INSTRUCTION MANUAL LEG PRESS OPTION FOR STRATA STRENGTH TRAINING SYSTEM QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your complete satisfaction through our authorized dealer service centers or our home office customer service department. Please call your local dealer for assistance or BodyCraft at 800-990-5556 (9:00 AM - 5:00 PM). Our trained technicians will provide immediate assistance to you, free of charge. Bodycraft is a division of Recreation Supply Inc. P.O. BOX 181 Sunbury, OH 43074 6900-LP PARTS LIST NO. DESCRIPTION QTY. 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 84A BASE CONNECTION FRONT BASE LEG PRESS SUPPORT REAR TUBE SLIDING SEAT SUPPORT FRAME SEAT SUPPORT SLIDING TUBE FOOT REST STEEL ROLLER HANDLE BAR SINGLE PULLEY BRACKET 50 ID. SQUA. END CAP 50 SQUA. END CAP RUBBER STOP RUBBER BUMPER NON-SKID PAD SPRING PIN 3/4" STEEL BUSHING 1/2" STEEL BUSHING 1/2" X 7" HEX HEAD BOLT 1/2" X 3-1/2" HEX HEAD BOLT 1/2" X 3-1/8" HEX HEAD BOLT 3/8" X 3" HEX HEAD BOLT 3/8" X 2-1/2" HEX HEAD BOLT 3/8" X 2" HEX HEAD BOLT 3/8" X 1" HEX HEAD BOLT 3/8" X 3/4" HEX HEAD BOLT 5/16" X 1/2" SETSCREW 1/2" WASHER 3/8" WASHER(LARGE) 3/8" WASHER(SMALL) 1/2" NYLON NUT 3/8" NYLON NUT LEG PRESS CABLE HOOK PULLEY SEAT BACK PAD 1" X 130 HAND GRIP OWNER'S MANUAL TOP CABLE (2890 mm) 1 1 1 1 1 2 1 1 1 1 1 1 4 15 2 1 8 1 4 8 2 2 2 4 2 3 2 2 4 12 2 18 6 9 1 1 3 1 1 2 1 1 PARTS CHART REAR TUBE(204) BASE CONNECTION(201) FRONT BASE(202) SLIDING TUBE(207) STEEL ROLLER(209) SINGLE PULLEY BRACKET(211) LEG PRESS SUPPORT(203) HANDLE BAR(210) 3/4" STEEL BUSHING(218) RUBBER STOP(214) SEAT SUPPORT(206) SLIDING SEAT SUPPORT FRAME(205) 1/2" STEEL BUSHING(219) HOOK(235) 1" x 130 HAND GRIP(239) SPRING PIN(217) PULLEY(236) FOOT REST(208) SEAT(237) BACK PAD(238) LEG-PRESS CABLE (234) (2030 mm) TOP CABLE(84A) (2890 mm) FASTENER 5/16" X 1/2" SETSCREW(228) 1/2" NYLON NUT(233) 3/8" NYLON NUT(234) 1/2" WASHER(229) 3/8" X 2-1/2" HEX HEAD BOLT(224) 1/2" X 3-1/2" HEX HEAD BOLT(221) 0" 1/2" 1" 1-1/2" 2" 3/8" WASHER(LARGE)(230) 3/8" WASHER(SMALL)(231) 2-1/2" 3" 3-1/2" 2 4" 4-1/2" 5" 5-1/2" 6" 6-1/2" 7" STEP1 1.Attach BASE CONNECTION(201) and FRONT BASE(202) to the holes in the LEFT WEIGHT BASE of Bodycraft Strata home gym using two 1/2" x 3-1/8" HEX HEAD BOLT(222), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232). 2.Attach LEG PRESS SUPPORT(203) to FRONT BASE(202) using two 3/8" x 3" HEX HEAD BOLT(223), four 3/8" WASHER(SMALL)(231) and two 3/8" NYLON NUT(232). Attach REAR TUBE(204) to LEG PRESS SUPPORT(203) as shown using two 3/8" x 3" HEX HEAD BOLT(223), four 3/8" WASHER(SMALL)(231) and two 3/8" NYLON NUT(232). 213 201 LEFT WEIGHT BASE 229 232 201 232 229 213 203 212 213 233 233 231 231 223 231 223 233 212 231 223 231 204 212 3 202 222 212 229 LEFT WEIGHT BASE STEP2 To ensure best performance, lubricate all pivot points during assembly. Insert two 3/4" STEEL BUSHING(218) and four 1/2" STEEL BUSHING(219) to SLIDING SEAT SUPPORT FRAME(205). Attach SLIDING SEAT SUPPORT FRAME(205) to LEG PRESS SUPPORT(203) as shown using two STEEL ROLLER(209) as shown. Tighten 5/16" X 1/2" SETSCREWS(228) with Hex Wrench to bolt STEEL ROLLERS (209) in place.(See FIG B) Attach eight NON-SKID PAD(216) to FOOT REST(208). Attach SEAT SUPPORT(206) to SLIDING SEAT SUPPORT FRAME(205) as shown using two 1/2" x 3-1/2" HEX HEAD BOLT(221), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232) Attach FOOT REST(208) to SLIDING SEAT SUPPORT FRAME(205) as shown using two 1/2" x 7" HEX HEAD BOLT(220), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232). 213 213 218 218 219 216 205 219 208 218 218 213 FIG B 220 229 229 232 229 232 229 228 208 228 203 205 FIG A 227 214 230 213 213 209 209 206 217 207 205 221 230 214 227 4 203 229 221 229 206 229 232 STEP3 Attach HANDLE BAR(210) and SEAT(237) to SEAT SUPPORT(206) as shown using two 3/8" X 1" HEX HEAD BOLT(226) and two 3/8" WASHER(231). Attach BACK PAD(238) on SEAT SUPPORT(206) as shown using two 3/8" x 2-1/2" HEX HEAD BOLT(224) and two WASHER(SMALL)(231). CHECK that all the parts are in assembled correctly as drawing then tighten all bolts. Attach all plastic ends caps and grips to appropriate places. 239 210 238 237 224 231 206 210 226 226 231 5 239 LEG PRESS CABLE LEG PRESS CABLE(234) If previously installed, completely remove TOP CABLE(84), along with pulleys T1, T2, T3, T4 and T5. Remove the two bolts and attach the TOP BEAM into the FRONT UPRIGHT. Assemble TOP CABLE(84A) (from leg press box) and pulleys simultaneously. Insert threaded end of TOP CABLE(84A) into slot in front of TOP BEAM, over pulleys T1, T2, around pulley T3, and over T4. Run threaded end of TOP CABLE(84A) through SINGLE PULLEY BRACKET(211) and attach pulley G1 as shown. Finish by routing TOP CABLE(84A) over pulley T5 and attach threaded end of TOP CABLE(84A) into SELECTOR ROD. For safety reasons, the threaded end should be screwed in using at least half of the available screw length. The jam nut should be tightened to SELECTOR ROD to prevent loosening. Replace the two bolts that attach the TOP BEAM to the FRONT UPRIGHT and tighten. Make certain the TOP CABLE(84A) runs above these bolts. Attach RUBBER BUMPER(215) to top of SINGLE PULLEY BRACKET(21). TOP CABLE(84A) T5T4 84A T5 80 T5 T4 84A 211 T3 90 L5 FLOATING PULLEY BLOCK(32) T1 TOP CABLE(84A) P2 T3 T3 L5 G1 84A 77 51 75 T2 T1 51 75 9 65 T2 L5 LOWER CABLE(87) 234 6 AB CABLE(86) A2 L7 LOWER CABLE(87) T3 A2 L5 L7 Screw thread end of LEG PRESS CABLE(234) into SINGLE PULLEY BRACKET(211). Attach pulleys G2 and G3, making certain LEG PRESS CABLE(234) runs beneath pulleys and is scated in pulley grooves. Attach the eyelet cable end to ADJUSTMENT TUBE(207) as shown. G1 234 G1 211 G2 201 225 231 231 G3 202 233 207 236 234 G2,G3 236 225 231 233 234 201,202 235 206 225 7 207
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021