Installing the remote control
batteries
1
3
Remove the battery cover from the back of the remote
control.
Squeeze tab ||
and lift cover.
|
Install two “AAA” size batteries, making sure to match
the + and — signs on the batteries to the signs on the
battery compartment.
Reinsert the battery cover in the remote control until the
tab snaps.
Caution: Batteries must not be exposed to excessive heat
such as sunshine, fire or the like.
Note:
Be sure to use AAA size batteries.
Dispose of batteries in a designated disposal area.
Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
When necessary to replace batteries in the remote control,
always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
Always remove batteries from the remote control if they
are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from
leaking into the battery compartment.
Remote control effective range
For optimum performance, aim the remote control directly
at the TV and make sure there is no obstruction between the
remote control and the TV.
Point remote control
toward remote sensor
on front of TV.
19
Learning about the remote control
The buttons used for operating the TV only are described
here.
WN) —
у — =
8
12 9
13 10
11
17
15
25 21
26 22
27 23
28 24
Note: The error message “NOT AVAILABLE” may appear if
you press a key for a function that is not available. —
1 POWER turns the TV on and off. When the TV is on, the
green LED indicator on the TV front will be illuminated.
2 PIC SIZE cycles through the picture sizes: Natural,
TheaterWide 1/2/3, Full, 4:3 HD, Native and Dot by Dot
(i= page 32).
3 PIC MODE selects the picture mode (v= page 35).
INPUT selects the video input source (r= page 28).
20
SLEEP accesses the sleep timer (is page 43).
FREEZE freezes the picture. Press again to restore the
moving picture (i page 34).
7 Channel Numbers (0-9, —/100) directly tune
channels. The button is used to tune digital channels
(i> page 31) or to edit the Favorites List (ss page 29).
8 FAV BROWSER accesses the Favorites List in the
Channel Brower™ (1° page 29).
9 RECALL displays TV status information (i= page 45).
10 CH AV cycles through programmed channels when no
menu is on-screen (1° page 24).
11 C.CAPTION accesses the closed caption (1° page 37).
12 MUTE reduces or turns off the sound (z= page 37).
13 VOL + — adjusts the volume level.
14 INFO displays TV status information as well as program
details, when available (i= page 45).
15 EXIT closes on-screen menus.
16 ENTER activates highlighted items in the main menu
system.
17 CH RTN returns to the last viewed channel or source
(15 page 32).
18 Arrow buttons (4 Y <>) When a menu is on-screen,
these buttons select or adjust programming menus. (Also
see </ >.)
19 <P While watching TV, these buttons open the
Channel BrowserTM and tune to the previous/next channel
in the channel history (re- page 30). (Also see “Arrow
buttons”)
20 MENU accesses the main TV menu system (1 pages 21
and 22).
21 STOP Stops the tape or DVD.
22 PLAY Begins playback of a tape or DVD.
23 SKIP wi Skips forward to locate later DVD chapters.
24 FF Fast-forwards the tape or DVD.(Press during play
mode to view the picture moving rapidly forward.)
25 EJECT Eject the tape or DVD.
26 PAUSE Press during play or record mode to pause the
picture ; press again to restart.
27 SKIP rea Skips back to beginning of current DVD
chapter, or locates previous chapters.
28 REW Rewinds/reverses the tpae or DVD. (Press during
play mode to view the picture moving rapidly backward.)
Using REGZA-LINK®
This is a new feature that uses CEC technology and allows
you to control Toshiba REGZA-LINK compatible devices
from the TV remote via HDMI connection (r# page 15).
When the Enable REGZA-LINK in the REGZA-LINK setup
menu (i= page 45) is set to On, the following REGZA-LINK
functions will be enabled.
REGZA-LINK® playback device (DVD player,
etc.) control
With your TV’s remote control, or using the REGZA-LINK
Player Control menu, you can control the connected REGZA-
LINK playback device you are watching.
Available remote control key functions:
Before using the following key functions, first set the MODE
SELECT switch on the remote control to TV.
Begins playback.
mn Stops playback.
A Pauses the picture during play or record mode.
e Skips forward.
Ces) Skips backward.
E Fast-forwards.
oo Rewinds/reverses.
АУ «<» Navigate contents menu, etc.
Em) Enters contents menu, etc.
EXIT
Returns to the previous menu.
Note: These functions depend on the devices connected.
REGZA-LINK® Player Control menu functions:
1 Press" and open the Preferences menu.
2 Highlight REGZA-LINK Player Control and press 6).
CC Selector
Base CC Mode
Channel
Menu
3 Press A or V to select the item you want to control and
press Em,
44
Power
Top Menu Accesses the top menu of a DVD.
Menu Accesses the menu of a DVD.
Contents Accesses the contents list when you press
19). At this time, the REGZA-LINK Player Control
Menu 41 A:
menu will disappear.
Note:
+ These functions depend on the devices that are connected.
* The REGZA-LINK Player Control item will be grayed out in
the following conditions:
— A non-HDMI input is currently selected.
— The Enable REGZA-LINK ¡tem is set to Off.
— The connected CEC device is not a playback or
recording device.
REGZA-LINK® input source selection
If a REGZA-LINK device with HDMI switching capability
(e.g. Audio Receiver) is connected to the HDMI input, you
can select another REGZA-LINK device that is connected to
the master HDMI device using the TV’s INPUT button. See
page 28 for details.
VOLUME and MUTE controls of Audio
Receiver
With your TV’s remote control, you can adjust or mute the
sound volume of the Audio Receiver. First, set the MODE
SELECT switch on the remote control to TV.
* (+) 9 adjust the volume level.
e "E turns off the sound.
Note:
e Jo use this function:
— Set Speaker Preference to Audio Receiver in the
REGZA-LINK Setup menu.
— Confirm that a connected REGZA-LINK device (such as
DVD player, etc) is selected for the Audio Receiver input
source.
* You can also use this function when the audio receiver is
connected to the TV's DIGITAL AUDIO OUT terminal (not
HDMI connection). In this case, select a digital audio input
mode on the Audio Receiver.
e These functions depend on the device connected.
Other REGZA-LINK® functions
When the Enable REGZA-LINK and each item in the
REGZA-LINK Setup menu are set to On, the following
functions will be enabled.
TV Auto If a connected HDMI device starts playing
Input video or audio, the TV will automatically
Switch switch to the appropriate HDMI input.
TV Auto If a REGZA-LINK device is turned on, the
Power TV turns on automatically.
Device If the TV is turned off the TV will send a
Auto message to turn off all of the REGZA-LINK
Standby devices connected to the TV.
From this item, you can set your audio output
preference to the TV speakers or the audio
Speaker receiver speakers. When this item is set to
Audio Receiver, the TV remote can be used to
Preference
adjust or mute the volume of the audio. This
item will be grayed out unless a REGZA-
LINK compatible audio receiver is connected.
Note: When you turn on the Audio Receiver, change its input
source, or adjust the sound volume, the sound will be output
from the audio receiver's speakers even if TV Speakers has
been selected. Turn the TV off and on again to output the
sound from the TV speakers.
To set the REGZA-LINK® Setup:
1 From the Setup menu, highlight REGZA-LINK Setup and
press Em).
2 Press A or Y to highlight Enable REGZA-LINK.
3 Press < or » to select On.
Note: If you select Enable REGZA-LINK Off, the other items
will be grayed out.
4 Press A or Y to highlight the REGZA-LINK Setup item
you want to use, and press € or > to select On or desired
mode.
* TV Auto Input Switch: On/Off
* TV Auto Power: On/Off
* Device Auto Standby: On/Off
* Speaker Preference: TV Speakers/Audio Receiver
Y To save the new settings, highlight Done and press 69.
To revert to the factory defaults, highlight Reset and
press Em).
Displaying TV status information
To display TV status information using RECALL:
ECALL
Press “$ on the remote control.
The following information will display (1f applicable):
* Current input (ANT/CABLE, VIDEO 1, etc.)
+ If ANT/CABLE is the current input, either “CABLE” (for
cable TV) or “ANT” (for over-the-air broadcasts).
* Channel number (if in ANT/CABLE mode)
* Channel label (1f set)
* Digital signal strength indicator (bar graph in lower right
corner of box; for ATSC signal only)
* Stereo, Mono or SAP audio status (when HDMI input
mode, Dolby Digital or PCM)
* Video resolution
Aspect ratio of incoming video signal (4:3 or 16:9)
* V-Chip rating status
* Game Timer (if set)
To close the RECALL screen:
Press "3 again.
To display TV status information using INFO:
Press "© on the remote control.
The following additional information will display for off air
digital channels (if applicable):
* Title
* Duration
* Detailed description
Note: The location of the banner can be moved to the top or
bottom of the screen by pressing A or Y while the RECALL or
INFO display is on-screen.
Understanding the auto power off
feature
The TV will automatically turn itself off after approximately 15
minutes if it is tuned to a vacant channel or a station that completes
its broadcast for the day. This feature functions in ANT/CABLE
mode only.
Understanding the last mode
memory feature
If the power is cut off while you are viewing the TV, the
Last Mode Memory feature automatically turns on the
TV when the power is resupplied.
Note: If it's possible, and you will be away from the TV for an
extended period of time you should unplug the power cord.
45
">
