PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT 37°/0° CONTROL SETTING

Type A with Run/Start Capacitor 65°F (18°C) Ambient 90°F (32°C) Ambient

Operating Time 74 to 84% 100%

Freezer Temperature

Refrigerator Temperature

-5° to 2° F (-20° to -17° C)

34° to 39° F (1° to 4° C)

-1° to 3° F (-18° to -16° C)

34° to 39° F (1° to 4° C)

Low Side Pressure (cut-in)

Low Side Pressure (cut-out)

High Side Pressure (last 1/3 cycle)

Wattage (last 1/3 cycle)

Amps (running)

5 to 12 psig (34 to 83 kPa)

-2 to 2 psig ( -14 to 14 kPa)

85 to 95 psig (586 to 655 kPa)

45 to 55

.6 to 1.1

N/A

-2 to 2 psig (-14 to 14 kPa)

120 to 135 psig (827 to 931 kPa)

60 to 70

.7 to .9

Base Voltage

Cabinet Size

115 vac (127 vac max) deFrOst speciFicatiOns

Cut-in thermostat

Cut-out Watts

26’ & 28’ SD, 23’ CD 25° F (-4° C) 47° F (8° C) 500

Electronic Timer - (ADC) Defrost 24 minutes every 6-96 hours of compressor run time.

Electrical

Thermostat

Heater Voltage

Watts

3.1

heater cOndenser Fan MOtOr rpM

1100 CW Opposite Shaft ice MaKer speciFicatiOns

115 vac (127 vac max)

Opens at 48° F ( 9° C), Closes at 15° F ( -9° C) amps

0.03 Running

Ohms

31

Wire number

1

2

3

4

85 vac ice MaKer cOnnectOr pLUG cOnnectiOns

Wire color

Green/Yellow

Yellow

Black

Light Blue connects to:

Ground

Water Valve

Line

Neutral ice Maker errors displayed on “Ui” errOr ice ice ice ice

service data sheet

240389643

ice & Water - aUtOMatic deFrOst

BOttOM FreeZer - r134a

er IM/RAM Error (on POR only)Detection – on POR only. This error is detected as “no com/data link with

IM” by ERF 2500++ system controller (PB).

ip Invalid Protocol (this error is detected when the version of I/M pcb does not match version of 2500++ system controller)

ce IM Com Lost only after POR(no communication between the I/M pcb and the 2500++ system controller.) t3 TH3 Error (open or short) This error is detected when the thermister has failed on the suction line of the I/M.

system error codes displayed on “Ui” errOr test

Op or 2 sh or 3

Op or 2 sh or 3 sy sy sy

Freezer Sensor OPEN

Freezer Sensor SHORTED

FF Sensor OPEN

FF Sensor SHORTED eF Evaporator Fan Circuit ce Communication error cF Communication error dF In Manual Defrost

To initiate manual defrost press and hold, for 5 sec. FF(+) and FF(-), (d) and (f) will be displayed.

9

10

11

41

3

8

1

2

12

38

15 test

48c

49c

50c

51c

52c

54C

56c

55c diagnostic Mode note: see service Manual for complete description.

Activate: Hold FF (+) and FZ (+) for 5 sec.

Freezer Recover Mode, “1” ok

“Fr” Recovery mode, Icemaker in

“off” state. (See Note)

EEV On=Open Off=Closed , EEV must be in the open state for sealed system evacuation.

Com Link “1” ok “ER” error

57c

58c

59c

Fan test, on or off

Ice level sensor switch test

Fill limit switch test

(See Note)

TH1 Status “1” ok “ER” Replace 60c

TH3 Status “1” ok “ER” Replace

Mold heater test, on or off

Finger evap heater, on or off

Water valve test (See Note) de-activate: hold FF (+) for 5 sec.

61c

62c

63c

64c

Freeze limit switch test

(See Note)

IM evap heater test

EEV test

Harvest motor system test

(See Note)

Software version diagnostic Mode activate: FZ (+) and FZ (-) for

5 sec.

Standard compressor

Defrost heater

FF lighting

Water valve,water disp.

FZ lighting

Auger motor

Cube/crush solenoid

Perfect Temp Drawer

VCC Condensor fan

VCC Compressor

Evaporator fan de-activate: hold FF (+) for 5 sec.

note: see service Manual for complete description.

28

36

29

30

22

23

24

26

33

0-

Damper

Fresh food door

Freezer door

Defrost limit switch

Dispenser paddle

Ice door

FF Thermistor

FZ Thermistor

Ambient Thermistor

Software version

iMpOrtant saFety nOte

The information provided herein is designed to assist qualified repair personnel only.

Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance.

iMpOrtant

If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured.

caUtiOn

all electrical parts and wiring must be shielded from torch flame. dO nOt allow torch to touch insulation; it will char at 200°F and flash ignite (burn) at 500°F. excessive heat will distort the plastic liner.

nOte

This product comes equipped with an Adaptive Defrost Control (ADC). To activate manual defrost, simultaneously press and hold the Fresh Food up (+) and Fresh Food down (-) keys for 5 seconds. A “d” in the freezer temperature window and “F” in the refrigerator temperature window will display when the heater is activated. To deactivate manual defrost, simultaneously press and hold the Fresh Food up (+) and Fresh Food down (-) keys for 5 seconds. A “d” and “F” will be displayed until the defrost cycle is complete.

iMpOrtant

pLease retUrn this sheet tO it’s OriGinaL LOcatiOn.

FREEZER iCE MAKER iNFORMATiON

Test Cycling:

Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle.

Water Fill

Adjustment

Motor

Gear

Water Fill Volume:

The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked.

LINE POWER

ICE MAKER

P-3

P-1

Mounting

Plate

Screw

BLK BRN

THERMAL

CUT-OUT

GRN / YEL

MOLD MOUNTING

PLATE

MOTOR

RED

RED

MOLD HEATER

165 WATTS

HOLD

SWITCH

NO

C

BLK

NC

YEL

THERMOSTAT

NO

NO

C

NC

WATER FILL

SWITCH

BLU

C

NC

SHUT-OFF

SWITCH

LT. BLU

ICE MAKER

TUR

N Mounting

Plate

Screws

Timing

Gear

NEUTRAL

P-4

P-2

FF Ice Maker

(2419801)

242058901 Wiring Diagram

Frig FDBF 2500++ V4 with Dispenser