CONTENTS - Hunter Fan
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
mounting recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
fan INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
control features:
inteli•touch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Inteli•touch troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3-Speed Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . 11
3-Speed troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
product specifications. . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
READ AND SAVE THESE INSTRUCTIONS
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the
product and proper installation; therefore, before attempting to install and operate your Casablanca
fan, read this owner’s manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electrician should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
NOTES
• The blades in each pack are matched for
equal weight to assure smooth fan operation.
If more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and
blades. Always turn the power OFF to the
ceiling fan before servicing it, working on
it, or replacing light bulbs.
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling 1-888-227-2178, or contact your local
authorized Casablanca dealer for assistance
in obtaining service.
FUSE BOX
(Remove fuse for the
circuit you will be
working on)
18″
70″
84″
CIRCUIT BREAKER
(Trip breaker for the
circuit you will be
working on)
PN 6743001 AT1008
1
MOUNTING RECOMMENDATIONS
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting
recommendations as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7’ above the floor.
• Do not locate the fan in a doorway or above a swinging door.
• In any installation, the tips of the blades must be at least 18” from the wall in order to provide sufficient
clearance for the blades.
• In bedrooms, fans work best when mounted above the foot of the bed.
• In low ceiling locations, our optional Low Ceiling Adaptor (LCA—available at
extra cost) can be used to gain 31⁄2” on certain fan models.
• Over pool tables, be sure to provide plenty of clearance to avoid damage from
pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to, or over, a pool or spa. High humidity combined
with corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52” fan even in
smaller rooms. For very large rooms, two fans may be needed.
SLOPED CEILING INSTALLATIONS
Suggested Extension Pole Lengths
Ceiling Height
Pole Length
8’
Standard
8’ 6”
Standard
9’
6”
9’ 6”
12”
10’
12”
11’
18”
12’
24”
13’
36”
14’
48”
When to Use Extension Poles
For best performance and best appearance,
an extension pole should be used with
your Casablanca fan when installing
on high (cathedral) ceilings or sloped
ceilings. Casablanca offers standard poles
in increments of 6” up to 5’. Custom poles
are available in lengths up to 10’. See
your Authorized Casablanca Dealer for
details.
Note: Fan may wobble or vibrate if
pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.
Calculation of 32°
Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.
2
Extension
Pole
maximum
hang-tru®
angle 32º
32°
blades must be
a minimum of 7′
above the floor
7′ minimum
EXAMPLE 1
This slope is less than 32˚.
It is OK to install your fan.
EXAMPLE 2
This slope is 32˚. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
EXAMPLE 3
This slope is more than 32˚.
Your fan will not hang straight down,
an adaptor is necessary. Contact your
local Authorized Casablanca Dealer in
regards to purchasing a “Slope Ceiling
Adaptor.”
Ventura ®
INSTALLATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan,
remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging
material, be certain that all parts have been removed.
Note: Only one set of blade holders is supplied. Depending on the fan model and series they will be either the
Commodore Style, the Center Style, the Badge Style with
matching badges, or the Standard Style blade holder.
perma•lock™ hardware
ALLEN SET SCREW
1
⁄4-20 x 1⁄4”
(pre-installed)
downrod & Ball
assembly
3mm
allen wrench
Fan preparation
important safety information!
motor
wires
before starting the installation of your ceiling fan, install the
threaded downrod into the motor coupling and lock the assembly
ground
wire
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly.
downrod
& Ball
assembly
Tip: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
Step B. Using the provided allen wrench, loosen the set screw
several turns to allow installation of the downrod. Thread the
downrod into the motor coupling until it stops turning, this
will take at least four and a half full turns.
Step C. Securely tighten the set screw with the provided allen
wrench to ensure safe operation of your fan.
tapered
thread
ALLEN
SET SCREW
motor
coupling
CAUTION: Failure to fully lock in the downrod before securely tightening the set screw
may cause the fan to separate from the
downrod during normal operation!
CEILING HARDWARE
additional hardware
CROSSBAR
MOUNTING
BRACKET
WIRE NUT (4)
2 1/4″ x 8-32 round head
screws (2)
1″ x 8-32 round
head screws (2)
FLAT WASHER (2)
getting started
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture
outlet box must be installed and wired.
Warning: To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box marked acceptable for ceiling fan support using the mounting
hardware provided with the outlet box.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either circuit
breaker or fuse box), lower the old fixture and disconnect
the wiring. Check the ceiling fixture outlet box to be sure
that it is marked ‘Approved for ceiling fan mounting’. If it is
not, a new box must be installed.
3
CROSSBAR MOUNTING BRACKET INSTALLATION
ceiling fan
Proceed with installation as follows:
Step 1. Route the wires from the ceiling outlet box through approved
the crossbar mounting bracket center hole. Attach the wiring box
bracket, with ground wire and ridges down, to the ceiling
fixture outlet box with the mounting hardware included with
the outlet box.
Tighten the screws firmly by hand only, being careful not to
bend the bracket by over tightening.
ceiling
wiring
ridge
side
down
crossbar
mounting
bracket
CAUTION: To reduce the risk of
personal injury, use only the
mounting hardware provided with
the approved outlet box to install
the crossbar mounting bracket.
flat
washer
green
ground
wire
approved
outlet box
hardware
CANOPY HARDWARE
CANOPY SCREW (4)
CANOPY LOCK WASHER (4)
CANOPY
HATCH
CANOPY
CANOPY INSTALLATION
Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4″ long
canopy screws and canopy lock washers.
Tighten the screw firmly by hand only.
Note: On sloped ceilings, align the
canopy opening towards the top or
room peak.
crossbar
mounting
bracket
canopy
canopy lock
washer
canopy
screw
4
Ventura ®
HANGING THE FAN
Step 3. To hang the fan body in the
canopy, hold the fan body firmly and
insert the ball into the canopy opening. Check that no wires were pinched.
Rotate the fan body until the slot in the
nylon ball fits into the pin opposite the
canopy opening.
Note: Independent control of the
light fixture using a W-80 requires
an additional power wire run from
the wall switch to the fan. See Page
11 for wiring.
CAPPED
BLUE
D1-OPTION
WIRE ON
3-SPEED ONLY
FOR INDEPENDENT
W-80 LIGHT
CONTROL
ball
slot
pin
CANOPY ELECTRICAL CONNECTIONS
PUll chain or
w-40 connections
wire nut
Step 4a. Attach the fan wires to the ceiling fixture outlet
box wiring by twisting the bare ends of the wires together
and then securing with a wire nut. Test that the connection
is secure by pulling on the wire nut. Connect in this order:
2 BLACK & BLUE
D1-OPTION WIRES
(WITHOUT W-80)
Step 4b. Pull Chain or W-40 Wiring Connections
• GREEN leads from mounting plate and fan to GROUND
conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLUE wire and BLACK power wire from fan to BLACK power
wire in ceiling outlet box. Secure with wire nut.
2 WHITE WIRES
3 GREEN WIRES
Step 4c. W-80 Wiring Connections
• GREEN leads from mounting plate and fan to GROUND
conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to RED wire from W-80 in ceiling outlet box. Secure with wire nut.
• BLUE wire from fan to YELLOW wire from W-80 in ceiling
outlet box. Secure with wire nut.
blue & yellow
WIRES
w-80 connections
black & red
WIRES
2 WHITE WIRES
NOTE: See Page 10 for additional wiring information.
3 GREEN WIRES
CANOPY HATCH INSTALLATION
Step 5. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are on
opposite sides of the canopy and all wires
are clear of the canopy opening.
Step 6. Install canopy hatch with the
last canopy screw and lock washer. To
do this, tilt the fan body away from the
hatch opening.
Tighten the screws firmly by hand only,
Step 7. Straighten the fan, then check
to ensure that there is no movement between the canopy and ceiling or Hang-Tru
ball and top support shaft.
canopy
hatch
lock
washer
canopy
screw
tilt the
fan to
install
last
canopy
screw
5
BLADE HOLDERS & HARDWARE
STANDARD STYLE
BLADE HOLDER SCREW
(2 PER BLADE)
Fiber WASHER (NOT INCLUDED IN DAMP LOCATION FANS)
BLADE SCREW
(3 PER BLADE)
STANDARD style blade holder & BLADE
Step 8. Standard Style
Attach the blades to the blade
holders with the three blade
screws and felt washers provided
for each blade.
Hand tighten securely.
BLADE SCREW
(3 PER BLADE)
BLADE HOLDER SCREW
(2 PER BLADE HOLDER)
felt washer
(3 PER BLADE)
Install the assembled blade and
blade holder to the flywheel (round
holes) or direct drive motor.
Hand tighten securely.
Repeat for each assembly.
BLADE
WARNING: To reduce the risk of personal injury, do not bend blade holders when installing,
balancing, or cleaning. Do not insert foreign objects between rotating fan blades.
Your fan is equipped with a flywheel
that allows for both 4 and 5 blade installation. The screw holes surrounded
by squares are for 4 blade installation,
while the screw holes in circles are for
5 blade installation as shown above.
6
Inteli•Touch®
INTELI•TOUCH INSTALLING THE W-32 WALL CONTROL
The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This
controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the
following precautions must be observed:
1.Use only the Casablanca W-32 wall control.
2.Do not use any additional control with your Inteli-Touch 4.No other light fixtures or electrical appliances may be
connected on the circuit controlled by the W-32 wall
fan (for example, dimmer, fan speed control, etc.).
control.
3.Do not use more than one fan per wall control.
INTELI•TOUCH SINGLE W-32 INSTALLATION
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
W-32 is used to describe either white (-11) or ivory finish.
1. Remove the screws and switch plate from the existing switch box.
2. Remove the screws holding the switch in the switch box.
3. Pull the existing switch from the switch box to expose the wire connections.
4. Remove the two wires from the switch.
5. Connect the two wires just removed from the switch to the W-32
wall control black wire and black/white stripe wire. Secure these
connections with wire nuts.
6. Connect the green ground wire coming from the back of the W-32
control to the ground wire in the switch box. Secure the splice with
a wire nut.
7. Install the W-32 in the wall box with the two long screws provided.
8. Install the wall plate with the two color matched screws.
N0TE: If wall control operation is reversed (fan switch controls lights
and light switch controls fan) turn off the power at the breaker or
fuse panel, then swap the two W-32 black/white stripe wires.
INTELI•TOUCH DUAL W-32 INSTALLATION
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
To control the fan and lights from two locations (a three-way
circuit), use 2 W-32 wall controls.
1. Remove the screws and switch plate from the existing
switch box and the screws holding the switch in the
switch box.
2. Pull the existing switch from the switch box to expose
the wire connections.
3. Determine which wire is connected to the common terminal of the 3-way switch. (The terminal will be marked
on switch).
4. Remove the wire from the common terminal of the 3-way
switch. Connect this wire to the remaining black/white
striped wire on the W-32 control. Secure this splice with
a wire nut.
5. Remove the two remaining wires from the 3-way switch.
Connect one of these wires to a black wire on the W-32
control. Secure the splice with a wire nut. The remaining
wire is to be connected to the other black wire on the
W-32. Secure the splice with a wire nut.
6. Connect the green ground wire coming from the back of
the W-32 control to the ground wire in the switch box.
Secure the splice with a wire nut.
7. Install the W-32 in the wall box with the two long screws
provided.
8. Install the wall plate with the two short color-matched
screws provided.
9. Installation of the second W-32 control is identical.
Repeat steps 1 through 7.
R
R
NOTE: If wall control operation is reversed (fan switch controls lights and
light switch controls fan) turn off the power at the breaker or fuse panel,
then swap the two W-32 black/white stripe wires.
7
R
R
Inteli•Touch®
R
INTELI•TOUCH OPERATION POWER
The POWER button is normally left in the on position. Always turn the
power off during cleaning or servicing the fan and during thunderstorms. It
is also used to exit or enter additional programs.
POWER must be left on to retain a previously set fan speed or light
level.
INTELI•TOUCH OPERATION SPEED CONTROL
There are six individual speed settings for the fan; each speed is indicated
by an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled FAN . The fan blades
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the FAN button is used. To maintain this level of speed,
FAN
turn the fan on by pressing
less than one second. To lower speed,
FAN
turn fan off, then on by pressing and holding the
button until the
desired speed is reached. When the fan is on, you may increase the speed by
pressing and holding the FAN button until the desired speed is reached,
then release it.
Fan Control
ON - OFF
A momentary press
of the FAN button
R
TO Change speed
Press and hold FAN
button longer than
one second
INTELI•TOUCH • REVERSING AIRFLOW
The direction of airflow can be changed from downward to
upward or from upward to downward.
To reverse the airflow:
FAN
1. Make sure the
is on.
2. Press the REVERSE button.
Note: A four-toned signal indicates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.
R
INTELI•TOUCH LIGHT
To turn the lights off and on, press and release the LIGHT button for less
Light Control
than one second.
To vary the light brightness:
ON - OFF
1. With lights off, press and hold the LIGHT button. After one second the
A momentary press of
lights come on at their lowest level and gradually become brighter.
the LIGHT button
2. Release the button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come
on at the same brightness the next time the LIGHT button is used. To to Change brightness
maintain this level of brightness, press the LIGHT button for less than
Press and hold
one second. To lower the brightness, turn the lights off, then press and hold
LIGHT button
the LIGHT button until the desired brightness level is reached. When the
longer than one
light is on, you may increase the brightness level by pressing and holding
second
the LIGHT button until the desired level is reached, then release it.
R
AUTOMATIC DEMONSTRATION PROGRAM
Programmed into every Inteli-Touch Series fan is an Automatic
Demonstration Program. It can be used to fully demonstrate and
test the operation of the fan.
To enter the demonstration program:
POWER off for at least three seconds. This will clear
1. Turn POWER
the fan memory ready for programming.
POWER on.
2. Turn POWER
3. Immediately operate the buttons in the following sequence:
FAN
FAN
8
+
LIGHT
+
FAN
+
LIGHT
+
FAN
A multi-tone signal will verify the start of the test program which
proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short time).
• Lights turn off.
The complete cycle lasts slightly over one minute. It will continue
POWER
to repeat until the POWER
is turned off for more than three
seconds, cancelling the program.
Inteli•Touch®
INTELI•TOUCH OPERATION LIGHT-MINDER PROGRAM
The Light-Minder program automatically turns OFF the fan mounted lights after
two hours.
To enter the Light-Minder Program:
POWER
1. Turn the POWEROFF
for at least three seconds.
2. Turn the POWER ON.
3. Immediately operate the buttons in the following sequence:
FAN
+ FAN + LIGHT + LIGHT
4. A series of tones indicates this command has been accepted.
The fan and light will operate normally using the buttons to turn them on and off.
But, if the lights are left on, they will automatically shut off after two hours. To
cancel the Light-Minder Program, turn the POWER off for three seconds.
INTELI•TOUCH OPERATION SAFE-EXIT PROGRAM
The Safe-Exit Program gives you about thirty seconds of light when you turn
the lights off, enabling you to exit your home before the lights go out.
To enter the Safe-Exit Program:
POWER off for at least three seconds.
1. Turn the POWE
POWER
2. Turn the POWE
on.
3. Immediately operate the buttons in the following sequence:
FAN + LIGHT + LIGHT
FAN +
After you hear the confirming audio
tones from the fan - immediately press
LIGHT
4. The lights will blink to indicate this command has been accepted.
The lights will stay on for twenty seconds and then begin to dim. After a total
of thirty seconds has elapsed, the lights will be off completely. To cancel the
POWER off for three seconds.
Safe-Exit Program, turn the POWE
Note: Both Light-Minder and Safe-Exit
programs can run at the same time,
however the dimmer cannot be used,
the light may only be turned ON/OFF.
INTELI•TOUCH OPERATION HOME-SAFE® PROGRAM
The Home-Safe Program makes an unoccupied home appear occupied by turning
the lights on and off at random times.
To enter the Home-Safe Program:
POWER off for at least three seconds.
1. Turn the POW
POWER on.
2. Turn the POW
3. Immediately operate the buttons in the following sequence:
LIGHT
+ FAN + LIGHT + FAN
4. A tone and flashing light indicate this command has been accepted.
This program overrides all manual control of lights and fan. The lights will now be
automatically cycled on and off in a controlled sequence as follows: On 1 hour, off
1
/2 hour, on 2 hours, off 1 hour, on 1/2 hour then off 2 hours.
This seven hour pattern will repeat continuously so that a different pattern of
lighting is seen each day of the week. POWER off for three seconds.
To cancel the Home-Safe Program, turn the POWE
INTELI•TOUCH OPERATION FAN-MINDER® PROGRAM
The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the
speed of the fan each two-hour interval to compensate for the cooling night air.
To enter the Fan-Minder Program:
POWER off for at least three seconds.
1. Turn the POWE
POWER on.
2. Turn the POWE
3. Immediately operate the buttons in the following sequence:
LIGHT + LIGHT
FAN
+ FAN + FAN
4. The fan controller will respond with three descending tones. A timer is now initiated and the fan
will reduce one speed for each two-hour interval. The fan will not, however, descend below the
second lowest speed.
POWER off for three seconds. You may increase the fan
To cancel the Fan-Minder Program, turn the POWE
FAN
speed by pressing and holding the
button until the desired speed is reached, then release
it. The fan will again reduce one speed for each 2 hour interval.
9
R
R
Inteli•Touch®
TROUBLESHOOTING
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the finish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will
damage the finish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood finish blades should be cleaned with a furniture
polishing cloth. Occasionally, a light coat of furniture polish may
be applied for added protection and beauty.
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type as
removed from the fixture. Each fan is rated for a maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
PROBLEM
INTELI•TOUCH
NO FAN OR LIGHT
POSSIBLE REMEDIES
Check main circuit fuses, curcuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
FAN WOBBLES OR SHAKES Be sure canopy pin is properly set into the slot on the ball
EXCESSIVELY
Check the screws holding the blade holders to the fan motor. Tighten as necessary.
Check the angle of the blades to make sure that a blade holder has not been bent during installation.
FAN NOISY DURING OPERATION
Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
Tighten canopy screws and mounting plate assembly.
Tighten the blade to bladeholder screws and blade holders to flywheel.
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or
have fallen off the wire splices. Tighten or adjust as necessary.
BREAK-IN PERIOD
Let fan run at high speed for two (2) hours
DOES NOT RUN ON
LOW SPEED
If new, “break-in” may be required - run at higher speed for several days
LIGHTS FLASH OR BLINK DURING OPERATION OF W-32 WALL CONTROLS/FAN MAY ROTATE OR MAKE
AUDIBLE TONES DURING OPERATION OF THE W-32 WALL CONTROLS: Normal operation.
WHEN AC POWER IS TURNED ON FOR THE FIRST TIME,THE LIGHTS OPERATE NORMALLY, BUT W-32 WALL
CONTROL OPERATION IS REVERSED: FAN BUTTON OPERATES THE LIGHTS; LIGHT BUTTON OPERATES
THE FAN: Reverse the 2 black and white striped wire connections.
FAN OR LIGHTS APPEAR TO OPERATE BY THEMSELVES (CHANGING SPEED OR INTENSITY), WALL CONTROL OPERATION IS INTERMITTENT: Check AC supply for irregularities, (noise spikes, fluctuations, or failure); or circuit
board assembly.
10
3-SPEED ♦ OPERATION
Pull-chain switches on the fan control the fan and lights. Using
the fan control pull-chain switch: Fan off at start.
First pull: fan ON, low speed
Second pull: medium speed
Third pull: high speed
Fourth pull: fan OFF
Using the optional light pull-chain switch: Light off at start.
First pull: light ON
Second pull: light OFF
Direction of blade rotation is controlled by the reverse slide switch
on the side of the switch housing.
No changes in household wiring are required.
OPTIONAL LIGHT
PULL CHAIN SWITCH
FAN & SPEED CONTROL
PULL CHAIN SWITCH
REVERSE
SWITCH
3-SPEED ♦ Optional Light Fixture Installation
NOTE: If a separate circuit is used to control the lights from a wall
control, the BLUE D1-Option wire in the canopy should be connected
to that switch leg with the BLACK fan power wire.
SWITCH HOUSING
1.Refer to light kit instructions to assemble and attach your light
kit correctly.
2.Remove the two 8-32 screws from the switch housing cap.
3.Remove the plug from switch housing.
4.Install pull-chain switch and finger tighten collar on switch.
5.Connect one wire from pull-chain switch to the BLUE D1-Option
wire. Secure splice with a wire nut.
6.Connect other wire from pull-chain switch to BLACK wire from light
kit. Secure splice with a wire nut.
7.Connect WHITE wire from switch housing to WHITE wire from light
kit. Secure splice with a wire nut.
8.At the canopy, connect the BLACK and BLUE wires.
COLLAR
3-speed Optional fan only Wall Controls
The W-40 and W-24 wall controls provide four-speed control of fan from a convenient wall location. The W-40 and W-24 are designed to replace a standard wall switch and will fit wall boxes
with a depth of 2” or greater. Not for use with single pull-chain fan/light option wiring.
3-speed Optional fan and light Wall Controls
The W-80 and W-28 wall controls provide separate control of fan and light with two separate
controls. The W-80 and W-28 are designed to replace a standard wall switch and wall boxes with
a depth of 2” or greater. Requires two hot leads from wall box to ceiling wiring box.
3-speed Optional remote Control
Add remote control convenience to Casablanca 3-Speed fans. Adapt•Touch (W-52) easily converts
new or existing Casablanca 3-speed Pull Chain fans equipped with a Hang-Tru canopy. Features
include three fan speeds, instant off, and ful-range light dimming (on models equipped with a
light fixture). The hand-held remote includes a switch plate bracket for wall mounting, and the
receiver is quickly installed in the Hang-Tru canopy. Use one Adapt•Touch to control several
fans, or purchase extra controls to operate a fan from different locacations.
11
optional 3-speed W-40 Wall Control
• The W-40 allows the choice of four
(4) different speed settings.
• No light fixture is used.
• Set the FAN pull chain switch to
the HIGH speed setting.
• No changes in household or fan
wiring are required.
• The fan may be turned ON and OFF
by the W-40 wall control.
CAUTION! Failure to set the pull-chain
speed to HIGH can result in faulty
operation of the fan and damage to
the W-40 wall control. To confirm fan
is set to HIGH: Turn W-40 fan speed
switch to ‘HI’ - set fastest fan speed
with pull chain.
R
optional W-80 Wall Control of the Fan & Light
• The fan may be turned ON and OFF
by the W-80 wall control.
• The lights may be turned ON and
OFF by the W-80 and the intensity
adjusted from low to high.
• The fan must be supplied with
two independent 120V AC supply
wires.
• Set the FAN pull chain switch to
the HIGH speed setting.
• Turn the lights ON at the fan.
• The W-80 allows the choice of four
(4) different speed settings.
CAUTION! Failure to set the pull-chain
speed to HIGH can result in faulty
operation of the fan and damage to
the W-80 wall control. To confirm fan
is set to HIGH: Turn W-80 fan speed
switch to ‘HI’ - set fastest fan speed
with pull chain.
12
Troubleshooting
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the finish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will
damage the finish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood finish blades should be cleaned with a furniture
polishing cloth. Occasionally, a light coat of furniture polish may
be applied for added protection and beauty.
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type
as removed from the fixture. Each fan is rated for a maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
Troubleshooting
3-Speed
Problempossible
remedies..
FAN WILL NOT START
•Check main circuit fuses, circuit breakers, or wall switch position.
Problem
Possible Remedies
•Check all wire connections, making sure the power is turned off during this inspection.
•Check that reverse switch is not set in center of throw.
FAN WOBBLES OR SHAKES •Be sure canopy pin is properly set into the slot on the ball.
EXCESSIVELY
•Check the screws holding the blade holders to the flywheel (or direct drive motor). Tighten as necessary.
•Check that bladeholders have not been bent during installation.
FAN NOISY DURING OPERATION
•Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s) as neccessary.
•Tighten the blade to bladeholder screws.
•Tighten canopy screws and mounting plate assembly.
•Check and tighten blade holders to flywheel (or direct drive motor).
•Make sure all screws in the motor housing are snug, but not overly tight.
•Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have fallen off the wire splices. Tighten or adjust as necessary.
BREAK-IN PERIOD
•Let fan run at high speed for two (2) hours
DOES NOT RUN ON
LOW SPEED
•If new, “break-in” may be required - run at higher speed for several days
FAN RUNS SLOWLY IN EITHER DIRECTION IF ROTATION IS STARTED BY HAND; WILL NOT REVERSE: Defective reverse switch; defective capacitor; or open motor winding: Replace reverse switch assembly; replace PCB assembly; or replace motor unit.
FAN WILL NOT OPERATE AT PROPER SPEEDS OR WILL NOT OPERATE AT ANY SPEED: Defective three-speed pull-chain switch assembly; or
defective capacitor: Replace three-speed pull-chain switch assembly; or replace PCB assembly.
For questions or to locate the nearest Casablanca Authorized Service Center call toll free:
1-888-227-2178 or visit us on the web at: www.CasablancaFanCo.com
13
Product Specifications
Model Name:
Model Number:
Ventura®
67XXD/T
Dimensions:
NOTE: Dimension B
light fixture
includes
and glass.
A =11"
B =12.5"
C = 3"
D =10.3"
E =5.6"
Weight:
19 lbs.
Motor:
Blade Span:
Blade Iron Pitch:
No. of Blades:
Technology:
XLP-2000®
42" or 50"
16°
5
3-Speed
Inteli•Touch® W-32
Airflow*:
Electricity Use*:
Airflow Efficiency*:
6,105 cfm
106 watts
57.8 cfm/watt
* Performance data is for fan only. No lighting wattage is included.
Measurements taken with 21" basic blades.
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement