Technisonic TFM-550 Airborne Transceiver Installation and Operating Instructions
Below you will find brief information for Airborne Transceiver TFM-550.
Advertisement
Advertisement
VHF High/VHF Low/UHF
MULTI-BAND FM
AIRBORNE TRANSCEIVER
MODEL TFM-550
Installation and
Operating Instructions
Til Document No.
99RE262
Rev. A
Issue 1
August 2002
Technisonic Industries Limited
240 Traders Boulevard, Mississauga, Ontario L4Z 1W7
Tel:(905)890-2113 Fax:(905)890-5338 www.til.ca
CAUTION
This unit contains static sensitive devices. Wear a grounded wrist strap and/or conductive gloves when handling printed circuit boards.
NOTE: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Warning:
Changes or modifications not expressly approved by Technisonic Industries could void the user’s authority to operate the equipment.
Important:
The TFM-550 transceiver is designed for airborne use. It is certified by Industry Canada under aeronautical standard RSS 141 as amended. The equipment is not permitted to be installed in a fixed or mobile, land based station in Canada.
WARRANTY INFORMATION
The Model TFM-550, Transceiver is under warranty for one year from date of purchase. Failed units caused by defective parts, or workmanship should be returned to:
Technisonic Industries Limited
240 Traders Boulevard
Mississauga,
Ontario L4Z 1P4
Tel: (905) 890-2113 Fax: (905) 890-5338
A Page
Summary of DO-160C Environmental Testing for Technisonic Model TFM-550, Low-band VHF, Highband VHF and UHF Transceiver:
Conditions
Temperature and Altitude
Vibration
Magnetic Effect
Power Input
Voltage Spike
RF Emission
Section
4.0
8.0
15.0
16.0
17.0
21.0
Description of Conducted Tests
Equipment tested to categories B2 and
D1.
Equipment is tested without shock mounts to categories B, M and N.
Equipment is class A.
Equipment tested to category B.
Equipment tested to category B.
Equipment tested to category Z.
Installation Approval Note
Presently no TSO standard exists for airborne FM transceivers. To make it easier for installation agencies to provide their customers with an approved installation supported by an effective
Airworthiness Approval, Technisonic has secured Supplemental Type Certificate (STC) Approvals (both
US and Canadian) on its Airborne FM products for many helicopters currently being delivered in the
US and Canada as well as a number of single engine fixed wing aircraft. The above referenced DO-
160C test data is also on file and available from Technisonic to support approval requirements in airframes for which Technisonic does not possess an STC.
Approved aircraft types are listed in the attachments to the formal STC documents. These STC's are the exclusive property of Technisonic and require the written authority of Technisonic for their use.
To assist Factory Authorized Technisonic Dealers in the certification process, we have placed copies of our Canadian and US STC's on our web site along with a letter of authorization for their use. These documents may be downloaded and used as support for the technical submission to FAA or Transport
Canada. Only factory authorized dealers/installers are permitted to download and make use of these documents on behalf of their customers (end users) in support of regulatory agency approval. Please refer to the Technisonic web site www.til.ca
for the latest issue of available STC’s and letter of authorization for use.
B page
Paragraph
SECTION 1
1.1
1.2
1.3
1.4
1.5
TABLE OF CONTENTS
Title Page
GENERAL DESCRIPTION
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Purpose of Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Model Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Technical Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
SECTION 2
2.9
2.10
2.11
2.13
2.14
2.15
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
SECTION 3
3.7.2
3.7.3
3.7.4
3.7.5
3.7.6
3.7.7
3.7.8
3.7.9
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.7.1
3.8
3.9
3.10
3.11
3.12
OPERATING INSTRUCTIONS
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Programming Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Priority and Selective Memory Channel Scanning . . . . . . . . . . . . . . . . . . . . . 2-4
Scanning Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Direct Frequency Entry Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Receive Frequency Simplex Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Keyboard Lockout Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Variable Frequency Mode Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
LED Display Variable Dimming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
90 Second Transmitter Time Out Feature . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Programming CTCSS Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Cross Band Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
PC Memory/Programming Download Capability . . . . . . . . . . . . . . . . . . . . . . . 2-7
INSTALLATION INSTRUCTIONS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Equipment Packing Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Transceiver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Installation Kit - Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Installation - Pin Locations and Connections . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Wiring Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Main Power +28VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Main Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
PTT (Ground Keying) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Front Panel Back Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Audio Outputs (600 and 4 Ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Audio Output Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Mic Signal Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Memory Up/Memory Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Internal Programming Enable/Disable Jumper . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Transmitter Power Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Transmitter Microphone Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Squelch Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Transmitter Deviation Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
SECTION 3
INSTALLATION INSTRUCTIONS - APPENDIX
Post Installation EMI Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 i
Table No.
3-1
LIST OF TABLES
Title Page
9-pin D and 15-Pin D Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
LIST OF ILLUSTRATIONS
Figure No.
2-1
2-2
3-1
3-2
3-3
3-4
3-5
3-6
3-7
Title Page
Operator's Switches and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
PC Up/Download Cable - Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Outline Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Internal Enable/Disable Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
External Adjustment Access Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
VHF Deviation Adjustment Potentiometer Location . . . . . . . . . . . . . . . . . . . 3-10
UHF Deviation Adjustment Potentiometer Location . . . . . . . . . . . . . . . . . . . 3-11
VHF LOW Deviation Adjustment Potentiometer Location . . . . . . . . . . . . . . . 3-12 ii
SECTION 1
GENERAL DESCRIPTION
1.1 INTRODUCTION
1.2
This publication provides operating and installation information on the TFM-550 Transceiver.
manufactured by Technisonic Industries Limited. The unit offers an extended frequency range with selectable channel spacing and is intended for use (in the U.S.) only by government agencies or contractors thereto, who have obtained licensing for operation in the 138-150 MHz portion of the VHF band. If the TFM-550 transceiver is used in CANADA, VHF operation is restricted to the following sub bands: 138-144, 148-148.99, 149.005-150.005 and 150.05-
174 MHz. Furthermore the TFM-550 is a frequency agile transceiver which is restricted to airborne use and must not be operated as a base station in Canada.
DESCRIPTION
1.3
1.4
The TFM-550, Transceiver is a frequency agile, fully synthesized airborne FM transceiver capable of operating in the 30 to 50 MHz, 138 to 174 MHz and 403 to 512 MHz frequency range in 2.5 kHz increments with either 25 kHz or 12.5 kHz channel spacing. The Transceiver can operate without restriction on any split frequency pair in either band.
The TFM-550 Transceiver provides 200 operator accessible memory positions per band, each of which is capable of storing a transmit frequency, receive frequency, transmit frequency
CTCSS tone or DPL code, receive frequency CTCSS tone or DPL code, an alphanumeric identifier for each channel and wideband (25 kHz) or narrowband (12.5 kHz) channel spacing assignment. Operating frequency and other related data are presented on a 96 character, four line LED matrix display. Data entry and function control are performed via a 12 button keypad.
Preset channels may also be scrolled and scanned (scanning only possible in VHF high and UHF bands) through keypad function activation. Data may also be entered via computer with the provided software and optional PC Up/download cable, P/N 993390-1.
PURPOSE OF EQUIPMENT
The TFM-550, VHF High/VHF Low/UHF Band FM Transceiver is designed to provide secondary airborne communications to facilitate operations which are typically performed in a low altitude environment. The transmitter sections of this unit have a minimum of 8 watts and do not exceed 10 watts output power, which may be reduced by a front panel switch to 1 watt, in order to reduce interference to land based systems.
MODEL VARIATION
There are four variations of the Model TFM-550 Transceiver. All units offer identical features and performance except for the following differences:
TFM-550, P/N 991095-1
TFM-550, P/N 991095-1 (5V)
TFM-550, P/N 991095-2
TFM-550, P/N 991095-2 (5V)
GREEN display and 28 Volt back lighting.
GREEN display and 5 Volt back lighting.
RED display and 28 Volt back lighting.
RED display and 5 Volt back lighting.
Both P/N's 991095-1 and 991095-2 are always provided with 28 Volt back lighting unless a specific request is made for 5 Volt AC operation.
1-1
1.5
TECHNICAL CHARACTERISTICS
Specification
GENERAL
Model Designation:
Frequency Range:
Tuning Increments:
Operating Mode:
Channel Spacing:
Physical Dimensions (including heatsink):
Weight:
Mounting:
Operating Temperature Range:
Power Requirement:
Voltage:
Current:
Frequency Selection:
CTCSS squelch/encoder:
DPL digital squelch/encoder:
DTMF encoder:
Audio Outputs:
Speaker Output:
Back Lighting:
Display Colour:
DPL is a trademark of Motorola Corporation
1-2
Characteristic
TFM-550
30 to 50, 138 to 174 and 403 to 512 MHz
2.5 kHz
F3E simplex or semi-duplex
25 or 12.5 kHz
Approx. 8.0" X 3.75" X 5.75"
Approx. 5.1 Lbs (2.3 Kg)
Panel Mount via Dzus fasteners
-45EC to +70EC
28.0 Vdc, ± 15%
Receive - 1.2 A Max.
1 Watt Transmit - 2.2 A Max.
8-10 Watt Transmit - 3.4 A Max.
8-10 Watt Dual Transmit
- 5 A Max.
200 memories per band programmed with: a) Tx Frequency/Rx Frequency b) Tx/Rx CTCSS tone or DPL code c) 9 character alpha numeric title
All CTCSS tones available
All standard DPL codes
All standard DTMF tones
0.5 Watts into 600 ohms
2.5 Watts min. into 4 ohms
28 Volts (standard) or
5 Volts (specify)
Green (standard) or
Red (specify)
1.5
TECHNICAL CHARACTERISTICS (continued)
VHF RECEIVER
Sensitivity at 12 dB SINAD
Adjacent Channel Selectivity
Spurious Attenuation
Third Order Intermodulation
Image Attenuation
FM Acceptance
Hum and Noise
Audio Distortion
Antenna Conducted Emission
UHF RECEIVER
Sensitivity at 12 dB SINAD
Adjacent Channel Selectivity
Spurious Attenuation
Third Order Intermodulation
Image Attenuation
FM Acceptance
Hum and Noise
Audio Distortion
Antenna Conducted Emission
VHF LOW RECEIVER
All specifications identical to VHF receiver
1-3
Better than 0.35 µV
-75 dB (25 kHz)
-70 dB (12.5 kHz)
-90 dB
-70 dB
-80 dB
± 6 kHz
Better than 45 dB less than 5% less than -70 dBm
Better than 0.35 µV
-70 dB (25 kHz)
-60 dB (12.5 kHz)
-80 dB
-70 dB
-60 dB
± 6 kHz
Better than 40 dB less than 5% less than -70 dBm
VHF, VHF LOW and UHF TRANSMITTER
RF Power Output
Output Impedance
Maximum Deviation
(In narrowband mode)
Spurious Attenuation
Frequency Stability
Microphone Circuit
Sidetone Output
Harmonic Attenuation
FM Hum And Noise
Audio Input
Audio Distortion
1 watt or 10 watts
50 ohms
±5 kHz (25 kHz mode)
±2.5 kHz(12.5kHz mode)
-90 dB below carrier level
± 2.5 ppm
Carbon or equivalent
0.5W (max) into 600S
-60 dB below carrier level
-40 dB
50 mV at 2.5 kHz into
200 S input circuit for
±3.5kHz deviation, adjst.
Less than 5%
1-4
2.1
SECTION 2
OPERATING INSTRUCTIONS
FEATURES
2.
3.
The equipment has several important operating features which provide maximum flexibility, performance and versatility. These features include:
1.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
The UHF band can be configured to be operated independently of the VHF High and
VHF Low bands or all three bands can operate as a single unit.
The unit can be set up as a cross band repeater, linking a VHF High and UHF frequency in both directions. The VHF Low band will not cross band repeat.
200 memory positions per band which can each be programmed with a transmit and receive frequency with 25 or 12.5 kHz channel spacing, Tx/Rx CTCSS tones or DPL codes and a 9-character alphanumeric title.
Scanning of preprogrammed memories with selective memory scanning, in up to 5 scan lists, for the VHF High or UHF band. The VHF Low band does not scan.
Priority scan of memory channel 1 in VHF high or UHF band. The Scan function can only be used for one of these bands at a time. Simultaneous scanning on both bands is not possible.
Direct frequency entry mode.
Receive frequency simplex function. (Repeater talk around)
Switchable RF output power between 1 watt and 8-10 watts.
Lockout of keyboard to prevent inadvertent entries.
Variable frequency mode to manually scan up and down in 1MHz, 100kHz or 2.5 kHz steps.
LED display variable dimming mode.
Selectable 90 second Tx time out feature.
PC Memory Upload or Download capability.
14.
Configuration Menu - Pressing ENTER, RCL and FUNC together while turning the radio on will put it into configuration mode. The programming features affected are: a) DPL - Can be turned on or off with the MUP and MDN
(4 and 7) keys. This only removes the DPL entry step from the programming sequence and does not stop memories that already have DPL codes from working. This also applies to the rest of the on/off configurable items.
b) Scan - Can be disabled. Selecting FUNC and SCAN will do nothing if Scan is off. The scan list indicator (+) will still display if was previously programmed.
c) Rx CTCSS - Can be turned on or off from the programming sequence. This affects only the
CTCSS tones for receive.
d) LAST MEM - If set to on, the last memory channel on the display will be what comes up when the radio is turned on. If set to off, the last memory that changes were made to will be what comes up when the unit is switched on.
e) DUALMODE - If set to ON, the UHF band is operated independently from the 2 VHF bands. (ie./ UHF audio separately available on 9pin connector). The radio is shipped with this feature OFF.
2-1
f) REMOTE BS - Only used when an RC-550 slave control head is attached. Setting this feature on will give the transmit selection to the Band Select switch on the RC-550 rather than on the radio.
This is useful when the operator at the RC-550 is using the VHF high and low bands. Regardless of whether this feature is set to on or off, the fourth squelch light will light on both units when both BS switches are set to the same position.
g) SIDETONE - The TX audio circuit becomes active allowing you to adjust the sidetone level with the VHF volume knob. When the desired level is reached, press ENTER and this level will be set for both VHF and UHF bands. The factory setting is 23.
Note: The sidetone level must be set every time you go through the configuration menu since it takes the setting of the volume knob regardless of whether you set it or not.
FIGURE 2-1 Operator's Switches and Controls
2-2
2.2
7.
8.
5.
6.
2.
3.
OPERATING INSTRUCTIONS (See Figure 2-1)
1.
Switch power on by turning the VHF volume clockwise. Depending how the radio is configured, either the last programmed or last displayed frequencies will appear on the screen. The transceiver is now in normal operating mode. NOTE: VHF high band will be
referred to as “VHF” and VHF low band as “VLO” in these instructions.
4.
Adjust the audio level by adjusting the VHF, UHF and VLO volume knobs.
Pressing the squelch defeat button will open all receivers to confirm they work.
Read the display. The top line will indicate which VHF memory is selected followed by a "+" if the memory position is included in a scan list, an alphanumeric message, and the frequency of the VHF receiver. A small "n" before the frequency indicates 12.5 kHz narrowband channel spacing is in effect on this memory position. In the receive mode, the frequency is followed by an "RT" if an RX CTCSS tone or RX DPL code is programmed, or an "RX" if no receive tone/code is programmed. Similarity, in the transmit mode either a
"TT" or "TX" is shown after the frequency. The second line shows the same information for the UHF band. The third line indicates the same information about the VHF LOW band.
9.
Set the VHF/UHF/VLO (BS) switch to the desired band.
The VHF/PRI switch is spring loaded and is normally in the VHF position. Pressing this switch down will result in channel 001 being loaded on the VHF band.
Set the HI/LO switch to the desired RF output power.
Select the desired memory by using the M.UP and M.DN buttons, or the RCL button and a three digit number followed by ENTER.
To transmit DTMF tones, use the keyboard keys while holding the PTT button on the microphone. There is a 5 second PTT delay after pressing a key so that you may press several DTMF keys in sequence without having to hold the PTT. The keyboard returns to its normal function when the PTT is released.
The display always shows the status of both receivers and the transmitter. The light at the left of each line indicates which receiver is receiving. The display also indicates the memory channel is in use. A "TX" (no TX tone/codes programmed) or "TT"(either TX tone or code programmed) on the right side of the display indicates which band is active when transmitting. The transmit frequency is also shown. In the receive mode the display shows “RX” beside the receive frequency if no RX tone or DPL code is programmed and “RT” if a CTCSS tone or DPL code is programmed.
While in any programming mode, all receivers continue to function. When the transceiver is in either of the operating frequency or CTCSS tone/DPL code programming modes and you must respond to a call, click the microphone PTT once (the radio will not transmit during this click). This will cause the transceiver to revert back to the normal operating mode and communications with the caller can proceed in the usual fashion. Pressing the FUNC key has the same effect.
2.3
PROGRAMMING INSTRUCTIONS
To program one of the 200 memory channels in one of the bands:
1.
Select the desired band on the band select (VHF/UHF/VLO) switch. This is required before any of the programming modes or functions.
2.
Press the FUNC key. The display will show the function prompt.
2-3
3.
4.
5.
6.
7.
8.
9.
10.
Press the PROG key. The display will show the current receive frequency with a flashing curser on the first or second digit (The first digit is always a one <1> on the VHF band and there is no hundreds digit on the VHF LOW band).
Type in the desired receive frequency. If you type in a frequency which is not a 2.5 kHz step, the nearest valid frequency will be automatically selected.
The curser will return to the second digit. You can retype the frequency if you have made an error or press ENTER to continue.
The transmit frequency will be displayed with the curser on the second digit. Follow the same method as in step 4 and 5.
The channel spacing increment of either 25.0 or 12.5 kHz is now displayed. Use the
M.UP and M.DN keys to select the desired channel spacing for the memory position, then press ENTER.
The alpha-numeric title is now displayed. Use the M.UP and M.DN keys to scroll through the alphabet, numbers and symbols. When the desired character is displayed, press
ENTER to advance to the next character. Press “1" to backspace.
Keep repeating step six until the last space is set (there are 9 characters). The display will show SCAN or LOCKOUT to enable this memory position as part of a scan list or lock it out of the scan lists. Use the 1,2,3,4,5 and M.DN keys to toggle between these functions
(for details see paragraph 2.5). Once the desired condition has been selected, press
ENTER. The TFM-550’s display will show a "+" beside the memory channel number if scan is enabled. Note: Scan function and Scan list feature not provided for VHF Low Band.
The display will now show the current memory number. Type in the 3-digit number of the memory you want to save to (if different from displayed one) and press ENTER.
2.4
PRIORITY SCANNING, SELECTIVE MEMORY CHANNEL SCANNING AND SCAN LISTS
Instead of breaking up the 200 channels into blocks for scanning, the TFM-550 has 5 scan lists per band (VHF high and UHF only). Any of the 200 channels can be assigned to any one or more of these 5 scan lists. This means the channels do not have to be repeated for them to be in more than one block and that you are not limited to the number of channels that can be scanned at once, since all 200 channels can be put into any scan list. Scanning is not available on the VHF Low band.
The priority memory channel is always memory position number 1. The priority memory channel is scanned every other step (ie. 121314151...) to ensure that no incoming messages are missed.
The priority channel can be locked out, which will result in the normal scanning of the other memory positions.
Selective memory scanning allows the user to select which of the 200 memory channels are to be scanned or locked out when the scan function is invoked. To use this feature, follow
PROGRAMMING INSTRUCTIONS found in paragraph 2.3. Once the screen displays SCAN or
LOCKOUT, use the 1,2,3,4,5 or M.DN keys to toggle to the desired condition and press ENTER.
Entering the any or all of the numbers 1,2,3,4 or 5 will include that memory channel in any of the five scan lists. In normal operating mode the display will later show a "+" beside the memory channel number if it has been included in any of the 5 scan lists.
2-4
2.5
2.6
2.7
2.8
SCANNING FUNCTION (5 second talkback delay)
Select the band you wish to scan with the band switch. (You can not scan VHF Low band).
To start scanning of the memory channels, press FUNC then SCAN and then the number (1,2,3,4,5) of the desired scan list.
The radio will scan through all the preset memory positions in the selected scan list (see above paragraph for priority and selective scan features) and will lock on to the first active channel in the scan sequence. It will remain on the channel until it becomes inactive. Scanning will resume again after five seconds of inactivity. To exit the scan mode, press the SCAN key. This will cause the radio to revert back to the normal operating mode.
If while scanning, you hear a call for you:
1.
Respond to the call within 5 seconds. When scanning is interrupted by an incoming signal, the channel will remain open for five seconds before resuming scanning.
2.
During communications the five second timer is reset from the last Rx or Tx signal encountered.
The radio resumes scanning once the Rx or Tx activity has ceased for more than five seconds.
The SCAN key must be pressed to exit the scan mode.
DIRECT FREQUENCY ENTRY MODE
This mode is designed to facilitate quick frequency selection during emergency and other operational conditions requiring direct operating frequency selection. This operating mode is disabled along with the programming mode when the internal disable jumper is set.
1.
2.
3.
When the transceiver is in the normal operating mode, press FUNC and the desired operating frequency ie/ 153.2750.
On the UHF band press FUNC and then 1 and the desired frequency ie/ 443.5500.
You will then be asked for 12.5 or 25.0 kHz channel spacing. Select with MUP or MDN and press ENTER.
Please note in the above operation, after FUNC and "1" are entered, the LED display will show memory channel "000" and then the remaining digits in the desired frequency are shown as they are entered. No alphanumeric message can be entered in this mode. Operation on the new frequency occurs in both transmit and receive (simplex only) modes. If RX or TX CTCSS tones/DPL codes are required they must be programmed in afterwards.
RECEIVE FREQUENCY SIMPLEX FUNCTION (Repeater Talkaround)
The receive frequency simplex function allows you to quickly change the transmit frequency, when operating on a split pair (repeater/semi-duplex mode), to the receive frequency to allow direct communications. ie/ If you are transmitting on 152.000 MHz and receiving 152.555 MHz, select
VHF on the band select switch and press FUNC then UP to transmit on 152.555 MHz. To return to the split pair condition, you must recall the memory channel again. This is quickly done by pressing
M.UP for one step up, then back down one step with the M.DN key.
KEYBOARD LOCKOUT FUNCTION
The keyboard can be locked out so that accidental pressing of keys does not change frequency, etc., unknowingly to the operator. To lock the keyboard, press FUNC then LOCK. This will disable all keyboard functions (except keyboard unlock) in the receive mode. The DTMF function during transmit will not be affected. To unlock the keyboard, press and hold the LOCK key for two seconds until the display indicates "UNLOCK".
2-5
2.9
VARIABLE FREQUENCY MODE FUNCTION
To enter variable frequency mode, press RCL, 0,0,0, then ENTER or enter a frequency in the direct entry mode described above. The memory channel that you were just in will still be valid but now you can manually adjust the frequency with the M.UP, M.DN, UP and DN keys. The UP and DN keys will make the frequency count up or down in steps of 2.5 kHz. The M.UP and M.DN keys will make the frequency count up or down in steps of 1 MHz. You can not change the label. The frequency in this mode can not be stored in memory. To exit this mode, recall one of the 200 memory channels (ie. RCL, 0,0,1). Variable frequency mode is disabled when the internal entry disable jumper is removed.
2.10
LED DISPLAY VARIABLE DIMMING MODE
1.
With the transceiver in normal operating mode press the UP or DN keys to increase or decrease the intensity of the LED display.
2.
Once maximum intensity of the display is achieved, the UP key no longer functions.
Conversely once minimum intensity is reached, the DN key ceases to function.
2.11
90 SECOND TRANSMITTER TIME OUT FEATURE
A selectable 90 second transmitter time out feature is provided to prevent accidental continuous transmission in the event of a faulty PTT switch. With this feature enabled the transceiver will stop transmitting after the PTT is engaged continuously for 90 seconds. The timer is reset by releasing then re-engaging the PTT switch.
Press the FUNC then the M.UP key. Use the M.UP and M.DN keys to select 90 SEC, which enables the feature, or NONE which disables it.
2.13
PROGRAMMING CTCSS TONES/DPL CODES
CTCSS tones (PL tones) or Digital DPL codes can be assigned to each memory channel on any
of the three operating bands. To program a tone/code to a memory channel:
1.
Select the desired band on the band select switch.
2.
3.
Use the M.UP and M.DN keys to select the memory channel that you want to assign a CTCSS tone or DPL code.
Press the FUNC key then the TONE key. The display will show "RX TONE:" and the current tone number, as well as the tone frequency in Hz.
4.
Use the M.UP and M.DN keys to select the tone number you require. The following is a list of the available CTCSS tones:
2-6
Number Tone
01 67.0
02 71.9
03 74.4
04 77.0
05 79.7
Number Tone
26 162.2
27 167.9
28 173.8
29 179.9
30 186.2
Number Tone
51 177.3*
52 183.5*
53 189.9*
54 196.6*
55 199.5*
06 82.5
07 85.4
08 88.5
09 91.5
10 94.8
11 97.4
12 100.0
13 103.5
14 107.2
15 110.9
31 192.8
32 203.5
33 33.0*
34 35.4*
35 36.6*
36 37.9*
37 39.6*
38 44.4*
39 47.5*
40 49.2*
56 206.5*
57 210.7*
58 218.1*
59 225.7*
60 229.1*
61 233.6*
62 241.8*
63 250.3*
64 No Tone
(carrier squelch only)
(The tones marked with * are
nonstandard tones).
16 114.8
17 118.8
18 123.0
19 127.3
20 131.8
41 51.2*
42 53.0*
43 54.9*
44 56.8*
45 58.8*
21 136.5
22 141.3
23 146.2
24 151.4
25 156.7
46 63.0*
47 69.4*
48 159.8*
49 165.5*
50 171.3*
Press ENTER. "TX TONE" appears on the display. Repeat step 3.
4.
5.
The display will now show "RX DPL:" and the current 3-digit DPL code. If no DPL code is required "000" should be entered. Please note that if a DPL code is to be programmed a CTCSS tone should not be enabled.
6.
Use the keypad to enter the required octal 3-digit DPL (Digital Coded Squelch or DCS) code. A list of all usable and unique octal 3-digit DPL/DCS codes follows:
7.
017* 051 116 156 243 266* 346 431 466 612 721
023 053* 122* 162 244 271 351 432 503 624 731
025 054 125 165 245 274* 356* 445 506 627 732
026 065 131 172 246* 306 364 446* 516 631 734
031 071 132 174 251 311 365 452* 523* 632 743
032 072 134 205 252* 315 371 454* 526* 654 754
036* 073 143 212* 255* 325* 411 455* 532 662
043 074 145* 223 261 331 412 462* 546 664
047 114 152 225* 263 332* 413 464 565 703
050* 115 155 226 265 343 423 465 606 712
* indicates GE Digital Coded Squelch (DCS) Code
Press ENTER. "TX DPL" appears on the display. Repeat step 6.
2-7
2.14
CROSS BAND REPEAT
The TFM-550 can act as a cross band repeater between VHF (high band only) and UHF. To enter repeat mode, press FUNC and then 9. The status line will show REPEAT instead of the band switch selection. When a signal is received on one of the bands, the audio is routed to the transmitter of the other band. This process can only go in one direction at a time. While transmitting, short bursts of noise due to intermittent signal strength or interference will be muted while the transmitter continues to transmit. There is also a short delay of silence (tail) after the received signal ends. The operator at the TFM-550 can monitor communications in both directions but can only talk to one band at a time via the band select switch. If the radio is set up in dual mode, the band selection is made at the audio panel. To cancel cross band repeat mode, press ENTER.
2.15
PC MEMORY PROGRAMMING UP/DOWNLOAD CAPABILITY
The TFM-500 transceiver can be programmed by a Windows based personal computer using
Technisonic software supplied on CD with each TFM-500.
Requirements:
1.
2.
3.
PC compatible computer with a CD ROM drive, running Windows 95/98/NT/2000/ME.
Bench power supply of 28 volts DC.
PC download cable, P/N 993390-1 which can be supplied or made from the wiring diagram at the back of this section.
Connections:
1. With the PC turned off, plug the 25 pin male 'D' connector into a serial port.
2.
3.
Plug the 9 pin 'D' connector into the back of the TFM-500 transceiver.
Connect the power supply to the TFM-500.
Installing the MultiTDP Program:
The CD supplied with each radio contains software for all of Technisonic’s downloadable transceivers. Place the CD into your drive and use Windows Explorer to open the MultiTDP directory on the CD. Double click the MultiTDP_Install.exe file. Follow the onscreen instructions to install the program onto your hard drive. When the program is installed, it can be run by selecting Programs from your Start menu, then select Technisonic from the submenu and finally MultiTDP.
Using the MultiTDP Program:
With the program running on your computer, a full MultiTDP instruction manual can be loaded by selecting Documentation in PDF format under the Help menu. Otherwise, to get started, pull down the File menu and select TFM-500. The program defaults to serial port com1 but can be set to com2, 3 or 4 under the Com Port menu. The program is now ready to use. You may want to upload data from the radio and edit channels or start a new data file. The VHF and
UHF bands are treated as separate radios and must be up or downloaded and edited separately. Editing is done on a channel by channel basis. Set the channel number you would like to edit and then modify the frequencies, labels, CTCSS tones, DPL codes, wide / narrow band setting and scan lists as desired. Press the Save Record button to store the changes youv’e made to the data base below. After you have edited the channel list your can save your
2-8
changes to disk and/or download to the radio. Only channels selected with a check mark will download. It is recommended to use the Select All command in the Data Transfer menu to ensure the data base in the radio matches the one in the PC. When download is selected, a message box will appear on your screen asking you to press FUNC and DN on the radio. Press these buttons on the radio before you click OK in the message box, otherwise the download will fail.
TFM-550 Upload/Download Programming Cable
P/N 993390-1 Wiring Diagram
Note: If your serial port is a 9 pin connector, instead of the 25 pin use a female
9 pin D connector, connecting:
Yellow -
Blue -
Black pin 3 pin 2 pin 5
FIGURE 2-2 TFM-550 Transceiver PC Up/Download Cable - wiring diagram
2-9
3.1
3.2
3.3
3.4
3.5
3.6
SECTION 3
INSTALLATION INSTRUCTIONS
GENERAL
This section contains information and instructions for the correct installation of the TFM-550,
VHF/FM Transceiver. Make certain that the correct frequencies are preprogrammed in accordance with the equipment user's valid FCC operator's license, prior to installation.
EQUIPMENT PACKING LOG
Unpack the equipment and check for any damage that may have occurred during transit. Save the original shipping container for returns due to damage or warranty claims. Check that each item on the packing slip has been shipped in the container. Verify that the equipment display and backlighting configuration are the same as those ordered.
TRANSCEIVER INSTALLATION
The TFM-550 transceiver is designed to be Dzus mounted and should be installed in conjunction with an IN-550 installation kit. See Figure 3-1 for an outline drawing of the unit with dimensions to facilitate the installation.
INSTALLATION KIT - CONTENTS
The IN-550 installation kit consists of:
1.
2.
3.
One 15 pin Cannon D mating connector (female) complete with crimp pins and hood.
One 9 pin Cannon D mating connector (male) complete with crimp pins and hood.
Three BNC antenna mating RF connectors (male).
ANTENNA INSTALLATION
Antenna, P/N’s ATM-150, ATM-403 and ATM-30 may be obtained from Technisonic Industries
Limited or suitable equivalent 0dB gain antennae may be utilized with the TFM-550 transceiver.
The antennae should be mounted on the bottom of the aircraft whenever possible and must be located at least 20 cm (8inches) from any occupant in the airframe. Consult with instructions provided with the antennas. Connect RF cables from antennas to the back of the
TFM-550 unit by utilizing the BNC mating connector provided in the installation kit. The VHF
Low band (top) and UHF (middle) BNC connectors are located on the rear, above the 15-pin
D connector and the VHF high band BNC connector is below the 9-pin D. If an external antenna tuner (ATU) is to be used, the ATC-550 (p/n 991102-1) will have to be utilized to control it. The ATC-550 is an external box to the TFM-550.
INSTALLATION - PIN LOCATIONS AND CONNECTIONS
The pin numbers and locations for the 15 pin and 9 pin Cannon D located on the rear of the
TFM-550 transceiver are shown below. Pin connections are in provided in TABLE 3-1.
Transceiver mounted view of 15 pin female and 9 pin male connector
2-10
FIGURE 3-1 Outline Drawing for Model TFM-550 Transceiver
3-1
10
11
12
13
14
15
6
7
8
9
Pin #
1
2
3
4
5
3.6
INSTALLATION - PIN LOCATIONS AND CONNECTIONS (continued)
15 Pin D Connections - Use FEMALE Connector
Description
600 Ohm Output 1
Data Output
Panel Lighting (28VDC or 5VAC)
Memory Up
Memory Down
Mic Signal Input 1
Main Power +28VDC
Main Ground
4 ohm Speaker Output
4 ohm/600 ohm Output Ground
Data Input
DF Audio
PTT 1 (Ground Keying)
Main Power +28VDC
Main Ground
Pin #
1
2
3
4
5
6
7
8
9
9 Pin D Connections - Use MALE Connector
Description
600 Ohm Output 2 (UHF Band in Dual Mode)
PTT 2 (Ground Keying)
Reset
Background Debug Signal
Ground
Programming Voltage In
Serial Data Out
Serial Data In
Mic Signal Input 2
TABLE 3-1
3-2
FIGURE 3-2 Wiring connections for the TFM-550 Transceiver
3-3
3.7
WIRING INSTRUCTIONS
Figure 3-2 shows all required connections and recommended wire sizes for the TFM-550
Transceiver.
If problems with the correct operation of the UHF/FM Transmit function of a TFM-550 are encountered on a specific airframe, a DC power line filter may be required. Typical problems encountered are that UHF/FM will not transmit on high power or will not open a repeater when using a CTCSS transmit tone. Investigation has determined that once the ripple on the airframes DC (28V) power line becomes excessive the UHF transmit function and tones will distort. If the airframes generators are turned off and the UHF/FM transmit function works correctly from 28 Vdc battery power, the ripple on the DC power line is excessive. The use of DC power line filter PLF-250, p/n 021214-1 is recommended and is available from
Technisonic.
3.7.1 Main Power +28VDC
The main power +28VDC (±15%) is connected to pins 7 and 14 of the transceiver. Both pins should be connected.
3.7.2 Main Ground
Ground connections for the transceiver are made on pins 8 and 15. Both pins should be connected.
3.7.3 PTT (Ground Keying)
The PTT line is connected to pin 13 and should be floating when the transceiver is in receive mode, and grounded during transmit mode. The PTT2 input is on pin 2 of the 9 pin connecter.
3.7.4 Front Panel Back Lighting
Front panel back lighting connection should be made on pin 3 of the transceiver. The opposite end of this lead should be connected to the panel lighting system of the aircraft. Before connecting, verify the required panel lighting voltage (28 VDC or 5VAC) on the transceiver configuration control label.
3.7.5 Audio Outputs (600 ohms and 4 0hms)
There are two audio outputs available (1 & 2). 600 ohm audio output 1 has audio from both
VHF bands and the UHF band in single operator mode. When in dual operator mode, 600 ohm output 1 has audio from the VHF High and Low bands only, while the UHF audio will be on the
600 ohm output 2. None of these outputs need to be terminated if left unused.
3.7.6 Audio Output Ground
Pin 10 is the ground for both the 4 ohm and 600 ohm audio output signals.
3.7.7 Mic Signal Input
The microphone input signal is to be provided on pin 6, utilizing shielded wire with the shield grounded to pin 10. Microphone signal 2 is on pin 6 of the 9-pin D connector.
3.7.8 Memory Up/Memory Down
Remote scrolling through the 200 memory positions can be achieved by providing a ground to pins 4 (up) and 5 (down) through a momentary contact cyclic switch. The memories will scroll only on the band selected.
3-4
3.7.9 Data Input
Data communications equipment requiring direct access to the modulator and discriminator an be connected via pins 2 and 11. Data cannot be transmitted in CANADA unless equipment is approved for use with the TFM-550 by the communications regulatory authority.
3.8
INTERNAL PROGRAMMING ENABLE/DISABLE JUMPER
1.
2.
3.
The programming and direct frequency entry modes can be disabled by removing the internal enable/disable jumper strap from pins 1 and 2 of J10. Removal of this jumper will prevent operation on any frequencies other than those programmed in the 600 memory positions. The transceiver is always shipped with the two jumpers in the entry enable positions. To place either of the jumpers in the disable position:
Remove the left side of the radio.
Set or remove jumpers as necessary.
Re-install the left side cover.
Microprocessor Control Unit (MCU) PCB Module:
FIGURE 3-3 Internal Enable/Disable Jumper Locations
(The Guard Entry Disable Jumper has no effect to the TFM-550)
3-5
3.9
TRANSMITTER POWER ADJUSTMENTS
1.
2.
The transmitter power is adjusted to a maximum of 10 watts in high power mode and 1 watt in low power mode over the transceiver operating bandwidth at the factory. If transmitter RF power re-adjustment is required, perform as follows:
Select the band that you wish to adjust on the band select switch.
Connect an RF through-line watt meter to the appropriate antenna connector. Set the operating frequency to 156.000 MHz for VHF or 457.000 MHz for UHF and key the transmitter.
3.
4.
5.
In low power mode, set the low power adjustment potentiometer on the left side of the chassis to produce 1.0 watt of RF output power (See Figure 3-3).
In high power mode, set high power adjustment potentiometer on the left side of the chassis to produce 9.5 watts of RF output power.
Verify that the RF output power is between 9 and 10 watts on 138.000 MHz and
174.000 MHz for VHF or 403.000 MHz and 512.000 MHz for UHF.
3.10
TRANSMITTER MICROPHONE LEVEL ADJUSTMENT
1.
2.
3.
4.
5.
Set the transceiver operating frequency to 156.000 MHz and connect an appropriate test receiver to the RF output connector. Ensure that the output of the transceiver is terminated into a proper dummy load.
Key the transmitter and input a -10 dBm (0.25 VRMS), 1 kHz audio signal into the microphone input.
Adjust the microphone level potentiometer (Mic Level 1) through the access hole located on the right side of the chassis (see Figure 3-4) to produce a 2.7 kHz deviation.
Verify that the deviation is at least 2.3 kHz on the following frequencies: 138.000
MHz, 162.000 MHz and 174.000 MHz.
For UHF, perform the same procedure using the Mic Level 2 pot on the left side of the transceiver and use the following frequencies: 403.000 MHz, 457.000 MHz and
512.000 MHz.
3-6
FIGURE 3-4 External Adjustment Access Holes
3-7
3.11
SQUELCH ADJUSTMENT
The squelch on all receivers is factory set to open at approximately 22 dB SINAD. This adjustment can be made or altered to suit local conditions as follows:
1.
2.
Set the receiver to 157.000 MHz for VHF, 457.000 MHz for UHF or 41 MHz for VHF
Low band..
Connect a signal generator to the antenna input of the desired band.
Set the signal generator to produce a ±3 kHz deviation with a 1 kHz tone on 157.000
MHz, 457.000
MHz or 41.000 MHz. Increase the signal generator RF level from 0.1 uV until the squelch indicator LED is on. Verify the squelch opens at the desired level.
3.
If not, re-adjust receiver squelch potentiometer through the access hole located on the bottom of the transceiver chassis (see Figure 3-4).
3.12
TRANSMITTER DEVIATION ADJUSTMENT
VHF:
1.
2.
3.
4.
5.
6.
UHF:
Remove the bottom cover of the transceiver.
Set the VHF operating frequency to 157.000 MHz and connect an appropriate test receiver to the RF output connector. Ensure that the output of the transceiver is terminated into a proper dummy load.
Key the transmitter and input a +10 dBm (2.5 VRMS), 2.5 kHz audio signal into microphone input 1.
Adjust the wide band deviation limit potentiometer, R30 on the VHF Rx/Tx module (see
Figure 3-5) to produce a ±4.20 kHz deviation. Select narrow band mode on the VHF band and adjust the narrowband deviation limit potentiometer, R76 on the VHF Rx/Tx module to produce a ±2.10 kHz deviation.
Verify that the deviation does not exceed ±5 kHz for wide band and ±2.5 kHz for narrowband on 138.000 MHz, and 174.000 MHz. Re-adjust R30 or R76 as required, if the deviation exceeds ±5 kHz or ±2.5 kHz, respectively.
Replace the bottom cover.
1.
2.
3.
4.
Remove the left side cover of the transceiver.
Select the UHF band.
Set the UHF operating frequency to 457.000 MHz and connect an appropriate test receiver to the RF output connector. Ensure that the output of the transceiver is terminated into a proper dummy load.
Key the transmitter and input a +10 dBm (2.5 VRMS), 2.5 kHz audio signal into microphone input 1 if in single mode or microphone input 2 if in dual mode.
3-8
5.
6.
7.
Adjust the wide band deviation limit potentiometer, R30 on the UHF Rx/Tx module (see
Figure 3-6) to produce a ±4.20 kHz deviation. Select narrow band mode on the UHF band and adjust the narrowband deviation limit potentiometer, R76 on the UHF Rx/Tx module to produce a ±2.10 kHz deviation.
Verify that the deviation does not exceed ±5 kHz for wide band and ±2.5 kHz for narrowband on 403.000 MHz, and 512.000 MHz. Re-adjust R30 or R76 as required, if the deviation exceeds ±5 kHz or ±2.5 kHz, respectively.
Replace the bottom cover.
VHF Receiver/Transmitter PCB Module
Notes: R30 is for 25 kHz (wide band) Deviation Adjustment
R76 is for 12.5 kHz (narrowband) Deviation Adjustment
FIGURE 3-5 Deviation Adjustment Potentiometer Location
3-9
UHF Receiver/Transmitter PCB Module
Notes: R11 is for 25 kHz (wide band) Deviation Adjustment
R102 is for 12.5 kHz (narrowband) Deviation Adjustment
FIGURE 3-6 Deviation Adjustment Potentiometer Location
3-10
VHF LOW Band Receiver/Transmitter PCB Module
Notes: R21 is for 25 kHz (wide band) Deviation Adjustment
R16 is for 12.5 kHz (narrowband) Deviation Adjustment
FIGURE 3-7 VHF LOW Deviation Adjustment Potentiometer Location
3-11
3.12 TRANSMITTER DEVIATION ADJUSTMENT - continued
VHF LOW:
1.
2.
3.
4.
5.
6.
Remove the top cover of the transceiver.
Set the VLO operating frequency to 41.000 MHz and connect an appropriate test receiver to the RF output connector. Ensure that the output of the transceiver is terminated into a proper dummy load.
Key the transmitter and input a +10 dBm (2.5 VRMS), 2.5 kHz audio signal into microphone input 1.
Adjust the wide band deviation limit potentiometer, R21 on the VLO Rx/Tx module (see
Figure 3-7) to produce a ±4.20 kHz deviation. Select narrow band mode on the VHF band and adjust the narrowband deviation limit potentiometer, R16 on the VHF Rx/Tx module to produce a ±2.10 kHz deviation.
Verify that the deviation does not exceed ±5 kHz for wide band and ±2.5 kHz for narrowband on 30.000 MHz, and 50.000 MHz. Re-adjust R21 or R16 as required, if the deviation exceeds ±5 kHz or ±2.5 kHz, respectively.
Replace the top cover.
3-12
APPENDIX TO INSTALLATION INSTRUCTIONS
POST INSTALLATION EMI TEST
PURPOSE
The purpose of this test is to identify any interference that the TFM-550 may cause with existing aircraft systems. As the TFM-550 installation may include the ATC-550 antenna tuner controller, this test, as required, will also identify any interference caused by the ATC-550.
TEST CONDITIONS
The TFM-550 transceiver and any accessories (e.g., RC-550, ATC-550) should be installed and function tested. The antenna VSWR should be checked. A forward/reverse power check with a inline wattmeter should show no more than 10% reflected power. For the following tests, insure that the power switch is in the high position.
METHODOLOGY
Most of the EMI tests can be accomplished on the ground. In some cases flight testing is required or is easier. If the aircraft is approved for IFR operations, then it is mandatory that interference between the TFM-550 Airborne FM and the approach aids be checked in flight.
The GPS should be operational and navigating with at least the minimum compliment of satellites.
The VHF comm should be set to the frequencies indicated with the squelch open. VOR/DME receivers should be set to the frequencies indicated and selected for display. If possible, set up a
DME ramp test set on the frequencies indicated and adjust the output until the flags are out of view.
The transponder and encoder should be monitored with ramp test equipment. Set the output of the transponder test set to 3db above the output necessary to achieve 90% reply. If possible set the ADF to a nearby navigation station.
Modulate the TFM-550 transmitter on the indicated frequencies for at least 20 seconds.
Observe the GPS for any degradation in satellite status or availability or flags. Listen for any noise or detected audio signals on the VHF comm(s). Listen for any noise or detected audio signals on the
VOR/LOC receiver audio; look for any moment of flags or needles on the VOR/LOC/GS navigation display(s). Observe the transponder for any loss of reply or spurious reply.
List the power plant, fuel and other electric instruments in the chart provided and note any anomalies that occur while transmitting. Assess the results.
If the aircraft is equipped with an autopilot or a stability augmentation system, then test fly the aircraft and verify that operation of the TFM-550 transceiver does not have adverse effects on these systems. After checking for gross effects at a safe altitude, fly an approach with each of the different navigation systems coupled to the autopilot (ILS, GPS ETC.) and look for any anomalies.
When the installation includes the ATC-550 antenna tuner controller, this test, where indicated by an asterisk (*), will also identify any interference caused by the ATC-550. In these cases the ATC-
550 must be turned on and off by means of its breaker as often as required while monitoring the victim equipment.
A-1
RESULTS
If the installed system passes all of the applicable EMI tests, then no further action is required. If interference is observed then the interference must be assessed against the appropriate standards of airworthiness for the system in question. For example it is permissible for a VFR certified GPS to lose navigation capability while the TFM-550 unit is transmitting, providing that it recovers properly and promptly, but it is not permissible for an IFR Approach certified GPS to be affected in the same way. A complete discussion of all the standards of airworthiness to be applied in assessing EMI effects is beyond the scope of this document.
PROCEDURE
A.
Operate the TFM-550 transmitter on the following frequency for at least 20 seconds.
Observe the GPS for any degradation in satellite status or availability or flags.
PASS
GPS #1
FAIL PASS
GPS #2
FAIL
NOTES:
FREQUENCIES
TFM-550
39.3855 MHZ
143.180 MHZ
143.1825 MHZ
157.5000 MHZ
157.5425 MHZ
512 MHZ
A-2
B.
Determine if the image frequency for the VHF Comm falls within the range of the TFM-550.
If so, select a set of frequencies that will cause the TFM-550 to be set as close as possible to the image frequency. Any one of the many possible sets will suffice. Record those values in the spaces provided in the following chart. Modulate the TFM-550 transmitter on the following frequencies for at least 20 seconds. Listen for any noise or detected audio signals on the VHF comm.
Example - Bendix/King KY 196A:
The first IF frequency is 11.4 MHZ. The L.O. is above the received frequency (high side injection), therefore the image frequency is 22.8 MHZ above the selected frequency. Set the
KY 196A to 120.000 MHZ and the TFM-550 to 142.8000 MHZ.
(Note: Where indicated by an asterisk (*), required action is to switch ATC-550 on and off as often as necessary.)
118
118
135.975
121.15
VHF #1
FREQUENCIES
TFM-550
34
45
138
157.5
157.5
131.25
128
Image:
*
RESULTS
PASS FAIL
118
118
135.975
121.15
VHF #2
FREQUENCIES
TFM-550
34
45
138
157.5
157.5
131.25
128
Image:
*
RESULTS
PASS FAIL
NOTES:
A-3
C.
Determine if the image frequency for the VOR/ILS Nav falls within the range of the TFM-
550. If so, select two sets of frequencies that will cause the TFM-550 to be set as close as possible to the image frequency. Choose one set in the localizer frequency range and one in the VOR frequency range. Record those values in the spaces provided in the following chart.
Modulate the TFM-550 transmitter on the following frequencies for at least 20 seconds.
Listen for any noise or detected audio signals on the receiver audio; look for any moment of flags or needles on the navigation display.
(Note: Where indicated by an asterisk (*), required action is to switch ATC-550 on and off as often as necessary.)
108
108
FREQUENCIES
VOR/ILS #1 TFM-550
36
162
108.1
108.1
36.0333
162.15
112
Image:
*
RESULTS
PASS FAIL
NOTES:
108
108
108.1
108.1
112
Image:
FREQUENCIES
VOR/ILS #1 TFM-550
36
162
36.0333
162.15
*
RESULTS
PASS FAIL
A-4
D.
Modulate the TFM-550 transmitter on the following frequencies for at least 20 seconds.
Observe the Glideslope displays. Look for any movement of flags or needles on the navigation display.
G/S #1
334.7 (108.1)
FREQUENCIES
TFM-550
33.47
334.7 (108.1) 167.35
RESULTS
PASS FAIL
G/S #2
334.7 (108.1)
334.7 (108.1)
FREQUENCIES
33.47
167.35
TFM-550
RESULTS
PASS FAIL
NOTES:
A-5
E.
Operate the TFM-550 transmitter on the following frequency for at least 20 seconds.
Observe the Transponder for any spurious replies or loss of reply to test set.
NOTES:
FREQUENCIES TRANSPONDER #1 TRANSPONDER #2
TFM-550 PASS FAIL PASS FAIL
515 MHZ
A-6
F.
Modulate the TFM-550 transmitter on the following frequencies for at least 20 seconds.
Observe the DME displays. Look for loss of distance information on the display.
DME 1
978 (108.0)
1020 (112.1)
FREQUENCIES
TFM-550
489
510
RESULTS
PASS FAIL
NOTES:
DME 2
978 (108.0)
FREQUENCIES
TFM-550
489
1020 (112.1) 510
RESULTS
PASS FAIL
A-7
* G.
While turning the ATC-550 on and off as often as required, listen for any noise or detected audio signals on the HF receiver audio
FREQUENCIES
HF #1
16 MHZ
RESULTS
PASS FAIL
FREQUENCIES
HF #2
16 MHZ
RESULTS
PASS FAIL
NOTES:
A-8
NOTE:
For the following tests, select a frequency at the top, middle and bottom of each band of the TFM-
550 transceiver.
30 to 50 MHZ
Band
138 to 174 MHZ
Band
403 to 512 MHZ
Band
Frequency #1
Frequency #2
Frequency #3
H.
At a safe altitude engage the autopilot or stability augmentation system. Modulate the TFM-
550 transmitter on the above frequencies for at least 20 seconds. Observe any effect on the autopilot or stability augmentation system.
Observations:
I.
Perform a coupled ILS approach to the aircraft's certified limits. Modulate the TFM-550 transmitter on the above frequencies for at least 20 seconds. Observe any effect on the autopilot. Repeat for second flight director/autopilot if equipped.
Observations:
A-9
J.
List the power plant, fuel and other electric instruments in the chart provided and note any anomalies that occur while transmitting or switching ATC-550 antenna tuner controller on and off. Assess the results.
PASS FAIL NOTES
5
6
7
STEP
1
2
3
SYSTEM
Com 1&2
(High Band)
Transponder & Encoder
(Low Band and Mid Band)
ADF 1 & 2
4 VG
Glideslope 1&2
(High Band)
VOR/LOC 1&2
(High Band)
Compass
A-10
STEP
8 Directional Gyro
SYSTEM
11
12
13
9
10
14
15
Fuel Pressure
Oil Temp
Amps
Bus Voltage
Fuel %
Ng
TOT
PASS FAIL NOTES
A-11
STEP
16 Torque %
SYSTEM
19
20
17
18
Annunciators
Digital Clock
Oil Pressure
DME 1&2
(Low Band and Mid Band)
PASS FAIL NOTES
A-12
STEP SYSTEM PASS FAIL NOTES
NOTES:
A-13

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- VHF, VHF LOW and UHF Band Operation
- 200 memory positions
- Frequency agile
- Selectable 25 kHz or 12.5 kHz channel spacing
- CTCSS tone / DPL code programming
- Scan function
- Direct frequency entry
- PC Memory Programming