3/8" VARIABLE SPEED REVERSIBLE DRILL

3/8" VARIABLE SPEED REVERSIBLE DRILL
45137
SAFETY INSTRUCTIONS
• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
3/8" VARIABLE SPEED
REVERSIBLE DRILL
• Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
• Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have
the switch on invites accidents.
• Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in
moving parts.
• Only use safety equipment that has been approved by an appropriate standards
agency. Unapproved safety equipment may not provide adequate protection. Eye
protection must be ANSI-approved and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with grounded power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
• Avoid body contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is grounded.
MANUAL & SAFETY INSTRUCTIONS
-1-
• Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
ASSEMBLY DIAGRAM
23
24
25
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor
1
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
2
3
4
RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS* (120/240 VOLT)
EXTENSION CORD
NAMEPLATE
LENGTH
AMPERES
(at full load)
25’ 50’ 75’ 100’ 150’
0 – 2.0
18
18
18
18
16
2.1 – 3.4
18
18
18
16
14
3.5 – 5.0
18
18
16
14
12
5.1 – 7.0
18
16
14
12
12
7.1 – 12.0
18
14
12
10
-
12.1 – 16.0
14
12
10
-
-
16.1 – 20.0
12
10
-
-
-
TABLE A
27
5
6
7
8
9
10
26
11
12
13
14
15
16
17
18
21
20
* Based on limiting the line voltage drop to five volts at 150% of
the rated amperes.
22
19
PARTS LIST
OPERATION
1. Pressure: When drilling, never push hard on the drill bit to speed up drilling, the
Part No. DESCRIPTION
Part No. DESCRIPTION
1
Mounting Screw
15
Bearing
2
Spring Washer
16
Stator
2. Use of large diameter: The large the diameter of the chuck is the stronger counter
3
Chuck
17
Left Motor Housing
force effected on the hands. So should pay attention for not to loose the control of
4
Spindle
18
Cable Sheath
5
Half Circle Key
19
Plug
6
Bearing (201)
20
Clip
7
Fender Ring
21
Self Tapping Screw
8
Gear
22
Key
chuck will be damaged and lowered down the working efficiency.
the drill due to over stronger counter force. In order to have good control, you should
stand still and hold tightly on the drill with both hands. And always position the chuck
with the drilling surface vertically.
3. While drilling through a hole, sudden move of the drill could damage the chuck or drill
body, keep guard to release pushing force at anytime.
4. Switch: Select the right switch. Press power switch and locking switch, the drill will be
on continuous state and carry on continuous operation. To switch off, press power
switch once again to release the locking.
-2-
9
Fender Ring
23
Screw
10
Brass Bushing
24
Screw
11
Bearing
25
Blister
12
Rotor
26
Right Motor Housing
13
Carbon Brush Holder
27
Switch
14
Carbon Brush
-3-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising