Breville Customer Service Centre
Breville Customer Service Centre
Australian Customers
New Zealand Customers
Mail: PO Box 22
Botany, NSW, 2019
AUSTRALIA
Mail:
Private Bag 94411
Greenmount, Auckland
NEW ZEALAND
Phone: 1300 139 798
Phone: 0800 273 845
Fax:
Fax:
(02) 9384 9601
Email: Customer Service:
[email protected]
0800 288 513
Email: Customer Service:
[email protected]
www.breville.com.au
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2013.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
This model number includes a BSB510 Breville Stick Mixer motor unit.
Alternatively any existing Breville BSB510 Stick Mixer motor unit can be used with this Model Pack.
BSB530 Issue - E13
TYPESET V1
the All In One™
Instruction Booklet
BSB530
TYPESET V1
CONGRATULATIONS
on the purchase of your Breville product
Contents
4
Breville recommends safety first
8
Know your Breville product
10
Assembly & operation of your
Breville product
21
Care, cleaning & storage of your
Breville product
26Troubleshooting
28
Food preparation guide
32Recipes
3
Breville recommends safety first
At Breville we are very safety conscious. We design and
manufacture consumer products with the safety of you, our
valued customer, foremost in mind. In addition we ask that you
exercise a degree of care when using any electrical appliance
and adhere to the following precautions.
Important safeguards
Read all
instructions
BEFORE USE AND
SAVE FOR FUTURE
REFERENCE
• Remove any packaging
material and promotional
stickers before using the
stick mixer for the first time.
• Do not place the stick mixer
near the edge of a bench
or table during operation.
Ensure the surface is level,
clean and free of water,
flour, etc.
• Do not place the stick mixer
on or near a hot gas or
electric burner, or where it
could touch a heated oven.
• If using the stick mixer
to blend hot food in a
saucepan over heat, remove
the saucepan from the
heat source and ensure
the power cord and body
of appliance are also kept
away from any heat source.
4
• Take care when handling
the stick mixer, attachments
and sharp cutting blades,
when emptying the bowl
and during cleaning.
Remember the blade and
attachments are very sharp
and should be kept out of
the reach of children.
• Always make sure the stick
mixer is completely and
properly assembled before
operating.
• Ensure the stick mixer is
turned off at the trigger
switch, the power is
switched off at the power
outlet and the cord
is unplugged from the
power outlet before
attempting to attach any
of the accessories.
• Do not use attachments
other than those provided
with the stick mixer.
• Only use the whisk
attachment for the recipes
contained in this instruction
booklet.
Breville recommends safety first
• Do not use the whisk
attachment for anything
other than its intended use.
• Do not attempt to operate
the stick mixer by any
method other than those
described in this booklet.
• Do not process hot or
boiling liquids in food
processor bowl – allow
liquids to cool before
placing into the food
processor bowl.
• Do not operate the
appliance continuously
for more than 1 minute.
Allow the motor to rest for 1
minute between each use.
• Never mix dry, thick or
heavy mixtures for more
than 30 seconds. Stop
the operation and stir
the ingredients before
continuing. Allow the motor
to rest for
1 minute between each use.
• When using heavy loads,
the appliance should not be
operated for more than
30 seconds.
SAVE THESE
INSTRUCTIONS
• Always ensure the stick
mixer is turned off, the
power is switched off at the
power outlet and the cord is
unplugged from the power
outlet before attempting to
move the appliance, when
not in use, if left unattended
and before disassembling,
cleaning or storing.
• If food becomes lodged
around the processing
blade or in the blade guard,
release the ON button,
switch the power off at the
power outlet and unplug
the cord. Use a spatula to
dislodge the food. Do not
use fingers as the blades
are sharp.
• Do not remove the stick
mixer from ingredients
during operation. Ensure
the appliance is switched
off and has stopped turning
before removing, to avoid
contact with moving blade
or whisk.
• Do not leave the stick mixer
unattended when in use.
• To protect against electric
shock do not immerse
the motor body, cord or
power plug in water or any
other liquid.
5
Breville recommends safety first
• Keep the appliance clean.
Follow the cleaning
instructions provided in
this book.
• Do not use the stick
mixer/stick blender with
wet hands.
• Do not push food into
the food chute with your
fingers or other utensils.
Always use the food pusher
provided.
• Keep fingers, hands, knives
and other utensils away
from moving blade
and discs.
• Do not place hands or
fingers in the processing
bowl of the food processor
unless the motor,
processing blade, dough
blade or disc has come to
a complete stop. Ensure
the OFF button has been
pressed to switch the motor
off and the appliance is
switched off at the power
outlet and the power cord
is unplugged before
removing the lid from the
processing bowl.
6
IMPORTANT
SAFEGUARDS FOR
ALL ELECTRICAL
APPLIANCES
• Unwind the cord fully
before use.
• Do not let the cord hang
over the edge of a table or
counter, touch hot surfaces
or become knotted.
• This appliance can be
used by children aged
from 8 years and above
and persons with reduced
physical, sensory or mental
capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the
appliance in a safe way
and understand the
hazards involved.
• Keep the appliance
and its cord out of reach
of children.
• Children shall not play with
the appliance.
Breville recommends safety first
• It is recommended to
regularly inspect the
appliance. Do not use the
appliance if power supply
cord, plug or appliance
becomes damaged in any
way. Return the entire
appliance to the nearest
authorised Breville service
centre for examination
and/or repair.
• Cleaning and user
maintenance shall not be
made by children without
supervision.
• Any maintenance, other
than cleaning, should be
performed at an authorised
Breville Service Centre.
• This appliance is for
household use only. Do
not use this appliance for
anything other than its
intended use. Do not use in
moving vehicles or boats.
Do not use outdoors.
• The installation of a
residual current device
(safety switch) is
recommended to provide
additional safety protection
when using electrical
appliances. It is advisable
that a safety switch with a
rated residual operating
current not exceeding
30mA be installed in
the electrical circuit
supplying the appliance.
See your electrician for
professional advice.
7
TYPESET V1
KNOW
your Breville product
KNOW your Breville PRODUCT
A
B
J
I
H
G
C
D
E
K
L
F
M
A.
B.
C.
D.
E.
F.
G.
H.
N
Speed Control Dial
Easy Grip Trigger Switch
Motor Body
Processing Gear Box
Clear Lid
1.6L Chopping Bowl
Feed Chute
Whisk
O
P
I. Stainless Steel Blending Leg
J. Detachable Mashing Gear Box
K. Detachable Mashing Leg
L. Quad Blade
M. Variable Slicing Disc
N. Reversible Shredding Disc
O. Storage Base
P. Spindle
NOT SHOWN
Quad Blade Cover
9
TYPESET V1
ASSEMBLY & OPERATION
of your Breville product
ASSEMBLY & OPERATION
Before first use
To attach the blending leg
Remove any packaging material and
promotional labels. Remove the blending
leg from the mixer motor body and wash
it in warm soapy water (refer to assembly
instructions in this booklet). Rinse and dry
thoroughly. Ensure no water remains inside
the blending leg to avoid water running into
the motor body when reattached.
Disassemble and wash the chopping blade,
chopper bowl, chopper bowl lid, whisk,
storage lid, and blending jug in warm soapy
water, rinse and dry thoroughly. Ensure no
water remains on the chopper bowl lid or
whisk attachment to avoid water running
into the motor body when reattached.
Hold the blending leg with the blades down,
and align the top end of the blending leg
with the corresponding end of the motor
body and push until the blending leg clicks
and locks onto the motor body.
Always ensure blending leg is dry, and no
water left inside, before reattaching.
NOTE
The detachable blending leg,
chopping bowl (without the gearbox),
quad blade, variable masher, whisk
can also be washed in the dishwasher.
The whisk gear box, processor gear
box, masher gear box and motor
body are not dishwasher safe – see
the care and cleaning section of this
booklet for cleaning instructions of
these parts.
This stick mixer is a versatile appliance
that can be attached to:
• The stainless steel blending leg – for use
as a stick mixer.
• The food processor bowl with quad
blade, variable slicing disc, reversible
shredding disc - for use as a mini
food processor.
• The variable mashing leg – for use as
mashing vegetables.
• The whisk attachment – for use as a
hand whisk.
Using as a stick mixer
Ensure the blending leg is assembled to the
motor body as detailed above.
1. Place food to be processed into a
sufficiently large mixing bowl or
saucepan (do not use the food processor
bowl as this may damage either the stick
mixer or the bowl). The bowl should only
be ½ full or less when blending liquids
or when making a puree of fruit
and/or vegetables.
2. Insert the plug into a 230/240V power
outlet and turn the power on.
3. Turn the dial at the top of motor body,
select a speed from 1 to 15.
NOTE
If selecting a higher speed, it is
recommended that you start on
a slow speed and then increase to
high speed to avoid splattering and
over-processing.
11
ASSEMBLY & OPERATION
4. Place the blending leg as deeply as
possible into the bowl and press the
trigger switch to turn the stick mixer on.
The button must be held for the required
duration of operation.
5. Work through the ingredients in
the bowl with a gentle raising and
lowering motion.
6. Switch off the motor by releasing the
trigger switch.
7. Ensure the motor has completely
stopped before lifting the blender out of
the bowl.
8. When processing has finished, switch
off at the power outlet and remove the
power plug.
To detach the blending leg
Ensure the trigger switch is released, the
power is turned off at power point and the
appliance is unplugged. Hold the motor
body with one hand, and using thumb and
finger of the other hand, press on the two
EJECT buttons on either side of the motor
body. Pull the motor body away from the
blending leg to detach.
Recommendations when using
as a stick mixer
• The stick mixer blends foods and
liquids rapidly, therefore it is easy to
over process. Remember when using the
blending leg to stop the stick mixer and
check food throughout the operation.
• Use caution when blending hot food as it
can splatter.
• The stainless steel blending leg allows
for hot food to be processed directly
in the saucepan. This makes blending
soups and sauces very easy.
• For safety reasons remove saucepan
away from the heat before processing.
• Ensure the body of the appliance and
power cord are kept away from any
heat source.
• When pureeing and blending, cut food
into uniform sizes. This will ensure
smooth and consistent results.
• Warm all liquids to be added to soups
and purees, this will ensure even
blending.
• Do not operate the appliance
continuously for more than 1 minute.
Allow the motor to rest for 1 minute
between each use.
If food becomes lodged around the
processing blade or in the blade guard,
follow the safety instructions below:
1. Release the trigger switch, the power off
at the power outlet and unplug the cord.
2. Use a spatula to carefully dislodge the
food. Do not use fingers as the blades
are sharp.
3. After the food has been removed and
blades are clear, plug the appliance back
into the power supply, switch the power
on and continue blending.
12
ASSEMBLY & OPERATION
USING THE FOOD
PROCESSOR BOWL
Attaching Gearbox to Food
Processing Bowl Lid
The gearbox should be placed into the food
processor lid. It should click into place.
To Attach the Food
Processing Bowl, Food
Processor Attachments
and Lid
1. Remove the food processing bowl from
the storage unit and place onto a bench
ensuring that the surface is clean
and level.
2. Choose one of the following food
processor attachments:
a) Quad blade
b) Adjustable slicer
c) Reversible shredder
3. There is a common spindle that is
used across all of the three food
processor attachments.
When using the
reversible shredder
1. Place the spindle, into the centre of the
food processing bowl.
To attach the motor, click into place onto
the gearbox.
CAUTION
Caution should be taken when
handling the shredding disc.
13
ASSEMBLY & OPERATION
2. Holding the reversible shredder disc,
notice that there is a large grater and
small grater, place the side you require
up. Place over the centre of the spindle
and ensure that it is pushed down firmly.
CAUTION
Caution should be taken when
handling the adjustable slicing disc
and ensure that blade is in the storage
or 0 position.
2. The adjustable slicing disc has 18
precise settings. To adjust the settings
hold the adjustable slicing disc by the
edge (on the opposite side to the cutting
blade) with one hand and turn the
rotating collar to the desired setting with
the other hand.
3. Place the lid into position and ensure
that it is on correctly.
3. Place the adjustable slicing disc onto
the spindle. Ensure that it is pushed
down correctly.
When using the
adjustable slicer
1. Place the spindle in the centre of the
food processing bowl.
14
ASSEMBLY & OPERATION
4. Place the lid into position and ensure
that it is on correctly.
When using the quad blade
1. Using care, hold the quad blade in one
hand, with the other hand, place the
spindle through the centre of the quad
blade from underneath. The quad should
self-locate at the base of the spindle.
The quad blade will sit loosely on the
spindle but will lock into place during
processing.
4. Once the blade or disc has been
selected for the food processor you can
now process food. Place the food inside
the processing bowl. If using the quad
blade. Do not exceed the maximum
(MAX) marking.
5. Insert the gear box into the lid of the
food processor.
NOTE
CAUTION
Caution should be taken when
handling the quad blade as the blades
are extremely sharp.
2. Place the quad blade and spindle into
the centre of the food processing bowl.
3. Place the lid into position and ensure
that it is on correctly.
Always place the quad blade into the
food processor prior to placing the
food into the food processor. When
using the disc’s adjustable slicer and
reversible shredder these both can
be placed into the food processor
prior to processing food. Some foods,
such as nuts, can stop the quad blade
from engaging the built in safety
mechanism. If you have troubles
closing the lid with ingredients such
as this we advise to load these through
the feed chute.
15
ASSEMBLY & OPERATION
To use the FOOD PROCESSOR
For food preparation tips and recipes refer to
the recipe section of this booklet.
1. Insert the plug into a 230/240V power
outlet and turn the power on.
2. Select a speed between 1–15 on the
speed control dial.
5. When processing has finished switch
off the motor by releasing the trigger
switch, switch off at the power outlet and
remove the power plug.
3. Press the trigger switch to turn
the appliance on and start the
processing action.
6. Detach the food processing bowl and lid
(refer to instructions). Remove the lid
from the food processor bowl. Carefully
remove the food processing blades
or quad blade and use a spatula to
scrape off any attached food back into
food processing bowl.
TO DETACH THE FOOD
PROCESSING BOWL AND LID
Ensure the switch is released, power is
turned off at power point and the appliance
is unplugged.
Hold the motor body with one hand and
using thumb and finger of the other hand,
press on the two EJECT buttons on either
side of the motor body. Pull the motor body
away from the chopper bowl lid to detach.
4. Feed the food through the feed chute
of the food processor, using the food
pusher to push it down.
CAUTION
Only use the small pusher with
the large pusher resting inside the
feed chute.
16
ASSEMBLY & OPERATION
TO DETACH the gearbox
from the lid
• To remove the gearbox grasp
the gearbox and lift up from the
processing lid.
CAUTION
DO NOT process hard foods such as
coffee, grains or chocolate in lumps, as
damage to the blade may result.
DO NOT process boiling or hot foods in
the food processing bowl.
NEVER remove the blade from the bowl
before food processing is completed.
Processing hard spices will cause the
chopper bowl to become cloudy over
time. Hard spices are best suited to a
spice grinder with a metal bowl.
RECOMMENDATIONS WHEN USING
THE STICK MIXER WITH THE FOOD
PROCESSING BOWL
• Do not operate the stick mixer when the
food processing bowl is empty.
• The bottom of the food processing bowl
features a anti-slip rubber rim. This
keeps the food processing bowl stable,
however it is recommended during
processing to hold the motor body with
one hand and the food processing bowl
and lid with the other.
• When processing, cut food into uniform
sizes to ensure quicker, even and more
consistent results.
• The stick mixer blends foods and
liquids rapidly, therefore it is easy to
over process. Remember to check food
throughout the operation.
Assembly of the potato
masher leg
Before first use
Remove any packaging material and
promotional labels. Wash blade and two
parts of the mashing leg before use.
CAUTION
Never immerse the motor body or
gearbox in water or any other liquid.
NOTE
If the variable masher leg is already
assembled start from step 3.
NOTE
When using the shredding or slicing
disc do not allow the processing bowl
to fill with food beyond the MAX level
indicated. Processing food beyond
this level could damage parts of the
bowl and lid
17
ASSEMBLY & OPERATION
1. Holding the outer leg and insert the
gearbox making sure ALIGN arrows
are aligned.
3. Rotate gearbox while holding outer leg
to lock into place until it clicks.
2. Hold both outer leg and gearbox firmly
with one hand and insert inner leg until
it clicks and locks into place.
4. Align the mashing leg with the motor
body and push the two parts together
until it clicks.
5. Place blade on underside of the mashing
head. To lock the blade rotate in a
anticlockwise direction. Blade will not
attach if the leg is not attached to the
motor body.
18
ASSEMBLY & OPERATION
TO USE THE POTATO MASHER LEG
For food preparation tips and recipes
refer to the recipes section. Ensure the
potato masher is completely and properly
assembled.
1. Place food to be mashed into a
sufficiently large mixing bowl or
container or in saucepan.
2. Insert the plug into a 230/240V power
outlet and turn the power on.
3. Select the desired setting on the variable
mashing leg: textured, smooth or
creamy.
4. Select a high speed on the speed
control dial.
5. Place the potato masher into food and
press the trigger switch to turn the
masher on.
6. Move the masher through the
ingredients with a gentle raising and
lowering action until desired texture
is achieved.
7. Switch off the motor by releasing the
trigger switch before lifting the masher
out of the bowl. Switch off at the power
outlet and remove the power plug.
TO DETACH THE POTATO
MASHING LEG
1. Ensure the trigger switch is released, the
power is turned off at power point and
the appliance is unplugged.
2. Before removing motor body, remove
masher blade by holding onto the blade
and turning clockwise to unlock.
3. Once blade is removed, hold the motor
body with one hand, and using thumb
and finger of the other hand, press on
the two EJECT buttons on either side
of the motor body. Pull the motor body
away from the masher to detach.
.
NOTE
Mashing blade will not attach/detach
if the leg is not attached to the
motor body.
RECOMMENDATIONS WHEN USING
WITH THE POTATO MASHING LEG
• Release the trigger switch and ensure
the masher has completely stopped
turning before removing the masher
from the food during operation.
• Place the mixing bowl on a damp cloth
during mashing. This will keep the
mixing bowl stable.
USING AS A WHISK
Remove blending leg from motor body
(follow the instructions 'To detach the
blending leg').
1. Align the whisk gear box to the hole in
the underside of the motor body and
push the whisk in until it clicks and
locks into place.
19
ASSEMBLY & OPERATION
TO USE THE WHISK
For food preparation tips and recipes refer
to the recipes section. Ensure the whisk is
completely and properly assembled.
1. Place food to be processed into a
blending jug or a sufficiently large
mixing bowl or container.
2. Insert the plug into a 230/240V power
outlet and turn the power on.
3. Select a speed between 1–15 on the
speed control dial.
4. Place the whisk into food and press the
trigger switch to turn the whisk on.
5. Move the whisk through the ingredients
with a gentle raising and lowering action
until desired texture is achieved.
6. Switch off the motor by releasing the
trigger switch before lifting the whisk
out of the bowl. Switch off at the power
outlet and remove the power plug.
TO DETACH THE WHISK
Ensure the trigger switch is released, the
power is turned off at power point and the
appliance is unplugged. Hold the motor
body with one hand, and using thumb and
finger of the other hand, press on the two
EJECT buttons on either side of the motor
body. Pull the motor body away from the
whisk to detach.
20
RECOMMENDATIONS WHEN USING
THE WHISK ATTACHMENT
• Do not allow the whisk to hit the bottom
or sides of mixing bowl while the
appliance is in operation, as this may
damage the whisk.
• To incorporate air into the ingredients
when whisking, use a sufficiently deep,
wide container and move the whisk
through the ingredients with a gentle
raising and lowering action.
• Release the trigger switch and ensure
the whisk has completely stopped
turning before removing the whisk from
the food during operation.
• Place the mixing bowl on a damp cloth
during whisking. This will keep the
mixing bowl stable.
• Always use fresh chilled cream and
fresh eggs at room temperature to
achieve greater and more stable volume
when whisking.
• Always ensure the whisk and mixing
bowl are completely clean and free of fat
before whisking egg whites.
• It is recommended to use the highest
speed when whisking egg whites
and cream.
STORAGE
Before storage, turn the power off at
the power outlet and then remove the
plug. Ensure the appliance is clean and
completely dry.
Attach/assemble chopper bowl lid to the
chopper bowl, place chopper bowl inside
blending jug, attach storage lid to the
bottom of the blending jug (non-slip base).
TYPESET V1
CARE, CLEANING
& STORAGE
of your Breville product
PAge header.....
Care,
Cleaning & Storage
Motor body
NOTE
To remove any food residue wipe the motor
body and cord with a damp cloth only.
Do not use abrasive cleaners or steel wool.
Never immerse the motor body in water or
any other liquid. Do not place motor body
in dishwasher.
The lid is dishwasher safe remove the
removable gear box from the lid prior
to placing in the dishwasher.
CAUTION
Never immerse the motor body or
gearbox in water or any other liquid.
Blending Leg
Before cleaning, turn the power off at the
power outlet and then remove the plug.
Remove the motor body from the stainless
steel blending leg. The stainless steel
blending leg can be hand washed in hot
soapy water, rinsed and dried thoroughly
after each use. Alternatively, the blending
leg can also be washed in the dishwasher.
Do not use abrasive cleaners or steel wool.
QUICK WASH: Between each processing
task, with the motor body attached and
turned on at the power outlet, place the
stainless steel blending leg and blade
assembly only in to a jug of water and press
the trigger switch to turn on for 5 seconds.
This will remove any food on the blade and
leg and allow you to continue onto the next
processing task.
FOOD PROCESSING BOWL, FOOD
PROCESSING BOWL LID, QUAD
BLADE, ADJUSTABLE SLICING DISC
& REVERSIBLE SHREDDER
Before cleaning, turn the power off at the
power outlet and then remove the plug.
Remove the motor body from the food
processing bowl lid and gear box. Remove
the food processing bowl lid and quad
blade | processing discs from the food
processing bowl.
22
The food processing bowl, bowl lid, quad
blade and processing discs should be hand
washed in hot soapy water, rinsed and dried
thoroughly after each use. Alternatively,
the food processing bowl, bowl lid, quad
blade, adjustable slicing disc and reversible
shredder can also be washed in the
dishwasher. The quad blade comes with a
cover for your safety. This cover can be used
on the blade in the dishwasher. Do not use
abrasive cleaners or steel wool.
CARE & CLEANING OF THE
GEARBOX
The gearbox should always be removed from
the lid prior to any cleaning.
The gearbox lifts out of the lid by pulling
it up.
NOTE
The gear box is not dishwasher safe
and should never be immersed in
liquid at all.
To clean the gearbox, remove from the
lid and wipe down with a damp cloth
only. Do not use abrasive cleansers or
steel wool.
Care, Cleaning & Storage
POTATO MASHER LEG
Before cleaning, turn the power off at the
power outlet and then remove the plug. The
masher leg can be hand washed in hot soapy
water, rinsed and dried thoroughly after
each use.
3. Unclip the gear box from motor body,
turn the masher leg to align and remove
the inner and outer legs from the gear
box together.
To disassemble the potato
mashing leg
1. Ensure the motor is unplugged. Before
removing the masher leg, unlock
the blade by rotating in a clockwise
direction. Blade will not detach once the
masher leg is released from motor body.
2. Once the blade is removed hold the
motor body with one hand, and using
thumb and finger of the other hand,
press on the two EJECT buttons on
either side of the motor body. Pull the
motor body away from the masher
to detach.
4. The inner and outer legs can now
be separated.
Both of the legs can now be washed in hot
soapy water, rinsed and dried thoroughly.
Alternatively, the masher can be washed in
the dishwasher.
CAUTION
Do not use abrasive cleaners or steel
wool.
NOTE
Masher gear box is not dishwasher
safe.
23
Care, Cleaning & Storage
WHISK
Before cleaning, turn the power off at the
power outlet and then remove the plug.
Remove the motor body from the whisk.
The whisk can be hand washed in hot soapy
water, rinsed and dried thoroughly after
each use. Alternatively, the whisk can also
be washed in the dishwasher. Do not use
abrasive cleaners or steel wool. Whisk gear
box is not dishwasher safe.
Storage
Before storage, turn the power off at
the power outlet and then remove the
plug. Ensure the appliance is clean and
completely dry. Attach/assemble processing
bowl lid to the processing bowl and place
processing bowl onto the storage unit with
all the attachments.
NOTE
The adjustable slicing disc is stored
under the food processing bowl, make
sure that the adjustable blade is set to
STORAGE POSITION.
24
NOTES
25
TYPESET V1
TROUBLESHOOTING
PAge header.....
TROUBLESHOOTING
Problem
Solution
Blades don’t turn when
processing.
• May be too much food in bowl. Reduce quantity.
Unable to lock lid
into place.
• Spindle may be out of position. Remove lid, straighten
spindle as vertical as possible and reposition lid.
• Pieces of food, such as meat are too large. Reduce size.
• Food may be stuck underneath the quad blade
preventing the lid from being locked into place. Food
such as nuts can be loaded through the feed chute.
Gear box in lid jumps out
of lid when processing.
• Replace gear box and ensure that the control grip is
held vertically and firmly.
Masher leg won’t attach
onto masher drive.
• Ensure mashing leg and gear box arrow graphics are
vertically aligned. Twist masher leg anticlockwise to
lock for use.
Blades won’t remove
from potato masher.
• Mashing leg must be assembled to gearbox and motor
body to remove blade. Rotate blade clockwise to remove.
Grating disc slows down
when grating.
• Grating has exceeded Max level. Empty bowl and
continue to grate.
• Too much force is being used when grating. Reduce
force when pushing.
Processing bowl does not
sit flat onto storage base.
• Ensure adjustable slicing disc is set to ‘Storage Position’.
Motor sounds like
it is not coping with
processing load.
• Speed may not be correct. Refer to processing guide for
correct speeds.
27
TYPESET V1
FOOD PREPARATION
CHART
Food Preparation CHART
Food
Type
Carrot
Attachment
Type
Disk
type
Speed
Blade
setting thickness
RECOMMENDED
QUANTITY
Food Processor
Grater fine
9–13
–
1–2 carrots at a time,
depending on size
Food Processor
Grater coarse
9–13
–
1–2 carrots at a time,
depending on size
Food Processor
Grater fine
11–15
–
1–2 zucchini at a
time, depending on
size
Food Processor
Grater coarse
11–15
–
1–2 zucchini at a
time, depending on
size
Food Processor
Variable
slicer
9–13
1–6mm
1–2 zucchini at a
time, depending on
size
Cucumber
Food Processor
Variable
slicer
9–13
2–5mm
1–2 cucumber at a
time, depending on
size
Tomato
Food Processor
Variable
slicer
9–11
4–6mm
Use firm tomatoes
Cabbage
Food Processor
Variable
slicer
9–11
2–6mm
Cut to size to fit
shoot
Leek
Food Processor
Variable
slicer
9–13
2–6mm
White part only
Onion
Food Processor
Variable
slicer
9–13
2–6mm
Cut in half
Chicken
breast/
thigh fillets
Food Processor
Quad
blade
15
–
700g max cut into
2.5cm cubes
Lean Beef
Food Processor
Quad
blade
15
–
700g max cut into
2.5cm cubes
Lean Pork
Food Processor
Quad
blade
15
–
700g max cut into
2.5cm cubes
Fish fillets
Food Processor
Quad
blade
15
–
700g max cut into
2.5cm cubes
Zucchini
29
Food Preparation CHART
Food
Type
Cheddar/
tasty
Attachment
Type
Disk
type
Speed
Blade
setting thickness
RECOMMENDED
QUANTITY
Must be well chilled
Food Processor
Greater
fine
15
–
Food Processor
Grater coarse
15
–
Mozzarella
Food Processor
Grater coarse
15
–
Place in freezer for
20 minutes before
grating
Parmesan
Food Processor
Grater fine
15
–
Must be well chilled
Food Processor
Quad
blade
15
–
Cut into 1cm cubes
Milkshakes,
smoothies,
fruit
frappes,
cocktails
Blending Leg
–
11–15
–
Use chilled milk.
Blend for 30 seconds
at a time.
Soups,
baby food
Blending Leg
–
11–15
–
Blend until smooth,
checking desired
consistency every
30 seconds
Ice
Blending Leg (Do
not use chopping
bowl for ice)
–
15
–
Crush ice for 20–30
seconds
30
PAge header.....
Food
Preparation CHART
Food
Type
Attachment
Type
Disk
type
Speed
Blade
setting thickness
RECOMMENDED
QUANTITY
Cream
Whisk
–
11–15
–
Whisk for 1 minute
at a time, rest for
1 minute between
each use
Nuts
Food Processor
Quad
blade
15
–
250g for 30 seconds
at time until desired
consistency is
achieved. Wait 30
seconds between
each interval.
Bread
crumbs
Food Processor
Quad
blade
15
–
2–3 slices cut into
quarters
Biscuit
crumbs
Food Processor
Quad
blade
15
–
250g max
31
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement