section g - Hubbell Wiring Device

section g - Hubbell Wiring Device
SECTION G
Table of Contents
HBL® Watertight
IEC Pin and Sleeve
Product
Products at a Glance
Configurations Chart
IEC Pin and Sleeve
Watertight Devices
Advantage™ Series Switch-Rated Devices
Corrosion Resistant Devices
Data Center Pin and Sleeve
Back Boxes
Accessories
Dimensions
Unfused Circuit-Lock® Mechanical Interlocks
Devices and “Reverse Service”
Accessories and Dimensions
Fused Circuit-Lock® Mechanical Interlocks
Devices and Accessories
Dimensions
www.hubbell-wiring.com
Circuit-Lock® Unfused and
Fused Mechanical Interlocks
Advantage™ Series
Switch-Rated Devices
Page
G-2
G-3
G-6
G-10
G-12
G-13
G-14
G-15
G-16
G-21
G-22
G-25
G-26
Product
Low Profile Pin and Sleeve
Devices and Specifications
Dimensions
IEC Pin and Sleeve Terminal Identification
UL 1686 C1 Insulgrip® Pin and Sleeve
Style I and Style II Devices
“Reverse Service” Style I and II Devices
Back Boxes and Accessories
Dimensions
Insulgrip® Mechanical Interlocks
Style II, Fused and Unfused Devices
Dimensions
Hazardous Location Devices
Mechanical Interlocks and Plugs
Dimensions
®
Wiring Device-Kellems
Page
G-28
G-29
G-30
G-34
G-35
G-36
G-37
G-41
G-42
G-44
G-44
G-1
Pin and Sleeve Devices/Mechanical Interlocks
Products at a Glance
IEC Watertight Devices
• Provide safe and dependable performance
in the most demanding environments
• Heavy duty non-conductive nylon construction
provides impact and corrosion protection
• Thermoset polyester contact carriers withstand
high temperatures and provide resistance to
electrical tracking
Advantage™ Series Pin and Sleeve
Switch-Rated Devices
• Device is similar in size to standard IEC 60309-2
devices. Receptacles mount to standard
Hubbell IEC pin and sleeve back boxes
• Spring-loaded disconnect button oversized
for easy actuation with gloved hands
• Ergonomic design Hubbell puts the
Advantage™ into the palm of your hands
with the easy-to-use leverage grip design
from Hubbell
Corrosion Resistant Devices
• This superior grade of IEC and Insulgrip
devices are ideal for the most demanding
environments
• Nickel-plated brass on the IEC and nickelplated Tellurium copper on the Insulgrip
contacts prevent corrosion and heat rise
Low Profile Devices
• 90° Angled plugs and recessed receptacles
allow for connections in tight spaces
• Cords can be controlled easily along the wall
• The integrated cord grips limit strain on
terminals and prevent strain on plugs and
cables exiting perpendicular from the wall
IEC Pin and Sleeve
Accessories
Back Box
Ordering Information
Description
Nonmetallic Back Box,
20/30A, 1" Hub,
Angled
Back Boxes and Accessories
• A complete line of metallic and nonmetallic back boxes, angle adapters,
closure caps and liquidtight adapters
are available
• These accessories help complement
the line and aid in the installation of the
product
Device Color
Gray
UPC
783585390871
Catalog Number
BB2030N
Listings
UL Raintight and External Icing Test
Specifications
Accessory Item
Back Box
Box Hub Size
Non-Metallic Back Box
15 Degree Angle
1" NPT
Performance
Environmental
Moisture Resistance
IP67 Suitability
Accessories
Recepatcle/Inlet Accommodation 16A, 20A, 30A & 32A IEC Pin & Sleeve
Recepatcle/Inlet Accommodation Watertight Safety-Shroud®
Resources
Customer Use Drawing
eCatalog
Insulgrip® NEMA 4X UL 1686 C1 Devices
• Metallic where you want it and non-metallic
where you need it
• This tough product line is NEMA 4X rated
for use in the harshest environments
• Devices are fully interchangeable with other
manufacturers of UL1686 C1 devices
G-2
®
Wiring Device-Kellems
Dimensions in Inches (mm)
Hubbell Wiring Device-Kellems • Hubbell Incorporated (Delaware) • 40 Waterview Drive • Shelton, CT 06484
Phone (800) 288-6000 • Fax (800) 255-1031 • Specifications subject to change without notice.
eSpec Sheets Available Online
• Product Features
• Specifications
• Dimensions
• Performance
• Complementary Products
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
IEC Configurations Chart
Singly Rated Configurations
Voltage
Hubbell Pin and Sleeve products are designed and
manufactured to meet the International Standard IEC
60309-1 and IEC 60309-2. This device standard calls out
a singly rated, non-interchangeable configuration for every
voltage and type of service throughout the world. Pin and
sleeve device housings are color coded by voltage rating.
The voltage is determined by the location of the female
ground contact relative to the housing keyway. Simply by
manufacturing the device with a ground contact in a certain
“clock” position, the device will be rated for a particular
voltage system. The diagram shows the keying position and
the color coding that is associated with each voltage.
3Ø 250V
2P
Gr ole
ou
11 12 1
10
2
9
3
4
8
7 6 5
380415V
250V
DC 380V 50Hz
440V 60Hz
125V
AC
550V
DC
480V
AC
400V DC
3Ø
480V AC
Color
re
Wi
3 ing
nd
3ØY
120/208V
ire
W
4 ing
d
440-460V
(60Hz)
3
Gr Pol
ou e
n
125/250V
AC
ire
W
5 ng
di
4
Gr Pol
ou e
n
Rated Voltage
100V - 130V
125V/250V
200V - 250V
277V
380V - 480V
500V - 690V
277V
AC
250V
AC
380-415V
AC
3ØY
277/480V
3Ø
600V AC
3ØY
347/600V
200/346V AC
240/415V AC
Typical IEC Pin and Sleeve Catalog Number
HBL4100C12W
HBL 4 100 C 12 W
Hubbell Catalog Number
4 Wire
100 Amp
Watertight
Female Ground Sleeve at “12” O’Clock (125/250V)
“C” Connector
Explanation
1 (HBL) Designates 2 First Digit 3 Next Series Of Digits 4 Letter 5
Hubbell Catalog
3-3 wire
Preceding a letter
P-Plug
Number
4-4 wire
20-20 Amp R-Receptacle
5-5 wire
30-30 Amp
C-Connector
60-60 Amp
B-Inlet
100-100 Amp
MI-Mechanical
Interlock
MIF-Mechanical
Interlock Fused
eSpec Sheets Available Online
®
6 Letter: W
Last Digit(s) After the letter. This denotes
Watertight
the position of the ground
sleeve and the assigned
voltage in the receptacle as
it relates to the hours of the
clock. This is done to eliminate
interchangeability between
devices with different voltages.
Wiring Device-Kellems
G-3
Pin and Sleeve Devices/Mechanical Interlocks
Features and Benefits
RoHS
IP67
SUITABILITY
Watertight Devices
Hubbell’s IEC 60309 Pin and Sleeve plugs, connectors, inlets and receptacles
are the highest performing products available. The HBL® series of IEC pin and
sleeve were designed for the demanding North American market. Hubbell was
the first and is still only manufacturer of IEC 60309 devices in the USA and
have a full list of innovative features.
G-4
Housing Design
• Insulated non-metallic housing, super
tough, non-conductive and chemical
resistant for heavy duty industrial
environments
• IEC pin and sleeve devices are color
coded by voltage for easy identification
• Self-closing gasketed cover, detents
into position to fully close automatically
Liquidtight Conduit Adapters
• Machined aluminum adapters are
available to provide a means for
attaching flexible liquidtight metal
conduit to rear of Hubbell Pin and
Sleeve plug or connector
Powerful Mechanical Cord Grip
• Hubbell’s design incorporates two
molded-in teeth to securely grip
the outer cable jacket, and internal
conductors to prevent slippage and
strain on terminations
• Captive barrel nuts ease assembly
and allow higher tightening torque
for maximum cord retention
Sequential Contact Engagement
• Ground makes first and breaks last.
Neutral makes second and breaks
second (to prevent a momentary
over-voltage on components
connected phase to neutral)
• Phase contacts make last and
break first
Watertight Cord Entrance
• The tapered bore entrance creates
high compression forces on sealing
gland, providing a watertight seal
around cord
• Individual solid neoprene glands
are supplied to match a full range
of cord sizes and assure watertight
performance
Multi-Contact Spring
• (60/63 and 100/125 Amp) Recessed
within the female sleeve, provides and
maintains high unit pressure on mating
pins to minimize temperature rise
• Broaches oxide film to achieve low
resistance contact for cooler operation
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Features and Benefits
RoHS
IP67
SUITABILITY
Watertight Devices
The IEC line of plugs and connectors are made with a rugged super tough,
one-piece housing. The thermoset polyester contact carrier provides a high
resistance to electrical tracking. They withstand higher temperatures which
may result from overload or arcing. The heavy-duty, external cord grip
provides superior strain relief on the conductors. Hubbell’s horsepower rated
plugs and receptacles meet NEC 430.109(F) requirements and recognizes
as an approved disconnecting/“line of sight” disconnecting means.
Housing Design
• Rugged one-piece housing, thick
wall construction protects internal
components, eliminates joints
preventing infiltration of contaminants
• Amperage/voltage rating and catalog
number molded in housing for easy
identification
Shrouded Pins
• Super tough plug shroud protects pins
from deforming from physical abuse
• Protects the user from the possibility of
touching live contacts during insertion
and withdrawal of mating parts
• Solid one-piece pins, machined from
solid brass for longer life and reliable
electrical contact
Safety
• Lockout/Tagout, tapered opening on
plug shroud accommodates up to
³⁄₈ inch (9.7mm) lock shackle diameter
Thermoset Polyester Contact Carrier
• Molded thermoset polyester provides
high resistance to electrical tracking
• Withstands higher temperatures which
may result from overload or arcing
• Thermoset properties provide dimensional
stability for this critical assembly
Cord Grips
• Heavy duty external cord grips provide
maximum cord retention to maintain
secure terminations
Swivel Pressure Pads
• 16/20 and 30/32 Amp devices feature
patented swiveling pressure pad
terminal screws and prevent damage
to conductor strands. 60/63 and
100/125 Amp devices feature large
hex-head stainless steel screws which
provide higher torque levels for secure
terminations
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-5
IP67
Pin and Sleeve Devices/Mechanical Interlocks
Rating
Poles
and
Amps Wires
Configuration
Recep./
Plug/
Conn.
Inlet
Watertight Devices
Plug
Connector
SUITABILITY
Accessories
Inlet
Back Boxes
Non­­-Metallic Metallic*
AC Voltage
Receptacle
16 2P 3W
100-130V
HBL316R4W
HBL316P4W
HBL316C4W
HBL316B4W† BB2030N
2P 3W
220-240V
HBL316R6W HBL316P6W
HBL316C6W
HBL316B6W
3P 4W
380-415V
HBL416R6W
HBL416P6W
HBL416C6W
HBL416B6W† BB2030N
4P 5W
220/380V
240/415V
HBL516R6W HBL516P6W
HBL516C6W
HBL516B6W
20 2P 3W
125V
HBL320R4W HBL320P4W
HBL320C4W
HBL320B4W BB2030N
2P 3W
250V
HBL320R6W HBL320P6W
HBL320C6W
HBL320B6W BB2030N
2P 3W
480V
HBL320R7W HBL320P7W
HBL320C7W
HBL320B7W BB2030N
3P 4W
125/250V
HBL420R12W HBL420P12W HBL420C12W HBL420B12W BB2030N
3P 4W
3Ø 250V
HBL420R9W HBL420P9W
HBL420C9W
HBL420B9W BB2030N
3P 4W
3Ø 480V
HBL420R7W HBL420P7W
HBL420C7W
HBL420B7W BB2030N
3P 4W
3Ø 600V
HBL420R5W HBL420P5W
HBL420C5W
HBL420B5W BB2030N
4P 5W
3ØY
120/208V
HBL520R9W HBL520P9W
HBL520C9W
HBL520B9W BB2030N
4P 5W
3ØY
277/480V
HBL520R7W HBL520P7W
HBL520C7W
HBL520B7W BB2030N
4P 5W
3ØY
347/600V
HBL520R5W HBL520P5W
HBL520C5W
HBL520B5W BB2030N
30 2P 3W
125V
HBL330R4W HBL330P4W
HBL330C4W
HBL330B4W BB2030N
2P 3W
250V
HBL330R6W HBL330P6W
HBL330C6W
HBL330B6W BB2030N
2P 3W
480V
HBL330R7W HBL330P7W
HBL330C7W
HBL330B7W BB2030N
3P 4W
125/250V
HBL430R12W HBL430P12W HBL430C12W HBL430B12W BB2030N
3P 4W
3Ø 250V
HBL430R9W HBL430P9W
HBL430C9W
HBL430B9W BB2030N
3P 4W
3Ø 480V
HBL430R7W HBL430P7W
HBL430C7W
HBL430B7W BB2030N
3P 4W
3Ø 600V
HBL430R5W HBL430P5W
HBL430C5W
HBL430B5W BB2030N
4P 5W
3ØY
120/208V
HBL530R9W HBL530P9W
HBL530C9W
HBL530B9W BB2030N
4P 5W
3ØY
277/480V
HBL530R7W HBL530P7W
HBL530C7W
HBL530B7W BB2030N
4P 5W
3ØY
347/600V
HBL530R5W HBL530P5W
HBL530C5W
HBL530B5W BB2030N
32 2P 3W
100-130V
HBL332R4W† HBL332P4W† HBL332C4W† HBL332B4W† BB2030N
2P 3W
220-240V
HBL332R6W HBL332P6W
HBL332C6W
HBL332B6W BB2030N
3P 4W
380-415V
HBL432R6W HBL432P6W
HBL432C6W
HBL432B6W BB2030N
3P 4W
380V 50Hz
440V 60Hz
HBL432R3W HBL432P3W
HBL432C3W
HBL432B3W† BB2030N
4P 5W
220/380V
240/415V
HBL532R6W HBL532P6W
HBL532C6W
HBL532B6W BB2030N
BB2030N
BB2030N
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
BB201W
BB301W
RoHS
Replacement Interiors
Closure
Caps
Recep./
Conn.
Plug/
Inlet
PC320
IN320BF
IN320BM
PC320
IN320BF
IN320BM
PC420
IN420DF
IN420DM
PC520
IN520EF† IN520EM
PC320
IN320AF
IN320AM
PC320
IN320BF
IN320BM
PC320
IN320BF
IN320BM
PC420
IN420CF
IN420CM
PC420
IN420DF
IN420DM
PC420
IN420DF
IN420DM
PC420
IN420DF
IN420DM
PC520
IN520EF† IN520EM
PC520
IN520EF† IN520EM
PC520
IN520EF† IN520EM
PC3430 IN330AF
IN330AM†
PC3430 IN330BF
IN330BM
PC3430 IN330BF
IN330BM
PC3430 IN430CF
IN430CM
PC3430 IN430DF
IN430DM
PC3430 IN430DF
IN430DM
PC3430 IN430DF
IN430DM
PC530
IN530EF
IN530EM
PC530
IN530EF
IN530EM
PC530
IN530EF
IN530EM
PC3430 IN330BF
IN330BM
PC3430 IN330BF
IN330BM
PC3430 IN430DF
IN430DM
PC3430 IN430DF
IN430DM
PC530
IN530EM
IN530EF
Note: See page G-12 and G-13 for back boxes and accessories, G-14 and G-15 for product dimensions, G-16 and G-17 for product specifications and HP ratings.
See page G-13 for closure caps, purchased separately. PC320, PC420, PC520, PC3430, PC530 are not UL or CSA.
*These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
†Consult factory.
G-6
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Rating
Poles
and
Amps Wires
60
63
Configuration
Recep./
Plug/
Conn.
Inlet
Watertight Devices
AC Voltage
Receptacle
Plug
Connector
Accessories
Inlet
125V
HBL360R4W
HBL360P4W
HBL360C4W
HBL360B4W
BB60N
2P 3W
250V
HBL360R6W
HBL360P6W
HBL360C6W
HBL360B6W
BB60N
2P 3W
480V
HBL360R7W
HBL360P7W
HBL360C7W
HBL360B7W
BB60N
3P 4W
125/250V
HBL460R12W HBL460P12W HBL460C12W HBL460B12W BB60N
3P 4W
3Ø 250V
HBL460R9W
HBL460P9W
HBL460C9W
HBL460B9W
BB60N
3P 4W
3Ø 480V
HBL460R7W
HBL460P7W
HBL460C7W
HBL460B7W
BB60N
3P 4W
3Ø 600V
HBL460R5W
4P 5W
3ØY
120/208V
4P 5W
3ØY
277/480V
4P 5W
3ØY
347/600V
2P 3W
220-240V
3P 4W
380-415V
4P 5W
220/380V
240/415V
BB601W
BB602W
BB601W
BB602W
BB601W
BB602W
BB601W
BB602W
BB601W
BB602W
BB601W
BB602W
BB601W
BB602W
BB601W
HBL560R9W HBL560P9W HBL560C9W HBL560B9W BB60N
BB602W
BB601W
HBL560R7W HBL560P7W HBL560C7W HBL560B7W BB60N
BB602W
BB601W
HBL560R5W HBL560P5W HBL560C5W HBL560B5W BB60N
BB602W
BB601W
HBL363R6W HBL363P6W HBL363C6W HBL363B6W BB60N
BB602W
BB601W
HBL463R6W HBL463P6W HBL463C6W HBL463B6W BB60N
BB602W
BB601W
HBL563R6W HBL563P6W HBL563C6W HBL563B6W BB60N
BB602W
BB1001W
HBL3100R4W HBL3100P4W HBL3100C4W HBL3100B4W BB100N
BB1002W
BB1001W
HBL3100R6W HBL3100P6W HBL3100C6W HBL3100B6W BB100N
BB1002W
BB1001W
HBL3100R7W HBL3100P7W HBL3100C7W HBL3100B7W BB100N
BB1002W
HBL460C5W
HBL460B5W
BB60N
RoHS
Replacement Interiors
Back Boxes
Closure
Non­­-Metallic Metallic* Caps
2P 3W
HBL460P5W
IP67
SUITABILITY
Recep./
Conn.
Plug/
Inlet
PC60
IN360AF
IN360AM
PC60
IN360BF
IN360BM†
PC60
IN360BF
IN360BM†
PC60
IN460CF
IN460CM
PC60
IN460DF
IN460DM
PC60
IN460DF
IN460DM
PC60
IN460DF
IN460DM
PC60
IN560EF
IN560EM†
PC60
IN560EF
IN560EM†
PC60
IN560EF
IN560EM†
PC60
IN360BFS
IN360BMS†
PC60
IN460DFS
IN460DMS
PC60
IN560EFS† IN560EMS
PC100
IN3100AF
IN3100AM
PC100
IN3100BF
IN3100BM†
PC100
IN3100BF
IN3100BM†
100 2P 3W
125V
2P 3W
250V
2P 3W
480V
3P 4W
125/250V
HBL4100R12W HBL4100P12W HBL4100C12W HBL4100B12W BB100N
BB1001W
PC100
BB1002W
IN4100CF† IN4100CM
3P 4W
3Ø 250V
HBL4100R9W HBL4100P9W HBL4100C9W HBL4100B9W BB100N
BB1001W
PC100
BB1002W
IN4100DF
IN4100DM
3P 4W
3Ø 480V
HBL4100R7W HBL4100P7W HBL4100C7W HBL4100B7W BB100N
BB1001W
PC100
BB1002W
IN4100DF
IN4100DM
3P 4W
3Ø 600V
HBL4100R5W HBL4100P5W HBL4100C5W HBL4100B5W BB100N
BB1001W
PC100
BB1002W
IN4100DF
IN4100DM
4P 5W
3ØY
120/208V
HBL5100R9W HBL5100P9W* HBL5100C9W HBL5100B9W BB100N
PC100
IN5100EF
IN5100EM
4P 5W
3ØY
277/480V
HBL5100R7W HBL5100P7W HBL5100C7W HBL5100B7W BB100N
PC100
IN5100EF
IN5100EM
4P 5W
3ØY
347/600V
HBL5100R5W HBL5100P5W HBL5100C5W HBL5100B5W BB100N
PC100
IN5100EF
IN5100EM
125 2P 3W
220-240V
HBL3125R6W HBL3125P6W HBL3125C6W HBL3125B6W BB100N
PC100
IN3100BFS† IN3100BMS†
3P 4W
380-415V
HBL4125R6W HBL4125P6W HBL4125C6W HBL4125B6W BB100N
PC100
IN4100DFS IN4100DMS
4P 5W
220/380V
240/415V
HBL5125R6W HBL5125P6W HBL5125C6W HBL5125B6W BB100N
PC100
IN5100EFS IN5100EMS
BB1001W
BB1002W
BB1001W
BB1002W
BB1001W
BB1002W
BB1001W
BB1002W
BB1001W
BB1002W
BB1001W
BB1002W
Note: See page G-12 and G-13 for back boxes and accessories, G-14 and G-15 for product dimensions, G-16 and G-17 for product specifications and HP ratings.
All 63A and all 125A devices have pilot pins or contacts.
See page G-13 for closure caps, purchased separately. PC60 and PC100 are not UL or CSA.
See page G-14 for additional information on short housing plug. IP22 suitability - length 8.30" (210.8).
*These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
†Consult factory.
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-7
Pin and Sleeve Devices/Mechanical Interlocks
Hubbell’s Pin and Sleeve connections have always been
safe – that hasn’t changed. The Advantage™ series
simply has more… Advantages.
IEC 60309 Singularly Rated Device
Mates with existing installed base of IEC 60309-2 pin and sleeve devices.
Color coded by voltage for easy identification of mating devices.
Superior Water Ingress Protection
IP69k
UL witnessed IP69k and UL Type 4X and 12. Device is built to
withstand wet and harsh environments.
Power Indicating LED Lights PWR
Highly visible and long lasting green LED lights on both sides of
the device provide visual verification of power when connected.
Continuous Ground Engagement
Unswitched feed-through ground pin is first-to-make and
last-to-break followed by switched neutral and phase contact(s).
Permanent Labelless Markings
Product ratings are laser-marked into the device and will not
wash off for easy permanent identification.
Sleek and Modern Design
The ergonomic device is easy to keep clean making it ideal for
hygienic food processing facilities.
The Advantage™ Series has a UL witnessed IP69k
and 4X,12 environmental rating, two power-indicating
LEDs, continuous ground engagement, labelless laser
markings and a compact and ergonomic design.
G-8
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
IP69k
Features and Benefits
Advantage™ Series Pin and Sleeve Switch-Rated
Hubbell Wiring Device-Kellems Advantage™ Series Pin and Sleeve Switch-Rated
Devices are IEC 60309-2 compatible devices that are approved as a disconnecting
means for motor and branch circuits. Compact design, this device is similar in size
to standard IEC 60309-2 devices. Robust and durable housing, UV-stabilized,
impact and corrosion-resistant PBT housing is designed to withstand harsh
industrial environments. Stainless steel hardware provides superior corrosion
resistance in wet and harsh environments Receptacles mount to standard
Hubbell IEC Pin and Sleeve back boxes.
Housing Design
• Rugged one-piece housing, thick
wall construction protects internal
components, eliminates joints
preventing infiltration of contaminants
• IEC pin and sleeve devices are color
coded by voltage for easy identification
Heavy Duty External Cord Grips
• Provides maximum cord retention to
maintain unstressed terminations
• Pocketed recess for screws deters
slippage of the screwdriver and are
conveniently located on the same side
for easy installation
Safety
• Ergonomic design puts the
Advantage™ into the palm of your
hands with the easy-to-use leverage
grip design from Hubbell
Spring-Loaded Cover
• Spring-loaded to the open position,
reminding users that the cover must be
secured to ensure maximum ingress
protection
• Impact resistant cover arm compact
and durable internal swing arm is fully
shrouded protecting it from damage
Spring-Loaded Disconnect Button
• Oversized for easy actuation with
gloved hands
Power Indicating LED Lights
• Provides visual verification of power
when connected
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-9
Pin and Sleeve Devices/Mechanical Interlocks
Rating
IP69k
Pin and Sleeve Devices
Configuration
Poles
and Recep./
Plug/
Inlet
Amps Wires Conn.
AC Voltage
Connector
Receptacle
Accessories
HP
Mating Plug**
HBLS330R4W
2
HBLS330P4W
HBL330B4W
IP67 Inlet
BB2030N
Back Boxes
PC3430
Closure Caps
HBL332B4W
BB2030N
PC3430
30
2P 3W
125V
HBLS330C4W
32
2P 3W
100-130V
HBLS332C4W
HBLS332R4W
2
HBLS332P4W
30
2P 3W
250V
HBLS330C6W*
HBLS330R6W*
5
HBLS330P6W* HBL330B6W*
BB2030N
PC3430
32
2P 3W
220-240V
30
2P 3W
480V
HBLS330C7W
HBLS330R7W
10
HBLS330P7W
BB2030N
PC3430
30
3P 4W
125/250V
HBLS430C12W
HBLS430R12W
2
HBLS430P12W HBL430B12W
BB2030N
PC3430
30/32 3P 4W
3Ø 250V
HBLS430C9W*
HBLS430R9W*
10
HBLS430P9W* HBL430B9W*
BB2030N
PC3430
HBL330B7W
30
3P 4W
3Ø 480V
HBLS430C7W
HBLS430R7W
20
HBLS430P7W
HBL430B7W
BB2030N
PC3430
30
3P 4W
3Ø 600V
HBLS430C5W
HBLS430R5W
30
HBLS430P5W
HBL430B5W
BB2030N
PC3430
380-415V
HBLS430C6W*
HBLS430R6W*
7.5
HBLS430P6W* HBL430B6W*
BB2030N
PC3430
30/32 3P 4W
32
3P 4W
380-440V
HBLS432C3W
HBLS432R3W
10
HBLS432P3W
HBL432B3W
BB2030N
PC3430
30
4P 5W
3ØY 347/600V
HBLS530C5W
HBLS530R5W
30
HBLS530P5W
HBL530B5W
BB2030N
PC530
30
4P 5W
HBLS530C6W*
HBLS530R6W*
7.5
HBLS530P6W* HBL530B6W*
BB2030N
PC530
32
4P 5W
200/346240/415V
220/380V
240/415V
30
4P 5W
3ØY 277/480V
HBLS530C7W
HBLS530R7W
20
HBLS530P7W
BB2030N
PC530
30/32 4P 5W
3ØY 120/208V
HBLS530C9W*
HBLS530R9W*
10
HBLS530P9W* HBL530B9W*
BB2030N
PC530
HBL530B7W
Note: *Certain IEC configurations allow for a single product to be certified as both a North American (Series 2) and International amperage (Series 1). These products are marked
accordingly with both the UL Listing and UL Classified markings.
**Mating plug required to maintain 4X/IP69k ratings when used with ADVANTAGE™ Series Connections.
ADVANTAGE™ Series Receptacles have the same mounting pattern as standard Hubbell IEC pin and sleeve.
Materials
Specifications
Part
Material
Connector
Receptacle
Cover
Valox
X
X
Cover Gasket
Neporene
X
X
Housing
Valox
X
X
X
Gasket
Santoprene
X
X
X
X
X
Phase, Ground Sleeves Brass
X
X
Sleeve Springs
X
X
Female Contact Carrier Nylon
Male Contact Carrier
Thermoset
Plug/Inlet
X
Beryllium Copper
with Silver Plating
Pins
Brass
Glands
Solid Neoprene
X
X
Cord Clamps
Valox
X
X
Clamp Nut
Nickel-Plated Brass
X
X
Screws
Stainless Steel
(300 Series)
X
Locking Ring
Valox
Switch Contacts
Laminated Silver
G-10
X
X
X
X
X
®
Temperature Rise
< 30°C
Dielectric Voltage
Min 2,200V AC
Electrical Life
Min 6,000 Cycles at rated switch load
(p.f.= .75-.80)
Max Working Voltage
600V AC
Current Interrupting
Certified for current interrupting at full
rated current and voltage
Horsepower Locked
Rotor Test
50 Operations at 600% of full load motor
current (p.f.= .40-.50)
Short Circuit
100kA when protected by 100A Class J
fuse or 125A RK1 fuse
Endurance
Min 10,000 mating cycles
Flammability
HB or Better per UL 94 or CSA C22.2
No. 0.17
Operating Temperature Max Continuous +75°C; Min continous
-40°C
Environmental
Type 4X, 12 and IP69k
UV Resistance
All materials are UV stabilized
X
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Rating
IP69k
Pin and Sleeve Devices
Poles
Configuration
and Recep./
Plug/
Amps Wires Conn.
Inlet
AC Voltage
Connector
Receptacle
Accessories
HP
Mating Plug**
Inlet**
HBLS360C4W
HBLS360R4W
HBLS360B4W
HBLS360C6W*
Back Boxes
Closure Caps
3
HBLS360P4W
BB60N
PC60
HBLS360R6W*
7.5
HBLS360P6W* HBLS360B6W* BB60N
PC60
60
2P 3W
125V
60
2P 3W
250V
63
2P 3W
220-240V
60
2P 3W
480V
HBLS360C7W
HBLS360R7W
15
HBLS360P7W
BB60N
PC60
60
3P 4W
125/250V
HBLS460C12W
HBLS460R12W
30
HBLS460P12W HBLS460B12W BB60N
PC60
60/63 3P 4W
3Ø 250V
HBLS460C9W*
HBLS460R9W*
10
HBLS460P9W* HBLS460B9W* BB60N
PC60
HBLS360B7W
60
3P 4W
3Ø 480V
HBLS460C7W
HBLS460R7W
30
HBLS460P7W
HBLS460B7W
BB60N
PC60
60
3P 4W
3Ø 600V
HBLS460C5W
HBLS460R5W
40
HBLS460P5W
HBLS460B5W
BB60N
PC60
380-415V
HBLS460C6W*
HBLS460R6W*
10
HBLS460P6W* HBLS460B6W* BB60N
PC60
3ØY 347/600V
HBLS560C5W
HBLS560R5W
40
HBLS560P5W
BB60N
PC60
200/346240/415V
HBLS560C6W*
HBLS560R6W*
10
HBLS560P6W* HBLS560B6W* BB60N
PC60
4P 5W
3ØY 277/480V
HBLS560C7W
HBLS560R7W
30
HBLS560P7W
BB60N
PC60
60/63 4P 5W
3ØY 120/208V
HBLS560C9W*
HBLS560R9W*
10
HBLS560P9W* HBLS560B9W* BB60N
PC60
60/63 3P 4W
60
4P 5W
60/63 4P 5W
60
HBLS560B5W
HBLS560B7W
Note: *Certain IEC configurations allow for a single product to be certified as both a North American (Series 2) and International amperage (Series 1). These products are marked
accordingly with both the UL Listing and UL Classified markings.
**Mating plug or inlet required to maintain 4X/IP69k ratings when used with ADVANTAGE™ Series Connections.
ADVANTAGE™ Series Receptacles have the same mounting pattern as standard Hubbell IEC pin and sleeve.
Just add a "P" suffix for Pilot pin for 60 amp devices.
Optional Pilot Pin Available on All 60A Devices:
The Pilot Pin is smaller than the ground and phase pins and are designed to make after main
and break before main breaks. This pin can be used to communicate with auxiliary devices
within your facility. They are “Break before main break” and by design are the last contact in
the sequence to make and first to break.
Rating
Pin and Sleeve Devices
Amp
Poles/
Wires
AC Voltage
60/63
3P 4W
3Ø 250V
Connector
with Pilot Sleeve
Receptacle
with Pilot Sleeve
Plug
with Pilot Pin
Inlet
with Pilot Pin
HBLS460C9WP*
HBLS460R9WP*
HBLS460P9WP*
HBLS460B9WP*
Note: *Just add a "P" suffix for Pilot pin for 60 amp devices.
Dimensions
Ø .22" (5.59) X 4
5.09"
(129.3)
5.17"
(131.3)
1.85"
(47.0)
12.22"
(310.4)
4.77"
(121.2)
3.88" (98.6)
4.52" (114.8)
Dimensions in Inches (mm)
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-11
Pin and Sleeve Devices/Mechanical Interlocks
IP67
Corrosion Resistant Devices that Withstand the Most Abusive Environments
SUITABILITY
RoHS
Hubbell offers a superior grade of 100A IEC Pin and Sleeve designed for use in the most demanding environments. These
devices feature nickel plated solid brass pins for long life and reliable electrical contact in the most corrosive environments.
They have a high visibility yellow supertough nylon housing. The heavy duty external cord clamps provide maximum cord
retention to maintain secure terminations. The screws and fasteners are made from stainless steel.
• Food Processing
• Water Treatment
• Meat Packing
• Agriculture
• Factory
• Washdown
• Construction
• Outdoor Entertainment
• Temporary Power
Standard Service
Rating
Amps
100
Poles
And
Wires
Configuration
Recep./
Conn.
Plug
Watertight Devices
AC Voltage
Receptacle
Plug
Accessories
Connector
Back Boxes
Non­­-Metallic Metallic*
Closure
Caps
3P 4W
125/250V
M4100R12
M4100P12
M4100C12
BB100N
BB1001W
BB1002W
PC100
4P 5W
3ØY
120/208V
M5100R9
M5100P9
M5100C9
BB100N
BB1001W
BB1002W
PC100
4P 5W
3ØY
277/480V
M5100R7
M5100P7
M5100C7
BB100N
BB1001W
BB1002W
PC100
"Reverse Service"
Rating
Amps
100
Poles
And
Wires
Configuration
Conn.
Inlet
Watertight Devices
Plug
Accessories
Connector
Back Boxes
Non­­-Metallic Metallic*
Closure
Caps
AC Voltage
Inlet
3P 4W
125/250V
M4100B12R
—
M4100C12R
BB100N
BB1001W
BB1002W
PC100
4P 5W
3ØY
120/208V
M5100B9R
—
M5100C9R
BB100N
BB1001W
BB1002W
PC100
4P 5W
3ØY
277/480V
M5100B7R
—
M5100C7R
BB100N
BB1001W
BB1002W
PC100
Note: *These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
See page Y-17 for corrosion resistant cord sets.
G-12
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
IP67
Data Center DC Rated Pin and Sleeve Devices
RoHS
SUITABILITY
In today’s environmentally conscious world, energy savings is a pinnacle part of going green.
DC (Direct Current) is being used to reduce power consumption and decrease the amount of
infrastructure needed to energize specific types of data center equipment. Electrical devices
provide a means of connecting DC power.
Hubbell is the first manufacturer to introduce a series of IEC Pin and Sleeve devices
configured for the UL1686 eight o’clock ground position for DC voltage (Disconnecting use
only). Hubbell’s IEC DC rated pin and sleeve line has been qualified by UL to the requirements
of DC voltage. The thermoset polyester contact carrier provide high resistance to electrical
tracking, it withstands higher temperatures for this type of demanding application. The solid
one-piece pins are machined from solid brass for longer life and reliable electrical contact.
In addition, the heavy-duty external cord grips provide maximum cord retention to maintain
secure terminations. Finally, the super tough, color coded, non-conductive V-0 rated Valox®
housing is heavy duty for safety and protecting the internal components.
Rating
Amps
30
60
100
Poles
And
Wires
Configuration
Recep./
Conn.
Plug
Watertight Devices
DC Voltage
Receptacle
Plug
Connector
2P 3W
550V
HBL330R8WDC
HBL330P8V0DC
HBL330C8V0DC
2P 3W
550V
HBL360R8WDC*
HBL360P8V0DC
HBL360C8V0DC
2P 3W
550V
HBL3100R8WDC
HBL3100P8V0DC
HBL3100C8V0DC
4P 5W
400V
HBL5100R8WDC
HBL5100P8V0DC
HBL5100C8V0DC
Note: *Inlet available - HBL360B8WDC.
IP67
RoHS
SUITABILITY
Dual Certified Pin and Sleeve Devices
Hubbell’s dual certified pin and sleeve devices are ideal for the data center and high tech server industry. They are UL Listed
to UL1682 for the North American market and are TUV Rheinland Certified for the European and International market.
Customers can use the same plug and connector for multiple electrical configurations. They reduce the number of SKU’s
end users have to use if they sell to both domestic and overseas customers. These devices are IP67 rated, RoHs compliant
and showcase all the inherent safety benefits of their V-0 rated Valox® housing and internal components.
Rating
Amps
30/32
60/63
Poles
And
Wires
Configuration
Recep./
Conn.
Plug
Watertight Devices
AC Voltage
Receptacle
Plug
Connector
Inlet
3P 4W
380-415V
HBL430R6V02
HBL430P6V02
HBL430C6V02
HBL430B6V02
4P 5W
200/346V
240/415V
HBL530R6V02
HBL530P6V02
HBL530C6V02
HBL530B6V02
3P 4W
380-415V
HBL460R6V02
HBL460P6V02
HBL460C6V02
HBL460B6V02
4P 5W
200/346V
240/415V
HBL560R6V02
HBL560P6V02
HBL560C6V02
HBL560B6V02
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-13
Pin and Sleeve Devices/Mechanical Interlocks
RoHS
Back Boxes
Hubbell manufactures an extensive line of back boxes for use with IEC Pin and Sleeve devices. Each
back box is designed to give the user the maximum amount of wiring room while achieving grounding
to metallic conduit. Hubbell back boxes are available in non-metallic and cast metal versions.
Non-Metallic 15º Angle Back Box
BB60N
Description
NPT Hub Size*
Back box for 16, 20, 30 and 32A devices.
1"
Catalog Number
BB2030N
Back box for 60 and 63A devices.
1¼"
BB60N
Back box for 100 and 125A devices.
1½"
BB100N
Note: *Hub is not included; order one of the following Raco® part numbers: 1 in. = 1704, 1¼ in. = 1705, 1½ in. = 1706.
These boxes meets IP67 requirement and Type 4X requirements when installed with a watertight conduit hub.
Metallic 15º Angle Back Boxand Adapter**
Description
BB601W
NPT Hub Size
Back box for 16, 20, 30 and 32A devices.
Back box for 60 and 63A devices.
Back box for 100 and 125A devices.
Catalog Number
¾"
BB201W
1"
BB301W
1¼"
BB601W
1½"
BB602W
1½"
BB1001W
2"
BB1002W
AA6010015
Angle adapter only for 60,63,100 and 125A devices.
Note: **These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
FW6010055
Metallic 55º Angle Back Box and Adapter**
Description
NPT Hub Size
Feed-thru box back box and adapter for 16, 20, 30 and 32A devices.
1"
AB203055
AA203055
Angle adapter only.
Back box and adapter for 60, 63, 100 and 125A devices.
Catalog Number
1½"
FW6010055
AA6010055
Angle adapter only.
Note: **These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
FT202W
Metallic Feed-Thru Back Box**
Description
NPT Hub Size
Feed-thru box for 16, 20, 30 and 32A devices.
Catalog Number
¾"
FT202W
1"
FT302W
Note: **These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
Metallic Four-Way 15º Angle Back Box**
FW60100
Description
NPT Hub Size
Four-way box for 60, 63, 100 and 125A devices.
1½"
Catalog Number
FW60100
Note: **These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
Straight Wall Box Adapter
HBL2030AP
Description
Catalog Number
Adapts 16, 20, 30 and 32A Watertight IEC Pin and Sleeve devices to
2-gang, device boxes and FD boxes.
HBL2030AP
Angle Wall Box Adapter
AA2030PS
G-14
Description
Catalog Number
Adapts 16, 20, 30 and 32A Watertight IEC Pin and Sleeve devices to
standard wall boxes.
AA2030PS
Note: Adapts 20 and 30A Watertight Pin and Sleeve receptacle to single, 2-gang standard wall box and 4 or 4¹¹⁄₁₆⁄₁₆ inch
square for non-watertight applications.
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Accessories
Closure Caps
Cap assemblies provide watertight sealing to a disconnected male IEC Pin and Sleeve plug or inlet.
Manufactured of the same tough non-metallic material as the watertight IEC Pin and Sleeve devices
for corrosion and abuse resistance.
Description
Catalog Number
Fits all 16 and 20A, 3 wire plugs and inlets.
Fits all 16 and 20A, 4 wire plugs and inlets.
Fits all 16 and 20A, 5 wire plugs and inlets.
Fits all 30 and 32A, 3 and 4 wire plugs and inlets.
Fits all 30 and 32A, 5 wire plugs and inlets.
Fits all 60 and 63A plugs and inlets.
Fits all 100 and 125A plugs and inlets.
PC320
PC420
PC520
PC3430
PC530
PC60
PC100
PC3430
Cover Assemblies
Replacement cover assemblies for use with watertight connector bodies and receptacles.
Kit contains cover, arm assembly and installation tool.
Description
Catalog Number
Fits all 16 and 20A, 3 wire watertight female devices.
Fits all 16 and 20A, 4 wire watertight female devices.
Fits all 16 and 20A, 5 wire watertight female devices.
Fits all 30 and 32A, 3 and 4 wire watertight female devices.
Fits all 30 and 32A, 5 wire watertight female devices.
Fits all 60 and 63A watertight female devices.
Fits all 100 and 125A watertight female devices.
CA320
CA420
CA520
CA3430
CA530
CA60
CA100
CA3430
Cord Clamp and Locking Ring
Replacement cord clamp and locking ring for use with IEC plugs, connectors and inlets.
Description
Cord Clamp and
Locking Ring
Locking Ring Only
Fits all 16 and 20A, 3 wire plugs, connectors and inlets.
Fits all 16 and 20A, 4 wire plugs, connectors and inlets.
Fits all 16 and 20A, 5 wire plugs, connectors and inlets.
Fits all 30 and 32A, 3 and 4 wire plugs, connectors and inlets.
Fits all 30 and 32A, 5 wire plugs, connectors and inlets.
Fits all 60 and 63A plugs, connectors and inlets.
Fits all 100 and 125A plugs, connectors and inlets.
CC320
CC420
CC520†
CC3430
CC530†
CC60
CC100
LR320*
LR420*
LR520*
LR3430*
LR530*
LR60*
LR100*
CC3430
LR3430
Note: *Locking Ring only for plugs and inlets.
†Consult factory.
Liquidtight Adapters
Machined aluminum adapters are available to provide a means for attaching flexible liquidtight metal
conduit to rear of a Hubbell Pin and Sleeve plug or connector. To install, remove cord grip and two
gland cap screws. Use screws to attach adapter. Kellems® liquidtight conduit connectors are available
to control arc of bend and to prevent conduit pull-out where vibration, motion or strain is present. These
grips interface directly with Hubbell’s liquidtight adapters and are available in a wide variety of NPT sizes
and configurations. Consult your local code grounding requirements before using liquidtight adapters.
Rating of Hubbell
Pin and Sleeve Device
Liquidtight
Conduit Size
Hubbell Liquidtight
Adapter
Optional Kellems
Liquidtight Conduit Grip
16 and 20 Amp
3 and 4 Wire
½" NPT
¾" NPT
½" NPT
¾" NPT
1" NPT
½" NPT
¾" NPT
1" NPT
1¼" NPT
1¼" NPT
1½" NPT
SAA12
SAA34
SAB12
SAB34
SAB100
SAC12
SAC34
SAC100
SAC125
SAD125
SAD150
074093402
074093403
074093402
074093403
074093404
074093402
074093403
074093404
074093405
074093405
074093406
16 and 20 Amp 5 wire
and 30 and 32 Amp
3 and 4 wire
30 and 32 Amp 5 wire
and 60 and 63 Amp (all)
100 and 125 Amp (all)
eSpec Sheets Available Online
®
SAB34
Wiring Device-Kellems
074093403
G-15
Pin and Sleeve Devices/Mechanical Interlocks
Plug Dimensions
Plug
Type
B
A
Short Housing Plug
B
A
B
Cord Grip Range
HBL320P
6.61" (167.8)
2.87" (73.0)
.330"-.830" (8.4-21.1)
HBL420P
7.00" (177.8)
3.19" (81.0)
.330"-.830" (8.4-21.1)
HBL520P
7.65" (194.3)
3.50" (89.0)
.330"-.830" (8.4-21.1)
HBL330P
8.05" (204.5) 3.74" (95.0)
.375"-1.250" (9.5-31.8)
HBL430P
8.05" (204.5) 3.74" (95.0)
.375"-1.250" (9.5-31.8)
HBL530P
8.54" (216.9) 4.02" (102.0) .500"-1.450" (12.7-36.8)
HBL360P, HBL460P, HBL560P
10.15" (257.8) 4.49" (114.0)
.500"-1.450" (12.7-36.8)
HBL3100P, HBL4100P, M4100P,
HBL5100P, M5100P
12.63" (320.8) 4.92" (125.0)
1.065"-1.940" (27.1-49.3)
Short Housing Plug Dimensions
Type
A
HBL5100P9WSH
A
B
Cord Grip Range
8.30" (210.82) 4.92" (125.0)
1.065"-1.940" (27.1-49.3)
Connector Body Dimensions
Connector Body
Type
B
A
Inlet
B
D
A
B
Cord Grip Range
HBL320C
7.49" (190.3)
3.33" (84.6)
.330"-.830" (8.4-21.1)
HBL420C
7.90" (200.6) 3.66" (93.0)
.330"-.830" (8.4-21.1)
HBL520C
8.54" (216.9) 3.94" (100.0) .330"-.830" (8.4-21.1)
HBL330C
9.05" (229.9) 4.27" (108.5) .375"-1.250" (9.5-31.8)
HBL430C
9.05" (229.9) 4.27" (108.5) .375"-1.250" (9.5-31.8)
HBL530C
9.68" (245.8) 4.70" (119.5)
.500"-1.450" (12.7-36.8)
HBL360C, HBL460C, HBL560C
11.15" (283.2) 5.10" (129.5)
.500"-1.450" (12.7-36.8)
HBL3100C, HBL4100C, M4100C,
HBL5100C, M5100C
13.57" (344.7) 5.71" (145)
1.065"-1.940" (27.1-49.3)
Inlet Dimensions
Type
A
C
E
F
⁷⁄₃₂" (5.5) Dia. (4 Holes)
Receptacle
A
B
C
D
E
F
HBL320B
2.54" (64.5)
1.85" (47.0)
1.14" (29.0)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL420B
2.54" (64.5)
2.11" (53.6)
1.14" (29.0)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL520B
2.54" (64.5)
2.41" (61.2)
1.14" (29.0)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL330B
2.99" (76.0)
2.49" (63.2)
1.04" (26.5)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL430B
2.99" (76.0)
2.49" (63.2)
1.04" (26.5)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL530B
2.99" (76.0)
2.75" (69.9)
1.04" (26.5)
2.80" (71.0)
3.75" (95.3)
3.13" (79.5)
HBL360B,
4.04" (102.6)
HBL460B, HBL560B
2.97" (75.5)
1.18" (30.0)
3.46" (88.0)
4.50" (114.3)
3.88" (98.5)
HBL3100B,
4.53" (115)
HBL4100B, M4100B,
HBL5100B, M5100B
3.44" (87.5)
1.95" (49.5)
3.94" (100.0) 5.50" (139.7) 4.88" (124.0)
Receptacle Dimensions
A
D
B
E
F
⁷⁄₃₂" (5.5) Dia. (4 Holes)
Type
A
B
C
D
E
F
HBL320R
3.33" (84.5)
2.78" (70.6)
1.02" (26.0)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL420R
3.66" (93.0)
2.78" (70.6)
1.02" (26.0)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL520R
3.94" (100.0) 2.78" (70.6)
1.02" (26.0)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
C HBL330R
4.27" (108.5) 3.09" (78.5)
1.16" (29.5)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL430R
4.27" (108.5) 3.09" (78.5)
1.16" (29.5)
2.72" (69.0)
3.75" (95.3)
3.13" (79.5)
HBL530R
4.70" (119.4)
3.09" (78.5)
1.16" (29.5)
2.83" (71.9)
3.75" (95.3)
3.13" (79.5)
HBL360R,
5.10" (129.5)
HBL460R, HBL560R
4.07" (103.4)
1.69" (43.0)
3.46" (88.0)
4.50" (114.3)
3.88" (98.6)
HBL3100R,
5.71" (145)
HBL4100R, M4100R,
HBL5100R, M5100R
4.23" (107.4)
2.46" (62.5)
3.95" (100.3) 5.50" (139.7) 4.88" (123.9)
Note: 20, 30, 60 and 100A devices are dimensionally equivalent to 16, 32, 63 and 125A devices, respectively.
Dimensions in Inches (mm)
G-16
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Non-Metallic 15º Angle Back Box
E
NPT
Hub
Size
A
Inch
(mm)
B
Inch
(mm)
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
F
Inch
(mm)
Cubic
Inch
Capacity
Catalog
Number
1"
5.67"
(144.0)
4.44"
(112.8)
4.05"
(102.9)
3.91"
(99.3)
2.35"
(59.7)
4.92"
(125.0)
30.00"
BB2030N
Back box for 60
& 63A devices.
1¼" 7.76"
(197.0)
5.16"
(131.0)
5.87"
(149.0)
4.72"
(120.0)
2.99"
(76.0)
6.94"
(176.0)
70.00"
BB60N
Back box for 100
& 125A devices.
1½" 8.21"
6.23"
(209.0) (158.0)
6.31"
(160.3)
5.71"
(145.0)
3.99"
(101.0)
7.41"
(188.0)
120.00"
BB100N
Description
Back box for 16, 20,
30 & 32A devices.
F
C
A
15°
B
D
Non-Metallic Angle Box
Note: *Hub is not included; order one of the following Raco® part numbers: 1 inch = 1704, 1¼ inch = 1705, 1½ inch = 1706.
These boxes meet IP67 requirement and Type 4X requirements when installed with a watertight conduit hub.
Metallic 15º Angle Back Box
E
A
Inch
(mm)
B
Inch
(mm)
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
F
Inch
(mm)
Cubic
Inch
Capacity
Catalog
Number
Back box for 16, 20,
30 & 32A devices.
¾"
5.12"
(130.2)
4.00"
(101.6)
4.19"
(106.4)
3.75"
(95.3)
3.00"
(76.2)
4.00"
(101.6)
30.00"
BB201W
Back box for 16, 20,
30 & 32A devices.
1"
5.12"
(130.2)
4.00"
(101.6)
4.19"
(106.4)
3.75"
(95.3)
3.00"
(76.2)
4.00"
(101.6)
30.00"
BB301W
Back box for 60
& 63A devices.
1¼" 7.25"
(184.2)
5.25"
(133.4)
6.00"
(152.4)
4.50"
(114.3)
3.75"
(95.3)
6.19"
(157.2)
80.00"
BB601W
Back box for 60
& 63A devices.
1½" 7.25"
(184.2)
5.25"
(133.4)
6.00"
(152.4)
4.50"
(114.3)
3.75"
(95.3)
6.19"
(157.2)
80.00"
BB602W
Back box for 100
&125A devices.
1½" 8.12"
6.75"
(206.4) (171.5)
6.88"
(174.6)
5.50"
(139.7)
4.75"
(120.7)
6.94"
(176.2)
130.00"
BB1001W
6.88"
(174.6)
5.50"
(139.7)
4.75"
(120.7)
6.94"
(176.2)
130.00"
BB1002W
Back box for 100
& 125A devices.
2"
8.12"
6.75"
(206.4) (171.5)
Description
B
Inch
(mm)
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
F
Inch
(mm)
Cubic
Inch
Capacity
6.80"
(172.4)
6.60"
(167.0)
5.63"
(142.9)
4.50"
(114.3)
3.74"
(95.0)
–
42.27"
AB203055
Angle adapter for 16,
20, 30 & 32A devices.
–
4.89"
(124.3)
3.33"
(84.6)
4.29"
(109.0)
3.75"
(95.2)
2.50"
(63.5)
–
25.00"
AA203055
8.00"
7.75"
(202.9) (196.8)
6.90"
(174.8)
6.00"
(152.4)
–
100.00"
FW6010055
4.48"
(113.7)
6.00"
(152.4)
6.75"
(171.4)
6.00"
(152.4)
–
79.00"
AA6010055
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
–
6.75"
(171.4)
D
Metallic 15º Angle Box
Catalog
Number
1"
Angle adapter for 60,
63, 100 & 125A devices.
15°
E
C
55°
A
Inch
(mm)
1½" 8.50"
(215.9)
F
B
A
Feed-thru box and
angle adapter for 16,
20, 30 & 32A devices.
Back box and angle
adapter for 60, 63,
100 & 125A devices.
C
B
Metallic 55º Angle Back Box and Adapter
NPT
Hub
Size
A
41
Description
NPT
Hub
Size
D
Metallic 55º Angle Box
E
48 CU. IN.
C
A
F
Metallic Feed-Thru Back Box
Description
NPT
Hub
Size
A
Inch
(mm)
B
Inch
(mm)
F
Inch
(mm)
Cubic
Inch
Capacity
Catalog
Number
Feed-thru box for 16,
20, 30 & 32A devices.
¾"
8.25"
3.06"
(209.6) (77.8)
7.14"
(181.4)
4.50"
(114.3)
3.75"
(95.3)
3.13"
(79.5)
48.00"
FT202W
Feed-thru box for 16,
20, 30 & 32A devices.
1"
8.25"
3.06"
(209.6) (77.8)
7.14"
(181.4)
4.50"
(114.3)
3.75"
(95.3)
3.13"
(79.5)
48.00"
FT302W
B
D
Metallic Feed-Thru Box
D
E
B
Metallic Four-Way 15º Angle Back Box
B
Inch
(mm)
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
Four-way box for 60,
1½" 8.75"
9.75"
63, 100 & 125A devices.
(222.3) (247.7)
7.75"
(196.9)
6.75"
(171.5)
6.00"
(152.4)
Description
NPT
Hub
Size
A
Inch
(mm)
F
Inch
(mm)
Cubic
Inch
Capacity
Catalog
Number
–
210.00"
FW60100
Note: These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
These boxes withstand a 500-hour salt spray test as well as UL rain tight and external icing test.
A
C
Metallic Four-Way Angle Box
Dimensions in Inches (mm)
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-17
Pin and Sleeve Devices/Mechanical Interlocks
Watertight Materials
PartMaterial
Inlet
Housing Locking Ring
Mounting Flange
Mounting Screws
Contact Carrier Retainer Ground, Phase Pins Terminal Screws
Assembly Screws (2)
Gaskets
Zytel® 101 Nylon*
Reinforced Thermoplastic Polyester
Zytel® 101 Nylon
Stainless Steel (300 Series)
High-Impact Thermoset
High-Impact Thermoset
Brass (M-Series - Nickel-plated brass)
Stainless Steel (300 Series)
Stainless Steel (300 Series)
Solid Neoprene
Connector Body
HousingZytel® ST801 Nylon
Cord Clamps
Reinforced Thermoplastic Polyester
Glands
Solid Neoprene
Cover Arms
Reinforced Thermoplastic Polyester
Arm Springs
Stainless Steel (17-7 type)
CoversReinforced Thermoplastic Polyester
Cover Screw
Nickel-plated brass
Rotating Sealing Disc
Polycarbonate
Gaskets
Solid Neoprene
Contact Carrier
High-Impact Thermoset
Retainer
High-Impact Thermoset
Phase, Ground Sleeves
Brass
Sleeve Spring
20A and 30A Stainless Steel (300 Series); others are Beryllium Copper
multi-contact inserts with silver plating
Terminal Screws
Stainless Steel (300 Series)
Assembly Screws
Stainless Steel (300 Series)
Listed to standard UL1682/CSA C22.2
No. 182.1-02, Plugs, Receptacles and
cable connectors of the Pin and Sleeve
Type.
UL Classified to IEC Standards 603091 (Plugs, Socket Outlets, and Couplers
for Industrial Purposes) for Series I
(European) rated voltages and services.
When used with cord, these devices
require no further investigation by UL
for equipment Classification to IEC 435
or IEC 380.
Plug
HousingZytel® ST801 Nylon
Locking Ring
Reinforced Thermoplastic Polyester
Sealing Gasket
Solid Neoprene
Cord Clamp
Reinforced Thermoplastic Polyester
Gland Cap
Reinforced Thermoplastic Polyester
Gland
Solid Neoprene
Cord Clamp Screws
Stainless Steel (300 Series)
Clamp Nut
Nickel-Plated Brass
Gland Clamp Screws
Stainless Steel (300 Series)
Contact Carrier
High-Impact Thermoset
Retainer
High-Impact Thermoset
Ground, Phase Pins
Brass (M-Series - Nickel-plated brass)
Terminal Screws
Stainless Steel (300 Series)
Assembly Screws
Stainless Steel (300 Series)
Receptacle
HousingZytel® 101 Nylon
Mounting Flange
Zytel® 101 Nylon
Arm Spring
Stainless Steel (17-7 type)
Cover Arm
Reinforced Thermoplastic Polyester
CoverReinforced Thermoplastic Polyester
Cover Screw
Nickel-plated brass
Rotating Sealing Disc
Polycarbonate
Gaskets
Solid Neoprene
Mounting Screws
Stainless Steel (300 Series)
Terminal Screws
Stainless Steel (300 Series)
Phase, Ground Sleeves
Brass
Sleeve Spring
20A and 30A Stainless Steel (300 Series); others are Beryllium Copper multi-contact inserts with silver plating
Specifications
Typical Specification
Manufacturer’s Identification
Description
Type
Rating
Configuration
Certification
Hubbell HBL520P9W
Plug, Power Supply
3 Pole + Neutral + Earth
20A, 120/208V AC, 3 Phase WYE
UL 1686 C2, IEC 60309-2, Clock Position 9, Watertight
UL Listed, File E146032 Receptacles and Inlets, E146033 Plugs and Connectors,
UL Standard UL1682 and UL 1686C2, CSA Certified File LR280C for Plugs,
Connectors Inlets and LR285C for Receptacle CSA StandardC22.2 No. 182.1,
UL Classified to IEC 60309-1 IEC 60309-2
Note: *All devices on page G-11 have Valox® housings.
® Zytel is registered trademark of E.I. DuPont.
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
G-18
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Performance
Electrical
Dielectric Withstand Voltage
Max. Working Voltage
Current Interrupting
Temperature Rise
Endurance
3000V AC.
600V RMS (i.e., minimum creepage distance 10 millimeters, minimum clearance 8 millimeters, per IEC 60309-1
for devices rated over 500V).
Certified for current interrupting at full rated current (Except DC rated devices).
Max. 30°C temperature rise at full rated current after 50 cycles of overload at 150% of rated current at a power
factor of 75%.
5,000 connect and disconnect cycles with load for 16A and 20A, 1,000 cycles with load and 1,000 cycles without
load for 30A, 32A, 60A and 63A, and 250 cycles with load and 250 cycles without load for 100A and 125A.
Mechanical
Impact Resistance
Cord Grip Cable Retention
Cord Accommodation
Terminal Identification
Product Identification
Per CSA C22.2 No. 182.1 / UL1682.
Per CSA C22.2 No. 182.1 / UL1682.
Round portable service cords of diameters commensurate with the device rating as defined in UL Standard 62,
CSA C22.2 No. 49 and the harmonized <HAR> European Standards.
Terminals identified in accordance with North American and IEC conventions.
Identification and ratings are a permanent part of the device housing.
Environmental
Moisture Resistance
Ingress Protection
Flammability
Operating Temperatures
Watertight per IEC 60309-1.
IP67 Suitability.
HB or better per UL 94 or CSA C22.2 No. 0.17.
Maximum Continuous 75°C; Minimum - 40°C without impact.
Materials
HousingsNylon.
All Other Materials
Resistant to corrosion and chemical attack.
Note: Specification sheets for all other Pin and Sleeve catalog numbers are available upon request.
Horsepower Ratings for IEC Pin and Sleeve
AC Voltage Rating
Horsepower
Catalog Number
3Ø 250
2
HBL420R9W
HBL420P9W
HBL420C9W
HBL420B9W
3Ø 480
5
HBL420R7W
HBL420P7W
HBL420C7W
HBL420B7W
3Ø 600
7.5
HBL420R5W
HBL420P5W
HBL420C5W
HBL420B5W
3ØY 120/208
.5
HBL520R9W
HBL520P9W
HBL520C9W
HBL520B9W
3ØY 277/480
5
HBL520R7W
HBL520P7W
HBL520C7W
HBL520B7W
3ØY 347/600
7.5
HBL520R5W
HBL520P5W
HBL520C5W
HBL520B5W
3Ø 250
3
HBL430R9W
HBL430P9W
HBL430C9W
HBL430B9W
3Ø 480
7.5
HBL430R7W
HBL430P7W
HBL430C7W
HBL430B7W
3Ø 600
10
HBL430R5W
HBL430P5W
HBL430C5W
HBL430B5W
3ØY 120/208
2
HBL530R9W
HBL530P9W
HBL530C9W
HBL530B9W
3ØY 277/480
7.5
HBL530R7W
HBL530P7W
HBL530C7W
HBL530B7W
3ØY 347/600
10
HBL530R5W
HBL530P5W
HBL530C5W
HBL530B5W
3Ø 250
5
HBL460R9W
HBL460P9W
HBL460C9W
HBL460B9W
3Ø 480
10
HBL460R7W
HBL460P7W
HBL460C7W
HBL460B7W
3Ø 600
15
HBL460R5W
HBL460P5W
HBL460C5W
HBL460B5W
3ØY 120/208
3
HBL560R9W
HBL560P9W
HBL560C9W
HBL560B9W
3ØY 277/480
10
HBL560R7W
HBL560P7W
HBL560C7W
HBL560B7W
3ØY 347/600
15
HBL560R5W
HBL560P5W
HBL560C5W
HBL560B5W
3Ø 250
10
HBL4100R9W
HBL4100P9W
HBL4100C9W
HBL4100B9W
3Ø 480
30
HBL4100R7W
HBL4100P7W
HBL4100C7W
HBL4100B7W
3Ø 600
30
HBL4100R5W
HBL4100P5W
HBL4100C5W
HBL4100B5W
3ØY 120/208
10
HBL5100R9W
HBL5100P9W
HBL5100C9W
HBL5100B9W
3ØY 277/480
30
HBL5100R7W
HBL5100P7W
HBL5100C7W
HBL5100B7W
3ØY 347/600
30
HBL5100R5W
HBL5100P5W
HBL5100C5W
HBL5100B5W
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-19
Pin and Sleeve Devices/Mechanical Interlocks
Features and Benefits
IP67
SUITABILITY
Unfused Circuit-Lock® Pin and Sleeve Mechanical Interlocks
The National Electrical Code (NEC®) requires a separate disconnect means
within sight of all motor loads. The NEC requires the disconnecting means in a
motor-circuit be listed as “Suitable as Motor Disconnect” if the motor is rated
greater than 2 HP.
Hubbell’s revolutionary Circuit-Lock interlock incorporates the disconnect switch
and receptacle in one compact, non-metallic and economical unit. Removing
the plug and locking it out provides a visual means of verifying equipment has
been disconnected. All Circuit-Lock mechanical interlocks can be locked out as
a method of compliance with the OSHA Lockout/Tagout regulation.
The switch cannot be turned ON until the plug is completely engaged, and the
plug cannot be removed until the switch is turned OFF. At the same time, it
eliminates the possibility of making or breaking the circuit under load or making
a casual or “lazy” connection. The non-metallic enclosure can be connected to
the metallic conduit and not interfere with the ground continuity.
In addition, these horsepower rated units are durable, watertight and easy to
install. And they are compatible with IEC 60309-2 plugs. These Circuit-Lock
units are available in 20, 30, 60 and 100A models, and in 3, 4 and 5 wire
configurations that are designed to the IEC 60309-1 and 60309-2 standards.
Hubbell’s Circuit-Lock Mechanical Interlocks are also available in “Reverse
Service” versions. These units incorporate the disconnect switch and reverse
service receptacle (inlet) in one compact, non-metallic and economical unit.
These units are available in 30, 60 and 100A models, 4 wire configurations.
HBL430MI7W
Housing Design
• Insulated non-metallic housing, super
tough, non-conductive and chemical
resistant for heavy duty industrial
environments
• IEC pin and sleeve devices are color
coded by voltage for easy identification
• Self-closing gasketed cover, detents
into position to fully close automatically
Interior Design
• Large gears enclosed in a gear box
assembled on one plane to eliminate
possible gear jumping
• Horsepower rated disconnect switch
handles large motor loads
• DIN rail mounted switch for easy
installation and replacement
Safety
• Lockable handle to meet OSHA
Lockout/Tagout regulations
• Two-stage interlocking mechanism to
help defeat tampering
• Watertight conduit hub and grounding
plate for use on metallic conduit
(IP67 suitability)
• Captured neoprene gasket for a
watertight seal
Liftcover
• Replaceable spring-loaded liftcover
with gasket for a watertight seal
• Pre-wired IEC Pin and Sleeve
receptacle
• Reverse service has dependable solid
brass pins for longer life and reliable
electrical contact
Identification
• Color coded rating pad and
receptacle mount to signify voltage
Installation
• Comes with brass inserts and stainless
steel screws for higher torque and
better sealing
• Three molded-in conduit drill points
are located on top, bottom and back
surface of enclosure
• Adjustable mounting feet are ductile to
allow mounting on irregular surfaces
NEC® is a registered trademark of the National Fire Protection Association (NFPA).
G-20
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Enclosure Type 4X, 12
IP67
SUITABILITY
Unfused Circuit-Lock® Devices
Rating
Reverse Service
Amps
Poles
and
Wires
20
3P 4W
120/240V
HBL420MI12W
HBL420P12W
—
—
3P 4W
3Ø 240V
HBL420MI9W
HBL420P9W
—
—
3P 4W
3Ø 480V
HBL420MI7W
HBL420P7W
—
—
3P 4W
3Ø 600V
HBL420MI5W
HBL420P5W
—
—
2P 3W
120V
HBL330MI4W
HBL330P4W
—
—
2P 3W
240V
HBL330MI6W
HBL330P6W
—
—
2P 3W
480V
HBL330MI7W
HBL330P7W
—
—
3P 4W
120/240V
HBL430MI12W
HBL430P12W
—
—
3P 4W
3Ø 240V
HBL430MI9W
HBL430P9W
HBL430MI9WR
HBL430P9WR
3P 4W
3Ø 480V
HBL430MI7W
HBL430P7W
HBL430MI7WR
HBL430P7WR
3P 4W
3Ø 600V
HBL430MI5W
HBL430P5W
HBL430MI5WR
HBL430P5WR
4P 5W
3ØY 120/208V
HBL530MI9W
HBL530P9W
—
—
4P 5W
3ØY 277/480V
HBL530MI7W
HBL530P7W
—
—
4P 5W
3ØY 347/600V
HBL530MI5W
HBL530P5W
—
—
32
3P 4W
380V 50HZ440V 60Hz
HBL432MI3W
HBL432P3W
—
—
60
2P 3W
120V
HBL360MI4W
HBL360P4W
—
—
2P 3W
240V
HBL360MI6W
HBL360P6W
—
—
2P 3W
480V
HBL360MI7W
HBL360P7W
—
—
3P 4W
120/240V
HBL460MI12W
HBL460P12W
HBL460MI12WR
HBL460P12WR
3P 4W
3Ø 240V
HBL460MI9W
HBL460P9W
HBL460MI9WR
HBL460P9WR
3P 4W
3Ø 480V
HBL460MI7W
HBL460P7W
HBL460MI7WR
HBL460P7WR
3P 4W
3Ø 600V
HBL460MI5W
HBL460P5W
HBL460MI5WR
HBL460P5WR
4P 5W
3ØY 120/208V
HBL560MI9W
HBL560P9W
—
—
4P 5W
3ØY 277/480V
HBL560MI7W
HBL560P7W
—
—
4P 5W
3ØY 347/600V
HBL560MI5W
HBL560P5W
—
—
2P 3W
240V
HBL3100MI6W
HBL3100P6W
—
—
3P 4W
120/240V
HBL4100MI12W
HBL4100P12W
HBL4100MI12WR
HBL4100P12WR
3P 4W
3Ø 240V
HBL4100MI9W
HBL4100P9W
HBL4100MI9WR
HBL4100P9WR
3P 4W
3Ø 480V
HBL4100MI7W
HBL4100P7W
HBL4100MI7WR
HBL4100P7WR
3P 4W
3Ø 600V
HBL4100MI5W
HBL4100P5W
HBL4100MI5WR
HBL4100P5WR
4P 5W
3ØY 120/208V
HBL5100MI9W
HBL5100P9W
30
100
Configuration
Recep.
Plug
AC Voltage
Mechanical Interlock
Mating Plug
Mechanical Interlock
Mating Plug
—
—
Note: 20, 30 and 32A – 1 inch NPT hub supplied; 60 and 100A – 1¼ inch hub supplied.
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-21
Pin and Sleeve Devices/Mechanical Interlocks
Auxiliary Contacts for 20, 30, 32, 60 and 100A Switch, NEMA A600 Pilot Duty
Description
Catalog Number
“Break After Main Break”, 1 set of n/o contacts, 1 set of n/c contacts.
“Break Before Main Break”, 1 set of n/o contacts.
HBLAC1
HBLAC2
Ground Block
HBLAC1
Description
Catalog Number
For 20, 30 and 32A switches.
For 60 and 100A switches.
HBL30RGB
HBL60100RGB
Neutral Block
HBLAC2
Description
Catalog Number
For 20, 30 and 32A switches.
For 60A switches.
For 100A switches.
HBL30RNB
HBL60RNB
HBL100RNB
Watertight Closure Plug Kits
Description
Catalog Number
For 20, 30 and 32A Circuit-Lock Unfused and Fused Pin and Sleeve mechanical interlocks. MICPK30
For 60 and 100A Circuit-Lock Unfused and Fused Pin and Sleeve mechanical interlocks.
MICPK60
Replacement Flip Covers
HBL30RNB
HBL30RGB
Description
Catalog Number
For 20A mechanical interlocks.
For 30 and 32A, 3 and 4 wire mechanical interlocks.
For 30A, 5 wire mechanical interlocks.
For 60A mechanical interlocks.
For 100A mechanical interlocks.
CA420MI
CA3430MI
CA530MI
CA60MI
CA100MI
Replacement Switches
Description
Catalog Number
For 20A mechanical interlocks.
For 30 and 32A mechanical interlocks.
For 60 and 100A mechanical interlocks.
HBLDS3RS
HBL30MIRS
HBLDS60100RS
Replacement Mounting Feet
MICPK30
Description
Catalog Number
For 20, 30, 32, 60 and 100A mechanical interlocks.
HBLRFT2*
Dimensions
KEY
CA3430MI
HBL30MIRS
A
B
C
D
E
F
G
H
I
J
K
L
M
HUB SIZE
20A and 30A
Inches (mm)
60A
Inches (mm)
100A
Inches (mm)
7.75" (196.9)
6.87" (174.5)
4.75" (120.7)
1.02" (25.9)
1.60" (40.6)
11.00" (279.4)
8.75" (222.3)
8.00" (203.2)
10.12" (257.0)
6.88" (174.8)
1.93" (49.0)
11.25" (285.8)**
7.75" (196.9)
1.00" NPT
7.75" (196.9)
6.87" (174.5)
4.75" (120.7)
1.02" (25.9)
1.46" (37.1)
12.75" (323.9)
8.75" (222.3)
9.75" (247.7)
11.87" (301.5)
6.88" (174.8)
2.09" (53.1)
13.65" (346.7)
8.60" (218.4)
1.25" NPT
7.75" (196.9)
6.87" (174.5)
4.75" (120.7)
1.02" (25.9)
1.46" (37.1)
12.75" (323.9)
8.75" (222.3)
9.75" (247.7)
11.87" (301.5)
6.88" (174.8)
2.09" (53.1)
13.65" (346.7)
9.30" (236.2)
1.25" NPT
Note: *Package of 10 feet and 10 screws.
**30 and 32A, 3 and 4W = 11.50" (292.1);
30A, 5W = 11.59" (294.4).
A
B
C
D
E
J
F
K
H
L
I
HBLRFT2
G
Dimensions in Inches (mm)
G-22
®
Wiring Device-Kellems
M
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Typical Specifications
Manufacturer’s Identification Description
Electrical Type
Rating
Configuration
Enclosure Type
Ingress Protection
Enclosure Material
Certification
Hubbell HBL430MI7W
Circuit-Lock® Pin and Sleeve Mechanical Interlock
3 Pole + Earth
30A, 480V AC, 3 Phase
IEC 60309-2, UL1686 C2, Clock position 7
Outdoor - 4X (Watertight, Washdown); Indoor - 12 (Dust-tight, Falling Dirt and Noncorrosive Liquids)
IP67 Suitability
Non-metallic, enclosure suitable for metallic conduit
UL Listed, CSA Certified
Note: This device provides on/off switched control of a plug connected load and includes an interlocking feature to prevent the plug from being disconnected while the
receptacle is energized. The switch cannot be turned “ON" until the plug is inserted properly, and the plug cannot be removed until the switch is turned “OFF."
Materials
Part
Material
Base
Handle
Enclosure Gasket
Shaft Seal
Enclosure Screws
Hinge Pins
Valox®Top
Conduit Hub
Valox®
Neoprene
Shaft
Neoprene
Ground Plate
Stainless Steel 300 Series
Enclosure Inserts
Nickel Plated Brass
Hinge Spring
Part
Material
Valox®
Zinc
Valox®
Galvanized Steel
Brass
Stainless Steel 300 Series
Performance
Electrical
Dielectric Voltage Max. Working Voltage
Current Interrupting
Short Circuit Withstand Rating
Operations
Withstands 3,000V AC Min.
600V AC RMS.
Certified for current interrupting at full rated current and voltage.
Suitable for use on a circuit capable of delivering not more than 10,000 RMS symmetrical amperes at the voltage rating of
the receptacle. 20A and 30A models: Suitable for use on a circuit capable of delivering not more than 65,000 RMS symmetrical
amperes, 600V when protected by class “J” fuses rated 30A.
Mechanical 10,000 cycles, electrical 6,000 cycles.
Mechanical
Impact Resistance
Terminal Identification
Product Identification
Mounting
In accordance with UL 746C.
In accordance with UL, CSA and international conventions.
Identification and ratings are part of the external label and molded into the receptacle mount.
External adjustable feet.
Environmental
Moisture Resistance
Ingress Protection
Flammability
Operating Temperature
UV Resistance
Outdoor - 4X (Watertight, Washdown); Indoor - 12 (Dust-tight, Falling Dirt and Noncorrosive Liquids).
IP67 Suitability.
UL94-5VA and V-0 Classification.
Max. Continuous +75°C; Min. Continuous -40°C.
All materials are UV stabilized.
Horsepower Ratings
Amps
AC Voltage Rating
Horsepower
Mechanical Interlock
Mating Plug
20
20
20
20
30
30
30
30
30
30
30
30
30
30
32
60
60
60
60
60
60
60
60
60
60
100
100
100
100
100
100
120/240V AC
3Ø 240V AC
3Ø 480V AC
3Ø 600V AC
120V AC
240V AC
480V AC
120/240V AC
3Ø 600V AC
3Ø 480V AC
3Ø 250V AC
3ØY 347/600V AC
3ØY 277/480V AC
3ØY 120/208V AC
380V AC 50Hz – 440V AC 60Hz
120V AC
240V AC
480V AC
120/240V AC
3Ø 600V AC
3Ø 480V AC
3Ø 250V AC
3ØY 347/600V AC
3ØY 277/480V AC
3ØY 120/208V AC
240V AC
120/240V AC
3Ø 600V AC
3Ø 480V AC
3Ø 250V AC
3ØY 120/208V AC
2
5
10
10
2
3 (208-240V AC)
7.5
3 (208-240V AC)
20
15
7.5
20
15
5
15 (440V AC 3Ø 60Hz)
3
7.5 (208-240V AC)
20
7.5 (208-240V AC)
40
30
15
40
30
15
15 (10 @ 208V AC)
15
50
50
25 (208-240V AC)
20
HBL420MI12W
HBL420MI9W
HBL420MI7W
HBL420MI5W
HBL330MI4W
HBL330MI6W
HBL330MI7W
HBL430MI12W
HBL430MI5W
HBL430MI7W
HBL430MI9W
HBL530MI5W
HBL530MI7W
HBL530MI9W
HBL432MI3W
HBL360MI4W
HBL360MI6W
HBL360MI7W
HBL460MI12W
HBL460MI5W
HBL460MI7W
HBL460MI9W
HBL560MI5W
HBL560MI7W
HBL560MI9W
HBL3100MI6W
HBL4100MI12W
HBL4100MI5W
HBL4100MI7W
HBL4100MI9W
HBL5100MI9W
HBL420P12W
HBL420P9W
HBL420P7W
HBL420P5W
HBL330P4W
HBL330P6W
HBL330P7W
HBL430P12W
HBL430P5W
HBL430P7W
HBL430P9W
HBL530P5W
HBL530P7W
HBL530P9W
HBL432P3W
HBL360P4W
HBL360P6W
HBL360P7W
HBL460P12W
HBL460P5W
HBL460P7W
HBL460P9W
HBL560P5W
HBL560P7W
HBL560P9W
HBL3100P6W
HBL4100P12W
HBL4100P5W
HBL4100P7W
HBL4100P9W
HBL5100P9W
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-23
Pin and Sleeve Devices/Mechanical Interlocks
Features and Benefits
IP66
SUITABILITY
Fused Circuit-Lock® Pin and Sleeve Mechanical Interlocks
Hubbell Circuit-Lock® Pin and Sleeve Mechanical
Interlocks are a revolutionary design that incorporates
a disconnect switch and pin and sleeve receptacle in a
compact non-metallic unit. These devices offer maximum
safety by preventing users from mating or breaking
a circuit under load—Hubbell’s interlock mechanism
detects the presence of a plug and prevents it from
being removed when the switch is in the "ON" position.
It features a high visibility red handle that can be locked
to meet OSHA lockout/tagout regulations, and the
enclosure door can be locked to prevent unauthorized
access. The rugged, corrosion-resistant Type 4X Valox®
enclosure features adjustable mounting feet for flexible
installation, while the receptacle’s spring-loaded cover
with gasket is dust tight and provides a watertight seal
when turned and locked.
The patented Plug-Check™ mechanism detects the
presence of the plug. It operates as a clutch to engage
the handle with the switch and captures the plug. This
action prevents the plug from being removed until the
switch is turned OFF.
• Mechanically interlocked to prevent mating and
breaking under load
• Available in both IEC and UL1686-C1 Insulgrip® styles
• IEC reverse service units available for safely
connecting generators
HBL460MIF5W
Housing Design
• Non-metallic enclosure meets UL 50E
Type 4X (watertight), 12 (dust-tight)
and IP66 suitability requirements.
Enclosure is molded of rugged
thermoplastic Valox® to resist abuse,
corrosion and enhance safety
• Stainless steel ¼ turn door fasteners
for quick, easy access to fuses
Interior Design
• Compact Fused Disconnect Switch
accepts Class “J” fuses. Fuse holders
are top mounted for easy access
• The switch accepts auxiliary contacts for
control circuit applications including the
ON/OFF control of remote pilot lights or
signal for programmable controllers
Safety
• High visibility red handle can be locked
in the OFF position as a method
of compliance with OSHA lockout
requirements. Accepts up to a ⁵⁄₁₆ inch
padlock shackle
• Replaceable spring-loaded receptacle
liftcover with gasket ensures dust tight
rating; liftcover provides watertight seal
when turned and locked
Contact Carrier
• Thermoset polyester contact carrier
provides resistance to electrical
tracking and withstands higher
temperatures
• Thermoset properties provide
excellent dimensional stability, low
moisture absorption and superior
dielectric strength
Enclosure Door
• Removable door for ease of wiring
and installation
• Enclosure door can be locked
to prevent unauthorized access.
Additionally, if the switch is ON,
the door cannot be opened
Installation
• Three molded-in conduit drill points are
located on the top, bottom and back
surface of enclosure. Conduit hub
provided: 30A 1 in. NPT, 60A 1¼ in. NPT
• Conduit hub and adjustable mounting
feet (4) are ductile to allow mounting on
irregular surfaces
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
G-24
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
IP66
Enclosure Type 4X, 12
SUITABILITY
Fused Circuit-Lock® Devices
Rating
Amps
Poles
and
Wires
30
60
Configuration
Recep./
Plug/
Conn.
Inlet
AC Voltage
Mechanical Interlock
Mating Plug
3P 4W
120/240V
HBL430MIF12W
HBL430P12W
3P 4W
3Ø 240V
HBL430MIF9W
HBL430P9W
3P 4W
3Ø 480V
HBL430MIF7W
HBL430P7W
3P 4W
3Ø 600V
HBL430MIF5W
HBL430P5W
4P 5W
3ØY 277/480V
HBL530MIF7W
HBL530P7W
4P 5W
3ØY 347/600V
HBL530MIF5W
HBL530P5W
3P 4W
120/240V
HBL460MIF12W
HBL460P12W
3P 4W
3Ø 240V
HBL460MIF9W
HBL460P9W
3P 4W
3Ø 480V
HBL460MIF7W
HBL460P7W
3P 4W
3Ø 600V
HBL460MIF5W
HBL460P5W
4P 5W
3ØY 120/208V
HBL560MIF9W
HBL560P9W
HBL430MIF12W
Gray Style Switch
HBLACFSNO
HBL30MIFRS
Black Style Switch
Note: 30A – 1 inch NPT hub supplied; 60A – 1¼ inch hub supplied.
Replacement Auxiliary Contacts
Description
Black Style Switch
Catalog Number
Gray Style Switch
Catalog Number
Auxiliary contact, normally open, A600 pilot duty, break before break.
ACFSNO
HBLACFSNO
Auxiliary contact, normally closed, A600 pilot duty, break before break.
ACFSNC
HBLACFSNC
ACFSNO
30MIFRS
Note: Auxiliary contacts are specific to the style switch noted and are NOT interchangeble. All new installations are shipped with
gray style switch.
Replacement Switches
Description
Black Style Switch
Catalog Number
Gray Style Switch
Catalog Number
For 30A fused switches.
30MIFRS
HBL30MIFRS
—
HBL60MIFRS
For 60A fused switches. Gray Style switch will retro fit Black Style switch.
Note: If replacing a Black Style switch, you must use the 30MIFRS. All other applications can use the Gray Style switch.
MICPK30
Watertight Closure Plug Kits
Description
Catalog Number
For 30A Circuit-Lock® unfused and fused Pin and Sleeve mechanical interlocks.
MICPK30
For 60 and 100A Circuit-Lock® unfused and fused Pin and Sleeve mechanical interlocks.
MICPK60
Replacement Flip Covers
Description
Catalog Number
For 30A, 3 and 4 wire mechanical interlocks.
CA3430MI
For 30A, 5 wire mechanical interlocks.
CA530MI
For 60A mechanical interlocks.
CA60MI
CA3430MI
Replacement Mounting Feet
Description
Catalog Number
Replacement mounting feet and screws for 30 and 60A fused mechanical interlocks.
HBLRFT2 ∆
HBLRFT2
Note: ∆ Package of 10 feet and 10 screws.
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-25
Pin and Sleeve Devices/Mechanical Interlocks
Specifications
Materials
Typical Specifications
Manufacturer’s Identification
Description
Electrical Type
Rating
Configuration
Enclosure Type
Certification
Hubbell HBL460MIF7W
Fused Circuit-Lock Pin and Sleeve Mechanical Interlock
3 Pole + Earth
60A, 480V AC, 3 Phase
IEC 60309-2, UL1686C2, Clock Position 7
Outdoor - 4X (Watertight, Washdown)
Indoor - 12 (Dust-tight, Falling dirt)
UL Listed for US and Canada
Part
Material
Base and Top
Handle
Conduit Hub
Enclosure Gasket
Shaft
Shaft Seal
Ground Plate
Enclosure Screws
Mounting Inserts
Hinge Pin
Hinge Spring
Valox®
Valox®
Zinc, 30A-1", 60A-1¼" NPT
Neoprene
Brass
Neoprene
Galvanized Steel
Stainless Steel
Brass
Nickel-Plated Brass
Stainless Steel
Note: This device provides fused switched control of a plug connected load and includes an interlocking feature to prevent the plug from being disconnected or the fuse
door opened while the receptacle is energized. The switch cannot be turned on until the plug is inserted properly.
Performance
Electrical
Dielectric Voltage
Max. Working Voltage
Current Interrupting
Short Circuit Withstand Rating
Withstands 3,000V AC Min.
600V AC.
Certified for current interrupting at full rated current and voltage.
Suitable for use on a circuit capable of delivering not more than 200,000 RMS symmetrical amperes
at the voltage rating of receptacle.
Mechanical 10,000 cycles minimum.
Operations
Mechanical
Impact Resistance
Terminal Identification
Product Ratings
Mounting
In accordance with UL 746C.
In accordance with UL, CSA and international conventions.
Ratings are part of the external label and molded into the receptacle mount and color-coded.
External adjustment feet.
Environmental
Moisture Resistance
Ingress Protection
Flammability
Operating Temperatures
UV Resistance
Fuse Types
Outdoor - 4X (Watertight, Washdown); Indoor - 12 (Dust-tight, Falling dirt).
IP66 Suitability.
UL94-5VA and V-0 Classification.
Max. Continuous +75°C; Min. Continuous -40°C.
All materials are UV stabilized.
UL Listed Class “J”. CSA Certified HRCI-J.
Horsepower Ratings
Amps
AC Voltage Rating
Standard
Maximum**
Mechanical Interlock
Use Pin and Sleeve Plug
30
30
30
30
30
30
60
60
60
60
60
3Ø 600V AC
3Ø 480V AC
3Ø 240V
120/240V AC
3ØY 277/480V
3ØY 347/600V
3Ø 600V AC
3Ø 480V AC
3Ø 240V AC
120/240V AC
3ØY 120/208V
7.5
5
3
1.5*
5
7.5
15
15
7.5
3*
7.5
20
15
7.5
3*
15
20
50
30
15
10*
15
HBL430MIF5W
HBL430MIF7W
HBL430MIF9W
HBL430MIF12W
HBL530MIF7W
HBL530MIF5W
HBL460MIF5W
HBL460MIF7W
HBL460MIF9W
HBL460MIF12W
HBL560MIF9W
HBL430P5W
HBL430P7W
HBL430P9W
HBL430P12W
HBL530P7W
HBL530P5W
HBL460P5W
HBL460P7W
HBL460P9W
HBL460P12W
HBL560P9W
Note: *208-240V AC L-L.
**Requires time delay fuses.
Dimensions
7.27" (184.7)
1.51" (38.4) 30A
1.68" (42.7) 60A
10.18" (258.6)
9.31" (236.5)
3.60"
(91.4)
7.19"
(182.6)
11.46"
(291.6)
12.37"
(314.2)
15.03"
(381.8)
14.48"
(367.8)
15.36"
(390.1)
2.69" (68.3) 30A
2.83" (71.9) 60A
8.43" (214.1)
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
Dimensions in Inches (mm)
G-26
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
RoHS
Features and Benefits
20 and 30 Amps Low Profile
Hubbell Wiring Device-Kellems Low Profile Compact Design, these
devices are often used in indoor locations and maintenance, food service
areas where aesthetics and space are concerns, assembly areas,
stamping operations, warehouse and maintenance areas.
Applications: Agriculture, Chemical Processing, Construction,
Entertainment, Food Service, Light Manufacturing, Military.
L430R9
L430P9
Housing Design
• Nylon construction, both interior
and exterior are made of tough,
durable nylon
• Shrouding, recessed pins are
protected from impact and abuse
Cord Grip
• Integrated cord grip limits strain on
terminals, keeps cord connected
Safety
• Large markings for easy recognition
Brass Box Terminal
• Permits high clamping pressure on
conductors without damaging wire
strands for best electrical conductivity
• Solid one-piece pins construction, for
long life, reliable electrical contact and
maximum conductivity
Identification
• Color coding for quick, easy visual
identification of mating devices
• Ratings and certification are molded
into the nylon housing for easy
identification and reordering
Split Sleeves
• Self-adjusting stainless steel springs
assure constant contact pressure (20A
and 30A). On 60A devices, Beryllium
copper insert with multiple contact points
assures easy insertion and a tight fit
• Stainless steel terminal screws resist
rust and corrosion
results in ease of wiring on the
assembly line or in the field
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-27
Pin and Sleeve Devices/Mechanical Interlocks
RoHS
Low Profile Devices
Rating
Devices
Cord Diameter
Configuration
Amps
Poles
and
Wires
20
3P 4W
3Ø 250V
—
L420R9
.350" - .710"
(8.3 - 15.9)
30
3P 4W
125/250V
L430P12
L430R12
.390" - .775"
(9.9 - 19.7)
30
3P 4W
3Ø 250V
L430P9
L430R9
.390" - .775"
(9.9 - 19.7)
Amps
Poles
and
Wires
Plug
Receptacle
60
3P 4W
A460P9
A460R9
Amps
Poles
and
Wires
Plug
Receptacle
60
4P 5W
3ØY 120/208V
A560P9
HBL560R9W
.89" - 1.42"
(22.6 - 36.1)
100
4P 5W
3ØY 120/208V
A5100P9
HBL5100R9W
1.34" - 1.50"
(34.0 - 38.1)
Recep./ Plug/
Conn.
Inlet
AC Voltage
Plug
Configuration
Recep./ Plug/
Conn.
Inlet
AC Voltage
3Ø 250V
AC Voltage
.75" - 1.25"
(19.1 - 31.8)
Dielectric Withstand Voltage
Max. Working Voltage
Current Interrupting
Temperature Rise
Endurance
3000V AC.
250V RMS.
Certified for current interruption at full rated current.
Max. 30 C temperature rise at full rated current
after 50 cycles of overload at 150% of rated
current at a power factor of 75%.
Up to 5,000 connect and disconnect cycles at
full rated current and voltage.
Mechanical
Impact Resistance
Cord Grip Cable Retention
Cord Accommodation
Terminal Identification
Product Identification
Min. Max.
Inches (mm)
Application Guide
Electrical
Per CSA C22.2 No. 182.1 / UL1682.
Per CSA C22.2 No. 182.1 / UL1682.
Round portable service cords of diameters
commensurate with the device rating as defined
in UL standard 62, CSA C22.2 No. 49 and the
<HAR> European Standards.
Terminals identified in accordance with North
American convention.
Ratings are a permanent part of the device housing.
Environmental
HB or better per UL 94 or CSA.
C22.2 No. 0.17.
IP22 Suitability
Maximum Continuous 75° C;
Minimum -40°C without impact.
® Zytel and Rynite are registered trademarks of E.I. DuPont Corp.
G-28
Min. Max.
Inches (mm)
Configuration
Recep./ Plug/
Conn.
Inlet
Specifications
Flammability
Ingress Protection
Operating Temperatures
Min. Max.
Inches (mm)
Receptacle
®
Agriculture
Indoor location and maintenance.
Chemical Processing
Indoor location and maintenance.
Construction
Indoors for added safety and abuse resistance.
Entertainment
Indoor location and maintenance.
Food Service
Food service areas where aesthetics
and space are concerns.
Light Manufacturing
Indoor locations and maintenance.
Manufacturing
Light assembly areas, stamping
operations and maintenance areas.
Military
Warehouse and maintenance areas.
Materials
PlugMaterial
CaseZytel® 101 Nylon
ShroudZytel® 101 Nylon
Pin Carrier 20 & 30A
Zytel® 101 Nylon
Pin and Carrier 60A
High-Impact Thermoset
Pins
Brass CDA#360
Assembly Screws
Stainless Steel (300 series)
Terminal Screws
Stainless Steel (300 series)
Receptacle
BodyZytel® 101 Nylon
Sleeve Carrier 20 & 30A Zytel® 101 Nylon
Sleeve Carrier 60A
High-Impact Thermoset
Sleeves
Brass CDA #360
Assembly Screws
Stainless Steel (300 series)
Terminal Screws
Stainless Steel (300 series)
Adapter Plate 20 & 30A Galvanized Steel
Adapter Plate 60A
Aluminum
Wall Trim Plate
Zytel® 101 Nylon
Panel Mount Trim Plate Stainless Steel (300 series)
Note: See page G-27 for product dimensions.
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Plug Dimensions
Type
A
B
C
D
Cord Range Diameter
L430P12
2.97"
(75.4)
4.18"
(106.2)
3.50"
(88.9)
1.71"
(43.4)
.390"-.775"
(9.9-19.7)
A460P9
3.38"
(85.9)
4.25"
(108.0)
7.00"
(177.8)
–
.75"-1.25"
(19.1- 31.8)
A5100P9
4.92"
(125.00)
5.07"
(128.81)
8.60"
(218.35)
–
1.34"-1.50"
(34.0- 38.1)
Plugs
D
Angled Plugs
C
A
C
C
B
A
A
B
30A
B
60A
100A
Wall Mount Receptacle Dimensions
Type
A
B
C
D
E
F
L420R9
2.60"
(66.0)
2.81"
(71.4)
2.28"
(57.9)
2.38"
(60.5)
–
–
L430R12
3.12"
(79.2)
3.12"
(79.2)
2.77"
(70.4)
2.76"
(70.1)
–
–
A460R9
4.50"
(114.3)
4.50"
(114.3)
4.48"
(113.8)
–
3.62"
(91.9)
.50"
(12.7)
Wall Mount Receptacles
A
A
C
B
D
C
B
F
20 and 30A
E
60A
Adapter Plate (Included with “L” and “A” series receptacles)
4.75" Sq.
(120.7)
4.75" Sq.
(120.7)
4.75" Sq.
(120.7)
Panel Cutout
2.55"
(64.8)
2.13"
(54.1)
2.55"
(64.8)
2.13"
(54.1)
20A
Mounting
2-gang box
30A
Mounting
2-gang box
60A
Mounting
2-gang box
and 4¹¹⁄₁₆" box
20A
2.62"
(66.5) dia.
2.83"
(71.9) dia.
30A
Dimensions in Inches (mm)
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-29
Pin and Sleeve Devices/Mechanical Interlocks
IEC Pin and Sleeve Terminal Identification – Rear View
Terminal Marking Pattern*
Rating
Description
Domestic
Receptacle and Connector
International
Domestic
International
Plug and Inlet
Domestic
White
3 Wire
125V AC
277V AC
3 Wire
White
L+
100-130V
Green
250V AC
480V AC
600V AC
Green
L+
200-250V
380-415V AC
L+
Green
4 Wire
Green
Green
White
White
N
L1
L2
—
Green
Pilot
4 Wire
Pilot
L2
380-415V AC
L2
L3
L1
L1
Green
White
5 Wire
(3ØY)
120/208V AC
277/480V AC
347/600V AC
L2
L1
Green
(3Ø ∆)
250V AC
480V AC
600V AC
220/380V 50Hz
250/440V 60Hz
200/346V to
240/415V
50 and 60Hz
L3
Green
L+
N
125/250V AC
1ØY 120/208V
International
Green
Pilot
L2
N
L3
L1
Green
White
Pilot
L2
L3
L1
N
Green
Note:  *Location of grounding contact position will change as clock positions assigned to specific voltages change.
Pilot contacts supplied on 4 and 5 wire, 63 and 125 Amp international rated devices.
G-30
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Ground Path
To reduce the likelihood of electrical shock, the National Electrical Code requires that non-current carrying metallic
components be grounded. Insulgrip Pin and Sleeve wiring devices offer two styles of grounding.
Style I
HBL430PS1W
HBL430RS1W
Receptacles achieve grounding by
attaching the ground conductor
to the ground screw inside
the back box and utilizing the
metallic receptacle shell as a
ground source (see 3P 4W Style I
illustration). Plugs and connectors
establish grounding by means
of connecting the flexible cable
ground conductor to a ground
terminal within each device, which,
in turn, is grounded through the
metallic plug or connector shroud.
Any exposed metallic components
are suitably grounded in the Style I
offering.
Style II
HBL430PS2W
HBL430RS2W
The Style II ground path offers two
means of achieving the proper
ground path. In addition to utilizing
the same grounding method as
in the Style I product, the Style II
version incorporates a separate
ground pin and sleeve (see 3P 4W
Style II illustration). This provides a
second ground path. The ground
pin on Style II devices is longer
than other pins, meaning that
they “make first" and “break last,"
assuring protection for people and
equipment.
New Pole and Wire Terminology
Style I
Style II
New
Old
No. of Contacts
New
Old
No. of Contacts
2P 3W
3P 4W
4P 5W
2W 2P
3W 3P
4W 4P
2
3
4
2P 3W
3P 4W
2W 3P
3W 4P
3
4
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-31
Pin and Sleeve Devices/Mechanical Interlocks
TYPE 4X
Features and Benefits
UL 1686 C1 Insulgrip® Pin and Sleeve Devices
With the introduction of UL standard 1686-C1, configurations are uniform
throughout the industry. That means Hubbell–the name that sets the standard for
pin and sleeve performance, reliability, durability, innovation and ease of use–can
finally become your standard. Hubbell's new line of heavy duty Insulgrip® Pin and
Sleeve wiring devices not only offers complete interchangeability, it delivers the
goods when it comes to superior design and construction. Hubbell Insulgrip Pin
and Sleeve devices are engineered and built to handle today’s most demanding
work environments, making Hubbell the unsurpassed heavyweight in the heavy
duty market.
G-32
Housing Design
• Thermoplastic housing provides
excellent insulating, impact, corrosion,
and UV resistant properties. Protects
users and internal components in the
roughest of environments
• Spring-loaded, gasketed cover provides
a UL Type 4X watertight, dust-tight seal
on connectors and receptacles
Liquidtight Conduit Adapters
• Machined aluminum adapters are
available to provide a means for
attaching flexible liquidtight metal
conduit to rear of Hubbell Pin and
Sleeve plug or connector
Powerful Mechanical Cord Grip
• Hubbell’s design incorporates two
molded-in teeth to securely grip
the outer cable jacket, and internal
conductors to prevent slippage and
strain on terminations
• Captive barrel nuts ease assembly
and allow higher tightening torque
for maximum cord retention
Terminal Entrance Holes
• Large, square funneled entrance holes
isolate each conductor to protect against
shorts due to stray conductor strands
• Tapered hole provides a fast and easy
guide into the termination chamber
• Pin chamber confines arcing within the
interior chamber during make and break
cycle of mating devices, minimizes arc
tracking
Watertight Cord Entrance
• The tapered bore entrance creates
high compression forces on sealing
gland, providing a watertight seal
around cord
• Individual solid neoprene glands
are supplied to match a full range
of cord sizes and assure watertight
performance
Anti-Vibration Box Terminals
• Interlocking box terminals ensure that
terminal screws remain secure and
cannot loosen
• The floating box is designed to obtain
high-torque values without damaging
stranded conductors
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
TYPE 4X
Features and Benefits
UL 1686 C1 Insulgrip® Pin and Sleeve Devices
Metallic where you want It, non-metallic where you need it. Different from traditional
all-metallic devices, Hubbell Pin and Sleeve wiring devices are designed to provide
metallic shrouding where you want it and a non-metallic housing where you need it.
What’s more, Hubbell’s new watertight Insulgrip Pin and Sleeve wiring devices
are designed with safety first and foremost. We created the line with plant facility
maintenance personnel and a safer industrial work environment in mind. To greatly
reduce the likelihood of electrical shock, we developed our exclusive nonmetallic
watertight system, meaning that with Hubbell on the job, the mix of electricity and
water isn’t the threat it once was. So, whether the job calls for a
welding outlet in a dry location or a motor disconnect
in a wet location, step up to Hubbell Pin and Sleeve
wiring devices.
Housing Design
• Thermoplastic housing provides
excellent insulating, impact, corrosion,
and UV resistant properties. Protects
users and internal components in the
roughest of environments
• Locking ring provides a UL Type 4X
watertight and dust-tight seal when
the male and female devices are
connected
Shrouded Sleeves
• Housing seal provides a watertight
and dust-tight seal when mated with
receptacle or connector
• Protects the user from the possibility of
touching live contacts during insertion
and withdrawal of mating parts
• Shrouded sleeves protects contact
sleeves from deforming from physical
abuse
Interior Design
• Sleeve O-ring seal provides a watertight
and dust-tight seal around the sleeves.
Assures that contamination will not
enter wire chamber
• All-brass sleeve contacts provide
Thermoset Polyester Contact Carrier
• Molded thermoset polyester provides
high resistance to electrical tracking
• Withstands higher temperatures which
may result from overload or arcing
• Thermoset properties provide dimensional
stability for this critical assembly
Product Marking
• Catalog number and rating visible
while in use. Markings are color
coded differentiating Style I and
Style II devices
Beryllium Copper Spring-Pin
Design (Patented)
• Maintains high unit pressure on mating
sleeves. Ensures reliable electrical
contact while minimizing heat rise due
to normal pin wear over time
reliable electrical contact with mating
pins, also with minimum heat build-up
over time
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-33
Pin and Sleeve Devices/Mechanical Interlocks
TYPE 4X**
Rating
Amps
30
2P 3W
600/250
HBL330RS1W
HBL330PS1W
HBL330CS1W
IN330FS1
IN330MS1
3P 4W
600/250
HBL430RS1W
HBL430PS1W
HBL430CS1W
IN430FS1
IN430MS1
4P 5W
600/250
HBL530RS1W
HBL530PS1W
HBL530CS1W
IN530FS1
IN530MS1
2P 3W
600/250
HBL360RS1W
HBL360PS1W
HBL360CS1W
IN360FS1
IN360MS1
3P 4W
600/250
HBL460RS1W
HBL460PS1W
HBL460CS1W
IN460FS1
IN460MS1
4P 5W
600/250
HBL560RS1W
HBL560PS1W
HBL560CS1W
IN560FS1
IN560MS1
2P 3W
600/250
HBL3100RS1W
HBL3100PS1W
HBL3100CS1W
IN3100FS1
IN3100MS1
3P 4W
600/250
HBL4100RS1W
HBL4100PS1W
HBL4100CS1W
IN4100FS1
IN4100MS1
4P 5W
600/250
HBL5100RS1W
HBL5100PS1W
HBL5100CS1W
IN5100FS1
IN5100MS1
3P 4W
600/250
HBL4200RS1W
HBL4200PS1W
HBL4200CS1W
IN4200FS1†
IN4200MS1†
4P 5W
600/250
HBL5200RS1W
HBL5200PS1W
HBL5200CS1W
IN5200FS1†
IN5200MS1†
100
200
Maximum
Voltage
AC/DC
Replacement Interiors
Poles
and
Wires
60
Receptacle/
Connector
Configuration*
Style I Devices
Plug
Receptacle
Rating
Style II Devices
Plug
Replacement Interiors
Amps
30
2P 3W
600/250
HBL330RS2W
HBL330PS2W
HBL330CS2W
IN330FS2
IN330MS2
3P 4W
600/250
HBL430RS2W
HBL430PS2W
HBL430CS2W
IN430FS2
IN430MS2
2P 3W
600/250
HBL360RS2W
HBL360PS2W
HBL360CS2W
IN360FS2
IN360MS2
3P 4W
600/250
HBL460RS2W
HBL460PS2W
HBL460CS2W
IN460FS2
IN460MS2
2P 3W
600/250
HBL3100RS2W
HBL3100PS2W
HBL3100CS2W
IN3100FS2
IN3100MS2
3P 4W
600/250
HBL4100RS2W
HBL4100PS2W
HBL4100CS2W
IN4100FS2
IN4100MS2
2P 3W
600/250
HBL3200RS2W
HBL3200PS2W
HBL3200CS2W
IN3200FS2†
IN3200MS2 †
3P 4W
600/250
HBL4200RS2W
HBL4200PS2W
HBL4200CS2W
IN4200FS2†
IN4200MS2 †
100
200
Maximum
Voltage
AC/DC
Connector &
Receptacle
Poles
and
Wires
60
Receptacle/
Connector
Configuration*
Connector
Receptacle
Rating
Amps
Poles
and
Wires
200
4P 5W
Receptacle/
Connector
Configuration*
Plug
Connector
Corrosion Resistant Devices
Maximum
Voltage
AC/DC
Receptacle
M5200RS1
600/250
Plug
M5200PS1
Connector &
Receptacle
Plug
Accessories
Connector
M5200CS1
Back Boxes
MB2003W
MB2004W
Angle Adapter
AA20045
Note: *CAUTION: To avoid electrical shock, review premises carefully and DO NOT use if Pin and Sleeve configuration (design) is already in a circuit having a rating differing
from the rating of this device.
**While in use or with cover closed.
†Consult factory.
Corrosion resistant cord sets are available on page Y-17 of this catalog.
G-34
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
TYPE 4X**
Rating
Amps
Poles
and
Wires
30
2P 3W
600/250
3P 4W
60
100
200
Receptacle/
Connector
Configuration*
“Reversed Service” Style I Devices
Maximum
Voltage
AC/DC
Receptacle
Connector
HBL330RS1WR
HBL330PS1WR
HBL330CS1WR
IN330MS1
IN330FS1
600/250
HBL430RS1WR
HBL430PS1WR
HBL430CS1WR
IN430MS1
IN430FS1
4P 5W
600/250
HBL530RS1WR
HBL530PS1WR
HBL530CS1WR
IN530MS1
IN530FS1
2P 3W
600/250
HBL360RS1WR
HBL360PS1WR
HBL360CS1WR
IN360MS1
IN360FS1
3P 4W
600/250
HBL460RS1WR
HBL460PS1WR
HBL460CS1WR
IN460MS1
IN460FS1
4P 5W
600/250
HBL560RS1WR
HBL560PS1WR
HBL560CS1WR
IN560MS1
IN560FS1
2P 3W
600/250
HBL3100RS1WR
HBL3100PS1WR
HBL3100CS1WR
IN3100MS1
IN3100FS1
3P 4W
600/250
HBL4100RS1WR
HBL4100PS1WR
HBL4100CS1WR
IN4100MS1
IN4100FS1
4P 5W
600/250
HBL5100RS1WR
HBL5100PS1WR
HBL5100CS1WR
IN5100MS1
IN5100FS1
3P 4W
600/250
HBL4200RS1WR
HBL4200PS1WR
HBL4200CS1WR
IN4200MS1†
IN4200FS1†
4P 5W
600/250
HBL5200RS1WR
HBL5200PS1WR
HBL5200CS1WR
IN5200MS1†
IN5200FS1†
Rating
30
2P 3W
600/250
3P 4W
200
Receptacle/
Connector
Configuration*
“Reversed Service” Style II Devices
Amps
100
Connector &
Receptacle
Plug
Poles
and
Wires
60
Replacement Interiors
Maximum
Voltage
AC/DC
Replacement Interiors
Connector &
Receptacle
Plug
Connector
HBL330RS2WR
HBL330PS2WR
HBL330CS2WR
IN330MS2
IN330FS2
600/250
HBL430RS2WR
HBL430PS2WR
HBL430CS2WR
IN430MS2
IN430FS2
2P 3W
600/250
HBL360RS2WR
HBL360PS2WR
HBL360CS2WR
IN360MS2
IN360FS2
3P 4W
600/250
HBL460RS2WR
HBL460PS2WR
HBL460CS2WR
IN460MS2
IN460FS2
2P 3W
600/250
HBL3100RS2WR
HBL3100PS2WR
HBL3100CS2WR
IN3100MS2
IN3100FS2
3P 4W
600/250
HBL4100RS2WR
HBL4100PS2WR
HBL4100CS2WR
IN4100MS2
IN4100FS2
2P 3W
600/250
HBL3200RS2WR
HBL3200PS2WR
HBL3200CS2WR
IN3200MS2†
IN3200FS2 †
3P 4W
600/250
HBL4200RS2WR
HBL4200PS2WR
HBL4200CS2WR
IN4200MS2†
IN4200FS2 †
Rating
Amps
Poles
and
Wires
200
4P 5W
Receptacle/
Connector
Configuration*
Receptacle
Plug
“Reversed Service” Corrosion Resistant Devices
Maximum
Voltage
AC/DC
600/250
Receptacle
M5200BS1R
Plug
Connector
M5200CS1R
—
Plug
Accessories
Back Boxes
MB2003W
MB2004W
Angle Adapter
AA20045
Note: *CAUTION: To avoid electrical shock, review premises carefully and DO NOT use if Pin and Sleeve configuration (design) is already in a circuit having a rating differing
from the rating of this device.
**While in use or with cover closed.
†Consult factory.
Corrosion resistant cord sets are available on page Y-17 of this catalog.
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-35
Pin and Sleeve Devices/Mechanical Interlocks
Insulgrip Pin and Sleeve Metallic Back Boxes
Hubbell manufactures an extensive line of back boxes for use with UL 1686 Pin and Sleeve
devices. Each back box is designed to give the user the maximum amount of wiring room
while achieving grounding to metallic conduit.
Metallic 30º Angle Back Box*
MB301W
Description
Amps
NPT Hub Size
Catalog Number
Back box for 30A devices.
30
30
¾"
1"
MB301W
MB302W
Metallic 15º Angle Back Box*
MB304W
Description
Amps
NPT Hub Size
Catalog Number
Back box for 60A devices.
60
60
60
1"
1¼"
1½"
MB601W
MB602W
MB603W
Metallic Feed-Thru Back Box*
Description
Amps
NPT Hub Size
Catalog Number
Straight feed-thru box for
30A devices.
Straight feed-thru box for
60A devices.
30
30
60
60
60
¾"
1"
1"
1¼"
1½"
MB303W
MB304W
MB604W
MB605W
MB606W
Metallic Four-Way Angle Back Box*
MB601003W
Description
Amps
NPT Hub Size
Catalog Number
Four-way 15° angle box for
60 and 100A devices.
60/100
60/100
60/100
200
200
200
1¼"
1½"
2"
2"
2½"
-
MB601002W
MB601003W
MB601004W
MB2003W
MB2004W
AA20045
Four-way 45° angle box for
200A devices.
45° Angle adapter only for
200A devices.
MB601006W
Metallic Four-Way Feed-Thru 15º Angle Back Box*
Description
Amps
NPT Hub Size
Catalog Number
Four-way feed-thru, 15° angle
for 60 and 100A devices.
60/100
60/100
60/100
1¼"
1½"
2"
MB601006W
MB601007W
MB601008W
Note: *These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
Replacement Cord Clamp and Locking Ring
MB2003W
Description
Used on
Cord Clamp
Catalog Number
Locking Ring
Catalog Number
Fits all 30A plugs and connectors.
Fits all 60A plugs and connectors.
All 3, 4, 5 wire
4 wire (Style 2) and all 5 wire
All 3 wire and 4 wire (Style 1)
4 wire (Style 2) and all 5 wire
All 3 wire and 4 wire (Style 1)
All 3, 4, 5 wire
CC3430
CC60
CC60
CC100
CC100
CC201
ILR1**
ILR2**
ILR3**
ILR4**
ILR5**
—
Rating of Hubbell
Pin and Sleeve Device
Liquidtight
Conduit Size
Hubbell
Liquidtight Adapter
Optional Kellems
Liquidtight Conduit Grip
30 Amp
½" NPT
¾" NPT
1" NPT
1" NPT
1¼" NPT
1¼" NPT
1½" NPT
SAB12
SAB34
SAB100
SAC100
SAC125
SAD125
SAD150
074093402
074093403
074093404
074093404
074093405
074093405
074093406
Fits all 100A plugs and connectors.
CC3430
Fits all 200A plugs and connectors.
Note: **Locking Ring only.
ILR1
SAB34
Liquidtight Adapters
60 Amp
100 Amp
074093403
G-36
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Plug Dimensions
Connector Body Dimensions
A
Amps
30
B
Style II
Style I
330P 7.53" (191)
7.53" (191)
3.00" (76) 3.00" (76) .375-1.20" (9.5-30.5)
430P 7.53" (191)
7.53" (191)
530P 7.53" (191)
60
A
Type Style I
Style II
Cord Grip Range
Amps
Style II
Style I
330C 8.38" (213)
8.38" (213)
3.74" (95) 3.74" (95) .375-1.20" (9.5-30.5)
3.00" (76) 3.00" (76) .375-1.20" (9.5-30.5)
430C 8.38" (213)
8.38" (213)
3.74" (95) 3.74" (95) .375-1.20" (9.5-30.5)
3.00" (76)
530C 8.38" (213)
360C 9.90" (251)
9.90" (251)
3.50" (89) 3.50" (89) .500-1.45" (12.7-36.8)
460C 9.90" (251)
10.10" (256) 3.50" (89) 3.80" (96) .500-1.45" (12.7-36.8)
30
.375-1.20" (9.5-30.5)
360P 9.40" (239)
9.40" (239)
3.40" (86) 3.40" (86) .500-1.45" (12.7-36.8)
460P 9.40" (239)
9.40" (239)
3.40" (86) 3.70" (94) .500-1.45" (12.7-36.8)
560P 9.40" (239)
B
Type Style I
3.70" (94)
60
.500-1.45" (12.7-36.8)
100 3100P 10.70" (272) 10.70" (272) 3.70" (94) 3.70" (94) .925-1.94" (27.0-49.3)
Style II
3.74" (95)
560C 10.10" (256)
Cord Grip Range
.375-1.20" (9.5-30.5)
3.80" (96)
.500-1.45" (12.7-36.8)
100 3100C 11.70" (297) 11.70" (297) 4.50" (114)4.50" (114).925-1.94" (27.0-49.3)
4100P 10.70" (272) 10.90" (277) 3.70" (94) 4.00" (102) .925-1.94" (27.0-49.3)
4100C 11.70" (297) 11.90" (302) 4.50" (114)4.70" (119) .925-1.94" (27.0-49.3)
5100P 10.90" (277)
5100C 11.90" (302)
200 3200P
4.00" (102)
11.13" (282)
.925-1.94" (27.0-49.3)
6.35" (161) 1.00-2.50" (25.4-63.5)
200 3200C
4.70" (119)
13.65" (346)
.925-1.94" (27.0-49.3)
7.00 (177) 1.00-2.50" (25.4-63.5)
4200P 11.13" (282) 11.13" (282) 6.35" (161) 6.70" (170) 1.00-2.50" (25.4-63.5)
4200C 13.65" (346) 13.65" (346) 7.00" (177)7.39 (187) 1.00-2.50" (25.4-63.5)
5200P 11.13" (282)
5200C 13.65" (346)
6.70" (170)
1.00-2.50" (25.4-63.5)
7.39" (187)
A
1.00-2.50" (25.4-63.5)
A
B
B
Receptacle Dimensions
A
B
C
D
E
Amps
Type
Style I
Style II
Style I
Style II
Style I
Style II
Style I
Style II
Style I
Style II
30
330R
2.72" (69)
2.72" (69)
3.40" (86)
3.40" (86)
3.89" (99)
3.89" (99)
3.19" (81)
3.19" (81)
1.37" (35)
1.37" (35)
430R
2.72" (69)
2.72" (69)
3.40" (86)
3.40" (86)
3.89" (99)
3.89" (99)
3.19" (81)
3.19" (81)
1.37" (35)
1.37" (35)
60
100
530R
2.72" (69)
360R
3.50" (89)
3.50" (89)
4.25" (108)
3.40" (86)
4.25" (108)
4.66" (118)
4.66" (118)
4.42" (112)
4.42" (112)
1.54" (39)
1.54" (39)
460R
3.50" (89)
3.50" (89)
4.25" (108)
4.25" (108)
4.66" (118)
4.66" (118)
4.42" (112)
4.42" (112)
1.54" (39)
1.54" (39)
560R
3.50" (89)
4.25" (108)
3.19" (81)
4.66" (118)
1.37" (35)
4.42" (112)
1.54" (39)
3100R 3.50" (89)
3.50" (89)
4.25" (108)
4.25" (108)
4.66" (118)
4.70" (119)
5.30" (135)
5.30" (135)
1.54" (39)
1.54" (39)
4100R 3.50" (89)
3.50" (89)
4.25" (108)
4.25" (108)
4.66" (118)
4.70" (119)
5.30" (135)
5.30" (135)
1.54" (39)
1.54" (39)
5100R 3.50" (89)
200
3.89" (99)
4.25" (108)
3200R
6.50" (165)
4200R 6.50" (165)
6.90" (170)
5200R 6.90" (170)
7.00" (177)
7.00" (177)
7.39" (187)
D
A
4.66" (118)
7.39" (187)
5.30" (135)
5.63" (143)
5.63" (143)
5.63" (143)
5.63" (143)
7.76" (197)
7.76" (197)
7.76" (197)
7.76" (197)
A
E
1.54" (39)
D
.99" (25)
.99" (25)
.99" (25)
.99" (25)
E
C
C
B
B
30, 60 and 100 Amp
200 Amp
Dimensions in Inches (mm)
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-37
Pin and Sleeve Devices/Mechanical Interlocks
Metallic Angle Back Box
NPT
Hub
Size
A
Inch
(mm)
B
Inch
(mm)
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
F
Inch
(mm)
30° Angle back
box for 30A
devices.
¾"
4.87"
(124.0)
2.94"
(75.0)
4.02"
(102.0)
3.40"
(86.0)
4.25"
(108.0)
2.12"
(54.0)
MB301W
1"
4.87"
(124.0)
2.94"
(75.0)
4.02"
(102.0)
3.40"
(86.0)
4.25"
(108.0)
2.12"
(54.0)
MB302W
15° Angle back
box for 60A
devices.
1"
–
4.80"
(121.9)
–
–
5.25"
(133.4)
2.69"
(68.3)
MB601W
1¼"
–
4.80"
(121.9)
–
–
5.25"
(133.4)
2.69"
(68.3)
MB602W
1½"
–
4.80"
(121.9)
–
–
5.25"
(133.4)
2.69"
(68.3)
MB603W
Description
E
A
C
F
B
D
Metallic Angle Box
Catalog Number
Metallic Feed-Thru Back Box
E
Description
Back box for
30A devices.
A
C
B
D
Back box for
60A devices.
NPT
Hub
Size
A
Inch
(mm)
B
Inch
(mm)
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
F
Inch
(mm)
¾"
5.35"
(136.0)
2.91"
(74.0)
4.53"
(115.0)
3.59"
(91.0)
2.62"
(67.0)
–
MB303W
1"
5.35"
(136.0)
2.91"
(74.0)
4.53"
(115.0)
3.59"
(91.0)
2.62"
(67.0)
–
MB304W
1"
6.50"
(165.1)
3.80"
(97.0)
5.75"
(146.1)
4.50"
(114.3)
3.50"
(88.9)
–
MB604W
1¼"
6.50"
(165.1)
3.80"
(97.0)
5.75"
(146.1)
4.50"
(114.3)
3.50"
(88.9)
–
MB605W
1½"
6.50"
(165.1)
3.80"
(97.0)
5.75"
(146.1)
4.50"
(114.3)
3.50"
(88.9)
–
MB606W
Metallic Feed-Thru Box
Catalog Number
Metallic Four-Way Angle Back Box
E
15° Angle fourway box for
60 and 100A
devices.
C
A
B
Description
D
Metallic Four-Way Angle Box
45° Angle fourway box for
200A devices.
45° Angle adapter
only for 200A devices.
E
Four-way
Feed-thru box
for 60 and 100A
devices.
C
15°
B
A
Inch
(mm)
B
Inch
(mm)
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
F
Inch
(mm)
Catalog Number
1¼"
7.92"
(201.0)
8.52"
(216.0)
7.00"
(178.0)
6.14"
(156.0)
4.88"
(124.0)
–
MB601002W
1½"
7.92"
(201.0)
8.52"
(216.0)
7.00"
(178.0)
6.14"
(156.0)
4.88"
(124.0)
–
MB601003W
2"
7.92"
(201.0)
8.52"
(216.0)
7.00"
(178.0)
6.14"
(156.0)
4.88"
(124.0)
–
MB601004W
2"
10.82"
(274.8)
9.86"
(250.4)
9.50"
(241.3)
8.17"
(207.5)
6.75"
(171.5)
–
MB2003W
2½"
10.82"
(274.8)
9.86"
(250.4)
9.50"
(241.3)
8.17"
(207.5)
6.75"
(171.5)
–
MB2004W
–
8.00"
(203.2)
6.00"
(152.4)
7.00"
(178.0)
8.00"
(203.2)
7.00"
(178.0)
–
AA20045
Metallic Four-Way Feed-Thru 15º Angle Back Box
Description
A
NPT
Hub
Size
D
Metallic Feed-Thru Angle Box
NPT
Hub
Size
A
Inch
(mm)
B
Inch
(mm)
C
Inch
(mm)
D
Inch
(mm)
E
Inch
(mm)
F
Inch
(mm)
Catalog Number
1¼"
7.98"
(202.7)
8.55"
(217.2)
7.00"
(178.0)
6.14"
(156.0)
4.88"
(124.0)
–
MB601006W
1½"
7.98"
(202.7)
8.55"
(217.2)
7.00"
(178.0)
6.14"
(156.0)
4.88"
(124.0)
–
MB601007W
2"
7.98"
(202.7)
8.55"
(217.2)
7.00"
(178.0)
6.14"
(156.0)
4.88"
(124.0)
–
MB601008W
Note: These boxes are cast aluminum, suitable for IP54 requirements and are finished with enamel paint.
Dimensions in Inches (mm)
G-38
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Materials (30, 60, 100, and 200 Amp)
Typical Specification
PlugMaterial
Manufacturer’s ID
Description Electrical Type Max. Rating Configuration Certification HousingValox® 357 (200A Aluminum)
Plug Shroud
Aluminum
Cord Clamps
Rynite® SST35 (200A Aluminum)
Clamp Nut
Nickel Plated Brass
Gland Cap
Rynite® SST35
GlandNeoprene
O-Rings, Gaskets & Seals
Neoprene
Contact Carrier
Thermoset Polyester
Retainer
Thermoset Polyester
Sleeves
Brass (M-Series - Nickel-plated
tellurium copper)
Box Terminal
Heat Treated & Zinc Plated Steel
Screws (Terminal, Assembly & Set) Stainless Steel (300 Series)
Ground Standoff
Brass
Ground Bracket
Nickel Plated Spring Bronze
Locking Ring
Epoxy Painted Aluminum
Connector Body
Hubbell HBL430PS2W
Plug, Power Supply
3 Pole + Earth
30 Amp, 600V AC, 250V DC, 50-400Hz
UL 1686, Watertight, C1 Configuration
UL Listed, UL Standard 1682, UL 50, and
UL 1010 (plugs only), CSA Certified to CSA Spec. C22.2 No. 182.1, No. 94 and No. 159 (plugs only), UL Listed and CSA Certified Type 4X
Performance
Electrical
Dielectric Voltage
Withstands 3,000V AC.
Max. Working Voltage 600V AC RMS (i.e., minimum creepage and
clearance distance of 6.4 millimeters, per UL 1682).
Current Interrupting
Certified for current interrupting at full rated
current.
Temperature Rise
Max. 30°C temperature rise at full rated current after 50 cycles of overload at 150% of rated current.
Endurance
Up to 1,000 connect and disconnect cycles at
full rated current and voltage.
HousingValox® 357 (200 Amp Aluminum)
Connector Shroud
Epoxy Painted Aluminum
Cord Clamps
Rynite® SST35
Clamp Nut
Nickel Plated Brass
Gland Cap
Rynite® SST35 (200A Aluminum)
GlandNeoprene
O-Rings, Gaskets & Seals
Neoprene
Contact Carrier
Thermoset Polyester
Retainer
Thermoset Polyester
Pin
Brass (M-Series - Nickel-plated
tellurium copper)
Pin Spring
Beryllium Copper
Box Terminal
Heat Treated & Zinc Plated Steel
Screws (Terminal, Assembly & Set) Stainless Steel (300 Series)
Ground Standoff
Brass
Ground Bracket
Nickel Plated Spring Bronze
Cover
Epoxy Painted Aluminum
Cover Arm
Epoxy Painted Aluminum
Spring Guide
Stainless Steel (300 Series)
Springs (Arm & Wave)
Stainless Steel (300 Series)
Spring Washer
Stainless Steel (300 Series)
Hinge Bushing
Aluminum
RivetAluminum
Hose Down & Moisture Type 3, 4, 4X per UL 50E and CSA 22.2, No. 94.
Resistance
Flammability (Enclosure) UL 94V-0 and CSA C22.2 No. 0.17.
Operating Temperatures Maximum Continuous 75°C; Minimum
-40°C without impact -25° with impact.
Hazardous Location
Class I, Division I & II, Groups B, C & D and
(30, 60 & 100A)
Class II, Division I & II, Groups F & G per
(plug only)
UL 1010 & CSA 22.2, No. 159.
Receptacle
Materials
Housing/Flange
Epoxy Painted Aluminum
O-Rings, Gaskets & Seals
Neoprene
Contact Carrier
Thermoset Polyester
Retainer
Thermoset Polyester
Pin
Brass (M-Series - Nickel-plated
tellurium copper)
Pin Spring
Beryllium Copper
Box Terminal
Heat Treated & Zinc Plated Steel
Screws (Terminal, Assembly & Set) Stainless Steel (300 Series)
Ground Standoff
Brass
Ground Bracket
Steel
Cover
Epoxy Painted Aluminum
Cover Arm
Epoxy Painted Aluminum
Spring Guide
Stainless Steel (300 Series)
Springs (Arm & Wave)
Stainless Steel (300 Series)
Spring Washer
Stainless Steel (300 Series)
Hinge Bushing
Aluminum
RivetAluminum
Mechanical
Impact Resistance
Cord Grip Cable
Retention
Cord Accommodation
Terminal Identification
Product Identification
Per CSA C22.2, No. 182.1, UL 1682.
Per CSA C22.2, No. 182.1, UL 1682.
Round portable service cords of diameters
commensurate with the device rating as defined
in UL. Standard 62, CSA C22.2 No. 49 and the
harmonized <HAR> European Standards.
Terminals identified in accordance with UL 1686
(1, 2, 3, Green).
Identification and ratings are permanently fastened to the device housing.
Environmental
HousingsValox® 357 (200A Aluminum).
All Other Materials
Resistant to corrosion and chemical attack.
Watertight Application Guide
IndustryWatertight.
Agriculture
Chemical Processing
Construction
Entertainment
Food Processing
Food Service
Light Manufacturing
Manufacturing
Military
Outdoor for fans, heaters, pumps, etc.
Where subject to water, corrosion.
Outdoors subject to severe weather conditions.
Outdoors subject to severe weather.
Where subject to water, corrosion.
Areas subject to wash downs & heavy cleaning.
Subjected to cleaning, solvents & chemicals.
Where subject to water, corrosion.
Outdoor construction or maintenance.
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
Rynite® is a registered trademark of E.I. DuPont Corp.
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-39
Pin and Sleeve Devices/Mechanical Interlocks
Features and Benefits
Style II Insulgrip® Mechanical Interlocks
Hubbell Circuit-Lock® Pin and Sleeve Mechanical
Interlocks are a revolutionary design that incorporates
a disconnect switch and pin and sleeve receptacle in a
compact non-metallic unit. These devices offer maximum
safety by preventing users from mating or breaking
a circuit under load—Hubbell’s interlock mechanism
detects the presence of a plug and prevents it from
being removed when the switch is in the "ON" position.
It features a high visibility red handle that can be locked
to meet OSHA lockout/tagout regulations, and the
enclosure door can be locked to prevent unauthorized
access. The rugged, corrosion-resistant Type 4X Valox®
enclosure features adjustable mounting feet for flexible
installation, while the receptacle’s spring-loaded cover
with gasket is dust tight and provides a watertight seal
when turned and locked.
The patented Plug-Check™ mechanism detects the
presence of the plug. It operates as a clutch to engage
the handle with the switch and captures the plug. This
action prevents the plug from being removed until the
switch is turned OFF.
• Mechanically interlocked to prevent mating and
breaking under load
• Available in both IEC and UL1686-C1 Insulgrip® styles
• IEC reverse service units available for safely
connecting generators
HBL430MIFS2W
Housing Design
• Non-metallic enclosure meets UL 50E
Type 4X (watertight), 12 (dust-tight)
and IP66 suitability requirements.
Enclosure is molded of rugged
thermoplastic Valox® to resist abuse,
corrosion and enhance safety. All
external hardware is stainless steel
• Stainless steel ¼ turn door fasteners
for quick, easy access to fuses
Interior Design
• Compact Fused Disconnect Switch
accepts Class “J” fuses. Fuse holders
are top mounted for easy access
• The switch accepts auxiliary contacts for
control circuit applications including the
ON/OFF control of remote pilot lights or
signal for programmable controllers
Safety
• High visibility red handle can be locked
in the OFF position as a method
of compliance with OSHA lockout
requirements. Accepts up to a ⁵⁄₁₆ inch
padlock shackle
• Replaceable spring-loaded receptacle
liftcover with gasket ensures dust tight
rating; liftcover provides watertight seal
when turned and locked
Contact Carrier
• Thermoset polyester contact carrier
provides resistance to electrical
tracking and withstands higher
temperatures
• Thermoset properties provide
excellent dimensional stability, low
moisture absorption and superior
dielectric strength
Enclosure Door
• Removable door for ease of wiring
and installation
• Enclosure door can be locked
to prevent unauthorized access.
Additionally, if the switch is ON,
the door cannot be opened
Installation
• Three molded-in conduit drill points are
located on the top, bottom and back
surface of enclosure. Conduit hub
provided: 30A 1 in. NPT, 60A 1¼ in. NPT
• Conduit hub and adjustable mounting
feet (4) are ductile to allow mounting on
irregular surfaces
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
G-40
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
TYPE 4X**
Style II - Fused
Fused Insulgrip® Mechanical Interlocks
Rating
Amps
Poles
and
Wires
30
3P 4W
600/250
HBL430MIFS2W
HBL430PS2W
60
3P 4W
600/250
HBL460MIFS2W
HBL460PS2W
Receptacle/
Connector
Configuration*
Maximum
Voltage
AC/DC
Mechanical Interlock
Mating Plug
HBL430MIFS2W
Style II - Unfused
Gray Style Switch
Unfused Insulgrip® Mechanical Interlocks
Rating
HBLACFSNO
Amps
Poles
and
Wires
30
3P 4W
600/250
HBL430MIS2W
HBL430PS2W
60
3P 4W
600/250
HBL460MIS2W
HBL460PS2W
Receptacle/
Connector
Configuration*
Maximum
Voltage
AC/DC
Mechanical Interlock
Mating Plug
HBL30MIFRS
Black Style Switch
Note: 30A – 1 inch NPT hub supplied; 60A – 1¼ inch hub supplied.
*CAUTION: To avoid electrical shock, review premises carefully and DO NOT use if Pin and Sleeve configuration (design)
is already in a circuit having a rating differing from the rating of this device.
**While in use or with cover closed.
Replacement Auxiliary Contacts
Description
Black Style Switch Gray Style Switch
Auxiliary contact, normally open, A600 pilot duty, break before break.
Auxiliary contact, normally closed, A600 pilot duty, break before break.
ACFSNO
ACFSNC
HBLACFSNO
HBLACFSNC
ACFSNO
30MIFRS
Note: Auxiliary contacts are specific to the style switch noted and are NOT interchangeble. All new installations are shipped
with gray style switch.
Replacement Switches
Description
Black Style Switch Gray Style Switch
For 30A fused switches.
30MIFRS
For 60A fused switches. Gray Style switch will retro fit Black Style switch.
—
For 30A unfused switches.
30MISRS
For 60A unfused switches. Gray Style switch will retro fit Black Style switch.
—
HBL30MIFRS
HBL60MIFRS
HBL30MISRS
HBL60MISRS
Note: If replacing a Black Style switch, you must use the 30MIFRS. All other applications can use the Gray Style switch.
MICPK30
Watertight Closure Plug Kits
Description
Catalog Number
For 30A Circuit-Lock® unfused and fused Pin and Sleeve mechanical interlocks.
For 60 and 100A
Circuit-Lock®
MICPK30
MICPK60
unfused and fused Pin and Sleeve mechanical interlocks.
Replacement Mounting Feet
Description
Catalog Number
Replacement mounting feet and screws for 30 and 60A fused mechanical interlocks.
HBLRFT2 ∆
Note:
∆ Package
of 10 feet and 10 screws.
eSpec Sheets Available Online
®
HBLRFT2
Wiring Device-Kellems
G-41
Pin and Sleeve Devices/Mechanical Interlocks
Typical Specifications
Manufacturer’s Identification
Description
Electrical Type
Rating
Configuration
Enclosure Type (UL 50E)
Ingress Protection
Certification
Performance
Hubbell HBL460MIFS2W
Fused Insulgrip® Pin and Sleeve
Mechanical Interlock
3 Pole + Earth
60A, 250VDC/600VAC
Per UL 1686 C1
Outdoor - 4X (Watertight, Washdown)
Indoor - 12 (Dust Tight, Falling Dirt)
IP66 Suitability
UL Listed for US and Canada
Note: This device provides fused switched control of a plug connected load and
includes an interlocking feature to prevent the plug from being disconnected
or the door from opening­while the receptacle is energized. The switch
cannot be turned on until the plug is fully inserted.
Materials
Electrical
Dielectric Voltage Max. Working Voltage
Current Interrupting
Short Circuit
Withstand Rating
Operations
Mechanical
Impact Resistance
Terminal Identification
Product Ratings
Mounting
Part
Material
Environmental
Base, Door and Handle
Conduit Hub
Enclosure Gasket and Shaft Seal
Shaft and Mounting Inserts
Ground Plate
Enclosure Screws and Hinge Spring
Hinge Pin
Contact Carrier
Valox®
Zinc, 30A – 1 in., 60A – 1¼ in. NPT
Neoprene
Moisture Resistance
Ingress Protection
Flammability
Operating Temperatures
UV Resistance
Fuse Types
Brass
Galvanized Steel
Stainless Steel
Nickel-Plated Brass
Thermoset Polyester
Withstands 3,000VAC Min.
250VDC/600VAC.
Certified for current interrupting at full rated
current and voltage.
Suitable for use on a circuit capable of delivering not more than 200,000 RMS symmetrical amperes at the voltage rating
of receptacle.
Mechanical 10,000 cycles minimum.
In accordance with UL 746C.
In accordance with UL, CSA and international conventions.
Ratings are part of the external label and
molded into the receptacle housing.
External adjustable feet.
Outdoor - 4X (Watertight, Washdown); Indoor - 12 (Dust-tight, Falling dirt).
IP66 Suitability.
UL94-5VA and V-0 Classification.
Max. Continuous +60°C;
Min. Continuous -40°C w/o impact.
All exposed insulating materials are
UV stabilized.
UL Listed Class “J”.
CSA Certified HRCI-J.
Horsepower Ratings
30A Horsepower Ratings
60A Horsepower Ratings
3 Phase A.C.
3 Phase A.C.
Standard
Maximum*
200-240V 3
7.5
480V 5 15
600V 7.520
Standard
Maximum*
200-240V7.5
15
480V1530
600V 15 50
Note: *Requires time delay fuses.
Dimensions
7.27"
(184.7)
10.18"
(258.6)
9.31"
(236.5)
7.19"
(182.6)
1.51" (38.4) 30A
1.68" (42.7) 60A
3.60"
(91.4)
11.46"
(291.6)
12.37"
(314.2)
15.03"
(381.8)
14.48"
(367.8)
15.36"
(390.1)
4.00" (101.6) 30A
5.00" (127.0) 60A
8.43"
(214.1)
Note: 30A – 1 inch NPT hub supplied; 60A – 1¼ inch hub supplied.
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
Dimensions in Inches (mm)
G-42
®
Wiring Device-Kellems
www.hubbell-wiring.com
Pin and Sleeve Devices/Mechanical Interlocks
Features and Benefits
Hazardous Location Non-Fused Mechanical Interlocks and Plugs
Hubbell’s Hazardous Location Line of Non-Fused UL 1686 Mechanical Interlock
Disconnect Switches are typically used for applications with the presence of
flammable gasses or vapors, ignitable dusts and fibers. They are also suitable for
use in outdoor or indoor damp, wet and dirty locations or in areas where frequent
wash downs, heavy rain, or water spray routinely occurs.
These switches are compact in size to reduce cost and make it easier to position
on the wall or piece of equipment. The enclosures are made of copper-free
aluminum and have a polyester/epoxy finish to prevent corrosion. The high visibility
handles can be locked out to comply with OSHA lock out/tag out regulations.
VSQ Hazardous Location Ratings
Class I, Div. 1 & 2, Groups B,C,D
Class I, Zones I & 2, Groups IIB+H2, IIA
Class II, Div. 1 & 2, Groups F & G
Class lll
NEMA 3, 4, 4X, 7 (B,C,D), 9 (F,G)
HBLVP3485
HBLVSQ3034
Housing Design
• Copper-free aluminum construction
with electrostatically applied polyester/
epoxy finish to prevent corrosion
• Compact NEMA 4X enclosure and
footfrint allows easy installation in
tight locations
Internal Design
• Internal switch horsepower rated as
“suitable as a motor disconnect”
• Auxiliary contact (late-make earlybreak) contact rated 10 Amp, 1/3
HP at 125/250V AC can be used for
operating pilot lights or starter coils
•Feed-through construction
Safety
• Lockable handle to meet OSHA
Lockout/Tagout regulations
• Large visible rotary handle with ON/
OFF indicator allows a quick means
of disconnecting power
• Handle mechanism is chemical
resistant Valox® (TM Sabic)
thermoplastic
Plug Locking Ring
• NEMA 4X with receptacle lid turned
shut or with plug locking ring tightened
Mechanism
• Plug and switch are interlocked. Switch
cannot be turned ON without fully
inserted plug Plug cannot be removed
with switch in ON position
• Plug held in place when switch is OFF
for convenience. Pull operated release
mechanism
Fully Interchangeable
• Product is UL1686 and is fully
interchangeable with other UL1686
configured and listed devices
Valox® is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.
eSpec Sheets Available Online
®
Wiring Device-Kellems
G-43
Pin and Sleeve Devices/Mechanical Interlocks
30 and 60 Amp Non-Fused UL1686 Mechanical Interlocks and Plugs
Amp
Circuit
Mechanical Interlock
Plug
30 Amp
600V AC
2W 3P
HBLVSQ3023
HBLVP3385
3W 4P
HBLVSQ3034
HBLVP3485
60 AMP
600V AC
2W 3P
HBLVSQ6023
HBLVP6385
3W 4P
HBLVSQ6034
HBLVP6485
Note: HBLVSQ 30 Amp models come standard with 1 inch drilled and tapped conduit openings top and bottom plus two 1 inch x
¾ inch reducers and one ¾ inch close-up plug for maximum flexibility. 60 amp models come with one 1½ inch opening on
top and bottom and one 1½ inch close-up plug.
HBLVSQ3034
Horsepower Ratings (VAC)*
Amp
30 Amp
60 Amp
HBLVP3485
Circuit
120
240
480
1Ø
2
5
10
600
15
3Ø
3
7.5
15
20
1Ø
–
10
15
20
3Ø
–
10
25
30
Note: *Internal switch only.
Dimensions
A
B
C
D
E
F
30A
Mechanical Interlocks
5.75 (146)
10.50 (267)
9.75 (248)
3.75 (95)
3.13 (79)
8.13 (206)
60A
8.13 (206)
14.16 (360)
11.28 (287)
4.03 (102)
2.50 (64)
11.38 (289)
D
E
A
C
E
D
B F
Plugs
A
B
C
30A Both
6.69 (170)
3.00 (76)
1.88 (48)
5.38 (137)
2.53 (64)
60A, 3 Pole
8.81 (224)
3.38 (86)
2.25 (57)
6.50 (165)
3.00 (76)
60A, 4 Pole
8.81 (224)
3.69 (94)
2.53 (64)
6.50 (165)
3.00 (76)
A
B
E
C
Wire Range
Reg. Stranded
Extra Flex
Grip Range
D
30A
#10 – #6
#10 – #8
.55–1.2 (14–30)
60A
#6 – #4
#6 – #4
.65–1.5 (16–38)
Dimensions in Inches (mm)
G-44
®
Wiring Device-Kellems
www.hubbell-wiring.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement