4 watt lamps. Provides 11 additional watts of remote power.

*For black units, use suffix “B”

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

EE-3

EMERGENCY LIGHT

The ISI EE-3 is a compact, economical unit that is efficient and easy to install. Made of a polycarbonate housing, available in white or black finish, the EE-3 is completely self contained and fully automatic.

FEATURES

Completely self-contained

Fully automatic operation

Compact, low profile design in neutral finish

Universal mounting plate with “EZ” quick connect for

rapid labor saving installation

Push to test switch

6-volt premium grade, pure lead, calcium, maintenance-

free battery with 10-year expected life

Environmentally-coated, solid state charger

Automatic low voltage disconnect (LVD) protects battery

from deep discharge

Universal transformer for 120 or 277 VAC operation

Standard with two fully adjustable 5.4 watt, glare-free

lighting heads

Injection molded, V-O flame retardant, high impact,

thermoplastic housing

Charge rate/power on LED light indicator

Catalog Model # Emer. Operation

EE-3 90 minutes

EE-3-B (Black)

EE-3-CP (cord)

90 minutes

90 minutes

Ordering Information: EE-3

Voltage Input

120V/277

120V/277

120V/277

Lamp Wattage

2 x 5.4W

2 x 5.4W

2 x 5.4W

Battery Voltage

6 volts

6 volts

6 volts

Warranty

Yes

Yes

Yes

ALSO AVAILABLE IN BLACK.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

EXCEL-EMER

EMERGENCY LIGHT

Ideal for any location requiring emergency lighting. The EXC-EM Series combines the best of economical operation, a well engineered and attractive appearance, low maintenance and the ultimate in ease of installation. The EXC-EM Series can be installed in combination with EXCEL L.E.D. exit signs.

FEATURES

Rugged universal dual voltage transformer for both 120 and 277 volt applications.

Environmentally coated, solid state charging circuit features an automatic low voltage disconnect (LVD), lockout feature to protect against deep discharge and AC brown out.

Completely self contained & fully automatic operation.

6-volt premium grade, pure lead, calcium, maintenance free battery with

10 year expected life.

Charge rate and power on LED indicator light.

Easy push to test switch. (remote test option available)

Injection molded, V-O flame retardant, high impact, thermoplastic housing available in black or white.

Universal mounting plate featuring convenient knockouts for easy installation with compact low profile design.

OPERATION

When normal utility power fails, the internal solid state transfer switch automatically connects the battery to the lamp heads and provides a minimum of 90 minutes of light.

When utility power is restored, recharging of the battery is initiated by an automatic, solid state, two-rate charger, which includes current limiting and temperature compensation to assure that optimum recharge is achieved. A fully discharged battery will be fully recharged within 12 hours.

WARRANTY

The EXC-EM fixture and battery are warranted to be free from defects for a period of one year from date of purchase. The battery is covered by a 10 year pro-rated warranty.

UNIT SERIES WATTS LAMPS

EXC-EM

EXCEL SERIES

EMERGENCY LIGHT

11 18

27 32

X

5 Watt MR-16

Z

Y

10 Watt MR-16

12 Watt MR-16

**10Watt MR-16 Lamps are only available in 18, 27 & 32Watt units

**12Watt MR-16 Lamps are only available in 27 & 32Watt units.

**

**

OPTIONS AND ACCESSORIES

CP

DR

SD

Cord & Plug

Damp Rated

Self Diagnostics

HOUSING COLOR

W

WHITE

B

BLACK

OPTIONS

SEE BELOW

5.0”

WG Wire Guard

12.75”

5.5”

AGENCY APPROVAL

Meets the illumination requirement of NFPA Life Safety Code 101,

5-10.2.2. Certified and tested to U.L. 924. ETL listed.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

MINI-EGRESSOR

STEEL EMERGENCY LIGHT

The ISI MINI-EGRESSOR (M-EGR) offers both 6 volt and 12 volt systems that provide up to 54 lamp watts of emergency power. Series M-EGR offers state-of-the-art electronics, economy, and ease of installation as found in all ISI products. Lamps are factory installed, and our battery lockout circuit allows the battery to be connected even when AC power is not available. This eliminates returning to the job site to connect the battery. Series M-

EGR housings are gray, white, or black powder coated 20 gauge steel. Lamp heads are high impact flame retardant plastic.

FEATURES

12, 18, 27 watts (6 volt) in smaller housing (2.5” deep)

27, 36, 54 watts (12 volt) in 4.5” deep housing

Sealed maintenance free lead batteries.

Battery lockout circuit

LVD - low voltage disconnect.

Temperature compensation and brownout circuit.

High charge and AC ready LED.

Dual voltage transformer (120/277VAC)

Rugged 20-gauge Steel housing.

.

3 year warranty on unit and battery, 5 years additional pro rata on battery.

Short circuit resistance circuit.

M-EGR

MINI-EGRESSOR

SERIES

LAMPHEADS

2

WHITE

3

BLACK

4

GRAY

00

01

02

03

04

No Heads

6V, 5.4W H.I.T

6V, 7.2W H.I.T.

6V, 8W SBH

6V, 9W H.I.T

05

06

07

6V, 9W SB

6V, 12W SB

6V, 12W SBH

13

14

15

*** SB = SEALED BEAM

*** SBH = SEALED BEAM HALOGEN

08

09

10

11

12

OPTIONS

6

12

6V, 18W SB

6V, 25W SB

(METAL HEADS)

12V, 9W H.I.T.

12V, 8W SBH

12V, 12W SB

12V, 12W SBH

12V, 18W SB

12V, 25W SB

(METAL HEADS)

12 18

27 36

54

SEE

BELOW

SEE

BELOW

VM Voltmeter

AM Ammeter

*For more available options, please contact factory.

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

EGRESSOR

STEEL EMERGENCY LIGHT

The ISI EGRESSOR (EGR) is recommended for 12 volt, 72 watt or 100 watt systems. Series EGR offers state-of-theart electronics, economy, and ease of installation as found in all ISI products. The lamps are factory installed, and our battery lockout circuit allows the battery to be connected even when AC power is not available. Series EGR housings are gray, white, or black powder coated 20 gauge steel. Lamp heads are high impact flame retardant plastic.

FEATURES

6 volt and 12 volt system.

27, 36, 54, 72, and 100 watts (6 volt).

27, 36, 54, 72, and 100 watts (12 volt).

Sealed maintenance free lead batteries.

Battery lockout circuit

LVD - low voltage disconnect.

Temperature compensation and brownout circuit.

High charge and AC ready LED.

Dual voltage transformer (120/277VAC)

Rugged 20-gauge steel housing.

3 year warranty on unit and battery, 5 years additional

pro rata on battery.

Short circuit resistance circuit.

EGR

EGRESSOR SERIES

LAMPHEADS

00

01

02

03

04

No Heads

6V, 5.4W H.I.T

6V, 7.2W H.I.T.

6V, 8W SBH

6V, 9W H.I.T

05

06

07

6V, 9W SB

6V, 12W SB

6V, 12W SBH

13

14

15

*** SB = SEALED BEAM

*** SBH = SEALED BEAM HALOGEN

08

09

10

11

12

OPTIONS

2

WHITE

3

BLACK

4

GRAY

6

12

6V, 18W SB

6V, 25W SB

(METAL HEADS)

12V, 9W H.I.T.

12V, 8W SBH

12V, 12W SB

12V, 12W SBH

12V, 18W SB

12V, 25W SB

(METAL HEADS)

27 36

54 72

100 125

SEE

BELOW

SEE

BELOW

VM Voltmeter

AM Ammeter

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

*For more available options, please contact factory.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

EGRESSOR-PLUS

STEEL EMERGENCY LIGHT

Rugged construction for the most demanding industrial applications. The ISI EGRESSOR-PLUS (EGR-P) series offers 150, 200, 250, 300 and 400 lamp watts of emergency power in 12 or 24 volts. The EGR-P series has been designed with state of the art electronics including our battery lockout circuit, which allows the battery to be connected to the circuit even when AC power is not available. Lamp heads are factory installed on the unit as just another example of ISI’s ease on installation.

FEATURES

Sealed maintenance free lead batteries.

Battery lockout circuit.

LVD - low voltage disconnect.

Choice of lamp heads.

Temperature compensation and brownout circuit.

High charge and AC ready LED.

Dual voltage transformer (120/277VAC)

Rugged 20-gauge steel housing.

Units in white, black, or industrial gray powder finished

coating.

3 year warranty on unit and battery, 5 years additional

pro rata on battery.

Short circuit resistance circuit.

EGR-P

EGRESSOR PLUS

SERIES

2

WHITE

3

BLACK

4

GRAY

LAMPHEADS

00

01

02

03

No Heads

6V, 5.4W H.I.T

6V, 7.2W H.I.T.

6V, 8W SBH

08

09

10

11

04

05

06

07

6V, 9W H.I.T

6V, 9W SB

6V, 12W SB

6V, 12W SBH

12

13

14

15

*** SB = SEALED BEAM

*** SBH = SEALED BEAM HALOGEN

OPTIONS

12

24

6V, 18W SB

6V, 25W SB

(METAL HEADS)

12V, 9W H.I.T.

12V, 8W SBH

12V, 12W SB

12V, 12W SBH

12V, 18W SB

12V, 25W SB

(METAL HEADS)

125 150

200 300

400

SEE

BELOW

SEE

BLEOW

Consult factory for dimensions for your application.

VM Voltmeter

AM Ammeter

*For more available options, please contact factory.

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

RECESSED -EGRESSOR

STEEL EMERGENCY LIGHT

The RECESSED-EGRESSOR (R-EGR) offers emergency lighting in applications where wall mounted units are inappropriate. The R-EGR utilizes the existing suspended (T-bar) grid ceilings. This series offers a wide range of wattages in both 6 volt and 12 volts. With 50 lamp wattage and voltage variations, R-EGR can cover all your commercial emergency lighting needs.

FEATURES

Sealed maintenance free lead batteries.

Battery lockout circuit.

LVD - low voltage disconnect.

Choice of lamp heads.

High charge and AC ready LED.

Dual voltage transformer (120/277VAC)

Rugged 20-gauge steel housing.

Short circuit resistance.

Brownout protection.

Warranted to be free from defects for 3 years.

Batteries are prorated for 5 years.

R-EGR

RECESSED EGRESSOR

SERIES

2

WHITE

3

BLACK

4

GRAY

LAMPHEADS

00

01

02

03

No Heads

6V, 5.4W H.I.T

6V, 7.2W H.I.T.

6V, 8W SBH

08

09

10

11

04

05

6V, 9W H.I.T

6V, 9W SB

12

13

06

07

HEADS)

6V, 12W SB

6V, 12W SBH

*** SB = SEALED BEAM

14

15

*** SBH = SEALED BEAM HALOGEN

OPTIONS

6

12

6V, 18W SB

6V, 25W SB

(METAL HEADS)

12V, 9W H.I.T.

12V, 8W SBH

12V, 12W SB

12V, 12W SBH

12V, 18W SB

12V, 25W SB

(METAL

27 36

54 72

100 125

SEE

BELOW

SEE BELOW

VM Voltmeter

AM Ammeter

*For more available options, please contact factory.

AGENCY APPROVAL

Meets the illumination requirement of

NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to UL924. ETL listed.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

DEFIANT

NEMA 4X RATED CARLON PVC EMERGENCY LIGHT

The DEFIANT (DEF) series of industrial emergency lighting units are designed to be durable, dependable, and easy to install. The fully gasketed NEMA 4X rated Carlon PVC housing can be used in most damp, wet, and hose down areas. The DEF has been designed with the PulseGuard pulse switching charger. The PulseGuard offers superior performance & energy efficiency versus conventional constant voltage chargers. Traditional top mounted par 36 style heads are standard.

EXTERNAL SPECIFICATIONS

The DEF series is constructed with a durable NEMA 4X rated Carlon PVC cabinet. Industrial gray finish is standard. Emergency lighting heads are molded from high impact thermoplastic in a matching color; par36 heads are standard. Integrated mounting feet ensure proper and secure installation. The front access panel is hinged to allow for trouble free installation and maintenance. External test switch and monitor LED are standard.

LAMP HEAD FEATURES

The DEF series is normally supplied with two top mounted par36 style 9W heads. Lamp head styles are constructed of high impact thermoplastic in a color matching the finish of the cabinet (industrial gray is standard). Please note: par36 style food-prep approved lenses are also available when ordering.

BATTERY TECHNOLOGY

The DEF series is designed with a maintenance free, sealed valve regulated lead acid battery that provides a minimum emergency duration of 90 minutes (for the listed rating). Recharge time of the battery is 24 hours. The maximum battery operating temperature is 50º C.

MECHANICAL SPECIFICATIONS

The DEF is constructed from a durable, fully gasketed NEMA 4X rated Carlon PVC housing. The front access panel is hinged for trouble-free installation and maintenance. Four integrated mounting feet ensure proper, secure, and accurate wall or ceiling installation onto most surfaces. The DEF is supplied standard in an industrial gray Carlon PVC finish. External test switch and monitor LED standard.

CHARGER SPECIFICATIONS

The DEF series utilizes a pulse switching charger that is up to 70% more efficient than older constant voltage chargers. The charger is a fully automatic current limited charger with solid state line-latched low voltage disconnect protection. All components used in the circuitry are temperature compensated.

The charger also has brownout and short circuit protection. Charger status is easily determined via a dual diagnostic LED display which indicates AC/ON and High Charge. An external push button test switch allows maintenance personnel to quickly determine the operational status of the unit and lamp load.

LAMP SELECTION

00 No Heads

01

02

03

04

05

06

07

6V, 5.4W H.I.T

6V, 7.2W H.I.T.

6V, 8W SBH

6V, 9W H.I.T

6V, 9W SB

6V, 12W SB

6V, 12W SBH

08

09

10

11

12

13

14

15

6V, 18W SB

6V, 25W SB

(METAL HEADS)

12V, 9W H.I.T.

12V, 8W SBH

12V, 12W SB

12V, 12W SBH

12V, 18W SB

12V, 25W SB

(METAL HEADS)

WATTAGE A B C D

27W - 36W 6.2” 8” 10” 5”

54W - 72W 6.2” 10” 12” 7”

100W - 125W 6.2” 12” 14” 7”

SIGN SERIES

DEF

DEFIANT

SERIES

OPERATION

6

12

(volt DC)

(volt DC)

CAPACITY

27

(6 volt only)

36 54

72 100

1H

2H

HEADS

ONE HEAD

TWO HEADS

LAMP TYPE

SEE ABOVE

EX: DEF-6-54-2H-07-VM

DESC: Defiant Series, 6 volt, 54 watt, two lamp heads, 6V, 12W sealed beam halogen bulbs, Voltmeter

OPTIONS

SD

SELF DIAGNOSTICS

VM

VOLTMETER

AM

AMMETER

TD

TIME DELAY (SPECIFY)

FP

FOOD PREP LENS

WARRANTY

The DEF Series comes from the factory with an unconditional 5 year product warranty.

Certified by ETL or CSA to UL924 Standards

NEMA 4X

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

ELLIPTICA

ARCHITECTURAL OUTDOOR EMERGENCY

The ELLIPTICA (EL) Series Emergency Light provides an attractive solution to applications that require low profile egress emergency lighting with rugged durability and good looks. Constructed of die-cast aluminum with a polycarbonate refractor and finished epoxy powder coat, the ELLIPTICA is gasket sealed and ready for use in both indoor and outdoor applications.

FEATURES

Wet location listed for indoor or outdoor applications 32° - 122° F

Optional Cold temperature package for -4° - 122° F applications

Rugged die-cast aluminum construction

Durable powder coat finish available in Bronze, White, Black and

Brushed Aluminum

Snap fit assembly with vandal resistant latch clips; no visible hardware

Gasket sealed to suit universal junction boxes

Conduit entry provided on top of unit

Available as a 6 volt DC remote fixture

UV stabilized polycarbonate refractor resists yellowing and provides uniform distribution

Two 6 watt high output Xenon lamps for superior illumination

Optional decorative colored night light

Integral push-to-test switch

ELECTRONICS

Self Test / Self Diagnostic circuit is provided as standard thereby

• reducing manual testing obligations

Easily visible Bi-Color LED diagnostic indicator

Automated, 28 day, self test checks lamp, battery and electronic circuitry over a short one minute test. Extended 30 minute emergency duration tests are automatically conducted every six months

Premium long life high temperature rated Nickel Cadmium battery

Sealed externally accessible test switch for manual momentary test operation

Field selectable 120 or 277 VAC input

Brownout sensing assures emergency illumination during periods of low line voltage

Self-compensating solid state Constant Current Charger provides extended float life and rapid recharge

Zero current LVCO ensures positive charge acceptance following an extended discharge

Listed UL 924 Damp and Wet locations

SIGN SERIES HOUSING

EL6

SELF-POWERED

ELR

6 VOLT DC

12 WATT

REMOTE

(2-6 watt lamps)

B

BLACK

W

WHITE

BRZ

BRONZE

BAL

BRUSHED

ALUMINUM

NIGHT LIGHT

NLW

WHITE LED

NLG

GREEN LED

NLA

AMBER LED

NLB

BLUE LED

OPTIONS

CT

COLD TEMP

OPERATION

(-4° F)

WARRANTY

The Elliptica comes from the factory with a three year limited warranty.

AGENCY APPROVAL

ETL listed, per UL Standard 924 and Life Safety Code NFPA 101 (1991). Meets requirements of National Electrical Code

Article 500, Class I and II conditions.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

GIMBAL

EMERGENCY LIGHT

The RECESSED-GIMBAL (R-GIM) is designed to be installed within the sheetrock or drop ceiling and blends inconspicuously with other existing recessed lighting fixtures. The GIMBAL mounted lamp permits directional lighting and is adjustable to 45 degrees on two planes. Standard finish is white. Available as complete emergency unit, or as a remote.

FEATURES

6 volt, 8 watt halogen lamp standard.

U.L. approved for use in insulated ceilings.

Steel housing.

Electronics and battery are mounted in a removable bracket.

Sealed maintenance free lead battery.

Solid state charging circuit.

120/277 VAC Input, 60 Hz, 8W.

24 hour recharge after 90 min. discharge.

Automatic brown out protection.

Low voltage disconnect (LVD) protects battery from deep discharge.

Short circuit and overload protection on DC output circuit.

R-GIM

RECESSED GIMBAL

2

WHITE

WATTAGE OPTIONS

03

04

05

Lamp Options

01

02

6V, 5.4W H.I.T 06

6V, 7.2W H.I.T 07

6V, 8W SBH

6V, 9W H.I.T

6V, 9W SB

6V, 12W SB

6V, 12W SBH

8.75” diam.

4”

7”

6.75”

8.625”

Warranty

The fixture is warranted to be free from defects for 2 years. The battery has a

5 year, prorated warranty.

Agency Approval

Meets the illumination requirement of NFPA Life Safety Code 101, 5-10.2.2.

Certified and tested to standard UL924. UL listed and meets NEC and OSHA codes.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

I

S

I

REMOTE LAMPHEADS

ISI offers a full assortment of both plastic, metal and NEMA 4X rated remote lamp heads. They are available in both white and black, 6 volt and 12 volt. All remote lamp head assemblies are available for outdoor use with a weatherproof option.

ORDERING GUIDE:

MODEL NUMBER DESCRIPTION

EXC-RPL-6-X

EXC-2RPL-6-X

EXC-RPL-6-X-WP

EXC-2RPL-6-X-WP

Excel head, 6 volt, 5 watt MR-16 Lamp w/ mounting plate

2H Excel, 6 volt, 5 watt MR-16 Lamps w/ mounting plate

Excel head, 6 volt, 5 watt MR-16, w/ mtg. plate, weatherproof

2H Excel, 6 volt, 5 watt MR-16, w/ mtg. plate, weatherproof

RPL-6-7.2-18

RPL-6-7.2-36

RPL-6-8-SB

RPL-6-8-SBH

RPL-6-9

(HIT-Par36)

RPL-6-12-SB

RPL-6-12-SBH

RPL-6-18-SB

RPL-12-9

(HIT-Par36)

RPL-12-12-SB

RPL-12-12-SBH

RPL-12-18

(HIT-Par36)

RPL-12-18-SB

Plastic, 6 volt, 7.2 watt, high intensity tungsten (PAR 18)

Plastic, 6 volt, 7.2 watt, high intensity tungsten (PAR 36)

Plastic, 6 volt, 8 watt, sealed beam

Plastic, 6 volt, 8 watt, sealed beam halogen

Plastic, 6 volt, 9 watt, high intensity tungsten

Plastic, 6 volt, 12 watt, sealed beam

Plastic, 6 volt, 12 watt, sealed beam halogen

Plastic, 6 volt, 18 watt, sealed beam

Plastic, 12 volt, 9 watt, high intensity tungsten

Plastic, 12 volt, 12 watt, sealed beam

Plastic, 12 volt, 12 watt, sealed beam halogen

Plastic, 12 volt, 18 watt, sealed beam

Plastic, 12 volt, 18 watt, sealed beam halogen

REMOTE METAL LAMPHEADS

ORDERING GUIDE:

MODEL NUMBER DESCRIPTION

RML-6-8-SB/SBH

RML-6-9

RML-6-12-SB/SBH

RML-12-9

RML-12-12-SB/SBH

Metal, 6 volt, 8 watt, sealed beam or sealed beam halogen

Metal, 6 volt, 9 watt, high intensity tungsten

Metal, 6 volt, 12 watt, sealed beam or sealed beam halogen

Metal, 12 volt, 9 watt, high intensity tungsten

Metal, 12 volt, 12 watt, sealed beam or sealed beam halogen

NEMA 4X REMOTE PLASTIC LAMPHEADS

ORDERING GUIDE:

MODEL NUMBER

NRPL-6-9

NRPL-12-9

DESCRIPTION

Plastic, NEMA 4X rated, 6 volt, 9 watt, high intensity tungsten

Plastic, NEMA 4X rated, 12 volt, 9 watt, H.I.T

** For two and three remote heads per unit add prefix “2” or “3” to part number.

OPTIONS

B Black

WP Weatherproof

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

I

S

I

WIRE GUARDS AND WET LOCATION BUBBLES

ISI offers several different dimensions of wire guards to protect exit signs or emergency lights from balls and vandalism. ISI also offers wet location domes to protect against moisture and weather related atmospheres.

WG14.5610.5 14.5 6 10.5

WG1410.7514 14 10.75 14

WG13.51216.5 13.5 12 16.5

***Custom wire guards are available for special applications. Consult factory.

The domes are for use with L.E.D. signs including the Excel, Stark, and Mitigator Series.

Each dome comes with a rubber gasket to fit between the dome and the wall, therefore completely sealing all moisture from inside the dome.

WLBUB-E-W Wet location dome for Excel-EM unit.

WLBUB-C-W Wet location dome for Excel-2 unit.

WLBUB-S-W

Excel, Mitigator & Stark Series exits.

WLBUB-EM

Mon-Emer, EE-1/2 & 3 emergency

units.

WLBUB-EX Wet location dome for Monarch exits.

WLBUB-COM Mon-Combo and Navigator exits.

NOTE:

Additional domes available by special order.

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

FB Series

FLUORESCENT BALLAST

Fluorescent emergency ballasts are designed to operate most single or bi-pin tubular lamps, as well as 2-pin or 4-pin compact fluorescent lamps including U-shaped, HO, VHO, circuline, energy saving, twin-tube, double twin-tube

(quad), triple twin-tube, long compact, and 2D lamps. They are compatible with most 1-, 2-, 3-, and 4-lamp electronic, standard energy saving and dimming AC ballasts, as well as with energy management systems such as occupancy detectors and photo sensors. Products are available for indoor/dry, damp and hazardous location fixtures, and may be modified to accommodate special voltages, line frequencies and longer runtimes.

Long life, high temperature Ni-Cad battery

Long life L.E.D. charge light

Dual voltage 120/277V, 60 Hz

Vandal Resistant

Test switch provided

Painted steel case

Meets or exceeds all national electrical code and life safety code emergency lighting requirements

Damp location rated

TMK-80

EMERGENCY BATTERY PACK

For use when the unit is mounted on top of fixture. The TMK-80 covers the wiring that goes from the battery pack into the fixture.

TBMK-DL/1-160

EMERGENCY BATTERY PACK OPTION

For use when the battery pack cannot be mounted on the light fixture. The battery pack is mounted in the TBMK, then mounted on the ceiling grid.

RTK

REMOTE TEST KIT

The remote test kit allows for remote mounting of the test switch and indicator light. The kit consist of a 3” section of flex, junction box, and cover.

MODEL

LAMP COMPATIBILITY CHART

FB-CP FB-0 FB-1 FB-2 FB-3

1400 3000

Number of Lamps Supported Linear Lamps

2’-4’ Rapid, Instant, or

Energy Savings, T8-T12

2’-8’ Rapid, Instant, or

Energy Savings, T8-T12,

HO, VHO

2’-8’ Rapid, Instant, or

Energy Savings, T8-T12,

HO, VHO

20W - 40W Circline

20W - 40W Circline

1 1 1 1

1 1

2

1

2

1

2

EMERGENCY BALLAST LINEAR FLUORESCENT

FB-0 Operates one 2’-4’ T8-T12 lamp

FB-1 Operates one 2’-4’ T8-T12 lamp

Operates one/two 2’-4’ T8-T12 lamps, HO or

FB-2

VHO fluorescent lamps

Operates one 2’-8’ T8-T12 lamp, HO or VHO fluorescent lamps, parallel operation fluorescent

Compact Lamps

13, 18, 26(4-pin)

13W - 42W Twin, Quad or Triple (4-pin)

40W Biax

50W Biax

50W Biax

1

Number of Lamps Supported

1 1

1 1 1 1 1

1

40W 2

1

1

1

1

1

1

1

1

1

1

Other Lamp Types May Operate With These Ballasts.

Please Contact Factory For Compatibility

FB-3 Full lumen output, operates one 2’-8’, or two 2’-

4’ T8-T12 lamps

FB-CP1 Operates 2 Pin Lamps in recessed applications

FB-CP2 Operates 4 Pin Lamps in recessed applications

329 Otter Street, Bristol, PA 19007 • Tele: (215) 788-8870 • Fax: (215) 788-8873

I

S

I

August 08

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement