Unitech PA600 User manual
Unitech PA600 is a PDA Barcode Scanner that combines the latest technology with user-friendly features to bring you a powerful and versatile data collection tool. With its fast and accurate scanning capabilities, the PA600 is perfect for a wide range of applications, including inventory management, asset tracking, and point-of-sale transactions. Its compact and lightweight design makes it easy to carry and use, while its long battery life ensures that you can power through even the most demanding tasks without interruption.
Advertisement
Advertisement
unitech
PA600 PDA Barcode Scanner
User’s Manual
Preface
About This Manual
This manual explains how to install, operate and maintain the PA600 PDA Barcode
Scanner.
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from the manufacturer. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.
© Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved.
Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, Windows and Active-
Sync are either registered trademarks or trademarks of Microsoft Corporation. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Regulatory Compliance Statements
FCC Statement
This is a FCC Part 15 Class B product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
Canadian Compliance Statement
This Class B Digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.
The device is certified to the requirements of RSS-139-1 for 2.4 GHz spread spectrum devices.
European Conformity Statement
Declaration of Conformity with Regard to the R&TTE 1999/5/EC and EMC 89/336/
EEC directives.
i
ii
Laser Information
The Unitech PA600 series is certified in the U.S. to conform to the requirements of
DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and
Class 2 products are not considered to be hazardous. The PA600 series contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or during prescribed service operations.
The laser safety warning label required by the DHHS/IEC for the PA600 series's optional laser scanner module is located on the memory compartment cover, on the back of the unit.
CAUTION!
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes, and magnifying glasses.
This does not include eye glasses worn by the user.
Notices
This unit is equipped with a battery pack and backup battery. It is possible that the
Unitech PA600 may not power-on due to battery discharge as a result of storage.
In the above situation, plug the PA600 to the USB charging cable which is with DC in port or put the unit into the Unitech PA600 Cradle (with 5V/2A AC-DC adapter), and recharge the unit for 16 hours in order to fully charge its backup battery.
The backup battery will charge from external power or the main battery (if the main battery still has enough power to turn on). In the event the main battery is fully charged, refrain from using the PA600 for 16 hours in order for the main battery to fully charge the backup battery.
Backing-up data by backup battery only without the main battery installed in battery compartment may take as long as 6 hours. Therefore, in order to prevent data protection failure due to backup battery failure, do not leave the PA962 without the rechargeable battery pack installed, or without connection to AC power for an extended period of time.
Battery charge notice
It is important to consider the environment temperature whenever you are charging the Lithium-Ion battery pack. The process is most efficient at normal room temperature or slightly cooler. It is essential that you charge batteries within the stated range of -5°C to 50°C. Charging batteries outside of the specified range could damage the batteries and shorten their charging life cycle.
About This Manual
Storage and safety notice
Although charged Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at temperatures between-20°C to 60°C, however they may be depleted more rapidly at the high end of this range. It is recommended to store batteries within normal room temperature ranges.
iii
iv
Table of Contents
i
Regulatory Compliance Statements
............................................................................. i
................................................................................................................. ii
...................................................................................................................................... ii
1
....................................................................................................... 1
................................................................................................................................... 2
............................................................................................................... 3
Front Left View........................................................................................................................ 4
Back View ............................................................................................................................... 6
...................................................................................................................... 8
16
................................................................................... 16
Adjusting the Screen Brightness
................................................................................ 18
................................................................................................................. 18
................................................................................ 19
................................................................................................ 20 v
vi
22
Establishing Device-PC Connection
.......................................................................... 22
Synchronizing with Your Computer
........................................................................... 27
............................................................................................ 33
Using ActiveSync to Exchange Files
........................................................................ 33
35
.............................................................................................................................. 35
.................................................................................................................. 35
37
............................................................................................................. 37
Checking the Main and Backup Battery Status
..................................................... 38
..................................................................................................... 39
......................................................................................... 41
........................................................................................ 42
45
Chapter 1
Getting Started
Introducing the PA600
Thank you for purchasing the PA600 PDA Barcode Scanner.
Your PA600 was designed for user who need a compact and durable PDA for data collection and real time transactions.
The PA600 is a rugged, compact and lightweight palm-size computer using the Windows Mobile 5.0 operating system, and incorporating an integral bar code scanning laser device, color LCD with touchscreen, keypad, IrDA interface, and wireless communication capability. It provides users with a standard Windowsbased environment for customizing and operating the device.
To reduce TCO, the PA600 is sealed to meet IP54 standards and has undergone multiple drop tests to prevent downtime.
1
Features
Powerful system
• Microsoft Windows Mobile 5.0 /
Windows CE NET 5.0 operating system
• Intel PXA270 processor with speed of up to 520 MHz
System memory
• 64 MB SDRAM
• 128 MB Flash ROM
Display
• 3.5-inch QVGA LCD touch-sensitive screen
• 320 x 240 resolution
Barcode scanner
• Built-in Bar Code Scan Engine
• Built-in vibrator for scanning indication
• CCD scan engine (optional)
• Symbol SE950 support
• UNITECH HAMSTER barcode decoder
Communication
• USB Host & Client
• IrDA 1.2 (SIR)
• GPRS (Data Only)
• VOIP support
• 802.11b/g for power saving
• Bluetooth version 1.2
(supports Bluetooth Printer,
Bluetooth Modem, Bluetooth
ActiveSync)
Audio
• Voice recording and playback
• MIC
• Speaker
• Headset Connector
• Receiver
Wireless connectivity
• 802.11b + g with diversity antenna
• Bluetooth wireless technology
• Serial infrared port
Expansion slot
SDIO slot
Battery life
• Normal usage: 6 hours
• Charging time: 3.5 hours
• Embedded backup battery cell
User-friendly interface
• Quick launch hot keys for enabling backlight, calibration, software keyboard, and other device management tasks
• Trigger keys for barcode scanning
2
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 1 Getting Started
Package Contents
After opening the box, ensure the following accessories for the PA600 are present:
PA600 Terminal
Battery Pack Stylus
AC Adapter
USB Charging
Cables
Elastic Stylus String CD-ROM
Quick
Reference
Guide
If anything is missing or appear damaged in any way, contact your dealer.
3
A Tour of the PA600
The following sections describe the main components and features of the PA600.
Front Left View
No.
1.
Component
Status indicator
Description
Indicates the battery charging and barcode scanning status.
Green - Battery is fully charged, the device is running on battery power, or barcode scanning process is completed without error.
Red - Battery is charging, barcode scanner is activated and processing.
Press to activate the barcode laser scanner. 2.
Left scanner trigger button
3.
Power button If the device is off, press this button to turn it on.
Alternatively, when the unit is on, this key must be pressed and held down for about two seconds in order to turn the device off.
Enables you to record voice audio.
4.
Microphone
5.
Universal connector
Connects your device to a USB charging cable, which in turn connects to the computer’s USB port and through the AC adapter to an electrical outlet.
This allows you to recharge your device and perform an ActiveSync operation.
You can also use it to connect a peripheral hardware, such as an docking station, to your device.
6.
Keypad
Keypad interface for controlling the PA600. See Keypads
and Function Buttons on page 14 for more information.
7.
LCD Touch screen Displays the applications and data stored on your device. It is touch-sensitive and responds to the stylus or finger.
8.
Speaker Enables you to hear audio from the PA600.
4
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Back View
Chapter 1 Getting Started
No.
9.
Component
Battery compartment
Description
Houses the Removable and rechargeable 3.7
V, 1920 mAH battery pack
Opens the battery compartment.
10.
Battery compartment release latch
11.
Reset button
12.
18.
Handstrap
Stylus
Press the end of the stylus into the button to reset your device.
Enables you to securely hold the PA600 while using it.
Enables you to hear audio from the PA600.
13.
Speaker
14.
Strap holder
15.
Memory card slot Accommodates Secure Digital memory cards.
16.
Barcode scanner window Used to scan barcodes.
17.
Earphone jack
Attachment location for holding hand strap, carrying strap, and stylus.
Connects to audio line-out devices (earphones or headphones) for use in noisy environments.
Enables you to interact with the operating system.
To use the stylus, remove it from its holder and hold it the same way you hold a pen or pencil.
Press to activate the barcode laser scanner. 19.
Right scanner trigger button
20.
Infrared (IR) port Uses infrared technology to transmit and receive data from other IR-enabled devices.
5
Getting Started
This section explains how to install and charge the battery, how to check battery status, how to turn on the PA600, and how to calibrate the screen.
Installing the Battery
WARNING!
There is a risk of fire and burns if the battery pack is handled improperly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guidelines in your area.
A backup battery cell is embedded into your device to prevent data loss in instances when the removable battery pack is removed or completely discharged. This backup battery cell will only support the system for a maximum of 60 minutes.
NOTE:
To enable the internal battery cell to provide backup power supply, charge your device with the main battery pack for at least 12 hours.
1. Open the battery compartment by pushing the latch in the direction of the arrow and lifting up.
The battery compartment is displayed:
Compartment contacts
Plastic battery tab
Battery securing clip
NOTE:
The plastic battery tab makes it easy to remove the battery.
6
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 1 Getting Started
2. Position the battery pack, making sure the battery contacts are aligned with the contacts in the compartment and the battery is placed on top of the plastic tab, as shown in the following illustration.
Contacts
Plastic tab
3. Slide the battery pack into the battery bay while simultaneously pulling the plastic tab and securing clip until the battery clicks into place.
Securing clip
Plastic tab
4. Replace the battery compartment cover.
7
Charging the Battery
Before using the PA600 for the first time, you need to charge it for about 16 hours.
After that, you can charge the PA600 every day to recharge the battery to full capacity.
Charge the PA600 using the USB charging cable or the docking station.
CAUTION!
Operating the PA600 for the first time without the AC adapter, and without fully charging the backup battery may result in loss of data stored in RAM memory.
NOTE:
Data you enter may not be properly stored until the built-in backup battery has been adequately charged.
Charging the Battery using the USB Cable
1. Press and hold the connector button on the USB charging cable and connect it to the PA600 (1).
2. Plug the AC adapter cable into the power jack on the USB charging cable (2).
3. Connect the AC adapter into an electrical outlet (3).
8
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 1 Getting Started
Charging the Battery with the Docking Station
1. Plug the AC adapter cable into the power jack on the docking station, then connect the AC adapter into an electrical outlet.
2. Slide the device into the docking station until it clicks into place.
3. The connection is secure when the bottom edge of the device is aligned with the docking station, and the LED indicator on the device lights up red.
LED Status
PA600
Docking
Station
LED
Solid Red
Solid Green
Power LED
Meaning
Charging
Charging complete
Power is on
Charging LED: Charging
Sync LED Synchronization is taking place
Checking the Battery Status
If the battery level becomes low in the course of normal use, a status icon appears on the device screen indicating low or very low battery status. In both cases, perform an Active-
Sync operation to back up your data, then recharge your device as soon as possible.
If the battery level reaches low status, the device will enter sleep mode; if the battery level reaches very low status, the device will enter deep sleep mode. In this case, you have about 72 hours to recharge your device after which you risk losing all data on your device’s internal memory.
9
Connecting the PA600 to a PC
Use the USB cable to connect the PA600 to a PC to use with ActiveSync.
1. Press and hold the connector button on the USB charging cable and connect it to the PA600 (1).
2. Plug the USB connector into the USB port on the PC and connect the AC adapter into the USB connector (2).
3. Connect the AC adapter into an electrical outlet (3).
10
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 1 Getting Started
Turning the PA600 on for the First Time
After you have initially charged your device for about 12 hours, the device is ready to be used. You can now start up your device where you’ll calibrate the display, learn some basic stylus usage, and set up the system time zone, date and time.
Powering On
1. Turn on your device by pressing the power button on the front panel.
NOTE:
The PA600 screen ships with a protective plastic film.
You may remove this if desired by peeling from one corner. The screen will be more susceptible to scratching without the film, but will be more readable.
2. The Unitech PA600 welcome screen appears for a moment followed by the Windows CE screen.
Power Button
11
Calibrating the PA600 Screen
The calibrate screen automatically appears when the unit is powered-on for the first time or after the system is reset.
To calibrate the screen at any time, follow these instructions.
1. Tap Start
→ Settings, and then click the System tab.
2. Tap the Screen icon.
12
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 1 Getting Started
The Screen Settings window appears.
This window enables you to customize the screen settings.
3. Tap Align Screen to calibrate the screen.
The align screen window appears.
4. Tap the cross hair firmly and accurately.
The cross hair moves to the next location.
5. Continue tapping the cross hairs until the screen has been calibrated.
13
Chapter 2
Using the Hardware
Keypads and Function Buttons
The keypad enables you to both enter information and interact with the PDA operating system and also operate secondary functions using the function button. When the green function button is pressed, the green icon functions on the keypad become available.
When the Function button is pressed, an icon appears in the operating system:
Function activated icon
The following table describes the keypad keys.
Key Main Function
Turns the PA600 on and off.
Secondary Function
—
Number 1
Left soft key - activates function above in LCD screen.
Alphanumeric 2, a, b, c
Alphanumeric 3, d, e, f
Up navigation key
Right soft key - activates function above in LCD screen.
14
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Key Main Function
Enter key
Back space
Alphanumeric 4, g, h, i
Alphanumeric 5, j, k, l
Alphanumeric 6, m, n, o
—
Tab
Alphanumeric 7, p, q, r, s
Alphanumeric 8, t, u, v
Alphanumeric 9, w, x, y, z
Alpha
Asterisk
Number 0, space
Period
Chapter 2 Using the Hardware
Secondary Function
OK
Escape key
Left navigation key
—
Right navigation key
Enables disables secondary function keys
Windows key opens Start menu
Decreases screen brightness
Down navigation key
Increases screen brightness
—
Illuminates keypad
—
Pound
15
Adjusting the Screen Brightness
Adjust the screen brightness by pressing the Function button to enable the soft keys and pressing the 7 (decrease brightness) or 9 (increase brightness) buttons.
Increase
Brightness
Decrease
Brightness
Function Button
Using the Stylus
CAUTION!
Never use anything other than the PA600 stylus on the screen. Using another object as a stylus could cause permanent damage.
1. Remove the stylus from its holder.
2. Hold the stylus as you would a pencil.
3. To make a choice from a menu, lightly tap the tip of the stylus on that choice.
4. To write data into a field on a form, use the stylus to print the letters or numbers.
Use very light pressure.
16
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 2 Using the Hardware
Using the SD/MMC memory card
Your device has an expansion slot compatible with a range of SD and MMC storage cards, which are primarily used to back up or transfer files and data. The slot also supports SDIO cards for added connectivity options.
Inserting a Storage Card
1. Remove the two screws from the SD compartment cover and remove the cover.
2. Insert the SD card with the notched corner as shown by the icon on the case.
3. Push the card into the slot until you hear an audible system sound; this will signal that the card is already properly seated within the slot.
The card is secure when it is not protruding from the slot.
Removing a Storage Card
1. Remove the two screws from the SD compartment cover and remove the cover.
2. Press the card in and release.
The card pops out. An audible system sound will signal that the card has been released.
3. Remove the card from the slot.
17
Using the Laser Scanner
The PA600 has an integrated laser scanner which reads all major bar code labels with excellent performance.
NOTE:
Reading software must be enabled in order to operate the scanner. This can be a user-loaded application or a pre-loaded utility such as Scanner
Setting.
Activate the laser scanner by pressing either one of the trigger keys located on the left and right side of the unit.
The PA600 has a built-in Scanner Setting utility that allows you to test the device’s barcode scan function.
Scan button
1. To launch Scanner Settings, tap Start
→
Settings
→ System → Scanner Settings.
2. The Scanner Control Panel opens.
From here you can configure barcode scanner parameters such as enabling or disabling barcode symbologies, setting data transmission options, configuring magnetic and proximity reading options, and setting power management options.
18
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
3. To test the barcode scanner, tap the Test tab and press one of the scanner buttons on a barcode. The screen will display the results of the scan.
Chapter 2 Using the Hardware
19
Chapter 3
Getting Connected
Establishing Device-PC Connection
Installing Microsoft ActiveSync
In order to exchange data between your computer and PA600, Microsoft ActiveSync must be installed on your computer. Use the USB charging cable that comes with your device to connect the device to your computer.
NOTE:
If you have a previous version of the Microsoft ActiveSync installed in your computer, uninstall it first before installing the latest version of
Microsoft ActiveSync.
To install Microsoft ActiveSync on your computer:
1. Close any open programs, including those that run at startup, and disable any virus-scanning software.
2. Download the ActiveSync software from the Microsoft ActiveSync Download page at
http://www.microsoft.com/windowsmobile/ downloads/activesync42.mspx.
3. Browse to the location of the downloaded file, and double-click it.
The installation wizard begins.
20
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 3 Getting Connected
4. Click Next.
You are prompted to read the End User License Agreement (EULA).
5. Accept the license agreement terms and click Next.
You are prompted for user information.
6. Type the user name and organization and click Next.
You are prompted for the destination folder.
21
7. Select a drive to install the program to and click Next.
The installation wizard has gathered the information it needs to install Active-
Sync and prompts you to begin installation.
8. Click Install.
The program begins installation
After the program has finished installing you see the following screen.
22
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 3 Getting Connected
9. Click Finish.
You may be prompted to restart your computer.
After you have installed ActiveSync and restarted your computer, the ActiveSync icon
appears in your computer’s system tray as shown and ActiveSync Connection
Wizard starts. For detailed information on how to use ActiveSync on your computer, start ActiveSync then click Help
→ Microsoft ActiveSync Help.
Connecting the Device to Your Computer
1. After ActiveSync has been installed, connect the USB charging cable to the universal connector on the bottom of your device. If necessary, connect an
adapter. Refer to Connecting the PA600 to a PC on page 10.
2. Plug the other end of the USB charging cable into a USB port on your computer.
3. Turn the device on.
4. ActiveSync starts automatically and configure the USB port to work with the
PA600. The New Partnership setup wizard will automatically start.
NOTE:
If ActiveSync doesn’t start automatically, click Start
→ Programs →
Microsoft ActiveSync.
If a message appears indicating that it is unable to detect a connection, click the Cancel button and manually configure the communication settings.
5. Follow the onscreen instructions.
6. When the configuration process is complete, the
ActiveSync window appears.
7. Synchronization will be initialized and will take place if you’ve chosen to synchronize periodically or upon connection.
NOTE:
Your computer can create a partnership with multiple PA600s. Also, a
PA600 can create a partnership with up to two computers.
23
Synchronizing with Your Computer
Synchronization takes place according to the options you choose while setting up
ActiveSync on your computer. If you accept the default (On Connect) synchronization option in the Microsoft ActiveSync Setup Wizard, you’ll be able to simply connect your
PA600 to your desktop computer and synchronization will take place.
If you have not enabled the On Connect feature in Active Sync, you can start Active-
Sync in either of the following ways:
• On your computer, double-click My Computer
→ Mobile Devices folder.
• Connect the USB cable between the computer and PA600.
• Execute “Rellpog.exe” from the PA600 Windows directory
Connection options
You can set remote synchronization with your computer using the following connection options:
• USB connection
• Infrared connection
• Bluetooth connection
• WiFi connection
USB Connection
To synchronize with your computer using a USB connection:
1. Open ActiveSync.
2. Connect your device to your computer using the USB charging cable.
3. Initiate connection by tapping Start
→
Programs
→ ActiveSync.
4. Tap Menu
→ Connections.
5. Select Synchronize all PCs using this connection check box.
6. Select a baud rate or cable type connection.
7. Tap OK.
24
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 3 Getting Connected
Infrared Connection
The infrared port allows you to synchronize information with an infrared enabled computer. Align the infrared port of your device with the infrared port on the computer.
This method is ideal for quickly switching between multiple devices since there are no cables or adapters to change.
1. Perform the steps below on your computer: a. Configure an infrared port on your computer following the manufacturer’s instructions.
b. Once your computer’s IR port is ready, open ActiveSync.
c. Click File
→
Connection Settings.
d. Check Allow connec-
tions to one of the fol-
lowing and select
Infrared Port (IR) from the drop-down list.
e. Click OK.
25
2. Perform the steps below on your device: a. Align the IR port of your PA600 with that on your computer so that they are unobstructed and within close range.
b. Initiate connection by tapping Start
→
ActiveSync
→ Menu → Connect via
IR.
c. Tap Sync.
Bluetooth Connection
Your device is equipped with Bluetooth wireless technology that you can use to synchronize information with a computer equipped with a Bluetooth adapter or access point. Bluetooth wireless technology allows you to communicate with the computer whenever it is within range.
Follow these instructions to set up a Bluetooth connection.
1. Tap Start
→ Settings → Connections →
Bluetooth
→ Mode and check Turn on
Bluetooth.
26
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
2. Tap Devices
→ New Partnership…
Chapter 3 Getting Connected
3. Select a device from the list and tap Next.
You are prompted for a passkey.
4. Enter the Passkey.
27
On the PC screen, you are prompted to enter the Bluetooth PIN
Code Request.
5. Enter the same Bluetooth PIN Code you entered in step 4.
6. On the PA600 tap Partnership Settings
→
Check Serial Port
→ Finish.
7. On your PC, click Active-
Sync
→ Connection Set-
ting
→ Select COM Port
(COM 14)
→ OK
8. On the PA6008 tap Start
→
Programs
→ ActiveSync →
Menu
→ Connect via
Bluetooth.
28
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 3 Getting Connected
WiFi Connection
With the device’s embedded WLAN module, you can send and receive signals to a
WiFi network then synchronize files.
NOTE:
WiFi access requires a separate purchase of a service contract with a wireless service provider. Contact a wireless service provider for more information.
A wireless network can be added either when the network is detected or by manually entering settings information. Before doing these steps, determine if authentication information is needed.
1. Tap Start
→ Settings, then tap the Connections tab.
2. Tap Network Cards.
The Configure Network Adapters screen appears.
3. Select whether the network card connects to the Internet or your work LAN from the drop-down list.
4. If there are networks already detected, tap and hold network name, then select
Connect.
5. Under the Network to access, select from the following network connection options:
– All available
– Only access points
– Only computer-to-computer
6. When finished, tap OK.
For more information on how to configure the wireless network settings, tap Start
→ Help.
29
Synchronizing Information
All files created on the device are stored in My Document/PA600 My Document folder
(if the designated device name is PA600). You can view files by double-clicking the
PA600 My Documents icon on your computer.
If you have enabled file synchronization, your PA600 files are automatically synchronized in the My Documents folder on your computer, unless a different name was chosen for PA600.
Synchronization Options
Synchronization options can be modified, including when you synchronize and what gets synchronized. In the Mobile Device window, click Tools
→ Sync Options.
For each type of information, the synchronization process can be hastened by limiting the amount of data to be synchronized. To do this, select a service and click the Settings button. After enabling a service, you must close and reopen the ActiveSync.
Using ActiveSync to Exchange Files
You can use ActiveSync to exchange information from your device your computer and vice versa. Changes you make to the information on one location will not affect the information on the other one. If you want to automatically update information on both your device and computer, synchronize the information instead.
You can copy two types of information to your device: files and Pocket Access Windows CE Store information.
The procedure below only applies to copying files. Refer to the ActiveSync Help on your computer for instructions on how to copy Pocket Access Windows CE Store information.
NOTE:
Files created on your computer may need to be converted by Active-
Sync so that they can be viewed and edited on your device, and vice versa.
To copy files:
1. Connect your device to your computer.
2. In ActiveSync on your computer, click Explore.
30
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 3 Getting Connected
Windows Explorer opens the Mobile Device window for your device.
3. Locate the file that you want to copy on your device or computer.
4. Do either one of the following:
– To copy the file to your device, right-click the file and click Copy. Place the cursor in the desired folder for your device, right-click, then click Paste.
– To copy the file to your computer, right-click the file and click Copy. Place the cursor in the desired folder for your computer, right click, then click Paste.
31
Chapter 4
Barcode Scanner Programs
Scan2Key
The Scan2Key application routes input from a scanner port to a keypad buffer, making all input from the scanner emulate input from the keypad. Using Scan2Key, scanned data can be directly input into a scanner port aware application such as MS Mobile
Word.
Scanner Setting
When it is necessary for the user to change the default barcode symbology for a different application, the Scanner Control Panel provides the ability to change default symbology, place delimiter characters behind scanned data, and save the settings.
Tap Start
→ Settings → System → Scanner
Settings to display the Scanner Control Panel.
32
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 4 Barcode Scanner Programs
Barcode Symbologies
Barcode
Symbology
Enable/
Disable
Check
Char/Digit verification
Transmit
Check
Char/digit
Lookland EAN YES
Codabar YES YES YES
Max/
Min
Length
Transmit
Leading
Digit
Other
Code 11
Code 128
Code 32
Code 39
YES
YES
YES
YES YES
YES
YES
Transmet Start/
Stop bits, CLSI format, *data length
* check digits, *data length
*data length
Transmit Tailing digit
For ASCII,
Transmit Start/Stop bits, Function
Code, Double label decoding,*data length, *double labels separator
*data length Code 93
Deta Code
EAN 128
YES
YES
YES
YES
Yes
YES
Yes Transmit Code ID,
* Field separator
EAN 13
EAN 8
YES
YES
YES
YES
YES
YES
Interleaved 2 of 5
YES YES YES
* Not suppress first or last digit, *data length
Fixed Length, * Not suppress first or last digit, *data length
Label Code
IV&V
YES
MSI/Plessey YES
YES
YES
Standard 2 of 5
Telepen
YES
YES
YES YES
* Check digit double module 10,
* data length
Fixed Length,
*Data Length
*Standard
Character Set
UPC A
UPC E
UPC/EAN
Group
YES
YES
YES
YES
YES
YES Zero Expension,NSC
Supplement 2,
Supplement 5,Insert
Space before supplement, most have supplement,
*Add-on code try level
* adjustable Scanner
Control
Panel,
V 3.0
33
Advance settings
Chapter 5
Adjusting Settings
This section describes how to adjust the settings of your device to accommodate your work habits.
To access Settings, tap Start
→ Settings.
The Settings screen appears.
From here can adjust such user configurable items as the backlight, auto power off timer, system volume, and processor speed. You can also assign functions to buttons, configure menus, enter owner information, and set up connections.
34
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 5 Advance settings
Checking the Main and Backup Battery Status
This section describes how to view the power level for both the main and backup battery. To minimize power consumption, you can define settings for the auto-off function and the processor’s operation speed.
To check the main and backup battery status:
1. Open Power Properties. Do either of the following:
– If the Plug or Battery icon appears on your device, double-tap the icon to bring the Power Properties screen.
Plug icon
– Tap Start
→ Settings → System →
Power.
35
The Power screen appears.
2. The battery menu item displays the status of the main and backup batteries.
On the screen shown here, both batteries are at almost 100% charge.
NOTE:
It is necessary to charge the battery when the battery charge reaches below 10%. If the battery does not accept a charge, contact
Unitech Technical Support.
Extending Battery Life
You can extend the PA600 battery life by doing either of the following:
• Change the automatic power settings
• Minimize the use of backlight
Changing the Automatic Power Settings
The PA600 will enter idle mode when there is no task, or all tasks are waiting for input.
In default setting, the PA600 automatically turns itself off if it remains idle for 3 minutes and when there is no external charging power connected. Pressing the power button returns the PA600 to the same point at the time of automatic shutdown.
To change the automatic power settings:
1. In the Power screen tap the Advanced tab.
2. Tap the automatic shut off time arrow to select from a list of time periods. The available time periods are 1, 2, 3, 4, and 5 minutes.
3. This function can also be activated when the PA600 is plugged into the power adapter or placed in its docking station by tapping the On external power check box and then tapping the arrow to select from a list of time periods. The available time periods are 1, 2, 5,10, 15 and 30 minutes.
36
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 5 Advance settings
Adjusting Backlight Setting
The power consumption of the LCD backlight is high, turn off the backlight function if it is not necessary.
If a backlight is required, set “automatically turn off the backlight” function.
To change backlight settings:
1. Tap Start
→ Settings → System.
2. Tap Backlight.
The Backlight screen appears.
3. Do any of the following:
– In the Battery Power tab, tap the Turn
off backlight if device is not used for check box and select the amount of time before the unit turns off the backlight while running in battery power mode from the drop-down list.
– In the External Power tab, tap the Turn
off backlight if device is not used for check box and select the amount of time before the unit turns off the backlight while running in battery power mode from the drop-down list.
– Tap the Turn on the backlight key... checkbox to activate the backlight when the software keyboard is enabled.
37
– In the Brightness tab, tap and drag the slider to choose a dimmer backlight when operating on battery power.
Viewing Flash Memory Files
Flash memory is rewritable location for programs and data files. The benefit of this feature is that files and programs saved in Flash Memory are unaffected by the PA600 power status.
To access the Flash Memory files:
1. Connect the device to your computer. See page 24.
2. On your computer, click My Computer > Flash Storage.
To transfer files to Device’s Flash Memory:
1. Connect the device to your computer. See page 24.
2. On your computer, click My Computer > Flash Storage.
3. Select the file that you want to save.
4. Click File > Save To and select Flash Storage.
38
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 5 Advance settings
Performing a hardware reset
You may have to perform a reset if the device freezes (i.e., device no longer responds to the buttons on the screen).
A soft reset allows your device to get a fresh start, similar to rebooting a computer.
This will restart your device and adjust memory allocation. All records and entries are retained after a soft reset. Unsaved data in open programs may in some cases be lost.
Performing a Warm Boot
1. Remove the stylus from its holder.
2. Lightly press the tip of the stylus to the reset button located on the rear of the
PA600.
Reset button
39
Preforming a Cool Boot
A hard reset cuts off power to your device, erasing all records and entries, deleting all programs you have added, and restoring the device to default factory settings.
Never perform a hard reset unless a soft reset does not correct your problem. When you perform your next ActiveSync operation, you can restore any data that you previously synchronized to your computer or you can restore data that you backed up to a storage card.
NOTE:
When you perform a hard reset, the date and time settings are not be retained. Formats, preferences, and other settings are restored to their default factory settings.
Method 1
Follow these instructions to perform a cool boot.
1. Press and hold the Backspace key.
2. While holding the Backspace key, insert the tip of the stylus into the reset hole on the back of the
PA600 and press and hold the reset button until you see the
Unitech splash logo screen appear and then release the Backspace and reset buttons.
NOTE:
The system is returned to the default settings. All registry settings and all files (include the hidden files) are returned to their original factory defaults
40
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Method 2
1. Press and hold the TAB key.
Chapter 5 Advance settings
2. While holding the TAB key, insert the tip of the stylus into the reset hole on the back of the PA600 and press and hold the reset button until you see the Unitech splash logo screen appear and then release the TAB and reset buttons.
NOTE:
All registry settings are returned to default settings. You must reinstall all software. All files in flash memory are retained.
41
Appendix
System Specifications
Processing/Memory
Processing/Memory
OS
Keypad
Display
Scanner
Indicator
Communication
Audio
Expansion Slot
Power Source
Enclosure
Environmental
Models
Certification
Accessories
Software
CPU
CPU
Memory
Window Mobile 5.0 / Windows CE.NET 5.0
18-Key, including numeric key, alpha key and function key
240x320 QVGA, Color Transflective TFT, with Touch Screen & backlight
Laser Scan Engine, CCD Scan Engine as optional
Led, Vibrator
USB Host & Client
IrDA 1.2(SIR)
GPRS (Data Only)
802.11b for power saving
Bluetooth
Bluetooth supports Bluetooth Printer,
Bluetooth Modem,
Bluetooth ActiveSync
MIC
Speaker
Headset Connector
Receiver
SDIO slot
Main
Backup
Weight
Dimension
Operating temperature
Storage temperature
Relative Humidity
Drop test to Concrete
Environmental Sealing
GPRS + BT
802.11b + BT
BT Only
CE, FCC, BSMI, VCCI, RoHS compliant
Desktop Cradle
Battery Charger
4 slot Multi-Bay
Microsoft Visual Studio 2005
Microsoft Windows Mobile 5.0 SDK
Unitech PA600 SDK
VOIP (via 3rd party)
Intel PXA270 520MHz
Intel PXA270 520MHz
SDRAM:64MB
Flash ROM:128MB
3.7V 1950mAH Li-ion battery pack
One rechargeable Ni-MH backup battery
Under 300g with battery & scan engine
Approximately L149.5 X H26.6 X
W85mm
0 C~ 50 C
-20 C~ 60 C
5% ~ 95%(non-condensing)
4 feet
IP54
Vehicle Quick Charging Cable
Holster
42
Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Advertisement