- Sanatana Blog

- Sanatana Blog
Available ARM boards
at Sanatana Techtronics
Sanatana Techtronics
w w w . sa n a t a n a t e c h . c o m
06 May
Contents
1. ARM7 series
 Blueboard – LPC2148-H
 Blueboard – LPC2148-S
 Blueboard – LPC214x
 Mbed– Xpresso Baseboard
 mx– LPC2148-S
 LPC2148-EDU KIT
 Blueboard Base
2. Cortex M0 series
 Blueboard – LPC114
 Blueboard – LPC115
 Blueboard – LPC11U14
 Blueboard – LPC11U24
 Blueboard – LPC11U37
 mX-LPC1114-S
 mX-LPC11U14-S
3. Cortex M3 series
 Blueboard LPC1768 COMBO
 BlueBoard-LPC1343
 BlueBoard-LPC1768-H
 Blueboard-LPC1768-S
 mX-LPC1768-S
 mX-LPC1343-S
 LPC1830-Xplorer
 LPC1768-Xplorer
4. Cortex M4 series


5. Jtag


www.sanatanatech.com
LPC4330-Xplorer
LPC4357-Xplorer++
NGX ARM USB JTAG
NGX PARALLEL PORT JTAG
2
1. ARM7 series
a) BLUEBOARD-LPC2148-H (Rs 1199)
BlueBoard-LPC214X-H is a breakout board for LPC2148 ARM7TMDI based microcontroller. The
LPC2148 microcontroller has 512KB of internal flash and 32+8K RAM, can be clocked up to 60Mhz.
LPC2148 features include USB 2.0 device, 2xUARTs, RTC, 2x10bit ADCs each ADC has multiple
channels, 1xDAC, 6XPWM, 2xI2C, 1xSPI, 1XSSP, 2x32-bit TIMERS, FAST I/0 support and WDT.
LPC2148 also supports In System Programming (ISP)
Features:
• Dimensions: 85.95x53.62 mm2
• Two layer PCB (FR-4 material)
• Power: USB powered
• ISP and reset switch
• Test LED
• 32Khz crystal for RTC
• Extension headers for all microcontroller pins
• 1 RS232 port for ISP
• USB B-type connector with Link-LED
• 20pin - JTAG connector
www.sanatanatech.com
3
b) BLUEBOARD-LPC2148-S (Rs 899)
BlueBoard-LPC214X-S is a stamp board for NGX’s Blueboard Base. The LPC2148 microcontroller has
512KB of internal flash and 32+8K RAM,can be clocked up to 60Mhz. LPC2148 features include USB
2.0 device, 2xUARTs, RTC, 2x10bit ADCs each ADC has multiple channels, 1xDAC, 6XPWM, 2xI2C,
1xSPI,1XSSP, 2x32-bit TIMERS, FAST I/0 support and WDT. LPC2148 also supports In System
Programming (ISP).
Features:
• Dimensions: 47x47 mm2
• Two layer PCB (FR-4 material)
• 12MHz crystal
• 32Khz crystal for RTC
www.sanatanatech.com
4
c) BLUEBOARD-LPC214X ( Rs 2249)
The LPC2148 microcontroller has 512KB of internal flash and 32+8K RAM, can be clocked up to
60Mhz. LPC2148 features include USB 2.0 device, 2xUARTs, RTC, 2x10bit ADCs each ADC has
multiple channels, 1xDAC, 6XPWM, 2xI2C, 1xSPI, 1XSSP, 2x32-bit TIMERS, FAST I/0 support and
WDT. LPC2148 also supports In System Programming (ISP)
Features:
• Dimensions: 127 X 127 mm2
• Two layer PCB (FR-4 material)
• Power: DC 6.5V with power LED On-board linear regulators generate +3.3V/500mA
• and +5V/500mA from power supply USB connector (as alternate power source)
• ISP and reset switch
• 12.0000 MHz crystal for MCU,32Khz crystal for RTC
• Extension headers for all microcontroller pins
• RS232 connector (2x), VGA connector, PS2 connector, 20pin - JTAG connector,
• SD/MMC card connector, USB type-B connector with link-LED
• All peripheral configurable via jumper
• Audio power amplifier
• 2 line X 16 character LCD
• Backlight control for LCD
• Configurable for manual and automatic program download (ISP) via serial port
• Two layer PCB (FR-4 material)
• 8 controllable LEDs on SPI
www.sanatanatech.com
5
d) mbed-Xpresso Baseboard (Rs 1999)
The mbed-Xpresso Baseboard makes it possible for you to get started with experiments and
prototyping immediately. The Baseboard can also be used together with the mbed module.It is
compatible with the LPCXpresso boards and with the mbed module. mbed-Xpresso BaseBoard and
Stamp modules together serve as an excellent platform to evaluate various architectures like ARM7,
CORTEX-M3, CORTEX-M0... etc. Here is the list of stamp modules that could be used with
Baseboard
mbed
LPC1768
Development
Board,LPC1114
LPCXpresso,
LPC1343
LPCXpresso,LPC1768 LPCXpresso,NGX LPC2148 Stamp,NGX LPC1768 Stamp
Features :
mbed-Xpresso Base board has various peripherals with configurable jumpers. Two 27 pin expansion
dual row header connectors (P9-P11) and (P10-P12) (female, 100mil pitch) for simple connection to
breadboard.
(1) Note: The features mentioned for the mbed-Xpresso Base board in this document are directly
dependent on the Stamp board(microcontroller) used.
HARDWARE
• Dimensions of
115 X 155 mm2
• Two layer
(FR4 material)
POWER
 Power supply:
7.5Vwith power
LED
 On-board linear
regulators generate
+3.3V/500mA and
+5v/500mA from
power supply
 USB connector (as
alternate power
source)
www.sanatanatech.com
CONNECTORS









Extension headers for
all microcontroller
pins
Two RS232 port
connectors
VGA connector
PS/2 connector
JTAG connector
SD/MMC connector
RJ45 connector
USB B-type connector
All peripheral
configurable via
jumpers
PERIPHERALS
 256Kb I2C based
EPROM
 Audiopower amplifier
with audio jack
 2line X 16 character
LCD with back light
control
 Configurable for
manual and automatic
program download
(ISP) via serial port
6
e) mX-LPC2148-S (Rs 1199)
mX-LPC2148-S is a stamp board for NGX’s mbed-Xpresso Baseboard. The LPC2148 microcontroller
has 512KB of internal flash and 32+8K RAM, can be clocked up to 60Mhz. LPC2148 features include
USB 2.0 device, 2xUARTs, RTC, 2x10bit ADCs each ADC has multiple channels, 1xDAC, 6XPWM,
2xI2C, 1xSPI, 1XSSP, 2x32-bit TIMERS, FAST I/0 support and WDT. LPC2148 also supports In
System Programming (ISP)
Features
• Dimensions: 27x84 mm2
• Two layer PCB (FR-4 material)
• PCB Finish:ENIG
• On-board Test Led
• 12MHz crystal
• 32Khz crystal for RTC
www.sanatanatech.com
7
f) LPC2148-EDU KIT (Rs 5999)
The LPC2148-EDU tool kit contains the following items:
• LPC2148-EDU board
• power supply
• One USB cable
• One serial RS232 cable
• Graphic LCD
• CD which contains, KEIL evaluation version installer, Flash Magic Installer, schematics, user
manual, hex files for experiments, Keil project and workspace for implementing all the experiments
Features:
Here is the list of the main board components and interfaces:
• 4X4 Keypad
• 128X64 graphic LCD with backlight
• 16X2 character LCD with backlight
• 2 UART ports
• Temperature sensor
• Buzzer interface
• User potentiometer connected to ADC interface
• 8 user LED’s and buttons
• I2C interface with EEPROM, RTC and seven segment display
• USB interface
• Relay circuit
• Stepper motor
• JTAG port
www.sanatanatech.com
8
g) BLUEBOARD BASE (Rs 1799)
BlueBoard Base is modular approach to the ever evolving design of our flagship product BlueboardLPC2148. It is designed considering budget constraint of a hobby enthusiast who would be trying out
different controllers but would not be willing to invest in different boards for each controller. For all
these, the user can buy the required stamp module and work on this board.
BlueBoard Base and Blueboard Stamp modules together serve as an excellent platform to evaluate
various architectures like ARM7, CORTEX-M3, CORTEX-M0... etc.
Features:
HARDWARE
POWER
• Dimensions of
114 X 127 mm2
 Power supply: DC 6.512V i/p with power
LED
• Two layer
(FR4 material)
 On-board linear
regulators generate
+3.3V/500mA and
+5v/500mA from
power supply
• PCB finish: ENIG
 USB connector (as
alternate power
source)
www.sanatanatech.com
CONNECTORS








Extension headers for
all microcontroller
pins
Two RS232 port
connectors
VGA connector
PS/2 connector
JTAG connector
SD/MMC connector
USB B-type connector
with Link-LED
All peripheral
configurable via
jumpers
PERIPHERALS
 256Kb I2C based
EPROM
 Audiopower amplifier
with audio jack
 2line X 16 character
LCD with back light
control
 Configurable for
manual and automatic
program download
(ISP) via serial port
 8 controllable LEDs on
SP using 74HC595
9
2. Cortex M0 series
a) BlueBoard-LPC1114 (Rs 3499)
The LPC1114 is a NXP ARM CORTEX-M0 microcontroller, has 32KB of internal flash and 8KB SRAM.
The LPC1114 operate at CPU frequencies of up to 50MHz. In-System Programming (ISP) and InApplication Programming (IAP) via on-chip bootloader software. Programmable WatchDog Timer
(WDT). 1 x UART,1 x I2C-bus interfaces Fast-mode Plus with a data rate of 1 Mbit/s. 1 x SSP
controllers, 8-channel 10-bit ADC, Four general purpose counter/timers with a total of four capture
inputs and 13 match outputs. Integrated PMU power on reset and up to 42 general purpose I/O pins.
GPIO pins can be used as edge and level sensitive interrupt sources.
Following are the salient features of the board

Dimensions: 110mm X 110mm

Two layer PCB (FR-4 material)

Power: DC 6.5V with power LED On-board linear regulators generate +3.3V/500mA and
5V/500mA from power supply USB connector (as alternate power source)

10 pin, 20 pin CORTEX debug connector for SWD (Serial Wire Debug)

ISP, Wakeup, External Interrupt and reset switch

12.0000 MHz crystal for MCU, 32Khz crystal for RTC

Extension headers for all microcontroller pins

RS232 connector, PS2 connector, Micro SD/MMC card connector, USB type-B mini
connector with link-LED

64 x 128 graphical LCD with Backlight control

High accuracy external RTC connected on I2C bus

RTC battery holder

10K pot for ADC
www.sanatanatech.com
10
b) BlueBoard-LPC1115 (Rs 3499)
The LPC1115 is a NXP ARM CORTEX-M0 microcontroller, has 64KB of internal flash and 8KB SRAM.
The LPC1114 operate at CPU frequencies of up to 50MHz. In-System Programming (ISP) and InApplication Programming (IAP) via on-chip bootloader software. Programmable WatchDog Timer
(WDT). 1 x UART,1 x I2C-bus interfaces Fast-mode Plus with a data rate of 1 Mbit/s. 1 x SSP
controllers, 8-channel 10-bit ADC, Four general purpose counter/timers with a total of four capture
inputs and 13 match outputs. Integrated PMU power on reset and up to 42 general purpose I/O pins.
GPIO pins can be used as edge and level sensitive interrupt sources.Following are the salient features
of the board

Dimensions: 110mm X 110mm

Two layer PCB (FR-4 material)

Power: DC 6.5V with power LED On-board linear regulators generate +3.3V/500mA and
+5V/500mA from power supply USB connector (as alternate power source)

10 pin, 20 pin CORTEX debug connector for SWD (Serial Wire Debug)

ISP, Wakeup, External Interrupt and reset switch

12.0000 MHz crystal for MCU, 32Khz crystal for RTC

Extension headers for all microcontroller pins

RS232 connector, PS2 connector, Micro SD/MMC card connector, USB type-B mini connector
with link-LED

64 x 128 graphical LCD with Backlight control

High accuracy external RTC connected on I2C bus

RTC battery holder

10K pot for ADC
www.sanatanatech.com
11
c) BlueBoard-LPC11U14 (Rs 3499)
The LPC11U14 is a NXP ARM CORTEX-M0 microcontroller has 32KB of internal flash and 8KB
SRAM. The LPC11U14 operate at CPU frequencies of up to 50MHz. In-System Programming (ISP) and
In-Application Programming (IAP) via on-chip bootloader software. Programmable WatchDog Timer
(WDT). 1 x UART,1 x I2C-bus interfaces Fast-mode Plus with a data rate of 1 Mbit/s. 1 x SSP
controllers, 8-channel 10-bit ADC, Four general purpose counter/timers with a total of four capture
inputs and 13 match outputs. Integrated PMU power on Reset and up to 42 general purpose I/O pins.
GPIO pins can be used as edge and level sensitive interrupt sources.
Following are the salient features of the board
• Dimensions: 110mm X 110mm
• Two layer PCB (FR-4 material)
• Power: DC 6.5V with power LED On-board linear regulators generate +3.3V/500mA and
+5V/500mA from
power supply USB connector (as alternate power source)
• 10 pin, 20 pin CORTEX debug connector for SWD (Serial Wire Debug)
• ISP, Wakeup, External Interrupt and reset switch
• 12.0000 MHz crystal for MCU, 32Khz crystal for RTC
• Extension headers for all microcontroller pins
• RS232 connector, PS2 connector, Micro SD/MMC card connector, USB type-B mini connector with
link-LED
• 64 x 128 graphical LCD with Backlight control
• High accuracy external RTC connected on I2C bus
• RTC battery holder
• 10K pot for ADC
www.sanatanatech.com
12
d) BlueBoard-LPC11U24 (Rs 3499)
The LPC11U24 is a NXP ARM CORTEX-M0 microcontroller with a USB 2.0 full-speed device
controller, has 32KB of internal flash, 8+2 KB SRAM and 4KB EEPROM. The LPC11U24 operates at
CPU frequencies of up to 50MHz. In-System Programming (ISP) and In-Application Programming
(IAP) via on-chip bootloader software. The peripheral complement of the LPC11U24 includes, one
Fast-mode Plus I2C-bus interface, one RS-485/EIA-485 USART with support for synchronous mode
and smart card interface, two SSP interfaces, four general purpose counter/timers, a 10-bit ADC, and
upto 40 general purpose I/O pins.
Following are the salient features of the board
• Dimensions: 110mm X 110mm
• Two layer PCB (FR-4 material)
• Power: DC 6.5V with power LED On-board linear regulators generate +3.3V/500mA and
+5V/500mA from
power supply USB connector (as alternate power source)
• 10 pin, 20 pin CORTEX debug connector for SWD (Serial Wire Debug)
• ISP, Wakeup, External Interrupt and reset switch
• 12.0000 MHz crystal for MCU, 32Khz crystal for RTC
• Extension headers for all microcontroller pins
• RS232 connector, PS2 connector, Micro SD/MMC card connector, USB type-B mini connector with
link-LED
• 64 x 128 graphical LCD with Backlight control
• High accuracy external RTC connected on I2C bus
• RTC battery holder
• 10K pot for ADC
www.sanatanatech.com
13
e) BlueBoard-LPC11U37 (Rs 3499)
The LPC11U37, a NXP ARM CORTEX-M0 microcontroller is a USB 2.0 full-speed device controller,
has 128KB of internal flash, 10 KB SRAM and 4KB EEPROM. The LPC11U37 operates at CPU
frequencies of up to 50MHz. In-System Programming (ISP) and In-Application Programming (IAP)
via on-chip bootloader software. The peripheral complement of the LPC11U37 includes, one Fastmode Plus I2C-bus interface, one RS-485/EIA-485 USART with support for synchronous mode and
smart card interface, two SSP interfaces, four general purpose counter/timers, a 10-bit ADC, and upto
40 general purpose I/O pins.
Following are the salient features of the board
• Dimensions: 110mm X 110mm
• Two layer PCB (FR-4 material)
• Power: DC 6.5V with power LED On-board linear regulators generate +3.3V/500mA and
+5V/500mA from
power supply USB connector (as alternate power source)
• 10 pin, 20 pin CORTEX debug connector for SWD (Serial Wire Debug)
• ISP, Wakeup, External Interrupt and reset switch
• 12.0000 MHz crystal for MCU, 32Khz crystal for RTC
• Extension headers for all microcontroller pins
• RS232 connector, PS2 connector, Micro SD/MMC card connector, USB type-B mini connector with
link-LED
• 64 x 128 graphical LCD with Backlight control
• High accuracy external RTC connected on I2C bus
• RTC battery holder
• 10K pot for ADC
www.sanatanatech.com
14
f) mX-LPC11U14-S (Rs 899)
mX-LPC11U14-S is a CORTEX-M0 based stamp board for NGX’s mbed-Xpresso Baseboard. The
LPC11U14 microcontroller has 32KB of internal flash and 8KB SRAM. The LPC11U14 operate at CPU
frequencies of up to 50MHz. In-System Programming (ISP) and In-Application Programming (IAP)
via on-chip bootloader software. Programmable WatchDog Timer (WDT). 1 x UART,1 x I2C-bus
interfaces Fast-mode Plus with a data rate of 1 Mbit/s. 1 x SSP controllers, 8-channel 10-bit ADC,
Four general purpose counter/timers with a total of four capture inputs and 13 match outputs.
Integrated PMU , power on Reset and up to 42 general purpose I/O pins. GPIO pins can be used as
edge and level sensitive interrupt sources.
Following are the salient features of the board:
• Dimensions: 126x35 mm2
• Two layer PCB (FR-4 material)
• On-board Test Led
• 12MHz crystal
• On board debugger
• No power supply required, powered through USB
www.sanatanatech.com
15
g) mX-LPC1114-S (Rs 899)
mX-LPC1114-S is a CORTEX-M0 based stamp board for NGX’s mbed-Xpresso Baseboard. The
LPC1114 microcontroller has 32KB of internal flash and 8KB SRAM. The LPC1114 operate at CPU
frequencies of up to 50MHz. In-System Programming (ISP) and In-Application Programming (IAP)
via on-chip bootloader software. Programmable WatchDog Timer (WDT). 1 x UART,1 x I2C-bus
interfaces Fast-mode Plus with a data rate of 1 Mbit/s. 1 x SSP controllers, 8-channel 10-bit ADC,
Four general purpose counter/timers with a total of four capture inputs and 13 match outputs.
Integrated PMU , power on Reset and up to 42 general purpose I/O pins. GPIO pins can be used as
edge and level sensitive interrupt sources.
Following are the salient features of the board:
• Dimensions: 126x35 mm2
• Two layer PCB (FR-4 material)
• On-board Test Led
• 12MHz crystal
• On board debugger.
• No power supply required, powered through USB
www.sanatanatech.com
16
3. Cortex M3 series
a) Blueboard LPC1768 COMBO (Rs 2799)
Blueboard LPC1768 COMBO is the complete package for starting up with the development with
CORTEX-M3 architecture.This consists of Blueboard Base
with LPC1768 stamp. BlueBoard use and Blueboard LPC1768 Stamp module together serve as an
excellent platform to evaluate CORTEX-M3 architecture.
The LPC1768 microcontroller has 512KB of internal flash and 64KB RAM. Ethernet MAC,
USB Device/Host/OTG interface, 8-channel general purpose DMA controller, 4 UARTs, 2 CAN
channels, 2 SSP controllers, SPI interface, 3 I2C-bus interfaces, 2-input plus 2-output I2S-bus
interface, 8-channel 12-bit ADC, 10-bit DAC, motor control PWM, Quadrature Encoder interface, 4
general purpose timers, 6-output general purpose PWM, ultra-low power Real-Time Clock (RTC) with
separate battery supply, and up to 70 general purpose I/O pins .
HARDWARE
POWER
• Dimensions of
114 X 127 mm2
 Power supply: DC 6.512V i/p with power
LED
• Two layers
(FR4 material)
 On-board linear
regulators generate
+3.3V/500mA and
+5v/500mA from
power supply
• PCB finish: ENIG
 USB connector (as
alternate power
source)
www.sanatanatech.com
CONNECTORS







Extension headers for
all microcontroller
pins
Two RS232 port
connectors
VGA connector
PS/2 connector
JTAG connector
SD/MMC connector
All peripheral
configurable via
jumpers
PERIPHERALS
 256Kb I2C based
EPROM
 Audiopower amplifier
with audio jack
 2line X 16 character
LCD with back light
control
 Configurable for
manual and automatic
program download
(ISP) via serial port
 8 controllable LEDs on
SP using 74HC595
17
b) BlueBoard-LPC1343 (Rs 3499)
The LPC1343 is a NXP ARM CORTEX-M3 microcontroller has 32KB of internal flash and 8KB SRAM.
In-System Programming (ISP) and In-Application Programming (IAP) via on-chip bootloader
software, Programmable WatchDog Timer (WDT). 1 x UART,1 x I2C-bus interfaces Fast-mode Plus
with a data rate of 1 Mbit/s. 1 x SSP controllers, 8-channel 10-bit ADC, USB 2.0 full-speed device
controller with on-chip PHY for device, motor control PWM, Four general purpose counter/timers
with a total of four capture inputs and 13 match outputs. And up to 42 general purpose I/O pins.
GPIO pins can be used as edge and level sensitive interrupt sources.
Following are the salient features of the board
• Dimensions: 110mm X 110mm
• Two layer PCB (FR-4 material)
• Power: DC 6.5V with power LED On-board linear regulators generate +3.3V/500mA and
+5V/500mA from power supply USB connector (as alternate power source)
• 10 pin, 20 pin CORTEX debug connector for SWD (Serial Wire Debug)
• ISP, Wakeup, External Interrupt and reset switch
• 12.0000 MHz crystal for MCU, 32Khz crystal for RTC
• Extension headers for all microcontroller pins
• RS232 connector, PS2 connector, Micro SD/MMC card connector, USB type-B mini connector with
link-LED
• 64 x 128 graphical LCD with Backlight control
• High accuracy external RTC connected on I2C bus
• RTC battery holder
• 10K pot for ADC
www.sanatanatech.com
18
c) BLUEBOARD-LPC1768-H (Rs 1499)
BlueBoard-LPC1768-H is a breakout board for LPC1768 cortex-M3 based microcontroller. The
LPC1768 microcontroller has 512KB of internal flash and 64KB RAM. Ethernet MAC, USB Device/
Host /OTG interface, 8-channel general purpose DMA controller, 4 UARTs, 2 CAN channels, 2 SSP
controllers, SPI interface, 3 I2C-bus interfaces, 2-input plus 2-output I2S-bus interface, 8-channel 12bit ADC, 10-bit DAC, motor control PWM, Quadrature Encoder interface, 4 general purpose timers,
6-output general purpose PWM, ultra-low power Real-Time Clock (RTC) with separate battery supply,
and up to 70 general purpose I/O pins
Features:
• Dimensions: 94.08x54.48 mm2
• Two layer PCB (FR-4 material)
• Power: USB powered or can be powered through the DC jack, 5-7.5V input
• reset switch
• Test LED
• 32Khz crystal for RTC
• On board 258kb I2C EERPOM
• Extension headers for all microcontroller pins
• USB B-type connector for powering the board
• 20pin - JTAG connector
www.sanatanatech.com
19
d) BLUEBOARD-LPC1768-S (Rs 1099)
BlueBoard-LPC1768-S is a stamp board for NGX’s Blueboard Base. The LPC1768 microcontroller has
512KB of internal flash and 64KB RAM.Ethernet MAC, USB Device/Host/OTG interface, 8-channel
general purpose DMA controller, 4 UARTs, 2 CAN channels, 2 SSP controllers, SPI interface, 3 I2Cbus interfaces, 2-input plus 2-output I2S-bus interface, 8-channel 12-bit ADC, 10-bit DAC, motor
control PWM, Quadrature Encoder interface, 4 general purpose timers, 6-output general purpose
PWM, ultra-low power Real-Time Clock (RTC) with separate battery supply, and up to 70 general
purpose I/O pins
Features:
• Dimensions: 47x47 mm2
• Two layer PCB (FR-4 material)
• 32Khz crystal for RTC
• 12MHz crystal
• Test LED
www.sanatanatech.com
20
e) mX-LPC1768-S (Rs 2199)
mX-LPC1768-S is a CORTEX-M3 based stamp board for NGX’s mbed-Xpresso Baseboard. The
LPC1768 microcontroller has 512KB of internal flash and 64KB RAM. Ethernet MAC, USB
Device/Host/OTG interface, 8-channel general purpose DMA controller, 4 UARTs, 2 CAN channels, 2
SSP controllers, SPI interface, 3 I2C-bus interfaces, 2-input plus 2-output I2S-bus interface, 8channel 12-bit ADC, 10-bit DAC, motor control PWM, Quadrature Encoder interface, 4 general
purpose timers, 6-output general purpose PWM, ultra-low power Real-Time Clock (RTC) with
separate battery supply, and up to 70 general purpose I/O pins
Features:
• Dimensions: 27x84 mm2
• On-board Test Led
• 12MHz crystal
• 50Mhz oscillator for Ethernet
• On board USB Host / Device support
• On board Ethernet Transceiver
• On board dual port USB power switch and Over-current protection
www.sanatanatech.com
21
f) mX-LPC1343-S (Rs 899)
mX-LPC1343-S is a CORTEX-M3 based stamp board for NGX’s mbed-Xpresso Baseboard. The
LPC1343 microcontroller has 32KB of internal flash and 8KB SRAM. In-System Programming (ISP)
and In-Application Programming (IAP) via on-chip bootloader software.Programmable WatchDog
Timer (WDT). 1 x UART,1 x I2C-bus interfaces Fast-mode Plus with a data rate of 1 Mbit/s. 1 x SSP
controllers, 8-channel 10-bit ADC, USB 2.0 full-speed device controller with on-chip PHY for
device,motor control PWM, Four general purpose counter/timers with a total of four capture inputs
and 13 match outputs. And up to 42 general purpose I/O pins.GPIO pins can be used as edge and level
sensitive interrupt sources.
Following are the salient features of the board:
• Dimensions: 126x35 mm2
• Two layer PCB (FR-4 material)
• On-board Test Led
• 12MHz crystal
• On board debugger.
• No power supply required, powered through USB
www.sanatanatech.com
22
g) LPC1830-Xplorer (Rs 2499)
LPC1830-Xplorer is a breakout board for LPC1830 cortex-M3 based microcontroller. The LPC1830
microcontroller has flash and flashless parts. For flashless microcontroller has 200KB SRAM, two
32KB SRAM blocks with separate bus. 64KB ROM containing boot code and on-chip software drivers.
32-bit OTP. For flash microcontroller 1MB dual bank flash, 136KB SRAM, Ethernet MAC, one USB
2.0 Device/Host/OTG interface with DMA support, one USB2.0 Host/Device interaface with DMA,
on-chip full-speed PHY and ULPI interface to external high-speed PHY, 4 UARTS with DMA support,
2 C_CAN 2.0B, 2 SSPs, 2 I2C, 2 I2S, LCD controller, 8 GPDMA, up to 164 GPIO, 1 10-bit DAC, 2 10bit ADCs, and RTC.
LPC1830-Xplorer has been developed in partnership with NXP semiconductors Inc.
Following are the salient features of the board
• Controller: LPC1830, 100 pin BGA
• PCB: 4-layer (86mm x 40mm, RoHS Compliant)
• Two LEDs
• One user switch and one reset switch
• Boot select switch
• 32Mb Quad flash
• On board crystals for controller, RTC and audio codec
• On board Ethernet PHY, 50 MHz Oscillator and RJ45 connector with magnetics
• On board audio codec and audio jacks
• On board USB host power switch
• On board Micro SD card slot
• Two USB ports, one HS (High speed) port and one FS (Full Speed) port
• 10-pin cortex debug header
• Unused I/Os brought to a header
www.sanatanatech.com
23
h) LPC1768-Xplorer ( Rs 2399 )
LPC1768-Xplorer is a CORTEX-M3 based stamp board for NGX’s mbed-Xpresso Baseboard. The
LPC1768 microcontroller has 512KB of internal flash and 64KB RAM. Ethernet MAC, USB
Device/Host/OTG interface, 8-channel general purpose DMA controller, 4 UARTs, 2 CAN channels, 2
SSP controllers, SPI interface, 3 I2C-bus interfaces, 2-input plus 2-output I2S-bus interface, 8channel 12-bit ADC, 10-bit DAC, motor control PWM, Quadrature Encoder interface, 4 general
purpose timers, 6-output general purpose PWM, ultra-low power Real-Time Clock (RTC) with
separate battery supply, and up to 70 general purpose I/O pins
Following are the salient features of the board:
• Dimensions: 27x101 mm2
• On-board Test Led
• 12MHz crystal
• 25Mhz crystal for Ethernet
• 32KHz RTC crystal
• On board USB Host / Device support
• On board Ethernet Transceiver
• On board dual port USB power switch and Over-current protection
• On board Micro-SD card holder
• On board 10 pin SWD
• On board reset switch
www.sanatanatech.com
24
4. Cortex M4 series
a) LPC4330-Xplorer (Rs 2499)
LPC4330-Xplorer is a breakout board for LPC4330 cortex-M4 based microcontroller. The LPC4330
microcontroller has flash and flashless parts. For flashless microcontroller has 200KB SRAM, two
32KB SRAM blocks with separate bus. 64KB ROM containing boot code and on-chip software drivers.
32-bit OTP. For flash microcontroller 1MB dual bank flash, 136KB SRAM, Ethernet MAC, one USB
2.0 Device/Host/OTG interface with DMA support, one USB2.0 Host/Device interaface with DMA,
on-chip full-speed PHY and ULPI interface to external high-speed PHY, 4 UARTS with DMA support,
2 C_CAN 2.0B, 2 SSPs, 2 I2C, 2 I2S, LCD controller, 8 GPDMA, up to 164 GPIO, 1 10-bit DAC, 2 10bit ADCs, and RTC.
LPC4330-Xplorer has been developed in partnership with NXP semiconductors Inc.
Following are the salient features of the board
• Controller: LPC4330, 100 pin BGA
• PCB: 4-layer (86mm x 40mm, RoHS Compliant)
• Two LEDs
• One user switch and one reset switch
• Boot select switch
• 32Mb Quad flash
• On board crystals for controller, RTC and audio codec
• On board Ethernet PHY, 50 MHz Oscillator and RJ45 connector with magnetics
• On board audio codec and audio jacks
• On board USB host power switch
• On board Micro SD card slot
• Two USB ports, one HS (High speed) port and one FS (Full Speed) port
• 10-pin cortex debug header
• Unused I/Os brought to a header
www.sanatanatech.com
25
b) LPC4357-Xplorer++(3499)
LPC4357-Xplorer++ is a cost effective evaluation platform for LPC4357 controller. The LPC4357 is a
ARM Cortex-M4 based microcontrollers for embedded applications which include an ARM Cortex-M0
coprocessor, up to 1 MB of flash and 136 kB of on-chip SRAM, 16 kB of EEPROM memory, advanced
configurable peripherals such as the State Configurable Timer (SCT) and the Serial General Purpose
I/O (SGPIO) interface, two High-speed USB controllers, Ethernet, LCD, an external memory
controller, and multiple digital and analog peripherals. The LPC4357 operate at CPU frequencies of up
to 204 MHz
Following are the salient features of the LPC4357-Xplorer++















Controller: LPC4357, 256 pin BGA
PCB: 6-layer (102mm x 43mm, RoHS Compliant)
Two LEDs
One user switch and one reset switch
On board Micro SD card slot
32Mb Quad flash
On board 32MB SDRAM on 32bit bus
On board crystals for controller, RTC and audio codec
On board Ethernet PHY, 25 MHz Crystal and RJ45 connector with magnetics
On board audio codec and audio jacks
On board USB host
On board USB Device
On board 2X RS232 UART connected to the header
10-pin cortex debug header
Unused I/Os brought to header
www.sanatanatech.com
26
5. Jtag
a) NGX ARM USB JTAG (Rs 1199)
Features:
• USB 2.0 Full Speed device (12 Mbits/sec) interface
• Can be used to debug and program all ARM processors supported by OpenOCD
• Provides a standard 2X10 pin JTAG interface
• Adds a virtual RS232 serial port to your computer or laptop
• No external power supply required – it runs off of the USB power from the host computer
• Complete schematic provided
• Supported by open source debugger OpenOCD and commercial tools like Crossworks
The ‘NGX ARM USB JTAG’ is a compact USB to JTAG in-circuit debugger and programmer
designed for ARM cores.It connects via USB to the host PC. The ‘NGX ARM USB JTAG’ provides a
standard 20-pin JTAG interface as well as a standard RS232 port.
It is based on FTDI's popular FT2232 Dual USB UART/FIFO integrated circuit. The FT2232 has two
devices integrated on it:
• Channel A: USB to JTAG interface
• Channel B: USB to SERIAL UART
JTAG Interface
It provides a standard ARM-compatible 20-pin JTAG interface. The JTAG interface enables
access to the on-chip debug module which is integrated into the ARM CPU. The debug module enables
a programmer to debug the software on an embedded target system.
Serial UART
NGX ARM USB JTAG’ serial port provides you with an independent functional "USB to RS-232"
serial device. For Linux, the RS232 driver for the FT2232 is part of the main kernel tree and is
provided in most standard Linux distributions. In Windows, you have to load the Windows driver for
the FT2232. Once the driver is loaded, Windows will assign a virtual COM port to the serial port. It
operates just like a standard COM port. You can use it on laptops or PC's that do not have a 9-pin
legacy serial connector.
www.sanatanatech.com
27
b) NGX PARALLEL PORT JTAG (Rs 249)
Features:
• Comes with standard 20-Pin JTAG connector
• Can be used to program and debug all ARM devices
• No external power supply required
• Comes with 7" ribbon cable to connect to the target board
• Dimensions: 50x50 mm
www.sanatanatech.com
28
c) NGX CoLinkEx (Rs 749)
NGX CoLinkEx ( derived from CooCox ) is a hardware debugging adapter which supports SW
debugging and supports both ARM Cortex M3 and Cortex M0 devices, it supports debugging in
CooCox software and Keil Realview MDK.
Features:






Board Dimension: 55mm x 35mm
Free
Supports Cortex M0 and Cortex M3 devices
Supports SW debugging
Supports JTAG debugging
Supports CoFlash, CoIDE, MDK and IAR
www.sanatanatech.com
29
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement