200 PSI-13 Gallon
Operating instructions (ENG)
MODELS:
NWWA2220N
1.006-139.0
NWWE2220N
1.006-675.0
86345350-N
01/16/17
Read these instructions before using the machine.
Machine Data Log / Overview
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
Phone Number:
Sales Representative:
OVERVIEW
The Dominator is an electric powered carpet extractor intended for commercial use. This appliance applies a cleaning solution to the carpet and then vacuums the soiled water back into the recovery tank.
2
Warranty Registration
Thank you for purchasing a Windsor product. Warranty registration is quick and easy.
Your registration will allow us to serve you better over the lifetime of the product.
To register your product go to : www.windsorind.com/WarrantyRegistration.aspx
For customer assistance:
1-800-444-7654
86345350 DOMINATOR 200 PSI
Machine Data Log / Overview. . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . 4
Safety
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . 5
HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . . 6
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operations
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . 9
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pre-Run Inspection . . . . . . . . . . . . . . . . . . . . . . . . . 12
Equipment Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table of Contents
PARTS
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Wand / Hoses - Optional . . . . . . . . . . . . . . . . . . . . 36
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Suggested Spare Parts . . . . . . . . . . . . . . . . . . . . . 40
Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Maintenance
Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . 14
Daily/Regular Maintenance. . . . . . . . . . . . . . . . . . . 14
Vacuum Motor Replacement . . . . . . . . . . . . . . . . . 15
Solution Pump Replacement . . . . . . . . . . . . . . . . . 16
Pressure Regulator . . . . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
86345350 DOMINATOR 200 PSI 3
How to Use This Manual
This manual contains the following sections:
• How to Use This Manual
• Safety
• Operations
• Maintenance
• Parts List
The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the
MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual.
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
Phone Number:
Sales Representative:
The model and serial number of your machine is located approximately where shown.
Serial Number
Tag
The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death.
The OPERATIONS section is to familiarize the operator with the operation and function of the machine.
The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order:
• Maintenance
• Lubrication
• Vacuum Motor Replacement
• Solution Pump Replacement
• Troubleshooting
The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:
• REF – column refers to the reference number on the parts illustration.
• PART NO. – column lists the part number for the part.
• PRV NO. – reference number.
• QTY – column lists the quantity of the part used in that area of the machine.
• DESCRIPTION – column is a brief description of the part.
• SERIAL NO. FROM – If this column has an (*) and a Reference number, see the SERIAL
NUMBERS page in the back of your manual. If column has two asterisk (**), call manufacturer for serial number. The serial number indicates the first machine the part number is applicable to. The main illustration shows the most current design of the machine. When a boxed illustration is shown, it displays the older design.
• NOTES – column for information not noted by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts.
NOTE: The manual part number is located on the
lower left corner of the front cover.
4 86345350 DOMINATOR 200 PSI
Safety
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service.
Use only indoors. Do not use outdoors or expose to rain.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer's recommended components and attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
This machine is intended for cleaning carpet only.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
86345350 DOMINATOR 200 PSI 5
Safety
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -
WARNING
and
CAUTION
and
FOR
SAFETY
. The level of hazard intensity is determined by the following definitions:
WARNING
- Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION
- Hazards or unsafe practices which could result in minor personal injury or product or property damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine.
Use only manufacturer approved replacement parts.
6 86345350 DOMINATOR 200 PSI
Safety
Safety Labels
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels
become illegible, promptly replace them.
Label Warning
86244300
PRV # 500955
WARNING!
FOR YOUR PROTECTION USE A
GROUND FAULT CIRCUIT INTERRUPTER
Label Circuit Interrupter
86200570
PRV # 170-41
86345350 DOMINATOR 200 PSI 7
Safety
THIS PRODUCT IS FOR COMMERCIAL
USE ONLY.
ELECTRICAL:
The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
8 86345350 DOMINATOR 200 PSI
Technical Specifications
Electrical-Australia
Electrical-Europe
Solution Pump
Solution Capacity
Recovery Capacity
Height
Length
Width
Vacuum Motor
Weight- Empty
Weight-Full Solution
Power cord
ITEM
Width
MEASURE
240 Volt, 50 Hz, 9A
230 Volt, 50/60 Hz, 9A
200 psi
13 Gal
11 Gal
43 inches
30 inches
22 inches
Dual 2 Stage
134 lbs
239 lbs
25 feet
Length
Operations
Height
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
86345350 DOMINATOR 200 PSI 9
Operations
1
2
3
4
8
Controls
1.
Vacuum Accessory Tool Hook-up
2.
Solution Pump Switch
3.
Vacuum 1 Switch
4.
Vacuum 2 Switch
7
6
5.
Adjustable Pressure Relief Valve
6.
Breaker for Vacuum 2
7.
Breaker for Vacuum 1
8.
Solution Accessory Tool Hook-up
5
10 86345350 DOMINATOR 200 PSI
Operations
Machine Operation
Care must be exercised in the use of all chemicals.
Chemicals are poisonous and can pose a health risk.
Read and follow manufacturers instructions regarding dangers and correct usages.
Only use chemicals approved for use with this machine. Use of non-compatible chemicals may cause machine damage and will not be covered under the warranty. Carefully read ingredients on manufacturer’s label before using any product in this machine.
Do not let pump run dry.
The internal parts of the pump used in the machine are suitable for use with most carpet cleaning chemicals.
But they are susceptible to chemical attack from some cleaning substances, such as hydrocarbon solvents and chlorinated bleaches. These non-compatible materials are not of the type used for carpet cleaning.
Chemicals
Suitable Chemicals
• Alkalis
• Detergents
• Hydroxides
• Soaps
• Vinegar
Non-Compatible
• Aldehydes
• Aromatics Hydrocarbons
• SP Butyls
• Carbon Tetrachloride
• Clorox*
• Chlorinated Bleaches
• Chlorinated Hydrocarbons
• Lysol*
• Methyl Ethel Ketone (MEK)
• Perchorethylene (perc)
• Phenolics
• Trichlorethylene
• D-Limonene
Do not let pump run unattended.
*Registered Trademark
86345350 DOMINATOR 200 PSI 11
Operations
Pre-Run Inspection
1.
Check all fittings and connectors for proper assembly.
2.
Check all hoses for leaks. Repair or replace any damaged hoses.
3.
Check power cord(s) for any damage. If damaged, replace.
Equipment Set-up
1.
Plug power cord from machine into properly grounded wall outlet.
2.
Turn vacuum motor switch on and off to make sure there is electrical power at machine.
3.
Using a clean container, fill the solution tank with clean hot water. Do not use water over 130°F. Mix in a non-foaming cleaning concentrate for use in hot water extraction machines, following the manufacture's instructions printed on container.
4.
Connect priming hose to solution fitting on machine. Turn on pump and run for 30 seconds or until a steady flow of water is coming out of priming hose. Turn off pump and disconnect priming hose.
5.
Connect vacuum hose to machine. Slide the swivel cuff over the outlet on the tank.
6.
Connect the hose to your machine and wand. Pull back the knurled collar on the quick disconnect coupler and push onto the connection on the chassis. To avoid leaks, check to be that a positive connection was made.
NOTE: When using a powder cleaner, pre-mix with
hot water in a clean container before adding to the solution tank.
7.
Turn pump and vacuum switch(es) to the on position.
12 86345350 DOMINATOR 200 PSI
Cleaning
Always use defoamer if foaming occurs. Foam will suspend large particles that may damage vacuum(s) as well as allow liquid into the vacuum motor(s) without activating the float shutoff.
1.
Prior to cleaning, make certain that the nozzle is functioning properly.
a.
To check, hold the wand about one foot above the surface to be cleaned and open the wand valve. A full spray should be observed from the nozzle.
b.
If the nozzle is not showing a full spray pattern, adjust nozzle for proper pattern, clean, or replace nozzle.
2.
Normally, chemical is applied on the push stroke of the wand when cleaning. Vacuuming is done on the pull stroke. For heavily soiled carpets the wand may be used in a scrubbing manner, applying chemical in both the push and pull stroke.
3.
When cleaning, keep the working opening (wand mouth) flat on the surface being cleaned. Keep the wand moving when the valve is open.
4.
The shutoff float inside the vacuum tank will impede the vacuum flow when the vacuum tank is full. When this occurs, empty the vacuum tank by opening the dump valve and dispose of the waste in a proper manner.
5.
Once the vacuum tank has been emptied, you may once again proceed with cleaning
Operations
86345350 DOMINATOR 200 PSI 13
Maintenance
Periodic Maintenance
Twice a month, flush a white vinegar solution (one quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the machine. This will prevent build-up of alkaline residue in the system.
Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. The electrical cable must be well insulated and cable connector screw kept tight. If the cable insulation is broken or frayed, repair or replace immediately. Don't take chances with electrical fire or shock.
Daily/Regular Maintenance
Before making any repairs or adjustments to the machine, disconnect the power cords from the electrical source.
1.
Empty unused cleaning solution from the solution tank.
2.
Inspect and clean filter screen in solution tank.
3.
Flush pumping system with 1 to 2 gallons of clean water.
4.
After each use, rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if necessary, using a Hospital Grade Virucide or a
10-1 bleach to water solution. Waste water should be disposed of properly.
Do not allow machine to freeze.
SERVICE SCHEDULE
Check machine for cord damage
Check recovery dome and gasket for damage and cleanliness
Check hoses for wear, blockages, or damage
Check handles, switches, and knobs for damage
Run one gallon of water through solution system
Clean out recovery tank and check float valve to make sure it moves freely
Clean out solution tank and remove and clean vacuum intake screen
Clean outside of all tanks and check for damage
Run vac motor for at least one minute to allow motor to dry
Store with dome off tank to allow the tank to dry
Check all gaskets for wear and leakage
Check pump pressure; observe spray pattern and check with gauge if necessary
Check and clean solution screen
Check cables for fraying
Check overall performance of machine
Check vac motor carbon brushes
DAILY WEEKLY QUARTERLY
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
14 86345350 DOMINATOR 200 PSI
Only qualified maintenance personnel are to perform the following repairs.
Vacuum Motor Replacement
1.
Turn off all switches and unplug machine.
2.
Remove hardware under front of machine to access component compartment.
3.
Remove vacuum motor cover and disconnect motor wires.
4.
Remove the vacuum motor.
5.
Reverse process to install vacuum motor.
Maintenance
Vacuum Motor Carbon Brushes Replacement
End Cap
Carbon
Brushes
WARNING: The green ground wire must be attached for safe operation. See wiring diagram.
If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.
Important:
These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.
3
8
[9.5mm]
Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less than
3/8" (9.5mm) long.
86345350 DOMINATOR 200 PSI 15
Maintenance
Solution Pump Replacement
Only qualified maintenance personnel are to perform the following repairs.
PUMP REPLACEMENT KITS
200 PSI
CAM & BEARING KIT
86201170 (EURO)
86349990 (AUSTRALIA)
16
PLUNGER & SEALS KIT
86201150
86345350 DOMINATOR 200 PSI
VALVE & O-RINGS KIT
86201160
Maintenance
Only qualified maintenance personnel are to perform the following repairs.
Pressure Regulator
For best results with the pressure regulator, we recommend that you clean and lubricate the piston and u-cup with Superlube lubricant monthly or when pressure drop seems excessive.
1.
Turn unit off before lubricating.
2.
Remove cap, spring and spring retainer plate.
3.
With fingertips remove piston and u-cup.
4.
Wipe piston and u-cup clean of any film or scale.
5.
Lubricate the piston and u-cup with Superlube.
6.
Reassemble regulator.
7.
With pump ON, re-adjust pressure regulator for normal operation.
Lubricate U-Cup with Superlube Monthly.
R E B U IL D K IT
8.619-924.0
(B L U E 200 P S I)
86345350 DOMINATOR 200 PSI 17
Maintenance
Troubleshooting
PROBLEM
Loss of Power
Electrical shock
Vac motor speed varies or doesn't run
Loss of vacuum
Pump runs no solution
Pump runs, loss of pressure
Pump will not run
Solution hose fitting hard to connect
Carpet not getting clean
Carpet too wet
Carpet browning
Solution not flowing properly
CAUSE
Unit not plugged in
Dead electrical circuit
Faulty power cord
Receptacle not grounded
Internal wiring problem
SOLUTION
Connect unit to 3 prong grounded outlet.
Check building circuit breaker or fuse box.
Replace
Contact an electrician to check building's wiring
Have a trained service technician check machine's wiring
Vacuum circuit breaker tripped
Faulty vacuum motor
Faulty switch
Loose vacuum dome
Crack in dome of poor joint
Reset Breaker
Replace
Replace
Center and seal dome over tank
Replace or repair using acrylic plastic cement only
Lint or dirt clogging vacuum screen
Loose cuffs on vacuum hose
Vac motor seals leaking
Floor tool vac chamber clogged
With power off clean screen
Tighten cuffs turning counterclockwise
Replace
Wash out with hose. Pick lint out with a wire
Replace Vacuum hose damaged
Recovery tank full / Float ball stuck in the up position
Pump inlet screen plugged
Pump not primed
Turn off power, drain recovery tank.
Clean inlet screen
Prime pump with priming hose
Internal or external solution line damaged and leaking
Replace
Internal pump components wearing out Replace, see pump kit components
Check valves in pump head for particles or cuts in seals
Take piston from BPR and lubricate with Superlube. If problem still exists change BPR kit
Faulty switch
Loose wiring
Replace
Repair or replace
Corrosion on fittings.
Severe soil conditions
Over saturation
Leaving carpet too wet
Too much chemical
Solution hose connection
Faulty pump
Faulty floor tool valve / Nozzle
Faulty pump switch
Clean with steel wool. Soak in acetic acid (white vinegar). Lubricate lightly with silicone base lubricant.
Make several passes at right angles to each other. Use a pre-spray.
Adjust solution pressure to lower settings. Make several passes without spray
Check for loss of vac pressure
Check label for correct solution concentration
Check for positive connection
Repair or replace
Repair or replace
Repair
18 86345350 DOMINATOR 200 PSI
PARTS
86345350 DOMINATOR 200 PSI
Control Panel
4
7
11
2
5
1
3
6
8
9
10
11
12
20 86345350 DOMINATOR 200 PSI
Control Panel
REF PART NO.
PRV NO.
QTY
7
8
5
6
3
4
1
2
86230110
86202230
86002370
86002450
86197390
86005700
86276820
86007130
14312
390-09A
20035
22015
31021
57104
70740
72128
9 86002010 14942
10 86323510 -
11 86313020
12 86313030
-
-
DESCRIPTION
2 BREAKER, 7A CIRCUIT
2 WASHER 9/16 S/S USS THICK
1 CLAMP, 7/16 DIA NYLON UL
1 COUPLER, 1/4 QD
1 ELBOW, 1/4NPT 45D STREET
2 NUT, 10-32 HEX W/STAR
6 SCR, 10-32 X 1/2 PTHMS BLK NP
3 SWITCH DPDT 2-POSITION ROCKER
2 BOOT, 3/8 CIRCUIT BREAKER
1 PANEL CONTROL, 200
2 GASKET, .125 T X .25 W X 15.6”
4 GASKET, .125 T X .25 W X 7.2”
SERIAL NO.
FROM
NOTES
86345350 DOMINATOR 200 PSI 21
Electrical
13
10
14
3
1
4
2
11
8
19
9
18
3
17
5
7
16
6
15
12A
12B
22 86345350 DOMINATOR 200 PSI
Electrical
REF PART NO.
PRV NO.
QTY
1 86201510 390-26
2 86005670 57040
3 86005700
4 86273830
57104
70020
5 86006850
6 86256200
7 86161480
8 86010630
70393
73200
-
87013
9 86316460
10 86316540
11 86316700
12A 86199550
12B 86311950
13 86319090
14 86236940
15 86317580
16 86005810
17 86323330
18 86198460
19 86006590
57245
-
20008
70088
-
-
-
-
-
-
-
-
DESCRIPTION
2 SPACER NYLON 1/4ID X 1/2 OD
1 NUT, 1/2 NPT CONDUIT
3 NUT, 10-32 W/STAR WASHER PLTD
2 SCR, 1/4-20 X 1/2 HHCS SS
2 SET SCR, 1/4-20 X 1.25L
1 STRAIN RELIEF, 1/2 NPT FLEX
1 FLTR,INLINE 16A
2 WASHER, 1/4 X 5/8 FLAT SS
1 BRKT, ELECTRICAL
1 CONNECTOR, 5 POS, PUSH WIRE
1 BRKT, CORD STRAIN RELIEF
1 CORDSET, 1.5MM2X25 SAA/3,BLK1A
1 CORDSET, EURO, IPX4,1.5MMX40FT
1 FUSE HOLDER, PANEL MNT
1 FUSE, 2 AMP TYPE MDA
1 BRKT, CORD, BLANK
2 NUT, 1/4-20 NYLOCK
2 WASHER, 1/4" ID X 1.0D FLAT BLK
1 CLAMP, 5/8 NYLON UL/CSA
1 SCREW, 10-32 X 1/2 PPHMS SS NP
SERIAL NO.
FROM
NOTES
AUSTRALIA
EUROPE
86345350 DOMINATOR 200 PSI 23
Frame
2
9
1
11
6
5
3
10
4
7
8
24 86345350 DOMINATOR 200 PSI
Frame
REF PART NO.
PRV NO.
QTY
7
8
5
6
3
4
1
2
86199430
86001660
86005810
86276080
86010630
86005700
86010730
86219480
040-03
41236
57245
70595
87013
57104
87088
41567
9 86309790
10 86312830 -
-
11 86277500 70853
DESCRIPTION
2 CASTER, SWIVEL 4" 250# CPCTY
2 HUBCAP, 5/8 SHAFT
8 NUT, 1/4-20 HEX NYLOCK SS
1 SCR, 10-32 X 1” PPHMS GRN
8 WASHER, 1/4 X 5/8 FLAT SS
2 NUT, 10-32 HEX W/STAR
4 WASHER, 5/8 X 1-3/16 FLAT SS
2 HUBCAP, 9.75" WHEEL
2 WHEEL, 12" X 2.25”
1 FRAME, 5/8" AXLE, DUAL VAC
8 SCR,1/4-20 X 5/8 CARR SS
SERIAL NO.
FROM
NOTES
86345350 DOMINATOR 200 PSI 25
Labels
3
2
26 86345350 DOMINATOR 200 PSI
1
REF PART NO.
PRV NO.
QTY
1 86321760
2 86321770
3 86330730
-
-
-
1
1
1
DESCRIPTION
LABEL, DOM, RH
LABEL, DOM, LH
LABEL, DOM, 150
Labels
SERIAL NO.
FROM
NOTES
86345350 DOMINATOR 200 PSI 27
Pump
1
16
7
19
4
7
24
22
9
6
21
6
20
1
TO SOLUTION TANK
1
17A
17B
2
7
TO CONSOLE
7
11
13
23
25
15
14
15
3
28 86345350 DOMINATOR 200 PSI
23
12
Pump
REF PART NO.
PRV NO.
QTY
7
8
5
6
3
4
1
2
9
10
11 86270990 57245
12 86274450
13 86197760 78308
14 86233410 81270
15 86010630 87013
16 86240500
17A 86200940 65227
17B
18
25
86272730 66017
86200260 151-50C
86323300
86197270 04008
OPEN
86233150 20042
86197360 31016
OPEN
86318390
OPEN
86349970
OPEN
86005710
-
-
-
-
-
-
19 86199580 250-35
20 86321470 -
21 86184900 790601
22 86270850 57026
23 86010650 87018
24 86355740 -
57105
DESCRIPTION
3 PLUG, 1/4 BRASS PIPE
2 HOSE,PULSE 47.0 1/4MPT X 1/4MPT
12 WASHER, 1/4” RUBBER
1 ADPTR, 1/4MPT X 1/4FPT BR
-
2 CLAMP, 3/8 WORM GEAR
4 ELBOW, 1/4 NPT STREET
-
1 HOSE, 1/2" ID WIRE BOUND X 42"
-
4 NUT 10-32 HEX NYLOCK SS
4 SCR, 10-32 X 1.25 HHMS PLTD
1 TEE, 1/4 STREET
1 CLAMP, 3/4 DIA CUSHION .406 DIA
2 WASHER, 1/4 X 5/8 FLAT SS
1 HOSEBARB, 1/4MPT X 3/8 9OD NYL
1 PMP & MTR,200PSI 230V AC NINJA
1 PUMP AND MOTOR 200PSI 230V PM
-
1 D/B BPR 200PSI
1 HOSE, 3/8ID WIRE BOUND X 26"
1 HOSEBARB, 1/4MPT X 1/2H 45 BR
3 NUT, 8-32 HEX NYLOCK
8 WASHER #10 X 9/16 OD
1 BRKT, P/P BPR
1 NUT, 1/4-20 HEX W/STAR WASHER
SERIAL NO.
FROM
NOTES
AUSTRALIA
EUROPE
86345350 DOMINATOR 200 PSI 29
Recovery
18
15
3
19
2
4
8
6
11
14
21
10
12
20
13
10
5
16
17
9
7
1
30 86345350 DOMINATOR 200 PSI
Recovery
REF PART NO.
PRV NO.
QTY DESCRIPTION
7
8
5
6
3
4
1
2
86161460 15-808123 1 DUMP VALVE, 1 1/2
86002620 260-64A 1 ACCESS, COVER CLEAR 6" W/RIM
86197820 31002
86004000 35255
1
1
ELBOW, 1.5 FPT X FS PVC
GASKET, TANK LID
86197040 57264
86273740 70010
86273750 70011
86275800 70546
2
2
4
6
NUT, 5/16-18 HEX ACORN PLTD
SCR, 1/4-20 X 1.50 HHCS SS
SCR, 1/4-20 X 5/8 HHCS SS
SCR, 8 X 3/4 PFHT/S BLK ZINC
9 86010630 87013
10 86010670 87029
11 86323330 -
12 86011020 89202
13 86001350 140390
14 86311510 -
15 86312360
16 86313040
-
-
17 86316710
18 86317230
19 86317720
20 86320790
-
-
-
-
21 86233120 20019
4
6
2
2
2
1
1
1
2
1
2
1
1
WASHER, 1/4 X 5/8 FLAT SS
WASHER, 5/16 X 3/4 SS
WASHER, 1/4 ID X 1.0 OD FLAT BLK
WHEEL, 3" DIA. CUSHION RUBBER
BUSHING, SPANNER .435 X 1.10
ADAPTER, FLOAT 30 DEG, 2
TANK, RECOVERY, TRIMMED
SCRN, FLOAT, SHTOFF, 2
BRKT, CORD, MOUNT
HOSEBARB,1.5MPT X 1.5 W/FLNG
SCR, 5/16-18 X 2.50 BSHCS SS
PIPE ASM, 2", VACUUM
CLAMP, 2.75" WORM GEAR
SERIAL NO.
FROM
NOTES
86345350 DOMINATOR 200 PSI 31
Solution
15
20
9
3
19
17
10
18
1
22
1
4
24
14
7
7
6
14
13
23
8
1
5
2
11
1
22
12
21
16
32 86345350 DOMINATOR 200 PSI
Solution
REF PART NO.
PRV NO.
QTY DESCRIPTION
1 86173640 11-800437 2 ADPT,3/8 BLKHD
2 86233150 20042 2 CLAMP, 3/8 WORM GEAR
3 86238460 36259
4 86197940 40027
2
1
HOOK, STRAP
HOSEBARB, 3/8 MPT X 1/2 HOSE 90°
5 86001550 40043
6 86273740 70010
7 86273830 70020
8 86005810 57245
1
1
11
2
HOSEBARB, 3/8 MPT X 3/8 HOSE 90°
SCR, 1/4-20 X 1.50 HHCS SS
SCR, 1/4-20 X 1/2 HHCS SS
NUT, 1/4-20 HEX NYLOCK SS
9 86324210 -
10 86276160 70604
11 86007970 73864
12 86233410 81270
13 86010670 87029
14 86010630 87013
15 86323330
16 86311990
-
-
4
2
1
2
2
12
2
1
SCR, 1/4-20 X 5/8 BHCS BLK
SCR, 10-32 X 5/8 PPHMS BLK
STRAINER, 3/8 IN. NPT 60 MESH
CLAMP, 3/4 DIA CUSHION .406 DIA
WASHER, 5/16 X 3/4 SS
WASHER, 1/4 X 5/8 FLAT SS
WASHER, 1/4 ID X 1.0 OD FLAT BLK
HINGE, 9.5" LG X .074 THK
17 86312000
18 86312010
19 86321370
20 86297620 -
-
-
-
21 86317560
22 86318790 -
-
23 86242130 48100
24 86324030 -
1 LID, SOLUTION, COVER
1 LID, SOLUTION, HINGE BRKT
1 TANK, SOL, TRIM
2 STRAP, HAND TOOL
1 SPACER, .50 ODX .28 ID X 1.0L
2 WASHER, 1.032ID X 1.5OD X .062THK
2 KNOB, 1/4 HEX PRESS-LOC WING
2 PLATE, MOUNTING, SOLUTION
SERIAL NO.
FROM
NOTES
COMPLETE
86345350 DOMINATOR 200 PSI 33
Vacuum
1
4
12
5
9
13
11
2
7
6
10
3
34
4
8
86345350 DOMINATOR 200 PSI
Vacuum
REF PART NO.
PRV NO.
QTY
1 86005810 57245
2 86274090 70092
3 86233430 81431
4 86010630 87013
5 86278990 87017
6 86311520 -
7 86312990
8 86314710
-
-
9 86317630
10 86318300
11 86348730
-
-
-
86135330
12 86312080
13 86312220
86319020
140688
-
-
-
DESCRIPTION
8 NUT, 1/4-20 HEX NYLOCK SS
5 SCR, 10-32 X 1.5 PPHMS
2 CLAMP, 2.50 WORM GEAR
16 WASHER, 1/4 X 5/8 FLAT SS
8 WASHER, #8 X 3/8 FLAT
1 MANIFOLD, VACUUM, DUAL
1 GASKET, VAC MANIFOLD, DUAL
8 SCR, 1/4-20 X 5.50 HHCS PLT
8 SCR, #8 X 3/4" PPHSMS TYPE AB
1 HOSE, VAC, 2.0 ID X 18.5"L
2 VAC ASM, 2-STAGE, 230V
-
BRUSH SET, 230V VAC MTR
WINDSOR
2 COVER, VAC MOTOR
2 BASE, VAC MOTOR, 2-STAGE
VAC HOUSING, 2-STAGE
SERIAL NO.
FROM
NOTES
INCLUDES 12, 13
86345350 DOMINATOR 200 PSI 35
Wand / Hoses - Optional
1A
1B
36
A
A
SECTION A-A
2
3
4
5
10
8, 9
7
6
15
14
13
12
11
86345350 DOMINATOR 200 PSI
Wand / Hoses - Optional
REF PART NO.
PRV NO.
QTY
1A 86241890 150-50A
1B 86260740 150-50
2 86241500
3 86201720
44010
160-15
4 86002820
5 86201670
6 86136900
7 86202200
27074
160-27
51381
380-39
8 86273810
9 86270770
10 86135760
11 86005580
12 86005590
13 86197390
14 86137260
15 86197320
86000600
-
-
38109
56012
56014
31021
84183
22010
89226
DESCRIPTION
KIT, HOSE ASM 25' HP/1.5"-VAC
HOSE ASM,16.5' HP-M/1/5"-VAC
JET BODY, 1/4MPT
TEE-JET CHECK VALVE FINE
CAP NOZZLE
TEE JET TIP 9501 S/S
SOLUTION LEVER/DIP W/HDWR
WAND GRIP 1 1/2 X 6
SCREW, 1/4-20 X 1 HHCS Ss
NUT, 1/4-20 HEX SS
HANDLE GRIP ASSEMBLY 1.5"T
NIPPLE 1/4 FPT QD
NIPPLE 1/4 CLOSE
ELBOW, 1/4NPT 45D STREET
VALVE, SOLUTION
CONNECTOR, 1/4MPT X 1/4 TUBE
DELUXE PROFESSIONAL WAND
SERIAL NO.
FROM
NOTES
COMPLETE
86345350 DOMINATOR 200 PSI 37
Wiring
-POWER
CORD grn
14awg blu
14awg brn
14awg
230V AC
2
-FILTER
N4 G L2
3U U1
-VACUUM
SWITCH
1
2 5
4
3 6
-PANEL
-VACUUM
SWITCH
1
3
2 5
4
6
13amp
1
2
-CB
1
13amp
2
-CB blk/wt/4
14awg wht/14
14awg yel/12
14awg blu/1
14awg blu/bl/2
14awg
-PUMP
SWITCH
1
3
2 5
4
6 gry/3
14awg
GRN
3
1
1
-F6
2 AMP
2
-WAGO wht/8
14awg
-VACUUM
MOTOR
12
M
1~ wht/7
14awg
-VACUUM
12
M
1~ grn
14awg grn
14awg
-PUMP
12
M
1~ blu
14awg grn
14awg
38 86345350 DOMINATOR 200 PSI
Wiring
REF PART NO.
PRV NO.
QTY
1
2
3
86327730
86349610
86308760 -
-
1
1
DESCRIPTION
HARNESS, MAIN HEATED
WIRE 8" GRN/14 #10 RING X PIG-BK
SPADE
1 WIRE, 4", BLK/14 76050 X 76029
SERIAL NO.
FROM
NOTES
86345350 DOMINATOR 200 PSI 39
Suggested Spare Parts
PART NO.
PRV NO.
DESCRIPTION
86199240 250-33A BPR REPAIR KIT PUMPTEC
86135330 140688 BRUSH SET,230V VAC MTR WINDSOR
86199430 040-03 CASTER SWIVEL 4” 250# CAPACITY
86002620 260-64A ACCESS COVER CLEAR 6” W/RIM
86236940
86225500
86007140
86309790
-
-
72130
-
FUSE, 2 AMP TYPE MDA
VAC MOTOR, 230V 5.7 2ST LNP
SWITCH, SPST 2-POSITION ROCKER
WHEEL, 12” X 2.25”
86001660
86007970
41236 HUBCAP, 5/8” SHAFT
73864 STRAINER 3/8” NPT 60 MESH
86201170 250-79G PUMPTEC KIT C 200PSI (CAM)
86201150 250-79E PUMPTEC KIT A 200PSI (PLUNGER)
86201160 250-79F PUMPTEC KIT B 200PSI (VALVE)
86324290 PRIMING HOSE
86349990
86357300
-
-
CAM AND BRG KIT 200PSI 0100
TERMINAL STRIP, 12 POST IDEAL
SERIAL NO.
FROM
NOTES
EUROPE
AUSTRALIA
CUT TO FIT
40 86345350 DOMINATOR 200 PSI
REF.
NO.
1 N/A
MODEL: SERIAL #
Serial Numbers
86345350 DOMINATOR 200 PSI 41
Notes:
42 86345350 DOMINATOR 200 PSI
