s900 dp specification
ST 3000 Smart Pressure Transmitter
Series 900 Differential Pressure Models
STD924
STD930
STD974
0 to 400 inH2O
0 to 100 psi
0 to 3000 psi
0 to 1,000 mbar
0 to 7,000 mbar
0 to 210,000 mbar
34-ST-03-65
9/19/05
Specification and
Model Selection
Guide
Introduction
In 1983, Honeywell introduced the first
Smart Pressure Transmitter― the ST
3000®. In 1989, Honeywell launched
the first all digital, bi-directional protocol
for smart field devices. Today, its
ST 3000 Series 900 Differential
Pressure Transmitters continue to bring
proven “smart” technology to a wide
spectrum of pressure measurement
applications, from furnace combustion
airflow rate to hydrostatic tank gauging.
The ST 3000 S900 Differential
Pressure Transmitter can be used with
any primary flow element to provide
proven, repeatable flow measurement.
All ST 3000 transmitters can provide a
4-20 mA output, Honeywell Digitally
Enhanced (DE) output, HART* output,
or FOUNDATION™ Fieldbus output.
When digitally integrated with
Honeywell’s Process Knowledge
System™, EXPERION PKS™,
ST 3000 instruments provide a more
accurate process variable as well as
advanced diagnostics.
Honeywell’s cost-effective ST 3000
S900 transmitters lead the industry in
reliability and stability:
•
•
Stability = +/-0.01% per year
Reliability = 470 years MTBF
Figure 1—Series 900 Differential Pressure Transmitters feature proven
piezoresistive sensor technology.
The devices provide comprehensive self-diagnostics to help users
maintain high uptime, meet regulatory requirements, and attain high
quality standards. S900 transmitters allow smart performance at
analog prices. Accurate, reliable and stable, Series 900 transmitters
offer greater turndown ratio than conventional transmitters.
"Honeywell transmitters operating in the digital mode using
Honeywell's Digitally Enhanced (DE) protocol make diagnostics
available right at the control system's human interface. Equally
important, transmitter status information is continuously displayed to
alert the operator immediately of a fault condition. Because the
process variable (PV) status transmission precedes the PV value, we
are guaranteed that a bad PV is not used in a control algorithm. In
addition, bi-directional communication provides for remote transmitter
configuration directly from the human interface, enabling management
of the complete loop.”
Maureen Atchison, DuPont
Site Electrical & Instrumentation Leader
34-ST-03-65
Page 2
Description
The ST 3000 transmitter can replace any 4 to 20 mA output transmitter in
use today and operates over a standard two-wire system.
The measuring means is a piezoresistive sensor, which actually contains
three sensors in one. It contains a differential pressure sensor, a
temperature sensor, and a static pressure sensor.
Features
•
Choice of linear or square
root output conformity is a
simple configuration selection.
•
Direct digital integration with
Experion PKS and other
control systems provides local
measurement accuracy to the
system level without adding
typical A/D and D/A converter
inaccuracies.
•
Unique piezoresistive sensor
automatically compensates
input for temperature and
static pressure.Added “smart”
features include configuring
lower and upper range
values, simulating accurate
analog output, and selecting
preprogrammed engineering
units for display.
•
Smart transmitter capabilities
with local or remote
interfacing means significant
manpower efficiency
improvements in
commissioning, start-up, and
ongoing maintenance
functions.
Microprocessor-based electronics provide higher span-turndown ratio,
improved temperature and pressure compensation, and improved
accuracy.
The transmitter’s meter body and electronics housing resist shock,
vibration, corrosion, and moisture. The electronics housing contains a
compartment for the single-board electronics, which is isolated from an
integral junction box. The single-board electronics is replaceable and
interchangeable with any other ST 3000 Series 100 or Series 900 model
transmitter.
Like other Honeywell transmitters, the ST 3000 features two-way
communication between the operator and the transmitter through our
Smart Field Configurator (SFC). You can connect the SFC anywhere that
you can access the transmitter signal lines.
The SCT 3000 Smartline® Configuration Toolkit provides an easy way to
configure instruments using a personal computer. The toolkit enables
configuration of devices before shipping or installation. The SCT 3000 can
operate in the offline mode to configure an unlimited number of devices.
The database can then be loaded downline during commissioning.
34-ST-03-65
Page 3
Specifications
Operating Conditions – All Models
Parameter
Reference
Condition
(at zero static)
Rated Condition
Operative Limits
Transportation and
Storage
°C
°F
°C
°F
°C
Ambient Temperature
25 ±1
77 ±2
-40 to 85
-40 to 185
-40 to 85
-40 to 185 -55 to 125 -67 to 257
Meter Body Temperature
25 ±1
77 ±2
-40 to 110*
-40 to 230*
-40 to 125
-40 to 257 -55 to 125 -67 to 257
Humidity
%RH
Vacuum Region - Minimum
Pressure
mmHg absolute
inH2O absolute
°F
10 to 55
0 to 100
0 to 100
Atmospheric
Atmospheric
25
13
2 (short term **)
1 (short term **)
Supply Voltage, Current,
and Load Resistance
Voltage Range: 10.8 to 42.4 Vdc at terminals
Current Range: 3.0 to 21.8 mA
Load Resistance: 0 to 1440 ohms (as shown in Figure 2)
Maximum Allowable
Working Pressure
(MAWP)
***STD924-AXX, BXX, EXX, FXX, JXX = 3000 psi, 210 bar
(ST 3000 products are rated to
Maximum Allowable Working
Pressure. MAWP depends on
Approval Agency and transmitter
materials of construction.)
***STD930-AXX, BXX, EXX, FXX, JXX = 3000 psi, 210 bar
°C
°F
0 to 100
°STD924-CXX, DXX, GXX, HXX, KXX, LXX = 4500 psi, 310 bar
°STD930-CXX, DXX, GXX, HXX, KXX, LXX = 4500 psi, 310 bar
°STD974 = 4500 psi, 310 bar
Static Pressure Limit = Maximum Allowable Working Pressure (MAWP) = Overpressure
Limit
* For CTFE fill fluid, the rating is –15 to 70°C (5 to 158°F). ** Short term equals 2 hours at 70°C (158°F). ***Static Pressure is de-rated to
2000 psi (140 bar) for temperatures below –15°C (5°F). °MAWP applies for temperature range –40 to 125 deg. C. However, Static Pressure
Limit is de-rated to 3000 psi from –26 deg C. to –40 deg. C. Consult factory for MAWP of ST 3000 transmitters with CSA approval.
1440
1200
Loop
Resistance
(ohms)
800
NOTE: A minimum of 250 ohms
of loop resistance is necessary
to support communications.
Loop resistance equals barrier
resistance plus wire resistance
plus receiver resistance.
650
450
250
= Operating Area
0
10.8 16.28 20.63 25
28.3
Operating Voltage (Vdc)
Figure 2—Supply voltage and loop resistance chart
37.0
42.4
21012
34-ST-03-65
Page 4
Performance Under Rated Conditions* - Model STD924 (0 to 400 inH2O/1000 mbar)
Parameter
Description
Upper Range Limit
inH2O
mbar
400 (39.2°F/4°C is standard reference temperature for inH2O range.)
1000
Minimum Span
inH2O
mbar
10
25
Note: Recommended minimum span in square root mode is 20 inH2O (50 mbar).
Turndown Ratio
40 to 1
Zero Elevation and Suppression
–5 to +100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
In Analog Mode: ±0.075% of calibrated span or upper range value (URV), whichever
is greater, terminal based.
For URV below reference point (25 inH2O), accuracy equals:
• Accuracy includes residual error
after averaging successive
readings.
25 inH2O
62 mbar
±0.025 + 0.05  span inH O or ±0.025 + 0.05 span mbar in % span
2 

In Digital Mode: ±0.0625% of calibrated span or upper range value (URV),
whichever is greater, terminal based.
For URV below reference point (25 inH2O), accuracy equals:
• For FOUNDATION Fieldbus use
Digital Mode specifications. For
HART use Analog Mode
specifications.
Zero Temperature Effect per
28°C (50°F)
(
25 inH2O
±0.0125 + 0.05  span inH O or ±0.0125 + 0.05
2 

)
62 mbar
( span
mbar) in % span
In Analog Mode: ±0.1625% of span.
For URV below reference point (50 inH2O), effect equals:
50 inH2O
±0.0125 + 0.15  span inH O or ±0.0125 + 0.15
2 

125 mbar
( span
mbar) in % span
In Digital Mode: ±0.15% of span.
For URV below reference point (50 inH2O), effect equals:
50 inH2O
±0.15  span inH O or ±0.15
2 

Combined Zero and Span
Temperature Effect per 28°C
(50°F)
125 mbar
( span
mbar) in % span
In Analog Mode: ±0.25% of span.
For URV below reference point (50 inH2O), effect equals:
50 inH2O
±0.10 + 0.15  span inH O or ±0.10 + 0.15
2 

125 mbar
( span
mbar) in % span
In Digital Mode: ±0.225% of span.
For URV below reference point (50 inH2O), effect equals:
50 inH2O
±0.075 + 0.15  span inH O or ±0.075 + 0.15
2 

Zero Static Pressure Effect per
1000 psi (70 bar)
125 mbar
( span
mbar) in % span
±0.1625% of span.
For URV below reference point (50 inH2O), effect equals:
50 inH2O
±0.0125 + 0.15  span inH O or ±0.0125 + 0.15
2 

125 mbar
( span
mbar) in % span
Combined Zero and Span Static
Pressure Effect per 1000 psi (70
bar)
±0.30% of span.
For URV below reference point (50 inH2O), effect equals:
Stability
±0.015% of URL per year
50 inH2O
±0.15 + 0.15  span inH O or ±0.15 + 0.15
2 

125 mbar
( span
mbar) in % span
* Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
34-ST-03-65
Page 5
Performance Under Rated Conditions* - Model STD930 (0 to 100 psi/7000 mbar)
Parameter
Description
Upper Range Limit
psi
bar
100
7
Minimum Span
psi
bar
5
0.35
Turndown Ratio
20 to 1
Zero Elevation and Suppression
–5 to +100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
In Analog Mode: ±0.075% of calibrated span or upper range value (URV), whichever
is greater, terminal based.
For URV below reference point (20 psi), accuracy equals:
•
•
±0.025 + 0.05
20 psi
1.4 bar
( span
psi) or ±0.025 + 0.05 ( span bar) in % span
In Digital Mode: ±0.0625% of calibrated span or upper range value (URV),
whichever is greater, terminal based.
For URV below reference point (20 psi), accuracy equals:
±0.0125 + 0.05
Zero Temperature Effect per
28°C (50°F)
20 psi
1.4 bar
( span
psi) or ±0.0125 + 0.05 ( span bar) in % span
In Analog Mode: ±0.1625% of span.
For URV below reference point (30 psi), effect equals:
±0.0125 + 0.15
30 psi
2 bar
( span
psi) or ±0.0125 + 0.15 ( span bar) in % span
In Digital Mode: ±0.15% of span.
For URV below reference point (30 psi), effect equals:
±0.15
Combined Zero and Span
Temperature Effect per 28°C
(50°F)
30 psi
2 bar
( span
psi) or ±0.15 ( span bar) in % span
In Analog Mode: ±0.25% of span.
For URV below reference point (30 psi), effect equals:
±0.10 + 0.15
30 psi
2 bar
( span
psi) or ±0.10 + 0.15 ( span bar) in % span
In Digital Mode: ±0.225% of span.
For URV below reference point (30 psi), effect equals:
±0.075 + 0.15
Zero Static Pressure Effect per
1000 psi (70 bar)
30 psi
2 bar
( span
psi) or ±0.075 + 0.15 ( span bar) in % span
±0.1625% of span.
For URV below reference point (30 psi), effect equals:
±0.0125 + 0.15
Combined Zero and Span Static
Pressure Effect per 1000 psi (70
bar)
±0.30% of span.
For URV below reference point (30 psi), effect equals:
±0.15 + 0.15
Stability
30 psi
2 bar
( span
psi) or ±0.0125 + 0.15 ( span bar) in % span
30 psi
2 bar
( span
psi) or ±0.15 + 0.15 ( span bar) in % span
±0.04% of URL per year
* Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
34-ST-03-65
Page 6
Performance Under Rated Conditions* - Model STD974 (0 to 3000 psi/210 bar)
Parameter
Description
Upper Range Limit
psi
bar
3000
210
Minimum Span
psi
bar
100
7
Turndown Ratio
30 to 1
Zero Elevation and Suppression
–0.6 and +100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
In Analog Mode: ±0.2% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (300 psi), accuracy equals:
• Accuracy includes residual error
after averaging successive
readings.
±0.05 + 0.15
300 psi
21 bar
( span
psi) or ±0.05+ 0.15 ( span bar) in % span
• For FOUNDATION Fieldbus use
Digital Mode specifications. For
HART use Analog Mode
specifications.
In Digital Mode: ±0.175% of calibrated span or upper range value (URV), whichever
is greater, terminal based.
For URV below reference point (300 psi), accuracy equals:
300 psi
21 bar
±0.025 + 0.15 span psi or ±0.025+ 0.15 span bar in % span
Zero Temperature Effect per
28°C (50°F)
In Analog Mode: ±0.2125% of span.
For URV below reference point (500 psi), effect equals:
(
±0.0125 + 0.20
)
(
)
500 psi
35 bar
( span
psi) or ±0.0125 + 0.20 ( span bar) in % span
In Digital Mode: ±0.20% of span.
For URV below reference point (500 psi), effect equals:
±0.20
Combined Zero and Span
Temperature Effect per 28°C
(50°F)
500 psi
35 bar
( span
psi) or ±0.20 ( span bar) in % span
In Analog Mode: ±0.325% of span.
For URV below reference point (500 psi), effect equals:
±0.125 + 0.20
500 psi
35 bar
( span
psi) or ±0.125 + 0.20 ( span bar) in % span
In Digital Mode: ±0.30% of span.
For URV below reference point (500 psi), effect equals:
±0.10 + 0.20
Zero Static Pressure Effect per
1000 psi (70 bar)
500 psi
35 bar
( span
psi) or ±0.10 + 0.20 ( span bar) in % span
±0.1625% of span.
For URV below reference point (500 psi), effect equals:
±0.0125 + 0.15
Combined Zero and Span Static
Pressure Effect per 1000 psi (70
bar)
±0.30% of span.
For URV below reference point (500 psi), effect equals:
±0.15 + 0.15
Stability
500 psi
35 bar
( span
psi) or ±0.0125 + 0.15 ( span bar) in % span
500 psi
35 bar
( span
psi) or ±0.15 + 0.15 ( span bar) in % span
±0.03% of URL per year
* Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
34-ST-03-65
Page 7
Performance Under Rated Conditions - General for all Models
Parameter
Description
Output (two-wire)
Analog 4 to 20 mA or DE digital communications mode. Options available for
FOUNDATION Fieldbus and HART protocol.
Supply Voltage Effect
0.005% span per volt.
Damping Time Constant
Adjustable from 0 to 32 seconds digital damping.
CE Conformity (Europe)
89/336/EEC, Electromagnetic Compatibility (EMC) Directive.
Lightning Protection Option
Leakage Current: 10 microamps max. @ 42.4 VDC, 93°C
(Code “LP”)
Impulse Rating:
(rise/decay)
10/20 µ sec.
5,000 Amps (50 strikes) 10,000 Amps (20 strikes)
10/1000 µ sec. 250 Amps (1000 strikes) 500 Amps (400 strikes)
Physical and Approval Bodies
Parameter
Description
Barrier Diaphragms Material
STD924, STD930
STD974
316L SS, Hastelloy C-276, Monel, Tantalum
316L SS, Hastelloy C-276
Process Head Material
STD924, STD930
STD974
316 SS, Carbon Steel (zinc-plated), Monel, Hastelloy
316 SS, Carbon Steel (zinc-plated), Hastelloy
Head Gaskets
Glass filled PTFE standard for STD924 & STD930 with Monel and Tantalum
diaphragm and STD974. Teflon standard otherwise. Viton optional.
Meter Body Bolting
Carbon Steel (Zinc plated) standard. Options include 316 SS, NACE A286 SS bolts
and 304 SS nuts and B7M.
Optional Adapter Flange and
Bolts
Adapter Flange materials include 316 SS, Hastelloy 276 and Monel. Standard adapter
flange gasket material is glass filled PTFE (STD924 & STD930 Monel and Tantalum
diaphragms, and STD974). Teflon standard otherwise. Viton is optional.
Mounting Bracket
Carbon Steel (Zinc-plated) or Stainless Steel angle bracket or Carbon Steel flat
bracket available (standard options).
Fill Fluid
Silicone DC 200 oil or CTFE (Chlorotrifluoroethylene)
Electronic Housing
Epoxy-Polyester hybrid paint. Low Copper-Aluminum. Meets NEMA 4X (watertight)
and NEMA 7 (explosionproof). Stainless steel optional.
Process Connections
1/4-inch NPT; 1/2-inch NPT with adapter, standard option; DIN.
Wiring
Accepts up to 16 AWG (1.5 mm diameter).
Mounting
Can be mounted in virtually any position using the standard mounting bracket. Bracket
is designed to mount on 2-inch (50 mm) vertical or horizontal pipe. See Figure 3.
Dimensions
See Figures 4 and 5.
Net Weight
Approximately 9 pounds (4.1 Kg)
Approval Bodies
Hazardous Areas
- Approved as explosion proof and intrinsically safe for use in Class I, Division 1,
Groups A, B, C, D locations, and nonincendive for Class I, Division 2, Groups A, B, C,
D locations. Approved EEx ia IIC T4, T5, T6 and EEx d IIC T5, T6 per ATEX
standards. See attached Model Selection Guide for options.
Canadian Registration
Number (CRN)
- All ST 3000 model designs, except STG19L, STG99L, STG170, STG180, have been
registered in all provinces and territories in Canada and are marked CRN: 0F8914.5C.
-
Pressure Equipment Directive
(97/23/EC)
The ST 3000 pressure transmitters listed in this Specification have no pressurized
internal volume or have a pressurized internal volume rated less than 1,000 bar
(14,500 psig) and/or have a maximum volume of less than 0.1 liter. Therefore, these
transmitters are either; not subject to the essential requirements of the directive
97/23/EC (PED, Annex 1) and shall not have the CE mark, or the manufacturer has
the free choice of a module when the CE mark is required for pressures > 200 bar
(2,900 psig).
NOTE: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or vessel(s) from
exceeding allowable pressure limits, (equipment with safety functions in accordance with Pressure Equipment Directive
97/23/EC article 1, 2.1.3), require separate examination.
34-ST-03-65
Page 8
Figure 3—Examples of typical mounting positions
34-ST-03-65
Page 9
Reference Dimensions:
With
Smart
meter
millimeters
inches
82.9
3.26
Removal
Clearance
for All Caps
45.7
1.8
94.9
3.74
53.1
2.09
65.1
2.56
Without
meter
Without
meter
3.6
0.14 Plug
135
5.32
55.3
2.18
23.5
.925
214
8.43
Optional
Meters
Optional
external
ground
125.2
4.93
Rotational
Lock
67
2.64
Optional Adapter
for 1/2-inch NPT
See Detail "A"
53.9
2.12
32.5
1.28
93.6
3.69
129
5.08
Detail A
53.9
2.12
High Pressure
Connection
1/2-inch NPT
Low Pressure
Connection
1/2-inch NPT
53.9
2.12
1.5
0.06
24258
Figure 4—Typical models STD924 and STD930-A, B, E, F, J (SS, Hastelloy C) mounting dimensions for
reference.
34-ST-03-65
Page 10
Reference Dimensions:
With Smart meter
millimeters
inches
82.9
3.26
94.9
3.74
53.1
2.09
Removal
Clearance 45.7
1.8
for All Caps
65.1
2.56
Without
meter
With
Analog
meter
3.6
135
5.32
Without
meter
0.14
55.3
2.18
Plug
Optional
meters
23.5
.925
Optional
external
ground
266.6
10.5
Rotational lock
168.8
6.65
85
3.35 SQ
Optional Adapter for
1/2-inch NPT
See Detail "A"
53.9
2.12
Plug
32.5
1.28
100
3.94
121.4
4.78
Detail A
53.9
2.12
High Pressure
Connection
1/2-inch NPT
Low Pressure
Connection
1/2-inch NPT
53.9
2.12
1.5
0.06
24259
Figure 5—Typical models STD924 and STD930-C, D, G, H, K, L (Monel, Tantalum), and model STD974
mounting dimensions for reference
34-ST-03-65
Page 11
Options
Mounting Bracket
The angle mounting bracket is
available in either zinc-plated
carbon steel or stainless steel and
is suitable for horizontal or vertical
mounting on a two inch (50
millimeter) pipe, as well as wall
mounting. An optional flat
mounting bracket is also available
in carbon steel for two inch (50
millimeter) pipe mounting.
Indicating Meter
(ME and SM Options)
Two integral meter options are
available. An analog meter (option
ME) is available with a 0 to 100%
linear scale. The Smart Meter
(option SM) provides an LCD
display for both analog and digital
output and can be configured to
display pressure in pre-selected
engineering units.
Lightning Protection
(Option LP)
A terminal block is available with
circuitry that protects the
transmitter from transient surges
induced by nearby lightning
strikes.
HART Protocol Compatibility
(Option HC)
An optional electronics module is
available for the ST 3000 that
provides HART Protocol
compatibility. Transmitters with the
HART Option are compatible with
the AMS System. (Contact your
AMS Supplier if an upgrade is
required.)
Indicator Configuration
(Option CI)
Provides custom configuration of
Smart Meters.
Tagging (Option TG)
Ordering Information
Contact your nearest Honeywell sales
office, or
In the U.S.:
Honeywell
Industrial Automation & Control
16404 North Black Canyon Hwy.
Phoenix, AZ 85053
1-800-288-7491
Up to 30 characters can be added
on the stainless steel nameplate
mounted on the transmitter’s
In Canada:
electronics housing at no extra cost.
The Honeywell Centre
Note that a separate nameplate on
155 Gordon Baker Rd.
the meter body contains the serial
North York, Ontario M2H 3N7
number and body-related data. A
1-800-461-0013
stainless steel wired on tag with
additional data of up to 4 lines of 28 In Latin America:
Honeywell Inc.
characters is also available. The
480 Sawgrass Corporate Parkway,
number of characters for tagging
Suite 200
includes spaces.
Sunrise, FL 33325
Transmitter Configuration
(Option TC)
The factory can configure the
transmitter linear/square root
extraction, damping time, LRV,
URV and mode (analog/digital) and
enter an ID tag of up to eight
characters and scratchpad
information as specified.
Custom Calibration and ID in
Memory (Option CC)
The factory can calibrate any range
within the scope of the transmitter’s
range and enter an ID tag of up to
eight characters in the transmitter’s
memory.
FOUNDATION Fieldbus
(Option FF)
Equips transmitter with FF
protocol for use in 31.25 kbit/s
FF networks. See document
34-ST-03-72 for additional
information on ST 3000
Fieldbus transmitters.
(954) 845-2600
In Europe and Africa:
Honeywell S. A.
Avenue du Bourget 1
1140 Brussels, Belgium
In Eastern Europe:
Honeywell Praha,
s.r.o. Budejovicka 1
140 21 Prague 4,
Czech Republic
In the Middle East:
Honeywell Middle East Ltd.
Khalifa Street,
Sheikh Faisal Building
Abu Dhabi, U. A. E.
In Asia:
Honeywell Asia Pacific Inc.
Honeywell Building,
17 Changi Business Park Central 1
Singapore 486073
Republic of Singapore
In the Pacific:
Honeywell Pty Ltd.
5 Thomas Holt Drive
North Ryde NSW Australia 2113
(61 2) 9353 7000
In Japan:
Honeywell K.K.
14-6 Shibaura 1-chrome
Minato-ku, Tokyo, Japan 105-0023
Specifications are subject to change without notice.
(Note that specifications may differ slightly for transmitters manufactured before
October 30, 1995.)
Or, visit Honeywell on the World Wide
Web at: http://www.honeywell.com
34-ST-03-65
Page 12
Issue 31
Instructions
Select the desired Key Number. The arrow to the right marks the selection available.
Make one selection from each table, I and II, using the column below the proper arrow.
Select as many Table III options as desired (if no options or approvals are desired, specify 9X).
A (Š) denotes unrestricted availability. A letter denotes restricted availability.
Restrictions follow Table IV.
Key Number
______
I
-
___
II
-
_____
III (Optional)
-
_ _, _ _, _ _
KEY NUMBER
IV
+
XXXX
Selection
Span
0-10" to 0-400" H2O/0-25 to 0-1000 mbar
Body Rating: 3000 psi (210 bar)
0-5 to 0-100 psi/0-0.34 to 0-7 bar
Body Rating: 3000 psi (210 bar)
0-100 to 0-3000 psi/0-7 to 0-210 bar
Body Rating: 4500 psi (315 bar)
Availability
STD924
STD930
STD974
TABLE I - METER BODY
Wetted
Process Heads
Material
of
Construction
Carbon Steel *
Carbon Steel *
Carbon Steel *
Carbon Steel *
316 SS
316 SS
316 SS
316 SS
Hastelloy C
Hastelloy C
Monel
Vent/Drain
Valves **
and Plugs
316 SS
316 SS
316 SS
316 SS
316 SS
316 SS
316 SS
316 SS
Hastelloy C
Hastelloy C
Monel
Barrier
Diaphragms
316L SS
Hastelloy C
Monel
Tantalum
316L SS
Hastelloy C
Monel
Tantalum
Hastelloy C
Tantalum
Monel
Fill Fluid
Silicone
CTFE
Process Head
Configuration
1/4" NPT
1/2" NPT with Adapter (on 1/4" NPT Head)
TABLE II
No Selection
* Carbon Steel heads are zinc-plated.
** Vent/Drains are Teflon coated for lubricity.
A__
B__
C__
D__
E__
F__
G__
H__
J__
K__
L__
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
_1_
_2_
Š Š Š
Š Š Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
__A
__H
Š Š Š
00000
Š Š Š
t
Not recommended for water service due to hydrogen migration.
Use Stainless Steel heads.
t
t
34-ST-03-65
Page 13
Issue 31
Availability
STD9
TABLE III - OPTIONS
None
Communication Protocols
®
HART Protocol Compatible Electronics
FOUNDATION Fieldbus Communications
Selection
00
24 30 74
Š Š Š
HC
FF
e
r
e
r
b
ME
SM
CI
LZ
ZS
Š Š Š
Š Š Š
b
e
r
Indicating Meter Options
Analog Meter (0-100 Even 0-10 Square Root)
Smart Meter
Custom Configuration of Smart Meter
Local Zero
Local Zero and Span
m m m
x x x
s s s
b
Transmitter Housing & Electronics Options
Lightning Protection
Custom Calibration and I.D. in Memory
Transmitter Configuration
Write Protection
316 SS Electronics Housing - with M20 Conduit Connections
1/2" NPT to M20 316 SS Conduit Adapter (BASEEFA EEx d IIC)
1/2" NPT to 3/4" NPT 316 SS Conduit Adapter
Stainless Steel Housing with M20 to 1/2" NPT 316 SS Conduit
Adapter (use for FM and CSA Approvals)
Stainless Steel Customer Wired-On Tag
(4 lines, 28 characters per line, customer supplied information)
Stainless Steel Customer Wired-On Tag (blank)
Low Temperature - -50oC Ambient Limit
End Cap Live Circuit Warning Label in Spanish (only with ATEX 3D)
End Cap Live Circuit Warning Label in Portuguese (only with ATEX 3D)
End Cap Live Circuit Warning Label in Italian (only with ATEX 3D)
End Cap Live Circuit Warning Label in German (only with ATEX 3D)
LP
CC
TC
WP
SH
A1
A2
A3
Š
Š
Š
Š
TG
Š Š Š
TB
LT
SP
PG
TL
GE
Š Š Š
Š
SS
B7
CR
S2
S3
S4
S5
T2
T3
V2
V3
B3
B4
B5
B6
SV
CV
B2
DN
VT
VF
Š Š Š
k k Š
Š Š Š
d
w
z
k
MB
SB
FB
Š Š Š
Š Š Š
Š Š Š
UM
0X
TP
F1
F3
Š Š Š
Š
Š
Š
Š
Š
Š
Š
Š
n n n
n n n
i i i
i i i
a
a
a
a
a
a
a
a
a
a
a
a
b
b
Meter Body Options
316 SS Bolts and 316 SS Nuts for Process Heads
B7M Bolts and Nuts for Process Heads
NACE A286 SS Bolts and 304 SS Nuts for Process Heads
316 SS Adapter Flange - 1/2" NPT with CS Bolts
316 SS Adapter Flange - 1/2" NPT with 316 SS Bolts
316 SS Adapter Flange - 1/2" NPT with NACE A286 SS Bolts
316 SS Adapter Flange - 1/2" NPT with B7M Bolts
Hastelloy C Adapter Flange - 1/2" NPT with CS Bolts
Hastelloy C Adapter Flange - 1/2" NPT with 316 SS Bolts
Monel Adapter Flange - 1/2" NPT with CS Bolts
Monel Adapter Flange - 1/2" NPT with 316 SS Bolts
316 SS Blind Adapter Flange with CS Bolts
316 SS Blind Adapter Flange with 316 SS Bolts
316 SS Blind Adapter Flange with NACE A286 SS Bolts
316 SS Blind Adapter Flange with B7M Bolts
Side Vent/Drain (End Vent Drain is standard)
SS Center Vent Drain and Bushing
Blind DIN SS Flanges Mounted with NACE Bolts
Modified DIN Process Heads - 316 SS
Viton Process Head Gaskets (adapter gaskets ordered separately)
Viton Adapter Flange Gaskets
c
c
c
k
k
c
k
k
c
k
c
k
k
k
k
k
k
k
c
k
c
k
k
k
k
k
c
c
c
c
c
c
c
c
c
c
b
b
b
Š Š Š
Š Š
d
w
z Š
k Š
Transmitter Mounting Brackets Options
Mounting Bracket - Carbon Steel
Mounting Bracket - SS
Flat Mounting Bracket - Carbon Steel
b
Services/Certificates/Marine Type Approvals Options
User's Manual Paper Copy (Standard, HC, or FF ships accordingly)
Clean Transmitter for Oxygen or Chlorine Service with Certificate
Over-Pressure Leak Test with F3392 Certificate
Calibration Test Report and Certificate of Conformance (F3399)
Certificate of Conformance (F3391)
j
j
j
Š Š Š
Š Š Š
Š Š Š
Table III continued next page
b
34-ST-03-65
Page 14
Issue 31
Availability
STD9
TABLE III - OPTIONS (continued)
Certificate of Origin (F0195)
FMEDA (SIL) Certificate
NACE Certificate (F0198)
Marine Type Approvals (DNV, ABS, BV & LR)
Selection
F5
F6
F7
MT
24 30 74
Š Š Š
Š Š Š
o o o
2 2 2
Warranty Options
Additional Warranty - 1 year
Additional Warranty - 2 years
Additional Warranty - 3 years
Additional Warranty - 4 years
Approval
Body
Approval Type
No hazardous location approvals
Explosion Proof
Factory
Dust Ignition Proof
Mutual
Non-Incendive
Intrinsically Safe
CSA
SA
(Australia)
ATEX*
INMETRO
(Brazil)
Explosion Proof
Dust Ignition Proof
Intrinsically Safe
Intrinsically Safe
Non-Sparking
Intrinsically Safe,
Zone 0/1
Flameproof, Zone 1
W1
W2
W3
W4
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
9X
Š Š Š
1C
Š Š Š
2J
Š Š Š
Location or Classification
Class I, Div. 1, Groups A,B,C,D
Class II, III Div. 1, Groups E,F,G
Class I, Div. 2, Groups A,B,C,D
Class I, II, III, Div. 1, Groups
A,B,C,D,E,F,G
Class I, Div. 1, Groups B,C,D
Class II, III, Div. 1, Groups E,F,G
Class I, II, III, Div. 1, Groups
A,B,C,D,E,F,G
Ex ia IIC T4
Ex n IIC T6 (T4 with SM option)
Ex II 1G
EEx ia IIC T4, T5,T6
Ex II 2G
EEx d IIC T5, T6,
Enclosure IP 66/67
Non-Sparking, Zone 2 Ex II 3G
EEx nA, IIC T6
(Honeywell). Enclosure IP 66/67
Multiple Marking**
Ex II 1 G EEx ia IIC T4, T5, T6
Int. Safe, Zone 0/1, or
Ex II 2 G EEx d IIC T5, T6
Flameproof, Zone 1, or
Ex II 3 G EEx nA, IIC T6 (Honeywell)
Non-Sparking, Zone 2
Enclosure IP 66/67
Flameproof, Zone 1
Ex d IIC T5
b
4G
Š Š Š
3S
Š Š Š
3D
Š Š Š
3N
Š Š Š
3H
Š Š Š
6D
Š Š Š
*See ATEX installation requirements in the ST 3000 User's Manual
**The user must determine the type of protection required for installation of the equipment. The user shall then
check the box [D] adjacent to the type of protection used on the equipment certification nameplate. Once a type
of protection has been check
TABLE IV
Factory Identification
b
XXXX
Š Š Š
34-ST-03-65
Page 15
Issue 31
RESTRICTIONS
Restriction
Letter
a
b
c
d
Table
III
I
I
III
Available Only With
Selection
Table
3D or 3H
Select only one option from this group
__H
Not Available With
Selection
E _ _, F _ _
DN
e
III
4G
g
I
I
K _ _, L _ _
includes side vent
no price add
C _ _, G _ _, L _ _
III
1C, 2J
III
III
TC, ME, 4G,3S
FF, ME
III
SV
I
J_ _, includes
side vent, no price add
DN
B _ _, F _ _, J _ _,
FB
h
i
III
j
k
m
n
o
r
s
t
I
I
III
C_H, D_H, G_H, H_H, K_H, L_H
SM
III
CR,S4,B5
III
III
w
I
x
y
III
z
2
Note:
1C or 2J
_2_
Select from Table III S2,S3,S4
S5,T2,T3,V2,V3,B3,B4,B5,B6
E _ A, F _ A
FF, SM
III
I
III
See ST-83 for Published Specials with pricing.
See ST-89 and User's Manual for part numbers.
See ST-OE-9 for OMS Order Entry Information including TC, manuals,
certificates, drawings and SPINS.
See ST-OD-1 for tagging, ID, Transmitter Configuration (TC) and
calibration including factory default values.
To request a quotation for a non-published "special", fax RFQ to Marketing
Applications.
34-ST-03-65
Page 16
This page intentionally blank
ST 3000 is a registered trademark of Honeywell International Inc.
HART* is a trademark of the Hart Communication Foundation.
FOUNDATION™ is a trademark of the Fieldbus Foundation.
Industrial Measurement and Control
Honeywell International Inc.
2500 W. Union Hill Drive
Phoenix, Arizona 85027
Honeywell International Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement