Sharp ER-A450S Owner Manual

ELECTRONIC CASH REGISTER
MODEL
ER-A450S
INSTRUCTION MANUAL
CAUTION:
The cash register and the remote drawer should be securely fitted to the supporting
platforms to avoid instability when the drawers are open.
CAUTION:
The socket-outlet shall be installed near the equipment and shall be easily accessible.
VORSICHT:
Die Netzsteckdose muß nahe dem Gerät angebracht und leicht zugänglich sein.
ATTENTION:
La prise de courant murale devra être installée a proximité de l’équipement et devra être
facilement accessible.
AVISO:
El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible.
VARNING:
Det matande vägguttaget skall placeras nära apparaten och vara lätt atkomligt.
CAUTION:
For a complete electrical disconnection pull out the mains plug.
VORSICHT:
Zur vollständigen elektrischen Trennung vom Netz den Netzstecker ziehen.
ATTENTION:
Pour obtenir une mise hors-circuit totale, débrancher la prise de courant secteur.
AVISO:
Para una desconexión eléctrica completa, desenchufar el enchufe de tomacorriente.
VARNING:
För att helt koppla fran strömmen, dra ut stickproppen.
INTRODUCTION
Thank you very much for your purchase of the SHARP Electronic Cash Register, Model ER-A450S.
Please read this manual carefully before operating your machine in order to gain full understanding of functions
and features.
Please keep this manual for future reference. It will help you, if you encounter any operational problems.
IMPORTANT
• Install your register in a location that is not subject to direct sunlight, unusual temperature changes,
high humidity or exposure to water sources and keep away from heat and magnetic sources.
Installation in such locations could cause damage to the cabinet and the electronic components.
• The register should not be operated by an individual with wet hands.
The water could seep into the interior of the register and cause component failure.
• When cleaning your register, use a dry, soft cloth. Never use solvents, such as benzine and/or thinner.
The use of such chemicals will lead to discoloration or deterioration of the cabinet.
• The register plugs into any standard wall outlet (Official (nominal) voltage).
Other electrical devices on the same electrical circuit could cause the register to malfunction.
• If the register malfunctions, call your local dealer for service - do not try to repair the register yourself.
• For a complete electrical disconnection, pull out the mains plug.
PRECAUTION
This Electronic Cash Register has a built-in memory protection circuit which is operated by rechargeable
batteries.
As you know, all batteries will, in time, dissipate their charge even if not used. Therefore to insure an adequate
initial charge in the protection circuit, and to prevent any possible loss of memory upon installation, it is
recommended that each unit be allowed to recharge for a period of 24 to 48 hours prior to use by the customer.
In order to charge the batteries, the machine must be plugged in. This recharging precaution can prevent
unnecessary initial service calls.
1
CONTENTS
INTRODUCTION ····················································································································································1
IMPORTANT ··························································································································································1
PRECAUTION························································································································································1
CONTENTS····························································································································································2
EXTERNAL VIEW ··················································································································································7
Front view ···············································································································································7
Rear view················································································································································7
PRINTER································································································································································8
KEYBOARD ···························································································································································9
1 Standard keyboard layout··························································································································9
2 Standard key number layout····················································································································10
KEYS AND SWITCHES ·······································································································································11
1 Mode switch and mode keys ···················································································································11
2 Drawer lock key ·······································································································································11
DISPLAYS ···························································································································································12
Machine state symbols ·························································································································12
FOR THE MANAGER
PRIOR TO PROGRAMMING ·······························································································································13
1 General instructions·································································································································13
2 How to program alphanumeric characters·······························································································13
Using character keys on the keyboard ·································································································13
Entering character codes······················································································································14
PROGRAMMING ·················································································································································16
Preparations for Programming ·············································································································16
Direct Programming ···········································································································································16
1 Setting the date and time·························································································································16
Date ······················································································································································16
Time······················································································································································17
2 Programming for departments ·················································································································17
Unit price ··············································································································································17
Functional selection······························································································································18
3 Price lookup (PLU) programming ············································································································20
Unit price ··············································································································································20
Functional selection······························································································································20
PLU assignment to departments ··········································································································22
4 European Article Number(EAN)/Universal Product Code(UPC) programming ·······································23
Unit price ··············································································································································23
Functional selection······························································································································24
EAN assignment to departments··········································································································26
5 Programming for discount keys ···············································································································27
Deduction amount (-)························································································································27
High amount lockout (HALO) and +/- sign (-) ···················································································28
6 Programming for percent keys ················································································································29
Percent rate (%) ·································································································································29
Sign (+/-) (%) ······································································································································29
7 Programming for exchange keys ·············································································································30
Currency exchange rate (e) ··············································································································30
8 Programming for the Å, r, p, ' and î keys··············································································30
High amount lockout (HALO) (Å, r, p, ', and î) ··································································30
2
9 Programming the tax rate ························································································································31
Tax rate ················································································································································31
Job-Code-Based Programming ························································································································32
1 Setting the date and time·························································································································32
Setting the date (#2610) ·······················································································································32
Setting the time (#2611) ·······················································································································32
2 Setting the register and consecutive numbers ························································································33
Setting the register number (#2612)·····································································································33
Setting the consecutive number (#2613)······························································································33
3 Programming the tax rate ························································································································34
Tax rate (#2711) ···································································································································34
4 Programming for departments ·················································································································35
Functional programming (#2110) ·········································································································35
Tax status (#2111)································································································································36
A limit amount (HALO) of entry (#2112) ·······························································································37
Alphanumeric characters (#2114) ········································································································38
Unit price (#1110) ·································································································································38
Commission group assignment (#2115)·······························································································39
Group number (#2116) ·························································································································40
Department key positioning (#2119)·····································································································41
5 Price lookup (PLU) programming ············································································································42
Department assignment (#1200, 2230) ································································································43
Unit prices (#1210) ·······························································································································44
Base quantity (#1211) ··························································································································44
PLU/subdepartment mode (#2210, 2231) ····························································································45
Sign (+/-) and tax status (#2211, 2232) ································································································46
Alphanumeric characters (#2214) ········································································································47
Assigning of PLUs to commission groups (#2215, 2235)·····································································48
Link PLU (#2220)··································································································································49
Direct PLU key positioning (#2219) ······································································································49
6 European Article Number (EAN) or Universal Product Code (UPC) programming ·································50
EAN or UPC code·································································································································50
Add-on code ·········································································································································52
EAN/UPC programming ·······················································································································52
Department assignment (#1000) ··········································································································53
Unit prices (#1010) ·······························································································································54
Base quantity (#1011) ··························································································································54
Delete method (#2010)·························································································································55
Sign (+/-) and tax status (#2011) ··········································································································56
Alphanumeric characters (#2014) ········································································································57
Assigning of EANs to commission group (#2015) ················································································57
EAN link (#2030) ··································································································································58
Delete period for non-accessed EAN codes (#2029) ···········································································58
Programming Non-PLU code format (#2025)·······················································································59
Press code functional programming (#2035)························································································60
7 Programming for miscellaneous keys······································································································61
Programming the rate (%, e, commission) and the deduction (-) (#1310) ··································61
Programming the number of digits after decimal point for exchange keys (#2330) ·····························62
Currency description text programming (#2334) ··················································································62
Assigning the drawer number to the drawer for foreign currency (#2680) ··········································63
A limit amount (HALO) of entry (-, r, p) (#2312)········································································63
+/- sign (%, -) (#2311) ····················································································································64
Item % or subtotal % selection (%) (#2315) ·······················································································65
Percent rate limitation (%) (#2313)·····································································································65
Item â or subtotal â selection (-) (#2316) ······················································································66
3
8 Programming for the ;, Å, ( through +, and ] through ’ keys ·············································67
Functional programming (#2320) ·········································································································67
High amount lockout (HALO) for cheque change, cheque cashing, and cash in drawer (#2321)········68
High amount lockout (HALO) of entry for media keys (#2322)·····························································69
9 Programming of function text···················································································································69
Programming (#2314)···························································································································69
List of function texts······························································································································70
10 Cashier and clerk programming ··············································································································71
Cashier code (#1500) ···························································································································71
Cashier name (#1514)··························································································································72
Functional programming for cashiers (#2510)······················································································72
Clerk code (#1400) ·······························································································································73
Clerk name (#1414)······························································································································73
11 Programming various functions ···············································································································74
Programming for optional feature selection (#2616) ············································································74
Programming feed line after printing of a difference subtotal (#2615)··················································78
Programming alarm length of time with drawer opening (#2617)·························································79
Programming of logo messages (#2614) ·····························································································80
Selection of X1/Z1 and X2/Z2 reports to be printed in the stacked report sequence (#2620)··············81
Setting the time range for hourly reports (#2619)·················································································82
RS-232C channel assignment (#2690) ································································································82
Barcode reader programming (#2691) ·································································································83
Secret codes to control access to the PGM1 mode, X1/Z1 mode and X2/Z2 mode
(#2630, 2631, 2632) ·····························································································································84
Functional programming for the printer (#2990) ···················································································85
Setting the AUTO key - Automatic sequencing key - (#2900) ······························································86
12 Reading stored programs ························································································································87
Program details and procedures for their reading ················································································87
Sample printouts···································································································································88
13 Training mode··········································································································································94
READING (X) AND RESETTING (Z) OF SALES TOTALS·················································································95
1 Summary of reading (X) and resetting (Z) reports and the key operations to obtain the reports ············95
2 Daily sales totals······································································································································98
Full reading and resetting of sales totals ······························································································98
Cashier reading and resetting ············································································································102
Clerk reading and resetting ················································································································104
Reading and resetting of hourly sales information ·············································································105
Full department reading ·····················································································································106
Individual group reading ·····················································································································107
Full group reading·······························································································································107
Reading and resetting of sales information for a range of PLUs/subdepartments ·····························108
Reading of sales information on PLUs/subdepartments associated with an individual department···109
Reading of PLUs/subdepartments whose sales amounts are zeros ··················································109
Reading of PLUs/subdepartments whose sales amounts are zeros (by associated department) ·····109
Reading of sales information for the price amount range of PLUs/subdepartments ··························109
Reading and resetting of sales information for EANs·········································································110
Reading and resetting of sales information for EANs associated with an individual department ·······111
Reading of EANs whose sales amounts are zero ··············································································111
Reading of EANs whose sales amounts are zeros (by associated department)································111
Reading of commission sales information ··························································································112
Transaction reading····························································································································112
Total in drawer reading·······················································································································112
Reading and resetting of a stacked report··························································································113
Deleting of non-accessed EANs·········································································································113
4
3 Periodic consolidation····························································································································114
Generality ···········································································································································114
Reading and resetting of daily net totals ····························································································115
Reading and resetting of a stacked report··························································································115
COMPULSORY CASH/CHEQUE DECLARATION ···························································································116
PROGRAMMING FOR EURO ···························································································································118
Automatic modification of register system for introduction of EURO··················································119
Optional programming for the introduction of EURO··········································································120
OVERRIDE ENTRIES ········································································································································121
CORRECTION AFTER FINALIZING A TRANSACTION (AFTER GENERATING A RECEIPT)······················122
FOR THE OPERATOR
PRIOR TO ENTRIES ·········································································································································123
1 Preparations for entries ·························································································································123
Receipt and journal paper rolls···········································································································123
Receipt ON/OFF function ···················································································································123
Cashier and clerk assignment ············································································································123
2 Error warning ·········································································································································124
ENTRIES ····························································································································································125
1 Item entries ············································································································································125
Single item entries ······························································································································125
Repeat entries ····································································································································126
Multiplication entries ···························································································································127
Successive multiplication entries········································································································128
Split-pricing entries ·····························································································································129
Single item cash sale (SICS)/single item finalize (SIF) entries···························································130
Link PLU/EAN link entries ··················································································································130
EAN learning function·························································································································131
Price inquiry (view) function (for EANs)······························································································132
Price change function (for EANs) ·······································································································133
2 Displaying subtotals·······························································································································135
Normal subtotal ··································································································································135
Difference subtotal (Differ ST) ············································································································135
3 Finalization of transaction ······················································································································136
Cash or cheque tendering ··················································································································136
Mixed tendering (cheque + cash) ·······································································································136
Cash or cheque sale that does not need any tender entry·································································136
Credit sale ··········································································································································137
Mixed-tender sale (cash or cheque tendering + credit tendering) ······················································137
4 Computation of VAT (Value Add Tax)/tax ·····························································································137
VAT/tax system ··································································································································137
VAT shift entries ·································································································································139
5 Auxiliary entries ·····································································································································139
Percent calculations (premium or discount) ·······················································································139
Deduction entries································································································································140
Refund entries ····································································································································140
Printing of non-add code numbers ·····································································································141
6 Payment treatment ································································································································141
Currency exchange ····························································································································141
Received on account entries ··············································································································142
Paid out entries···································································································································142
No sale (exchange) ····························································································································143
Cashing a cheque·······························································································································143
7 Automatic sequencing key (` key) entries··························································································143
5
CORRECTION ···················································································································································144
1 Correction of the last entry (direct void)·································································································144
2 Correction of the next-to-last or earlier entries (indirect void)································································144
3 Subtotal void ··········································································································································145
4 Correction of incorrect entries not handled by the direct or indirect void function ·································145
SPECIAL PRINTING FUNCTIONS····················································································································146
1 Copy receipt printing······························································································································146
2 Guest check copy ··································································································································147
3 Printing of header and footer graphic logos···························································································147
OVERLAPPED CASHIER ENTRY ····················································································································148
OPERATOR MAINTENANCE ···························································································································149
1 In case of power failure ·························································································································149
2 In case of printer error ···························································································································149
3 Thermal printing·····································································································································149
Cautions in handling the printer··········································································································149
Cautions in handling the recording paper (thermal paper) ·································································150
4 Paper roll near-end sensing function (only for the journal paper) <option>···········································150
5 Installing and removing the paper roll····································································································151
Recording paper specifications ··········································································································151
Installing the paper roll ·······················································································································151
Removing the paper roll ·····················································································································153
Removing a paper jam ·······················································································································154
6 Cleaning the print head ·························································································································155
7 Removing the till and the drawer ···········································································································156
8 Opening the drawer by hand ·················································································································156
9 Installing the fixing angle bracket ··········································································································157
10 Before calling for service ·······················································································································158
Error code table ··································································································································158
LIST OF OPTIONS ············································································································································159
SPECIFICATIONS ·············································································································································160
6
EXTERNAL VIEW
Front view
Customer display (Pop-up type)
Printer cover
Receipt paper
Operator display
Journal window
Mode switch
Keyboard
RS-232C connectors
Drawer lock
Drawer
Rear view
7
PRINTER
The printer is a receipt/journal dual station type thermal printer, and therefore it does not require any type of ink
ribbon or cartridge. The average life of the printer is approximately 5 million lines.
When removing the printer cover, lift up its rear. When
installing the printer cover, hook it on the pawls on the
cabinet and shut it.
Your register is shipped with the print head release lever
held by a white retainer in the lifted up position. Be sure to
remove this retainer (see the figure at the right) and push
down the print head release lever before you use the
register.
Retainer
Take-up spool
Paper roll location
Paper chute
Print head
release lever
Print head release lever
The print head can be lifted by the green lever on the right side of the printer. Pulling the lever forward lifts the
print head up. If the paper becomes jammed and you need to move the head farther forward, you can pull the
lever even further toward you and proceed with the removal of the jammed paper.
Note
8
Do not attempt to remove the paper roll with the head in the down position. This may result in
damage to the printer and print head.
KEYBOARD
1 Standard keyboard layout
PLU/ EAN AMT
SUB
#
RECEIPT JOURNAL
RCPT
Note
CL
NS
5
10
15
20
7
8
9
4
9
14
19
4
5
6
3
8
13
18
VAT CASH
#
EX1
EX2
CR1
CR2
CH1
CH2
%1 PO RA
AUTO
1
1
2
3
2
7
12
17
ST
%2 RF
AUTO
2
0
00
•
1
6
11
16
TL
All the keys but the receipt paper feed and journal paper feed keys can be re-positioned. If you
want to change the layout, consult your dealer.
RECEIPT
Receipt paper feed key
JOURNAL
Journal paper feed key
0
#
CASH
#
RCPT
Non-add code key
Cashier code entry key
Receipt print key
Discount key
Numeric keys
9
INQ
AUTO
1
00
Automatic sequencing 1 and 2 keys
AUTO
2
•
Decimal point key
%1
Percent 1 and 2 keys
Multiplication/split-pricing key
%2
CL
Clear key
NS
No-sale key
RA
Received-on-account key
PO
Paid-out key
RF
Refund key
1
Department keys
20
PLU/
SUB
Price lookup/subdepartment key
AMT
Amount entry key
EAN
EAN code entry key
EX1
INQ
EAN inquiry key
EX2
VAT
Value added tax key
Void key
Foreign currency exchange
1 and 2 keys
9
CR3
CR1
Credit 3 and 4 keys
Credit 1 and 2 keys
CR2
CR4
CA2
CH1
Cash total 2 key
Cheque 1 and 2 keys
EX3
CH2
ST
Subtotal key
EX4
TL
Total (cash total) key
CH3
Numeric key
CH4
Foreign currency exchange
3 and 4 keys
Cheque 3 and 4 keys
000
VAT
SHIFT
21
Department keys
DIFFER
ST
Value added tax shift key
Difference subtotal key
50
1/2
1/2 key
%3
CLERK
#
Percent 3 and 4 keys
Clerk code entry key
%4
1
2
Direct price lookup/subdepartment keys
Discount 2 through 4 keys
68
4
GC
COPY
Department code entry key
NON
DELETE
Non delete key
PRICE
CHANGE
Price change key
REPEAT
Repeat entry key
Guest check copy key
AUTO
3
Automatic sequencing
3 through 10 keys
AUTO
10
RA2
Received-on-account 2 key
PO2
Paid-out 2 key
Note
DEPT
#
The standard keyboard is not equipped with those keys that are marked with (
).
2 Standard key number layout
These key numbers are used for positioning of department keys and direct PLU keys. Refer to pages 41 and 49.
This layout can be changed by your dealer.
10
5
10
15
20
4
9
14
19
3
8
13
18
2
7
12
17
1
6
11
16
KEYS AND SWITCHES
1 Mode switch and mode keys
The mode switch can be operated by inserting one of the three supplied mode keys - manager (MA),
submanager (SM), and operator (OP) keys. These keys can be inserted or removed only when the switch is in
the “REG” or “ ” position.
Operative range
• Manager key (MA)
• Submanager key (SM)
MA
P
SM
MA
O
SM
REG
OP X / Z
MGR
X1/Z1
PGM1
X2/Z2
PGM2
• Operator key (OP)
The mode switch has these settings:
OP
:
This mode locks all register operations.
No change occurs to register data.
OP X/Z: This setting allows cashiers/clerks to take X or Z reports for their
sales information. (This setting may be used only when your
register has been programmed for “OP X/Z mode available” in the
PGM2 mode.) And it can be used to toggle receipt state “ON” and
“OFF” by pressing the q key.
REG:
For entering sales
PGM1: To program those items that need to be changed often: e.g., unit prices of departments, PLUs or
EANs, and percentages
PGM2: To program all PGM1 items and those items that do not require frequent changes: e.g., date, time, or
a variety of register functions
MGR:
For manager's and submanager's entries
The manager can use this mode to make entries that are not permitted to be made by cashiers - for
example, after-transaction voiding and override entry.
X1/Z1: To take the X/Z report for various daily totals
X2/Z2: To take the X/Z report for various periodic (weekly or monthly) consolidation
2 Drawer lock key
SK1-1
This key locks and unlocks the drawer. To lock it, turn 90 degrees counterclockwise. To unlock it, turn 90
degrees clockwise.
11
DISPLAYS
Operator display
Customer display (Pop-up type)
PLU/SUB
DEPT
REPEAT
RCPT
OFF
Cashier/clerk code
CID sentinel indicator
Amount:
Appears in the far-right eight (max.) positions.
Cashier code:
Appears in the second and third positions (two digits).
Clerk code:
Appears in the second and third positions (two digits) with “C” in the fifth position.
Number of repeats for repetitive registrations:
The number of repeats is displayed, starting at “2” and incremented with each repeat.
When you have registered ten times, the display will show “0.”
Example: (2 → 3 → 4 ..... 9 → 0 → 1 → 2 ... )
Receipt function status:
The indicator “_” appears in the ninth position when the receipt function is put in the OFF
status.
Time:
Appears in the second to sixth positions (using 24-hour format) in the OP X/Z, REG, or
MGR mode. In the REG, or MGR mode, press the = key to display the time.
Machine state symbols
:
Appears in the tenth place during programming.
:
Appears in the tenth place when an error is detected.
– (Floating): Appears when a minus department, PLU/subdepartment or EAN entry is made or when a
discount, refund, or void entry is made.
:
Appears in the tenth place when the subtotal is displayed or when the amount tendered is smaller
than the sale amount.
:
Appears in the tenth place when the [ through ” key is pressed to calculate a subtotal in
foreign currency.
:
Appears in the tenth place when a transaction is finalized by pressing the ;, Å, ( through
+, or ] through ’ key.
:
Appears in the tenth place when the change due amount is displayed or when the cash/cheque
declaration is compulsory.
:
Appears in the tenth place when the ? key is pressed in the MGR mode, indicating the entry into
the VOID mode. While your register is in the VOID mode, this symbol continues to be in the
display except when department codes, PLU codes or subtotals are displayed. Also appears
when a subtotal void is made.
:
Appears right below the tenth place when the cash in drawer amount exceeds a programmed
sentinel amount. The sentinel check is performed for the total cash in drawer.
Also appears right below the eighth place when the VAT shift is effective.
12
FOR THE MANAGER
PRIOR TO PROGRAMMING
1 General instructions
This chapter illustrates how to program your cash register.
All the programming items can be programmed by the Job-Code-Based Programming described later.
However, your machine allows you to program some items using the Direct Programming, which does not
require you to enter the job code.
Job-Code-Based Programming
Simplified procedure
XXXX
≈
.
Data entry
;
(Job code)
Direct Programming
Sample procedure
-
Data entry
;
(Object key)
2 How to program alphanumeric characters
You can program alphanumeric characters for departments, PLUs, EANs functions and so on in the character
entry mode.
There are two ways for programming characters: using character keys on the keyboard and entering character
codes with numeric keys on the keyboard.
Using character keys on the keyboard
Enter a character according to the position of the figure shown below.
[Ex.]
To enter the letter “#”, press é í
í
To enter the upper-case letter “K”, press í
To enter the lower-case letter “k”, press
Óí
13
• Numerals, letters and symbols are programmable simply by pressing the corresponding keys.
• Characters may only be entered in single size or in double size. By default, the single-size character mode
is selected. To enter a character in double size, press the Î key before you enter the corresponding
character.
Example
To program the word “SHARP” in double size, do the following key-in.
ÎSÎHÎAÎRÎP
• Letters of alphabets “A” through “Z”, “Ø” and “Æ”are possible to be entered in lower case or in upper case. By
default, the upper-case letter mode is selected. To enter a character in lower case, press the Ó key
before you enter the character. To return to the upper-case letter mode, press the Ó key again.
Example
To program the word “Sharp”, do the following key-in.
SÓHARP
• Symbols and special letters are programmable by using the é key. To enter a character, press the é
key before you enter the corresponding character.
Example
To program letters “# Ä Å” with the letter “#” being double size
Îé=éêAéëA
Editing the characters
You can edit the characters you entered. Pressing a character key replaces the current character with a new
one. To edit the characters, use the  key.
: Backs up the cursor, erasing the character to the left.
Entering character codes
• Numerals, letters and symbols are programmable by entering character codes and the º key. See the
alphanumeric character code table on the next page. In this way, you can program characters other than the
characters on the programming key sheet.
XXX
º
XXX: Character code (3 digits)
• Double-size characters can be made by entering the character code 253.
Example
To program the word “SHARP” with the letter “S” being double size
253
º 083 º 072 º 065 º 082 º 080 º
S
14
H
A
R
P
Alphanumeric character code table
Code Character
091
Ä
092
Ö
093
Ü
094
^
095
_
096
’
097
a
098
b
099
c
100
d
101
e
102
f
103
g
104
h
105
i
106
j
107
k
108
l
109
m
110
n
111
o
112
p
113
q
114
r
115
s
116
t
117
u
118
v
119
w
120
x
121
y
122
z
123
{
124
|
125
}
126
ß
127
¢
128
!!
129
1
130
2
131
3
132
4
1/2
133
F/T
134
←
135
Code Character
136
→
137
138
139
140
141
F
142
T
↓
143
ç
144
°
145
¿
146
Ù
147
à
148
Æ
149
ø
150
Å
151
152
¤
é
153
è
154
Pt
155
i
156
Ñ
157
ò
158
£
159
¥
160
161
°
162
163
164
.
165
Á
177
Í
178
A
180
a
181
E
182
e
183
I
184
i
185
186
U
u
187
N
188
.
n.
189
190
C
191
S
C
192
.
▲
Code Character
046
.
047
/
048
0
049
1
050
2
051
3
052
4
053
5
054
6
055
7
056
8
057
9
058
:
059
;
060
<
061
=
062
>
063
?
064
@
065
A
066
B
067
C
068
D
069
E
070
F
071
G
072
H
073
I
074
J
075
K
076
L
077
M
078
N
079
O
080
P
081
Q
082
R
083
S
084
T
085
U
086
V
087
W
088
X
089
Y
090
Z
▲
Code Character
001
á
002
â
003
ê
004
î
005
ì
006
í
007
ô
008
ó
009
û
010
ú
011
œ
012
u
´´
013
ú
014
o
´´
015
ó
016
017
018
019
¨
020
021
022
023
024
025
026
027
´´
028
U
029
Ú
´´
030
O
031
Ó
032
(space)
033
!
034
”
035
#
036
$
037
%
038
&
039
’
040
(
041
)
042
043
+
044
,
045
-
Code Character
.
193
.I
194
G
195
S.
196
G
..
197
g
198
K.
199
k.
L
200
l
201
202
Z
203
D
204
d
205
C
206
c
207
P
208
209
e
210
s
211
c
212
z
213
y
214
.
u
215
n
216
217
218
r
219
224
§
225
Ø
226
227
↑
228
]
229
[
230
231
”
ä
232
ö
233
ü
234
æ
235
å
236
É
237
ñ
238
*(DC)
253
✱
✱
(DC): Double-size character code
15
PROGRAMMING
Your machine allows you to program in two modes: PGM1 and PGM2. The PGM1 mode is for programming
those items that need to be changed often: unit prices of departments/PLUs/EANs and percentages. The
PGM2 mode is used for programming all PGM1-mode programs and those items that require less frequent
changes: date, time, tax rate, and the functions of each key. We describe below the programming or setting
procedures of various items.
Program every item necessary for your store following the appropriate procedures.
* To set the mode switch to the PGM1 position, use the manager or submanager key; and to set to the PGM2
position, use the manager key.
Preparations for Programming
1.
2.
3.
4.
Plug your machine into a standard wall outlet.
Put the manager or submanager key in the mode switch and turn it to the PGM1 or PGM2 position
depending upon the programming you are about to do.
Check to see whether both journal and receipt rolls are present in the machine. If they are missing, install
journal and receipt paper rolls correctly referring to the procedure in “4. Installing and removing the paper
roll” under “OPERATOR MAINTENANCE”.
Program necessary items into your machine.
Direct Programming
1 Setting the date and time
Date
PGM 2
Enter the day (one or two digits), month (two digits), and year (two digits) in this sequence.
Procedure
XXXXXX
Date (five or six digits)
Example
=
August 26, 2001
Key operation
Print
260801 =
Date
16
Time
PGM 2
Set the time using the 24-hour format. For example, when the time is set to 2:30 AM, enter 230; and when it is
set to 2:30 PM, enter 1430. Once you set the time, the internal clock unit will continue to run as long as the
built-in battery is alive and update the date (day, month, year) properly.
Procedure
=
XXXX
Time (max. four digits)
Example
Setting the time as 2:30 PM (14:30)
Key operation
Print
1430 =
Time
2 Programming for departments
Your machine is equipped with 20 standard departments and up to 50 optional departments.
Your machine allows you to perform the following programming for each department:
Unit price
PGM 1
PGM 2
Procedure
*1
XX
Dept. code
à
To keep the current setting
Department
key
*2
Unit price
:
;
To program for the following dept.
To program for another dept.
*1 Department code: 1 to 50
*2 Unit price: max. six digits (9999.99)
Example
Programming the unit price 10.00 for department 1
1
01
0.00
1000
01
1000
Press the : key to program this setting.
:
02
0.00
Press the ; key to finalize the programming
and generate a programming report.
;
1.
Press the department 1 key.
• The current unit price will be displayed.
2.
Enter the unit price “1000.”
3.
4.
0.00
17
Print
Dept. code
Unit price
Functional selection
PGM 2
Procedure
To keep the current setting
*1
XX
àà
*2
ABCDEFGHIJ
≈
;
Dept. code
To program for the following dept.
Department
key
Department
key
*1
à
XX
Dept. code
c
To program for
another dept.
Department
key
*1 Department code: 1 to 50
*2 Item:
A
Always enter 0.
B
VAT6 or TAX6
C
D
E
F
G
H
I
J
18
Selection:
No
Yes
VAT5 or TAX5
No
Yes
VAT4 or TAX4
No
Yes
VAT3 or TAX3
No
Yes
VAT2 or TAX2
No
Yes
VAT1 or TAX1
No
Yes
Normal/SICS (Single Item Cash Sale)/ Normal
SIF (Single Item Finalization)
SICS
SIF
Significant digit for HALO
Number of zeros to follow the significant digit for HALO
Entry:
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
2
1 through 9
0 through 8
Note
Tax status
• The tax system of your machine has been factory–set to automatic VAT1–6. If you desire to
select any of automatic tax 1–6, manual VAT1–6, manual VAT1, manual tax 1–6, and the
combination of the automatic VAT 1–3 and the automatic tax 4–6, consult your dealer.
• When the combination of the automatic VAT1–3 and automatic tax 4–6 system is selected, one of
the VAT1(G), VAT2(F) and VAT3(E) can be selected in combination with tax 4–6.
Example: BCDEFG= 100100, 110100, 111010
Normal department/SICS (Single Item Cash Sale) / SIF (Single Item Finalization)
• If an entry of a department programmed for SICS is made first, the sale will be finalized as soon
as the department key is pressed. If the entry is made after entering a department not
programmed for SICS, the sale will not be finalized until the ; key is pressed.
• Whenever a sale is made to a department set for SIF, the sale is finalized as soon as the
department key is pressed.
HALO (High Amount Lockout)
• You can set an upper limit amount (HALO) for each department. The limit is effective for the
REG-mode operations and can be overridden in the MGR mode.
• IJ is the same as I x 10 J.
For example, presetting 14 (100.00) here means that amount entries of up to 100.00 are allowed
in the REG mode. When you preset 18, however, the upper limit amount is 999999.99.
Example
Programming for department 4 as follows: A=0, B=0, C=0, D=0, E=0, F=0, G=1, H=0, I=9 and
J=5.
ABCDEFGH I J
44
1.
Press the department 4 key twice.
• The current parameter setting will be displayed.
2.
Set the parameters as follows:
• You can change the value at the blinker.
Go to the desired position with the following keys:
........Moves the blinker to the right.
0000000018
º.......Moves the blinker to the left.
0000000018
• Enter the figure.
0000000018
➞
➞
0000000018
0000000018
0000001095
0000001095
3.
Press the ≈ key to program this setting.
≈
0000000018
4.
Press the ; key to finalize the programming
and generate a programming report.
;
0.00
Print
Taxable 1
HALO limit
Normal dept.
19
3 Price lookup (PLU) programming
A PLU code can be up to six digits (free code).
Unit price
PGM 1
PGM 2
Procedure
Direct PLU
key
To keep the current setting
ß
XXXXXX
:
*Unit price
;
PLU code
*Unit price: max. six digits (9999.99)
Example
Programming the unit price 1.25 for PLU code 1
1.
Enter the PLU code “1” and press the ß key.
1ß
000001
0.00
2.
Enter the unit price “125.”
125
000001
125
3.
Press the : key to program this setting.
:
000002
0.00
4.
Press the ; key to finalize the programming
and generate a programming report.
;
0.00
Print
PLU code
Unit price
Functional selection
PGM 2
Procedure
To keep the current setting
XXXXXX
ßß
*
ABCDEFGH
≈
PLU code
Direct PLU
key
Direct PLU
key
XXXXXX
ß c
PLU code
Direct PLU
key
20
;
* Item:
A
Sign (plus/minus)
B
VAT6 or TAX6
C
VAT5 or TAX5
D
VAT4 or TAX4
E
VAT3 or TAX3
F
VAT2 or TAX2
G
VAT1 or TAX1
H
Mode
Note
Selection:
Plus
Minus
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
Prohibit mode
Subdepartment mode
PLU mode
PLU/subdepartment mode
Delete mode
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
2
3
4
Sign (plus/minus)
The function of every PLU/subdepartment varies according to the combination of its sign and the
sign of its associated department as follows:
Department
+
–
+
–
Sign
Function of PLU/subdepartment
PLU/
subdepartment
+
–
–
+
Serves as a normal plus PLU/subdepartment
Serves as a normal minus PLU/subdepartment
Accepts store coupon entries, but not split-pricing entries
Not valid; not accepted
Tax status
• The tax system of your machine has been factory–set to automatic VAT1–6. If you desire to
select any of automatic tax 1–6, manual VAT1–6, manual VAT1, manual tax 1–6, and the
combination of the automatic VAT 1–3 and the automatic tax 4–6, consult your dealer.
• When the combination of the automatic VAT1–3 and automatic tax 4–6 system is selected, one of
the VAT1(G), VAT2(F) and VAT3(E) can be selected in combination with tax 4–6.
Example: BCDEFG= 100100, 110100, 111010
• A PLU not programmed for any of these tax statuses is registered depending on the tax status of
the department which the PLU belongs to.
Mode parameter
• PLU mode: Allows a PLU entry to be made by entering an assigned PLU code and depressing
the ß key.
• Subdepartment mode: Allows a subdepartment entry to be made by entering a unit price,
pressing the å key, assigned PLU code and then pressing the ß key.
• PLU/subdepartment mode: Allows PLU entries to be made in both the PLU and subdepartment
modes.
• Delete mode: Deletes program data for each PLU.
• Prohibit mode: Prohibits the entry of any assigned PLU code. This mode does not clear the
PLU/subdepartment program data.
21
Example
1.
Programming for PLU code 1 as follows: A=0, B=0, C=0, D=0, E=0, F=0, G=1, and H=2
ABCDEFGH
Enter the PLU code “1”
and press the ß key twice.
1ß
ß
P
00000002
00000012
P
00000012
P
00000002
2.
Set the parameters A to H.
•You can go to the desired position with the º
or . key.
3.
Press the ≈ key to program this setting.
≈
4.
Press the ; key to finalize the programming
and generate a programming report.
;
0.00
Print
Taxable 1
PLU mode
PLU assignment to departments
PGM 1
PGM 2
Procedure
To delete the entered PLU
?
To keep the current setting
: à
XXXXXX
Associated dept. code
(1 to 50)
*
Department key
ß ßß
or
;
PLU code
Direct PLU
key
Direct PLU
key
XXXXXX
Direct PLU
key
ß c
PLU code
Direct PLU key
*Department key to be associated with the entered PLU
Note
• The following functions of the PLU depend on the programming for its associated department:
• Grouping (Group 1 through 14)
• SICS (Single Item Cash Sale)/SIF (Single Item Finalization)/Normal
• HALO (high amount lockout)
Example
1.
2.
22
Assigning PLU codes 1 and 2 to department 2
Enter the PLU code “1”
and press the ß key three times.
Press the department 2 key to assign
PLU code 1 to department 2.
1ß
ßß
2
000001
01
000002
01
3.
4.
Press the department 2 key to assign
PLU code 2 to department 2.
2
Press the ; key to finalize the programming
and generate a programming report.
;
000003
01
0.00
Print
Associated
dept.
4 European Article Number(EAN)/Universal Product Code(UPC) programming
Unit price
PGM 1
PGM 2
Procedure
Scan EAN code
Ä
EAN code
(max.13 digits)
To keep the current setting
Û
*Unit price
:
;
*Unit price: max. six digits (9999.99)
Note
• The entry of a EAN (or UPC) code through the scanner is indicated by Ä.
Example
1.
Programming the unit price 2.50 for EAN code 5012345678900.
Scan the EAN code,
or enter the EAN code “5012345678900”
and press the Û key.
Ä
or
5012345678900 Û
P
0.00
2.
Enter the unit price “250.”
250
P
250
3.
Press the : key to program this setting.
:
P
0.00
4.
Press the ; key to finalize the programming
and generate a programming report.
;
0.00
23
Print
EAN code
Unit price
Functional selection
PGM 2
Procedure
To keep the current setting
Scan EAN code
Ä
EAN code
(max.13 digits)
Û
ÛÛ
Ä
* Item:
A
Sign (plus/minus)
B
VAT6 or TAX6
C
VAT5 or TAX5
D
VAT4 or TAX4
E
VAT3 or TAX3
F
VAT2 or TAX2
G
VAT1 or TAX1
H
Delete method
(To erase from the EAN file)
Û
Selection:
Entry:
Plus
0
Minus
1
No
0
Yes
1
No
0
Yes
1
No
0
Yes
1
No
0
Yes
1
No
0
Yes
1
No
0
Yes
1
Delete in non-accessed EAN
0
deleting job (#105 in Z1 mode)
Inhibit to delete in non-accessed
1
EAN deleting job (#105 in Z1 mode)
Delete now
4
Sign (plus/minus)
The function of every EAN varies according to the combination of its sign and the sign of its
associated department as follows:
Sign
Department
+
–
+
–
24
;
Scan EAN code
EAN code
(max.13 digits)
Note
≈
*A B C D E F G H
Function of EAN
EAN
+
–
–
+
Serves as a normal plus EAN
Serves as a normal minus EAN
Accepts store coupon entries, but not split-pricing entries
Not valid; not accepted
Tax status
• The tax system of your machine has been factory–set to automatic VAT1–6. If you desire to
select any of automatic tax 1–6, manual VAT1–6, manual VAT1, manual tax 1–6, and the
combination of the automatic VAT 1–3 and the automatic tax 4–6, consult your dealer.
• When the combination of the automatic VAT1–3 and automatic tax 4–6 system is selected, one of
the VAT1(G), VAT2(F) and VAT3(E) can be selected in combination with tax 4–6.
Example: BCDEFG= 100100, 110100, 111010
• An EAN code not programmed for any of these tax statuses is registered depending on the tax
status of the department which the EAN code belongs to.
Delete method
• When you select “delete now”, the programmed data of the EAN code you specified is deleted
with this programming.
• When you select “Delete in non-accessed EAN deleting job”, you can delete EANs that has not
been accessed during the period that is programmed in the job #2029 with the execution of EAN
deleting job (#105 in Z1 mode).
Example
1.
Programming for EAN code 5012345678900 as follows: A=0, B=0, C=0, D=0, E=0, F=0, G=1,
and H=1.
Scan the EAN code and press the Û key,
or enter the EAN code “5012345678900”
and press the Û key twice.
ÄÛ
or
5012345678900 Û
ABCDEFGH
Û
P
00000000
00000011
P
00000011
P
0.00
2.
Set the parameters A to H.
•You can go to the desired position with the º
or . key.
3.
Press the ≈ key to program this setting.
≈
4.
Press the ; key to finalize the programming
and generate a programming report.
;
0.00
Print
Delete method
(Inhibit to delete by job#105 in Z1mode)
In case of “delete”, no mark is printed.
Taxable 1
When “delete now” is selected:
25
EAN assignment to departments
PGM 1
PGM 2
Procedure
To delete the entered EAN code
?
To keep the current setting
: à
Associated dept. code
(1 to 50)
Scan EAN code
Ä
EAN code
(max.13 digits)
ÛÛ
Û ÛÛ
*
or
;
Department key
Scan EAN code
Ä
Û
EAN code
(max.13 digits)
*Department key to be associated with the entered EAN code
Note
• The following functions of the EAN code depend on the programming for its associated
department:
• Grouping (Group 1 through 14)
• SICS (Single Item Cash Sale)/SIF (Single Item Finalization)/Normal
• HALO (high amount lockout)
Example
1.
2.
3.
Assigning EAN code 5012345678900 to department 2
Scan the EAN code and press the Û key twice,
ÄÛÛ
or enter the EAN code “5012345678900”
or
and press the Û key three times.
5012345678900 Û
Press the department 2 key to assign
EAN code 5012345678900 to department 2.
2
Press the ; key to finalize the programming
and generate a programming report.
;
ÛÛ
01
P
0.00
0.00
Print
Associated
dept.
26
P
5 Programming for discount keys
Deduction amount (-)
PGM 1
PGM 2
Procedure
-
To keep the current setting
* Deduction amount
:
;
≠
*Deduction amount: 0 - 999999
Example
Assigning “10.00” to the - key
1.
Press the - key.
-
001
0.00
2.
Enter the deduction amount “1000.”
1000
001
1000
3.
Press the : key to program this setting.
:
001
10.00
4.
Press the ; key to finalize the programming
and generate a programming report.
;
0.00
Print
Deduction
amount
27
High amount lockout (HALO) and +/- sign (-)
PGM 2
Procedure
--
To keep the current setting
≈
*A B C
;
≠≠
* Item:
A
Sign (plus/minus)
B
C
Note
Selection:
Plus
Minus
Entry:
0
1
1 through 9
0 through 8
Significant digit for HALO
Number of zeros to follow the significant digit for HALO
HALO (High Amount Lockout)
BC is the same as B x 10 C.
For example, presetting 14 (100.00) here means that amount entries of up to 100.00 are allowed in
the REG mode. When you preset 18, however, the upper limit amount is 999999.99.
Example
Programming for the - key as follows: A=1, B=1, and C=3
ABC
1.
Press the - key twice.
--
001
118
2.
Set the parameters A to C.
•You can go to the desired position with the º
or . key.
113
001
113
3.
Press the ≈ key to program this setting.
≈
001
113
4.
Press the ; key to finalize the programming
and generate a programming report.
;
0.00
Print
HALO limit
28
6 Programming for percent keys
Percent rate (%)
PGM 1
PGM 2
Procedure
∞
•
To keep the current setting
* Percent rate
:
;
* Percent rate: 0.00 - 100.00
Note
You must use a decimal point when setting percentage rates that are fractional.
Example
Assigning 10.25% to the ∞ key
Key operation
∞ 10 .
Print
25 :
;
Percent rate
Sign (+/-) (%)
PGM 2
Procedure
∞∞
••
To keep the current setting
≈
*A
* Item:
A
Sign (plus/minus)
Example
;
Selection:
Plus (premium)
Minus (discount)
Entry:
0
1
Programming minus sign for the ∞ key
Key operation
Print
∞ ∞1≈
;
Discount
29
7 Programming for exchange keys
Currency exchange rate (e)
PGM 1
PGM 2
Procedure
To keep the current setting
[
through
“
* Exchange rate
:
;
* Currency exchange rate: 0.000000 - 999.999999
Note
You must use a decimal point when setting conversion rates that are fractional.
Example
Assigning 0.6068 to the [ key
Key operation
Print
[ 0 . 6068 :
;
Exchange
rate
8 Programming for the Å , r , p , ' and î keys
High amount lockout (HALO) (Å
, r , p , ' and î)
PGM 2
Procedure
To keep the current setting
Corresponding key
*A B
≈
;
* AB is the same as A x 10B
A: Significant digit (1 through 9)
B: Number of zeros to follow the significant digit (0 through 8)
Example
Programming a HALO limit of 1000.00 (15) for the } key
Key operation
Print
} 15 ≈
;
HALO limit
30
9 Programming the tax rate
Tax rate
PGM 2
Procedure
When the lowest taxable amount is zero
◊
*A
≈
**Sign and tax rate
≈
Lowest taxable amount
1 -6
;
max. five digits:
0.00 to 999.99
To delete
:
* A: Enter a corresponding tax rate number. For example, when you program a tax rate as tax rate 1, enter “1”,
and when you program it as tax rate 6, enter “6”.
**
Sign and tax rate: XYYY.YYYY
Tax rate= 0.0001 to 100.0000
Sign -/+ = 1/0
Note
• The lowest taxable amount is valid only when you select add on tax system. If you select VAT
(Value added tax) system, it is ignored.
• If you make an incorrect entry before pressing the second ≈ key in programming a tax rate,
cancel it with the c key; and if you make an error after pressing the second ≈ key, cancel it
with the : key. Then program again from the beginning.
• If you select VAT system, the sign which you program is ignored.
Example
Programming the tax rate (+4%) as tax rate 2 with lowest taxable income as 0.12
1.
Press the ◊ key.
P
0.00
Enter the tax rate “2”.
◊
2≈
2.
2
0.00
3.
Enter the tax rate “+4%.”
4≈
2
0.00
4.
Enter the lowest taxable amount “12.”
12
2
12
5.
Press the ; key to finalize the programming
and generate a programming report.
;
0.00
Print
Tax rate : 4%
Lowest taxable
amount
Tax rate 2
31
Job-Code-Based Programming
This section illustrates how to program items using job codes. Using job codes allows you to program a wide
variety of items in comparison with direct programming.
Start this programming by entering a corresponding job code as shown below.
2110
.
≈
All the items which can be programmed by the job-code-based programming are listed on this page and the
following, and those which can also be programmed by the direct programming are marked with the symbol
“ Direct ” that follows job codes.
Note
When setting the parameters for a job code, the digit that is blinking is the one that can be changed.
To go to the position of the parameter that you want to change, press either of the following keys :
. Moves the blinker to the right.
º Moves the blinker to the left.
1 Setting the date and time
Setting the date
PGM 2
2610
Direct
Enter day (one or two digits), month (two digits), and year (two digits) in this sequence.
Procedure
2610
.
≈
Example
Date (five or six digits)
;
Key operation
Print
2610 . ≈
260801 ;
Date
Setting the time
PGM 2
2611
Direct
Set the time using the 24-hour format. For example, when the time is set to 2:30 AM, enter 230; and when it is
set to 2:30 PM, enter 1430.
Procedure
2611
32
.
≈
Time (max. four digits)
;
Example
Key operation
Print
2611 . ≈
1430 ;
Time
2 Setting the register and consecutive numbers
Setting the register number
PGM 2
2612
When your store has two or more registers, it is practical to set separate register numbers for their identification.
You may set them in a maximum of six digits.
Procedure
To set the register number “0”
2612
.
≈
Example
Register number
(one to six digits)
;
Key operation
Print
2612 . ≈
123456 ;
Register number
Setting the consecutive number
PGM 2
2613
The consecutive number is increased by one each time a receipt is issued.
Enter a number (one to four digits) that is one less than the desired starting number.
Procedure
To begin the count from 0001
2613
.
≈
A number (one to four digits) that is one
less than the desired starting number
;
33
Example
Key operation
Print
2613 . ≈
1000 ;
Consecutive
number
3 Programming the tax rate
Tax rate
PGM 2
2711
Direct
Procedure
When the lowest taxable amount is zero
2711
.
≈
A*
1 to 6
≈
**Sign and
tax rate
≈
;
Lowest taxable
amount
max. five digits:
0.00 to 999.99
To delete
:
*A: Enter a corresponding tax rate number. For example, when you program a tax rate as tax rate 1, enter 1
and when you program it as tax rate 6, enter 6.
** Sign and tax rate: XYYY.YYYY
Tax rate= 0.0001 to 100.0000
Sign -/+ = 1/0
Example
Key operation
Print
2711 . ≈
2≈
4≈
12 ;
Tax rate : 4%
Lowest taxable
amount
Tax rate 2
Note
34
• The lowest taxable amount is valid only when you select add on tax system. If you select VAT
(Value added system), it is ignored.
• If you make an incorrect entry before pressing the third ≈ key in programming a tax rate, cancel
it with the c key; and if you make an error after pressing the third ≈ key, cancel it with the :
key. Then program again from the beginning correctly.
• If you select VAT system, the sign which you program is ignored.
4 Programming for departments
Your machine is equipped with 20 standard departments and up to 50 optional departments.
Your machine allows you to perform the following programming for each department:
Functional programming
PGM 2
2110
You can set each department for:
SICS (Single Item Cash Sale) / SIF (Single Item Finalization)
• SICS
If the first registration is to a department set for SICS, the sale is finalized as soon as the department key is
pressed. If the sale is preceded by registrations to departments not set for SICS, a sale to a department set
for SICS does not finalize and can be repeated until the ; key is pressed.
• SIF
Whenever a sale is made to a department set for SIF, the sale is finalized as soon as the department key is
pressed.
Type of unit price entry
You may select one of the following four types of unit price entry for each department.
• Open and preset
• Preset only
• Open only
• Inhibit department key
Procedure
To program for the dept. other than the following dept.
c
To keep the current setting
2110
.
≈
Dept. code
≈
*A B C D E F G
:
;
To program for the following dept.
The current
setting
is displayed.
* Item:
Selection:
A to D
E
Always enter 0.
SIF/SICS /Normal
F
G
Always enter 0.
Type of unit price entry
SIF
SICS
Normal
Open and preset
Preset only
Open only
Inhibit department key
Entry:
0
2
1
0
0
3
2
1
0
35
Example
Key operation
Print
2110 . ≈
3 ≈ 0000003 :
;
A through G
Tax status
PGM 2
2111
Direct
Assign a tax status to each department. When entries are made into taxable departments in a transaction, tax is
automatically computed according to the associated tax rate as soon as the transaction is completed.
Procedure
To program for the dept. other than the following dept.
c
To keep the current setting
2111
.
≈
Dept. code
≈
*A B C D E F G
:
;
To program for the following dept.
The current
setting
is displayed.
* Item:
Always enter 0.
VAT6 or TAX6
C
VAT5 or TAX5
D
VAT4 or TAX4
E
VAT3 or TAX3
F
VAT2 or TAX2
G
VAT1 or TAX1
Note
36
Selection:
A
B
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
0
• The tax system of your machine has been factory–set to automatic VAT1–6. If you desire to
select any of automatic tax 1–6, manual VAT1–6, manual VAT1, manual tax 1–6, and the
combination of the automatic VAT 1–3 and the automatic tax 4–6, consult your dealer.
• When the combination of the automatic VAT1–3 and automatic tax 4–6 system is selected, one of
the VAT1(G), VAT2(F) and VAT3(E) can be selected in combination with tax 4–6.
Example: BCDEFG= 100100, 110100, 111010
Example
Key operation
Print
2111 . ≈
4 ≈ 0000110 :
c 2 ≈ 0000101 :
;
Tax status
A limit amount (HALO) of entry
PGM 2
2112
Direct
You can set upper limit amounts (HALO: High Amount Lockout) for each department. The limit is effective for
the REG-mode operations and can be overridden in the MGR mode. HALO limit is represented by two figures
as follows:
Procedure
c
To keep the current setting
2112
.
≈
≈
Dept. code
*A B
:
;
The current
setting
is displayed.
* AB is the same as A x 10B.
A: Significant digit (1 through 9)
B: Number of zeros to follow significant digit (0 through 8)
For example, presetting 14 (100.00) here means that amount entries of up to 100.00 are allowed in the REG
mode. But when you preset 18, the upper limit amount is 999999.99.
Example
Key operation
Print
2112 . ≈
1 ≈ 95 :
;
HALO limit
37
Alphanumeric characters PGM 2 2114
You can program a maximum of 16 characters (item label) for each department. (However, the default setting is
for a 12-character label.)
Select the characters you want to program, referring to section “2 How to program alphanumeric characters” in
chapter “PRIOR TO PROGRAMMING”.
Procedure
c
To program spaces
2114
.
≈
Example
Character keys
(max. 16 digits)
≈
Dept. code
Key operation
:
;
Print
2114 . ≈
1≈
FRUITS :
;
Label
programmed
for dept. 1
Unit price
PGM 1
PGM 2
1110
Direct
You can program unit prices up to a maximum of six digits (9999.99). Even if a department is not programmed
to allow the entry of preset unit prices in functional programming (job 2110), the department is automatically
changed to allow the entry of preset unit prices by this programming entry.
Procedure
The current
setting
is displayed.
1110
.
≈
≈
Dept. code
Unit price
(max. six digits)
:
;
To keep the current setting
c
Example
Key operation
Print
1110 . ≈
1 ≈ 1000 :
;
38
Unit price
Commission group assignment
2115
PGM 2
Your machine allows you to assign a commission group (1-9) to each department.
Procedure
The current
setting
is displayed.
To keep the current setting
2115
.
≈
Dept. code
≈
*A
:
;
To program for the follwing dept.
c
* A: Commission group 0-9 (0 = no commission)
Example
Key operation
Print
2115 . ≈
1≈1:
c5≈2:
;
Commission
group number
39
Group number
PGM 2
2116
You can assign departments to a maximum of 14 groups (1 through 14).
This programming enables you to take group department sales reports.
Procedure
The current setting
is displayed.
To keep the current setting
2116
.
≈
≈
Dept. code
*Group no.
(1 through 14)
:
;
c
* Group number: Dept. (+)
Dept. (–)
Hash (+) dept.
Hash (–) dept.
Bottle return (+) dept.
Bottle return (–) dept.
Note
Example
1 through 9 (groups 1 through 9)
10
11
12
13
14
The standard model provides no hash dept./bottle return dept. If you need them, please consult
your dealer.
Key operation
Print
2116 . ≈
1≈1:
2:
;
40
Group no.
Department key positioning
PGM 2
2119
You can assign a department number to each key position. Each key position has a corresponding key number.
Departments may be freely selected for the number of department keys and their positions.
To assign the department to a key position, select the key number of the position.
For key number position, refer to section “2 Standard key number layout” in chapter “KEYBOARD”.
Procedure
To program for the key number other than the following key number
Cancellation
2119
.
≈
*1
≈
Key no.
(1 through 68)
*2
AB
:
;
To program for the following key number
*1 The key number placement is determined by your local Authorized SHARP Dealer.
*2 AB is a department code.
Example
Key operation
Print
2119 . ≈
1≈1:
2:
;
Key no.
Dept. code
41
5 Price lookup (PLU) programming
Your machine has two kinds of PLU registration methods.
Direct PLU registration: Accomplished by depressing item key (direct PLU key) directly.
Indirect PLU registration: Accomplished by making an entry of PLU code and pressing the ß key.
Each PLU requires you to program the following:
PLU code (six digits)
Associated department
When a PLU is associated with a department, the following functions of the PLU depend on the
programming for the corresponding department.
• Grouping (Group 1 through14)
• HALO (only for the subdepartment)
• Single item cash sale/Single item finalization
Unit price (max. six digits)
You will usually have unit prices programmed for individual PLUs as PLU preset unit prices. If you program
unit price “0” for a PLU, you can enter only the selling quantity of the PLU, i.e. the PLU can be used only as
a counter.
Base quantity for split-pricing entries - two digits
Program a base quantity for each PLU/subdepartment dedicated to split-pricing entries.
PLU, subdepartment, PLU/subdepartment, delete, or prohibit mode
• If the PLU mode (i.e. automatic preset unit price entry) is selected, individual PLU entries can be made by
entering the assigned code and depressing the ß key (or by depressing a direct PLU key without any
PLU code entry).
• If the subdepartment mode is selected, the å key must be depressed after the price entry followed by the
PLU code entry. The entry is finalized by the ß key depressed.
• If the PLU/subdepartment mode is selected, the entries in both the PLU and subdepartment modes are
available.
• If the delete mode is selected, the corresponding program data for each PLU is deleted.
• If the prohibit mode is selected, the assigned PLU code cannot be entered. This mode does not clear the
PLU/subdepartment program data.
Sign (+/-)
The function of every PLU/subdepartment varies according to the combination of its sign and its associate
department's sign as follows:
Sign
Function of PLU/subdepartment
Dept.
PLU/subdept.
+
+
Serves as a normal plus PLU/subdept.
–
–
Serves as a normal minus PLU/subdept.
+
–
Accepts store coupon entries, but not split-pricing entries.
–
+
Not valid; not accepted.
Tax status
Item label (12 characters) (option: max. 16 characters)
Commission group (1 to 9)
Link PLU
Any PLU is able to link to any other PLU (e.g. bottle deposit). However, the number of links is a maximum of
5. Even if more than 5 PLUs are linked, the sixth or higher link is not actualized.
Direct PLU key positioning
42
For some items, you can program in two ways: programming an individual PLU code and for a
range of sequential PLU codes. The procedure marked “For each PLU” shows individual PLU
programming. “For a range of PLUs” shows sequential range PLU programming.
Note
Department assignment
PGM 1
PGM 2
1200
2230
Direct
Procedure
For each PLU
The current
setting
is displayed.
.
1200
*1
≈
To keep the
current setting
≈
PLU code
*4
AB
:
;
To program for the following PLU
c
As soon as the programming is completed for one PLU, the next PLU code appears in the display.
Note
For a range of PLUs
2230
.
*2
Start PLU code
The current setting
of start PLU code
is displayed.
≈
≈
*3
End PLU code
≈
To apply the current
setting of start PLU code
to PLUs within the range
*4
AB
:
;
*1, 2, 3: 1 to 999999 (free code)
*4:
AB: Associated department code
Example
For each PLU
Key operation
Print
1200 . ≈
1≈2:
2:
PLU code
;
Associated dept.
For a range
of PLUs
Key operation
2230 . ≈
11 ≈ 20 ≈
3:
Print
PLU range
;
Associated dept.
43
Unit prices
PGM 1
1210
PGM 2
Direct
Procedure
The current setting
is displayed.
1210
.
≈
≈
PLU code
To keep the current setting
Unit price
(max. six digits)
:
;
c
Example
Key operation
Print
1210 . ≈
1 ≈ 125 :
;
Unit price
Base quantity
PGM 1
PGM 2
1211
Procedure
The current
setting
is displayed. To keep the current setting
1211
.
≈
≈
PLU code
Base q'ty
(max. 2 digits)
:
;
c
Example
Key operation
Print
1211 . ≈
2 ≈ 12 :
;
44
Base q'ty
PLU/subdepartment mode
2210
PGM 2
2231
Direct
Procedure
For each PLU
The current
setting is
displayed.
.
2210
*1
≈
To keep the current setting
≈
c
PLU code
*4
ABC
;
:
For a range of PLUs
.
2231
The current setting
of start PLU code
is displayed.
≈
*2
Start PLU code
≈
*3
End PLU code
To apply the current setting of
start PLU code to PLUs within the range
≈
*4
ABC
:
;
*1,2,3: 1 through 999999
*4: Item:
Selection:
A and B Always enter 0.
C
Mode parameter
Entry:
0
0
1
2
3
4
Prohibit mode
Subdept. mode
PLU mode
PLU/subdept. mode
Delete mode
Example
For each PLU
Key operation
Print
2210 . ≈
1 ≈ 003 :
;
3: PLU/subdept.
mode
For a range
of PLUs
Key operation
2231 . ≈
11 ≈ 20 ≈
003 :
Print
PLU range
;
3: PLU/subdept.
mode
45
Sign (+/-) and tax status
PGM 2
2211
2232
Direct
Procedure
For each PLU
The current
setting
is displayed. To keep the current setting
.
2211
≈
*1
PLU code
*4
ABCDEFG
≈
;
:
c
For a range of PLUs
.
2232
≈
*2
Start PLU code
≈
The current setting
of start PLU code
is displayed.
*3
End PLU code
≈
To apply the current setting of start
PLU code to PLUs within the range
*4
ABCDEFG
:
;
*1,2,3: 1 through 999999
*4: Item:
A
Sign (+/-)
B
VAT6 or TAX6
C
VAT5 or TAX5
D
VAT4 or TAX4
E
VAT3 or TAX3
F
VAT2 or TAX2
G
VAT1 or TAX1
Note
46
Selection:
Entry:
Minus PLU
Plus PLU
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
1
0
1
0
1
0
1
0
1
0
1
0
1
0
• The tax system of your machine has been factory–set to automatic VAT1–6. If you desire to
select any of automatic tax 1–6, manual VAT1–6, manual VAT1, manual tax 1–6, and the
combination of the automatic VAT 1–3 and the automatic tax 4–6, consult your dealer.
• When the combination of the automatic VAT1–3 and automatic tax 4–6 system is selected, one of
the VAT1(G), VAT2(F) and VAT3(E) can be selected in combination with tax 4–6.
Example: BCDEFG= 100100, 110100, 111010
• A PLU not programmed for any of these tax statuses is registered depending on the tax status of
the department which the PLU belongs to.
Example
For each PLU
Key operation
Print
2211 . ≈
2 ≈ 0000001 :
0000000 :
;
Taxable 1
For a range
of PLUs
Key operation
Print
2232 . ≈
11 ≈ 20 ≈
0000001 :
PLU range
;
Alphanumeric characters
Taxable 1
PGM 2
2214
You can program a maximum of 16 characters (item label) for each PLU or subdepartment. (However, the
default setting is for a 12-character label.) Select the characters you want to program, referring to section “2
How to program alphanumeric characters” in chapter “PRIOR TO PROGRAMMING”.
Procedure
To program spaces
2214
.
≈
≈
PLU code
Character keys
(max. 16 digits)
:
;
c
Example
Key operation
Print
2214 . ≈
1≈
MILK :
;
Label
programmed
for PLU code 1
47
Assigning of PLUs to commission groups
PGM 2
2215
2235
You can assign PLUs (or subdepartments) to commission groups.
Procedure
For each PLU
The current
setting
is displayed.
To keep the current setting
*1
.
2215
≈
PLU code
≈
:
*A
;
To program for the following PLU
c
For a range of PLUs
.
2235
≈
*2
Start PLU code
The current
setting
is displayed. To apply the current setting of start
PLU code to PLUs within the range
*3
≈
End PLU code
≈
*A
:
;
*1,2,3 : 1 through 999999
*A
: Commission group 0-9 (0=no commission)
Example
For each PLU
Key operation
Print
2215 . ≈
1≈1:
;
Commission
group number
For a range
of PLUs
Key operation
2235 . ≈
12 ≈ 14 ≈
1:
;
48
Print
PLU range
Commission
group number
Link PLU
PGM 2
2220
Procedure
Cancellation
2220
.
≈
≈
PLU code
:
Linked PLU code
;
To repeat up to 5 times
Note
• To program this function, please consult your dealer.
• PLU codes must have already been defined.
Example
Key operation
Print
2220 . ≈
21 ≈ 25 :
26 :
27 :
Linked
PLU code
;
Direct PLU key positioning
PGM 2
2219
You can assign a PLU code to each key position. PLUs may be selected for the number of direct PLU keys and
their positions. For key number positions, refer to section “2 Standard key number layout” in the chapter
“KEYBOARD”.
Procedure
Cancellation
2219
.
≈
* Key no.
(1 through 68)
≈
PLU code
:
;
To program for the following key number
To program for the key number other than the following key number
* The key number placement is determined by your local Authorized SHARP Dealer.
Example
Key operation
Print
2219 . ≈
16 ≈
1:
;
Key no.
PLU code
49
6 European Article Number (EAN) or Universal Product Code (UPC) programming
EAN or UPC code
Your machine can transact the following codes:
• UPC-A (Number system character: 0, 2, 3, 4)
• UPC-E
• EAN-8
• EAN-13
• Internal code EAN-8/EAN-13
For the codes used in-store marking, there are two types of PLU type (treated as a code like PLU code) and
Non-PLU type (price/quantity information is included in the code).
When a code is non-PLU type, the price/quantity in the code is read for sales entry (in case of quantity, “quantity
multiplys preset unit price” is processed to obtain price.)
UPC-A
• Number system character: 0 <used in the source marking>
• Number system character: 3 <used as NDC or HRI>
C
0
Maker code
Check digit
Number system character
For entry, a full 12 digits number or 11 digits number (omitting the
check digits) must be entered.
• Number system character: 2 <In-store marking Non-PLU type>
You can program the format by the job #2025.
• Number system character: 4 <In-store marking PLU type>
C
3
2
*
Item code
*
*
*
C
D
Price check digit
• UPC-E is a zero-suppressed version of UPC-A that conforms to
the UPC-E Standards. This code is used for marking small
package.
For entry, a 6 digits number or a leading zero plus 6 digits number
must be entered.
EAN-8
• Ordinary EAN-8 code (flag: neither 0 nor 2) <used in the source marking>
For entry, a full 8 digits number must be entered.
C
D
Maker code
Nation code
Item code
C
2
D
(Free format)
Program the format by the job#2025.
C
0
(Free code)
50
*
Price
UPC-E
For entry, a full 8 digits number must be entered. On the
receipt/journal, non-PLU type code is printed like 208**** (****:
price/quantity information)
D
NCD (or HRI) format
4
For entry, a full 12 digits number, 11 digits number (omitting the
(Free code)
check digit), or a leading zero plus 12 digits number must be
entered.(Any numbers are allowed for the digits marked with *,
and on the receipt/journal, non-PLU type code is printed like 2020008**** (****: price information).)
• Internal code (flag 2) <in-store marking non-PLU short type>
Program the format by the job #2025.
• Internal code (flag 0) <in-store marking PLU short type>
D
Item code
D
C
D
EAN-13
• Ordinary EAN-13 code (used in the source marking)
• Specific EAN-13 code (flag 977, 978, 979) (used in the source
marking: ISBM, ISSN)
C
Maker code
D
Item code
Nation code
For entry, you must enter a full of 13 digits number.
• Internal code (used in the in-store marking, the flag character
number: 20 through 29 and 02)
Program the format by the job# 2025.
C
Flag
02, 20-29
D
(Free format)
Program the format by the job #2025.
• EAN press code (used for press articles)
For a press article, you must use a 13 digits number EAN code plus a 2-digit or 5-digit add-on code, though
your register can register 13 digits number EAN code without an add-on code.
Note
The format for press articles is decided unique by each country. For the formats for other
countries than the ones shown below, please ask your dealer.
German type 1
Currency for price is DM. (The price is not
converted automatically according to EURO
status.)
German type 2
(EURO code - The price is coded in EURO
from January 2002)
Currency for price is EURO.
Article code
C
D (+ Add-on code)
C
D (+ Add-on code)
C
D (+ Add-on code)
Price (xx.xx)
Prefix code 434 or 439
Article code
Price (xx.xx)
Prefix code 414 or 419
United Kingdom
Currency for price is GBP.
Article code
Price (xx.xx)
Prefix code 988 or 989
France
Currency for price on the prefix code 378 is
EURO, and 379 is FFr. (The price is
converted automatically according to EURO
status.)
Sweden
Currency for price is SKr.
Note
3 7 8
S
Article code
Prefix code
D (+ Add-on code)
C
D (+ Add-on code)
Supplier code
7 3 8 8
Prefix code
C
Price (xx.xx)
Article code
Price (xxx.x)
• The availability of these press codes on your register depends on the programming (job #2035)
• Since the price in a press code is read for sales entries, and the currency is decided by the
code, note that the code you enter for sales matches your domestic currency.
51
Add-on code
UPC-A and EAN-13 may be followed by a two digits number or a five digits number as add-on code, excepting
UPC-A without a check digit plus two or five digits add-on code.
Therefore, the total number of digits enterable for sales entries are as shown below:
Code entry
No add-on code
2-digit add-on code
5-digit add-on code
UPC-A
12
14
17
UPC-A w/leading zero
13
15
18
UPC-A w/o check digit
11
–
–
UPC-E
6
–
–
EAN-8
8
–
–
EAN-13
13
15
18
Note
Your register automatically judges the add-on code in an EAN code entered from the total number
of digits and the flag.
EAN/UPC programming
Each EAN or UPC code (hereinafter referred to as EAN) requires you to program the following.
• EAN code (max. 13 digits)
• Associated department (1-50)
When an EAN is associated with a department, the following functions of the EAN depend on the
programming for the department.
• Grouping (Group 1 through14)
• HALO (only for the subdepartment)
• Single item cash sale/Single item finalization
EAN code delete method
You can program how you delete EAN codes; deleting in the programming, inhibit deleting, or deleting the
EAN codes that have not been accessed for a certain period, which can be programmed (up to 99 days)
when you execute #105 in Z1 mode.
Unit price (max. six digits)
Base quantity for split-pricing entries
Sign (+/–)
Tax status
If you do not program tax status for an EAN, the tax status of the EAN follows to the status of the associated
department.
Item label (12 characters) (option max. 16 characters)
Commission group (1-9)
EAN link
System programming for EAN function
Delete period for non-accessed EAN codes
Non-PLU code format
Type of press code
Price entry method for press code
Label of record in EAN file
52
Department assignment
PGM 1
1000
PGM 2
Direct
Procedure
The current setting
is displayed.
Scan EAN code
Ä
1000
.
Example
≈
EAN code
(max.13 digits)
Key operation
To keep the current setting
≈
Associated
dept. code
(1 to 50)
:
;
Print
1000 . ≈
5012345678900 ≈
2:
EAN code
;
Associated dept.
53
Unit prices
PGM 1
1010
PGM 2
Direct
Procedure
The current setting
is displayed.
Scan EAN code
Ä
1010
.
≈
Example
EAN code
(max.13 digits)
To keep the current setting
≈
Unit price
(max.6 digits)
Key operation
:
;
Print
1010 . ≈
5012345678900 ≈
250 :
;
Base quantity
PGM 1
PGM 2
Unit price
1011
Procedure
The current setting
is displayed.
Scan EAN code
Ä
1011
.
Example
≈
EAN code
(max.13 digits)
Key operation
To keep the current setting
≈
Base q'ty
(max.2 digits)
:
;
Print
1011 . ≈
5012345678900 ≈
5:
;
54
Base q’ty
Delete method
PGM 2
2010
Procedure
The current setting
is displayed.
Scan EAN code
Ä
2010
.
≈
EAN code
(max.13 digits)
To keep the current setting
≈
*
Delete method
:
;
* Delete method
4: Delete now
1: Inhibit to delete in non-accessed EAN deleting job (#105 in Z1 mode)
0: Delete in non-accessed EAN deleting job (#105 in Z1 mode)
With the execution of EAN deleting job, you can delete EANs that have not been accessed during the period
that is programmed in the job #2029.
Example
Key operation
Print
2010 . ≈
5012345678900 ≈
1:
;
Delete method
(Inhibit to delete by job#105 in Z1 mode)
In case of “delete”, no mark is printed.
When “delete now” is selected:
55
Sign (+/-) and tax status
2011
PGM 2
Direct
Procedure
The current setting
is displayed.
Scan EAN code
Ä
2011
*:
.
≈
EAN code
(max.13 digits)
Item:
A
Sign (+/-)
B
VAT6 or TAX6
C
VAT5 or TAX5
D
VAT4 or TAX4
E
VAT3 or TAX3
F
VAT2 or TAX2
G
VAT1 or TAX1
Note
To keep the current setting
≈
*
:
ABCDEFG
Selection:
Minus
Plus
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
;
Entry:
1
0
1
0
1
0
1
0
1
0
1
0
1
0
• The tax system of your machine has been factory–set to automatic VAT1–6. If you desire to
select any of automatic tax 1–6, manual VAT1–6, manual VAT1, manual tax 1–6, and the
combination of the automatic VAT 1–3 and the automatic tax 4–6, consult your dealer.
• When the combination of the automatic VAT1–3 and automatic tax 4–6 system is selected, one of
the VAT1(G), VAT2(F) and VAT3(E) can be selected in combination with tax 4–6.
Example: BCDEFG= 100100, 110100, 111010
• An EAN not programmed for any of these tax statuses is registered depending on the tax status
of the department which the EAN belongs to.
Example
Key operation
Print
2011 . ≈
5012345678900 ≈
0000001 :
;
Taxable 1
56
Alphanumeric characters
PGM 2
2014
You can program a maximum of 16 characters (item label) for each EAN. (However, the default setting is for a
12-character label.) Select the characters you want to program, referring to section “2 How to program
alphanumeric characters” in chapter “PRIOR TO PROGRAMMING”.
Procedure
Scan EAN code
Ä
2014
.
≈
Example
EAN code
(max.13 digits)
To keep the current setting
≈
Key operation
;
:
Character keys
(max. 16 digits)
Print
2014 . ≈
5012345678900 ≈
APPLE :
;
Item label
Assigning of EANs to commission groups
2015
PGM 2
You can assign EANs to commission groups.
Procedure
The current setting
is displayed.
Scan EAN code
Ä
2015
.
≈
EAN code
(max.13 digits)
To keep the current setting
≈
*
:
A
;
*A : Commission group 0-9 (0=no commission)
Example
Key operation
Print
2015 . ≈
5012345678900 ≈
1 :
;
Commission
group number
57
EAN link
2030
PGM 2
Procedure
Scan EAN code
Ä
2030
.
≈
EAN code
(max.13 digits)
Cancellation
≈
Linked PLU
code
;
:
* To repeat up to 5 times
* The programmed number of linked PLUs is shown on the display like “P 1”. (Incremented one every time you
program a linked PLU.)
Note
• To program this function, please consult your dealer.
• EAN code and PLU code must have been already defined.
Example
Key operation
Print
2030 . ≈
5012345678900 ≈
30 :
31 :
32 :
Linked PLU
;
Delete period for non-accessed EAN codes
PGM 2
2029
You can delete the EAN codes which have not been accessed during the period you set in this program when
you execute the job #105 in Z1 mode when you set “Delete in non-accessed EAN deleting job” in the EAN
delete method (#2010).
Procedure
To program “00”
2029
.
≈
Delete period
(1 to 99 days)
;
* When you select “00” for the period, no EAN code is deleted by the non-accessed EAN deleting job.
Example
Key operation
2029 .
60
58
Print
≈
;
Programming Non-PLU code format
2025
PGM 2
The register allows you to specify the Non-PLU code format (flag code: 2, 02, 20 -29).
The format data is as follows:
C
Flag
(02 or 20-29)
C
2
D
Free format
D
Free format
Flag
Price check digit
Field 1
Field 2
Free format area
Procedure
To delete
*1
2025
.
≈
Flag code
(max. 2 digits)
*1 Flag code: 2, 02, 20 - 29
*2 Item:
≈
*2
ABCDEF
Selection:
A
B
C
Length of field 1 (number of digits)
Length of field 2 (number of digits)
Meaning of field 1*3
D
Meaning of field 2*4
E
Price check digit used
F
TAB or decimal point of field 2 (0, 1, 2, 3)
:
;
Entry:
0-9
0-9
2
1
0
2
0
1
0
0-3
Free code
Dept. code
PLU code
Quantity
Price
Yes
No
*3: When you select Dept. code, the sales are counted up as the sales of the department (associated
department assignment is ignored.), and when you select PLU code, the sales are counted up as the sales of
the PLU code, while they are counted up as EAN sales for sales reports.
*4: When you select quantity, the sales amount is calculated as follows: quantity x unit price programmed in
#1010.
Example
P
2 0
Flag
code
C
D
PLU code
D
Price
Price check digit
(TAB2)
Key operation
Print
2025 . ≈
20 ≈
540012 :
ABCDEF
;
Flag code
59
Press code functional programming
PGM 2
2035
Procedure
The current
setting
is displayed. To keep the current setting
2035
.
≈
*1
≈
A
*2
ABC
;
:
*1 Type of prefix code
1: German type 1 (prefix code: 434/439)
2: U.K. (prefix code: 988/989)
3: France (prefix code: 378/379)
4: Sweden (prefix code: 7388)
5: German type 2 (prefix code: 414/419)
*2 Item:
A
Type of code
B
Price entry method for press code*3
C
Label of record in EAN file*3*4
Selection:
Normal EAN code
Press code
Using the encoded price
Using the EAN programmed price
in the job #1010
Compulsory
Prefix only
Prefix + article code
Entry:
0
1
0
1
2
0
1
*3: This setting is valid only when “press code” is set for item A.
*4: Select “prefix only” when you want to summarize the sales of items having press codes by category.
Select “prefix + article code” when you want to summarize the sales of items having press codes by each
item.
Example
Key operation
2035 . ≈
1≈
111 :
;
60
Print
Type of prefix
code
ABC
7 Programming for miscellaneous keys
Only function keys which you have programmed on the keyboard will allow the programming.
Programming the rate (%, e, commission) and the deduction (-)
PGM 2
1310
PGM 1
Direct
You can program percent rates, currency exchange rates, deduction amounts and commission rates.
Procedure
The current
setting is
displayed.
1310
.
*1: Function no.
1: For the - key
2: For the – key
3: For the — key
4: For the ≠ key
5: For the ∞ key
6: For the § key
7: For the ¶ key
≈
*1
Function no.
≈
8: For the • key
52: For the [ key
53: For the { key
54: For the “ key
75: For the commission sale 1
76: For the commission sale 2
77: For the commission sale 3
To keep the current setting
*2
Rate or amount
:
;
78: For the commission sale 4
79: For the commission sale 5
80: For the commission sale 6
81: For the commission sale 7
82: For the commission sale 8
83: For the commission sale 9
*2: Rate or amount
0 — 999999 (Deduction amount)
0.00 — 100.00 (% rate)
0.000000 — 999.999999 (Currency exchange rate)
0.00 — 999.99 (Commission rate)
Note
• When you introduce EURO, set the EURO conversion rate on the [ key for the period 1 and the
period 2.
• You must use a decimal point when setting percentage rates that are fractional.
Example
Key operation
Print
1310 . ≈
1 ≈ 1000 :
5 ≈ 10 . 25 :
52 ≈ 0 . 6068 :
;
Deduction
amount
Percent rate
Currency
exchange rate
61
Programming the number of digits after decimal point for exchange keys
PGM 2
Note
2330
When you introduce EURO on your register, this setting for the [ is automatically programmed by
execution of Job #800 in the X2/Z2 mode.
Procedure
2330
.
*: Function no.
52: For the [ key
53: For the { key
≈
*Function no.
≈
Number of digits after
decimal point (0-3)
:
;
54: For the “ key
55: For the ” key
Example
Key operation
Print
2330 . ≈
52 ≈
2:
;
Number of digits
after decimal point
Currency description text programming
PGM 2
2334
You can program a maximum of 4 characters for each of the [ through ” keys.
Procedure
To program spaces
2334
.
*: Function no.
52: For the [ key
53: For the { key
Example
≈
*Function no.
Character keys
(max. 4 digits)
:
;
54: For the “ key
55: For the ” key
Key operation
Print
2334 . ≈
52 ≈
/ / DM :
;
62
≈
Currency
description text
Assigning the drawer number to the drawer for foreign currency
PGM 2
2680
You can assign a number of the drawer which opens when one of the following operations is performed.
• One of [ through ” is pressed without any entry.
• A transaction is completed with a payment entry of foreign currency.
• An X/Z report is issued.
Procedure
2680
.
≈
;
*Drawer no.
*Drawer no.:
0: Inhibit (No drawer opens.)
1: Drawer no. 1
2: Drawer no. 2
Example
Key operation
2680 .
2
Note
Print
≈
;
To perform this programming, an optional drawer must be connected with your register.
A limit amount (HALO) of entry (-, r, p)
PGM 2
2312
Direct
The HALO limit is in effect for the REG-mode operations but can be overridden in the MGR mode. The HALO
limit is represented by two figures as follows:
Procedure
The current
setting is
displayed.
2312
.
*1: Function no.
1: For the - key
2: For the – key
3: For the — key
4: For the ≠ key
≈
*1
Function no.
≈
To keep the current setting
*2
AB
:
;
37: For the r key
38: For the ® key
39: For the p key
40: For the π key
*2: AB is the same as A x 10B.
A: Significant digit (0 through 9)
B: Number of zeros to follow significant digit (0 through 8)
For example, presetting 13 (10.00) here means that amount entries of up to 10.00 are allowed in the REG mode.
When you press 18, however, the upper limit amount is 999999.99.
63
Example
Key operation
Print
2312 . ≈
1 ≈ 13 :
;
HALO limit
+/- sign (%, -)
PGM 2
2311
Direct
Programming of the +/- sign assigns the premium or discount function for each key.
Procedure
The current
setting is
displayed.
2311
.
*1: Function no.
1: For the - key
2: For the – key
3: For the — key
4: For the ≠ key
≈
*1
Function no.
≈
To keep the current setting
*2
ABCDEFG
:
;
5: For the ∞ key
6: For the § key
7: For the ¶ key
8: For the • key
*2:
Item:
A
Selection:
+ (premium) sign
- (discount) sign
+/- sign
Entry:
0
1
0
B to G Always enter 0.
Example
Key operation
Print
2311 . ≈
5 ≈ 0000000 :
6 ≈ 1000000 :
;
“–”: Discount
64
Item % or subtotal % selection (%)
PGM 2
2315
Item %
Select this when a percent calculation is desired for the individual department, PLU and EAN.
Subtotal %
Select this when a percent calculation is desired for subtotals.
Procedure
The current
setting is
displayed.
To keep the current setting
2315
.
≈
*
Function no.
≈
*A
:
;
To repeat
*:
Function no.
5: For the ∞ key
6: For the § key
7: For the ¶ key
8: For the • key
*A:
0: Subtotal %
1: Item %
Example
Key operation
Print
2315 . ≈
5≈1:
6≈0:
;
Item %
Subtotal %
Percent rate limitation (%)
2313
PGM 2
You can program the upper limit of percent rates for percent entries.
(Percent entries that exceed the upper limit may be overridden in the MGR mode.)
Procedure
The current
setting is
displayed.
2313
.
*1: Function no.
5: For the ∞ key
6: For the § key
7: For the ¶ key
8: For the • key
Note
≈
*1
Function no.
≈
To keep the current setting
*2
Rate
:
;
*2: Rate
0.00 – 100.00 (Entering 0.00 inhibits the
open percent rate entry.)
10.00% can be entered as 1 0 or 1
fractional entry.
0 . 0 0.
The . key is needed only for
65
Example
Key operation
Print
2313 . ≈
5 ≈ 15 . 00 :
;
Percentage limit
Item â or subtotal â selection (-)
PGM 2
2316
Item â
Select this when a deduction calculation is desired for the individual department, PLU and EAN.
Subtotal â
Select this when a deduction calculation is desired for subtotals.
Procedure
The current
setting is
displayed.
2316
*:
.
Function no.
1: For the - key
2: For the – key
3: For the — key
4: For the ≠ key
Example
*
Function no.
≈
≈
To keep the current setting
*A
:
;
*A:
0: Subtotal
1: Item â
â
Key operation
Print
2316 . ≈
1≈1:
2≈0:
;
Item
Subtotal
66
8 Programming for the ;, Å, ( through +, and ] through ’ keys
Functional programming
PGM 2
2320
You can set each media for:
Footer printing
This programming decides whether or not your machine should print a message at the foot of a receipt when
a specified media key is used.
Non-add code compulsory
You can enforce the non-add code entry when a media entry is made.
Change enable (over-tender)
Either change enable or disable can be selected for a corresponding media key.
Drawer open
You can program each media key to or not to open the drawer.
Amount tendered compulsory
You may select amount tendered compulsory or optional for the ;, Å and ( through + keys.
You may select amount tendered compulsory or inhibited for the ] through ’ keys.
Procedure
The current
setting is
displayed.
2320
.
≈
*1: Function no.
42: For the ; key
43: For the Å key
44: For the ( key
45: For the ) key
*2 Item:
*1
Function no.
≈
46: For the * key
47: For the + key
48: For the ] key
49: For the } key
To keep the current setting
*2
ABCDEFG
:
;
50: For the ‘ key
51: For the ’ key
Selection:
A
B
Always enter 0.
Footer print
C
Non-add code
D
Change due
E
F
Always enter 0.
Drawer open
G
Amount tendered entry
Entry:
0
Yes
1
No
0
Compulsory
1
Non-compulsory
0
Disable
1
Enable
0
0
No
1
Yes
0
Compulsory
1
Non-compulsory for TL, CA2 or CH1 through CH4 keys
0
Inhibit for the CR1 through CR4 keys
0
67
Example
Key operation
2320 .
50 ≈ 0000001
Print
≈
:
;
A through G
High amount lockout (HALO) for cheque change, cheque cashing,
and cash in drawer PGM 2 2321
You can program the upper limit amounts for cheque change, cheque cashing, and cash in drawer.
Procedure
The current
setting is
displayed.
2321
.
≈
*1
Function no.
*1: Function no.
41: For cheque cashing
66: For cheque change
63: For cash in drawer (Sentinel)
Example
≈
To keep the current setting
*2
Limit
amount
:
;
*2: Limit amount
0 through 999999.99
(Cheque change and cheque cashing)
0 through 9999999.99 (Cash in drawer)
Key operation
Print
2321 . ≈
41 ≈ 9999 :
;
HALO limit
68
High amount lockout (HALO) of entry for media keys
PGM 2
2322
Direct
The HALO limit is in effect for REG-mode operations but can be overridden in the MGR mode. The HALO limit
is represented by two figures as follows:
Procedure
The current
setting is
displayed.
2322
.
*1: Function no.
42: For the ; key
43: For the Å key
44: For the ( key
45: For the ) key
46: For the * key
47: For the + key
*1
Function no.
≈
To keep the current setting
*2
AB
≈
:
;
*2: AB is the same as A x 10B.
A: Significant digit (1 through 9)
B: Number of zeros to follow significant digit
(0 through 8)
48: For the ] key
49: For the } key
50: For the ‘ key
51: For the ’ key
When you press 18, however, the upper limit
amount is 999999.99.
Example
Key operation
Print
2322 . ≈
50 ≈ 15 :
;
HALO limit
9 Programming of function text
Programming
PGM 2
2314
You can program a maximum of 8 characters for each function key and other functions using the table on the
following pages. Select the characters you want to program referring to section “2 How to program alphanumeric
characters” in chapter “PRIOR TO PROGRAMMING.”
Procedure
To program spaces
2314
.
≈
Function no.
(max. 3 digits)
≈
Character keys
(max. 8 digits)
:
;
* Function no.: See “List of function texts” on the following pages.
Example
Key operation
Print
2314 . ≈
48 ≈ VISA :
;
69
List of function texts
Function
no.
Key or function
5
%1
6
%2
7
%3
8
%4
(–)1
(–)2
(–)3
(–)4
%1
%2
%3
%4
9
1
1
2
2
3
3
4
70
Default
setting
4
Function
no.
Key or function
Default
setting
49
Credit 2
CREDIT2
50
Credit 3
CREDIT3
51
Credit 4
CREDIT4
52
Exchange 1
EXCH1
53
Exchange 2
EXCH2
54
Exchange 3
EXCH3
55
Exchange 4
EXCH4
56
Exchange 1 is
EXCH1 IS
Differ
DIFFER
57
Exchange 2 is
EXCH2 IS
10
Taxable 1 subtotal
TAX1 ST
58
Exchange 3 is
EXCH3 IS
11
Taxable 2 subtotal
TAX2 ST
59
EX1 check sale
EX1 CHK
12
Taxable 3 subtotal
TAX3 ST
60
Domestic currency for EX1 check sale DOM.CUR1
13
Taxable 4 subtotal
TAX4 ST
61
EX1 credit sale
14
Taxable 5 subtotal
TAX5 ST
62
Domestic currency for EX1 credit sale DOM. CUR
15
Taxable 6 subtotal
TAX6 ST
63
Cash in drawer
16
VAT/tax 1
VAT 1
64
Cash/cheque is
17
VAT/tax 2
VAT 2
65
Cash/cheque in drawer
CA/CH ID
18
VAT/tax 3
VAT 3
66
Change for cheque
CHK/CG
19
VAT/tax 4
VAT 4
67
Customer
GUEST
20
VAT/tax 5
VAT 5
68
Order total
ORDER TL
21
VAT/tax 6
VAT 6
69
Paid total
PAID TL
22
Net 1
70
Domestic currency 1
DOM.CUR1
23
Net 2
NET1
NET2
71
Domestic currency 2
DOM.CUR2
24
Coupon-like PLU
CP PLU
72
Domestic currency 3
DOM.CUR3
25
Refund
REFUND
73
Domestic currency 4
DOM.CUR4
26
Void
74
Cheque in drawer
CH ID
27
Void mode total
75
Commission sale 1
COM.SAL1
28
MGR void
MGR
76
Commission sale 2
COM.SAL2
29
Subtotal void
SBTL
77
Commission sale 3
COM.SAL3
30
Hash void
HASH
78
Commission sale 4
COM.SAL4
31
Hash refund
HASH RF
79
Commission sale 5
COM.SAL5
32
VAT shift
VAT SFT
80
Commission sale 6
COM.SAL6
33
VAT/tax delete
TAX DELE
81
Commission sale 7
COM.SAL7
35
No sale
NO SALE
82
Commission sale 8
COM.SAL8
36
Guest check counter
G.C. CNT
83
Commission sale 9
COM.SAL9
37
RA
RA
84
Non commission sale
NON.COM
38
RA2
RA2
85
(+) Dept total
39
PO
PO
86
(-) Dept total
40
PO2
PO2
87
Hash (+) total
41
Cheque cashing
CA/CHK
88
Hash (-) total
MODE
EX1 CR.
CID
CA/CH IS
DEPT TL
DEPT (-)
HASH TL
HASH (-)
42
Cash
Bottle return (+) total
Cash 2
CASH
CASH2
89
43
90
Bottle return (-) total
44
Cheque 1
CHECK
91
Net 1 (Taxable 1 - VAT/tax 1) NET 1
45
Cheque 2
CHECK2
92
Net 2 (Taxable 2 - VAT/tax 2) NET 2
46
Cheque 3
CHECK3
93
Net 3 (Taxable 3 - VAT/tax 3) NET 3
47
Cheque 4
CHECK4
94
Net 4 (Taxable 4 - VAT/tax 4) NET 4
48
Credit 1
CREDIT1
95
Net 5 (Taxable 5 - VAT/tax 5) NET 5
BTTL TL
BTTL (-)
Function
no.
Default
setting
Key or function
Function
no.
Key or function
Default
setting
96
Net 6 (Taxable 6 - VAT/tax 6) NET 6
122
Commission amount 1
COM.AMT1
97
Subtotal
SUBTOTAL
123
Commission amount 2
COM.AMT2
98
Merchandise subtotal
MDSE ST
124
Commission amount 3
COM.AMT3
99
Difference subtotal
DIFF ST
125
Commission amount 4
COM.AMT4
126
Commission amount 5
COM.AMT5
100
Total
TOTAL
101
Change
CHANGE
127
Commission amount 6
COM.AMT6
102
Sales q'ty
ITEMS
128
Commission amount 7
COM.AMT7
103
Link PLU and EAN link subtotal ITEM ST
129
Commission amount 8
COM.AMT8
104
Copy receipt title
COPY
130
Commission amount 9
COM.AMT9
105
Guest check copy title
G.C COPY
131
Commission amount total
COM.TTL
106
Average
AVE.
132
Department report title
DEPT
133
Group report title
GROUP
134
PLU report title
PLU
135
Transaction report title
TRANS.
136
Total in drawer report title
TL-ID
137
Clerk report title
CLERK
138
Cashier report title
CASHIER
139
Hourly report title
HOURLY
140
Daily net report title
DAILY
141
PLU zero sales report title
ZERO SAL
142
PLU price category report title CATEGORY
107
Group 1 for departments
108
Group 2 for departments
109
Group 3 for departments
110
Group 4 for departments
111
Group 5 for departments
112
Group 6 for departments
113
Group 7 for departments
114
Group 8 for departments
115
Group 9 for departments
116
CCD
GROUP01
GROUP02
GROUP03
GROUP04
GROUP05
GROUP06
GROUP07
GROUP08
GROUP09
CCD
117
CCD differ
CCD DIF.
143
Commission sales report title SALES
118
CCD differ total
DIF. TL
144
EAN report title
EAN
119
Order total-Paid total
O-P
145
EAN price change
PR.CHNG
120
Total tax
TTL TAX
146
Non accessed EAN report title DELETE
121
Net without tax
NET
10 Cashier and clerk programming
Cashier code
PGM 1
PGM 2
1500
You can assign a cashier code to each cashier. (If the cashier’s file is upgraded, a maximum of 99 cashiers can
be programmed. Consult your dealer.)
Procedure
To keep the current setting
1500
.
≈
Cashier no.
(1 to 99)
≈
*Cashier code
(0 - 99)
:
;
The current setting is displayed.
* Programming cashier code “0” inhibits entries of the cashier code.
71
Example
Key operation
Print
1500 . ≈
1 ≈ 11 :
4 ≈ 14 :
Cashier no.
Cashier code
;
Cashier name
PGM 1
PGM 2
1514
You can program a maximum of 8 characters (cashier name) for each cashier. Select the characters you want to
program referring to section “2 How to program alphanumeric characters” in chapter “PRIOR TO
PROGRAMMING.”
Procedure
To program spaces
*
1514
.
≈
Cashier code
(1 - 99)
Character keys
(max. 8 digits)
≈
:
;
*: A cashier code you have programmed for the cashier by job code 1500
Example
Key operation
Print
1514 . ≈
11 ≈ MAYER :
;
Functional programming for cashiers
PGM 2
2510
Procedure
To keep the current setting
*
2510
.
≈
Cashier code
(1 - 99)
≈
**A B C D E
:
The current setting is displayed.
*: A cashier code you have programmed for the cashier by job code 1500
**
Item:
A
Guest check copy
B
VAT shift
C and D Always enter 0.
E
Drawer
72
Selection:
Disable
Enable
Yes
No
Set the drawer no. 1 or 2
Use no drawer
Entry:
1
0
1
0
0
1 or 2
0
;
Example
Key operation
Print
2510 . ≈
11 ≈ 00001 :
;
E(Drawer no.)
A through D
Clerk code
PGM 1
1400
PGM 2
You can assign a clerk code to each of 99 clerks. The standard machine has no clerk function. If you need this
function, consult your dealer.
Procedure
To keep the current setting
1400
.
≈
Clerk no.
(1 to 99)
≈
*Clerk code
(0 - 99)
;
:
The current setting is displayed.
*: Programming clerk code “0” inhibits entries of the clerk code.
Example
Key operation
Print
1400 . ≈
1 ≈ 11 :
4 ≈ 14 :
Clerk no.
Clerk code
;
Clerk name
PGM 1
PGM 2
1414
You can program a maximum of 8 characters (clerk name) for each clerk. Select the characters you want to
program referring to section “2 How to program alphanumeric characters” in chapter “PRIOR TO
PROGRAMMING.”
Procedure
To program spaces
*: A code you have programmed for* the clerk by the job code 1400.
1414
.
≈
Clerk code
(1 - 99)
≈
Character keys
(max. 8 digits)
:
;
*: A clerk code you have programmed for the clerk by the job code 1400
Example
Key operation
Print
1414 . ≈
11 ≈ NILS :
;
73
11 Programming various functions
Programming for optional feature selection
PGM 2
2616
OP X/Z mode availability
When a cashier needs to take the cashier/clerk X or Z report, he or she will use the OP X/Z mode. This
programming determines whether he or she will be allowed to use this mode.
Note
You can take cashier/clerk X and Z reports in the X1/Z1 mode regardless of the above
programming.
Paid out in the REG-mode
Refund key in the REG-mode
Direct void in the REG-mode
Indirect void in the REG-mode
Subtotal void in the REG-mode
First item direct void
Printing of the number of purchased items
Journal print form
You may choose either of the following forms.
• Detailed journal print that shows the details of all entries - the same information as printed on the receipt.
• Summary journal print that shows information about all entries other than normal department entries
(entries into “+” departments and their associated “+” PLUs).
Zero skip for various reports
VAT/tax amount, taxable amount and net amount printing on the receipt/journal
VAT shift type
VAT shift by cashier: VAT shift is performed by the operation of a cashier who has been assigned to do the
VAT shift operation (Refer to job# 2510).
VAT shift by shift key: VAT shift is performed by pressing the VAT shift key.
No sale in REG-mode
Finalization when the subtotal amount is zero in the REG mode
Exchange 1 calculation method (for EURO settings)
When you do not introduce EURO, keep the default setting (multiplication).
When you introduce EURO, this setting is automatically set by the operation of job #800 in the X2/Z2 mode.
The calculation method is as follows:
In case that “Division” is selected for the period 1,
Domestic currency amount (national currency amount) Exchange 1 rate (EURO conversion rate) =
Exchange 1 amount (EURO amount)
In case that “Multiplication” is selected for the period 2,
Domestic currency amount (EURO amount) Exchange 1 rate (EURO conversion rate) = Exchange 1
amount (national currency amount)
Printing of the exchange 1 total amount and change amount on the receipt/journal
Total and change amounts in exchange 1 currency are printed respectively below each of the total and
exchange amounts in domestic currency.
When you introduce EURO, this setting is automatically set by the operation of job #800 in the X2/Z2 mode
as follows:
On the period 1, EURO amount converted from national currency is printed below the national currency, and
on the the period 2, national currency converted from EURO amount is printed.
Cash/credit operation for exchange 1
You can set whether you receive foreign currency (exchange 1) amount by cheque or credit or not.
Footer graphic logo printing
Credit counting when received-on-account/paid out finalized with the credit key
74
Separator line in the report
Link PLU printing on the receipt
EAN learning function
Price change for EAN entry in REG mode
Treatment of EAN 8 code (200XXXXC/D)
Treatment of EAN 13 code (2XXXXXXXXXXXC/D)
Price entry after ISBN or ISSN
Entry of EAN with add-on code when the EAN ADD-ON file is full
Procedure
To keep the current setting
2616
.
≈
**
P
≈
*ABCDEFGH
;
:
(1 to 14)
The current setting is displayed.
**P: 1
*
Item:
A
OP X/Z mode
B
Paid-out in REG-mode
C
D
Always enter 0.
Refund key entry in the REG-mode
E
Direct void in the REG-mode
F
Indirect void in the REG-mode
G
Subtotal void in the REG-mode
H
Always enter 0.
Selection:
Enable
Disable
Enable
Disable
Enable
Disable
Enable
Disable
Enable
Disable
Enable
Disable
Entry:
0
1
0
1
0
0
1
0
1
0
1
0
1
0
**P: 2
*
Item:
A
The first item direct void
B and C Always enter 0.
D
Printing of the number of purchased items
Selection:
Enable
Disable
No
Yes
E
F
Always enter 0.
Journal print form
G and H Always enter 0.
Detailed
Limited
Entry:
0
1
0
0
1
0
0
1
0
75
**P: 3
*
Item:
A
Zero skip in EAN report
B
Zero skip in clerk report
C
Zero skip in cashier report
D
Zero skip in transaction report
E
Zero skip in department report
F
Zero skip in PLU report
G
Zero skip in hourly report
H
Zero skip in daily net report
Selection:
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Entry:
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
**P: 4
*
Item:
A and B Always enter 0.
C
VAT/tax amount printing on the
receipt/journal
D
Taxable amount printing on the
receipt/journal
E
Net amount printing on the receipt/journal
F to H
Selection:
Yes
No
Yes
No
Yes
No
Always enter 0.
Entry:
0
0
1
0
1
0
1
0
**P: 5
*
Item:
A to C
D
Always enter 0.
VAT shift type
Selection:
E to H
Always enter 0.
By cashier
By shift key
Entry:
0
0
1
0
**P: 6 (ABCDEFGH: Always enter 0.)
**P: 7
*
Item:
A and B Always enter 0.
C
No sale in REG-mode
D
E to H
Finalization in the REG-mode
when the subtotal amount is zero
Always enter 0.
**P: 8 (ABCDEFGH: Always enter 0.)
76
Selection:
Enable
Disable
Enable
Disable
Entry:
0
0
1
0
1
0
**P: 9
*
Item:
A
B
Always enter 0.
Exchange 1 calculation method
C
Cheque/credit operation for exchange 1
D
Printing exchange 1 total amount and change
amount on receipt and journal
Always enter 0.
Footer graphic logo printing
E to G
H
Note
Selection:
Multiplication
Division
No
Yes
No
Yes
Yes
No
Entry:
0
0
1
0
1
0
1
0
1
0
The items B and D are automatically set by the operation of job #800 in the X2/Z2 mode.
**P: 10
*
Item:
A and B Always enter 0.
C
Learning function for EAN entry
D to H
Selection:
Yes
No
Always enter 0.
Entry:
0
0
1
0
**P: 11 (ABCDEFGH: Always enter 0.)
**P: 12
*
Item:
A to G
H
Selection:
Always enter 0.
Price change for EAN entry in REG mode
Enable
Disable
Entry:
0
0
1
**P: 13
*
Item:
A
B
C
Credit counting when received-on-account/paid
out is finalized with the credit key
Separator line in the report
Way to print the information for the link PLU/EAN
link on the receipt
D and E Always enter 0.
F
Treating the EAN8 code
(200XXXXC/D) as PLU type (XXXX:PLU code)
G
Treatment of the EAN13 code
(2XXXXXXXXXXXC/D)
H
Price entry after ISBN or ISSN
Selection:
Yes
No
Separator line
1 line space
Leading link PLU/EAN with
total amount
Detailed information
No
Yes
Dept. code
PLU code
Inhibited
Compulsory
Entry:
1
0
1
0
1
0
0
1
0
1
0
1
0
77
**P: 14
*
Item:
A
B
C to H
Selection:
Always enter 0.
Entry of EAN with add-on code when EAN
ADD-ON file is full
Always enter 0.
Example
Entry:
0
0
1
0
Continued
Inhibited
Key operation
Print
2616 . ≈
3 ≈ 00000010 :
P: 1 through 14
;
A through H
Programming feed line after printing of a difference subtotal
Procedure
When A and B are zeroes
2615
.
≈
* AB
;
* A: Always enter 0.
B: Feed lines after printing of difference subtotal (0 through 9)
Example
Key operation
2615 . ≈
01 ;
78
Print
PGM 2
2615
Programming alarm length of time with drawer opening
PGM 2
2617
If the drawer still remains open when a specified length of time has elapsed, your machine gives the alarm.
Procedure
To disable the alarm function
2617
.
≈
Time
1 to 255 seconds
;
Example
Key operation
Print
2617 . ≈
30 ;
Note
Your machine starts to monitor how long the drawer is kept open the moment the drawer is opened
at the end of a transaction in the REG/VOID mode. It stops the time monitoring when a valid key
(except the q key) is pressed for the next transaction. It restarts the time monitoring after that
transaction is ended. You can stop the buzzer alarm by closing the drawer. No key entries can be
made while the buzzer is sounding.
79
Programming of logo messages
2614
PGM 2
Your register can print programmed messages for customers on every receipt. On the standard model, only
graphic logo is printed on the receipt. (If you want a graphic logo customerized for your store, please consult
your dealer.)
If you want to print logo message, please consult your dealer. You have five options described below.
Select the characters you want to program, referring to section “2 How to program alphanumeric characters” in
chapter “PRIOR TO PROGRAMMING.”
Procedure
To program spaces
2614
.
≈
*Line number
(1 to 6)
≈
Character keys
(max. 24 digits)
:
;
* “Header 3-line message” type: 1 to 3
“Footer 3-line message” type : 4 to 6
“Header 6-line message” type: 1 to 6
“Header 3-line and footer 3-line message” type: 1 to 6 (1 to 3 as header, 4 to 6 as footer)
Text 1st line
Graphic logo
Text 2nd line
Graphic logo
Graphic logo
Text 3rd line
Default setting
Example
Text 1st line
Text 2nd line
Text 2nd line
Text 3rd line
Text 3rd line
Text 1st line
Text 4th line
Text 2nd line
Text 5th line
Text 3rd line
Text 6th line
Header 3-line message
Text 4th line
Text 4th line
Text 5th line
Text 5th line
Text 6th line
Text 6th line
Footer 3-line
message
Header 6-line
message
Header 3-line
message and
footer 3-line
messages
To program the following logo messages by using 3 lines:
=== YOUR ===
== STORE ==
MESSAGE
Key operation
2614 .
1≈/
80
Text 1st line
≈
/ / é=é=é=/
Y
Î ÎOÎUÎR
/é=é=é=:
2≈///é=é=/
ÎSÎTÎOÎRÎE
/é=é=:
3≈////
ÎMÎEÎSÎSÎAÎGÎE
:
;
(/:Space key)
Print
Selection of X1/Z1 and X2/Z2 reports
to be printed in the stacked report sequence
2620
PGM 2
Your register is equipped with the stacked report printing function that enables multiple X/Z reports to be printed
in sequence with only a single request, up to maximum of 15 reports*. This function continuously prints a
maximum of 15 kinds of reports with a single operation.
Procedure
≈
.
2620
To cancel the stacked report sequence
For full reporting (non-range report)
*1
Job no.
*2
Start range
parameter
≈
*2
End range
parameter
≈
:
;
For individual reporting
To repeat*
*: Maximum 70 steps are programmable. “1 step” means the memory size used for one no-range type job no.
The range type job no. needs “8 steps”.
Job code numbers to be used are as follows.
*1
Job no.
Report
*2
Available mode
00
General report
07
EAN zero sales report
09
Full EAN report
10
Full department report
X1/X2 mode only
13
Full department group report
X1/X2 mode only
20
PLU report
27
PLU zero sales report
29
PLU price category report
X1/X2 mode only
30
Transaction report
X1/X2 mode only
31
Total in drawer report
X1/X2 mode only
32
Commission sales report
40
Full clerk report
50
Full cashier report
60
Hourly sales information
Range parameter
X1/X2 mode only
*3 Start PLU code/end PLU code (1 through 999999)
X1/X2 mode only
Range report is available
*3 Start price amount/end price amount
*3 Start time/end time (0 through 2330)
only in the X1 mode.
70
Daily net report
X1/X2 mode only
*3: Both range setting and full setting are allowed.
Note
When Z of stacked report is initiated, X only reports will be skipped.
Example
Key operation
Print
2620 . ≈
10 :
13 :
;
81
Setting the time range for hourly reports
PGM 2
2619
You can set the time range for an hourly report.
Procedure
When A through C are all zeros
2619
.
≈
*
;
ABC
*A: Time range
To set the time range to 30 minutes (in the 24-hour system), enter 0.
To set the time range to 60 minutes (in the 24-hour system), enter 1.
BC: Starting time (hour = 00 to 23)
Example
Key operation
Print
2619 . ≈
107 ;
Note
To perform this setting, an hourly Z report (# 160) must be done.
RS-232C channel assignment
2690
PGM 2
Your machine is equipped with two RS-232C interfaces. If you use the on-line communication function and/or
the barcode reader, the channel number of each RS-232C interface must be programmed by using the following
procedure.
To realize the on-line communication and/or to use the barcode reader, consult your dealer.
Procedure
When A through D are all zeroes
2690
.
≈
*P
≈
**ABCD
:
;
1 to 3
*P: 1
**
Item:
A
B to D
Channel no. for the ON-LINE
communication
Selection:
Not connected
Standard port 2
Standard port 1
Entry:
0
1
8
0
Selection:
Not connected
Standard port 2
Standard port 1
Entry:
0
1
8
0
Always enter 0.
*P: 2
**
Item:
A
Channel no. for the barcode reader
B to D
Always enter 0.
*P: 3 (ABCD: Not used. Always enter 0.)
Note
82
Never enter any number other than 0, 1 and 8.
Example
Key operation
Print
2690 . ≈
1≈:
P
A through D
;
Barcode reader programming
PGM 2
2691
Procedure
To program zeros
2691
*
.
≈
Item:
A
Data bit
B
Parity bit
C
Stop bit
D
Transmission speed
Example
;
* ABCD
Selection:
7 bits
8 bits
Non parity
Odd parity
Even parity
1 bit
2 bits
19200 bps
9600 bps
4800 bps
Key operation
Entry:
1
0
2
1
0
1
0
2
1
0
Print
2691 . ≈
1110 ;
ABCD
83
Secret codes to control access to PGM1 mode, X1/Z1 mode and X2/Z2
2631
2632
mode PGM 2 2630
You must enter a secret code according to the following procedure before performing any PGM1-mode, X1/Z1mode or X2/Z2-mode operation when a secret code has been set for that specific mode operation.
Operating
Procedure
;
;
Secret code
Max. 4 digits
Note
Once a secret code is entered, it does not need to be entered again unless the mode switch setting
is changed and any operation is performed.
Programming
Procedure
*
2630
2631
2632
No code (zero)
.
≈
Secret code
;
Max. 4 digits
* 2630 for the PGM1 mode
2631 for the X1/Z1 mode
2632 for the X2/Z2 mode
Example
Key operation
2631 . ≈
1234 ;
84
Print
Functional programming for the printer
PGM 2
2990
You can program functions for the printer.
When A through D are all zeroes
Procedure
2990
*
.
Item:
A
B
C and D
Example
≈
;
*ABCD
Selection:
Always enter 1.
Always enter 0.
Printing density
80% for standard=00
90% for standard=50
100% for standard=99
Key operation
2990 .
1050
Entry:
1
0
00-99
Print
≈
;
Printing density
85
Setting the AUTO key — Automatic sequencing key —
X2/Z2
2900
If you program frequently performed transactions or report sequences for the AUTO keys, you can call those
transactions and/or reports simply by pressing the corresponding AUTO keys in key operations. This
programming can be done when your machine is in the X2/Z2 mode.
Procedure
Delete
≈
£
¡
™
Transaction
1
max. 25 times
1
¢
¢
;
10
10
Example
£
¡
™
.....
.
.....
2900
Programming for ~ key and ¡ key as follows:
~; entering a PLU 2 item (programmed unit price: 1.50) and a dept. 6 item (unit price: 1.00)
¡; selling a dept. 7 item (programmed unit price: 5.00) for cash
Key operation
Print
2900 . ≈
£
1
AUTO1
setting
2 ß 100 6
£
¡
7;
¡
;
1
AUTO2
setting
Note
86
When the AUTO key has been programmed to execute a report job function etc., the mode switch
must be in the appropriate position (X1/Z1 or X2/Z2).
12 Reading stored programs
Your machine allows you to read every program stored in the PGM1 and PGM2 modes.
Program details and procedures for their reading
Program for:
Mode
switch
position
Job
code no.
≈
1100
1
Departments
PGM2 or
PGM1
For reading all codes
For individual reading
1100
Start
dept. code
1200
2
PLUs/
subdepartments
PGM2 or
PGM1
Key nos. for
departments and
PLUs
PGM2
2119
Link PLUs
PGM2
End
PLU code
≈
≈
2119
;
;
;
Start
PLU code
≈
End
PLU code
2220
;
1000
5
EANs
PGM1 or
PGM2
≈
1000
1200, 1210,
1211, 2210,
2211, 2214,
2215, 2230,
2231, 2232,
2235
2119, 2219
For reading all codes
For individual reading
2220
1110, 2110,
2111, 2112,
2114, 2115,
2116
≈
2220
4
End
dept. code
≈
≈
For reading all codes
For individual reading
1200
Start
PLU code
3
Related PGM1/
PGM2 job
code nos.
Procedure
For reading all codes
For the last EAN picking list
≈
Scan EAN code
Ä
;
1000, 1010
1011, 2010
2011, 2014
2015
≈
EAN code
To pick up EAN codes
6
EANs function
PGM2
2025
2025
≈
;
2025, 2029,
2035
7
EAN link
PGM2
2030
2030
≈
;
2030
8
Cashiers
PGM2 or
PGM1
1500
1500
≈
;
1500, 1514,
2510
9
Clerks
PGM2 or
PGM1
1400
1400
≈
;
1400, 1414
10
11
Function preset 1
Function preset 2
PGM2 or
PGM1
PGM2
1300
2600
1300
2600
≈
≈
;
1310, 2311,
2312, 2313,
2314, 2315,
2316, 2320,
2321, 2322,
2330, 2334
;
2614, 2615,
2616, 2617,
2619, 2620,
2630, 2631,
2632, 2680,
2690, 2691
87
Program for:
Mode
switch
position
Job
code no.
Related PGM1/
PGM2 job
code nos.
Procedure
12
Tax rates
PGM2
2700
2700
≈
;
2711
13
Auto keys
PGM2
2900
2900
≈
;
2900
14
Thermal printing
PGM2
2990
2990
≈
;
2990
Sample printouts
1 Reading of programmed items for departments
(Reading in the PGM1 and PGM2 modes)
Job code no.
Range
Dept. code
Item label
2 Reading of programmed items for
PLUs/subdepartments
(Reading in the PGM1 and PGM2 modes)
Mode switch
position*
Mode switch
position*
Range
PLU code
Tax status
Unit price
Group no.
Tax status
Item label
HALO limit.
Commission group
Function
programming
0 0 0 0 0 0 1
Unit price
Associated
dept. code
Base q'ty
0 0 3
Mode
parameter
Commission
group
Type of unit
price entry
Type
(SIF/SICS/Normal)
Minus department
Link PLU
* When you take this report in the PGM1 mode, the PGM2
indication is replaced by a “PGM1”.
88
3 Reading of programmed key nos. for
departments and PLUs
(Reading in the PGM2 mode)
Key no.
Dept. code
4 Reading of programmed items for link PLUs
(Reading in the PGM2 mode)
Range
Linked
PLU code
Leading
PLU code
5 Reading of programmed items for EANs (1)
(Reading in the PGM1 and PGM2 modes)
Mode switch position*
PLU code
Type L: Linked with PLUs
(space): Normal
EAN code
Unit price
Commission group
Delete method
Item label
Base q’ty
Tax status
Associated dept. code
* When you take this report in the PGM1 mode, the PGM2
indication is replaced by a “PGM1”.
Note
The EAN codes are printed out in the sequence
shown below.
EAN-13
EAN-8
UPC-A
UPC-E
89
6 Reading of programmed items for EANs (2)
(Reading in the PGM2 mode)
8 Reading of programmed items for cashiers
(Reading in the PGM1 and PGM2 modes)
Mode switch
position*
Cashier no.
Non-PLU format
setting
Cashier name
Cashier code
Guest check copy
yes/no
Drawer no.
VAT shift yes/no
Delete period
Press code
function
* When you take this report in the PGM1 mode, the PGM2
indication is replaced by a “PGM1”.
7 Reading of programmed items for EAN link
(Reading in the PGM2 mode)
9 Reading of programmed items for clerks
(Reading in the PGM1 and PGM2 mode)
Mode switch
position*
EAN code
Clerk no.
Linked PLU
codes
Clerk code
Clerk name
* When you take this report in the PGM1 mode, the PGM2
indication is replaced by a “PGM1”.
90
10 Reading of programmed items for functions - 1
(Reading in the PGM1 and PGM2 modes)
Mode switch
position*
To be continued on the next page
* When you take this report in the PGM1 mode,
the PGM2 indication is replaced by a “PGM1”.
To be continued on the next page
91
11 Reading of programmed items for functions - 2
(Reading in the PGM2 mode)
Logo message
Line feed for differ ST
Optional feature selection
Drawer open alarm time
Hourly report format/start
hour
Stacked report
Secret code
Drawer no. for the drawer
for foreign currency
RS-232C channel data
Barcode reader
programming
92
12 Reading of programmed tax rates
(Reading in the PGM2 mode)
14 Reading of programmed items for the thermal
printer (Reading in the PGM2 mode)
Printing density
Tax rate
Lowest taxable
amount
Entered Value
Printing density
example
13 Reading of programmed items for auto keys
(Reading in the PGM2 mode)
93
13 Training mode
The training mode is used when the operator or the manager practices register operations.
When a cashier set in training is selected, the machine automatically enters the training mode. When a cashier
not set in training is selected, the machine automatically enters the ordinary REG mode. (For programming,
consult your dealer.)
The training operations is valid only in REG, MGR and VOID mode.
The corresponding cashier memory is updated in the training mode. Other memories are not updated.
Key operation
Print
1000 5
3≈
3
;
94
READING (X) AND RESETTING (Z)
OF SALES TOTALS
• Use the reading function (X) when you need to take a reading of sales information entered since the last
resetting. You can take this reading any number of times. It does not affect the register’s memory.
• Use the resetting function (Z) when you need to clear the register’s memory. Resetting prints all sales
information and clears the entire memory except for the GT1 through GT3 and training GT, reset count, and
consecutive number.
Summary of reading (X) and resetting (Z) reports and the key operations
1 to obtain the reports
X1 and Z1 reports: Daily sales reports
X2 and Z2 reports: Periodic (monthly) consolidation reports
Item
Flash report:
(Only display)
To clear the display,
key
press the
or turn the mode
switch to another
position.
c
Full reading and
resetting
Mode switch
position
X1/Z1
X2/Z2
Job
code
Key operation
1 to ÿ ) : Department total amount
Dept. code
à
≈ key: Amount of cash in drawer
: key: Sales total
Dept. key (
X1
—
—
X1, Z1
X1, Z1
100
X1, Z1
Individual clerk
reading and
resetting
X2, Z2
200
X1, Z1
141
X2, Z2
241
Reading
100
200
.
≈
;
≈
;
≈
;
≈
;
≈
;
≈
;
≈
;
Resetting
Reading
141
241
.
Resetting
Reading
<OP X/Z> X, Z
41
41
.
Resetting
X1, Z1
Individual cashier
reading and
resetting
X1, Z1
X2, Z2
Reading
151
251
151
251
.
Resetting
Reading
<OP X/Z> X, Z
51
51
.
Resetting
Full clerk
reading and
resetting
X1, Z1
Full cashier reading
and resetting
X1, Z1
Full department
reading
X1
Individual group
reading
X1
Full group reading
X1
X1, Z1
140
X2, Z2
240
X1, Z1
150
X2, Z2
250
X1
X2
X1
X2
X1
X2
110
210
112
212
113
213
Reading
140
240
.
Resetting
Reading
150
250
110
210
112
212
113
213
.
Resetting
≈
≈
≈
;
Group no.
;
;
95
Item
Mode switch
position
X1/Z1
X2/Z2
Job
code
Key operation
Reading
Reading and
resetting of sales
information for a
range of PLUs/
subdepartments
X1, Z1
X1, Z1
120
120
220
.
≈
Resetting
All PLUs
X2, Z2
220
≈
Start PLU code
Reading of sales
information of PLUs/
subdepartments
associated with an
individual department
Reading of sales
information on
PLUs/
subdepartments
whose sales
amounts are zeros
Reading of PLU/
subdepartments
whose sales
amounts are zeros
(by associated
department)
Reading of sales
information
for the price amount
range of PLUs/sub
department
X1
X1
X1
X1
X1
121
X2
221
X1
127
X2
227
X1
127
X2
227
X1
129
121
221
≈
Dept. code
127
227
≈
;
127
227
≈
Dept. code
129
229
≈
End
PLU code
;
;
;
All prices
X2
229
Start price
amount
≈
End price
amount
;
Reading
X1, Z1
X1, Z1
109
109
209
.
For full reading and resetting
Resetting
Reading and
resetting of sales
information for
EANs
For the last EAN picking list
≈
X2, Z2
Scan EAN code
209
EAN code
≈
Ä
≈
To pick up EAN codes
Reading and
resetting of sales
information for
EANs associated
with an individual
department
Reading of EANs
whose sales
amounts are zeros
X1, Z1
X1, Z1
101
201
X1
X2, Z2
201
X1
107
207
.
≈
Resetting
107
207
X2
96
Reading
101
≈
;
Dept. code
;
;
Mode switch
position
X1/Z1
X2/Z2
Item
Reading of EANs
whose sales
amounts are zeros
(by associated
department)
Commission sales
report
Transaction reading
Total in drawer
X1
X1
X1
X1
X1
Job
code
107
X2
207
X1
X2
X1
X2
X1
X2
132
232
130
230
131
231
107
207
≈
132
232
≈
≈
≈
130
230
131
231
Reading: 160
(For individual
time range)
X1
Reading and
resetting of hourly
sales information
Key operation
;
Dept. code
;
;
;
≈
Start*
time
≈
;
End*
time
160
* Enter the time in the 24-hour system.
Reading
and
Resetting: 160
X1, Z1
Reading
.
;
≈
Resetting
Reading and
resetting of a
stacked report
X1, Z1
Reading
190
X2, Z2
290
X2, Z2
270
190
290
.
≈
;
≈
;
Resetting
When Z of stacked report
is initiated, X only reports
will be skipped.
Reading
Reading and
resetting of the
daily net totals
Note
X1, Z1
270
.
Resetting
Individual and full clerk reading and resetting are available only in the cashier and clerk system. In
the factory setting, the register provides the “cashier only” system. So, if you want to change the
system, consult your dealer.
Non-accessed EAN deleting
Mode switch
position
X1/Z1
X2/Z2
Item
Reading of
non-accessed
EANs
X1
Job
code
105
Key operation
105
≈
;
For full deleting
For the last EAN picking list
Deleting of
non-accessed
EANs
Z1
105
105
. ≈
Scan EAN code
EAN code
≈
;
Ä
≈
To pick up EAN codes
Note
When you execute the job #105 in Z1 mode, not only the sales data, but also the EAN code(s) (the
related data files) themselves will be deleted.
97
2 Daily sales totals
Full reading and resetting of sales totals
You can take X and Z reports in the X1/Z1 mode. The use of the decimal key (.) determines when the report
will actually reset the sales totals.
• Sample X report
• Sample Z report
Report no.
Read symbol
Reset symbol
Reset counter
Net grand total
(GT2 - GT3)
Grand total of
plus registration
Dept. code
Sales q'ty
Sales amount
Grand total of
minus registration
Ratio of dept.1
sales amount to “+”
dept. total
Grand total of training
mode registration
The subsequent printout occurs in the
same format as in the X report.
Group1 sales q'ty
Group1 sales amount
Ratio of dept. group1
sales amount to “+”
department
“+” dept. counter
and total
To be continued on the next page
Note
98
Not all reports provide the resetting capability. Please refer to the chart on pages 95 through 97.
“-” dept. counter and total
“+” hash dept. counter and total
“-” hash dept. counter and total
“+” bottle return dept. counter and total
“-” bottle return dept. counter and total
Subtotal
3 counter and total
Subtotal percent 1 counter and total
Net sales total
Taxable 1 total
VAT 1 total
Tax total
Net total without tax
VAT shift total
Tax delete total
Item
1 counter and total
To be continued on the next page
99
Item percent 3 counter and total
Refund counter and total
REG-mode void counter and total
Void-mode transaction counter and total
Manager item void counter and total
Subtotal void counter and total
Hash dept. void counter and total
Hash refund counter and total
No-sale (exchange) counter
Gest check copy counter
Customer counter
Order total
Paid total
Paid total average per costomer
Received on account counter and total
Paid out counter and total
Cheque cashing counter and total
Cash counter and total
Cheque 1 sales counter and total
Credit 1 sale and tendering counter and total
To be continued on the next page
100
Exchange 1 counter and total
Exchange 1 cheque 1-4 counter and total
Exchange 1 cheque 1-4 total in domestic currency
Exchange 1 credit 1-4 counter and total
Exchange 1 credit 1-4 total in domestic currency
Cash in drawer
Cheque in drawer
Cash + cheque in drawer
Change total for cheque tendering
101
Cashier reading and resetting
Using this function, you can take X and Z reports for individual cashiers or all cashiers.
Individual cashier reading and resetting
The OP X/Z-mode reading and resetting is allowed only when your machine has been programmed
Note
for “OP X/Z mode available” in the PGM2 mode.
• Sample X report
• Sample Z report
Cashier no./cashier code
Cashier name
Order total
Paid total
Average
The subsequent printout occurs in the
same format as in the sample X report.
* When you take these reports in the OP X/Z mode, the X report shows an
“OP X” and the Z report shows an “OP Z”.
102
Full cashier reading and resetting
The subsequent printout occurs in the same format as in the
sample reports of individual cashier reading and resetting,
and sales data for cashiers print in this sequence.
103
Clerk reading and resetting
Using this function, you can take X and Z reports for individual clerks or all clerks.
Individual clerk reading and resetting
The OP X/Z-mode reading and resetting is allowed only when your machine has been programmed
Note
for “OP X/Z mode available” in the PGM2 mode.
• Sample X report
• Sample Z report
Clerk no./clerk code
Clerk name
Order total (Net sales total)
Commission sales
1 total amount
The subsequent printout occurs in the
same format as in the sample X report.
Non-commission
sales amount
Full clerk reading and resetting
The subsequent printout occurs in the same format as
in the reports of individual clerk reading and resetting,
and sales data for clerks print in this sequence.
* When you take these reports in the OP X/Z mode, the X report shows an “OP X” and the Z report shows an
“OP Z”.
104
Reading and resetting of hourly sales information
You can take X and Z reports for sales totals and transaction (customer) counters for 48 half hours, or 24 hours.
If both quantity and amount are zero, their print is skipped.
• Sample X report
• Sample Z report
Customer counter
Sales total
Average sales
amount per customer
(sales total ÷
customer counter)
The subsequent printout occurs in the
same format as in the sample X report.
105
Full department reading
Sales q'ty and total
Ratio of dept. 1 sales
amount to “+”
dept. total
106
Individual group reading
Full group reading
Group 1 sales q'ty and
total
Group 1 sales q'ty and
total
107
Reading and resetting of sales information for a range of
PLUs/subdepartments
This function provides you with X and Z reports for sales information of a certain range of PLUs/subdepartments.
You must enter the start and end PLU/subdepartment code of the range. Of course, the range may represent all
of the PLUs/subdepartments in your register.
• Sample X report
• Sample Z report
Range
PLU code
Item label
Sales q'ty and total
The subsequent printout occurs in the same
format as in the sample X report.
Range sum
108
Reading of sales information on
PLUs/subdepartments associated
with an individual department
Reading of PLUs/subdepartments
whose sales amounts are zeros
(by associated department)
Associated dept.code
PLU code
Sales q'ty and total
Associated
dept. code
Reading of sales information for
the price amount range of
PLUs/subdepartments
Reading of PLUs/subdepartments
whose sales amounts are zeros
Price amount
range
Sales q'ty
and total
PLU code
Item label
109
Reading and resetting of sales information for EANs
• Sample X report
EAN code
Sales q'ty
Item label
Amount
* In case of EAN with all add-on codes
*
Amount for all add-on codes
Total
5-digit add-on code
2-digit add-on code
Amount
• Sample Z report
The subsequent printout occurs in the same
format as in the sample X report.
Note
The EAN codes are printed out in the sequence shown below.
EAN-13
EAN-8
UPC-A
UPC-E
110
Reading and resetting of sales information for EANs associated with an
individual department
• Sample X report
• Sample Z report
Associated dept. code
EAN code
Item label
Sales q'ty and total
The subsequent printout occurs in the same
format as in the sample X report.
Reading of EANs whose sales
amounts are zeros
Reading of EANs whose sales
amounts are zeros (by associated
department)
Associated
dept. code
111
Reading of commission sales
information
Commission
sales 1 amount total
Non-commission
sales amount
Transaction reading
Total in drawer reading
Exchange 1 counte
Currency
exchange 1
total
In this report the same transaction data as those
printed when full reading is taken are printed
except department sales totals.
Domestic
currency for
currency
exchange 1
total
Cash in drawer
Cheque in drawer
Cash/Cheque
in drawer
112
Reading and resetting of a stacked report
You can print multiple X1/Z1 reports in sequence at a time.
In this case, you need to program in advance what X1/Z1 reports should be printed in the stacked report
sequence.
Note
The following job code numbers alone can be used for stacked report printing.
Job code number: 100, 107, 109, 110, 113, 120, 127, 129, 130, 131, 132, 140, 150, 160
Refer to “Selection of X1/Z1 and X2/Z2 reports to be printed in the stacked report sequence” for
details.
Deleting of non-accessed EANs
• Sample X report (Reading)
• Sample Z report (Deleting)
EAN code
Item label
The subsequent printout occurs in the same
format as in the sample X report.
Periodic sales*
*: When there is any sales data of the EAN for #209 report, the data is printed here.
When you delete the EAN in Z1 mode under this situation, the data for #209 is also deleted.
113
3 Periodic consolidation
Your register allows you to take consolidation X and Z reports of a chosen period (normally one week or a
month).
Generality
The periodic reading or resetting reports are the same in format as those in the X1/Z1 report for daily total
except job code no. (#2xx) and mode indication (“X2” or “Z2”.)
• Sample X report
• Sample Z report
Reset symbol
Read symbol
Reset counter
of daily total
Reset counter
of periodic
consolidation
Grand total
The subsequent printouts are the same in format as
those in the X/Z report for daily total.
114
Reading and resetting of the daily net totals
• Sample X report
• Sample Z report
The subsequent printout occurs in the
same format as in the sample X report.
Reading and resetting of a stacked report
You can print multiple X2/Z2 reports in sequence at a time.
In this case, you need to program in advance what X2/Z2 reports should be printed in the stacked report
sequence.
Note
The following job code numbers alone can be used for stacked report printing.
Job code number: 200, 207, 209, 210, 213, 220, 227, 229, 230, 231, 232, 240, 250, 270
Refer to “Selection of X1/Z1 and X2/Z2 reports to be printed in the stacked report sequence” for
details.
115
COMPULSORY CASH/CHEQUE
DECLARATION
If you want to make mandatory the declaration of the cash and cheque amount in the drawer before
outputting cashier Z reports, consult your dealer and have your register programmed for compulsory
cash/cheque declaration.
If your register is programmed for compulsory cash/cheque declaration (CCD), a cashier must first count and
declare the cash and cheque amounts (of domestic and foreign currency) in the drawer, before he or she can
output a cashier report. The procedure for outputting a CCD report is shown below.
Types of compulsory cash/cheque declaration
• Compulsory declaration prior to individual cashier resetting
• Compulsory declaration prior to full cashier resetting
Note
• Compulsory cash/cheque declaration is available in the above two types. You can choose either
of these. Consult your dealer for details.
• When cash/cheque declaration is compulsory, flash reports are not available.
Key operation
After the first ; key is pressed, the register prompts the cashier to input the cash and cheque accounts for
both domestic and foreign currency. The cashier can simply input the total amounts of each currency unit, or the
number of bills or coins of each denomination of each currency unit.
• Individual cashier report
OP X/Z mode
51
. ≈
The drawer opens and the cashier is prompted to
enter the cash and cheque amounts. (“ ” is displayed.)
Input the cheque or
currency denomination
=
[ “
X1/Z1 mode
151
. ≈
;
Q'ty
≈
X
?
to
Amount
=
[ “
to
• Full cashier report
X1/Z1 mode
150
. ≈
Input the total
amount of cash
or cheques
Cancel
previous
entry
To repeat
:
To display cash/cheque subtotal
= :When inputting the cash or cheque amount (domestic currency) in the drawer
[ to “ :When inputting the amount of a foreign currency in the drawer
116
;
CCD entry amount
Currency exchange 1 cash in drawer to be obtained
Total of entered (declared) exchange 1 in drawer
Difference
Cash in drawer to be obtained
Cheque (in domestic currency) in drawer to be obtained
Cash/cheque in drawer to be obtained
Total of entered (declared) cash/cheque in drawer
Difference
Total of difference
Change total for cheque tendering
117
PROGRAMMING FOR EURO
Your register can be modified to correspond with each period set for the introduction of EURO, and in your
register each currency is treated as shown on the table below depending on which period you are in.
Basically your register can be automatically modified to correspond to the introduction of EURO by executing the
operation of Job #800 in X2/Z2 mode. However, there are several options you must set depending on your
needs.
How currencies are treated in your register
Currency
Period 1
Period 2
Period 3
After the introduction of
EURO, and before EURO
banknotes and coins begin to
circulate
After EURO banknotes and
coins begin to circulate, and
before national currency is
withdrawn from circulation.
(Co-existence of EURO and
national currency)
After the national currency is
withdrawn from circulation
EURO
Exchange 1
Domestic currency
Domestic currency
National currency
(DM, F, etc.)
Domestic currency
Exchange 1
Foreign currency
Exchange 2 to Exchange 4
Exchange 2 to Exchange 4
Exchange 1 to Exchange 4
Receipt samples:
Period 1
Sales total amount in national currency (as domestic currency)
Sales total amount in EURO*
Tendered amount in national currency
Change in national currency
Change in EURO*
*: They are printed for information purposes only.
Period 2
Sales total amount in EURO (as domestic currency)
Sales total amount in national currency*
Tendered amount in EURO
Change in EURO
Change in national currency*
*: They are printed for information purposes only.
Period 3
118
Automatic modification of register system for introduction of EURO
800
X2/Z2
To make your register correspond to the introduction of EURO, your register system can be automatically
modified when the procedure shown below is executed in the X2/Z2 mode. According to the steps of the
introduction, you can make your register correspond to EURO.
Procedure
800
.
≈
*A(1,2 or 3)
;
*A=1: Applicable for the period 1
*A=2: Applicable for the period 2
*A=3: Applicable for the period 3
Note
• You can perform the each operation only once with the substitution of “A=1”, “A=2” and “A=3”. If
you performed the operation with the substitution of “A=2” first, you cannot perform the operation
with the substitution of “A=1”. If you performed the operation with the substitution of “A=3” first,
you cannot perform the operation with the substitution of “A=1” and “A=2”.
The details of the register system modification are as follows:
When “1” is substituted to “A”:
1. Issuing a general Z1 report (Job #100)
2. Issuing a general Z2 report (Job #200)
3. Setting “Yes” for a PGM function “Printing exchange 1 total amount and change amount on receipt and
journal” (Job #2616)
4. Setting “Division” for a PGM function “Exchange 1 calculation method” (Job #2616)
5. Setting the EURO symbol (Ÿ) for the currency description text (Job #2334), and setting “2” for the number of
digits after decimal point (Job #2330) of exchange 1
6. Setting the round-off function enable for currency exchange
After the execution of the procedure with the substitution of “1”, treat EURO as foreign currency using Exchange
1 ([).
When “2” is substituted to “A”:
Issuing a general Z1 report (Job #100)
Issuing a general Z2 report (Job #200)
Resetting GT1, GT2, GT3 and training GT
Converting the unit prices of Dept, PLU and EAN to EURO currency.
Setting “Yes” for a PGM function “Printing exchange 1 total amount and change amount on receipt and
journal” (Job #2616)
6. Setting “Multiplication” for a PGM function “Exchange 1 calculation method” (Job #2616)
7. Changing the domestic currency symbol to the EURO symbol (Ÿ) and setting the number of digits after
decimal point of the domestic currency to 2
8. For the setting of the currency description text and the number of digits after decimal point of exchange 1,
the ones that had been set to the domestic currency are set. (Job #2330 and #2334)
9. Setting the round-off function enable for currency exchange
1.
2.
3.
4.
5.
Note
When any special setting has been applied for the rounding system to make it suit your domestic
(national) currency, the setting is cancelled to make it suit your new domestic currency, EURO.
119
After the execution of the procedure with the substitution of “2”, treat EURO as domestic currency, and national
currency as foreign currency using Exchange 1 ([).
With the execution of the procedure with the substitution of “2”, your domestic currency becomes EURO. While
unit prices of departments, PLUs and EANs are automatically converted to EURO currency, you must change
the rates or amounts for the miscellaneous keys so that they are based on amounts in EURO.
When “3” is substituted to “A”:
1. Issuing a general Z1 report (Job #100)
2. Issuing a general Z2 report (Job #200)
3. Resetting GT1, GT2, GT3 and training GT
4. Converting the unit prices of Dept, PLU and EAN to EURO currency.
5. Setting “No” for a PGM function “Printing exchange 1 total amount and change amount on receipt and
journal” (Job #2616)
6. Setting “Multiplication” for a PGM function “Exchange 1 calculation method” (Job#2616)
7. Changing the domestic currency symbol to the EURO symbol and setting the number of digits after decimal
of the domestic currency to 2
8. Setting the round-off function enable for currency exchange
Note
When the operation is performed from the status of substitution “1”, and when any special setting
has been applied for the rounding system to make it suit your domestic (national) currency, the
setting is cancelled to make it suit your new domestic currency, EURO.
After the execution of the procedure with the substitution of “3”, treat EURO as domestic currency.
When the operation with the substitution of “2” has been performed already, “3. Resetting GT1, GT2, GT3 and
training GT” and “4. Converting the unit prices of Dept, PLU and EAN to EURO currency” are not executed.
When the operation with the substitution of “1” or “2” has been performed already, the currency description text
of exchange 1 is overwritten with a space.
Optional programming for the introduction of EURO
PGM 1
PGM 2
Programming relating with the function of exchange 1([) cannot be changed automatically with the execution
of Job #800 described in the previous section. After the execution on each period, conduct the following
programming depending on your needs.
Programming for Exchange 1 ([)
Currency exchange rate (Job #1310)
For the period 1 and period 2, set the EURO conversion rate.
Cheque/credit operation (Job #2616)
Assigning the drawer number to the drawer for foreign currency (Job #2680)
It may be convenient to have two drawers for EURO (as domestic currency) and national currency (as the
foreign currency set in exchange 1) when both of these currencies are co-existing (period 2). In this case,
conduct this programming.
120
OVERRIDE ENTRIES
Programmed limit for functions (such as for maximum amounts) can be overridden by making an entry in the
MGR mode.
Procedure
1.
2.
Turn the mode switch to the MGR position.
Make an override entry.
Example
On this example, the register has been programmed not to allow deduction entries over
2.00.
Key operation
REG-mode
entries
Print
1500 2
250 - ...Error
c
Turn the mode switch
to the MGR position.
250 Return the mode switch
to the REG position.
;
121
CORRECTION AFTER FINALIZING A
TRANSACTION
(AFTER GENERATING A RECEIPT)
When you need to void incorrect entries that cashiers cannot correct (incorrect entries that are found after
finalizing a transaction or cannot be corrected by direct or indirect void), follow this procedure in the MGR mode.
1.
2.
3.
Turn the mode switch to the MGR position.
Press the ? key to put your register in the VOID mode.
Repeat the entries that are recorded on an incorrect receipt. (All data for the incorrect receipt are removed
from register memory; the voided amounts are added to the void register totalizer.)
Incorrect receipt
Note
122
Cancellation receipt
Your machine leaves the VOID mode whenever a transaction is cancelled (i.e. finalized in the VOID
mode.) To void additional transactions repeat steps 2. and 3. above.
FOR THE OPERATOR
PRIOR TO ENTRIES
1 Preparations for entries
Before registrations, insert the operator key into the mode switch and turn it to the REG position and check the
following items:
Receipt and journal paper rolls
If the receipt and journal paper rolls are not set in the machine or there are low rolls, install new ones according
to section “4. Installing and removing the paper rolls” under “OPERATOR MAINTENANCE.”
Receipt ON/OFF function
You can disable receipt printing in the REG mode to save paper using the receipt function. To disable receipt
printing, press the q key in the OP X/Z position. This key toggles the receipt printing status ON and OFF.
To check the receipt printing status, turn the mode switch to the OP X/Z position or press the c key in the REG
mode. When the function is in the OFF status, the receipt off indicator “_” illuminates.
Your register will print reports regardless of the receipt state. This means that the receipt roll must
be installed even when the receipt state is “OFF”.
Note
Cashier and clerk assignment
✱
✱
Prior to any item entries, cashiers must enter their cashier codes into the register, and may also be required to
enter a clerk code. However, these code entries may not be necessary when the same cashier or clerk code is
used in the next transaction.
Cashier codes and clerk codes are available in two variants: Variant 1, in which they are displayed (“-00-” to
“-99-”), and Variant 2, in which they are not displayed (always “-00-”).
When the cashier or clerk code is assigned by the following procedure, the register prints the two-digit cashier
code or clerk code (variant 2: “
”) and the cashier or clerk name both on the receipt and journal for every
transaction.
All of these settings depend on how the register has been programmed. For the selection of these
settings, consult your local dealer.
Note
✱
✱
Cashier code
(“
” is printed in Variant 2.)
Clerk code
” is printed in Variant 2.)
Clerk name
✱
✱
(“
Cashier name
123
Procedure
Cashier assignment
■ Sign-on
■ Sign-off
Variant 1 / Variant 2 :
To display the signed-on cashier code
Variant 1 :
Cashier code
(Code is displayed)
Variant 2 :
(Code is not displayed)
Note
‹
‹
‹
‹
‹
Cashier code
The real cashier key system is also available. In this system put one of the 1 through 15 keys in the
cashier switch to sign on. If you want to choose this system, consult your dealer.
Clerk assignment
■ Sign-on
■ Sign-off
Variant 1 / Variant 2 :
To display the signed-on clerk code
Variant 1 :
Clerk code
(Code is displayed)
Variant 2 :
(Code is not displayed)
Note
^
Clerk code
^
^
^
^
• On the current factory setting, only the entry of the cashier code is required. When cashier & clerk
codes entries are desirable for your register, consult your dealer.
• If you want to enter cashier and/or clerk codes before every transaction, consult your dealer.
• For the display type selection of cashier code and clerk code, “Variant 1” has been preset. For the
selection of “Variant 2,” consult your dealer.
• Clerk can be changed during the transaction. Consult your dealer.
2 Error warning
In the following examples, your register will go into an error state accompanied with a warning beep and the
error symbol “ ” on the display. Clear the error state by pressing the c key and take proper action.
Please refer to the error code table on page 158.
• When you enter an over 32-digit number (entry limit overflow): Cancel the entry and re-enter a correct number.
• When you make an error in key operation: Clear the error and continue operation.
• When you make an entry beyond a programmed amount entry limit: Check to see if the entered amount is
correct. If it is correct, it can be rung up in the MGR mode. Contact your manager.
• When an including-tax subtotal exceeds eight digits: Delete the subtotal by pressing the c key and press the
;, Å, ( through +, or ] through ’ key to finalize the transaction.
124
ENTRIES
1 Item entries
Single item entries
Procedure
Department entries (direct department entries)
Enter a unit price and press a department key. If you use a programmed unit price, press a department key only.
When using a programmed unit price
*Less than the programmed upper limit amounts
Unit price *
(max. 8 digits)
Note
Department key
When those departments for which the unit price has been programmed as zero (0) are entered,
only the sales quantity is added.
Department entries (indirect department entries)
When using a programmed unit price
*Less than the programmed upper limit amounts
Unit price *
(max. 8 digits)
å
Dept. code
(1-50)
à
PLU entries (indirect PLU entries)
Enter a PLU code and press the ß key.
PLU code
Note
ß
When those PLUs for which the unit price has been programmed as zero (0) are entered, only the
sales quantity is added.
Subdepartment (open PLU) entries
Unit price *
(max. 8 digits)
å
PLU code
ß
*Less than the programmed upper
limit amounts
PLU entries (direct PLU entries)
When using a programmed price
Unit price
(for subdept.)
Direct PLU key
EAN entries
Scan EAN code
Ä
EAN code
(max.18 digits)
Û
* After scanning an EAN code or pressing the Û key, you
may be requested to enter a unit price with the display
“------”. In this case, enter the unit price and press the
å key.
125
Example
Key operation
Print
1200 3
5
8à
680 å 5 à
2ß
1200 å 11 ß
ô
5012345678900 Û
;
Repeat entries
You can use this function for entering a sale of two or more same items.
You can use the è key to repeat entry instead of department, à, direct PLU, ß or Û key.
Example
Key operation
Repeated
department
entry (direct)
Repeated
department entry
(indirect)
Repeated PLU
entry
(indirect)
Repeated PLU
entry
(direct)
Repeated
subdepartment
entry
Repeated EAN
entry
Repeated
department entry
(direct) using the
repeat key
126
Print
200 8
8
8
680 å 5 à
à
10 ß
ß
ß
ó
ó
500 å
60 ß
ß
5012345678900 Û
Û
600 2
è
è
;
Multiplication entries
Use this feature entry method when you need to enter two or more same items.
This feature helps when you sell a large quantity of items or need to enter quantities that contain decimals.
Procedure
When you use a programmed
unit price
Q'ty
≈
Unit price
Department key
PLU code
å
ß
Unit price
Direct PLU
Unit price
Unit price
å
Dept. code
Dept. entry (direct)
à
Dept. entry (indirect)
PLU entry (indirect)
PLU/subdept. entry (direct)
PLU code
ß
Subdept. entry
Scan EAN code
EAN code
Ä
Û
EAN entry
EAN entry
• After scanning an EAN code or pressing the Û key, you may be requested to enter a unit price with the
display “------”. In this case, enter the unit price and press the å key.
• Q'ty: Up to four digits integer + three digits decimal
• Unit price: Less than a programmed upper limit
• Q'ty x unit price: Up to eight digits
Example
Key operation
Department
entry (direct)
Department
entry
(indirect)
PLU entry
Direct PLU
entry
Subdepartment
entry
EAN entry
Print
7.5≈
165 8
2≈
250 å
5à
15 ≈
13 ß
8 . 25 ≈
ò
3≈
100 å
60 ß
5≈
5012345678900 Û
;
127
Successive multiplication entries
This function is practical for example when you enter a sale of items sold by area (square meter).
Procedure
When you use a programmed
unit price
≈
Length
≈
Width
Unit price
PLU code
å
ß
Unit price
per m2
Direct PLU
Unit price
Unit price
per m2
Dept.code
å
Department key
à
Dept. entry (direct)
Dept. entry (indirect)
PLU entry (indirect)
PLU/subdept. entry (direct)
PLU code
ß
Subdept. entry
Scan EAN code
EAN code
Ä
Û
EAN entry
EAN entry
• After scanning an EAN code or pressing the Û key, you may be requested to enter a unit price with the
display “------”. In this case, enter the unit price and press the å key.
• Length or width: up to seven digits (4-digit integer + 3-digit decimal)
• Unit price: less than a programmed upper limit
• Length x Width x Unit price: up to eight digits
Note
For actual use of this function, consult your dealer.
Example
Key operation
Department entry
PLU entry
Subdepartment entry
EAN entry
Print
3≈
4≈
400 5
1.5≈
2.5≈
8ß
1 . 75 ≈
1 . 75 ≈
600 å
6ß
4≈
5≈
5099887654302 Û
;
128
Split-pricing entries
You will use this function when your customer wants to purchase items normally sold in bulk.
Procedure
When you use a programmed
unit price
≈
Selling q'ty
Base q'ty
≈
Unit price
per base q'ty
Unit price
PLU code
Unit price
per base q'ty
Unit price
per base q'ty
Department key
å
ß
Dept.code
à
PLU code
ß
Direct PLU
å
Scan EAN code
EAN code
Only when you use a
base q'ty programmed
for PLU code
PLU code
Unit price
per base q'ty
Unit price
per base q'ty
Ä
Û
ß
Direct PLU
å
PLU code
ß
Scan EAN code
Only when you use a
base q'ty programmed
for EAN code
EAN code
Ä
Û
• After scanning an EAN code or pressing the Û key, you may be requested to enter a unit price with the
display “------”. In this case, enter the unit price and press the å key.
• Selling quantity: Up to four digits integer + three digits decimal
• Base quantity: Up to two digits (integer)
Note
For actual use of this function, consult your dealer.
Example
Key operation
Department
entry
PLU entry
EAN entry
Print
7≈
10 ≈
600 7
8≈
5≈
35 ß
5≈
6≈
5045678912304 Û
;
129
Single item cash sale (SICS)/single item finalize (SIF) entries
SICS entries
• This function is useful when a sale is for only one item and is for cash; such as a pack of cigarettes. This
function is applicable only to those departments that have been set for SICS or to their associated PLUs,
subdepartments or EANs.
• The transaction is finalized and the drawer opens as soon as you press the department key, à key, ß
key , the direct PLU key or Û key.
Example
Key operation
Print
250
9
For finishing
the transaction
Note
If an entry to a department, PLU/subdepartment or EAN set for SICS follows the ones to
departments, PLUs/subdepartments or EAN not set for SICS, it does not finalize and results in a
normal sale.
SIF entries
• If an entry to a department, PLU/subdepartment or EAN set for SIF follows the ones to departments,
PLUs/subdepartments or EANs not set for SIF, the transaction is finalized immediately as a cash sale.
• Like the SICS function, this function is available for single-item cash settlement.
Example
Key operation
Print
1745 8
1500
9
For finishing
the transaction
Link PLU/EAN link entries
In case that you register a PLU or EAN that has any PLU linked with the PLU or EAN, the linked PLU(s) are
automatically registered together with the leading link PLU or EAN when it is registered. The print format on the
receipt depends on the programming (#2616) as described below.
Printing detailed information
The description texts and amounts of the leading link PLU/EAN and the linked PLUs are printed individually.
Example
(In case of link PLU)
Key operation
Print
21 ß
;
130
Linked PLUs
Printing leading link PLU/EAN and total sales amount
The description text of the leading link PLU/EAN and the total sales amount of the leading link PLU/EAN and the
linked PLUs are printed.
Example
(In case of link PLU)
Key operation
Print
21 ß
Total amount
;
Note
If a discount entry is made for a link PLU/EAN link, the discount amount is calculated based on the
total sales amount. The discount itself is given to the leading link PLU/EAN.
EAN learning function
When you enter or scan an undefined code, you are required to enter its unit price and the associated
department. The code, associated department and unit price entered are stored in the EAN file and used for
future EAN sales entries.
Note
• When there is no capacity remained in the file, the data is not stored in the file.
• For the text for the EAN code, the text of its associated department is applied.
• You can use the EAN learning function in the training mode. This may be convenient to practice
the scanning system.
Procedure
“-- ------” is displayed and
beep sound is heared three times.
Scan an undifined EAN code
Ä
Undifined
EAN code
Û
When the unit price is zero, or in case of
non-PLU type EAN code having price info.
or press code.
*
Ì
Unit price
Department key
å
c
Dept. code
à
To cancel the operation
Unit price entered
is displayed
* Press the Ì key when you want to exempt the EAN code entered from the non-accessed EAN delete
function (deletion by executing #105 in Z1 mode).
Note
For the repeat entry, use the è key.
Example
“-- ------” is displayed.
Key operation
Print
5056789123404 Û
750
5
;
131
Price inquiry (view) function (for EANs)
You can use this function when you want to know the unit price of the EAN item during transaction in the
REG/MGR mode.
Procedure
Scan EAN code
The total sales amount of
the EAN is displayed.
Ä
Numeric entry
Ù
(Q'ty
≈
)
Û
EAN code
*1
c
å
*2
*3
(MGR mode) Unit price
å
*1: Press the c key to cancel the the inquiring (view) mode.
*2: Press the å key when you want to register the unit price of the EAN displayed.
*3: You can change the unit price temporarily in the MGR mode. The unit price which is programmed in PGM
mode is not changed (Price override entry).
Note
For the repeat entry, use the è key.
Example
Key operation
Print
5ß
“----” is displayed.
Price is displayed.
132
Ù
5089123456708 Û
å
;
Price change function (for EANs)
Note
To use this function, consult your dealer.
You can use this function when you need to change the unit price or associated department of an EAN item in
REG/MGR mode.
There are two methods for change:
1. Price change mode
You can change the preset price and/or the associated department of an EAN item without entering PGM
mode.
2. Changing price during a transaction
When you has found a wrong EAN price and/or associated department upon transaction, you can correct
them at the time of transaction. With the entry of new price and/or associated department, the preset price
and/or associated department is automatically changed to the new price and/or associated department.
Note
For the Non-PLU type EAN codes having price info. and press codes, the prices in the codes have
the priority over the preset prices. So, for these codes, a changed price is valid only when price
change is executed.
Procedure
Price change mode
“-- ------” is displayed.
“PC--------” is displayed.
Scan EAN code
Ä
Ê
EAN code
Û
Ê
To change the unit price only
To enter 0
Unit price
To change the associated dept.
directly by depressing the
corresponding key
Department key
c
å
To cancel the mode
Dept code
à
To change the associated dept.
using the dept. code entry key
Changing price during a transaction
Scan EAN code
Ä
EAN code
Û
Ê
Ê
To change the unit price only
To enter 0
Unit price
c
To cancel
To change the associated dept.
directly by depressing the
corresponding key
Department key
å
Dept code
à
To change the associated dept.
using the dept. code entry key
133
Example
• Price change mode
Key operation
Print
Ê
5087654321106 Û
Ê
• Changing a price during a transaction
Key operation
Print
5087654321106 Û
Ê
600 Ê
;
The journal printer prints the
following format in this position.
Associated dept. no.
Note
134
• When an undefined code is entered in the price change mode, the register goes to an error status.
• When you press the Ê key during a transaction, the EAN entry is voided of the 1st depression of
the Ê key, then you are allowed to enter a correct price and/or associated department.
• When an associated department is changed, the item label for the department will be also
changed automatically to the item label of new associated department.
• For the repeat entry, use the è key.
2 Displaying subtotals
Your machine provides the following two types of subtotals:
Normal subtotal
This is a subtotal which is displayed by pressing the : key. When you press it, the subtotal of all entries which
have been made is displayed and the symbol “ ” will light up in the display.
Example
Key operation
Print
100 9
100 2
700 3
:
;
Note
Subtotal will not be printed on a receipt on the current factory setting. If you want to print it, consult
your dealer.
Difference subtotal (Differ ST)
This is a subtotal which is printed by pressing the ÷ key. You can get two or more difference subtotals in one
transaction.
When you press it first, the difference subtotal of all entries which have been made is displayed and printed. If
you press it second, you will get the difference subtotal of entries which have been made after you last got it.
Taxes are calculated each time you press the ÷ key, and taxes and taxable subtotals are printed on the receipt
according to the programming (job #2616).
Example
Key operation
Print
100 9
200 2
÷
700 3
;
135
3 Finalization of transaction
Cash or cheque tendering
Press the : key to get a subtotal, enter the amount tendered by your customer, then press the ; or Å key if
it is a cash tender or press one of the ( through + key if it is a cheque tender. When the amount tendered is
greater than the amount of the sale, your register will show the change due amount and the symbol “ ” will light
up. Otherwise your register will show a deficit and the symbol “ ” will light up. Make a correct tender entry.
Example
Cash tendering
Key operation
Print
:
1000 ;
Cheque tendering
Key operation
Print
:
1000 (
Mixed tendering (cheque + cash)
Example
Key operation
Print
:
1000 (
500 ;
Cash or cheque sale that does not need any tender entry
Enter items and press the ; or Å key if it is a cash sale or press one of the ( through
sale. Your register will display the total sale amount.
Example
Key operation
+ if it is a cheque
Print
300 6
10 ß
;
In the case of cheque sale
136
Credit sale
Enter items and press the corresponding credit keys (] through ’).
Key operation
Example
Print
2500 6
3250 7
]
Amount tendering operations (i.e., change calculations) can be achieved by the ] through ’ key when a
PGM2 programming allows them.
Mixed-tender sale (cash or cheque tendering + credit tendering)
Example
Key operation
Print
:
950 ;
}
Note
Press one of the ( through + keys or the ] through ’ keys in place of the ; key when
your customer makes payment in cheques or by credit account.
4 Computation of VAT (Value Added Tax)/tax
VAT/ tax system
The machine may be programmed for the following six tax systems by your dealer.
Automatic VAT 1-6 system (Automatic operation method using programmed percentages)
This system, at settlement, calculates VAT for taxable 1 through 6 subtotals by using the corresponding
programmed percentages.
Automatic tax 1-6 system (Automatic operation method using programmed percentages)
This system, at settlement, calculates taxes for taxable 1 through 6 subtotals by using the corresponding
programmed percentages, and also adds the the calculated taxes to those subtotals, respectively.
Manual VAT 1-6 system (Manual entry method using programmed percentages)
Procedure
:
◊
This system provides the VAT calculation for taxable 1 through 6 subtotals. This calculation is performed using
the corresponding programmed percentages when the ◊ key is pressed just after the : key.
137
Manual VAT 1 system (Manual entry method for subtotals that uses VAT 1 preset percentages)
Procedure
To use a programmed rate
:
VAT rate
◊
This system enables the VAT calculation for the then subtotal. This calculation is performed using the VAT 1
preset percentages when the ◊ key is pressed just after the : key. For this system, the keyed-in tax rate can
be used.
Manual tax 1-6 system (Manual entry method using preset percentages)
Procedure
:
◊
This system provides the tax calculation for taxable 1 through 6 subtotals. This calculation is performed using
the corresponding programmed percentages when the ◊ key is pressed just after the : key.
After this calculation, you must finalize the transaction.
Automatic VAT 1-3 and automatic tax 4-6 system
This system enables the calculation in the combination with automatic VAT 1 through 3 and automatic tax 4
through 6. The combination can be any of VAT1 through VAT3 corresponding to taxable 1 through taxable 3 and
any of tax 4 through 6 corresponding to taxable 4 through taxable 6 for each item. The tax amount is calculated
automatically with the percentages previously programmed for these taxes.
Note
• A PLU/EAN not programmed for any of the tax statuses is registered depending on the tax status
of the department which the PLU/EAN belongs to.
• VAT/tax assignment can be printed at the fixed right position near the amount on the receipt as
follows:
VAT1/tax1
A
VAT2/tax2
B
VAT3/tax3
C
VAT4/tax4
D
VAT5/tax5
E
VAT6/tax6
F
When the multiple VAT/tax is assigned to a department, a PLU or an EAN, a smaller number of the
VAT/tax will be printed. For details, contact your authorized SHARP dealer.
Example
Key operation
(When the manual
VAT 1-6 system
is selected)
138
Print
550 4
:
◊
;
VAT shift entries
This feature is intended to shift the tax status of a particular department (PLU or EAN) programmed for taxable 1
or taxable 1 and taxable 3.
1. When the VAT shift entry is made for a particular department, PLU or EAN programmed for taxable 1, their
tax status shifts to taxable 2.
2. When this entry is made for a particular department (PLU or EAN) programmed for taxable 1 and taxable 3,
the tax status “taxable 1” remains unchanged, but the other “taxable 3” is ignored.
Procedure
Press the „ to activate the VAT shift prior to entering department(s), PLU(s) or EAN(s) concerned.
Example
Key operation
(When the manual
VAT 1-6 system
is selected.)
Print
„
550 4
:
◊
;
5 Auxiliary entries
Percent calculations (premium or discount)
• Your register provides the percent calculation for the subtotal or each item entry depending on the
programming.
• Percentage: 0.01 to 99.99%
Percent calculation for the subtotal
Example
Key operation
(When a discount
of 10% is
programmed for
the
key)
∞
Print
4≈
140 5
225 7
7
:
∞
;
139
Percent calculation for item entries
Example
Key operation
(When a premium
of 15% is
programmed for
the
key)
§
Print
800 6
§
90 ß
7.5§
;
Deduction entries
Your register allows you to deduct a certain amount less than a programmed upper limit after the entry of an
item or the computation of subtotal depending on the programming.
Deduction for the subtotal
Example
Key operation
Print
575 6
80 ß
:
100 –
;
Deduction for item entries
Example
Key operation
Print
675 7
75 -
;
Refund entries
For a refund entry, press the © key just before you press a department key, à key, direct PLU key, ß
key or Û key or just before you scan an EAN code. The operation before pressing the © key is the same as
the one of normal operation. For example, if a refund item is the one entered into a department, enter the
amount of the refund, then press the © key and the corresponding department key in this order; if an item
entered into a PLU is returned, enter the corresponding PLU code, then press the © and ß keys; and if a
refund item is the one entered into an EAN, press the © key and scan the EAN code.
140
Example
Key operation
Print
250 © 6
300 å 5 © à
7 ≈ 13 ©ß
5089123456708
©Û
;
Printing of non-add code numbers
Enter a non-add code number such as a customer's code number and credit card number within a maximum of
16 digits and press the = key at any point during the entry of a sale. Your register will print it at once.
Example
Key operation
Print
1230 =
1500 6
]
6 Payment treatment
Currency exchange
Your register allows payment entries of foreign currency. Pressing one of the [ through ” key creates a
subtotal in foreign currency.
Procedure
For an additional payment in foreign currency
After an entry
is completed
or
After the amount
tendered is found
smaller than the
sales amount in
a sales entry
For direct finalization
Preset exchange rate
*Exchange rate
[
{
“
”
Amount
tendered
(max. 8 digits)
;
Å
( +
] ’
to
to
c
Next registration or
payment in domestic currency
Reentry
*Exchange rate: 0.000000 to 999.999999
Note
• When the amount tendered is short, the deficit is shown in domestic currency.
• Availability of credit and cheque tendering depends on the programming (#2616) (only for
exchange 1).
141
Example
Preset exchange rate (1.550220) - EX1
Key operation
Print
2300 6
4650 7
Currency
exchange
[
15000 ;
Amount
tendered in
foreign currency
Domestic
currency
Exchange rate
Foreign currency
Domestic
currency
Currency description text
Manual exchange rate - EX4 (The ” key can be used only for the manual entry of an
exchange rate.)
Key operation
Print
2300 6
4650 7
1 . 0190 ”
10000 ;
Received on account entries
Procedure
Amount
(max. 8 digits)
r
®
or
Example
;
(
]
or
through
through
Å
+
’
Key operation
Print
12345 =
4800 r
(
Paid out entries
Procedure
Amount
(max. 8 digits)
142
p
π
or
;
(
]
or
through
through
Å
+
’
Example
Key operation
Print
6789 =
3000 p
(
No sale (exchange)
Simply press the n key without any entry. The drawer will open and the printer will print “NO SALE” on both
the journal and the receipt. If you let your machine print a non-add code number before pressing the n key, a
no sale entry is achieved with a non-add code number printed.
Cashing a cheque
Enter the cheque amount, then press one of the ( through + key.
Procedure
Non-add code
number
Example
=
Cheque
amount
(
through
+
Key operation
Print
6789 =
3000 (
7 Automatic sequencing key (` key) entries
You can achieve a programmed transaction simply by pressing a corresponding automatic sequencing key.
Example
(¡ = 500 7 ;)
Key operation
Print
¡
143
CORRECTION
1 Correction of the last entry (direct void)
If you make an incorrect entry relating to a department, PLU/subdepartment, EAN, percentage (∞ through •),
deduction (- through ≠) or refund, you can void this entry by pressing the ? key immediately after the
incorrect entry.
Example
Key operation
Print
1250 6
?
2ß
?
5012345678900 Û
?
600 8
§
?
328 9
28 ?
250 © 6
?
;
2 Correction of the next-to-last or earlier entries (indirect void)
With the ? key, you can void any incorrect department, PLU/subdepartment, EAN or item refund entry made
during a transaction if you find it before finalizing the transaction (e.g. pressing the ; key). This function is
applicable to department, PLU/subdepartment, EAN and item refund entries only.
For the operation, press the ? key just before you press a department key, à key, direct PLU key, ß
key or Û key or just before you scan an EAN code. For the refund indirect void, press the ? key after you
press the © key.
Example
Key operation
Print
1310 6
1755 7
10 ß
ô
58 ß
825 7
5012345678900 Û
1310 ? 6
?ô
58 ? ß
5012345678900 ?
144
Û
;
3 Subtotal void
You can void an entire transaction. Once subtotal void is executed, the transaction is aborted and the register
issues a receipt.
Example
Key operation
Print
1310 2
1755 6
10 ß
35 ß
Subtotal void
:
?
:
Correction of incorrect entries not handled by the direct or indirect void
4 function
Any errors found after the entry of a transaction has been completed or during an amount tendered entry cannot
be voided. These errors must be corrected by the manager.
The following steps should be taken:
1.
2.
3.
If you are making the amount tendered entry, finalize the transaction.
Make correct entries from the beginning.
Hand the incorrect receipt to your manager for its cancellation.
145
SPECIAL PRINTING FUNCTIONS
1 Copy receipt printing
If your customer wants a receipt after you have finalized a transaction with the receipt function being in the
“OFF” status (no receipting), press the q key. This will produce a receipt. Your register can also print a copy
receipt when the receipt function is in the “ON” status. If you want to make a copy, please consult your dealer.
Note
Pressing the q key in the OP X/Z mode before registration toggles the status “ON” and “OFF”.
Example
Printing a copy receipt after making the entries shown below with the receipt function being in
the “OFF” status
Key operation
Print
850 2
3≈
150 1
;
For receipting→
Print on the
journal
q
Print on the
receipt
When the receipt function is in the “ON” status and you press
the q key to make a second copy
When the receipt function is in the “ON” status,
the “ COPY ” symbol will be printed on the receipt.
146
2 Guest check copy
You can use this function when you want to take a copy of guest check.
Press the g key and make a desired entry.
Procedure
g
Item entries
q
Finalization
When the receipt
ON/OFF function is
in the “OFF” status
Note
The guest check copy has nothing to do with the memory.
Example
Key operation
Print
g
1480 2
;
3 Printing of header and footer graphic logos
As a default setting, it is set to print a graphic logo on the top of each receipt (header graphic logo), and another
graphic logo can be printed on the bottom of each receipt (footer graphic logo) with the job code #2616. You can
also print the graphic logos with the combination of 3-line header logo message or 3-line footer logo message, or
can print only logo message without graphic logo. Consult your dealer when you want to change the setting.
• Sample receipt with a header graphic logo and a footer graphic logo
Header graphic logo
Footer graphic logo
147
OVERLAPPED CASHIER ENTRY
This function allows you to switch from one cashier to another and to interrupt the first cashier’s entry. So the
second cashier can do his or her entry in this mode. For actual use of this function, consult your dealer.
Example
Cashier 1: Entry started
Cashier 2: Cashier change (1 to 2), interrupt initiated
Cashier 2: Transaction finished (2)
Cashier 1: Cashier change (2 to 1), entry restart
Note
• When the cashier and clerk system is applied for your register, you cannot operate the overlapped
cashier entry.
• The overlapped cashier entry is not effective while the tendering sale is going on.
• If any cashier is still making an entry (or has not finalized the transaction yet), the machine does
not run in any mode other than REG and MGR and can print no X/Z reports. The error code “E22”
and the corresponding cashier code(s) are displayed at this time.
Key operation
Comments
1. Cashier 1 is assigned.
The entry by cashier 1 is started.
(1‹)
100 1
360 3
3
2. Cashier 2 is assigned.
2‹
3≈
150 2
;
The entry by cashier 2 is started.
(The entry by cashier 1 is interrupted.)
The transaction by cashier 2 is finalized.
3. Cashier 1 is assigned.
1‹
100 1
360 3
;
148
The entry by cashier 1 is restarted.
The transaction by cashier 1 is finalized.
OPERATOR MAINTENANCE
1 In case of power failure
When power is lost, the machine retains its memory contents and all information on sales entries.
• When power failure is encountered in register idle state or during an entry, the machine returned to the normal
state of operation after power recovery.
• When power failure is encountered during a printing cycle, the register
prints “========” and then carries out the correct printing procedure
after power recovery. (See the sample print.)
2 In case of printer error
If the printer runs out of paper, the printer will stall, “PPPPPPPPPP” will appear on the display, and the register
will start to continuously produce an intermittent beeping tone. Key entries will not be accepted. Referring to “5.
Installing and removing the paper roll” in this chapter, install a new roll paper in the proper position, then press
the c key. The printer will print the power failure symbol and resume printing.
If the print head comes up, the printer stalls, “H” will appear on the very left of the display, and the register will
start to continuously produce an intermittent beeping tone. Key entries will not be accepted. Bring back the print
head to the correct position, then press the c key. The printer will print the power failure symbol and resume
printing.
3 Thermal printing
Your register prints by means of thermal printing. The print head applies heat to thermal paper which is
chemically treated to change color when heated to a certain level. This creates the printed text.
Cautions in handling the printer
Printing position
• If you are not going to use the register for an extended
period of time, pull the print head release lever toward you
so that the print head is set apart from the plate.
Head-up position
149
• Avoid the following environments:
Dusty and humid places
Direct sunlight
Iron powder (A permanent magnet and electromagnet are used in this machine.)
• Use the print head release lever only when necessary.
• Never pull the paper when it is in contact with the print head. First release the head with the print head release
lever, and then remove the paper.
• Never touch the surface of the print head.
• Never touch around the print head and the motor during printing or before they have had sufficient time to cool.
Cautions in handling the recording paper (thermal paper)
• Use only the paper specified by SHARP.
• Do not unpack the thermal paper until you are ready to use it.
• Avoid heat. The paper will color at around 70°C.
• Avoid dusty and humid places for storage. Avoid direct sunlight.
• The printed text on the paper can discolor under the following conditions:
Exposure to high humidity and temperature
Exposure to the direct sunlight
Contact with glue, thinner or a freshly copied blueprint.
Heat caused by friction from scratching or other such means.
Contact with a rubber eraser or adhesive tape.
• Be very careful when handling the thermal paper. If you want to keep a permanent record, copy the printed text
with a photocopier.
4 Paper roll near-end sensing function (only for the journal paper) <option>
When the journal paper roll comes near the end or is not loaded, the machine senses this condition and sounds
an alarm, displaying the error code “E04”. At this time, clear the alarm with the c key and replace the paper roll
as soon as possible. The following entry can be made after clearing the alarm. However, since this function
works each time one transaction is completed, the alarm sound will be emitted again as the following transaction
is completed unless the paper roll is replaced.
If you want to use this function, consult your dealer.
• The sensing position depends upon the size of the paper tube.
Therefore, it is advisable to use paper rolls - whose paper tube is
18 mm in O.D. and 12 mm in I.D. - specified by SHARP.
• If the sensing occurs too early or late, contact your dealer.
Paper roll
Paper tube
12 mm
18 mm
150
5 Installing and removing the paper roll
Recording paper specifications
Be sure to use paper rolls specified by SHARP.
The use of any other paper rolls than specified could cause paper jamming, resulting in register malfunction.
Paper specification
Paper width:
44.5 ± 0.5 mm
Max. outside diameter: 80 mm
Quality:
Thermal paper
Paper tube:
18 mm
• Be sure to set paper roll(s) prior to using your machine, otherwise it may cause a malfunction.
Install the paper roll in the printer. Be careful then to set the roll and cut the paper end correctly.
Note
If the top end of the paper roll is fixed with paste or tape, the paper may lose its color development
ability in the pasted or taped area due to the deterioration of the heat-sensitive color development
component of the paper surface. This may result in nothing appearing at this location when printing
is performed. Therefore, when setting a new paper roll in the machine, be sure to cut off
approximately one revolution (approx. 25 cm long).
(How to set the paper roll)
(How to cut the paper end)
To the printer
To the printer
Incorrect
Correct
Correct
Incorrect
Installing the paper roll
Installing the receipt paper roll
1. Turn the mode switch to the “REG” position with the AC cord
connected.
Printing
position
2. Remove the printer cover.
3. Check that the print head release lever is in its printing
position.
4. Set the paper correctly as illustrated above in the receipt
side of the printer.
5. Insert the end of the paper into the paper chute as shown on
the left. It will automatically be fed through the printer.
6. Cut off the excess paper that comes out of the printer with
the manual cutter.
7. Replace the printer cover.
151
Installing the journal paper roll
1. Turn the mode switch to the “REG” position with the AC
cord connected.
2. Remove the printer cover.
3. Check that the print head release lever is in its printing
position.
Printing
position
4. Set the paper correctly as illustrated on the previous page in
the journal side of the printer.
5. Insert the end of the paper into the paper chute as shown
on the left. It will automatically be fed through the printer.
6. Insert the end of the paper into the slit in the paper take-up
spool. (Press the Ô key to feed more paper through if
required.)
7. Wind the paper two or three turns around the spool shaft.
8. Set the spool on the bearing.
9. Replace the printer cover.
Note
• When it is difficult to insert paper into the paper chute, try inserting it again by following the steps described
below.
1. Cut off the end of paper in a single straight cut.
2. Pull the print head release lever toward you to lift up the print
head.
Head-up position
3. Insert the end of paper into the paper chute, while pressing
the corresponding paper feed key (Ô key or ‰ key).
4. When the end of paper comes out of the printer, release the
feed key and return the print head release lever to its original
position.
5. Press the feed key to feed more paper.
Journal paper
feed key
In case of inserting the journal paper roll
• When you want to manually install a new roll of paper while your machine is turned off, follow the steps shown
below:
1. Pull the print head release lever toward you to lift up the print head.
2. Correctly place the new paper roll into the receipt/journal paper roll location.
3. Insert the paper end into the paper chute until it comes out of the printer.
4. Cut or roll the paper onto the take-up spool as described for automatic installation.
5. Return the print head release lever to its original position.
152
Removing the paper roll
When a red dye appears on the paper roll, it is time to replace the existing paper roll. Replace the paper roll
with a new one. If you plan not to use your register for an extended period of time, remove the paper roll, and
store it in the appropriate place.
Removing the receipt paper roll
1. Remove the printer cover.
2. Cut the paper behind the printer and near the paper roll.
3. Press the ‰ key until the paper remaining in the printer
comes out completely.
4. Remove the paper roll from the back of the printer.
Note
Do not pull the paper through the printer.
Removing the journal paper roll
1. Remove the printer cover.
2. Press the Ô key to advance the journal paper until its
Area to cut
printed part is out of the way.
3. Cut the paper and remove the take-up spool.
4. Cut the paper behind the printer and near the paper roll.
5. Press the Ô key until the paper remaining in the printer
comes out completely.
6. Remove the paper roll from the back of the printer.
Note
Do not pull the paper through the printer.
153
7. Remove the outer side of the take-up spool as shown on the
left.
8. Remove the printed journal roll from the take-up spool.
Removing a paper jam
Precaution: Be very careful with the manual cutter, so as not to cut yourself. Never touch the print head
immediately after printing, because the head may still be hot.
1. Remove the printer cover.
2. Pull the print head release lever all the way forward (after it
Pull all the
way forward
154
stops at one position, continue pulling forward until it stops
again and cannot be pulled forward any further).
3. Remove the paper jam. Check for and remove any shreds
of paper that may remain in the printer.
4. Reset the paper roll correctly by following the steps in
“Installing the paper roll”.
5. Return the print head release lever to its original position.
6. Replace the printer cover.
6 Cleaning the print head
When the printed text is getting dark or faint, paper dust may be stuck to the print head. Clean the print head as
follows:
1. Turn the mode switch to the “ ” position.
2. Remove the printer cover.
3. Pull the print head release lever all the way forward (after it
Pull all the
way forward
stops at one position, continue pulling forward until it stops
again and cannot be pulled forward any further).
4. Clean the print head with a soft rag moist with ethyl alcohol
or isopropyl alcohol.
5. Return the print head release lever to its original position
immediately after cleaning.
Print head
6. Replace the printer cover.
Precautions:
Never touch the print head with a tool or anything hard as
it may damage the head.
155
7 Removing the till and the drawer
The till in the register is detachable. After closing your business for the day, remove the till from the drawer and
keep the drawer open. The coin case is also detachable from the till. To detach the drawer, pull it forward fully
with the till removed, and remove it by lifting it up.
Coin case
1
Till
2
Drawer
8 Opening the drawer by hand
The drawer automatically opens in the usual way. However, when power failure is encountered or the machine
becomes out of order, slide the lever located on the machine bottom toward the rear. (See the figure below.)
The drawer will not open, if it is locked with a drawer lock key.
Lever
156
9 Installing the fixing angle bracket
To prevent the register from moving when the drawer opens, the fixing angle bracket is supplied with the
register. By attaching the bracket to the table where the register is installed, you can hook the register on this
bracket and secure the register to its position.
How to install the fixing angle bracket
1. Thoroughly clean the location where the fixing angle
bracket (B) is to be placed.
2. Peel off the adhesive tape on the fixing angle bracket.
3. Hook the angle bracket onto the hook (A) that is
located at the bottom rear of the register.
4. Firmly stick the fixing angle bracket to the table
surface that your cleaned above.
B
A
How to remove the register from the fixing angle bracket
1. Lift up the front of the register and pull the register
towards you.
157
10 Before calling for service
The malfunctions shown in the left-hand column below, labelled “Fault,” do not necessarily indicate functional
faults of the machine. It is therefore advisable to refer to the “Checking” shown in the right-hand column before
calling for service.
Fault
(1) The display won't be illuminated even when
the mode switch is turned to any other
position than “ ”.
(2) The display is illuminated, but the whole machine
refuses registrations.
(3) No receipt is issued.
(4) No journal paper is taken up.
(5) Printing is unusual.
Checking
• Is power supplied to the electrical outlet?
• Is the power cord plug out or loosely connected to the
electrical outlet?
• Is a cashier code assigned to the register?
• Is a clerk code assigned to the register?
• Is the mode switch set properly at the “REG” position?
• Is the receipt paper roll properly installed?
• Is there a paper jam?
• Is the receipt function in the “OFF” status?
• Is the print head release lever at the printing position?
• Is the take-up spool installed on the bearing properly?
• Is there a paper jam?
• Is the print head release lever at the printing position?
• Is the paper roll properly installed?
Error code table
When the following error codes are displayed, press the c key and take a proper action according to the table
below.
Error
code
Error status
E01
E02
E03
E04
E05
E07
Registration error
Misoperation error
Undefined code is entered.
Journal paper is nearly empty.
Secret code error
Memory is full.
Make a correct key entry.
Make a correct key entry.
Enter a correct code, or declare it by the programming.
Replace a journal paper roll with a new one.
Enter a correct secret code.
Expand the file within a capacity of memory.
E11
Compulsory depression of the : key for direct
finalization
Compulsory tendering
Overlapped cashier error
Cashier resetting over error
Compulsory non-add code entry
No entry of your cashier code
The current cashier code should not be changed.
Overflow limitation error
The open price entry is inhibited.
The preset price entry is inhibited.
The direct finalization is inhibited.
Undefined clerk code is entered.
Registration buffer is full.
The drawer is still opened.
Press the : key and continue the operation.
E12
E22
E23
E31
E32
E33
E34
E35
E36
E37
E58
E67
E76
158
Action
Make a tendering operation.
Enter a non-add code.
Make a cashier code entry.
Change a cashier after finalizing the transaction.
Make a registration within a limit of entry.
Make a preset price entry.
Make an open price entry.
Make a tendering operation.
Enter a correct clerk code.
Close the drawer.
LIST OF OPTIONS
For your register, the following options are available.
For details, contact your dealer.
•RAM memory chip model ER-03RA
•Remote drawer model ER-05DW
•Till model ER-58CC and till cover model ER-03CV
•Key kit models
By using the following key kits, you can change the keyboard layout of your register including the
expansion of the number of departments.
ER-11KT7: 30 regular size key kits
ER-12KT7: 30 1 x 2 size key kits
ER-22KT7: 10 2 x 2 size key kits
ER-11DK7G: 30 regular size dummy key kits
ER-51DK7G: 10 5 x 1 size dummy key kits
•Hand scanner model ER-A6HS1
159
SPECIFICATIONS
Model:
Dimensions:
Weight:
Power source:
Power consumption:
Working temperature:
Electronics:
Built-in battery:
Display:
Operator display:
Customer display:
Printer:
Type:
Printing speed:
Printing capacity:
Other functions:
Paper roll:
Cash drawer:
Accessories:
ER-A450S
355 (W) x 424 (D) x 308 (H) mm
12.9 kg
Official (nominal) voltage and frequency
Stand-by 14W
Operating 41W (max.)
0 °C to 40 °C
LSI (CPU) etc.
Rechargeable battery, memory holding time about 1 month
(with fully charged built-in battery, at room temperature)
7-segment display (10 positions)
7-segment display (7 positions)
2-station thermal printer
Approx. 13.3 lines/second
24 digits each for receipt and journal paper
• Graphic logo printing function
• Logo message function
• Receipt (ON-OFF) function, journal selective function
• Receipt and journal independent paper feed function
Width: 44.5 ± 0.5 mm
Max. diam.: 80 mm
Quality: High quality (0.06 to 0.08 mm thickness)
5 slots for bill and 8 for coin denominations
Manager key
2
Submanager key
2
Operator key
2
Drawer lock key
2
Paper roll
2
Take-up spool
1
Fixing angle bracket
1
Instruction manual
1 copy
* Specifications and appearance subject to change without notice for improvement.
160
FOR CUSTOMERS IN U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
BLUE:
BROWN:
Neutral
Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter
N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured red.
The apparatus must be protected by a 3A fuse in the mains plug or distribution board.
CAUTION: DO NOT CONNECT THE LIVE (BROWN) WIRE OR THE NEUTRAL (BLUE) WIRE
TO THE EARTH TERMINAL OF YOUR 3-PIN MAINS PLUG.
Environment Protection
The device is supported by a battery. To dispose the battery safely to protect the environment,
please note the following points:
• Take the used battery to your local waste depot, dealer or customer service centre for recycling.
• Do not throw the used battery into fire, into water or into the household waste!
Umweltschutz
Das Gerät wird durch eine Batterie gestützt. Um die Batterie sicher und umweltschonend zu
entsorgen, beachten Sie bitte folgende Punkte:
• Bringen Sie die leere Batterie zu Ihrer örtlichen Mülldeponie, zum Händler oder zum
Kundenservice-Zentrum zur Entsorgung.
• Werfen Sie die leere Batterie niemals ins Feuer, ins Wasser oder in den Hausmüll.
Protection de l’environnement
L’appareil est supporté sur pile. Afin de protéger l’environnement, nous vous recommendons de
traiter la pile usagée la façon suivante:
• Apporter la pile usagée à votre centre de traitement des ordures ménagères le plus proche ou,
à votre revendeur ou, au service après-vente, pour recyclement.
• Ne jamais jeter la pile usagée dans une source de chaleur, dans l’eau ou dans les vide-ordures.
Miijöskydd
Denna produkt nöddrivs av batteri.
Vid batteribyte skall följande iakttagas:
• Det förbrukade batteriet skall inlämnas till er lokala handlare eller till kommunal miljöstation för
återinssamling.
• Kasta ej batteriet i vattnet eller i hushållssoporna. Batteriet får ej heller utsätttas för öppen eld.
SHARP CORPORATION
Printed in Korea / Imprimé en Corée / Gedruckt in Korea / Impreso en Corea
T(TINSE2433BHZZ)➀
">