IM-TLK-CSN
INSTRUCTIONS
Your Analog Talking Watch is a Single
Band Radio Controlled watch. The
National Institute of Standards and
Technology (NIST) radio station, WWVB,
located in Ft. Collins, Colorado,
continuously broadcasts the time signal at
60 Khz. This signal can be received up
to 2,000 miles away, anywhere in the
continental USA where long wave (AM)
radio reception is possible, The WWVB
station derives its signal from the NIST
Atomic Clock in Boulder, CO . Your Atomic
Watch automatically adjusts for daylight
saving time.
BEFORE FIRST TIME USE SET YOUR
TIME ZONE!
Please wait whenever the clock hands are
automatically spinning. The watch is
setting the correct time. Your watch will
resume running with the correct time
automatically when the second hand stops
1
spinning fast. You will not be able to use
any other function while the watch is
setting itself.
10 o’clock button га 2 o'clock button
8 o'clock button & @ 4 o'clock button
Time Zone Setting:
To receive the correct time you first
need to set your Time Zone:
1. Hold 8 o'clock button for more than 5
seconds until the watch says "Set
Alarm, Press 10 o,clock button to set”
2. Push 8 o'clock button another 3 times in
a row, until the watch says “ Time
Zone Setting. Press 10 o,clock button to
set”
3. Press 10 o'clock button
4. After pressing 10 o'clock button, it says
“Press 2 o'clock button to set, 8 o'clock
button to confirm”
Press 2 o'clock button repeatedly until
you reach correct time zone then stop:
USA, Pacific
USA, Mountain
USA, Central
USA, Eastern
5. Press 8 o'clock button to confirm after
making your selection
6. After confirmation, the watch hands
will spin automatically until they reach
the local time of the selected time zone.
7. When switching between “Daylight
Saving Time” and “Standard Time the
time will be corrected after signal
reception has been updated overnight.
8. The watch will synchronize with the
USA atomic clock automatically every
night.
Talking Functions:
Time:
Push 2 o'clock button to hear the Hour and
Minute.
Date.
Push 4 o'clock button to hear the Day,
Month, Date and Year
Note: There is no Date Talking function
after a new battery is installed until it gets
a first signal reception.
Reception Status Check:
1. Push 8 o'clock button once while the
watch is running normally.
3
2. If the reception was successful, the
watch will say "USA Time Updated”
3. If the reception failed, the watch will say
"USA Time Not Updated”
Alarm Time:
1. Push 10 o'clock button once and you
will hear if Alarm Time has been set
2. If the Alarm is turned Off, the watch will
say “Alarm is Off”
3. If the Alarm is turned On, the watch will
say The Alarm time is“ (followed by the
alarm time)
Alarm Settings:
Set Daily Alarm Time:
Hold 8 o'clock button while the watch is
in real time mode for more than 5
seconds until the watch says "Set
Alarm, Press 10 o'clock button to set.”
. Press 10 o'clock button.
. The watch says, "Press 2 o'clock button
to set Hour, 4 o'clock button for
Minutes, 8 o'clock to confirm.”
4, Press 2 o'clock button repeatedly to set
Hour. Next press 4 o'clock button
repeatedly for Minute.
5. Press 8 o'clock button to confirm after
vou have set the Alarm time.
4
LJ Ml
6. After confirmation, the watch will say
the Alarm time that you have set.
7. You can also check your Alarm time
with a push of the 10 oclock button
any time you want.
8. The Alarm will Beep for 30 seconds;
vou can turn off the alarm with the
push of any button.
9. The Alarm is a Daily alarm, so even
after you turn off the Beeping Sound,
the alarm will Beep again the next day.
If you want to permanently turn off the
Daily Alarm, you can follow the Alarm
Off setting below.
10.Every time the Alarm goes off, the
watch will say the Alarm Time.
Alarm ON/OFF:
1. Hold 8 o'clock button while the watch is
in the real time mode for more than 5
seconds until the watch says "Set Alarm,
Press 10 o'clock to set.”
2.Push 8 o'clock button one more time,
the watch says "Alarm ON/OFF, Press
10 o'clock button to set.”
. Press 10 o'clock button.
. The watch says, "Press 2 o'clock button
to ON, 4 o'clock button to OFF, 8 o'clock
button to confirm.”
Fa LU
``] Ch
. To turn ON the daily alarm, Press 2
o'clock button. To turn OFF the daily
alarm, Press 4 o'clock button.
. Press 8 o'clock button to confirm.
. If Alarm is OFF, the watch says, Alarm
is OFF" when 10 o'clock button is
pushed.
. If Alarm is ON the watch says, "The
alarm time is” followed by the alarm
time when 10 o'clock button is pushed.
Hourly Chime Settings:
Hourly Announcemer ime
ON/OFF
(When Chime is ON, the watch announces
the HOUR every Hour)
Ls
Ju LU
Hold 8 o'clock button while the watch is
in the real time mode for more than 5
seconds until the watch says "Set
Alarm, Press 10 o'clock button to set.”
. Push 8 o'clock button 2 more times,
until the watch says "Chime ON/OFF,
Press 10 o'clock button to set”
. Press 10 o'clock button.
. The watch says, "Press 2 o'clock button
to ON, 4 o'clock button to OFF, 8 o'clock
button to confirm.”
5. To turn OFF a Chime Alert, Press 4
o'clock button.To turn ON a Chime
Alert, Press 2 o'clock button.
. Press 8 o'clock button to confirm.
. After a Chime alert is turned ON, the
watch will announce the HOUR every
one hour.
= Oh
Manual Signal Reception:
Set the correct Time Zone before initiating
Manual Signal Reception. Go to "Time
Zone Setting” section for details. Follow
below if you want your watch to search for
signal immediately and not wait overnight.
While the watch is in normal running
mode:
1. Press and Hold the 10 o'clock button
until the second hand stops at the 7
o'clock position.
2. The watch takes about 5 to 15 minutes
to pick up the radio signal. Wait until
the watch has finished the signal
receiving procedure.
3. After successful signal reception, the
watch will show the correct time after
the fast running second-hand stops.
4. Push 8 o'clock button once. The watch
will say the status of the reception.
5. If reception was successful, the watch
will say "USA Time Updated.”
7
IM-TLK-C5N-04
6. If reception failed, the watch will
say "USA Time Not Updated.”
7. You may move watch to another location
where reception may be more favorable
and try manual reception again or wait
overnight for better possible reception.
Manual Time Setting:
You should use this function if traveling to
countries with no signal reception. You
must also set correct time of day (AM/PM)
and time zone when you come back from
travel to other countries.
|
= LW
Hold 8 o'clock button for more than 5
seconds until the watch says "Set
Alarm, Press 10 o'clock button to set”
Push 8 o'clock button 4 more times,
until the watch says, "Set time. Press
10 o'clock button to set”
. Press 10 o'clock button
. The watch says, Press 2 o clock button
to set Hour, 4 o'clock button for
minutes, 8 o'clock button to confirm”
. Press 2 o'clock button to set Hour.
Listen very carefully to the watch to
make sure the right AM or PM has been
set (if you set the wrong AM/PM your
8
watch will not be able to pick up signal
at 3:00AM).
6. Press 4 o'clock button to set Minute.
7. Press 8 o'clock button to confirm after
you have set the Time.
8. After confirmation, the watch will
automatically run to the time you have
set. Wait until the watch stops running
fast.
Your watch is not able to manually
set Day, Month and Year. The watch
provides this information only when
a first signal reception is received.
Best Overnight Signal Reception
Method:
Your watch should be positioned in the
following manner and placed near a
window during signal reception in order to
get the best possible result.
Metal i or PU fn Watch.
e Place the watch case flat or face down
on a wooden table during signal
reception
—— ae”
|
| NOODENTARRE | X WOODEN TABLE “Uy
METAL OR PU BAND LEATHER BAND
Incorrect Position for Signal Reception:
e Don't let the metal watchband touch the
case back as it may affect signal
reception.(Insert a piece of cardboard
between the case back and the metal
band to keep them separated).
e Never put the metal band , leather
band or pu band watch on it’s side because
it may not be able to pick up the signal
well. X X
Never Jet Ihe metal band auch Ihe case back. Never ры! Ше walch on 11% side as it will
ав И will effect signal réception rot be able to gel signal in this positian
Troubleshooting:
Your watch is a very delicate and precise
instrument. Although uncommon,
sometimes hard knocks or vibrations can
cause the hands to move irregularly, and
therefore display the incorrect time,
10
although the internal clock is keeping
accurate time. If when doing a "manual
signal reception” (press and hold the 10
o'clock button until the second hand stops)
the second-hand does not pause exactly at
the 7 o'clock reference point (half second
deviation is acceptable), then the second-
hand needs to be re-calibrated.
Re-calibrate the shifted second-hand:
1. Make sure the watch is running
normally.
2. Hold 8 o'clock button for more than 5
seconds until the watch says "Set
Alarm, Press 10 o'clock button to set.”
3. Push 8 o'clock button 5 more times
until the watch says “ Second-Hand
Alignment, Press 10 o'clock button to
set.”
4. Press 10 o'clock button. Watch says,
“Press 2 o'clock button to set, 8 o'clock
button to confirm.”
5. Keep an eye on the second-hand as it
moves to a new position and stops
somewhere before 6 o'clock position
then immediately Press 2 o'clock
button repeatedly until the second-
hand points exactly down at 6 o,clock
position. Press 8 o'clock button to
confirm. (The watch will stop for a
11
while. Just wait until the watch
resumes normal running).
6. If the second hand stops advancing
before it reaches 6 o'clock position
repeat steps 2 through 5 above until
the second had points to exactly 6
o'clock.
7. The second-hand is re-calibrated.
Watch Not Receiving Time Signal:
Reasons for not being able to receive the
Time Signal include:
-Being outside of the country
-Being in a built up area
-Metal objects blocking the radio signal
-Interference from computer monitor or TV
Ensure that the watch is set by a window,
as this provides the best reception, you
may have to try different windows in the
house to see which is best. Please note
that reception is always better at night. If
your watch is unable to receive the radio
signal, it will continue to function in the
same way as a standard watch. The time
will then be corrected the next time your
watch receives the time signal.
B E
When the battery is low, the watch hands
automatically advance to 12 o'clock and
12
stop. The talking function also terminates.
The battery needs to be replaced. Go to
"Battery Replacement” section for details.
NOTE: If the watch hands DO NOT
stop at 12 o'clock before battery
replacement you need to reset the hands
to 12 o'clock manually immediately after a
new battery is installed. Go to Reset
Procedure / Set the Hands to 12 o'clock
Manually” section for details.
Battery Replacement:
This watch uses a CR2032 type battery;
trained jewellers or watch specialists
should replace the batteries to avoid any
damage to the watch.
1. Open and carefully remove the back of
the watch.
2. Lift up the battery spring on the
bottom.
3. Remove the battery and insert a new
one with the polarity "+" facing up.
4. Push the battery spring down until it
locks.
5. Before you replace the case-back,
make sure the seal is in place.
6. The watch confirms the hands position
automatically 10 minutes after a new
battery is installed.
13
7. Set the watch in a location where
signal reception is possible and wait
until the watch sets itself automatically.
This will take from 1 to 24 hours.
8. After battery replacement the watch
defaults to Pacific Time Zone. Set your
Time Zone as necessary after the
watch picks up the signal. Go to “Time
Zone Setting” section for details.
Reset Procedure / Set the Hands to
12 o'clock Manually:
On rare occasions if the watch hands have
not automatically stopped at 12 o'clock
before battery replacement, first change
the battery as described in "Battery
Replacement” section. Immediately
following battery replacement all hands
(hour, minute and second hands) have to
be moved to the 12 o'clock position
(12:00:00) manually to reset the watch.
The watch will not run until re-initialized.
Follow the steps below.
Another instance when you may need to
perform the Reset Procedure below would
be if your watch does not display the
correct time after you have done the
following steps: you have re-calibrated
the watch, you have set the watch to your
14
correct time zone, and the watch has
picked up the time signal but the time
displayed is still incorrect.
1.
3
4
Immediately after battery has been
replaced hold 2 o clock button until the
hands move quickly. You can stop the
fast movement by pressing 2 o'clock
button again.
. Stop the fast movement just before the
second hand reaches the 12 o'clock
position (i.e. 11:45:00) by pressing 2
o'clock button.
. Adjust the second-hand to move it to
the 12 o'clock position (12:00:00) by
pressing/releasing the 2 o'clock button
one second at a time. (If you
accidentally go past the 12, start this
process again.)
. When all hands are aligned at the 12
o'clock position (12:00:00), Push 10
o'clock button for 1 second to confirm.
After confirmation, follow the
procedure below after the watch
resumes running:
a:Set the watch to your correct Time
Zone as necessary. (Watch defaults
to Pacific Time Zone after battery
replacement.)
b:Set your Local Time manually (go to
“Manual Time Setting” section for
15
details). You don,t need to set to the
exact minute and second but make
sure HOUR and AM or PM time of
day are correct. Your watch will
synchronize to the Atomic clock after
it receives the signal (the reason to
set time is to make sure your watch
will initiate signal reception at
around 3AM local time.)
c:Put the watch in a location where
reception is possible. The watch will
automatically initiate a reception at
3AM. After receiving a valid time
signal, the hands move on to the
correct time.
Battery Lifetime and Replacement:
Talking Requests per Battery Life
Day
О 2 Years
= 1 Years
10 8 Months
15 6 Months
20 5 Months
25 4 Months
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement