AUTOMATIC GATE OPERATORS Accessories - Fence

AUTOMATIC GATE OPERATORS Accessories - Fence
K
O
/
®
AUTOMATIC GATE OPERATORS
K
2
Y
Accessories
rev-5/19/99
©1998 GTO, Inc.
ACCESS-ories
1
2
3
4
5
6
7
8
9
GTO Digital Keypad (F300)
The specially designed weatherproof digital keypad can be easily installed as a wireless or wired
keypad for swing and slide gate operators, or as a wired keypad for the Bulldog Pedestrian Gate
Lock. It can be programmed to use up to fifteen different personal identification number (PIN)
codes. Each code is face programmable with additional security features built in. Requires 3 AA
batteries (not included). Can also accommodate most garage doors and other gate openers. If used
as a wired keypad, GTO low voltage, 16 gauge, dual conductor, multi-stranded, direct burial wire
will be required.
0
HEDDOLF
UNIVE
RSAL
MOREC
DEL EIV
294ER
GTO Entry Transmitter (RB741)
The GTO Entry Transmitter, with adjustable code settings is standard equipment with all GTO gate operator systems. Battery included.
GTO Dual Transmitter (RB742)
GTO Triple Transmitter (RB743)
The two and three button transmitters are used for the remote control of
two or three gate operators and/or
garage door openers (See Garage
Door Receiver). Battery included.
ATIC
OM CK ®
AUTE LOLO
CK
GASTECURITY
IC
ON
CTR
ELE
GTO Key Chain Mini Transmitter
(RB744)
The Key Chain Mini Transmitter is a
miniature version of the GTO entry
transmitter and has the same adjustable code settings. Battery included.
Push Button (doorbell) Control
(RB101)
Unlit doorbell button for remote
entry or exit control. Wires directly
to the control board using 16 gauge,
stranded, direct burial, low voltage
wire (not included).
GTO Automatic Gate Lock (FM144) for closed position pull-to-open applications
A MUST for added security. Driven by a 4 amp solenoid, the plated steel bolt lock has a zinc plated
steel housing. The horizontal electronic lock is used with all GTO swing gate operator systems for
additional security and stability. Comes with a keyed manual release.
GTO Automatic Gate Lock (FM142) for open position or push-to-open applications
Similar to FM144 but used to secure gates in the open position, or for push-to-open gate
applications (not shown).
GTO Bulldog Pedestrian Gate Lock (FM500)
Similar to the Automatic Gate Lock but designed for horizontal use only on "walk-thru" gates
without automatic operators. The Bulldog is an affordable solution to protecting swimming pool
areas, playgrounds, tennis courts, boat docks, etc., from unwanted access. Includes control box and
keyed manual release.
®
SECU
RITY
GAT
E LO
CK
Garage Door Receiver (RB709)
Allows the use of the same GTO remote transmitter (see Dual and
Triple Transmitters) to control the gate operator and garage door
opener. Compatible with most garage door openers.
, Inc.
Bulldog Digital Keypad (RB711)
The weatherproof digital keypad for the Bulldog Pedestrian Lock has an adjustable six digit code.
Installation is easy, using standard low voltage wire. The Bulldog control box is pre-wired for this
keypad accessory. Not for use with automatic gate openers
2
3
1
5
6
4
8
7
9
0
R
TE
EN
ACCESS-ories
4" (O.D.) Post Bracket (RB464)
Recommended for mounting GTO/
PRO 2000 to a 4" gate post.
4" (O.D.) Round Post Bracket
Adapters (RB469)
These adapters are necessary when
mounting the 4" post bracket to a 4"
(O.D.) gate post. Two required for
each gate. Use with 4" Post Bracket
(RB464).
65/8" (O.D.) Round Post Bracket
Adapters (RB467)
Similar to RB466, used with 65/8"
(O.D.) gate post. Two required for
each gate.
Replacement Receivers
The AQ201: Receiver with a 10
ft. cable (included).
The AWQ325: Receiver with a
25 ft. cable.
The AWQ350: Receiver with a
50 ft. cable.
The AWQ400: Receiver with a
100 ft. cable.
Column Mount Lock Receiver
(433IH)
For mounting the Automatic Gate
Lock or Bulldog Pedestrian Lock
on areas with limited space between
the gate and post, such as brick columns, walls, etc.
Column Mount Bracket (349IH)
For column installation of the GTO/
PRO 1000 series operators. Designed
for mounting the Post-Pivot Bracket
on masonry columns or any flat surface. Two Brackets are required
for each operator.
Push To Open (FM305)
Required when GTO/PRO 1000
series gate operator(s) must push the
gate open, such as on a sloping driveway or where space prevents gate(s)
from opening inward (pulled open).
Order two PTO kits for conversion of a dual swing gate installation.
Master® Pin Lock (RB975)
The pin lock substitutes for the clevis
pin at either or both mounting points of
the GTO/PRO 1000 series operator arm.
Helps prevent theft of the operator arm
while allowing quick release of the
operator.
The pin lock can be inserted in the chain
brackets of the GTO/PRO SL-1000 to
prevent unauthorized removal of the
quick release pins.
GTO Low Voltage Wire (RB509)
The 16 gauge, dual conductor, multistranded, direct burial, low voltage
wire is required to connect the control board to either the solar panel or
the AC transformer. This wire is also
required for installation of some accessories such as keypads, locks, or
push buttons.
Standard Replacement Power
Cables for Gate Operators
The PRO 4.5C (AW203): 4.5 ft.
power cable included with GTO/
PRO 1000 or GTO/PRO 1800
single gate operators.
The PRO 25C (AW204): 25 ft.
power cable included with GTO/
PRO 1200 dual (second) gate operator.
The PRO 35C (AC108) and PRO
40C (AC109): 35 and 40 ft. "Quick
Connect" power cables for GTO/
PRO 1000 series operators; allow
the control box to be mounted in a
more remote location, away from
the gate.
The PRO 6C (AW209): 6 ft. power
cable included with GTO/PRO
2000 single gate operators.
The PRO 50C (AW210): 50 ft.
power cable included with GTO/
PRO 2200 dual (second) gate operator.
The PRO 60C (AC202): 60 ft.
Power cable included with GTO SL1200 dual (second) slide gate operator.
ACCESS-ories
Standard Replacement Transformer
RB502 – Standard 14 volt AC transformer for maintaining the battery included with the GTO/PRO 1000 gate
operator.
RB418 – Standard 18 volt AC transformer for maintaining the battery included with the GTO/PRO 1800 gate
operator.
Heavy Duty Replacement Transformer
RB419 – Heavy Duty 14 volt AC continuous cycle duty transformer (see wire chart in installation manual) for
maintaining the battery included with the GTO/PRO 2000 and GTO/PRO SL-1000.
Bulldog Replacement Charger
RB421 – Standard 12 volt DC charger (not shown) for maintaining battery included with the Bulldog
Pedestrian Gate Lock.
These are the only transformers approved for use with the GTO/PRO gate operators. For older model operators,
call for assistance.
Replacement Battery (RB500)
The standard 12 volt, 7.0 amp-hour, maintenance-free battery for all GTO/PRO gate operators. This battery is
the only battery approved for use with GTO Operators. Life expectancy is 3-5 years.
Replacement Battery (RB506)
The 6 volt, 7.0 amp-hour version for use in the GTO/PRO 1800 power system in conjunction with 12V battery
(RB500).
Replacement Battery (RB422)
The 12 volt, 1.2 amp-hour version for use with the Bulldog Pedestrian Gate Lock.
Operator Solar Panel (FM123 ) - Improved, Amorphous Silicon (Two Year Warranty*)
This 10 watt solar panel is a solar powered battery charger for use with GTO/PRO Automatic Gate Operator
systems. Particularly suited for remote installations, the solar panel comes with tubular steel support, mounting
clips, wire connectors, and 8 ft. of low voltage wire. (See Low Voltage Wire for additional wire.) Installation in
some regions of the world will require multiple panels for adequate charging power. Recommended for GTO/
PRO 2000/2200, GTO/PRO SL-1000/SL-1200 and GTO/PRO 1800.
Dual gate installations require minimum of two (2) FM123 solar panels for adequate charging power.
Operator Solar Panel (FM122 ) - Improved, Amorphous Silicon (Two Year Warranty*)
The 5 watt solar panel is a solar powered battery charger for use with GTO/PRO Automatic Gate Operator
systems. Particularly suited for remote installations, the solar panel comes with tubular steel support, mounting
clips, wire connectors, and 8 ft. of low voltage wire. (See Low Voltage Wire for additional wire.) All operators
are pre-wired for the solar panel. Installation in some regions of the world will require multiple panels for adequate
charging power. Recommended for GTO/PRO 1000, GTO/PRO 1200 and GTO/PRO 1800.
Bulldog Solar Panel (FM501)
The GTO Bulldog solar panel is a solar powered battery charger for use with the Bulldog Pedestrian Gate Lock
system. Particularly suited for pool areas where AC power is not preferred. The GTO Bulldog solar panel comes
with tubular steel support, mounting clips, wire connectors and 20 feet of low voltage wire. The Bulldog control
board is pre-wired for this solar panel accessory.
* GTO, Inc. gate operator accessories are warranted by the manufacturer against defects in materials and
workmanship for a period of one year, unless otherwise stated, from the date of purchase provided
recommended installation procedures have been followed. Warranty is considered void if damage was due
to improper installation or use, connection to an improper power source, or was caused by lightning, wind,
fire, flood, insects or other natural agent.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement