SCION xB 2008 - Navigation System Part Number: 08545

SCION xB 2008 - Navigation System Part Number: 08545
SCION
xB
2008 -
Navigation System
Preparation
NOTE: Part number of this accessory may not be
the same as the part number shown.
General Applicability
Part Number: 08545-00930
Kit Contents
Item #
1
2
3
4
5
Quantity Reqd.
1
1
1
1
1
Description
Navigation System
GPS Antenna
Wire Harness
DVD-ROM
Owner’s Manual
Recommended Sequence of Application
Item #
1
2
3
4
Hardware Bag Contents
Item #
1
2
3
4
5
6
7
Quantity Reqd.
1
2
5
3
1
8
1
Description
Earth Plate
Cord Clamp
Wire Tie
Foam Tape
Protection Sheet
Bolt(M5×8)
Double Sided Tape
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Item #
Quantity Reqd.
Description
Conflicts
None
Recommended Tools
Personal & Vehicle
Protection
Vehicle protection
Notes
Blankets, Masking tape,
Vinyl tape
Special Tools
Notes
iPod Connector Checker Jig
Toyota P/N: SXA06-038-01
Installation Tools
Notes
Panel Clip Removal Tool
e.g. Toyota SST P/N:00002-06002-01
Open End, 10mm
10mm
Wrench
Socket
Ratchet
Extension
Screwdriver
Torque Wrench
Pliers
Scissors
Nipper
Special Chemicals
02/27/08
Description
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
Phillips
36 lbf ・in
Notes
None
Issue: C
Quantity Reqd.
Legend
Additional Items Required For Installation
Item #
Accessory
Navigation System
Satellite Radio
Subwoofer
Interior lights
Page 1 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
1. Vehicle Protection
(a) Remove the negative battery cable (Fig. 1-1).
Ratchet, 10mm Socket
(1) Protect the fender before starting.
Battery
(2) Do not touch the positive terminal with
any tool when removing cable.
Negative Battery Cable
Fig. 1-1
Panel Removal Tool
Clips (×4)
Masking tape
2. Disassembly of Vehicle
NOTE: Place all removed parts on a protected
surface.
NOTE: When disconnecting wiring connectors
do NOT pull on the wiring, pull on the
connector only.
NOTE: Engage the parking brake while working.
Fig. 2-1
Instrument panel cluster
finish center panel
Claws (×3)
(a) Remove the instrument panel cluster finish
center panel.
(1) Apply masking tape around the
instrument panel cluster finish center
panel (Fig. 2-1).
(2) Disengage the 4 clips and 3 claws and
remove the instrument panel cluster
finish center panel (Fig. 2-1).
Issue: C
02/27/08
Page 2 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(b) Remove the instrument panel cluster finish
lower panel.
Clips (×2)
(1) Disengage the 2 clips and remove the
instrument panel cluster finish lower
panel (Fig. 2-2).
Instrument panel cluster finish lower panel
Fig. 2-2
Ratchet, 10mm Socket, Extension
Bolts (×4)
(c) Remove the radio bracket.
(1) Remove the 4 bolts and remove the radio
bracket (Fig. 2-3).
Radio bracket (L)
Radio bracket (R)
Fig. 2-3
Claws (×10)
(d) Remove the instrument panel cluster finish
panel.
(1) Disengage the 6 clips and 10 claws and
remove the instrument panel cluster
finish panel (Fig. 2-4).
Clips (×6)
Instrument panel cluster finish panel
Fig. 2-4
Phillips Screwdriver
Screws (×4)
(e) Remove the combination meter assembly.
(1) Remove the 4 screws and remove the
combination meter assembly (Fig. 2-5).
(2) Disconnect the connectors (Fig. 2-5).
Combination meter assembly
Fig. 2-5
Issue: C
02/27/08
Page 3 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
Claws (×8)
(f) Remove the instrument panel lower finish
panel.
Clips (×2)
(1) Disengage the 2 clips and 8 claws and
remove the instrument panel lower finish
panel (Fig. 2-6).
(2) Disconnect the connectors (Fig. 2-6).
Instrument panel lower finish panel
Fig. 2-6
(g) Remove the center console side cover (L)
Guide
(1) Disengage the 3 claws and remove the
center console side cover (L) (Fig. 2-7).
A
NOTE: Disengage the claws while keeping
pressure on the area indicated by the
(A) in the illustration.
Center console side cover (L)
Fig. 2-7
Claws (×3)
Claws (×3)
(h) Remove the center console side cover (R).
Guide
(1) Disengage the 3 claws and remove the
center console side cover (R) (Fig. 2-8).
A
Fig. 2-8
Issue: C
02/27/08
NOTE: Disengage the claws while keeping
pressure on the area indicated by the
(A) in the illustration.
Center console side cover (R)
Page 4 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
For Manual Transmission Model Only
Panel Removal Tool
(i) Remove the center console upper cover.
D
C
(1) Remove the shift lever knob (Fig. 2-9).
C
Shift lever knob
(2) Disengage the 2 clips and 4 claws and
remove the center console upper cover
(Fig. 2-9).
B
B
Clips (×2)
Claws (×4)
A
Fig. 2-9
Center console upper cover
(3) Disconnect the connectors (Fig. 2-9).
NOTE: Disengage the clips and claws in the
order (A) to (C) as shown in the
illustration. Disengage claw (C)
while keeping pressure on the area
indicated by the (D) in the
illustration.
For Automatic Transmission Model Only
Panel Removal Tool
C
(j) Remove the center console upper cover.
D
C
B
Claws (×12)
B
Fig. 2-10
A
Phillips Screwdriver
Center console upper cover
Clips (×6)
(1) Disengage the 2 clips and 10 claws and
remove the center console upper cover
(Fig. 2-10).
(2) Disconnect the connectors (Fig. 2-10).
NOTE: Disengage the clips and claws in the
order (A) to (C) as shown in the
illustration. Disengage claw (C)
while keeping pressure on the area
indicated by the (D) in the
illustration.
(k) Remove the center console.
(1) Remove the 4 screws and disengage the 6
clips, then remove the center console
(Fig. 2-11).
(2) Disconnect the connectors (Fig. 2-11).
Screws (×4)
Guides (×2)
Fig. 2-11
Issue: C
Center console
02/27/08
Page 5 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(l) Remove the rear console upper cover.
Rear console upper cover
(1) Disengage the clip and 7 claws and
remove the rear console upper cover
(Fig 2-12).
Clip
Front
Fig. 2-12
Ratchet, 10mm Socket, Extension
Claws (×7)
Non-woven fabric
(m) Remove the 3 bolts and 2 plastic clips from
rear console box.
(1) Remove the non-woven fabric (Fig. 2-13).
(2) Remove the 3 bolts and 2 plastic clips
(Fig. 2-13).
Bolts (×3)
Rear console box
Fig. 2-13
Plastic clips (×2)
NOTE: Perform the wiring operation with
the rear console box lifted. It is not
necessary to disconnect the
connectors.
3. Navigation System Installation
(a) Foam Tape Cut Procedures.
Scissors
Foam tape
×4
×22
Fig. 3-1
Issue: C
02/27/08
(1) As shown in the illustration, cut foam
tape into 4 large pieces and 22 small
pieces (Fig. 3-1).
NOTE: <Large pieces>
・Used to bundle excess antenna cord
and wire harness.
<Small pieces>
・Used to fix the antenna cord.
・Used to fix the REV signal wire.
・Used to fix the PKB signal wire.
・Used to fix the video cord
・Used to fix the GPS antenna.
Page 6 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
Scissors
SPD signal wire
(Violet / White)
Approx.
50mm
(b) Cut the SPD signal wire.
(1) Cut the SPD signal wire (Violet / White)
from the wire harness to the length
(approx. 50mm) shown in the illustration
(Fig. 3-2).
Insulation
(2) Wrap the SPD signal wire (Violet /
White) with vinyl tape as shown in the
illustration (Fig. 3-2).
Vinyl tape
Fig. 3-2
NOTE: It is not necessary to connect the
SPD signal wire (Violet / White)
from the wire harness.
(c) Remove the radio harness and antenna cable.
Antenna Cable
Radio harness
(1) Remove the taping securing the harness
(Fig. 3-3).
(2) Pull out the antenna cable from the
instrument panel hub (Fig. 3-3).
Tapings(×2)
Taping-B
Slit
Taping-A
Taping-A
1. Grab and pull the
connectors to tear tapingA apart.
Taping-A
Taping-A
Taping-B
3. Remove taping-B from
the harness and pull the
audio harness out.
2. Remove taping-A
from the harness.
Fig. 3-3
Issue: C
02/27/08
Page 7 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(d) Install the GPS antenna.
Scissors
Side View
GPS antenna
Front
Double sided tape lengths
Double sided tapes
(×3)
(2) Remove the release paper from the earth
plate and apply 3 pieces of double sided
tape to the bottom of the earth plate
(Fig. 3-4-2).
10mm
Earth plate
Fig. 3-4-1
Fig. 3-4-2
(1) Cut some pieces of double sided tape to
the length shown in the illustration
(Fig. 3-4-1).
GPS antenna
(3) Attach the earth plate onto the air
conditioning duct behind the combination
meter (Fig. 3-4).
Earth plate
(4) Place the GPS antenna onto the center of
the earth plate (Fig. 3-4).
NOTE: Before attaching any double sided
tape, wipe off any dirt, water or oil
from the attachment surface.
Earth plate attachment
position
Air conditioning duct
Fig. 3-4
(e) Route the antenna cord.
GPS antenna
Top View
(1) Secure the GPS antenna with foam tape
as shown in the illustration (Fig. 3-5).
Cord clamp
Foam tape
Foam tapes (×4)
Fig. 3-5
(2) Route the antenna cord to the navigation
system installation location and fix it to
the air conditioning duct with a cord
clamp and foam tape (Fig. 3-5).
Antenna cord
(f) Route the wire harness.
REV signal wire (Green)
PKB signal wire
(Red / White)
Antenna cord
(1) Fix the wire harness and antenna cord to
the vehicle wire harness with a wire tie
(Fig. 3-6).
Wire tie
Fig. 3-6
Issue: C
02/27/08
Vehicle wire harness
Page 8 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(g) Temporarily route the REV signal wire.
Vehicle wire harness
(1) Temporarily route the REV signal wire
(Green) from the wire harness along the
vehicle wire harness (Fig. 3-7).
REV signal wire (Green)
Fig. 3-7
REV signal wire (Green)
Top View
(2) Temporarily route the REV signal wire
(Green) from the wire harness to the
white 30P connector in the instrument
panel J/B (Fig. 3-8).
30P Connector
(White)
Instrument panel J/B
Fig. 3-8
(h) Connect the REV signal wire.
Vehicle wire harness (Red)
(1) Pull the cord shown in the illustration out
from the white 30P connector bundle
(Fig. 3-9).
30P on the wire
harness side
Fig. 3-9
30P Connector (White)
Pliers
Splicing
connector
Vinyl tape
Pliers
Fig. 3-10
Issue: C
02/27/08
NOTE: Check the terminal number of the
wire harness and be sure to connect
the correct wire since there are many
wires with the same colors.
(2) Connect the red wire from the white 30P
connector to the REV signal wire (Green)
from the wire harness (Fig. 3-10).
(3) Wrap vinyl tape around the splicing
connector (Fig. 3-10).
Vehicle wire harness (Red)
Page 9 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(i) Fix the REV signal wire.
REV signal wire (Green)
Vehicle wire harness
(1) Take the REV signal wire (Green) from
the wire harness and fix it to the vehicle
wire harness with foam tape (Fig. 3-11)
Foam tapes (×3)
Instrument panel J/B
Fig. 3-11
REV signal wire (Green)
Foam tapes (×4)
(2) Take the REV signal wire (Green) from
the wire harness and fix it to the vehicle
wire harness with foam tape (Fig. 3-12).
Vehicle wire harness
Fig. 3-12
(j) Temporarily route the PKB signal wire.
Vehicle wire harness
(1) Remove the plastic clip and pull back the
floor carpet (Fig. 3-13).
(2) Route the PKB signal wire (Red / White)
from the wire harness along the vehicle
wire harness (Fig. 3-13).
Plastic clip
Fig. 3-13
PKB signal wire (Red / White)
(3) Temporarily route the PKB signal wire
(Red / White) from the wire harness
along the vehicle wire harness to the
white 1P connector on the parking brake
switch. (Fig. 3-14).
PKB signal wire (Red / White)
Rear console box
NOTE: The signal wire can be easily routed by
removing the driver side floor carpet and
lifting the rear console box.
Front
Fig. 3-14
Issue: C
02/27/08
Parking brake 1P connector (White)
Page 10 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(k) Connect the PKB signal wire.
Scissors
20mm~
30mm
Tube
(1) Cut the vehicle wire harness tube, as
shown in the illustration (Fig. 3-15) .
NOTE: Be careful not to cut the vehicle wire
harness when cutting the tube.
Parking brake 1P connector (White)
Fig. 3-15
Pliers
Vehicle wire harness (Black)
Splicing
connector
Pliers
(2) Connect the PKB signal wire (Red /
White) from the wire harness to the lead
wire from the white 1P connector
(Fig. 3-16)
(3) Wrap vinyl tape around the splicing
connector (Fig. 3-16).
Vinyl tape
Fig. 3-16
(l) Fix the PKB signal wire
PKB signal wire (Red / White)
(1) Take the PKB signal wire (Red / White)
from the wire harness and fix it to the
vehicle wire harness with foam tape
(Fig. 3-17).
Foam tapes (×3)
Vehicle wire harness
Fig. 3-17
PKB signal wire (Red / White)
(2) Take the PKB signal wire (Red / White)
from the wire harness and fix it without
any slack to the vehicle wire harness
using foam tape (Fig. 3-18).
Vehicle wire harness
Fig. 3-18
Issue: C
Foam tapes (×5)
02/27/08
Page 11 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(m) Bundle any excess wire harness and antenna
cord.
Scissors
Protection Sheet(30×45mm)
Protection Sheet
(30×45mm)
(1) Cut two pieces of a protection sheet, as
shown in the illustration (Fig. 3-19).
A
Fig. 3-19
(2) Apply the pieces of the protection sheet
to the areas indicated by the (A) in the
illustration (Fig. 3-19).
A
Space for excess wire harness
(3) Bundle the wire harness and antenna cord
and fix them to the air conditioning unit
shown in the illustration with wire tie and
foam tape (Fig. 3-20).
Wire tie
Antenna cord
Foam tapes (×2)
Foam tapes (×2)
Wire harness
Fig. 3-20
(n) Fix the video cord.
Video cord
Foam tape
(1) Remove the vinyl covering from the
video cord (Fig. 3-21).
(2) Fix the video cord to the navigation
system with foam tape (Fig. 3-21).
Fig. 3-21
Issue: C
02/27/08
Navigation system
Page 12 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(o) Install the brackets.
Phillips Screwdriver
Left Side View
(1) Install the brackets (L and R) onto the
navigation system with the 8 bolts
(M5×8) (Fig. 3-22).
Right Side View
Radio bracket (L)
Radio bracket (R)
Navigation system
Fig. 3-22
Bolts (M5×8) (×8)
(p) Install the navigation system.
Ratchet, 10mm Socket, Extension
(1) Connect the connectors (20P /16P /10P /
6P / Wire harness / GPS antenna cable /
Radio antenna cable) to the navigation
system (Fig. 3-23).
(2) Install the navigation system with the 4
bolts (Fig. 3-23).
Navigation system
Fig. 3-23
Bolts (×4)
4. In-process function check - Check REV/PKB
signal wire connection
(a) Reconnect the vehicle’s negative battery
Torque Wrench, 10mm Socket
Battery
Negative Battery
Cable
cable (Fig. 4-1).
(1) Position the negative terminal back to
factory position.
(2) Tighten the nut to 36 in-lbs.
(3) Do not touch the positive terminal with
any tool when replacing the cable.
(4) Connect DCC Fuse.
Fig. 4-1
(5) Install Navigation DVD.
Issue: C
02/27/08
Page 13 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(b) Press the "DISP" button to display the initial
search screen. (Fig. 4-2).
Fig. 4-2
(c) In order to display the "System Check Mode"
screen, touch areas A and B, indicated on the
screen, in the following order:
A
A→B→A→B→A→B・・・・・・(Fig. 4-3).
B
Fig. 4-3
(d) Touch "Menu" to display the "Diagnosis
Menu" screen (Fig. 4-4).
Fig. 4-4
(e) Touch "Display Check" to display the
"Display Check" screen (Fig. 4-5).
Fig. 4-5
Issue: C
02/27/08
Page 14 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
(f) Touch "Vehicle Signal Check" to display the
"Vehicle Signal Check" screen (Fig. 4-6).
Fig. 4-6
(g) Perform the following confirmation tests by
referring to the indications circled on the
screen (Fig. 4-7).
PKB
(1) When the PKB is engaged →ON
(2) When the PKB is disengaged →OFF
Fig. 4-7
REV
(3) When the shift lever is engaged in the R
position →ON
(4) When the shift lever is engaged in any
position other than R →OFF
NOTE: If the results are not as specified,
check the connection again.
(h) Terminate the operation by pressing the
"DISP" button on the screen for more than 3
seconds (Fig. 4-8).
Fig. 4-8
Issue: C
02/27/08
Page 15 of 17 pages
SCION
xB
2008 -
Navigation System
Procedure
5. iPod Check Procedure (PORT INSTALL
ONLY – NOT NEEDED FOR DEALER)
iPod Connector
(a) Connect the iPod Connector Checker Jig
(Fig. 5-2) to the vehicle’s iPod Connector
(Fig. 5-1).
(b) Turn on the Acc switch.
(c) Push the iPod Checker Switch on the iPod
Connector Checker Jig.
Center Console
Fig. 5-1
(d) Check LED. LED should turn on to Green.
(If no LED on, then iPod Connector is NG)
(e) Turn off the Acc switch.
iPod Connector Checker Jig,
Toyota P/N SXA06-038-01
Fig. 5-2
(f) Disconnect the iPod Connector Checker Jig
from the Vehicle’s iPod Connector.
NOTE: The iPod Connector Checker Jig is
powered by two AA batteries, which
must be replaced periodically. Life
expectancy of the batteries is
approximately 6 months (or
approximately 12,000 vehicles).
6. Completing the installation
(a) Complete the reassembly of the vehicle.
(1) Reconnect any disconnected connectors.
(2) Verify the panels fit together properly
with no uneven gaps between them.
(b) Clean up and remove any trash.
(c) Place the owner’s manual left in their
protective bags, iPod cable and DVD Jewel
case in the glove box.
Issue: C
02/27/08
Page 16 of 17 pages
SCION
xB
2008 Navigation System
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Accessory Function Checks
Press the “MENU” button and check that the
menu screen appears.
Touch the “Volume” button and check that
the volume level displayed on the volume
screen changes accordingly.
Press the “MAP/VOICE” button and check
that the map screen appears.
Touch and scroll the map displayed on the
screen and check that the map can be
scrolled.
Check for GPS icon on display when under
open sky.
GPS antenna connection is ok
Vehicle Function Checks
Hazard Switch
Functioning Hazard Switch
Air Conditioner
Functioning Air Conditioner
Front Passenger Seat Belt Monitor
Functioning Front Passenger Seat Belt Monitor
Door Key Lock Monitor
Functioning Door Key Lock Monitor
Cigarette Lighter
Functioning Cigarette Lighter
Refer to your Car Owner’s Manual, and
return the Power Windows to their initial
positions.
Auto-open and Auto-close operation of each
of the Power Windows is possible with the
driver’s seat master switch.
Refer to your Car Owner’s Manual, and
return the Back Door Lock to its initial
position.
Door Lock and Unlock functions operate
correctly.
Steering Wheel Audio Controls
Volume, Mode and Seek function
TRAC, TPMS and Combination Meter,
Ensure LED operation
Parking Brake and Reverse
Issue: C
02/27/08
Page 17 of 17 pages
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement