Biasi RIVA PLUS HE 24C ERP User Manual and Installation Instructions

Wall hung, fanflue, roomsealed, high efficiency gas boiler
User manual and
Installation instructions
Riva Plus HE ERP
Models
G.C. Appl. No.
RIVA PLUS HE 24C ERP 47-583-41 COMBI BOILER
RIVA PLUS HE 28C ERP 47-583-42 COMBI BOILER
WARNING
Congratulations on your choice.
Riva Plus HE ERP are condensing high efficiency sealed chamber fan flue gas boilers. They
are fully electronically controlled and have electronic ignition.
The materials they are made of and the control systems they are equipped with give you
safety, a high level of comfort and energy savings to allow you to get the greatest benefit out
of independent heating.
Riva Plus HE ERP allow a higher efficiency by reducing the flue gas temperature such that
the water vapour formed during the combustion is condensed out.
This allows a gain of useful heat that otherwise would be lost.
Biasi UK Ltd is a licensed member of the Benchmark Scheme which aims to improve the
standards of installation and commissioning of domestic heating and hot water systems in
the UK and to encourage regular servicing to optimise safety, efficiency and performance.
Benchmark is managed and promoted by the Heating and Hot water Industry Council. For
more information visit www.centralheating.co.uk.
DANGER: The indications marked with this symbol must be observed to prevent accidents of mechanical or generic origin (e.g.: Injuries or bruises).
DANGER: The indications marked with this symbol must be observed to prevent accidents of electric origin (electrocution).
DANGER: The indications marked with this symbol must be observed to prevent the risk of fire or explosion.
DANGER: The indications marked with this symbol must be observed to prevent accidents of heat origin (burns).
ATTENTION: The indications marked with this symbol must be observed to
prevent malfunctioning and/or damage to materials of the appliance or other
objects.
ATTENTION: The indications marked with this symbol is important information that must be carefully read.
-2-
The manual must be read thoroughly, so that you will be able to use the boiler in a safe
and sensible way; must be carefully kept. It may be necessary for reference in the future.
The lighting up must be carried out by competent and responsible engineer.
The manufacturer
• disclaim all liability for any translations of the present manual from which incorrect interpretation may occur;
• cannot be held responsible for non-observance of instructions contained in this manual
or for the consequences of any procedure not specifically described.
Please ensure that the installer has fully completed the Benchmark Checklist on the inside
back pages of the installation instructions supplied with the product and that you have signed
it to say that you have received a full and clear explanation of its operation. The installer is
legally required to complete a commissioning checklist as a means of complying with the
appropriate Building Regulations (England and Wales).
All installations must be notified to Local Area Building Control either directly or through a
Competent Persons Scheme. A Building Regulations Compliance Certificate will then be
issued to the customer who should, on receipt, write the Notification Number on the Benchmark Checklist.
This product should be serviced regularly to optimise its safety, efficiency and performance.
The service engineer should complete the relevant Service Record on the Benchmark
Checklist after each service.
The Benchmark Checklist will be required in the event of any warranty.
Using the boiler...
Before lighting the boiler you are advised to have a Gas Safety Registered Engineer
check that the installation of the gas supply
• is gas-tight;
• is of the correct gauge for the flow to the boiler;
• is fitted with all the safety and control devices required by the current Regulations.
Ensure that
• check with the Installer that he has connected and terminated the pressure relief valve
in a manner which allows safe discharge. The manufacturers are not responsible for
damage caused by opening of the pressure relief valve and consequent escape of water, if this is not connected and terminated;
• the installer has connected the condensate outlet to a suitable drain pipe.
-3-
WARNING
Remember that...
WARNING
On detecting the smell of gas:
• don’t operate any electrical switches, the telephone or any device that may produce
sparks;
• open the windows and doors at once to create a draught of air which will purge the area;
• shut off the gas cocks;
• get the assistance of a qualified person. Emergency telephone number
Tel 0800 111999.
Do not touch the appliance with parts of the body that are wet or damp and/or bare feet.
Do not block or modify the condensate outlet and pipework.
In case of structural work or maintenance near the exhaust duct and/or fume exhaust
devices or their attachments, turn off the appliance. On completion of the work, have a
professionally qualified person check their efficiency.
Repairs (under guarantee) must be carried out only by a Biasi an approved engineer, using genuine spare parts. Thus do no more than switching off the boiler yourself (see the
instructions).
Your boiler allows heating up of water to a temperature less than boiling point;
• must be connected to a central heating system and/or a hot water supply system, compatible with its performance and output;
• can be used only for those purposes for which it has been specially designed;
• must not be touched by children or by those unfamiliar with its operation;
• must not be exposed to weather conditions.
During the operation it is quite normal that the boiler produces a white plume of condensation vapour from the flue terminal. This is due to the high efficiency of the appliance and
may be particularly evident with low outdoor temperatures.
Safe handling of substances
Biasi products are manufactured in accordance with ISO 9001 and do not, and will not,
contain any hazardous materials or substances such as asbestos, mercury or C.F.C.’s. The
appliance packaging does not contain any substances, which may be considered a hazard
to health.
When handling or lifting always use safe techniques
• keep your back straight, bend your knees, don't twist;
• move your feet, avoid bending forwards and side way sand keep the load as close to your
body as possible.
Where possible transport the boiler using a sack truck or other suitable trolly.
Always grip the boiler firmly, and before lifting feel where the weight is concentrated to establish the centre of gravity, repositioning yourself as necessary.
-4-
Thermostat / Temperature gauge
Description - Sealed phial and capillary containing liquid.
Known hazards - irritating to skin, eyes and throat. Vapour is harmful. Inflammable -do not
extinguish with water.
Precautions - Do not incinerate. Avoid contact with broken/leaking phials. Do not purposely
puncture.
First aid - medical attention must be sought following eyes/skin contact, wash with clean
water.
Sharp Edges
Caution should be taken when handling the boiler to avoid sharp edges on the boiler.
Boiler installation and commissioning tips
The installation must be carried out by a qualified Gas Safety Registered Engineer who
will be responsible for observing the current Regulations and the completion of the
Benchmark Gas Boiler System Commissioning Checklist, located at the back of this User
manual.
Internally installed mains water meters
Please ensure if the property has had a water meter installed inside the property that it does
not include a non-return valve, should you find that it does include a non-return valve then
provision of a WRAS approved mini expansion vessel must be made.
Biasi optional WRAS approved easy fit 15 mm mini shock arrestor kit BI9999 999 can
be obtained through your local Biasi stockist.
-5-
WARNING
Combustion chamber panels
Material: mineral fibres
Known hazards - Some people can suffer reddening and itching of the skin. Fibre entry into
the eye will cause foreign body irritation, which can cause severe irritation to people wearing
contact lenses. Irritation to respiratory tract.
Precautions - Dust goggles will protect eyes. People with a history of skin complaints may
be particularly susceptible to irritation. High dust levels are only likely to arise following harsh
abrasion. In general, normal handling and use will not present high risk, follow good hygiene
practices, wash hands before, touching eyes, consuming food, drinking or using the toilet.
First aid - Medical attention must be sought following eye contact or prolonged reddening of
the skin.
WARNING
Installing the boiler...
Do not forget to remove the transit caps and plugs from the boiler connections these are
fitted to every boiler.
Keep the boiler clear of dust during installation and in particular do not allow any dust or
debris to enter the top of the boiler where the flue connection is made. It is recommended
that you put a dust sheet over the top of the boiler until you are ready to make the flue
connection.
Remember to release the auto air purge before filling the boiler. See the instructions to
identify the location of this device.
This boiler allows to control the flow temperature of the central heating system at very
low levels. In case of underfloor heating system a temperature limiting device (e.g. a
safety thermostat) is recommended to stop the boiler in case that the water temperature
exceeds the design temperature.
You are strongly advised to the British Standard BS 7593-2006 Code of practice,flush out
the system both cold and hot in order to remove system and installation debris.
It is also sensible to initially fire and commission the boiler before connecting any external
controls such as a room thermostat. By following this procedure if you have a subsequent
problem this method if you have a subsequent problem following the addition of an external control you can eliminate the boiler from your fault analysis.
If the boiler is fitted with a digital programmer, when setting the times for automatic operation, remember that for every “ON” time there must be an “OFF” time to follow and that
on every occasion you enter a time you must also indicate which days that you want the
boiler to follow the timed settings.
Some products incorporate an anti cycling time delay. It is normal when first switching the
boiler on for the boiler to operate on heating for a few seconds then switch off. After 3 - 4
minutes has elapsed the boiler will then re ignite and operate perfectly normally. The ignition delay cycle does not prevent normal operation of the boiler to provide d.h.w.
If you are in any doubts as to the installation or operation of the boiler please read the
instruction manuals thoroughly and then if necessary contact Biasi UK for advice and assistance.
Guarantee conditions. The guarantee registration form must be returned within 30 of
purchase, failure to comply will invalidate the guarantee.
Please remember that if you are in any doubt about the installation of this product you can
contact our Technical Helpline on tel. 01922 714 600.
Abbreviations used in the manual:
C.h. = Central heating
D.h.w. = Domestic hot water
D.c.w. = Domestic cold wate
-6-
TABLE OF CONTENTS
1 APPLIANCE DESCRIPTION . . . . . . . . . . . . 8
1.1
1.2
1.3
1.4
1.5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Isolation valves . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation lights . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
8
8
9
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Refilling procedure . . . . . . . . . . . . . . . . . . . . . . . 10
Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
C.h. circuit temperature . . . . . . . . . . . . . . . . . . . 11
D.h.w. temperature . . . . . . . . . . . . . . . . . . . . . . 12
Extinguishing . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Built in time switch A . . . . . . . . . . . . . . . . . . . . . 13
Built in time switch B . . . . . . . . . . . . . . . . . . . . . 15
Built in time switch C . . . . . . . . . . . . . . . . . . . . . 17
Built in time switch D . . . . . . . . . . . . . . . . . . . . . 20
3.1
3.2
3.3
3.4
3.5
3.6
Central Heating . . . . . . . . . . . . . . . . . . . . . . . . .
Frost protection . . . . . . . . . . . . . . . . . . . . . . . . .
Condensate drain . . . . . . . . . . . . . . . . . . . . . . .
Periodic maintenance . . . . . . . . . . . . . . . . . . . .
External cleaning . . . . . . . . . . . . . . . . . . . . . . . .
Operational faults . . . . . . . . . . . . . . . . . . . . . . .
23
23
23
23
23
24
4.1
4.2
4.3
4.4
4.5
4.6
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main diagram . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic specifications . . . . . . . . . . . . . . . . . . .
Expansion vessel . . . . . . . . . . . . . . . . . . . . . . . .
Technical data mod. Riva Plus HE 24C ERP . .
Technical data mod. Riva Plus HE 28C ERP . .
26
27
29
29
30
34
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
Related documents . . . . . . . . . . . . . . . . . . . . . .
Location of appliance . . . . . . . . . . . . . . . . . . . . .
Flue system . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condensate drain . . . . . . . . . . . . . . . . . . . . . . .
Water circulation (c.h.) . . . . . . . . . . . . . . . . . . . .
Domestic water . . . . . . . . . . . . . . . . . . . . . . . . .
Water treatment . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical supply . . . . . . . . . . . . . . . . . . . . . . . . .
38
38
39
39
40
40
40
41
42
42
42
2 INSTRUCTIONS FOR USE . . . . . . . . . . . . 10
3 USEFUL ADVICE . . . . . . . . . . . . . . . . . . . . 23
4 TECHNICAL INFORMATION . . . . . . . . . . . 26
5 GENERAL REQUIREMENTS . . . . . . . . . . . 38
6INSTALLATION . . . . . . . . . . . . . . . . . . . . . . 43
6.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.2 Precautions for installation . . . . . . . . . . . . . . . . 43
6.3 Installing the bracket . . . . . . . . . . . . . . . . . . . . .
6.4 Overall dimensions . . . . . . . . . . . . . . . . . . . . . .
6.5Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6 Mounting the boiler . . . . . . . . . . . . . . . . . . . . . .
6.7 Fitting the flue system . . . . . . . . . . . . . . . . . . . .
6.8 Choice of flue . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.9 Electrical connections . . . . . . . . . . . . . . . . . . . .
6.10 External frost protection . . . . . . . . . . . . . . . . . . .
44
44
45
45
45
46
48
50
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
7.12
7.13
7.14
51
51
51
51
51
53
53
54
55
55
55
56
56
56
7COMMISSIONING . . . . . . . . . . . . . . . . . . . 51
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical installation . . . . . . . . . . . . . . . . . . . . .
Gas supply installation . . . . . . . . . . . . . . . . . . . .
Filling the d.h.w. system . . . . . . . . . . . . . . . . . .
Initial filling of the system . . . . . . . . . . . . . . . . . .
Condensate pipe and traps . . . . . . . . . . . . . . . .
Lighting the boiler . . . . . . . . . . . . . . . . . . . . . . .
Checking the gas pressure at the burner . . . . .
Checking the burner ignition . . . . . . . . . . . . . . .
Checking the ignition device . . . . . . . . . . . . . . .
Checking the flue system . . . . . . . . . . . . . . . . .
Check pump operation/pump release . . . . . . . .
Checking the condensate drain pipe . . . . . . . .
Instructing the user . . . . . . . . . . . . . . . . . . . . . .
8 GAS CONVERSION . . . . . . . . . . . . . . . . . . 57
8.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
8.2Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
9MAINTENANCE . . . . . . . . . . . . . . . . . . . . . 59
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
9.11
9.12
9.13
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismantling the external panels . . . . . . . . . . . .
Emptying the d.h.w. system . . . . . . . . . . . . . . . .
Emptying the c.h. system . . . . . . . . . . . . . . . . .
Combustion analysis check . . . . . . . . . . . . . . . .
Cleaning the primary heat exchanger . . . . . . . .
Checking the pressurisation in the expansion
vessel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the burner . . . . . . . . . . . . . . . . . . . . . .
Checking the flue . . . . . . . . . . . . . . . . . . . . . . . .
Drain pipe inspection . . . . . . . . . . . . . . . . . . . . .
Visual inspection of appliance . . . . . . . . . . . . . .
Gas pressures and tightness . . . . . . . . . . . . . . .
Water inhibitor concentration . . . . . . . . . . . . . . .
59
59
59
59
60
60
Gas boiler system commissioning checklist . . . 62
Service record . . . . . . . . . . . . . . . . . . . . . . . . . . 63
60
60
60
60
60
60
60
10BENCHMARK COMMISSIONING AND SERVICING SECTION . . . . . . . . . . . . . . . . . . . . 61
Appliance category: II2H3+ (Gas G20 20 mbar, G30 29 mbar, G31 37 mbar)
Country of destination: United Kingdom (GB) Ireland (IE)
This appliance conforms with the following EEC directive:
Gas Directive 2009/142/CE
Boiler Efficiency Directive 92/42/CEE
Electromagnetic Compatibility Directive 2004/108/CE
Low Voltage Directive 2006/95/CE
The manufacturer, in the continuous process to improve his products, reserves the right to modify the data expressed in
the present documentation at any time and without prior notice.
The present documentation is an informative support and it can not be considered as a contract to-wards third parties.
-7-
APPLIANCE DESCRIPTION
1
APPLIANCE DESCRIPTION
1.1
Overview
The model and serial number of the boiler
are printed on bottom right side.
9 D.h.w. temperature control knob
10 Appliance operation lights
1.3
Isolation valves
Provide for the installation
of a stop valve on the D.c.w.
inlet pipe.
USE
1
2
16 15
3
Fig. 1.1
Control panel
4 C.h. circuit temperature and pressure
gauge
5 Time switch (c.h. control)
6 Lock-out signal lamp
7 Lockout reset button
8 Function selector and c.h. temp. control
knob
Fig. 1.3
-8-
10
9
11
12
Fig. 1.2
1 Case front panel
2 Control panel
3 Control panel cover
1.2
14 13
8
76
11 Condensate drain pipe
12 C.h. return valve
13 D.c.w. inlet valve
14 Gas inlet valve
15 D.h.w. outlet pipe
16 C.h. flow valve
1.4
Technical data
For detailed technical data see sections
"Technical Data" on pag. 30 or pag. 34.
5
4
APPLIANCE DESCRIPTION
Operation lights
Three lights (10 in Fig. 1.3) give detailed
indication regarding the operation of the
boiler.
The following table gives the relationship
between each of the possible light combinations and their meaning.
Faulty c.h. temperature
probe NTC
Faulty d.h.w temperature
probe NTC
Faulty flue temperature
probe NTC
A short pulse every 4 seconds: stand-by condition
Faulty primary circuit
(no water or low c.h.
pressure)
position.
Anti-freeze system active
1 second pulse every 2
seconds: normally operating boiler. Function
selector in
sition
or
Faulty primary circuit
(absence of flow)
Faulty air pressure sensor
po-
Lack of burner ignition (no
ignition signal from the full
sequence ignition device)
C.h. operation
D.h.w. operation
Safety thermostat lock
out
Frost protect operation
Flue temperature probe
NTC lock out
D.h.w. operation
Excessive temperature
on primary circuit
If the lights combination observed is not
included in the above table a fault may be
indicated.
Reference should be made to the following
table.
In this case switch off the boiler, as described in section "Extinguishing" to page
13 and call a competent and responsible
Service Engineer.
Flame detection error
Other faults
Lack of power supply or
fauly electr. control p.c.b.
Meaning of symbols:
Lamp OFF
Lamp ON
Flashing lamp, alone or simultaneously with an other lamp
Flashing lamp, alternate with another
lamp
-9-
USE
1.5
INSTRUCTIONS FOR USE
2
USE
2.1
INSTRUCTIONS FOR USE
Warnings
Biasi UK Ltd support the Benchmark initiative. The Benchmark Checklist is located at the back of this manual and should
be completed by the Installing/Commissioning Engineer and handed over to the
User for future reference by other visiting
Engineers. Also included is the Service
Interval Record card that should be completed by the Service Engineer following
the annual service maintenance of the
boiler and system.
All Gas Safe Registered Installers carry a
Gas Safe ID card, and have a registration
number. Both should be recorded in your
Benchmark Checklist. You can check
your Installer is registered by calling Gas
Safe direct on 0800 408 5500, or go on
line at www.GasSafeRegister.co.uk.
In order to guarantee safety and correct operation, it is essential that all the tests are
carried out by a competent and responsible
service engineer before lighting up the boiler.
The tests are described in the installation instructions in section 7 commissioning.
Ensure that the c.h. circuit is regularly filled
with water (even if the boiler is only used for
d.h.w. supply) checking that the pressure
indicated on pressure gauge 4 is not lower
than that shown in Fig. 2.2.
If the pressure reading on the pressure
gauge is below that shown in Fig. 2.2, then
the system will require topping up. A filling
loop is normally provided by the Installer for
this purpose.
If you are in any doubt regarding this procedure you are advised to contact your
Installer or an Approved Engineer.
- 10 -
This appliance is provided with a built in antifreeze system that operates the boiler when
the temperature is below 5 °C.
Therefore, when the boiler is not lit or used
in cold weather, with consequent risk of
freezing do not switch off the boiler at the
fused spur isolation switch or close the
gas inlet cock.
When you do not expect to use the boiler
for a long period and the boiler is not to be
used for frost protection then follow the instructions given in section "Extinguishing" to
page 13.
2.2
Refilling procedure
• Isolate the boiler from the electrical supply
at the fused spur. Reconnect the filling loop
as demonstrated in Fig. 2.1.
Control
valve
Double
check valve
Temporary
connection
Supply pipe
(cold water
inlet)
Fig. 2.1
Control valve
C.h. return pipe
• Open the valves of the filling loop and
watch the gauge until it reaches normal filling pressure as shown in Fig. 2.2.
4
Normal
filling
pressure
Fig. 2.2
INSTRUCTIONS FOR USE
• Close the valves and remove the filling
loop.
flash every 2 seconds (operating boiler).
If you experience any difficulty with the
operation of the boiler, switch off the boiler immediately at the fused spur isolation
switch and contact your Installer or an
approved Service Engineer.
2.3
10
Fig. 2.4
8
• If d.h.w. supply only is required, position
the function selector 8 as in Fig. 2.5. The
appliance operation light 10 will flash every
2 seconds (operating boiler).
Ignition
• Check that the valves located in the lower
part of the boiler are open Fig. 2.3.
10
Fig. 2.5
2.4
Open position
Fig. 2.3
• Turn on the electricity supply to the boiler switching on the fused spur isolation
switch. The appliance operation light 10
(Fig. 2.4) will flash every 4 seconds (standby condition).
• If the boiler is to be used for c.h. and d.h.w,
position the function selector 8 as in Fig.
2.4. The appliance operation light 10 will
8
C.h. circuit temperature
The output temperature of c.h. water is adjustable from a minimum of about 40°C to a
maximum of about 85°C (Fig. 2.6), by turning
the function selector (8).
Adjustment of c.h. output on the boiler is automatic.
The greatest output pre-set in the factory
can, however, be reduced in level according
to actual system requirements; this does not
affect the maximum output in d.h.w. operation.
Such adjustments must be carried out by a
qualified person; therefore we advise you to
contact your installer or Service Agent.
Adjustment of the boiler temperature alters
- 11 -
USE
Air introduced into the boiler during this filling process will vent through the automatic
air purger fitted to the boiler. You may also
find it necessary to vent air from your radiator circuit using your radiator key, however
be aware that excessive venting will cause
the pressure in the system to drop.
Always ensure that the pressure gauge is set
at the required pressure.
INSTRUCTIONS FOR USE
the gas flow at the burner according to the
thermal demand in the system. So it is usual
to see the burner lit at the minimum level for
more or less long periods.
boiler can be varied from a minimum of about
35°C to a maximum of about 55°C (Fig. 2.8),
by turning the temperature control knob 9.
Minimum
Minimum
Maximum
USE
Maximum
Fig. 2.6
Fig. 2.8
Adjustment
In order to achieve optimal settings for economy and comfort, we recommend adjusting
the operating temperature of the c.h. water
according to the outside temperature, positioning the knob as follows:
Adjustment of the d.h.w. temperature is completely separate from that of the c.h. circuit.
The adjustment system integrated within the
boiler automatically controls the flow of gas
to the burner in order to keep the temperature of d.h.w. delivered constant, between
the limits of maximum and minimum output.
Where the demand is at a low level or with
the temperature set to the minimum, it is normal to see a cycle of lighting and extinguishing of the burner when running.
From 5 to 15 °C
Between
- 5 and +5 °C
Lower
than - 5 °C
Fig. 2.7
Your qualified installer will be able to recommend the most suitable adjustment for your
system.
The temperature and pressure gauge (4,
Fig. 1.3 on page 8) will allow you to check
that the set temperature is obtained.
2.5
D.h.w. temperature
The temperature of the d.h.w. leaving the
- 12 -
Adjustment
It is advisable to adjust the d.h.w. temperature to a level commensurate with the demand, minimising the need to mix with cold
water. In this way, the automatic control facilities will be fully exploited.
Moreover, where the amount of limescale
present in the water may be particularly
great, not exceeding the position in Fig. 2.9
of the d.h.w. temperature control knob 9 corresponding to about 50°C (Fig. 2.9),minimises annoying incidences of scale deposits
and clogging.
INSTRUCTIONS FOR USE
Fig. 2.9
In these cases, however, it is advisable to
install a small water treatment device or softener. With such a device you should avoid
periodic descaling.
Consequently, the d.h.w. heat exchanger will
keep its performance consistent for a longer
period of time with resulting gas savings.
If the demand for d.h.w. is so great as to prevent reaching a high enough temperature,
have the appropriate output limiting valve
installed by your installer or an Authorised
Service Engineer.
2.6
USE
switch.
• Shut off the gas supply cock 14 and the
valves for the water circuits fitted under the
boiler (Fig. 2.11).
• Empty the water circuits, if necessary,
as shown in section General access and
emptying hydraulic circuits in the service
manual.
14
Fig. 2.11
2.7
Closed position
Built in time switch A
The boilers are equipped with a built in electronic time switch (5, Fig. 1.3 on page 8)
which controls the c.h. operation.
Extinguishing
To turn the boiler off set the function selector
8 to the position shown in Fig. 2.10.
The appliance operation light 10 will flash
every 4 seconds.
H
G
A
10
Fig. 2.10
8
When you do not expect to use the boiler for
a long period:
• Switch off the electricity supply to the boiler, by means of the fused spur isolation
F
Fig. 2.12
E
D
C
B
Display and control panel:
A Mode selector switch
B Reset button
C Enter button
- 13 -
INSTRUCTIONS FOR USE
USE
D
E
F
G
H
Increase “+” setting button
Decrease “-” setting button
On-off button
Time display
ON-OFF display
Setting the current time
Note: with a new unit or when the reset button B has been pressed and the selector
switch A is to the position, the time display
G is flashing.
Set the mode selector switch A to the position and press the buttons D or E until the
current time appears in the display G.
The clock starts by moving the switch A to
the AUTO position.
Setting example shown in Fig. 2.13:
Current time 16.30.
ON setting and confirm by pressing the “enter” button C. Proceed in the same way for
other settings.
Setting example shown in Fig. 2.15:
I ON time 7.45.
J OFF time 10.30.
Fig. 2.15
I
J
Activating the timed settings
Set the mode selector switch A to the AUTO
position shown in Fig. 2.16.
The current time appears in the display. The
ON-OFF display H indicates the current
state of operation (according to the settings).
A
A
Fig. 2.13
Fig. 2.16
Setting the switching time
20 memory locations are available, corresponding to 10 on-off sequences.
Set the mode selector switch A to the C1 position.
The symbols shown in Fig. 2.14 appears in
the display.
Note: when the mode selector switch A is in
the AUTO position and the boiler is switched
off at the fused spur isolation switch, the
display H indicates only the OFF state. The
other indications are blanked.
A
Fig. 2.14
Press the buttons D or E to set the desired
ON time. Press the “enter” button C to confirm the setting and to continue programming
the OFF time.
Set the OFF time as explained above for the
- 14 -
Reading the timed settings
Set the mode selector switch A to the C1 position. The symbols shown in Fig. 2.14 appears in the display.
Press the “enter” button C. Each time the
button is pressed the display shows the details of the next setting.
Changing or deleting the timed settings
Set the mode selector switch A to the C1 position. The symbols shown in Fig. 2.14 appears in the display.
INSTRUCTIONS FOR USE
Manual operation
The operation of the time switch can be
forced on or off constantly or for a timed period.
To force constantly on or off the timer operation set the mode selector switch A to the
TIMER position. The symbols shown in Fig.
2.17 appears on the display.
Fig. 2.17
The operation can be switched permanently
on or off by pressing the button F and leaving
the switch A in the TIMER position. To force a
timed delay on or off operation, set the mode
selector switch A in the TIMER position.
Set the time delay by pressing the button D
or E and the operation can be forced on or
off by pressing the button F.
The time delay can be set within the following ranges:
1 to 23 hours with steps of 1 hour
1 to 27 days with steps of 1 day.
The time delay setting is activated by moving
the switch A to the AUTO position.
The ON-OFF display H flashes indicating
that the current state of operation has been
forced.
To delete the timed delay setting, set the
mode selector switch A in the TIMER position, press the button D or E until the symbols shown in Fig. 2.17 appears in the display and then set the mode selector switch A
to the AUTO position.
Setting example shown in Fig. 2.18:
forced ON state for 4 hours.
USE
Press the “enter” button C until the display
shows the setting to be modified or deleted.
The time setting can be modified now by
pressing button D or E and the operation can
be switched on or off by pressing the button
F.
To delete a time set press the button D or E
until the symbols shown in Fig. 2.14 appears
in the time display G.
The new settings are memorized by moving
the switch A to a different position.
Fig. 2.18
Resetting
To completely reset the timer, press the reset
button with a pointed object (pencil).
CAUTION: pushing the reset button will
completely erase the settings as well as all
the data, including the current time.
2.8
Built in time switch B
The combiboilers are equipped with a built
in electronic time switch which controls the
c.h. operation.
H
G
A
F
Fig. 2.19
D
E
C
B
- 15 -
INSTRUCTIONS FOR USE
USE
Display and control panel
A Mode selector switch
B Reset button
C OK button
D Increase “+” setting button
E Decrease "-” setting button
F On-off button
G Time display
H ON-OFF display
Set the OFF time as explained above for the
ON setting and confirm by pressing the “OK”
button C. Proceed in the same way for other
settings.
Setting example shown in Fig. 2.22:
K ON time 7.45.
L OFF time 10.30.
Setting the current time
Press repeatedly the button A until the display shows the symbol .
Press the buttons D or E until the current
time appears in the display G.
The clock starts by pressing the button A to
show the symbol AUTO.
Setting example shown in Fig. 2.20:
Current time 16.30, day Thursday.
Fig. 2.22
K
L
Activating the timed settings
The current time appears in the display. The
ON-OFF display H indicates the current
state of operation (according to the settings).
A
A
Fig. 2.20
Setting the switching time
28 memory locations are available, corresponding to 14 on-off sequences.
Press repeatedly the button A until the display shows the symbol C1.
The symbols shown in Fig. 2.21 appears in
the display.
Fig. 2.23
Note: when the display shows the symbol
AUTO and the boiler is switched off at the
fused spur isolation switch, the display H indicates only the OFF state. The other indications are blanked.
Fig. 2.21
Reading the timed settings
Press repeatedly the button A until the display shows the symbol C1 (Fig. 2.21).
The symbols shown in Fig. 2.21 appears in
the display.
Press the “OK” button C. Each time the button is pressed the display shows the details
of the next setting.
Press the buttons D or E to set the desired
ON time. Press the “OK” button C to confirm
the setting and to continue programming the
OFF time.
Changing or deleting the timed settings
Press repeatedly the button A until the display shows the symbol C1 (Fig. 2.21).
The symbols shown in Fig. 2.21 appears in
A
- 16 -
the display.
Press the “OK” button C until the display
shows the setting to be modified or deleted.
The time setting can be modified now by
pressing button D or E and the operation can
be switched on or off by pressing the button
F.
To delete a time set press the button D or E
until the symbols shown in Fig. 2.21 appears
in the time display G.
The new settings are memorised by pressing
the button A.
Manual operation
The operation of the time switch can be
forced on or off constantly or for a timed period.
To force constantly on or off the timer operation press repeatedly the button A until
the display shows the symbol TIMER. The
symbols shown in Fig. 2.24 appears on the
display.
A
Fig. 2.24
The operation can be switched permanently
on or off by pressing the button F and leaving
the display shows the symbol TIMER.
To force a timed delay on or off operation,
press repeatedly the button A until the display shows the symbol TIMER.
Set the time delay by pressing the button D
or E and the operation can be forced on or
off by pressing the button F.
Press the button A until the display shows
the symbol AUTO.
The ON-OFF display H flashes indicating
that the current state of operation has been
forced.
To delete the timed delay setting, press repeatedly the button A until the display shows
the symbol TIMER, press the button D or E
until the symbols shown in Fig. 2.25 appears
in the display and then press the button A until the display shows the symbol
AUTO.
Setting example shown in Fig. 2.25:
forced ON state for 4 hours.
A
Fig. 2.25
Note: If during manual operation, power supply turns off, timer must be set again following previous steps.
Resetting
To completely reset the timer, press the reset
button with a pointed object (pencil).
CAUTION: pushing the reset button will
completely erase the settings as well as all
the data, including the current time.
2.9
Built in time switch C
The combi boilers are equipped with a built
in electronic time switch (5, Fig. 1.3 on page
8) which controls the c.h. operation.
The time delay can be set within the following ranges:
1 to 23 hours with steps of 1 hour
1 to 27 days with steps of 1 day.
- 17 -
USE
INSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE
J
I
A
H
A
G
Fig. 2.27
USE
F
Fig. 2.26
E
D
C
B
Display and control panel:
A Mode selector switch
B Reset button
C Enter button
D Increase “+” setting button
E Decrease “-” setting button
F On-off button
G Day selection buttons
H Day display
I Time display
J ON-OFF display
Setting the current time and weekday
Note: with a new unit or when the reset button B has been pressed, the first day indicator H on the left and the time display I is
flashing.
Set the mode selector switch A to the position and press the buttons D or E until the
current time appears in the display I.
Press the day selection button corresponding to the current day, considering that button 1=Monday, button 2=Tuesday and so on.
The clock starts by moving the switch A to
the AUTO position.
Setting example shown in Fig. 2.27:
Current time 16.30, day Thursday.
- 18 -
Setting the switching time and day (or
days)
20 memory locations are available, corresponding to 10 on-off sequences.
Set the mode selector switch A to the C1 position.
The symbols shown in Fig. 2.28 appears in
the display.
A
Fig. 2.28
Press the buttons D or E to set the desired
ON time.
Press the buttons G to set the desired day or
days of operation.
Press the “enter” button C to confirm the setting and to continue programming the OFF
time.
Set the OFF time as explained above for the
ON setting and confirm by pressing the “enter” button C. Proceed in the same way for
other settings.
Setting example shown in Fig. 2.29:
K ON time 7.45, day Monday to Friday.
L OFF time 10.30, day Monday to Friday.
Fig. 2.29
K
L
Activating the timed settings
Set the mode selector switch A to the AUTO
position shown in Fig. 2.16.
The current time and day appears in the display. The ON-OFF display J indicates the
current state of operation (according to the
settings).
A
Fig. 2.30
Note: when the mode selector switch A is in
the AUTO position and the boiler is switched
off at the fused spur isolation switch, the
display J indicates only the OFF state. The
other indications are blanked.
Reading the timed settings
Set the mode selector switch A to the C1 position. The symbols shown in Fig. 2.28 appears in the display.
Press the “enter” button C. Each time the
button is pressed the display shows the details of the next setting.
Changing or deleting the timed settings
Set the mode selector switch A to the C1 position. The symbols shown in Fig. 2.28 appears in the display.
Press the “enter” button C until the display
shows the setting to be modified or deleted.
The day display H gives a flashing indication
of the active day or group of days.
Press the button (or the buttons) G corresponding to the day (or days) for which it is
intended to apply the modification. The corresponding day display stops flashing and a
new switching time can be set or deleted.
The time setting can be modified now by
pressing button D or E and the operation can
be switched on or off by pressing the button
F.
To delete a time set press the button D or E
until the symbols shown in Fig. 2.28 appears
in the time display I.
The new settings are memorized by moving
the switch A to a different position.
Manual operation
The operation of the time switch can be
forced on or off constantly or for a timed period.
To force constantly on or off the timer operation set the mode selector switch A to the
TIMER position. The symbols shown in Fig.
2.31 appears on the display.
Fig. 2.31
The operation can be switched permanently
on or off by pressing the button F and leaving the switch A in the TIMER position. To
force a timed delay on or off operation, set
the mode selector switch A in the TIMER position.
Set the time delay by pressing the button D
or E and the operation can be forced on or
off by pressing the button F.
- 19 -
USE
INSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE
USE
The time delay can be set within the following ranges:
1 to 23 hours with steps of 1 hour
1 to 27 days with steps of 1 day
The time delay setting is activated by moving
the switch A to the AUTO position.
The ON-OFF display J flashes indicating
that the current state of operation has been
forced.
To delete the timed delay setting, set the
mode selector switch A in the TIMER position, press the button D or E until the symbols shown in Fig. 2.31 appears in the display and then set the mode selector switch A
to the AUTO position.
Setting example shown Fig. 2.32:
forced ON state for 4 hours.
Fig. 2.32
Resetting
To completely reset the timer, press the reset
button with a pointed object (pencil).
CAUTION: pushing the reset button will
completely erase the settings as well as all
the data, including the current time and day.
2.10 Built in time switch D
The combi boilers are equipped with a built
in electronic time switch (5on page 8) which
controls the c.h. operation.
- 20 -
J
I
H
A
G
Fig. 2.33
F
D
E
C
B
Display and control panel
A Mode selector switch
B Reset button
C OK button
D Increase “+” setting button
E Decrease "-” setting button
F On-off button
G Day selection buttons
H Day display
I Time display
J ON-OFF display
Setting the current time and weekday
Note: with a new unit or when the reset button B has been pressed, the first day indicator H on the left and the time display I are
flashing.
Press repeatedly the button A until the display shows the symbol .
Press the buttons D or E until the current
time appears in the display I.
Press the day selection button G corresponding to the current day, considering that
button 1=Monday, button 2=Tuesday and so
on.
The clock starts by pressing the button A to
show the symbol AUTO.
Setting example shown in Fig. 2.34:
INSTRUCTIONS FOR USE
Current time 16.30, day Thursday.
A
Activating the timed settings
The current time and day appears in the display. The ON-OFF display J indicates the
current state of operation (according to the
settings).
Fig. 2.34
A
A
Fig. 2.35
Press the buttons D or E to set the desired
ON time.
Press the buttons G to set the desired day or
days of operation.
Press the “OK” button C to confirm the setting and to continue programming the OFF
time.
Set the OFF time as explained above for the
ON setting and confirm by pressing the “OK”
button C. Proceed in the same way for other
settings.
Setting example shown in Fig. 2.36:
M ON time 7.45, day Monday to Friday.
N OFF time 10.30, day Monday to Friday.
Fig. 2.36
M
N
Fig. 2.37
Note: when the display shows the symbol
AUTO and the boiler is switched off at the
fused spur isolation switch, the display J indicates only the OFF state. The other indications are blanked.
Reading the timed settings
Press repeatedly the button A until the display shows the symbol C1 (Fig. 2.35).
The symbols shown in Fig. 2.35 appears in
the display.
Press the “OK” button C. Each time the button is pressed the display shows the details
of the next setting.
The day display H gives a flashing indication
of the active day or group of days.
Changing or deleting the timed settings
Press repeatedly the button A until the display shows the symbol C1 Fig. 2.35).
The symbols shown in Fig. 2.35 appears in
the display.
Press the “OK” button C until the display
shows the setting to be modified or deleted.
The day display H gives a flashing indication
of the active day or group of days.
Press the button (or the buttons) G corresponding to the day (or days) for which it is
intended to apply the modification. The cor- 21 -
USE
Setting the switching time and day (or
days)
28 memory locations are available, corresponding to 14 on-off sequences.
Press repeatedly the button A until the display shows the symbol C1.
The symbols shown in Fig. 2.35 appears in
the display.
INSTRUCTIONS FOR USE
USE
responding day display stops flashing and a
new switching time can be set or deleted.
The time setting can be modified now by
pressing button D or E and the operation can
be switched on or off by pressing the button
F.
To delete a time set press the button D or E
until the symbols shown in Fig. 2.35 appears
in the time display I.
The new settings are memorised by pressing
the button A.
Manual operation
The operation of the time switch can be
forced on or off constantly or for a timed period.
To force constantly on or off the timer operation press repeatedly the button A until
the display shows the symbol TIMER. The
symbols shown in Fig. 2.38 appears on the
display.
The time delay can be set within the following ranges:
1 to 23 hours with steps of 1 hour
1 to 27 days with steps of 1 day
Press the button A until the display shows
the symbol AUTO.
The ON-OFF display J flashes indicating
that the current state of operation has been
forced.
To delete the timed delay setting, press repeatedly the button A until the display shows
the symbol TIMER, press the button D or E
until the symbols shown in Fig. 2.39 appears
in the display and then press the button A until the display shows the symbol AUTO.
Setting example shown in Fig. 2.39:
forced ON state for 4 hours.
A
A
Fig. 2.38
The operation can be switched permanently
on or off by pressing the button F and leaving
the display shows the symbol TIMER.
To force a timed delay on or off operation,
press repeatedly the button A until the display shows the symbol TIMER.
Set the time delay by pressing the button D
or E and the operation can be forced on or
off by pressing the button F.
- 22 -
Fig. 2.39
Resetting
To completely reset the timer, press the reset
button with a pointed object (pencil).
CAUTION: pushing the reset button will
completely erase the settings as well as all
the data, including the current time and day.
USEFUL ADVICE
USEFUL ADVICE
3.1
Central Heating
For reasonably economical service install a
room thermostat. Never shut off the radiator in the area where the room thermostat
is installed.
If a radiator (or a convector) does not heat
up, check that no air is present in it and that
its valve is open. If the ambient temperature
is too high, do not alter the radiator valves.
Reduce the central heating temperature instead by means of the room thermostat and
the function selector (8 in Fig. 3.1).
8
Fig. 3.1
3.2
Frost protection
This appliance is provided with a built in
anti-freeze system that operates the boiler
when the temperature is below 5 °C
Therefore, when the boiler is not lit and
used in cold weather, with consequent risk
of freezing do not switch off the boiler at
the fused spur isolation switch or close
the gas inlet cock.
3.3
Condensate drain
The condensate drain must not be modified or blocked. Blockage of the condensate
drain, caused by debris or freezing, can
cause automatic shutdown of the boiler.
If freezing is suspected and the pipe run is
accessible an attempt may be made to free
the obstruction by pouring hot water over
the exposed pipe an cleaning any blockage
from the end of the pipe.
If this fails to remedy the problem the assistance of a Gas Safe registered installer or
in IE a competent person should be sought.
3.4
Periodic maintenance
For efficient and continuous operation of
the boiler, it is advisable to arrange maintenance and cleaning by an Authorised Service Centre Engineer, at least once a year.
During the service, the most important components of the boiler will be inspected and
cleaned. This service can be part of a maintenance contract.
In particular, you are advised to have the
following checks carried out:
• primary heat exchanger;
• domestic hot water heat exchanger; burner;
• exhaust fume duct and flue;
• pressurisation of the expansion tank;
• filling up of the central heating circuit;
• bleeding of air from the central heating
system;
• general check of the appliance’s operation.
3.5
External cleaning
Before carrying out any cleaning, disconnect the appliance
from the electrical mains, using
the fused spur isolation switch
fitted adjacent to the appliance.
To clean the external panels, use a cloth
soaked in soapy water. Do not use solvents,
abrasive powders or sponges.
- 23 -
USE
3
USEFUL ADVICE
Do not carry out cleaning of the appliance
and/or its parts with readily flammable substances (for example petrol, alcohols, naphtha, etc.).
3.6
Operational faults
USE
If the lock-out signal lamp comes on
This indicates that the safety lock-out 6 (Fig.
3.2) has stopped the boiler.
To re-start the boiler, it is necessary to press
the boiler reset button 7 (Fig. 3.2).
Fig. 3.2
76
For the first lighting up and following maintenance procedures for the gas supply, it
may be necessary to repeat the resetting
operation several times so as to remove the
air present in the pipe work.
After five consecutive resetting attempts the
reset button is inhibited. To restore its function it is necessary to switch the boiler off
and on from the electrical mains, using the
fused spur isolation switch fitted adjacent to
the appliance.
Safety lock-out may occur even in case of a
blockage of the condensate drainage (e.g.
plugged drain pipe).
It is advisable to check the condensate
drainage pipe and traps for cleanness.
In this case and in case of persistent lock-out call a competent and responsible Service
Engineer.
- 24 -
If noises due to air bubbles are heard
during operation...
You should check that the pressure on the
temperature and pressure gauge (Fig. 2.2
on page 10) is not below the correct setting.
If required, top up the system correctly, as
described in the section "Refilling procedure" to page 10.
Bleed any air present in the radiators, if necessary.
If the pressure on the temperature and
pressure gauge has gone down...
It is necessary to top up the appliance with
water again, so as to raise the pressure to
an adequate level as described in the section "Refilling procedure" to page 10. If topping up with water has to be done very frequently, have the system checked for leaks.
If water comes out of the pressure relief
valve
Check on the temperature and pressure
gauge that the pressure in the central heating circuit is not close to 3 bars. In this case,
temperature rise in the circuit can cause the
pressure relief valve to open.
So that this does not happen and to decrease the pressure to a normal value, it is
advisable to vent some of the water in the
appliance through the bleed valves present
in the radiators.
If in time, a reduction in domestic hot
water supply is observed...
The likely causes may be impurities caught
in the domestic hot water flow switch filter or
limescale deposited in the domestic hot water heat exchanger. It is advisable to have
the appliance cleaned out by an Authorised
Service Centre Engineer.
USEFUL ADVICE
If water should occasionally leak from
the boiler...
Shut off the valves positioned under the
boiler (Fig. 2.11 on page 13) and call an Authorised Service Centre Engineer.
USE
If the left appliance operation light 10
(Fig. 3.3) flashes very quickly the boiler
is detecting a fault.
10
Fig. 3.3
8
In this case or in case of problems other than those mentioned here, switch off the boiler, as described in section
"Extinguishing" to page 13 and
call a competent and responsible Service Engineer.
- 25 -
TECHNICAL INFORMATION
4
TECHNICAL INFORMATION
4.1
Overview
17 18
19
20
21
22
43
42
41
INSTALLATION
40
39
38
37
36
35 34 30
Fig. 4.1
- 26 -
28
27
26 25
24
23
TECHNICAL INFORMATION
4.2
Main diagram
50
49
20
21
46
17
19
43
22 23
36
39
40
27
41
38
45 48
32
24
37
30
31
INSTALLATION
28
33
47
35
44
29
26
11
34
25
14
12
16
13
15
Fig. 4.2
11 Condensate drain pipe
12 C.h. return valve
13 D.c.w. inlet valve
14 Gas inlet valve
15 D.h.w. outlet pipe
16 C.h. flow valve
17 Fan
18 Air pressure sensor test points
19 Air pressure sensor
20 Flue temperature probe NTC
21 Condensing heat exchanger
22 Safety thermostat
23 C.h. temperature probe NTC
24 Condensate trap
- 27 -
INSTALLATION
TECHNICAL INFORMATION
25 Main circuit drain valve
26 C.h. pressure relief valve
27 Automatic air purger valve
28 Pump
29 D.h.w. flow switch
30 Modulation gas valve
31 Modulation operator
32 Gas valve outlet pressure test point
33 Gas valve inlet pressure test point
34 D.h.w. temperature probe NTC
35 Three-way diverter valve
36 D.h.w. heat exchanger
37 Primary circuit pressure switch
38 Combustion chamber over heat
39 Flame-detecting electrode
40 Ignition electrode
41 Burner
42 Combustion chamber
43 Primary heat exchanger
44 C.h. expansion tank
45 By-pass valve
46 Fan pressure connection
47 Domestic water circuit filter
48 D.h.w. flow limiter
49 Flue outlet pipe
50 Air intake pipe
- 28 -
TECHNICAL INFORMATION
Hydraulic specifications
The hydraulic specifications in Fig. 4.3 represent the pressure (available head for the
central heating system) as a function of the
flow rate.
The load loss due to the boiler has already
been subtracted.
kPa bar
60 0.6
50 0.5
40 0.4
4.4
Expansion vessel
Note: this boiler is designed for operation only in a sealed central heating system.
The height difference between the pressure
relief valve and the highest point in the system may be 10 m at most.
For greater differences, increase the preload pressure in the expansion vessel and
the system, when cold, by 0.1 bar for each
additional 1 m.
Capacity
30 0.3
20 0.2
Pre-load pressure
10 0.1
0 0.0
0
Fig. 4.3
200
400
600
800
1000
1200
1400
l/h
Output with thermostat cocks shut off
The boiler is equipped with an automatic bypass valve (45on page 28), which protects
the condensing primary exchanger.
In case of excessive reduction or total
blockage of water circulation in the central heating system owing to closure of the
thermostatic valves or system component
cocks, the by-pass valve ensures a minimum flow of water through the primary heat
exchanger.
Maximum volume of water in the
system *
l
8,0
kPa
100
bar
1,0
l
124
Fig. 4.4
* Where conditions are:
• Average maximum temperature of the
system is 85 °C
• Initial temperature when filling up the system is 10 °C
For systems with volumes
greater than 124l, an additional
expansion vessel must be provided.
- 29 -
INSTALLATION
4.3
TECHNICAL INFORMATION
4.5
Technical data mod. Riva Plus
HE 24C ERP
Heat input
Nominal net (A) (ch - dhw)
Nominal gross (B) (ch - dhw)
Minimun net (A) ch - dhw
Minimun gross (B) ch - dhw
Domestic hot water
kW
25,0
BTU/h 85304
kW
27,8
BTU/h 94687
kW
7,5
Min/Max temperature settings
Maximum pressure
Minimum pressure
°C
35 - 55
kPa
1000
bar
10
kPa
30
bar
0,3
BTU/h 25591
Flow rate minimun
l/min
2,5
kW
Flow rate 30° rise (D)
l/min
11,6
Flow rate 35° rise (D)
l/min
10,0
Flow rate 40° rise (D)
l/min
8,7
8,3
BTU/h 28406
Useful output
Maximun (ch - dhw)
INSTALLATION
Minimun (ch - dhw)
Maximun condensing (ch - dhw)
Minimun condensing (ch - dhw)
kW
24,4
BTU/h 83256
kW
Minimum return temperature
Maximum pressure
Minimum pressure
Available head (in 1000 l/h)
BTU/h 89739
kW
7,8
Propane G31
°C
50-85
°C
40
kPa
250
bar
2,5
kPa
30
bar
0,3
kPa
25
bar
0,25
%
88,0
Seasonal effciency G30 G31 (C)
%
89,0
- 30 -
Butane G30
BTU/h 26615
Seasonal efficiency G20
* to the minimum useful output
Natural G20
26,3
Central heating
Min/Max flow temperature settings*
Gas
7,3
BTU/h 24909
kW
Gas supply pressures
Pa
mbar
Nom
2000
20
Min
1700
17
Max
2500
25
Nom
2900
29
Min
2000
20
Max
3500
35
Nom
3700
37
Min
2500
25
Max
4500
45
1 mbar approximately equals 10 mm H2O
TECHNICAL INFORMATION
Gas restrictors references
N°
Ø mm
/100
Natural G20
12
120
Butane G30
12
77
Propane G31
12
77
Voltage
V~
230
140
Frequency
Hz
50
1,4
Nominal Power consumption
W
79
Pa
280
Minimum Power consumption
W
65
mbar
2,8
Stand-by Power consumption
W
Pa
350
Protection degree
mbar
3,5
External fuse rating
Natural G20
Butane G30
Propane G31
Pa
1340
mbar
13,4
Pa
2760
mbar
27,6
Pa
3550
mbar
35,5
Min. gas pressures at the burner
Natural G20
Butane G30
Propane G31
Pa
mbar
Ignition gas pressures at the burner
Natural G20
Electrical data
Internal fuse rating
Pa
mbar
A
3
A
N° 2 - 2
AF
850
8,5
3
IPX4D
Pa
2110
Flue design
mbar
21,1
Boiler type
Pa
2700
C12 C32 C42 C52 C82
mbar
27,0
ø Coaxial
mm
60/100
1 mbar approximately equals 10 mm H2O
ø Twin split pipes
mm
80/80
ø Roof
mm
80/125
Gas rate maximum - ch dhw
Nominal heat flow rate (A) (E)
kW
25,0
60,0
Butane G30
Propane G31
Natural G20
m3/h
2,65
Exhaust temperature (E)
°C
Butane G30
kg/h
1,97
Mass flow rate
kg/s
0,0128
Propane G31
kg/h
1,94
Natural G20
m3/h
0,79
Nominal heat input (A) (E)
kW
25,0
Butane G30
kg/h
0,59
CO2 content with gas G20
%
7,9
Propane G31
kg/h
0,58
O2 content with gas G20
%
6,8
Gas rate minimum - ch dhw
(E)
Flue gas figures
CO content with gas G20
ppm
52,0
Exhaust temperature (E)
°C
60,0
NOx class
Weighted NOx
2
ppm
94
- 31 -
INSTALLATION
Max. gas pressures at the burner
TECHNICAL INFORMATION
CO2 contents - ch dhw
Nominal heat input (A) (E)
kW
25,0
CO2 content with gas G20
%
7,9
CO2 content with gas G30 G31
%
9,1
Minimum heat input (A) (E)
kW
7,5
CO2 content with gas G20
%
3,9
CO2 content with gas G30 G31
%
4,5
Height
mm
803
Width
mm
400
Depth
mm
350
Weight (dry)
kg
36,8
Water volume in the boiler (up to 1
bar)
l (kg)
1,4
Other specifications
referred to the net calorific value at 15°C and
1013,25 mbar: G20 = 34,02 MJ/m3 - G31 = 46,34 MJ/
kg
INSTALLATION
(A)
referred to the gross calorific value at 15°C and
1013,25 mbar: G20 = 37,78 MJ/m3 - G31 = 50,37 MJ/
kg
(B)
The value is used in the UK Government's Standard
Assessment Procedure (SAP) for energy rating of
dwellings. The test data from which it has been calculated have been certified by a notified body.
(C)
(D)
Values subject to tolerance
Values refer tests with a 1 m flue working at the
nominal heat input
(E)
- 32 -
TECHNICAL INFORMATION
Riva Plus HE 24C ERP
Model(s):
Condensing boiler:
Yes
Low-temperature boiler (**):
No
B1 boiler:
No
Cogeneration space heater:
No
If yes, equipped with a supplementary heater:
Combination heater:
Rated heat output
Symbol Value
P rated
25
Unit
Item
kW
Seasonal space heating
energy efficiency
Symbol
Value
Unit
ηs
89
%
For boiler space heaters and boiler combination heaters: Useful heat output
For boiler space heaters and boiler combination heaters:
Useful efficiency
At rated heat output and
high-temperature regime (*)
P4
24,4
kW
At rated heat output and
high-temperature regime (*)
η4
87,7
%
At 30% of rated heat output
and low-temperature regime
(**)
P1
7,9
kW
At 30% of rated heat output
and low-temperature regime
(**)
η1
95,4
%
Auxiliary electricity consumption
At full load
At part load
In standby mode
Other items
elmax
0,079
kW
Standby heat loss
Pstby
0,098
kW
Ignition burner power consumption
Pign
-
kW
elmin
0,065
kW
PSB
0,003
kW
Annual energy consumption
QHE
78,685
GJ
Sound power level, indoors
LWA
48
dB
Emission of nitrogen oxides
NOx
166
mg/
kWh
Water heating energy efficiency
ηwh
86
%
For combination heaters:
Declared load profile
XL
Daily electricity consumption
Qelec
0,132
kWh
Daily fuel consumption
Qfuel
22,756
kWh
Annual electricity consumption
AEC
29
kWh
Annual fuel consumption
AFC
17
GJ
Contact details
See manual cover
(*) High-temperature regime means 60°C return temperature at heater inlet and 80°C feed temperature at heater
outlet.
(**) Low temperature means for condensing boilers 30°C, for low-temperature boilers 37°C and for other heaters
50°C return temperature (at heater inlet).
- 33 -
INSTALLATION
Item
Yes
TECHNICAL INFORMATION
4.6
Technical data mod. Riva Plus
HE 28C ERP
Heat input
Nominal net (A) (ch - dhw)
Nominal gross (B) (ch - dhw)
Minimun net (A) ch - dhw
Minimun gross (B) ch - dhw
Domestic hot water
kW
29,0
BTU/h 98952
kW
32,2
BTU/h 109837
kW
8,7
Min/Max temperature settings
Maximum pressure
Minimum pressure
°C
35 - 55
kPa
1000
bar
10
kPa
30
bar
0,3
BTU/h 29686
Flow rate minimun
l/min
2,5
kW
Flow rate 30° rise (D)
l/min
13,6
Flow rate 35° rise (D)
l/min
11,6
Flow rate 40° rise (D)
l/min
10,2
Pa
mbar
9,7
BTU/h 32951
Useful output
Maximun (ch - dhw)
INSTALLATION
Minimun (ch - dhw)
Maximun condensing (ch - dhw)
Minimun condensing (ch - dhw)
kW
28,3
BTU/h 96564
kW
BTU/h 104411
kW
9,1
Propane G31
°C
50-85
Minimum return temperature
°C
40
kPa
250
bar
2,5
Available head (in 1000 l/h)
kPa
30
bar
0,3
kPa
25
bar
0,25
Seasonal efficiency G20
%
88,0
Seasonal effciency G30 G31 (C)
%
89,0
* to the minimum useful output
- 34 -
Butane G30
BTU/h 31050
Min/Max flow temperature settings*
Minimum pressure
Natural G20
30,6
Central heating
Maximum pressure
Gas
8,4
BTU/h 28662
kW
Gas supply pressures
Nom
2000
20
Min
1700
17
Max
2500
25
Nom
2900
29
Min
2000
20
Max
3500
35
Nom
3700
37
Min
2500
25
Max
4500
45
1 mbar approximately equals 10 mm H2O
TECHNICAL INFORMATION
Natural G20
Butane G30
Propane G31
Gas restrictors references
N°
Ø mm
/100
Natural G20
14
120
Butane G30
14
77
Propane G31
14
77
Voltage
V~
230
140
Frequency
Hz
50
1,4
Nominal Power consumption
W
90
Pa
260
Minimum Power consumption
W
75
mbar
2,6
Stand-by Power consumption
W
Pa
350
Protection degree
mbar
3,5
External fuse rating
Pa
1330
mbar
13,3
Pa
2780
mbar
27,8
Pa
3550
mbar
35,5
Min. gas pressures at the burner
Natural G20
Butane G30
Propane G31
Pa
mbar
Ignition gas pressures at the burner
Natural G20
Electrical data
Internal fuse rating
Pa
mbar
3
IPX4D
A
3
A
N° 2 - 2
AF
850
8,5
Pa
2110
Flue design
mbar
21,1
Boiler type
Pa
2700
C12 C32 C42 C52 C82
mbar
27,0
ø Coaxial
mm
60/100
1 mbar approximately equals 10 mm H2O
ø Twin split pipes
mm
80/80
ø Roof
mm
80/125
Gas rate maximum - ch dhw
Nominal heat flow rate (A) (E)
kW
29,0
Butane G30
Propane G31
Natural G20
m3/h
3,07
Exhaust temperature (E)
°C
60,0
Butane G30
kg/h
2,29
Mass flow rate
kg/s
0,01
Propane G31
kg/h
2,25
Natural G20
m3/h
0,92
Nominal heat input (A) (E)
kW
29,0
Butane G30
kg/h
0,69
CO2 content with gas G20
%
7,9
Propane G31
kg/h
0,68
O2 content with gas G20
%
6,8
Gas rate minimum - ch dhw
(E)
Flue gas figures
CO content with gas G20
ppm
53,0
Exhaust temperature (E)
°C
60,0
NOx class
Weighted NOx
2,0
ppm
90
- 35 -
INSTALLATION
Max. gas pressures at the burner
TECHNICAL INFORMATION
CO2 contents - ch dhw
Nominal heat input (A) (E)
kW
29,0
CO2 content with gas G20
%
7,9
CO2 content with gas G30 G31
%
9,1
Minimum heat input (A) (E)
kW
8,7
CO2 content with gas G20
%
3,9
CO2 content with gas G30 G31
%
4,3
Height
mm
803
Width
mm
400
Depth
mm
350
Weight (dry)
kg
37,7
Water volume in the boiler (up to 1
bar)
l (kg)
1,5
Other specifications
referred to the net calorific value at 15°C and
1013,25 mbar: G20 = 34,02 MJ/m3 - G31 = 46,34 MJ/
kg
INSTALLATION
(A)
referred to the gross calorific value at 15°C and
1013,25 mbar: G20 = 37,78 MJ/m3 - G31 = 50,37 MJ/
kg
(B)
The value is used in the UK Government's Standard
Assessment Procedure (SAP) for energy rating of
dwellings. The test data from which it has been calculated have been certified by a notified body.
(C)
(D)
Values subject to tolerance
Values refer tests with a 1 m flue working at the
nominal heat input
(E)
- 36 -
TECHNICAL INFORMATION
Riva Plus HE 28C ERP
Model(s):
Condensing boiler:
Yes
Low-temperature boiler (**):
No
B1 boiler:
No
Cogeneration space heater:
No
If yes, equipped with a supplementary heater:
Combination heater:
Rated heat output
Symbol Value
P rated
29
Unit
Item
kW
Seasonal space heating
energy efficiency
Symbol
Value
Unit
ηs
89
%
For boiler space heaters and boiler combination heaters: Useful heat output
For boiler space heaters and boiler combination heaters:
Useful efficiency
At rated heat output and
high-temperature regime (*)
P4
28,3
kW
At rated heat output and
high-temperature regime (*)
η4
88,0
%
At 30% of rated heat output
and low-temperature regime
(**)
P1
9,2
kW
At 30% of rated heat output
and low-temperature regime
(**)
η1
95,2
%
Auxiliary electricity consumption
At full load
At part load
In standby mode
Other items
elmax
0,090
kW
Standby heat loss
Pstby
0,113
kW
Ignition burner power consumption
Pign
-
kW
elmin
0,075
kW
PSB
0,003
kW
Annual energy consumption
QHE
91,354
GJ
Sound power level, indoors
LWA
49
dB
Emission of nitrogen oxides
NOx
158
mg/
kWh
Water heating energy efficiency
ηwh
86
%
For combination heaters:
Declared load profile
XL
Daily electricity consumption
Qelec
0,138
kWh
Daily fuel consumption
Qfuel
22,586
kWh
Annual electricity consumption
AEC
30
kWh
Annual fuel consumption
AFC
17
GJ
Contact details
See manual cover
(*) High-temperature regime means 60°C return temperature at heater inlet and 80°C feed temperature at heater
outlet.
(**) Low temperature means for condensing boilers 30°C, for low-temperature boilers 37°C and for other heaters
50°C return temperature (at heater inlet).
- 37 -
INSTALLATION
Item
Yes
GENERAL REQUIREMENTS
INSTALLATION
5
GENERAL REQUIREMENTS
Benchmark places responsibilities on both
manufacturers and installers. The purpose is
to ensure that customers are provided with
the correct equipment for their needs, that it
is installed, commissioned and serviced in
accordance with the manufacturer’s instructions by competent persons and that it meets
the requirements of the appropriate Building
Regulations. The Benchmark Checklist can
be used to demonstrate compliance with
Building Regulations and should be provided to the customer for future reference.
Installers are required to carry out installation, commissioning and servicing work in
accordance with the Benchmark Code of
Practice which is available from the Heating
and Hotwater Industry Council who manage
and promote the Scheme. Visit www.centralheating.co.uk for more information.
Our Company supports the Benchmark initiative. The Benchmark Checklist is located
at the back of this manual and should be
completed by the Installing/Commissioning
Engineer and handed over to the User for
future reference by other visiting Engineers.
Also included is the Service Interval Record
card that should be completed by the Service Engineer following the annual service
maintenance of the boiler and system.
For Ireland (IE), it is necessary to complete a
“Declaration of Conformity” to indicate compliance to I.S.813.2002.
This appliance must be installed by a competent person in accordance with the Gas
Safety (installation & Use) Regulations.
5.1
Related documents
The installation of this appliance must be in ac- 38 -
cordance with the relevant requirements of the
current Gas Safe (Installation & Use) Regulations, the Local Building Regulations, the current I.E.E. Wiring Regulations, the Regulations
and by-laws of the local water undertaking,
and in Scotland, in accordance with the Building Standards (Scotland) Regulation. Health
and safety document n° 635 ”Electricity at work
regs.”.
It should also be in accordance with the British
Standard Codes of Practice:
In Ireland (IE). The installation must be carried
out by a Competent Person and installed in accordance with the current edition of I.S.813.2002
“Domestic Gas Installations” the current Building
Regulations and reference should be made to
the current ETCI rules for electrical installations.
5.2
Location of appliance
The appliance may be installed in any room or
internal space, although particular attention is
drawn to the requirements of the current I.E.E.
Wiring Regulations, and in Scotland, the electrical provisions of the Building Regulations applicable in Scotland, with respect to the installation
of the combined appliance in a room containing
a bath or shower.
For Ireland (IE), reference should be made to
the current edition of I.S.813.2002 and the current ETCI rules for electrical installations.
Where a room-sealed appliance is installed
in a room containing a bath or shower, any
electrical switch or appliance control, utilising mains electricity should be so situated
that it cannot be touched by a person using
the bath or shower.
The location must permit the provision of an adequate flue and termination.
For unusual locations special procedures may
be necessary and BS 6798 gives detailed guidance on this aspect.
A compartment used to enclose the appliance
must be designed specifically for this purpose.
This appliance is not suitable for external installation.
5.3
Flue system
The provision for satisfactory flue termination
must be made as described in BS 5440 part 1.
For Ireland (IE), refer to I.S.813.2002.
The appliance must be installed so that the flue
terminal is exposed to external air.
It must not be installed so that the terminal
discharges into an other room or space as an
outhouse or lean-to. It is important that the position of the terminal allows a free passage of air
across at all times.
The terminal should be located with due regard
for the damage or discoloration that might occur
to building products in the vicinity.
In cold and/or humid weather water vapour may
condense on leaving the flue terminal; the effect
of such ”steaming” must be considered.
Pluming may easily occur at the terminal. Where
possible, terminal position which could cause a
nuisance should be avoided.
The minimum acceptable spacing from the terminal to obstructions and ventilation openings
are specified in Fig. 5.1.
JK
G E
I
O
BC
L
F
D
I
A
Q
I
P I
H
N M
I
C
D
E
F
G
H
I
J
K
L
M
N
O
O
P
Q
Below eaves
200
Below balconies*
600
Below car port roof
NO
From vertical drain pipes and soil
pipes
150
From internal corners**
450
From external corners
300
Above ground or balcony level***
300
From a wall or surface
600
From a terminal facing a terminal
2500
From an opening in the car port
(e.g. door, window) into dwelling
NO
Vertically from a terminal in the
same wall
1500
Horizontally from a terminal in the
same wall
300
Above the roof pitch with roof slope
less than or equal to 30°
350
Above the roof pitch with roof slope
more than 30°
600
From wall face
600
From, above or to side of an opening
300
* Wherever practicable to do so, the flue
should be extended beyond the perimeter of
the balcony
** Consideration should be given to adding
protection against condensate to the adjacent structure
*** Wall terminals with horizontal discharge less
than 2.5 m from a car parking space and less
than 2,1 m above the ground.
Wall terminals less than 2,1 m above the
ground with horizontal discharge of the flue
products across a public footway, or a frequently used private access route, or a patio
(hard surface area).
Fig. 5.1
Terminal position
A Directly below the window or other
opening
B Below gutters, soil pipes or drain
pipes
mm
300
75
5.4
Gas supply
The Gas meter is connected to the service pipe
by the local gas region or a local gas region contractor.
If the gas supply for the boiler serves other appliances ensure that an adequate supply is avail- 39 -
INSTALLATION
GENERAL REQUIREMENTS
GENERAL REQUIREMENTS
5.5
Air supply
The room in which the boiler is installed does
not require a purpose provided air vent.
INSTALLATION
5.6
To avoid condensate being trapped:
• the drain pipe should be run with a fall of at
least 2.5° (45 mm/m) away from the boiler;
• the number of bends and joints should be kept
at minimum.
The drain pipe should be adequately fixed to
prevent pipe sagging.
If a part of the drainpipe runs externally this part
should be kept as short as possible and protected to reduce the risk of freezing.
Connection of condensate drainage pipe to
internal soil and vent stack.
A
Condensate
drain
Ventilation
If installed in a cupboard or compartment, it is
not necessary to provide additional ventilation
for cooling for this particular product. However
consideration must be given to clearance requirements for maintenance (section "Precautions for installation" to page 43) and under no
circumstances must stored articles be allowed
to come into contact with the boiler or flue pipe.
B
C
Condensate drain
Ensure that the condensate discharge complies
with the national or local regulations in force.
The condensate pipe must be fitted in accordance with Building Regulations.
Drain pipe material should be resistant to acid
as the condensate is slightly acid with a pH less
than 6.5. The boiler includes a trap (24on page
27) that prevents the combustion products entering the drain.
The boilers incorporate a condensate trap with a
75 mm seal to comply with BS 6798: 2008.
The schematic diagrams of possible connections are given in Fig. 5.2 and Fig. 5.3. The
length of the condensate pipe should be kept
to a minimum, any external pipe should not be
more than 3 m in 32 mm pipe and insulated to
prevent freezing.
ABoiler
B Internal soil and vent stack
C Invert
D 450 mm up to three storeys
Connection of condensate drainage pipe
downstream of a sink waste trap
A
Condensate
drain
E
F
Fig. 5.3
- 40 -
D
Dimensions in mm
Fig. 5.2
5.7
450
able both to the boiler and the other appliance
when they are in use at the same time.
Pipework must be of adequate size. Pipes of
a smaller size than the boiler inlet connection
should not be used.
Installation pipes should be fitted in accordance with BS 6891 and the complete installation
should be tested for tightness.
For Ireland (IE), refer to I.S.813.2002.
Dimensions in mm
GENERAL REQUIREMENTS
5.8
Water circulation (c.h.)
Detailed recommendations are given in BS
6798, BSEN 12828: 2003, BSEN 12831: 2003
& BSEN 14446: 2004; the following notes are
given for general guidance.
For Ireland (IE), refer to I.S.813.2002.
Pipework
The return temperature must not be lower of
40°C. Copper tubing to BSEN 1057 is recommended for water pipes. Jointing should be either with capillary soldered or with compression
fittings.
Where possible pipes should have a gradient
to ensure air is carried naturally to air release
points and water flows naturally to drain taps.
The appliance has a built-in automatic air release valve, it should be ensured as far as possible that the appliance heat exchanger is not a
natural collecting point for air.
Except where providing useful heat, pipes
should be insulated to prevent heat loss and to
avoid freezing.
Particular attention should be paid to pipes
passing through ventilated spaces in roofs and
under floors.
By-pass
The appliance includes an automatic by-pass
valve which protects the main heat exchanger in
case of reduced or interrupted water circulation
through the heating system due to the closing
of thermostatic valves or cock-type valves within
the system.
The by-pass is calibrated to assure a minimum
flow of 200-300 lts/hr through the main heat exchanger.
If you are installing a system that includes thermostatic radiator valves (TRV) and/or small bore
(8-10 mm) it may be necessary to fit an external by-pass to facilitate correct operation of the
boiler.
The fitting of an external bypass helps to prevent and limit system noise.
Air release points
These must be fitted a tall high points where air
will natural collect and must be sited to facilitate
complete filling of the system.
Expansion vessel
The appliance has an integral sealed expansion
vessel to accommodate the increase of water
volume when the system is heated. Refer to Fig.
4.4 on page 29 for its technical data.
If the heating circuit has an unusually high water
content, calculate the total expansion and add
an additional sealed expansion vessel with adequate capacity.
Mains water feed: central heating
There must be no direct connection to the mains
water supply even through a non return valve,
without the approval of the Local Water Authority.
Mains water feed: hot water supply
The domestic section of the boiler is designed to
withstand an internal domestic water pressure
of 10 bar. Where it is likely that the mains domestic water pressure may exceed 5 bar, it is
possible due to internal “water hammer” effects
that the pressure within the domestic system
can increase to a level in excess of the 10 bar
limit.
In these circumstances it is therefore recommended that a 3 bar pressure reducing valve be
fitted to the incoming mains water supply and a
mini expansion vessel installed on the domestic
circuit.
These devices will protect the boiler and the domestic system from damage due to excessive
domestic water pressure.
- 41 -
INSTALLATION
ABoiler
E Sink
F Open end of condensate drainage pipe direct into gully below grating but above water
level
GENERAL REQUIREMENTS
Filling
A method for initially filling the system and replacing water lost during servicing must be provided and it must comply with local water authority regulations.
The correct method is shown in Fig. 5.4.
The temporary connection must be removed immediately after filling.
Control valve
Double check valve
Temporary
connection
Supply pipe
(cold water inlet)
C.h. return pipe
Fig. 5.4
Control valve
INSTALLATION
The installer should ensure that no leaks exist
either inside the boiler or on the system as frequent filling of the system could cause premature scaling of the heat exchanger.
5.9
Domestic water
The domestic water installation must be in accordance with the relevant recommendations
of BS 5546. Copper tubing to BS EN 1057 is
recommended for water carrying pipework and
must be use for pipework carrying potable water.
For Ireland (IE), refer to I.S.813.2002.
5.10 Water treatment
C.h. circuit
Where a new boiler is fitted to a new system with
either plastic or copper pipes, it is important the
system is fully flushed, on completion, to ensure
flux residues, swarfs, oils and other installation
debris is removed.
Where a new boiler is fitted to an existing system, it is important the debris from the existing
system is fully removed in order to ensure the
efficiency of the new appliance is maintained.
Details on flushing procedure are given in the
section "Initial filling of the system" to page 51
- 42 -
of this manual.
D.h.w. circuit (scale protection)
In areas where the water is ’hard’ (i.e. more than
200 ppm total hardness as defined by BS 7593:
2006 Table 2) it is recommended that a proprietary scale-reducing device is fitted into the boiler
cold supply, within the requirements of the local
water company.
5.11 Electrical supply
Warning, this appliance must be earthed
External wiring to the appliance must be carried
out by a competent person and be in accordance with the current I.E.E. Regulations and any
local regulations which apply.
Reference should be made to the current ETCI
rules for electrical installations.
For Ireland (IE), refer to I.S.813.2002.
The boiler is supplied for connection to a 230 V~
50 Hz supply. The supply must be fused at 3A.
The method of connection to the electricity supply must facilitate complete electrical isolation of
the appliance by the use of a fused spur isolation switch. Its installation permits a complete
switching off in the conditions of the overvoltage
category III. Alternatively it can be used a 3A
fused three pin plug and unswitched shuttered
socket outlet both complying with BS 1363.
The point of connection to the electricity supply must be readily accessible and adjacent to
the appliance, except where the appliance is
installed in a bathroom, this must then be sited
outside the bathroom.
INSTALLATION
6.1
INSTALLATION
6.2
Warnings
The use of gas appliances is
subject to statutory control; it is
essential to observe the current
regulations and laws in force
(see also chapter 5).
The appliance must discharge
combustion products directly
outside or into a suitable exhaust duct designed for this purpose. Combustion products
must be discharged using original flue kits only, since they are
integral parts of the boiler.
Refer to section "Electrical connections" to
page 48 in this chapter for the electrical connections.
In no circumstances will the manufacturer be held responsible if the warnings
and instructions contained in this manual have not been complied with.
The following prescriptions
must be respected for installation:
• The boiler must be fixed to a strong wall.
• The dimensions for the exhaust fume duct
(detailed in section "Choice of flue" to
page 46) and the correct procedures for
installing the duct, depicted in the instruction leaflet included with the flue kit, must
be complied with during installation.
• To allow maintenance procedures it is
necessary to leave the minimum gaps indicated in Fig. 6.1.
For LPG, the appliance must also conform
with the requirements of the distributors and
comply with current Regulations and laws in
force.
The safety relief valve and the condensate
drain must be connected to a suitable drain,
or discharge in a safe manner.
The electrical wiring must conform with current Regulations, in particular:
• The boiler must be earthed using the correct bonding clamp.
• Adjacent to the boiler a fused spur isolation switch must be installed which permits
a complete switching off in the conditions
of the overvoltage category III.
Precautions for installation
250
50
25
INSTALLATION
6
200
Fig. 6.1
All measures are in mm
• When installing the boiler in a cupboard,
cover or alcove allow at least 50 mm permanent clearance from the front face of
the boiler. Also ensure sufficient clearance
to allow free access for servicing and the
lowering of the front control panel.
- 43 -
INSTALLATION
198
196
245
ø100
73
47
200
400
31
A
B
C
50
115
142
35
16
Boiler front
100
D
F
257
140
60
It is advisable to equip the system with a
sediment filter, or use a water-treatment
product in the circulating water.
The latter option in particular, not only
cleans out the system, but also has an anticorrosive effect by promoting formation of a
protective skin on metal surfaces and neutralising gases present in the water.
We recommend the use of a suitable universal inhibitor to protect the c.h. system from
corrosion.
Overall dimensions
The boiler respects the following dimensions:
B
C
ø80
ø80
A
6.3
Installing the bracket
Precautions
Before mounting the bracket, check that the
dimensions for fitting the exhaust fume duct
are complied with (refer to the leaflet included with the flue kit, packed separately).
Utilise the paper template supplied with the
boiler to determine the fixing position for
the bracket and boiler. Securely mount the
bracket to the wall using appropriate fixings
suitable for the type of wall construction and
capable of supporting the total (wet) load.
Refer to the weight given in the technical
data tables specific for each model.
- 44 -
F G H
60
INSTALLATION
• Before installing the boiler on an existing
c.h. system, flush it out thoroughly before
fitting the boiler, so as to remove muddy
deposits.
6.4
803
700
• If the boiler is installed outside, cover the
appliance to protect it against the elements and add some special anti-freeze
(neutralised) to the c.h. system.
E
Fig. 6.2
A
B
C
D
E
F
G
H
I
J
65
52
64
130
I
65
200
J-E
G-H
350
J
Flue outlet / air intake pipe (co-axial)
Flue outlet pipe ø 80 mm (twin kit)
Air intake pipe ø 80 mm (twin kit)
Electric connections area
C.h. flow
D.h.w. outlet
Gas
D.c.w. inlet
C.h. return
Condensate drain connection area
INSTALLATION
Joints
Functions
Gas, c.h. return, c.h. flow
D.c.w. inlet
D.h.w. outlet
Pressure relief valve
Condensate drain
sizes in mm o.d.
6.6
Pipe sizes
(o.d)
ø 22
ø 15
ø 15
ø 15
ø 25 (plastic)
charge pipework.
• Fit the condensate drain 11 (Fig. 6.4) in the
air brake connected to the drainage pipework. See also section "Condensate drain"
to page 40.
Mounting the boiler
• Take the protective caps off the boiler
pipework.
• Thoroughly clean the connections.
• Mount the boiler on its bracket.
• Fix the c.h. valves A and gas cock B (¾”) to
the boiler using the ¾” gaskets (Fig. 6.3).
• Fix the ø 22 mm pipes C (c.h. circuit) to the
c.h. valves A and the ø 22 mm pipe D (gas)
to the cock B using the ¾” gaskets.
• Repeat the above procedure for the d.c.w.
inlet utilising the ½” cold water inlet valve
J, the ø 15 mm copper tail E with its connection nut and two ½” gaskets.
• Fix the ø 15 mm copper tail F with the ½”
connection nut and a ½” gasket.
C
F
G
11
Fig. 6.4
6.7
Fitting the flue system
Refer to the assembly instructions contained
within the chosen flue kit packaging for the
correct assembly and installation.
In general, it has to be taken in consideration that the horizontal sections of the flue
pipe must have an horizontal sloping not
less than 1.5 deg. (25 mm per metre) towards the boiler.
In the standard horizontal flue kit the flue
pipe is angled within the air duct therefore
the air duct must be horizontally installed.
D
E
C
A
B
J
Fig. 6.3
A
• Connect the pipe G (Fig. 6.4) from the
pressure relief valve to the safety dis-
Fig. 6.5
If one or more extensions have to be used
they must be adequately supported so that
- 45 -
INSTALLATION
6.5
INSTALLATION
there is no sag in the flue pipe and a minimum fall of 1,5 deg. (25 mm per metre) over
the whole length towards the boiler is ensured.
Before fitting the flue system, ensure that
the flue gasket shown in Fig. 6.5 (given with
the boiler) is fitted to the boiler.
6.8
Choice of flue
The following flue kits are available for connecting to the boiler:
Standard horizontal flue kit (Fig. 6.6 A)
Type C13
INSTALLATION
B
Vertical kit with 90° elbow (Fig. 6.6 B)
Co-axial 60/100 mm.
Supplied with a straight flanged adapter a
co-axial elbow and a co-axial pipe with terminal, this kit allows for a vertical rise of 0,5
m from the boiler. In all circumstances the
flue terminal must discharge horizontally
and the equivalent flue length must not exceed 2,7 metres.
Elbows 45° & 90° (Fig. 6.6 C)
Coaxial 60/100 mm.
Elbow kits enable the standard flue kits to be
offset to overcome obstructions or ensure
the correct clearances for the flue terminal.
Each elbow used in addition to the standard
flanged elbow reduces the overall acceptable length of the flue system as follows:
For the elbow of 45° loss
0,5 m
For the elbow of 90° loss
1m
Twin pipe kits ø 80 mm (Fig. 6.7 - Fig. 6.8)
C
A
90°
Type C12
45°
Fig. 6.6
Co-axial 60/100 mm - nominal length 1 m
This kit can be fitted to allow discharge to
the rear or either side of the boiler via the
flanged boiler adapter elbow. Minimum
length required is 0.3 m. Maximum equivalent length of 2,5 metres can be achieved
utilising extensions. This flue system can
only be used to discharge horizontally, it is
not designed to enable termination in the
vertical plane.
- 46 -
Fig. 6.7
Various twin (split) pipes kits and optional
accessories (elbows) are available to assist
in the termination of the flue where the boiler
is installed in a location remote to an outside
wall.
These kits allow for separation of the air
INSTALLATION
supply pipe from the pipe that discharges
the exhaust gasses. Consequently it is possible to extend the flue system to a greater
distance than that provided by the standard
horizontal co-axial flue.
If either an additional 45° or 90° accessory
elbow is used then the maximum permissible length of either pipe must be reduced by
0.90 m or 1,65 m respectively.
Two restrictors with different size are
supplied with the twin pipe kit and have
to be installed between the boiler and the
air intake adapter (Fig. 6.9).
Air intake adapter
Restrictor
Gasket
Type C42
45° =--- 0,90 m
Type C52
Type C82
Fig. 6.8
N.B: The air intake and the flue outlet
must not terminate on opposite sides of
the building.
Fig. 6.9
For the correct use of the restrictors with
twin pipes refer to the table:.
Equivalent length
(air duct + flue duct)
Restrictor
Between 1 and 15 m
ø 50 mm
More than 15 m up to 30 m
ø 55 mm
Vertical- roof kit (Fig. 6.10)
This kit allows vertical termination of the
flue pipe through the roof. The kit is 1.2 min
length. Extension pieces (Co-axial) are also
available which allows the flue system to be
extended to a total overall maximum permissible length.
Optional 45° and 90° elbow scan be used to
offset the flue route. Each additional elbow
reduces the overall acceptable length of the
flue system as follows:
For the elbow of 45° loss
0,5 m
For the elbow of 90° loss
1m
- 47 -
INSTALLATION
90° =--- 1,65 m
INSTALLATION
dimensions of the ducts “a” and “b” of Fig.
6.11.
Type C32
”a” vertical length (m)
90° =--- 1 m
2.4
2.2
2.0
1.8
max =8,5 m
ø 125
1.6
45° =--- 0,5 m
1.4
1.2
1.0
0.8
Fig. 6.10
Allowed values
0.6
0.4
INSTALLATION
Pluming kit (Fig. 6.11) (Fig. 6.11)
Co-axial ø 60/100 mm + vertical part ø 60
mm (flue outlet).
This kit allows the combustion air to be
sucked up and expel the burnt gases directly
to the outside through a telescopic co- axial
flue (450-950 mm).
Type C52
90° =--- 0,85 m
0.2
0.0
0.4
0.6
Fig. 6.12
0.8
1.0
1.2
1.4
1.6
1.8
”b” horizontal length (m)
Each additional elbow reduces the overall
acceptable length of the flue system as follows:
45° (60/100 mm) reduce length by 0,5 m.
90° (60/100 mm) reduce length by 1 m.
45° (60 mm) reduce length by 0,65 m.
90° (60 mm) reduce length by 0,85 m.
ø 60 mm
45° =--- 0,65 m
90° =--- 1 m
ø 60/100 mm
45° =--- 0,5 m
Fig. 6.11
In the last section, the fumes are expelled
through a vertical section.
Extensions and elbows can be added to extend the kit’s length.
The chart of Fig. 6.12 gives the allowable
- 48 -
6.9
Electrical connections
• Remove the front panel of the case (see
the section 9.2 in this manual).
• Remove the screws K (Fig. 6.13).
• Loosen the screws L.
INSTALLATION
M
K
• Remove the side panels or move the lower part of the side panels as indicated in
Fig. 6.14 and pull the control panel. When
completely pulled out, the panel can rotate
45° downwards to facilitate the operations
on the internal parts.
Fig. 6.14
• Loosen the screws M and remove the service panel (Fig. 6.15).
Fig. 6.15
For the electrical connection to the boiler
use electric wire switch conform to the current regulations, with flexible cord, each
core having a cross section area not less
than 0,75 mm2.
• Connect the electrical supply flexible
cord coming from the fused spur isolation
switch to the power supply terminal block
of the boiler (Fig. 6.16) keeping the same
connections for the live (brown wire) and
the neutral (blue wire). External 3 A fuse or
fused plug with same current rating is recommended. Do not connect live wires to
terminals to which the room thermostat
must be connected.
• Connect the earth wire (yellow/green).
Connection of a room thermostat
The room thermostat must be connected to
the terminal block situated next to the control panel.
When connecting any type of external
control, the link N in Fig. 6.16 must be
removed.
- 49 -
INSTALLATION
L
Fig. 6.13
INSTALLATION
To the external
control device
To the fused
spur isolation
switch
N
Fig. 6.16
• Connect the room thermostat between terminals 1 and 3 as shown in Fig. 6.17.
Do not connect live wires to terminals to which the room thermostat must be connected.
INSTALLATION
Room
thermostat
T
L
N
Power supply
terminal block
Fig. 6.18
6.10 External frost protection
• Connect the frost thermostat between
terminals 1 and 2 as shown in Fig. 6.19.
Do not connect live wires to terminals
to which the room thermostat must be
connected.
Frost thermostat
Room thermostat
L
3
1
External controls
terminal block
T
N
T
Fig. 6.17
• Route the electrical supply flexible
and the external control flexible
as illustrated in Fig. 6.18. Lock the
ible cords in place with the flexible
clamps.
- 50 -
2
cord
cord
flexcord
3
Fig. 6.19
1
Power supply
terminal block
External controls
terminal block
COMMISSIONING
7.1
COMMISSIONING
Warnings
The commissioning of this boiler and
system must only be undertaken by a
professionally qualified person in accordance with the requirements of the
Gas Safe Installation and Use Regulations and be approved by Gas Safe.
Ensure that the Benchmark Checklist is
satisfactorily completed during the commissioning process. The Checklist is
located at the end of this manual. This
manual should be handed to the User
following completion of the installation
and commissioning process. Failure to
comply with these requirements may invalidate the manufacturers guarantee.
For Ireland (IE), it is necessary to complete a “Declaration of Conformity” to
indicate compliance to I.S.813.2002.
7.2
Electrical installation
Preliminary electrical system checks to ensure electrical safety shall be carried out by
a competent person. i.e. polarity, earth continuity, resistance to earth and short circuit.
If a fault has occurred on the appliance the
fault finding procedure should be followed
as specified in the service manual.
7.3
14
Fig. 7.1
Open position
7.4
Filling the d.h.w. system
7.5
Initial filling of the system
• Close all hot water draw-off taps.
• Open the cold water inlet valve.
• Slowly open each draw-off tap and close
it only when clear water, free of bubbles,
flows out.
• Open the c.h. flow and return valves.
• Remove the front panel of the case (section "Dismantling the external panels" to
page 59).
• Unscrew the cap on the automatic air
purger valve 27 in Fig. 7.2 one full turn
and leave open permanently.
27
Gas supply installation
• Inspect the entire installation including the
gas meter, test for tightness and purge, all
as described in BS 6891;
For Ireland (IE), refer to I.S.813.2002.
• Open the gas cock 14 (Fig. 7.1) on the appliance and check the gas connector on
the appliance for leaks.
Fig. 7.2
• Gradually open stopcock at the filling point
connection to the c.h. system until water is
- 51 -
INSTALLATION
7
COMMISSIONING
INSTALLATION
heard to flow; do not open fully.
• Open each radiator air vent starting at
the lowest point of the system and close
it only when clear water, free of bubbles,
flows out.
• Continue filling the system. The actual
reading should ideally be 1,3 bar and not
less than 0,3 bar.
• Close all air release valves on the c.h.
system.
• Inspect the boiler and the system for water soundness and remedy any leaks discovered.
• Cold flush the system to remove any
loose particles and any system debris before starting the boiler for the first time
The flushing procedure must be in line
with BS7593:2006 Treatment of Water in
d.h.w. c.h. Systems.
When the installation and second filling are completed turn on the c.h. system and run it until the temperature has
reached the boiler operating temperature. The system must then be immediately flushed through.
This procedure must be repeated twice
more.
During this operation we highly recommend the use of a c.h. flushing detergent
in the quantities as specified by the appropriate manufacturer, whose function
it is to dissolve any foreign matter which
may be in the system.
The above operation could save the invalidation of your boilers guarantee and
will also prevent problems which you
may experience in the future if an inhibitor is not used.
Check pump operation/pump release
The pump electronic control circuit automatically releases the pump.
• Turn on the electricity supply to the boiler, switching on the fused spur isolation
- 52 -
switch. The appliance operation light 10
will flash every 4 seconds.
• Turn the function selector 8 as in Fig. 7.3.
The appliance operation light 10 will flash
every 2 seconds.
10
Fig. 7.3
8
7 6
The boiler will now go through an ignition
sequence and the burner will light.
• Make sure that the ambient thermostat is
in the “heat demand” position.
• Check that the boiler with the gas cock
shut-off goes into ignition lockout (Er01)
and, in the meantime, check the pump release.
• The pump release can be verified by
checking that the pump motor vibrates.
• If the pump motor does not vibrate, release the boiler from its lockout due to gas
failure by pressing the reset button on the
control panel and repeat the sequence a
maximum of 10 times.
• If the pump does not release, contact
technical support.
• Once the pump has been released, open
the gas cock and check that the boiler operates correctly both in domestic hot water and heating modes.
• Check the gas pressures and flow rates
as shown in section "GAS CONVERSION" to page 57 of this booklet.
• Check that the condensate produced during functioning fills the pipe and is regularly drained in the draining plant pipe.
• To turn the boiler off set the function selector 8 to the position shown in Fig. 7.4.
The appliance operation light 10 will flash
COMMISSIONING
every 4 seconds.
bow, pour the water through the flue sampling point (Fig. 7.6)
Sampling points
Flue exhaust
8
If during the ignition attempt period the
boiler fails to light, the full sequence control
p.c.b. will go to lockout and the lock-out signal lamp 6 will appear.
To reset the boiler press and release the
boiler reset button 7.
7.6
Condensate pipe and traps
The full length of the condensate pipe
should be check for leaks.
The boiler has a built-in condensate trap
provided with a ball valve that prevents the
escape of combustion products when the
trap is empty.
It is however recommended that any other trap in the drain system is correctly
filled with water before to run the boiler.
Fill the built in condensate trap
by removing the flue elbow and
pouring a cupful of water into
the flue outlet (Fig. 7.5).
Fig. 7.6
7.7
Lighting the boiler
Some products incorporate an anti cycling
time delay. It is normal when first switching the boiler on for the boiler to operate on
heating for a few seconds then switch off.
After 3-4 minutes has elapsed the boiler will
then re ignite and operate perfectly normally. The ignition delay cycle does not prevent
normal operation of the boiler to provide
d.h.w.
If external controls are fitted (e.g. Timeclock,
room thermostat) ensure they ”call for heat”.
• Turn on the electricity supply to the boiler, switching on the fused spur isolation
switch. The appliance operation light 10
will flash every 4 seconds.
• Turn the function selector 8 as in Fig. 7.7.
The appliance operation light 10 will flash
every 2 seconds.
10
Fig. 7.5
An alternative, to the removal of the flue el-
Fig. 7.7
8
7 6
The boiler will now go through an ignition
sequence and the burner will light.
- 53 -
INSTALLATION
10
Fig. 7.4
COMMISSIONING
If during the ignition attempt period the
boiler fails to light, the full sequence control
p.c.b. will go to lockout and the lock-out signal lamp 6 will appear.
To reset the boiler press and release the
boiler reset button 7.
moving the electrical connector A (Fig.
7.8).
32
7.8
Checking the gas pressure at
the burner
INSTALLATION
This boiler has been factory tested to the
highest quality control standards.
The maximum and minimum gas pressures are already set during this quality
control process however the checking
procedure must be followed to ensure
maximum operating efficiency from the
boiler.
• Remove the front panel of the case (see
section "Dismantling the external panels"
to page 59) and the sealed chamber lid.
• Loosen the internal screw 32 (Fig. 7.8) on
the Outlet Pressure Test Point of the Gas
Valve and connect a pressure gauge using a suitable hose.
• Set the d.h.w. and c.h. temperature control knobs to their maximum position. If
external controls are fitted (e. g. Timeclock, room thermostat) ensure they ”call
for heat”.
• Switch on the boiler and open at least one
hot water tap fully.
• Check the maximum gas pressure and
compare the value on the gauge with the
value indicated in the sections "Technical
Data" on pag. 30 or pag. 34 (gas pressures at the burner), accordingly with the
model of boiler installed.
• Check the maximum gas flow at the gas
meter and compare the value indicated in
the sections "Technical Data" on pag. 30
or pag. 34 (gas rate), accordingly with the
model of boiler installed.
• Switch off the boiler.
• Disconnect the gas modulator coil by re- 54 -
A
Fig. 7.8
• Switch on the boiler.
• Check the minimum gas pressure and
compare the value on the gauge with the
value indicated in the sections "Technical
Data" on pag. 30 or pag. 34 (gas pressures at the burner), accordingly with the
model of boiler installed.
• Switch off the boiler and re-connect the
electrical connector A to the modulator
coil.
• Switch on the boiler.
• Check that the boiler lights up uniformly. If
not refer to section “Ignition gas pressure
adjustment” of the Service Manual for the
necessary adjustment procedures.
• Switch off the boiler, turn off the hot water
tap(s) and disconnect the pressure gauge.
• Reassemble the sealed chamber lid and
the front panel of the case (see "Dismantling the external panels" to page 59).
If the maximum and minimum gas pressures measured above are not in accordance with the technical data (sections
"Technical Data" section pag. 30 or pag.
34) then adjustment will be necessary. A
full explanation of the gas pressure ad-
COMMISSIONING
Important: after the gas pressure checks
and any adjustment operations, all of the
test points and adjustment devices must
be sealed. Replace the adjustment protection cap.
7.9
Checking the burner ignition
• Turn the boiler OFF.
• Open the gas valve outlet pressure test
point 32 (Fig. 7.8) and connect the gauge.
• Turn the boiler ON positioning the control
selectors 8 in the positions as shown in as
in Fig. 7.9 and ensure that the timer selector switch and room thermostat, if fitted,
are set to “heat demand”.
10
Fig. 7.9
8
• Watch the gauge and check to see if the
ignition pressure registered corresponds
to the values as given in the Technical
Data. Turn off the boiler and reignite it by
turning the function selector 8 to the OFF
position and then back to that indicated in
Fig. 7.9.
• Repeat this process two to three times
leaving 30 second intervals between each
ignition. Check the ignition pressures and
visually check that the burner lights uniformly and in a controlled manner.
• If the burner ignition is not uniformly con-
trolled then checks should be made to:
-- the flue installation and termination.
-- that the flue gasket as shown in Fig. 6.5
on page 45 is in place.
-- that the burner and injectors are clean.
-- that the boiler is set for the correct gas
used (see "GAS CONVERSION" to
page 57).
• If the ignition pressure recorded is not as
indicated in the Technical Data then refer
to section “Ignition gas pressure adjustment” of the Service Manual for the necessary adjustment procedures.
Important: after the gas pressure checks
and any adjustment operations, all of the
test points must be sealed and replace
the adjustment protection cap.
7.10 Checking the ignition device
With the burner on high flame close the gas
cock.
After three ignition attempts (within about
three minutes), the lock-out signal lamp 6on
page 8 must appear.
To reset the boiler press and release the
boiler reset button 7on page 8.
7.11 Checking the flue system
The flue system should be visually checked
for soundness. Check all clamps, gaskets
and fixing are secure and tight.
Ensure that the flue terminal is sited correctly in accordance with the flue fitting instructions and Fig. 5.1 on page 39 of this
manual.
To carry out a combustion check refer to the
instructions given in the section "Combustion analysis check" to page 60.
Reference figures are given in the "Technical Data" section page 30 of this manual
(Flue gas figures).
- 55 -
INSTALLATION
justment procedure is given in the Gas
Valve section of the service manual. If
maximum and/or minimum gas pressures are adjusted then the ignition gas
pressure must be checked and adjusted
if necessary.
COMMISSIONING
INSTALLATION
7.12 Check pump operation/pump
release
The pump electronic control circuit automatically releases the pump.
Connect the boiler to the mains .
Make sure that the ambient thermostat is in
the “heat demand” position.
Check that the boiler with the gas cock shutoff goes into ignition lockout (Er01) and, in the
meantime, check the pump release.
The pump release can be verified by checking
that the pump motor vibrates.
If the pump motor does not vibrate, release
the boiler from its lockout due to gas failure
by pressing the reset button on the control
panel and repeat the sequence a maximum of
10 times.
If the pump does not release, contact technical
support.
Once the pump has been released, open the
gas cock and check that the boiler operates
correctly both in domestic hot water and heating modes.
7.13 Checking the condensate
drain pipe
Check the soundness and integrity of the
condensate drain pipe.
Verify the cleanness and correct filling of the
condensate traps.
7.14 Instructing the user
Hand over this combined User & Installation
manual and the Service manual to the end
user and explain how to use the unit in both
c.h. and d.h.w. modes.
Take the User step by step through the lighting instructions.
Show the User how to switch off the appliance quickly and indicate the position of the
electric supply isolator.
Explain the proper use and adjustment of all
system controls; this will ensure the great- 56 -
est possible fuel economy.
Explain the function and use of the function
selector.
Explain and demonstrate the function of
time and temperature controls (if fitted).
Explain how to turn off the appliance for
both short and long periods and advise on
the precautions necessary to prevent damage should the appliance be inoperative
when freezing conditions may occur.
Fill in the details required on the Boiler
Guarantee Certificate and hand to the User
advising them to return the correct section
for boiler Guarantee registration.
Finally, advise the User that, for continued
safe and efficient operation, the appliance
must be serviced by a competent person at
least once a year.
GAS CONVERSION
8
GAS CONVERSION
8.1
Warnings
The commissioning of this boiler and
system must only be undertaken by Safety Registered Engineer,qualified to work
on Liquefied Gas Petroleum Gas (LPG)
• Re-assemble the burner, the front panel of
the combustion chamber.
• Switch on the appliance at the mains isolating spur.
• Turn the boiler OFF positioning the function selector 8 as indicated in Fig. 8.2.
Components used to adapt it to the type
of gas available must be genuine parts
only.
Procedures
Check that the gas cock fitted
under the boiler is turned off and
the appliance is switched off at
the mains isolating spur.
8.2
8
10
Fig. 8.2
• Disconnect the electrical connectors of the
C.h. temperature probe NTC 23 in Fig. 8.3
23
Fig. 8.1
• Remove the front panel of the case (see
the section General access and emptying
hydraulic circuits in the service manual).
• Take off the lid of the sealed chamber.
• Take the front panel of the combustion
chamber off and remove the burner (41on
page 28). See section Ignition and detection electrodes in the service manual for
detailed instructions.
• Carry out the conversion for the type of
gas, replacing the burner injectors correctly.
Fig. 8.3
• Keep pressed the reset button 7 for about
10 seconds until the lock-out signal lamp
6 blinks.
• Connect the electrical connectors of the
C.h. temperature probe NTC 23 in Fig. 8.3.
• Press the reset button 7 repeatedly (4
times) until the lamps 10 give the indication as in Fig. 8.4 (gas type mode).
Where:
Fig. 8.4
Lamp OFF
Lamp ON
At this step it is possible to visualize the cur- 57 -
MAINTENANCE
14
Closed position
GAS CONVERSION
rent setting by keeping the reset button 7
pressed for more than 5 seconds. The lamps
10 will flash a number of times corresponding to the setting of the knob 9 in Fig. 8.5.
L.P.G.
4
Gas type
Setting No.
NATURAL
GAS
1
Fig. 8.7
9
Fig. 8.5
Gas
supply
Position
of knob 9
Approx. Max current through the
modulator device
Natural
gas
1
125 mA
L.P.G.
4
165 mA
MAINTENANCE
Fig. 8.6
• To change the setting turn the knob 9 on
a position corresponding to the gas used
as shown in Fig. 8.5. By turning the knob
9, the lock-out signal lamp 6 blinks quickly
(2 per seconds) indicating that the setting
has changed and must be memorised.
• To memorize the setting keep pressed the
reset button 7 for about 5 seconds until the
lamps 10 briefly blinks simultaneously.
• Open the gas cock (14 in Fig. 8.7).
• To reset the boiler to the normal operation
turn it ON by the function selector 8 on the
desired operation and checking the ignition pressure and that the burner lights up
uniformly. In any case, the boiler automatically resets to its normal operation after 10
minutes.
- 58 -
Factory setting = Natural gas (as illustrated)
14
Open position
• Calibrate the gas valve according to the
instructions given in the service manual,
section Modulating gas valve-Adjustment.
• Re-assemble the lid of the sealed chamber.
• Replace the self-adhesive label indicating
the type of gas, and the gas pressures to
which the appliance has been set with the
label included with the conversion kit. The
label is placed on the botton of the appliance.
• Replace the adjustment protection cap.
• Replace the front panels of the case.
MAINTENANCE
9
MAINTENANCE
Warnings
9.1
The procedures detailed in this chapter
must be carried out only by a Gas Safety
Registered Engineer.
Thus you are advised to contact an Authorised Service Agent.
For Ireland (IE), the servicing work must
be carried out by a competent Person.
For efficient and continuous operation of the
boiler you are advised to have, at least once
a year, maintenance and cleaning done by
an Approved Service Engineer.
Isolate the appliance from the electricity
supply by turning off the fused spur isolation switch adjacent to the appliance and
turn off the gas cock, before carrying out
any procedures, whatsoever, for cleaning,
maintenance, opening or dismantling boiler
panels.
9.2
Dismantling the external
panels
Front panel
• Loosen the three screws A (Fig. 9.1).
• Lift and remove the panel.
B
Fig. 9.2
9.3
Emptying the d.h.w. system
9.4
Emptying the c.h. system
• Turn off the d.c.w .inlet isolating valve and
turn on the hot water taps and any drain
cocks.
• Close the c.h. isolating valves.
• Open the central heating drain cock (25
in Fig. 9.3).
Flue exhaust
Sampling point
A
Fig. 9.3
Fig. 9.1
Side panels
• Loosen the screws B. Bring the bottom
of the panels away from the boiler and
lift them, freeing them from the top hooks
(Fig. 9.2).
• A small quantity of water will remain in
the d.h.w. heat exchanger after draining.
If the boiler is being drained to prevent
freezing, the d.h.w. heat exchanger must
be removed and inverted to drain fully or
an antifreeze solution added.
- 59 -
MAINTENANCE
25
Air
Sampling point
MAINTENANCE
9.5
Combustion analysis check
If it is necessary to carry out a combustion
analysis remove the plugs indicated in Fig.
9.1.
Reference figures are given in the sections
"Technical Data" on pag. 30 or pag. 34 (Flue
gas figures).
9.6
Cleaning the primary heat
exchanger
• Take off the front of the case.
• Take off the removable front of the sealed
chamber and the front panel of the combustion chamber.
If you notice dirt on the fins of the primary
heat exchanger (43on page 28):
• Cover the sloping surfaces of the burner
(41on page 28) entirely in a protective
layer (sheets of newspaper or similar).
• Brush out the primary heat exchanger
(43on page 28) with a bristle paintbrush.
MAINTENANCE
9.7
Checking the pressurisation
in the expansion vessel
Empty the central heating systemas described in section "Emptying the c.h. system" to page 59 and check that the expansion vessel pressure is not less than 1 bar.
See also section "Expansion vessel" to
page 29.
If the pressure is lower, take steps to correct
the pressure level
9.8
Cleaning the burner
The sloping and multi-gas type burner
(41on page 28) does not need special maintenance, but it is sufficient to dust it with a
bristle paintbrush.
To reach the burner:
• Take off the front of the case.
• Take off the removable front of the sealed
chamber and the front panel of the com- 60 -
bustion chamber.
• Brush out the burner with a bristle paintbrush.
9.9
Checking the flue
Have the integrity of the flue outlet pipe
(49on page 28) air intake pipe (50on page
28), checked periodically, the air pressure
sensor* (19on page 27) and the efficiency
of the flue safety circuit checked at least
once a year.
* For details see the section Fan and air
pressure sensor in the service manual.
For all the above maintenance operations
it is advisable to call an approved Service
Engineer.
9.10 Drain pipe inspection
Check the soundness and integrity of the
condensate drain pipe.
Verify the cleaness and correct filling of the
condensate traps.
9.11 Visual inspection of appliance
Visually inspect all water joints, seals and
connections for any evidence of leakage
and retighten, grease or replace them as
necessary.
9.12 Gas pressures and tightness
Check appliance for gas tightness. Recheck
operational pressures and adjust as necessary as described in section "Checking the
gas pressure at the burner" to page 54.
9.13 Water inhibitor concentration
Where chemical products are used the level
of water treatment should be checked on an
annual basis and re treated after full or partial drain down.
MAINTENANCE
10 BENCHMARK COMMISSIONING AND SERVICING SECTION
It is a requirement that the boiler is installed and commissioned to the manufacturers instructions and the data fields on the commissioning checklist completed in full.
To instigate the boiler guarantee the boiler needs to be registered with the manufacturer
within one month of the installation.
To maintain the boiler guarantee it is essential that the boiler is serviced annually by a Gas
Safe registered engineer who has been trained on the boiler installed.
The service details should be recorded on the Benchmark Service Interval Record and left
with the householder.
MAINTENANCE
www.centralheating.co.uk
- 61 -
GAS BOILER SYSTEM COMMISSIONING CHECKLIST
This Commissioning Checklist is to be completed in full by the competent person who commissioned the boiler as a means of demonstrating
compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference.
Failure to install and commission according to the manufacturer’s instructions and complete this Benchmark Commissioning Checklist will invalidate the
warranty. This does not affect the customer’s statutory rights.
Customer name:
Telephone number:
Address:
Boiler make and model:
Boiler serial number:
Commissioned by (PRINT NAME):
Gas Safe register number:
Company name:
Telephone number:
Company address:
Commissioning date:
To be completed by the customer on receipt of a Building Regulations Compliance Certificate*
Building Regulations Notification Number (if applicable):
CONTROLS (tick the appropriate boxes)
Time and temperature control to heating
Time and temperature control to hot water
Room thermostat and programmer/timer
Programmable room thermostat
Load/weather compensation
Optimum start control
Cylinder thermostat and programmer/timer
Combination Boiler
Heating zone valves
Fitted
Not required
Hot water zone valves
Fitted
Not required
Thermostatic radiator valves
Fitted
Not required
Automatic bypass to system
Fitted
Not required
Boiler interlock
Provided
ALL SYSTEMS
The system has been flushed and cleaned in accordance with BS7593 and boiler manufacturer’s instructions
Yes
What system cleaner was used?
What inhibitor was used?
Quantity litres
Has a primary water system filter been installed?
No
Yes
CENTRAL HEATING MODE measure and record:
Gas rate
m³/hr
OR
ft³/hr
Burner operating pressure (if applicable)
mbar
OR Gas inlet pressure
mbar
Central heating flow temperature
°C
Central heating return temperature
°C
COMBINATION BOILERS ONLY
Is the installation in a hard water area (above 200ppm)?
Yes
No
If yes, and if required by the manufacturer, has a water scale reducer been fitted?
Yes
No
What type of scale reducer has been fitted?
DOMESTIC HOT WATER MODE Measure and Record:
OR
Gas rate
m³/hr
Burner operating pressure (at maximum rate)
mbar OR Gas inlet pressure at maximum rate
ft³/hr
mbar
Cold water inlet temperature
°C
Hot water has been checked at all outlets
Yes
Temperature
°C
Water flow rate
I/min
CONDENSING BOILERS ONLY
The condensate drain has been installed in accordance with the manufacturer’s instructions and/or BS5546/BS6798
Yes
ALL INSTALLATIONS
Record the following:
At max. rate: CO ppm AND
At min. rate: (where possible) CO ppm AND
CO/CO²
CO/CO²
Ratio
Ratio
The heating and hot water system complies with the appropriate Building Regulations
Yes
The boiler and associated products have been installed and commissioned in accordance with the manufacturer’s instructions
Yes
The operation of the boiler and system controls have been demonstrated to and understood by the customer
Yes
The manufacturer’s literature, including Benchmark Checklist and Service Record, has been explained and left with the customer
Yes
Commissioning Engineer’s Signature
Customer’s Signature
(To confirm satisfactory demonstration and receipt of manufacturer’s literature)
*AllinstallationsinEnglandandWalesmustbenotifiedtoLocalAuthorityBuildingControl(LABC)eitherdirectlyorthrougha
CompetentPersonsScheme.ABuildingRegulationsComplianceCertificatewillthenbeissuedtothecustomer.
© Heating and Hotwater Industry Council (HHIC)
www.centralheating.co.uk
SERVICE RECORD
It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed.
Service Provider
Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the manufacturer’s instructions.
Always use the manufacturer’s specified spare part when replacing controls.
SERVICE 01
Date:
Engineer name:
SERVICE 02
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Record:
Gas safe register No:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Comments:
CO² %
CO² %
Signature
Record:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Comments:
Date:
Engineer name:
SERVICE 04
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Gas safe register No:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Comments:
CO² %
CO² %
Signature
Record:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Comments:
Date:
Engineer name:
SERVICE 06
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Gas safe register No:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Date:
Engineer name:
Company name:
Comments:
CO² %
CO² %
Signature
Record:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Comments:
CO² %
CO² %
Signature
SERVICE 07
Date:
Engineer name:
SERVICE 08
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Gas safe register No:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Date:
Engineer name:
Company name:
Comments:
CO² %
CO² %
Signature
Record:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Comments:
CO² %
CO² %
Signature
SERVICE 09
Date:
Engineer name:
SERVICE 10
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Gas safe register No:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Date:
Engineer name:
Company name:
Record:
CO² %
CO² %
Signature
SERVICE 05
Record:
Date:
Engineer name:
Company name:
Record:
CO² %
CO² %
Signature
SERVICE 03
Record:
Date:
Engineer name:
Comments:
Signature
CO² %
CO² %
Record:
CO ppm
AND
At min. rate: (Where Possible) CO ppm
AND
At max. rate:
Comments:
CO² %
CO² %
Signature
*AllinstallationsinEnglandandWalesmustbenotifiedtoLocalAuthorityBuildingControl(LABC)eitherdirectlyorthrougha
CompetentPersonsScheme.ABuildingRegulationsComplianceCertificatewillthenbeissuedtothecustomer.
©HeatingandHotwaterIndustryCouncil(HHIC)
www.centralheating.co.uk
17962.2513.0
061664A5UK
Biasi UK Ltd
Commercial Road
Leamore Enterprise Park
WALSALL
WS2 7NQ
Sales Tel. 01922 714600
Tech. Service Tel. 01922 714636
www.biasi.co.uk
N
05/02
2016
*1796225130*