installation instructions

installation instructions
Accessory
INSTALLATION
INSTRUCTIONS
Application
Publications No.
AII 19306
CD PLAYER
ATTACHMENT KIT
1998 ODYSSEY
Issue Date
NOV 1997
PARTS LIST
INSTALLATION
CD Player Attachment:
P/N 08B10-SX0-100
1. Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
CD Player bracket
2. Disconnect the negative cable from the
battery.
3. Open the coin box.
CONNECTOR
2 Bolts, 5 x 10 mm
(not used)
CD Player (sold separately):
P/N 08A06-181-220
CD Player
DASH LIGHTS
BRIGHTNESS
CONTROLLER
CLIP
4 Washer-screws,
4 x 8 mm
DASHBOARD
LOWER COVER
SELF-TAPPING
SCREWS
Owner’s Manual
4. Remove the dashboard lower cover (three
self-tapping screws, seven retaining clips, and
one connector).
Wire tie (not used)
TOOLS REQUIRED
#2 Phillips screwdriver
Stubby Phillips screwdriver
 1997 American Honda Motor Co., Inc. – All Rights Reserved
Y0462-D
08B10-SX0-1000-91
1 of 4
5. Open the glove box. Remove the self-tapping
screw that attaches the glove box damper to
the glove box.
9. Remove the beverage holder (four selftapping screws).
STOPPER ARM
GLOVE BOX
DAMPER
CLIPS
SELF-TAPPING
SCREWS
BEVERAGE HOLDER
GLOVE BOX
SELF-TAPPING
SCREW
10. Remove the two bolts attaching the radio to the
radio bracket, then pull the radio out toward
you. Unplug the 16-pin connector and the
antenna lead from the rear of the radio, and
remove the radio.
6. Remove the right and left stopper arms by
releasing the retaining clips.
ANTENNA LEAD
7. Open the center pocket in the center console,
and remove the seven self-tapping screws.
CLIP
16-PIN
CONNECTOR
CENTER
POCKET
SELF-TAPPING SCREW
CIGARETTE
LIGHTER
CONNECTORS
BOLTS
(Reuse.)
CENTER CONSOLE
8. Release the three retaining clips, and unplug
the cigarette lighter connectors; then remove
the center console.
2 of 4
AII 19306 (9711)
 1997 American Honda Motor Co., Inc. – All Rights Reserved
11. Remove the self-tapping screws attaching the
brackets to the pocket, and separate the
pocket from the radio.
RADIO
13. Slide the CD player into the radio opening in
the dashboard, and rest the CD player bracket
on the radio bracket. Route the DIN cable from
the CD player into the instrument panel under
and around the radio bracket.
CD PLAYER
BRACKET
Rest
RADIO
BRACKET
CD PLAYER
BRACKET
POCKET
SELF-TAPPING
SCREWS
12. Position the CD player bracket from the kit on
the rear of the CD player, and then install the
two 4 x 8 mm washer-screws furnished with the
CD player kit.
DIN CABLE
RADIO
BRACKET
CD PLAYER
CD PLAYER
BRACKET
4 x 8 mm
WASHER-SCREWS
 1997 American Honda Motor Co., Inc. – All Rights Reserved
AII 19306 (9711)
3 of 4
14. Before installing the radio, plug the DIN
connector from the CD player into the CD
changer connector on the rear of the radio.
Plug the 16-pin connector of the vehicle
harness and the antenna lead into the rear of
the radio. Then install the radio into the
dashboard opening above the CD player:
• Before the radio is installed completely, pull
out the CD player and align the face panels
flush with each other. Then push them in all
the way until their brackets rest on the radio
bracket properly without disturbing their
alignment.
• Make sure the DIN cable is not pinched
between the radio and the CD player.
16. Reinstall all removed parts.
17. Check that all wire harnesses are routed
properly and all connectors are plugged in.
18. Reconnect the negative cable to the battery.
19. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
20. Reset the clock.
21. Check the operation of the CD player
according to the Owner’s Manual supplied with
the CD player.
• Do not push in on the control switches or
knobs.
16-PIN CONNECTOR of
VEHICLE WIRE HARNESS
RADIO
ANTENNA
LEAD
CD CHANGER
CONNECTOR
CD PLAYER
DIN CABLE
5 x 10 mm
BOLTS
15. Install the two 5 x 10 mm bolts, and tighten
them securely.
4 of 4
AII 19306 (9711)
 1997 American Honda Motor Co., Inc. – All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement