advertisement
Installation and operating instructions for the X10 PowerFlash
TM
Universal Interface, Model PF284
The Powerfl ash Universal Interface provides a way to interface to conventional security systems, and other contact closure or voltage output devices, to control X10 powerline controlled products, to turn on lights, fl ash lights, activate plug-in alarm sirens, etc.
TEST
1
13
9
5 M
ALL UNITS OFF
A
E
I
POWERFLASH INTERFACE
The Powerfl ash Interface has terminals for two types of inputs, determined by the INPUT slide switch:
Position A: 6-18 VDC
Position B: Dry contact closure
INPUT
A B
MODE
1 2 3
Setting up the Powerfl ash Interface
Do not connect 120V to the terminals!
• Use a small screwdriver to set the desired House Code and Unit Code A-P and 1-16.
• Adjust the MODE slide switch to select the desired mode of operation as follows:
1. Turns on all Lamp Modules and Wall Switch Modules set to the same Housecode as the Powerfl ash Interface. Also turns on Appliance Modules set to the same
Housecode and Unit Code as the Powerfl ash Interface. When the alarm is reset, only the Modules set to the same Housecode and Unit Code as the Powerfl ash
Interface are turned off.
2. Flashes all Lamp Modules and Wall Switch Modules set to the same Housecode as the Powerfl ash Interface. When reset all lights stay on.
3. Turns on Lamp Modules and Appliance Modules set to the same Housecode and
Unit Code as the Powerfl ash Interface. When reset, turns the same Module off.
• Connect the terminals on the Powerfl ash Interface to the burglar alarm or output device such as a driveway sensor or similar contact closure.
Note: Observe the polarity shown on the unit if the alarm output is DC voltage.
• Plug the Powerfl ash Interface into a 120V AC wall outlet.
Testing the Interface
• Press TEST to activate the Powerfl ash Interface according to the selected mode.
• Press ALL UNITS OFF to turn off Modules left on after activating the Interface.
Check Out our Web site at:
http://www.x10.com
For more information on X10 products and special promotional offers.
X10 Wireless Technology, Inc. 90 Day Limited Warranty
X10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10 products to be free from defective material and workmanship for a period of 90 days from the original date of purchase at retail. X10 agrees to repair or replace, at it’s sole discretion, a defective X10 product if returned to X10 within the warranty period and with proof of purchase.
If service is required under this warranty:
1. Visit www.x10.com/support/return_policy.htm, or e-mail [email protected] to obtain a
Return Merchandise Authorization (RMA) number.
2. Return the defective unit postage prepaid to X10 (see address on back).
3. Enclose a check for $4.00 to cover postage and handling.
4. Enclose a dated proof of purchase.
5. X10 is not responsible for shipping damage. Units to be returned should be packed carefully.
Please visit www.x10.com/support for help.
PF284-6/13
X10 Wireless Technology, Inc.
400 Forge Way, Suite 409-412,
RMA#
Rockaway, NJ 07866
Tear off and keep the portion to the right (setup instructions are on the other side of it) and keep for future use. visit www.x10.com/support/return_policy.htm
or e-mail [email protected] to obtain a Return Merchandise
Authorization (RMA) number.
Write your RMA number above. Tear off and tape this label to the outside of the package and mail it (postage prepaid).
Trim
Mini Timer MT13A
A Controller, Timer and Alarm Clock all in one! Programs up to eight X10 Modules to go on and off at specifi c times, up to a total of 64 timed events. Controls eight modules instantly. Dims lights too.
Maxi Controller SC503
Lets you control up to 16 X10 Modules at the touch of a button from anywhere in the house. Dims lights too!
Mini Controller MC10A
Lets you control up to eight X10 Modules at the touch of a button from anywhere in the house. Dims lights too!
2-Way Home Control Interface CM15A
Set up from a PC to control up to 256
X10 Modules. ActiveHome Pro software download & USB cable included.
Thermostat Set-Back TH2807
Automatically sets-back your central heating/air conditioning. Mounts on the wall under your existing thermostat and plugs into an Appliance Module.
Wireless Remote Control System RC5000
Lets you control 16 X10 modules from inside or outside your home. Can also dim and brighten Lamp Modules and Wall Switch
Modules. Works with the HR12A PalmPad
Remote and X10 RF Wall Switches (SS13A,
SS15A).
Lamp Module LM465
Can be Dimmed and Brightened from any
X10 Controller. Responds to “All lights on”.
Rated for 300 W. Incandescent only.
2-Way version LM14A.
SocketRocket LM15A
Screws in to an existing light fi xture. Controls up to 150W, incandescent only.
Appliance Module - AM486/AM466
Two pin polarized (AM486) or 3 pin grounded (AM466). For controlling an air conditioner, TV, stereo, etc. anywhere in the home. Rated 15A for heaters, coffee pots etc.; 1/3 H.P. for motors; 400W for TVs;
500W for lamps. 2-Way versions available
AM14A (2 pin), AM15A (3 pin).
Wall Switch Module WS467
For controlling important indoor and outdoor security lights. Replaces your existing wall switch and installs like a regular dimmer. Dimmed/brightened from any X10
Controller. Rated 500W incandescent only.
3 - Way Wall Switch Module WS4777
For controlling a light which is controlled by two switches. Same features as WS467.
Split Receptacle Module SR227
Replaces existing wall outlet. The top outlet functions like an Appliance Module, the bottom one is a regular outlet. Rated 15A.
Universal Module UM506
Isolated contact relay and beeper. Can be set for momentary or continuous operation.
Not compatible with X10 security systems.
Trim
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project