Pentax R-200 R-202NE, R-205NE Total Station Instruction manual

PDF

Document

Advertentie

total station

r-200

serIes

InstructIon manual

Basic Procedures

for r-200 serIes r-202ne r-205ne (Power)

TI Asahi Co., Ltd.

International sales Department

4-3-4 ueno Iwatsuki-Ku, saitama-shi saitama, 339-0073 Japan tel.: +81-48-793-0118 fax. +81-48-793-0128 e-mail: [email protected]

www.pentaxsurveying.com/en/

GENERAL

Contents

Exemption clause

Warning

Usage Precautions

1. BASIC OPERATION

Names

1.2

1.3 Standard equipment

1.4 Removing and attaching the Battery

DISPLAY KEYBOARD

keyboard

Function 16

POINT, 18

3.1 Centring and Levelling of the Instrument 19

3.2 19

3.3 Optical plummet （Option） 20

Levelling

3.5 plate 21

Target

3.8 Attachment and detachment of tribrach 23

POWER 24

the on

Adjusting

4.3

Adjusting 25 an 26

5.2 Resetting the horizontal angle to 0

5.3 horizontal

5.4 Inputting an arbitrary horizontal 27 vertical

5.6 Changing the horizontal angle from clockwise to counter clockwise 28

6.3 32

CORRECTION

7.1 the 33

Changing

7.4 value 36 setting

8.4 Entering the mode for initial

8.6 Example of changing an initial

(selection

8.7 setting

8.8 setting

8.9 Initial setting 4

Accessing

Instrument

CHECKS 45

Circular 45 reticle 46

10.4 Perpendicularity of line of sight to horizontal axis 47

10.6 point 48 plummet

10.7 Optical plummet 49

10.9 axis

10.10 The EDM beam axis

11. Specifications

12. Data collector

Atmospheric

13.3

13.4 Error when no atmospheric correction is made 57

Distance 59

14. Notice to the user of this product 60

Before using this product, be sure that you have thoroughly read and understood this instruction manual to ensure proper operation. After reading this manual, be sure to keep in a convenient place for easy reference.

Exemption clause

1) TI Asahi Co.,Ltd. (TIA) shall not be liable for damage caused by Acts of God, fire, alteration or servicing by unauthorized parties, accident, negligence, misuse, abnormal operating conditions.

TIA shall not be liable for changes or disappearance of data, loss of company profit or interruption of company operation incurred by the use of this product or malfunction of it.

TIA shall not be liable for damage caused by usage not explained in the instruction manual.

TIA shall not be liable for damage to this product caused by other equipment connected to this product.

TI Asahi Co.,Ltd.

TI Asahi Co.,Ltd. is a sole proprietor of the PowerTopoLite software.

The PowerTopoLite software and publication or parts thereof, may not be reproduced in any form, by any method, for any purpose.

TI Asahi Co.,Ltd. makes no warranty, expressed or implied, including but not limited to any implied warranties or merchantability or fitness for a particular purpose, regarding these materials and makes such materials available.

PRECAUTIONS REGARDING SAFETY xx

Safety precautions (Must be followed)

The following items are intended to prevent possible injury to the user or other people and/or damage to the instrument before it occurs. These safety precautions are important to the safe operation of this product and should be observed at all times.

Distinctive displays

The following displays are used to distinguish precautions by the degree of injury or damage that may result if the precaution is ignored.

WARNING

Items indicated by this sign are precautions which, if ignored, would result in serious injury.

CAUTION

Items indicated by this sign are precautions which if ignored may result in injury or material damage.

• Here “injury” refers to injuries such as cuts, burns or electric shock, of which treatment will not likely require hospitalization or long-term attention.

• “Material damage” refers to damage to facilities, buildings, acquired data, etc.

Before using this product, be sure that you have thoroughly read and understood this instruction manual to ensure proper operation. After reading this manual, be sure to keep it in a convenient place for easy reference.

This instrument complies with the protection requirement for residential and commercial areas. If this instrument is used close to industrial areas or transmitters, the equipment can be influenced by electromagnetic fields.

WARNING

Do not stare into the laser beam directly as this may result in damage to your eyes.

R-200 is a Class IIIa (3R) Laser product. Do not look into the laser radiation aperture directly as this may result in damage to your eyes.

Never use the telescope to view intense light such as direct sunlight or sunlight reflected through a prism as this may result in loss of sight.

Do not disassemble, modify or repair this product as there is a risk of laser radiation.

Do not aim the laser beam at a person as it is harmful to the eyes and body. Receive the examination treatment by the doctor when the eyesight or body trouble is doubted by any chance.

• Electro-Magnetic Compatibility (EMC):

This instrument complies with the protection requirement for residential and commercial

areas. If this instrument is used close to industrial areas or transmitters, the equipment can be influenced by electromagnetic fields.

• Do not use this product in a coal mine, in a location where there is coal dust, or near flammable material as there is a risk of explosion.

• Do not disassemble, modify or repair this product as there is a risk of fire, electric shock and burn injury. If you think the product requires repair, contact the retail outlet where you purchased it or an authorized repair site.

• Do not charge BP02 Battery with any battery charger other than BC03 as it entails a risk of fire or burn injury from the battery bursting into flames due to possible differences in voltage or polarity.

• Do not use a damaged electric cord plug or loose electric outlet when charging as there is a risk of fire or electric shock.

• Do not charge the battery while covered by clothes or similar items as there is a risk of fire if the clothes ignite.

• Do not use the battery or charger when wet as there is a risk of fire and burn injury due to short-circuit.

• To prevent making short-circuit when removing the battery and charger from the case and storing them, apply electrically resistant tape to the poles of the battery. Storing the battery and charger as it is may result in fire or burn injury due to short-circuit.

• Do not throw the battery into fire or expose it to heat as there is a risk of injury if it explodes.

CAUTION

For your safety, perform the initial and periodical inspection as well as when the instrument is fixed and adjusted.

When the laser beam enters eyes, an unexpected accident might be caused by blink of eyes.

Do not place the laser product at a height where its laser beam may hit the eyes of car drivers and pedestrians.

Do not place the laser product at a place where its laser beam may hit a reflecting object such as a mirror or a glass window. The reflection beam of the laser is also harmful to the human body.

When not performing measurement, cut off the power supply or shade the objective lens with objective cap to prevent the instrument emitting the laser beam.

Keep the laser product in a place where persons, who do not have the product knowledge, such as children, can not touch it by mistake.

• Before disposing of the instrument, destroy its power supply mechanism to prevent it from emitting the laser beam.

• Do not remove the handgrip without good reason. If it does come off, be sure to attach it securely to the instrument with screws. If it is not fastened securely, the instrument may fall when you use the handgrip, leading to possible injury.

• Do not short the poles of the battery or charger as there is a risk of injury or fire.

• Do not touch any fluid which may leak from the battery as there is a risk of chemical burn injury or reaction.

• Do not insert or remove the electric plug with wet hands as there is a risk of electric shock.

• Do not use the case to stand on as it is slippery and unstable and may cause you to fall, resulting in possible injury.

• Make sure the tripod itself and the instrument on the tripod are both installed securely as insecure installation may cause the tripod to fall over or the instrument to drop, resulting in possible injury.

• Do not carry the tripod with the metal shoe pointing toward another person as it may injure him/her.

• The instrument contains a rechargeable battery and a battery charger.

• It may be illegal to dispose the battery at the end of its useful life.

• Check with your local solid waste officials for details for recycling.

USAGE PRECAUTIONS

Surveying instruments are high-precision instruments. In order to assure that the Electronic

Total Station R-200 series product which you have purchased will provide long-lasting maximum performance, the precautions in this manual must be followed. Make sure to follow these instructions and use this product properly at all times.

[Solar observation]

WARNING

Never view the sun directly using the telescope as this may result in loss of sight.

Never point the objective lens directly at the sun as this may damage internal components.

When using the instrument for solar observation, be sure to attach the specially designed solar filter (MU64) to the objective lens.

[Laser beam]

Do not stare into the laser beam. R-200 is a Class IIIa (3R) Laser product.

[EDM axis]

The R-200 series EDM is a red visible laser beam and the beam diameter is very small.

The beam is emitted from the objective centre. The EDM axis is designed to coincide with the telescope sight axis (but both axes may deviate slightly because of intense temperature changes and a long time lapse).

[Target constant]

Confirm the Target Constant of the instrument before measurement.

If a different constant is to be used, use the correct constant of the target. The constant is stored in the instrument's memory when turned off.

[Reflectorless and reflector sheet]

• Reflectorless (Non-Prism)

The measurement range and accuracy of the Reflectorless mode are based on the condition that laser beam is emitted perpendicular to the white side of a Kodak Gray Card.

The measurement range may be influenced by the shape of the target and its environment.

There is a possibility that the range may vary when the target does not satisfy the conditions above at survey work.

• There is a possibility that correct distance measurement may not be performed by dispersion or reduction of laser beam when the laser beam comes into the target from a diagonal angle.

• There is a possibility that the instrument may not be able to correctly calculate out the distance when receiving reflected laser beam from forth and back directions in case of measuring the target on the road.

• There is a possibility that synthesized values are calculated and the distance may become longer or shorter than the actual one when the operator measures the target of slope or sphere or rugged shape.

• There is a possibility that the instrument may not be able to correctly calculate out the distance by collecting the reflected laser beam from a man or a car that comes and goes in front of the target.

• There is a possibility that the distance may not be correctly measured when measuring a target in the direction where there is a reflecting object (mirror, stainless board, white wall, etc.) or under too strong sunlight.

• In a situation where high accuracy may not be expected, perform the measurement by

Reflector sheet or Prism.

• When using reflector sheet, set the reflector sheet to have its surface to be approx. vertical to the aiming line. If it is positioned not to be approx. right angle, there is a possibility that correct distance measurements may be impossible by dispersion or reduction of laser beam.

In the following environments, the distance may not be possible to be measured; there is a reflecting thing (mirror, stainless board, white wall, etc.) in the direction of the target, and under too strong sunlight

[Battery & charger]

• Do not use any battery or battery charger that is not approved by Pentax as it entails a risk of damaging the instrument.

• If water should happen to splash on the instrument or the battery, wipe it off immediately and allow it to dry in a dry location. Do not put the instrument in the case until it is completely dry as this may result in damage to the instrument.

• Turn off the power when removing the battery from the instrument as removing the battery while the power is still on may result in damage to the instrument.

• The battery mark displayed on the instrument is only an estimation of remaining battery power and is not completely accurate. Replace the battery quickly when it is about to run out of power as the time a battery lasts on one full charge differs depending on conditions of ambient temperature, and the measurement mode of the instrument.

• Confirm the battery level remaining before operating.

[Storage and operating environment]

• To prevent making short-circuit when removing the battery and charger from the case and storing them, apply electric resistant tape to the poles of the battery. Storing the battery and charger as it may result in fire or burn injury due to short-circuit.

• Avoid storing the instrument in places subject to extreme high, low or radically fluctuating temperature. (Ambient temperature range during use: –20° C to +50° C)

• Distance measurements may take longer when atmospheric conditions are poor such as when heat shimmer occurs. When storing the instrument, always put it in its case and avoid storage in dusty location or location subject to vibration or extreme heat or humidity.

• Whenever there is a sharp temperature difference between the instrument’s storage and usage environment, allow the instrument to adjust to the environment for an hour or more before using it. Make sure to protect the instrument from the sun if the location is subject to intense direct sunlight.

• The battery should be charged approximately once per month if the instrument is to be stored for an extended period of time. The instrument should also be removed from its case occasionally and aired out.

• In addition to these precautions, be sure to handle the instrument properly at all times following the descriptions given in the various sections of this manual to assure safe and proper measurements.

[Transporting and carrying the instrument]

• Be careful to protect this instrument from shock of impact and excessive vibration which may result in damage during transportation and shipment.

• When transporting the instrument, always put it in the case and wrap shock absorbing material around it and be sure it is handled as “FRAGILE”.

[Checks and repairs]

• Always check the instrument before beginning work and check that the instrument is maintaining the proper level of precision. Pentax bears absolutely no responsibility for damages due to survey results obtained from surveys conducted without an initial instrument check.

• Never disassemble the instrument, battery or charger, even if you do detect an abnormality, as there is a risk of fire or electric shock due to short-circuit. If you think the product requires repair, contact the retail outlet where you purchased it or an authorized repair site.

1. BASIC OPERATION

1.1 Names of parts

Collimator

Focus ring

Laser indicator

Eyepiece

Plate vial

Instrument height mark

Battery latch

Battery pack

Telescope tangent screw

Telescope clamp screw

Display panel

Key board

Plate vial

Leveling screw

Clamp screw

Tangent screw

Detaching knob

Base plate

Top handle

Objective lens

1.2 Unpacking and packing

[Unpacking the Instrument from the case]

① Set the case down gently with the lid facing upwards.

② Open the latches while pressing down on the lock (safety mechanism) and open the lid of the case.

③ Remove the instrument from the case.

[Packing the instrument in the case]

①

Make sure the telescope is fairly levelled and lightly tighten the telescope clamp screw.

②

Line up the housing marks (round yellow marks on the instrument) and tighten the upper and lower clamp screws.

③ With the housing marks are facing upwards, set the instrument gently in the case without forcing it. Close the lid to the case and secure the latches.

1.3 Standard equipment

• Instrument

• Carrying case

• BP02 battery

• BP03/AC01 charger

• Plumb bob

• Hexagonal wrench

• Rain cover

• CD-ROM (Basic operation & Special Functions manual)

1.4 Removing and attaching the Battery

[Removing the Battery]

① Rotate the knob above the battery pack counter clockwise.

②

Lift up the battery pack and remove it from the instrument.

·

Be absoulutely sure to turn the power off when removing the battery as removing the

battery while the power is still on may result in damage to the instrument.

[Attaching the Battery]

①

Place the channel on the bottom of the battery pack.

② Onto the protrusion of the instrument and push the battery pack down into place.

③ Turn the knob clockwise.

Remaining Battery Charge

When the instrument’s power is turned on, a battery mark “ ”will be displayed on the right of the display screen. This mark can be used to check the charge status of the battery.

Low battery: Please change. Replace with the spare battery or charge.

[Charging the battery]

• The battery BP02 is not charged at our factory shipment. It must be changed before use.

• For BP02 charge, use the special BC03 charger.

AC adaptor Charger

Power supply cord

[Connection of code]

①

Insert the output plug of the power supply code in the jack of the AC adaptor.

②

Insert the output plug of the AC adaptor in the jack of the charger.

③ Insert the power supply plug of the power supply code in the outlet of AC power supply.

[Installation of battery]

①

Draw the battery to the lock lever side and put it on the battery pocket. The battery is firmly installed on the battery pocket.

②

Press down the battery and then slide it to the opposite direction of the lock lever.

③ The lock lever goes up, and the battery is fixed.

④

Under such a condition, if “Connection of the code” is done, the charge with the battery is begun.

Lock lever

Battery

Battery pocket

Charger

[Detaching the battery]

① Press the lock lever and slide the battery to the lock lever direction.

②

Detach the battery packing from the battery pocket.

[Display panel]

① Power supply lamp

④ Installation lamp

② Charge lamp

③ Discharge lamp

⑤ Discharge button

① Power supply lamp (red) : Turns on when the power supply is turned on.

②

Charge lamp (green) : Turns on while charging and turns off when the charge is completed.

③

Discharge lamp (yellow) : Turns on when you push the discharge button.

Turns off when the discharge is completed.

④

Installation lamp (red) : Blinks or turns on when the battery packing is attached normally.

Blinks when charge or discharge and turns on when charge is completed.

(The charge lamp in the lower does not blink and does not turns on)

⑤

Discharge button : Discharge lamp lights when you push this button, and the discharge of battery begins.

[How to charge]

①

It begins charging automatically when you set the battery packing in the charger which beams the power supply lamp.

②

Leave just as it is until the charge is completed.

③ When the charge is completed, the charge lamp is turned off.

④

Detach the battery packing from the charger when the charge is completed.

[Refreshing the battery]

The use time shortens gradually by the phenomenon of “Effect of the memory” when the

NiMH battery leaves capacity and repeats the charge. The voltage recovers after refreshing and the use time returns to normal in such a battery. Please refresh one degree every five times of the charge.

[Refreshing]

Set the battery in the charger as well as the case of the charge. Push the electrical discharge button. The electrical discharge lamp lights and the electrical discharge begins.

The electrical discharge lamp is turned off when the electrical discharge ends, the charge lamp lights, and the charge starts automatically. Leave just as it is until the charge is completed.

When the charge is completed, the charge lamp is turned off. Detach the battery from the charger.

[Time of refreshing and charge]

Battery BP02 is discharged from the state of a full charge at about 540 minutes and the charge is completed from the electrical discharge at about 130 minutes. However, the electrical discharge time is proportional to the remainder capacity of the battery. Moreover, the time required for refreshing might be different from the above-mentioned time according to a surrounding temperature and the state of the battery.

2. DISPLAY AND KEYBOARD

2.1 Display and keyboard

Power supply key Function key Illumination key ESC key

Alphanumeric and +/- key

Enter key

Laser key

2.2 Operation keys

Key Description

[POWER]

ON/OFF of power supply.

[ESC]

[ILLU]

Returns to previous screen or cancels an operation.

Turns the illumination of the LCD display and telescope reticle on and off.

[ENT]

Accepts the selected (highlighted) choice or the displayed screen value.

[LASER]

[Alphanumeric]

Displays the laser plummet and the LD point screen when you push the Laser key.

(Refer to “2.5 LD POINT”).

At the numerical value screen, the numerical value and the sign “.” displayed are input. The English characters printed right under numeric of each key are input.

[HELP]

Pressing [ILLU]+[ESC] key causes a help menu to appear in

MODE A or MODE B or causes a help message to appear.

2.3 Function keys

Display F. Key Description

[MEAS] F1 Pressing this key one time measures the distance in normal mode. Another measurement type can be selected by

InitialSetting 2.

Pressing this key twice measures the distance in coarse mode.

Another measurement type can be selected by initial setting 2.

[TARGET] F2

[0 SET] F3

Switches the target.

REFLECTORLESS / SHEET / PRISM

Resets the horizontal angle to 0° 0’ 0” by pressing twice.

[DISP] F4 Switches the display composition in the order

“H.angle/H.dst./V.dst.”, “H.angle/V.angle/S.dst.” and

“H.angle/V.angle/H.dst./S.dst./V.dst.”.

[MODE] F5

Switches the screen between MODE A and MODE B.

MODE B

[S.FUNC] F1

PowerTopoLite Special Functions.

[ANG SET] F2

Brings up the angle setting screen for setting angle-related parameters.

(H.ANGLE /%GRADE, H.ANGLE INPUT and L/R

REVERSE)

[HOLD] F3 Pressing this key twice retains (holds) the horizontal angle shown on the display.

[CORR] F4 Brings up the screen for changing the target constant, temperature, pressure setting.

[MODE] F5

Switches the screen between MODE A and MODE B.

[Other functions]

[ ] F1

[ ]

[ △ ]

[ ▽ ]

[RETICLE] F3

Moves the cursor to the left.

Moves the cursor to the right.

Moves the cursor up.

Moves the cursor down.

Goes back five items on the screen.

Gose forward five items on the screen.

Changing the reticle illumination when pressing illumination key.

[LCD] F4 Changing the LCD contrast when pressing illumination key.

[ILLU] F5 Changing the LCD illumination when pressing illumination key.

[CLEAR] F5

Clear the figure.

[SELECT] F5

Open the selection window.

[How to move the menu number]

Example:

The cursor is located at Menu 1.

Press the numeric key 0 and 2 to move to Menu 2 or press [F4] [ ▽ ].

2.4 Alphanumeric input

The point name is input by the alphanumeric keys as following.

Key Letter under key Letter & figure order to input

[0]

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[.]

[+/-]

PQRS

TUV

WXYZ

GHI

JKL

MNO

ABC

DEF

[@][.][_][-][:][/][0]

[P][Q][R][S][p][q][r][s][1]

[T][U][V][t][u][v][2]

[W][X][Y][Z][w][x][y][z][3]

[G][H][I][g][h][i][4]

[J][K][L][j][k][l][5]

[M][N][O][m][n][o][6]

[ ][?][!][_][¯][^][|][&][7]

[A][B][C][a][b][c][8]

[D][E][F][d][e][f][9]

[.][,][:][;][#][(][)]

[+][-][*][/][%][=][<][>]

2.5 LD POINT, Laser pointer

The Laser pointer function turns the laser beam on continuously to become the aiming point so that visual confirmation is possible.

①

When the [F2] [ RED MARK] key is pressed after pressing the [Laser] key, the Laser pointer function is turned on. The Laser indicator is turned on and the “ ” mark on the left of the screen blinks while the Laser pointer function is operating.

② If the [Laser] key is pressed and the [F2] [RED MARK] key is pressed while the Laser pointer function is operating, the Laser pointer function is turned off.

• The beam of the sun is strong and visual confirmation is difficult in daytime when outdoors.

• The laser beam is designed not to be able to observe through the telescope.

• Please visually align the laser beam to the target and mark the centre.

Confirm the alignment (horizontal and vertical ) before measuring when performing accurate work like stake out when using the Laser pointer function.

Also refer to “10.9 The EDM beam axis”.

• Please do not look at the laser source of beam directly.

3. PREPARATION FOR SURVEYING

3.1 Centring and Levelling of the Instrument

[Setting up the instrument and the tripod]

①

Adjust the tripod legs so that a height suitable for observation is obtained when the instrument is set on the tripod.

②

Hang the plumb bob on the hook of the tripod, and coarse centre over the station on the ground. At this time, set the tripod and fix the metal shoes firmly into the ground so that the tripod head is as levelled as possible.

③ If the tripod head is mis-levelled by the action of fixing the metal shoes into the ground, correct the level by extending or retracting each leg of the tripod.

Tripod head

Center screw

Instrument

Base plate

Contract

Metal shoe

3.2 Laser plummet

[Laser plummet model]

The instrument is equipped with the laser plummet.The laser plummet is not set to be ON at factory shipping. The laser plummet operation of power supply ON can be set by command

No.520, LD PLUM. For using Command number, refer to “9.2 Accessing by 007”.

[For the Detaching type laser plummet equipment model]

Turn on the laser plummet function by pushing the [Laser] key and [F4] [PLUM.ADJ] key.

Match the position with the leveling screw so that the laser mark coincides with the ground mark.

[For the Shift type laser plummet equipment model]

• Turn on the laser plummet function by pushing the [Laser] key and [F4] [PLUM.ADJ] key.

• Match the position by the tripod so that the laser mark coincides with the ground mark.

• The centring knob is loosened, and the upper plate is pushed by the tip of a finger, and a centre mark is matched to the ground mark.

• Tighten the centring knob.

• Loosen the horizontal clamp screw, rotate the instrument by 90°, and confirm the vial of the circular vial is at the centre position.

Correct the vial with the leveling screw when the vial comes off from the centre position.

[Brightness adjustment of laser]

Sometimes the state of the surface of the ground mark or a surrounding environmental does not allow observing the laser spot easily. Please adjust the brightness of the laser if necessary.

If [Laser] + [F4] [PLUM.ADJ] are pressed in due course., the brightness adjustment screen of the laser plummet device, is displayed.

The Laser plummet becomes darker or brighter by pressing [F1] [ ] / [F2] [ ] key.

The adjustment is completed with the [ENT] key and it returns to RED MARK & LD PLUM. Settings screen.

• The brightness adjustment step of the laser is 10 steps.

• The laser plummet spot can become difficult to see in bright sunlight which makes it difficult to perform the occasional check. In this case, use your foot or the carrying case to make a shadow over the laser position.

• The laser plummet is adjusted to be within ±0.5mm at the instrument height of 1.5m at factory shipping.

• Please double check the amount of the gap

(direction of X and Y direction) by laser plummet with the amount of the gap by plumb bomb etc.

When working accurately you should put out a perpendicular direction using the laser plummet function.

• Please do not look at the laser source of beam directly.

3.3 Optical plummet (Option)

[Detachable type]

①

Look through the optical plummet eyepiece, and rotate the eyepiece knob until the center mark can be seen clearly.

②

Rotate the focusing knob of the optical plummet and adjust the focus to the station on the ground.

③ Rotate the levelling screws and aligh the center mark to the ground mark.

[Shift type]

① Look through the optical plummet eyepiece, and rotate the eyepiece knob until the center mark can be seen clearly.

② Rotate the focusing knob of the optical plummet and adjust the focus on the ground mark.

③

Loosen the centering clamp screw and push the upper plate by finger and stay the center mark on the ground mark.

④

Tighten the centering clamp screw.

⑤

Loosen the horizontal clamp screw and rotate the instrument every 90° and confirm the

Circular vial is centered correctly. If the bubble is not centered, it can be properly set using the leveling screws.

3.4 Levelling with circular vial

Tripod is adjusted according to the following points by extending or contracting the legs so that the bubble of the Circular vial goes to the centre of the circle.

• Shorten the leg at the side of the bubble or extend the leg opposite of the bubble to position the bubble in the centre of the vial circle.

• All three legs are extended or contracted until the bubble is in the centre.

During this process, the foot is not placed on the tripod leg point and the position of the tripod points do not change.

3.5 Levelling with the plate vial

[Leveling]

① Rotate instrument horizontally and make two

Leveling screws arbitrarily chosen parallel to the display.

②

Turn on the Electronic vial function by pushing the

Laser key.

Put the bubble of the Circular vial in the center of the circle when the display shows “TILT OVER”.

③ Turn two Leveling screws arbitrarily chosen in an opposite direction mutually and put the vial of the horizontal Electronic vial in the center. (Figure A)

④ Put the bubble of the lengthwise Electronic vial in the center by operating the Leveling screw of one remainder. (Figure B)

⑤

The procedures are different according to the state of the Automatic inclination correction as following.

[When using the Automatic inclination correction by 2 axes]

Please read procedure⑥because the horizontal angle and the perpendicular angle error by a perpendicular axis are automatically corrected.

[When using the Automatic inclination correction by 1 axis]

The instrument is horizontally rotated by 180° after the bubble of the Electronic vial is adjusted on the center at a Left circle position side and confirm that the bubble of the vial is at the center at the right circle position.

[When using without Automatic inclination correction]

Confirm the bubble is at the center even if the instrument is rotated by each 90°.

⑥

Confirm whether the plummet is on the ground mark. When you confirm it is not on the mark, loosen the center screw and move the instrument over the ground mark correctly and fix the instrument by a center screw. Repeat from ①to⑥.

3.6 Eyepiece adjustment

[Eyepiece adjustment]

The eyepiece adjustment is performed before target sighting.

①

Remove the telescope lens cap.

Vertical line (single)

② Point the telescope at a bright object, and rotate the eyepiece ring full counter clockwise.

Horizontal line

③ Look through the eyepiece, and rotate the eyepiece ring clockwise until the reticle appears at its maximum sharpness.

• When looking into the eyepiece, avoid an intense look to prevent parallax and eye fatigue.

• When it is hard to see the reticle due to poor

Sight axis

Vertical lines (double) brightness, press [ILLU] + [F3] [RETICLE] to access the RETICLE INTENSITY ADJ. screen. Use the left and right arrow to adjust the reticle intensity.

3.7 Target sighting

[Target sighting by Manual focus]

①

Loosen the telescope clamp and horizontal clamp screws.

② Point the telescope at the target using a collimator.

③

Tighten the above two screws.

④

Adjust the eyepiece.

⑤ Look through the telescope and then rotate the Focus ring and stop it where the target can be clearly seen and the target image does not move in relation to reticle even if your eye is vertically and horizontally moved.

⑥ Align the reticle accurately on the target using telescope and horizontal tangent screws.

Collimator

Target

Focus Ring

Collimator

Target sighting

• The Focus ring rotation “clockwise” makes it possible to focus on closer objects and

“counter clockwise” will focus on further objects.

3.8 Attachment and detachment of tribrach

The tribrach of R-202NEand R-205NE can be detached from the instrument, if required when replacing the instrument with a prism for example.

[Detachment]

First loosen the recessed screw with a screwdriver, then rotate the locking knob until the arrow points upward, and lift the instrument up.

[Attachment]

Mount the instrument on the tribrach with the guide marks coinciding, and rotate the locking knob until the arrow points downwards.

The guide and guide mark must be fitted to attach the instrument.

When the tribrach does not need to be attached or detached, or the instrument is to be transported, tighten the recessed screw with a screwdriver to fix the locking knob.

Guide mark

Recessed screw

Tribrach locking lever

4. TURNING THE POWER ON

4.1 Turning the Power On and Off

Pressing the [POWER] key shows the initialscreen.(The [POWER] key is also used to turn the power off.)After a few seconds, it turns to Electronic vial screen. Move the vials to center by adjusting the leveling screws.Pressing the [ENT] key views the angle and distance measurement screen.

● The Auto Power Off function will automatically turn the power off if no operations are performed for approximately 10 minutes. (Factory default setting)

● The [POWER] key is controlled by software in the instrument while it is working, and this key is valid only when turning off causes no problem.

●

The value displayed when the power was last time turned off will be displayed for the horizontal angle. If this horizontal angle is not needed, please perform horizontal angle

0 SET.

For details on resetting the horizontal angle 0 See "5-2".

For details on changing the horizontal angle from clockwise to counterclockwise See "5-6".

For details on measuring the vertical angle See "5-5".

For details on distance measurement See "6. ".

For details on the automatic power-off function See "8-9 ".

4.2 Adjusting LCD contrast

Press [F4] while holding down the Illumination key to access the screen for adjusting LCD contrast.

Pressing the [F1] [ ] will lighten the contrast, while pressing the [F2] [ ] will darken the contrast.

Press [ENT] to exit adjustment mode and return to the previous screen.

• Pressing the Illumination key views the [F3] [RETICLE], [F4] [LCD] and [F5] [ILLU].

• LCD contrast may be adjusted as necessary at any time.

• The contrast may be adjusted to any one of 25 levels.

• LCD contrast may be unappealing under certain environmental conditions such as high temperature. Adjust the LCD contrast as described above in such situations.

4.3 Adjusting illumination brightness

Press [F5] while holding down the Illumination key to access the screen for adjusting illumination brightness.

Pressing the [F1] [ ] will decrease brightness, while pressing the [F2] [ ] will increase brightness.

Press [ENT] to exit adjustment mode and return to the previous screen.

• Pressing the Illumination key views the [F3] [RETICLE], [F4] [LCD] and [F5] [ILLU].

• Illumination brightness of the LCD screen and telescope reticle may be adjusted as necessary at any time.

• Illumination brightness may be adjusted to any one of 10 levels.

4.4 Adjusting reticle illumination

Press [F3] while holding down the Illumination key to access the screen for adjusting reticle illumination. The procedure to adjust the reticle illumination is the same way as 4.3.

• Pressing the Illumination key views the [F3] [RETICLE], [F4] [LCD] and [F5] [ILLU].

5. ANGLE MEASUREMENT

5.1 Measuring an angle

Aim at the first target, then press [F3] [0 SET] twice in succession to reset the horizontal angle to 0.

Aim at the second target, then read the horizontal angle.

Pressing [F4] [DISP] displays the vertical angle.

• The [F3] [0 SET] key cannot reset the vertical angle to 0.

• Pressing the [F4] [DISP] key cycles through the sets of display items :

“H.angle/H.dst./V.dst.”, “H.angle/V.angle/S.dst.”, and

“H.angle/V.angle/H.dst./S.dst./V.dst.”.

• Even though you turn the power off during a survey, the horizontal angle displayed last time is saved, so that it is restored when the power is turned on next time.

• When the restored horizontal angle is not necessary, reset it to 0.

5.2 Resetting the horizontal angle to 0

Pressing [F3] [0 SET] twice in succession resets the horizontal angle to 0° 0' 0".

• The [F3] [0 SET] cannot reset the vertical angle to 0.

• Pressing the [F3] [0 SET] accidentally during measurement does not reset the horizontal angle to 0 unless you press it again. Once the buzzer stops sounding, you can go to the next step.

• You can reset the horizontal angle to 0 any time except when it has been held.

5.3 Holding the horizontal angle

To hold the horizontal angle currently being displayed, press [F3] [HOLD] twice in succession. The horizontal angle value is displayed in reverse video when being held.

• lf you want to hold the horizontal angle when you are in MODE A, press [F5] [MODE] first to switch to MODE B, then press [F3] [HOLD].

• The [F3] [HOLD] cannot hold the vertical angle or distance.

• To release the horizontal angle from being held, press [F3] [HOLD] once.

• Pressing [F3] [HOLD] accidentally during measurement does not hold the horizontal angle unless you press it again. Once the buzzer stops sounding you can go to the next step.

5.4 Inputting an arbitrary horizontal angle

In case of Horizontal angle 123° 45' 20" input.

Press [F5] [MODE] to enter MODE B.

Press [F2] [ANG SET] to display the ANGLE SET screen, then press [F4] [ ] to move the cursor to “2. H.ANGLE INPUT”.

Press [F5] [SELECT] to open the horizontal angle input window.

[F5] [CLEAR] is used to clear the values.

Press the numeric key as 123.4520.

Press the [ENT] key to accept the horizontal angle set to 123° 45' 20" and change the screen to MODE A.

• The former data is called by pressing the

[CLEAR] key again.

5.5 Displaying the slope % of the vertical angle

Press [F5] [MODE] to enter MODE B.

Press [F2] [ANG SET] to display the ANGLE SET screen.

Press the [F5] [SELECT] to change the screen to display the slope % of Vertical angle.

Press [F4] [DISP] to display the slope value in %.

• The 0% represents the horizontal 0, and +100% and -100% represent 45° up and down slopes respectively.

• To return the screen from the slope (%) display to the 360° scale, also take above same steps by entering MODE B.

• If the slope (%) exceeds [+/-] 1000%, “Out of grade range” is displayed, indicating that the current vertical angle cannot be measured.

• When the telescope returns to a slope within slope [+/-] 1000%, the slope (%) display returns automatically from the “Out of grade range” message to the numeric value.

5.6 Changing the horizontal angle from clockwise to counter clockwise

Press [F5] [MODE] to enter MODE B.

Press [F2] [ANG SET] to display the ANGLE SET screen.

Press [F4] [ ] to move the cursor to

“3. R/L REVERSE”.

Press [F5] [SELECT] to add a minus sign (-) to the horizontal angle value as a counter clockwise angle.

• To return the horizontal angle from counter clockwise to clockwise, also take the above same procedures, press [F5] [SELECT] to select the clockwise angle.

• When the counter clockwise horizontal angle is selected, the order of aiming at the targets becomes the reverse (the right one first, then the left one) of the order for the clockwise angle.

6. DISTANCE MEASUREMENT

6.1 Target setting

The target mode and its Constant of current setting are shown at the left of the battery mark. For example in case of each Constant 0, Reflectorless

(Non-Prism); N 0, Prism; P 0

Pressing [F2] [TARGET] changes the target mode.

• The target mode is changed sequentially as follows.

Reflector sheet - Prism - Reflectorless

• The selected target mode is stored in the memory even if the power is turned off.

So, next time you can use the same mode after turning on.

• The target Constant differs according to the selected target mode. So, confirm the target mode and its Constant shown at the top screen after changing the target.

[Distance measurement by reflectorless (Non-Prism) mode]

• The measurement range and accuracy of Reflectorless are based on the condition that laser beam is emitted perpendicular to the white side of the Kodak Gray Card. The measurement range may be influenced by the shape of the target and its environment. There is a possibility that the range may vary when the target does not satisfy the conditions above at survey work.

• Pay attention to the following in case of distance measurement by Reflectorless.

In case of resulting in low accuracy, perform the distance measurement by Prism.

• The CODE number 521 [LONG RANGE MES.] shows ON/OFF.

• The WARNING (Laser Power) screen is displayed when Message ON is selected, and then

[F1] [MEAS] key is pressed.

• Pressing [F1] [MEAS] one time selects “Second MEAS setting” and twice selects “QUIT”.

①

There is a possibility that correct distance measurement may be impossible by dispersion or reduction of laser beam when the laser beam comes into the target from diagonal angle.

②

There is a possibility that the instrument cannot calculate correctly when receiving reflected laser beam from forth and back directions in case of measuring the target on the road.

③ There is a possibility that synthesized values are calculated and the distance may become longer or shorter than the actual one when the operator measures the target of slope or sphere or rugged shape.

④ There is a possibility that the instrument cannot calculate correctly collecting the reflected laser beam from a man or a car that comes and goes in front of the target.

[Distance measurement by reflector sheet mode]

Position the Reflector sheet whose reflecting surface faces the aiming line to be approx. right angle when the distance is measured by it. If it is positioned not to be approx. right angle, there is a possibility that correct distance measurement may be impossible by dispersion or reduction of laser beam.

[Applied measurement range by each target mode]

• When a wrong target mode is selected, a correct distance cannot be measured.

Please select a correct target mode and measure.

• It is sometimes possible to measure without prism under special conditions like in the close distance, targeting on a wall surface. However, there is a possibility including some errors in this case, so be sure to select the reflectorless mode.

• The target constant should be correctly selected and confirmed in case that the reflector sheet is used at the prism mode and the prism is used at the reflector sheet mode.

6.2 Distance measurement

The R-200 series has two distance measurement modes of primary MEAS and second MEAS.

Pressing the [F1] [MEAS] one time goes to primary MEAS and twice goes to second MEAS.

You can freely select and allocate your desired measurement mode in primary MEAS and second MEAS by the initial setting 2. The “MEASURE SHOT” is set at primary MEAS and

“TRACK CONT” is set at second MEAS as a factory default setting.

• MEASURE SHOT means the distance measurement by the shot mode.

• MEASURE CONT means the distance measurement by the continuous mode.

• TRACK SHOT means the fast distance measurement by the shot mode.

• TRACK CONT means the fast distance measurement by the continuous mode.

Confirm the target constant before beginning the distance measurement.

Example: “MEASURE SHOT”at primary MEAS (Factory default setting)

Collimate the telescope at a target and press the [F1]

[MEAS] once to start measuring the distance. Once distance measurement has been started, the distance measurement mark remains displayed. Upon reception of a reflected light from the target, the instrument beeps and displays the mark to start the shot measurement automatically.

• If the instrument is in MODE B, press the [F5] [MODE] to switch to MODE A and press

[F1] [MEAS].

• Pressing the [F1] [MEAS] after collimating the telescope at the prism starts shot distance measurement with the “MEAS” text blinking. Distance measurement is completed and the

“MEAS” text stops blinking the moment the distance measured by shot measurement is displayed. During continuous measurement, the “MEAS” text keeps on blinking. Pressing the [F1] [MEAS] again terminates both distance measurement and blinking of the “MEAS” text.

• Pressing [F4] [DISP] cycles through the sets of display items:“H.angle/H.dst./V.dst.”,

“H.angle/V.angle/S.dst.”, and “H.angle/V.angle/H.dst./S.dst./V.dst.”

• Pressing the [ESC] or [F2] [TARGET] or [F5] [MODE] during distance measurement stops it.

• If the shot count for distance measurement has been set to 2 or more in “initial setting 2”, the distance is measured for the specified number of times to display the averaged value.

Example: “TRACK CONT” at second MEAS (Factory default setting)

Collimate the telescope at a Target and press [F1] [MEAS] twice to start measuring the distance. Upon reception of a reflected light from the target, the instrument beeps and displays the mark to start the TRACK distance measurement.

• If the instrument is in MODE B, press [F5] [MODE] to switch to MODE A and press [F1]

[MEAS ] twice.

• Pressing [F1] [MEAS] twice after collimating the telescope at the Target starts Continuous distance measurement at fast speed with the “MEAS” text blinking.

It remains blinking during the measurement. If you press the [F1] [MEAS] again, Distance measurement is completed and the “MEAS” text stops blinking.

• Pressing [F4] [DISP] cycles through the sets of display items:“H.angle/H.dst./V.dst.”,

“H.angle/V.angle/S.dst.”, and “H.angle/V.angle/H.dst./S.dst./V.dst.”

• Pressing the [ESC] or [F2] [TARGET] or [F5] [MODE] during fast distance measurement stops it.

6.3 Quick mode

The Quick Mode is to shorten the measuring time using prism or reflector sheet.

• The Quick Mode is to short the prism's measuring time.

• The Quick Mode is effective to measure the distance up to 500m using prism or reflector sheet.

• After selecting Quick Mode from the Quick Mode setting screen, the distance measurement is done in Quick Mode.

• If the Quick Mode is selected, the distance measurement mark, "<-<- ->->", instead of

"((( )))", is displayed

7. CORRECTION MODE

7.1 Changing the target constant

Changing the Target Constant can be performed only when the Reflector sheet and Prism

Constant setting are “INPUT” in initial setting 1.

Example: Prism Constant -25mm setting

Press [F4] [CORR] in MODE B.

(If the instrument is in MODE A,

press [F5] [MODE] to enter MODE B.)

Press the [F5] [SELECT] to enable the Prism Constant to be changed.

Clear the exiting values by pressing [F5] [CLEAR].

Input -25 by pressing the numeric keys.

Press the [ENT] key to accept the Prism

Constant to -25mm.

Pressing the [ENT] key returns the instrument to MODE A.

• To set the Reflector sheet constant to “0mm” select “0mm” for “SHEET CONST” in

“initial setting 1”.

• To set the Prism constant to“0mm” or “-30mm” select “0mm” for “PRISM CONST” in

“initial setting 1”.

• When the “Sheet Constant” has been set to “0mm” in “initial setting 1” and “PRISM

CONST” has been set to “0mm” or “-30mm”, “*” is displayed to the left of “0mm” or

“30mm” on the correction menu screen. When “*” is on the screen, the Constant cannot be changed (by entering a numeric key).

• Once set, the Reflector sheet Constant and Prism Constant remain on the measurement screen as “S 0” or “P 0”.

• The factory initial of Reflector sheet Constant and Prism Constant are 0.

• Once set, each Constant remains in memory even after the power is turned off.

7.2 Changing the temperature

The temperature setting can be changed only when “ATM CORR” has been set to “ATM

INPUT” in “initial setting 1”.

Example: Setting the temperature to +22°C

Press [F4] [CORR] in MODE B.

(If the instrument is in MODE A, press [F5] [MODE] to enter MODE B.)

Press [F4] [ ] to move the cursor to “3.TEMP” and press the [F5] [SELECT] to enable the temperature to be changed.

Clear the exiting values by pressing [F5] [CLEAR].

Input 22 by pressing the numeric keys.

Press the [ENT] key to accept the temperature to +22°C.

Pressing the [ENT] key returns the instrument to

MODE A.

• The valid range of Temperature input is from -30°C to +60°C.

• When “ATM CORR” in “initial setting 1” has been set to “4. NIL”, “*” is displayed to the left of the temperature value on the correction menu screen. When “*” is on the screen, the temperature cannot be changed. If “ATM CORR” in “initial setting 1” has been set to “3. ppm INPUT”, no temperature is displayed on the correction menu screen.

• Once set, the temperature is displayed at the centre of the top of the measurement screen.

• The factory initial of temperature is “+15°C”.

• Once set, the temperature remains in memory even after the power is turned off.

• Temperature correction is based on 15°C.

If this instrument is used without correcting the temperature, a distance error per 100m is about -0.1mm per +1°C as a temperature difference from 15°C.

A distance error per 100m is about 0.1mm per -1°C as a temperature difference from 15°C.

(For more accurate values, See “12.4 Error when no atmospheric correction is made”.)

7.3 Changing the atmospheric pressure

The atmospheric pressure setting can be changed only when “ATM CORR” has been set to

“ATM INPUT” in “initial setting 1”.

Example: Setting the pressure to 900hPa

Press [F4] [CORR] in MODE B.

(If the instrument is in MODE A, press [F5] [MODE] to enter MODE B.)

Press [F4] [ ] to move the cursor to “4.PRESS” and press the [F5] [SELECT] to enable the temperature to be changed.

Clear the exiting values by pressing [F5] [CLEAR].

Input 900 by pressing the numeric keys.

Press the [ENT] key to accept the

PRESS to 900hPa.

Pressing the [ENT] key returns the instrument to MODE A.

• The valid range of Pressure input is from 600 to 1120hPa (420 - 840mmHg) .

• When “Atmospheric Correction” in “initial setting 1” has been set to “3. NIL”, “*” is displayed to the left of the pressure value on the correction menu screen.

When “*” is on the screen, the pressure cannot be changed.

If “ATM CORR” in “initial setting 1” has been set to “2.ppm INPUT”, no pressure is displayed on the correction menu screen.

• Once set, the pressure is displayed at the centre of the top of the measurement screen.

• The factory initial of pressure is “1013hPa”.

• Once set, the pressure remains in memory even after the power is turned off.

• Pressure correction is based on 1013 hectopascals (hPa).

• If this instrument is used without correcting the pressure, a distance error per 100m is about

-0.3mm per -10hPa as a pressure difference from 1013hPa.

(For more accurate values, see “12.4 Error when no atmospheric correction is made”.)

7.4 Changing the ppm value

The ppm value can be changed only when “ATM CORR” has been set to “ppm INPUT” in

“initial setting 1”. “TEMP” and “PRESS” are not displayed.

Example: Setting the ppm value to 31 ppm.

Press [F4] [CORR] in MODE B.

Press [F4] [ ] to move the cursor to “3. ppm” and press the [F5] [SELECT] to enable the temperature to be changed.

Clear the exiting values by pressing [F5] [CLEAR].

Input 31 by pressing the numeric keys.

Press the [ENT] key to accept the

PPM to 31ppm.

Pressing the [ENT] key returns the instrument to MODE A.

• The valid range of ppm values is from -199 to +199.

• Once set, the ppm value is displayed at the centre of the top of the measurement screen.

• The factory initial of ppm value is “0”.

• Once set, the ppm value remains in memory even after the power is turned off.

8. INITIAL SETTING

8.1 Overview

For the R-200 series, you can select and save the desired setting for a variety of prescribed instrument conditions, called initial setting.

The Initial Setting is saved in four modes, “initial setting 1”, “initial setting 2”,, “initial setting

4”, and “initial setting 5” in which you can select and save the instrument conditions described below.

The factory default for each of these conditions is marked by .

To change initial setting, follow the operating procedures for entering each initial setting mode in “8.2” and the operating procedures for changing an initial setting in “8.2”.

8.2 Entering the mode for initial setting 1

Press the [POWER] key while holding [F1] key down to access the screen for initial setting 1.

1.ATM CORR

：ATM INPUT

2.PRISM CONST ：-30mm

3.SHEET CONST ： 0mm

4.CRV/REF CORR ：0.14

5.COMP AXIS

：ON

• Pressing [F1] [ △ ] scrolls it up five items; pressing [F2] [ ▽ ] scrolls the screen down five items.

• Press [F3] [ ] or [F4] [ ] to position

the cursor at the item of interest.

1.ATM CORR

：ATM INPUT

2.PRISM CONST ：-30mm

3.SHEET CONST

：0mm

4.CRV/REF CORR ：0.14

5.COMP AXIS

：ON

8.3 Entering the mode for initial setting 2

Press the [POWER] key while holding [F2] key down to access the screen for initial setting 2.

• Select the item of interest in the same way as in the mode for initial setting 2.

8.4 Entering the mode for initial setting 4

Press the [POWER] key while holding [F4] key down to access the screen for initial setting 4.

• Select the item of interest in the same way as in the mode for initial setting 4.

8.5 Entering the mode for initial setting 5

Press the [POWER] key while holding [F5] key down to access the screen for initial setting 5.

• Select the item of interest in the same way as in the mode for initial setting 5.

8.6 Example of changing an initial setting content

(selection of atmospheric correction)

This section describes the operating procedures for selecting “1.ATM CORR” in initial setting 1 as an example of changing an initial setting content. Use this example as a reference when changing other items because it is also applicable to the operating procedures for changing them.

Access the screen for initial setting 1 by taking procedures “8.2 Enter the mode for initial setting 1”.

1.AIM CORR

：ATM INPUT

2.PRISM CONST ：-30mm

3.SHEET CONST ： 0mm

4.CRV/REF CORR ：0.14

5.COMP AXIS ：ON

Press [F5] [SELECT] to open the screen for selecting the atmospheric correction.

1.ATM CORR

：ATM

4.CRV/REF CORR ：0.14

5.COMP AXIS

：ON

Press [F3] [ ] or [F4] [ ] to position the cursor at the desired item, then press [ENT] key to select that item.

Pressing the [ENT] key selects the change of selected item. Pressing the [ESC] key invalid

1.ATM CORR

：ATM

2.PRISM CONST ：-30 ㎜

3.SHEET CONST ： 0 ㎜ ates the change of selected item.

4.CRV/REF CORR ：0.14

5.COMP AXIS

：ON

Pressing again the [ESC] key or [ENT] key quits the initial setting screen and usual start screen appears.

1.ATM CORR

：pp INPUT

2.PRISM CONST ：-30mm

3.SHEET CONST ：0mm

4.CRV/REF CORR ：0.14

5.COMP AXIS ：ON

8.7 Initial setting 1

Selection of Atmospheric Correction:

By entering ppm value, or by fixing the ppm value to 0

(NIL) not to perform Atmospheric Correction.

1. Selection of Prism Constant: [PRISM CONST.]

Select whether the Prism Constant to be input is set to

0mm, -30mm or to an arbitrary value to be entered from the keyboard.

2. Selection for Reflector sheet Constant: [SHEET CONST]

Select whether the target constant to be input is set to 0mm, or to an arbitrary value to be entered from the keyboard.

3. Selection for Refraction & Curvature Corrections

: [CRV/REF CORR]

Select whether the correction factor to be input for both differences (Refraction, Curvature) is set to 0.14, 0.2 or none (NIL). Selecting “3. NIL” results in no correction of both values.

X 1.ATM INPUT

2. 0mm

3.INPUT

2.INPUT aXXX

2.ppm INPUT

3.NIL

1.-30mm

1. 0mm

1.0.14

2.0.2

3.NIL

XaXXXXXX

4. Selection of Tilt Compensation: [COMP AXIS]

Select whether Tilt Compensation is to be ON/OFF.

X 1.ON

XXXXXXX

2.OFF

• The factory default for each instrument condition is marked by .

8.8 Initial setting 2

1. Selection of the Shot count: [SHOT COUNT]

Select whether the shot count for Shot distance measurement is to be 1, 3, 5 or an arbitrary count to be entered.

2. Setting the Shot input: [SHOT INPUT]

Set the shot number for Shot distance measurement.

• The valid range of values for the shot number is from 1 to 99.

• This setting is enabled only when the shot number (Above 2.) has been set to “4. INPUT”.

X 1.1 TIME XXXXXXX

2.3 TIMES

3.5 TIMES

4.INPUT

0 1 TIMES

3. Selection of the quick measuring:ON/OFF

4. Selection of Long range message

: [LONG RANGE MES.]

5. Selection of Laser plummet : [LD PLUM.]

Laser plumb ON/OFF is selected.

6. Selection of Minimum angle display: [MIN UNIT ANG.]

Select whether to set the minimum angle display mode to

“COARSE (5 seconds)” or “FINE (1 second)”.

1.OFF

2.ON

1.OFF

2.ON

XaXXXXXX

X 1.OFF XaXXXXXX

2.ON

1.COARSE

2.FINE

XXXXXXXXX

7. Selection of Vertical angle style: [V.ANG. STYLE]

Select whether the 0 point for vertical angle is set to be

“Z.0”, “H.0” or “COMPAS”.

X 1.Z.0

2.H.0

3.COMPAS

XXXXX

8. Selection of Automatic power-off function

: [AUTO OFF]

Select the time interval (10, 20 or 30 minutes) for activating the automatic power-off function, or select NIL, disabling the function.

X 1.10 MIN XXX

2.20 MIN

3.30 MIN

4.NIL

• The automatic power-off function automatically turns the power supply off after the specified period of time (in minutes) when no operation for distance measurement or for key entry has been performed with the angle remaining unchanged.

9. Selection of Distance measurement automatic power-

off function: [EDM OFF]

Select the time interval (3, 5, or 10 minutes) for activating the distance measurement automatic power-off function, or select

NIL, disabling the function.

10. Selection for H.angle 90° buzzer: [QUAD. BUZ]

Select whether to enable or disable the beep at every 90° during angle measurement.

X 1. 3 MIN XXX

2. 5 MIN

3.10 MIN

4.NIL

X 1.OFF

2.ON

XaXXXXXX

8.9 Initial setting 4

1. Selection of Temperature unit setting: [TEMP. UNIT]

Select °C or °F as the unit for Temperature.

2. Selection of Pressure unit setting: [PRESS UNIT]

Select hPa (hectopascal), mmHg, inchHg as the unit for pressure to be input.

2.ﾟ F

1.ﾟ C XXXXXXXXXX

1. hPa

2. mmHG

3.inchHG

XXXXX

3. Selection of Distance unit setting: [DIST. UNIT]

Select m or ft or ft+inch as the unit for Distance.

4. Selection of Angle unit setting: [ANG. UNIT]

Select DEG or DEC or GRD or MIL as the unit for Angle.

8.10 Initial setting 5

1. Selection of Transfer rate (baud rate): [BAUD UNIT]

Select a baud rate of 1200, 2400, 4800 or 9600.

2. Selection of Data bits: [DATA LENGTH]

Select a data length of 8 bits.

3. Selection of Parity: [PARITY BITS]

Select no (NIL) parity bit, even parity or odd parity.

4. Selection of Stop bits: [STOP BITS]

Select the number of stop bits to be used: 1 or 2.

5. Selection of Control signal: [SIGNAL CONTROL]

Select whether the control signal is effective or not.

6. Selection of XON/XOFF: [XON/XOFF]

Select whether to enable or disable XON/XOFF.

7. Selection of Through command

: [THROUGH COMMAND]

Select whether to disable data output without receiving any data request command or enable the “a” to “f” command data output.

X 1.m XXXXX

2.ft

3.ft+inch

X 1.DEG XXX

2.DEC

3.GRD

4.MIL

X 1.1200 XXX

2.2400

3.4800

4.9600

X 1.8

XXXXXXXXXXXX

X 1.NIL XXXXX

2.EVEN

3.ODD

X 1.1 XaXXXXXX

2.2

X 1.ON XaXXXXXX

2.OFF

X 1.ON XaXXXXXX

2.OFF

X 1.NIL

XXXXXXXXXX

2.a

3.b

4.c

5.d

6.e

7.f

9. ACCESSING THE FUNCTIONS

9.1 Accessing by help key

You can use the [HELP] key to display specific

initial setting (such as the prism constant and

atm corr).

Press the [ILLU]+[ESC] key in MODE A or B.

1 、 H E L P

2、401TARGET CONST：-30mm

3、402ATM CORR ：ATM INPUT

4、502SHOT COUNT

5、503CRV/REF CORR：0.14

The help menu will then be displayed. Press [F1] [ △ ][F2] [ ▽ ] or [F3] [ ] [F4] [ ] to position the cursor to the desired item.

9.2 Accessing by 007

The R-200 allows you to enter a special code of 007 with the alphanumeric keys to display specific initial setting.

Press the numeric keys [0] [0] [7] in MODE A or B.

The screen will then change to the command input screen.

Press the numeric keys for the desired command number in the Command No. Table.

(For example, press [4] [0] [1] for TARGET

CONST.)

Press the [ENT] key to access the TARGET

CONST.

[Instrument setting items]

007 HELP menu list

401 TARGET CONST

402 ATM CORR

502 SHOT COUNT

503 CRV/REF CORR.

504 MIN UNIT ANG.

505 V.ANG. STYLE

509 QUAD BUZ.

510 AUTO OFF

511 EDM OFF

517 COMPENSATOR

520 LD. PLUM.

PRISM CONST

SHEET CONST

SHOT COUNT

SHOT INPUT

Default

-30mm

0mm

ATM INPUT

1TIME

01TIMES

0.14

FINE

Z.0

OFF

10 MIN

OFF

521 LONG RANGE MES.

522 QUICK MEASURE

523 ATM CORR DISP

701 ATM UNIT TEMP. UNIT

PRESS UNIT

702 DIST. UNIT

703 ANG. UNIT

801 SETUP COM. BAUD RATE

DATA LENGTH

PARITY BITS

STOP BITS

SIGNAL CONTROL

XON / XOFF

THROUGH COMMAND NIL m

DEG

1200

NIL

(when target is

Ref.less)

OFF

ﾟ C hPa

Other options

0mm, INPUT

INPUT ppm INPUT, NIL

3TIMES, 5TIMES, INPUT

(input)

0.2, NIL

COARSE

H.0, COMPAS

20 MIN, 30 MIN, NIL

OFF

ﾟ F mmHg, inchHg ft, ft+inch

DEC, GRD, MIL

2400, 4800, 9600

EVEN, ODD

OFF

OFF a, b, c, d, e, f

10. CHECKS AND ADJUSTMENTS

• Checks and adjustments should be performed before and during measurement.

• The instrument should be checked after long storage and transportation.

• The checks should be performed in the following order.

[Cautions on CHECKS AND ADJUSTMENTS]

• When adjustment is completed, be sure that adjusting screws are completely tightened.

When finishing turning adjusting screws, be sure that screws are turned in a direction for tightening.

• Repeat check after adjustment, and check if the instrument has been adjusted properly.

• When adjustment is completed, be sure that adjusting screws are completely tightened.

When finishing turning adjusting screws, be sure that screws are turned in a direction for tightening.

• Repeat check after adjustment, and check if the instrument has been adjusted properly.

10.1 Plate level

[Checks]

① Align the Electronic vial in parallel with a line joining any two of the leveling screws. Then, adjust the two screws to center the bubble in the Electronic vial.

②

Turn two leveling screws in an opposite direction mutually and have the bubble of the side of the electronic vial to the center.

③

Make the bubble of the length of the electronic vial to the center by operating the leveling screw of one remainder.

④

Rotate the instrument by 180° and confirm the position of the bubble of the electronic vial. At this time, it is not necessary to adjust it if the bubble of the electronic vial is in the vicinity of the center.

●

Please check the electronic vial in a steady environment that has no vibration or rapid temperature change.

●

When the electronic vial is checked outdoors and on a tripod, avoid sunlight influence by using a sunshade. Please wait for a while until the instrument and tripod are at the same temperature as the surrounding air.

●

When the instrument is seen at the position of “Left circle”, movement and the inclination of the instrument become the same on the screen in the electronic vial. Please note that the movement of the bubble becomes opposite direction if it is seen at the position of “Right circle”.

10.2 Circular vial

Checks

① Adjust by the electronic vial beforehand.

②

Confirm the position of the bubble of the Circular vial.

At this time, it is not necessary to adjust if the bubble is at the center of the circle.

Adjustments

When the bubble of the Circular vial comes off from the center according to check procedure

② , it is necessary to adjust.

Turn the bubble adjustment screw with a hex wrench (L type wrench) and put the bubble in the center of the circle.

Circular vial

Plate level

Bubble adjusting screw

Circular vial adj. screw

● Tighten the screws equally after the above adjustment.

10.3 Vertical reticle

Checks

① Set the instrument up the tripod and carefully level it.

②

Sight the target Point A with telescope.

③

Using the telescope fine adjustment screws, move Point A to the edge of the field of view by screw (point A’).

④

No adjustment is necessary if Point A moves along the vertical line of the reticle.

Adjustments

① If Point A is off from the vertical line of the reticle, first remove the eyepiece cover.

②

Using the adjusting pin, loosen the four reticle adjustment screws slightly loosening each screw by the same amount, and then rotate the reticle line around the sight axis and align the vertical line of the sight axis with Point A’.

③ Tighten the reticle adjustment screws again by the same amount, and repeat the check to make sure the adjustment is correct.

Reticle adjusting screws

10.4 Perpendicularity of line of sight to horizontal axis

Checks

①

Position a target Point A at a distance 30m - 50m away from the instrument, and sight it with the telescope.

②

Loosen the telescope lock screw and turn the telescope until a point is sighted at a distance roughly equal to that of Point A. This is Point B.

③

With the telescope still reversed loosen the horizontal lock screw and rotate the instrument around the vertical axis, and sight Point A again.

④

Loosen the telescope lock screw and turn the telescope until a point is sighted at a distance equal to that of Point B. This is Point C.

⑤

No adjustment is necessary if Point B and C are aligned.

Adjustments

①

If Points B and C are not aligned, mark Point D at 1/4 the length of the BC, from Point C in the direction of Point B.

②

Using the adjustment pin, rotate the reticle adjustment screws horizontally opposite each other (see preceding page), and move the reticle to sight Point D.

①

Repeat the check and make sure the adjustment is correct.

10.5 Vertical 0 point error

Make sure to follow check procedures mentioned below after making adjustments on reticle and perpendicularity of line of sight to horizontal axis.

[Checks]

①

Set up the instrument and turn the power on.

② Sight the telescope at any reference target A at Normal state. Read the vertical angle (y).

③ Turn the telescope and rotate the alidade. Sight the same target A again at Back state and read the vertical angle R.

If y+R = 360°, no further adjustment is necessary.

[Adjustments]

If the deviation d (y+ R - 360° ) is wide, contact your local dealer.

10.6 Laser Plummet

Checks

① Set the instrument on the tripod, and place a piece of white paper with a cross drawn on it right under the instrument.

② Press the [LASER] key, and move the paper so that the intersecting point of the cross comes to the center of the Laser mark.

③ Rotate the instrument around the vertical axis, and observe the center mark position against the intersecting point of the cross at each 90° rotation.

④ If the Laser mark always coincides with the intersecting point, no adjustment is necessary.

Adjustments

When a center part where a cross intersection and the laser mark look the brightest shifts by

0.8mm or more (at the instrument height 1.5m), it is necessary to adjust it. A repair engineer does this adjustment. Please contact the PENTAX dealer.

10.7 Optical Plummet

Checks

① Set the instrument on the tripod, and place a piece of white paper with a cross drawn on it right under the instrument.

② Look through the optical plummet, and move the paper so that the intersecting point of the cross comes to the center of the field of view.

③ Adjust the leveling screws so that the center mark of the optical plummet coincides with the intersecting point of the cross.

④ Rotate the instrument around the vertical axis. Look through the optical plummet each 90° of rotation, and observe the center mark position against the intersecting point of the cross.

⑤ If the center mark always coincides with the intersecting point, no adjustment is necessary.

Adjustments

①

If the center mark does not coincide with the intersecting point, rotate the optical plummet focusing knob cover and remove it.

②

Mark the point set on the line of sight at each step of 90° on the white paper and call them A, B, C and D.

③

Join the opposed points (A,C and B,D) with a straight line, and set the intersecting point 0.

④

Turn the four optical plummet adjusting screws with a adjusting pin so that the center mark coincides with the intersecting point 0.

⑤ Repeat from ④ and check that adjustment is correct.

10.8 Offset Constant

The offset constant rarely changes. It is recommended, however, that check be done once or twice a year.

The check of the offset constant can be done on a certified base line. It can also be obtained in a simple way as described below.

Checks

1. Locate points A, B and C at about 50m intervals on even ground.

2. Set up the instrument at point A, and measure the distances between AB and AC.

3. Set up the instrument at point B, and measure the distance BC.

4. Obtain the offset constant (K):

K=AC - (AB+BC)

Adjustments

●

Contact your local dealer for adjustment of the off-set constant when the

K is not nearly 0.

10.9 Beam axis and Line of sight

Be sure to check that the beam axis and line of sight are aligned when the adjustments on reticle and perpendicularity of line of sight to horizontal axis are made.

Checks

① Set the prism at a distance greater than 50 m.

②

Accurately sight the center of the prism through the telescope.

③

Turn the power on and press (MEAS) to measure.

④ No adjustment is necessary if beam receiving buzzer sounds immediately and measurement value is displayed in a few seconds.

Adjustments

●

If instrument function is not as described in ④, contact your local dealer.

● This check should be done under good weather conditions.

10.10 The EDM beam axis

The distance measurement (EDM) beam axis is adjusted to be aligned to the sighting axis of the telescope, but it can be changed a little in case of rapid temperature change, shock or aging. Check your instrument by following procedures.

Checks

①

Install the instrument on the tripod and level it at the distance of approx.

50 m from the wall.

②

Displace the target plate attached to the end of this manual. Place the target plate adjusting its center to the center of telescope cross line and to be about horizontal to the instrument.

③ Turn the power on, and confirm the [TARGET] is set to the Reflecting sheet mode (“S” will be indicated at the top of display, left side of the battery remains sign when it is that.)

When it is not, press [F2] [TARGET] and set to Reflecting sheet mode (Reference p38 6.1

Target Setting).

④

Press [F1] [MEAS], then the laser spot appears on the target plate. If the “Center” of the laser spot is within the internal circle (10mm) of the target plate at this moment, the adjustment is unnecessary.

●

The laser spot disappears in approx. 20 seconds after pressing [F1][MEAS].

Press [MEAS] again, if it is necessary.

Adjustments

At the procedure 4. above, if the “Center” of laser spot is not within the internal circle (10mm) of the target plate, the adjustment is necessary. Please contact your PENTAX dealer.

11. SPECIFICATIONS

R-202NE

Telescope

Image Erect

Optical aperture 45mm

EDM aperture

Reticle illumination

Pointer

45mm

Intensity settings: 10 steps

Visible la ser

R-205NE

Resolving power 3”

Field of view 2.6% (1° 30’)

Minimum focus 1.0m

Focus Manual

Distance measurement

Laser Class Visible Laser: Class II (2) / Class IIIa (3R) -Long range mode in Reflectorless

Measurement range (Good condition)

Reflectorless 270m

Mini prism

1.5m - 1100m (40km)

1.5m - 3000m (20km)

200m - 4000m (20km)

Accuracy

Measuring time

Repeat meas.

Initial meas.

Normal :Prism, 2.0sec. ( 1 mm)

Prism, 0.4sec. ( 1 cm)

1.2 sec. ( 1 mm) *Quick mode

Normal : Prism, 2.4sec. (1mm )

Normal :Prism, 2.5sec. (1mm ) *Quick mode

Angle measurement

Measuring method

Absolute rotary encoder

Minimum count 1” / 5”

Accuracy 2” 5”

Sensitivity of vials

Plate level

(electronic)

30”/1div.

Circular level 8’/2mm

Plummet Visible Laser, ±0.8 mm (instrument height 1.5m)

Base Detachable

Water resistant IP54

Ambient temperature

Tripod thread

-20°C ~ +50°C / -4°F ~122°F (Working range)

5/8” x 11

Dimensions/Weight

Instrument 172(W) x 343(H) x 177(L) mm

Weight Approx.380g

Weight 280g

Carrying case 250(W) x 365(H) x 425(L) mm

Battery pack BP02C

Power source Ni-MH (Rechargeable)(4300mAh)

Operation time Continuous Approx. 5 hrs (ETH+EDM),12 hrs (ETH) with Approx. 2.2 hrs of charging time

Weight 280g

Internal Memory

Coordinates 20000 points data

Note: z The measurement range and accuracy of Reflectorless are determined by the white side of the Kodak Gray Card. z The measurement range may be influenced by the shape of the target and its environment. z

Quick mode, which functions with prism , is effective only under normal mode(1mm) and up to

500m.

z When Quick Mode is on, the EDM accuracy using Prism is ±(3+2ppm x D)mm. z EDM Measuring time varies according to distance to be measured and conditions of the environment.  z Normal conditions: 20km visibility with slight shimmer. z Good conditions: 40km visibility, overcast, no heat, no shimmer and moderate wind. z

The measurement time in reflectorless mode is influenced by the share, size and surface area and reflection rage of the target and its environment.

Maximum number of point to be recorded per job site : 3000 points

Maximum number of job file to be recorded : 50 job files

12. DATA COLLECTOR

The instrument can communicate directly with a computer through the RS232C interface. By use of a data collector you can automate data entry from the collection of survey data to the transfer of the data to a computer. This is useful in saving time and protecting data integrity.

● About connection with data collector and the handling, please refer to an “Instruction manual” of the data collector.

● Connecting a data collector to a computer is different with every system.

Please contact your local dealer about them.

13. APPENDIX

13.1 Error Messages

Message

Out of tilt range

Excess data

Mismatched

Target

Target is too close.

Unsuitable

Condition

Meaning

Displayed when the instrument is tilted beyond the vertical comp ensation range

(±3') in case 1 axis automatic compensation is selected. This messagemay be temporarily displayed if the instrument is turned too fast.

The input data exceeds the allowable range.

●

The distance is measured by Prism at

Reflector sheet mode, and the distance is over than 1000m.

●

The distance is measured by Prism or

Reflector sheet at Reflectorless mode, and the distance is over than

200m.

● The measurement distance is less than 1.5m at Reflector sheet mode.

● The measurement distance is less than 1.5m at Prism mode.

●

Under too strong sun light.

● Unstable light value owing to shimmer or obstacles.

● Reflector sheet, Target and Prism do not face the instrument.

●

Reflector sheet, Target and Prism are not correctly sighted.

●

Measurement range is over at

Reflectorless mode.

●

Sufficient signal does not return by sighting sharp edge etc. at

Reflectorless mode.

Distance measurement system problem ERROR!!

EDM ERROR 04

-05, 34-39, 50-53

ERROR!!

ETH ERROR 70-

ERROR!!

ETH ERROR 19

ERROR

S DATA of EDM

ERROR

P DATA of EDM

ERROR

ETH DATA

Li-batt.voltage is low

Angle measurement system problem

Memory problem

Problem of the internal EDM parameters

Problem of the internal ETH parameters

The Date Clock is powered by the built-in lithium battery. The lithium battery needs to be replaced in five years. The timing of battery replacement varies depending on the frequency of use and the environment of where the instrument is stored while not in use.

What to do

Re-level the instrument. Repair is needed if the message is displayed when it is properly leveled.

Press the [ESC] key and enter the correct data.

Select the correct target mode.

Select a longer point, or use a tape measure.

Change the object that has much better reflectivity, or use a reflecting sheet, or wait until the sun activity has weakened.

Turn the power off, and then turn on again.

Repair is needed when the message appears consistently.

Have the lithium battery replaced by the dealer from whom the instrument was purchased.

13.2 Atmospheric Correction

The speed at which light travels through the air varies depending on the temperature and atmospheric pressure. The R-200 series is designed to measure distances at the speed of light in order to measure accurately, Atmospheric Correction needs to be used. The instrument is

designed to correct for weather conditions automatically if the temperature and pressure are input. Correction is then carried out based on the following formula.

K: Atmospheric Correction Constant

P: Atmospheric pressure (hPa) t: Temperature(°C)

Distance after Atmospheric Correction D = Ds (1+K)

Ds: Measured distance when no Atmospheric Correction is used.

13.3 hPa and mmHg Conversion Table

Converting from hPa to mmHg hPa 0 10 20 30 40 50 60 70 80 90 mmHg mmHg mmHg mmHg mmHg mmHg mmHg mmHg mmHg mmHg

500 375 383 390 398 405 413 420 428 435 443

600 450 458 465 473 480 488 495 503 510 518

700 525 533 540 548 555 563 570 578 585 593

800 600 608 615 623 630 638 645 653 660 668

900 675 683 690 698 705 713 720 728 735 743

1000 750 758 765 773 780 788 795 803 810 818

1100 825 833 840 848 855 863 870 878 885 893

1200 900 908 915 923 930 938 945 953 960 968

Converting from mmHg to hPa mmHg 0 10 20 30 40 50 60 70 80 90

hPa hPa hPa hPa hPa hPa hPa hPa hPa hPa

400 533 547 560 573 587 600 613 627 640 653

500 667 680 693 707 720 733 747 760 773 787

600 800 813 827 840 853 867 880 893 907 920

700 933 947 960 973 987 1000 1013 1027 1040 1053

800 1067 1080 1093 1107 1120 1133 1147 1160 1173 1187

900 1200 1213 1227 1240 1253 1267 1280 1293 1307 1320

13.4 Error when no Atmospheric Correction is made

When measurement is carried out with no Atmospheric Correction (with the settings fixed at a temperature of 15°C and an atmospheric pressure of 1013 hPa or 760 mmHg), the Error per

100 meters in temperature and pressure will be shown in the tables below.

●

When the actual pressure is 1013 hPa (760 mmHg) and the temperature is 25°C, conducting the measurement with the temperature left at 15°C will result in the measurement being short by 0.9 mm per 100 meters.

Error table: When hPa (15°C, 1013hPa as standard)

C°

Unit:mm hPa

1200 1100 1013 900 800 700 600 500

45 2.0 -0.5 -2.6 -5.5 -8.0 -10.5 -13.0 -15.5

15 5.2 2.4 -0.0 -3.1 -5.9 -8.6 -11.4 -14.2

-15 9.0 5.9 3.2 -0.2 -3.3 -6.4 -9.5 -12.6

Error table: With mmHg (15°C, 760mmHg as standard)

C°

Unit:mm mmHg

900 800 760 700 600 500 400

15 5.2 1.5 0.0 -2.2 -5.9 -9.6 -13.3

13.5 Atmospheric Refraction and Earth Curvature

Correction

● Atmospheric refraction and earth curvature correction refers to correcting both the bending of the light beam caused by atmospheric refraction and the effect on the height differential and horizontal distance caused by the earth curvature.

●

Correction called “atmospheric refraction and earth curvature correction” is initiated to correct error when the slope distance and vertical angle are caused to determine the horizontal distance and the height differential, with this instrument, the following formula is used to correct these factors.

● Calculation formula when atmospheric refraction and earth curvature correction parameter is set to “ON”:

Corrected horizontal distance (H)

Corrected vertical distance (V)

●

Calculation formula when atmospheric refraction and earth curvature correction parameter is set to “OFF”:

S: Slope distance

α: Vertical angle from horizontal

K: Atmospheric refraction coefficient (0.14 or 0.2)

Re: Diameter of earth (6,370 km)

13.6 Distance Range

Generally speaking, the maximum range which can be measured varies considerably depending on the atmospheric conditions. For this reason, the Specifications illustrate the values for both Good and Normal weather conditions.

It is extremely difficult to judge when weather conditions are “Good” and when they are

“Normal”.With this instrument, the conditions noted below are used to differentiate between the two situations, (Good weather conditions for surveying are different from Normal weather conditions, and in surveying situations, cloudy skies are considered more favorable than sunny skies.)

Weather conditions for measurement ranges are based on the following standard values:

Normal: Visibility of approximately 20 km, with slight shimmer and moderatewind.

Good: Visibility of approximately 40 km, overcast, with no shimmer and moderate wind.

14 NOTICE TO THE USER OF THIS PRODUCT

To assure compliance with the Safety standard 21 CFR, Chapter 1. Subchapter J.

The U.S. bureau of Radiological Health requires the following information to be provided to user.:

It can be dangerous to look into the beam with optical equipment such as binoculars and telescopes.

1) Specifications of Laser Radiation

A) The EDM module of the R-200 produces a visible light beam, which is emitted from the telescope objective lens and the center hole of the instrument base plate. The R-

200 is designed and built to have a laser diode radiating at 620-690 nm.

B) Radiant power

The R-200 is designed and built to radiate a maximum average radiant power of

4.75mw. (0.95mw for the model without “NE”) from the telescope, and 0.95mw from the center hole of the base plate. The user may be subject to this radiation as a beam while operation until such time that the instrument is turned off.

2) The following labels are affixed to and must remain attached to this laser product.

A) The following Certification label is located near the Plate level.:

“This laser product is complied with the provisions of 21 CFR 1040. 10 and 1040.11.

For a Class II laser product.”

Or for R-200 models:

“This laser product is complied with the provisions of 21 CFR 1040. 10 and 1040.11.

For a Class IIIa laser product.”

B) Caution label is located near the exit aperture :

“AVOID EXPOSURE Laser radiation is emitted from this aperture.”

C) Warning logotype is located on the surface of the telescope:

“CAUTION LASER RADIATION DO NOT STARE INTO BEAM”

Or for R-200 models:

“DANGER LASER RADIATION AVOID DIRECT EYE EXPOSURE”

D) Warning label is Located near the exit aperture.

3) Caution to maintain the safety in compliance with the standard

A) To maintain the safety standard, refrain from any operation, maintenance, or adjustment other than described in this instruction manual.

B) Operation, maintenance or adjustment other than those specified in this instruction manual may result in hazardous radiation exposure.

C) Maintenance and repair not covered in this manual must be done by an authorized

Pentax dealer.

D) The Laser beam emission by the Distance measurement can be terminated by pressing F1 MEAS key.

E) Pressing Laser key

→F2 LD POINT key can terminate the laser beam emission by the laser pointer.

F) The Laser beam emission by the Laser plummet can be terminated by pressing Laser key.

TI Asahi Co., Ltd.

International Sales Department

4-3-4 Ueno Iwatsuki-Ku, Saitama-Shi

Saitama, 339-0073 Japan

Tel.: +81-48-793-0118

Fax. +81-48-793-0128

E-mail: [email protected]

www.pentaxsurveying.com/en/

Japan Surveying Instruments Manufacturers’ Association

Member symbol of the Japan Surveying

Instruments Manufacturers’

Association representing the high quality surveying products.

The duplication, reuse or sale of any information provided on this manual including but not limited to images, is strictly prohibited without expressed permission from the copyright owners.

Hallo! Ik ben een AI-chatbot die specifiek is getraind om u te helpen met de Pentax R-200 R-202NE. Ik heb het document grondig doorgenomen en kan u helpen de exacte informatie te vinden die u nodig heeft of de inhoud in duidelijke en eenvoudige bewoordingen uit te leggen. Of u nu op zoek bent naar begeleiding bij specifieke functies, stappen voor probleemoplossing of algemeen gebruik, stel gerust uw vragen. Hoe meer details u verstrekt over uw zorgen of behoeften, hoe nauwkeuriger en effectiever ik u kan helpen!

Assistent aan het typen

Assistent is niet meer aan het toetsenbord. Probeer het later opnieuw.

Het lijkt erop dat u een document hebt bereikt dat in meerdere talen is geschreven, waaronder een die niet uw moedertaal is. U kunt de volgende links gebruiken om tijdelijk pagina''s te verbergen zonder de taal van uw voorkeur.

Advertentie

total station

serIes

InstructIon manual

Basic Procedures

TI Asahi Co., Ltd.

CONTENTS

Exemption clause

PRECAUTIONS REGARDING SAFETY xx

Safety precautions (Must be followed)

Distinctive displays

WARNING

CAUTION

WARNING

CAUTION

USAGE PRECAUTIONS

[Solar observation]

WARNING

[Laser beam]

[EDM axis]

[Target constant]

[Reflectorless and reflector sheet]

[Battery & charger]

[Storage and operating environment]

[Transporting and carrying the instrument]

[Checks and repairs]

1. BASIC OPERATION

1.1 Names of parts

1.2 Unpacking and packing

[Unpacking the Instrument from the case]

[Packing the instrument in the case]

1.3 Standard equipment

1.4 Removing and attaching the Battery

[Removing the Battery]

·

[Attaching the Battery]

Remaining Battery Charge

[Charging the battery]

[Connection of code]

[Installation of battery]

[Detaching the battery]

[Display panel]

[How to charge]

[Refreshing the battery]

[Refreshing]

[Time of refreshing and charge]

2. DISPLAY AND KEYBOARD

2.1 Display and keyboard

2.2 Operation keys

2.3 Function keys

[Other functions]

[How to move the menu number]

2.4 Alphanumeric input

2.5 LD POINT, Laser pointer

3. PREPARATION FOR SURVEYING

3.1 Centring and Levelling of the Instrument

[Setting up the instrument and the tripod]

3.2 Laser plummet

[Laser plummet model]

[For the Detaching type laser plummet equipment model]

[For the Shift type laser plummet equipment model]

[Brightness adjustment of laser]

3.3 Optical plummet (Option)

[Detachable type]

[Shift type]

3.4 Levelling with circular vial

3.5 Levelling with the plate vial

[Leveling]

3.6 Eyepiece adjustment

[Eyepiece adjustment]

3.7 Target sighting

[Target sighting by Manual focus]

3.8 Attachment and detachment of tribrach

[Detachment]

[Attachment]

4. TURNING THE POWER ON

4.1 Turning the Power On and Off

4.2 Adjusting LCD contrast

4.3 Adjusting illumination brightness

4.4 Adjusting reticle illumination

5. ANGLE MEASUREMENT