4-205-400-71(1)

R

FD Trinitron

Colour Television

Instruction Manual

GB

KV-21FT1B

2000 by Sony Corporation Printed in Spain

NOTICE

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or

BSI to BS 1362 (i.e. marked with 2 or @ ) must be used.

When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

2

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

•

IMPORTANT

If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and an appropriate plug fitted in accordance with the following instructions:

The wires in this mains lead are coloured in accordance with the following code:

Blue Neutral

Brown Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green and yellow.

WARNING

• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket outlet. This plug cannot be used and should be destroyed.

• To prevent fire or shock hazard, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only.

Introduction

Thank you for choosing this Sony FD Trinitron Colour Television.

Before operating the TV, please read this manual thoroughly and retain it for future reference.

• Symbols used in the manual:

•

•

Informs you of possible hazards.

Important information

•

•

1,2...

Sequence of instructions.

•

•

K

MENU

Information on a feature.

Shaded buttons on the remote control show you the buttons you have to press to follow the sequence of the instructions.

Informs you of the result of instructions.

Safety Information

All TV’s operate on extremely high voltages. To prevent fire or electric shock, please follow the safety guidelines indicated in the blue sheet supplied.

In case of problems, have your TV serviced by qualified personnel. Never open the casing

yourself.

Table of Contents

Introduction.............................................................................................................................................. 3

Safety Information................................................................................................................................... 3

Overview

Overview of Remote Control Buttons .................................................................................................. 4

Overview of TV Buttons ........................................................................................................................ 5

Installation

Inserting Batteries into the Remote Control ........................................................................................ 5

Connecting the Aerial and VCR ........................................................................................................... 5

First Time Operation

Switching On the TV and Automatically Tuning .............................................................................. 6

Menu system

Introducing and Using the Menu System............................................................................................ 8

Menu Guide ............................................................................................................................................. 8

Teletext

............................................................................................................................................... 14

Additional Information

Connecting Optional Equipment ........................................................................................................ 15

Using Optional Equipment .................................................................................................................. 15

Specifications.......................................................................................................................................... 16

Troubleshooting..................................................................................................................................... 17

GB

Table of Contents

3

Overview of Remote Control Buttons

Muting the Sound

Press to mute TV sound. press again to restore the sound.

Displaying on Screen information

Press to display all on-screen indications. Press again to cancel.

Selecting channels

Press to select channels.

For double-digit programme numbers, e.g. 23, press -/-- first, then the buttons 2 and 3.

If you enter an incorrect first digit, this should be corrected by entering another digit (0-9) and then selecting

-/-- button again to enter the programme number of your choice.

Selecting TV mode

Press to switch off teletext or video input.

Selecting Teletext

Press to switch on teletext.

This button only works in Teletext mode.

Function associated to this button does not work with this TV.

Selecting Picture mode

Press repeatedly to change the picture mode.

Adjusting TV volume

Press to adjust the volume of the TV.

This button only works in Teletext mode.

Function associated to this button does not work with this TV.

Selecting channels

Press to select the next or previous channel.

To Temporarily Switch Off TV

Press to temporarily switch off TV (the standby indicator on TV lights up). Press again to switch on

TV from standby mode.

1

4

7

2

5

8

0

K

S

3

6

9

MENU

PROGR

RM 887

To save energy we recommend switching off completely when TV is not in use.

After 15 minutes without a signal and without any button being pressed, the TV switches automatically into standby

mode.

Selecting input source

Press repeatedly until the desired input symbol of the source appears on the TV screen.

Back to the channel last watched

Press to watch the last channel selected (watched for at least 5 seconds).

Displaying the menu system

Press to display the menu on the TV screen. Press again to remove the menu display from the TV screen.

Menu selection

•

When MENU is switched on:

Scroll Up

Scroll Down

Previous menu or selection

Next menu or selection

OK

confirms your selection

•

When MENU is switched off:

OK

Shows a channel overview.

Press or to select the channel and then, press again the

OK

button to watch the selected

channel.

Selecting Screen format

Press to view programmes in 16:9 mode. Press again to return to 4:3 mode.

Besides TV functions, all coloured buttons as well as green symbols are also used for

Teletext operation. For more details, please refer to "“Teletext” section of this instruction manual.

4

Overview

Overview of TV Buttons

Standby indicator

On/Off

switch

Video

Input jack

Audio

Input jack

Selecting

Input source

Volume control buttons

Push up the flap on the front of the TV to reveal the front control panel.

Headphone jack

Auto Start

Up Button

Programme Up or

Down Buttons (Selects

TV channels)

GB

Inserting Batteries into the Remote Control

Make sure to insert the supplied batteries using the correct polarities.

Always remember you dispose of used batteries in an environmental friendly way.

Connecting the Aerial and VCR

Connecting cables are not supplied

For more details of VCR connection, please refer to the section “Connecting Optional

Equipment” of this instruction manual.

or

OUT IN

VCR

Scart lead is optional.

Overview-Installation

5

Switching On the TV and Automatically Tuning

The first time you switch on your TV, a sequence of menu screen appear on the TV enabling you to: 1) choose the language of the menu screen, 2) choose the country in which you wish to operate the TV, 3) search and store all available channels (TV Broadcast) and 4) change the order in which the channels (TV Broadcast) appear on the screen.

However, if you need to change the language menu, change or repeat the tuning (e.g. when you move house) or rearrange again the order of the channels afterwards, you can do that by selecting the appropriate menu in the (Set Up). For more information, refer to the

“Menu Guide” section of this instruction manual. You can also do that by pressing the

Auto Start Up Button on the TV set.

1

Connect the TV plug to the mains socket (220-240V AC,

50Hz)

Press the on/off button on the TV set to turn on the TV.

The first time you press this button, a

Language

menu displays automatically on the TV screen.

2

Press the or button on the remote control to select the language, then press the

OK

button to confirm your selection. From now on all the menus will appear in the selected language.

Language

English

Español

Français

Italiano

Magyar

Nederlands

Select Language:

OK

3

The

Country

menu appears automatically on the TV screen. Press the or button to select the country in which you will operate the TV set, then press the

OK

button to confirm your selection.

Select “-“ instead of a country

• If the country in which you want to use the TV set

does not appear in the list.

• If you do not want your channels (TV Broadcast)

stored in a given channel sequence starting from

programme position 1.

Country

-

België/Belgique

France

Ireland

Luxembourg

Nederland

Select country:

OK

K

K

4

The Auto Tuning menu appears on the screen. Press the

OK

button to select

Yes

.

Do you want to start automatic tuning?

Yes

No

OK

K

continued...

6

First Time Operation

5

A new menu appears on the screen asking you to check that the aerial is connected. Ensure the aerial is connected and then press the

OK

button to start the automatic tuning.

The TV starts to automatically search and store all available channels (TV Broadcast) for you.

This procedure could take some minutes. Please be patient and do not press any button. Otherwise the automatic tuning will not be completed.

Please confirm that aerial is connected

Confirm

Searching...

OK

Auto Tuning

Programme: 01

System: B/G

Channel: C21

K

6

a)

After all available channels are captioned and stored,

Programme Sorting

menu appears automatically on the screen enabling you to change the order in which the channels appear on the screen.

If you do not wish to change the channel order, go to

Programme Sorting

Programme:

01 TVE

02 TVE2

03 TV3

04 C33

05 C27

06 C58

Select channel:

Exit:

MENU

OK

b)

If you wish to change the channel order:

1

Press the or button to select the programme number with the channel (TV Broadcast) you wish to rearrange, then press the button.

2

Press the or button to select the new programme number position for your selected channel (TV Broadcast), then press .

3

Repeat steps b)1 and b)2 if you wish to change the order of the other channels.

Programme Sorting

Programme:

01 TVE

02 TVE2

03 TV3

04 C33

05 C27

06 C58 05 C27

Select new position:

Exit:

MENU

OK

K

K

7

Press the

MENU

button to remove the menu from the

screen.

MENU

GB

Your TV is now ready for use

First Time Operation

7

Introducing and Using the Menu System

Your TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote Control to operate the menu system:

1

Press the

MENU

button to switch the first level menu on.

MENU

2

• To highlight the desired menu or option, press or

.

• To enter to the selected menu or option, press .

• To return to the last menu or option, press

• To alter settings of your selected option, press

.

/ / or .

• To confirm and store your selection, press

OK

.

3

Press the MENU button to remove the menu from the screen.

K

MENU

Menu Guide

Level 1 Level 2

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

OK

Level 3 / Function

PICTURE ADJUSTMENT

The “Picture Adjustment” menu allows you to alter the picture adjustments.

To do that: after selecting the item you want to alter press , then press repeatedly / / or to adjust it and finally press OK to store the new adjustment.

This menu also allows you to customise the picture mode based on the programme you are watching:

Personal (for individual settings).

Live (for live broadcast programmes).

Movie (for films).

• Brightness, Colour and Sharpness can only be alterated if “Personal” mode is selected.

• Hue is only available for NTSC colour signal (e.g: USA video tapes).

• Select Reset and press OK to reset the picture to the factory preset levels. continued...

8

Menu System

Level 1

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Timer

Sleep Timer: Off

On Timer: Off

OK

Level 2

Timer

Sleep Timer: Off

On Timer: i Off

OK

Level 3 / Function

SLEEP TIMER

The “Sleep Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically into the standby mode.

To do that: after selecting the option press , then press or to set the time period delay

(max. of 4 hours) and finally press OK to store.

• While watching the TV, you can press the

button on the remote control to display the

• One minute before the TV switches itself into

standby mode, the time remaining is displayed on

the TV screen automatically.

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Timer

Sleep Timer: Off

On Timer: Off

OK

Timer

Sleep Timer: Off

On Timer: Off

OK

ON TIMER

The “On Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically on from standby mode.

To do that: after selecting the option press , then press or to set the time period delay

(max. 12 hours) and press OK to store. Finally press the standby button on the remote control. After the selected length of time the TV switches on automatically.

• The standby indicator on the TV set flashes

regularly to indicate that “On Timer” is active.

• Any loss of power will cause these settings to be

cleared.

GB

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

LANGUAGE / COUNTRY

The “Language/Country” option in the “Set

Up” menu allows you to select the language that the menus are displayed in. It also allows you to select the country in which you wish to operate the TV set.

To do that: after selecting the option, press and then proceed in the same way as in the steps 2 and 3 of the section “Switching On the

TV and Automatically Tuning”.

continued...

Menu System

9

Level 1

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

OK

Level 2

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Level 3 / Function

AUTO TUNING

The “Auto Tuning” option in the “Set Up” menu allows you to automatically search for and store all available TV channels.

To do that: after selecting the option, press and then proceed in the same way as in TV steps 4 and 5 of the section “Switching On the

TV and Automatically Tuning”.

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

PROGRAMME SORTING

The “Programme Sorting” option in the “Set

Up” menu allows you to change the order in which the channels (TV Broadcast) appear on the screen.

To do that: after selecting the option, press and then proceed in the same way as in step 6 b) of the section “Switching On the TV and

Automatically Tuning”.

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Manual Programme Preset

Programme:

System:

Channel:

Label:

AFT:

Skip:

Decoder:

Confirm

01

B/G

C 21

--TVE

On

No

Off

OK

MANUAL PROGRAMME PRESET

The “Manual Programme Preset” option in the

“Set Up” menu allows you to:

a)

Preset channels or a video input source one

by one to the programme order of your

choice. To do that:

1 After selecting the ”Manual Programme

Preset” option, press then with

Programme

option highlighted press .

Press or to select on which programme number you want to preset the

channel (for VCR, select programme number

“0”). Then press .

2 After selecting the System option, press

.

Then press or to select the TV

Broadcast system (B/G for western European

countries, for France, I for United

Kingdom or D/K for eastern European countries). Then press .

continued...

10

Menu System

Level 1 Level 2 Level 3 / Function

3 After selecting the Channel option, press .

Then press or to select the channel tuning (“C” for terrestrial channels or “S” for cable channels). Next press . After that, press the number buttons to enter directly the channel number of the TV Broadcast or the channel of the VCR signal. If you do not know the channel number, press or to search for it. When you tune the desired channel, press OK twice to store.

Repeat all the above steps to tune and store more channels.

b)

Normally the automatic fine tuning (AFT) is operating, however you can manually fine tune the TV to obtain a better picture reception in the case that the picture is distorted.

To do that: while watching the channel (TV

Broadcast) you wish to fine tune, select the

AFT

option and press . Next press or to adjust the fine tuning between -15 and +15. Finally press OK twice to store.

c)

Skip any unwanted programme numbers when they are selected with the PROGR +/- buttons.

To do that: Highlighting the Programme

option, press the PROGR +/- button to select the programme number you want to skip.

When the programme you want to skip appears on the screen, select the Skip option and press . Next press or to select

Yes

. Finally press OK twice to confirm and store.

To cancel this function afterwards, select “No” instead of “Yes” in the step above.

d)

Label a channel using up to five characters.

To do that: Highlighting the Programme option, press the PROGR +/- button to select the programme number with the channel you wish to name. When the programme you want to name appears on the screen, select the Label option and press . Next press o r to select a letter, number or

“-“ for a blank. Press to confirm this character. Select the other four characters in the same way. After selecting all the characters, press OK twice to store.

continued...

Menu System

11

GB

Level 1

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Level 2

Advanced Features

Parental Lock:

Noise Reduction:

Auto Volume Ctrl.:

RGB Centring:

Picture Rotation:

Off

On

On

0

0

OK

Level 3 / Function

PARENTAL LOCK

The “Parental Lock” option in the “Advanced

Features” menu allows you to lock the buttons of the TV set. In this way after this option is selected and the TV set is switched off, the buttons on the TV do not work and the TV only works by using the remote control buttons.

To do that: after selecting the option, press .

Then press or to select On. Press OK to confirm and store and finally press on the remote control.

To cancel this function afterwards, select “Off” instead of “On” in the step above.

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Advanced Features

Parental Lock:

Noise Reduction:

Auto Volume Ctrl.:

RGB Centring:

Picture Rotation:

Off

On

On

0

0

OK

NOISE REDUCTION

The “Noise Reduction” option in the

“Advanced Features” menu allows you to reduce the picture noise in case of a weak broadcasting signal.

To do that: after selecting the option, press .

Then press or to select On. Finally press

OK

to confirm and store.

To cancel this function afterwards, select “Off” instead of “On” in the step above.

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Advanced Features

Parental Lock:

Noise Reduction:

Auto Volume Ctrl.:

RGB Centring:

Picture Rotation:

0

0

Off

On

On

OK

AUTO VOLUME CONTROL

The “Auto Volume Ctrl.” option in the

“Advanced Features” menu allows you to keep the same volume level of the channels, independent of the broadcast signal (e.g. in case of advertisement).

To do that: after selecting the option, press .

Then press o r to select On. Finally press

OK

to confirm and store.

To cancel this function afterwards, select “Off” instead of “On” in the step above.

continued...

12

Menu System

Level 1

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Level 2

Advanced Features

Parental Lock:

Noise Reduction:

Auto Volume Ctrl.:

RGB Centring:

Picture Rotation:

Off

On

On

0

0

OK

Level 3 / Function

RGB CENTRING

When connecting an RGB source, such as a

“PlayStation”, you may need to readjust the geometry of the picture. In that case, you can readjust it through the “RGB Centring” option in the “Advanced Features”.

To do that: while watching an RGB source select the “RGB Centring” option and press . Then press or to adjust the centre of the picture between –10 and +10. Finally press OK to confirm and store.

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

OK

Set Up

Language/Country

Auto Tuning

Programme Sorting

Manual Programme Preset

Advanced Features

OK

Advanced Features

Parental Lock:

Noise Reduction:

Auto Volume Ctrl.:

RGB Centring:

Picture Rotation:

Off

On

On

0

0

OK

PICTURE ROTATION

Because of the earth’s magnetism, the picture might slant. In this case, you can correct the pictures slant by using the option “Picture

Rotation” in the “Advanced Features” menu.

To do that: after selecting the option, press .

Then press or to correct any slant of the picture between -5 and +5 and finally press OK to store.

GB

Menu System

13

Teletext

Teletext is an information service transmitted by most TV stations. The index page of the teletext service (usually page 100) gives you information on how to use the service. To operate teletext, use the remote control buttons as indicated below.

Make sure to use a channel (TV Broadcast) with a strong signal, otherwise teletext errors

To Switch On Teletext :

After select the channel (TV Broadcast) which carries the teletext you wish to view, press .

To Select a Teletext page:

Input 3 digits for the page number, using the numbered buttons.

• If you have made a mistake, retype the correct page number.

• If the counter on the screen continues searching, it is because this page is not available. In that case,

input another page number

To access the next or preceding page:

Press PROGR + ( ) or PROGR - ( ).

To superimpose teletext on to the TV:

Whilst you are viewing teletext, press . Press it again to cancel teletext mode.

To freeze a teletext page:

Some teletext pages have sub-pages which follow on automatically. To stop them, press

/ . Press it again to cancel the freeze.

To reveal concealed information (e.g: answer to a quiz):

Press / . Press it again to conceal the information.

To Switch Off Teletext:

Press .

Fastext

Fastext service lets you access pages with one button push.

While you are in Teletext mode and Fastext is broadcast, a colour coded menu appears at the bottom of the teletext page. Press the colour button (red, green, yellow or blue) to access the corresponding page.

14

Teletext

Connecting Optional Equipment

Using the following instructions, you can connect a wide range of optional equipment to your TV set. (Connecting cables are not supplied).

Connecting a VCR:

To connect a VCR, please refer to the section “Connecting the aerial and VCR” of this instruction manual. We recommend you connect your VCR using a scart lead. If you do not have a scart lead, tune in the VCR test signal to TV programme number “0”. by using “Manual Programme

Preset” option. (for details how to manual programme, see page

10, step a).

Also refer to your VCR instruction manual to find out how to find the output channel of your VCR.

If you have connected a decoder to a VCR which supports

Smartlink feature:

Select the “Manual Programme Preset” option in the “Set Up” menu and after entering in the

“Decoder” option, select “On” (by using or ) to each scrambled channel.

* “PlayStation”

is a product of Sony Computer Entertainment, Inc.

* “PlayStation” is a trademark of Sony Computer Entertainment, Inc.

Using Optional Equipment

1

Connect your equipment to the designated TV socket, as indicated above.

2

To watch the picture of the connected equipment, press the button repeatedly until the correct input symbol appears on the screen.

Symbol

1

Input Signals

• Audio / video input signal through the Scart connector C

• RGB input signal through the Scart connector C. This symbol appears only if a RGB source has been connected.

2 • Video input signal through the phono socket A and Audio input signal

through

3

Switch on the connected equipment.

4

Press button on the remote control to return to the normal TV picture.

15

GB

Specifications

TV system:

B/G/H, L, I, D/K

Colour system:

PAL, SECAM

NTSC 3.58, 4.43 (only Video In)

Channel Coverage:

VHF: E2-E12

UHF: E21-E69

CATV: S1-S20

HYPER: S21-S41

L: F2-F10, B-Q, F21-F69

D/K: R1-R12, R21-R69

Picture Tube:

Flat Display FD Trinitron

Rear Terminals

:1/

21-pin scart connector input, RGB input, TV audio/ video output.

Front Terminals

…2 video input – phono jack

2 audio input – phono jack

headphones jack

Sound Output:

1 x 8 W (music power)

1 x 4 W (RMS Mono)

Power Consumption:

55 W

Standby Power Consumption:

≤

0.55 W

Dimensions (w x h x d) :

Approx. 488 x 480 x 477 mm.

Weight:

Approx. 24 Kg.

Accessories supplied:

1 Remote Control (RM-887)

2 Batteries (IEC designated)

Other features:

• Teletext, Fastext, TOPtext

• Sleep Timer

• Wake UP Timer

• Smartlink (direct link between your TV set

and a compatible VCR. For more information on Smartlink, please refer to

the Instruction Manual of your VCR).

• TV system Autodetection.

Design and specifications are subject to change without notice.

Ecological Paper- Totally Chlorine Free

16

Additional Information

Troubleshooting

Here are some simple solutions to the problems which may affect the picture and sound.

Problem

No picture (screen is dark) and no sound.

Poor or no picture (screen is dark), but good sound.

No picture or no menu information from the equipment connected to the

Scart connector.

Solution

• Check the aerial connection.

• Plug the TV in and press the button on the front of

TV.

• If the standby indicator is on, press button on

the remote control.

• Using the menu system, select the “Picture

Adjustment” menu and select “Reset” to return to the

factory settings.

• Check that the optional equipment is on and press the

button repeatedly on the remote control until the

correct input symbol is displayed on the screen.

Good picture, no sound.

No colour on colour programmes.

Distorted picture when changing programmes or selecting teletext.

Picture slanted

Noisy picture when viewing a TV channel.

Remote control does not function.

• Press the +/- button on the remote control.

• Using the menu system, select the “Picture

Adjustment” menu and select “Reset” to return to factory settings.

• Turn off any equipment connected to the Scart

connector on the rear of the TV.

• Using the menu system, select the “Picture Rotation”

option in the “Advanced Features” menu to correct the

picture slant.

• Using the menu system, select the “Manual

Programme Preset” menu and adjust Fine Tuning

(AFT) to obtain better picture reception.

• Using the menu system, select the “Noise Reduction”

option in the “Advanced Features” menu and select

“On” to reduce the noise in the picture.

• Replace the batteries.

The standby indicator on the TV flashes even though the “On Timer”

• Contact to your nearest Sony service centre.

In case of problems, have your TV serviced by qualified personnel. Never open the casing yourself.

GB

Additional Information

17

Sony España, S.A.