JEM ZR44 Hi-Mass User Manual

JEM ZR44 Hi-Mass User Manual
P/N 35010032-D
TM
ZR44 HI-MASS
user manual
Dimensions
All dimensions are in millimeters
© 2016 Martin Professional™ ApS. Information subject to change without notice. Martin
Professional™ and all affiliated companies disclaim liability for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss occasioned by the use of,
inability to use or reliance on the information contained in this manual. Martin™, Harman™
and all other trademarks in this document pertaining to services or products by Martin
Professional™ or its affiliates and subsidiaries are registered as the property of Harman
International Industries.
2
Dimensions
Contents
Dimensions ................................................................................................................................ 2
Contents .................................................................................................................................... 3
Safety information ...................................................................................................................... 4
Product overview ....................................................................................................................... 7
Product description ................................................................................................................ 7
Features at a glance .............................................................................................................. 7
Product details ....................................................................................................................... 8
Quick Start ................................................................................................................................. 9
Setting up ............................................................................................................................... 9
Making fog ............................................................................................................................. 9
Installation and setting up ....................................................................................................... 10
Location ............................................................................................................................... 10
AC power ............................................................................................................................. 10
Setting up ............................................................................................................................. 11
Final checks ......................................................................................................................... 11
Turning on the power ........................................................................................................... 11
Control settings ....................................................................................................................... 12
Overview .............................................................................................................................. 12
Manual firing ........................................................................................................................ 12
Setting fog output level ........................................................................................................ 12
Setting the Timer .................................................................................................................. 12
Setting the master-slave link mode...................................................................................... 12
Digital remote control .............................................................................................................. 13
Overview .............................................................................................................................. 13
Functions ............................................................................................................................. 13
DMX control ............................................................................................................................. 14
Overview .............................................................................................................................. 14
Connection ........................................................................................................................... 14
DMX functions ...................................................................................................................... 14
Setting the DMX address ..................................................................................................... 15
Approved fluid types ................................................................................................................ 16
Pro Clean Supreme Fluid ..................................................................................................... 17
Basic service ............................................................................................................................ 18
Cleaning ............................................................................................................................... 18
Fuse replacement ................................................................................................................ 18
Troubleshooting ...................................................................................................................... 19
Resetting the machine after fluid out ................................................................................... 19
Technical Specifications .......................................................................................................... 20
Notes ....................................................................................................................................... 24
Contents
3
Safety information
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
personal injury.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due to
electric shock, burns, falls and respiratory problems!
Read this manual before operating the machine, follow the safety precautions
listed below, and observe all warnings in this manual and printed on the
machine. Use the system only as described in this manual and in accordance
with local laws and regulations.
If you have questions about how to operate the machine safely, or if you have
followed the instructions in this manual and the machine is malfunctioning,
please contact Martin Service.
P r e ve n t i n g e l e ct ri c s h o c k s
4

Always ground (earth) the machine electrically.

Use only a source of AC power that complies with local building and
electrical codes, and that has both overload and ground-fault protection.

Before connecting the fog machine to power, check that the voltage
indicated on the machine’s serial label matches your local AC power
voltage. If your AC power voltage does not match, do not use the
machine. Contact Martin Service for assistance.

Before using the machine, check that all power distribution equipment
and cables are in perfect condition and rated for the current
requirements of all connected devices.

If the machine or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the machine
and contact Martin Service for assistance. If the supply cord is
damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent.

Disconnect the machine from AC power before servicing and when not
in use.

This system is not waterproof and should not be exposed to wet
outdoor conditions. Do not immerse in water or any other liquid. Do not
expose to high-pressure water jets.

Do not spill fluid over or inside the machine. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the system out of service and contact Martin for advice.
Safety information

Do not remove the covers or attempt to repair a faulty machine. Refer
any service not described in this manual to Martin.

Do not operate the machine if any parts are damaged, defective or
missing.

Moisture and electricity do not mix. Do not aim fog output at electrical
connections or devices.
P r e ve n t i n g b u r n s an d f i r e

The fog produced by the machine is hot enough to cause burns when it
leaves the nozzle, and very hot droplets of fluid escape occasionally.
Keep people and objects at least 1 meter (39 inches) away from the fog
output nozzle.

Do not touch the fog output nozzle during or after use – it becomes
extremely hot and remains hot for several hours after the machine has
been shut down.

Fog output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point fog output at sources of ignition
such as open flames or pyrotechnic effects.

Do not attempt to bypass thermostatic switches, fluid sensors or fuses.

Replace fuses only with ones of the type and rating specified in this
manual for the machine.

Provide a minimum free space of 100 mm (4 in.) around the machine.

Provide a minimum free space of 500 mm (20 in.) around fans and air
vents and ensure free and unobstructed air flow to and around the
machine.

Keep the machine at least 600 mm (24 in.) away from combustible and
heat-sensitive materials.

Do not operate the machine if the ambient temperature (Ta) is below 5°
C (41° F) or above 40° C (104° F).

Do not operate the machine if the relative air humidity exceeds 80%.
P r e ve n t i n g i n j u ri e s

Ensure that the surface on which the machine is located or installed can
safely hold the weight of the machine.

Do not install the machine over areas where people are present.

This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.

Fog machines can cause condensation. Do not point the output at
smooth floors. Floors and surfaces may become slippery. Check these
frequently and wipe dry as necessary to avoid any danger of slipping.

Ensure at least 2 m (6.6 ft.) visibility in areas where fog is being
produced.

Fog fluid contains food-grade glycols in solution but may present health
risks if swallowed. Do not drink it. Store it securely. If eye contact
occurs, rinse with water. If fluid is swallowed, give water and obtain
medical advice.
Safety information
5
P r e ve n t i n g b r e at h i n g p r o b l em s
6

A fog machine can operate safely only with the fog fluid it is designed
for. Use the machine only with fluids specified under “Approved fluid
types” on page 16 or you may cause the release of toxic gases,
presenting a severe health hazard. You will also probably damage the
machine.

Do not create dense fog in confined or poorly ventilated areas.

Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to fog output.

Do not point fog output directly at a person’s face or at face height.
Safety information
Product overview
Product description
The JEM ZR44 Hi-Mass™ is a reliable and highly efficient fogger capable of
precise fog delivery from subtle to massive. Ideal for a variety of settings from
small venues to huge stadiums and arenas, it features advanced technology for
top-quality performance, as well as advances in digital functionality such as
RDM compatibility.
Following on from its predecessor the industry standard JEM ZR33™ the new
JEM ZR44 Hi-Mass™ encompasses what Martin fog effect machines are all
about: state of the art technology, high quality and ruggedness.
Congratulations on your purchase of this fog machine from Martin. Details of the
full range of Martin products are available on our website at www.martin.com.
Features at a glance

Robust road-worthy design

Integrated analog remote control

DMX with RDM standard

Hanging bracket included

Continuous microprocessor controlled effect output

Different fluid options for different applications

1800 W Heat exchanger

Soft start technology

Fluid sensing system

Optional drip tray, digital remote control and ducting kit
Product overview
7
Product details
Remove remote control to access
Digital remote (accessory) socket.
Remote control
Main power
switch
Power inlet
connector
Dip switch
(DMX address)
5 pin DMX
input and
link
AVR program
upload socket
3 pin DMX
input and
link
If suspending overhead:
Wrap safety cable under
hanging bracket and
secure.
Fluid Reservoir
Fog output nozzle
Hanging bracket
8
Warning, high
temperature vapor and
surfaces!
Product overview
Quick Start
You are no doubt eager to switch on the machine and try it out by making a lot
of fog. This section tells you how to do that. However, please also make the time
to read the safety and servicing instructions in the remainder of this manual.
Setting up
Locate the machine in a suitably large area with nothing in front of the fog
output.
Fill the fluid tank with Martin approved fluid (see page 16).
Connect the machine to a suitably rated power source. The power requirements
are:
EU Models - 1890 W, 220-240 V
US Models – 1890 W, 100-130 V
Now set the mains switch, at the rear of the machine, to the ‘ON’ position and
press the grey “stand-by” button.
The ‘Ready’ LED will flash indicating the machine is heating up; allow around
10 minutes for the machine to reach operating temperature. Once the machine
has heated the ‘Ready’ LED will stop flashing and be permanently on.
Making fog
Once the machine has heated up, hold the FOG button on the remote to start
the fog output.
It may be necessary to prime the machine, to do this simply hold down the FOG
button and turn the output knob to maximum. Keep the button held until the fog
output is strong and steady. Then turn the knob back to the required output
level and release the FOG button.
You can set the fog density by turning the knob. If the knob is turned fully
counter-clockwise, no fog will be produced.
Quick Start
9
Installation and setting up
DANGER! DO NOT operate the fog machine until you have read and observed
all the precautions listed under “Safety information” on page 4.
Location
The fog machine may be located on the floor or may be suspended using the
hanging bracket. If suspending the machine, a standard hanging clamp
(available from Martin) should be attached to the machines hanging bracket with
an M12 bolt and nyloc nut. Additionally, a secondary backup device, a safety cable
(available from Martin) should be looped around the hanging bracket.
The machine can operate in any orientation from 45 degrees upwards to 45
degrees downwards. Steeper tilting may cause fluid leakage.
If the machine is to be suspended, ensure the mounting surface can support the
weight of the machine. Do not suspend the machine over areas where people
will be underneath.
Ensure that there is at least 100 mm (4 in.) clearance around the machine and at
least 600 mm (24 in.) in front of the fog output.
AC power
Before using the machine, ensure that a grounding-type (earthed) power plug
that fits the local power outlets is installed on the power cable.
DANGER! Make sure the power plug is correctly rated:
• For EU models use a plug rated at 10 A minimum
• For US models use a plug rated at 20 A minimum
When installing the plug, follow the plug manufacturer’s instructions and
connect pins as follows:
Yellow and green wire to ground (earth), blue wire to neutral and brown wire to
live.
The table below shows some common pin identification schemes.
wire
function
marking
screw colour
brown
live
“L”
yellow or brass
blue
neutral
“N”
silver
green/yellow
earth
green
Before connecting the fog machine to power, verify that the AC supply is
adequately dimensioned for the current draw of the machine. The machine
requires:
EU Models - 1890 W, 220-240 V
US Models – 1890 W, 100-130 V
10
Installation and setting up
Check that the local AC voltage is appropriate, as indicated on the machine’s
serial number label. If your AC voltage is outside the appropriate range, do not
use the machine. Contact Martin Service for assistance.
Setting up
Fill the fluid tank with Martin approved fog fluid (see page 16).
If DMX control is being used, connect the machine to the DMX line (see page
14).
Final checks
Before applying power to the fog machine, verify the following:
 the machine is safely located or installed and meets the location
requirements stated on page 10

the operator is familiar with, and able to comply with, the requirements
for safe operation listed on page 4

the fog fluid is one of the genuine Martin fluids listed under “Approved
fluid types” on page 16

the machine is electrically grounded (earthed)

the AC power distribution circuits and lines are adequately rated for the
current load
Turning on the power
Turn on the main power switch located next to the power cable inlet.
The green ‘Ready’ indicator on the rear of the machine will flash for about 10
minutes as the machine heats up to operating temperature.
When the green Ready indicator stops flashing and is permanently on, the
machine is ready to make fog.
Installation and setting up
11
Control settings
Overview
The unit is controlled using the remote control. You can control it in these ways:

Manual firing by holding down the FOG button

Automatic fog bursts using a repeating timer
Manual firing
Hold down the FOG button. The machine will produce fog until you release the
button.
If a long burst of fog is produced, after a time the fog output level will be
automatically reduced to keep the machine temperature within the operating
range. This allows continuous operation, so that the machine does not have to
stop and re-heat.
Setting fog output level
Set the knob to the desired output level while firing the machine. The fog output
level is always set by the current position of the knob, whether manually firing or
in timer mode.
Setting the Timer
FOG BUTTON: Will when the machine has reached operating temperature fire
the machine when pressed and held.
STAND-BY BUTTON: This turns the machines electronics on and off.
TIMER VALUE BUTTON: When the timer is being used, the timer values can be
adjusted by a factor of 8, i.e. a 5 second minimum run time becomes 40
seconds & a 10 second delay time becomes 1 minute 20 seconds.
TIMER ENGAGE: This will engage the timer to fire the machine according to the
present settings.
OUTPUT CONTROL: Turning this knob clockwise will increase the output of the
machine, if turned fully anti-clockwise there will be no output.
DELAY TIME CONTROL: This will adjust the amount of time the machine waits
between operating when the timer is engaged.
RUN TIME CONTROL: This will adjust the time the machine will operate for
when the timer is engaged.
POWER LED: This LED will light when the machine is switched on
CYCLE LED: This LED will light when the timer is engaged and the machine is
operating.
Setting the master-slave link mode
It is possible to control several machines from either the onboard remote control
or the optional accessory digital remote. The machines are interconnected with
DMX cabling via either the 3 or 5-pin XLR sockets situated on the rear of the
machine
Dip switch 11 located on the rear of the machine must be set to the down
position on the master unit.
12
Control settings
Digital remote control
Overview
A Digital Remote control, available separately, may be used for control of the
JEM ZR44 HI-MASS™
Display
XLR socket
XLR socket
(on rear)
Timer button
Fog button
Functions
The remote control provides the following functions:

Fog button: turns fog output on and off. Press once to start fog and
again to stop.

Timer button: turns the fog timer on and off.

Fog level setting (Fog = 0 -100%)

Timer run time/off time settings (,  = 0 - 90 seconds)

Run mode (RUN = , , , )
The Fog button works by setting RUN to  (or ). The Timer button
sets RUN to  or . These buttons are simply a quick way to
control this menu function.
Digital remote control
13
DMX control
Overview
DMX is a digital control system widely used in entertainment and architectural
lighting. Any controller meeting the DMX-512 standard may be used to control
and program the fog output of the fog machine.
Connection
The fog machine provides both 3 & 5-pin XLR plug and socket on the rear panel
for DMX connection. The wiring is shown below.
Connector pin
function
1
Ground
2
Data – (“Cold”)
3
Data + (“Hot”)
For best results, use cable designed for high speed digital data transmission.
DMX functions
The fog machine operates from a single DMX channel which gives proportional
control of fog density from 0-100%.
DMX Level
function
0 – 12
No fog
13 – 255
Fog at variable density, (13=minimum, 255=maximum)
When the machine is receiving valid DMX data, the indicator light next to the
address switches will light.
14
DMX control
Setting the DMX address
Each unit on a DMX system must be allocated an address so that the DMX
controller can send separate commands to the unit. On the fog machine, the
DMX address is set using the bank of switches (“dip switches”) on the back
panel next to the DMX connectors. The switch settings for each possible DMX
address are given in the table below.
DIP-Switch Setting
0 = OFF
1 = ON
#1
#2
#3
#4
#5
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
#9
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
#8
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
#7
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
#6
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
DMX control
15
Approved fluid types
The following types of Martin fog fluid are approved for use in this machine.
Each produces a different effect as described below. Martin supplies high
quality fog fluids that are based on ultra-pure deionized water. Use only the
following genuine Martin fog fluids. No other fluid is suitable for use.
P r o S m o k e S u p e r ( Z R m i x)
Pro Smoke Super fluid is a high-quality, general purpose fluid that produces a
dense white airborne fog with medium dispersal time. Its medium to high index
of refraction permits both good atmospheric effects and denser “white-outs”.
P r o S m o k e H i g h D en s i t y ( S P m i x)
Pro Smoke High Density fluid generates a high density, white, airborne fog with
a very high index of refraction and slow evaporation rate. It is well suited for
scenic obscuring, dramatic strobe effects, and “white-outs”.
P r o S m o k e S t u d i o ( D X mi x )
In a studio or theater environment, a lighter, faster dispersing fog is often
preferred. Pro-Smoke Studio offers a less dense environment to Pro-Smoke
Super and is therefore less likely to interfere with TV camera focusing.
i-fog
i-fog is not only kind to your lights, but is also more economical to use thanks to
its incredible long “hang time” characteristics. In environments unaffected by
extraction and air-conditioning, i-fog can be expected to last
P r o S t e am S i m u l at i o n
Steam simulation fluid specifically designed for ‘steam’ effects. Creates a white
burst, but is fast dispersing.
(In order to optimise the machines temperature setting the dip switch on the
rear marked ‘Low Temp’ should be set down to position 1).
RUSH Fog Fluid™
RUSH Fog Fluid™ is a specially formulated water-based fog formula and is
recommended for use with applicable Martin fog effect generators. While
economical it is perfect for medium-density airborne fog effects with medium
hang time and leaves no residue; RUSH Fog Fluid™ is designed as an economy
fluid that is suitable for use in nightclubs, bars, stage and outdoor events.
*Please note that use of RUSH Fog Fluid™ in a JEM™ series fog machine will produce a
less than expected professional quality effect due to the nature of using an entry level fog
effect fluid.
DANGER! The fog machine can run safely only on the specific fog fluids it
is designed for. Use ONLY the Martin fog fluids designated in this manual.
NEVER use any other type of fluid, or toxic gas may be produced. You will
probably also cause damage to the system that is not covered by the
product warranty. Do not dilute fog fluid with water or any other liquid.
Discard fog fluid if it becomes contaminated.
16
Approved fluid types
Pro Clean Supreme Fluid
Specially designed for optimum performance while providing longevity of the
heat exchanger, Pro Clean Supreme is the ultimate cleaning solution for Martin
fog and haze effect machines. Applying Pro Clean Supreme fluid on a regular
basis reduces clogging and further extends the life of Martin fog and haze
machines.
Using Pro Clean Supreme every 200 hours, or once a month (depending on
usage), will prolong the life of the heat exchanger in Martin fog and haze
machines. Connect Pro Clean Supreme fluid to the fogger or hazer, then allow
the unit to heat. When fully ready, activate the machine or remote for
approximately 30-45 minutes (use the timer function if available). When
completed, replace cleaning fluid with appropriate fluid.
Note: Cleaning procedure should be used if the unit is to be stored for 30 days
or more. Ensure there is no fluid in the fluid tube when placing in storage.
Approved fluid types
17
Basic service
Before servicing the fog machine, read and observe all the precautions listed in
“Safety information” on page 4. Any service not described in this section must be
carried out by a Martin service technician.
Cleaning
Excessive dust, fog fluid, and dirt build-up will degrade performance and cause
overheating and damage to the machine that is not covered by the product
warranty. To maintain adequate cooling, dust must be cleaned from the outer
casing and air vents of the machine periodically.
Isolate the machine from power and allow to cool completely before cleaning.
The fog output nozzle remains hot for up to 10 hours after use.

Remove dust from the air vents with a soft brush, cotton swab, vacuum,
or compressed air.

Clean fog fluid residues from the fog output of the machine using a
damp cloth.

Clean the outer casing with a damp cloth only.
Fuse replacement
The main fuse for the fog machine is located on the electronics board inside the
unit.
DANGER! Disconnect the power supply before removing any covers. Live parts
inside!
To replace the fuse, disconnect the power cord from the supply, unscrew the
screws holding the rear cover of the unit and remove the cover. The electronics
board is located at the back of the unit.
Remove the spent fuse and replace with one of exactly the same size and rating.
The fuse type is indicated below. Contact Martin Service if the fuse blows
repeatedly.
US Model = 20AT (slow-blow), 125 V
EU Model = 10AT (slow-blow), 250 V
18
Basic service
Troubleshooting
Problem
Probable cause(s)
Suggested remedy
Machine not at operating
temperature
Wait 10 to 15 minutes
Machine not powered up or
heaters disabled
Ensure mains power switch
on, enable heaters by
pressing FOG
Output level control set to
zero
Increase setting
Timer is engaged
Disengage the timer by
pressing the FOG/TIMER
ENGAGE button briefly
DMX address setting
incorrect
Change DMX address (page
15)
Poor connection in DMX line
Check DMX cables and
connections
Fog output is weak
Machine requires priming
Prime machine (page 10)
Wet, greasy, non-uniform
fog output, fluid drips or
spits from nozzles, or very
loud noise when firing
machine
Incompatible fog fluid
Use only approved fluids!
Mains fuse blown
Replace fuse (page 19)
No power at AC cable inlet
Check power cable and
circuit breaker
Machine will not produce fog
when remote control Fog
button pressed
Machine continues to
produce fog when Fog
button is not pressed
Machine can be fired from
the remote control, but not
by DMX controller
Machine appears dead
Resetting the machine after fluid out
If the machine runs out of fluid it will automatically shut down to prevent any
damage occurring, the Low Fluid LED on the rear will illuminate. To reset simply
turn the mains power off and back on again. Refill the fluid container and follow
the priming instructions under ‘Making fog’ on page 10.
Troubleshooting
19
Technical Specifications
P h ys i c a l
Length ......................................................................................... 687 mm (27.1 in.)
Length with optional drip tray ........................................................ 752 mm (30 in.)
Width .............................................................................................. 379 mm (15 in.)
Height ............................................................................................ 248 mm (9.8 in.)
Height with hanging bracket ....................................................... 353 mm (13.9 in.)
Weight, dry ...................................................................................... 19 kg (41.9 lb.)
Weight, filled ................................................................................. 28.5 kg (62.9 lb.)
Performance
Coverage volume ................................................... 1200m3 (42,378 ft3) per minute
Fluid consumption (max) ................................................................. 120 ml/minute
Continuous effect output
Ready time ............................................................................................ 10 minutes
C o n t r o l a n d P r o gr am mi n g
Control options ....................................... Integrated analog remote control, DMX,
........................................ optional digital remote control, master/slave link mode
Control parameters ................................... Continuous or timer-controlled output
Fog ...................................................................... Variable output control, 0-100%
DMX channels ...................................................................................................... 1
DMX compliance ........................................................................ USITT DMX512-A
RDM compliance ...............................................................ANSI/ESTA E1.20 RDM
Construction
Color ..................................................................................................... Black, silver
Housing .................................................................................. Steel and aluminium
Fluid reservoir ...................................................................................... 9.5 l drop-in
Heat exchanger ..........................................................1800 W, thermally protected
Fluid pump .......................................................... Oscillating piston, high pressure
Fluid management ............................ Fluid out sensing, sealed for transportation
External fluid control ......................................................................... Fluid sensing
Drip tray .............................. Optional bolt-on tray with reusable collection sponge
I n s t al l at i o n
Mounting ................................................................................ Standing or hanging
Orientation .................................................................Up to +/- 45° from horizontal
Clearance around machine.............................................................. 100 mm (4 in.)
Connections
AC power ..................................................................................Neutrik PowerCon
DMX, link mode in/out ..................................................... 3- and 5-pin locking XLR
Remote control ............................................................................ 3-pin locking XLR
Firmware .............................................................................................. AVR Socket
E l e c t ri c a l
AC power (EU) ......................................................................... 220-240V, 50/60Hz
AC power (US) ......................................................................... 100-130V, 50/60Hz
Main fuse (EU) ................................................................ 10AT (slow-blow), 250 V
Main fuse (US) ................................................................ 20AT (slow-blow), 125 V
Typical power and current (EU) ..................................................... 1890 W, 8.3 A*
Typical power and current (US) ................................................... 1890 W, 14.6 A*
20
Technical Specifications
*Measurements made at nominal voltage. Allow for a deviation of +/- 10%
Th e r m a l
Exterior surface temperature, steady state ........................................ 50° C (122 °F)
Maximum ambient temperature (Ta max) .......................................... 40° C (104° F)
Maximum nozzle temperature.......................................................... 200° C (392° F)
Minimum ambient temperature (Ta min) ............................................... 5° C (41 °F)
Ap p r o va l s
EU Model
EU safety: ................................................................. EN 60 335-1+A15, EN 62233
EU EMC:..............................................................................................EN 61000-6-3
EU immunity: .......................................................................................EN 61000-6-1
Australia/NZ (pending): .....................................................................................RCM
US Model
US Safety ...................................................................................................... UL 998
Canadian Safety ................................................................... CSA C22.2 No. 104.01
Included Items
Analog remote control ....................................................................... P/N 92765038
Fluid reservoir, 9.5 l ............................................................................ P/N 34300528
Power input cable, EU, Neutrik PowerCON, stripped ends, 2.5 m (8.2 ft.)
........................................................................................................... P/N 11501041
Power input cable, US, Neutrik PowerCON, molded NEMA 5-15P, 2.5 m (8.2 ft.)
........................................................................................................... P/N 11501042
User manual ....................................................................................... P/N 35010032
Ac c e s s o r i e s
JEM™ ZR44 Digital Remote Control .................................................. P/N 92765037
JEM™ ZR44 Ducting Kit with 5 m (16.4 ft.) ducting ........................... P/N 92625005
JEM™ ZR44 Drip Tray ........................................................................ P/N 92620011
Approved Fluids
JEM™ Pro Smoke Studio
JEM™ Pro Smoke Super
JEM™ Pro Smoke High Density
JEM™ i-fog Fluid
JEM™ Pro Steam Simulation Fluid
JEM™ Pro Clean Supreme Fluid
*Various sizes available - contact your dealer or see martin.com for more details.
Installation Hardware
Half-coupler clamp ............................................................................. P/N 91602005
G-clamp (vertical hanging suspension only) ..................................... P/N 91602003
Quick trigger clamp (vertical hanging suspension only) ................... P/N 91602007
Service Tools
Epsilon 5 AVR Programmer ............................................................... P/N 50502004
Temperature Calibration Box ............................................................. P/N 92620005
O r d e ri n g i n f or m at i o n
JEM™ ZR44 Hi-Mass™, EU ................................................................ P/N 92215300
JEM™ ZR44 Hi-Mass™, US ................................................................ P/N 92215310
Technical Specifications
21
Specifications subject to change without notice. For the latest technical
specifications, see www.martin.com
22
Technical Specifications
23
Notes
24
Notes
25
Disposing of this product
Martin™ products are supplied in compliance with Directive 2002/96/EC of the European
Parliament and of the Council of the European Union on WEEE (Waste Electrical and
Electronic Equipment), as amended by Directive 2003/108/EC, where applicable.
Help preserve the environment! Ensure that this product is recycled at the end of its life.
Your supplier can give details of local arrangements for the disposal of Martin products.
26
27
Martin Professional A/S,Olof Palmes Allé 18, DK-8200,Aarhus N
Phone: +45 87 40 00 00 Internet: www.martin.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement