Zenith P42W24BX Installation and Operating manual

Add to my manuals
36 Pages

advertisement

Zenith P42W24BX Installation and Operating manual | Manualzz

Installation and Operating Guide

Model Number | P42W24Bx | PLASMA DISPLAY PANEL

© Copyright 2003, Zenith Electronics Corporation.

Warning

W arning

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

FCC NOTICE

• A Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics

Corporation. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is:

Zenith Electronics Corporation

2000 Millbrook Drive

Lincolnshire, Il 60069, USA

Phone: 1-847-941-8000

WARNING

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO

RAIN OR MOISTURE.

2 Plasma Display

Safety Instructions

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards

Association.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

12. Power-Cord Polarization

This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

PORTABLE CART WARNING

Owner’s Manual 3

Safety Instructions

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Example of Grounding According to National

Electrical Code Instructions

Ground Clamp

Antenna Lead in Wire

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been damaged.

f. If the product exhibits a distinct change in performance.

Electric Service

Equipment

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

NEC - National Electrical Code

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

4 Plasma Display

Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4

Introduction

Controls and Connection Options . . . . . . . . . . . .7

Remote Control Key Functions . . . . . . . . . . . . . .8

Installation

Installation Instruction . . . . . . . . . . . . . . . . . . . .9~10

External Equipment Connections . . . . . . . . . .11~14

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11

External A/V Source Setup . . . . . . . . . . . . . . . .12

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14

Operation

Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .15

Menu Language Selection . . . . . . . . . . . . . . . . . .15

Video Menu Options

APC (Auto Picture Control) . . . . . . . . . . . . . . . .16

Manual Picture Control . . . . . . . . . . . . . . . . . . .16

Auto Color Temperature Control . . . . . . . . . . . .16

Manual Color Temperature Control . . . . . . . . . .16

Audio Menu Options

DASP (Digital Auto Sound Processing) . . . . . . .17

AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .17

Manual Sound Control . . . . . . . . . . . . . . . . . . .17

Time Menu Options

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . .18

Setting the On/Off Timer . . . . . . . . . . . . . . . . .18

Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Special Menu Options

Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ISM (Image Sticking Minimization) Method . . . .19

Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Screen Menu Options

Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .20

Setting Picture Format . . . . . . . . . . . . . . . . . . .20

Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . .20

Adjusting Horizontal/Vertical Position . . . . . . . .21

Manual Configure . . . . . . . . . . . . . . . . . . . . . . .21

Screen Adjustments . . . . . . . . . . . . . . . . . . . . .21

Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Luminance Noise Reduction . . . . . . . . . . . . . . .22

Selecting Wide VGA mode . . . . . . . . . . . . . . . .22

Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

PIP (Picture In Picture) Feature

Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23

PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Swapping PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23

Selecting a Input Signal Source for PIP . . . . . . .23

PIP Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . .23

Double Window Setup Options

Watching Double Window . . . . . . . . . . . . . . . . .24

Sub Picture Size Adjustment . . . . . . . . . . . . . . .24

Swapping the Double Window . . . . . . . . . . . . .24

Selecting a Source for the Double Window . . . .24

External Control Device Setup . . . . . . . . . . . . . . . .25~30

IR Code (NEC format) . . . . . . . . . . . . . . . . . . . . . . .31~32

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .33

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

After reading this manual, keep it handy for future reference.

Owner’s Manual 5

Introduction

What is a Plasma Display Panel (PDP)?

If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room.

Wide Screen

The screen of the Plasma Display is 42" so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit.

The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective.

Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects during the manufacture and operation of this product.

Cooling Fan Noise

In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP.

The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.

6 Plasma Display

Introduction

ON/OFF

INPUT

SELECT

MENU VOL.

E

,

D

Buttons

Main Power Button

INPUT SELECT Button

Remote Control Sensor

VOLUME (

F

,

G

) Buttons

MENU Button

Power Standby Indicator

Illuminates red in standby mode,

Illuminates green when the

Monitor is turned on

( )

R

( ) ( )

L

( )

EXTERNAL SPEAKER

RS-232C INPUT

(CONTROL/SERVICE)

DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT

EXPANDED

INPUT

1 2 3 4 5

R AUDIO L

Y P

B

P

R

R AUDIO L (MONO)

AUDIO INPUT COMPONENT INPUT

REMOTE

CONTROL

S-VIDEO

VIDEO

INPUT

AUDIO INPUT

6 7 8

AC INPUT

9

1.

EXTERNAL SPEAKER (8 ohm output)

Connect to optional external speaker(s).

* For further information, refer to ‘Speaker & Speaker

Stand’ manual.

2.

RS-232C INPUT (CONTROL/SERVICE) PORT

Connect to the RS-232C port on a PC.

3.

DVI (Digital Visual Interface) INPUT/

RGB INPUT/AUDIO INPUT JACKS

Connect the monitor output connector of a PC to the appropriate input port.

4.

RGB OUTPUT JACKS

You can watch the RGB signal on another monitor, connect

RGB OUTPUT to another monitor’s PC input port.

5.

EXPANDED INPUT

6.

COMPONENT INPUT/AUDIO INPUT JACKS

Connect a component video/audio device to these jacks.

7.

REMOTE CONTROL

Connect your wired remote control to the remote control port on the Monitor.

8.

S-VIDEO INPUT

Connect S-Video out from an S-VIDEO VCR to the S-

VIDEO input.

AUDIO/VIDEO INPUT JACKS

Connect audio/video out from external equipment to these jacks.

9.

POWER CORD SOCKET

This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power.

Owner’s Manual 7

Introduction

- When using the remote control, aim it at the remote control sensor on the monitor.

- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary.

POWER

Switches the monitor between

ON and STANDBY.

MULTIMEDIA

Selects:

Component

,

RGB

, or

DVI

mode.

APC

Adjusts the factory preset picture according to the room.

ARC

Changes the picture format.

PIP

Switches the sub picture on and off.

SWAP

Exchanges main and sub picture images.

MENU

Displays on screen menus.

Exits the current menu.

NUMBER buttons

WIN.POSITION

Moves the sub picture.

SPLIT ZOOM

Enlarge the screen with regular ration.

Not functional

POWER

MULTIMEDIA INPUT SELECT

APC

ARC

DASP

SLEEP

PIP DW

SWAP

MENU CH

PIP INPUT

MUTE

VOL

ENTER

VOL

1

4

7

WIN.POSITION

CH

2

5

8

0

3

6

9

WIN.SIZE

SPLIT ZOOM ZOOM ZOOM +

A.PROG

MEMORY/ERASE PIP CH

CAPTION

FAV CH

PIP CH

POWER MTS

STOP

REW

P/STILL

PLAY

REC

FF

INPUT SELECT

Selects source:

Component

DASP

Selects the sound appropriate to your viewing program character:

Flat

,

Music

,

Movie

,

Sports

, or

User.

SLEEP

Sets the Sleep Timer.

DW (Double Window)

Selects Double Window mode.

PIP INPUT

Selects the input mode for the sub picture.

MUTE

Switches the sound on or off.

ENTER

CH

D

/

E

(Channel button)

Selects menu options.

VOL

F

/

G

(Volume button)

Increases/decreases sound level.

Adjusts menu settings.

WIN. SIZE

Video

,

S-Video

,

RGB

, or

DVI

mode.

Adjusts the sub picture size.

ZOOM-/ZOOM+

Enlarges or reduces the main picture size.

VCR BUTTONS

Control some video cassette recorders.

,

• Open the battery compartment cover on the back side and insert the batteries with correct polarity.

• Install two 1.5V alkaline batteries of AAA type. Don’t mix used batteries with new batteries.

8 Plasma Display

Installation

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.

1.5V

1.5V

POWER

SLEEP

APC

ARC

PIP

SWAP

MENU

INPUT SELECT

DASP

PIP ARC

TWIN PICTURE

SUB INPUT

MUTE

VOL OK VOL

1

4

7

2

5

8

0

3

6

9

POWER STOP

REW PLAY

P/STILL

FF

REC

WIN.SIZE WIN.POSITION

SPLIT ZOOM

ZOOM ZOOM +

Owner’s Manual Alkaline Batteries

BNC-RCA Adapter

Remote Control

D-sub 15 pin Cable Power Cord DVI-D Cable

• The Monitor can be installed in various ways such as on a wall, or on a desktop etc.

• The plasma display is designed to be mounted horizontally. The speakers depicted are optional.

GROUNDING

Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Short-circuit

Breaker

Power

Supply

W

all Mount Installation

For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are included from your dealer in the optional Wall

Mounting Bracket Installation and Setup Guide.

2 inches

4 inches

4 inches 4 inches

4 inches

Owner’s Manual 9

Installation

For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide, see your dealer.

2 inches

4 inches

4 inches

4 inches

2.36 inches

10 Plasma Display

Installation

NOTE: All cables shown are not included with the plasma display.

- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor

- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen.

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s

VIDEO INPUT.

2. Connect the audio and video cables from the VCR's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to a VCR, match the jack colors: (Video

= yellow, Audio Left = white, and Audio Right = red).

VCR: Connect the video output cable from the VCR to the

VIDEO input on the monitor.

S-VIDEO VCR: Connect the S-Video output cable from the

VCR to the S-VIDEO input. (Note that S-Video yields higher quality video).

How to use

1. Insert a video tape into the VCR and press PLAY on the VCR.

(Refer to the VCR owner’s manual.)

2. Use the INPUT SELECT button on the remote control to select

Video.

(If connected to S-VIDEO, select the S-Video external input source.)

S-VIDEO

OUT

(R) AUDIO (L)

IN

VIDEO

R

AUDIO L

Y PB PR

R AUDIO L (MONO)

AUDIO INPUT COMPONENT INPUT

REMOTE

CONTROL

S-VIDEO

VIDEO

INPUT

AUDIO INPUT

VCR

Cable

TV Setup

- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming.

The monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor.

- For further information regarding cable TV service, contact your local cable TV service provider(s).

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s

VIDEO INPUT.

2. Connect the audio and video cables from the cable box's output jacks to the monitor input jacks, as shown in the figure.

When connecting the monitor to a cable TV, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Use the INPUT SELECT button on the remote control to select Video.

2. Select your desired channel with the cable box remote control.

R AUDIO L

Y PB PR

R AUDIO L (MONO)

AUDIO INPUT COMPONENT INPUT

REMOTE

CONTROL

S-VIDEO

VIDEO

INPUT

AUDIO INPUT

TV

VCR

(R) AUDIO (L) VIDEO

RF Cable

Cable Box

Owner’s Manual 11

Installation

External

A/V Source Setup

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s

VIDEO INPUT.

2. Connect the audio and video cables from the external equipment's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to external equipment, match the jack colors (Video = yellow, Audio

Left = white, and Audio Right = red).

How to use

1. Use the INPUT SELECT button on the remote control to select Video.

2. Operate the corresponding external equipment. Refer to external equipment operating guide.

R AUDIO L

Y P

B

P

R R

AUDIO

L (MONO)

AUDIO INPUT COMPONENT INPUT

REMOTE

CONTROL

S-VIDEO

VIDEO

INPUT

AUDIO INPUT

(R) AUDIO (L) B R

or

DVD

(R) AUDIO (L) S-VIDEO

R AUDIO L

Y P

B

P

R

R AUDIO L (MONO)

AUDIO INPUT COMPONENT INPUT

REMOTE

CONTROL

S-VIDEO

VIDEO

INPUT

AUDIO INPUT

Camcorder

Video game set

R

AUDIO

L

VIDEO

How to connect

1. Connect the DVD video outputs to the COMPONENT (Y, P

B

, P

R

)

INPUT jacks and connect the DVD audio outputs to the AUDIO

INPUT jacks on the monitor, as shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to the

S-VIDEO input on the monitor and connect the DVD audio outputs to the AUDIO INPUT jacks, as shown in the figure.

How to use

1. Turn on the DVD player, insert a DVD

2. Use the INPUT SELECT button on the remote control to select

Component. (If connected to S-VIDEO, select the S-Video external input source.)

3. Refer to the DVD player's manual for operating instructions.

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports of the

Monitor

Y P

B

P

R

Video output ports of DVD player

Y

Y

Y

Y

Pb

B-Y

Cb

P

B

Pr

R-Y

Cr

P

R

- To watch digitally broadcast programs, purchase and connect a digital set-top box.

- This monitor supports HDCP (High-bandwidth Digital

Contents Protection) protocol for DTV

(480p,720p,1080i) modes.

How to connect

1. Use the monitor’s COMPONENT (Y, P

B

, P

R

) INPUT,

RGB or DVI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

2. Use INPUT SELECT on the remote control to select

Component, RGB or DVI.

DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT

EXPANDED

INPUT

R AUDIO L

Y P

R R AUDIO L (MONO)

AUDIO INPUT COMPONENT INPUT

REMOTE

CONTROL

S-VIDEO

VIDEO

INPUT

AUDIO INPUT

DVI-DTV OUTPUT

(R) AUDIO (L)

or

RGB-DTV OUTPUT

(R) AUDIO (L)

or

Digital Set-top Box

(R) AUDIO (L)

B R

12 Plasma Display

Installation

- This Plasma display provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data

Channel (DDC) protocol.

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

2. Use the monitor’s RGB INPUT or DVI (Digital

Visual Interface) INPUT port for video connections, depending on your PC connector.

If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI INPUT to display the PC image on the monitor.

If the graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB or DVI; (the other mode is set to Plug and Play automatically by the monitor.)

3. Then, make the corresponding audio connections.

If using a sound card, adjust the PC sound as required.

( )

R

( ) ( )

EXTERNAL SPEAKER

L

( )

RS-232C INPUT

(CONTROL/SERVICE)

DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT

EXPANDED

INPUT

How to use

1. Turn on the PC and the monitor.

2. Turn on the display by pressing the POWER button on the monitor's remote control.

3. Use the INPUT SELECT button on the remote control to select RGB or DVI.

4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

NOTES

• Depending on the graphics card, DOS mode may not work if you use a DVI-I cable.

• Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible.

• The synchronization input form for Horizontal and Vertical frequencies is separate.

Owner’s Manual 13

Installation

RGB/DVI Mode

Resolution

640x350

720x400

640x480

848x480

852x480

Horizontal

Frequency(KHz)

31.468

37.861

Vertical

Frequency(Hz)

70.09

85.08

31.469

37.927

31.469

35.000

37.861

37.500

43.269

31.5

35

37.5

31.5

35

37.5

70.08

85.03

59.94

66.66

72.80

75.00

85.00

60.00

70.00

75.00

60.00

70.00

75.00

Resolution

800x600

832x624

1024x768

1152x864

1152x870

1280x960

1280x1024

Horizontal

Frequency(KHz)

35.156

37.879

Vertical

Frequency(Hz)

56.25

60.31

48.077

46.875

53.674

49.725

48.363

54.476

60.023

54.348

63.995

67.500

68.681

60.000

63.981

72.18

75.00

85.06

74.55

60.00

70.06

75.02

60.05

70.01

75.00

75.06

60.00

60.02

14 Plasma Display

T urning on the Monitor

Turning on the Monitor just after installation

1. Connect power cord correctly.

2. Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT,

MULTIMEDIA button on the remote control to switch the Monitor on.

Turning on the Monitor (power cord is still connected)

1. If the Monitor was turned off with the ON/OFF button on the Monitor

• Press the ON/OFF button on the Monitor to turn the Monitor on.

2. If the Monitor was turned off with the remote control and the ON/OFF button on the Monitor

• Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the

Monitor. Or, on the remote control, press POWER, INPUT SELECT, or MULTIMEDIA to turn the

Monitor on.

- The menus can be shown on the screen in the selected language. First select your language.

1. Press the MENU button and then use D

/

E button to select the

SPECIAL

menu.

2. Press the

G button and then use D

/

E button to select

Language

.

3. Press the

G button and then use D

/

E button to select your desired language.

From this point on, the on-screen menus will be shown in the language of your choice.

4. Press the ENTER button to save.

Language

Key lock

ISM Method

Low power

Set ID

Caption / Text

Captions

OSD Rotate

G

MENU Prev.

English

Español

Français

Operation

Owner’s Manual 15

Operation

- Each adjustment for the Picture menu options doesn’t effect other input sources. Readjust Picture menu options for each of the following sources:

RGB (PC) / DVI (PC),

RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i)

Video / S-Video / Component (480i)

- APC adjusts the Monitor for the best picture appearance.

- When adjusting picture options (contrast, brightness, color, sharpness and tint) manually, APC automatically changes to

User

.

1. Press the APC button repeatedly to select the picture appearance setup option as shown below.

Clear Optimum Soft User

• You can also adjust

APC

in the

PICTURE

menu.

Clear

,

Optimum

, and

Soft

are preset for good picture quality at the factory and cannot be changed.

Manual Picture Control (

User

option)

- You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer.

APC

ACC

Color temp.

Contrast 80

G

Brightness 60

Color 50

Sharpness 50

Tint 0

MENU Prev.

1. Press the MENU button and then use

D

/

E button to select the

PICTURE

menu.

2. Press the

G button and then use D

/

E button to select the desired picture option

(

Contrast

,

Brightness

,

Color

,

Sharpness

,

Tint

)

.

3. Press the

G button and then use

F

/

G button to make appropriate adjustments.

4. Press the ENTER button to save.

Auto Color T emperature Control

- To initialize values (reset to default settings), select the

Normal

option.

- When adjusting color temperature options (red, green, or blue) manually, ACC automatically changes to

User

.

1. Press the MENU button and then use D

/

E button to select the

PICTURE

menu.

2. Press the G button and then use

D

/

E button to select

ACC

.

3. Press the

G button and then use D

/

E button to select either

Normal

(Default),

Cool

(Preset),

Warm

(Preset) or

User

(Manual Adjustment).

4. Press the ENTER button to save.

APC

ACC

G

Color temp.

Contrast 80

Brightness 60

Color 50

Sharpness 50

Tint 0

MENU Prev.

Normal

Cool

Warm

User

Manual Color T emperature Control (

User

option)

- You can adjust red, green, or blue to any color temperature you prefer.

1. Press the MENU button and then use D

/

E button to select the

PICTURE

menu.

2. Press the

G button and then use D

/

E button to select

Color temp

.

3. Press the G button and then use

D

/

E button to select

Red

,

Green

or

Blue

.

4. Use the

F

/

G button to make appropriate adjustments.

• The adjustment range of

Red

,

Green

, and

Blue

is -20 ~ +20.

5. Press the ENTER button to save.

16 Plasma Display

APC

ACC

Color temp.

G

Contrast 80

Brightness 60

Color 50

Sharpness 50

Tint 0

MENU Prev.

Red 0

Green 0

Blue 0

DASP (Digital Auto Sound Processing)

- This function lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate sound option based on the program content.

- When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to

User

.

1. Press the DASP button repeatedly to select the appropriate sound setup as shown below.

Flat Music Movie Sports User

• You can also adjust

DASP

in the

SOUND

menu.

Flat

,

Music

,

Movie

and

Sports

are preset for good sound quality at the factory and cannot be changed.

A VL (Auto V

olume Leveler)

- AVL maintains an equal sound level; even if you change channels.

1. Press the MENU button and then use

D

/

E button to select the

SOUND

menu.

2. Press the

G button and then use D

/

E button to select

AVL

.

3. Press the G button and then use D

/

E button to select

On

or

Off

.

4. Press the ENTER button to save.

DASP

AVL

Balance 0

Treble 50

Bass 50

G

On

Off

MENU Prev.

Manual Sound Control (

User

option)

- You can adjust sound treble, bass, and balance to the levels you prefer.

1.

Press the MENU button and then use

D

/

E button to select the

SOUND

menu.

2. Press the

G button and then use D

/

E button to select the desired sound option

(

Balance

,

Treble

,

Bass

)

.

3. Press the

G button and then use

F

/

G button to make appropriate adjustments.

4. Press the ENTER button to save.

DASP

AVL

Balance 0

Treble 50

G

Bass 50

MENU Prev.

Operation

Owner’s Manual 17

Operation

T imer Menu Options

- If current time setting is incorrect, reset the clock.

1. Press the MENU button and then use D

/

E button to select the

TIMER

menu.

2. Press the

G button and then use D

/

E button to select

Clock

.

3. Press the G button and then use

D

/

E button to set the hour.

4. Press the G button and then use

D

/

E button to set the minutes.

5. Press the ENTER button to save.

Clock

Off timer

On timer

Auto off

10 : 10

MENU Prev.

Setting the On/Of f T

imers

- Timer functions operate only if current time has been set.

- Off-Timer function overrides On-Timer function if they are set to the same time.

- The monitor must be in standby mode for the On-Timer to work.

1. Press the MENU button and then use D

/

E button to select the

TIMER

menu.

2. Press the

G button and then use D

/

E button to select

Off timer

or

On timer

.

3. Press the G button and then use

D

/

E button to select

On

.

• To cancel

On

/

Off timer

function, select

Off

.

4. Press the

G button and then use D

/

E button to set the hour.

5. Press the G button and then use D

/

E button to set the minutes.

6. For only

On timer

function; Press the G button and then use

D

/

E button to set sound level.

7. Press the ENTER button to save.

Auto Of f

- If there is no input signal, the Monitor will turn off automatically after 10 minutes.

1. Press the MENU button and then use

D

/

E button to select the

TIMER

menu.

2. Press the

G button and then use D

/

E button to select

Auto off

.

3. Press the

G button and then use D

/

E button to select

On

or

Off

.

4. Press the ENTER button to save.

Clock

Off timer

On timer

Auto off

G

On

Off

10 : 30

Vol. 30

Ch. TV 13

MENU Prev.

Clock

Off timer

On timer

Auto off

G

On

Off

MENU Prev.

Sleep T imer

- The Sleep Timer turns the Monitor off at the preset time. Note that this setting is cleared when the monitor is turned off.

zz

1. Press the SLEEP button repeatedly to select the number of minutes. First the ---

Min

option appears on the screen, followed by the following sleep timer options:

10, 20, 30, 60, 90, 120, 180, and 240 minutes.

2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to count down from the number of minutes selected.

3. To check the remaining minutes before the monitor turns off, press the SLEEP or ENTER button once.

4. To cancel the Sleep Timer, press the SLEEP button repeatedly until zz

---

Min

appears.

18 Plasma Display

- The monitor can be set up so that it can only be used with the remote control.

- This feature can be used to prevent unauthorized viewing by disabling the front panel controls.

- This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.

1. Press the MENU button and then use D

/

E button to select the

SPECIAL

menu.

2. Press the G button and then use

D

/

E button to select

Key lock

.

3. Press the

G button and then use D

/

E button to select

On

or

Off

.

4. Press the ENTER button to save.

• With the KEY LOCK ON, the display ‘

Key lock

’ appears on the screen if any button on the front panel is pressed.

Language

Key lock

ISM Method

Low power

Set ID

Caption / Text

Captions

G

On

Off

MENU

Prev.

- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time.

1. Press the MENU button and then use D

/

E button to select the

SPECIAL

menu.

2. Press the G button and then use

D

/

E button to select

ISM Method

.

3. Press the

G button and then use D

/

E button to select either

Normal

,

White wash

,

Orbiter

, or

Inversion

.

Normal

:

If image sticking is never a problem, ISM is not necessary - set to Normal.

White wash

White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press any button.

Orbiter

Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the screen will move every 1 minutes: Right

Right

Downside

Downside

Left

Left

Upside

Upside.

Inversion

Inversion will automatically invert the plasma display panel color every 30 minutes.

Language

Key lock

ISM Method

Low power

Set ID

Caption / Text

Captions

G

MENU Prev.

Normal

White wash

Orbiter

Inversion

4. Press the ENTER button to save.

- Low power reduces the plasma display power consumption.

1. Press the MENU button and then use D

/

E button to select the

SPECIAL

menu.

2. Press the G button and then use D

/

E button to select

Low power

.

3. Press the G button and then use

D

/

E button to select

On

or

Off

.

• When you select

On

, the screen darkens.

4. Press the ENTER button to save.

Language

Key lock

ISM Method

Low power

Set ID

Caption / Text

Captions

G

On

Off

MENU

Prev.

Owner’s Manual 19

Operation

Auto

Adjustment

- RGB (PC) mode only; this function doesn’t work for RGB-DTV mode.

- Automatically adjusts picture position and minimizes image shaking.

- After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.

-

Auto config.

and

Manual config.

are not active in DVI mode.

1. Press the MENU button and then use

D

/

E button to select the

SCREEN

menu.

2. Press the G button and then use

D

/

E button to select

Auto config.

.

3. Press the G button to run Auto configure.

• When

Auto config.

has finished,

OK

will be shown on screen.

• If the position of the image is still not correct, try Auto adjustment again.

4. In RGB (PC) mode, if the image needs to be adjusted more after using

Auto config.

, you can make further adjustments with the

Manual config.

option.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

VGA Mode

G

MENU Prev.

To set

- Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible.

- Set aspect ratios for DTV 480p, Component 480i, Video, and S-video sources.

- Use 4:3, or 16:9 for other input sources.

1. Use the ARC button repeatedly to select the desired picture format. You can also adjust

ARC

in the

SCREEN

menu.

4:3

- Choose

4:3

when you want to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides.

16:9

- Choose

16:9

when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

Horizon

- Choose

Horizon

when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view.

Zoom

- Choose

Zoom

when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.

- When enlarging or reducing the picture, the image may become distorted.

1. Use ZOOM+/ZOOM- button to enlarge or reduce the picture size.

• Zoom adjustment range is 100~300.

2. Adjust the main picture position using the

D

/

E

/

F

/

G buttons while in the enlarged picture mode.

20 Plasma Display

Zoom out

100%

F

D

G

E

Operation

Adjusting Horizontal/ V ertical Position

- This function works in the following modes:

RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i).

1. Press the MENU button and then use D

/

E button to select the

SCREEN

menu.

2. Press the

G button and then use D

/

E button to select

Position

.

3. Press the

G button and then use D

/

E

/

F

/

G button to adjust the position.

4. Press the ENTER button to save.

Auto config.

ARC

Zoom in/out

Position

Manual config.

G

Screen adj.

Reset

VGA Mode

MENU Prev.

F

D

G

E

- If the image still isn’t clear after auto adjustment and especially if characters are still jittery, adjust the picture

Phase manually.

- To correct the screen size, adjust

Clock

.

1. Press the MENU button and then use D

/

E button to select the

SCREEN

menu.

2. Press the

G button and then use D

/

E button to select

Manual config.

.

3. Press the

G button and then use D

/

E button to to select

Phase

or

Clock

.

4. Use the F

/

G button to make appropriate adjustments.

• The

Phase

adjustment range is 0 ~ 31.

• The

Clock

adjustment range is -50 ~ +50.

5. Press the ENTER button to save.

Auto config.

ARC

Zoom in/out

Position

Manual config.

G

Screen adj.

Reset

VGA Mode

MENU

Prev.

Phase 0

Clock 0

Screen Adjustments (V ideo, S-V

ideo and Component 480i mode only)

- Use this function to correct jittering or picture instability while viewing a video tape.

1. Press the MENU button and then use D

/

E button to select the

SCREEN

menu.

2. Press the

G button and then use D

/

E button to select

Screen adj.

.

3. Press the

G button and then use D

/

E button to select

TV

or

VCR

.

• Select the

VCR

option if watching a VCR.

• Select the

TV

option for other equipment. (Except VCR)

4. Press the ENTER button to save.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

YNR

G

MENU Prev.

TV

VCR

- This function operates in every mode.

- Use the Reset option to initialize the adjusted settings.

1. Press the MENU button and then use

D

/

E button to select the

SCREEN

menu.

2. Press the G button and then use

D

/

E button to select

Reset

.

3. Press the G button.

• You can initialize Zoom In/Out, Manual config., Position, Split zoom, PIP size, PIP position and sub picture size for double window.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

YNR

G

MENU Prev.

To set

Owner’s Manual 21

Operation

Luminance Noise Reduction (V

ideo, S-video and Component 480i modes only)

- Use YNR to reduce the picture noise that may appear on the screen.

1. Press the MENU button and then use

D

/

E button to select the

SCREEN

menu.

2. Press the G button and then use

D

/

E button to select

YNR

.

3. Press the G button and then use

D

/

E button to select

On

or

Off

.

4. Press the ENTER button to save.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

YNR

G

MENU Prev.

On

Off

Selecting W ide VGA mode (RGB-PC, DVI-PC mode only)

- To see a normal picture, match the resolution of RGB mode and selection of VGA mode.

- If 852x480 or 848x480 is selected, the aspect ratio is changed to 16:9 automatically.

With this setup, Double Window mode is not available.

1. Press the MENU button and then use

D

/

E button to select the

SCREEN

menu.

2. Press the G button and then use

D

/

E button to select

VGA Mode

.

3. Press the G button and then use

D

/

E button to select the desired VGA resolution.

4. Press the ENTER button to save.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

VGA Mode

G

MENU Prev.

640x480

848x480

852x480

- Enlarges the picture proportionately correct.

- Split Zoom can be used for all input sources.

- In 2-Split Zoom mode, you can only move the image up or down.

- IIf an image is enlarged, a section can be viewed without using Split Zoom.

- Split Zoom is not available if

OSD rotate

is

rotate

.

1. Press the SPLIT ZOOM button repeatedly to select either 2, 4, or 9 Split Zoom.

2-Split zoom

1

4

◀▶

4-Split zoom

1

4

2

5

◀▶

1

4

7

9-Split zoom

2

5

8

3

6

9

◀▶

2. Press the number button corresponding to the section you wish to enlarge. you can move the enlarged screen with using the D

/

E

/

F

/

G button.

9-Split zoom

1

4

7

2

5

8

3

6

9

◀▶

Example of choosing 5.

Section 5 is enlarged to fill the screen.

22 Plasma Display

Operation

PIP

(Picture-In-Picture) Feature

- PIP lets you view 2 different inputs pictures (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image.

- You can also adjust the PIP features in the PIP/DW menu (Except Swap function).

W

atching PIP

Press the PIP button repeatedly to turn PIP on or off.

Component

Video

10 : 30

PIP

Size

Press the WIN.SIZE button and then use

F

/

G button to change the sub picture size.

Win.size

F G

Press the WIN.POSITION button.

Press the D

/

E

/

F

/

G button repeatedly until desired position is achieved. The sub picture moves up/down/left/right.

You can also move the PIP position with

Win.position

in the

PIP/DW

menu.

Win.position

Press the SWAP button to exchange the main and sub pictures.

Component

Video

10 : 30

Video

Component

10 : 30

Main Picture Sub Picture

Use the PIP INPUT button to select the input source for the sub picture.

Main Picture Source

Video

S-Video

Component 480i

Component 480p/720p/1080i

RGB and DVI

Available Sub Picture Sources

S-Video, Component 480i/480p/720p/1080i, RGB and DVI

Video, Component 480i/480p/720p/1080i, RGB, and DVI

Video,S-Video, RGB, and DVI

Video and S-Video

Video, S-Video, and Component 480i,

PIP

Aspect Ratio

1. Press the MENU button and then use D

/

E button to select the

PIP/DW

menu.

2. Press the

G button and then use D

/

E button to select

PIP ARC

.

3. Press the

G button and then use D

/

E button to select

4:3

or

16:9

.

4. Press the ENTER button to save.

Input

DW

PIP

PIP Input

Win. size

Win. position

PIP ARC

G

4 : 3

16 : 9

MENU

Prev.

Owner’s Manual 23

Operation

Double W indow Setup Options

- As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time. Each source is given half the screen.

W atching Double W indow

Press the DW button repeatedly to select one of the Double Window options.

DW 1

DW 2

Sub Picture Size

Adjustment

Press the WIN.SIZE button.

• Use the

F

/

G button to change the sub picture size.

• Using the Win.size function in Double Window mode, main and sub picture sizes are changed simultaneously.

Using the Win.size function in PIP mode, sub picture size is changed.

• Win.position is not functional in Double Window mode.

Swapping the Double W

indow

Use the SWAP button to switch the main and sub pictures in Double Window mode.

Component

Video

10 : 30

Video

Component

10 : 30

Win.size

F G

Main Picture Sub Picture

Selecting a Source for the Double W

indow

Use the PIP INPUT button to select the input source for the sub picture. You can also select

PIP Input

in the

PIP/DW

menu.

Main Picture Source

Video

S-Video

Component 480i

Component 480p/720p/1080i

RGB and DVI

Available Sub Picture Sources

S-Video, Component 480i/480p/720p/1080i, RGB and DVI

Video, Component 480i/480p/720p/1080i, RGB, and DVI

Video,S-Video, RGB, and DVI

Video and S-Video

Video, S-Video, and Component 480i,

24 Plasma Display

External Control Device Setup

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally.

- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.

- RS-232C connection cables are not supplied with the Monitor.

( )

R

( ) ( )

L

( )

EXTERNAL SPEAKER

RS-232C INPUT

(CONTROL/SERVICE)

DVI INPUT

RGB INPUT

AUDIO INPUT RGB OUTPUT

EXPANDED

INPUT

R AUDIO L

Y

R

AUDIO

L (MONO)

AUDIO INPUT COMPONENT INPUT

REMOTE

CONTROL

S-VIDEO

VIDEO

INPUT

AUDIO INPUT AC INPUT

PC

T

ype of Connector; D-Sub 9-Pin Male

7

8

5

6

9

2

3

4

RXD (Receive data)

TXD (Transmit data)

DTR (DTE side ready)

GND

DSR (DCE side ready)

RTS (Ready to send)

CTS (Clear to send)

No Connection

RXD

TXD

GND

DTR

DSR

RTS

CTS

5

4

2

3

6

7

8

7-Wire Configurations

(Standard RS-232C cable)

PC PDP

4

8

7

5

6

3

2

TXD

RXD

GND

DSR

DTR

CTS

RTS

D-Sub 9

D-Sub 9

1

5

9

6

RXD

TXD

GND

DTR

DSR

RTS

CTS

5

4

2

3

6

7

8

PC

3-Wire Configurations

(Not standard)

PDP

6

7

8

5

4

3

2

TXD

RXD

GND

DTR

DSR

RTS

CTS

D-Sub 9

D-Sub 9

Owner’s Manual 25

External Control Device Setup

Use this function to specify a monitor ID number.

Refer to ‘Real Data Mapping 1’. See page 27.

1. Press the MENU button and then use

D

/

E button to select the

SPECIAL

menu.

2. Press the G button and then use

D

/

E button to select

Set ID

.

3. Press the

G button and then use

F

/

G button to adjust

Set ID

to choose the desired monitor ID number. The adjustment range of

Set ID

is 1 ~ 99.

4. Press the ENTER button to save.

• Baud rate : 115200 bps (UART)

• Data length : 8 bits

• Parity : None

* Use a crossed (reverse) cable.

• Stop bit : 1 bit

• Communication code : ASCII code

Language

Key lock

ISM Method

Low power

Set ID

Caption / Text

Captions

G

MENU Prev.

1

01. Power

02. Input Select

03. Aspect Ratio

04. Screen Mute

05. Volume Mute

06. Volume Control

07. Contrast

08. Brightness

09. Color

10. Tint

11. Sharpness

12. OSD Select

13. Remote Control Lock Mode k

14. PIP/Twin k

15. PIP Aspect Ratio

16. Split Zoom k k k k k k k k k k k k k k

17. PIP Position

18. Treble

19. Bass

20. Balance

21. Color Temperature

22. Red Adjustment

23. Green Adjustment

24. Blue Adjustment

25. PIP Input Source

26. Abnormal State

27. ISM Method

28. Low Power

29. Orbiter Time Setting

30. Orbiter Pixel Setting

31. Picture Size Setting for Double Window mode j

32. Auto Config j j j j j k k k k k k k k k k

COMMAND 1 COMMAND 2 DATA

(Hexadecimal) t r s p q y z u v w

$ t s r q o p m n l k j i g h f e c d a b u

0 ~ 3

0 ~ 64

0 ~ 64

0 ~ 64

0 ~ 3

0 ~ C8

0 ~ C8

0 ~ C8

0 ~ 4

0 ~ a

0 ~ 3

0 ~ 1

1 ~ FE

0 ~9

0 ~64

0 ~ 64

0 ~ 64

0 ~ 64

0 ~ 1

0 ~ 1

0 ~ 3

0 ~ 1

21 ~99

0 ~ 1

0 ~ 4

0 ~ 3

0 ~ 1

0 ~ 1

0 ~ 64

0 ~ 64

0 ~ 64

1

When setting the 27 ~ 32, a menu doesn’t display on screen.

26 Plasma Display

T ransmission / Receiving Protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1]: First command to control PDP set. (j or k)

* [Command 2]: Second command to control PDP set.

* [Set ID]: You can adjust the set ID to choose desired monitor

ID number in Special menu. Adjustment range is 1

~ 99. When selecting Set ID ‘0’, every connected

PDP set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal

(0x0~0x63) on transmission/receiving protocol.

* [DATA]: To transmit command data.

Transmit ‘FF’ data to read status of command.

* [Cr]: Carriage Return

ASCII code ‘0x0D’

* [ ]: ASCII code ‘space (0x20)’

OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

* The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

Error Acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x]

* The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors.

Data 1: Illegal Code

2: Not supported function

3: Wait more time

01. Power (Command2:a)

G

To control Power On/Off of the Monitor.

Transmission

[k][a][ ][Set ID][ ][Data][Cr]

Data 0 : Power Off

Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

1 : Power On

G

To show Power On/Off.

Transmission

[k][a][ ][Set ID][ ][FF][Cr]

Data 0 : Power Off

Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

1 : Power On

* In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function.

02. Input Select (Command2:b) (Main Picture Input)

G

To select input source for the Monitor.

You can also select an input source using the INPUT

SELECT button on the Monitor's remote control.

Transmission

[k][b][ ][Set ID][ ][Data][Cr]

Data 0 : RGB

1 : Component

2 : Video

3 : S-Video

4 : DVI

Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command2:c) (Main picture format)

G

To adjust the screen format.

You can also adjust the screen format using the ARC

(Aspect Ratio Control) button on remote control or in the

Screen menu.

Transmission

[k][c][ ][Set ID][ ][Data][Cr]

Data 0 : Wide screen (16:9)

1 : Normal screen (4:3)

2 : Full screen (Zoom)

3 : Horizon

Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

* Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.

External Control Device Setup

04. Screen Mute (Command2:d)

G

To select screen mute on/off.

Transmission

[k][d][ ][Set ID][ ][Data][Cr]

Data 0 : Screen mute off (Picture on)

1 : Screen mute on (Picture off)

Acknowledgement

[d][ ][Set ID][ ][OK][Data][x]

05. Volume Mute (Command2:e)

G

To control volume mute on/off.

You can also adjust mute using the MUTE button on remote control.

Transmission

[k][e][ ][Set ID][ ][Data][Cr]

Data 0 : Volume mute on (Volume off)

1 : Volume mute off (Volume on)

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x]

06. Volume Control (Command2:f)

G

To adjust volume.

You can also adjust volume with the volume buttons on remote control.

Transmission

[k][f][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

Refer to ‘Real data mapping 1’ as shown below.

Acknowledgement

[f][ ][Set ID][ ][OK][Data][x]

07. Contrast (Command2:g)

G

To adjust screen contrast.

You can also adjust contrast in the Picture menu.

Transmission

[k][g][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

Refer to ‘Real data mapping 1’ as shown below.

Acknowledgement

[g][ ][Set ID][ ][OK][Data][x]

* Real data mapping 1

0 : Step 0

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

64 : Step 100

Owner’s Manual 27

External Control Device Setup

08. Brightness (Command2:h)

G

To adjust screen brightness.

You can also adjust brightness in the Picture menu.

Transmission

[k][h][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x]

09. Color (Command2:i)

G

To adjust the screen color.

You can also adjust color in the Picture menu.

Transmission

[k][i][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x]

10. Tint (Command2:j)

G

To adjust the screen tint.

You can also adjust tint in the Picture menu.

Transmission

[k][j][ ][Set ID][ ][Data][Cr]

Data Red : 0 ~ Green : 64

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[j][ ][Set ID][ ][OK][Data][x]

11. Sharpness (Command2:k)

G

To adjust the screen sharpness.

You can also adjust sharpness in the Picture menu.

Transmission

[k][k][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x]

12. OSD Select (Command2:l)

G

To select OSD (On Screen Display) on/off.

Transmission

[k][l][ ][Set ID][ ][Data][Cr]

Data 0: OSD off 1: OSD on

Acknowledgement

[l][ ][Set ID][ ][OK][Data][x]

28 Plasma Display

13. Remote Control Lock Mode (Command2:m)

G

To lock the remote control and the front panel controls on the monitor.

Transmission

[k][m][ ][Set ID][ ][Data][Cr]

Data 0: Lock off

Acknowledgement

1: Lock on

[m][ ][Set ID][ ][OK][Data][x]

If you’re not using the remote control, use this mode.

When main power is on/off, remote control lock is released.

14. PIP / DW (Command2:n)

G

To control the PIP (Picture-in-Picture)/DW (Double Window).

You can also control the PIP/DW using the PIP or DW button on the remote control or in the PIP/DW menu.

Transmission

[k][n][ ][Set ID][ ][Data][Cr]

Data 0: PIP/DW off

1: PIP

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x]

2: DW1

3: DW2

15. PIP Aspect Ratio (Command2:o)

G

To select the PIP picture format.

You can also select the PIP picture format using WIN.SIZE

on the remote control.

Transmission

[k][o][ ][Set ID][ ][Data][Cr]

Data 0: 4:3 1: 16:9

Acknowledgement

[o][ ][Set ID][ ][OK][Data][x]

16. Split Zoom (Command2:p)

G

To operate split zoom function and select the split zoom section number.

Transmission

[k][p][ ][Set ID][ ][Data][Cr]

Data Min: 21 ~ Max:99

Refer to ‘Real data mapping 2’.

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

* Real data mapping 2

21: Selection 1 of 2 split zoom

24: Selection 4 of 2 split zoom

41: Selection 1 of 4 split zoom

42: Selection 2 of 4 split zoom

44: Selection 4 of 4 split zoom

45: Selection 5 of 4 split zoom

91: Selection 1 of 9 split zoom

99: Selection 9 of 9 split zoom

17. PIP Position (Command2:q)

G

To select sub picture position for PIP.

You can also adjust the sub picture position using

WIN.POSITION on the remote control or in the PIP/DW menu.

Transmission

[k][q][ ][Set ID][ ][Data][Cr]

Data 0: Right down on screen

1: Left down on screen

2: Left up on screen

3: Right up on screen

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

18. Treble (Command2:r)

G

To adjust treble.

You can also adjust treble in the Sound menu.

Transmission

[k][r][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

19. Bass (Command2:s)

G

To adjust bass.

You can also adjust bass in the Sound menu.

Transmission

[k][s][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

20. Balance (Command2:t)

G

To adjust balance.

You can also adjust balance in the Sound menu.

Transmission

[k][t][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

External Control Device Setup

21. Color Temperature (Command2:u)

G

To adjust color temperature.

You can also adjust ACC in the Picture menu.

Transmission

[k][u][ ][Set ID][ ][Data][Cr]

Data 0: Normal 1: Cool 2: Warm 3: User

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

22. Red Adjustment (Command2:v)

G

To adjust red in color temperature.

Transmission

[k][v][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: C8

Refer to ‘Real data mapping 3’ as shown below.

Acknowledgement

[v][ ][Set ID][ ][OK][Data][x]

23. Green Adjustment (Command2:w)

G

To adjust green in color temperature.

Transmission

[k][w][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: C8

Refer to ‘Real data mapping 3’ as shown below.

Acknowledgement

[w][ ][Set ID][ ][OK][Data][x]

24. Blue Adjustment (Command2:$)

G

To adjust blue in color temperature.

Transmission

[k][$][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: C8

Refer to ‘Real data mapping 3’ as shown below.

Acknowledgement

[$][ ][Set ID][ ][OK][Data][x]

* Real data mapping 3

0 : -20

5 : -19

A : -18

5F: -1

64: 0

69: +1

C3: +19

C8: +20

Owner’s Manual 29

External Control Device Setup

25. PIP Input Select (Command2:y)

G

To select input source for sub picture in PIP mode.

Transmission

[k][y][ ][Set ID][ ][Data][Cr]

Data 0 : RGB

1 : Component

2 : Video

3 : S-Video

4 : DVI

Acknowledgement

[y][ ][Set ID][ ][OK][Data][x]

26. Abnormal State (Command2:z)

G

To recognize an abnormal state.

Transmission

[k][z][ ][Set ID][ ][FF][Cr]

Data FF:Read

Acknowledgement

[z][ ][Set ID][ ][OK][Data][x]

Data 0: Normal (Power on and signal exist)

1: No signal (Power on)

2: Turn the monitor off by remote control

3: Turn the monitor off by sleep time function

4: Turn the monitor off by RS-232C function

5: 5V down

6: AC down

7: Turn the monitor off by fan alarm function

8: Turn the monitor off by off time function

9: Turn the monitor off by auto off function a: Turn the monitor off by AV board detect

27. ISM Method (Command2:p)

G

To avoid having a fixed image remain on screen.

Transmission

[j][p][ ][Set ID][ ][Data][Cr]

Data 0: Normal

1: White wash

Acknowledgement

2: Orbiter

3: Inversion

[p][ ][Set ID][ ][OK][Data][x]

28. Low Power (Command2:q)

G

To control the low power function on/off.

Transmission

[j][q][ ][Set ID][ ][Data][Cr]

Data 0: Low power off

1: Low power on

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

30 Plasma Display

29. Orbiter Time Setting (Command2:r)

G

To adjust orbiter operation time term.

Transmission

[j][r][ ][Set ID][ ][Data][Cr]

Data Min: 1 ~ Max: FE

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

30. Orbiter Pixel Setting (Command2:s)

G

To adjust pixel number in orbiter function.

Transmission

[j][s][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 9

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

31. Picture Size Setting for Double Window mode (Command2:t)

G

To adjust main window size in Double Window mode.

Transmission

[j][t][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64

Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

32. Auto Configure (Command2:u)

G

To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.

Transmission

[j][u][ ][Set ID][ ][Data][Cr]

Data 1: To set

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

IR Code

G

Connect your wired remote control to the Remote Control port on the Monitor.

G

Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz

T

C

Carrier frequency

T1

F

CAR

= 1/T

C

= f

OSC

/12

Duty ratio = T1/T

C

= 1/3

G

Configuration of frame

1st frame

Lead code

Low custom code

High custom code

Data code

Data code

C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat frame

Repeat code

T f

G

Lead code

G

Repeat code

9 ms 4.5 ms

0.55 ms

9 ms

2.25 ms

G

Bit description

Bit “0”

Bit “1”

0.56 ms

1.12 ms

G

Frame interval : Tf

The waveform is transmitted as long as a key is depressed.

Tf Tf

0.56 ms

2.24 ms

Tf=108ms @455KHz

Owner’s Manual 31

IR Code

Code (Hexa)

61H

63H

64H

6BH

40H

41H

69H

6AH

7BH

79H

C6H

BFH

5AH

D8H

0EH

44H

43H

52H

4DH

60H

76H

77H

AFH

99H

13H

14H

15H

16H

17H

18H

19H

0BH

98H

D5H

00H

01H

02H

03H

08H

C4H

C5H

09H

10H

11H

12H

Function

UP ( D )

DOWN ( E )

VOL+ ( G )

VOL- ( F )

POWER ON/OFF

POWER ON

POWER OFF

MUTE

Number Key 0

Number Key 1

Number Key 2

Number Key 3

Number Key 4

Number Key 5

Number Key 6

Number Key 7

Number Key 8

Number Key 9

INPUT SELECT

MULTIMEDIA

RGB

DVI

Component

Video

S-video

SLEEP

ENTER (

Á

)

MENU

DASP

APC

PIP

PIP INPUT

SWAP

PIP ARC

DW (Double window)

ZOOM +

ZOOM -

Window Size

Window Position

Split Zoom

ARC

ARC (4:3)

ARC (16:9)

ARC (Zoom)

AUTO CONFIG

Note

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button (Power On/Off)

Discrete IR Code (Only Power On)

Discrete IR Code (Only Power Off)

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button (Video/S-video/Component/RGB/DVI)

R/C Button (Component/RGB/DVI)

Discrete IR Code (Input RGB Selection)

Discrete IR Code (Input DVI Selection)

Discrete IR Code (Input Component Selection)

Discrete IR Code (Input Video Selection)

Discrete IR Code (Input S-video Selection)

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button (PIP/Double window Exchange)

R/C Button (4:3/16:9)

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button

R/C Button (4:3/16:9/Zoom mode Selection)

Discrete (Only 4:3 mode)

Discrete (Only 16:9 mode)

Discrete (Only Zoom mode)

Discrete IR Code

32 Plasma Display

Troubleshooting Checklist

T roubleshooting Checklist

No picture &

No sound

• Check whether the Monitor is turned on.

• Power cord inserted into wall outlet?

• Test the power outlet, plug another product’s power cord into the power outlet where the Monitor’s power cord was plugged in.

Picture OK &

No sound

The remote control doesn’t work

• Press the VOLUME (

G

) button.

• Sound muted? Press MUTE button.

• Check to see if there is any obstruction blocking the remote signal to Plasma

Display and the remote control causing obstruction.

• Are batteries installed with correct polarity (+ to +, - to -)?

(Refer to p.8)

• Install new batteries. (Refer to p.8)

Picture appears slowly after switching on

• This is normal, the image is muted during the plasma display startup process.

Please contact your service center, if the picture has not appeared after five minutes.

No or Poor color or Poor picture

• Select

Color

in the

PICTURE

menu and press the VOLUME ( G ) button.

(Refer to p.16)

• Keep a sufficient distance between the Monitor and the VCR.

• Activate any function to restore the brightness of the picture.

(If still picture is on the screen for more than 5 minutes, the screen gets dark.)

Horizontal/vertical bars or picture shaking

• Check for local interference such as an electrical appliance or power tool.

No output from one of the speakers

• Adjust

Balance

in the

SOUND

menu. (Refer to p.17)

Unusual sound from inside the monitor

• A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the monitor.

Owner’s Manual 33

Maintenance

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor.

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.

Please be sure not to use a wet cloth.

Extended

Absence

If you expect to leave your Monitor dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.

34 Plasma Display

MODEL

Width (Inches / mm)

Height (Inches / mm)

Depth (Inches / mm)

Weight (Pounds / kg)

Power requirement

Resolution

Colors

Temperature Operating Range

Humidity Operating Range

Maximum Elevation

P42W24Bx

40.7 / 1033

24.5 / 622

3.2 / 81

75 / 34

AC100-240V ~ 50/60Hz

852 x 480 (Dot)

16,770,000 (256 steps of each R, G and B)

32 ~ 104°F (0 ~ 40°C)

Less than 80%

6561 feet (2000m)

• The specifications shown above may be changed without notice for quality improvement.

Specification

Owner’s Manual 35

P/N : 3828VA0415D (RF03GA)

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement