Baofeng UV-82 Step-by-Step Programming Guide

Baofeng UV-82 Step-by-Step Programming Guide
Baofeng UV-82 Step-by-Step Programming Guide
Also applies to UV-82HP, UV-82L, UV-82X, UV-82C, UV-89
Noji Ratzlaff
Set the radio to communicate with a repeater at 146.780– MHz, 100.0 Hz
0.
Turn on the radio and make sure it’s unlocked
1.
If the radio is in channel mode, turn off the
radio, then press and hold M ENU while
turning on the radio
2.
4.
6.
7.
Set the transm it pow er level
M ENU - 2 - M ENU - HIGH - M ENU - EXIT/AB
8.
Set the repeater offset
M ENU - 26 - M ENU - 000600 - M ENU - EXIT/AB
Set the transmit tone frequency (T-CTCS)
M ENU - 13 - M ENU - 1000 - M ENU - EXIT/AB
Set the frequency
1-4-6-7-8-0
Set the repeater shift direction (SFT-D)
M ENU - 25 - M ENU - (minus) - M ENU - EXIT/AB
Select the upper display
EXIT/AB
3.
5.
Optional : turn off the TDR (I would, at first)
M ENU - 7 - M ENU - OFF - M ENU - EXIT/AB
Your radio is now set to transm it as specified
Store the current repeater and tone settings in a memory channel
0.
Follow the procedure above to set your radio
for the frequency of your choice
1.
Clear target memory channel 37
2.
Store the frequency in channel 37
M ENU - 27 - M ENU - 37 - M ENU - EXIT/AB
Hear “receiving memory”
M ENU - 28 - M ENU - 37 - M ENU - EXIT/AB
press
%
Hear “delete channel”
M ENU - M ENU - M ENU - EXIT/AB
Hear “transm itting memory”
press
%
Now stored in m emory channel 37
Recall a stored memory setting
0.
Turn on the radio and make sure it’s unlocked
1.
If the radio is in frequency mode, turn off the
radio, then press and hold M ENU while
turning on the radio
2.
Press the up or dow n arrows or enter the
three-digit channel number (all three digits)
0-3-7
The stored channel is now ready for use
Set the radio to communicate at 147.480 MHz simplex
0.
Turn on the radio and make sure it’s unlocked
1.
If the radio is in channel mode, turn off the
radio, then press and hold M ENU while
turning on the radio
2.
3.
4.
5.
Select the upper display
Clear target memory channel 5
M ENU - 28 - M ENU - 05 - M ENU - EXIT/AB
Hear “delete channel”
8.
Store the frequency in channel 5
EXIT/AB
M ENU - 27 - M ENU - 05 - M ENU - EXIT/AB
Set the frequency
Hear “receiving memory”
1-4-7-4-8-0
press
Turn off the repeater shift direction (SFT-D)
M ENU - M ENU - M ENU - EXIT/AB
M ENU - 25 - M ENU - OFF - M ENU - EXIT/AB
Hear “transm itting memory”
Set the transm it pow er level
press
M ENU - 2 - M ENU - HIGH - M ENU - EXIT/AB
6.
7.
Optional : turn off the TDR (I would, at first)
M ENU - 7 - M ENU - OFF - M ENU - EXIT/AB
%
%
Now stored in memory channel 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement