User Manual
INSTRUCTION MANUAL
CORDED HAMMER DRILL
WITH 50-PIECE ACCESSORY KIT
054-3179-0
Read and understand this instruction manual
thoroughly before using the product. It contains
important information for your safety as well as
operating and maintenance advice.
TECHNICAL SPECIFICATIONS 3
SAFETY GUIDELINES 4–8
DESCRIPTION9
OPERATING INSTRUCTIONS 10–15
MAINTENANCE 16–17
TROUBLESHOOTING 18
PARTS LIST 19–20
WARRANTY 21–22
Keep this instruction manual for future use. Should
this product be passed on to a third party, then this
instruction manual must be included.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
TABLE OF CONTENTS
If any parts are
missing or damaged,
or if you have any
questions, please call
our toll-free helpline
at 1-800-689-9928.
2
WARNING!
RATING POWER
6A
RATING
120V, 60 Hz ~
NO-LOAD SPEED
0–2700 RPM
Safety symbols in this Instruction Manual are used to flag possible dangers. The safety
symbols and their explanations require your full understanding. The safety warnings do
not, by themselves, eliminate any danger, nor are they substitutes for proper accident
prevention measures.
HAMMER SPEED
0–43,200 BPM
WARNING!
KEYED CHUCK
1/2” (13 mm)
MAXIMUM DRILLING CAPACITY
IN WOOD
IN METAL
IN CONCRETE
1" (25.4 mm)
1/2" (13 mm)
1/2" (13 mm)
TOOL WEIGHT
4 lb 14 oz (2.2 kg)
This Safety Alert Symbol indicates caution, warning, or danger. Failure to obey a safety
warning can result in serious injury to yourself or others. To reduce the risk of injury, fire, or
electric shock, always follow the safety precautions.
Know your tool
To operate this tool, carefully read this Instruction Manual and all labels affixed to the hammer drill
before using. Keep this manual available for future reference.
Important
This tool should only be serviced by a qualified service technician. For more information, call the
toll-free helpline at 1-800-689-9928.
Read all instructions thoroughly
Save these instructions
General power tool safety warnings
WARNING!
Read all safety warnings and instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
4
SAFeTY GUIDELINES
TECHNICAL SPECIFICATIONS
3
Work area safety
SAFETY GUIDELINES
• Keep the work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks, which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
Electrical safety
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a ground-fault circuit
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
Personal safety
• Stay alert, watch what you are doing and use common sense when operating a power tool.
Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection, used for appropriate conditions,
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting
to power source and/or battery pack, picking up or carrying the tool. Carrying power tools
with your finger on the switch or energising power tools that have the switch on invites accidents.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of
the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure
that these are connected and properly used. Use of these devices can reduce dust-related hazards.
Power tool use and care
• Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and more safely at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories, tool bits, etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
Service
• Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
6
SAFETY GUIDELINES
5
8
Safety guidelines for hammer drill
Contents:
• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
Hammer drill, chuck key, auxiliary handle, depth-stop gauge and instruction manual.
• Use the auxiliary handles, if supplied with the tool. Loss of control can cause personal injury.
50-piece accessory kit:
• Hold the power tool by the insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a “live”
wire may make exposed metal parts of the power tool “live” and could give the operator an electric
shock.
• 8 pcs HSS drill bits: 5/64", 3/32", 7/64", 1/8", 9/64", 5/32", 3/16", 1/4"
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
• 4 pcs nut drivers: 3/16", 1/4", 5/16", 3/8"
V ..................... Volts
A ..................... Amperes
Hz ................... Hertz
W .................... Watts
min ................. Minutes
............... Alternating current
............. Direct current
n0 ................... No-load speed
............... Class II Construction
…/min ........... Revolutions per minute
• 6 pcs masonry drill bits: 1/8", 5/32", 3/16", 7/32", 1/4", 5/16"
• 6 pcs wood-boring bradpoint drill bits: 1/8", 5/32", 3/16", 1/4", 9/32", 5/16"
• 18 pcs screwdriver bits (1"):
Hex: 3/32", 1/8", 5/32", 3/16", 1/4"
Slotted: 3-4, 6-8, 8-10, 10-12
PH1, PH2(x4), PH3
S1, S2, S3
• 7 pcs screwdriver bits (2"):
Slotted: 6-8, 8-10
PH2, PH3
S1, S2, S3
• 1pc screw guide: 76mm X dia 11.5mm
WARNING!
Remove the hammer drill from the package and examine it carefully. Do not discard the
carton or any packaging material until all parts have been examined.
............... Grounding terminal
BPM ............... Beats per minute
.............. WARNING – To reduce the risk of injury, user must read instruction manual.
• Use clamps or another practical way to support the workpiece and secure it to a stable
platform. Holding the workpiece by hand or against your body is unstable and may lead to loss of
control.
• Inspect the tool cords periodically and, if damaged, have them repaired by a qualified
repair person. Constantly stay aware of the cord location. Following this rule will reduce the risk of
electric shock or fire.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
SAFETY GUIDELINES
SAFETY GUIDELINES
7
Know your tool
WARNING!
DESCRIPTION
5
6
2
1
3
4
Never connect the hammer drill to the power source when you are assembling parts,
making adjustments, installing or removing bits, cleaning, or when it is not in use.
Disconnecting the hammer drill will prevent accidental starting, which could cause serious
personal injury.
14
Variable-speed trigger switch
(fig 1)
7
1. Connect the power cord of your hammer drill
to a standard household power outlet.
2. To turn the hammer drill ON, press the trigger
switch.
13
12
11
fig 1
Variable-speed
trigger switch
3. To turn the hammer drill OFF, release the
trigger switch.
10
9
8
No.
Description
1
Chuck jaws
2Chuck
3
Chuck-key holes
4
Chuck sleeve
5
Hammer/drilling selection switch
6
Depth-stop gauge
7
Lock-on button
10
No.
Description
8
Chuck key
9Chuck-key strap
10
Variable-speed trigger switch
11
Speed adjustment dial
12
Direction-of-rotation lever
13
Auxiliary handle
14
Primary handle
Before attempting to use this tool, become familiar with all of its operating features and safety
requirements. For optimum performance and safety, read the following operating instructions carefully
before using.
4. The variable-speed trigger switch delivers
higher speed with increased trigger pressure and lower speed with decreased trigger pressure.
Lock-on button (fig 2)
This hammer drill is equipped with a lock-on
button, which is convenient for continuous drilling
for extended periods of time.
1. To drill continuously, press and hold the trigger
switch and then press the lock-on button.
Release the trigger switch.
fig 2
Lock-on button
2. To unlock the lock-on button and stop
continuous drilling, press the trigger
switch and the lock-on button will release
automatically.
WARNING!
Do not allow familiarity with the hammer drill to cause a lack of alertness. A fraction of a
second of carelessness is enough to cause severe injury.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
OPERATING INSTRUCTIONS
9
Speed adjustment dial (fig 3)
This hammer drill is equipped with a speed
adjustment dial; the required speed may be
adjusted according to the material and the
working conditions.
Auxiliary handle (fig 5)
fig 3
The tool must be supported with the auxiliary
handle, which can be swiveled and locked into any
of 12 positions, 360° around the collar mount.
Variablespeed dial
1. Unplug the hammer drill from the power
source.
For working at low speed, turn the dial
counterclockwise to the “–” position .
Locking
teeth
x
Auxiliary handle
2. Rotate the lower portion of auxiliary handle
counter-clockwise.
For working at high speed, turn the dial clockwise to the “+” position.
The direction of bit rotation is reversible and is
controlled by a selector located above the trigger
switch. With the drill held toward you:
fig 5
To reposition and/or swivel the handle,
The speed adjustment dial can be adjusted even if
the drill is running.
Direction-of-rotation selector
(fig 4)
12
Clockwise
Counter-clockwise
3. Push the handle forward until it disengages from the locking teeth in the collar mount.
4. Move the handle to the desired position.
fig 4
Reverse
1. Position the direction-of-rotation selector to
the right of the tool for forward rotation.
5. Push the handle inward until it engages in the desired position.
Forward
Direction-ofrotation selector
2. Position the direction-of-rotation selector to
the left of the tool for reverse rotation.
6. Securely tighten the auxiliary handle by rotating it clockwise.
Depth-stop gauge (fig 5)
Your drilling depth can be pre-set and/or repeated by using the depth-stop gauge. Setting depth:
Install the auxiliary handle and make sure the accessory has been fully inserted into the chuck before
setting the depth-stop gauge (fig 5).
To adjust the depth:
WARNING!
1. Unplug the hammer drill from the power source.
To prevent gear damage, always allow the hammer drill to come to a complete stop before
changing the direction of rotation.
2. Rotate the lower portion of auxiliary handle counter-clockwise to loosen the depth-stop gauge.
3. Slide depth-stop gauge to the desired position
4. Securely tighten the auxiliary handle by rotating it clockwise.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
11
Installing bits (fig 6)
OPERATING INSTRUCTIONS
1. Unplug the hammer drill from the power source.
fig 6
2. Open the chuck jaws by turning the sleeve in
a counterclockwise direction until the opening
is slightly larger than the bit you intend to use,
and raise the front of the drill slightly to keep
the bit from falling out of the chuck jaws.
Hammer/drilling selection
switch (fig 8 )
14
fig 8
When drilling in concrete, granite, tile, marble,
etc., push the selection switch to the side marked
with this symbol:
.
To select drilling mode for drilling in wood and
metal, push the selection switch to the side
marked with this symbol:
.
3. Insert the drill bit into the chuck.
4. Tighten the sleeve by hand.
5. Place the chuck key in one of the three chuck key holes and tighten in clockwise direction. Repeat
with the remaining two chuck key holes.
Drilling
WARNING!
1. Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit
rotates.
It is important to tighten the chuck with all three key holes to prevent slippage.
2. Unplug the hammer drill from the power source.
3. Install the auxiliary handle and the correct bit.
6. Remove the chuck key.
4. Connect the hammer drill to the power source
WARNING!
5. Verify that the direction-of-rotation selector is at the correct setting (forward).
Insert the drill bit straight into the chuck jaws. Inserting the drill bit into the chuck jaws at an
angle and then tightening the chuck and using the drill could cause the drill bit to be thrown
from the hammer drill, resulting in possible serious personal injury or damage to the chuck.
Removing bits (fig 7)
WARNING!
6. Hold the hammer drill firmly with one hand on the primary handle and the other hand on the
auxiliary handle
7. Place the bit at the point to be drilled.
8. Press the trigger switch to start the hammer drill.
fig 7
Use protective gloves when removing
the bit from the tool, or allow the bit
to cool down first. The bit may be hot
after prolonged use.
1. Unplug the hammer drill from the power source.
2. Place the chuck key in one of the three chuck
key holes and loosen the chuck by turning in a
counterclockwise direction.
9. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not
force the hammer drill or apply side pressure to elongate a hole. Allow the tool to do the work.
10.When drilling hard, smooth surfaces, use a centre punch to mark the desired location of the hole.
This will prevent the drill bit from slipping off-centre as the hole is started.
11.When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the
life of the bit and increase the drilling action.
12.If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Reverse the direction
of rotation and gently squeeze the trigger switch to remove the bit from the workpiece. Investigate
and correct the cause of jamming before you resume work.
3. Remove the chuck key.
4. Loosen the sleeve by hand.
5. Remove the drill bit.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
OPERATING INSTRUCTIONS
13
Drilling in wood
Before each use
For maximum performance, use high-speed steel or brad-point bits for wood drilling.
1. Inspect the hammer drill, the trigger switch, the cord and the accessories for damage.
1. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
2. Check for damaged, missing, or worn parts.
2. Increase the speed as the drill bit enters the material.
3. Check for loose screws, misalignment or binding of moving parts, or any other condition that may
affect the operation.
3. When drilling holes all the way through the workpiece, place a block of wood behind the workpiece
to prevent ragged or splintered edges on the back side of the hole.
Drilling in metal
For maximum performance, use high-speed steel bits for metal or steel drilling.
1. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the
life of the bit and increase the drilling action.
2. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
3. Maintain a speed and pressure that allows cutting without overheating the bit. Applying too much
pressure will:
• Overheat the hammer drill
• Wear the bearings
4. If abnormal vibration or noise occurs, turn the tool off immediately and have the problem
corrected before further use. Unplug the tool from power source before cleaning or performing
any maintenance. Using compressed air may be the most effective cleaning method. Always wear
safety goggles when cleaning tools using compressed air.
WARNING!
Do not allow brake fluids, gasoline and petroleum-based products, penetrating oil, etc.
to come into contact with plastic parts. These substances contain chemicals that can
damage, weaken, or destroy plastic.
WARNING!
When servicing, use only identical replacement parts. The use of any other parts may
create a hazard or cause damage to the product.
• Bend or burn the bits
WARNING!
• Produce off-centre or irregularly-shaped holes
If the supply cord of this power tool is damaged, it must be replaced by a specially
prepared cord available through the service organization.
Drilling in masonry
WARNING!
For maximum performance, use carbide-tipped masonry bits when drilling holes in brick, tile, concrete, etc.
Use only accessories that are recommended for this hammer drill by the manufacturer.
Accessories that may be suitable for one tool may become hazardous when used with
another tool.
1. Maintain a speed and pressure which allows cutting without overheating the bit or drill. Applying
too much pressure will:
• Overheat the hammer drill
WARNING!
• Wear the bearings
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools
with sharp cutting edges are less likely to bind, and are easier to control.
• Bend or burn bits
• Produce off-centre or irregular-shaped holes
2. Apply light pressure and medium speed for best results in brick.
3. Apply additional pressure for hard materials such as concrete.
WARNING!
To ensure safety and reliability, all repairs should be performed by a qualified service
technician.
4. When drilling holes in tile, practice on a scrap piece to determine the best speed and pressure.
Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
16
MAINTENANCE
OPERATING INSTRUCTIONS
15
Removing the chuck (fig 9)
1. Unplug the hammer drill from the power
source.
18
fig 9
Chuck jaws
2. Open the chuck jaws by turning the sleeve in
a counter-clockwise direction.
3. Use a Phillips screwdriver (not included) to
remove the chuck screw by turning it in a
clockwise direction.
PROBLEM
Mallet
Hex wrench
4. Insert a 5/16 in. or larger hex key (not
included) into the chuck and securely tighten the chuck jaws around the hex key.
POSSIBLE CAUSES
SOLUTIONS
The motor does not start
The tool is not connected to a power
source
Connect the tool to a power
source
The bit cannot be installed
1. The sleeve is not released
2. The bit does not fit the chuck jaw
1. Release the sleeve
2. Use the appropriate bit
The motor is overheating
Cooling vents are obstructed
Clean and clear vents. Do not
cover with hand during operation
If the problem remains unsolved after performing the checks described above, call the tollfree helpline at 1-800-689-9928.
5. Tap the hex key sharply with a mallet (not included) in a counter-clockwise direction. This will
loosen the chuck for easy removal.
NOTICE: The chuck screw has left-handed threads. Attach a new chuck to the spindle and tighten the
chuck screw.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
TROUBLESHOOTING
MAINTENANCE
17
No. Part No.
Description
No. Part No.
Description
1 543179001
Screw
21 543179021
Copper Brush Holder
2 543179002
Chuck
22 543179022
Brush Holder Box
3
543179003Output Shaft
23
543179023Stator
4 543179004
Steel Ball
24 543179024
Ball Bearing
5
543179005Spring
25
543179025Bearing sleeve
6
543179006Ball Bearing
26
543179026Switch
7
543179007Circlip
27
543179027Wire (white)
8
543179008Gear
28
543179028Wire (black)
9 543179009
Washer
29 543179029
Cable Pressing Board
10543179010 Retaining Ring
30543179030 Screw
11 543179011
Oil Bearing
31 543179031
Cable Jacket
12 543179012
Bracket
32 543179032
Cable & Plug
13 543179013
Sealing Ring
33 543179033
Right Housing
14543179014 Ball Bearing
34543179034 Screw
15543179015 Rotor
35543179035 Handle
16 543179016
Change Piece
36 543179036
Handle Support
17 543179017
Impact Button
37 543179037
Depth Gauge
18 543179018
Left Housing
38 543179038
Pressure plate
19 543179019
Brush Holder Box Cover
39 543179039
Hex Bolt
20 543179020
Carbon Brush
If the problem remains unsolved after performing the checks described above, call the tollfree helpline at 1-800-689-9928.
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
20
PARTS LIST
Exploded view
PARTS LIST
19
f) this warranty will not apply to any product that was sold to the original purchaser as a
reconditioned or refurbished product (unless otherwise specified in writing);
22
g) this warranty will not apply to any product or part thereof if any part from another manufacturer
is installed therein or any repairs or alterations have been made or attempted by unauthorized
persons;
h) this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited
to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical
cleaners; and
i) this warranty will not apply to component parts sold by and identified as the product of another
company, which shall be covered under the product manufacturer’s warranty, if any.
This Mastercraft product is guaranteed three (3) years from the date of original retail purchase
against defects in materials and workmanship, except for the following components:
a)Component A: Batteries, chargers and carrying case, which are guaranteed for a period of 2 years
from the date of original retail purchase against defects in workmanship and materials;
b)Component B: Accessories, which are guaranteed for a period of 1-year from the date of original
retail purchase against defects in workmanship and materials.
Subject to the conditions and limitations described below, this product, if returned to us with proof
of purchase within the stated warranty period and if covered under this warranty, will be repaired or
replaced (with the same model, or one of equal value or specification), at our option. We will bear the
cost of any repair or replacement and any costs of labour relating thereto.
Additional limitations
This warranty applies only to the original purchaser and may not be transferred. Neither the retailer
nor the manufacturer shall be liable for any other expense, loss or damage, including, without
limitation, any indirect, incidental, consequential or exemplary damages arising in connection with the
sale, use or inability to use this product.
Notice to consumer
This warranty gives you specific legal rights, and you may have other rights, which may vary from province to
province. The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim
or exclude any statutory warranties set forth in any applicable provincial or federal legislation.
These warranties are subject to the following conditions and
limitations:
a) a bill of sale verifying the purchase and purchase date must be provided;
b) this warranty will not apply to any product or part thereof which is worn or broken or which has
become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation,
operation or maintenance (as outlined in the applicable owner’s manual or operating instructions)
or which is being used for industrial, professional, commercial or rental purposes;
c) this warranty will not apply to normal wear and tear or to expendable parts or accessories that
may be supplied with the product which are expected to become inoperative or unusable after a
reasonable period of use;
d) this warranty will not apply to routine maintenance and consumable items such as, but not limited
to, fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments;
e) this warranty will not apply where damage is caused by repairs made or attempted by others (i.e.
persons not authorized by the manufacturer);
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT - 054-3179-0
WARRANTY
WARRANTY
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising