sony chassis FE-1-32015-05-09 01:345.7 MB

SELF-DIAGNOSTIC FUNCTION

SERVICE MANUAL FE-1

CHASSIS

MODEL

COMMANDER DEST CHASSIS NO.

MODEL

COMMANDER DEST CHASSIS NO.

KV-25K5K

RM-883 OIRT SCC-Q03M-A

KV-29K5K

RM-883 OIRT SCC-Q03N-A

M I C R O F I L M

/

MENU

PROGR

RM-883

1

TRINITRON

®

COLOR TV

®

[TELEVISION SYSTEM]

B/G/H, D/K

[COLOUR SYSTEM]

PAL

SECAM

NTSC 3.58,4.43 (Video in)

[CHANNEL COVERAGE]

PAL B/G/H VHF : E2-E12, A-H2 UHF : E21-E69

CABLE TV : S1-S5, S1-S20

ITALIA VHF : A-H2 (C) UHF : 21-69

D/K VHF : R01-R12 UHF : R21-R69

[STEREO SYSTEM]

GERMAN/NICAM STEREO

[PICTURE TUBE]

KV-25K5

KV-29K5

Super Trinitron

Approx. 63cm (25 inches)

(Approx. 59cm picture measured diagonally)

110 degree deflection

Super Trinitron

Approx. 72cm (29 inches)

(Approx. 68cm picture measured diagonally)

110 degree deflection

Input/Output Terminals

[REAR]

-

-

-

21-pin Euro connector (CENELEC standard).

Inputs for Audio and Video signals.

Inputs for RGB.

Outputs of TV Video and Audio signals.

-

-

-

21-pin Euro connector.

inputs for Audio and Video signals.

inputs for S Video.

outputs for Audio and Video signals (selectable).

-

[FRONT]

Phono Jack

Outputs for Audio Signals

Sound output

Video input - phono jack

Audio inputs - phono jacks

S Video input 4 pin DIN

Headphone jacks : stereo minijack

2 x 20W (Music Power)

Power requirements 220 - 240V

Power Consumption

KV-25K5 97W

KV-29K5 108W

Dimensions

KV-25K5

KV-29K5

Approx 612x515x485mm

Approx 679x581x526mm

Weight

KV-25K5

KV-29K5

Supplied accessories

Other features

Approx 37kg

Approx 49.5kg

RM-883 Remote Commander (1)

IEC designated R6 battery (2)

FASTEXT, TOPTEXT, NICAM

[RM-883]

Remote control system infrared control

Power requirements 1.5V dc

Dimensions

Weight

2 batteries IEC designation

R6 (size AA)

Approx 65x225x21mm (w/h/d)

Approx 157g (Not including batteries)

Design and specifications are subject to change without notice.

2

Model Name

Item

Pal Comb

Velocity Modulation

DF & DQP

Woofer Box

Scart 1

Scart 2

Front in

Scart 4

Projector

AKB in 16:9 mode

Norm B/G/H

Norm I

Norm D/K

Norm AUS

Norm L

Norm SAT

Norm M

Teletext

Nicam Stereo

Language Preset

KV-25K5K

ON

OFF

OFF

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OIRT

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

KV-29K5K

ON

OFF

OFF

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OIRT

ON

ON

ON

OFF

OFF

ON

ON

OFF

The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP capacity. Should the fuse need to be replaced, use a 5 AMP FUSE approved by ASTA to BS 1362, ie one that carries the the mark.

IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE

FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT

OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED

FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH

BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE OUTLET

SOCKET.

When an alternative type of plug is used it should be fitted with a 5 AMP

FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board.

How to replace the fuse.

Open the fuse compartment with a screwdriver blade and replace the fuse.

FUSE

3

21 pin connector ( ,

2 / 2

)

15

13

11

9

7

21

19

17

5

3

1

8

6

12

10

4

2

20

18

16

14

Pin No

1

2

3

4

5

6

7

8

9

10

11

12

13

14

1 2 4 Signal

Audio output B

(right)

Audio output B

(right)

Audio output A

(left)

Ground (audio)

Ground (blue)

Audio input A

(left)

Blue input

Signal level

Standard level : 0.5V rms

Output impedence : Less than 1kohm*


Output impedence : More than 10kohm*


Output impedence : Less than 1kohm*

Function select

(AV control)


Output impedence : More than 10kohm*

0.7 +/- 3dB, 75 ohms positive

High state (9.5-12V) : Part mode

Low state (0-2V) : TV mode

Input impedence : More than 10K ohms

Input capacitance : Less than 2nF

Ground (green)

Open

Green Green signal : 0.7 +/- 3dB, 75 ohms, positive

Open

Ground (red)

Ground (blanking)

_ _ Red input 0.7 +/- 3dB, 75 ohms, positive

15

16

17

18

19

20

21

_

_

_ _

(S signal Chroma input)

Blanking input

(Ys signal)

Ground (video output)

Ground (video input)

Video output

0.3 +/- 3dB, 75 ohms, positive

High state (1-3V) Low state (0-0.4V)

Input impedence : 75 ohms

Video input

Video input

Y (S signal)

Common ground

(plug, shield)

1V +/- 3dB, 75ohms, positive sync 0.3V

(-3+10dB)


(-3+10dB)


(-3+10dB)

Pin No

1

2

3

4

Signal

Ground

Signal level

Not Connected (open) * at 20Hz - 20kHz

Y (S signal) input 1V+/- 3dB 75 ohm, positive Sync 0.3V -3/+10dB

C (S signal) input 0.3V+/- 3dB 75 ohm, positive Sync

4

Section

1. GENERAL

Title

Overview of TV buttons

Using Select Mode

Adjusting the Picture

Adjusting the Sound

Using the Sleep Timer

Viewing Teletext

Exchanging Programme Pos

Manually Tuning the TV

Fine-Tuning Channels

Using Optional Equipment

Troubleshooting

Specifications

TABLE OF CONTENTS

Page

.....................6

.....................6

.....................7

.....................7

.....................8

.....................8

.....................9

.....................9

.....................10

.....................10

.....................11

.....................11

2. DISASSEMBLY

2-1.

Rear Cover Removal

2-2.

Chassis Assy Removal

2-3.

Service Position

2-4.

H1 Board Removal

2-5.

S1 Board Removal

2-6.

Picture Tube Removal

2-7.

Removal and Replacement of the

Main - Bracket bottom plates

.....................12

.....................12

.....................13

.....................13

.....................13

.....................14

.....................15

3. SET-UP ADJUSTMENTS

3-1.

Beam Landing

3-2.

Convergence

3-3.

Screen [G2] White Balance

3-4.

Focus

.....................16

.....................17

.....................19

.....................19

Section Title

4. CIRCUIT ADJUSTMENTS

4-1.

Electrical Adjustments

4-2.

Test Mode 2

4-3.

FE-1 Self Diagnostic Software

5. DIAGRAMS

5-1.

Block Diagram

5-2.

Circuit Board Location

5-3.

Schematic Diagrams and

Printed Wiring Boards

* S1 Board

* A Board

* VM Board

* C Board

* H1 Board

5-4.

Semiconductors

5-5.

IC Blocks

6. EXPLODED VIEWS

6-1.

Chassis

6-2.

Picture Tube

7. ELECTRICAL PARTS LIST

Page

.....................20

.....................23

.....................24

.....................25

.....................32

.....................32

.....................34

.....................41

.....................46

.....................49

.....................51

.....................53

.....................55

.....................56

.....................57

.....................58

CAUTION

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE

ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE

CARBON PAINTED ON THE CRT, AFTER REMOVAL OF THE

ANODE CAP

WARNING !!

AN ISOLATING TRANSFORMER SHOULD BE USED DURING ANY

SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD DUE TO

LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY

CONNECTED TO THE POWER LINE.

SAFETY-RELATED COMPONENT WARNING !!

COMPONENTS IDENTIFIED BY SHADING AND MARKED ON

THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE

PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE

THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

ATTENTION

APRES AVOIR DECONNECTE LE CAP DE’LANODE,

COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ET

CELUI DE L’ANODE DU CAP AU CHASSIS METALLIQUE

DE L’APPAREIL, OU AU COUCHE DE CARBONE PEINTE

SUR LE TUBE CATHODIQUE OU AU BLINDAGE DU TUBE

CATHODIQUE.

ATTENTION !!

AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION PROVENANT

D’UN CHÁSSIS SOUS TENTION, UN TRANSFORMATEUR

D’ISOLEMENT DOIT ETRE UTILISÈ LORS DE TOUT DÈPANNAGE.

LE CHÁSSIS DE CE RÈCEPTEUR EST DIRECTMENT RACCORDÈ

Á L’ALIMENTATION SECTEUR.

ATTENTION AUX COMPOSANTS RELATIFS Á LA

SÈCURITÈ !!

LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNE

MARQUE SUR LES SCHÈMAS DE PRINCIPE, LES VUES

EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE

CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES

REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO

DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS

DES SUPPLÈMENTS PUBLIÈS PAR SONY.

5

Basic TV Features

Overview of TV Buttons

g

On/Off Switch.

s

MONO

2 L/G/S/I R/D/D/D

2

+ +

_

P

_ g

Video Input Button.

(selects input signals from VCR etc.).

Auto Tune

Button s

MONO

2

L/G/S/I R/D/D/D

2

+

_

+

P

_

Volume Control Buttons.

Programme Up or

Down Buttons.

(selects TV channels).

SECTION 1 GENERAL

The operating instructions mentioned here are partial abstracts from the Operating Manual. The page numbers of the Operating

Instruction Manual remain as in the manual.

Additional TV Features

Using Select Mode

You can select different preset picture and sound modes.

/

1

Press the MENU button on the remote control to display the menu on the TV screen.

SELEC T

OFF

SELEC

OFF

OK

MENU

PROGR

2

With the cursor pointing at the

SELEC T

symbol on the

TV screen as shown, press the yellow button.

3

Press the blue button to select the desired mode:

Personal Mode - reverts to settings made in

“Adjusting the Picture and Sound” sections of

the manual

Movie Mode - for films

Live Mode - for live broadcast programmes

4

Press the MENU button to remove the menu display from the TV screen.

SELEC T

OFF

Overview of Remote Control Buttons

To Mute Sound

Press to mute TV sound. Press again to restore the sound.

/

To Temporarily Switch Off TV

Press to temporarily switch off TV. Press again to switch on TV from standby mode.

To save energy we recommend switching off completely when TV is not in use.

NOTE: After 15 -30 minutes without a

TV signal and without any button being pressed, the TV switches automatically into standby mode.

To Select Channels

Press to select channels.

For double-digit programme numbers, e.g. 23, press -/-- first, then the buttons 2 and 3.

To Change Screen Format

Press to view programmes in 16:9 mode.

Press again to return to 4:3 mode.

To Adjust TV Volume

Press to adjust the volume of the TV.

MENU

PROGR

To Reveal On Screen Information

Press to reveal all on-screen indications.

Press again to cancel.

To Select Channels

Press to select channels.

RM-883

RM-883

Note:

The mode selected in step 3 is now stored.

Changing Modes Quickly

1

Press the button on the remote control to display the three different modes.

2

Press the button again to select your desired mode.

7

8


Adjusting the Picture

Although the picture is adjusted at the factory, you can modify it to suit your own requirement.

/

1

Press the button on the remote control to display the three different modes on the TV screen.

2

Press the button to highlight the personal mode symbol as shown.

3

Press the MENU button to display the menu on the TV screen.

SELEC T

MENU

PROGR

RM-883

4

Press the blue button on the control to select the

symbol on the TV screen then press the yellow button.

5

Press the blue button to select the item you wish to change (see below).

6

Press the red or yellow button to alter the selected item.

7


Symbol Item

• Contrast

• Colour

• Brightness

• Sharpness

• Hue control (only for NTSC video signals)

• Reset - resets to factory preset picture level

• Picture rotation - adjusts picture tilt

(only for KV-29C5D model)

• Represents the mode selected in the “Using

Select Mode” section.

SELEC T

OFF

OFF

IIIIIIIIIIIIIII - - - - - -





0

9

10


Adjusting the Sound

Although the sound is adjusted at the factory, you can modify it to suit your own requirement.

/

1

Press the button on the remote control to display the three different modes on the TV screen.

2

Press the button to highlight the personal mode symbol as shown.

MENU

PROGR

RM-883

3

Press the MENU button to display the menu on the TV screen.

SELEC T

OFF

4

Press the blue button to select the symbol on the

TV screen then press the yellow button.

SELEC T

OFF

5

Press the blue button to select the item you wish to change (see below).

MONO STEREO

DSP ON OFF

IIIIIIIIIIIIIIIIIIIIIII - - - - - -

IIIIIIIIIIIIIIIII - - - - - - - - -

6

Press the red or yellow button to alter the selected item.

7


Symbol

DSP

Item

• Mono sound/Stereo sound

A: Channel 1 sound/B: Channel 2 sound

(to select your desired language from a dual sound broadcast)

• On/Off (digital sound processor)

• Treble

• Bass

• Balance

• Reset (resets to factory preset sound level)

• Represents the mode selected in the “Using

Select Mode” section of the manual.


Using the Sleep Timer

The TV may be set to switch automatically to the standby mode after a length of time chosen by you. You may set the time in 15 minute steps up to 4 hours.

/

1


SELEC T

OFF

2

Press the blue button on the control to select the symbol on the TV screen, then press the yellow button.

SELEC T

OFF

SELEC

OFF

OK

MENU

3

Press the yellow button repeatedly until the required amount of time delay appears on the screen.

PROGR

RM-883

4

Once the time delay has been selected, press the

MENU button to remove the on-screen display.

One minute before standby, the display shown appears on the screen.

Notes:

• When watching TV, press the button to display time remaining.

• To return to normal operation from standby mode, press the

/

button.

SELEC

T

1:00

0:59

11

12


Viewing Teletext

Teletext is an information service transmitted by most TV stations.

/

MENU

Selecting Teletext

1

Press a number button on the remote control to select the channel which carries the teletext service you wish to receive.

2

Press the button on the remote control to switch on teletext.

TELETEXT

Index

Programme 25

News

Sport

Weather

153

101

98

3

Input three digits for the page number using the numbered buttons on the control.

4

Press the button to switch off teletext.

Note:

Teletext errors may occur if the broadcasting

signals are weak.

PROGR

RM-883

Using Other Teletext Functions

To Superimpose Teletext on to the TV

Press once in teletext mode or twice in TV mode to superimpose teletext on to the TV screen.

Press again to cancel teletext mode.

To Move to Next or Preceding Page

Press PROGR +/- on the remote control to select the previous or next page.

To Freeze a Teletext Page

Press

on the control to freeze the page.

Press again to cancel the freeze.

Revealing concealed information (eg: answers to a quiz).

Press to reveal information.

Press again to conceal the information.

Using colour buttons to access pages (Fastext)

When the colour coded menu appears at the bottom of a page, press the colour button (green, red, yellow or blue) to access the corresponding page.

TELETEXT

Index

Programme

News

Sport

Weather

25

153

101

98

TELETEXT

Index

Programme

News

Sport

Weather

25

153

101

98

TELETEXT

Index

Programme

News

Sport

Weather

25

153

101

98


Exchanging Programme Positions

After tuning you may wish to change the order in which the channels appear on the

TV. You may wish for example to exchange the channel on programme number 8 with the channel on programme number 4.

1

Press the MENU button on the remote control.

/

2

Press the blue button on the control to select on the TV screen, then press the yellow button.

SELEC T

OFF

SELEC T

OFF

MENU

3

Press the blue button to select then press the yellow button.

PROGR

C S

CH 05 IIIIIIIIIIIIIII - - - - -

F

C

OO

on

PROGR - +

01

RM-883

4

With the cursor pointing at PROGR on the TV screen as shown, press PROGR + or - button until the channel you wish to rearrange appears on screen, then press the blue button once.

5

Press the red or yellow button to select the new programme number (e.g. PROGR 04) for your selected channel.

PROGR - +

04

SELEC

OFF

OK

6

Press the blue button to select then press the yellow button to exchange the channels.

7

Repeat steps 4 to 6 if you wish to change the order of the other channels on your TV, then press

MENU to return to normal TV screen.

8

Press the PROGR+/- button to view your selected channels on their new programme numbers.

PROGR - +

04

13 14


Manually Tuning the TV

You have already tuned the TV to receive all available channels using the

`Automatically Tuning the TV' procedure at the start of this manual. You can however carry out this operation manually using the following instructions.

/

1


2


TV screen then press the yellow button.

SELEC T

OFF

SELEC T

OFF

MENU

PROGR

RM-883

3

With the cursor pointing at PROGR on the TV screen as shown, press PROGR + or - button on the remote control to allocate a programme number to the channel (eg PROGR 01). For double digit numbers e.g. 55, press the -/-- button on the remote control then the corresponding numbered buttons.

4

Press the blue button to select the channel type

(C to preset a regular channel or S to preset a cable channel) then press the yellow button to highlight the desired channel type.

5

Press the blue button to select the tuning bar scale then press the yellow or red button once to start the channel search. (Yellow to search up the scale or red to search down). When a channel is found it appears on the TV screen.

6

If you do not wish to store this channel on the programme number you selected, press the yellow or red button to continue searching for the desired channel.

7

If this is the channel you wish to store, press the blue button to select the symbol on the screen then press the yellow button to store.

8

Repeat steps 3 to 7 if you wish to store more channels then press the MENU button to remove the menu from the TV screen.

C S


F

C

OO

on

C S


F

C

OO

on

C S


F

C

OO

on

C S


F

C

OO

on

SELEC

OFF

OK


Fine-Tuning Channels

If a channel is slightly off tune, you can use this fine tune procedure to obtain a better picture reception.

/

1

With the channel you wish to fine-tune on the screen, press the MENU button on the remote control. The menu display appears on the TV screen.

SELEC T

OFF

2

Press the blue button on the remote control to select the symbol on the TV screen then press the yellow button.

SELEC T

OFF

MENU

3

Press the blue button to select the

F

symbol on the TV screen then press the red or yellow button to adjust the tuning.

SELEC

OFF

OK

C S


F

C

OO

on

PROGR

RM-883

4


TV screen then press the yellow button to store.

C S


F

C

OO

on

5

Press the MENU button to remove the menu from the TV screen.

15

Optional Connections

Using Optional Equipment

You can connect optional audio or video equipment to your TV, such as a VCR, a camcorder or video games as shown.

Select and View the Input Signal

1

Connect your equipment to the designated TV socket.

2

Press the button repeatedly on your remote control until the correct input symbol appears on the TV screen.

Symbol Input signals

1

2 s

• Audio/video input signal through the Euro AV connector

F

• RGB input signal through the Euro AV connector

F

• Audio/video input signal through the Euro AV connector

E

or the phono sockets

C

and

D

• S video input signal through the socket

B

.

3

Switch on the connected equipment.

4

To return to normal TV picture, press the control.

button on the remote

Note:

To avoid picture distortion, do not connect equipment to the

B

,

C

or

E

connectors at the same time.

Front of TV

A B C

s

D

MONO

2

L/G/S/I R/D/D/D

2

+ +

_

P

_

8mm/Hi8 camcorder

S-VHS/Hi8 camcorder

Rear of TV

Additional Information

Connecting a VCR

We recommend you tune in the VCR signal to TV programme number `0' using the `Manually Tuning in the TV' section of this instruction manual.

Connecting Headphones

Plug in your headphones to the socket

A

on the front of the TV set.

Connecting Decoders

Plug in decoders to the socket

F

on the rear of the TV.

Connecting to External Audio Equipment

Plug in your Hi-Fi equipment to the

G

sockets on the rear of the TV if you wish to amplify the audio output from the TV.

2/ s

1/

E F G

L/G/S/I

R/D/D/D

1 2

Playstation

VCR

Hi-Fi

17

18

Additional Information

Troubleshooting

Here are some simple solutions to problems which may affect the picture and sound.

Problem Solution

No picture (screen is dark), no sound • Plug the TV in.

• Press the button on the front of TV.

• If the indicator is on press

/

button or a programme number button on the remote control.

• Check the aerial connection.

• Check that the selected video source is on.

• Turn the TV off for 3 or 4 seconds and then turn it on again using the button on the front of the TV.

Poor or no picture (screen is dark), but good sound

• Using the MENU system, select the Picture

Adjustment display.

Adjust the brightness, picture and colour balance levels.

• From the Picture Adjustment display select return to the factory settings.

to

Poor picture quality when watching • Press the button repeatedly on the remote control a RGB video source.

until the RGB symbol is displayed on the screen.

Good picture, no sound • Press the +/– button on the remote control.

• If is displayed on the screen, press the button on the remote control.

No colour on colour programmes • Using the MENU system, select the Picture

Adjustment display. Adjust the colour balance.

• From the Picture Adjustment display select return to the factory settings.

to

Distorted picture when changing programmes or selecting teletext

Remote control does not function

• Turn off any equipment connected to the 21 pin

Euro connector on the rear of the TV.

• Replace the batteries.

Specifications

•

If you continue to have these problems, have your TV serviced by qualified personnel.

•

NEVER open the casing yourself.

TV system

I

Colour system

PAL

NTSC 3.58, 4.43 (only Video In)

Channel coverage

UHF: B21-B69

Picture tube

KV-25K5U:

Super Trinitron

Approx. 63 cm (25 inches) (Approx. 59 cm picture measured diagonally),

110 deflection

KV-29K5U:

Super Trinitron

Approx. 72 cm (29 inches) (Approx. 68 cm picture measured diagonally),

110 deflection

Inputs

• Rear Terminals

1

/ 21-pin Euro connector (CENELEC standard) including audio/video input, RGB input, TV audio/video output

2 / s 21-pin Euro connector (CENELEC standard) including audio/video input, S-video input, Monitor audio/video output

• Front Terminals

2 video input - phono jack s

2 audio inputs - phono jacks

S video input - 4 pin DIN

Outputs

Headphones jack - minijack stereo

Audio outputs - phono jacks

Sound output:

2 x 10 W (RMS)

Power consumption

KV-25K5U:

KV-29K5U:

139 W

158.5 W

Standby Power consumption

1 W

Dimensions (wxhxd)

KV-25K5U:

KV-295KU:

Approx. 612 x 515 x 485 mm

Approx. 679 x 581 x 526 mm

Weight

KV-25K5U:

KV-29K5U:

Approx. 37 kg

Approx. 49.5 kg

Accessories supplied

RM-883 Remote Control (1)

IEC designated batteries (2)

Other features

TELETEXT, Fastext

Design and specifications are subject to change without notice.

19

2-1. REAR COVER REMOVAL

SECTION 2

DISASSEMBLY

3 Rear Cover

2 8 Screws BTV 4x16

1 1 Screw BTV 4x16

2-2. CHASSIS ASSY REMOVAL

12

2-3. SERVICE POSITION

2-4. H1 BOARD REMOVAL 2-5. S1 BOARD REMOVAL

Release the clip indicated.

To release, push the claws in the direction of the arrow as indicated.

13

2-6. PICTURE TUBE REMOVAL

11

Two DGC holders

12

Degaussing coils

13

Spring Extension

5

Speaker box

4

Two screws

8 VM Board

(KV-29K5 only)

7

C board

9 Neck assy

(KV-29K5 only)

14

Four PT

screws (M)

6

Chassis assy

10

Deflection yolk

1 Anode cap

3

Speaker box

2

Two screws

15

Picture tube

Cushion

• REMOVAL OF ANODE-CAP

Note : Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT, after removing the anode.

* REMOVING PROCEDURES.

c a b b

•

1

2

3

1

Turn up one side of the rubber cap in the direction indicated by the arrow a

2 Using a thumb pull up the rubber cap

firmly in the direction indicated by the

arrow b

Anode button

3 When one side of the rubber cap is

separated from the anode button, the

anode-cap can be removed by turning

up the rubber cap and pulling it up in

the direction of the arrow c

HOW TO HANDLE THE ANODE-CAP

To prevent damaging the surface of the anode-cap do not use sharp materials.

Do not apply too great a pressure on the rubber, as this may cause damage to the anode connector.

A metal fitting called a shatter hook terminal is fitted inside the rubber cap.

Do not turn the rubber foot over excessively this may cause damage if the shatter hook sticks out.

14

REMOVAL AND REPLACEMENT OF THE MAIN-BRACKET

BOTTOM PLATES.

(1) REMOVING THE PLATES

In the event of servicing being required to the solder side of the A Board printed wiring board, the bottom plates fitted to the main chassis bracket require to be removed.

This is performed by cutting the gates with a sharp wire cutter at the locations shown and indicated by arrows.

Note :There are 2 plates fitted to the main bracket and secured by 4 gates.

Only remove the necessary plate to gain access to the printed wiring board.

Catch Catch

Gate Gate

£

For safety reasons, on no account should the plates be removed and not refitted after servicing.

(2) REFITTING THE PLATES

Because the plates differ in size it is important that the correct plates are refitted in their original location.

Please note that the plates need to be rotated 180 degrees from the cut position to allow the tabs to be fitted in the catch positions.

Catch

Gate

Tab

Gate

Tab

Tab

Gate

Tab

Gate

Catch

Tab

Gate

Refitting

Catch

Gate

SECTION 3

SET-UP ADJUSTMENTS

•

•

•

When complete readjustment is necessary or a new picture tube is installed, carry out the following adjustments.

Unless there are specific instructions to the contrary, carry out these adjustments with the rated power supply.

Unless there are specific instructions to the contrary, set the controls and switches to the following settings :

Contrast

Brightness

...............

...............

80% [or remote control normal]

50%

Carry out the following adjustments in this order :

3-1.

Beam Landing

3-2.

Convergence

3-4.

Focus

3-3.

White balance

Note :

Test equipment required

1.

Color bar/pattern generator.

2.

Degausser.

3.

Oscilloscope.

4.

Digital multimeter.

5.

DC Power supply.

Fig. 3-2

Purity Control

For 29" models align the neck assy as indicated below.

Preparation:

1.

In order to reduce the influence of geomagnetism on the set’s picture tube, face it in an easterly or westerly direction.

2.

Switch on the TV set’s power and degauss with the degausser.

3-1. BEAM LANDING

1.

Input an all-white signal from the pattern generator.

Set the Contrast and Brightness to normal.

2.

Set the pattern generator raster signal to all Red.

3.

Move the deflection yolk forward and adjust with the purity control so that the Red is at the centre and the Blue and Green take up equally sized areas on each side of the screen.

[See Fig.3-1 - 3-3].

4.

Move the deflection yolk forward and adjust so that the entire screen becomes Red. [See Fig.3-1].

5.

Switch the raster signal to Blue, then to Green and verify the purity condition.

6.

When the position of the deflection yolk has been determined, fasten the deflection yolk with the screws.

7.

If the beam does not land correctly in all the corners, use magnets to correct it. [See Fig.3-4].

Deflection Yoke

GREEN

RED

BLUE

A buckle

G1

G2

Neck Assy

Fig. 3-3

Purity control corrects this area.

a b

Disk magnets or rotatable disk magnets correct these areas (a - d).

Fig. 3-1

c d

Deflection yolk positioning corrects these areas.

a c b d

Fig. 3-4

16

3-2. CONVERGENCE

•

•

•

Preparation:

Before starting this adjustment, adjust the focus, horizontal size and vertical size.

Minimize the Brightness setting.

Input a dot pattern from the pattern generator.

(1) Horizontal and vertical static convergence

• Tilt the V.STAT magnet and adjust the static convergence by opening or closing the V.STAT magnet.

4.

If the V.STAT magnet is moved in the direction of the a and b arrows, the Red, Green and Blue points move as indicated below.

Centre dot

R

G

B

R

G B

V.STAT Magnet

H.STAT

C Board

RV701

SCREEN

RV702

1.

[Moving horizontally], adjust the H.STAT control so that the

Red, Green and Blue points are on top of each other at the centre of the screen.

2.

[Moving vertically], adjust the V.STAT magnet so that the

Red, Green and Blue points are on top of each other at the centre of the screen.

3.

If the H.STAT variable resistor is unable to bring the Red,

Green and Blue points together at the centre of the screen, adjust the horizontal convergence with the H.STAT variable resistor and the V.STAT magnet in the manner indicated below.

[In this case, the H.STAT variable resistor and the V.STAT

magnet influence each other].

17

(2) Operation of the BMC (Hexapole) magnet.

R G B R G B R G B

R

G

B R G B

R

G

B

V.STAT

Purity

BMC (Hexapole)

• The respective dot position resulting from moving each magnet interact, so be sure to perform adjustment whilst tracking.

Use the H.STAT VR to adjust the Red, Green and Blue dots so that they coincide at the centre of the screen

[by moving the dots in the horizontal direction].

(3) Dynamic convergence adjustment.

Preparation:

• Before starting this adjustment, adjust the horizontal and vertical static convergence.

1.

Slightly loosen the deflection yolk screws.

2.

Remove the deflection yolk spacer.

3.

Move the deflection yolk as indicated in the figure below and optimize the convergence.

4.

Tighten the deflection yolk screws.

5.

Re-install the deflection yolk spacer.

R

G

B

B

R

G

G

R

B

B

G

R

B G

R R G

B

R G B B G R

B

G

R

R G

B

B

G R

R

G

B

18

(4) Screen corner convergence.

• If you are unable to adjust the corner convergence properly, this can be corrected by the use of permalloy assemblies.

b

Permalloy d a c a-d: screen-corner convergence defect b d

Fit the permalloy assembly to the rear of the CRT to correct the area at fault.

a c

FOCUS

3-3. Screen [G2], White balance

G2 Setting

1.

Input a dot signal from the pattern generator.

2.

Set the Picture, Brightness and Colour to minimum.

3.

Apply 170Vdc from an external power supply to the

R, G and B cathodes of the CRT.

4.

Whilst watching the picture, adjust the G2 control [RV701

SCREEN] located on the C Board to the point just before the flyback return lines disappear.

White balance adjustment

1.

Input a ‘PAL’ all-white signal from the pattern generator.

2.

Enter into the Service Mode.

3.

Enter into the ‘Picture’ service menu.

4.

Select the ‘Green drive’ and adjust so that the White Balance becomes optimum.

5.

Select the ‘Blue drive’ and adjust so that the White Balance becomes optimum.

6.

Set the Picture to MIN.

7.

Set the ‘R-cut-off’ to 07.

8.

Adjust the ‘G-cut-off’, and the ‘B-cut-off’ so that the White

Balance becomes optimum.

10.

Press the button to return to TV operation.

PICTURE

R - Drive

G - Drive

B - Drive

R - cut - off

G - cut - off

B - cut - off

ID - start

ID - stop

ID - level

Bellfo

Sub Colour

Sub Brightness

Adj

Adj

02

01

Adj

Adj

Adj

Adj

01

Adj

Adj

Adj

3-4. FOCUS

1.

Input a Phillips colour pattern

2.

Set the picture settings to normal.

3.

Adjust the focus control located on the Flyback transformer to bring the centre of the screen into focus.

Note :Bring only the centre area of the screen into focus, switch to an

all-white pattern and confirm that the magenta ring is hardly noticed. To obtain optimum focus balance the focus setting between optimum screen centre focus and a reduced magenta ring level.

19

SECTION 4

CIRCUIT ADJUSTMENTS

4-1. ELECTRICAL ADJUSTMENTS

Service adjustments to this model can be performed using the supplied Remote Commander RM-883.

HOW TO ENTER INTO SERVICE MODE

1.

Turn on the main power switch and enter into the stand-by mode.

2.

Press the following sequence of buttons on the Remote

Commander.

i

+

(ON SCREEN

DISPLAY)

5

(DIGIT 5)

TEST MENU

> Picture

Geometry

Sound

TV Status

AGC Adjust

Technical

+

(VOLUME +) (TV)

• ‘TT--’ will appear in the upper right corner of the screen.

Other status information will also be displayed.

3.

Press ‘MENU’ on the remote commander to obtain the following menu on the screen.

4.

Move to the corresponding adjustment item using the ‘Green’

[up] or ‘Blue’ [down] buttons on the Remote Commander.

5.

Press the ‘Yellow’ button to enter into the required menu item.

6.

Press the ‘Menu’ button on the Remote Commander to quit the

Service Mode when all adjustments have been completed.

Note :The data shown in the ‘TV STATUS’ table is dependant on

destination and country.

PICTURE

R - Drive

G - Drive

B - Drive

R - cut - off

G - cut - off

B - cut - off

ID - start

ID - stop

ID - level

Bell-f0

Sub Colour

Sub Brightness

GEOMETRY

V centre

V size

V Lin

S Corr

H Cent

H Size

Pin Amp

Corner Pin

Pin Phase

V Bow

V Angle

Upper V Lin

Lower V Lin

Left HBLK

Right HBLK

CD Mode (AV)

SOUND

Nicam Error Lower

Nicam Error Upper

Nicam Error Rate

AGC Gain Level

TV STATUS

Destination

Text Language

A/L/E/U/D/B/K/R

East/West

Adj

Adj

02

01

Adj

Adj

Adj

Adj

01

Adj

Adj

Adj

Adj

07

07

01

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

20

80 xx

[Status only] xx

[Status only]

20

TECHNICAL

GD - Secam

BD - Secam

RC - Secam

GC - Secam

BC - Secam

GD - Sports

BD - Sports

RC - Sports

GC - Sports

BC - Sports

Y - Delay (AV)

10

30

36

14

30

31

11

19

15

17

07

SUB BRIGHTNESS ADJUSTMENT

1.

Input a Phillips colour pattern.

2.

Press ‘TEST’ ‘TEST’ 13 on the Remote Commander.

3.

Adjust the ‘Sub-Brightness’ data so that there is barely a difference between the 0 IRE and 10 IRE signal levels.

SUB CONTRAST ADJUSTMENT

1.

Input a video signal that contains a small 100% white area on a black background

2.

Set the picture control to maximum. [‘TT01’]

3.

Connect an oscilloscope to Pin 1 of CN504 [A Board].

4.


5.

Adjust the ‘R - Drive’ data to obtain the following waveform.

Note: Ensure that no signal is applied to the Antenna socket while

carrying out the following IF adjustments.

SYSTEM B/G, D/K, I & L I.F ADJUSTMENT

1.

Input a 38.9Mhz carrier signal at 100dBuV to Pin 11 [IF output] of the tuner [TU101].

2.

Measure the voltage at Pin 17 of [IC101].

3.

Adjust L103 [A Board] to obtain a voltage of 2.5V +/- 0.3V.

SYSTEM L BAND 1 I.F ADJUSTMENT

1.

Input a 34.0MHz carrier signal at 100dBuV to Pin 11 [IF output] of the tuner [TU101].

2.

Select ‘system L’ + C00 [channel 00].

3.

Measure the voltage at Pin 17 [IC101].

4.

Adjust RV101 [A Board] to obtain a voltage of 2.5V +/- 0.3V.

TUNER AGC ADJUSTMENT

1.

Receive a signal of 65dBuV / 75 ohm terminated, via the tuner antenna socket.

2.

Connect a voltmeter to JW130 [A Board].

3.

Enter into the ‘Test Menu’.

4.

Select the ‘AGC Adjust’ menu item.

5.

Adjust the data using the Yellow and Green buttons on the

Remote Commander to obtain a voltage of 3.0V +/- 0.2V.

A

25" 2.21V +/- 0.01V

29" 2.52V +/- 0.01V

R - out Waveform

SUB COLOUR ADJUSTMENT

1.

Receive a PAL colour bar signal.

2.

Connect an oscilloscope to Pin 3 of CN504 [A Board].

3.


4.

Adjust the ‘Sub Colour’ data so that the Cyan, Magenta and

Blue colour bars are of equal levels as indicated below.

RV101

L103

17

IC101

11

JW130

TUNER

Same Level

A Board component side

B-Out Waveform

21

BELL FILTER ADJUSTMENT (

Secam models only

).

Note : Ensure that the TV set has been powered up for at least

1 minute to allow for drift before carrying out the following adjustment.

1.

Input a video SECAM Colour Bar signal via AV1.

2.

Connect an oscilloscope to pin 1 of CN504 [R-OUT] on the

A board.

3.

Enter into the ‘Picture’ menu and select ‘Bell-f0’.

4.

Decrease the register of ‘Bell-f0’ until the following waveform change between RED and BLUE is obtained.

Before adjustment After adjustment

5.

When the correct waveform has been obtained add an additional 7 steps to the register.

DEFLECTION SYSTEM ADJUSTMENT

1.

Enter into the ‘Geometry’ service menu.

2.

Select and adjust each item in order to obtain the optimum image.

GEOMETRY

V centre

V size

V Lin

S Corr

H Cent

H Size

Pin Amp

Corner Pin

Pin Phase

V Bow

V Angle

Upper V Lin

Lower V Lin

Left HBLK

Right HBLK

CD Mode (AV)

Adj

07

07

01

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

Adj

22

V SIZE

V LIN

S CORRECTION

V CENTRE

H CENTRE

H SIZE

PIN AMP

PIN PHASE

CORNER PIN

V ANGLE

4-2. TEST MODE 2:

Is available by pressing ‘TEST’ button twice, OSD ‘TT’ appears. The functions described below are available by pressing the two numbers. To release the Test mode 2, press 0 twice, or switch the TV into stand-by mode, or press the TV button on the remote commander.

28

29

30

31

24

25

26

27

20

21

22

23

16

17

18

19

36

37

38

39

32

33

34

35

40

41

12

13

14

15

08

09

10

11

04

05

06

07

00

01

02

03

Cancel Test mode

Picture maximum

Picture minimum

Volume 35%

Volume 50%

Volume 65%

Volume 80%

Ageing mode On/Off

Set shipping conditions

Display TV Status

No function

Sub Picture Adjustment

Sub Colour Adjustment

Sub Brightness Adjustment

Text H position Adjustment

Rotation test

Picture level 50%

Audio mute ON

Disable Blanking

No function

No function

Destination A

Destination L

Destination E

Destination U

Destination D

Destination B

Destination K

Destination R

No function

No function

Auto shutoff Disable/Enable

RGB priority Disable/Enable

Rotation On/OFF

Text language East/West

Wide CRT/4:3 CRT

VM ON/OFF test

No function

No function

No function

No function

Re-initialize the NVM [Only when Prog=59]

62

63

64

65

58

59

60

61

66

67

68 -100

54

55

56

57

50

51

52

53

46

47

48

49

42

43

44

45

Re-initialise geometry settings [Only when Prog=59]

No function

No function

No function

No function

No function

Set NVM as NON Virgin [Only when Prog=59]

Set NVM as Virgin [Only when Prog=59]

No function

No function

No function

No function

No function

No function

No function

No function

No function

No function

No function

Auto AGC Adjust

Alternative Dest B Autotuning

Enable/Disable Y/C input

Signal Quality Check for Auto Tune

Signal Quality NOT Checked for Auto Tune

No function

Manual AGC Adjust

No function

23

4-3. FE-1 SELF DIAGNOSTIC SOFTWARE

The identification of errors within the FE-1 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must be counted) See Table 1., non fatal errors are reported using this method.

Each time the software detects an error it is stored within the NVM. See Table 2.

How to enter into Table 2

1.

Turn on the main power switch of the TV set and enter into the

‘Standby Mode’.

2.

Press the following sequence of buttons on the Remote

Commander.

Table 1

ERROR

No error

Not allowed (may be confused with Sircs response flash!)

Protection circuit trip < ANY TIME >

Reserved

No vertical sync

AKB

IIC bus clock and/or data lines low at Power ON

NVM no IIC bus acknowledge at Power ON

Jungle controller no IIC acknowledge at Power ON

Tuner no acknowledge at Power ON

Sound processor no acknowledge at Power ON

LED

ERROR

COUNT

00

01

06

07

08

09

10

02

03

04

05

Flash Timing Example : e.g. error number 3

StBy LED

ON ON ON i +

(ON SCREEN

DISPLAY)

5

(DIGIT 5) (VOLUME -) (TV)

3.

The following table will be displayed indicating the error count.

Table 2

Error Times

2 -

3 -

4 -

5 -

6 -

7 -

8 -

9 -

10 -

OFF OFF

Note: To clear the error count data press ‘80’ on the Remote

commander.

24

5-1 BLOCK DIAGRAMS (1)

YC JUNGLE VIF DECODER

TU101

IF1

AGC

SCL

TO H BOARD

CN907

SDA

CN007

KEY

4

RESP

6

KEY

RESP

SIRCS

7

SIRCS

CN001

AGC

5

2

SCLI

3

SDAI

4

CS

SCLI

SDAI

BUFFER

Q107

CN505

6

NS CORRECT

TO

VM BOARD

CN1705

VM OUT

5

TO

H BOARD

CN906

CN406

AUDIO L

8

AUDIO R

6

Y/CVBS

4

C

2

AUDIO L

AUDIO R

Y/CVBS

C

SWF

101

SWF

102

BUFFER

Q013

29" only

IC101 VIF/SIF

DEMODULATOR

AF OUT

8

QSS 12

DET OUT

16

1

2

VIF

VIF

23

24

SIF

SIF

14 TU AGC

7

LIL SW

STAND SW RF

3

AGC

AFC

22

17

BUFFER

Q101

STBY 5V

IC005 SWITCH SCART

MATRIX

O-KEY/SCART 13

I-KEY/SCART 9

14 I-KEY

12 I-KEY

I-KEY/SCART 1/2 10

I MODE 1 15

I MODE 2 11

VIDEO AMP

Q408, 409

SYNC SEP

Q005, 004

IC001

MICRO CONTROLLER

8

0-COIN

0-MSP/ASW

3

21

4

9

BE/DK/I

0-RFAGC

I-AFT

0-V BLK

17

BUFFER

Q012

SWITCH

Q006

0- +B DROP 18

0-VOL 2

10

AGC MON

14 AGC DEFEAT

0-SP MUTE 30

15 0-BAND-M

16

0-BAND-L

20

0-BAND-L

OSD BLK 35

11 I-KEY-SCART

6

0-KEY SCART

12 0-SCART 1/2

R

G

34

33

B 32

19

0-LED

48 I-PROCDES

0-WP

7

IC003 RESET

1

X001

12MHZ

43 RESET

EXT CVBS 24

1 0-ROT/VC

0-XRAY PROT 52

0-STBY 51

5 D-N-C

HP

36

42 X-OUT

VP

37

41 X-IN

MON OUT

7

8

AMPLIFIER

Q007,008,

009

IC004

NVM

SWITCH

Q011

IC301

Y/C JUNGLE

29 INT BLK

6

SCLO

SDAO

5

32 INT R2 IN

31 INT G2 IN

30 INT B2 IN

SDA

SCL

35

SDAO

34

SCLO

MON OUT 6

18

HP

PROTECT

EXT B IN

26

EXT G IN

27

EXT R IN 28

EXT BLK

25

Y/CVBS IN 41

43 TV/C2 IN

ABL IN

3

EW

11

VD+

13

VD14

15 VM OUT

48

XTAL 1

47

2

XTAL 2

CI IN

4

Y1/CVBS IN

HD 19

R OUT

22

G OUT

23

B OUT

24

IK IN

21

MON OUT

ABL

EW

VD+

VD-

HD

IC201

AUDIO AMP

5

L IN/IN 2

9

STBY

3 VOLUME

VAR/L

MON OUT

R IN/IN 3

4

1

L OUT/NC

12

2 VAR R/SW

10

MUTE

R OUT/OUT

14

NC/IN 2 6

HD

SCL

SDA

4

1

CN201

R AUDIO

TO SPEAKERS

L AUDIO

CN208

2

4

1

5

1

L AUDIO

IN

R AUDIO

IN

L AUDIO

OUT

TO H1

BOARD

CN908

R AUDIO

OUT

CN101

SCL

2

SDA

5

SIF

4

RST

6

9

10

MONO

R1

L1

TO S1

BOARD

CN1101

11

R2

12

L2

14

TVR OUT

15

16

TVL OUT

17

R AUDIO OUT

L AUDIO OUT

DGC

CN606

TO H1

BOARD

CN604

CN603

CN602

1

2

1

2

1

3

DGC

CHECK

DGC CHECK

DGC

DGC

LINE FILTER

T601

J404

RELAY

RY601

RELAY

SWITCH

Q601

J401

A6

A2

L AUDIO IN

L AUDIO IN

A1

DET R OUT

B1

B3

A3

MON R OUT

MON L OUT

DET L OUT

A19

DET V OUT

B8

MODE

A8

MODE

A7

BLUE

A11

GREEN

A15

RED

A16

BLK

A20

V IN

B2

AUDIO R IN

B6

AUDIO L IN

B15

C IN

B20

YV IN

5

D632

RECT

7

T602

2

1

4

3

MAIN RECT

D601

5 C

4

D

IC609

STANDBY

POWER

IC606

POWER

FBO CP

1

VCC 4

D

3

S

2

HD

3

4

PH601

ISOLATOR

2

1

+B

IC501

V OUTPUT

VD+

7

IN

VP

3

BOOST

VD-

1 REF

OUT

5

V- DY+

V- DY-

H- DY-

H- DY-

H- DY+

H- DY+

6

3

2

1

5

4

DY ASSY

V- DY+

V- DY-

H- DY-

H- DY+

H-DRIVE

Q535

7

8

3

4

5

T603

SRT

MUTE SW

Q202

13

14

15

16

11

12

D605

+B RECT

D614

RECT

D610

RECT

1

IC603

ERROR AMP

2

+B

AUDIO

VCC

1

IC604

5VREG 3

+5V

1

IC605

9VREG

3 +9V

EW

HP

PROTECT

3

2

5

6

IC531

PIN CORRECTION

-

+

7

+

-

1

PIN OUT

Q532

T801

FBT

LOW B

IC608

5V REG

STBY

+5V

HP

+B

D571,

Q571,574

1

4

3

5

6

T531

HDT

H-OUT

Q533

HV

D511

CN502

1

1000V

2

200V

4

H1

TO C BOARD

CN701

TO PICTURE

TUBE

FV

13

12

11

ABL

10

D513

+15V RECT

9

8

DF 1

CN509

TO VM BOARD

CN1809

29" only

1

CN503

29" only

TO VM BOARD

CN1803

7

D514

-15V RECT

-15V

V DY

H DY

CN504

1

2

3

RED

GREEN

BLUE

6

IK

TO C BOARD

CN703

25 26 27 28

5-1 BLOCK DIAGRAMS (2)

TO A BOARD

CN505

CN1705

7

6

5

V PULSE

NS CORRECT

VM

+9V

+9V

5

6

2

IC1901

COMPARATOR

+

3 -

1

-

+

7

2

3

6

5

IC1801

ROTATION

AMP

-

+

+

-

7

1

29” models only

CN1803

TO A BOARD

CN503

1 15V PULSE

VM AMP

Q1701, 1702,

1708, 1709,1710

VM AMP

BUFFER

Q1704

BUFFER

Q1840,

1841

+9V

2

3

IC1902

DF COMPARATOR

-

+

1

5

6

+

-

7

VM OUT

Q1703,1706

ROTATION AMP

ROT +

ROT -

1

CN1801

TO ROTATION

COIL

3

CN1101

SCL

1

SDA

2

SIF

5

6

MONO

TO A BOARD

CN101

R1

L1

10

11

R2

12

L2

14

TVR OUT

9

15

TVL OUT

16

R AUDIO OUT

17

L AUDIO

OUT

S1

(STEREO DECODER)

4 SCL

5 SDA

1 2

SIFI

2 9

MONO IN

3 3

3 4

3 6

3 7

SCART 1 IN

R

SCART 1 IN

L

SCART 2 IN

R

SCART 2 IN

L

IC1101

STEREO DECODER

XTAI OUT

XTAI IN

1 7

1 8

SCART 1 OUT

SCART 1 OUT

MAIN OUT R

MAIN OUT L

4 7

TVR OUT

4 8

TVL OUT

6 0

AUDIO R OUT

6 1

AUDIO L OUT

TVR OUT

TVL OUT

AUDIO R OUT

AUDIO L OUT

T1901

DF

VM

GND

QP+

QP-

6

8

2

4

NECK ASSY

VM

QP

QP

1

CN1809

TO A BOARD

CN509

TO A BOARD

CN504

CN703

3

6

1

2

R

G

B

CUT OFF

R DRIVE, BKG

Q702, 703

G DRIVE, BKG

Q705, 706

B DRIVE, BKG

Q708, 709

TO A BOARD

CN502

CN701

1

2

6

H2

G2

+200V

D711

PROTECT

C

(RGB OUT)

RV702

H STAT

R OUT

Q704

G OUT

Q 707

B OUT

Q710

RV701

SCREEN

G2

(1000V)

H1

H2

RCV

G2

R

G

B

PICTURE TUBE

H

R

C

V

G

2

G

4

H

V

TO A BOARD

T511 (FBT)

TO A BOARD

CN007

CN603

1

2

CN907

KEY

4

RESP

6

SIRCS

7

TO A BOARD

CN208

CN908

AUDIO L

OUT

2

1

AUDIO L IN

5

AUDIO R IN

AUDIO R

OUT

4

TO A BOARD

CN406

CN906

AUDIO L

2

4

AUDIO R

Y/CVBS

6

C

8

S601

P O W E R

F U N C T I O N

S W I T C H

S 9 0 0 - S 9 0 2

2

1

R E M O T E

C O N T R O L

R E C E I V E R

I C 9 0 0

RECEIVER, FUNCTION SWITCH

1

CN604

2

TO A BOARD

CN606

CN900

3

1

4

2

L

R

V I D E O

Y/C

J900

H E A D P H O N E S

29 30 31

5-2. CIRCUIT BOARD LOCATION

C Board

VM Board

29” only

S1 Board

H1 Board

A Board

•

•

•

•

5-3. SCHEMATIC DIAGRAMS AND

PRINTED WIRING BOARDS

Note :

• All capacitors are in µF unless otherwise noted.

• pF : µµF 50WV or less are not indicated except for electrolytic types.

• Indication of resistance, which does not have one for rating electrical power, is as follows.

•

•

•

•

Pitch : 5mm

Electrical power rating : 1/4W

• Chip resistors are 1/10W

• All resistors are in ohms.

k = 1000 ohms, M = 1000,000 ohms

: nonflammable resistor.

: fusible resistor.

: internal component.

: panel designation or adjustment for repair.

• All variable and adjustable resistors have characteristic curve B, unless otherwise noted.

• All voltages are in Volts.

• Readings are taken with a 10Mohm digital mutimeter.

• Readings are taken with a color bar input signal.

• Voltage variations may be noted due to normal production tolerences.

• : B + bus.

: B - bus.

: RF signal path.

: earth - ground.

: earth - chassis.

Reference Information

RESISTOR RN

RC

FPRD

FUSE

RS

RB

RW

COIL LF-8L

CAPACITOR TA

PS

PP

PT

MPS

MPP

ALB

ALT

ALR

: METAL FILM

: SOLID

: NON FLAMMABLE CARBON

: NON FLAMMABLE FUSIBLE

: NON FLAMMABLE METAL OXIDE

: NON FLAMMABLE CEMENT

: NON FLAMMABLE WIREWOUND

: ADJUSTMENT RESISTOR

: MICRO INDUCTOR

: TANTALUM

: STYROL

: POLYPROPYLENE

: MYLAR

: METALIZED POLYESTER

: METALIZED POLYPROPYLENE

: BIPOLAR

: HIGH TEMPERATURE

: HIGH RIPPLE

Note: The components identified by shading and marked

£

are critical for safety

Replace only with the part numbers specified in the parts list.

Note:

Les composants identifies par une trame et critique pour le securite. Ne les remplacer que par des pieces de numero specifie.

32

WAVEFORMS A BOARD

1 PAL 1 SECAM 2 PAL 2 SECAM 3

4

1.0 Vp-p (H)

5

1.3 Vp-p (H)

6

1.0 Vp-p (H)

7

1.3 Vp-p (H)

8

2.6 Vp-p (H)

9

2.6 Vp-p (H)

10

0.5 Vp-p (H)

11

5.0 Vp-p (H)

12

1.4 Vp-p (H)

13

2.0 Vp-p (H)

56 Vp-p (V) 290 Vp-p (H)

14

146 Vp-p (V) 12 Vp-p (H)

15 PAL

142 Vp-p (H)

15 SECAM

1.1KVp-p (H) 2.4 Vp-p (H) 3.0 Vp-p (H)

WAVEFORMS C BOARD

1 2

3

102 Vp-p (H)

4

95 Vp-p (H)

93 Vp-p (H) 24 Vp-p (H)

5-4 SEMICONDUCTORS

STR-F6654 CD4052BCM

16 9

1

(TOP VIEW)

8

LM358DR-EZ

NJM4558M-TE2

NJM2903D

8 5

1

5

STV9379

1 4

( TOP VIEW )

LM393P

TDA2822M

TEA2124

8 7 6 5

1 2 3 4

( TOP VIEW )

SAA5497PS/MIA/038

SAA5497PS/MIA/039

SAA5497PS/MIA040

52 27

1

3

2

5

4

7

6

ST24W08FM6TR

8 5

1

( TOP VIEW )

4

TDA9875

TDA9870

64

BF421-AMMO

2SA1091-O

1

( TOP VIEW )

SBX1981-51

26

TDA7495

1

15

SE-135N

SE135N-LF12

TDA9818-V1

TDA9817-V1

24 13

E

C

B

2SC688-LK

32

2SA1837

1

( TOP VIEW )

31

2SC4793

B

C

E

TOP209P

8 5

1

( TOP VIEW )

4

TYA7805CTV

TYA7809CTV

BF871-127

B

C

E

E

B C

DTA144ESA

DTA144ESA-TP

DTC114EK

DTC114EKA-T146

DTC143TKA-T146

DTC144EKA-T-146R

2SA1037K-T-146-

R2SA1162-G

2SC2412K-QR

2SC2412K-T-146-R

C

B

E

IRF614

1

( TOP VIEW )

12

1

2

3

1 V

OUT

2 V

IN

3 GND

E

C

B

B

C

E

53

2SA933AS-QRT

2SA933AS-RT

2SC1740S-RT

LETTER SIDE

E

C B

2SK2251-01-F19

ERA81-004TP1

ERA83-006

MTZJ-T-77-3.9B

MTZJ-T-77-5.6B

MTZJ-T-77-5.6C

MTZJ-T-77-6.8A

MTZJ-T-77-6.8C

MTZJ-T-77-7.5C

MTZJ-T-77-9.1A

MTZJ-T-77-9.1A

MTZJ-T-77-10

CATHODE

MTZJ-T-77-33A

MTZJ-33C

MTZJ-7.5B

RD3.9ES-B2

RD5.6ESB2

RD6.8ES-B2

RD7.5ESB2

RD9.1ES-B3

1SS119-25TD

1SS133T-77

ANODE

SEL12108-D

E

B C

AK04-V1

AU-012-V1

BYD33G

BYD33G-

AMMO

DINL20-TR

ERB44-06TP1

EG-1Z-V1

EL1Z

ERD28-06S

ERD28-08S

ERC06-15

FMN-G12S

RG1CLF-B1

RGP10GPKG23

RU3YX-LF-C4

RU3YX-V1

RU-4AM-T3

1SS292T-77

CATHODE

ANODE

DAN202K

DAN202K-T146

3

2

1

2 3

1

ANODE

UF4005PK623

CATHODE

ANODE

CATHODE

54

5-5. IC BLOCK DIAGRAMS

A BOARD IC501 STV 9379

2 6 3

A BOARD IC201 TDA7495

2

VOLUME

FLYBACK

GENERATOR

1

30K

OP AMP

1

7

-

POWER

AMPLIFIER

+

5

THERMAL

PROTECTION

VOLUME

5

30K

4

A BOARD IC101 TDA9817/V1

22 15 4 6 7 19 18

14

TUNER

AGC

VIF

AGC

1

2

VIF

AMPLIFIER

23

24

SIF

AMPLIFIER

FPLL

AFC

DETECTOR

VCO

TWO

VIDEO

DEMODULATOR

AND AMPLIFIER

QSS MIXER

INTERCARRIER

MIXER

AM DEMODULATOR

17

SIF

AGC

INTERCARRIER

MODE SWITCH

21 20

VOLTAGE

REFERENCE

FM-PLL DEMODULATOR

16

8

3

A BOARD IC606 STR-F6654

4

START

REG

T.S.D

Iconst

O.V.P

4

LATCH

O.S.C

MUTE/STBY

PROTECTIONS

OP AMP

DRIVE

60K

5 3 12 13 9 10 11

A BOARD IC301 CXA2060AS

45

APC

<HUE>

ACO DET.

CHROMA

AMP

BPF

PAL 4.43MHz

NTSC 3.58MHz

<C BPF>

ACC AMP

48 47 46

C VCO

4.433619MHz

3.579545MHz

9.582058MHz

PAL/NTSC

DEMOD

COLOR SYSTEM DISCRIMINATOR

PAL ID <PAL/NTSC> <XTAL ID>

PAL/NTSC COLOR KILLER <KILLER>

SECAM ID <SECAM>

<XTAL> <COL SYSTEM> <COL LOOP>

<ID START> <ID STOP> <HUE>

ACC AMP

BELL

FILTER

(ZAP)

LIM

AMP

ACC DET

PLL

SECAM

FM DEMOD

LINE BLK

DE-

EMPHASIS

SECAM

VCO

CAL. by

4.43MHz

5 1

SW

NTSC

PAL,SECAM

KILLER

<KILLER OFF>

1H

DELAY LINE

(PAL/SECAM)

DPIC

<DPIC>

<AGING>

CLAMP

DC TRAN

<DC TRAN>

15 39 38 37 36

EYUV CLAMP

YUV SW

<Y SEL>

YUV OUT

<C DECOD>

COLOR AMP

<COLOR>

<C DFF>

AXIS

<COL MATRIX>

Y/C MIX

RGB CLAMP

VPROT

<VNG>

VM AMP

(OFF YS/YM)

28 27 26 25 32 31 30 29

CLAMP

RGB 2/2

ABL/PEAK LIM

<ABL MODE>

<ABL VTH>

DAC

SW

FILTER ALIGNMENT

AKB

<IKR>

PC BUS

DECODER

STATUS I/T

41

4

7

9

6

43

2

CHROMA SW

Y SW

MONITOR SW

VIDEO SW

<VIDEO SEL>

<S SEL>

ATT

TRAP

PAL 4.43MHz

NTSC 3.58MHz

SECAM 4.2 - 4.43MHz

<TRAP OFF>

V SYNC SEP

<VSS>

<VSS LPF>

DL

PAL/NTSC

300 x 200nS

SECAM

300 x 200nS

<Y DELAY>

COUNT DOWN LINE COUNTER

V TIM GEN

<FIELD FREQ> <UNDER SCAN>

<CD MODE>

<INTERLACE> <FIELD ID>

H SYNC SEP

<HSS>

AFC

<APC GAIN>

<FH HIGH>

<H CENT>

H SAW GEN

H OSC

<ZAP>

20

SHARPNESS DL

SHARPNESS AMP

<SHARPNESS>

<SHP FO>

<PREOVER>

V SAW GEN

(50/50)

VTIM

WIDE SAW FUNC

<ASPECT>

<SCROLL>

<UPPER VLIN>

<LOWER VLIN>

<V ZOOM>

<V UNDER SCAN>

H TIM GEN

<H BLK>

<LEFT HBLK>

<RIGHT HBLK>

17 5

PHASE DET

<H POSITION>

<AFC BOW>

<AFC ANGLE>

HPROT

<HNG>

18

55

HD GEN

<HD W>

19

VD SAW FUNC

<VON> <S CORRECTION>

<VSIZE> <V LINEARITY>

<V POSITION> <EHT COMP>

EW PARABOLA FUNC

<H SIZE>

<PIN AMP>

<CORNER PIN>

<TRAPEZIUM>

<EW DC>

IREF REG

10 12 16 33

14

13

11

42

3

21

24

23

22

35

34

14

9

10

12

3

2

1

5

SECTION 6

EXPLODED VIEWS

NOTE :

• Items with no part number and no description are not stocked because they are seldom required for routine service.

• The construction parts of an assembled part are indicated with a collation number in the remarks column.

6-1. CHASSIS

7-685-663-79 x 1

7-685-663-71 x 8

• Items marked “ * “ are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

9

8

7

6

1

2

3

5

4

11

10

REF. NO. PART.NO DESCRIPTION REMARK

3

4

1

2

5

6

£

£

1-571-433-21 SWITCH, PUSH (AC POWER)

*4-204-141-01 BRACKET, MAIN

*4-202-531-01 AC CORD LOCK (SC)

1-765-286-11 CORD, POWER

£ 1-453-264-11 TRANSFORMER ASSY, FLYBACK (NX-1680/U2B4)

(KV-25K5K)


(KV-29K5K)

8-598-432-00 TUNER (FSS-BTP-AC411)

7

8

9

10

11


*A-1652-054-A S1 BOARD, COMPLETE

*A-1632-794-A A BOARD, COMPLETE (KV-25K5K)


*A-1646-160-A H1 BOARD, COMPLETE

X-4200-307-3 COVER ASSY, REAR (KV-25K5K)

X-4200-304-2 COVER ASSY, REAR (KV-29K5K)

4-203-713-11 COVER, REAR (KV-25K5K)

4-203-705-11 C0VER, REAR (KV-29K5K)

56

6-2. PICTURE TUBE

68

69

73

74

75

76

77

71

70

72

67

67

51 58

60

59

62

63

64

70

65

72

61

69

71

66

52

57

53

55

56

54


51

52

53

54

55

X-4200-306-5 BEZNET ASSY (KV-25K5K) 52 & 55-57

X-4200-305-7 BEZNET ASSY (KV-29K5K) 52 & 55-57

4-047-464-01 CATCHER PUSH

4-203-693-21 DOOR, ORNAMENTAL

56

57

58

59

4-204-071-01 PLATE, ORNAMENTAL

4-203-704-01 BUTTON POWER

4-202-964-01

4-204-070-01

SPRING

GUIDE, LIGHT

4-203-128-11 SHEET, BLOTTING

£ 8-733-254-05 PICTURE TUBE (SD-257)(M60LCS60X)

(KV-25K5K)

£ 8-733-856-05 PICTURE TUBE (SD-269)(M68LCT60X)

(KV-29K5K)

60 £ 8-451-404-23 DEFLECTION YOKE (Y25GXABA) (KV-25K5K)

61

£ 8-451-466-11 DEFLECTION YOKE (Y29GXC2B) (KV-29K5K)

£ 8-733-254-76 ITC (KV-25K5K)

62

£ 8-733-856-75 ITC (KV-29K5K)

£ 8-453-005-21 NECK ASSY PICTURE TUBE (NA297-M2)

(KV-29K5K)

73

74

75

76

77

69

70

71

72


63

64

65

66

67

68

£

*A-1644-093-A

*A-1638-112-A

4-369-318-31

VM BOARD, COMPLETE (KV-29K5K)

C BOARD, COMPLETE

SPRING, TENSION

1-416-465-11 COIL, DEMAGNETIZATION (KV-25K5K)

£ 1-416-654-11 COIL, DEMAGNETIZATION (KV-29K5K)

4-203-390-01 CUSHION, DGC

4-203-877-01 HOLDER, DGC BRACKET 25” (KV-25K5K)

4-203-878-01 HOLDER, DGC BRACKET 29” (KV-29K5K)

1-505-484-11 SPEAKER (2.6CM)

1-505-674-11 SPEAKER MID RANGE (8CM)

1-505-673-11 SPEAKER WOOFER (10CM)

4-039-358-01 SCREW (4X16), (+) BV TAPPING

4-308-870-00 CLIP, LEAD WIRE

1-452-094-00 MAGNET, ROTATABLE DISK; 15MM Ø

1-452-032-00 MAGNET, DISK; 10MM Ø

X-4387-214-1 PERMALLOY ASSY, CORRECTION

3-701-007-00 BAND, BINDING

57

SECTION 7

ELECTRICAL PARTS LIST

•

When indicating parts by reference number, please include the board name.

CAPACITORS

MF : mF, PF : mmF

•

COILS

MMH : mH , uH

•

•

•

Items marked “ * “ are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

All variable and adjustable resistors have characteristic curve B, unless otherwise noted.

RESISTORS

All resistors are in ohms.

F : nonflammable.

A

REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK


*****************


*****************

4-382-854-11 SCREW (M3X10), P, SW (+)

C041 1-163-205-00 CERAMIC CHIP 0.001MF 10% 50V

C042 1-126-933-11 ELECT 100MF 20% 16V

C043 1-126-935-11 ELECT 470MF 20% 16V

C103 1-104-665-11 ELECT 100MF 20% 25V

C105 1-126-965-11 ELECT 22MF 20% 50V

< CAPACITOR >

C004 1-163-038-00 CERAMIC CHIP 0.1MF 25V

C005 1-163-105-00 CERAMIC CHIP 33PF 5% 50V


C007 1-126-935-11 ELECT 470MF 20% 16V

C008 1-126-964-11 ELECT 10MF 20% 50V

C009 1-126-965-11 ELECT 22MF 20% 50V

C010 1-126-959-11 ELECT 0.47MF 20% 50V (KV-29K5K)

C011 1-126-965-11 ELECT 22MF 20% 50V

C012 1-126-959-11 ELECT 0.47MF 20% 50V





C022 1-126-935-11 ELECT 470MF 20% 16V

C024 1-104-665-11 ELECT 100MF 20% 25V

C025 1-130-495-00 FILM 0.1MF 5% 50V

C028 1-163-117-00 CERAMIC CHIP 100PF 5% 50V (KV-29K5K)


C030 1-104-665-11 ELECT 100MF 20% 25V







C038 1-126-964-11 ELECT 10MF 20% 50V



C108 1-163-465-11 CERAMIC CHIP 9PF 0.25PF 50V



C111 1-216-296-00 SHORT 0


58


C116 1-126-961-11 ELECT 2.2MF 20% 50V

C117 1-126-961-11 ELECT 2.2MF 20% 50V



C129 1-126-963-11 ELECT 4.7MF 20% 50V

C134 1-128-551-11 ELECT 22MF 20% 25V






C143 1-104-664-11 ELECT 47MF 20% 25V


C201 1-104-666-11 ELECT 220MF 20% 25V

C203 1-126-942-61 ELECT 1000MF 20% 25V

C204 1-126-942-61 ELECT 1000MF 20% 25V

C206 1-126-960-11 ELECT 1MF 20% 50V

C207 1-126-972-11 ELECT 1000MF 20% 50V

C208 1-126-960-11 ELECT 1MF 20% 50V



C302 1-126-967-11 ELECT 47MF 20% 16V

C303 1-101-004-00 CERAMIC 0.01MF 50V

C304 1-126-964-11 ELECT 10MF 20% 50V

The components identified by shading and marked are critical for safety

Replace only with the part number specified.





C309 1-126-963-11 ELECT 4.7MF 20% 50V





C317 1-136-169-00 FILM 0.22MF 5% 50V

C319 1-126-964-11 ELECT 10MF 20% 50V

C321 1-126-963-11 ELECT 4.7MF 20% 50V


C328 1-104-664-11 ELECT 47MF 20% 25V





C333 1-126-960-91 ELECT 1MF 20% 50V





C338 1-126-967-11 ELECT 47MF 20% 50V





C402 1-126-960-11 ELECT 1MF 20% 50V



C406 1-126-960-11 ELECT 1MF 20% 50V

C407 1-126-964-11 ELECT 10MF 20% 50V

C408 1-126-964-11 ELECT 10MF 20% 50V

C410 1-126-964-11 ELECT 10MF 20% 50V


C414 1-126-960-11 ELECT 1MF 20% 50V


C416 1-126-964-11 ELECT 10MF 20% 50V


C418 1-126-960-11 ELECT 1MF 20% 50V


C423 1-126-964-11 ELECT 10MF 20% 50V

C430 1-104-664-11 ELECT 47MF 20% 25V



C434 1-126-935-11 ELECT 470MF 20% 16V


A



C437 1-535-465-11 LEAD, JUMPER (5.0MM)

C438 1-535-465-11 LEAD, JUMPER (5.0MM)




C501 1-126-968-11 ELECT 100MF 20% 50V


C503 1-126-968-11 ELECT 100MF 20% 50V

C504 1-106-220-00 MYLAR 0.1MF 10% 100V

C505 1-136-173-00 FILM 0.47MF 5% 50V


C507 1-126-933-11 ELECT 100MF 20% 16V

C508 1-126-960-11 ELECT 1MF 20% 50V

C509 1-137-047-11 FILM 0.01MF 10% 400V


C511 1-102-125-00 CERAMIC 0.0047MF 10% 50V

C512 1-162-114-00 CERAMIC 0.0047MF 2KV

C513 1-107-662-11 ELECT 22MF 20% 250V

C515 1-104-666-11 ELECT 220MF 20% 25V

C517 1-104-666-11 ELECT 220MF 20% 25V

C518 1-106-375-12 MYLAR 0.022MF 99% 200V



C522 1-137-399-11 FILM 0.1MF 5% 50V

C531 1-126-964-11 ELECT 10MF 20% 50V


C533 1-163-017-00 CERAMIC CHIP 0.0047MF 10% 50V (KV-29K5K)


C536 1-115-522-11 FILM 1MF 5% 200V

C537 1-137-417-11 MYLAR 0.0047MF 10% 200V


C539 1-111-230-11 ELECT 1MF 20% 160V

C540 1-136-206-11 FILM 0.033MF 10% 400V

C541 1-106-383-00 MYLAR 0.047MF 10% 200V

C542 1-162-134-11 CERAMIC 470PF 10% 2KV

C543 1-162-134-11 CERAMIC 470PF 10% 2KV

C545 1-126-960-11 ELECT 1MF 20% 50V

C546 1-130-895-00 FILM 0.056MF 5% 400V

C547 1-117-813-11 FILM 0.75MF 5% 200V

C548 1-162-134-11 CERAMIC 470PF 10% 2KV

C550 1-107-638-11 ELECT 33MF 20% 160V

C552 1-102-212-00 CERAMIC 820PF 10% 500V

C553 1-137-417-11 MYLAR 0.0047MF 10% 200V

C555 1-117-717-11 FILM 17000P 3% 1.2KV(KV-25K5K)

1-117-648-11 FILM 15000PF 3% 1.2KV(KV-29K5K)

59

A


C571 1-123-024-21 ELECT 33MF 160V

C572 1-128-526-11 ELECT 100MF 20% 16V



C584 1-126-963-11 ELECT 4.7MF 20% 50V

C601 £ 1-107-563-11 FILM 0.1MF 20% 300V

C602 £ 1-107-563-11 FILM 0.1MF 20% 300V

C603 £ 1-117-700-51 CERAMIC 0.0022MF 99% 250V

C604 £ 1-117-700-51 CERAMIC 0.0022MF 99% 250V

C605 1-104-652-11 ELECT 470MF 20% 10V

C606 1-125-555-11 ELECT(BLOCK) 330MF 20% 400V

C607 1-125-787-51 CERAMIC 680PF 10% 2KV

C609 1-107-915-11 ELECT 2200MF 20% 50V

C610 1-104-665-11 ELECT 100MF 20% 25V

C611 1-165-127-11 CERAMIC 470PF 10% 500V

C612 £ 1-161-964-51 CERAMIC 0.0047MF 250V

C613 £ 1-161-964-51 CERAMIC 0.0047MF 250V

C614 £ 1-161-964-51 CERAMIC 0.0047MF 250V

C615 1-130-202-00 FILM 0.022MF 10% 400V

C618 1-107-890-11 ELECT 2200MF 20% 25V


C622 £ 1-161-964-51 CERAMIC 0.0047MF 250V

C624 1-104-665-11 ELECT 100MF 20% 25V

C625 1-104-665-11 ELECT 100MF 20% 25V

C628 1-124-347-00 ELECT 100MF 20% 160V

C629 1-136-189-00 FILM 0.1MF 10% 250V

C630 1-165-127-11 CERAMIC 470PF 10% 500V

C633 1-104-332-11 CERAMIC 470PF 10% 2KV

C635 1-107-675-11 ELECT 1MF 20% 160V

C638 1-107-670-11 ELECT 10MF 20% 400V

C639 1-104-665-11 ELECT 100MF 20% 25V

C640 1-104-664-11 ELECT 47MF 20% 25V

C641 1-104-665-11 ELECT 100MF 20% 25V

C642 1-104-665-11 ELECT 100MF 20% 25V

C646 1-107-974-11 CERAMIC 47PF 5% 2KV

< FILTER >

CF101 1-404-134-00 TRAP, CERAMIC (5.5MHZ)

SWF101 1-767-874-11 FILTER, SURFACE WAVE

SWF102 1-767-873-11 FILTER, SURFACE WAVE

< CONNECTOR >

CN001 *1-564-508-11 PLUG, CONNECTOR 5P


CN101 1-766-922-11 CONNECTOR, BOARD TO BOARD 18P






CN406 1-564-511-11 PLUG, CONNECTOR 8P

CN501 *1-580-798-11 CONNECTOR PIN (DY) 6P

CN502 *1-691-135-11 PIN, CONNECTOR (PC BOARD) 4P

CN503 *1-564-507-11 PLUG, CONNECTOR 4P (KV-29K5K)


CN505 *1-568-882-51 PIN, CONNECTOR 7P (KV-29K5K)

CN506 1-695-915-11 TAB (CONTACT)

CN509 *1-508-784-00 PIN, CONNECTOR (5MM PITCH) 1P (KV-29K5K)

CN602 £ 1-508-765-00 PIN, CONNECTOR (5MM PITCH) 3P

CN603 £ 1-508-786-00 PIN, CONNECTOR (5MM PITCH) 2P

CN606 £ *1-691-291-11 PIN, CONNECTOR (PC BOARD) 5P

< DIODE >

D001 8-719-109-89 DIODE RD5.6ESB2

D002 8-719-109-89 DIODE RD5.6ESB2

D004 8-719-109-89 DIODE RD5.6ESB2

D005 8-719-109-89 DIODE RD5.6ESB2

D007 8-719-109-89 DIODE RD5.6ESB2

D008 8-719-991-33 DIODE 1SS133T-77

D009 8-719-109-89 DIODE RD5.6ESB2

D010 8-719-109-89 DIODE RD5.6ESB2

D011 8-719-109-89 DIODE RD5.6ESB2

D012 8-719-914-43 DIODE DAN202K

D014 8-719-058-24 DIODE RB501V-40TE-17

D015 8-719-914-43 DIODE DAN202K

D017 8-719-109-89 DIODE RD5.6ESB2

D018 8-719-991-33 DIODE 1SS133T-77

D023 8-719-109-89 DIODE RD5.6ESB2

D101 8-719-982-24 DIODE MTZJ-33A

D201 8-719-929-15 DIODE HZS9.INBZ

D202 8-719-914-43 DIODE DAN202K

D204 8-719-109-89 DIODE RD5.6ESB2

D205 8-719-109-89 DIODE RD5.6ESB2

D206 8-719-109-89 DIODE RD5.6ESB2

D306 8-719-109-89 DIODE RD5.6ESB2

D307 8-719-109-89 DIODE RD5.6ESB2

D308 8-719-109-72 DIODE RD3.9ESB2

D309 8-719-991-33 DIODE 1SS133T-77

D320 8-719-929-15 DIODE HZS9.INB2

D402 8-719-109-89 DIODE RD5.6ESB2

D405 8-719-109-97 DIODE RD6.8ES-B2

D406 8-719-109-97 DIODE RD6.8ES-B2

D407 8-719-109-97 DIODE RD6.8ES-B2

D408 8-719-929-15 DIODE HZS9.INB2

D409 8-719-109-97 DIODE RD6.8ES-B2

D410 8-719-109-89 DIODE RD5.6ESB2

D414 8-719-109-97 DIODE RD6.8ES-B2

60




D415 8-719-929-15 DIODE HZS9.INBZ

D417 8-719-929-15 DIODE HZS9-INB2

D418 8-719-929-15 DIODE HZS9-INB2

D419 8-719-929-15 DIODE HZS9-INB2

D422 8-719-109-97 DIODE RD6.8ES-B2

D423 8-719-109-97 DIODE RD6.8ES-B2

D427 8-719-109-97 DIODE RD6.8ES-B2

D501 8-719-302-43 DIODE EL1Z

D502 8-719-924-13 DIODE MTZJ-T-77-22B

D511 8-719-028-72 DIODE RGP02-17EL-6433

D512 8-719-302-43 DIODE EL1Z

D513 8-719-979-85 DIODE EGP20G

D514 8-719-979-85 DIODE EGP20G

D534 8-719-302-43 DIODE EL1Z

D535 8-719-908-03 DIODE GP08D

D536 8-719-945-80 DIODE ERC06-15S

D538 8-719-908-03 DIODE GP08D

D539 8-719-900-26 DIODE ERD29-08J

D541 1-535-465-11 LEAD, JUMPER (5.0MM)

D571 8-719-911-19 DIODE 1SS119-25

D573 8-719-921-40 DIODE MTZJ-4.7C

D601 8-719-510-53 DIODE D4SB60L

D602 8-719-046-74 DIODE AU-01Z-V1

D603 8-719-312-61 DIODE EU-1Z

D605 8-719-312-10 DIODE RU4AM-T3

D608 8-719-067-88 DIODE RG1CLF-B1

D610 8-719-067-78 DIODE RN3Z-LF014-302

D613 8-719-911-19 DIODE 1SS119-25

D614 8-719-058-38 DIODE FMN-G12S

D619 8-719-043-76 DIODE AK04V0

D621 8-719-068-00 DIODE ERC04-06SE

D626 8-719-068-00 DIODE ERC04-06SE

D627 8-719-510-26 DIODE D1NL20

D628 8-719-059-23 DIODE P6KE200AG23

D629 8-719-979-64 DIODE UF4005PKG23

D631 8-719-110-31 DIODE RD12ES-B2

D632 8-719-510-64 DIODE S2LA20F

D633 8-719-109-89 DIODE RD5.6ESB2

< FERRITE BEAD >

FB001 1-412-911-11 FERRITE 0UH

FB002 1-412-911-11 FERRITE 0UH

FB601 1-412-911-11 FERRITE 0UH

FB602 1-412-911-11 FERRITE 0UH

FB605 1-410-397-21 FERRITE 1.1UH

FB608 1-412-911-11 FERRITE 0UH

FB609 1-535-465-11 LEAD, JUMPER (5.0MM)

A


FB610 1-410-397-21 FERRITE 1.1UH

FB611 1-410-397-21 FERRITE 1.1UH

FB612 1-535-465-11 LEAD, JUMPER (5.0MM)

< IC >

IC001 8-759-526-01 SAA5497PS/MIA/038

IC003 8-759-468-56 IC MN1381T

IC004 8-759-432-33 IC ST24W08FM6TR

IC005 8-759-516-41 IC CD4052BCM

IC101 8-759-466-49 IC TDA9817/V1

IC201 8-759-442-74 IC TDA7495

IC301 8-752-082-35 IC CXA2060AS

IC501 8-759-192-71 IC STV9379

IC531 8-759-450-95 IC LM393N

IC603 8-749-920-61 IC SE135N

IC604 8-759-524-82 IC TYA7805CTV

IC605 8-759-524-83 IC TYA7809CTV

IC606 8-749-013-75 IC STR-F6654

IC608 8-759-524-82 IC TYA7805CTV

IC609 8-759-468-89 IC TOP209P

< SOCKET >

J401 1-766-296-11 CONNECTOR, DUAL SCART

J404 1-770-989-11 JACK, PIN 2P

< COIL >

L001 1-408-603-31 INDUCTOR 10UH

L102 1-408-599-21 INDUCTOR 4.7UH

L103 1-403-686-11 COIL

L104 1-410-671-31 INDUCTOR 47UH

L106 1-408-417-00 INDUCTOR 47UH

L201 1-535 465 11 LEAD, JUMPER (5.0MM)

L202 1-535-465-11 LEAD, JUMPER (5.0MM)

L203 1-406-979-11 INDUCTOR 0UH

L302 1-408-417-00 INDUCTOR 47UH

L303 1-408-609-41 INDUCTOR 33UH

L401 1-408-417-00 INDUCTOR 47UH

L402 1-408-417-00 INDUCTOR 47UH

L405 1-216-295-00 SHORT 0

L406 1-216-295-00 SHORT 0

L501 1-408-417-00 INDUCTOR 47UH

L502 1-412-529-11 INDUCTOR 22UH

L503 1-412-521-31 INDUCTOR 4.7UH

L532 1-412-553-11 INDUCTOR 3.3MMH

L533 1-406-989-21 INDUCTOR 0UH

L535 1-459-111-00 INDUCTOR 0UH

61

A


L537 1-409-756-11 COIL, HORIZONTAL LINEARITY (KV-25K5K)

1-409-855-11 COIL, HORIZONTAL LINEARITY (KV-29K5K)

L540 1-535 465 11 LEAD, JUMPER (5.0MM)

L571 1-412-533-21 INDUCTOR 47UH

L602 1-408-417-00 INDUCTOR 47UH

< PHOTO COUPLER >

PH601 £ 8-749-010-64 PHOTO COUPLER PC123F2

< TRANSISTOR >

Q004 8-729-216-22 TRANSISTOR 2SA1162-G

Q005 1-801-806-11 TRANSISTOR DTC144EKA


Q007 8-729-620-06 TRANSISTOR 2SC3052-EF






Q013 8-729-620-06 TRANSISTOR 2SC3052-EF (KV-29K5K)




R001 1-216-025-00 RES,CHIP 100 5% 1/10W

R002 1-216-025-00 RES,CHIP 100 5% 1/10W

R003 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R004 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R005 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R007 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R009 1-216-025-00 RES,CHIP 100 5% 1/10W

R010 1-216-025-00 RES,CHIP 100 5% 1/10W

R011 1-216-025-00 RES,CHIP 100 5% 1/10W

R012 1-247-807-31 CARBON 100 5% 1/4W

R013 1-216-214-00 RES,CHIP 4.7K 5% 1/8W

R014 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R015 1-216-049-00 RES,CHIP 1K 5% 1/10W

R019 1-216-053-00 RES,CHIP 1.5K 5% 1/10W

R023 1-216-295-00 SHORT 0

R029 1-216-073-00 RES,CHIP 10K 5% 1/10W

R030 1-216-081-00 RES,CHIP 22K 5% 1/10W (KV-29K5K)

R032 1-216-089-00 RES,CHIP 47K 5% 1/10W

R034 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R035 1-216-049-00 RES,CHIP 1K 5% 1/10W

Q014 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Q101 8-729-216-22 TRANSISTOR 2SA1162-G


Q401 1-729-920-72 TRANSISTOR 2SA1037K




Q532 8-729-038-83 TRANSISTOR 2SK2251-01-F19

Q533 8-729-040-62 TRANSISTOR 2SD2539(LBSONY)

Q535 8-729-119-80 TRANSISTOR 2SC2688-LK

Q571 8-729-105-08 TRANSISTOR 2SA1330-O6




Q601 8-729-216-22 TRANSISTOR 2SA1162-G

< RESISTOR >

R036 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R038 1-216-073-00 RES,CHIP 10K 5% 1/10W

R039 1-216-089-91 RES,CHIP 47K 5% 1/10W

R050 1-216-041-00 RES,CHIP 470 5% 1/10W

R051 1-216-049-00 RES,CHIP 1K 5% 1/10W

R053 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R054 1-216-041-00 RES,CHIP 470 5% 1/10W

R055 1-216-081-00 RES,CHIP 22K 5% 1/10W

R056 1-216-105-00 RES,CHIP 220K 5% 1/10W

R057 1-216-075-00 RES,CHIP 12K 5% 1/10W

R058 1-216-063-91 RES,CHIP 3.9K 5% 1/10W

R059 1-216-089-00 RES,CHIP 47K 5% 1/10W

R060 1-216-174-00 RES,CHIP 100 5% 1/8W

R061 1-216-174-00 RES,CHIP 100 5% 1/8W

R062 1-216-033-00 RES,CHIP 220 5% 1/10W

JR023 1-216-296-00 SHORT 0

JR031 1-216-295-00 SHORT 0

JR033 1-216-296-00 SHORT 0

JR403 1-216-073-00 RES,CHIP 10K 5% 1/10W

JR409 1-216-295-00 SHORT 0

R065 1-216-025-00 RES,CHIP 100 5% 1/10W

R066 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R067 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R069 1-216-049-00 RES,CHIP 1K 5% 1/10W

R070 1-216-081-00 RES,CHIP 22K 5% 1/10W

JR411 1-216-295-00 SHORT 0

JR412 1-216-295-00 SHORT 0

JR610 1-216-296-00 SHORT 0

JR613 1-216-296-00 SHORT 0

JW220 8-719-109-89 DIODE RDS.6ESB2

R071 1-216-214-00 RES,CHIP 4.7K 5% 1/8W

R072 1-216-097-00 RES,CHIP 100K 5% 1/10W

R073 1-216-097-00 RES,CHIP 100K 5% 1/10W

R075 1-216-069-00 RES,CHIP 6.8K 5% 1/10W

R077 1-216-083-00 RES,CHIP 27K 5% 1/10W

R078 1-216-065-00 RES,CHIP 4.7K 5% 1/10W (KV-29K5K)

R080 1-216-073-00 RES,CHIP 10K 5% 1/10W

62




R081 1-216-073-00 RES,CHIP 10K 5% 1/10W

R082 1-216-053-00 RES,CHIP 1.5K 5% 1/10W

R083 1-216-031-00 RES,CHIP 180 5% 1/10W

R084 1-216-053-00 RES,CHIP 1.5K 5% 1/10W

R085 1-216-031-00 RES,CHIP 180 5% 1/10W

R086 1-216-053-00 RES,CHIP 1.5K 5% 1/10W

R087 1-216-180-00 RES,CHIP 180 5% 1/8W

R088 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R089 1-216-081-00 RES,CHIP 22K 5% 1/10W (KV-29K5K)

R090 1-216-057-00 RES,CHIP 2.2K 5% 1/10W (KV-29K5K)

R091 1-216-081-00 RES,CHIP 22K 5% 1/10W (KV-29K5K)

R092 1-216-073-00 RES,CHIP 10K 5% 1/10W (KV-29K5K)

R093 1-216-230-00 RES,CHIP 22K 5% 1/8W

R094 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R095 1-216-025-00 RES,CHIP 100 5% 1/10W

R096 1-247-807-31 CARBON 100 5% 1/4W

R097 1-247-807-31 CARBON 100 5% 1/4W

R098 1-247-807-31 CARBON 100 5% 1/4W

R099 1-247-807-31 CARBON 100 5% 1/4W

R101 1-216-049-00 RES,CHIP 1K 5% 1/10W

R106 1-215-900-11 METAL OXIDE 22K 5% 2W F

R116 1-249-437-11 CARBON 47K 5% 1/4W

R120 1-216-037-00 RES,CHIP 330 5% 1/10W

R121 1-216-025-00 RES,CHIP 100 5% 1/10W

R122 1-216-025-00 RES,CHIP 100 5% 1/10W

R133 1-216-295-00 SHORT 0

R142 1-216-295-00 SHORT 0

R143 1-216-025-00 RES,CHIP 100 5% 1/10W

R144 1-216-079-00 RES,CHIP 18K 5% 1/10W

R145 1-216-212-00 RES,CHIP 3.9K 5% 1/8W

R151 1-216-049-00 RES,CHIP 1K 5% 1/10W

R154 1-216-238-91 RES,CHIP 47K 5% 1/8W

R155 1-216-089-00 RES,CHIP 47K 5% 1/10W

R204 1-247-863-91 CARBON 22K 5% 1/4W

R206 1-216-085-00 RES,CHIP 33K 5% 1/10W

R207 1-216-295-00 SHORT 0

R209 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R211 1-215-873-00 METAL OXIDE 4.7K 5% 1W F

R213 1-216-089-00 RES,CHIP 47K 5% 1/10W

R301 1-216-025-00 RES,CHIP 100 5% 1/10W

R302 1-216-081-00 RES,CHIP 22K 5% 1/10W

R303 1-216-073-00 RES,CHIP 10K 5% 1/10W

R304 1-216-073-00 RES,CHIP 10K 5% 1/10W

R306 1-216-206-00 RES,CHIP 2.2K 5% 1/8W

R309 1-216-675-11 METAL CHIP 10K 0.50% 1/10W

R310 1-216-022-00 RES,CHIP 75 5% 1/10W

R311 1-216-022-00 RES,CHIP 75 5% 1/10W

A


R313 1-216-025-00 RES,CHIP 100 5% 1/10W

R314 1-216-025-00 RES,CHIP 100 5% 1/10W

R315 1-216-075-91 RES,CHIP 12K 5% 1/10W

R316 1-216-025-00 RES,CHIP 100 5% 1/10W

R317 1-216-049-00 RES,CHIP 1K 5% 1/10W

R318 1-216-025-00 RES,CHIP 100 5% 1/10W

R319 1-216-025-00 RES,CHIP 100 5% 1/10W

R320 1-216-025-00 RES,CHIP 100 5% 1/10W

R321 1-216-025-00 RES,CHIP 100 5% 1/10W

R323 1-216-025-00 RES,CHIP 100 5% 1/10W

R324 1-412-002-21 INDUCTOR 4.7UH

R325 1-412-002-21 INDUCTOR 4.7UH

R326 1-216-129-00 RES,CHIP 2.2M 5% 1/10W

R327 1-216-295-00 SHORT 0

R331 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R332 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R333 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R334 1-216-025-00 RES,CHIP 100 5% 1/10W

R335 1-216-025-00 RES,CHIP 100 5% 1/10W

R337 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R338 1-216-049-00 RES,CHIP 1K 5% 1/10W

R401 1-216-113-00 RES,CHIP 470K 5% 1/10W

R402 1-216-295-71 CONDUCTER CHIP

R403 1-216-041-00 RES,CHIP 470 5% 1/10W

R404 1-216-113-00 RES,CHIP 470K 5% 1/10W

R405 1-216-295-00 SHORT 0

R406 1-216-113-00 RES,CHIP 470K 5% 1/10W

R408 1-216-022-00 RES,CHIP 75 5% 1/10W

R409 1-216-029-00 RES,CHIP 150 5% 1/10W

R410 1-216-029-00 RES,CHIP 150 5% 1/10W

R411 1-216-022-00 RES,CHIP 75 5% 1/10W

R412 1-216-029-00 RES,CHIP 150 5% 1/10W

R413 1-216-295-00 SHORT 0

R414 1-216-022-00 RES,CHIP 75 5% 1/10W

R415 1-216-022-00 RES,CHIP 75 5% 1/10W

R417 1-260-158-11 CARBON 75 5% 1/2W

R418 1-247-823-31 CARBON 470 5% 1/4W

R419 1-216-022-00 RES,CHIP 75 5% 1/10W

R420 1-216-041-00 RES,CHIP 470 5% 1/10W

R421 1-216-113-00 RES,CHIP 470K 5% 1/10W

R422 1-216-295-00 SHORT 0

R425 1-216-077-00 RES,CHIP 15K 5% 1/10W

R426 1-216-073-00 RES,CHIP 10K 5% 1/10W

R427 1-216-113-00 RES,CHIP 470K 5% 1/10W

R429 1-216-041-00 RES,CHIP 470 5% 1/10W

R430 1-216-113-00 RES,CHIP 470K 5% 1/10W

R431 1-216-295-00 SHORT 0

63

A


R432 1-216-113-00 RES,CHIP 470K 5% 1/10W

R435 1-216-022-00 RES,CHIP 75 5% 1/10W

R436 1-216-041-00 RES,CHIP 470 5% 1/10W

R439 1-216-041-00 RES,CHIP 470 5% 1/10W

R440 1-216-113-00 RES,CHIP 470K 5% 1/10W

R441 1-216-295-00 SHORT 0

R442 1-216-077-00 RES,CHIP 15K 5% 1/10W

R443 1-216-073-00 RES,CHIP 10K 5% 1/10W

R450 1-216-041-00 RES,CHIP 470 5% 1/10W

R454 1-216-041-00 RES,CHIP 470 5% 1/10W

R457 1-216-025-00 RES,CHIP 100 5% 1/10W

R459 1-247-807-31 CARBON 100 5% 1/4W

R460 1-249-403-11 CARBON 68 5% 1/4W

R501 1-216-081-00 RES,CHIP 22K 5% 1/10W

R502 1-216-097-00 RES,CHIP 100K 5% 1/10W

R503 1-215-888-00 METAL OXIDE 220 5% 2W F

R504 1-249-385-11 CARBON 2.2 5% 1/4W F

R505 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R506 1-216-061-00 RES,CHIP 3.3K 5% 1/10W

R507 1-216-349-00 METAL OXIDE 1 5% 1W F

R508 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R509 1-216-061-00 RES,CHIP 3.3K 5% 1/10W

R510 1-216-081-00 RES,CHIP 22K 5% 1/10W

R511 1-215-869-11 METAL OXIDE 1K 5% 1W F

R512 1-249-377-11 CARBON 0.47 5% 1/4W F

R513 1-216-097-00 RES,CHIP 100K 5% 1/10W

R514 1-249-377-11 CARBON 0.47 5% 1/4W F

R515 1-249-377-11 CARBON 0.47 5% 1/4W F

R516 1-249-493-11 CARBON 56K 5% 1/2W

R517 1-249-434-11 CARBON 27K 5% 1/4W (KV-25K5K)

1-249-429-11 CARBON 10K 5% 1/4W (KV-29K5K)

R518 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R520 1-215-884-11 METAL OXIDE 47 5% 2W F

R521 1-216-117-00 RES,CHIP 680K 5% 1/10W (KV-25K5K)

1-208-845-11 RES,CHIP 1M 5% 1/10W (KV-29K5K)

R522 1-216-097-00 RES,CHIP 100K 5% 1/10W

R523 1-208-845-11 RES,CHIP 1M 5% 1/10W

R524 1-216-083-00 RES,CHIP 27K 5% 1/10W

R525 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R526 1-216-089-00 RES,CHIP 47K 5% 1/10W

R527 1-216-077-00 RES,CHIP 15K 5% 1/10W

R528 1-216-246-00 RES,CHIP 100K 5% 1/8W

R529 1-216-073-00 RES,CHIP 10K 5% 1/10W

R530 1-216-085-00 RES,CHIP 33K 5% 1/10W

R531 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R532 1-216-063-91 RES,CHIP 3.9K 5% 1/10W

R533 1-216-073-00 RES,CHIP 10K 5% 1/10W




R534 1-216-107-00 RES,CHIP 220K 5% 1/10W (KV-25K5K)

1-216-113-91 RES,CHIP 470K 5% 1/10W (KV-29K5K)

R535 1-216-109-00 RES,CHIP 330K 5% 1/10W (KV-25K5K)

1-216-101-00 RES,CHIP 150K 5% 1/10W (KV-29K5K)

R539 1-216-049-00 RES,CHIP 1K 5% 1/10W

R540 1-215-861-00 METAL OXIDE 47 5% 1W F

R541 1-216-095-00 RES,CHIP 82K 5% 1/10W (KV-25K5K)

1-216-097-00 RES,CHIP 100K 5% 1/10W (KV-29K5K)

R542 1-216-089-00 RES,CHIP 47K 5% 1/10W

R543 1-216-089-00 RES,CHIP 47K 5% 1/10W

R546 1-249-401-11 METAL OXIDE 47 5% 2W F (KV-25K5K)

1-215-893-11 METAL OXIDE 1.5K 5% 2W F (KV-29K5K)

R547 1-535-143-71 LEAD JUMPER (7.5MM) (KV-25K5K)

1-215-893-11 METAL OXIDE 1.5K 5% 2W F (KV-29K5K)

R548 1-216-397-11 METAL OXIDE 4.7 5% 3W F

R549 1-216-341-11 METAL OXIDE 0.22 5% 1W F

R551 1-215-873-21 METAL OXIDE 4.7K 5% 1W F

R552 1-216-061-00 RES,CHIP 3.3K 5% 1/10W

R553 1-249-381-11 CARBON 1 5% 1/4W F

R571 1-249-417-11 CARBON 1K 5% 1/4W F

R572 1-216-369-00 METAL OXIDE 1 5% 2W F

R573 1-216-101-00 RES,CHIP 150K 5% 1/10W (KV-25K5K)

1-216-097-00 RES,CHIP 100K 5% 1/10W (KV-29K5K)

R574 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R575 1-216-097-00 RES,CHIP 100K 5% 1/10W

R576 1-408-599-31 INDUCTOR 4.7UH

R581 1-216-089-00 RES,CHIP 47K 5% 1/10W

R582 1-216-089-00 RES,CHIP 47K 5% 1/10W

R583 1-216-081-00 RES,CHIP 22K 5% 1/10W

R588 1-216-053-00 RES,CHIP 1.5K 5% 1/10W

R589 1-216-097-00 RES,CHIP 100K 5% 1/10W

R590 1-216-081-00 RES,CHIP 22K 5% 1/10W

R591 1-217-778-77 FUSIBLE 1K 5% 1W F

R593 1-249-439-11 CARBON 68K 5% 1/4W

R594 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R602 1-202-961-11 CEMENTED 1.8 5% 10W

R603 1-202-933-61 FUSIBLE 0.1 10% 1/2W F

R607 £ 1-202-961-11 CEMENTED 1.8 5% 10W

R608 1-215-927-00 METAL OXIDE 47K 5% 3W F

R611 1-249-415-11 CARBON 680 5% 1/4W

R613 £ 1-240-030-91 METAL 4.7M 5% 1/2W

R614 £ 1-240-030-91 METAL 4.7M 5% 1/2W

R615 1-249-422-11 CARBON 2.7K 5% 1/4W

R616 1-216-393-00 METAL OXIDE 2.2 5% 3W F

R617 1-249-405-11 CARBON 100 5% 1/4W F

R619 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

64




R622 1-249-401-11 CARBON 47 5% 1/4W

R627 1-249-389-11 CARBON 4.7 5% 1/4W F

R628 1-247-791-91 CARBON 22 5% 1/4W

R652 1-216-393-00 METAL OXIDE 2.2 5% 3W F

R653 1-216-393-00 METAL OXIDE 2.2 5% 3W F

R658 1-215-929-11 METAL OXIDE 100K 5% 3W F

R659 1-216-383-21 METAL OXIDE 0.33 5% 3W F

R660 1-216-384-21 METAL OXIDE 0.39 5% 3W F

R661 1-247-843-11 CARBON 3.3K 5% 1/4W

R662 1-215-929-11 METAL OXIDE 100K 5% 3W F

R664 1-249-417-11 CARBON 1K 5% 1/4W

R665 1-215-877-11 METAL OXIDE 22K 5% 1W F

R667 1-215-927-00 METAL OXIDE 47K 5% 3W F

R900 1-249-429-11 CARBON 10K 5% 1/4W

< RELAY >

RY601 £ 1-755-245-11 RELAY

< SWITCH >

SW532 1-572-707-11 SWITCH, LEVER

< TRANSFORMER >

T511 £ 1-453-264-11 TRANSFORMER ASSY, FLYBACK (NX-1680/U2B4)

(KV-25K5K)

1-453-265-11 TRANSFORMER ASSY, FLYBACK (NX-1681/U2B4)

(KV-29K5K)

T531 1-437-195-11 TRANSFORMER, HORIZONTAL DRIVE

T532 1-431-228-11 TRANSFORMER, POWER MODULATION

T601 £ 1-427-962-11 TRANSFORMER, LINE FILTER

T602 1-431-732-11 TRANSFORMER, CONVERTER (SRT)

T603 £ 1-431-777-11 TRANSFORMER, CONVERTER

< THERMISTOR >

THP601 £ 1-810-961-11 THERMISTOR, POSITIVE

< TUNER >

TU101 8-598-432-00 TUNER (FSS BTP-AC411)

< CRYSTAL >

X001 1-578-774-11 VIBRATOR, CRYSTAL

X302 1-567-505-11 OSCILLATOR, CRYSTAL

X303 1-567-504-11 OSCILLATOR, CRYSTAL

A


C

*A-1638-112-A C BOARD, COMPLETE

*****************

< CAPACITOR >

C701 1-102-114-00 CERAMIC 470PF 10% 50V

C702 1-102-115-00 CERAMIC 560PF 10% 50V

C703 1-102-116-00 CERAMIC 680PF 10% 50V

C708 1-162-114-00 CERAMIC 0.0047MF 2KV

C710 1-107-652-11 ELECT 10MF 20% 250V

C712 1-102-116-00 CERAMIC 680PF 10% 50V

C714 1-126-967-11 ELECT 47MF 20% 16V

C717 1-102-114-00 CERAMIC 470PF 10% 50V

C718 1-102-114-00 CERAMIC 470PF 10% 50V

C719 1-102-114-00 CERAMIC 470PF 10% 50V

C722 1-101-880-00 CERAMIC 47PF 5% 50V

C723 1-101-880-00 CERAMIC 47PF 5% 50V

C724 1-101-880-00 CERAMIC 47PF 5% 50V

< CONNECTOR >

CN701 1-784-633-11 PIN, CONNECTOR 4P

CN702 1-695-915-11 TAB (CONTACT)


< DIODE >

D702 8-719-991-33 DIODE 1SS133T-77

D703 1-535-465-11 DIODE 1SS133T-77

D704 1-535-465-11 DIODE 1SS133T-77

D705 1-535-465-11 DIODE 1SS133T-77

D706 8-719-991-33 DIODE 1SS133T-77

D707 8-719-991-33 DIODE 1SS133T-77

D708 8-719-991-33 DIODE 1SS133T-77

D709 8-719-991-33 DIODE 1SS133T-77

D710 8-719-991-33 DIODE 1SS133T-77

D711 1-216-549-51 LEAD, RES, FILM 1 5% 1W

D714 8-719-991-33 DIODE 1SS133T-77

D715 8-719-991-33 DIODE 1SS133T-77

D716 8-719-991-33 DIODE 1SS133T-77

D717 8-719-991-33 DIODE 1SS133T-77

D718 8-719-991-33 DIODE 1SS133T-77

D719 8-719-991-33 DIODE 1SS133T-77

< CRT SOCKET >

J701 £ 1-526-990-21 SOCKET, CRT

< COIL >

L704 1-408-609-41 INDUCTOR 33UH

65

C VM


< TRANSISTOR >

Q702 8-729-119-78 TRANSISTOR 2SC2785-HFE

Q703 8-729-906-70 TRANSISTOR BF871-127

Q704 8-729-200-17 TRANSISTOR BF421L-AMMO


Q706 8-729-906-70 TRANSISTOR BF871-127



Q709 8-729-906-70 TRANSISTOR BF871-127


< RESISTOR >

R701 1-247-895-91 CARBON 470K 5% 1/4W

R704 1-216-486-00 METAL OXIDE 8.2K 5% 3W F

R705 1-260-103-11 CARBON 2.2K 5% 1/2W

R706 1-247-815-91 CARBON 220 5% 1/4W

R707 1-247-815-91 CARBON 220 5% 1/4W

R708 1-247-791-91 CARBON 22 5% 1/4W

R709 1-202-844-00 SOLID 330K 10% 1/2W

R711 1-247-843-11 CARBON 3.3K 5% 1/4W

R712 1-260-103-11 CARBON 2.2K 5% 1/2W

R713 1-247-875-91 CARBON 68K 5% 1/4W

R714 1-216-486-00 METAL OXIDE 8.2K 5% 3W F

R715 1-249-417-11 CARBON 1K 5% 1/4W

R716 1-247-815-91 CARBON 220 5% 1/4W

R717 1-247-815-91 CARBON 220 5% 1/4W

R718 1-202-814-11 SOLID 33K 10% 1/2W

R719 1-247-791-91 CARBON 22 5% 1/4W

R720 1-247-843-11 CARBON 3.3K 5% 1/4W

R722 1-202-848-00 SOLID 680K 10% 1/2W

R723 1-249-417-11 CARBON 1K 5% 1/4W

R724 1-260-131-11 CARBON 470K 5% 1/2W

R726 1-260-103-11 CARBON 2.2K 5% 1/2W

R727 1-247-815-91 CARBON 220 5% 1/4W

R728 1-216-351-00 METAL OXIDE 1.5 5% 1W F

R729 1-247-815-91 CARBON 220 5% 1/4W

R730 1-247-791-91 CARBON 22 5% 1/4W

R731 1-247-843-11 CARBON 3.3K 5% 1/4W

R733 1-247-823-91 CARBON 470 5% 1/4W

R734 1-247-807-31 CARBON 100 5% 1/4W

R735 1-247-823-91 CARBON 470 5% 1/4W

R736 1-216-486-00 METAL OXIDE 8.2K 5% 3W F

R737 1-247-891-91 CARBON 330K 5% 1/4W

R739 1-249-417-11 CARBON 1K 5% 1/4W

R740 1-247-823-91 CARBON 470 5% 1/4W

R741 1-202-549-00 SOLID 100 20% 1/2W

R744 1-249-421-11 CARBON 2.2K 5% 1/4W




R745 1-249-421-11 CARBON 2.2K 5% 1/4W

R746 1-249-421-11 CARBON 2.2K 5% 1/4W

< VARIABLE RESISTOR >

RV701 1-230-641-11 RES, ADJ, METAL GLAZE 2.2M

RV702 1-241-656-21 RES, ADJ, METAL FILM 110M

*********************************************************************

*A-1644-093-A VM BOARD, COMPLETE (KV-29K5 ONLY)

******************

< CAPACITOR >

C1701 1-126-933-11 ELECT 100MF 20% 16V

C1702 1-128-551-11 ELECT 22MF 20% 25V

C1703 1-126-933-11 ELECT 100MF 20% 16V

C1704 1-107-357-11 FILM 0.47MF 5% 100V

C1705 1-107-638-11 ELECT 33MF 20% 160V

C1706 1-104-999-11 FILM 0.1MF 5% 200V

C1707 1-136-207-11 FILM 0.047MF 10% 250V

C1708 1-137-364-11 FILM 0.001MF 5% 50V

C1709 1-137-364-11 FILM 0.001MF 5% 50V


C1720 1-107-667-11 ELECT 2.2MF 20% 160V

C1721 1-136-207-11 FILM 0.047MF 10% 250V

C1722 1-126-934-11 ELECT 220MF 20% 16V

C1723 1-161-830-00 CERAMIC 0.0047MF 500V

C1725 1-535-465-11 LEAD, JUMPER (5.0MM)

C1726 1-126-934-11 ELECT 220MF 20% 16V


C1804 1-126-964-11 ELECT 10MF 20% 50V

C1805 1-137-366-11 FILM 0.0022MF 5% 50V


C1844 1-130-959-00 FILM 0.047MF 10% 400V

C1845 1-136-175-00 FILM 0.68MF 5% 50V


C1902 1-137-374-11 FILM 0.047MF 5% 50V

C1903 1-126-964-11 ELECT 10MF 20% 50V

C1904 1-137-366-11 FILM 0.0022MF 5% 50V

C1905 1-137-374-11 FILM 0.047MF 5% 50V


C1911 1-136-189-00 FILM 0.1MF 10% 250V

C1912 1-129-702-00 FILM 0.001MF 5% 630V

C1913 1-136-558-11 FILM 0.0039MF 5% 630V

C1914 1-102-157-00 CERAMIC 560PF 10% 500V

C1915 1-137-102-11 FILM 0.022MF 10% 250V

C1951 1-126-964-11 ELECT 10MF 20% 50V

66





C1953 1-136-165-00 FILM 0.1MF 5% 50V


C1955 1-136-165-00 FILM 0.1MF 5% 50V

C1956 1-126-964-11 ELECT 10MF 20% 50V

C1957 1-126-964-11 ELECT 10MF 20% 50V

C1958 1-136-173-00 FILM 0.47MF 5% 50V

C1959 1-107-714-11 ELECT 10MF 20% 50V

C1960 1-107-636-11 ELECT 10MF 20% 160V

< CONNECTOR >




CN1803 1-564-507-71 PIN, CONNECTOR 4P

CN1809 1-508-784-12 PIN, CONNECTOR 5MM PITCH 1P

< DIODE >

D1701 8-719-991-33 DIODE 1SS133T-77

D1702 8-719-110-88 DIODE RD39ES-B2

D1703 8-719-110-88 DIODE RD39ES-B2

D1801 8-719-110-17 DIODE RD10ESB2

D1802 8-719-110-17 DIODE RD10ESB2

D1803 8-719-110-17 DIODE RD10ESB2

D1840 8-719-302-43 DIODE EL1Z

D1841 8-719-991-33 DIODE 1SS133T-77

D1901 8-719-991-33 DIODE 1SS133T-77

D1902 8-719-991-33 DIODE 1SS133T-77

D1903 8-719-991-33 DIODE 1SS133T-77

D1904 8-719-991-33 DIODE 1SS133T-77

D1905 8-719-923-60 DIODE MTZJ-T-77-9.1A

D1906 8-719-970-87 DIODE ERA38-06

D1907 8-719-970-87 DIODE ERA38-06

D1908 8-719-300-33 DIODE RU-3AM

D1909 8-719-991-33 DIODE 1SS133T-77

D1910 8-719-991-33 DIODE 1SS133T-77

< IC >

IC1801 8-759-603-37 IC M5216P

IC1901 8-759-450-95 IC LM393N

IC1902 8-759-008-70 IC LM358N

< COIL >

L1701 1-408-603-31 INDUCTOR 10UH

L1702 1-408-597-31 INDUCTOR 3.3UH

L1703 1-408-603-31 INDUCTOR 10UH

L1841 1-406-674-11 INDUCTOR 0UH

L1843 1-406-989-21 INDUCTOR 0UH


VM

L1901 1-406-677-11 INDUCTOR 0UH

< TRANSISTOR >



Q1703 8-729-017-05 TRANSISTOR 2SA1837


Q1706 8-729-017-06 TRANSISTOR 2SC4793

Q1708 8-729-216-22 TRANSISTOR 2SA1162-G



Q1840 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR

Q1841 8-729-931-45 TRANSISTOR IRF614-LF



Q1903 8-729-043-95 TRANSISTOR 2SC3840(3)





< RESISTOR >

R1701 1-216-049-00 RES,CHIP 1K 5% 1/10W

R1702 1-216-049-00 RES,CHIP 1K 5% 1/10W

R1703 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R1704 1-216-045-00 RES,CHIP 680 5% 1/10W

R1705 1-247-815-91 CARBON 220 5% 1/4W

R1706 1-247-815-91 CARBON 220 5% 1/4W

R1708 1-216-035-00 RES,CHIP 270 5% 1/10W

R1712 1-260-311-11 CARBON 39 5% 1/2W

R1713 1-249-384-11 CARBON 1.8 5% 1/4W F

R1714 1-249-414-11 CARBON 560 5% 1/4W F

R1715 1-249-432-11 CARBON 18K 5% 1/4W

R1716 1-249-417-11 CARBON 1K 5% 1/4W F

R1717 1-215-913-11 METAL OXIDE 220 5% 3W F

R1718 1-249-432-11 CARBON 18K 5% 1/4W

R1719 1-249-384-11 CARBON 1.8 5% 1/4W F

R1720 1-249-400-11 CARBON 39 5% 1/4W F

R1721 1-249-414-11 CARBON 560 5% 1/4W

R1722 1-216-017-91 RES,CHIP 47 5% 1/10W

R1724 1-216-017-91 RES,CHIP 47 5% 1/10W

R1725 1-215-887-00 METAL OXIDE 150 5% 2W F

R1728 1-216-037-00 RES,CHIP 330 5% 1/10W

R1729 1-216-041-00 RES,CHIP 470 5% 1/10W

R1730 1-216-059-00 RES,CHIP 2.7K 5% 1/10W

R1731 1-249-411-11 CARBON 330 5% 1/4W

R1751 1-216-049-71 RES,CHIP 1K 5% 1/10W

67

VM H1


R1752 1-216-049-71 RES,CHIP 1K 5% 1/10W

R1753 1-216-049-71 RES,CHIP 1K 5% 1/10W

R1805 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1806 1-216-117-00 RES,CHIP 680K 5% 1/10W

R1807 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1808 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1809 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1810 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1841 1-216-097-00 RES,CHIP 100K 5% 1/10W

R1842 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R1843 1-260-111-11 CARBON 10K 5% 1/2W

R1844 1-216-061-00 RES,CHIP 3.3K 5% 1/10W

R1846 1-260-111-11 CARBON 10K 5% 1/2W

R1847 1-215-886-11 METAL OXIDE 100 5% 2W F

R1848 1-215-875-11 METAL OXIDE 10K 5% 1W F

R1901 1-249-441-11 CARBON 100K 5% 1/4W

R1902 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1903 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1904 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1905 1-216-097-00 RES,CHIP 100K 5% 1/10W

R1906 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1907 1-216-097-00 RES,CHIP 100K 5% 1/10W

R1908 1-216-033-00 RES,CHIP 220 5% 1/10W

R1909 1-215-493-00 METAL 1M 1% 1/4W

R1910 1-216-295-00 SHORT 0

R1911 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1912 1-216-121-91 RES,CHIP 1M 5% 1/10W

R1913 1-216-049-00 RES,CHIP 1K 5% 1/10W

R1914 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R1915 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1916 1-216-675-11 METAL CHIP 10K 0.50% 1/10W

R1917 1-216-687-11 METAL CHIP 33K 0.50% 1/10W

R1921 1-215-896-51 METAL OXIDE 4.7K 5% 2W F

R1922 1-215-878-00 METAL OXIDE 33K 5% 1W F

R1923 1-216-097-00 RES,CHIP 100K 5% 1/10W

R1924 1-216-097-00 RES,CHIP 100K 5% 1/10W

R1925 1-216-097-00 RES,CHIP 100K 5% 1/10W

R1951 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1952 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R1953 1-216-081-00 RES,CHIP 22K 5% 1/10W

R1954 1-216-097-00 RES,CHIP 100K 5% 1/10W

R1955 1-216-089-00 RES,CHIP 47K 5% 1/10W

R1956 1-216-113-00 RES,CHIP 470K 5% 1/10W

R1957 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1958 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R1959 1-216-065-00 RES,CHIP 4.7K 5% 1/10W

R1960 1-216-113-00 RES,CHIP 470K 5% 1/10W




R1961 1-216-097-00 RES,CHIP 100K 5% 1/10W

R1962 1-216-101-00 RES,CHIP 150K 5% 1/10W

R1963 1-216-081-00 RES,CHIP 22K 5% 1/10W

R1964 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R1965 1-216-081-00 RES,CHIP 22K 5% 1/10W

R1966 1-216-081-00 RES,CHIP 22K 5% 1/10W

R1967 1-215-876-00 METAL OXIDE 15K 5% 1W F

R1968 1-249-416-11 CARBON 820 5% 1/4W

R1969 1-215-870-11 METAL OXIDE 1.5K 5% 1W F

< TRANSFORMER >

T1901 1-424-584-11 TRANSFORMER, DYNAMIC FOCUS

*********************************************************************

*A-1646-160-A H1 BOARD, COMPLETE

*******************

< CAPACITOR >

C902 1-137-372-11 FILM 0.022MF 5% 50V

C903 1-137-372-11 FILM 0.022MF 5% 50V

C904 1-104-665-11 ELECT 100MF 20% 25V

C905 1-126-964-11 ELECT 10MF 20% 50V

C907 1-126-960-11 ELECT 1MF 20% 50V

C908 1-126-960-11 ELECT 1MF 20% 50V

C911 1-102-074-00 CERAMIC 0.001MF 10% 50V

C912 1-102-074-00 CERAMIC 0.001MF 10% 50V

< CONNECTOR >

CN603 £ *1-580-844-11 PIN, CONNECTOR (POWER)

CN604 £ *1-695-292-11 PIN, CONNECTOR (POWER)

CN900 1-779-947-11 TERMINAL BLOCK S




< DIODE >

D901 8-719-302-45 DIODE SEL1210S-D

4-203-258-01 HOLDER LED (D901)

D902 8-719-929-15 DIODE HZS9.INBZ

D903 8-719-929-15 DIODE HZS9.INBZ

D904 8-719-109-97 DIODE RD6.8ES-B2

D905 8-719-109-97 DIODE RD6.8ES-B2

D906 8-719-923-60 DIODE MTZJ-T-77-9.1A

D907 8-719-923-60 DIODE MTZJ-T-77-9.1A

D908 8-719-923-60 DIODE MTZJ-T-77-9.1A

68




< FUSE >

F601 £ 1-576-232-21 FUSE (H.B.C.) 5AMP 250V

£ 1-535-725-11 FUSE HOLDER (F601)

< IC >

IC900 8-742-014-11 HYB IC SBX1981-51

< SOCKET >

H1


S1


C1113 1-104-664-11 ELECT 47MF 20% 25V


C1115 1-104-664-11 ELECT 47MF 20% 25V



C1122 1-104-664-11 ELECT 47MF 20% 25V




J900 1-764-606-11 JACK

< COIL >




C1132 1-104-664-11 ELECT 47MF 20% 25V


L900 1-412-531-31 INDUCTOR 33UH

L901 1-412-531-31 INDUCTOR 33UH

L902 1-408-603-31 INDUCTOR 10UH

L903 1-408-603-31 INDUCTOR 10UH

< RESISTOR >

R900 1-247-807-31 CARBON 100 5% 1/4W

R901 1-249-426-11 CARBON 5.6K 5% 1/4W

R902 1-249-437-11 CARBON 47K 5% 1/4W

R903 1-260-091-11 CARBON 220 5% 1/2W

R904 1-260-091-11 CARBON 220 5% 1/2W

R908 1-249-401-11 CARBON 47 5% 1/4W

R909 1-247-895-91 CARBON 470K 5% 1/4W

R910 1-247-895-91 CARBON 470K 5% 1/4W

R911 1-535-465-11 LEAD, JUMPER (5.0MM)

R912 1-249-422-11 CARBON 2.7K 5% 1/4W

R913 1-249-429-11 CARBON 10K 5% 1/4W

R914 1-247-863-91 CARBON 22K 5% 1/4W

< SWITCH >

S601 £ 1-571-433-21 SWITCH, PUSH (AC POWER)

S900 1-692-979-21 SWITCH, TACTILE

S901 1-692-979-21 SWITCH, TACTILE

S902 1-692-979-21 SWITCH, TACTILE

*********************************************************************

*A-1652-054-A S1 BOARD,COMPLETE

*****************

< CAPACITOR >





C1109 1-104-664-11 ELECT 47MF 20% 25V







C1149 1-126-963-11 ELECT 4.7MF 20% 50V

C1150 1-126-963-11 ELECT 4.7MF 20% 50V

C1151 1-104-664-11 ELECT 47MF 20% 25V


< CONNECTOR >


< DIODE >

D1101 8-719-066-72 DIODE BB135

< FERRITE BEAD >

FB1101 1-410-396-41 FERRITE 0.45UH

FB1102 1-410-396-41 FERRITE 0.45UH

FB1103 1-410-396-41 FERRITE 0.45UH

FB1104 1-410-396-41 FERRITE 0.45UH

FB1105 1-410-396-41 FERRITE 0.45UH

FB1110 1-412-002-31 INDUCTOR CHIP 4.7UH



< IC >

IC1101 8-759-466-48 IC TDA9875P

IC1102 8-759-100-96 IC UPC4558G2

IC1103 8-759-394-57 IC PST593C-MMP-4P

69

S1


< COIL >

L1101 1-408-596-31 INDUCTOR 2.7UH

L1114 1-410-671-31 INDUCTOR 47UH

L1115 1-408-599-31 INDUCTOR 4.7UH

L1116 1-408-599-31 INDUCTOR 4.7UH

< RESISTOR >

JR1105 1-216-295-00 SHORT 0

JR1112 1-216-295-71 CONDUCTOR CHIP

JR1113 1-216-295-71 CONDUCTOR CHIP

R1101 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1102 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1103 1-216-035-00 RES,CHIP 270 5% 1/10W

R1105 1-216-035-00 RES,CHIP 270 5% 1/10W

R1110 1-216-025-00 RES,CHIP 100 5% 1/10W

R1111 1-216-025-00 RES,CHIP 100 5% 1/10W

R1113 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1116 1-216-689-11 METAL CHIP 39K. 50% 1/10W

R1117 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1118 1-216-682-11 METAL CHIP 20K 0.50% 1/10W

R1121 1-216-065-71 RES,CHIP 4.7K 5% 1/10W

R1122 1-216-065-71 RES,CHIP 4.7K 5% 1/10W

R1123 1-216-065-71 RES,CHIP 4.7K 5% 1/10W

R1124 1-216-073-71 RES,CHIP 10K 5% 1/10W

R1125 1-216-065-71 RES,CHIP 4.7K 5% 1/10W

R1126 1-216-073-71 RES,CHIP 10K 5% 1/10W

R1164 1-216-073-00 RES,CHIP 10K 5% 1/10W

R1174 1-216-085-00 RES,CHIP 33K 5% 1/10W

R1175 1-216-085-00 RES,CHIP 33K 5% 1/10W

R1176 1-216-085-00 RES,CHIP 33K 5% 1/10W

R1177 1-216-085-00 RES,CHIP 33K 5% 1/10W

R1178 1-216-073-71 RES,CHIP 10K 5% 1/10W

< CRYSTAL >

X1101 1-767-813-21 VIBRATOR, CRYSTAL




MISCELLANEOUS

**************



1-452-032-00 MAGNET, DISC; 10MM Ø

1-452-094-00 MAGNET, ROTATABLE DISC; 15MM Ø

£ 8-453-005-21 NECK ASSY (NA297-M2) (KV-29K5K)


(KV-25K5K)


(KV-29K5K)

1-505-484-11 SPEAKER (2.6CM)

1-505-674-11 SPEAKER MID RANGE (8CM)

1-505-673-11 SPEAKER WOOFER (10CM)

£ 1-571-433-21 SWITCH, PUSH (AC POWER)

£ 1-765-286-11 CORD, POWER

8-598-432-00 TUNER (FSS-BTP-AC411)

£ 8-733-254-05 PICTURE TUBE (SD-257) (M60LCS60X) (KV-25K5K)

£ 8-733-856-05 PICTURE TUBE (SD-269) (M68LCT60X) (KV-29K5K)

£ 8-451-404-23 DEFLECTION YOKE (Y25GXABA) (KV-25K5K) ,

£ 8-451-466-11 DEFLECTION YOKE (Y29GXC2B) (KV-29K5K)

£ 8-733-254-76 ITC (KV-25K5K)

£ 8-733-856-75 ITC (KV-29K5K)

**********************************************************************

ACCESSORIES AND PACKAGING MATERIALS

***********************************

4-395-957-01 BAG, PROTECTION

4-203-677-01 INDIVIDUAL CARTON (KV-25K5K)

4-203-670-01 INDIVIDUAL CARTON (KV-29K5K)

4-203-678-01 CUSHION (UPPER) (ASSY) (KV-25K5K)

4-203-671-01 CUSHION (UPPER) (ASSY) (KV-29K5K)

4-203-681-01 CUSHION (LOWER) (ASSY) (KV-25K5K)

4-203-674-01 CUSHION (LOWER) (ASSY) (KV-29K5K)

4-204-276-91 MANUAL, INSTRUCTION (CZECH/ENGLISH/POLISH)

REMOTE COMMANDER

****************

1-475-765-11 COMMANDER STANDARD TYPE (RM-883)

********************************************************************

English

98DP7114-1

Printed in U.K.

©

1998.4

9-974-970-01

Sony Corporation

Sony UK

Service Promotions Dept.

70

No results