KX-NT343, 346, 366 Quick Reference

KX-NT343, 346, 366 Quick Reference
NT300X_QRG.fm Page 1 Friday, June 22, 2007 10:20 AM
Quick Reference Guide
IP Proprietary Telephone
<KX-NT346>
Model No. KX-NT343/KX-NT346/KX-NT366
Thank you for purchasing an IP Proprietary Telephone (IP-PT).
Please read this manual carefully before using this product and save
this manual for future use. For more details, please refer to the
manuals of the PBX.
Note: In this manual, the suffix of each model number is omitted unless
necessary.
This unit supports the following optional devices and features:
KX-NT343 KX-NT346 KX-NT366*1
Display
3-Line
6-Line
6-Line
Flexible Outside (CO) Line Buttons
24
24
48 (12×4)
Self Labelling
Q
KX-NT303 Add-on 12 key module
Q
Q
KX-NT305 Add-on 60 key module*2
KX-NT307(PSLP1528) Bluetooth
Module
KX-A239AL/BX/X/EJ Optional AC
Adaptor
CODEC
Q
Q
Q
Q
Q
Q
Q
Q
G.729A, G.711, G.722*3
Q: Available
*1 KX-NT366 is only available for KX-TDE100/KX-TDE200.
*2 KX-NT305 is only available for KX-TDE100/KX-TDE200.
*3 G.722 is only available for KX-TDE100/KX-TDE200.
• For information on connecting the KX-NT307, refer to the KX-NT307
Bluetooth® Module Installation Instructions.
This model supports the following PBX versions:
KX-TDA30: PSMPR Software File version 4.0000 or later
KX-TDE100/KX-TDE200: PMMPR Software File version 1.0000 or later
Trademark:
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and
any use of such marks by Matsushita Electric Industrial Co., Ltd. is under
licence.
NT300X_QRG.fm Page 2 Friday, June 22, 2007 10:20 AM
Location of Controls
W
V
A
U
B
C
D
E
F
T
G
H
I
J
S
R
K
L M N
PQ
<KX-NT346>
O
A LCD (Liquid Crystal
Display)
B PAUSE: Used to insert a
pause when storing a
telephone number. This
button is also used for
programming this unit.
C FWD/DND (Call Forwarding/
Do Not Disturb): Used to set
Call Forwarding or Do Not
Disturb on your extension.
D CONF (Conference): Used to
establish a multiple party
conversation.
2
E INTERCOM: Used to make or
receive intercom calls.
F AUTO ANS (Auto Answer)/
MUTE: Used to receive an
incoming call in hands-free
mode or mute the
microphone/handset during a
conversation.
NT300X_QRG.fm Page 3 Friday, June 22, 2007 10:20 AM
Location of Controls
G AUTO DIAL/STORE: Used
for System/Personal Speed
Dialling or storing programme
changes.
H TRANSFER: Used to transfer
a call to another party.
I REDIAL: Used to redial the
last dialled number.
J MESSAGE: Used to leave a
message waiting indication or
call back the party who left
the message waiting
indication.
K Headset Jack
L FLASH/RECALL: Used to
disconnect the current call
and make another call without
hanging up.
M HOLD: Used to place a call
on hold.
N SP-PHONE
(Speakerphone): Used for
performing hands-free
operations.
O NEXT PAGE Key: Used to
switch the page for the Self
Labelling feature. (KX-NT366
only)
P ENTER: Used to assign the
selected item.
Q Microphone: Used for hands
free conversations.
R Navigator Key: Used to
adjust the volume and the
display contrast or select
desired items.
S CANCEL: Used to cancel the
selected item.
T Flexible CO Buttons: Used
to seize an outside line or
perform a feature that has
been assigned to the key.
U LCD Panel: Can be adjusted
to the desired angle.
V Soft Buttons (S1-S4): S1-S4
(located from left to right) are
used to select the item
displayed on the bottom line
of the display.
W Message/Ringer Lamp:
When you receive an
intercom call, the lamp
flashes green, and on an
outside call, the lamp flashes
red. When someone has left
you a message, the lamp
stays on red.
3
NT300X_QRG.fm Page 4 Friday, June 22, 2007 10:20 AM
Settings
Speaker volume While in a hands-free conversation
Handset/Headset While using the handset or
volume*
headset
Ringer volume
LCD Contrast
(for the main
display)
Press Up to increase
While on-hook or receiving a call or Down to decrease
the volume.
While on-hook
PAUSE
PAUSE
Ring Tone
PAUSE
(CO)
PAUSE
OR
INTERCOM
OR
AUTO DIAL
Press 2 times.
STORE
While on-hook
Automatic
PAUSE
OR
AUTO DIAL
Always ON
Always OFF
LCD Backlight
STORE
PAUSE
OR
AUTO DIAL
STORE
* If you hear your own voice through the handset or headset, decrease the
volume.
4
NT300X_QRG.fm Page 5 Friday, June 22, 2007 10:20 AM
Features List
Icon Meanings
(CO)
= Flexible CO button
= Feature number
= Off-hook
= Talk
C. Tone
= On-hook
= Confirmation Tone
Making Calls
To an extension
Calling
To an outside party
extension no.
(CO)
outside phone no.
Redial
REDIAL
Quick Dialling
quick dial no.
One-touch Dialling
To store (KX-NT343/KX-NT346) For storing on a KX-NT366, refer to page 13.
PAUSE
(CO)
AUTO DIAL
desired no.* (max. 32 digits)
STORE
* Enter outside line access
number before outside phone number.
PAUSE
To dial
(CO)
assigned as a One-touch Dialling button
Personal Speed Dialling
To store
personal speed
dial no. (2 digits)
desired no.*
(max. 32 digits)
C. Tone
* Enter outside line access number before
outside phone number.
To dial
AUTO DIAL
personal speed dial no. (2 digits)
STORE
5
NT300X_QRG.fm Page 6 Friday, June 22, 2007 10:20 AM
Features List
System Speed Dialling
To dial
AUTO DIAL
system speed dial no. (3 digits)
STORE
Doorphone Call
doorphone no. (2 digits)
C. Tone
During a Conversation
Call Hold
To hold
To retrieve a call at the holding extension
HOLD
(CO)
C. Tone
/
INTERCOM
To retrieve an outside call from another extension
(CO)
Call Transfer
extension no.
TRANSFER
C. Tone
(CO)
To an extension
outside
phone no.
To an outside party
Useful Features
Multiple Party Conversation
To add other parties during a conversation (i.e., conference)
CONF
C. Tone
desired
phone no.
To leave a conference
CONF
C. Tone
6
CONF
Talk to the
new party.
C. Tone
Talk with
multiple parties.
NT300X_QRG.fm Page 7 Friday, June 22, 2007 10:20 AM
Features List
Setting the Telephone According to Your Needs
Do Not Disturb
Both Calls
Set
Outside Calls
Cancel C. Tone
Intercom Calls
Timed Reminder
To set
12 H
hour/minute
(4 digits)
24 H
AM
PM
hour/minute
(4 digits)
1 time
daily
C. Tone
To cancel
To stop or answer the ring back
INTERCOM
/
C. Tone
Before Leaving Your Desk
Call Forwarding
Both Calls
Outside Calls
Intercom Calls
All calls
extension no.
Busy
No answer
Busy/
No answer
OR
CO line
access no.
outside
phone no.
C. Tone
Cancel
7
NT300X_QRG.fm Page 8 Friday, June 22, 2007 10:20 AM
Features List
Making Use of the Voice Mail Service
Listening to a message
From your own extension
KX-TVM series
Listen to Message
VPS extension no.
Deliver Message
Mailbox Password*
Mailbox Management
* If you have no password, you can skip
the last step.
Automated Attendant
Message Notification
Other Features
From someone else’s extension
End Call
VPS extension no.
KX-TVP series
Listen to Message
mailbox no.
Deliver Message
Mailbox Password*
Check Mailbox Distribution
Automated Attendant
* If you have no password, you can skip
the last step.
Mailbox Management
Other Features
End Call
Leaving a message
VPS extension no.
From your own extension
Mailbox Password*
From someone else’s extension
mailbox no.
Mailbox Password*
* If you have no password, you can skip the last step.
Enter the desired mailbox number
Leave
a message
To send the message immediately
(KX-TVM series)
(KX-TVP series)
To set the delivery time
8
Follow the guidance
NT300X_QRG.fm Page 9 Friday, June 22, 2007 10:20 AM
Features List
During playback
Repeat Voice Guidance
Exit
• Consult your dealer for more details regarding feature numbers.
• It is possible to assign flexible CO buttons as feature buttons.
• Control panel/button names and descriptions can be found in “Location of
Controls” on page 2.
9
NT300X_QRG.fm Page 10 Friday, June 22, 2007 10:20 AM
Accessing Features Using the Display
Using the LCD Display
It is possible to access the following directories, logs, and menus by
pressing left or right on the Navigator Key while this unit is idle:
Extension Number Directory
System Speed Dialling Directory
Personal Speed Dialling Directory
Outgoing Call Log
Incoming Call Log
Entering Characters
You can enter alphabetic characters and digits using the dialling
buttons. Pressing a dialling button repeatedly displays different
characters, as shown in the following tables. While entering
characters, you can move the cursor with the left and right Navigator
keys and delete characters with the TRANSFER button. To toggle
between Table 1 and Table 2, press the Soft button (S1) at any time
while entering characters. For a list of available characters, refer to
the following tables.
Table 1 (Standard mode)
Times
Buttons
10
!
?
"
1
A
B
C
a
D
E
F
d
e
f
3
G
H
I
g
h
i
4
J
K
L
j
k
l
5
M
N
O
m
n
o
6
P
Q
R
S
p
q
r
T
U
V
t
u
v
8
W
X
Y
Z
w
x
y
:
;
0
b
c
(space)
.
,
’
/
+
—
=
<
>
$
%
&
@
(
)
2
s
7
z
9
£
#
NT300X_QRG.fm Page 11 Friday, June 22, 2007 10:20 AM
Accessing Features Using the Display
Table 2 (Option mode)
Times
Buttons
10 11 12 13 14 15
"
ä
ö
ü
1
!
?
A
B
C
a
b
c
À
Á
Â
Ã
Ä
Å
D
E
F
d
e
f
Ð
È
É
Ê
Ë
3
G
H
I
g
h
i
Ì
Í
Î
Ï
4
J
K
L
j
k
l
5
M
N
O
m
n
o
Ñ
Ò
Ó
Ô
Õ
P
Q
R
S
p
q
r
s
Š
ß
7
T
U
V
t
u
v
Ù
Ú
Û
Ü
8
W
X
Y
Z
w
x
y
z
ý
Z
9
(space)
.
,
’
:
;
0
£
#
/
+
—
=
<
>
$
%
&
@
(
)
Ö
Æ
Ç
2
Ø
Œ
6
Table 3 (Option mode when connected to CE model of PBX)
Times
Buttons
10 11 12 13 14 15
!
?
"
ä
ö
ü
1
A
B
C
a
b
c
Á
Â
A
Ä
A
C
Ç
D
E
F
d
e
f
D
Ð
É
E
Ë
e
3
G
H
I
g
h
i
Í
Î
4
J
K
L
j
k
l
L’
L
5
M
N
O
m
n
o
N
N
Ó
Ô
Õ
Ö
6
P
Q
R
S
p
q
r
s
R
R
Š
S
S
T
U
V
t
u
v
T
T
u
Ú
U
Ü
8
W
X
Y
Z
w
x
y
Z
Z
Z
Z
ý
9
(space)
.
,
’
:
;
0
£
#
/
+
—
=
<
>
$
%
&
@
(
)
’
C
2
ß
7
11
NT300X_QRG.fm Page 12 Friday, June 22, 2007 10:20 AM
Self Labelling (KX-NT366 only)
The KX-NT366 IP-PT features 12 flexible buttons, with an LCD
screen next to the buttons. Each item can be named on the LCD
screen through personal or system programming to reflect the
function of its corresponding flexible button. Additionally, the flexible
buttons can be organised into 4 “pages”, allowing you to assign a
total of 48 items to the 12 flexible buttons. You can toggle between
pages by pressing the NEXT PAGE key, as follows:
CO 12
Bank
CO 11
Home
CO 10
London offc.
CO 09
NY offc.
CO 08
Sales
CO 07
Chris Walace
CO 06
Andre Romel
CO 05
Sean Carter
CO 04
Keith Murray
CO 03
Log-in/out
CO 02
LCS
CO 01
CO 13
NEXT PAGE is pressed
• This feature is only available for the KX-TDE100/KX-TDE200.
12
NT300X_QRG.fm Page 13 Friday, June 22, 2007 10:20 AM
Self Labelling (KX-NT366 only)
Storing a One-touch Dialling button, and setting the displayed
text for the Self Labelling LCD Display
PAUSE
(CO)
OR
desired no.*
(max. 32 digits)
AUTO DIAL
STORE
* Enter outside line access number
before outside phone number.
(CO)
desired text
(max.12 characters)
OR
PAUSE
AUTO DIAL
STORE
• Similar to the above procedure, when storing other types of buttons (CO
buttons, feature buttons, etc.), the displayed text for the Self Labelling
LCD Display can be assigned.
Setting the Self Labelling LCD Display contrast levels
PAUSE
OR
OR
AUTO DIAL
AUTO DIAL
STORE
STORE
PAUSE
13
NT300X_QRG.fm Page 14 Friday, June 22, 2007 10:20 AM
Connection
<Back view>
To a PC.
To a Switching Hub.
Optional AC adaptor
(not included).
Clamp
AC adaptor
Headset jack
Do not use a KX-7090 headset.
PC connection
• Use a straight CAT 5 (or higher) Ethernet cable (not included) that is 6.5
mm in diameter or less.
• For further information on the connection to a PC, refer to the
documentation provided for the PBX.
Switching Hub connection
• Use a straight CAT 5 (or higher) Ethernet cable (not included) that is 6.5
mm in diameter or less.
AC adaptor
• Use a Panasonic AC adaptor KX-A239AL (PQLV206AL)/KX-A239BX
(PQLV206CE)/KX-A239X (PQLV206)/KX-A239EJ (PQLV206E).
• The AC adaptor is used as the main disconnect device. Ensure that the
AC outlet is located near the unit and is easily accessible.
14
NT300X_QRG.fm Page 15 Friday, June 22, 2007 10:20 AM
Connection
CAUTION:
When selecting Ethernet cables
Use flexible, high-quality, snagless
(without strain relief) cables. Do not
use cables with coating that may tear
or crack when bent.
To prevent damage to the cables, use
cables* that do not protrude from the
bottom of the base when the
operation board is set to level 1. (For
information on adjusting the angle of
the operation board, refer to
page 16.)
* Use cables as shown.
Ethernet cable
35 mm or less
When connecting cables
Ensure that the Ethernet cables and the AC adaptor cord are
inserted in the grooves, and are clamped to prevent damage to the
connectors. Leave some slack in the AC adaptor cord and the
Ethernet cable connected to the hub.
When connecting headset jack
Ensure that the headset cord is wound around the hook to prevent
damage to the connector.
15
NT300X_QRG.fm Page 16 Friday, June 22, 2007 10:20 AM
Operation Board Angle Adjustment
The angle of the operation board can be set to one
of eight angles (level 1 = 0°, level 8 = 45°).
8
76
5
4
3
2
1
CAUTION:
Hold the operation board until the operation board is secured at the
desired angle. Make sure you do not pinch your fingers when raising
or lowering the operation board.
To raise:
Gently lift the operation board one level at a
time.
To lower:
Raise the operation board to level 8. Next,
with one hand on the base of the unit, lift the
operation board again to release the latch,
then slowly push the operation board down
to level 1. If the operation board cannot be
lowered to level 1, repeat this step.
• When a KX-NT305 is attached to this unit, first
lift the unit’s handset cradle to release the
latch (A), then with one hand on the base of
the KX-NT305, similarly lift its operation board
to release its latch (B).
Locking the Handset Hook
Pull down the handset hook until it locks to prevent the
handset from falling off the handset cradle when the unit
is mounted to a wall or set at a high angle. To temporarily
place the handset down during a conversation, hook it
over the top edge of the unit as shown.
16
NT300X_QRG.fm Page 17 Friday, June 22, 2007 10:20 AM
Installing the KX-NT303/KX-NT305
The KX-NT303/KX-NT305 allow 12/60
additional flexible CO buttons to be added to
this unit. These buttons are used to seize an
outside line, make a call using One-touch
Dialling, or perform a feature that has been
assigned to the key.
<with a KX-NT346>
CAUTION:
Before you install or uninstall the Add-on Key Module, turn off the
unit by disconnecting the AC adaptor (if connected) and the
Ethernet cable connected to the switching hub.
KX-NT303 (For KX-NT343/KX-NT346)
1. Open the cover.
2. Attach the KX-NT303 to your
unit with the screws (included).
3. Plug the flat cable into the
4. Close the cover.
connector (A), then bend the
cable slightly as shown (B).
17
NT300X_QRG.fm Page 18 Friday, June 22, 2007 10:20 AM
Installing the KX-NT303/KX-NT305
KX-NT305 (For KX-NT343/KX-NT346)
1. Open the cover.
2. Attach the KX-NT305 to your
unit with the screws*
(included).
3. Plug the flat cable into the
connector (A), then bend the
cable slightly as shown (B).
4. Close the cover.
* Two types of screws (2 screws of each type) are included with the
KX-NT305, as shown below.
For attaching to the unit
18
For wall mounting
NT300X_QRG.fm Page 19 Friday, June 22, 2007 10:20 AM
Wall Mounting
1. Remove the wall mounting
adaptor from the unit as shown,
set the operation board to level 1,
then connect and secure the
cables.
• The cables can also be run from
the top of the unit (page 14, 15).
2. Attach the wall mounting adaptor
as shown.
Slide the wall
mounting adaptor
up to this point.
• Make sure the cables are not
pinched by the wall mounting
adaptor. When running the cables
from the top of the unit, look
through the opening in the wall
mounting adaptor (A) to confirm
that the cables are not being
pinched.
3. Drive the 2 screws (included) into
the wall either 83 mm or 100 mm
apart, and mount the unit on the
wall.
• You can find a wall mounting
template on page 23.
• Make sure that the wall that the
unit will be attached to is strong
enough to support the unit
(approx. 1.5 kg; approx. 2.5 kg
when the KX-NT305 is attached).
• Make sure the cables are securely
fastened to the wall.
• When this product is no longer in
use, make sure to detach it from
the wall.
83 mm
100 mm
Washer
Drive the screw
to this point.
• If using a KX-NT305, attach the KX-NT305 (page 18) to the unit first, and
perform step 3 only.
• For information on locking the handset hook, refer to page 16.
19
NT300X_QRG.fm Page 20 Friday, June 22, 2007 10:20 AM
Important Information
When using KX-NT300 series IP-PTs, keep the following
conditions in mind.
• If the unit does not operate properly, disconnect the unit from the
Ethernet cable and then connect again.
• If you are having problems making calls, disconnect the Ethernet cable
and connect a known working IP-PT. If the known working IP-PT operates
properly, have the defective IP-PT repaired by an authorised Panasonic
factory service centre. If the known working IP-PT does not operate
properly, check the PBX and the Ethernet cable.
• Wipe the unit with a soft cloth. Do not clean the unit with abrasive
powders or with chemical agents such as benzene or thinner.
• Use only the correct Panasonic handset.
• Do not disassemble this unit. Dangerous electrical shock could result.
The unit must only be disassembled and repaired by qualified service
technicians.
• If damage to the unit exposes any internal parts, immediately disconnect
the cable or cord. If the power is supplied from the network to the IP-PT
[Power-over-Ethernet], disconnect the Ethernet cable. Otherwise,
disconnect the AC adaptor cord. Then return this unit to a service centre.
• Never attempt to insert wires, pins, etc. into the vents or other holes of
this unit.
• This unit is designed to aid the visually handicapped to locate dial keys
and buttons.
Take special care to follow the safety suggestions listed below.
Safety
1) The unit should only be connected to a power supply of the type
described in the Quick Reference Guide or as shown on the label on the
unit.
2) When left unused for a long period of time, the optional AC adaptor
should be unplugged from the AC outlet, if you are using Power-overEthernet, disconnect the Ethernet cable.
Installation
Environment
1) Do not use this unit near water, for example, near a bathtub, washbowl
or sink. Damp basements should also be avoided.
2) Keep the unit away from heating appliances and devices that generate
electrical noise, such as fluorescent lamps, motors and televisions.
These noise sources can interfere with the performance of the unit. It
also should not be placed in rooms where the temperature is less than
5 °C or greater than 40 °C.
20
NT300X_QRG.fm Page 21 Friday, June 22, 2007 10:20 AM
Important Information
Placement
1) Do not place heavy objects on top of this unit.
2) Care should be taken so that objects do not fall onto, and liquids are not
spilled into, the unit. Do not subject this unit to excessive smoke, dust,
moisture, mechanical vibration, shock or direct sunlight.
3) Place the unit on a flat surface.
WARNING:
TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
THIS HANDSET EARPIECE IS MAGNETISED AND MAY RETAIN SMALL
FERROUS OBJECTS.
DISCONNECT THIS UNIT FROM POWER OUTLET/THE ETHERNET
CABLE IF IT EMITS SMOKE, AN ABNORMAL SMELL OR MAKES
UNUSUAL NOISE. THESE CONDITIONS CAN CAUSE FIRE OR
ELECTRIC SHOCK. CONFIRM THAT SMOKE HAS STOPPED AND
CONTACT AN AUTHORISED SERVICE CENTRE.
IMPORTANT NOTICE:
• Under power failure conditions, the IP-PT may not operate. Please
ensure that a separate telephone, not dependent on local power, is
available for use in remote sites in case of emergency.
• For information regarding network setup of the IP-PT such as IP
addresses, please refer to the Installation Manual for the Panasonic PBX.
• If an error message is shown on your display, consult the network
administrator.
• The firmware of the KX-NT343, KX-NT346, and KX-NT366 are protected
by copyright laws and international treaty provisions, and all other
applicable laws. It cannot be reverse engineered, decompiled or
disassembled.
• This equipment shall not be set to make automatic calls to telecom 111
Emergency service.*
Note:
• This device is equipped with pulse dialling while the telecom standard is
DTMF tone dialling. There is no guarantee that the Telecom Lines will
always continue to support pulse dialling.*
* The regulation is applied in New Zealand only.
This unit is capable of being used in conjunction with hearing
aids fitted with inductive coil pick-ups. The handset should be
held as for normal conversation. For operation, the hearing
aid should be set to its “T” position or as directed in the
operating instructions for the hearing aid.
21
NT300X_QRG.fm Page 22 Friday, June 22, 2007 10:20 AM
Important Information
Information on Disposal for Users of Waste Electrical &
Electronic Equipment (private households)
This symbol on the products and/or accompanying documents
means that used electrical and electronic products should not be
mixed with general household waste.
For proper treatment, recovery and recycling, please take these
products to designated collection points, where they will be
accepted on a free of charge basis. Alternatively, in some
countries you may be able to return your products to your local
retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and
prevent any potential negative effects on human health and the environment
which could otherwise arise from inappropriate waste handling. Please
contact your local authority for further details of your nearest designated
collection point.
Penalties may be applicable for incorrect disposal of this waste, in
accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your
dealer or supplier for further information.
Information on Disposal in other Countries outside the
European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or
dealer and ask for the correct method of disposal.
0682
This product is intended to be connected to a Panasonic PBX only.
Panasonic Communications Co., Ltd. declares that this equipment is in
compliance with the essential requirements and other relevant provisions of
Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/
5/EC.
Declarations of Conformity for the relevant Panasonic products described in
this manual are available for download by visiting:
http://www.doc.panasonic.de
Contact:
Panasonic Services Europe
a Division of Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
22
NT300X_QRG.fm Page 23 Friday, June 22, 2007 10:20 AM
One screw here
One screw here
157 mm
100 mm
83 mm
for base unit
If the KX-NT305 is attached to the unit,
leave 157 mm of space between the 2
screws for the unit and the 2 screws for
the KX-NT305, as indicated above. This
space is abbreviated in this template and
must be measured.
2. Hook the unit onto the screw heads.
One screw at either point
for KX-NT305 Add-on 60 Key Module
83 mm
100 mm
WALL MOUNTING TEMPLATE
1. Drive the screws into the wall as
indicated.
Note:
One screw at either point
23
NT300X_QRG.fm Page 24 Friday, June 22, 2007 10:20 AM
Panasonic Communications Co., Ltd.
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka
812-8531, Japan
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and
may be reproduced for internal use only. All other reproduction, in whole or in
part, is prohibited without the written consent of Panasonic Communications
Co., Ltd.
© 2007 Panasonic Communications Co., Ltd. All Rights Reserved.
PSQX4395ZA
KK0707ME0 (X/AL/NZ/CE)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement