Toyota RS3000 Alarm Installation Instructions

Toyota RS3000 Alarm Installation Instructions
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section I − Installation Preparation
Part Number: 08586−3D841
Section I − Installation Preparation
Kit Contents
Quantity Reqd.
1
1
1
2
1
Color Applicability/Trim Level
Description
Wire Harness
Status Monitor
Piezo Buzzer
Butyl Tape Pad
Extra Large Wire Tie
Accessory
Color
Item #
1
2
3
4
5
Vehicle/Trim Color
Hardware Bag Contents
Item #
1
2
3
4
5
Quantity Reqd.
2
2
10
10
x
x
Description
Foam Tape Strip (2 pcs.)
Small Foam Tape Strip
Large Wire Ties
Medium Wire Ties
x
x
x
x
x
x
x
x
Additional Items Required For Installation
Item #
1
2
Quantity Reqd.
1
Description
V3 Base Kit (08585−00921)
2001− Tacoma
Recommended Sequence of Application
Item #
1
2
3
Conflicts
Note: Must only be installed in vehicles with power door locks,
Note: and without factory keyless entry system.
Note:
Recommended Tools
Safety Tools
Safety Glasses
Safety Gloves
Vehicle Protection
General Applicability
*Mandatory
Legend
STOP
(Optional)
Blankets, Part Boxes
Special Tools
Installation Tools
Phillips Head Screwdriver
Small, Flat Blade Screwdriver
10 mm Socket
Pneumatic/Electric Wrench
Torque Wrench
Nylon Panel Removal Tool
Side Cutters
Accessory
Audio
V3
#2, screwdriver or tip
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CRITICAL PROCESS: Proceed with caution to
ensure a quality installation. These points will be
audited on a completed vehicle installation.
GENERAL PROCESS: This highlights specific
processes to ensure a quality installation. These
points will be audited during the accessory
installation.
TOOLS & EQUIPMENT: This calls out the specific
tools and equipment required for this process.
Special Chemicals
Windex
3M Prep Solvent−70
Rev.: C: 10/02/00
Page 1 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
Section II − Installation Procedure
A. Vehicle Disassembly
10mm Soc k et
1. Disconnect the negative battery cable.
(Fig. A1)
i.
Negative
batter y
Cabl e
Batter y
Cover the fender before starting.
ii. Be careful to not touch the positive
battery terminal.
Fig. A1
2. Remove the driverÕ
s step cover. (Fig. A2)
Scr ewdr iver
Scre ws ( x4 )
i.
Protect the seat and floor before
starting.
ii. Remove the four serews securing the
cover.
iii. Do not scratch the cover.
Step Cover
Fig. A2
3. Remove the driverÕ
s cowl cover. (Fig. A3)
i.
Do not scratch the cover.
Cowl Cover
Fig. A3
4. Remove the hood release lever. (Fig. A4)
i.
Remove the two screws securing the
lever to the lower dash cover.
Scr ewdr iver , 10mm Socket
Bol ts( x3) )
ii. Remove the cable from the lever.
Sc r ew
5. Remove the lower dash cover. (Fig. A4)
i.
Remove the four bolts and one screw
securing the cover.
ii. Do not scratch the cover.
Rev.: C 10/02/00
Bol t
Page 2 of 22 Pages
Lower Das h
Cov er
Scre ws ( x2 )
Fig. A4
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
6. Loosen the vehicleÕ
s wire harness, if so
equipped.
(Fig. A5)
i.
Cl ip
Unfasten the clips securing the
harness.
Vehicl e
Har ness
Cl ip ( x2)
Fig. A5
7. Remove the middle heater duct. (Fig. A6)
i.
Scr ewdr iver
Sc r ew
Remove the screw securing the heater
ductÕ
s bracket to the vehicle.
Heater Duct
Fig. A6
8. Prepare a protective sheet, then place
protective sheet over the front edge of the
center console.
(Fig. A7)
Pr otective
Sheet
Fig. A7
Rev.: C: 10/02/00
Page 3 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
9. Loosen the bracket cover, but do not
remove the cover. (Fig. A8)
i.
Cl ip
Remove the two clips securing the
bracket cover.
ii. Do not scratch the cover.
Cl ip
iii. Do not bend the cover.
Br acket Cover
Fig. A8
10 mm Socket,
Socket Extension
B. Piezo Buzzer Installation
R/ B No. 2
1. Remove and save the three bolts securing
R/B No. 2 to the body in the engine
room. (Fig. B1)
Bol t
( Existing)
Bol t
( Existing)
Fig. B1
2. Locate the vehicle harnessÕgray 2P
connector, then remove and discard the
black cap. (Fig. B2)
i.
R/ B No. 2
Vehicl e Har nessÕ
2P ( Gr ay)
Pr otective Cap
Locate the 2P connector between
R/B No. 2 and the body.
ii. Pull the connector toward the battery
to remove the cap and make the
connection.
Fig. B2
Rev.: C: 10/02/00
Page 4 of 23 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
3. Connect the Piezo BuzzerÕ
s gray 2P
connector to the vehicle harnessÕ 2Pgray
connector. (Fig. B3)
i.
Verify the connectors are plugged in
securely.
Side Cutter s
Piezo
Buz zer
Lar ge Wir e
Tie ( x2)
Vehicl e
Har nessÕ
2P
4. Using a large strip of foam tape, wrap the
Piezo Buzzer. (Fig. B3)
5. Secure the Buzzer to the vehicleÕ
s harness
with two large wire ties. (Fig. B3)
i.
Secure the Buzzer so its hole is angled
down.
Piezo
Buzzer Õs
2P
Fo am
Tape
ii. Do not secure the piezo buzzer to the
hood release cable.
Fig. B3
Side Cutter
iii. Clip the wire ties.
Medium
Wir e Tie
C. V3 Harness and V3 ECU Installation
1. Locate the vehicle harnessÕwhite 6P
connector from the Driver Side cowl area.
(Fig. C1)
2. Plug in the V3 harnessÕ6P connector into
the vehicle harnessÕ6P connector.
(Fig. C1)
i.
Verify the connectors are plugged in
securely.
V3 Har ness
V3 Har nessÕ
6P
Vehicl e Har nessÕ
6P ( White)
Fig. C1
3. Secure the V3 harness to the vehicle
harness with one medium wire tie.
(Fig. C1)
Butyl Tape
i.
Clip the wire tie.
4. Remove the backing sheet from the butyl
tape, then apply to the top of the V3
ECU as shown. (Fig. C2)
i.
V3 ECU
Remove only one backing sheet from
the butyl tape.
ii. Press the butyl tape firmly onto the
ECU, making sure they make
complete contact.
Fig. C2
Rev.: C: 10/02/00
Page 5 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
5. Plug in the V3 harnessÕtwo 10P
connectors and 4P connector to the V3
ECU. (Fig. C3)
i.
Verify the connectors are plugged in
securely.
EXAMPLE
V3 ECU
V3 Har nessÕ 4P
V3 Har nessÕ
10P
V3 Har nessÕ
10P
Fig. C3
6. Using 3M Prep Solvent 70, clean the
surface of the Driver Side cowl area as
shown. (Fig. C4)
i.
Remove and save the foam block
from the driverÕ
s side lower cowl hole.
V3 Har ness
7. Remove the backing sheet from the butyl
tape, then attach the V3 ECU to the
shaded area of the Driver Side cowl area
as shown. (Fig. C4)
i.
Press the V3 ECU firmly to the
Driver Side cowl area.
Butyl Tape
Foam Bl ock
V3 ECU
Fig. C4
8. Using the extra large wire tie, secure the
V3 ECU to the Driver Side cowl area as
shown. (Fig. C5)
i.
Reinsert the foam block in the
driverÕ
s side lower cowl hole.
Side Cutter
V3 Har ness
Medium
Wir e Tie
V3 ECU
ii. Clip the wire tie.
9. Secure the V3 harness to the V3 ECU
with one medium wire tie. (Fig. C5)
i.
Clip the wire tie.
Extr a Lar ge
Wir e Tie
Fig. C5
Rev.: C: 10/02/00
Page 6 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
10. Attach two large foam tapes to the surface
of the V3 ECU. (Fig. C6)
V3 ECU
Lar ge Foam Tape ( x2)
Fig. C6
11. Remove the white 14P connector from
the Driver Side J/B. (Fig. C7)
i.
Do not pull on the wires; pull on the
connector.
Vehicl e Har nessÕ
14P ( White)
Dr iver Side J/ B
Fig. C7
12. Plug in the V3 harnessÕ14P connectors
between the DriverÕ
s Side J/B and vehicle
harnessÕ white14P connector. (Fig. C8)
i.
Verify the connectors are plugged in
securely.
13. Secure the V3 harness to the Driver Side
J/B with one large wire tie as shown.
(Fig. C8)
i.
Side Cutter
Dr iver Side J/ B
V3 Har nessÕ
14P
Vehicl e
Har nessÕ
14P
Clip the wire tie.
V3 Har nessÕ
14P
Rev.: C: 10/02/00
Page 7 of 22 Pages
Lar ge wir e tie
Fig. C8
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
14. Using the small foam tape, attach the V3
harness and 14P connector to the Driver
Side J/B. (Fig. C9)
Dr iver Side
J/ B
Smal l
Fo am
Tape
Fig. C9
15. Secure the V3 harness to the vehicleÕ
s
harness with one medium wire ties.
(Fig. C10)
i.
Side Cutter
Dr iver Side J/ B
V3 Har ness
Clip the wire tie.
Medium
Wir e Tie
Fig. C10
D. GBS ECU Installation and Connection
GBS ECU
1. Attach the small foam tape to the edge of
the GBS ECU. (Fig. D1)
Connector
Smal l Foam Tape
Rev.: C: 10/02/00
Page 8 of 22 Pages
Fig. D1
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
Smal l Fl at Bl ade Scr ewdr iver
2. Turn the adjustment screw on the GBS
ECU to the "5" position. (Fig. D2)
Adju stment Screw
GBS ECU
i.
Adjust as necessary during the
functional verifications.
5
4
3
2
3. Insert two medium wire ties through the
slits in the back of the GBS ECU.
(Fig. D2)
6 7
1
8
9
10
11
GBS Setting
Medium Wir e Ties ( x2)
4. Plug in the V3 harnessÕclear 6P
connector into the GBS ECU. (Fig. D3)
i.
i.
Side Cutter
Medium wir e ties ( x2)
Verify the connector is plugged in
securely.
5. Secure the GBS ECU to the vehicle
harness near Driver Side J/B as shown.
(Fig. D3)
Fig. D2
V3 Har nessÕ
6P ( Cl ear )
Clip the wire ties.
GBS ECU
Dr iver Side J/ B
Fig. D3
E. V3 Harness Installation(Continued)
1. Locate and disconnect the 8P connector
from the ignition switch. (Fig.E1)
i.
I gnition Switch
Do not pull on the wires; pull on the
connector.
Vehicl e Har nessÕ
8P( White)
Fig. E1
Rev.: C: 10/02/00
Page 9 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
2. Plug in the V3 harnessÕ8P connectors
between the vehicle harnessÕ8P connector
and the ignition switch. (Fig. E2)
i.
Existing Cl ip
Verify the connectors are plugged in
securely.
3. Secure the V3 harness with the existing
clip. (Fig. E2)
V3 Har nessÕ
8P
V3 Har ness
Vehicl e Har nessÕ
8P ( White)
4. Using one medium wire tie, secure the
V3 harnessÕ8P connectors to the existing
wire tie around the ignition switch
cylinder. (Fig. E3)
i.
G RA Y
Antenna Wir e
Fig. E2
Side Cutter
Existing Wir e Tie
Medium
Wir e Tie
Clip the medium wire tie.
8P
V3 Har ness
F. Antenna Wire Installation
Side Cutter
1. Route the GRAY Antenna wire up the
ignition switch cylinder, then secure it to
the cylinder with a large wire tie.
(Fig. F1)
i.
Fig. E3
G RA Y
Antenna Wir e
I gnition Switch
Cyl inder
CUT !
Lar ge
Wir e Tie
Pull the wire tie very tight.
ii. Clip the wire tie.
2. Cut off the excess Antenna wire as show.
(Fig. F1)
i.
Do not cut any other wires.
Rev.: C: 10/02/00
V3 Har ness
Page 10 of 22 Pages
Fig. F1
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
3. Route the V3 harness toward the center
console area , then secure it to the vehicle
harness with one medium wire tie.
(Fig. F2)
i.
Side Cutter
Par king Br ake Lever
Clip the wire tie.
V3 Har ness
V3 Har nessÕ
2P ( Bl ue)
Medium
Wir e Tie
G. Status Monitor Installation and Connection
V3
Har nessÕ
2P ( Cl ear )
Fig. F2
2P ( Cl ear , Bl ue)
1. With the bracket cover loosened, reach
behind and remove the middle knockout
cover from the bracket cover. (Fig. G1)
i.
Do not scratch the cover.
Status Monitor
ii. Do not bent the cover.
2. Install Status monitor to the bracket
cover.
Br acket Cover
Fig. G1
3. Connect the V3 harnessÕclear and blue
2P connectors to the Status MonitorÕ
s
clear and blue 2P connectors, then wrap
them with a large strip of foam tape.
(Fig. G2)
i.
Br acket Cover
2P ( Cl ear )
Verify the connector are plugged in
securely.
2P ( Bl ue)
Lar ge Foam Tape
Status Monitor
Pr otective Sheet
Rev.: C: 10/02/00
Page 11 of 22 Pages
Fig. G2
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section II − Installation Procedure
H. Warning Label Installation
1. Clean the inside surface of the front
doorÕ
s windows. (Fig. H1)
1 0 mm
2. Place the warning label on the inside
surface of the front doorÕ
s windows as
shown. (Fig. H1)
i.
War ning Label
Use a piece of clear adhesive tape to
lift the labels off of their protective
backing sheet.
ii. Do not touch the adhesive surface of
the warning labels.
Fig. H1
I. Completing the Installation
10mm Soc k et
45û
1. Complete the reassembly of the vehicle.
i.
Reconnect any disconnected
connectors.
Negative
Batter y
Cabl e
ii. Verify the panels fit together properly
with no uneven gaps between them.
Battery
2. Clean up and remove any trash.
3. Reconnect the vehicleÕ
s negative battery
cable. (Fig. I1)
i.
Attach the battery cable at a 45
degree angle as shown.
ii. Tighten the nut with 3 ft¥lbs of
torque.
iii. Be careful to not touch the positive
battery terminal.
4. Place the remote controls, ownerÕ
s guide
and insurance card, left in their protective
bags, into the glove box.
Rev.: C: 10/02/00
Page 12 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section III − Functional Verifications
Section III − Functional Verifications
Check:
Look for:
Press and release the remoteÕ
s top button
to arm the system.
The tail and marker lights flash once.
The Piezo chirps once.
The interior lights turn on for three seconds.
Both doors lock.
The Status MonitorÕ
s LED starts flashing.
Press and release the remoteÕ
s top button
again to disarm the system.
The tail and marker lights flash twice.
The Piezo chirps twice.
The interior lights turn on for thirty seconds.
Both doors unlock.
The Status MonitorÕ
s LED stops flashing.
Open and close the driverÕ
s door.
Arm and disarm the system with the
remote again, then wait thirty seconds.
The tail and marker lights flash once.
The Piezo chirps once.
The interior lights turn on for three seconds.
Both doors lock.
The Status MonitorÕ
s LED starts flashing.
Press and release the remoteÕ
s top button
again to disarm the system.
The tail and marker lights flash twice.
The Piezo chirps twice.
The interior lights turn on for thirty seconds.
Both doors unlock.
The Status MonitorÕ
s LED stops flashing.
Open the driverÕ
s door, then press and
release the remoteÕ
s top button.
The Piezo sounds continuously.
Close the driverÕ
s door.
The Piezo stops sounding.
Pressand hold the remoteÕ
s top button for
more than two seconds.
The doors lock, then unlock.
The Piezo chirps once (when the doors lock), then
twice (when the doors unlock.)
The horn sounds in a unique pattern.
The interior lights flash in the same pattern.
The tail and marker lights flash in the same
pattern.
The Status MonitorÕ
s LED flashes in the same
pattern.
Rev.: C: 10/02/00
Page 13 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section III − Functional Verifications
Section III − Functional Verifications
Check:
Look for:
Press and release the remoteÕ
s top button.
The horn stops sounding.
All the lights stop flashing.
The Piezo chirps twice.
Sit in the driverÕ
s seat and make sure both
doors are closed.
Insert the key into the ignition switch and
turn it to ÒONÓ.
Both doors lock.
Turn the key back to ÒACCÓ.
Both doors unlock.
Turn the key to ÒONÓ,roll down both
windows, turn the key back to ÒLOCKÓ,
then remove it and exit the vehicle.
Press and release the remoteÕ
s top button
to arm the system.
The tail and marker lights flash once.
The Piezo chirps once.
The interior lights turn on for three seconds.
Both doors lock.
The Status MonitorÕ
s LED starts flashing.
Reach inside, unlock and open driverÕ
s
door, then sit in the driverÕ
s seat.
The horn sounds in a unique pattern.
The interior lights flash in the same pattern.
The tail and marker lights flash in the same
pattern.
The Status MonitorÕ
s LED flashes in the same
pattern.
(If checking a M/T vehicle, fully depress
the clutch pedal for the next step.)
Insert the key into the ignition switch and
turn it to ÒSTARTÓ.
The engine does not start (no cranking).
Turn the key back to ÒACCÓ,then to
ÒSTARTÓ again.
The horn stops sounding.
All the lights stop flashing.
The Status MonitorÕ
s LED stops flashing.
The starter cranks and the engine starts.
Turn the key back to ÒLOCKÓ,remove it,
exit the vehicle, then check the front pas−
senger door without performing the starter
cut check.
Same as before.
Rev.: C: 10/02/00
Page 14 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section III − Functional Verifications
Section III − Functional Verifications
Check:
Look for:
Roll up both windows, remove the key
and exit the vehicle.
Press and release the remoteÕ
s top button
to arm the system.
The tail and marker lights flash once.
The Piezo chirps once.
The interior lights turn on for three seconds.
Both doors lock.
The Status MonitorÕ
s LED starts flashing.
Pull the plunger on the striker tool 1/3 to
1/2 way out, then release it to strike the
center of the driverÕ
s door window.
The alarm should no
t betriggered.
Pull the plunger all the way out to tap the
center of the driverÕ
s door window again.
The horn starts sounding.
The tail and marker lights starts flashing.
Note: If you do not disarm the system with the
remote control, the horn will sound and
the lights will flash for 20 seconds. It is
not necessar
y to checkthe alarm duration.
Disarm the system with the remote.
Rev.: C: 10/02/00
The horn stops sounding.
All the lights stop flashing.
The Status MonitorÕ
s LED stops flashing.
Page 15 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section IV − Installation Process/Audit Criteria
Section IV: Process/Audit Criteria
Audit
Process
Audited during accessory installation
Audited on completed vehicle installation
Paragraph numbers refer to paragraph numbers in Section II
Part Number : 08586−3D841
A. Vehicle Disassembly
1. Disconnect the negative battery cable.
(Fig. A1)
i.
Cover the fender before starting.
ii.
Be careful to not touch the positive battery
terminal.
2. Remove the driverÕ
s step cover. (Fig. A2)
i.
Protect the seat and floor before starting.
iii. Do not scratch the cover.
3. Remove the driverÕ
s cowl cover. (Fig. A3)
i.
Do not scratch the cover.
4. Remove the hood release lever. (Fig. A4)
i.
Remove the two screws securing the lever to
the lower dash cover.
ii.
Remove the cable from the lever.
5. Remove the lower dash cover. (Fig. A4)
ii.
Do not scratch the cove
6. Loosen the vehicleÕ
s wire harness if so equipped.
(Fig. A5)
i.
Unfasten the clips securing the harness.
7. Remove the middle heater duct. (Fig. A6)
i.
Remove the screw securing the heater ductÕ
s
bracket to the vehicle.
8. Prepare a protective sheet, then place protective
sheet over the front edge of the center console.
(Fig. A7)
Rev.: C: 10/02/00
Page 16 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section IV − Installation Process/Audit Criteria
Section IV: Process/Audit Criteria
Audit
Process
Audited during accessory installation
Audited on completed vehicle installation
Paragraph numbers refer to paragraph numbers in Section II
9. Loosen the bracket cover, but do not remove the
cover. (Fig. A8)
i.
Remove the two clips securing the bracket
cover.
ii.
Do not scratch the cover.
iii. Do not bend the cover.
B.
Piezo Buzzer Installation
1. Remove and save the three bolts securing R/B No. 2
to the body in the engine room. (Fig B1)
2. Locate the vehicle harnessÕgray 2P connector, then
remove and discard the black cap. (Fig. B2)
ii.
Pull the connector toward the battery to
remove the cap and make the connection.
3. Connect the Piezo BuzzerÕ
s gray 2P connector to the
vehicle harnessÕ 2P gray conne
ctor. (Fig. B3)
i.
Verify the connectors are plugged in securely.
4. Using a large strip of foam tape, wrap the Piezo
Buzzer. (Fig. B3)
5. Secure the Buzzer to the vehicleÕ
s harness with two
large wire ties. (Fig. B3)
i.
Secure the Buzzer so its hole is angled down.
ii. Do not secure the piezo buzzer to the hood
release cable.
iii. Clip the wire ties.
Rev.: C: 10/02/00
Page 17 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section IV − Installation Process/Audit Criteria
Section IV: Process/Audit Criteria
Audit
Process
Audited during accessory installation
Audited on completed vehicle installation
Paragraph numbers refer to paragraph numbers in Section II
C. V3 Harness and V3 ECU Installation
2. Plug in the V3 harnessÕ 6P conne
ctor into the
vehicle harnessÕ 6P connec
tor. (Fig. C1)
i.
Verify the connectors are plugged in securely.
3. Secure the V3 harness to the vehicle harness with
one medium wire tie. (Fig. C1)
i.
Clip the wire tie.
4. Remove the backing sheet from the butyl tape,
then apply to the top of the V3 ECU as shown.
(Fig. C2)
i.
Remove only one backing sheet from the
butyl tape.
ii.
Press the butyl tape firmly onto the ECU,
making sure they make complete contact.
5. Plug in the V3 harnessÕ tw
o 10P connectors and
4P connector to the V3 ECU as shown. (Fig. C3)
i.
Verify the connectors are plugged in securely.
6. Using 3M Prep Solvent 70, clean the surface of
the Driver Side cowl area as shown. (Fig. C4)
i.
Remove and save the foam block from the
driverÕ
s side lower cowl hole.
7. Remove the backing sheet from the butyl tape,
then attach the V3 ECU to the shaded area of the
Driver Side cowl area as shown. (Fig. C4)
i.
Press the V3 ECU firmly to the Driver Side
cowl area.
Rev.: C: 10/02/00
Page 18 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section IV − Installation Process/Audit Criteria
Section IV: Process/Audit Criteria
Audit
Process
Audited during accessory installation
Audited on completed vehicle installation
Paragraph numbers refer to paragraph numbers in Section II
8. Using the extra large wire tie, secure the V3 ECU
to the Driver Side cowl area as shown. (Fig. C5)
i.
Reinsert the foam block in the driverÕ
s side
lower cowl hole.
ii.
Clip the wire tie.
9. Secure the V3 harness to the V3 ECU with one
medium wire tie. (Fig. C5)
i.
Clip the wire tie.
11. Remove the white 14P connector from the Driver
Side J/B. (Fig. C7)
i.
Do not pull on the wires; pull on the
connector.
12. Plug in the V3 harnessÕ14P connectors between
the DriverÕ
s Side J/B and vehicle harnessÕ wh
ite
14P connector. (Fig. C8)
i.
Verify the connectors are plugged in securely.
13. Secure the V3 harness to the Driver Side J/B with
one large wire tie as shown. (Fig. C8)
i.
Clip the wire tie.
15. Secure the V3 harness to the vehicleÕ
s harness with
one medium wire ties. (Fig. C10)
i.
Clip the wire tie.
Rev.: C: 10/02/00
Page 19 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section IV − Installation Process/Audit Criteria
Section IV: Process/Audit Criteria
Audit
Process
Audited during accessory installation
Audited on completed vehicle installation
Paragraph numbers refer to paragraph numbers in Section II
D. GBS ECU Installation and Connection
1. Attach the small foam tape to the edge of the GBS
ECU. (Fig. D1)
2. Turn the adjustment screw on the GBS ECU to
the "5" position. (Fig. D2)
i.
Adjust as necessary during the functional
verifications.
3. Insert two medium wire ties through the slits in
the back of the GBS ECU. (Fig. D2)
4. Plug in the V3 harnessÕ clea
r 6P connector into
the GBS ECU. (Fig. D3)
i.
Verify the connector is plugged in securely.
5. Secure the GBS ECU to the vehicle harness near
Driver Side J/B as shown. (Fig. D3)
i.
E.
Clip the wire ties.
V3 Harness Installation(Continued)
1. Locate and disconnect the 8P connector from the
ignition switch. (Fig.E1)
i.
Do not pull on the wires; pull on the
connector.
2. Plug in the V3 harnessÕ 8P conne
ctors between
the vehicle harnessÕ 8Pconnector and the ignition
switch. (Fig. E2)
i.
Verify the connectors are plugged in securely.
3. Secure the V3 harness with the existing clip. (Fig.
E2)
Rev.: C: 10/02/00
Page 20 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section IV − Installation Process/Audit Criteria
Section IV: Process/Audit Criteria
Audit
Process
Audited during accessory installation
Audited on completed vehicle installation
Paragraph numbers refer to paragraph numbers in Section II
4. Using one medium wire tie, secure the V3
harnessÕ 8P conne
ctors to the existing wire tie
around the ignition switch cylinder. (Fig. E3)
i.
F.
Clip the medium wire tie.
Antenna Wire Installation
1. Route the GRAY Antenna wire up the ignition
switch cylinder, then secure it to the cylinder with
a large wire tie. (Fig. F1)
i.
Pull the wire tie very tight.
ii.
Clip the wire tie.
2. Cut off the excess Antenna wire as show. (Fig. F1)
i.
Do not cut any other wires
3. Route the V3 harness toward the center console
area , then secure it to the vehicle harness with
one medium wire tie.
(Fig. F2)
i.
Clip the wire tie.
G. Status Monitor Installation and Connection
1. With the bracket cover loosened, reach behind
and remove the middle knockout cover from the
bracket cover. (Fig. G1)
i.
Do not scratch the cover.
ii.
Do not bend the cover.
2. Install Status monitor to the bracket cover.
3. Connect the V3 harnessÕ clearand blue 2P
connectors to the Status MonitorÕ
s clear and blue
2P connectors, then wrap them with a large strip
of foam tape. (Fig. G2)
i.
Verify the connector are plugged in securely.
Rev.: C: 10/02/00
Page 21 of 22 Pages
PPO
TOYOTA
TACOMA
2001 −
TVIP V3 (RS3000)
Section IV − Installation Process/Audit Criteria
Section IV: Process/Audit Criteria
Audit
Process
Audited during accessory installation
Audited on completed vehicle installation
Paragraph numbers refer to paragraph numbers in Section II
H. Warning Label Installation
1. Clean the inside surface of the front doorÕ
s
windows. (Fig. H1)
2. Place the warning label on the inside surface of the
front doorÕ
s windows as shown. (Fig. H1)
I.
i.
Use a piece of clear adhesive tape to lift the
labels off of their protective backing sheet.
ii.
Do not touch the adhesive surface of the
warning labels.
Completing the Installation
1. Complete the reassembly of the vehicle.
i.
Reconnect any disconnected connectors.
ii.
Verify the panels fit together properly with no
uneven gaps between them.
3. Reconnect the vehicleÕ
s negative battery cable.
(Fig. I1)
ii.
Be careful to not touch the positive battery
terminal.
4. Place the remote controls, ownerÕ
s guide and
insurance card, left in their protective bags, into
the glove box.
Rev.: C: 10/02/00
Page 22 of 22 Pages
3.
i. Attach the battery cable at a 45 degree
angle as shown.
ii. Tighten the nut with 3 ft¥lbs of torque.
PPO
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement