Electronics Line iconnect Installation manual

Installation Manual
For quick installation information please refer to the iConnect
Quick Start Installation Guide provided on our website: www.electronics-line.com
Table of Contents
1.
Introduction ..................................................................................................................................... 1
1.1.
Documentation Conventions............................................................................................................... 1
1.2.
Specifications ................................................................................................................................... 2
1.3.
System Overview .............................................................................................................................. 3
1.4.
Hardware Layout .............................................................................................................................. 4
2.
System Installation .......................................................................................................................... 7
2.1.
Pre-Installation Planning .................................................................................................................... 7
2.2.
Installation Procedure ....................................................................................................................... 8
2.3.
Back Tamper .................................................................................................................................. 11
2.4.
Internet Communication Setup ......................................................................................................... 12
3.
Basic System Operation .................................................................................................................. 13
3.1.
Front Panel Layout .......................................................................................................................... 13
3.2.
Front Panel System Status LEDs ....................................................................................................... 13
3.3.
Front Panel Keypad and Wireless LCD Keypad .................................................................................... 13
3.4.
LCD Display ................................................................................................................................... 14
3.5.
Audible Notification ......................................................................................................................... 15
3.6.
Arming and Disarming ..................................................................................................................... 16
3.7.
4.
Additional Arming Options ............................................................................................................... 18
Advanced System Operation ........................................................................................................... 20
4.1.
Menu Navigation ............................................................................................................................. 20
4.2.
Cancel Report................................................................................................................................. 20
4.3.
Zone Bypassing/Unbypassing ........................................................................................................... 21
4.4.
User Codes .................................................................................................................................... 21
4.5.
Follow-Me ...................................................................................................................................... 23
4.6.
Event Log ...................................................................................................................................... 23
4.7.
5.
Service Menu ................................................................................................................................. 24
Telecontrol and Two-Way Audio ..................................................................................................... 29
5.1.
Incoming Calls ............................................................................................................................... 29
5.2.
Outgoing Calls ................................................................................................................................ 31
6.
Home Automation and PGM Control ................................................................................................ 33
6.1.
Keypad Control............................................................................................................................... 33
6.2.
Keyfob Control ............................................................................................................................... 33
6.3.
Telephone Control........................................................................................................................... 33
6.4.
Scheduling (not relevant to PGM) ..................................................................................................... 34
7.
Devices ........................................................................................................................................... 35
7.1.
Device Descriptors .......................................................................................................................... 35
7.2.
Wireless Devices............................................................................................................................. 35
7.3.
Zones............................................................................................................................................ 36
7.4.
Keyfobs ......................................................................................................................................... 40
7.5.
Wireless Keypads............................................................................................................................ 41
7.6.
Repeaters ...................................................................................................................................... 41
7.7.
Wireless Siren ................................................................................................................................ 41
7.8.
Smartkeys ..................................................................................................................................... 42
8.
Entry/Exit Timers and System Tones .............................................................................................. 43
8.1.
Entry/Exit Delay ............................................................................................................................. 43
8.2.
Arm on Exit .................................................................................................................................... 43
8.3.
Supplementary Entry Delay.............................................................................................................. 43
ii
8.4.
Entry Deviation .............................................................................................................................. 43
8.5.
Arming Tones ................................................................................................................................ 43
8.6.
Home Automation Tones ................................................................................................................. 44
8.7.
System Trouble Tones..................................................................................................................... 44
8.8.
9.
Tones Options ................................................................................................................................ 45
System Options ............................................................................................................................... 46
9.1.
Swinger Setting ............................................................................................................................. 46
9.2.
Code Lockout ................................................................................................................................. 46
9.3.
Arm/Disarm Options ....................................................................................................................... 46
9.4.
Panic Alarm ................................................................................................................................... 47
9.5.
AC Loss Delay ................................................................................................................................ 48
9.6.
Display Options .............................................................................................................................. 48
9.7.
PGM Output Options ....................................................................................................................... 49
9.8.
Guard Code ................................................................................................................................... 50
9.9.
"No Arm" Indication ........................................................................................................................ 51
9.10.
Jamming Detection ......................................................................................................................... 51
9.11.
"No Motion" Time ........................................................................................................................... 51
9.12.
Microphone/Speaker Options ........................................................................................................... 51
9.13.
Vocal Messages .............................................................................................................................. 52
9.14.
Installer Access .............................................................................................................................. 52
9.15.
Auto Log View ................................................................................................................................ 52
9.16.
Daylight Savings ............................................................................................................................ 52
9.17.
Standard Type ............................................................................................................................... 53
9.18.
Battery Type .................................................................................................................................. 54
9.19.
Report Fail Trouble ......................................................................................................................... 54
9.20.
Immediate Arming from WUApp ....................................................................................................... 54
9.21.
T014A Standard ............................................................................................................................. 54
9.22.
Alarm Memory Reset ...................................................................................................................... 54
10.
Communications .......................................................................................................................... 55
10.1.
System Reporting ........................................................................................................................... 55
10.2.
Report Cycles ................................................................................................................................ 56
10.3.
Vocal Message Dialer ...................................................................................................................... 57
10.4.
Remote Programming ..................................................................................................................... 58
10.5.
Service Call ................................................................................................................................... 59
10.6.
Communications Options ................................................................................................................. 60
10.7.
GSM Options.................................................................................................................................. 61
10.8.
TWA Event Report Options............................................................................................................... 63
10.9.
Event Options for Central Station Reporting ....................................................................................... 64
10.10.
Vocal Message Dialer Event Options .............................................................................................. 65
11.
Internet Options .......................................................................................................................... 67
11.1.
ELAS Connection Parameters ........................................................................................................... 67
11.2.
Control System Parameters ............................................................................................................. 67
11.3.
GPRS Network Parameters............................................................................................................... 68
11.4.
LAN Network Parameters ................................................................................................................. 68
12.
Home Automation Programming ................................................................................................. 70
12.1.
X10 Overview ................................................................................................................................ 70
12.2.
HA Units........................................................................................................................................ 70
12.3.
House Code ................................................................................................................................... 72
12.4.
HA Control..................................................................................................................................... 72
iii
13.
System Initialization................................................................................................................... 73
13.1.
Initialization ................................................................................................................................... 73
13.2.
Default Program Restore ................................................................................................................. 73
13.3.
Clear User Codes ............................................................................................................................ 73
13.4.
Clear Wireless Transmitters ............................................................................................................. 73
13.5.
Find Modules .................................................................................................................................. 73
Appendix A: Menu Structure .................................................................................................................. 74
Appendix B: Transmitter Installation ..................................................................................................... 81
PIR Detectors (EL-4755/EL-4755PI) ............................................................................................................. 81
PIR Detectors (EL-4745/EL-4745PI) ............................................................................................................. 84
Dual Magnetic Contact/Universal Transmitter (EL-4601DZ) ............................................................................. 87
Universal Transmitter (EL-4602) .................................................................................................................. 89
Vibration Detector (EL-4607) ...................................................................................................................... 90
Smoke Detector (EL-4703) ......................................................................................................................... 92
Keyfobs (EL-4714) ..................................................................................................................................... 98
Keyfobs (EL-4711M/P) ................................................................................................................................ 99
Wireless LCD Keypad (EL-4727) ................................................................................................................ 101
Gas Leak Detector (EL-4762) .................................................................................................................... 102
Carbon Monoxide Detector (EL-4764) ......................................................................................................... 105
Flood Detector (EL-4761) ......................................................................................................................... 109
Indoor Siren (EL-4723)............................................................................................................................. 111
Outdoor Siren and Strobe (EL-4726T) ........................................................................................................ 113
I/O Expander Module (EL-4770) ................................................................................................................ 115
Transmitter Specifications ......................................................................................................................... 120
Appendix C: Web User Application ........................................................................................................122
Appendix D: Event Table* .....................................................................................................................130
Appendix E: Zone Types ........................................................................................................................133
iv
1 Introduction
1.
Introduction
This manual is designed to help you install the iConnect
Control System1. We strongly urge you to read through this
manual, in its entirety, before beginning the installation process so that you can best understand all that this security
system has to offer. This manual is not intended for end user use. End users are encouraged to read the user manual
provided with the system. If you have any questions concerning any of the procedures described in this manual please
contact Electronics Line 3000 Ltd. at (+972-3) 963-7777.
1.1.
Documentation Conventions
Throughout the manual, we have tried to include all of the operating and programming functions using a similar
structure and order as they appear in the menu. A detailed explanation of how to navigate the Control System’s menu
is included in Menu Navigation. In order to simplify the procedures that appear in the rest of this manual, the
following conventions are used:
Table 1-1: Documentation Conventions
Item…
Description…
Select…
From the Event Log Menu, select
Clear Log.
Use the arrow keys to scroll through the options and press '√ʹ.
Enter the main menu by pressing '√ʹand entering your user code. Using the arrow keys,
navigate until you reach Event Log and press '√ʹ. Using the arrow keys, navigate until you
reach Clear Log and press '√ʹ.
The same as above only this time you are navigating through three menu levels.
From the Service menu, select Set
Time/Date, Set Date.
[7012]
[#5]
'√ʹ
5. Interface Test
Due to the
occurrence
The iConnect
Control System is …
Warning ……Do not test with
flame!
The shortcut to a specific menu item from the main menu. In this case, this is the shortcut for
Set Date. These appear in the procedures as an additional aid to menu navigation.
A shortcut to a specific item in a sub-menu. For example, [#5] is the shortcut to Bell enable
disable in the sub-menu that is opened once you have selected the detector you want to
program.
The symbol on a key that appears on the keypad
The text that actually appears on the LCD display (bold).
Important note, please pay attention.
Caution: description of a potentially hazardous situation.
Warning: description of a potentially hazardous situation that is a threat to human
life.
EN Note – restrictions and settings demanded by the standard EN 50131-1
1
The terms Control System, Control Panel, and CP refer to the same notion.
iConnect
Installation Manual
1
1 Introduction
1.2.
Specifications
General
Zones: 32 wireless zones, 2 hardwire zones (Zone 33-34), or zones 1 –
8 as wired zones, zones 9 – 32 as wireless and 2 hardwire zone (Zone
33, 34).
Wireless Keyfobs: 19 (Controlled or Non-controlled)
Wireless Keypads: up to 4
Wireless Repeaters: up to 4
Smartkeys: 12 (Controlled or Non-controlled)
Wireless I/O Zone Expanders: 2
Wireless Siren: up to 4
Wired Siren: 1
User Codes: 32
Arming Methods: Full, Part or Perimeter
Event Log: 1022 event capacity, time and date stamped
Weight: 1.350g
Dimensions: 270 x 222 x 50mm
Communications
Event Reporting Accounts: up to 6, including Central Station, FollowMe, and Voice
Telephone Numbers: 6 event reporting accounts, RP Callback,
Service Call
Communication Interface Options: GPRS/Ethernet or Ethernet/PSTN
Home Automation
Control Medium: Power-line carrier
Protocol: X10
HA Units: 16 individually addressed
Receiver
Type: Super-heterodyne, fixed frequency
Frequency: 868MHz, 433MHz (optional)
Data Encryption: SecuriCode™
Electrical*
Power Input: 230VAC, 50Hz
AC Current Consumption (GPRS Configuration): 30mA (alarm),
17mA (standby)
AC Current Consumption (Ethernet Configuration): 35mA (alarm),
17mA (standby)
DC Current Consumption (GPRS Configuration): 280mA (alarm),
130mA (standby)
DC Current Consumption (Ethernet Configuration): 330mA (alarm),
135mA (standby)
Maximum Auxiliary Output Current Rating : 50mA
Battery low: below 7.15V
Backup Battery Pack: 1 x 7.2V/1.8Ah Part No. BT5780
(6 x 1.2V Ni-MH rechargeable cells, size AA)
The maximum charging current for the BT-5780 is 5.4A
For EN-50131 standard, 1.5Ah battery is mandatory
Fuse Ratings: 63mA/250V for 230VAC – Part No. EF1063,
PGM Relay Output Contact Rating: 100mA (max. load)
Built-in Siren: 93dB @ 10ft
Tamper Switch: N.C.
Operating Temperature: 0-60°C /32-140°F
Complies with EN-50131-3 Grade 2 Class II
Power Supply Type A
Power connection to the unit should be according to the national electrical code for permanent installation.
The power supply should be fed from a readily accessible disconnect device.
If the unit is permanently wired to the mains power, use a 2-pole disconnect device (15A max.) and the wires should be min.
0.75mm2 in a conduit of at least 16mm.
If the mains power is connected with a plug, the plug should be indicated as the disconnecting device and the socket shall be
max. 2m from the Control System.
Batteries shall be provided by a distributor and replaced by authorized service personnel.
The backup battery pack should be replaced every five years.
Batteries should be stored in a cool, dry place.
**
2
The measurements are with fully charged battery. AC current was measured on fuse F1 and DC current was measured on fuse F2.
iConnect
Installation Manual
1 Introduction
1.3.
System Overview
The iConnect
Control System is a full-featured 2-way wireless control system that is expected to provide a solution
to the needs of most residential installations. This system has been developed based upon a design concept geared
towards easy installation and use. With this in mind, the user interface is based on a simple, menu-driven model that
Control System
suits the essential requirements of both the user and installer alike. You can program the iConnect
on-site using the on-Front Panel keypad or PC, or off-site via a PC using local programming option of the Remote
Programmer.
Figure 1-1 shows the components that make up the system and the system’s interaction with external communication
networks for all the configurations.
Figure 1-1: System Architecture
See Figure 1-2
The system offers GPRS and Ethernet network connectivity, providing high-speed central station reporting via a GPRS
or Ethernet interface.
iConnect
Installation Manual
3
1 Introduction
The Electronics Line Application Server (ELAS) handles all communication between the system, service providers and
web users enabling monitoring and control to be performed via the Web.
Central station communication and remote parameters programming and maintenance employ Ethernet, GPRS, GSM or
standard PSTN communication. SMS messaging provides an innovative method used for both central station and
Control System enabling the
Follow-Me user monitoring. Additionally, SMS messages can be sent to the iConnect
user to send commands to the system from anywhere on the planet.
1.
2.
3.
4.
5.
Contrast LCD
Speaker
Bell
Jumper for siren volume (see
Table 1-2, Jumper Settings)
Flat Cable
Figure 1-2: Main Panel
The Main panel has connectors to the built-in Siren and the Speaker.
1.4.
Hardware Layout
The aim of this section is to acquaint you with the various circuits that make up the system. Apart from the Main Panel,
each peripheral module is available as an optional extra designed for installation inside the plastic housing.
1.
2.
3.
Power and Connection board
Communication module (GPRS + GSM +
LAN)
Backup battery pack
Figure 1-3: System Layout
1.4.1.
Power Supply and Connection Board
The Power and Connection Board is the brain of the system and connects to various peripheral modules using a
number of interface connectors. Additionally the Power and Connection Board includes a programmable output, and
hardwired zones input.
4
iConnect
Installation Manual
1 Introduction
1.
2.
3.
4.
5.
6.
Interphone module connector
Flat-cable interface connector to communication
module
Programmable relay output (100mA max. load)
and jumpers for PGM control (JP3, JP4)
Wired detector zone (Zone 33, 34)
System bus terminal block (Wired Zone
Module)
Flat-cable interface connector to Main board
(LCD keypad, built-in speaker, microphone and
siren)
7.
8.
Front tamper switch
Interface connector to Home Automation
module
9. AC power terminal block
10. Home Automation module terminal block
11. AC power protection fuse
12. Backup battery connector and jumper for
backup battery discharge protection (JP2)
Figure 1-4: Power Supply and Connection Board
Table 1-2: Jumper Settings
JPI
JP2
1.4.2.
Siren Strength (see
Figure 1-2, Main
Panel)
Backup Battery
Protection
JP3
PGM 1
JP4
PGM 2
Installed: 105dB
Removed: 85dB
Installed: Activated (If a continuous AC power outage occurs, the panel
automatically disconnects the battery when its backup battery voltage drops to a
certain level, in order to prevent "deep discharge” that may damage the battery)
Remove: Disabled (The battery may be totally discharged during continuous AC
failure; therefore battery replacement may be required.
Installed: Open Connector
Removed: Dry Contact
Installed: Open Connector
Removed: Dry Contact
Home Automation Module
The Home Automation module provides the system with an interface to the power-line network, enabling control over
16 home automation units employing the X10 protocol via an external or internal Power-line Interface (PLI), depending
on your system configuration. The illustrations below show the HA module used in the systems with internal PLI (for
use in 220V, 50Hz A.C. power systems), and with external PLI (for use in 110V, 60Hz A.C. power systems).
iConnect
Installation Manual
5
1 Introduction
1.
2.
3.
4.
5.
Power-line terminal connections to Main
Board (1 - Neutral; 2 - Live)
Fuse
LED Indicator
Flash programming connector
Interface connector to Main Board
Figure 1-5: Home Automation Module (Internal PLI
Module)
1.
2.
3.
4.
External PLI connector
LED indicator
Flash programming connector
Interface connector to Main Board
Figure 1-6: Home Automation Module (External PLI
Module)
For external X10 PLI, we recommend to use the two-way TTL/CMOS interface such as
XM10E module connected to the HA module with an RJ11 cable wired, as shown below.
Figure 1-7: RJ11 wiring diagram
1.4.3.
GPRS/LAN Communication Module
The GPRS/LAN Communication module enables the iConnect
Control System to communicate to the WEB via
cellular networks, perform remote firmware update, send or receive SMS messages, and implement cellular 2-way
audio communication.
1.4.4.
LAN/PSTN Module
Control System to communicate to the WEB via
The LAN/PSTN Communication module enables the iConnect
Ethernet, perform remote firmware update, and implement PSTN backup communication with event reporting and
Two-Way Audio (TWA) control.
Do not use VoIP phone lines for communication to the central monitoring station. In certain
cases the system may not transmit alarm signals successfully over the VoIP network.
To reduce the risk of fire, use only No. 26AWG or larger telecommunication wire.
6
iConnect
Installation Manual
2 System Installation
2.
System Installation
The following chapter explains how to install the system and provides guidelines and tips on how to optimize the
installation. It is recommended that you familiarize yourself with the various circuit boards that make up the system –
see p. 4, 1.4 Hardware Layout.
2.1.
Pre-Installation Planning
Before starting the installation procedure, it is worthwhile to draw a rough sketch of the building and determine the
required position for the Control System and each wireless device.
When deciding on the placement for installation, consider the following:
• Mount the Control System in a location with easy access to telephone and power connections.
• Mount the Control System in a location that provides easy connection to the router.
• For best performance of the GPRS Communication module, the Control System should be mounted in a
position where the GSM signal is strong.
• Refer to the following section in order to choose the optimal location for wireless devices in relation to the
Control System.
2.1.1.
Wireless Installation Guidelines
In order to optimize wireless communication, consider the following guidelines:
• Whenever possible, mount the Control System centrally in relation to wireless detectors.
• Avoid installation in close proximity to sources of high noise or radio frequency interference. For example,
metal air conditioner/heater ducts and circuit breaker boxes.
• Minimize the distance between the Control System and transmitters.
• Minimize the number of obstacles between the Control System and transmitters.
Figure 2-1: Minimizing Obstacles
• Metal based construction materials, such as steel reinforced concrete walls, reduce the range of radio
transmissions.
Figure 2-2: Considering Construction Materials
• The reduction of the RF signals’ strength is directly proportional to the thickness of the obstacle, assuming
that the obstacles are of identical material.
Figure 2-3: Considering Thickness of Obstacles
iConnect
Installation Manual
7
2 System Installation
2.2.
Installation Procedure
The iConnect
Control System Kit consists of:
• Control System
• Quick Start Installation Guide
• Quick User Guide
• Mounting Guide
• Plastic bag with Cable Clamp, Cable Clamp screw, Housing Screw,
After unpacking the kit and making certain that you have all the necessary equipment, it is recommended that you
install the system as follows:
STEP 1: Temporarily power up the system and install the SIM card.
STEP 2: Selecting language and defaults
STEP 3: Establishing an RF wireless network.
STEP 4: Register the transmitters.
STEP 5: Test the chosen mounting location.
STEP 6: Program the relevant Internet options.
STEP 7: Permanently install the Control System and transmitters.
2.2.1.
Step 1 – Temporarily Power up the System and Install SIM Card
In order to register and test transmitters, it is necessary to temporarily power up the Control System before
permanently installing it.
1.
Remove the housing screw located at the bottom of the front cover as shown in Figure 2-4.
2.
Insert a screwdriver between the front and back panels of the housing; carefully twist it to release the tabs.
3.
Lift the front cover away from the back of the housing. You will notice that the front cover is attached to the back
with two fastening bands and the hardwire LCD keypad’s flat cable.
Figure 2-4: Opening the Housing
The Control System is supplied without AC cable. Please use Standard Two-Pin European
Plug cable only. For the Cable Clamp, use the screw and the washer supplied in your kit to
replace the PCB screw.
4.
Open the SIM card holder on the Communication Board, insert the SIM card.
5.
Close the Housing.
6.
Plug the Power AC cable into the wall outlet.
In five minutes since power-up, the siren will sound. To silence the siren, enter your user
code (default user code is 1234).
At this stage, do not connect the backup battery. Ignore any trouble conditions that may appear on the LCD Display
(e.g. Low Battery)
8
iConnect
Installation Manual
2 System Installation
2.2.2.
Step 2: Selecting Language and Defaults
The Control System supports several languages. Upon power-up the control system automatically opens the language
and default settings menu. Language and defaults settings must be defined before any configuration parameters are set
or any transmitters registered.
To define language and defaults settings:
1.
Press '√ʹ.
2.
Enter your Installer code (the default Installer code is 1111).
3.
From the Programming menu, select Devices [971] (Programming, Initialize, Init. All).
4.
Select the default setting and press '√ʹ.
5.
Select a language (Voice + LCD display) and press '√ʹ.
6.
Press '√ʹ once more to restart the Control System.
2.2.3.
Step 3 – Establishing an RF Wireless Network
In order to provide the best possible installation environment you need to establish an effective RF wireless network.
RF wireless network establishment should be performed prior to any wireless device allocation in order to select the
best RF channel according to the levels of background ʺnoiseʺ in the installation environment. This procedure helps the
devices, once registered, to effectively deal with any high levels of background noise that may be generated by
additional appliances operating at similar frequencies in the installation area.
To establish an RF wireless network:
1.
Press '√ʹ.
2.
Enter your Installer code.
3.
From the Programming menu, select Devices [9191] (Programming, Devices, RF Network Establishment).
4.
Press '√ʹ. The Control System scans several RF channels and selects the channel with lower ʺnoise levelʺ.
5.
When Save? is displayed on the Control System’s LCD, press '√ʹ.
Network establishment must be performed prior to wireless device allocation.
If required, after the initial network is established, you can calibrate the receiver again only after deleting
the network by selecting [9193] (Programming, Devices, RF Network, Delete Network).
2.2.4.
Step 4 – Registering Transmitters
For the Control System to recognize a device, its transmitter must be registered. In general terms, transmitter
registration means sending two transmissions from a device when the Control System is in Registration mode.
To register a device:
1.
Press '√ʹ.
2.
Enter your Installer code.
3.
Enter [91] (Programming, Devices) to enter the Devices menu.
4.
Press the menu navigation keys (/), until the type of device you want to register appears on the LCD display
(e.g. Zones or Keypads).
5.
Press '√ʹ.
6.
Press the menu navigation keys (/), until the exact device you want to register appears on the LCD display
(e.g. Zone 3 or Keypad 2).
7.
Press '√ʹ. If a device has not been registered at the chosen location, the Control System initiates Registration mode.
During Registration mode, the system waits for two transmissions from the device.
If a device has already been registered at the selected location, or in another location, the system will not
initiate Registration mode.
8.
Send two transmissions from the device – refer to each device’s installation instructions in Appendix B for
further details.
9.
When Save? is displayed on the Control System’s LCD, press '√ʹ.
The display automatically switches to the next option for that device. For example, pressing '√ʹ to
confirm Zone registration automatically moves you to the Zone Type option.
10.
Continue entering other parameters for the chosen device.
iConnect
Installation Manual
9
2 System Installation
2.2.5.
Step 4 – Testing the Chosen Mounting Location
Once all of the transmitters are registered, it is recommended that you test the chosen mounting locations before
permanently mounting the Control System and wireless devices. You can test the transmitter signal strength using the
Test features.
To test transmitter signal strength:
1.
Press '√ʹ.
2.
Enter your Installer code.
3.
Enter [7042] (Service, Transmitters, TX Test) to initiate TX Test mode.
4.
Activate the transmitter you wish to test; the transmitter’s details appear on the Control System’s LCD.
Additionally, between one and four tones are sounded to indicate the transmitter’s signal strength. If four
tones are sounded, the transmitter is in the best possible location – see Transmitters for further information.
5.
After you have tested each transmitter, press Χ to exit TX Test mode.
When using the GPRS Module, test the GSM signal strength.
To test the GSM signal strength:
1.
Press '√ʹ.
2.
Enter your Installer code.
3.
Enter [706] (Service, GSM Signal); the signal strength of the cellular network is displayed – see p. 27, 4.7.10 GSM
Signal Strength for further information.
4.
Check the RSSI (Received Signal Strength Indication) level of the installation environment using the system’s
RSSI meter.
To view the Environmental RSSI level reading:
• Enter [7044] (Service, Transmitters, Env. RSSI); the current RSSI level is displayed – see p.26,
Environmental RSSI, for further information.
2.2.6.
Step 5 – Programming Internet Options
Internet settings are mostly pre-programmed in the Control System’s default settings. The only settings you need to
program are the Control System’s ID & Password (provided by the ELAS administrator). The following procedures
explain how to program the Control System’s ID (CPID) and Password. For further information regarding other
Internet options and settings, see p. 67, 11 Internet Options.
To program the CPID:
1.
Press '√ʹ.
2.
Enter your Installer code.
3.
Enter [9573] (Programming, Communications, Internet, CPID).
4.
Enter an ID using the alphanumeric keypad. The ID length must be six up to sixteen characters. The ID must
begin with a letter.
5.
Press '√ʹ.
To program the Control System’s password:
1.
Press '√ʹ.
2.
Enter your Installer code.
3.
Enter [9574] (Programming, Communications, Internet, CP Password).
4.
Enter a password using the alphanumeric keypad.
5.
Press '√ʹ.
The password length must be six up to sixteen characters. The password must begin with a letter.
10
iConnect
Installation Manual
2 System Installation
2.2.7.
Step 6 – Installing the Control System and Transmitters
Having chosen and tested the mounting location of the Control System and each transmitter, you are now ready to
permanently install the system.
To permanently install the transmitters, refer to each device’s installation instructions (in Appendix B of this manual or
supplied individually with each product).
To install the Control System:
1.
Disconnect AC power from the Control System.
2.
Open the housing as explained in Step 1 – Temporarily Power up the System and Install SIM Card.
3.
Remove the backup battery pack. If you want to install the Control System with back tamper, it is also necessary
to disconnect the flat cable connecting the Main board to the front panel keypad and remove the Main board.
4.
Place the Control System in position against the wall and mark the upper and lower mounting holes. If using the
back tamper, also mark the hole for the back tamper screw.
5.
Install wall anchors in the appropriate positions.
6.
Thread any required cables through the wiring hole on the back cover (e.g. AC power, HA interface, Ethernet
cable, and telephone line) and make any necessary wiring connections:
a.
Connect the power cable to the AC power input on the Main board.
Always connect AC power before connecting the battery pack. Batteries are supplied
uncharged. When you first connect the battery, it is probable that the system will display a Low
Battery condition. Allow the battery to charge for at least 18 hours before use.
b.
7.
Connect the telephone line to the Telephone Line terminal block on the GPRS module (PSTN
connector) – see p. 6, 1.4.3 GPRS/LAN Communication Module.
Mount the Control System to the wall using four screws and insert the back tamper screw if required – see p.11,
2.3 Back Tamper.
The Control System must be mounted so that it shall withstand a force of at least three times
its own weight.
8.
Replace the Main Board and reconnect its peripheral modules.
9.
Connect the flat cable connecting the Main board to the front panel keypad and replace the front cover’s fastening
bands.
10.
Apply AC power.
Always connect AC power before connecting the battery pack. Batteries are supplied uncharged.
When you first connect the battery, it is probable that the system will display a Low Battery
condition. Allow the battery to charge for at least 18 hours before use.
11.
Connect the battery pack to the connector on the Main Board.
12.
Position the front cover’s top holding hooks onto the back cover and snap the front cover closed.
13.
After installing the Control System, perform the Find Modules function – see p. 73, 13.5 Find Modules.
2.3.
Back Tamper
The back tamper switch is an optional feature that provides an extra safeguard in the event that the Control System is
removed from the wall.
The back tamper switch is located on the rear side of the Control System’s Main Board and is constantly depressed by
the section of the back cover shown in Figure 2-5.
Figure 2-5: Perforated Back Tamper Release
For this feature to operate, you must insert a screw into the back tamper mounting hole – see p. 11, Step 6 – Installing
the Control System and Transmitters. When the Control System is removed from the wall, the screw causes the
perforated section of the plastic to break and remain attached to the wall. As a result, the back tamper switch is released
and an alarm is generated.
iConnect
Installation Manual
11
2 System Installation
2.4.
Internet Communication Setup
After you have powered up the system, the GPRS or LAN startup sequence (depending on your Control System
configuration) is initiated. During this sequence, the GPRS or Ethernet module receives the parameters programmed in
the Control System's Internet Options – p. 67, 11 Internet Options. After the startup sequence is complete, the GPRS or
LAN attempts to connect to the ELAS GPRS/LAN Proxy.
If the Control System is having difficulty connecting to ELAS, a trouble message is displayed. The following table
summarizes the trouble messages for this case.
Table 2-1: ELAS Connection Trouble Message
LCD display
SIM CARD TROUBLE
MEDIA LOSS
LAN MODULE
MEDIA LOSS GSM
MEDIA LOSS GPRS
MODULE
DEVICE TROUBLE
LAN MODULE
DEVICE TROUBLE GSM
DHCP ERROR
XML FAIL
Trouble condition
SIM card not recognized or incorrectly
programmed
LAN down
Restored by
Insertion of recognized SIM card
or correct programming.
LAN restore
Cellular network down
Wrong GPRS settings (APN, Password
etc.) or loss of GPRS service
Faulty Ethernet module
Cellular network restore
Correct GPRS settings or restored
GPRS service
Replacement of faulty module
Faulty GSM/GPRS module
IP parameters cannot be set because of
missing DHCP services
Control panel fails to communicate
with the XML Proxy
Replacement of faulty module
Change IP LAN settings or
restored DHCP service
Successful communication with
XML Proxy
In this case, check that the Control System’s Internet Options are correctly programmed. If you still experience
problems, the IP Protocol and GPRS settings must be checked.
To check the IP Protocol and GPRS/LAN settings:
1.
For GPRS settings, open the system housing and make sure a SIM Card with GPRS support is on the GPRS
module.
2.
Close the Housing and enter your Installer code.
3.
Enter [95112] (Programming, Communications, Accounts, Account 1, Protocol). If the setting is correct, you will
see IP Protocol.
4.
Exit this menu and Enter [95113] (Programming, Communications, Accounts, Account 1, Interface). If the setting
is correct, you will see GPRS or LAN, respectively.
When using a SIM card with a PIN code, the installer has to make sure that the PIN code
programmed in the Control System is the same as the SIM card's PIN code – see p. 62, 10.7.2
PIN Code.
12
iConnect
Installation Manual
3 Basic System Operation
3.
Basic System Operation
The iConnect
Control System is available with the LCD front panel configuration. Below you will find description of
the LCD front panel layout.
3.1.
Front Panel Layout
The front panel provides a detailed interface for operating and programming the system. The following diagram will
familiarize you with the various elements of the front panel.
LCD
Display
System
Status
LEDs
Menu
Navigation
Keys
Arming
Keys
Alphanumeric
Keypad
Figure 3-1: Front Panel
3.2.
Front Panel System Status LEDs
The two LEDs, OK and Arm Status, provide essential information on the status of the system.
Table 3-1: OK LED Indication
OK LED Status
Off
Green On
Green Flashing
Yellow On
Yellow Flashing (slow)
Yellow Flashing (fast)
Yellow Intermittent On/Off
Meaning
Both AC and Battery power are disconnected.
System Power Status is OK and there is System Trouble.
Open Zone. Check that the windows and doors are closed and no movement is detected by
the detectors within the protected area.
System Trouble.
Backup battery low or low battery from transmitters.
AC loss.
System Trouble in addition to AC loss/Low Battery.
Table 3-2: Arm Status LED Indication
LED Status
Off
Green On
Red Flashing
Meaning
The system is disarmed.
The system is armed.
An alarm has occurred. Alarm indication is cleared the next time you arm the system or
view the relevant event in the event log.
Alarm indication is not displayed after a silent panic alarm.
3.3.
Front Panel Keypad and Wireless LCD Keypad
The alphanumeric keypad on the front panel enables you to perform various operation and programming tasks. Apart
from the regular functions of a standard alphanumeric keypad, Full, Part, and Perimeter arming, Home Automation
and PGM control, the keypad offers a number of special functions.
iConnect
Installation Manual
13
3 Basic System Operation
In addition to the front panel keypad, you can install up to four, individually addressed, Wireless LCD keypads. The
layout of the Wireless LCD keypad is similar to the front panel keypad and most of the functionality is identical.
Table 3-3: Front Panel Keypad and Wireless LCD Keypad Functions
Key
Symbol used in the
text of this manual
1
Used to enter symbols in descriptor editing.
0
Used to enter symbols in descriptor editing.
Χ
Used to cancel the current selection.
Used to return to the previous menu level.
Used to enter Menu mode.
Used to select the current menu item.
Used to signify the end of an entered value.
Toggles status in Zone Bypass/Unbypass function.
Used to switch Home Automation units or PGM on.
In descriptor editing, used to insert a space before the current character
In phone number editing, used to enter "T", ",", "P", "+", "", "#".
In account number editing, used to enter Hexadecimal digits (A-F).
Toggles item descriptors and default names.
In the event log, toggles the time/date stamp.
Toggles AM and PM when setting the time in 12hr format.
Used to switch Home Automation units or PGM off
In descriptor and phone number editing, used to delete the current character.
'√ʹ
Special function
Used to scroll backwards in the current menu level.
For Global Chime and Message Center features, used to access shortcuts.
+ (Global Chime shortcut)
+ Χ (Record Message shortcut, front panel keypad only)
+ '√ʹ (Play Message shortcut, front panel keypad only)
Used to scroll forwards in the current menu level.
During standby, used to scroll through the list of system trouble conditions.
The Wireless LCD Keypad LEDs functionality is identical to those of the Front Panel keypad – see p. 13, 3.2 Front Panel
System Status LEDsError! Reference source not found. shows the layout of the LCD keypad:
3.4.
LCD Display
The LCD display provides you with a detailed interface for operation and programming.
Figure 3-2: Typical Standby Display
3.4.1.
Standby Mode
Standby mode can be defined as the state the system is in when it is disarmed and not in Menu mode. In Standby mode,
the armed status, system status or banner are displayed. If system status is normal, the current time is displayed.
Table 3-4: Armed Status
Item…
DISARMED
FULL ARMED
PART ARMED
PERIMETER ARMED
PART ARMED INST
PERIM ARMED INST
FULL ARMING
PART ARMING
PERIMETER ARMING
PART ARMING INST
PERIM ARMING INST
14
Description…
The system is disarmed.
The system has been armed using the displayed arming method.
The system has been armed using the displayed arming method with the
Instant arm feature activated.
The system is in the process of arming (displayed during exit delay).
The system is in the process of arming with the Instant arm feature activated.
iConnect
Installation Manual
3 Basic System Operation
Table 3-5: System Status
Item
ZONES IN ALARM
TAMPER ALARM
56 TO EXIT
11 TO DISARM
SYSTEM NOT READY
KEYPAD LOCKED
Description
Zones have been violated.
The system has been tampered with.
The exit delay is counting down (56 seconds remaining).
The entry delay is counting down (11 seconds remaining).
The system is not ready to arm, check that all doors and windows are closed.
Five unsuccessful attempts were made to enter a user code; the keypad is
locked for 30 minutes.
A trouble condition has been detected, press for further details.
SYSTEM TROUBLE
3.5.
Audible Notification
The following table is a summary of tones that audibly notify system status.
Table 3-6: Audible Notification
Status
Positive
Acknowledge
Negative
Acknowledge
Exit Delay/
Entry Delay
Chime
Arm
Disarm
Home Automation
System Trouble
3.5.1.
Tones
1 long tone.
Description
The preceding action was accepted.
5 low tones.
The preceding action was not accepted (e.g. an
incorrect user code entry).
The exit/entry delay is counting down.
The number of tones sounded during each delay is
determined in programming – see p. 43 8.5 Arming
Tones.
External Siren: 4 tones.
Internal Siren: 4 tones or
Continuous tones.
Continuous tones quicken
when there are 15 seconds
remaining and quicken again
when there are 5 seconds
remaining.
2-tone modulated sequence
(similar to a doorbell).
3-tone modulated sequence
(low to high) sounded twice
3-tone modulated sequence
(high to low).
Rapid 2-tone modulated
sequence.
4 rapid tones sounded once
per minute.
A zone with the Chime option enabled has been
opened – see p. 38 7.3.5 Chime .
The system has been armed using any of the arming
methods.
The system has been disarmed.
An HA unit has been turned On or Off using a
wireless keypad or keyfob – see p. 44 8.6 Home
Automation Tones .
A trouble condition has been detected, press for
further details. For Fire Trouble Tones, there is a
programmable option to repeat fire-related trouble
tones until the problem has been taken care of – see
p. 45, 8.7.3 Fire Trouble Tones.
System Trouble Tones
In the event of system trouble, the iConnect
Control System sounds a series of tones to alert the user. To silence these
tones, press and scroll through the system trouble list displayed on the LCD. When the trouble condition is restored,
it is removed from the system trouble list.
For this feature to function, Trouble Tones must be enabled in programming – see p. 44,
8.7.1 System Trouble Tones.
System trouble tones are not sounded from 10:00pm to 7:00am so as not to disturb household members who may be
asleep. However, you can program the system to immediately annunciate telephone trouble at all times – see p. 45, 8.7.2
Telephone Trouble Tones.
3.5.2.
Vocal Message Annunciation
Control System hardware support vocal annunciation of system status. If this
Certain versions of the iConnect
feature is enabled in programming (see p. 52, 9.13 Vocal Messages), the system plays short messages to indicate arming,
disarming, bypassed zones, system trouble, message waiting, and water alarm.
The availability of the Vocal Message annunciation feature is hardware dependent.
3.5.3.
Alarm Sounding Patterns
he following table summarizes the system’s various alarm patterns.
iConnect
Installation Manual
15
3 Basic System Operation
Table 3-7: Alarm Patterns
Alarm
Burglary
Fire
Gas
Medical
Flood/Environmental
3.6.
Alarm Pattern Description
ON (continuously)
ON - ON - ON, 1.5-second pause, ON - ON – ON...
ON - ON - ON - ON (short bursts), 5 second pause, ON - ON - ON
- ON...
ON (continuously) – only applicable for MedicalEmergency alarm
from zone
4 rapid tones sounded once per minute (same as Trouble tones)
Sounds
Siren
Siren
Siren
Siren
Buzzer
Arming and Disarming
The following section explains how to arm and disarm the Control System using the front panel keypad and wireless
LCD keypad.
3.6.1.
Arming
The iConnect
Control System offers three arming modes that you can define to suit the application. Figure 3-4
illustrates the three arming modes. In each diagram, the protected area is shaded.
Full Armed
Part Armed
Perimeter Armed
Figure 3-3: Arming Modes
The arming options are entirely flexible. You can program each detector to be included in any combination of the three
arming modes – see p. 37, 7.3.2 Arm Set. Additionally, each arming mode has a separate exit and entry delay.
Below you can see another, more complicated example of how can the premises be divided. In this example, the garage
is included in full + part + perimeter arming, the house perimeter zones are included in full + perimeter arming, and the
house interior zones, in full arming only. So, part arming allows the user to arm the garage, perimeter arming is used to
secure the house perimeter at nights, and the full arming is used when leaving the house. Figure 3-4 illustrates this
example. In each diagram, the protected area is shaded.
Figure 3-4: Arming Modes: Garage Example
3.6.2.
Arming Keys
The Arming keys enable you to arm the system using any of the three arming methods: -- Full, Part and Perimeter.
Full / Part / Perimeter
Figure 3-5: Front Panel and Wireless LCD Keypad Arming Keys
16
iConnect
Installation Manual
3 Basic System Operation
3.6.3.
Full Arming
Full arming is designed for when the occupant vacates the premises.
To fully arm the system using the front panel keypad or Wireless LCD Keypad:
1.
Check if the system is ready to arm.
2.
Press the Full arming key on the keypad.
3.
If One-Key Arming is disabled, enter your user code.
3.6.4.
Part Arming
Part arming is designed for when the occupant intends to remain inside one part of the premises and secure another
part.
To partially arm the system using the front panel keypad or Wireless LCD Keypad:
1.
Check if the system is ready to arm.
2.
Press the Part arming key on the keypad.
3.
If One-Key Arming is disabled, enter your user code.
To partially arm the system using the hardwire LCD keypad:
1.
Check if the system is ready to arm.
2.
Press PART on the keypad.
3.
Select Part arming.
4.
If One-Key Arming is disabled, enter your user code.
3.6.5.
Perimeter Arming
Perimeter arming is designed for when the occupant intends to remain inside the premises and secure the perimeter.
To arm the system’s perimeter using the front panel keypad or Wireless LCD Keypad:
1.
Check if the system is ready to arm.
2.
Press the Perimeter arming key on the keypad.
3.
If One-Key Arming is disabled, enter your user code.
To arm the system’s perimeter using the hardwire LCD keypad:
1.
Check if the system is ready to arm.
2.
Press PART on the keypad
3.
Select Perimeter arming.
4.
If One-Key Arming is disabled, enter your user code.
3.6.6.
Combination Arming
The system allows you to activate a combination of two arming methods. If you Perimeter arm the system, you may
also activate Full or Part arming. Likewise, you can Perimeter arm the system after activating Full or Part arming. It is
not important which arming mode you choose first.
You can activate the second arming mode only during the exit delay of the first arming
mode. When the first exit delay expires, you cannot activate a second arming mode.
For combination arming, perform the following procedure:
1.
Check if the system is ready to arm.
2.
Activate the first arming mode.
3.
If One-Key Arming is disabled, enter your user code.
4.
While the exit delay of the first arming mode is counting down, activate the second arming mode.
5.
If One-Key Arming is disabled, enter your user code.
It is not possible to activate Full and Part arming modes simultaneously. It is necessary to
disarm first when changing from one arming mode to another arming mode.
iConnect
Installation Manual
17
3 Basic System Operation
The exit delays of the two arming modes are entirely independent. The moment an arming mode is activated, its exit
delay begins to count down. The entry delay depends on which detector was tripped first. For example, if the detector
is included in Full arming, the entry delay for Full arming counts down – see p. 37, 7.3.2 Arm Set. If the detector is
included in both activated arming modes, the entry delay for Perimeter arming counts down.
If, due to open zones, the system is not ready to activate the second arming mode then both
arming methods are canceled. In this case, check that the relevant entrances are secured and
start the entire arming sequence again.
Disarming cancels both active arming modes.
3.6.7.
Disarming
When an entry/exit detector is tripped, the entry delay counts down; each arming method has its own entry delay.
To disarm the system:
Enter a valid user code, the system is disarmed.
You can only disarm all the active arming modes.
3.7.
Additional Arming Options
3.7.1.
Forced Arming
Forced arming enables you to arm the system when the system is not ready. For example, if a door protected by a
magnetic contact is open, you may arm the system on condition that the door will be closed by the end of the Exit delay.
If the door is still open after the exit delay expires, an alarm is generated.
Two conditions enable you to perform Forced arming:
• Forced arming is enabled – see p. 46, 9.3.1 Forced Arm.
• The detector that is causing the System Not Ready condition is Force Arm enabled – see p. 38, 7.3.6 Force
Arm.
3.7.2.
Instant Arming
Instant arming is a feature that allows you to cancel the entry delay after Part or Perimeter arming the system. For this
feature to function, it must be enabled in programming – see p. 47, 9.3.4 Instant Arming.
To instantly arm the system.
1.
Check if the system is ready to arm.
2.
Press the Part or Perimeter arming key on the keypad and enter your user code if One-Key Arming is disabled.
3.
Press and hold down on your keypad until the message Instant Arming, OK? is displayed
4.
Press '√ʹ; the entry delay for the current arming period is canceled.
3.7.3.
Disarming
When an entry/exit detector is tripped, the entry delay counts down; each arming method has its own entry delay.
To disarm the system:
Enter a valid user code, the system is disarmed.
3.7.4.
Remote Arming/Disarming via SMS
You can arm and disarm the system remotely by sending the SMS commands from a cellular phone to the Cellular
Communication Module (GPRS or Ethernet). Additionally, you can check the arm status of the system by sending an
Arm Status request message.
Each SMS command contains the following elements:
SMS Command Descriptor (up to 43 characters of free text)
# (delimiter – separates the descriptor from the actual command)
User Code (4 digits)
Command (120=Disarm, 121=Full Arm, 122=Part Arm, 123=Perimeter Arm, 124=Full + Perimeter Arm, 125=Part
+ Perimeter Arm, 200=Arm Status)
The following example shows the format of an SMS command for arming the system:
18
iConnect
Installation Manual
3 Basic System Operation
F U L L
A R M # 1 2 3 4 1 2 1
While the SMS Command Descriptor is optional, you must start the SMS command with the
# symbol for the system to accept the command.
After an SMS command is executed by the system, you can program the system to return a confirmation message to the
sender – see p. 62, 10.7.5 SMS Confirmation.
3.7.5.
Arm Status Reply
On receiving an Arm Status request message, the system returns a status message to the sender. This message includes
the system status and the descriptor of the user or the device used to arm/disarm the system.
The following example shows an Arm Status Reply message reporting that the system was fully armed by Master User.
F UL L
3.7.6.
A R ME D - MA S T E R
US E R
Remote Arming/Disarming via DTMF
Using the Telecontrol feature, you can arm and disarm the system via the telephone with DTMF commands. For further
information on the Telecontrol features, see p. 30, 5.1.5 Arm/Disarm DTMF Commands.
3.7.7.
Remote Arming/Disarming via WUAPP
You can arm and disarm the system remotely using the WUAPP (Web User Application) – see p. 124, Arm/Disarm.
3.7.8.
Alarm Activation
In the event of an emergency, the user can generate three kinds of alarms from the front panel keypad, wireless keypad
or keyfobs.
To activate a SOS Panic alarm from the
Keyfob (EL-4714):
• Press B1 and B2 buttons
simultaneously.
Figure 3-6: SOS Panic Alarm Activation (EL-4714)
To activate an SOS Panic alarm from the
front panel keypad and the Wireless LCD
Keypad:
• Press and hold down the SOS
buttons simultaneously.
Figure 3-7: SOS Alarm Activation (Front Panel
Keypad/Wireless LCD Keypad)
To activate a Fire alarm from the front
panel keypad or hardwire LCD keypad:
• Press and hold down buttons
1 and 3 simultaneously.
Figure 3-8: Fire Alarm Activation
To activate a Medical alarm from the front
panel keypad or hardwire LCD keypad:
• Press and hold down buttons
4 and 6 simultaneously.
Figure 3-9: Medical Alarm Activation
iConnect
Installation Manual
19
4 Advanced System Operation
4.
Advanced System Operation
Besides the basic arming functions described in the previous chapter, you can access additional functions via the menu.
This chapter describes these functions and the menu navigation procedure.
4.1.
Menu Navigation
Alphanumeric
Keypad
Menu
Navigation
Keys
HA Off Key
HA On Key
Service Call Key
Figure 4-1: On-board Keypad Layout
The Front Panel/LCD keypads' friendly, menu-driven interface is designed to facilitate operation and provide a gentler
learning curve for first-time users. You can navigate through the menus using the arrow navigation keys (/) and
make simple yes/no decisions using the '√ʹand Χ keys.
For example, perform the following procedure to navigate to Service, Interface Test.
1.
Press '√ʹ to enter Menu mode.
2.
Enter an authorized user code; the first menu item, 1. Cancel Report, is displayed.
3.
Press until 7. Service is displayed.
4.
Press '√ʹ to enter the Service menu.
5.
Press until 3. Test is displayed.
6.
Press '√ʹ to choose the displayed function.
Press the 'Χ' key to return to the previous menu level. Press this key when you are in the
main menu to exit Menu mode.
As an alternative to scrolling through menu options, you may enter a function’s shortcut once you have entered Menu
mode. Shortcut numbers appear in square brackets in the procedures throughout this manual.
4.1.1.
Menu Mode Timeout
Menu mode automatically terminates a certain amount of time after the last keystroke. The duration of this timeout
depends upon which code is used to enter the menu. Usually the Menu Mode Timeout is two minutes but if you enter
menu mode using the Installer code, the timeout is extended to fifteen minutes.
4.2.
Cancel Report
This feature allows the user to cancel false alarms. Cancel Report behavior depends on time when it is performed. If the
user selects Cancel Report:
• …before the alarm/restore message is sent, all the pending alarm or restore messages in the queue are
aborted and marked "Cancelled" in the event log.
• …within 5 minutes since an alarm, a Cancel Report event and the user number are sent to the Central
Station;
• …at the moment when the event is being reported (communication in progress), the event reporting is not
cancelled;
Non-alarm events (system trouble, arm/disarm etc.) are not aborted by Cancel Report.
20
iConnect
Installation Manual
4 Advanced System Operation
To activate cancel report:
• From the main menu, select Cancel Report. [1].
4.3.
Zone Bypassing/Unbypassing
When a detector is bypassed, it is ignored by the system and does not generate an alarm when triggered.
To bypass or unbypass a detector:
1.
From the Bypass Zones menu, select Bypass/Unbyp. [21].
2.
Using the arrow keys, scroll to the detector you want to bypass or unbypass.
3.
Press '√ʹ to change the bypass status.
4.
Press Χ; Save Changes? is displayed.
5.
Press '√ʹ to confirm the changed bypass status.
To unbypass all detectors.
1.
From the Bypass Zones menu, select Unbypass All [22].
2.
Press '√ʹ; all detectors are unbypassed.
All bypassed zones are automatically unbypassed when the system is disarmed.
A Fire zone cannot be bypassed.
4.4.
User Codes
The Control System supports up to 32 individual user codes. Each of these codes is four digits long. Most system
operations require you to enter a valid user code. The ability to perform an operation is defined by your user code’s
authorization level. These authorization levels are pre-defined for each code as explained below.
Codes 1-29 can be edited only by the Master code.
The Installer code, Guard Code and the Central Station TWA Code can be
edited only by the installer.
Code 1: Master Code
The Master code is the highest user authorization level. With the Master code, you can edit all other user codes except
the Installer code, the Guard code and the Central Station TWA Code. Additionally, the Master code grants access to
the Event Log, the Service menu and Home Automation Schedule programming. The Master code is a "controlled"
code. Arming and disarming using this code causes the Control System to notify the central station with an
Arm/Disarm event message*.
The default Master code is 1234. Change this code immediately after installing
the system!
Codes 2-19: Controlled Codes*
When you use a controlled user code for arming and disarming, the Control System notifies the central station with an
Arm/Disarm event message.
Codes 20-25: Non-controlled Codes
Non-controlled codes do not cause the Control System to send Arm/Disarm event messages to the central station. The
Control System sends a Disarm message only if you use this code to disarm the system after an alarm occurrence.
Codes 26-27: Limited Codes
A Limited code enables the user to issue a code that is valid for one day only. This code automatically expires 24 hours
after it has been programmed. These codes are "controlled" in that their use for Arm/Disarm is notified to the central
station.
Code 28: Duress Code
The Duress code is designed for situations where the user is being forced to operate the system. This user code grants
access to the selected operation, while sending a Duress event message to the central station.
*
Only if arm/disarm reporting is enabled during System Programming
iConnect
Installation Manual
21
4 Advanced System Operation
Code 29: Telecontrol Code
The Telecontrol code is designed to enable the user to perform a number of tasks via their telephone using DTMF
commands. Using this code, the user can call their system to arm and disarm, turn on and off Home automation units,
activate and deactivate the PGM output, cancel siren activation or establish Two-Way Audio communication.
Code 30: Central Station TWA Code
The Central Station TWA code is designed to enable the central station operator to establish Two-Way Audio
communication with the Control System after an alarm. This code is valid for use for the first ten minutes after an alarm
has occurred. This code can only be used for this specific purpose and does not grant access to any additional system
functions such as disarming.
Code 31: Guard Code
Guard Code is an option that allows a security guard to check the premises in case of an alarm.
Code 32: Installer Code
The Installer code grants access to the Programming menu and the Service menu. Additionally, this code enables you to
view and clear the Event Log.
The default Installer code is 1111. Change this code immediately after installing the
system!
4.4.1.
Editing User Codes
To edit a user code:
1.
From the main menu, select User Codes [4].
2.
Select the code you want to edit.
3.
From the code’s sub-menu, select Edit Code [#1]; the 4-digit code is displayed with the cursor flashing on the first
digit.
4.
Edit the code.
5.
Press '√ʹ; the new code is stored in the memory.
If you enter a code that is identical to an existing user code, the Control System sounds
an error tone and the new code is not accepted.
4.4.2.
Deleting User Codes
To delete a user code:
1.
From the main menu select, User Codes [4].
2.
Select the code you want to delete.
3.
From the code’s sub-menu, select Edit Code [#1]; the 4-digit code is displayed with the cursor flashing on the first
digit.
4.
Enter 0000.
5.
Press '√ʹ; the code is deleted.
The Installer and Master codes cannot
be deleted.
4.4.3.
User Code Descriptors
Each user code can be assigned a 16-character descriptor. These descriptors help to identify users in the event log and in
SMS Follow-Me messages.
To edit a code descriptor:
1.
From the main menu, select User Codes [4].
2.
Select a code.
3.
From the code’s sub-menu, select Descriptor [#2].
4.
Edit the descriptor using the alphanumeric keypad.
5.
Press '√ʹ when you have finished editing.
22
iConnect
Installation Manual
4 Advanced System Operation
4.5.
Follow-Me
The Follow-Me feature is designed to notify the user that certain events have occurred. The events that are sent to the
Follow-Me telephone number are those events that the user is authorized to view in the event log; events that can be
viewed only by the installer are not sent to the Follow-Me number – see p. 130, Appendix D: Event Table. If using the
TWA Follow-Me feature, the audio channel is opened after alarm events only.
To edit the Follow-Me number:
1.
From the main menu, select Telephone, Follow-me Number # [51].
2.
Enter a telephone number for Follow-Me communication. If using the SMS Follow-Me feature, this number must
be for a cellular phone with the capability to receive SMS messages.
You may only access Follow-Me programming if the protocol for Account 3 is programmed
as SMS or TWA Follow-Me.
4.6.
Event Log
The event log records the last 1022 events the system has undergone. The log uses the FIFO (First In, First Out) method,
automatically erasing the oldest event when the log is full.
To view the event log:
1.
From the Event Log menu, select View Log [61]; a summarized version of the most recent event is displayed.
2.
Use the arrow keys to scroll through the events.
3.
When you have finished viewing, press Χ to exit the log.
Press the
key to view the time/date stamp or the device/user number on the second row of the display.
The event log displays the following information for each event:
• The event descriptor – a brief description of the event that occurred.
• The zone where the event occurred.
• Time/date stamp – the exact time the event occurred.
• Report details – a single character indicating whether the event was reported to the central station. The
options available are R: Report Sent, F: Report Failed, C: Report Canceled or N: No Report.
Figure 4-2 shows the detailed event log entry for a Fire alarm on November 14th 2008. The event was successfully
reported to the central station.
Figure 4-2: Detailed Event Log Display
4.6.1.
Event Log Authorization Levels
Every event that occurs is recorded in the event log. However, certain events are intended for the installer only. Those
events include various service messages that are of little interest to the regular user. The View Log function requires
you to enter either the Master or Installer code. The events that are displayed depend on which code you use to enter
the log – see p.130, Appendix D: Event Table.
4.6.2.
Clearing the Event Log
The Clear Log function erases all events from the log. After performing this function, a Clear Log event is recorded in
the log. The Clear Log function is accessible using the Installer code only.
To clear the event log:
1.
From the Event Log menu, select Clear Log [62]; the OK? confirmation message is displayed.
2.
Press '√ʹ; the log is cleared -- See p.130, Appendix D: Event Table.
iConnect
Installation Manual
23
4 Advanced System Operation
For certain versions of the iConnect
be disabled.
4.7.
Control System software, the Clear Log function may
Service Menu
The Service menu is accessible using either the Installer or Master code. This menu includes various functions that
enable you to test the system effectively.
4.7.1.
Set Time & Date
The time and date are used to time stamp events in the event log. Additionally the time is also displayed on the LCD
display.
To set the time:
1.
From the Service menu, select Set Time/Date, Set Time [7011].
2.
Enter the current time.
3.
Press '√ʹ; the time is modified.
To set the date:
1.
From the Service menu, select Set Time/Date, Set Date [7012].
2.
Enter the current date.
3.
Press '√ʹ; the date is modified.
The format of the time and date is defined in the System Options – see p.48, 9.6.3 Time/Date
Format. If you are setting the time in 12hr format, use the key to toggle between AM and
PM.
4.7.2.
Message Center
The iConnect
Control System Message Center is designed to allow the user to record a short message that may be
played back later by another user. After a message is recorded, Message Waiting is displayed on the LCD until the
message is played back. If the Vocal Message option is enabled, the Message Waiting vocal message is sounded.
Recording a new message automatically overwrites all the previous messages in the
Message Center.
To play back a recorded message:
• From the Service menu, select Messages, Play Message [7021].
To record a message:
1.
From the Service menu, select Messages, Record Message [7022].
2.
Press '√ʹ to start recording the message.
3.
Record your message. The message may be up to twenty seconds long.
4.
Press '√ʹ to stop recording; the message is automatically played back and OK? Is displayed.
5.
Press '√ʹ to save your recording.
Time left out of the 20 seconds' timeout is displayed on the LCD.
The Record and Play options can also be accessed via a convenient shortcut without needing to enter a valid user code.
To play back a recorded message via a keypad shortcut:
From Standby mode, press then '√ʹ.
To record a message via a keypad shortcut:
From Standby mode, press Χ then √. On the keypad, both LEDs flash in tandem during recording.
4.7.3.
Wireless Siren Test
To test the wireless siren:
From the Service menu, select WL Siren Test [7031]; the external siren is sounded briefly.
24
iConnect
Installation Manual
4 Advanced System Operation
4.7.4.
Siren Test
To test the Control System’s built-in siren:
From the Service menu, select Siren Test [7032]; the Control System’s built-in siren is sounded briefly.
4.7.5.
Interface Test
The Interface test enables you to check if the speaker, LEDs and LCD are functioning correctly.
To test the system interface:
From the Service menu, select Interface Test [7033]; a short sequence of chimes are sounded from the speaker, all LEDs
flash and the LCD is tested on all connected LCD keypads.
4.7.6.
Walk Test
To initiate Walk Test mode:
1.
From the Service menu, select Walk Test [7034]; a list of registered detectors appears.
2.
Trigger each detector; when the system receives a successful transmission from a detector, the detector is
removed from the list.
3.
When all the detectors are removed from the list, End Walk Test is displayed.
4.
Press Χ to exit Walk Test mode.
4.7.7.
Snapshot Test
The Snapshot Test enables you to check if the video verification detector cameras are functioning correctly
To test the video verification detector cameras:
1.
From the Service menu, select Test and then Snapshot Test [7035]; a list of registered detectors appears.
2.
Select a detector from the list and press √; a snapshot of the monitored area in taken and the results can be viewed
in the Web User Application.
3.
Repeat the test for each installed detector.
4.
Press Χ to exit Snapshot Test mode.
4.7.8.
Transmitters
The Transmitters menu offers a number of utilities that serve as a valuable aid during installation.
TX List
The TX List is a scrollable inventory of all registered transmitters and their last reported status.
To view the TX list:
1.
From the Service menu, select Transmitters, TX List [7041]; the first transmitter on the list is displayed.
2.
Using the arrow buttons, scroll through the transmitter list.
3.
When you have finished viewing, press Χ to exit the list.
The TX list displays the following information for each transmitter:
• The zone/device number or descriptor. Press the
key to toggle the display.
• The signal strength of the last received transmission.
• An abbreviation indicating the last received status of the transmitter – see Table 4-1.
Table 4-1: Transmitter Status Abbreviations
Item…
OK
TA
BT
OS
NA
iConnect
Description…
The transmitter is functioning correctly
Tamper condition
Battery low
The transmitter is out of synchronization
The transmitter is inactive – see p. 36, 7.2.3 Supervision Time
Installation Manual
25
4 Advanced System Operation
Figure 4-3: TX List Display
In most cases, an "out of synchronization" condition indicates that an unauthorized attempt
at grabbing the transmission has occurred – i.e. a previous transmission has been recorded
and sent by somebody trying to violate the system.
TX Test
TX Test enables you to identify transmitters and test their signal strength. In TX Test mode, each time a transmission is
received, the activated transmitter is displayed. If you enter this function using the Master code, a chime is sounded
every time a transmission is received. If you enter this function using the Installer code, a sequence of tones in
combination with subsequent LED flashes indicate the transmitter’s signal strength – see Table 4-2.
This feature helps you to determine the best location to install a transmitter.
The lowest recommended signal strength for any installed transmitter is 2. If the received
signal strength is lower than 2, relocate the transmitter.
Table 4-2: Signal Strength Tones
Signal Strength
1
2
3
4
Tones
1 Tone
2 Tones
3 Tones
4 Tones
LED Flash
1
2
3
4
To initiate TX Test mode:
1.
From the Service menu, select Transmitters, TX Test [7042].
2.
Activate a transmitter; the transmitter’s details are displayed.
3.
When you have finished, press Χ to exit TX Test mode.
RF Link Test
RF Link Test enables you to measure the RF noise levels between a selected transmitter and the system’s receiver.
To view RF Link level reading:
1.
From the Service menu, select RF Link Test [7043]; the first transmitter on the list is displayed.
2.
Using the arrow buttons, scroll through the list and select a transmitter.
3.
Press '√ʹ and activate the selected transmier, e.g. press keyfob buon. The RF noise levels of the selected
transmitter and the system's receiver are displayed.
4.
When you have finished, press Χ to exit RF Link Test mode.
Environmental RSSI
Environmental RSSI Test enables you to measure the RF noise level of the systems environment. The Control System
will start measuring the RSSI level every second, and it will display the result on the LCD.
RSSI level can jump momentarily when a detector is activated. It doesn’t mean that the
receiver is noisy.
To view the Environment RSSI level reading:
1.
From the Service menu, select ENV. RSSI [7044]; the RF noise of the system's environment is displayed.
2.
When you have finished, press Χ to exit the Environmental RSSI Test mode.
26
iConnect
Installation Manual
4 Advanced System Operation
4.7.9.
Audio Volume
To adjust the sensitivity of the microphone and the volume of the speaker:
1.
Establish a two-way audio connection – see 5.1.4 Telecontrol Call Procedure.
2.
From the Service menu, select Audio Volume [705].
3.
Using the arrow keys on the Front Panel keypad, adjust the setting according to the following table.
Table 4-3: Voice Level Adjustment
Key…
1
4
3
6
4.
Function
Increases microphone sensitivity
Reduces microphone sensitivity
Increases speaker volume
Reduces speaker volume
Press '√ʹ; the new seings are stored in the memory.
4.7.10. GSM Signal Strength
You can measure the GSM signal strength. This function enables you to calculate the optimal location to install the
Control System with the Cellular Communication Module.
To view the GSM signal strength reading:
• From the Service menu, select GSM Signal [706]; the signal strength of the cellular network is displayed.
Table 4-4: GSM Signal Level
Reading
8-9
5-7
Less than 5
Meaning
Reception is good
Reception is acceptable
Reception is unacceptable
In severe cases of low GSM signal consider using external GSM antenna.
4.7.11. Display Version
To display the system’s software and hardware versions:
From the Service menu, select Version [707]; the hardware (HW) and software (SW) versions are displayed.
4.7.12. Enable Programming
The Enable Programming command enables a user with Master code authorization to grant access to system
programming. This feature is relevant only if the Installer Access and/or the RP Access options are programmed as
"User Initiated" – see p. 52, 9.14 Installer Access and p. 59, RP Access Options.
To grant access to the installer or Remote Programmer:
From the Service menu, select Enable Prog. [708]; a 30-minute time window is opened during which the Installer Code
is valid or RP communication may be established.
4.7.13. Global Chime
The Chime feature causes the Control System’s built-in siren to ring when specific zones are triggered. Using the Global
Chime option, you can enable or disable this feature for all zones that are defined as Chime enabled – see p.38, 7.3.5
Chime.
To enable or disable Global Chime:
1.
From the Service menu, select Global Chime [709].
2.
Select either Enabled or Disabled.
3.
Press '√ʹ when the desired setting is displayed.
Though the Service menu is accessible to the Master and Installer only, Global Chime can
also be accessed via a convenient shortcut without needing to enter a valid user code. To
access the Global Chime option from Standby mode, press then.
iConnect
Installation Manual
27
4 Advanced System Operation
4.7.14. Remote Firmware Update
The Remote Firmware Update command enables a user with Master code authorization to initiate the update. This
feature is relevant only if the Remote Firmware Update mode is programmed as "User Initiated" – see p. 63, 10.8.4
Remote Firmware Update
To initiate Remote Firmware Update:
From the Service menu, select, SW Update [710]; a 24-hours time window is opened during which the Remote
Firmware Update may be performed.
4.7.15. IP Display
When using Ethernet connection, you can view the LAN IP address of the Control System, i.e. the address that your
home router has assigned to the Control System.
To display the IP Address:
From the Service menu, select IP Display [711]; the LAN IP address of the Control System is displayed.
28
iConnect
Installation Manual
5 Telecontrol and Two-Way Audio
5.
Telecontrol and Two-Way Audio
The iConnect
Control System offers a range of Telecontrol features that provide remote access via the telephone.
These features include Two-Way Audio, remote arming/disarming and cancel siren activation. This chapter explains
these features and their operating procedures.
Telecontrol features can be separated into two fundamental groups; incoming and outgoing calls. These groups differ in
their associated features.
5.1.
Incoming Calls
The Control System can receive incoming calls from either the user or central station operator. Users may use this
feature as a convenient way of contacting their family, operating their system or to check their home when they are
away. Additionally, the monitoring service can contact the user in the event of an emergency or use this feature for
listen-in alarm verification.
For any of the incoming Telecontrol features to function, Telecontrol must be enabled in the Communication Options
section of the Programming menu – see p. 61, 10.6.8 Incoming Calls.
5.1.1.
User Code Verification
To prevent unauthorized attempts to connect with the Control System, there are two user codes designed for use with
the Telecontrol features. The Telecontrol code enables the user to establish communication with the Control System at
any time. Additionally, the Central Station TWA Code is used exclusively for Two-Way Audio alarm verification and is
only valid for a ten-minute period following an alarm – see p. 21, 4.4 User Codes.
5.1.2.
Incoming Calls via PSTN
In the case of PSTN communication, the Control System often shares a line with regular telephone handsets, an
answering machine or a fax machine. It is therefore important that the Control System distinguish between calls so that
Control System employs a double call
it knows when to pick up the relevant call. For this purpose the iConnect
method.
To connect to the Control System using the double call method:
1.
Dial the telephone number of the line connected to the Control System.
2.
Wait for two or three rings and hang-up.
3.
Wait at least five seconds and dial the number again; on the second ring, the Control System picks up and sounds
two DTMF tones.
5.1.3.
Incoming Calls via a Cellular Network
The Cellular Communication module has its own individual telephone number and therefore, the double call method is
not needed. In this case, the user or central station operator may call the Control System directly.
5.1.4.
Telecontrol Call Procedure
The following procedure explains how to make a Telecontrol call. The conditions and procedure differ when using
PSTN or Cellular Communication. For further information, see the entire section 5.1 Incoming Calls.
To make a Telecontrol call:
1.
Call the Control System either using the double call method (PSTN) or directly (Cellular/PSTN); when the
Control System picks up, two DTMF tones are sounded.
2.
Enter the Telecontrol code (Code 29) on your telephone within 15 seconds.
Do not enter your user code until you hear the two DTMF tones. Any digits entered before
the tones are sounded are disregarded by the system.
3.
A DTMF tone is sounded to indicate that the system is ready to receive commands.
The following DTMF commands are available:
o
Press "2" for Two-Way Audio.
If the TWA mode is defined as "Simplex" (see p. 61, 10.6.11, TWA Mode.), the audio channel opens in
Listen mode (microphone active/speaker mute). To switch to Speak mode, press "1" on your telephone.
To switch back to Listen mode, press "0" on your telephone.
iConnect
Installation Manual
29
5 Telecontrol and Two-Way Audio
During the TWA session, you can adjust the speaker volume using the arrow buttons.
o
o
o
o
o
o
o
Press "3" to fully arm the system.
Press "4XX" to turn HA unit #XX ON.
Press "430" to activate PGM output (Unit 30/31)
Press "5XX" to turn HA unit #XX OFF.
Press "530" to deactivate PGM output (Unit 30/31)
Press "6" to disarm the system.
Press "9" to cancel the siren.
The Arm/Disarm, Home Automation, PGM on/off, and Siren canceling can also be executed
at any time during a Two-Way Audio session.
Error beeps (three tones) sound in case of a wrong command.
To clear the last command, press "" or "#".
o
4.
The duration of the call is determined by the TC/VM Timeout -- see p. 61, 10.6.9 Telecontrol/Vocal
Message Timeout. Ten seconds before the timeout expires, two short DTMF tones are sounded. To
extend the call, press "7" on your telephone. This command restarts the timeout.
To disconnect before the end of the timeout, press "" then "#" on your telephone.
5.1.5.
Arm/Disarm DTMF Commands
During a Telecontrol call, you can arm and disarm the system remotely using the DTMF commands (see above). When
arming the system in this way, the system is armed immediately without an exit delay.
5.1.6.
HA and PGM DTMF commands
During a Telecontrol call, you can turn On and Off the Home Automation units using the DTMF commands "4XX" (HA
unit #XX On) and "5XX" (HA unit #XX Off). PGM unit is defined as HA Unit 30. You can activate and deactivate PGM
using the DTMF commands "430" (PGM On) and "530" (PGM Off).
5.1.7.
Siren Cancel ("Bell Cancel")
The siren is muted during Two-Way Audio communication. At the end of the call, the siren is re-activated (if the Siren
Cut-Off has not yet expired). During the call, pressing "9" on your telephone cancels the re-activation of the siren.
5.1.8.
Central Station Two-Way Audio
Central Station Two-Way Audio is an alarm verification feature that enables the central station operator to establish
Two-Way Audio communication with the Control System within ten minutes of an alarm.
To make a Central Station TWA call:
1.
Call the Control System either using the double call method (PSTN) or directly (Cellular); when the Control
System picks up, two DTMF tones are sounded.
2.
Enter the Central Station TWA code (Code 30) on your telephone within 15 seconds.
Do not enter your user code until you hear the two DTMF tones. Any digits entered before
the tones are sounded are disregarded by the system.
3.
If the TWA mode is defined as "Simplex" (see p. 61, 10.6.11 TWA Mode), the audio channel opens in Listen mode
(microphone active/speaker mute). To switch to Speak mode, press "1" on your telephone. To switch back to
Listen mode, press "0" on your telephone.
4.
The duration of the call is determined by the TC/VM Timeout -- see p. 61, 10.6.9 Telecontrol/Vocal Message
Timeout. Ten seconds before the timeout expires, two short DTMF tones are sounded. To extend the call,
press "7" on your telephone. This command restarts the timeout.
5.
To disconnect before the end of the timeout, press "" then "#" on your telephone.
30
iConnect
Installation Manual
5 Telecontrol and Two-Way Audio
5.2.
Outgoing Calls
The iConnect
Control System can make Two-Way Audio calls to the user or central station in the event of an alarm.
This feature is designed for medical, panic alarms, and for alarm verification.
5.2.1.
Service Call
The Service Call feature enables the user to establish a two-way audio connection with the central station operator. For
further information on how to program this feature, see p. 59, 10.5 Service Call.
To initiate a Service Call:
Press and hold down the Service Call key
for a few seconds.
The Control System starts to dial.
If the TWA mode is defined as "Simplex" (see p. 60, 10.6.11 TWA Mode), the audio channel opens in Listen mode
(microphone active/speaker mute). The operator may switch to Speak mode, by pressing "1" on their telephone.
Pressing "0" switches back to Listen mode.
5.2.2.
TWA Alarm Reporting
In the event of Burglary, Fire and Medical alarms, the Control System is able to report the events and then stay on the
line after acknowledgment is received (ACK 2). This allows the operator to verify the alarm or provide assistance in the
event of an emergency.
For this feature to function, you must enable Two-Way Audio for both the account and the event group.
The sequence for Two-Way Audio during alarm reporting is as follows:
1.
An alarm event is sent to the central station and acknowledgment is received (ACK 2).
2.
If Two-Way Audio is enabled for the account and event group, the Control System stays on the line and opens
the audio channel.
3.
If the TWA mode is defined as "Simplex" (see p. 61, 10.6.11 TWA Mode), the audio channel opens in Listen mode
(microphone active/speaker mute). The operator may switch to Speak mode, by pressing "1" on their
telephone. Pressing "0" switches back to Listen mode.
4.
The duration of the call is determined by the TC/VM Timeout. Ten seconds before the timeout expires, two short
DTMF tones are sounded. To extend the call, the operator presses "7" on their telephone. This command
restarts the timeout.
5.
To disconnect before the end of the timeout, the operator presses "" then "#" on their telephone.
If multiple events are sent, the Control System sends all the events before opening the audio channel.
When using the SIA protocol for event reporting, this feature functions in "listen-in" mode
only.
5.2.3.
Two-Way Audio after Vocal Messages
If Two-Way Audio is enabled for a Vocal Message account, the user can open the audio channel by pressing "2" on their
telephone after the system has played all of the event messages.
The sequence for Two-Way Audio after a vocal message is as follows:
1.
An event occurs and the Control System calls the telephone number of the first Voice Report Account chosen.
2.
When the user answers the call, the Home ID message and the relevant event message are played.
3.
If Two-Way Audio is enabled for the Voice Report account, the user presses "2" on their telephone to open the
audio channel.
4.
The duration of the call is determined by the TC/VM Timeout. Ten seconds before the timeout expires, two short
DTMF tones are sounded. To extend the call, the user presses "7" on their telephone. This command restarts
the timeout.
5.
To disconnect before the end of the timeout, the user presses "" then "#" on their telephone.
iConnect
Installation Manual
31
5 Telecontrol and Two-Way Audio
5.2.4.
TWA Follow-Me
The TWA Follow-Me feature is designed to establish a Two-Way Audio connection with the user in the event of an
alarm. For this feature to function, the account’s protocol must be defined as TWA Follow-Me.
The sequence for a Two-Way Audio Follow-Me call is as follows:
1.
An alarm occurs.
2.
The Control System dials the programmed telephone number and sounds two DTMF tones when you pick up the
call.
3.
Press "2" on your telephone; the Control System opens the audio channel.
If you press "9" to answer the call, the Control System simultaneously cancels the siren when
opening the audio channel.
4.
If the TWA mode is defined as "Simplex", (see p. 60, 10.6.11 TWA Mode), the audio channel opens in Listen mode
(microphone active/speaker mute). To switch to Speak mode, press "1" on your telephone. To switch back to
Listen mode, press "0" on your telephone.
5.
The duration of the call is determined by the TC/VM Timeout. Ten seconds before the timeout expires, two short
DTMF tones are sounded. To extend the call, press "7" on your telephone. This command restarts the
timeout.
6.
To disconnect before the end of the timeout, press "" then "#" on your telephone.
32
iConnect
Installation Manual
6 Home Automation and PGM Control
6.
Home Automation and PGM Control
The purpose of this chapter is to explain the various methods used to control X10 Home Automation (HA) units
installed around the home and PGM output. The PGM is a programmable output that is triggered according to specific
system status conditions, or by remote command sent via PSTN, GSM, Ethernet, keyfob, keypad, or RP as explained
below. For further information on the X10 protocol and the choice of options that are available in programming, see p.
70, 12 Home Automation Programming.
6.1.
Keypad Control
Using the front panel keypad or the Wireless LCD Keypad, you can control HA units and PGM output with the
dedicated Home Automation keys – see Figure 6-1.
On
Off
Figure 6-1: Home Automation Keys (Front Panel keypad or Wireless LCD Keypad)
To control HA units or PGM output via the front panel keypad or the Wireless LCD Keypad:
1.
Press one of the two Home Automation keys on the keypad (On or Off).
2.
Enter the number of the required HA unit in two-digits (01-16, or 30, 31 for PGM output); the command is sent to
the HA unit or PGM.
To control HA units via the menu on the keypad (not relevant to PGM):
1.
From the main menu, select Home Automat. [3]; HA Unit #1 is displayed.
2.
Use the arrow keys to scroll to the unit you want to control.
3.
Press '√ʹ to select the HA unit.
4.
Use the arrow keys to toggle the ON/OFF command.
5.
Press '√ʹ to select the command.
6.
Scroll to the next unit you want to control or press Χ to exit this feature.
6.2.
Keyfob Control
You can control up to two different HA units or PGM using any of the four button keyfobs registered to the system. For
further information on how to assign keyfob buttons to HA units or PGM, see p. 40, 7.4.2 Keyfob Button Assignment.
6.3.
Telephone Control
You can send On and Off commands to HA units or PGM output using SMS messages sent from a cellular phone to the
Cellular Communication module. Alternatively, the HA unit or PGM can be controlled by using DTMF commands
during Telecontrol call (either to the cellular or PSTN communication modules). For this feature to function correctly,
Telephone control must be enabled for the specific HA units you want to control (see p. 71, 12.2.6 Telephone Control),
and/or for PGM respectively – see p. 49, 9.7.1 Output Trigger.
6.3.1.
DTMF command
Using the Telecontrol feature, you can turn on and off the HA units and PGM output via the telephone with DTMF
commands. For further information on the Telecontrol features, see p. 29, 5 Telecontrol and Two-Way Audio and p. 30,
5.1.6 HA and PGM DTMF commands.
6.3.2.
SMS Command Format
Each SMS command contains the following elements:
iConnect
SMS Command Descriptor (up to 43 characters of free
text)
# (delimiter – separates the descriptor from the actual
command)
User Code (4 digits)
Installation Manual
Command (0=Off, 1=On)
Device Number (HA Units: 01-16, or 30, 31 for PGM output)
33
6 Home Automation and PGM Control
The following example shows the format of an SMS command to switch on a water boiler controlled by HA unit 8.
B O I
L E R
O N # 1 2 3 4 1 0 8
While the SMS Command Descriptor is optional, you must start the SMS command with the
# symbol for the system to accept the command.
6.3.3.
SMS Confirmation Message Format
After an SMS command is executed, the system can return a confirmation SMS message to the sender. This message
includes the descriptor of the HA unit or PGM descriptor and the command that was sent. For further information on
how to enable this feature, see p. 62, 10.7.5 SMS Confirmation.
The following example shows the confirmation message the sender receives for the sample command from the previous
section.
B O I L E R - O N
6.4.
Scheduling (not relevant to PGM)
Scheduling allows you to program the Control System to send On/Off commands to HA units at specific times. You can
also program the days of the week that the schedule is active. Scheduling is also available in the WUAPP (Web User
Application) – see p. 129, Automation
6.4.1.
On Time
To edit an HA unit’s "On" Time:
1.
From the main menu, select HA Schedules [8].
2.
Select a HA unit.
3.
From the HA unit’s sub-menu, select On Time [1].
4.
Enter a time (HH:MM).
6.4.2.
Off Time
To edit an HA unit’s "Off" Time:
1.
From the main menu, select HA Schedules [8].
2.
Select a HA unit.
3.
From the HA unit’s sub-menu, select Off Time [2].
4.
Enter a time (HH:MM).
6.4.3.
Weekly Schedule
To program the days of the week that the schedule is active:
1.
From the main menu, select HA Schedules [8].
2.
Select a HA unit.
3.
From the HA unit’s sub-menu, select Schedule [3].
4.
Use keys 1 to 7 to toggle the days on and off.
Table 6-1: Weekly Schedule
Key
1
2
3
4
34
Value
Sunday
Monday
Tuesday
Wednesday
Key
5
6
7
Value
Thursday
Friday
Saturday
iConnect
Installation Manual
7 Devices
7.
Devices
This chapter explains how to register devices to the system and define programming options for each device. For
further information on devices, please refer to the installation instructions included with each device.
7.1.
Device Descriptors
You can assign a 16-character descriptor to each device. These descriptors help identify the devices when you operate
and program the system.
To edit a device descriptor:
1.
From the Programming menu, select Devices [91].
2.
Select a device type.
3.
From the device’s sub-menu, select Descriptor.
4.
Edit the descriptor using the alphanumeric keypad.
5.
Press '√ʹ when you have finished editing.
7.2.
Wireless Devices
7.2.1.
Registering Wireless Devices
For the system to recognize individual devices, each device must be registered to the system. For example, if the device
is a wireless transmitter, registration enables the system to identify the source of a received transmission. Each device
has an individual encrypted ID code. Registering the device to the system familiarizes the system with this code.
It is not necessary to register hardwire detectors connected to Zones 33-34.
To register a device to the system:
1.
From the Programming menu, select Devices [91].
2.
Select the type of transmitter you want to register. For example, if you want to register a wireless detector to a
zone, select Zones.
3.
Select the specific device you want to register (for example, Zone 4); the system initiates Registration mode.
During Registration mode, the system waits for two transmissions from the device.
If a device has already been registered at the selected location, the system will not initiate
Registration mode. If the device has already been registered at another location, attempts to
register it are ignored by the system. Zones 1-32 are intended for wireless detectors by
default, unless the zones 1 to 8 are programmed as wired zones connected to the Wired
Zone Module.
4.
Register the device – refer to each device’s installation instructions in Appendix B for further details.
5.
When two transmissions have been received, Save? is displayed.
6.
Press '√ʹ to confirm registration, or ‘Χ’ to cancel.
7.2.2.
Deleting and Deactivating Wireless Devices
When you want to remove a device from the system, you have to delete and deactivate the device. It is important to
delete and deactivate unused devices for two reasons. Firstly, you have to delete a device from the system before you
can register a new transmitter in its place. Secondly, if the device is a wireless detector, it is important to deactivate the
device so that the system will not react to the transmitter’s failure to send supervision signals.
To delete and deactivate a device:
1.
From the Programming menu, select Devices, [91].
2.
Select the type of wireless device you want to delete.
3.
Select the specific device you want to delete.
4.
From the device’s sub-menu, select Delete.
5.
Deactivate the device – refer to each device’s deactivation instructions in Appendix B for further details
6.
Press '√ʹ to confirm; the device is deleted from the system.
iConnect
Installation Manual
35
7 Devices
7.2.3.
Supervision Time
The detectors in Electronics Line 3000’s supervised wireless range send a supervision signal approximately 20 minutes
after its last transmission. If the system does not receive supervision signals from a specific transmitter, the transmitter
is regarded as inactive.
The amount of time after which a transmitter is considered inactive is called the Supervision Time. There is a separate
supervision time for general transmitters and devices that are registered to Fire zones.
To program the Supervision Time for general transmitters:
1.
From the Programming menu, select Devices, Superv. Time, General [9171].
2.
Enter a supervision time between 02:00 and 23:59 hours.
To program the Supervision Time for transmitters registered to Fire zones:
1.
From the Programming menu, select Devices, Superv. Time, Fire [9172].
2.
Enter a supervision time between 02:00 and 23:59 hours.
7.3.
Zones
The iConnect
Control System supports Electronics Line 3000’s supervised wireless range of transmitters that
includes various PIR detectors, magnetic contacts and smoke detectors. All these transmitters send supervision signals
to the Control System's receiver in order to indicate that the transmitter is functional.
Control System includes 33-34 security zones. Zones 1-32 are intended for wireless detectors by
The iConnect
default, unless the zones 1 to 8 are programmed as wired zones connected to the Wired Zone Module. Only one
detector can be registered to each zone.
Zone 33-34 are on-board hardwire zones. These zones are programmed in the same way as the wireless zones with the
exception of registration and deletion.
This section explains the programming exclusive to detectors. For information on registration, descriptor editing, and
deletion, see p. 35, 7.1, 7.2.1, 7.2.2. The zone menu is displayed according to the zone type (see below).
Most of the programming options are identical for hardwire and wireless zones with the following exceptions:
Wireless Zones 1-32
• Register (see: p. 35, 7.2.1 Registering Wireless Devices)
• Delete (see: p. 35, 7.2.2 Deleting and Deactivating Wireless Devices)
• Repeater (see: p. 39, 7.3.9 Repeater)
Figure 7-1: Wireless Zone Menu
Wired Zones 33-34
• Loop Type (see p. 39, 7.3.11, Loop Type (Wired zone 33-34 only)
• Loop Response (see p. 39, 7.3.12, Loop Response (hardwire zones 33-34 only)
36
iConnect
Installation Manual
7 Devices
Figure 7-2: Wired Zone Menu
7.3.1.
Zone Type
The zone type defines the type of alarm the system generates when the detector is tripped.
To program a zone type:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the detector you want to program.
3.
From the detector’s sub-menu, select Zone Type [#02].
4.
Select one of the following zone types:
•
•
•
•
•
•
•
•
Normal
Entry/Exit
Follower
Panic
Medical
Fire
24H
24Hr-X (future option)
•
•
•
•
•
•
•
Gas
Flood
Environmental
No Motion
Arm/Disarm
Crash and Smash
Not Used
For a detailed explanation on the function of each zone type, see p. 133, Appendix E: Zone Types.
7.3.2.
Arm Set
The Arm Set option allows you to define the arm methods in which the zone is included.
Each zone can be assigned to Full Arming and/or to Part and/or Perimeter Arming in any combination.
To program the Arm Set option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Arm Set [#03]; the zone’s current Arm Set setting is displayed.
Table 7-1: Arm Set Options
Arm Set
1 (F)
2 (P)
3 (PE)
4.
Description
The zone is included in Full arming.
The zone is included in Part arming.
The zone is included in Perimeter arming.
Use the keys 1, 2 and 3 to toggle the current setting.
It is not necessary to program this option for Panic, Medical, Emergency, Fire, 24Hr, Gas,
Flood and Environmental zones.
7.3.3.
Descriptor
For information on device descriptor editing, see p. 35, 7.1 Device Descriptors.
iConnect
Installation Manual
37
7 Devices
7.3.4.
Bell (Siren)
Each zone can be programmed to activate the siren when triggered or to generate a silent alarm where only a message is
sent to the central station.
To program the Bell option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Bell [#05]; the zone’s current Bell setting is displayed.
4.
Select either Enabled or Disabled.
Fire zones always activate the siren regardless of what is programmed for this option.
If the bell is disabled for Panic zones, this also disables all forms of alarm
indication from the on-board keypad in the event of a Panic alarm.
If the Bell option is enabled for Environmental or Flood zones, the system
sounds trouble tones from the keypad.
7.3.5.
Chime
When Chime is enabled, triggering the zone when the system is disarmed causes the internal siren to chime.
To program the Chime option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Chime [#06]; the zone’s current Chime setting is displayed.
4.
Select either Enabled or Disabled.
7.3.6.
Force Arm
Force arming enables you to arm the system when the system is not ready. For example, a door that is protected by a
magnetic contact is open. You may arm the system on condition that the zone is defined as Force Arm enabled. This
door must be closed by the end of the Exit delay otherwise an alarm is generated. If the magnetic contact’s zone is
defined as Force Arm disabled, the system will not be ready to arm until you close the door.
To program the Force Arm option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Force Arm [#07]; the zone’s current Force Arm setting is displayed.
4.
Select either Enabled or Disabled.
For the Force Arm feature to function, you must also enable Force Arming in System
Options -- see p. 46, 9.3.1 Forced Arm.
7.3.7.
Swinger
A zone defined as Swinger enabled can generate only a limited number of alarms during a specific time period. The
Swinger setting is defined in System Options – see p.46, 9.1 Swinger Setting.
To program the Swinger option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Swinger [#08]; the zone’s current Swinger setting is displayed.
4.
Select either Enabled or Disabled.
Do not enable the Swinger option for zones that are always active (Panic, Medical
Emergency, Fire, 24-hr, Gas, Flood and Environmental zones).
7.3.8.
CMS (Central Monitoring Station) Reporting
There is an option to enable or disable central monitoring station reporting for each burglary zone specifically. If
enabled, the alarms are reported in the ordinary way, i.e. after the wireless siren delay; if disabled, alarms from this
zone are not reported to the Central Station.
38
iConnect
Installation Manual
7 Devices
This parameter is relevant only to Burglary zones used as Normal, Entry/Exit, Follower, or
24 hours type.
To program the CMS Reporting option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select CMS Rep. [#09]; the zone’s current CMS Rep. setting is displayed.
4.
Select either Enabled or Disabled.
7.3.9.
Repeater
The repeater is an additional module that extends the range of the wireless transmitters. For a detector to use the
repeater to relay transmissions to the system, you must define the Repeater option for its zone.
To program the Repeater option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Repeater [#10]; the zone’s current Repeater setting is displayed.
4.
Select either No Repeater or Use Repeater.
Do not register the same transmitter to more than one repeater or mis-operation will
occur.
7.3.10. Sensor Parameters
For a number of 2-Way detectors (e.g. Video Verification PIR Detector EL-4755 and 4755PI) you can define specific
parameters through the control system. These parameters can be set in order to define how the device acts according to
the zone in which it has been installed
To program the sensor parameter option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Sensor Par. [#11]; the zone’s current Sensor Parameter setting is displayed.
4.
Define the parameters according to the relevant device.
5.
Press Χ, to exit the sensor parameters menu.
7.3.11. Loop Type (Wired zone 33-34 only)
This option enables you to determine the zone’s loop type.
To program the Loop Type option:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Loop [#01]; the zone’s current Loop type setting is displayed.
4.
Select either N.O., N.C. or E.O.L.R.
7.3.12. Loop Response (hardwire zones 33-34 only)
The loop response determines how long a zone needs to be opened for the control system to generate an alarm. The
following loop response options are available:
• Slow Loop (150ms) – used typically for PIR detectors, magnetic contacts, etc.
• Fast Loop (50ms) – designed for use with shock detectors
To set loop response:
1.
From the Programming menu, select Devices, Zones [911].
2.
Select the zone you want to program.
3.
From the zone’s sub-menu, select Loop Resp. [#10]; the zone’s current Loop response is displayed.
4.
Select Slow Loop or Fast Loop.
iConnect
Installation Manual
39
7 Devices
7.4.
Keyfobs
The iConnect
Control System supports two types of keyfob transmitter, EL-4711M/P and EL-4714. You can register
up to 19 keyfobs to the system. Figure 7-3 illustrates these transmitters and the functions assigned to their buttons. For
information on registration, deletion and deactivation, see p. 35, 7.2. Wireless Devices. For descriptor editing, see p. 35,
7.1 Device Descriptors.
Disarm
Full Arm
B1: Part Arm,
HA/PGM
B2: Perimeter
Arm, HA/PGM
EL-4714
Medical/Panic
Emergency
EL-4711M/P
Figure 7-3: Keyfob Button Assignments
The following sections explain the programming options exclusive to the EL-4714 keyfob transmitter. These
programming options are not relevant to the EL-4711M/P.
For panic Alarm activation with the keyfob, see p. 19, 3.7.8, Alarm Activation.
7.4.1.
Keyfob Type
You can define each registered keyfob as Controlled or Non-controlled. A Controlled keyfob causes the system to send
arm/disarm event messages to the central station. Non-controlled keyfobs never send arm messages and send a disarm
message only if the system is disarmed after an alarm occurrence.
To program a keyfob type:
1.
From the Programming menu, select Devices, Keyfobs [912].
2.
Select the keyfob you want to program.
3.
From the keyfob’s sub-menu, select Type [#2]; the current setting is displayed.
4.
Select Controlled or Non-controlled.
7.4.2.
Keyfob Button Assignment (EL-4714)
The EL-4714 includes two buttons (B1 and B2) that you can program individually.
The default functions for B1
is part arming and for B2
, perimeter arming.
Alternatively, you can program these buttons to control a specific HA unit or PGM output.
To program buttons B1 and B2:
1.
From the Programming menu, select Devices, Keyfobs [912].
2.
Select the keyfob you want to program.
3.
From the keyfob’s sub-menu, select either B1 Assign [#4] or B2 Assign [#5].
4.
Select the HA unit you want the button to control (01-16, or 30, 31 for PGM output) or enter 00 to program the
button’s default function; then press '√ʹ.
7.4.3.
SOS Panic Alarm Activation (EL-4714)
Using the four-button keyfob, you can activate an SOS Panic alarm by pressing two buttons simultaneously.
40
iConnect
Installation Manual
7 Devices
7.5.
Wireless Keypads
The system supports up to four wireless keypads, including the EL-4727 Wireless LCD Keypad. For information on
descriptor editing and deletion, see p. 35, 7.1 Device Descriptors, and p. 35, 7.2.2 Deleting and Deactivating Wireless
Devices. The EL-4727 Wireless LCD Keypad’s LED functionality is described in Appendix BError! Reference source not
found..
1. Speaker
2. LCD Display
3. Arming Keys
4. Keypad
5. Microphone (optional)
6. System Status LEDs
Figure 7-4: EL-4727 Wireless LCD Keypad
Table 7-2: EL-4727 System Status LEDs
OK LED Status
Off
On - Green
Flashing Yellow
(slowly)
Flashing Yellow (fast)
LED Status
Off
On - Green
Flashing Red
Meaning
The system is disconnected from all power sources.
The keypad is powered by AC and the battery is not low.
Local backup battery low.
Wireless LCD Keypad AC loss.
The system is disarmed.
The system is armed.
An alarm has occurred. This alarm indication is reset when
the system is armed using any of the three arming
methods.
Alarm indication is not displayed after a silent panic alarm.
For Panic Alarm activation using the Wireless LCD Keypad, see p. 19, 3.7.8 Alarm
Activation
7.6.
Repeaters
Repeaters are designed to extend the wireless range of the Control System. Up to four repeaters may be registered to
the system with a maximum of 32 transmitters associated with each receiver. Repeater is a future option that is not
available in the current firmware.
7.7.
Wireless Siren
The Control System sends alarm and arm status information to the wireless siren’s receiver. This requires that you
register the Control System to the wireless siren’s receiver. For information on registration and deletion, see p. 35, 7.1
Device Descriptors, and p. 35, 7.2.2 Deleting and Deactivating Wireless Devices.
iConnect
Installation Manual
41
7 Devices
7.7.1.
Wireless Siren Delay
The Wireless Siren Delay is the period of time during which the wireless siren is not sounded after an alarm is triggered
by Normal, Follower or 24Hr zones. This feature is implemented only when the system is not fully armed. During the
Wireless Siren Delay, the Control System’s built-in siren is sounded but the alarm report is not sent until the delay has
expired. This gives the user enough time to disarm in the event that the alarm was accidentally triggered during Part or
Perimeter arming. If the user disarms the system during the Siren Delay, an alarm event is not reported to the central
station.
To program the Wireless Siren Delay time:
1.
From the Programming menu, select Devices, Siren, WL Siren Delay [9152].
2.
Enter a Siren Delay time (00-63 seconds), then press '√ʹ.
7.7.2.
Siren Cut-Off
The Siren Cut-Off is the period of time the sirens are activated after an alarm has occurred. You may program a Siren
Cut-Off time in the interval between ten seconds to twenty minutes.
To program the Siren Cut-Off time:
1.
From the Programming menu, select Devices, Siren, Cut-Off [9153].
2.
Enter a Siren Cut-Off time MM:SS (00:10 - 20:00), then press '√ʹ.
7.7.3.
Wired Siren
When the system generates an audible alarm, both the wired built-in siren and the wireless siren are sounded. This
option allows you to disable the alarm from the Control System’s built-in siren. If disabled, the Control System’s builtin siren may still be used to sound arm/disarm and entry/exit tones.
To program the Wired Siren option:
1.
From the Programming menu, select Devices, Wired Siren [9154].
2.
Select Enabled or Disabled.
7.8.
Smartkeys
Smartkeys enable the user to arm and disarm the system without needing to enter a code. You can register up to 12
smartkeys to the system. For information on registration and deletion, see p. 35, 7.2. Wireless Devices. For descriptor
editing, see p. 35, 7.1 Device Descriptors.
Smartkey function existence is model dependant.
7.8.1.
Smartkey Type
You can define each registered smartkey as Controlled or Non-controlled. A Controlled smartkey causes the system to
send arm/disarm event messages to the central station. Non-controlled smartkeys never send arm messages and send a
disarm message only if the system is disarmed after an alarm occurrence.
To program the smartkey type:
1.
From the Programming menu, select Devices, Smartkeys [918].
2.
Select the smartkey you want to program.
3.
From the smartkey’s sub-menu, select Type [#2]; the current setting is displayed.
4.
Select Controlled or Non-controlled.
42
iConnect
Installation Manual
8 Entry/Exit Timers and System Tones
8.
Entry/Exit Timers and System Tones
This chapter explains how to program the time of the Entry/Exit delays and the tones sounded by the built-in siren and
wireless siren during Exit/Entry Delays, arming, disarming, home automation operation and when a trouble condition
is present.
8.1.
Entry/Exit Delay
The Entry/Exit delay timers determine the amount of time the user has to arm or disarm the system before an alarm is
activated.
You can program separate Entry and Exit delays for each arming method.
To program Exit delay timers:
1.
From the Programming menu, select Entry/Exit, Exit Delays [921].
2.
Select the Exit delay you want to program: Full [#1], Part [#2] or Perimeter [#3].
3.
Enter a delay time (000-255 seconds), then press '√ʹ.
To program Entry Delay timers:
1.
From the Programming menu, select Entry/Exit, Entry Delays [922].
2.
Select the Entry Delay you want to program: Full [#1], Part [#2] or Perimeter [#3].
3.
Enter a delay time (000-255 seconds), then press '√ʹ.
8.2.
Arm on Exit
The Arm on Exit feature cancels the unnecessary remainder of the Exit delay that continues to count down after the user
has vacated the premises. This feature automatically arms the system when an Entry/Exit zone is closed during the Exit
delay.
To program the Arm on Exit option:
1.
From the Programming menu, select Entry/Exit, Arm On Exit [923].
2.
Select Enabled or Disabled.
8.3.
Supplementary Entry Delay
The Supplementary Entry Delay is a pre-alarm feature that is employed in the event that the system is not disarmed
during the entry delay. When the entry delay expires, the Control System’s built-in siren is sounded during an
additional entry delay period. At the end of the supplementary entry delay, the system generates a full alarm condition;
the wireless siren is sounded and an alarm event is reported to the central station.
To program the Supplementary Entry Delay setting:
1.
From the Programming menu, select Entry/Exit, Supp. Ent. Delay [924].
2.
Select Enabled or Disabled.
8.4.
Entry Deviation
Entry Deviation is a pre-alarm feature employed in the event that a detector defined with the Normal zone type is
opened during the entry delay. In this case, the Control System’s built-in siren is sounded until the end of the entry
delay period. Failure to disarm by the end of the entry delay causes the system to generate an alarm.
To program the Entry Deviation setting:
1.
From the Programming menu, select Entry/Exit, Ent. Deviation [925].
2.
Select Enabled or Disabled.
8.5.
Arming Tones
Arming tones are the tones sounded by the Control System’s built-in siren and/or the wireless siren when arming and
disarming the system. Each set of tones can be enabled or disabled according to the requirements of the installation.
iConnect
Installation Manual
43
8 Entry/Exit Timers and System Tones
8.5.1.
Exit Delay Tones
To program tones sounded by the wireless siren during the Exit delay:
1.
From the Programming menu, select Tones, Exit Tones, WL Siren [9311].
2.
Select Enabled or Disabled.
To program tones sounded by the built-in siren during the Exit delay:
1.
From the Programming menu, select Tones, Exit Tones, Siren [9312].
2.
Select No Tones, Four Tones or Continuous Tones.
8.5.2.
Entry Delay Tones
To program tones sounded by the wireless siren during the Entry Delay:
1.
From the Programming menu, select Tones, Entry Tones, WL Siren [9321].
2.
Select Enabled or Disabled.
To program tones sounded by the built-in siren the Entry Delay:
1.
From the Programming menu, select Tones, Entry Tones, Siren [9322].
2.
Select No Tones, Four Tones or Continuous Tones.
8.5.3.
Arming Tones
To program tones sounded by the wireless siren on arming:
1.
From the Programming menu, select Tones, Arm Tones, WL Siren [9331].
2.
Select Enabled or Disabled.
To program tones sounded by the built-in siren on arming:
1.
From the Programming menu, select Tones, Arm Tones, Siren [9332].
2.
Select Enabled or Disabled.
8.5.4.
Disarming Tones
To program tones sounded by the wireless siren on disarming:
1.
From the Programming menu, select Tones, Disarm Tones, WL Siren [9341].
2.
Select Enabled or Disabled.
To program tones sounded by the built-in siren on disarming:
1.
From the Programming menu, select Tones, Disarm Tones, Siren [9342].
2.
Select Enabled or Disabled.
8.6.
Home Automation Tones
Home Automation tones are sounded when you control HA units using keypads or keyfob transmitters.
To program built-in siren Home Automation tones:
1.
From the Programming menu, select Tones, HA Tones [935].
2.
Select Enabled or Disabled.
8.7.
System Trouble Tones
System trouble tones are sounded to provide an audible indication that a system trouble condition exists. On hearing
these tones the user is then able to determine which trouble condition is present from the front panel keypad. For
additional information, see p. 15, 3.5.1 System Trouble Tones.
8.7.1.
Trouble Tones
The Trouble Tones option allows you to enable or disable audible trouble annunciation.
To program the Trouble Tones option:
1.
From the Programming menu, select Tones, Trouble Tones [936].
2.
Select Enabled or Disabled.
44
iConnect
Installation Manual
8 Entry/Exit Timers and System Tones
8.7.2.
Telephone Trouble Tones
Most trouble tones are not sounded between 10:00pm and 7:00am so as not to disturb the user late at night. Telephone
trouble, however, may be an attempt to sabotage the system by cutting the telephone wires. For this reason, you can
program telephone trouble tones to sound at all times.
To program the Telephone Trouble Tones option:
1.
From the Programming menu, select Tones, Tel. Trb. Tones [937].
2.
Select Immediate or Delayed.
8.7.3.
Fire Trouble Tones
The Fire Trouble Tones option is a feature designed to repeat fire-related trouble tones until the problem has been taken
care of. If this feature is enabled, fire trouble tones will be repeated 3½ hours after the user has manually silenced the
tones if the trouble condition has not been restored.
To program the Fire Trouble Tones option:
1.
From the Programming menu, select Tones, Fire Trb. Tones [938].
2.
Select Enabled or Disabled.
It is not necessary to program the Telephone Trouble Tones and Fire Trouble Tones options
if the Trouble Tones option is programmed as disabled.
8.8.
Tones Options
8.8.1.
Tones Output
The Tones Output option enables you to determine whether the tones sounded when arming and disarming are
sounded by the Control System’s built-in siren or its built-in speaker.
To program the Tones Output option:
1.
From the Programming menu, select Tones, Tones Options, Tones Output [9391].
2.
Select Siren or Speaker.
8.8.2.
Control Panel Speaker Volume
The Control Panel Speaker Volume option determines the volume level of the tones sounded by the control panel
speaker.
To program the Control Panel Speaker Volume option:
1.
From the Programming menu, select Tones, Tones Options, CP Speaker Vol. [9392].
2.
Select High, Medium, Low or Mute.
It is not necessary to program the Speaker Volume option if "Siren" is selected for the Tones
Output option.
8.8.3.
Wireless Keypad Speaker Volume
The Wireless Keypad Speaker Volume option determines the volume level of the tones sounded by the Wireless
Keypad speaker.
To program the Wireless Keypad Volume option:
1.
From the Programming menu, select Tones, Tones Options, KP Volume [9392].
2.
Select the Wireless Keypad (1-4) that you want to program.
3.
Select High, Medium, Low or Mute.
iConnect
Installation Manual
45
9 System Options
9.
System Options
As the name suggests, System Options are settings that affect the entire system. This chapter offers explanations and
programming instructions for each of these options.
9.1.
Swinger Setting
A detector defined as Swinger enabled can generate only a limited number of alarms during a specific time period or
during an arming period. The following options are available:
• One alarm per arming period
• One alarm per hour
• One alarm per day
• One alarm per week
• No swinger
To program the Swinger setting:
1.
From the Programming menu, select System Options, Swinger [9401].
2.
Select a Swinger setting from the list.
9.2.
Code Lockout
The Code Lockout option locks the keypad for 30 minutes if five unsuccessful attempts are made to enter the user code.
To program the Code Lockout setting:
1.
From the Programming menu, select System Options, Code Lockout [9402].
2.
Select Enabled or Disabled.
During the 30-minute lockout period, you can still arm and disarm the system using keyfobs
and smartkeys. If one key arming is enabled, you may still arm the system using the
keypads.
9.3.
Arm/Disarm Options
The options offered in this section relate to arming and disarming the system.
9.3.1.
Forced Arm
Forced arming enables you to arm the system when the system is not ready. This option allows you to enable or disable
Forced arming for the entire system. Additionally, you can enable or disable Forced arming for each individual zone.
For further information, see p. 38, 7.3.6 Force Arm.
To program the Forced Arm setting:
1.
From the Programming menu, select System Options, Arm/Disarm, Forced Arm [94031].
2.
Select Enabled or Disabled.
9.3.2.
One-Key Arming
You can arm the system by pressing any of the three arming keys on the keypad. If One-Key Arming is enabled, the
system does not prompt you for a user code.
To program the One-Key Arming setting:
1.
From the Programming menu, select System Options, Arm/Disarm, One-Key Arming [94032].
2.
Select Enabled or Disabled.
46
iConnect
Installation Manual
9 System Options
9.3.3.
Supervised Arm
The Supervised Arm option is a feature designed to supervise a wireless device activity before you arm the system. If
the system has not received a transmission from a detector during the interval defined for this option, all arming
methods that include that detector will not be available. Medical, Panic, Fire, Gas, Flood, and Environmental zones are
not included in this supervision and do not affect the system’s ability to arm.
Press to check which detector is causing the "System Not Ready" condition.
To make the required arming method available, activate the detector. PIR detectors have a three-minute delay between
transmissions.
If activating the detector does not help, there may be a problem with the detector. You can bypass the faulty detector’s
zone to allow system arming until the problem is remedied – see p. 21, 4.3 Zone Bypassing/Unbypassing.
Zone bypassing is valid for one arming period only. All bypassed zones are automatically
unbypassed when the system is disarmed.
To program the Supervised Arm interval:
1.
From the Programming menu, select System Options, Arm/Disarm, Superv. Arm [94033].
2.
Enter a Supervised Arm interval (001-255 minutes or 000 to disable the Supervised Arm option).
Do not program a Supervised Arm interval that is less than the detector’s supervision time.
9.3.4.
Instant Arming
Instant arming is a feature that allows you to cancel the entry delay after arming the system – see p. 18, 3.7.2 Instant
Arming. The feature is designed for use in situations where the system’s perimeter is armed and nobody is expected to
enter the premises from outside during the armed period.
To enable/disable the Instant Arm option:
1.
From the Programming menu, select System Options, Arm/Disarm, Instant Arming [94034].
2.
Select Enabled or Disabled.
9.3.5.
Keyfob Disarm
The Keyfob Disarm option enables you to determine whether it is possible for the user to disarm the system using their
keyfob at all times or during the entry delay only.
This feature can be applied only after the system has been fully armed.
1.
From the Programming menu, select System Options, Arm/Disarm, KF Disarm [94035].
2.
Select Always or On Entry.
9.3.6.
Supervised Arm Mode
For the Supervised Arm option, you can choose whether the Control System waits for a transmission of all the devices
included in this supervision, or from at least one of them – see p. 47, 9.3.3 Supervised Arm.
To program the Supervised Arm mode:
1.
From the Programming menu, select System Options, Arm/Disarm, Super Arm Mode [94036].
2.
Select All Reg. Devices or Any Reg. Devices.
9.4.
Panic Alarm
SOS Panic alarms generated from the front panel, keypads or keyfobs can be defined as either audible or silent.
To program the Panic Alarm setting:
1.
From the Programming menu, select System Options, Panic Alarm [9404].
2.
Select Audible or Silent.
iConnect
Installation Manual
47
9 System Options
9.5.
AC Loss Delay
The AC Loss Delay is the amount of time that has to elapse before an AC Loss report is sent to the central station. If AC
power is restored before the event message is sent, the event message is canceled and will not be sent. You can program
an AC Loss Delay to be between 1 and 255 minutes after the system first senses the AC loss condition. Alternatively you
can program a random AC Loss Delay.
The AC Restore message is also sent using the same method described above. AC Restore is reported only if the AC
Loss report was sent.
To program the AC Loss Delay:
1.
From the Programming menu, select System Options, AC Loss Delay [9405].
2.
Enter a delay time (001-255 minutes) or enter 000 if you require the system to choose a random AC Loss Delay,
and then press '√ʹ.
9.5.1.
Random AC Loss Delay
In the event of AC loss, an event message is sent to the central station between 15 and 30 minutes after the AC loss
condition is sensed. The system chooses this delay at random in order to prevent the central station being inundated by
simultaneous AC Loss reports in the event of a regional power cut.
9.6.
Display Options
The following options relate to the information the system displays on the front panel keypad and the LCD keypad.
9.6.1.
Arm Status Display
The Arm Status Display includes the current arm status and any trouble conditions that may exist within the system.
You can program the system to display this information at all times, only for two minutes, or only for 30 seconds after
arming or disarming the system.
To program the Arm Status Display options:
1.
From the Programming menu, select System Options, Display, Arm Status [94061].
2.
Select Display Always, Display 2 Min, or Display 30 sec.
9.6.2.
Banner
The Banner is the 16-character text that you can program to appear on the top row of the LCD display. This text replaces
the arm status if it is programmed to display for two minutes or 30 seconds only – see p.48, 9.6.1 Arm Status Display.
To edit the Banner text:
1.
From the Programming menu, select System Options, Display, Banner [94062].
2.
Edit the Banner text using the alphanumeric keypad, then press '√ʹ.
The system never displays the Banner text if the Arm Status Display option is programmed
as Always.
9.6.3.
Time/Date Format
This option determines the format in which the time and date are displayed.
The following options are available:
• DD/MM/YY, 24Hr
• MM/DD/YY, 24Hr
• DD/MM/YY, 12Hr
• MM/DD/YY, 12Hr
To program the Time/Date format:
1.
From the Programming menu, select System Options, Display, Time Format [94063].
2.
Select the required format from the options available.
9.6.4.
Supervision Loss Indication
This option enables you to select whether the system trouble display will indicate transmitter supervision loss to the
user.
48
iConnect
Installation Manual
9 System Options
To program the Supervision Loss Indication setting:
1.
From the Programming menu, select System Options, Display, SV Loss Ind. [94064].
2.
Select Enabled or Disabled.
9.7.
PGM Output Options
PGM (1-2) and are programmable outputs that are triggered according to specific system status conditions, or by
remote command sent via PSTN, GSM, keyfob, keypad, or RP.
9.7.1.
Output Trigger
The Output Trigger option determines the conditions that activate and deactivate the PGM output.
To program the Output Trigger:
1.
From the Programming menu, select System Options, PGM Options [9407].
2.
Select a PGM Output.
3.
Select Output Trigger [#1].
4.
Select an Output Trigger option from the following table.
Table 9-1: PGM Output Trigger Options
Trigger Option
PGM Not Used
Full Arm
Perimeter Arm
Part Arm
Arm Status
Power Trouble
Tel. Line
Trouble
System Trouble
Medical
Burglary
Fire Alarm
Zone Status*
Entry/Exit
Siren
WL Siren
Telecontrol
Activated by…
The PGM output is disabled
System "Full" armed
System "Perimeter" armed
System "Part" armed
Any arming method
AC Loss or Low Battery conditions
Deactivated by…
Telephone line supervision trouble
Telephone line restore
System trouble condition
Medical alarm
Burglary alarm
Fire alarm
System trouble restore
Open zones (steady)
Bypassed zones (pulsing)
Entry/Exit delay follower
Built-in siren follower
Wireless siren follower
System disarmed or PGM Cut-off
AC restore or Battery restore
Any arming method, system disarmed or
PGM Cut-off
All zones closed and no zones bypassed
Remote PGM activation (PSTN/GSM/keyfob/keypad/RP, or via Internet in ELAS versions
321 and above)
For certain trigger options, deactivation may be determined by the PGM Cut-off -- see p. 50,
9.7.4 PGM Cut-off. If the PGM Cut-off is programmed as 000 (continuous activation), the
PGM output shall remain activated until it is toggled by the relevant change in system
status.
9.7.2.
Output Type
The Output Type option determines whether the PGM output produces a steady or pulsed output.
To program the Output Type:
1.
From the Programming menu, select System Options, PGM Options [9407].
2.
Select a PGM Output.
3.
Select Output Type [#2].
4.
Select Steady or Pulsed.
The Zone Status, Siren and WL Siren trigger options have a fixed Output Type; there is no
need to program an Output Type for these options.
*
Zone Status functions only when the system is disarmed.
iConnect
Installation Manual
49
9 System Options
9.7.3.
Polarity
You can determine the polarity of the PGM output from the following two options:
• Active High: The output is normally off and is switched on when activated.
• Active Low: The output is normally on and is switched off when activated.
To program the Polarity:
1.
From the Programming menu, select System Options, PGM Options [9407].
2.
Select a PGM Output.
3.
Select Polarity [#3].
4.
Select Active High or Active Low.
9.7.4.
PGM Cut-off
The PGM Cut-off is the duration for which the PGM is activated. Certain Output Trigger types are deactivated after the
PGM Cut-off time has expired– see, 9.7.2, Output Type. For those Output Trigger types that are not affected by the
PGM Cut-off, there is no need to program this option.
If, for example, Output Trigger option is set to Full Arm, and PGM Cut-off time is 060 seconds; then PGM is activated
by Full Arming and deactivated by disarming or by PGM Cut-off Time, whichever comes first. If this option is set to
"000" (Continuous activation), PGM is activated by Full Arming, and deactivated by disarming.
To program the PGM Cut-off time:
1.
From the Programming menu, select System Options, PGM Options [9407].
2.
Select a PGM Output.
3.
Select PGM Cut-off [#4].
4.
Enter a PGM Cut-off time (001-255 seconds or 000 for continuous activation), then press '√ʹ.
9.8.
Guard Code
Guard Code is an option that allows a security guard to check the premises in case of an alarm and to perform basic
functions such as view log etc.
After two minutes since an alarm occurs, the Guard Code becomes active and the security guard can enter the premises
and disarm the system using this code. Installer codes authorization also extends to allow arming and disarming.
Guard Code is active within five minutes since the system is armed. After five minutes, the Guard code is revoked, and
the installer code regular authorization is restored.
Guard code is also active when the system is disarmed.
When the Guard Code option is enabled, the Guard Code Control [94221] and Guard code
report [94222] options must be disabled.
To program the Guard Code:
1.
From the Programming menu, select System Options, Guard Code. [9408].
2.
Select Enabled or Disabled.
3.
Edit the User Code 31 (see p. 22, 4.4.1 Editing User Codes).
When the Guard Code is disabled, it is not valid even if programmed with a value other
than 0000.
9.8.1.
Guard Code Control
Guard Code Control option sets the Guard control value based on account #1, but in reversed order (e.g., the account #1
is set to 88881234, then the Guard Code is set to 4321).
When the Guard Code Control option is enabled, the Guard Code option [9408] must be
disabled.
The installer may use hex digits in the account number; the Guard Code will then be set to
0000.
If the automatically calculated Guard Code is the same number as an existing user code, it
will be set to 0000.
50
iConnect
Installation Manual
9 System Options
To program the Guard Code Control option:
1.
From the Programming menu, select System Options, Guard Code CT, Guard Code Ctr. [94221].
2.
Select Enabled or Disabled.
Clear Users function also clears the Guard Code even if the Guard Code Control is set as
Enabled.
9.8.2.
Guard Code Report
Guard Code Report option allows reporting of the Arm/Disarm events (including Disarm after an Alarm) to the Central
Station even if the Arm/Disarm event group reporting is disabled – see p. 64, 10.9.1 Event Reporting.
When the Guard Code Report option is enabled, the Guard Code option [9408] must be
disabled.
To Activate the Guard Code Control option:
1.
From the Programming menu, select System Options, Guard Code, Guard Code CT, Guard Code Rep [94222].
2.
Select Enabled or Disabled.
9.9.
"No Arm" Indication
The "No Arm" indication is a feature designed to inform the central station that the system has not been armed for a
specified period of time.
To define the "No Arm" indication interval:
1.
From the Programming menu, select System Options, No Arm Ind. [9409].
2.
Select 1 Week, 2 Weeks, 3 Weeks, 4 Weeks or Disabled.
The No Arm event message is an unclassified event. This means that it does not belong to
any event group. If the No Arm option is programmed with any option other than
"Disabled", the event message will be sent.
9.10. Jamming Detection
The system is able to detect RF Jamming that is usually caused by an intruder attempting to compromise the security
system.
To program the Jamming Detection setting:
1.
From the Programming menu, select System Options, Jamming Det. [9410].
2.
Select Enabled or Disabled.
9.11. "No Motion" Time
The No Motion feature is designed to monitor the activity of disabled or elderly people. If a detector defined as "No
Motion" (see p. 37, 7.3.1 Zone Type) has not detected within a pre-defined period of time, a No Motion event message is
sent to the central station.
To program the No Motion time:
1.
From the Programming menu, select System Options, No Motion [9411].
2.
Enter the No Motion time value between 00:00 and 72:00. To disable the No Motion feature, enter 00:00. Press '√ʹ.
9.12. Microphone/Speaker Options
In addition to the built-in microphone and speaker, the iConnect
Control System Control System supports an
external microphone/speaker unit called Interphone. The Microphone/Speaker option allows you to choose which
microphone and speaker are in use. You can choose one mic./speaker (internal or external) to function exclusively or
both may function simultaneously.
To program the Microphone/Speaker option:
1.
From the Programming menu, select System Options, Mic./Speaker [9412].
2.
Select Internal, External or Internal & External.
iConnect
Installation Manual
51
9 System Options
9.13. Vocal Messages
The Vocal Messages option allows you to enable/disable vocal annunciation of system status. When this feature is
enabled, the system plays a short message to announce events such as arming and disarming.
To program the Vocal Messages option:
1.
From the Programming menu, select System Options, Vocal Message [9413].
2.
Select Enabled or Disabled.
The availability of the Vocal Message annunciation feature is hardware dependent.
9.14. Installer Access
The Installer Access option determines if the Installer code can access the system at all times or only after the Master
code provides authorization with the Enable Programming command – see p.27, 4.7.12 Enable Programming.
To program the Installer Access option:
1.
From the Programming menu, select System Options, Install. Access [9414].
2.
Select Always or User Initiated.
9.15. Auto Log View
Auto Log View is a future option that is not available in the current firmware. The default setting for this option is
disabled. Electronics Line 3000 recommends that you do not change this setting.
9.16. Daylight Savings
Using the Daylight Savings option, the system is able to automatically adjust its clock twice a year according to the
national adjustment to Daylight Saving Time.
Two options are available:
• Europe – the clock is adjusted forward 1hr on the last Sunday in March at 1am, the clock is adjusted back
1hr on the last Sunday in October at 1am.
• USA– the clock is adjusted forward 1hr on the second Sunday in March at 2am, the clock is adjusted back
1hr on the first Sunday of November at 2am.
To program the Daylight Savings option:
1.
From the Programming menu, select System Options, Daylight Savings [9416].
2.
Select Europe, USA or Disabled.
52
iConnect
Installation Manual
9 System Options
9.17. Standard Type
By choosing one of the existing security standards you can change the Control System behavior accordingly.
To set the standard type:
1.
From the Programming menu, select System Options, Standard Type [9417].
2.
Select Regular, EN-50131 or Skafor.
9.17.1. EN-50131 Standard Type
Settings the Standard type to EN-50131 changes some of the Control System settings as described below.
Arm Prevention for EN-50131
The system cannot be armed in the following cases:
• Media Loss, Supervision Loss, or Device Trouble condition in all Active Communication1 modules -GPRS and/or GSM, and/or PSTN2;
• Trouble condition (Transmitter Out of Synch, Supervision Loss, or Zone Trouble) from any Zone,
including Fire, Gas, Flood, and Environmental;
• Entry/Exit Trouble - System not ready is displayed on the Control System’s LCD.
In an attempt to remotely arm the system the remote arming device is notified as follows:
• When arming by SMS – an SMS message "Command refused" is sent to the cellular phone;
• When arming by DTMF – a negative error tone is sounded;
• When arming from WUApp – System not Ready message is displayed.
Tamper Behavior for EN-50131
Opening of any tamper switch while the Control System is disarmed causes the Control System to send an alert. If the
EN-50131 standard is chosen, the siren is not activated in this case. For other standards (Skafor, Regular), the siren is
activated.
Number of Events from Single Source for EN-50131
The EN-50131 standard requires that the system avoid multiple events being generated from a single source. The
number of repeated events from the same source during any Arm or Disarm period is limited to three. Two kinds of
event types are defined for each device: Alarm/Tamper event and fault/trouble event. Every device can have maximum
of three events from each type registered in the log. After the third event from the same source, no more events are sent
to CS. Counters are reset each time the system is armed or disarmed.
EN-50131 Required Settings
To meet the requirements of the EN-50131 standard:
• Set Supervision Time to 2 hours – see p.36, 7.2.3 Supervision Time;
• Set Supervised Arm to 20 minutes – see p. 47, 9.3.3 Supervised Arm;
• Set Entry Delay to 45 sec. maximum – see p. 43, 8.1 Entry/Exit Delay;
• Set Arm Status Display to 30 sec. -- see p. 48, 9.6.1 Arm Status Display;
• Set Entry/Exit Trouble to "Enabled"
Active communication module is a module used for events reporting.
If there is only one communication module (GPRS, PSTN, or GSM), any communication trouble prevents the Control System from
arming.
1
2
iConnect
Installation Manual
53
9 System Options
9.18. Battery Type
The battery type must be defined according to the battery supplied with the system (for example, if the battery sticker
reads 1500 mAh, choose 1.5 Ah, if 3000 mAh, choose 3.0 Ah).
To program the battery type:
1.
From the Programming menu, select System Options, Battery Type [9418].
2.
Select the battery type.
9.19. Report Fail Trouble
If the Report Fail Trouble option is enabled, failure to report an event displays System Trouble on the LCD display.
Report Fail Trouble is displayed after the control system has exhausted all message attempts and report cycles when
trying to report the event. To restore a System Trouble condition caused by failure to report, press until you have
scrolled through the entire system trouble list. If the Report Fail Trouble is disabled, failure to report an event does not
cause a system trouble condition.
To program the Report Fail Trouble option:
1.
From the Programming menu, select System Options, Rep. Fail Trb. [9419].
2.
Select Enabled or Disabled.
9.20. Immediate Arming from WUApp
If immediate arming from WUApp is enabled, all WEB Arm commands received are executed immediately regardless
of the programmed Exit Delay – see p. 43, 8.1 Entry/Exit Delay. If disabled, the ARM commands will be executed with
the programmed Exit Delay.
1.
From the Programming menu, select System Options, WEB Immed. Arm [9420].
2.
Select Enabled or Disabled.
9.21. T014A Standard
To turn on the T014A functionality, perform the following procedure:
For this functionality to function, the EN-50131 standard must be chosen.
1.
From the Programming menu, select System Options, T014A, Enable T014A [94211].
2.
Select Enable or Disable.
To reset messages:
1.
From the Programming menu, select System Options, T014A, Message Reset [94212].
2.
Press "'√ʹʺ to reset the messages.
The system Prompts: "Messages Reset OK?"
9.22. Alarm Memory Reset
The Alarm Memory Reset feature enables the installer to enable or disable the alarm reset procedure. This procedure, if
enabled, ensures that once an armed control system has been disarmed all alarm LED indicators are automatically
deactivated (reset).
To set the alarm memory reset feature; perform the following procedure:
1.
From the Programming menu, select System Options, Al. Mem. Reset [9422].
2.
Select Enable or Disable.
54
iConnect
Installation Manual
10 Communications
10. Communications
This section explains how to determine the way the Control System communicates via the GPRS, GSM, Ethernet and
PSTN modules to the Central Station and to the user.
10.1. System Reporting
The Control System supports six report accounts for central station and user reporting. Each account has its own
telephone number and communications options. The first account is always primary, every other account (that is not a
voice report) may be chosen as primary or backup. Each primary account may have one, several, or no backup accounts
at all. The order of calling is the following:
1.
First, the Control System calls all the primary accounts, in ascending order. In case a primary account report fails,
the Control System calls the backup accounts.
2.
After that, the system calls the Voice Report accounts – see p. 57, 10.3 Vocal Message Dialer.
If account is set as Backup after Voice Report account, reports to this account will be discarded. It is Installer
responsibility to program primary and backup accounts in proper order. To ensure proper functionality,
Installer will not be able to set Account 1 as Voice Report or Backup.
10.1.1. Telephone Number
To edit an account’s telephone number:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (1-6).
3.
From the account’s sub-menu, select Phone Number [#1].
4.
Enter up to 16 digits. Use the key to enter "", "#", "," (pause), "T" (switch to DTMF tone dialing), "P" (switch to
pulse dialing) or "+" (international code). Use the key to delete one character at a time. Press '√ʹ.
10.1.2. Protocol
To program an account’s communication protocol:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (1-6).
3.
From the account’s sub-menu, select Protocol [#2].
4.
Select a protocol from the options available.
Set account 1 to IP protocol if you use GPRS communication. Account number 3 is designed for use with
the Follow me feature. It is the only telephone number that can be programmed by the user.
10.1.3. Communication Interface
For each account, you can choose whether the system employs PSTN, GSM, Ethernet (LAN), or GPRS communication.
To program an account’s communication interface:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program account (1-6).
3.
From the account’s sub-menu, select Interface [#3].
4.
Select PSTN, GSM, LAN, or GPRS (GPRS or LAN is used only for the first account).
10.1.4. Two-Way Audio
The Two-Way audio option determines whether Two-Way Audio is enabled for the account. For further information,
see p. 31, 5.2.2 TWA Alarm Reporting.
To program the Two-Way Audio option for an account:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (1-6).
3.
From the account’s sub-menu, select Two-Way Audio [#4].
4.
Select Enabled or Disabled.
iConnect
Installation Manual
55
10 Communications
10.1.5. Account Number (not available for voice report)
To edit an account number:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (1-6).
3.
From the account’s sub-menu, select Account Number [#5].
4.
Enter up to eight digits. Enter leading zeros for account numbers of less than eight digits. Use the
hexadecimal digits. Press '√ʹ .
key to enter
If the programmed protocol is Contact ID, "A" is not a valid entry in the account number.
10.1.6. Call Attempts (not available for voice report)
The Call Attempts option determines the number of times the system tries to call a telephone number before moving on
to the next number in sequence.
To program the number of call attempts for an account:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (1-6).
3.
From the account’s sub-menu, select Call Attempts [#6].
4.
Enter a value between 01 and 15. Press '√ʹ.
10.1.7. Account Type (not available for voice report)
To program the account type for an account:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (2-6).
3.
From the account’s sub-menu, select Account Type [#7].
4.
Select Primary or Backup.
Account 1 is by default set as a primary account.
10.2. Report Cycles
The system’s attempts to report events are organized in cycles. A report cycle is a set of call attempts – see p. 56, 10.1.6
Call Attempts (not available for voice report). If the system does not succeed in sending a report to any of the telephone
numbers, it tries to dial the entire report cycle again until it sends a successful report. You can determine the number of
times the system attempts to dial this sequence by programming the Report Cycle option.
To program the number of Report Cycles:
1.
From the Programming menu, select Communications, Accounts, Report Cycles [9517].
2.
Enter a value between 01 and 15. Press '√ʹ.
In the example illustrated in Figure 10-1, Account 1 is programmed with 2 call attempts, Account 2 is programmed with
3 call attempts and the number of report cycles programmed is 3.
Figure 10-1: Typical Report Cycle Sequence
56
iConnect
Installation Manual
10 Communications
10.3. Vocal Message Dialer
The Vocal Message Dialer is a feature that calls the user’s telephone number when specific events occur and plays prerecorded messages. These calls are made after the system has reported the events to the central station. Additionally, in
the event of an alarm, the user is able to establish a Two-Way Audio connection on receiving the vocal message in order
to check the premises.
The system supports up to five Voice Report accounts. Each account has its own telephone number, communication
interface and Two-Way Audio options.
The types of event that are reported using the Vocal Message Dialer feature are determined in VM Event Options – see
p. 65, 10.10 Vocal Message Dialer Event Options.
If one of these events occurs, the Control System dials the phone numbers of the Voice Report Account.
The sequence for a vocal message call is as follows:
1.
An event occurs and the Control System calls the telephone number of the first Voice Report Account chosen.
2.
When the user answers the call, the Home ID message and the relevant event message are played.
3.
The user presses 1 on their telephone; if there are additional events to report the next message is played.
Otherwise, "No Further Messages" is announced.
-orIf Two-Way Audio is enabled for the Voice Report account, the user may open the audio channel by
pressing 2 on their telephone. If the user does not want to open the audio channel they may press ""
then "#" on their telephone to hang up.
If the call is not answered or the TC/VM Timeout (see p. 61, 10.6.9 Telecontrol/Vocal Message Timeout) expires before
the message is acknowledged by the user pressing 1, the Control System calls the next Voice Report Account telephone
number.
The availability of the Vocal Message Dialer feature is hardware dependent.
10.3.1. Telephone Number
To edit a Voice Report Account account’s telephone number:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (2-6).
3.
From the account’s sub-menu, select Phone Number [#1].
4.
Enter up to 16 digits. Use the key to enter "", "#", "," (pause), "T" (switch to DTMF tone dialing), "P" (switch to
pulse dialing) or "+" (international code). Use the key to delete one character at a time. Press '√ʹ when you
have finished editing.
10.3.2. Protocol
To program voice report protocol:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (2-6).
3.
From the account’s sub-menu, select Protocol [#2].
4.
Select Voice Report.
10.3.3. Communication Interface
For each Vocal Message account, you can choose whether the system employs cellular or PSTN communication.
To program a Voice Report Account’s communication interface:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (2-6).
3.
From the account’s sub-menu, select Interface [#3].
4.
Select GSM or PSTN.
10.3.4. Two-Way Audio
The Two-Way audio option determines whether Two-Way Audio is enabled for the Voice Report Account. For further
information, see p. 31, 5.2.3 Two-Way Audio after Vocal Messages.
iConnect
Installation Manual
57
10 Communications
To program the Two-Way Audio option for a Voice Report Account:
1.
From the Programming menu, select Communications, Accounts [951].
2.
Select the account you want to program (2-6).
3.
From the account’s sub-menu, select Two-Way Audio [#4].
4.
Select Enabled or Disabled.
10.3.5. Home ID
The Home ID is a short message that is played at the beginning of a vocal message call in order to identify the system to
the user. For example, at the beginning of the vocal message call, the message "Michael’s House" will be played before
the event messages.
To play back the Home ID message:
• From the Programming menu, select Communications, Accounts, Home ID, Play Message [95181].
To record a Home ID message:
1.
From the Programming menu, select Communications, Accounts, Home ID, Record Message [95182].
2.
Press '√ʹ to start recording the message.
3.
Record your message. The message may be up to ten seconds long.
4.
Press '√ʹ to stop recording; the message is automatically played back and OK? is displayed. Press ʹ√ʹ to save your
recording.
10.4. Remote Programming
Electronics Line 3000’s Remote Programmer (RP) and WEB Remote Programmer software enable you to operate and
program the system from a PC either on-site or from a remote location. The software provides a comprehensive
Control System designed to facilitate programming. There are 3 access levels available:
interface to the iConnect
Supervisor (full access), Technician (limited access to the program, a technician is not able to view or change user codes
or the RP access code), and Operator (access to user operations, such as arming and disarming the system).
10.4.1. Remote Programmer
PC to Control System Connection Methods
You can connect to the Control System from a PC using one of three methods:
• Direct Call: The RP calls the site, the system picks up and RP communication is established.
• Callback: The RP calls the site, the system picks up then hangs up. The system then calls the Callback
telephone number to establish a connection.
• Serial Connection: The RP connects directly via the USB port on the communication module (this method
requires installation of the Control System USB Driver).
The following programming options relate to the method in which the Remote Programmer software connects with the
system.
Callback Telephone Number
RP Callback is a security feature that helps ensure that remote programming is only performed by authorized
personnel. When the Remote Programmer contacts the Control System, the Control System hangs up and calls the
Callback telephone number.
To edit the Callback telephone number:
1.
From the Programming menu, select Communications, Remote Prog., Call-Back # [9521].
2.
Enter up to 16 digits. Use the key to enter "", "#", "," (pause), "T" (switch to DTMF tone dialing), "P" (switch to
pulse dialing) or "+" (international code). Use the key to delete one character at a time. Press '√ʹ when you
have finished editing.
If there is no Callback telephone number programmed, RP Callback is disabled and the
system connects to the Remote Programmer software using the "direct call" method.
58
iConnect
Installation Manual
10 Communications
RP Passcode
The RP passcode is a six-digit code that grants access to remote programming. When establishing an RP connection, the
passcode programmed in the RP customer file on the PC must be identical to the system’s RP passcode.
To edit the RP passcode:
1.
From the Programming menu, select Communications, Remote Prog., RP Passcode [9522].
2.
Enter six digits, then press '√ʹ.
RP Communication Interface
For remote programming, the iConnect
Control System can employ GPRS, GSM, Ethernet, or PSTN communication.
To program the RP communication interface:
1.
From the Programming menu, select Communications, Remote Prog., RP Interface [9523].
2.
Select PSTN or GSM (GPRS and LAN are relevant for the WEB RP only).
RP Access Options
Options are available to enable, disable or limit access to remote programming.
To program RP Access Options:
1.
From the Programming menu, select Communications, Remote Prog., RP Access [9524].
2.
Select an RP access option from the following table.
Table 10-1: RP Access Options
Access option
Always Enable
During Disarm
Disable
User Initiated
Description
Up/downloading is always possible.
The system must be disarmed in order to establish a connection.
Up/downloading is disabled.
The user must perform Enable Programming from the Service menu in
order to establish a connection – see p.27, 4.7.12 Enable Programming.
10.4.2. WEB Remote Programmer (Relevant only when using ELAS connection)
Electronics Line 3000's WEB-based Remote Programmer (WEB RP) allows the installer or service provider to operate
and program the system via the WEB using ELAS database to get the list of supported Control Systems. To access WEB
RP, the installer must enter user name and password.
10.5. Service Call
The Service Call feature is designed to enable the user to call the monitoring service at the push of a button. When the
user presses the up arrow key button and then presses and holds down the Service Call button
seconds, a two-way audio connection with the central station is established.
for a few
10.5.1. Service Call Telephone Number
To edit the Service Call telephone number:
1.
From the Programming menu, select Communications, Service Call, Phone Number [9531].
2.
Enter up to 16 digits*. Use the key to enter "", "#", "," (pause), "T" (switch to DTMF tone dialing), "P" (switch
to pulse dialing) or "+" (international code). Use the key to delete one character at a time. Press '√ʹ when
you have finished editing.
10.5.2. Service Call Interface
For the Service Call feature, you can choose whether the system employs cellular or PSTN communication.
To program the Service Call interface:
1.
From the Programming menu, select Communications, Service Call, Interface [9532].
2.
Select either GSM or PSTN.
iConnect
Installation Manual
59
10 Communications
10.6. Communications Options
10.6.1. Line Monitor
The Line Monitor feature monitors the PSTN telephone line. If a problem is detected with the line, a Media Loss event
is registered in the log.
To program the Line Monitor setting:
1.
From the Programming menu, select Communications, Comm. Options, Line Monitor [95401].
2.
Select Enabled or Disabled.
10.6.2. Periodic Test Interval
The Periodic Test is a test transmission the system sends to notify the central station that its reporting capability is fully
functional.
Two options are available for the Periodic Test:
• You can program the system to send a Periodic Test message according to a chosen time interval. This time
interval can be between 1 and 254 hours (approximately 10 days).
• The system calculates automatically the time the Periodic Test is sent according to the last four digits of the
account number. Automatically calculated tests can be sent daily, weekly or monthly according to the
Auto Interval option – see p. 60, 10.6.4 Auto Interval. This feature is designed to avoid overflow of test
reports to the central station at any given time.
The Periodic Test event message is an unclassified event. This means that it does not belong
to any event group. If the Periodic Test Interval is programmed with any value other than
000, the event message will be sent.
To program the Periodic Test Interval:
1.
From the Programming menu, select Communications, Comm. Options, Test Interval [95402].
2.
Enter the test interval (001-254 hours) or 255 for an automatically calculated test interval, then press '√ʹ.
To disable the Periodic Test:
• Program the Periodic Test Interval as 000.
10.6.3. First Test
If the Periodic Test Interval is programmed as 001-254 hours, you must also program the time that the first Periodic Test
is sent.
To program the First Test Time:
1.
From the Programming menu, select Communications, Comm. Options, First Test [95403].
2.
Enter a time (HH:MM), then press '√ʹ.
10.6.4. Auto Interval
The Auto Interval option determines the frequency of automatically calculated periodic test messages.
To program the Auto Interval:
1.
From the Programming menu, select Communications, Comm. Options, Auto Interval [95404].
2.
Select Daily, Weekly or Monthly.
10.6.5. Call Timeout
The Call Timeout is the amount of time the system waits for the first acknowledgement (ACK1) from the central station
when reporting using the PSTN. If ACK1 is not received during this time, the system regards the call as a failed dialing
attempt.
To program the Call Timeout:
1.
From the Programming menu, select Communications, Comm. Options, Call Timeout [95405].
2.
Enter a time (001-255 seconds), then press '√ʹ.
10.6.6. ACK. Timeout
The ACK Timeout is the amount of time the system waits for the second acknowledgement (ACK2) from the central
station when reporting using the PSTN. If ACK2 is not received during this time, the system regards the call as a failed
dialing attempt.
60
iConnect
Installation Manual
10 Communications
To program the ACK Timeout:
1.
From the Programming menu, select Communications, Comm. Options, ACK Timeout [95406].
2.
Enter a time (001-255 seconds), then press '√ʹ.
10.6.7. RDM Period
Remote Diagnostics and Maintenance (RDM) session is a feature that is designed to enable automated maintenance of
installed Control Systems. During a maintenance session, the Control System automatically dials the RP Callback
number and connects to the RDM server. The time interval between maintenance sessions is called the RDM period.
To program the RDM period:
1.
From the Programming menu, select Communications, Comm. Options, RDM Period [95407].
2.
Enter the required RDM period (001-255 days or 000 to disable RDM communication).
10.6.8. Incoming Calls
This option determines whether the Control System is able to receive incoming Telecontrol/Two-Way Audio calls.
To program the Incoming Calls option:
1.
From the Programming menu, select Communications, Comm. Options, Incoming Call [95408].
2.
Select Enabled or Disabled.
10.6.9. Telecontrol/Vocal Message Timeout
The Telecontrol/Vocal Message Timeout (TC/VM Timeout) determines the duration of a Telecontrol, Two-Way Audio
or Vocal Message call. In the case of a Telecontrol or Two-Way Audio call, when the time out expires, the system
automatically disconnects unless the call is manually extended by the operator. For Vocal Message calls, if the time out
expires and the user has not acknowledged the message, the system attempts to call the next Voice Report account’s
telephone number. During a Vocal Message call, the timeout is reset each time a message is acknowledged.
To program the Telecontrol/Vocal Message Timeout:
1.
From the Programming menu, select Communications, Comm. Options, TC/VM Timeout [95409].
2.
Enter a time (001-255 seconds), then press '√ʹ.
10.6.10. Speed Dial Timeout
The Speed Dial timeout (SPD DIAL TMO) determines the duration of a Speed Dial call. When the timeout expires, the
system automatically disconnects unless the call is manually extended by the operator.
To program the Speed Dial Timeout:
1.
From the Programming menu, select Communications, Comm. Options, Spd Dial TMO [95410].
2.
Enter a time: (00:00 — 99:59), then press '√ʹ.
10.6.11. TWA Mode
The Two-Way audio features offer a choice of two operation modes:
• Duplex – both parties may speak at once just like a regular telephone.
• Simplex – one party may speak while the other party listens.
To program the TWA mode option:
1.
From the Programming menu, select Communications, Co
2.
mm. Options, TWA Mode [95411].
3.
Select Duplex or Simplex.
10.7. GSM Options
10.7.1. GSM RX Report
The GSM RX Report is a feature that periodically reads the GSM signal strength of the Cellular Communication module
– see p. 27, 4.7.10 GSM Signal Strength. This reading occurs at the times programmed for the Periodic Test – see p. 60,
10.6.2 Periodic Test Interval, and p. 60, 10.6.3 First Test. This means that each time the periodic test is sent, the system
also sends a GSM signal strength report to the central station. The system also enters the GSM signal strength in the
event log.
iConnect
Installation Manual
61
10 Communications
If the Periodic Test is disabled, the GSM RX Report feature will not function. The GSM RX
report belongs to the Peripherals event group – see p. 64, 10.9 Event Options for Central
Station Reporting. If this event group is disabled, the GSM signal strength is still recorded in
the event log.
To program the GSM RX Report option:
1.
From the Programming menu, select Communications, Comm. Options, GSM Options, GSM RX Report [954121].
2.
Select Enabled or Disabled.
10.7.2. PIN Code
The PIN (Personal Identity Number) is a four-digit code that protects the SIM card from unauthorized use if lost or
stolen.
When using a SIM card with an activated PIN code, the installer has to make sure that the PIN code programmed in the
Control System is the same as the SIM card's PIN code. The PIN code should be programmed in the system before
inserting the SIM card in the GSM module.
To program the PIN code:
1.
From the Programming menu, select Communications, Comm. Options, GSM Options, PIN Code [954122].
2.
Edit the four-digit PIN code, then press '√ʹ.
3.
Power up the Control System to apply the new PIN Code definition.
The new PIN code takes effect only after the System is powered up.
If a wrong PIN code was programmed in the system, a System Trouble is generated, PIN Code Error message is
displayed, and GSM communication of any kind is not available. In this case, the SIM card must be reactivated.
To reactivate a SIM card:
1.
Program the correct PIN code in the Control System (see above), then disconnect the Control System from all the
power sources.
2.
Remove the SIM card from the GSM module and insert it into a cellular phone.
3.
Turn on the cellular phone and enter the correct PIN code.
4.
Re-install the SIM card into the Control System and apply power.
10.7.3. SMS Center
To edit the SMS Center telephone number:
1.
From the Programming menu, select Communications, Comm. Options, GSM Options, SMS Center [954123].
2.
Enter up to 16 digits. Use the key to enter "", "#", "," (pause), "T" (switch to DTMF tone dialing), "P" (switch to
pulse dialing) or "+" (international code). Use the key to delete one character at a time. Press '√ʹ when
finished.
10.7.4. SMS Command
The SMS Command option enables you to enable or disable the ability to send commands to the system via SMS. For
further information on SMS commands, see p. 18, 3.7.4 Remote Arming/Disarming via SMS and p. 33, 6.3 Telephone
Control.
To enable/disable SMS commands:
1.
From the Programming menu, select Communications, Comm. Options, GSM Options, SMS Command [954124].
2.
Select Enabled or Disabled.
10.7.5. SMS Confirmation
After an SMS command is executed by the system, a confirmation message is returned to the sender’s mobile phone.
You can enable or disable this feature using this option.
To enable/disable SMS confirmation:
1.
From the Programming menu, select Communications, Comm. Options, GSM Options, SMS Confirm [954125].
2.
Select Enabled or Disabled.
62
iConnect
Installation Manual
10 Communications
10.7.6. GSM Media Loss Time
The GSM Media Loss Time is a feature that is designed to control the amount of GSM media loss events registered in
the log and sent to the central station.
If, for a period defined in GSM ML Time parameter, the GSM signal has always been below the lower threshold, a
Media Loss event is registered in the log and sent to the central station.
The GSM Media Loss event is sent to the central station via PSTN only.
If, for a period defined in GSM ML Time parameter, since GSM media restore is detected, the GSM signal has always
been above the upper threshold, GSM Media Restore is registered in the log and sent to central station.
To disable the GSM Media Loss feature (cancel the GSM Media Loss events) enter 000.
To program the GSM Media Loss Time:
1.
From the Programming menu, select Communications, Comm. Options, GSM Options, GSM ML Time. [954126].
2.
Enter time (003-255 minutes or 000 to disable), then press '√ʹ.
10.8. TWA Event Report Options
10.8.1. TWA Event Report
The TWA Event Report is an event report that is sent to the central station to indicate that Two-Way Audio
communication is about to commence. If enabled, the system sends the Contact ID event code 606000 before
establishing Two-Way Audio communication.
This option affects Contact ID only. If using SIA, a TWA event report is always sent together
with the TC/VM timeout, regardless of the configuration for this option.
To program the TWA Event option:
1.
From the Programming menu, select Communications, Comm. Options, TWA Event Rept. [95413].
2.
Select Enabled or Disabled.
10.8.2. TWA Time Report
If the TWA Time Report option is enabled, the last three digits of the TWA Event Report are replaced with the amount
of seconds programmed for the TC/VM Timeout – p. 61, 10.6.9 Telecontrol/Vocal Message Timeout. For example, if the
TC/VM Timeout is programmed as 120 seconds, the Contact ID event code to be sent for the TWA Event Report will be
606120.
To program the TWA Time Report option:
1.
From the Programming menu, select Communications, Comm. Options, TWA Time Rept. [95414].
2.
Select Enabled or Disabled.
10.8.3. Incoming Number
Incoming number feature allows the installer to program up to three high-priority telephone numbers so that the user
would be able to use Telecontrol/2-way audio over GSM during a GPRS session. If the Control System recognizes the
incoming call as a high-priority call, the GPRS session will be suspended.
To program/edit the Incoming Number:
1.
From the Programming menu, select Communications, Comm. Options, Incoming #. [95415].
2.
Select the telephone number you want to edit (1-3).
3.
Enter up to 16 digits. Use the key to enter "", "#", "," (pause), "T" (switch to DTMF tone dialing), "P" (switch to
pulse dialing) or "+" (international code). Use the key to delete one character at a time. Press '√ʹ when you
have finished editing.
10.8.4. Remote Firmware Update
Electronics Line 3000’s Remote Firmware Update feature allows the Installer or service provider to perform firmware
update from a remote PC using WEB communication.
Before performing the firmware update, locally disarm the system and make sure that there
are no AC LOSS or BATTERY LOW conditions.
iConnect
Installation Manual
63
10 Communications
To setup the firmware update mode:
1.
From the Programming menu, select Communications, Comm. Options, Rem. SW Update [95416].
2.
Select the Remote Firmware Update mode from the following table:
Table 10-2: Remote FW Update
Access option
Always Enable
Disable
User Initiated
10.8.5.
Description
Update is always possible.
Firmware update is not allowed.
The user must perform SW Update from the Service menu in
order to establish a connection – see p. 28, 4.7.14 Remote
Firmware Update.
PSTN Country
In order to meet the requirements of local telecommunications authorities, default telephone line parameters have been
chosen for a number of different countries.
To program the PSTN Country:
1.
From the Programming menu, select Communications, Comm. Options, PSTN Country [95417].
2.
Select your country from the options available.
Electronics Line 3000 offers custom telephone line parameter settings for countries that do not appear in
the list of pre-defined options. If your country does not appear among the available options, select the
option Custom Settings.
10.8.6.
Dial Tone Wait
This option determines whether the system dials only when the dial tone is present or if the dialing is initiated
regardless of the dial tone.
To program the Dial Tone Wait option:
1.
From the Programming menu, select Communications, Comm. Options, Dial Tone Wait [95418].
2.
Select Enabled or Disabled.
10.9. Event Options for Central Station Reporting
System events are divided into a number of different event groups. This division allows you to enable or disable
reporting or Two-Way Audio for a specific group of events.
The different event groups are as follows:
• Burglary [#1]
• Fire [#2]
• Open/Close (arm/disarm) [#3]
• Service [#4]
• Power [#5]
• Peripherals [#6]
• RF Jamming [#7]
• Medical
10.9.1. Event Reporting
You can enable or disable event reporting per Event Group. This allows you to filter the type of events that are reported
to the central station.
To enable or disable reporting for an event group:
1.
From the Programming menu, select Communications, Event Options [955].
2.
Select an Event Group.
3.
From the event group’s sub-menu, select Report [#1].
4.
Select Enabled or Disabled.
64
iConnect
Installation Manual
10 Communications
10.9.2. Restore Reporting
For each event group, you can determine whether restore messages will be sent.
To enable or disable restore reporting for an event group:
1.
From the Programming menu, select Communications, Event Options [955].
2.
Select an event group.
3.
From the event group’s sub-menu, select Report Restore [#2].
4.
Select Enabled or Disabled.
10.9.3. Two-Way Audio
For Burglary, Fire and Medical event groups, there is an additional option that enables Two-Way Audio for that event
group – see p. 31, 5.2.2 TWA Alarm Reporting.
To enable/disable Two-Way Audio for an event group:
1.
From the Programming menu, select Communications, Event Options [955].
2.
Select an Event Group (Burglary, Fire or Medical).
3.
Select TWA [#3].
4.
Select Enabled or Disabled.
10.10. Vocal Message Dialer Event Options
Events reported using the Vocal Message Dialer are divided into event groups that correspond with the pre-recorded
event messages. This allows you to enable or disable the Vocal Message feature for a specific group of events. For
further information on this feature, see p. 57, 10.3 Vocal Message Dialer.
The vocal message event groups and their associated system events are as follows:
Arm [#6]
Burglary [#1]
o
Alarm from Zone (excluding Gas
and Environmental zones)
o
o
o
Zone Tamper
o
o
Zone Fire Alarm
o
o
o
Tamper
Full Arm
Part Arm
Perimeter Arm
Duress
Fire [#2]
Disarm [#7]
User Activated Fire Alarm
o
o
Disarm
o
Zone Water Alarm (Flood)
Disarm after Alarm
Water [#8]
Panic [#3]
o
o
Zone Panic Alarm
User Activated Panic Alarm
Medical [#4]
o
o
o
o
iConnect
Zone Medical Alarm
Zone Medical Alarm
User Activated Alarm
No Motion
Installation Manual
65
10 Communications
System Trouble [#5]
o
o
o
o
o
o
o
o
Battery Low
o
o
o
Supervision Loss
Transmitter Low Battery
AC Loss
Media Loss
Device Trouble
Communication Trouble
Transmitter Out of Synch.
Control System Transmitter Out of
Synch.
Zone Trouble
FM Jamming
To enable/disable the vocal message for an event group:
1.
From the Programming menu, select Communications, VM Event Opt. [956].
2.
Select an event group.
3.
Select Enabled or Disabled.
66
iConnect
Installation Manual
11 Internet Options
11. Internet Options
The following options concern the configuration of the GPRS and Ethernet Communication Modules. In most cases, the
Internet options will be pre-programmed as defaults and you will not be required to change any of the settings apart
from the CPID and password for each customer.
11.1. ELAS Connection Parameters
The following parameters, required to connect Control System to ELAS, are set by ELAS administrator.
11.1.1. Proxy Address
To edit the Proxy Address:
1.
From the Programming menu, select Communications, Internet, Proxy Address [9571].
2.
Enter the Proxy Address IP provided by your ELAS administrator. Use the "1" key to enter ".",
the key to delete one character at a time. Press '√ʹ when finished.
key to insert and
11.1.2. XML Proxy Port
To edit the XML Proxy Port:
1.
From the Programming menu, select Communications, Internet, XML Proxy Port [9572].
2.
Enter the XML Proxy Port provided by your ELAS administrator. Use the "1" key to enter ".",
the key to delete one character at a time. Press '√ʹ when finished.
key to insert and
11.2. Control System Parameters
The following parameters, required to connect Control System to ELAS, should be provided by your ELAS
administrator.
11.2.1. CP ID
To edit the Control System ID:
1.
From the Programming menu, select Communications, Internet, CP ID [9573].
2.
Enter the unique Control System ID provided by your ELAS administrator to connect the Control System to
ELAS. Use the "1" key to enter ".", key to insert and the key to delete one character at a time. The ID
length must be six up to sixteen characters. Press '√ʹ when finished.
11.2.2. CP Password
To edit the Control System Password:
1.
From the Programming menu, select Communications, Internet, CP Password [9574].
2.
Enter the Control System Password provided by your ELAS administrator to connect the Control System to
ELAS. Use the "1" key to enter ".", key to insert and the key to delete one character at a time. The
password length must be six up to sixteen characters. Press '√ʹ when finished.
11.2.3. ELAS Connection On/Off
To enable/disable ELAS connection option:
1.
From the Programming menu, select Communications, Internet, ELAS Connect [9575].
2.
Select Enabled or Disabled.
iConnect
Installation Manual
67
11 Internet Options
11.3. GPRS Network Parameters
The following parameters, required to program your GPRS connection, should be provided by the cellular provider.
11.3.1. APN
To edit the APN name of your GPRS connection:
1.
From the Programming menu, select Communications, Internet, GPRS Options, APN [95761].
2.
Enter the APN name provided by the cellular provider. Use the "1" key to enter ".",
to delete one character at a time.
key to insert and the
key
11.3.2. User Name
To edit the User name of your GPRS connection (optional setting provided by the cellular provider):
1.
From the Programming menu, select Communications, Internet, GPRS Options, User Name [95762].
2.
Enter the User Name provided by the cellular provider. Use the "1" key to enter ".",
to delete one character at a time.
3.
Press '√ʹ when you have finished editing.
key to insert and the
key
11.3.3. Password
To edit the Password of your GPRS connection (optional setting provided by the cellular provider):
1.
From the Programming menu, select Communications, Internet, GPRS Options, Password [95763].
2.
Enter the Password provided by the cellular provider. Use the "1" key to enter ".",
delete one character at a time.
key to insert and the
key to
11.3.4. GPRS Write TMO
To edit the GPRS Write TMO of your GPRS connection:
1.
From the Programming menu, select Communications, Internet, GPRS Options, GPRS Write TMO [95764].
2.
Enter the GPRS Write TMO (015 -255 seconds). Press '√ʹ when finished.
11.4. LAN Network Parameters
The following options concern the configuration of the Ethernet. All of the information required for programming these
options should be provided by the network administrator.
There are two methods of programming the IP settings:
• Automatic IP settings (DHCP) – when using a DHCP server, the server provides all of the configuration
settings automatically.
• Manual IP settings – you must enter the relevant IP addresses, Gateway and Subnet Mask, taking into
consideration your router settings.
11.4.1. LAN IP Address
To edit the LAN IP address:
1.
From the Programming menu, select Communications, Internet, LAN Options, LAN IP Address [95771].
2.
Enter an IP address. Press the
at a time.
key as many times as necessary to select "." and the
key to delete one character
When you choose to use DHCP, set the IP address and Gateway values to "0", and
the subnet mask to 255.255.255.000 (or another value according to your router's
settings); if not, insert the IP Address, Subnet Mask, and Gateway. Press '√ʹ when
you have finished editing.
11.4.2. Subnet Mask
To edit the subnet mask:
1.
From the Programming menu, select Communications, Internet, LAN Options, Subnet Mask [95772].
2.
Enter the Subnet Mask. Press the
character at a time.
68
key as many times as necessary to select "." and the
key to delete one
iConnect
Installation Manual
11 Internet Options
11.4.3. Gateway
To edit the Gateway address:
1.
From the Programming menu, select Communications, Internet, LAN Options, Gateway [95773].
2.
Enter the Gateway’s IP address. Press the
one character at a time.
key as many times as necessary to select "." and the
key to delete
11.4.4. DNS Server
To edit the DNS Server address:
1.
From the Programming menu, select Communications, Internet, LAN Options, DNS Server [95774].
2.
Enter the DNS Server’s IP address. Press the
one character at a time.
key as many times as necessary to select "." and the
key to delete
11.4.5. LAN Write TMO
To edit the LAN Write TMO:
1.
From the Programming menu, select Communications, Internet, LAN Options, LAN Write TMO [95775].
2.
Enter the LAN Write TMO. Press the
character at a time.
key as many times as necessary to select "." and the
key to delete one
11.4.6. Trouble Conditions
The testing and status options of the Internet connection status should provide the installer with the exact source of the
problem when the Control System is not capable of reporting via LAN. See p. 130, Appendix D: Event Table.
iConnect
Installation Manual
69
12 Home Automation Programming
12. Home Automation Programming
This chapter explains the programmable options for the system’s home automation features. The Home Automation
module is an add-on optional extra that you can install inside the Control System’s plastic housing.
The iConnect
System's home automation features require the use of an external powerline interface when used in an 110V/60HZ power system.
12.1. X10 Overview
The Control System’s home automation feature employs the X10 protocol and this enables compatibility with a wide
variety of readily available home automation products.
Before you can start programming the system’s Home Automation features, you should be familiar with the basic
concept behind X10 automation.
X10 is a protocol that enables you to send commands and other data over regular existing power lines. This means that,
using an X10 transmitter (the Control System’s Home Automation module), you can send On/Off commands to X10
receivers (lamp and appliance modules) that are plugged into electricity outlets around the home. From here on, we
will refer to these X10 receivers as "HA units".
Each HA unit has two codes that are used for identification. These codes are known as the House code and the Unit
code and are usually defined by adjusting the dials that appear on the X10 unit. In Figure 12-1, the HA unit is set to
House A, Unit 3.
Figure 12-1: HA Unit Dials
The Control System supports sixteen HA units on one House code. To ensure that the Home Automation features
function correctly, you must abide by the following guidelines.
• The House code must be the same on each HA unit.
• The House code on the HA units must be identical to the House code programmed in the Control System’s
memory – see p.72, 12.3 House Code.
12.2. HA Units
The following sections explain the programming options available for HA units.
12.2.1. Scheduling (not relevant to PGM)
Scheduling allows you to program the Control System to send On/Off commands to an HA unit at specific times. For
information on programming the On Time, Off Time and Schedule for each HA unit, see p. 34, 6.4 Scheduling.
12.2.2. On by Zone
The On by Zone feature allows you to choose two zones that activate the HA unit when triggered. When either one of
these zones is triggered, the system sends an On command to the HA unit according to the unit’s programmed Pulse
Time – see p. 72, 12.2.8 Pulse Time. For example, you have a magnetic contact installed above the front door. When the
door is opened, the hall light is lit.
To select the detectors that activate an HA unit:
1.
From the Programming menu, select HA Programming, HA Units [961].
2.
Select an HA unit (01-16).
3.
From the HA unit’s sub-menu, select On by Zone [#04].
4.
Enter up to two zone numbers.
70
iConnect
Installation Manual
12 Home Automation Programming
12.2.3. On by Arm
The On by Arm feature activates the HA unit when the system is armed using any of the arming methods. The amount
of time the HA unit is activated is determined by the Pulse Time – see p. 72, 12.2.8 Pulse Time. If the Pulse Time is
programmed as "Toggle", disarming the system switches the HA unit off.
To program the On by Arm feature:
1.
From the Programming menu, select HA Programming, HA Units [961].
2.
Select an HA unit (01-16).
3.
From the HA unit’s sub-menu, select On by Arm [#05].
4.
Select Enabled or Disabled.
12.2.4. On by Alarm
On by Alarm is a feature designed for use with X10 sirens. When an alarm occurs, the HA unit (i.e. siren) is activated
for the duration of the siren cutoff – see p. 42, 7.7.2 Siren Cut-Off. The X10 siren sounds a continuous pattern for
intrusion/panic alarms and a pulsed pattern for fire alarms.
To program the On by Alarm feature:
1.
From the Programming menu, select HA Programming, HA Units [961].
2.
Select an HA unit (01-16).
3.
From the HA unit’s sub-menu, select On by Alarm [#06].
4.
Select Enabled or Disabled.
If an HA unit is programmed to be activated by the On by Alarm feature, program all other
operation modes (On by Arm, Randomize, etc.) as disabled.
Do not program more than one HA unit to be activated by the On by Alarm feature. If more
than one siren is required, set all sirens with the same House and Unit code.
12.2.5. Keyfob Control
Each keyfob (EL-4714), offers control of up to two individual HA units. This programming option allows you to enable
or disable this feature per HA unit.
To program the keyfob control option for an HA unit:
1.
From the Programming menu, select HA Programming, HA Units [961].
2.
Select an HA unit (01-16).
3.
From the HA unit’s sub-menu, select KF Ctrl [#07].
4.
Select Enabled or Disabled.
12.2.6. Telephone Control
Via SMS or DTMF, you can send commands to the system in order to control various HA units. This option allows you
to enable or disable this feature for each HA unit.
To program the telephone control option for an HA unit:
1.
From the Programming menu, select HA Programming, HA Units [961].
2.
Select an HA unit (01-16).
3.
From the HA unit’s sub-menu, select TEL Ctrl [#08].
4.
Select Enabled or Disabled.
12.2.7. Randomize
When the system is fully armed between the hours 9:00pm and 6:00am, the Randomize feature turns HA units on and
off at random. This gives the impression that the house is occupied and acts as a deterrent against potential intruders.
To program an HA unit to be included in the Randomize feature:
1.
From the Programming menu, select HA Programming, HA Units [961].
2.
Select an HA unit (01-16).
3.
From the HA unit’s sub-menu, select Randomize [#09].
4.
Select Enabled or Disabled.
iConnect
Installation Manual
71
12 Home Automation Programming
12.2.8. Pulse Time
The Pulse Time determines the manner in which an HA unit responds to the On command. You can program each HA
unit switch on momentarily. This means that, on receiving the On command, the unit will be switched on for a
programmed amount of time. For example, you can program the hall light to switch on for 1 minute and automatically
switch itself off. Alternatively, the HA unit can be programmed to toggle on and off.
To program the Pulse Time for an HA unit:
1.
From the Programming menu, select HA Programming, HA Units [961].
2.
Select an HA unit (01-16).
3.
From the HA unit’s sub-menu, select Pulse Time [#10].
4.
Select 5 sec, 30 sec, 1 min, 2 min or Toggle.
12.2.9. Descriptor
You can assign a 16-character descriptor for each HA unit. These descriptors help the user to identify the various HA
units installed around the home.
To edit an HA unit descriptor:
1.
From the Programming menu, select HA Programming, HA Units [961].
2.
Select an HA unit (01-16).
3.
From the HA unit’s sub-menu, select Descriptor [#11].
4.
Edit the descriptor using the alphanumeric keypad.
12.3. House Code
The House code is part of the identification code of each HA unit. For the Home Automation features to function
correctly, the House code on each HA unit must be identical to the House code programmed in the system’s memory.
To program the system House code:
1.
From the Programming menu, select HA Programming, House Code [962].
2.
Using the arrow keys, select a House code from the options available (A-P).
12.4. HA Control
The HA Control option allows you to enable or disable all Home Automation features for the entire system.
To program the Home Automation setting:
1.
From the Programming menu, select System Options, HA Control [963].
2.
Select Enabled or Disabled.
PGM output is not affected by HA Control parameter. Remote activation of PGM is possible,
even when HA control is disabled, as long as the PGM output trigger is defined as
Telecontrol – see p. 49 9.7.1 Output Trigger.
72
iConnect
Installation Manual
13 System Initialization
13. System Initialization
The Initialization menu offers a number of options that enable you to reset the system. This menu is particularly useful
when re-installing a Control System at a new site. The Initialization function clears the entire system. This restores
programming defaults, clears the log, user codes and the transmitter register. Options are also available that enable you
to clear a specific section of the system’s memory separately.
13.1. Initialization
The Initialization function clears the entire system and resets factory defaults. If your system does not include multidefault and multi-language support, skip steps 2 and 3 of the following procedure.
To initialize the Control System:
1.
From the Programming menu, select Initialize, Init All [971]; the system prompts you for confirmation.
2.
For firmware versions that include multi-default and multi-language support, select the set of programming
defaults that you want to load.
3.
For firmware versions that include multi-default and multi-language support, select the required interface
language. Factory programming defaults are restored, the event log is cleared, ser codes and wireless
transmitters are deleted.
During system initialization, recorded vocal messages (Message Center and Home ID) are
not deleted.
13.2. Default Program Restore
Loading the system’s default program enables you to restore the factory-set programming defaults.
To load the default program:
• From the Programming menu, select Initialize, Load Defaults [972]; the system prompts you for
confirmation.
13.3. Clear User Codes
Clear User Codes deletes all programmed user codes and restores the default Master and Installer codes.
To clear user codes:
• From the Programming menu, select Initialize, Clear Users [973]; the system prompts you for confirmation.
13.4. Clear Wireless Transmitters
The Clear Wireless Transmitters function enables you to delete all registered transmitters at once.
To clear the transmitter register:
• From the Programming menu, select Initialize, Clear Wireless [974]; the system prompts you for
confirmation.
13.5. Find Modules
The Find Modules function runs a diagnostic test that identifies the modules that are connected to the system bus. With
this information, the system knows which add-on modules should be present, enabling supervision for those modules.
To run the Find Modules test:
1.
From the Programming menu, select Initialize, find Modules [975]; the system prompts you for confirmation.
2.
Press '√ʹ to confirm; the system begins to search for the connected modules. At the end of the search, the modules
that are present are displayed and the system asks if you want to save the displayed list.
If a connected module is not included in the list, check the wiring connections and run this
test again.
iConnect
Installation Manual
73
Appendix A: Menu Structure
Appendix A: Menu Structure
Legend:
Installer code
required
Master code required
74
iConnect
Installation Manual
Appendix A: Menu Structure
iConnect
Installation Manual
75
Appendix A: Menu Structure
76
iConnect
Installation Manual
Appendix A: Menu Structure
iConnect
Installation Manual
77
Appendix A: Menu Structure
78
iConnect
Installation Manual
Appendix A: Menu Structure
iConnect
Installation Manual
79
Appendix A: Menu Structure
80
iConnect
Installation Manual
Appendix B: Transmitter Installation
Appendix B: Transmitter Installation
PIR Detectors (EL-4755/EL-4755PI)
The EL-4755 and EL-4755PI are intelligent 2-Way wireless PIR camera detectors designed for use with the iConnect
Control System.
Each iConnect
detectors.
Control System (up-to-32-zone) can support up to eight PIR camera
All these detectors implement a feature to combat the problem of multiple transmissions, which drastically reduce the life
of the batteries. After each transmission, there is a four-minute delay during which further transmissions will not be sent.
When batteries need replacing, the detector sends a low battery indication to the Control System. The EL-4755PI is
designed for pet installations and provides good immunity to nuisance alarms caused by pets and animals.
Detectors that meet the EN-50131 standard, have a three-minute delay between
transmissions.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Tamper switch and mounting tab
Fastening screw hole
Mounting holes
Battery holders
Antenna
PIR Detector
Indicator LED
Camera Lens
IR LEDs
Figure B- 1: PIR Detector Outer Casing, Front & Back Views – EL-4755/4755PI
Figure B- 2: PIR Detector with Cover Removed – EL4755/4755PI
Consideration before Installation
• Select a location from which the pattern of the detector is most likely to be crossed by a burglar, should there
be a break in.
• Do not place bulky objects in front of the detector.
• Avoid a location that comes in direct contact with radiators, heating/cooling ducts or air conditioners.
• Do not place the detector in front of windows subject to direct sunlight or drafts.
iConnect
Installation Manual
81
Appendix B: Transmitter Installation
Pet Immunity Guidelines (EL-4755PI)
It is expected that the EL-4755PI will eliminate false alarms caused by:
• Animals up to 36kg/80lbs
• Several small rodents
• Random flying birds.
The weight of the animal should only be used as a guide, other factors such as the length
and color of fur also affect the level of immunity.
For maximum pet immunity the following guidelines are recommended:
• Mount the center of the detector at a height of 2.0m.
• Do not aim the detector at stairways that can be climbed by an animal.
• Avoid a location where an animal can come within 1.8m (6') of the detector by climbing on furniture, boxes
or other objects.
Registration Procedure
The EL-4755/4755PI must identify itself to the iConnect
1.
Control System as follows
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ
2.
Unscrew the casing back
3.
Insert the supplied batteries into their battery holders. The detector will send a transmission, which if successfully
received by the system will generate a confirmation sound. If no confirmation sound is heard, send another
transmission by pressing and releasing the tamper switch of the device.
4.
After the detector is successfully registered the display shows: Save? Press '√ʹ to confirm and continue entering
other parameters for the chosen device.
To delete a PIR detector from the system refer to the Quick Installer manual.
Parameter Setting Procedure
As a 2-Way detector, the EL-4755/4755PI parameters can be modified only from the iConnect
Control System.
Go to the main menu and select [9]>[1]>[1]>[11] (Programming > Devices > Zones > Sensor Par) and define the parameters
according to the following table:
Table B- 1: Parameter Settings (EL-4755/EL-4755PI)
Sensor Par.
Parameter
LED
PULSE
ENABLED/DISABLED
1, 2 – The pulse counter determines the amount of beams that need to
be crossed before the sensor will produce an alarm, with 1 being more
sensitive:
1–20 minutes (3) – The delay between reporting detections to the main
unit
VGA (640X480), QVGA (320X240), QVGA (160X120)
COLOR, B&W (Black and White)
HIGH, LOW (more/less distortion)
ENABLED, DISABLED
1–9; 1–5 VGA (3)
For Future Use
ALARM DELAY
CAMERA RESOLUTION
COLOR
COMPRESSION
FLASH
# OF PICTURES
PICTURE DELAY
USER MONITOR
ZONE ASSIGNMENT
0–480 MS (480)
ENABLE, DISABLE
00-00-00-000 – Movement detection in any of the up-to-four specified
zones triggers the camera to take a picture.
*Default in bold
Web Interface Access
Transmitted pictures are visible through the web interface:
1.
Access the supplied IP through your smart phone (iPhone) or web browser
2.
Input access credentials
3.
Click “Video” to view captured still pictures and configure settings.
82
iConnect
Installation Manual
Appendix B: Transmitter Installation
Installation Procedure
To install PIR detectors:
Before permanently mounting the detector, test the transmitter from the exact mounting
position. If necessary, improve the position of the transmitter. The recommended height is
2.2m (6.6 ft).
1.
If the unit is screwed together, unscrew the casing back.
2.
Knock out the mounting holes of the mounting bracket and attach it to the wall, as appropriate.
Figure B- 3: Mounting Screw Position
Figure B- 4: Rear Tamper Release
3.
To use the rear tamper switch, insert a screw into the rear tamper mounting hole located in the lower center of the
bracket. When the bracket is removed from the wall, the screw causes the tamper release to break away from
the bracket and the rear tamper switch is released
4.
Attach the screw provided in the detector kit to the bottom of the mounting bracket.
Operation Modes
Warm-up Time
The detector will need to warm up for the first 90 seconds after applying power.
Walk Test Mode
A walk test is performed in order to determine the lens coverage pattern of the detector. Walk Test mode cancels the
delay time between detections, enabling you to perform an efficient walk test.
To walk test the detector:
1.
Set the iConnect
2.
Walk across the scope of the detector according to the detection pattern selected.
3.
Confirm that the LED activates and deactivates accordingly. Wait for ten seconds after each detection before
continuing the test.
4.
After completing the walk test set the system to normal operation mode.
Control System to Walk test mode (Quick key 7>03>4).
To test the detector camera:
Control System to camera test mode (Quick key 7>03>5). Confirm with '√ʹ.
1.
Set the iConnect
2.
If more than one PIR camera zone is defined, select a defined zone and press '√ʹ.
3.
In the displayed: SNAPSHOTS, choose the number (1-9) of snapshots to be taken and press '√ʹ to transmit the
snapshots.
LED Indication
The LED indicator is lit every time a transmission is made. The LED can be enabled / disabled by programming.
Battery Replacement
In case of a low battery (2.5VDC or less), the detector low battery condition is reported to the system and low battery
message is displayed.
To replace the battery:
1.
Unscrew the casing back.
2.
Remove the spent batteries and replace them.
3.
Re-attach the casing front and remount unit.
iConnect
Installation Manual
83
Appendix B: Transmitter Installation
P
C
B
Figure B- 5: Lens Coverage – EL-4755
Figure B- 6: Lens Coverage – EL-4755PI
Figure B- 7: Camera Lens Coverage (Top View) – EL-4755/EL-4755PI
10m
10m
70°
2m
2.4m
70°
1.55m
1.85m
Figure B- 8: Camera Lens Coverage (Side View) –
EL-4755
Figure B- 9: Camera Lens Coverage (Side View) – EL4755PI
EL-4755/4755PI complies with EN-50131 2-2 Grade 2 Class II Power Supply Type C.
PIR Detectors (EL-4745/EL-4745PI)
The EL-4745 and EL-4745PI are intelligent 2-Way wireless PIR detectors designed for use with the iConnect
Control
System. All of these detectors implement a feature to combat the problem of multiple transmissions, which drastically
reduce the life of the batteries. After each transmission, there is a four-minute delay during which further transmissions
will not be sent. When batteries need replacing, the detector sends a low battery indication to the Control System.
Detectors that meet the EN-50131 standard, have a three-minute delay between transmissions.
The EL-4745PI is designed for installations prone to nuisance alarms caused by pets or small animals.
84
iConnect
Installation Manual
Appendix B: Transmitter Installation
1.
2.
3.
4.
5.
6.
7.
Antenna
LED
Battery compartment
Tamper switch
Pyro sensor
PCB Release tab
Optional Battery
compartment
Figure B- 10: PIR Detector with Cover Removed – EL-4745
1.
2.
3.
4.
5.
6.
Antenna
LED
Battery compartment
Tamper switch
Pyro sensor
PCB Release tab
Figure B- 11: PIR Detector with Cover Removed – EL4745PI
Considerations before Installation
• Select a location from which the pattern of the detector is most likely to be crossed by a burglar, should there
be a break in.
• Do not place bulky objects in front of the detector.
• Avoid a location which comes in direct contact with radiators, heating/cooling ducts, mirrors and air
conditioners.
• Do not place the detector in front of windows subject to direct sunlight or drafts.
Pet Immunity Guidelines (EL-4745PI)
It is expected that the EL-4745PI detector will eliminate false alarms caused by:
• Animals up to 36kg/80lb (EL-4745PI)
• Several small rodents
• Random flying birds
The weight of the animal should only be used as a guide, other factors such as the length
and color of fur also affect the level of immunity.
For maximum pet immunity the following guidelines are recommended:
• Mount the center of the unit at a height of 2.0m (6.5')
• Do not aim the detector at stairways that can be climbed by an animal.
• Avoid a location where an animal can come within 1.8m (6') of the detector by climbing on furniture, boxes
or other objects.
Registration Procedure
The EL-4745PI must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ
2.
Detach the mounting bracket from the detector.
3.
Open the battery compartment door.
4.
Remove the isolator that separates the battery from the contacts on the battery holder. The detector will send a
transmission. If the transmission is successfully received by the system it will play a confirmation sound. If no
confirmation sound is heard, send another transmission by pressing and releasing the tamper switch of the
device.
5.
After the detector is successfully registered the display shows: Save? Press '√ʹ to confirm and continue entering
other parameters for the chosen device.
iConnect
Installation Manual
85
Appendix B: Transmitter Installation
An additional battery can be placed inside the detector (EL-4745). To insert the additional
battery open the front cover and place the battery. Pay attention to the polarity.
Installation Procedure
To install PIR detectors:
Before permanently mounting the detector, test the transmitter from the exact mounting
position. If necessary, improve the position of the transmitter. The recommended height is
2.2m (6.6 ft).
1.
Knock out the mounting holes of the mounting bracket and attach it to the wall.
2.
To use the rear tamper switch, insert a screw into the rear tamper mounting hole located in the center of the
bracket. When the bracket is removed from the wall, the screw causes the tamper release to break away from
the bracket and the rear tamper switch is released
3.
Align the pins on the mounting bracket with the slots on the detector's base, attach the EL-4745PI to the bracket and
slide it down while gently pressing it to fit to its place.
4.
Attach the screw provided in the detector kit to the bottom of the mounting bracket.
Operation Modes
Warm-Up Time
The detector will need to warm up for the first 90 seconds after applying power.
Walk Test Mode
A walk test is performed in order to determine the lens coverage pattern of the detector. Walk Test mode cancels the
delay time between detections, enabling you to perform an efficient walk test.
To perform a Walk Test:
Control System to Walk test mode (Quick key [7034]).
1.
Set the iConnect
2.
Walk across the scope of the detector according to the detection pattern selected.
3.
Confirm that the LED activates and deactivates accordingly. Wait for ten seconds, after each detection, before
continuing the test.
4.
After completing the walk test set the system to normal operation mode.
LED Indication
The LED indicator is lit every time a transmission is made. The Led can be enabled / disabled by programming.
LED should only be disabled after successfully walk testing the detector.
Parameters Setting Procedure
As a 2-Way detector, the EL-4745PI parameters can be modified only from the iConnect
Control System.
In comparison to other detectors the EL 4745PI has dedicated parameters that can be modified under quick key 9>1>1>11
• LED Enable: On/Off (Default: On)
• Pulse count: The pulse counter determines the amount of beams that need to be crossed before the detector
will produce an alarm.
• Alarm Delay: The delay between reporting detections to the main unit.
Battery Replacement
In case of a low battery (2.5 VDC or less), the detector low battery condition is reported to the system and low battery
message is displayed.
To replace the battery:
Open the battery compartment door located on the back cover, replace the battery, and close the compartment door.
Attach the EL-4745PI to the bracket and slide it down while gently pressing it to fit to its place.
86
iConnect
Installation Manual
Appendix B: Transmitter Installation
Figure B- 12: Lens Coverage Diagrams EL-4745
Figure B- 13: Lens Coverage Diagrams EL-4745PI
EL-4745 complies with EN-50131 2-2 Grade 2 Class II Power Supply Type C
Dual Magnetic Contact/Universal Transmitter (EL-4601DZ)
The EL-4601DZ is a 2-Way wireless device that can be defined either as a magnetic contact, a universal transmitter or both
Control System. When batteries need replacing, the ELin combination. The EL4601DZ is for use with the iConnect
4601DZ sends a low battery indication to the Control System.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Magnet
Antenna
Battery Holder
LED Indicator
Reed switch
Tamper Switch
Location of Wiring Knockout
PCB Release Tab
Terminal Block
Figure B- 14: EL-4601DZ (Cover Off)
Registration Procedure
The EL-4601DZ must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ.
2.
Open the detector housing by inserting a small screwdriver at the bottom of the unit between the front and back
cover and twist the screwdriver to release the cover.
3.
Remove the divider separating the battery from the contacts on the battery holder. The detector will send a
transmission. If the transmission is successfully received by the system it will play a confirmation sound. If no
confirmation sound is heard send another transmission by pressing and releasing the tamper switch of the
device.
iConnect
Installation Manual
87
Appendix B: Transmitter Installation
Due to the occurrence of voltage delay in lithium batteries that have been in storage, the
batteries may initially appear to be dead. In this case, leave the unit in Test mode for a few
minutes until the battery voltage level is stabilized.
4.
As soon as 'Save?' appears press '√ʹ.
Parameter Settings
As a 2-Way detector, the EL-4601DZ parameters can be modified only from the iConnect
Control System.
The parameter settings can be defined as follows:
1.
Go to the main menu and select [9]>[1]>[1]>[11] (Programming > Devices > Zones>Sensor Par.)
2.
Select the Sensor Type (Magnetic, Universal or Magnetic + Universal)
3.
Define Second Zone (1-32) for dual Magnetic + Universal configuration.
By default the EL-4601DZ is registered as a Magnetic Contact. The Universal Transmitter
can function in the same zone or can be assigned to a separate zone. If assigned to a separate
zone any receiver already assigned to the selected zone will be deleted. For dual
configuration each zone should be configured exclusively.
4.
Press'√ʹ to confirm.
Installation Procedure
Once the detector has been registered mount the detector as follows:
Before permanently mounting the unit, test the transmitter from the exact mounting
position. If necessary, improve the position of the transmitter. The alarm is generated by
magnet removal at 24 (+/- 0.5) mm and is cleared by magnet approach at 22 (+/- 0.5) mm
1.
Open the detector housing.
2.
Remove the PCB by pressing the PCB release tab.
3.
Mount the back cover using two screws and replace the PCB. Use ISO 7050 (ST3.5 x 22) or similar countersunk
screws so that the screw head will not touch the PCB.
When handling the PCB, do not apply pressure on the antenna.
Figure B- 15: Mounting Screw Position
Figure B- 16: Rear Tamper Release
The upper screw is also used for back tamper. When the detector is removed from the wall,
the screw causes the tamper release to break away from the back cover and the rear tamper
switch is released.
4.
Knockout the wiring hole in the back cover.
5.
Thread the wires through the wiring hole.
6.
Connect the terminal block.
7.
Test the transmitter, making certain that the LED is lit during transmission.
8.
Open the magnet housing.
9.
Mount the back cover of the magnet using two screws.
Make sure that the guideline on the magnet is correctly aligned with the guideline on the
transmitter. Do not install the magnet further than 1cm from the transmitter.
10.
Test the transmitter, making certain that the LED is lit when opening the door/window and again when closing.
11.
Close the front covers of the transmitter and the magnet.
88
iConnect
Installation Manual
Appendix B: Transmitter Installation
Deleting the Dual Magnetic Contact/Universal Transmitter
To delete the EL-4601DZ from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones).
• Select a zone and press '√ʹ
2.
Press >12 > '√ʹ.
3.
Open the detector and take out the battery.
4.
Press the tamper switch. While the tamper switch is being pressed insert the battery.
5.
Within five seconds open the tamper and close it again.
For dual configuration (Magnetic + Universal) both magnetic and universal zones will be deleted.
EL-4601DZ complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
Universal Transmitter (EL-4602)
The EL-4602 is a 2-Way universal transmitter that includes a single output for use in a wide range of wireless
applications. When batteries need replacing, the EL-4602 sends a low battery indication to the Control System.
1.
2.
3.
4.
5.
6.
7.
Terminal Block
Antenna
Battery Holder
LED Indicator
Tamper Switch
Location of Wiring Knockout
PCB Release Tab
Figure B- 17: EL-4602 (Cover Off)
Registration Procedure
The EL-4602 must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ.
2.
Open the transmitter housing by inserting a small screwdriver at the bottom of the unit between the front and back
cover and twist the screwdriver to release the cover.
3.
Remove the divider separating the battery from the contacts on the battery holder. The transmitter will send a
transmission. If the transmission is successfully received by the system it will play a confirmation sound. If no
confirmation sound is heard send another transmission by pressing and releasing the tamper switch of the
device.
Due to the occurrence of voltage delay in lithium batteries that have been in storage, the
batteries may initially appear to be dead. In this case, leave the unit in Test mode for a few
minutes until the battery voltage level is stabilized
4.
As soon as 'Save?' appears press '√ʹ.
Installation Procedure
After the transmitter has been registered mount the transmitter as follows:
Before permanently mounting the unit, test the transmitter from the exact mounting
position. If necessary, improve the position of the transmitter.
iConnect
Installation Manual
89
Appendix B: Transmitter Installation
1.
Open the transmitter housing.
2.
Remove the PCB by pressing the PCB release tab.
When handling the PCB, do not apply pressure on the antenna
3.
Mount the back cover using two screws and replace the PCB. Use ISO 7050 (ST3.5 x 22) or similar countersunk
screws so that the screw head will not touch the PCB.
Figure B- 18: Mounting Screw Position
Figure B- 19: Rear Tamper Release
The upper screw is also used for back tamper. When the transmitter is removed from the
wall, the screw causes the tamper release to break away from the back cover and the rear
tamper switch is released.
4.
Knockout the wiring hole in the back cover.
5.
Thread the wires through the wiring hole.
6.
Connect the terminal block.
7.
Test the transmitter, making certain that the LED is lit during transmission.
8.
Close the front cover of the transmitter.
EL-4602 complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C.
Deleting a Universal Detector
To delete a Universal detector from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones).
• Select a zone and press '√ʹ
2.
Press >12 >√.
3.
Open the detector and take out the battery.
4.
Press the tamper switch. While the tamper switch is being pressed insert the battery.
5.
Within five seconds open the tamper and close it again.
Vibration Detector (EL-4607)
The EL-4607 is a 2-Way wireless vibration detector for use with the iConnect
1.
2.
3.
4.
5.
6.
Control System.
Antenna
Battery Holder
LED Indicator
Tamper Switch
Piezo Electric Sensor
PCB Release Tab
Figure B- 20: EL-4607 (Cover Off)
90
iConnect
Installation Manual
Appendix B: Transmitter Installation
Registration Procedure
The EL-4607 must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ.
2.
Open the detector housing.
3.
Remove the divider separating the battery from the contacts on the battery holder. The detector will send a
transmission. If the transmission is successfully received by the system it will play a confirmation sound. If no
confirmation sound is heard send another transmission by pressing and releasing the tamper switch of the
device.
Due to the occurrence of voltage delay in lithium batteries that have been in storage, the
batteries may initially appear to be dead. In this case, leave the unit in Test mode for a few
minutes until the battery voltage level is stabilized.
4.
As soon as 'Save?' appears press '√ʹ.
Parameter Settings
As a 2-Way detector, the EL-4607 parameters can be modified only from the iConnect
Control System.
The parameter settings can be defined as follows:
1.
Go to the main menu and select [9]>[1]>[1]>[11] (Programming > Devices > Zones>Sensor Par.)
2.
Select Sensitivity and define the parameter accordingly (1 – 100); 1 being the lowest, 100 the highest.
3.
Press'√ʹ to confirm.
Installation Procedure
After the detector has been registered, mount the unit as follows:
Before permanently mounting the unit, test the detector from the exact mounting position. If
necessary, relocate the detector to a better position.
1.
Open the detector housing.
2.
Remove the PCB by pressing the PCB release tab.
3.
Mount the back cover using two screws and replace the PCB. Use ISO 7050 (ST3.5 x 22) or similar countersunk
screws so that the screw head will not touch the PCB.
When handling the PCB, do not apply pressure on the antenna.
Figure B- 21: Mounting Screw Position
Figure B- 22: Rear Tamper Release
The upper screw is also used for back tamper. When the detector is removed from the wall,
the screw causes the tamper release to break away from the back cover and the rear tamper
switch is released.
4.
Test the detector, making certain that the LED is lit during transmission.
5.
Close the front cover of the detector.
Testing the Vibration Detector
Once you have mounted the detector, test the detector’s sensitivity, as follows:
1.
With the tamper switch open, strike the protected door or window at the furthest point away from the detector
with a screwdriver handle or cushioned tool; the LED color indicates the sensitivity level of the detector. Refer
to following table:
iConnect
Installation Manual
91
Appendix B: Transmitter Installation
Table B- 2: LED Sensitivity Level (EL-4607)
LED
Sensitivity Level
Red
Green
Orange
Under-sensitive indication
Normal sensitivity (recommended)
Over-sensitive indication
2.
If required, adjust the Sensitivity parameter.
3.
Repeat the sensitivity test until you achieve the required sensitivity level.
4.
After you have adjusted the Sensitivity parameter, repeat the test once more.
5.
Close the front cover of the detector.
Deleting a Vibration Detector
To delete a vibration detector from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones).
• Select a zone and press '√ʹ
2.
Press >12 >√.
3.
Open the detector and take out the battery.
4.
Press the tamper switch. While the tamper switch is being pressed insert the battery.
5.
Within five seconds open the tamper and close it again.
Smoke Detector (EL-4703)
The EL-4703 is a single station, photoelectric smoke detector with a built-in supervised wireless transmitter.
When sufficient smoke is detected, or the test feature is operated, the detector will sound its alarm horn and the
transmitter will send an ALARM message. The Alarm output in the receiver will remain activated until the alarm
condition clears.
The smoke alarm base lock discourages unauthorized removal of the smoke alarm by requiring a screwdriver to remove
the alarm from the base.
The smoke alarm provides the following signals to the control panel:
• Alarm
• Alarm restore
• Low battery
• Tamper
• Supervision
WARNINGS:
This smoke detector is designed for use in a single residential unit only, which means that it
should be used inside a single family home or apartment. It is not meant to be used in
lobbies, hallways, basements, or another apartment in multi-family buildings, unless there
are already working detectors in each family unit. Smoke detectors, placed in common areas
outside of the individual living unit, such as on porches or in hallways, may not provide
early warning to residents. In multi-family buildings, each family living unit should set up
its own detectors.
This detector is not to be used in non-residential buildings. Warehouses, industrial or
commercial buildings, and special purpose non-residential buildings require special fire
detection and alarm systems. This detector alone is not a suitable substitute for complete fire
detection systems for places where many people live or work, such as hotels or motels. The
same is true of dormitories, hospitals; nursing homes or group homes of any kind, even if
they were once single - family homes. Please refer NFPA 101, the Life Safety Code, NFPA71,
72A, 72B, 72C, 72D, and 72E for smoke detector requirements for fire protection in buildings
not defined as “households”.
92
iConnect
Installation Manual
Appendix B: Transmitter Installation
Selecting a Location
Smoke detectors should be installed in accordance with the NFPA Standard 74 (National Fire Protection Association,
Batterymarch Park, Quincy, MA 02169). For complete coverage in residential units, smoke detectors should be installed in
all rooms, halls, storage areas, basements, and attics in each family living unit. Minimum coverage is one detector on each
floor and one in each sleeping area and attics in each family living unit. Minimum coverage is one detector on each floor
and one in each sleeping area.
• Install a smoke detector in the hallway outside every separate bedroom area. Two detectors are required in
homes with two bedroom areas.
• Install a smoke detector on every floor of a multi-floor home or apartment.
• Install a minimum of two detectors in any household.
• Install a smoke detector inside every bedroom.
• Install smoke detectors at both ends of a bedroom hallway if the hallway is more than 40 feet (12 meters)
long.
• Install a smoke detector inside every room where one sleeps with the door partly or completely closed, since
smoke could be blocked by the closed door and a hallway alarm may not wake up the sleeper if the door is
closed.
• Install basement detectors at the bottom of the basement stairwell.
• Install second-floor detectors at the top of the first-to-second floor stairwell.
• Be sure no door or other obstruction blocks the path of smoke to the detector.
• Install additional detectors in your living room, dining room, family room, attic, utility and storage rooms.
• Install smoke detectors as close to the center of the ceiling as possible. If this is not practical, put the detector
on the ceiling, no closer than 4 inches (10 cm) from any wall or corner.
• If ceiling mounting is not possible and wall mounting is permitted by your local and state codes, put wallmounted detectors between 4 and 6 inches (10 ~ 15 cm) from the ceiling.
• If some of your rooms have sloped, peaked, or gabled ceilings, try to mount detectors 3 feet (0.9 meter)
measured horizontally from the highest point of the ceiling.
Figure B- 23: Locations for placing smoke detectors for
single residence with only one sleeping area
Figure B- 25: Location for placing
smoke detectors for a multi-floor
residence
iConnect
Installation Manual
Figure B- 24: Locations for placing smoke detectors for singlefloor residence with more than one sleeping area
Figure B- 26: Recommended best
and acceptable locations to mount
smoke detectors
Figure B- 27: Recommended location to
mount smoke detectors in rooms with
sloped, gabled, or peaked ceiling
93
Appendix B: Transmitter Installation
CAUTION:
(As required by the California State Fire Marshall)
“Early warning fire detection is best achieved by the installation of fire detection equipment
in all rooms and areas of the household as follows: (1) A smoke detector installed in each
separate sleeping area (in the vicinity, but outside of the bedrooms), and (2) Heat or smoke
detectors in the living rooms, dining rooms, bedrooms, kitchens, hallways, attics, furnace
rooms, closets, utility and, storage rooms, basements and attached garages.”
For your information, NFPA Standard 74, Section 2-4 reads as follows:
“2-4.1.1 Smoke detectors shall be installed outside of each separate sleeping area in the
immediate vicinity of the bedrooms and on each additional story of the family living unit
including basements and excluding crawl spaces and unfinished attics.
The provisions of 2-4.1.1 represent the minimum number of detectors required by this
standard. It is recommended that the householder consider the use of additional smoke
detectors for increased protection for those areas separated by a door from the areas
protected by the required smoke detectors under 2-4.1.1 above. The recommended
additional areas are living room, dining room, bedroom(s), kitchen, attic (finished or
unfinished), furnace rooms, utility room, basement, integral or attached garage, and
hallways not included in 2-4.1.1 above. However, the use of additional detectors remains the
option of the householder.” We recommend complete coverage and use of additional smoke
detectors.
Where to Install Your Smoke Detectors in Mobile Homes and RVs
Mobile homes and RVs built after about 1978 were designed and insulated to be energy-efficient. In mobile homes and
RVs built after 1978, smoke detectors should be installed as described above. Older mobile homes and RVs may have little
or no insulation compared to current standards. Outside walls and roofs are often made of non-insulated metal, which
can transfer thermal energy flow from outdoors. This makes the air right next to them hotter or colder than the rest of the
inside air. These layers of hotter or colder air can keep smoke from reaching a smoke detector. Thereby, install smoke
detectors in such units only on inside walls. Place them between 4 and 6 inches (10 ~ 15 cm) from the ceiling. If you are
not sure how much insulation is in your mobile home or RV, then install the detector on an inside wall. If the walls or
ceiling are unusually hot or cold, then install the detector on an inside wall. Install one detector as close to the sleeping
area as possible for minimum security, or install one detector in each room for security. Before you install any detector,
please read the following section on “Where not to install your smoke detectors”.
Where Not to Install Your Smoke Detectors
False alarms occur when smoke detectors are installed where they will not work properly. To avoid false alarms, do not
install smoke detectors in the following situations:
• Combustion particles are by-products of something burning. Do not install smoke detectors in or near areas
where combustion particles are present, such as kitchens with few windows or poor ventilation, garages
where there may be vehicle exhaust, near furnaces, hot water heaters and space heaters.
• Do not install smoke detectors less than 6 meters (20 feet) away from places where combustion particles are
normally present, like kitchens. If a 20-foot distance is not possible, e.g. in a mobile home, try to install the
detector as far away from the combustion particles as possible, preferably on the wall. To prevent false
alarms, provide good ventilation in such places.
Never try to avoid false alarms by disabling the detector.
• Do not mount smoke detectors in the path of fresh air intake. The flow of fresh air in and out can drive
smoke away from the smoke detector; thus reducing its efficiency.
• Near paint thinner fumes.
• In close proximity to an automobile exhaust pipe; this will damage the detector.
• In damp or very humid areas or near bathrooms with showers. Moisture in humid air can enter the sensing
chamber, then turns into droplets upon cooling, which can cause false alarms. Install smoke detectors at
least 3 meters (10 feet) away from bathrooms.
• In very cold or very hot areas, including unheated buildings or outdoor rooms. If the temperature goes
above or below the operating range of smoke detector, it will not work properly. The temperature range for
your smoke detector is 4°C to 38°C (40°F to 100°F).
94
iConnect
Installation Manual
Appendix B: Transmitter Installation
• In very dusty or dirty areas, dirt and dust can build up on the detector's sensing chamber, to make it overly
sensitive.
• Additionally, dust or dirt can block openings to the sensing chamber and keep the detector from sensing
smoke.
• Near fresh air vents or very drafty areas like air conditioners, heaters or fans. Fresh air vents and drafts can
drive smoke away from smoke detectors.
• Dead air spaces are often at the top of a peaked roof, or in the corners between ceilings and walls. Dead air
may prevent smoke from reaching a detector.
• In insect-infested areas. If insects enter a detector's sensing chamber, they may cause a false alarm. Where
bugs are a problem, get rid of them before putting up a detector.
• Near fluorescent lights, electrical "noise" from fluorescent lights may cause false alarms. Install smoke
detectors at least 1.5 meters (5 feet) from such lights.
Air Return
Air Entry
Bath
Stove
Bedroom
Kitchen
Living
Room
Bedroom
Correct Location
Incorrect Location
Figure B- 28: Recommended Smoke Detector Locations
The smoke detector is to be mounted on the ceiling or on the wall, if necessary. Since the smoke detector is a singlestation type, it cannot be linked to other detectors.
Do not connect the smoke detectors to any other alarm or auxiliary device. Connecting
anything else to this detector will prevent it from working properly.
Read the “Where to Install Your Smoke Detector” and “Where Not to Install Your Smoke Detectors” sections in this
Manual before installing. To install the detector, perform the following steps.
Registration Procedure
The EL-4703 must identify itself to the EL wireless system receivers as follows:
1.
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ.
2.
Open the detector housing.
3.
Insert the batteries into compartment. The detector will send a transmission. If the transmission is successfully
received by the system it will play a confirmation sound. If no confirmation sound is heard send another
transmission by pressing and releasing the tamper switch of the device.
Due to the occurrence of voltage delay in lithium batteries that have been in storage, the
batteries may initially appear to be dead. In this case, leave the unit in Test mode for a few
minutes until the battery voltage level is stabilized.
4.
As soon as 'Save?' appears, press '√ʹ
Installation Procedure
1.
Select the installation location.
2.
Remove locking pin securing the mounting bracket to the unit.
3.
Remove the mounting bracket from the unit by rotating it counterclockwise.
iConnect
Installation Manual
95
Appendix B: Transmitter Installation
4.
Use the bracket as a template for marking the mounting holes
5.
Using an appropriate drill, drill two holes at the marks and insert anchors.
6.
Using screws (supplied) attach the bracket to the wall.
7.
Line up the side slot of the bracket and the detector. Push the detector onto the mounting bracket and turn it
clockwise to fix it into place.
8.
Insert the locking pin in order to secure the mounting bracket to the detector.
9.
Pull the detector outward to make sure it is securely attached to the mounting bracket.
Locking Pin
Battery Compartment
Detector
Bracket
Tamper
Screws
Figure B- 29: Smoke Detector Installation
Figure B- 30: Batteries Compartment/Tamper
This detector is not suitable for installation in a hazardous location, as defined in the
national electrical code. Do not use detector in an outlet controlled by a wall switch.
Deleting a Smoke Detector
To delete a smoke detector from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones).
• Select a zone and press '√ʹ
2.
Press >12 > '√ʹ.
3.
Open the detector and take out the battery.
4.
Press the tamper switch. While the tamper switch is being pressed insert the battery. Within five seconds open the
tamper and close it again
Testing Your Smoke Detector
To be sure that detector is working correctly test the detector weekly by performing the following procedure:
Use your finger to firmly press the test button. If the detector is functioning correctly, the alarm horn sounds. To stop the
alarm horn, press the test button again. If the detector fails to test properly, have it repaired or replaced immediately.
If the alarm horn begins to beep once every 35 seconds, it means that the detector’s batteries are weak. Replace the
batteries immediately. Keep fresh batteries on hand for this purpose.
Detector
Buzzer
Openings
Test / Silence
Button
LED Indicator (Red)
Figure B- 31: Testing the Smoke Detector
Cooking smoke or a dusty furnace (sometimes called “friendly fires”) can cause the alarm to
sound. If this happens, open a window or fan the air to remove the smoke or dust. The
alarm will turn off as soon as the air is completely clear. Do not disconnect the batteries
from the detector. This will cancel your protection from fire.
96
iConnect
Installation Manual
Appendix B: Transmitter Installation
Red Indicator
When the red LED indicator flashes once in 30 seconds, it indicates the detector is under normal operation. When the red
LED flashes very frequently and an audible alarm sounds simultaneously, it indicates that the detector senses smoke.
The red LED behaves according to one of the following set modes:
Mode 1: The red LED indicator will not reset automatically at the end of an alarm event.
This means that after the smoke chamber is cleared, the audible alarm will stop
automatically, but the red LED indicator will continue to flash, until it is manually restored
by the user. To restore – press the test button for 2-3 seconds, the LED will stop flashing.
Mode 2 (Default): The red LED will reset automatically at the end of an alarm event.
The user can check to which mode the detector is defined and switch between modes.
•
To check the mode, press the Test button. The red LED will light up. If the red
LED lights up continuously the detector is in Mode 1. If the red LED is blinking
the detector is in Mode 2.
•
To switch from one mode to another, press the Test button for 8 seconds. The
buzzer will sound and the red LED will change its behavior either from a
continuous light to a blinking light or from a blinking light to a continuous light.
Taking Care of Your Smoke Detector
To keep your detector in good working condition, you must test the detector weekly, according to the “Testing Your
Smoke Detector” section.
Cleaning the Smoke Detector
1.
Clean the housing with a dry or damp cloth to remove dust and dirt. If necessary, open the smoke chamber and
clean the interior of the detector.
2.
Remove the detector from the detector base.
3.
Remove the batteries.
4.
Using a flat screwdriver release the smoke detector cover.
5.
Using a flat screwdriver lift the smoke chamber housing slightly.
6.
Use a fine paintbrush to remove dirt from the chamber.
7.
After cleaning, close the smoke chamber, fix the housing and remount the detector on the ceiling.
Do not forget to change the batteries!
Battery Replacement
Replace the detector batteries once a year or immediately when the low battery “beep” signal sounds once every 35
seconds. The low-battery "beep" should last at least 30 days before the batteries die out completely.
If false alarms keep coming from the detector, you should check whether the detector’s
location is adequate. Refer to section “WHERE TO INSTALL SMOKE DETECTORS.” Have
your detector moved if it is not located properly. Clean the detector as described above.
iConnect
Installation Manual
97
Appendix B: Transmitter Installation
WARNINGS! LIMITATIONS OF SMOKE ALARMS
Wireless smoke alarms are very reliable, but may not work under all conditions. No fire
alarm provides total protection of life or property. Smoke alarms are not a substitute for life
insurance.
Smoke alarms require a source of power to work.
This smoke alarm will not operate and the alarm will not sound if batteries are dead or not
installed properly.
Smoke alarms may not be heard. A sound sleeper or someone who has taken drugs or
alcohol may not awaken if the alarm is installed outside a bedroom. Closed or partially
closed doors and distance can block sound. This alarm is not designed for the hearing
impaired.
Smoke alarms may not always activate and provide warning early enough. Smoke alarms
only activate when enough smoke reaches the alarm. If a fire starts in a chimney, wall, roof,
on the other side of closed doors, or on a different level of the property enough smoke may
not reach the alarm for it to alarm.
Smoke alarms are a significant help in reducing loss, injury and even death. However, no
matter how good a detection device is, nothing works perfectly under every circumstance
and we must warn you that you cannot expect a smoke alarm to ensure that you will never
suffer any damage or injury.
Smoke detectors are not to be used with detector guards unless the combination has been
evaluated and found suitable for that purpose
Keyfobs (EL-4714)
The EL-4714 is a keyfob transmitter designed for use with the iConnect
Control System. The EL-4714 is a four-button
keyfob transmitter that offers a number of functions including arm, disarm and SOS Panic.
Figure B- 32: EL-4714
Figure B- 33: Opening the EL-4714’s Casing
Keys Operation and LED Indication
Table B-3: Keys Operation (EL-4714)
Key
Table B-4: LED Indication (EL-4714)
Operation
LED
Indication
Full Arm
Green:
Operation successful
Disarm
Flashing green for 4 seconds:
Operation fail
Part Arm, HA/PGM
Flashing Red for 4 seconds :
Low battery
Perimeter Arm, HA/PGM
Flashing amber for 4 seconds:
Out of range
Panic alarm (Press and hold down)
Green:
Operation successful
:
:
:
/
+
98
:
:
iConnect
Installation Manual
Appendix B: Transmitter Installation
Registration Procedure
The keyfob must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[2] (Programming > Devices > Keyfobs)
• Select a Keyfob (1-19) and press '√ʹ.
2.
Press one of the buttons on the Keyfob, making sure that the Keyfob’s green LED lights up when the button is
pressed.
3.
As soon as 'Save?' appears press '√ʹ.
A flashing red LED indicates a communication problem between the Keyfob and the system.
During registration, maintain a minimum 1 meter distance between the keyfob and panel.
Deleting a Keyfob
To delete a Keyfob from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[2] (Programming > Devices > Keyfobs).
• Select a Keyfob (1-19) and press '√ʹ
2.
Press >6 > '√ʹ.
3.
Press
4.
Press
+
for two seconds until the red led stops flashing
+
for two seconds until the red led stops flashing.
Battery Replacement
If the LED blinks during transmissions, this indicates that the battery is low and need replacing.
Batteries must be replaced within seven days of receiving a low battery indication. The
estimated battery life is 2 years (avg. 4 activations per day).
To replace the battery:
1.
Insert a small screwdriver into the pry-off slot. Carefully twist the screwdriver to separate the front and back of the
casing.
2.
Observing correct polarity, replace the battery.
3.
Close the casing making sure that the front and back click shut.
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
EL-4714 complies with EN-50131 Grade 2 Class II Power Supply Type C.
Keyfobs (EL-4711M/P)
The EL-4711M/P is a keyfob transmitters designed for use with the iConnect
Control System. The EL-4711M/P is a onebutton transmitter that generates a Medical/Panic alarm when pressed. The transmitter is water resistant and can be worn
around the neck. Its large button makes it ideal for elderly or sight-impaired users.
Figure B- 34: EL-4711M/P
iConnect
Installation Manual
Figure B- 35: Inserting the Cord (EL-4711M/P)
99
Appendix B: Transmitter Installation
LED Indication
Table B-5: LED Indication (EL-4714)
LED
Indication
Red (fast flash for 4 seconds)
Green
Amber
Outgoing transmission.
Operation successful
Low battery
Registration Procedure
The keyfob must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[2] (Programming > Devices > Keyfobs)
• Select a Keyfob and press '√ʹ.
2.
Press one of the buttons on the Keyfob, making sure that the Keyfob’s green LED lights up when the button is
pressed.
3.
As soon as 'Save?' appears press '√ʹ.
A flashing red LED indicates a communication problem between the Keyfob and the system.
During registration, maintain a minimum 1 meter distance between the keyfob and panel.
Deleting a Keyfob
To delete a Keyfob from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[2] (Programming > Devices > Keyfobs).
• Select a Keyfob (1-19) and press '√ʹ
2.
Press >6 > '√ʹ.
3.
Press and hold the Keyfob button for at least eight seconds. The initial red LED flashing indicates the Keyfob is
attempting to contact the system. After the flashing stops, a red/green flashing LED begins and when it stops,
the keyfob unregistration has succeeded.
Battery Replacement
If the LED blinks during transmissions, this indicates that the battery is low and need replacing.
Batteries must be replaced within seven days of receiving a low battery indication. The
estimated battery life is 2 years (avg. 4 activations per day).
To replace the battery:
1.
Insert a small screwdriver into the pry-off slot. Carefully twist the screwdriver to separate the front and back of the
casing (1-2).
2.
Observing correct polarity, replace the battery (3-4).
3.
Close the casing making sure that the front and back click shut (5).
Figure B- 36: Replacing the EL-4714’s batteries
100
iConnect
Installation Manual
Appendix B: Transmitter Installation
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
EL-4714M/P complies with EN-50131 Grade 2 Class II Power Supply Type C.
Wireless LCD Keypad (EL-4727)
The EL-4727 is a 2-Way wireless keypad with LCD display used to remotely program and operate the
Control System front panel.
The keypad's functionality is identical to the keys on the iConnect
Control System.
Programming mode can be established either from a keypad or from the main panel, but not
simultaneously.
1.
2.
3.
4.
5.
6.
Speaker
LCD Display
Arming Keys
Keypad
Microphone (optional)
System Status LEDs
Figure B- 37: Keypad front layout
Figure B- 38: Keypad back layout
Figure B- 39: Keypad mounting bracket
LED Indication
Table B-6: LED Indication (EL-4727)
OK LED:
LED:
Off:
Green:
Flashing red:
iConnect
Installation Manual
System disarmed
System armed
Alarm
Green:
Yellow:
Flashing green:
Flashing yellow:
Power OK
System trouble
Open zone
(Slow) Low battery, (Fast) AC loss
101
Appendix B: Transmitter Installation
Registration Procedure
The EL-4727 keypad must identify itself to the system receiver. This is done by registering the keypad to the iConnect
Control System as follows:
1.
Release the mounting bracket.
2.
Open the battery compartment and insert the batteries. Pay attention to the correct polarity.
3.
Set the system to registration mode
• Go to the main menu and select [9]>[1]>[3] (Programming > Devices > Keypads)
• Select a keypad (1-4)
4.
Press the keypad's tamper switch.
5.
As soon as 'Save?' appears on the Control System’s LCD screen, press '√ʹ
Installation Procedure
After the keypad has been registered to the system mount the keypad on the wall using the supplied mounting bracket.
1. Before mounting the keypad test the keypad communication with the system. To do so,
try to arm the system using one of the arming buttons on the wireless keypad.
2. Minimum mounting distance between the wireless keypad and the panel is 1.5m.
To mount the keypad:
1.
Release the mounting bracket
2.
Attach the mounting bracket to the wall using the supplied screws.
3.
Attach the wireless keypad to the mounting bracket by sliding it down.
4.
If required attach the housing screw at the bottom of the front cover.
Deleting a Keypad
To delete a wireless keypad from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[3] (Programming > Devices > Keypads).
• Select keypad (1-4) > '√ʹ
2.
Press >'√ʹ.
3.
Take out the keypad batteries.
4.
While the back tamper switch is being pressed insert the batteries.
5.
Within five seconds open the tamper and close it once again
Replacing Batteries
When the battery needs to be replaced the yellow OK LED will flash.
To replace the battery:
1.
Remove the keypad from the wall.
2.
Open the battery compartment.
3.
Pull out the battery and replace it with a new one. Pay attention to the polarity when inserting the new batteries
4.
Close the battery compartment, and place the keypad back to its place
Gas Leak Detector (EL-4762)
The EL-4762 is a 2-Way Wireless Gas Leak Detector used to detect mixtures of air and combustible gases (Natural Gas,
Methane, Propane and Butane). Upon detecting the presence of gas, the unit emits an alarm and notifies the control panel.
102
iConnect
Installation Manual
Appendix B: Transmitter Installation
Selecting a Location
The 2-Way Wireless Gas Leak Detector will function effectively if installed in the correct location. Consider the following
before mounting the gas alarm:
• Methane (Natural) Gas: Methane is lighter than air, therefore the greatest concentration of gas is found right
below the ceiling, and therefore the Wireless Gas Leak Detector should be installed on the wall,
approximately 30 cm (12”) below the ceiling.
• Butane Gas: Propane and Butane are heavier than air, therefore the greatest concentration of gas is found
right above the floor level. The Wireless Gas Leak Detector should therefore be installed about 30cm (12”)
above the floor. Do not mount in a location where the gas alarm could be damaged by dirt, liquids, etc.
Do not install the detector on the ceiling or on the floor.
Figure B- 40: Gas leak detector installation location
• Install the detector in close proximity to every gas-operated appliance.
Do not:
• Install the gas detector directly on any gas appliance.
• Install the gas detector in sealed or closed compartments or in an area where a wall or a closed door can
obstructs the flow of gas to the gas alarm.
• Install the gas detector in locations where fans, open doors, open windows etc. may prevent gas from
reaching the detector.
• Install the gas detector in any room where aerosols or ammonia are used (e.g. bathrooms).
Installation Procedure
1.
Remove the mounting bracket from your unit according to the illustrations below.
2.
1
2
3
Figure B- 41: Gas leak detector installation procedure (#1)
Figure B- 42: Gas leak detector installation procedure
(#2)
3.
Hold the Mounting bracket against the wall as a template and mark the locations for the 2 mounting holes.
4.
Using a 3/16-inch (5 mm) drill bit, drill two holes at the marks and insert wall plugs.
5.
Secure the mounting bracket to the wall.
6.
Line up the side slot of the bracket and the detector. Push the detector onto the mounting bracket and fix it. Pull the
detector outwards to make sure that it is securely attached to the mounting bracket.
7.
Connect the detector power cable to the wall power outlet.
iConnect
Installation Manual
103
Appendix B: Transmitter Installation
Registration Procedure
The EL-4762 must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ
2.
Ensure that the detector power cable is plugged into the wall power outlet. (Wait 3 minutes for the power-on
process to complete)
3.
Press the TEST button for 3 seconds to send a transmission. If the transmission is successfully received by the
system it will play a confirmation sound. If no confirmation sound is heard, repeat this step.
4.
After the detector is successfully registered the display shows: Save? Press '√ʹ to confirm.
5.
TEST/HUSH
POWER
SERVICE ALARM
ALARM VENT
SENSOR VENT
Figure B- 43: Gas leak detector registration procedure
LED & Buzzer Indication
Table B-7: LED & Buzzer Indication (EL-4762)
LED
LED Status
Green (Power)
Flashing (for 4
minutes)
On
RED (Alarm)
Flashing
Orange
(service)
On
Buzzer
Meaning
Warm up (the status between Power -Up
and Normal operation)
Normal Condition (Power On)
Sequential Alarm
Sound
Alarm
Malfunction/ detector interruption
Testing the Detector
To test the detector (do not test when detector is at warm up mode), press the Test Button.
•The red and orange LED's will flash and a sound will be heard
Muting the Detector
You can partially mute the detector in an event of alarm by pressing the Test Button. The Red LED will continue to flash
and a short sound will be heard every 16 seconds.
Detector Malfunctioning
A malfunctioning unit is indicated by beep-sounding on and off sequentially, i.e., beeping for 3 seconds with 3 seconds
delay between two beeps. If this occurs, unplug the detector from the power source for 10 seconds and then plug the unit
again. Should the unit beep intermittently, DO NOT use this detector. Send the malfunctioning unit for servicing.
Taking Care of the Detector
You have to maintain the detector frequently to ensure it working properly. Few tips are provided for you to take care of
your detector:
1.
Use a vacuum cleaner to clean the air vents occasionally to keep them free of dust.
2.
Push the Test button on your detector to test its operating function once every week.
104
iConnect
Installation Manual
Appendix B: Transmitter Installation
Actions to take when Alarm Sounding
In case of harmful levels of gas being detected, your detector will go into a continuous full alarm. Try to take the
following necessary actions immediately or evacuate the building:
• Widely open doors and windows
• Disconnect electrical appliances
• Avoid open fire
• Repair the gas leak by a professional gas repairer
Actions to take after the Problem Is Corrected
Once the problem about the gas presence in the premises has been corrected, the alarm of the detector should be off. After
waiting for 10 minutes, push the Test button to test the detector so that you can make sure that the detector is working
properly again.
Carbon Monoxide Detector (EL-4764)
The EL-4764 is a 2-Way Wireless Carbon Monoxide Detector (CO) used to detect the buildup of Carbon Monoxide. Upon
detecting the CO gas, the unit emits an alarm and notifies the control panel.
Things you should know about Carbon Monoxide
Carbon monoxide, also known as "CO" by the chemical form, is considered to be a highly dangerous poisonous gas,
because it is colorless, odorless, tasteless and very toxic. In general, biochemistry phenomena have shown that the
presence of CO gas inhibits the blood's capacity to transport oxygen throughout the body, which can eventually lead to
brain damage.
In any closed space (home, office, recreational vehicle or boat) even a small accumulation of CO gas can be quite
dangerous.
Although many products of combustion can cause discomfort and adverse health effects, it is CO gas which presents the
greatest threat to life.
Carbon monoxide is produced by the incomplete combustion of fuels such as natural gas, propane, heating oil, kerosene,
coal, charcoal, gasoline, or wood. The incomplete combustion of fuel can occur in any device which depends on burning
for energy or heat such as furnaces, boilers, room heaters, hot water heaters, stoves, grills, and in any gasoline powered
vehicle or engine (e.g. generator set, lawnmower). Tobacco smoke also adds CO to the air you breathe.
When properly installed and maintained, your natural gas furnace and hot water heater do not pollute your air space
with CO. Natural gas is known as a "clean burning" fuel because under correct operating conditions, the combustion
products are water vapor and carbon dioxide (CO2), which is not toxic. The products of combustion are exhausted from
furnaces and water heaters to the outside by means of a fuel duct or chimney.
Correct operation of any burning equipment requires two key conditions:
• An adequate supply of air for complete combustion.
• Proper venting of the products of combustion from the furnace through the chimney, vent or duct to the
outside.
Typical carbon monoxide gas problems are summarized here:
• Equipment problems, due to defects, poor maintenance, damaged and cracked heat exchangers
• Collapsed or blocked chimneys or flues, dislodged, disconnected or damaged vents
• Downdraft in chimneys or flues. This can be caused by very long or circuitous flue runs, improper location
of flue exhaust or wind conditions
• Improper installation or operation of equipment, chimney or vents
• Air tightness of house envelop/inadequate combustion of air
• Inadequate exhaust of space heaters or appliances
• Exhaust ventilation/fireplace competing for air supply
Potential sources of carbon monoxide in your home or office include clogged chimney, wood stove, wood or gas
fireplace, automobile and garage, gas water heater, gas appliance, gas or kerosene heater, gas or oil furnace and cigarette
smoke.
iConnect
Installation Manual
105
Appendix B: Transmitter Installation
Selecting a Location
Since CO gas moves freely in the air, the suggested location is in or as near as possible to sleeping areas of the home, 30
cm (12 inch) below the ceiling . For maximum protection, a CO detector should be located outside the primary sleeping
areas or on each level of your home.
BEDROOM
BEDROOM
GROUND
FLOOR
BEDROOM
KITCHEN
GARAGE
BASEMENT
CARBON MONOXIDE DETECTOR
Figure B- 44: Carbon Monoxide detector installation location
This device is not suitable for installation in a hazardous location, as defined by the US
National Electrical Code.
Do not place the detector in the following areas:
• Where the temperature may drop below 4°C (39°F) or exceed 38°C (100°F).
• Near paint thinner fumes
• Within 1.5 meter (5 feet) of open flame appliances such as furnaces, stoves and fireplaces
• In exhaust streams from gas engines, vents, flues or chimneys
• Do not place in proximity to an automobile exhaust pipe; this will damage the detector
Installation Procedure
1.
Remove the mounting bracket from your unit according to the illustrations below.
1
2
3
+
-
Figure B- 45: CO2 detector installation procedure
(#1)
Figure B- 46: CO2 detector
installation procedure (#2)
Figure B- 47: CO2 detector
installation procedure (#3)
2.
Hold the Mounting bracket against the wall as a template and mark the locations for the 2 mounting holes.
3.
Using a 5 mm (3/16-inch) drill bit, drill two holes at the marks and insert wall plugs.
4.
Secure the mounting bracket to the wall.
5.
Open the battery cover by pushing down on the battery snaps.
6.
Insert the batteries (supplied) into the battery compartment. Pay attention to the correct battery polarity (+) (-) and
close the battery compartment
7.
Line up the side slot of the bracket and the detector. Push the detector onto the mounting bracket until a click is
heard.
8.
Pull the detector outwards to make sure that it is securely attached to the mounting bracket.
106
iConnect
Installation Manual
Appendix B: Transmitter Installation
Registration Procedure
The EL-4764 must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ
2.
Ensure batteries are in place (as per Installation instructions above). The detector will send a transmission. If the
transmission is successfully received by the system it will play a confirmation sound. If no confirmation sound
is heard, send another transmission by pressing and releasing the tamper switch of the device.
3.
After the detector is successfully registered the display shows: Save? Press '√ʹ to confirm.
TEST/HUSH
POWER
SERVICE ALARM
ALARM VENT
SENSOR VENT
Figure B- 48: CO2 detector registration procedure
LED & Buzzer Indication
Table B-8: LED & Buzzer Indication (EL-4764)
Led Color
LED Status
Green (Power)
RED (Alarm)
Orange (service)
Flashing On and Off every 30
seconds
Flashing
Flashing On and Off
All LED's
Flashing
Buzzer
Meaning
Normal condition
Sequential Alarm Sound
Sequential Alarm Sound
3 beeps for a period of 3
seconds
Alarm
Internal self test fail service required
Test mode
Due to the occurrence of voltage delay in lithium batteries that have been in storage, the
batteries may initially appear to be dead. In this case, leave the unit in Test mode for a few
minutes until the battery voltage level is stabilized.
Testing And Resetting Your Detector
A green power light indicates that power is supplied. To test the detector, press the Test button. The detector will beep
intermittently and the three LEDs will flash. Release the Test button. The beep and the three LEDs will stop and the green
LED remains on or flashes every 60 seconds.
Muting Your Detector
You can partially mute the detector in an event of alarm by pressing the Test Button. The Red LED will continue to flash
and a short beep will be heard every 16 seconds.
Detector Malfunctioning
A malfunctioning unit is indicated by beep-sounding on and off sequentially, i.e., beeping for 3 seconds with 3 seconds
delay between two beeps. If this occurs, remove the batteries from the unit for 10 seconds and then install them again.
Should the unit again beep intermittently, DO NOT use this detector. Send the malfunctioning unit to the manufacturer
for servicing.
Taking Care Of Your Detector
You have to maintain the detector to ensure proper operation:
1.
Use a vacuum cleaner to clean the air vents occasionally to keep them free of dust.
2.
Press the Test button on your detector to test its operation once every week.
iConnect
Installation Manual
107
Appendix B: Transmitter Installation
Actions to Take When Alarm Sounding
In case of harmful levels of CO gas being detected, your detector will go into a continuous full alarm. Try to take the
following necessary actions immediately:
• If there is anyone experiencing the effects of carbon monoxide poisoning such as headache, dizziness, nausea
or other flu-like symptoms, call your fire department or emergency service department right away. You
should evacuate all the people in the premises immediately. Do a head count to check that everybody is
present.
• Do not re-enter the premises until the problem has been corrected and the CO gas has been dispersed out
and a safe level is reached.
• If no symptoms exist, immediately ventilate the home by opening windows and doors. Turn off fuel burning
appliances and call a qualified technician or your utility company to inspect and repair your problem before
restarting appliances.
•
WARNING
Normally an activation of the detector indicates the presence of CO gas. However, the CO
gas can be extremely fatal, if it is not detected. The source of the CO gas may come from
several possible situations, please refer to the list of sources of carbon monoxide in the
beginning of this section.
CAUTION
This detector will only indicate the presence of CO gas at the detector. However, you have
to be aware that the CO gas may be present in other areas in the premises.
Actions to Take After The Problem is Corrected
Once the problem of the CO gas presence in the premises has been corrected, the detector alarm should be off. After
waiting for 10 minutes, push the Test button to test the detector, and by that, being confident that the detector is working
properly again.
Technical Information
The Carbon Monoxide Detector is engineered to be able to provide alarm sounds based on the UL standards due to
various exposure times at different level of carbon monoxide concentrations.
According to the Underwriters Laboratories Inc. the carbon monoxide concentrations and exposure time standards for the
alarms have been established and specified below:
A full alarm is activated under the following conditions:
• Between 60 and 90 minutes at exposures of 70 ppm
• Between 10 and 30 minutes at exposures of 150 ppm
• Between 4 and 10 minutes at exposures of 400 ppm
WARNING AND LIMITATION
This detector may not alarm at low carbon monoxide levels. The Occupational Safety and
Health Association (OSHA) has established that continuous exposure levels of 30 ppm
should not be exceeded in an 8 hours period. Individuals with a medical problem may
consider more sensitive detection devices.
The CO gas detector is not suitable as a smoke or fire detector. This detector is not suitable
to install in a hazardous location, as defined in the National Electrical Code.
This detector will not work without power. EL's Carbon Monoxide Detector will not work if
the batteries are removed for any reason. Additionally, carbon monoxide must reach the
detector for the proper performance of CO gas detection.
Carbon monoxide detectors may wear out because they contain electronic parts that fail at
any time (see the section "Testing Your Detector").
108
iConnect
Installation Manual
Appendix B: Transmitter Installation
Flood Detector (EL-4761)
The EL-4761 is a 2-Way flood detector for use with the iConnect
Control System. The wireless flood detector is a fully
supervised detector used to detect the presence of water-based liquids at any desired location, such as basements or water
tanks. The detector is comprised from 2 parts: Wireless transmitter and flood detector which are connected by 2.4m cable.
In the event of flooding or leakage, the EL-4761 notifies the control System after detecting the presence of water for a
period of at least 20 seconds.
1.
Terminal Block
2.
Antenna
3.
Battery Holder
4.
LED Indicator
5.
Tamper Switch
6.
Location of Wiring Knockout
7.
PCB Release Tab
Figure B- 49: EL-4761 (Cover Off)
Registration Procedure
The EL-4761 must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones)
• Select a zone and press '√ʹ.
2.
Open the transmitter housing.
3.
Remove the divider separating the battery from the contacts on the battery holder. The transmitter will send a
transmission. If the transmission is successfully received by the system it will play a confirmation sound. If no
confirmation sound is heard send another transmission by pressing and releasing the tamper switch of the
device.
Due to the occurrence of voltage delay in lithium batteries that have been in storage, the
batteries may initially appear to be dead. In this case, leave the unit in Test mode for a few
minutes until the battery voltage level is stabilized
4.
As soon as 'Save?' appears press '√ʹ.
Flood Detector Mounting Location
The flood detector should be placed in a position where water will accumulate rapidly in the event of flooding.
After selecting the mounting location:
1.
Attach the flood detector in horizontal position near the floor with the 2 pins facing downwards using the enclosed
screws or double-sided sticker.
Figure B- 50: EL-4761 Flood Detector
2.
Secure the flood detector cable to the wall.
It is recommended to place the flood detector cable inside metal or plastic pipes
iConnect
Installation Manual
109
Appendix B: Transmitter Installation
Installation Procedure
After the transmitter has been registered mount the transmitter as follows:
Before permanently mounting the unit, test the transmitter from the exact mounting
position. If necessary, improve the position of the transmitter. The alarm is generated by
pressing the tamper switch.
1.
Open the transmitter housing.
2.
Remove the PCB by pressing the PCB release tab.
3.
Mount the back cover using two screws and replace the PCB. Use ISO 7050 (ST3.5 x 22) or similar countersunk
screws so that the screw head will not touch the PCB.
When handling the PCB, do not apply pressure on the antenna.
The upper screw is also used for back tamper. When the transmitter is removed from the
wall, the screw causes the tamper release to break away from the back cover and the rear
tamper switch is released.
4.
Knockout the wiring hole in the back cover.
5.
Thread the wires through the wiring hole.
6.
Connect the terminal block.
7.
Test the transmitter, making certain that the LED is lit during transmission.
8.
Close the front cover of the transmitter.
Deleting a Flood Detector
To delete a flood detector from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[1] (Programming > Devices > Zones).
• Select a zone and press '√ʹ
2.
Press >12 >√.
3.
Open the detector and take out the battery.
4.
Press the tamper switch. While the tamper switch is being pressed insert the battery.
5.
Within five seconds open the tamper and close it again.
110
iConnect
Installation Manual
Appendix B: Transmitter Installation
Indoor Siren (EL-4723)
The EL-4723 is a 2-Way Wireless Indoor Siren for use with the iConnect
Control System. In the event of an alarm the
control system activates the siren. The Wireless Indoor Siren is sounded until the end of the control-system-programmed
siren cutoff.
Location of the Siren
Consider the following before mounting the siren:
• Choose a suitable mounting location for the siren.
• The siren should be mounted on a flat surface in a highly visible position for maximum deterrence against
potential intruders.
• Before permanently mounting the siren, test the reception from the exact mounting position.
Always wear ear protectors when installing indoor/outdoor sirens
Registration Procedure
The EL-4723 must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[5]>[1] (Programming > Devices > Siren>WL Siren)
• Select a siren from the list (1-4) and press '√ʹ.
2.
Release the mounting bracket captive locking screw.
Figure B- 51: Releasing the locking screw
Figure B- 52: Inserting the batteries
3.
Open the housing – lift the front cover away from the rear housing.
4.
Insert the batteries while paying attention to polarity.
Figure B- 53: Inserting the batteries (#2)
5.
The siren will send a transmission. If the transmission is successfully received by the system it will play a
confirmation sound. If no confirmation sound is heard send another transmission by pressing and releasing
the tamper switch of the siren.
6.
As soon as 'Save?' appears press '√ʹ.
iConnect
Installation Manual
111
Appendix B: Transmitter Installation
Installation Procedure
After the siren has been registered mount the unit as follows:
1.
Place the back cover in position against the wall and mark the upper and lower mounting holes.
2.
Install wall anchors in the appropriate positions.
3.
Attach the back cover to the wall using supplied screws.
Mounting
Bracket
Tamper
Protection
Screw
Figure B- 54: Attaching the mounting bracket
4.
Mount the siren to the mounting bracket by turning the siren clockwise.
5.
Secure the captive locking screw.
Testing the Siren
Once the siren has been registered test the unit according to the following testing procedure:
To perform a siren test:
1.
Go to the main menu and select [7]>[0]>[3]>[1] (Service> Tests> WL Siren Test).
2.
Select a siren from the list (1-4) and press '√ʹ. The selected Siren is sounded briefly.
Deleting a Siren
To delete a siren from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[5] (Programming > Devices > Siren)
• Select a siren from the list (1-4) and press '√ʹ.
2.
Press >3>'√ʹ. Upon the ‘OK’ confirmation request, press ʹ√ʹ
3.
Open the siren and take out the battery.
4.
Press the tamper switch. While the tamper switch is being pressed insert the battery. Within five seconds open the
tamper and close it again.
112
iConnect
Installation Manual
Appendix B: Transmitter Installation
Outdoor Siren and Strobe (EL-4726T)
The EL-4726T is a 2-Way Wireless Outdoor Siren Strobe for use with the iConnect
Control System. In the event of an
alarm the control system activates the siren and strobe. The Wireless Siren is sounded until the end of the control-systemprogrammed siren cutoff. After the siren cutoff has expired, the strobe continues to flash until the system is disarmed.
Location of Siren Strobe
Consider the following before mounting the siren strobe:
• Choose a suitable mounting location for the siren strobe.
• The siren strobe should be mounted on a flat surface in a highly visible position for maximum deterrence
against potential intruders.
• Before permanently mounting the siren strobe, test the reception from the exact mounting position.
Always wear ear protectors when installing indoor/outdoor sirens
Registration Procedures
The EL-4726T must identify itself to the iConnect
1.
Control System as follows:
Set the system to registration mode.
• Go to the main menu and select [9]>[1]>[5]>[1] (Programming > Devices > Siren>WL Siren)
• Select a siren from the list (1-4) and press '√ʹ.
2.
Open the screw cover by applying thumb pressure on the screw cover lower part.
3.
Open the cover screw and lift the front cover away from the rear housing.
4.
Open the battery housing cover
5.
Insert the batteries while paying attention to polarity.
Figure B- 55: Inserting the batteries
6.
The siren will send a transmission. If the transmission is successfully received by the system it will play a
confirmation sound. If no confirmation sound is heard send another transmission by pressing and releasing
the tamper switch of the siren.
7.
As soon as 'Save?' appears press '√ʹ.
Installation Procedure
After the siren strobe has been registered mount the unit as follows:
1.
Place the back cover in position against the wall and mark the upper and lower mounting holes.
2.
Install wall anchors in the appropriate positions.
3.
Attach the back cover to the wall using supplied screws.
4.
Mount the siren strobe to the mounting bracket.
5.
Close the battery housing cover and replace the front cover. Pay attention to the tamper switch.
6.
Secure the cover screw and replace the screw cover.
iConnect
Installation Manual
113
Appendix B: Transmitter Installation
Testing the Siren Strobe
Once the siren strobe has been registered test the unit according to the following testing procedure:
To perform a siren strobe test
1.
Go to the main menu and select [7]>[0]>[3]>[1] (Service> Tests> WL Siren Test).
2.
Select a siren from the list (1-4) and press '√ʹ. The selected siren is sounded briefly.
Deleting the Siren Strobe
To delete a siren strobe from the system:
1.
Set the system to Delete mode.
2.
Go to the main menu and select [9]>[1]>[5] (Programming > Devices > Siren).
3.
Press >5, and press '√ʹ. Upon the ‘OK’ confirmation request, press ʹ√ʹ
4.
Open the siren strobe and take out the batteries.
5.
Press the tamper switch. While the tamper switch is being pressed insert the batteries. Within five seconds open the
tamper and close it again.
114
iConnect
Installation Manual
Appendix B: Transmitter Installation
I/O Expander Module (EL-4770)
The 2-Way Wireless I/O Expander Module (EL-4770) is an extension module enabling wired devices to be connected to
Control System (SW versions 305 and above). The iConnect
Control System supports up-to two 2-Way
the iConnect
Wireless I/O Expander Modules. Each 2-Way Wireless I/O Module supports 8 hardwired zone inputs, 2 auxiliary outputs
and has the capability to control up to 2 PGM devices. Each output or PGM device can be operated in a response to a
wide variety of system events.
The 2- Way Wireless I/O Expander Module is installed outside the Control System in its own dedicated plastic unit
equipped with case open and wall removal tamper protection. The Wireless I/O Module is also provided with its own
power supply and backup battery.
1.
Backup battery connector
2.
Power input jack (by external AC/DC adaptor)
3.
Auxiliary parallel outputs (Aux1-2) for powering detection devices
4.
Zone inputs (loop type configurable in programming)
5.
Programmable outputs (PGM): dry contact
6.
Back tamper switch connector
7.
Tamper bypass dip switch
8.
Front case tamper switch
9.
Antenna (868 or 433)
10. LED indicator
Figure B- 56: I/O Expander Module circuit board and plastic unit
Table B-9: LED Indication
LED
Red
Orange
Green/Red (tamper open)
State
On
Flashing
Off
Flashing
Flashing
Description
AC and batteries OK
AC trouble
Power not present
Low battery
Green – Signal reception
Red – Signal transmission
Box & Wall Tamper
Box and wall tamper switches provides extra protection. If the plastic unit is opened the front tamper switch is released
and an alarm is generated. In the event that the plastic unit is removed from the wall, the screw causes the perforated
section of the plastic and attached tamper mechanism metal plate to break and remain attached to the wall. As a result,
the back tamper switch is released and an alarm is generated.
The front tamper switch is located on the front of the circuit board and is depressed via a spring when the front plastic
cover is closed. The back tamper switch is located on the rear side of the back panel and is constantly depressed.
iConnect
Installation Manual
115
Appendix B: Transmitter Installation
Attach the tamper hole to the wall during mounting and attach the tamper connector and lead to the main panel.
Set the Tamper dipswitch SW1 according to your tamper protection preferences, see Tamper Bypass section, below.
Tamper Bypass
The circuit board provides an option to bypass the front and back tamper, as shown in the following table:
Table B-10: Tamper Bypass Settings
Dipswitch SW1
Setting
ON
OFF
Description
Tamper bypass is in effect. Use this setting
during programming and if no back tamper
has been connected.
(Default): No tamper bypass is in effect. Use
this option when back tamper is connected
to the system.
Choosing the Mounting Location
Before you mount the 2-Way Wireless I/O Expander Module plastic unit, study the premises carefully for the best
possible coverage and yet easily accessible to devices and accessories. Consider the following before mounting the 2-Way
Wireless I/O Expander Module plastic unit:
• Centrality of location among all the detection devices and transmitters
• Proximity to an uninterrupted AC power supply
• Distance from sources of interference, such as direct heat sources, electrical noise such as computers,
televisions etc., large metal objects, which may shield the transmission antenna
• Dryness
Mounting the I/O Expander Module
The 2-Way Wireless I/O Expander module unit consists of back and front panels and features plastic click-mounting for
all internal components.
1.
Separate the sub-assemblies by pressing the circular locking plastic brackets on either side to release the front cover
(see below).
Figure B- 57: Box clip release
2.
Remove the circuit board and if required open knock outs for the entry of input and power wires.
3.
Hold the mounting bracket against the wall as a template and mark the locations for the mounting holes (4
mounting holes and an additional optional hole for securing the tamper protection bracket item).
Figure B- 58: Mounting screw template
4.
Drill the desired mounting holes and place the screw anchors.
Do not permanently mount the plastic unit at this point of the installation
116
iConnect
Installation Manual
Appendix B: Transmitter Installation
Wiring the I/O Expander Module
AC Adaptor and Circuit Board
The 2-Way Wireless I/O Expander Module is powered by an AC/DC Adaptor 100-240V, 50/60Hz/14.4V,1.5A. Connection
to AC power supply must be permanent and connect through the mains-fuse terminal block (see below).
Caution
AC wiring should be done by a certified electrician
1.
Connect the AC adapter to the main fuse terminal block (see below).
Figure B- 59: AC adapter and circuit board placement
2.
Reinstall the circuit board and connect the power source plug to the power input jack on the circuit board.
Caution
Do not connect to main AC power at this point of the installation
3.
Wire all input and output peripherals as described in the following sections.
Zone Input Wiring
The 2-Way Wireless I/O Expander Module supports 8 hardwired zones (defined in the iConnect
Control System) that
can be defined as Normally Open, Normally Closed or End of Line Resistor zones. Zone connection configuration must
be defined accordingly at each zone’s programming parameters.
Auxiliary Output (AUX) Wiring
The 2-Way Wireless I/O Expander Module includes 2 auxiliary outputs (12±2VDC 1000mA). Use the auxiliary output
terminals to power PIRs, glass-break detectors, smoke detectors, audio switches, photoelectric systems and/or any device
that requires a 9VDC power supply.
The total power from the AUX terminals should not exceed 1000 mA
Programmable Output (PGM) Wiring
The 2-Way Wireless I/O Expander Module enables the iConnect
Control System to control PGM devices. The PGM is a
programmable output that is triggered according to specific system status condition.
Connect a PGM device to the PGM output. PGM control configuration must be defined accordingly at each PGM’s
programming parameters.
Backup Battery Connection
Insert the backup battery into its place and connect the lead connector to the backup battery jack on the circuit board.
iConnect
Installation Manual
117
Appendix B: Transmitter Installation
Caution
The circuit board is designed to work with all approved 12VDC,7Ah sealed lead batteries as
a backup for the primary power supply in time of main power failure.
The circuit board is designed with reverse polarity protection on the battery charging
circuit. However, prolonged improper connection of the battery to the circuit board will
result in damage.
The battery is not supplied with the 2-Way Wireless I/O Expander Module.
The rechargeable battery should be charged for at least 72 hours.
Battery presence is checked every 10 seconds.
There is a risk of explosion if a battery is replaced with an incorrect type.
Dispose of used batteries according to the proper instructions.
Battery in product shall be replaced every 3-5 years. No maintenance is needed.
The power should remain disconnected until all connections have been made and checked
for accuracy.
Completing the Installation
To complete the installation:
1.
Mount the 2-Way Wireless I/O Expander Module back panel to the wall using affixing screws.
2.
Connect the 2-Way Wireless I/O Expander Module to the AC mains power.
Caution
When the circuit board is powered on, mains voltage is present on the main PCB.
To prevent risk of electric shock, disconnect all power (AC transformer and battery) before
servicing.
Under no circumstances should mains power be connected to the PCB other than through
the main terminal block.
A readily accessible disconnection device shall be incorporated in the building installation
wiring.
For continued protection against risk of fire, replace fuses only with fuses of the same type
and rating.
3.
Before closing the front cover and securing the locking screw, proceed to Registering the 2-Way Wireless I/O
Expander Module, below.
Registering the I/O Expander Module
The 2-Way Wireless I/O Expander Module must identify itself to the iConnect
1.
Control System as follows:
Set the control system to registration mode.
• Go to the main menu and select [9]>[1]>[6] (Programming > Devices > Zone Expanders)
• Select a 2-Way Wireless I/O Expander Module from the list (1-2) and press '√ʹ.
2.
With the plastic unit cover open send a transmission by pressing and releasing the tamper switch of the Wireless
I/O Expander Module. The 2-Way Wireless I/O Expander Module will send a transmission to the control
system. If the transmission is successfully received by the control system it will play a confirmation sound.
3.
As soon as 'Save?' appears press '√ʹ.
4.
Close the 2-Way Wireless I/O Expander Module front cover and secure the locking screw.
118
iConnect
Installation Manual
Appendix B: Transmitter Installation
Deleting the I/O Expander Module
To delete a 2-Way Wireless I/O Expander Module from the system:
1.
Set the system to Delete mode.
• Go to the main menu and select [9]>[1]>[6] (Programming > Devices > Zone Expanders).
• Select a 2-Way Wireless I/O Expander Module from the list (1-2) and press '√ʹ.
2.
Press >3, and then press '√ʹ. Upon the ‘OK’ confirmation request, press ʹ√ʹ
3.
Open the plastic unit (see Figure 5 1 and Figure 6 1) and disconnect the main AC power.
4.
Press the tamper switch. While the tamper switch is being pressed connect the power. Within five seconds open the
tamper and close it again.
iConnect
Installation Manual
119
Appendix B: Transmitter Installation
Transmitter Specifications
The technical specifications for the transmitters that appear in this appendix are listed below. All transmitters are
available in 868, or 433MHz (optional) FM frequencies.
El-4755 PIR
Frequency: 868* or 433MHz
Power: 3.6VDC AA Lithium Battery (x 2)
Current Consumption: 200mA (capture with flash), 42µA (standby)
Pyroelectric Sensor: Dual Element
Maximum Coverage: 14 x 14m
Pulse Count: 1 or 2
LED Indicator: Selectable
Digital Adaptive Temperature Compensation
RFI Immunity: According to EN 50130-4
Operating Temperature: 0 to 60°C
Fire Protection: ABS Plastic Housing
Dimensions: 110 x 62 x 50mm
* Complies with EN-50131 2-2 Grade 2 Class II, Power Supply Type C
El-4755PI PIR
Frequency: 868* or 433MHz
Power: 3.6VDC AA Lithium Battery (x 2)
Current Consumption: 200mA (capture with flash), 42µA (standby)
Pyroelectric Sensor: Dual Element
Maximum Coverage: 11 x 11m
Pulse Count: 1 or 2
LED Indicator: Selectable
Digital Adaptive Temperature Compensation
RFI Immunity: According to EN 50130-4
Operating Temperature: 0 to 60°C
Fire Protection: ABS Plastic Housing
Dimensions: 110 x 62 x 50mm
* Complies with EN-50131 2-2 Grade 2 Class II, Power Supply Type C
El-4745 PIR
Frequency: 868* or 433MHz
Power: 3.6V ½ AA Lithium Battery (Optional x 2)
Current Consumption: 30mA (transmission), 35µA (standby)
Pyroelectric Sensor: Dual Element
Maximum Coverage: 14 x 14m
Pulse Count: 1 or 2
LED Indicator: Selectable
Digital Adaptive Temperature Compensation
RFI Immunity: According to EN 50130-4
Operating Temperature: 0 to 60°C
Fire Protection: ABS Plastic Housing
Dimensions: 110 x 62 x 50mm
* Complies with EN-50131 2-2 Grade 2 Class II, Power Supply Type C
El-4745PI PIR
Frequency: 868* or 433MHz
Power: 3.6V ½ AA Lithium Battery (Optional x 2)
Current Consumption: 30mA (transmission), 35µA (standby)
Pyroelectric Sensor: Dual Element
Maximum Coverage: 11 x 11m
Pulse Count: 1 or 2
LED Indicator: Selectable
Digital Adaptive Temperature Compensation
RFI Immunity: According to EN 50130-4
Operating Temperature: 0 to 60°C
Fire Protection: ABS Plastic Housing
Dimensions: 110 x 62 x 50mm
* Complies with EN-50131 2-2 Grade 2 Class II, Power Supply Type C
120
EL-4601DZ Magnetic Contact/ Universal Transmitter
Frequency: 868* or 433MHz
Power: 3.6VDC ½ AA Lithium Battery
Current Consumption: 25mA (transmission), 10µA (standby)
RFI Immunity: According to EN 50130-4
Operating Temperature: 0-60°C
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL-4602 Universal Transmitter
Frequency: 868* or 433MHz
Power: 3.6VDC ½ AA Lithium Battery
Current Consumption: 25mA (transmission), 10µA (standby)
RFI Immunity: According to EN 50130-4
Operating Temperature: 0-60°C
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL-4607 Vibration Detector
Frequency: 868* or 433MHz
Power: 3.6VDC ½ AA Lithium Battery
Current Consumption: 25mA (transmission), 10µA (standby)
RFI Immunity: According to EN 50130-4
Alarm Delay During Normal Operation: Approx. 4 minutes
Operating Temperature: 0-60°C
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL-4703 Smoke Detector
Frequency: 868* or 433MHz,
Power: 2xCR123 3V Lithium battery
Average Standby Current: 0.04mA
Test Current: 55mA
Alarm Current: 55mA
Peak Trouble Pulse Current: 4.73mA
Peak Pulse Current: 0.074mA
Alarm Sound Level: Exceeds 85dB at 3m (10 feet)
Operating Temperature: -10°C to 40°C (14°F - 104°F)
Dimensions: Diameter: 148 x 53mm
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL-4714 Keyfob
Frequency: 868* or 433MHz
Power: 3V Lithium Battery, Type CR2032
Current Consumption: 16mA (transmission), 0.2µA (standby)
RFI Immunity: According to EN 50130-4
Operating Temperature: 0-60°C
*Complies with EN- Grade 2 Class II Power Supply Type C
EL-4611M/P Keyfob
Frequency: 868* or 433MHz
Power: 3V Lithium Battery, Type CR2032
Current Consumption: 16mA (transmission), 0.2µA (standby)
RFI Immunity: According to EN 50130-4
Operating Temperature: 0-60°C
*Complies with EN- Grade 2 Class II Power Supply Type C
iConnect
Installation Manual
Appendix B: Transmitter Installation
EL-4727 Wireless LCD Keypad
Frequency 868* or 433MHz
Power: 4x1.5V Lithium AA batteries
Current consumption : up to 100mA (transmission),
50µA (standby)
Operating temperature: 0°C to 60°C (32°F to 140°F)
Dimensions: 214 x 110 x 35mm
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL- 4762 Gas Leak Detector
Frequency: 868* or 433MHz
Power: AC120V/AC230V (model dependant)
Signal Volume: Approx. 85 dB at a distance of 3 meters
Operating Temperature: 0°C to 40°C (32°F to 122°F)
Storage Temperature: -20°C to 60°C (-4°F to 140°F)
Dimensions: 140 X 80 X 49 mm
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL- 4764 Carbon Monoxide Detector
Frequency: 868* or 433MHz
Power: 2 x CR 123, 3V Lithium Battery
Current Consumption: 20 µA (standby), 30mA (Alarm)
Signal Volume: Approx. 85 dB at a distance of 3 meters
Operating Temperature: 4°C to 38°C (39°F to 100°F)
Storage Temperature: -20°C to 60°C (-4°F to 140°F)
Dimensions: 140 X 80 X 49 mm
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL- 4761 Flood Detector
Frequency: 868* or 433MHz
Power: 3.6VDC ½ AA Lithium Battery
Current Consumption: 25mA (transmission),
40µA (standby)
RFI Immunity: According to EN 50130-4
Operating Temperature: 0-60°C
Dimensions: 65 x 30 x 25mm
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL-4723 Indoor Siren
Frequency: 868* or 433MHz
Power: 4 X CR123, 3V Lithium Battery (2 batteries for the Radio
Transceiver, 2 batteries for the Speaker)
Current Consumption: 25mA (transmission), 40µA (standby)
Siren Output: Approx. 85dB @ 1m
Operating Temperature: -25°C to 60°C (-4°F to 140° F)
Dimensions: Ø183 x 51 mm
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL-4726 Outdoor Siren/Strobe
Frequency: 868* or 433MHz
Power: 4 X CR123, 3V Lithium Battery (2 batteries for the Radio
Transceiver, 2 batteries for the Speaker)
Current Consumption: 25mA (transmission), 40µA (standby)
Siren Output: Approx. 105dB @ 1m
Operating Temperature: -25°C to 60°C (-4°F to 140° F)
Dimensions: 340 x 222 x 73mm
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
EL- 4770 I/O Expander Module
Frequency: 868* or 433MHz
Power Input: AC/DC Adaptor 100-240V,50/60Hz/14.4VDC,1.5A
Current Consumption: Typical: 40 mA; 65mA maximum
Rechargeable Standby Battery: 12VDC±2VDC up to 7Ah, typical
Auxiliary Power Outputs: 12VDC@1000mA, maximum (from all
AUX terminals)
PGM Relay Output Dry Contact Rating: Dry contact –
1A@30VDC,0.5A@25VDC
Number of Zones: 8
Zone Loop Type: N.C. / N.O. / E.O.L. (Programmed at the Control
System)
Tamper Protection: Front cover and back tamper (N.C.)
RF immunity: According to EN50130-4
Operating temperature: -10°C to 40°C (14°F to 104°F)
Storage temperature: -20°C to 50°C (-4°F to 122°F)
Usage: Indoor
Dimensions (Plastic Case): 290 x 254 x 97 mm (11.2 x 9.7 x 3.6 inch)
*Complies with EN-50131 2-6 Grade 2 Class II Power Supply Type C
Lithium Batteries
!
Fire, explosion and severe burn hazard!
When handling lithium batteries follow the listed precautions:
•Do not recharge.
•Do not deform or disassemble.
•Do not heat above 212°F (100°C) or incinerate.
Due to the occurrence of voltage delay in lithium batteries that
have been in storage, the batteries may initially appear to be
dead. In this case, leave the unit in Test mode or Radio mode
for a few minutes until the battery voltage level is stabilized.
iConnect
Installation Manual
121
Appendix C: Web User Application
Appendix C: Web User Application
The Web Application provides a full interface to all of the system’s user functions. Via the Web, the end user can
perform a wide range of tasks such as arm/disarm, zone bypass, user code management and home automation control.
You can also access the Web User Application from your cellular phone or PDA using the WAP protocol.
Log In Page
This application is usually part of the service provider’s Web site and requires the end user to log in to gain access to
the page.
To enter the Web Application, on your browser enter the Web page address supplied by your WEB service provider
and press Go. You will see the Login Page.
Figure C- 1: Login Page
To login to the Web Application, enter your user name and password supplied by your WEB service provider, and the
passcode which is your User Code, then click the Enter button.
For your system security reasons, you must change the password immediately at first login.
You can change your password on the Change Password page that is accessible from the
Settings menu. Your new password should be no less than six characters and must start with
a letter.
The Main Page
After logging in, your system’s home page (Main Page) is displayed.
Menu Bar
Workspace
Status Bar
Figure C- 2: The Main Page
122
iConnect
Installation Manual
Appendix C: Web User Application
When using the
Smartphone application
service, the main page
looks the following way:
Figure C- 3: The Main Page (Smartphone Application)
Menu Bar
The Menu Bar includes the Main Menu, arm/disarm options list and the Log Off button. The Main Menu offers links to
various pages in the Web Application. Use the Logoff button on the right side menu to properly close the session.The
following options are available from the Main Menu:
• Home – pressing the Home button allows the user to return to the Main page at any time
• Automation – allows control or scheduling of automated lights and appliances.
• Video – provides access to view streaming video from IP cameras.
• My Account – offers various options including user code and contact management, event log viewing and
zone bypass.
• Help – offers online explanations on how to use the Web Application plus FAQ and customer support
options.
Status Bar
The Status bar displays information on your system’s status and the name of the user currently logged in. Above the
status bar, the time when the system status display was last updated is shown. This information is displayed according
to the local time at the control system. When logging into the WUApp with a GPRS Control System, the system status
refreshes automatically, and can be refreshed manually as well. To refresh the current system status, click the Refresh
Status button on the right-hand side of the Status bar.
Workspace
The workspace offers additional links to the following pages of the application: Users and Codes, History, Automation,
Alerts, Change Password, Video. When you choose a page, either from the Main Menu, or from the workspace, the
page is displayed in the workspace. For example, if you choose Automation from the Main Menu, a list of automated
appliances is displayed in the workspace.
SMS alerts relate only to SMS sent from ELAS (WEB User Application).
iConnect
Installation Manual
123
Appendix C: Web User Application
Options Available from Main Page
Arm/Disarm
Figure C- 4: Arm/Disarm Page
You can arm and disarm the system using the Arm/Disarm drop-down box (upper-right part of the page) or using the
buttons in the System Operation Area.
The Web Application allows you to arm and disarm your system via the Web Application using any of the available
arming methods. It is important to note that when you arm using the Web application, the system is armed with the
programmed delay.
1.
On the Status Bar below on the page you can see the current status of the system (in our example it is Disarmed
and System Ready, which means that the system and all the detectors are working properly and there are no
events to report).
2.
It is possible to check if there were alarms in the system – see p. 129, History.
System Users and Codes
In this area you can add, delete, or change users and the User Codes for your system (for example, add codes for family
members).
1.
On The Main Page menu, click Settings.
Figure C- 5: Settings Button
124
iConnect
Installation Manual
Appendix C: Web User Application
2.
Click System Users and Codes, the following page appears:
Figure C- 6: System Users and Codes Page
Web Interface Users and Codes
The Users and Codes page provides a useful tool for managing your system’s users. From this page you can add, edit
and delete users as required. You can even issue temporary (limited) codes to guests that will expire after 24 hours.
For further information on user codes and their various uses, see p. 21, 4.4 User Codes.
On The Main Page menu, click Settings, then Web Interface Users and Codes, the following page appears:
Figure C- 7: Web Interface Users and Codes Page
iConnect
Installation Manual
125
Appendix C: Web User Application
Change Password
Click Settings then Change Password to change the password you use to login to the Web Application.
Figure C- 8: Change Password Page
Zone Bypass
On The Main Page menu, click Settings then Zone Bypass to bypass certain zones in your home that you don't want to
receive event messages from – see p. 21, Zone Bypassing/Unbypassing. Select the checkboxes for the zones you want to
bypass.
Figure C- 9: Zone Bypass Page
126
iConnect
Installation Manual
Appendix C: Web User Application
Change Appearance
On The Main Page menu, click Settings then Change Appearance to change the color scheme of your account.
Figure C- 10: Change Appearance Page
Alerts
The Alerts page allows you to enter the details of contacts you wish to be informed when events occur in your system.
For example, you can enter your own email address and/or cellular phone number so that you will receive email or
SMS notification in the event of an alarm.
This area allows you to program where to send the alerts on home events (arming, disarming, alarm etc.) The events
can be reported via email or your cellular phone.
1.
On The Main Page menu, click the Alerts area.
Figure C- 11: Alerts Area
iConnect
Installation Manual
127
Appendix C: Web User Application
The following page appears:
Figure C- 12: Alerts Page
2.
Press Add new to add email addresses or cellular telephone numbers for the alert messages.
Figure C- 13: Add New Contact Page
3.
In the Contact Name field, enter the name of the contact to receive alerts.
4.
In the Email Address field, enter the email address for email alerts.
5.
In the Cellular Phone # field, enter the cellular phone number for SMS alerts.
6.
To start receiving the events messages, in the area below, select the checkboxes according to the event type and
message type you prefer (email or SMS).
7.
Test the alerts you have programmed by clicking the Test button on the Alerts page near the newly added alert.
128
iConnect
Installation Manual
Appendix C: Web User Application
History
The History page enables you to view the system’s event log. The events are arranged in a table that offers the
advantage of allowing you to view a large number of events at once. In addition to viewing the event log, you may also
save the log to a file (HTML, PDF or RTF) or print the log.
For further details on how to use the Web Application, refer to the Help menu included in the application.
• On The Main Page menu, click History, the following page appears:
Figure C- 14: History Page
You can save or print the LOG from this page.
Automation
The Web Application allows you to control and schedule automated lights and appliances in your home. The
application offers a comprehensive interface that enables you to view the settings for all of your automated devices at
once. Additionally, you can add, edit or delete devices from the comfort of your PC.
Discuss this capability with your security service provider to determine if it is applicable to your system – see p. 33
Home Automation and PGM Control.
• On The Main Page menu, click Automation, the following page appears:
Figure C- 15: Automation Page
You can program turning the HA units on/off at specific hour/day of the week.
Video
Using 2-way video verification PIR detectors (EL-4755/EL-4755PI) installed in your home, the Web Application enables
you to view video images over the Web in order to check your home and family while you are away.
Discuss this capability with your security service provider to determine if it is applicable to your system.
iConnect
Installation Manual
129
Appendix D: Event Table*
Appendix D: Event Table*
Burglary
Description
Restore
SIA
Contact ID
Address Field
NBA
1130
Device Number
NBR
3130
Device Number
NUB
1570
Device Number
NUU
3570
Device Number
NTA
1137
Device Number
NTR
3137
Device Number
NPA
1120
Device Number
NPR
3120
Device Number
Panic Alarm
NPA
1120
Device Number
Tamper
NTA
1137
Device Number
NTR
3137
Device Number
NHA
1121
—
Alarm from Zone
Zone Alarm Restore
Zone Bypassed
Zone Unbypassed
Zone Tamper
Zone Tamper Restore
Zone Panic Alarm
Zone Panic Restore
Tamper Restore
Duress
Bell Cancel
NBC
1521
User Number
Disarm after Alarm
NOR
1458
User Number
Water Alarm
NWA
1154
Device Number
NWH
3154
Device Number
NUA
1150
Device Number
Water Alarm Restore
Environmental Alarm
Environmental Alarm Restore
NUH
3150
Device Number
Exit Error
NEE
1457
User Number
….
….
….
NFA
1110
Device Number
NFR
3110
Device Number
NGA
1151
Device Number
NGH
3151
Device Number
Full Arm
NCL
3401
User Number
Part Arm
NCG
3456
User Number
Perimeter Arm
NCG
3441
User Number
Disarm (entire system)
NOP
1401
User Number
Crash and Smash
Fire
Fire Alarm
Fire Alarm Restore
Gas Alarm
Gas Alarm Restore
Open/Close
*
130
= Events that are displayed in the event log only when viewed by the installer.
iConnect
Installation Manual
Appendix D: Event Table*
Service
Description
SIA
Contact ID
Address Field
Edit User Code
Restore
NJV
1462
User Number
Delete User Code
NJX
3462
User Number
System Programming
NLB
1627
—
End System Programming
NLX
1628
—
Remote Programming
NRB
1412
—
End Remote Programming
NRS
3412
—
Walk Test
NTS
1607
User Number
End Walk Test
NTE
3607
—
Set Time
NJT
1625
User Number
Set Date
NJD
1625
User Number
NLB
1621
User Number
NYT
1302
Device Number
NYR
3302
Device Number
NXT
1384
Device Number
NXR
3384
Device Number
NAT
1301
Device Number
Clear Log
Power
Battery Low
Battery Restore
Transmitter Low Battery
Transmitter Battery Restore
AC Loss
AC Restore
NAR
3301
Device Number
Power up (user-log)
NRR
3301
Device Number
NLT
1351
Device Number
NLR
3351
Device Number
NET
1330
Device Number
NER
3330
Device Number
NUT
1341
Device Number
NUR
3341
Device Number
NUT
1341
Device Number
NUR
3341
Device Number
NUS
1381
Device Number
NUR
3381
Device Number
NYY
1605
Signal Level (0-9)
NBT
1380
Device Number
NBJ
3380
Device Number
NXQ
1344
Device Number
NXH
3344
Device Number
NMA
1100
Device Number
NMR
3100
Device Number
NNA
1102
Device Number
Peripherals
Media Loss
Media Loss Restore
Device Trouble
Device Trouble Restore
Transmitter Out of Synch.
Transmitter Re-synch.
CP Transmitter Out of Synch.
CP Transmitter Re-synch.
Supervision Loss
Supervision Restore
GSM Signal Level
Zone Trouble
Zone Trouble Restore
RF Jamming
FM Jamming
FM Jamming Restore
Medical
Medical Alarm
Medical Alarm Restore
No Motion
iConnect
Installation Manual
131
Appendix D: Event Table*
Unclassified Events
Description
SIA
Contact ID
Address Field
Periodic Test
Restore
NRP
1602
—
No Arm
NCD
1654
—
NOC
1406
—
Cancel Report
Address Field
The address field provides additional information regarding the event. This information is forwarded as numeric data
according to the following tables.
132
DEVICE NUMBER
USER NUMBER
Value
Description
Value
Description
00
Control System
00
Control System
01-33
Zones
01-32
Users
41-59
Keyfobs
34
Remote Access
65
Home Automation Module
41-59
Keyfobs
77-80
Repeaters
61-76
Smartkeys
81-84
Wireless Keypads
81-84
Wireless Keypads
91
Front Panel Keypad
91
Front Panel Keypad
92-98
Hardwire Keypads
92-98
Hardwire Keypads
110
Wireless Siren
242
Communication Module
243
PSTN Communication Interface
244
Cellular Communication Interface
245
Ethernet Communication Interface
249
GPRS Communication Interface
iConnect
Installation Manual
Appendix E: Zone Types
Appendix E: Zone Types
Normal
A Normal zone is active when the system is armed. This zone generates a Burglary alarm instantly when triggered.
Normal zones are designed for detectors installed inside the protected site or doors/windows that are never used to
enter the premises.
Event Group: Burglary
Entry/Exit
When the system is armed, Entry/Exit zones initiate the entry delay when triggered. If the system is not disarmed by the
time the entry delay expires, a Burglary alarm is generated. These zones are designed for detectors protecting the
entrance to the protected site
Event Group: Burglary
Follower
If an Entry/Exit zone is triggered first, Follower zones do not generate an alarm when triggered during the entry delay.
If the system is not disarmed by the end of the entry delay, the Follower zone generates an alarm. A Follower zone
instantly generates an alarm if triggered when the entry delay is not active. These zones are designed for detectors
protecting the area in which a keypad has been installed or the area crossed in order to reach the keypad.
Event Group: Burglary
Panic
Panic zones are always active. When a Panic zone is triggered, a Panic alarm is generated. This zone type is designed
for panic buttons that may be pressed in a robbery situation. If the Bell option is disabled for Panic zones, in addition to
the siren not sounding, all forms of alarm indication from the keypad are also disabled.
Event Group: Burglary
Medical
Medical zones are always active. When triggered, Medical zones generate a Medical alarm. These zones are used
typically with panic buttons that may be pressed in the event of a Medical.
Event Group: Medical
Fire
Fire zones are always active. When triggered, Fire zones generate a Fire alarm. These zones are designed for use with
smoke detectors and panic buttons that may be pressed in the event of a fire. A Fire zone always activates the siren even
if the Bell option is programmed as disabled. Fire alarms sound a pulsating siren to distinguish them from other alarms.
Event Group: Fire
24Hr
24Hr zones are always active. When triggered, 24Hr zones generate a Burglary alarm. These zones are used for
applications that require constant protection.
Event Group: Burglary
24Hr-X
The 24Hr-X zone is a future option that is not available in the current firmware.
Event Group: Not applicable
Gas
Gas zones are always active. In the event of a gas leak, these zones generate a Gas alarm. Gas zones are typically used
with methane/propane/butane or carbon monoxide gas detectors. Gas alarms sound a distinctive siren pattern to easily
distinguish them from other alarms. A gas alarm causes the siren to sound until the alarm is restored; the siren cut-off
does not apply to gas alarms.
Event Group: Fire
iConnect
Installation Manual
133
Appendix E: Zone Types
Flood
Flood zones are always active. When triggered, Flood zones generate a Water alarm. These zones are designed for use
with EL-4761 flood detectors.
Event Group: Burglary
Environmental
Environmental zones are always active. When triggered, these zones generate an Environmental alarm. These zones are
designed for applications that monitor environmental conditions such as temperature or humidity. If the Bell option is
enabled for Environmental zones, the system sounds trouble tones from the keypad. These tones are sounded until the
user presses on their keypad. Environmental alarms are not affected by the expiry of the siren cut-off.
Event Group: Burglary
No Motion
No Motion zones are used to monitor the activity of disabled or elderly people. If a No Motion zone has not been
triggered within a pre-defined period of time (0 to 72 hours), a No Motion event message is sent to the central station.
Event Group: Medical
Arm/Disarm
The Arm/Disarm zone is a future option that is not available in the current firmware.
Event Group: Not applicable
Crash and Smash
This zone type can be used in cases where the alarm system, is positioned at the entrance of the premises. If a burglar
breaks the door and smashes the alarm system, during the entry delay time and before a confirmed break-in event can
be sent, a suspected break-in alarm event is sent to the monitoring station.
Event Group: Burglary
Not Used
This zone type is a future option that is not available in the current firmware.
Event Group: Not applicable
134
iConnect
Installation Manual
Electronics Line 3000 Ltd. Limited Warranty
EL and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and
workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect
the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller
cannot guarantee the performance of the security system which uses this product. Sellers' obligation and liability under
this warranty is expressly limited to repairing and replacing, at Sellers option, within a reasonable time after the date of
delivery, any product not meeting the specifications. Seller makes no other warranty, expressed or implied, and makes
no warranty of merchantability or of fitness for any particular purpose. In no case shall seller be liable for any
consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other
basis of liability whatsoever. Sellers obligation under this warranty shall not include any transportation charges or costs
of installation or any liability for direct, indirect, or not be compromised or circumvented; that the product will prevent
any persona; injury or property loss by intruder, robbery, fire or otherwise; or that the product will in all cases provide
adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce
the risk of intruder, robbery or fire without warning, but is not insurance or a guaranty that such will not occur or that
there will be no personal injury or property loss as a result. Consequently seller shall have no liability for any personal
injury, property damage or loss based on a claim that the product fails to give warning. However, if seller is held liable,
whether directly or indirectly, for any loss or damage arising from under this limited warranty or otherwise, regardless
of cause or origin, sellers maximum liability shall not exceed the purchase price of the product, which shall be complete
and exclusive remedy against seller. No employee or representative of Seller is authorized to change this warranty in
any way or grant any other warranty.
WARNING: This product should be tested at least once a week.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to local
regulations.
Contacting Electronics Line 3000 Ltd.
International Headquarters:
Electronics Line 3000 Ltd.
14 Hachoma St., 75655
Rishon Le Zion, Israel
Tel: (+972-3) 963-7777
Fax: (+972-3) 961-6584
All rights reserved.
No part of this document may be reproduced in any form without prior written permission from the publisher.
Electronics Line 3000 Ltd. 03/2012
5IN1771
">