Hammond B-3P Owner's Manual

*#1
14)#0
Model $OM
%OM
$2OM
Thank you, and congratulations on your choice of this organ.
In order to get the most out of this instrument for many years to
come, first take the time to read this manual in full.
Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
Read these instructions.
Keep these instructions.
Only use attachments/accessories specified by the manufacturer.
Heed all warnings.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus. When cart is used: use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
Follow all instructions.
Do not use this apparatus near water.
Unplug this apparatus during lightning storms, or when unused
for long periods of time.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a
third grounding prong. The wider blade or third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed on
the apparatus.
WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
The lightning flash with arrowhead symbol within an equilateral triangle, indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
The exclamation point within equilateral triangle, indicates
that there are important operating and maintenance instructions in the literature accompanying this unit.
In case in the future your instrument gets too old to play/use or malfunctions beyond repair, please observe the instructions of this mark,
or, if any question, be sure to contact your dealer or your nearest
town or municipal office for its proper disposal.
*#1
$OM%OM$2OM Owner’s Manual
FOR UNITED KINGDOM:
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a molded 3-pin mains plug for your safety and convenience.
The plug contains a 5 amp fuse.
Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and
that it is approved by ASTA or BSI to BSI1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced.
If the fuse cover is lost, the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be obtained from your local Hammond Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME,
THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT-OFF PLUG IS INSERTED INTO
ANY 13 AMP SOCKET.
If a new plug is to be attached to the cord, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
IMPORTANT - The wires in this mains lead are coloured in accordance with the following code:
Blue:
Neutral
Brown:
Live
As the colours of the wires in the mains lead of this unit may not correspond with the coloured marking
identifying the terminals in your plug, proceed as follows.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with
the letter L or coloured RED.
Under no circumstances should either of these wires be connected to the earth terminal of the three-pin
plug, marked with the letter E or the Earth Symbol
.
To replace the fuse, open the fuse compartment with a screwdriver and replace the fuse and fuse cover.
Introduction
IMPORTANT - PLEASE READ
The Hammond B-3 is the most popular organ evermade, and its sound is legendary. We have
designed this model to be true and authentic to the exact vintage detail, as well as providing a
large variety of modern features that allow greater flexibility no matter the musical style you wish
to play. This Owner’s Manual is designed to explain the operating features of this Hammond
organ as simply and graphically as possible.
Because we want to make this manual, as well as the keyboard itself, as easy to understand as
possible, the explanations in this manual are grouped by subject matter, and not in the order in
which they necessarily appear in the display (the screen in the left of the keyboard front panel).
For example, all functions pertaining to Drawbars are grouped together, all Percussion features
are treated as a group, and so on.
Also, each feature is treated as an explanation unto itself, and does not require you to already
have prior working knowledge of some other feature. The explanations are presented such that, if
you follow the steps, will be identical to that shown in the manual at that stage of the explanation.
Do not be daunted by the number of steps required to perform each operation. Each step is
simple. Simply bear these things in mind:
1.
Read each step carefully.
2.
Don’t skip any of the steps.
3.
Don’t perform the steps out of sequence.
With these guidelines, you are well on your way to mastering all of the many sounds and features
of your Hammond organ.
*#1
$OM%OM$2OM Owner’s Manual
BATTERY BACK UP
This organ uses a battery-backed RAM to remember your changes to the Parameters.
When the battery voltage becomes low, the Display will show:
If you see these messages, you should immediately back up your parameter changes, if you have made
any. If there is no battery installed in the unit, or if the battery is compeletely dead, the Display will show:
After the above message is displayed, this organ will re-initialize itself, and the factory default settings
will be restored (except Presets, Leslie Cabinets and Cutsom Tone-Wheels). It is a good idea to periodically save your data to CompactFlash card.
CAUTION: Batteries should only be changed by your dealer or a qualified technician.
Introduction
Table Of Contents
IMPORTANT SAFETY INSTRUCTIONS ............................................ 2
IMPORTANT - PLEASE READ .......................................................... 4
BATTERY BACK UP ......................................................................... 5
Index .............................................................................................. 8
MAIN FEATURES ............................................................................ 9
HOW TO ASSEMBLE (B-3 mk2) ................................................... 10
Components .......................................................................................
Connect the Pedalboard ......................................................................
Attach the Leslie Speed Switch (USA only) .......................................
Attach the MAIN/ECHO Switch (optional) ............................................
Bench .................................................................................................
Manual Lid ..........................................................................................
Put on the Music Rack ........................................................................
10
11
11
12
12
13
13
HOW TO ASSEMBLE (B-3P mk2) ................................................. 14
Components .......................................................................................
Mount the Organ on the Stand ............................................................
Connect the Expression Pedal .............................................................
Connect the Pedalboard (optional) ......................................................
Attach the Leslie Speed Switch ...........................................................
Attach the MAIN/ECHO Switch (optional) ............................................
Open the Manual Lid ...........................................................................
Install the Music Rack .........................................................................
14
15
16
16
17
17
18
18
NAMES AND FUNCTIONS ............................................................. 20
Top View of the Organ ........................................................................
Volume Panel ......................................................................................
Control Panel ......................................................................................
Power Panel (B-3 mk2, C-3 mk2) .......................................................
Accessory Panel (B-3 mk2, C-3 mk2) ................................................
Accessory Panel (B-3P mk2) ..............................................................
Power Panel (B-3P mk2) ....................................................................
PEDALS ..............................................................................................
20
22
22
23
23
24
24
25
HOOK-UP ................................................. 27
BASIC HOOK-UP ........................................................................... 28
B-3 mk2, C-3 mk2 ...................................................................................... 28
B-3P mk2 .................................................................................................... 29
USING EFFECT LOOP ................................................................... 30
USING A MIDI SOUND MODULE .................................................. 30
USING TWO LESLIE SPEAKERS ................................................... 31
REINFORCING THE BASS ............................................................. 31
USING NO LESLIE SPEAKER ........................................................ 32
USING HEADPHONES ................................................................... 32
CONNECTING THE MIDI PEDALBOARD ........................................ 33
TURN ON AND PLAY ............................... 35
POWER ON ................................................................................... 36
How to power on ................................................................................ 36
Back-Up .............................................................................................. 36
Reset to the initial status ..................................................................... 36
USE OF PRESET KEYS .................................................................. 37
How to call the Preset ......................................................................... 37
ADDING EXPRESSION TO YOUR PLAYING ................................... 39
Expression Pedal ................................................................................ 39
Foot Switch ......................................................................................... 39
Motor Control Switch .......................................................................... 39
TRY MAKING YOUR OWN SOUND ................................................ 40
Select the Preset Key [B] ....................................................................
Pull out the B Drawbars ......................................................................
Add Percussion ..................................................................................
Add Effects .........................................................................................
VIBRATO AND CHORUS ............................................................................... 41
OVERDRIVE ................................................................................................. 41
LESLIE ......................................................................................................... 41
REVERB ....................................................................................................... 41
EQUALIZER .................................................................................................. 41
PEDAL SUSTAIN ................................................................................. 42
MANUAL BASS ................................................................................... 42
Recording Preset Keys ........................................................................ 43
Ex. Memorize to “2-D” ................................................................................. 43
SETTING UP ............................................ 45
SOUND ENGINE STRUCTURE ....................................................... 46
System structure of this Organ ........................................................... 46
HARMONIC DRAWBARS™ ........................................................... 48
Drawbars for the Swell/Great Manuals ................................................ 49
Relation between the Preset Keys and the Drawbars ................................... 49
WHITE DRAWBARS ..................................................................................... 49
BLACK DRAWBARS ..................................................................................... 49
BROWN DRAWBARS ................................................................................... 49
Drawbars for the Pedalboard ..............................................................
Drawbar Registration Patterns ............................................................
Modern Drawbar Registrations ...........................................................
Controlling the Registration while playing a Preset ..............................
49
50
51
52
PERCUSSION ................................................................................ 53
Notes .................................................................................................. 53
“Percussion does not sound!” ..................................................................... 53
DRAWBAR CANCEL ..................................................................................... 53
SINGLE TRIGGER ........................................................................................ 53
VIBRATO AND CHORUS ................................................................ 54
OVERDRIVE .................................................................................. 55
LESLIE .......................................................................................... 56
EQUALIZER, REVERB ................................................................... 57
Equalizer ............................................................................................. 57
Reverb ................................................................................................ 57
PRESETS ...................................................................................... 58
BANK and KEY .................................................................................... 58
Using Plural Presets at the Same Time ............................................... 59
Naming the BANK ............................................................................... 60
VOLUME ....................................................................................... 61
[MASTER VOLUME] Knob .................................................................. 61
Expression Pedal ................................................................................ 61
[VOLUME] Tablet ................................................................................ 61
Tone-Wheels and Multi-Contact Keys .......................................... 62
Ex. Select “2-G” .......................................................................................... 37
Play the Pedalboard ............................................................................ 38
*#1
40
40
40
41
$OM%OM$2OM Owner’s Manual
USING THE CONTROL PANEL ............... 63
SAVE THE SETUP ................................. 107
OPERATION CONTROL PANEL ...................................................... 64
PLAY MODE .................................................................................. 65
SAVE YOUR SETUP .................................................................... 108
How to read the Display ...................................................................... 65
Button operation in this mode ............................................................. 65
MENU MODE ................................................................................ 66
How to read the Display ...................................................................... 66
Button operation in this mode ............................................................. 66
FUNCTION MODE ......................................................................... 67
How to read the Display ...................................................................... 67
Button operation in this mode ............................................................. 67
Example: Increase the depth of Vibrato at [V-3]. ................................. 68
LOCK THE DISPLAY IN PLAY MODE ............................................. 70
SETTING THE PARAMETERS ................. 71
DRAWBAR .................................................................................... 72
Setting the SWELL and GREAT Manual ........................................................ 72
Setting the PEDAL Part ................................................................................ 73
PERCUSS (PERCUSSion) ............................................................. 74
TUNE ............................................................................................ 75
PRESET ........................................................................................ 76
BANK NAME ................................................................................................ 76
PRESET LOAD ............................................................................................. 76
See the current value (Temporary Scope) ........................................... 78
VIBRATO AND CHORUS ............................................................................... 78
PERCUSSION ............................................................................................... 79
LESLIE ......................................................................................................... 79
Other Knobs ................................................................................................. 79
TUBE AMP (TUBE pre-AMP) ........................................................ 80
Bias voltage and Nonlinear Distortion ................................................. 81
VIB&CHO (VIBrato and CHOrus) .................................................. 82
How to access the CF card slot ........................................................ 108
About the CF Card ............................................................................ 108
CF CARD YOU CAN USE ............................................................................ 108
CF CARD SLOT .......................................................................................... 108
THE CARD CAPACITY AND CONTENT TO BE SAVED ................................. 108
INITIALIZE THE CF CARD ........................................................... 109
SETUP PROCEDURES ................................................................. 110
How to read the Display ....................................................................
Save the SETUP ................................................................................
Change the SETUP name ..................................................................
Loading the SETUP ...........................................................................
How to delete the SETUP ..................................................................
110
110
111
112
112
FREQUENTLY ASKED QUESTIONS ..... 113
UTILIZING NEW FUNCTIONS & FEATURES ................................ 114
TROUBLESHOOTING .................................................................. 115
DAILY CARE AND MAINTENANCE ............................................... 116
APPENDIX ............................................. 117
MIDI IMPLEMENTATION CHART ................................................. 118
PARAMETERS ............................................................................. 119
Global Parameters ............................................................................
Preset Parameters .............................................................................
Leslie Parameters .............................................................................
System Parameters ...........................................................................
119
120
122
122
SPECIFICATIONS ........................................................................ 123
FACTORY PRESETS .................................................................... 124
SERVICE ..................................................................................... 127
Vibrato and Chorus of Hammond Organs ........................................... 83
LESLIE .......................................................................................... 84
CABINET NUMBERS .................................................................................... 84
LESLIE PARAMETERS .................................................................................. 84
Record the Cabinets ........................................................................... 87
EQ/REV (EQualizer/REVerb) ......................................................... 88
MANBS (MANual BaSs) ............................................................... 90
CONTROL ..................................................................................... 91
CUST. TW (CUSTom Tone-Wheels) ............................................... 92
Record the Custom Tone-Wheels ........................................................ 94
DEFAULT ....................................................................................... 95
SYSTEM ....................................................................................... 96
MIDI ......................................................... 97
ABOUT MIDI ................................................................................. 98
What is “MIDI”? .................................................................................. 98
MIDI terminals on this Organ .............................................................. 98
What the MIDI can do on your Organ .................................................. 98
MIDI STRUCTURE ....................................................................... 100
CONTROLLING EXTERNAL MIDI EQUIPMENT ............................ 101
EX. ZONE (EXternal ZONE) ......................................................... 102
IN THIS MANUAL:
NOTE:s and
appear frequently.
The NOTE: is a supplementary explanation.
The
are explanations of terms and applications.
Introduction
Index
A
L
Adjust Presets 40, 95, 108
Leakage Noise 72
Leslie 41, 56, 84
B
M
Bank 37
Bend 39
Chorale 56
Combination Presets 58
CompactFlash 108
Custom Tone-Wheels 92
Main 23, 24
Manual Bass 42, 90
Master Tune 75
Menu Mode 66
MIDI 98
MIDI Pedalboard 33
Motor Control Switch 39, 91
D
O
Default 95
Display Lock 70
Drawbars 40, 48, 72
Overdrive 41, 55, 80
C
E
Echo 23, 24
Effect Loop 30
Equalizer 88, 57
Expression Pedal 39, 91
External Zones 100, 102
F
Fold-Back 72
Foot Switch 39, 91
Footage 48
Function Mode 67
G
Great Keyboard 21
I
Initial Status 36
K
Key Mode 73
*#1
P
Pedal Sustain 42, 73
Pedalboard 25
Percussion 74, 40, 53, 74
Play Mode 65
Preset 76
Preset Key 40
R
Registration 40, 50, 52
Reverb 41, 57, 89
Rotary Channel 56
S
Setup 110
Short Cut 79
Spring Reverb 91
Stationary Channel 56
Swell Keyboard 21
T
Temporary Scope 78
Tone-Wheels 72
Transpose 75
Tremolo 56, 82
$OM%OM$2OM Owner’s Manual
Tube Amp 55, 80
V
Velocity 101, 104
Version 96
Vibrato 82
Vibrato and Chorus 41, 54
Volume 61
MAIN FEATURES
9
‹MULTI-CONTACT MANUALS
The keyboards used in this organ have been totally redesigned and 100% faithfully replicates the “Direct Analog Keying
System” used on the original B-3.
‹TONE-WHEELS REBORN THROUGH DIGITAL TECHNOLOGY
The “Digital Tone-Wheel System” replicates the Tone-Wheel wave-forms created by the mechanical system of the
original B-3. The 96 wave-forms are always in oscillation just as in the original.
‹ALL CONTROLS EXACTLY AS ON THE ORIGINAL
All the controls from the Panel Switches to the Preset Keys have been faithfully replicated. This organ can be played
with the same technique as the original B-3.
‹TUBE PRE-AMPLIFIER
A pre-amp circuit using a 12AU7 tube is built in, and unique tube over-drive sounds are obtained. The bias-voltageadjustment function enables not only general clip distortion but also nonlinear distortion.
‹DIGITAL LESLIE/VIBRATO
The scanner vibrato and Leslie speaker are replicated via a DSP effects section. The Vibrato & Chorus effects are the
same as on the original B-3. The built-in Leslie gives the familiar Leslie sound when no actual Leslie speaker is available
or when practicing with headphones.
‹EQUALIZER AND TONE CONTROL
A 3-band equalizer and tone-control are now built in. The equalizer can make fine or coarse tonal adjustments to the
bass, treble, and mid frequency ranges. The tone-control simulates the unique circuit built in on the vintage B-3 pre-amp
to obtain a gently-cut treble.
‹MIDI MASTER KEYBOARD
3 external zones are available on each manual and pedalboard to enable this organ to be used as a master keyboard. A
MIDI pedalboard can also be used instead of the traditional pedalboard.
‹CompactFlash™ CARD
You can use a CompactFlash Card to save various Parameter files.
Introduction
HOW TO ASSEMBLE (B-3 mk2)
10
Components
Organ
Music Rack
Key
CompactFlash Card
(inserted into the organ)
Pedalboard
Hexagonal Wrench
AC Power Cord
Bench
USA Only
Leslie Speed Switch
Wire Clamp
Tapping Screws
*#1
$OM%OM$2OMOwner’s Manual
11
Connect the Pedalboard
Attach the Leslie Speed Switch
(USA only)
HA<O>
HA<O>
1. Place the Pedalboard on the floor in front of the organ.
2. Take the Pedal Cable out of the organ and insert the plug
into the connector on the Pedalboard.
3. Hold the plug with the “Retention Hook” and lock it on
by turning the screw knob.
4. Slide and push in the Pedalboard beneath the organ until
it stops.
1. Locate a #2 Phillips Screw Driver.
2. Position the Leslie Speed Switch on the front left of the
Great Manual. The distance it from the left sideboard must
be 150 mm (6 in.) to allow for mounting the Main/Echo
Switch.
3. Attach the switch from the bottom with the tapping screws
supplied.
4. Insert the plug of the Leslie speed switch into the LESLIE
SWITCH Jack on the Volume Panel.
5. Affix the wire clamp on the bottom of the organ and affix
the cable.
Introduction
12
Attach the MAIN/ECHO Switch Bench
The space underneath the top board of the bench is provided for
(optional)
This switch is for selecting either of the Leslie speakers if 2 are
connected.
1. Locate a #2 Phillips screw driver.
2. Position the Main/Echo Switch to the front left of the Great
Manual.
3. Attach with the 4mm tapping screws from underneath.
4. Insert the plug of the Main/Echo Switch cable into the
MAIN/ECHO Jack on the Volume Panel.
storing scores, music rack, etc.
CAUTION
Be careful not to pinch your fingers, by the folding metal arms
when you close the lid.
Do not adjust the position of the bench while sitting. Avoid the
risk of pinching your fingers between the lid and the box.
ATTENTION
Don’t tilt the bench when moving it to avoid books etc. from
dropping out of the box.
Do not put in anything taller than 7 cm (2.7 in.) into the bench.
The lid will not close and may damage the contents.
*#1
$OM%OM$2OMOwner’s Manual
13
Manual Lid
Put on the Music Rack
Insert the Music Rack into the rail whenever necessary.
1. When you open the lid, hold and lift the front gently with
both hands and fold it.
2. When you close the lid, hold the front of the folded lid
with both hands and put down gently to close.
ATTENTION
Be careful not to pinch your fingers when you open or close the
lid. If the player is a small child, be sure to help him/her to open
or close the lid.
ATTENTION
Do not put excessive pressure on the music rack.
Be sure to close and lock the lid before you move/carry the organ
and avoid any risk of injury.
Do not leave the score or music rack on the manual when you
close the lid.
You can lock the key lid.
[B-3 mk2] The key hole is on the right side board.
[C-3 mk2] The key hole is on the front center.
Introduction
HOW TO ASSEMBLE (B-3P mk2)
14
Components
Organ (closed view)
Music Rack (inside of the lid)
CompactFlash Card
(inserted into the organ)
Stand
Hexagonal Wrench
AC Power Cord
Leslie Speed Switch, Spacer
Expression Pedal
Wire Clamp
*#1
$OM%OM$2OMOwner’s Manual
15
Mount the Organ on the Stand
CAUTION
The organ must be mounted on the stand by two persons using both hands.
1. Remove the Knob Bolts on both sides of the organ.
2. Unfold the stand and place it in the upright position.
3. The stand must be placed flat on the floor. Turn the adjusters, if necessary, to level the stand.
4. With a helper, lift the organ gripping the side handles, then carefully
mount it on the stand.
CAUTION
Be careful not to get your fingers pinched! This could occur if they are
caught between the organ and the stand.
5. After mounting the organ on the stand, insert the Knob Bolts through
the screw holes on both sides of the stand and also on the organ, and
tighten them securely.
Insert the Knob Bolts straight through horizontally. If the knobs are askew, they
may damage the screw threads on the stand and/or the organ.
Introduction
16
Connect the Expression Pedal C o n n e c t t h e Pe d a l b o a r d
(optional)
Insert the plug the cable from the Expression Pedal to the
EXP.PEDAL connector on the power panel (on the bottom of the organ), matching the direction, then tighten it
by turning the ring on it.
1. Insert the cable of the Pedalboard PK-25PR to the connector of the Pedalboard and the PEDALBOARD connector on the power panel (on the bottom of the organ),
matching the direction, and secure it by turning the ring
on the plug clockwise.
2. Insert the plug of the cable from the Expression Pedal to
the EXP.PEDAL connector on the power panel (on the
bottom of the organ), matching the direction, then fix it
by turning the ring on the plug clockwise.
*#1
$OM%OM$2OMOwner’s Manual
17
Attach the Leslie Speed Switch Attach the MAIN/ECHO Switch
(optional)
1. Remove the 2 inside knob screws on the front left of the
Great Manual.
1. Remove the 2 outside knob screws on the front left of the
Great Manual.
2. Put the spacer on the plate of the Leslie Speed Switch.
2. Put the spacer on the plate of the Main/Echo switch.
3. Attach the Leslie Speed Switch on the organ with the knob
screws.
4. Insert the plug of the Leslie Speed Switch cable to the
LESLIE SWITCH jack on the volume panel.
3. Attach the Main/Echo switch on the organ with the knob
screws.
4. Insert the plug of the Main/Echo switch cable to the
MAIN/ECHO jack on the volume panel.
Introduction
18
Open the Manual Lid
Install the Music Rack
The Music Rack is inside the back of the manual lid.
1. Turn the knob screw inside the manual lid counter-clockwise and remove the stopper.
2. Slide the music rack into the music rail.
1. To open the manual lid, release the lock on both sides,
then gently lift it holding the knobs on both sides bwith
both hands. When the lid opened about 135 degrees, slide
it back and off the hinge.
2. To close, hook the lid on the hinge and put it upright to 90
degrees. Hold the knobs with both hands and put it down
gently. When the lid is closed, lock it again.
ATTENTION
Do not put any excessive pressure on the music rack.
ATTENTION
Do the steps above with care, and do not pinch your fingers. If a
small child plays the organ, an adult must help him/her open or
close the lid.
When it is necessary to move the organ, be sure to do it with the
lid closed and locked.
Do not close the lid while music sheets or rack are still on the
manual.
*#1
$OM%OM$2OMOwner’s Manual
19
Introduction
NAMES AND FUNCTIONS
20
Top View of the Organ
4
5
6
8
7
9
17
18
19
20
10
21
and Pedal Drawbars.
‹SWITCH PLATE
1.
POWER Switch
This switch turns the power on and off.
Even when the POWER switch is turned off, electricity
is still flowing to the instrument at a minimum level. When
you are not using the instrument for an extended time,
make sure you unplug the power cord from the wall AC
outlet.
2.
MOTOR CONTROL Switch
This is for changing the pitch while playing. If you move it back,
the pitch rises. If forward, it falls.
3.
PILOT LAMP
Lights while the power is on.
‹LEFT TABLETS
4.
VOLUME Tablet
This is for switching the volume; NORMAL or SOFT.
5.
VIBRATO SWELL Tablet
This is for switching the vibrato and chorus on/off on the Swell
Manual Drawbars.
VIBRATO GREAT Tablet
This is for switching the vibrato & chorus on/off on the Great
*#1
VIBRATO & CHORUS MODE Knob
This is for switching the depth of vibrato and the chorus effects.
‹DRAWBARS
CAUTION
6.
7.
8.
SWELL(Upper) A< Drawbars
These are for adjusting the harmonics of the Swell(Upper)
Manual, when the Preset Key [A<] of the Swell Manual is selected.
9.
SWELL(Upper) B Drawbars
These are for adjusting the harmonics of the Swell(Upper)
Manual, when the Preset Key [B] of the Swell Manual is selected.
10. PEDAL Drawbars
These are for adjusting the harmonics of the Pedalboard.
11. GREAT(Lower) A< Drawbars
These are for adjusting the harmonics of the Great(Lower)
Manual, when the Preset Key [A<] of the Great Manual is selected.
12. GREAT(Lower) B Drawbars
These are for adjusting the harmonics of the Great(Lower)
Manual, when the Preset Key [B] of the Great Manual is selected.
$OM%OM$2OMOwner’s Manual
21
2
11
12
3
1
13 14 15 16
‹RIGHT TABLETS
‹MANUALS
13. PERCUSSION Tablet
This is for switching the Percussion on/off.
17. SWELL(Upper) Preset Keys
These are for selecting the Presets of the Swell(Upper) Manual.
14. PERCUSSION VOLUME Tablet
This is for switching the volume of Percussion: NORMAL/SOFT.
18. SWELL(Upper) Manual
This is a manual with 61 notes, multi-contacts (for Drawbars &
Percussion) with contacts (for MIDI OUT).
15. PERCUSSION DECAY Tablet
This is for switching the decay time of Percussion: FAST/SLOW.
16. PERCUSSION HARMONIC SELECTOR Tablet
This is for switching the pitch of Percussion: THIRD harmonics
/ SECOND harmonics.
19. GREAT(Lower) Preset Keys
These are for selecting the Presets of the Great(Lower) Manual.
20. GREAT(Lower) Manual
This is a manual with 61 notes, multi-contacts (for Drawbars)
with contacts (for MIDI OUT).
‹LESLIE SWITCH
21. LESLIE SPEED SWITCH
This is for switching the speed of the external Leslie speaker or
built-in Leslie effects.
Introduction
22
Volume Panel
25. MASTER VOLUME Knob
This is for controlling the total volume of this organ.
22
26
24
23
25
28
27
26. BASS Knob
This is for increasing/decreasing the volume of the Bass frequencies.
29
22. MAIN/ECHO Jack
This is for connecting the Main/Echo Switch MES-1.
23. HEADPHONE Jack
This is for connecting Headphones. The external Leslie speaker
is turned off, when a plug is inserted to this jack.
27. TREBLE Knob
This is for increasing/decreasing the volume of the Treble frequencies.
28. REVERB Knob
This is for adjusting the depth of the Reverb effects.
29. OVERDRIVE Knob
This is for adjusting the depth of the Overdrive effects.
24. LESLIE SWITCH Jack
This is for connecting the Leslie Speed Switch (provided).
Control Panel
Contained in the drawer on the bottom right of the manual. [B-3 mk2 and C-3 mk2]
Located inside the lid on the left-hand-side front panel. [B-3P mk2]
30
31
32
34
33
35
36
30. Display
Various information is displayed here.
31. PAGE Button
Used to scroll through the various pages of controls and parameters.
32. PARAM Button
This is used for selecting the parameter item to edit, also to select items #1 and #2 on the basic edit pages.
33. VALUE Button
This is used to increase or decrease values, also to select items
#3 and #4 on the basic edit pages.
*#1
34. MENU/EXIT Button
This is for calling the MENU mode, A for exiting from various
function modes, and jump to function modes.
35. RECORD Button
This is for recording Presets, also for shifting values or items.
36. PLAY Button
This is for jumping to the basic Play mode. It is also for using
the temporary scope function, or for changing the registrations
while the Preset Keys from [C<] to [A] are selected.
$OM%OM$2OMOwner’s Manual
23
Accessory Panel (B-3 mk2, C-3 mk2)
‹EFFECT LOOP
37
40. SEND Jack
This is a post-internal effects patch-out point.
38
If a plug is inserted to this jack, signals inside the organ are cut
off. (Rating Output Level: 1.23V +4dBm, Output Impedance:
600Ω)
40 41 39
42
43
41. RETURN Jack
This is a post-internal effects patch-in point.
This jack is used also as the input terminal to the rotary channel
from an external sound source. (Rating Input Level: 1.23V
+4dBm, Input Impedance: 10kΩ)
‹SOUND INPUT TERMINAL
37. LINE IN Jack
This is the terminal for connecting an external sound module or
a CD player. The signals input to this jack are output to the LINE
OUT jack, headphone jack, the stationary channel of each Leslie.
(Rating Input Level: 1.23V +4dBm, Input Impedance: 5kΩ)
‹MIDI TERMINAL
‹SOUND OUTPUT TERMINAL
38. LINE OUT Jack
The main output terminals, post internal effects (includes the
built-in Leslie effect).
42. MIDI OUT Jack
This is for sending playing information to external MIDI equipment such as a Synthesizer or a Sound Module.
43. MIDI PEDAL IN Jack
This is the input for a MIDI Pedalboard.
Use both L and R, if the connected mixer or monitor speaker is
stereo, and use only L, if monaural.
When the Leslie speaker is connected, the built-in Leslie effect
appars on the L output only.
39. PEDAL OUT Jack
This is an independent output terminal for the Pedal part.
Power Panel (B-3 mk2, C-3 mk2)
42. AC Inlet
Connects the A.C. Power Cable.
CAUTION
This organ shall be connected to a MAINS socket outlet with a protective earth (ground) connection.
‹LESLIE SOCKETS
44
45 46
45. MAIN
Connect the first Leslie speaker here. If the Main/Echo switch (optional) is connected to the MAIN/ECHO jack on the Volume Panel(#22), the sound is not
output unless you set the switch at the MAIN position.
46. ECHO
Connect the second Leslie speaker to this. Sound is sent here, if you set the
optional Main/Echo switch to the echo position when the Main/Echo switch is
connected to this organ.
Introduction
24
Accessory Panel (B-3P mk2)
48
47
50 51 49
52
When a plug is inserted to this jack, signals inside the organ are
cut off. (Rating Output Level: 1.23V +4dBm, Output Impedance: 600Ω)
54
53
55
51. RETURN Jack
This is a post-internal effects patch-in point.
This jack is used also as the input terminal to the rotary channel
from an external sound engine. (Rating Input Level: 1.23V
+4dBm, Input Impedance: 10kΩ)
‹MIDI TERMINAL
‹SOUND INPUT TERMINAL
47. LINE IN Jack
These jacks are for connecting an external sound module or a
CD player. The signals input to this jack are output to the LINE
OUT jack, and headphone jack, the stationary channel of a soequipped Leslie Spaker. (Rating Input Level: 1.23V +4dBm, Input Impedance: 5kΩ)
‹SOUND OUTPUT TERMINAL
48. LINE OUT Jack
These jacks are a stereo main out for the organ post-internal
effects.
Use both L and R, if the connected mixer or monitor speaker is
stereo, and use only L, if monaural.
When a Leslie speaker is connected, the built-in Leslie effect
appears only on the L jack.
52. MIDI OUT Jack
This is for sending MIDI information to external MIDI equipment such as a Synthesizer or Sound Module.
53. MIDI PEDAL IN Jack
This is the input terminal for a MIDI Pedalboard.
‹LESLIE SOCKETS
54. MAIN
Connect the first Leslie speaker to this socket. If the Main/Echo
switch (optional) is connected to the MAIN/ECHO jack on the
Volume Panel (#22), Sound is not passed unless you set the switch
at the MAIN position.
55. ECHO
Connect the second Leslie speaker to this socket. Sound is not
passed unless you set the switch to the ECHO position when the
Main/Echo switch (optional) is connected to this organ.
49. PEDAL OUT Jack
This is an independent output terminal for the Pedal part.
‹EFFECT LOOP
50. SEND Jack
This is a post-internal effects patch-out point.
Power Panel (B-3P mk2)
If no expression pedal is connected, the volume is set to
maximum, as if the pedal were fully depressed.
‹AC INLET
56
56. AC INLET
Connects the A.C. Power Cable.
CAUTION
This organ shall be connected to a MAINS
socket outlet with a protective earth (ground)
connection.
58
57
58. PEDALBOARD Connector
Connect the Pedalboard PK-25PR (optional) here.
‹PEDAL CONNECTORS
57. EXP. PEDAL Connector
Connect the Expression Pedal (provided) here.
*#1
$OM%OM$2OMOwner’s Manual
25
PEDALS
59. EXPRESSION Pedal
This is for changing the total volume of the organ.
59
B -3 mk2
The Foot Switch is attached on the bottom left.
B -3P mk2
60. Pedalboard
25 notes. Radial flat type, non-velocity keyboard.
61. Foot Rest
Rest your feet when you are not playing the Pedalboard.
60
61
Introduction
26
*#1
$OM%OM$2OMOwner’s Manual
27
HOOK-UP
*#1
$OM%OM$2OMOwner’s Manual
BASIC HOOK-UP
28
See the figure below for connection.
This organ has no built-in speaker or amplifier. Before you connect a Leslie Speaker to the organ, be sure to turn OFF the power
of the organ and the external equipment, if any is connected.
The Leslie Speaker is connected to the LESLIE/MAIN jack on
the organ using the exclusive 11-pin Leslie Cable attached to the
speaker or the LC-11-7M (optional).
Plug in the Leslie Cable to the jack, correctly matching the notches.
NOTE:
Non-11-pin Leslie Speakers can also be connected to
the organ using a special adaptor kit. Ask your
Hammond Organ / Leslie dealer for details.
B-3 mk2, C-3 mk2
AC IN
*#1
MAIN
ECHO
HOLES FOR CABLES (C-3 mk2)
Drilled holes are located on the side of the cabinet of the C-3 mk2
for your convenience.
$OM%OM$2OMOwner’s Manual
29
B-3P mk2
Fasten the cables using hook-and-loop fastners.
Hook-Up
USING EFFECT LOOP
30
External effects may be used while a Leslie Speaker is connected
to the organ using the Effect Loop.
The effects unit should have the same input/output gain and corresponding with the rating level of +4dBm.
NOTE:
NOTE:
The Effect Loop is inserted between the built-in Effect
(Leslie, Reverb, etc.) and the Master Volume.
If using the LINE OUT jack and the HEADPHONE jack,
simultaneously the Effect Loop will only function on the
R (right) side.
USING A MIDI SOUND MODULE
Each Manual and the Pedalboard on this organ has 3 External
Zones for controlling an external MIDI sound module. When
connected to the LINE IN jacks, the external MIDI sound module output is sent to the stationary channel of the Leslie terminal
(on a so-equipped Leslie), the LINE OUT jack and the headphone
jack.
NOTE:
Adjust the volume of the equipment connected to the
LINE IN jack on the external equipment itself.
*#1
$OM%OM$2OMOwner’s Manual
USING TWO LESLIE SPEAKERS
Two Leslie Speakers may be connected to this organ.
Connect the first Leslie Speaker to the MAIN socket and the second to the ECHO socket. The organ sounds are usually produced
from both Leslie Speakers. If you connect the MAIN/ECHO
switch, you can select which Leslie sounds while you are playing.
31
The sound that is input from LINE IN jack will be sent out to
both Leslie speakers regardless of the position of the MAIN/ECHO
switch.
REINFORCING THE BASS
To reinforce the bass, or if you do not wish to have the Pedals
speak through the Leslie, you can send the Pedal part directly to
a bass amp or PA system using the independent PEDAL OUT
jack. Set your PEDAL OUT preference by the OUTPUT param-
eter of the OUTPUT on the PEDAL PART page in the SYSTEM
function mode. (P. 96 #1)
Hook-Up
USING NO LESLIE SPEAKER
32
If no Leslie Speaker is available, you can use the built-in Leslie
Effect by means of the LINE OUT jack.
If the Leslie Speaker and the LINE OUT jack are used together,
the built-in Leslie Effect is heard only on the L channel.
You may also use a traditional keyboard amp or PA system.
USING HEADPHONES
You can practice silently by connecting the stereo headphones to
the HEADPHONE jack of this organ.
When the plug is inserted to the HEADPHONE jack, the Leslie
Speaker is turned off, and the built-in digital Leslie Effect comes
online in the headphones.
*#1
ATTENTION
Hold the moulded part of the plug of the cord when you connect
or disconnect it to avoid the risk of breaking the cable.
Do not use excessive volume with headphones, due to risk hearing damage.
$OM%OM$2OMOwner’s Manual
CONNECTING THE MIDI PEDALBOARD
You may connect a MIDI Pedalboard, instead of the traditional
Pedalboard.
All the note information received at the MIDI PEDAL IN jack is
output as the Pedal Part, regardless of the MIDI channel.
The following MIDI pedalboards connectable to this organ are
also available from us as optional accessories:
XPK-100 (13 notes)
XPK-200 (20 notes)
NOTE:
NOTE:
33
You can attach an expression pedal (provided with the
B-3P mk2) on the XPK-200.
You can not use the functions of the XPK-100 such as
transpose, control, etc., if the XPK-100 is connected.
Hook-Up
34
*#1
$OM%OM$2OMOwner’s Manual
35
TURN ON AND PLAY
*#1
$OM%OM$2OMOwner’s Manual
POWER ON
36
How to power on
After connecting your organ to the power outlet, please follow this procedure before switching on
the power. To avoid possible damage to your speakers, please follow this procedure exactly.
1. Set the [MASTER VOLUME] Knob at minimum.
2. Switch on the power of any external effects devices.
3. Turn on the [POWER] switch of the organ. The pilot lamp will light up and the PLAY
mode (fig.) is displayed, following the title. The Leslie Speaker is automatically turned on
simultaneously, if connected.
™ It takes a few seconds to reach play mode, because of the circuit-protection
devices.
™ The tubes require 10 to 20 seconds to warm up.
4. Turn on the power of the amplifier etc., if any connected to the LINE OUT.
5. Holding down a key, adjust the [MASTER VOLUME] by turning the Knob.
™ The Preset Key [B] does not produce sound when intially first turned on. Draw
the B Drawbars, or press either of the Preset Keys [C<] - [A] to start.
6. Adjust the volume of the amplifiers etc.
™ Reverse the above steps when you switch off the power. (Switch off the power
of the amplifiers etc. first.)
Back-Up
This organ memorizes the settings of the parameters immediately before it is switched off. The organ
will start with these settings when it is switched on again.
Reset to the initial status
To reset the organ to the initial default setting:
1. Switch off the power of the organ.
2. Holding the [RECORD] button, switch on the power.
3. Keep pressing the [RECORD] button until “Loading Default...” appears on the
display.
4. When the reset is complete, PLAY mode appears on the display. (Completed)
*#1
$OM%OM$2OMOwner’s Manual
USE OF PRESET KEYS
The registrations (settings) of the Drawbars and other parameters may be recorded to the Preset Keys on the lefthand side of each manual.
37
The 4 Banks are loaded with a default library of Presets
allowing you to play your organ immediately.
There are 5 Banks with 11 Presets in each.
The chart on the left outlines the Bank/Preset structure.
The “Bank” is common for the entire organ, but the Preset Keys for the Swell and
Great are independent of each other and are selected separately.
Let’s call this in the example below.
NOTE: The Preset Key [C] produces no sound but releases the Preset Key
previously selected. It is called “cancel”.
How to call the Preset
Ex. Select “2-G”
1. Select the BANK
Select Bank 2 using [PARAM] Buttons in the PLAY mode.
2. Select the KEY
Press the Preset Key [G].
The [G] key remains depressed and the contents of the Preset Key are called.
Try calling various Presets. See the Appendix “Factory Presets” (P. 124) at the
back of this manual for details of the contents of each Preset.
NOTE: Only the Drawbar registrations were able to be called on the original B-3. The factory settings of this new organ are the same as the
factory settings of the original. You can change to call other parameters by the Preset Keys. See the “PRESET” section for details. (P. 76)
Turn On And Play
38
Play the Pedalboard
The Pedal tones are controlled by the Pedal Drawbars which are in the center of
the Drawbar row. Pull out the 16' Drawbar as shown at left to the full length. Play
the Pedalboard. The Drawbar to the right of the 16' is the 8'. Pull that Drawbar out
and play the Pedalboard (Explanations of the Drawbars and the “foot” names are
included in the next section “Creating the Settings”).
The Pedal Part settings were not called at the Preset Keys on the original B-3. The
factory setting of this organ is the same way.
NOTE: You can change to record/call out the Pedal Part settings at the
Great Preset Keys. For details, see the “Preset” section. (P. 76)
*#1
$OM%OM$2OMOwner’s Manual
ADDING EXPRESSION TO YOUR PLAYING
39
Expression Pedal
Unlike the piano, the organ does not get louder, the harder you play the keys. The
organ’s volume is controlled by using the expression pedal.
As you depress the pedal forward, the volume rises, and lowers when you return it.
NOTE: You can adjust the curve of the expression pedal. (P. 91)
Foot Switch
The Foot Switch, on the left side of the Expression Pedal can be programmed for
various functions. “Leslie Chorale / Tremolo - Alternate” is the factory default.
Every time you depress the Foot Switch, the Leslie changes speed.
NOTE: You can change the Foot Switch assignment. (P. 91)
Motor Control Switch
You can bend the pitch if you operate this switch while playing, same as the START
and RUN switches on the original B-3. While the toggle is at the UP position, the
pitch gradually goes up, and, while at the DOWN position, the pitch gradually
goes down to 2 octaves lower and also the volume gradually gets smaller.
NOTE: You can change the time of the pitch bend. (P. 91)
START AND RUN
The original B-3 required a two-step procedure to power up. You would first “start”
the motors by holding the spring-loaded left switch, and after a few seconds, you
would release the “start” switch and turn on the “run” switch. Organists discoverd
that if you engaged the start switch while the organ was running, it would give a
distinctive “pitch bend” to the organ tone. This organ, being totally digital only
needs the power switch, but to remain authentic, the motor control switch is included, and the “pitch bend” effect is duplicated.
Turn On And Play
TRY MAKING YOUR OWN SOUND
40
You will be able to produce your own sound by using the exclusive features of your
HAMMOND ORGAN, such as Drawbars, Percussion, Vibrato/Chorus, Overdrive,
and the Leslie effects. Let’s go through the first steps:
Select the Preset Key [B]
Select the Preset Key [B] first.
The Presets Key [A<] and [B] are special Presets called “Adjust Presets”, directly connected with A< Drawbars and B Drawbars respectively. That means the Drawbar registrations on the panel and the internal registration, each position of tablets or knobs and internal values
correspond with each other.
Selecting these keys are helpful when you create a new registration or
when you want to manually operate the Drawbars while playing.
NOTE: You can initialize the contents to the default setting. (P.
95)
Pull out the B Drawbars
Pull out the B Drawbars on the left-hand side to any length, while
playing the Swell(Upper) manual.
The tones vary corresponding to how far the Drawbars are “Pulled”.
The Drawbars create the fundamental tones of this organ.
The volume increases as each Drawbar is pulled out to its full length.
And decreases as it is pushed back in. The tones of the Drawbars gradually get higher in frequency from left to right.
The most popular patterns or registrations are (1) to pull out only all
the three left side Drawbars to the full, (2) to pull the far-left and only
the white bars to the full, or (3) to pull all the bars.
NOTE: You can change the characteristics of the Drawbars. (P.
72)
NOTE: The present registration is shown on the “Play” mode
display. (P. 65)
Add Percussion
The “Percussion” referred to here is not a percussion instrument itself,
but an extra voice which adds a clear-cut “attack” to the organ sound.
You can add this “attack” to mix with the Drawbar sound when you
want.
Percussion sounds only when using Swell Manual preset [B]. This is
the same as on the vintage B-3.
Switch the percussion tab to “On”, the percussion voice will speak. An
octave up(second) or a twelfth up(third) by using the [PERCUSSION
HARMONIC SELECTOR] tab. Switch the decay time by [PERCUSSION DECAY] and the volume by [PERCUSSION VOLUME].
NOTE: The volume etc. of Percussion can be finely set. (P. 74)
*#1
$OM%OM$2OMOwner’s Manual
41
Add Effects
VIBRATO AND CHORUS
“Vibrato and Chorus” slightly changes the Drawbar pitch and adds warmth to the sound.
[SWELL] Tablet, [GREAT] Tablet
Switches the Vibrato/Chorus on and off for each manual.
[VIBRATO AND CHORUS MODE] Knob
Controls the Vibrato and Chorus Depth.
The degree of depth corresponds with the number. “V” adds Vibrato sound by changing the pitch,
“C” adds the original shimmering Hammond chorus.
NOTE: You can fine-adjust the speed etc. of the Vibrato&Chorus. (P. 82)
OVERDRIVE
Adds tube-based distortion to the sound.
[OVERDRIVE] Knob
Controls the distortion amount. Full left is “clean”. The distortion effect increase as you rotate the
knob clockwise.
NOTE: Overdrive distortion can be fine-set. (P. 80)
LESLIE
The Leslie speaker uses a rotating treble horn and a woofer firing into a rotating drum to give the
organ a “3-D” sound, with motion and lively dynamics. It is the traditional partner of the Hammond
Organ.
LESLIE SPEED Switch
This is for switching the mode of the Leslie Speaker or the built-in Leslie Effect.
At CHORALE the rotor turns slowly, at TREMOLO fast. It stops at STOP.
NOTE: You can fine-adjust the rotation speed etc. of the internal LESLIE Effect. (P. 84)
REVERB
The reverb effect simulates performing in a concert-hall.
[REVERB] Knob
Controls the depth of the Reverb Effect. At full left the Reverb Effect is off. The effect deepens as
you rotate the knob.
NOTE: You can fine-control time etc. of Reverb. (P. 88)
EQUALIZER
Controls the overall tone of the organ.
[BASS] Knob
Increases or decreases the emphasis of the Bass range of sound.
[TREBLE] Knob
Increases or decreases the emphasis of the Treble range of sound.
NOTE: Each BASS, TREBLE knob can be assigned to a different band respectively. (P. 88
#6, 7)
Turn On And Play
42
PEDAL SUSTAIN
The Pedal Part sound can be set to smoothly decay after the key is released. This is
called “PEDAL SUSTAIN”.
To use this “Pedal Sustain” function, refer to the control panel.
1. Press the [PLAY] button, and display “P. SUS” on the bottom right of the
display.
2. Switch ON the PEDAL SUSTAIN using the [VALUE] button.
2
1
If you release your foot off the Pedalboard (or your finger from the Great Manual, if
you are using the Manual Bass function, as explained later in this manual), the Pedal
Part sound smoothly decays.
NOTE: You can change the decay time of the Pedal Sustain. (P. 73 #8)
MANUAL BASS
You can play Bass using the lowest keys of the Great manual. This is called “Manual
Bass”.
To use the Manual Bass function, refer to the control panel.
1. Press the [PLAY] button, and display “MANBS” on the bottom right.
2. Switch ON the MANUAL BASS using the [VALUE] button.
2
When playing the Great manual, the lowest note (or chord) played will be sounded by
the Pedal voice.
1
The factory default Manual Bass range is set to “B” of the second octave.
NOTE: You can move the upper limit of the Manual Bass. (P. 90)
NOTE: You can choose sounding polyphonic (POLY) or lowest note (MONO).
(P. 73 #9)
*#1
$OM%OM$2OMOwner’s Manual
43
Recording Preset Keys
You can record your Drawbar registrations in the Preset Keys. You can also freely change the
preset data loaded as the factory default.
To record Drawbar registrations in the Preset Keys, refer to the control panel.
Ex. Memorize to “2-D”
1
1. Go to the PLAY mode.
Press the [PLAY] button to go to the PLAY mode.
2
2. Go to the Record mode.
Press the [RECORD] button and go to that mode.
3
3. Designate the Bank.
Press the [PARAM] button and select the Bank to record. For this example select
“2”.
*to be continued to the next page.
Turn On And Play
44
4
4. Select the Part to record.
Press the [PAGE] button and select either SWELL or GREAT to record the Preset.
For this example select “GREAT”.
NOTE: You can select the part to record by the Preset Key, as well.
5
5. Select the Preset Key.
Select the Preset Key ([C<] - [A]) to record. For this example, Press [D].
6. Commit the Preset.
6
Press [4] OK. The Preset is recorded and the following message appears on the
display for a few seconds.
Recording PRESET...
NOTE: The recorded Preset data is retained when if the power is switched
off.
NOTE: When recording the presets, not only are the Drawbar registrations
saved, but also various parameters. For details, see the PRESET
section. (P. 76)
*#1
$OM%OM$2OMOwner’s Manual
45
SETTING UP
*#1
$OM%OM$2OMOwner’s Manual
SOUND ENGINE STRUCTURE
46
System structure of this Organ
*#1
$OM%OM$2OMOwner’s Manual
47
See the illustrated System Structure of your organ on the left page.
TONE-WHEELS
The sound source or “engine” of Hammond Organ is the Virtual Tone-wheel. Generator.
As on the original B-3, each of the 96 Virtual Tone-wheels are oscillating at a different
pitch. There are NO moving parts inside this organ.
KEYS
The tones of the 96 Virtual Tone-wheels are switched at the keyboard with the “Direct
Analog Keying System” exactly as on the original B-3. There are 9 contacts at each key
responding to each of the 9 Drawbars. When you press a key, the contacts are made to play
the corresponding Drawbars to the pitch of the key depressed.
TONE-WHEEL SET
The Tone-wheel Sets are divided into the
Manuals and the Pedal Part. This is to give
the Pedal Part the Decay (= the sound gradually fading out while pressing the key) or Sustain Effect. (= the sound gradually fading out
after the key is released).
DRAWBARS
The Drawbars represent simple harmonics. Each bar adjusts the value of each harmonic.
The combinations of different harmonics create a more complex sound.
PERCUSSION
The Percussion adds a voice with clear attack to the Swell manual. This effect is an essential part of the Hammond Sound.
HARMONICS
Harmonic is a pitch of a different ratio to a certain pitch; for example, the one octave higher
C to the middle C. The more Harmonics, the
brighter and richer sound is obtained.
VIBRATO AND CHORUS
The classic Hammond “Chorus-Vibrato” gives depth and richness to the organ sound by
slightly varying the pitch (Vibrato) or doubling the voice, just slightly out of tune (Chorus). This effect is a hallmark of the vintage B-3 sound.
NOTE: On this organ the mechanical scanner of the original B-3 is simulated, with no moving
parts.
TUBE PRE-AMPLIFIER
A real tube in the pre-amplifier gives this organ the “vintage” sound. By changing the
amount of the drive, you can obtain various tube sound from “clean” (no clipping), to the
hard-distorted fuzzy and raspy “overdrive” popular in rock music.
The Pedal Part is designed not to pass through the tube pre-amp in order to obtain a clear
Bass-Pedal tone.
EFFECTS
The built-in Effects are as follows: an Equalizer for controlling the tonal quality, a Leslie
Effect for giving rotary speaker effects, a Reverb (for giving reverbration), a Tube Buffer
for adding tube “warmth”. (The built-in Leslie Effect does not appear in the signal of the
Leslie 11-pin terminal.)
EFFECT LOOP
The External Effect Loop is located post-internal Effects.
The details are on the next pages.
The functions introduced here will be explained
in detail from the next page.
Setting Up
HARMONIC DRAWBARS™
48
The 9 Drawbars (plus 2 for the Pedal) on this organ are used to create the basic sounds. Each
Drawbar is marked with the numbers 1 - 8. If you push back the Drawbar until you cannot see any
number at all, the sound of the Drawbar is not heard. If you pull it out to the fullest position The
sound level is maximum.
No Volume
Full Volume
The pitch of each Drawbar is as shown above, when the middle C is depressed. The footage
marked (') on the handle end of each Drawbar is originated from the length of pipes on a pipe
organ.
The numbers 1 - 8 on the “bar” portion of each Drawbar indicate the volume of the sound to be
produced as well as the guide to remember Drawbar settings.
Pull the fundamental (8'), the third harmonic (22/3') plus the fifth harmonic (13/5') Drawbars out
completely and play the keyboard. Notice how the sound resembles a clarinet.
If you push the 8' Drawbar half-way, you’ll notice the sound becomes more high-pitched and a bit
“harder”. Now pull the 8' drawbar back out fully and push the 22/3' and 13/5' in halfway. notice how
the sound becomes mellower. Experiment with the Drawbars to obtain your own personal favorite
sounds.
NOTE: You can change the characters of the Drawbars. (P. 72)
*#1
$OM%OM$2OMOwner’s Manual
49
Drawbars for the Swell/Great Manuals
Relation between the Preset Keys and the
Drawbars
The two sets of Drawbars on the left-hand side are for the Swell
Manual and the two on the right-hand side are for the Great Manual.
To actuate them, use the Preset Key [A<] or [B] respectively. When
the other [C<] to [A] Preset Keys are selected, the Drawbar registrations are recalled inside the organ, and the tone that plays will
not match the Drawbars physical settings.
<] to [A] are selected, you can
NOTE: Even while the Preset Keys [C<
operate the Drawbars and the preset registration will temporarily change. (P. 52)
WHITE DRAWBARS
In each Drawbar set, the white Drawbar (8') on the left end correspond to the fundamental sound. Each succeeding Drawbar to right controls the next octave harmonic.
BLACK DRAWBARS
The sounds of the black Drawbars, too, play important roles in building rich tones.
Their pitches are fifth and third to the fundamental. They contain the elements of all
different harmonics of such as the sweet and soft horn, mellow strings and so on.
BROWN DRAWBARS
The two brown Drawbars on the far left give depth and richness to the sound. The left
16' is one octave lower than the 8', and 51/3' is the third harmonic of the 16' fundamental.
Normally, the tones are built on the 8' fundamental, but, if you want to add depth to the
tone or to expand the playing range on the manual by one octave, the tones are built on
the 16' fundamental.
Drawbars for the Pedalboard
The Pedalboard plays the bass line and uses two Drawbars -16' and 8'.
The first Pedal Drawbar produces a tone at 16' pitch for a deep foundation bass, while
the second Pedal Drawbar produces a tone at 8' pitch, or one octave higher.
Setting Up
50
Drawbar Registration Patterns
The Drawbar Registration is matched by digits. It is easy to remember the typical combinations of
the 9 Drawbars by their forms.
The Drawbar Registrations are grouped into the following 4 patterns:
Flute family (2 step pattern)
Accompaniment Flute 8' I ....... 00
Accompaniment Flute 8' II ..... 00
Accompaniment Flute 8' III .... 00
Chorus of Flutes 16' ................ 80
Orchestral Flute 8' ................... 00
Piccolo 2' ................................. 00
Stopped Flute 8' ...................... 00
Tibia 8' ..................................... 00
Tibia 4' ..................................... 00
Tibia (Theater) 16' .................. 80
Wooden Open Flute 8' ............. 00
8460
3220
8600
8605
3831
0006
5020
7030
0700
8605
8840
000
000
000
002
000
003
000
000
030
004
000
Diapason family (check mark pattern)
Accomp. Diapason 8' .............. 00
Chorus Diapason 8' ................. 00
Diapason 8' .............................. 00
Echo Diapason 8' .................... 00
Harmonic Diapason 16' .......... 85
Harmonic Diapason 8' ............ 00
Harmonic Diapason 4' ............ 00
Horn Diapason 8' .................... 00
Open Diapason 8' .................... 01
Solo Diapason ......................... 01
Wood Diapason 8' ................... 00
8874
8686
7785
4434
8524
8877
0606
8887
8866
8855
7754
210
310
321
210
100
760
045
480
430
331
321
NOTE: Some of the names on this page may be unfamiliar. They represent the names of types of pipes on a pipe
organ. The “Diapason” is the fundamental type of pipe on a pipe organ.
Reed family (triangle pattern)
Bassoon 16' ............................. 44
Clarinet 8' ................................ 00
English Horn 8' ....................... 00
Flugel Horn 8' .......................... 00
French Horn ............................. 00
Kinura 8' .................................. 00
Oboe 8' ..................................... 00
Trombone 8' ............................. 01
Trumpet 8' ............................... 00
Tuba Sonora 8' ........................ 02
Vox Humana 8' ........................ 00
7000
6070
3682
5777
7654
0172
4764
8777
6788
7788
4720
000
540
210
530
321
786
210
530
650
640
123
String family (bow pattern)
Cello 8' ..................................... 00
Dulciana 8' ............................... 00
Gamba 8' I ............................... 00
Gemshorn 8' ............................ 00
Orchestral String 8' ................. 00
Salicional 8' ............................. 00
Solo Viola 8' ............................ 00
Solo Violin 8' ........................... 00
Viola da Gamba 8' ................... 00
Violina 4' ................................. 00
Violone 16' .............................. 26
3564
7770
3484
4741
1464
2453
2474
3654
2465
0103
3431
534
000
443
321
321
321
341
324
432
064
000
NOTE: The “Strings” and “Reeds” mentioned here are not analogous to orchestral voices. The names here refer to
types of pipes found in a pipe organ and the sounds are not meant to sound as actual violins, trumpets,
oboes, etc.
*#1
$OM%OM$2OMOwner’s Manual
51
Modern Drawbar Registrations
The Drawbar registrations introduced on the previous page are typically for classical music.
They were created at the dawn of the Hammond Organ, when it was intended to sound like a
pipe or church organ.
Later on, as the Hammond Organ spread throughout Jazz, Pop, Rock and (especially) Gospel
music, Some timeless registrations become common.
Jazz
Bluesey
Groovy & Funky
Max Power
APPLICATION OF PERCUSSION
When Percussion is used, the sound of the
1' Drawbar is cancelled. This enables the
technique of playing the organ switching
“Jazz” or “Bluesey” by turning on/off [PERCUSSION] while the registration itself is set
at “Bluesey”.
Setting Up
52
Controlling the Registration while playing a Preset
To temporarily modify the registration by operating Drawbars, while a Preset Key is selected
between [C<] and [A], operate either [A<] or [B] holding down the [PLAY] button.
In the registration, only the operated bar’s footage changes. For example, draw 1' of the Swell
Drawbar [A<] or [B] holding down the [PLAY] button, if you want to add 1' while playing the
Preset Key [G] of the Swell Manual.
NOTE: Pedal Drawbars are always working regardless of Preset Keys and link Great / Pedal (P. 76 #3).
1
“ON”
2
Draw with...
Press and Hold
*#1
$OM%OM$2OMOwner’s Manual
PERCUSSION
53
The touch-response percussion adds a clear-cut “attack” to the organ sound. It
is a Hammond exclusive. Percussion is usually combined with the Drawbar
sound.
[PERCUSSION] Tablet
Turns on the Swell (Upper) manual percussion when swell Preset [B] is selected. When percussion is activated the 1' Drawbar does not sound.
[PERCUSSION VOLUME] Tablet
This is for controlling the Percussion volume. SOFT for lower Percussion volume, and NORMAL for higher Percussion volume with the Drawbar volume a little lower.
[PERCUSSION DECAY] Tablet
This is for controlling the decaying speed of Percussion. SLOW for decaying slowly like a
chime, and FAST for decaying rapidly as a xylophone.
[PERCUSSION HARMONIC SELECTOR] Tablet
This is for setting the Percussion pitch. SECOND for the 2nd harmonic, i.e. the pitch of the 4'
Drawbar. THIRD for the 3rd harmonic, i.e. the pitch of the 2 2/3' Drawbar.
DECAY
Piano sound gradually fades even if you
keep the key down. This is called “decay”.
A violin, keeps sounding at a certain volume. This is called “sustain”.
NOTE: You can fine-set Percussion. (P. 74)
Notes
“Percussion does not sound!”
The factory default setting: Percussion will not sound except at the Preset Key [B] (See left).
NOTE: You can set any Preset Key to sound Percussion. (P. 77 #7)
DRAWBAR CANCEL
While [PERCUSSION] is on, 1' of the Swell Drawbars is disabled.
NOTE: You can set to play 1' Drawbar, while Percussion is on. (P. 74 #5)
SINGLE TRIGGER
If you play legato on this organ, only the first note of Percussion is output, and it does not trigger
again unless you fully release all keys held on the Swell Manual.
Setting Up
VIBRATO AND CHORUS
54
VIBRATO adds warmth to the tone by slightly oscillating the Drawbar pitch.
CHORUS adds richness to the sound by doubling the fundamental slightly detuned.
[VIBRATO SWELL] Tablet
This enables the Vibrato and Chorus effects on the Swell manual.
[VIBRATO GREAT] Tablet
This enables the Vibrato and Chorus effects on the Great manual.
NOTE: You can choose to add Vibrato & Chorus effects on the Pedalboard. (P. 82 #10)
[VIBRATO AND CHORUS MODE] Knob
This knob controls the depth of Vibrato and switches ON and OFF the Chorus Effect.
V-1:
V-2:
V-3:
C-1:
C-2:
C-3:
Light Vibrato
Standard depth Vibrato
Deepest Vibrato
Light Chorus
Standard depth Chorus
Deepest Chorus
NOTE: You can fine-adjust the Vibrato and Chorus Effect. (P. 82)
*#1
$OM%OM$2OMOwner’s Manual
OVERDRIVE
55
The overdrive gives distortion to the sound by highly increasing the pre-amplifier
input gain. The genuine tube circuitry allows a wide range of sound from unclipped
warm and clean to a hard distorted overdrive, by varying the amount of the overdrive
control.
[OVERDRIVE] Knob
This is for controlling the amount of overdrive of the tube amp circuit.
Controls the distortion amount. Full left is “clean”. The overdrive effect increases an you
rotate the knob.
NOTE: You can fine-set the overdrive. (P. 80)
TUBE AMP CIRCUIT
Tubes are rarely used in modern electric
apparatuses because semi-conductors
have better characteristics and tubes are
inferior in many aspects.
In the matter of sound production, the qualities of a genuine tube preamp have not
been surpassed or duplicated.
In this organ, a real Tube circuit is used in
the preamp.
Setting Up
LESLIE
56
The Leslie Speaker produces its unique effect by utilizing rotors that give tremolo,
vibrato and motion to the sound.
The Leslie Speaker is controlled by the Leslie Speed Switch. If no Leslie Speaker is
connected, this switch controls the built-in Leslie Effect.
[CHORALE]
Rotors will turn slowly, producing an effect suitable for use with hymns, classical style
music and some slower songs.
[STOP]
Rotors do not turn. Animation can be provided by using Vibrato and Chorus.
[TREMOLO]
Rotors will speed up and rotate fast to produce a rich full sound.
NOTE: Some Leslie Speakers will not recognize the “stop” position.
NOTE: You can finely set the charactics of the built-in Leslie effect etc. (P. 84)
WHAT IS THE LESLIE EFFECT?
In the Leslie speakers, an amplifier and two rotors are incorporated, the “Horn Rotor” for the treble and the “Bass Rotor” for the
bass.
The Horn Rotor uses a horn driver, and a Woofer speaker (usually
a 15”) fires into the Bass rotor. Each is driven by a speed controlled motor. The motion causes the “Doppler effect” that creates
the distinctive Leslie sound.
There are also models that have not only rotors but stationary speakers.
The circuit that sends the sound to the rotors is called “Rotary Channel” and the stationary speaker circuit is called “Stationary Channel”.
The built-in “Virtual” Leslie simulates the sound of the Mechanical
speaker. The best effect is obtained when connected to a stereophonic amp or sound system.
When a Leslie Speaker is connected, the sound of this organ is
sent only to the rotary channel, and the sound input from the LINE
IN jack is sent to the stationary channel.
*#1
$OM%OM$2OMOwner’s Manual
EQUALIZER, REVERB
57
The Equalizer and the Reverb add a final touch to the tone.
The Equalizer regulates the tonal quality. The Reverb adds the effect of playing in a
concert hall.
You control their basic functions on the panel under the left side of the keydesk.
Equalizer
[BASS] Knob
BASS is assigned here at the time of shipment from the factory. This increases/decreases the bass
sound. About ±9dB is adjustable at 100Hz.
[TREBLE] Knob
TONE is assigned here at the time of shipment from the factory. It increases/decreases the treble
sound. About -9 to +3dB is adjustable at 10kHz.
NOTE: The Equalizer actually has 3 bands and 1 tonal function, and one function is assignable to each
BASS, TREBLE knob. (P. 88)
NOTE: The “Tone” function here refers to the unique internal control on the vintage B-3 that gently cut the
treble. This is a different function than the “Treble” EQ.
Reverb
[REVERB] Knob
This is for controlling the depth of the reverb effect. It gives no reverb effect at full counter-clockwise.
The reverb gets deeper as it is turned further clockwise.
NOTE: You can finely set the reverb. (P. 89)
Setting Up
PRESETS
58
You can record all the aforementioned settings to the Presets. In the factory default
setting, only the Drawbar registrations are called as on vintage B-3’s.
BANK and KEY
There are 5 “BANKS” of presets, each containing 12 presets corresponding to the reverse keys to the left of each manual. The SWELL
and GREAT presets are independent of each other, but the BANKS
are common to both manuals. You may only select one BANK at a
time.
To select a “BANK”, press the [PARAM] button in the PLAY mode.
Then select a “KEY” by simply pressing a Preset Key. Refer to the
chart below for each Key and the name.
NOTE: The preset keys have no association with the “key signature”
of the music that you might play.
The left-most key [C] is called “CANCEL” and used to mute the
manual. No setting can be recorded to this key.
You can record the settings to all the keys [C<] to [A].
The right-hand side keys [A<] and [B] are also called “ADJUST
PRESETS”, and are used for creating sounds using the Drawbars
A< or B respectively.
Please refer P. 43 for recording Presets, and P. 37 for calling Presets.
COMBINATION PRESETS
On the original B-3 organ the preset keys only stored drawbar registration information.
On this organ, various parameters such as Vibrato & Chorus and
Percussion are recorded to the Preset Keys, as well as the Drawbar registrations. These are called “Combination Presets”.
NOTE: You can set the parameters to call on the Preset keys Bank
by Bank. (P. 76)
*#1
$OM%OM$2OMOwner’s Manual
59
Using Plural Presets at the Same Time
When pressing a Preset Key, the previously selected key is released.
However, it does not mean you can not select more than one key.
If you select more than one Preset Key at the same time, the registrations recorded for all those keys are mixed. Try this.
If the other parameters than the registrations in the Preset Function
Mode are contained in the preset, the contents of the key pressed
last are called out.
In case you select all the Preset Keys by mistake and the Preset
Keys do not function, press the [C] Preset Key, to release all of the
Preset Keys.
Setting Up
60
Naming the BANK
You can name each BANK. (The KEYs have no name.)
1
Go to MENU.
Press the [MENU/EXIT] button.
The [MENU] mode appears.
2
Go to the PRESET FUNCTION mode.
Press the [4] PRESET button, and go to the PRESET FUNCTION mode.
3
Input the NAME.
Up to 8 characters can be input.
[P
ARAM] button
[PARAM]
button: moves the cursor.
[V
AL
UE] button
[VAL
ALUE]
button: selects the letters.
The characters available are signs, numerals, Capital and small letters.
To return to the top of each character selection, press the [VALUE] button holding
down the [RECORD] button.
The Bank Name is recorded at the time of input. No recording operation is needed.
*#1
$OM%OM$2OMOwner’s Manual
VOLUME
61
The volume of this organ is controlled in three ways.
[MASTER VOLUME] Knob
This controls the total volume of this organ (except the sound input from the LINE IN
jack). This is the same as a volume knob on an ordinary electronic musical instrument or
audio equipment.
Expression Pedal
This is operated by foot. The volume increases as you fully depress the pedal. As you pull
back the pedal, the volume decreases. As the volume is lowered, the tone becomes warmer
as a side effect.
NOTE: The volume and tone change can be adjusted by the Expression Pedal.(P. 91)
NOTE: The Overdrive depth can be controlled by the Expression Pedal. (P. 80 #1)
[VOLUME] Tablet
Normal volume at NORMAL. The volume is reduced to 1/3 of the normal volume at
SOFT, with a small amount of Bass reinforcement.
When you play in a small room or practicing alone, you may play bass with rich deep tonal
quality even at reduced volume by setting the [VOLUME] tablet at SOFT, instead of lowering the volume by using the [MASTER VOLUME] knob.
Setting Up
Tone-Wheels and Multi-Contact Keys
62
Digital Virtual Tone-Wheels and Bus-Bar Multi-contact manuals
are used in this organ to replicate the sound, touch and feel of the
original Hammond B-3 as faithfully as possible. Let’s examine
these exclusive patented features a bit deeper.
the bow on a violin. The key-click, as it was called made the electric organ sound less electric, and...more organic! The sound was
fresh and new. The Hammond engineers tried valiantly to correct
this, but happily, they never did.
On modern electronic musical instruments, when a key is depressed,
the sound engine plays. When multiple keys are pressed, the ear
hears multiple notes, but this is an audio illusion. In actuality, only
one voice is sounding at a time, but they are cycling so fast it sounds
as if many notes are playing at once. The onboard processor “scans”
the manual for the notes pressed and feeds that information to the
sound engine. The technology is called “Keyscan” and “Dynamic
Voice Allocation”.
When the New B-3 was being designed, the hallmark was authenticity. But it didn’t make sense to recreate the mechanical Tonewheels of old. After all, it was just sine waves that they put out, and
that’s a child’s game in today’s digital technology. Previously, modern organ manufacturers (including Hammond) relied on looped
samples of vintage instruments. Close, but no cigar. What if the
entire concept of the B-3 was expressed in modern terms? 96 virtual tone wheels, each putting out their sine-wave constantly, just
as the mechanical ones did, so that when keys were played, the
entry point into each sine wave was random. The resultant phase
relationship between the tones was chaotic, and in this case chaotic
is good. The richness of tone would rival the sweetest vintage B-3.
Whereas the mechanical tone generator was not the way to go, the
bus-bar multi contact keying system could not be rightly dupli-
These technologies have worked admirably for synths, but they have
problems for replicating the original B-3 sound and touch. In the
mentioned technologies, there is one contact point, and even that is
subject to latency.
When the Hammond Organ was born in 1934, there was no digital
technology to rely on for the keying system. An ingenious mechanical system was devised using a stack of 9 contacts under each key,
9 bus-bars that ran the length of the manual, and an actuator rod
which would close the contacts from top to bottom as the key was
depressed.
Those bus-bars corresponded to each of the harmonics represented
on the drawbars. A complex wiring harness completed the matrix,
which sent the signals from the closed contacts of the manual to the
drawbars, which allowed, or suppressed the tones from the everspinning, ever-playing Hammond Tone-Wheels.
cated in the digital realm.
Hammond-Suzuki engineers found a way to leap 1930’s technology to the cutting edge by being faithful to the past with an eye on
the future. They reinvented the buss-bar multi-contact keying system in such a way that the touch is indistinguishable from a vintage
B-3.
Their efforts lie before you today, in your organ.
As the Hammond Organ gained popularity, musicians noted a few
curious side-effects courtesy of that mechanical action. One was a
rudimentary “touch sensitivity”. The actuator rod did not trip all
nine contacts at once, in fact, if the key was not fully depressed,
only a few contacts were closed. This put a randomness in the sound,
and was almost instantly exploited by organists everywhere. Dr.
Lonnie Smith wows audiences by simulating the sounds of Congas
on his Hammond. Jazz, Blues and Gospel organists developed a
move where they lightly “skipped” a chord up the manual, only to
blaze a glissando back down. The sound was, and is, indescribable,
but was an outlet for pure emotion. The great Jimmy Smith invented a registration/technique called “squabbling” that took full
advantage of the manual response.
The other happy side-effect was really a defect. When you consider
the Hammond Keying system, it might be easier to think of it as a
whole bunch of electric switches. By nature; through age, corrosion, and contamination, electric switches become “dirty”. Witness
the “crackle” on older radios, or the flicker of a light. The Bus-Bar
switches on Hammond were not exempt, and they started to exhibit
symptoms of noise right from the start. The funny thing was, this
little random chatter gave a distinctive edge to the organ’s sound,
very much like the pick noise on a guitar, or the resinous scrape of
*#1
$OM%OM$2OMOwner’s Manual
63
USING THE
CONTROL PANEL
*#1
$OM%OM$2OMOwner’s Manual
OPERATION CONTROL PANEL
64
You can refine and tailor the settings made on the topside controls here, as
well as adjust the MIDI settings and all other parameters.
The display modes are PLAY, MENU, and FUNCTION.
The controls are explained on the following pages.
PLAY mode
MENU mode
FUNCTION mode
*#1
$OM%OM$2OMOwner’s Manual
PLAY MODE
65
The PLAY MODE is the basic display for all the operations. The necessary information for the normal play will be displayed.
To locate this mode:
1. Immediately after powering ON and the start up process is complete, the PLAY mode is
displayed.
2. If a different mode is displayed, press the [PLAY] button.
How to read the Display
Drawbar registration
SWELL Kbd/ PEDAL Part/ GREAT Kbd
You can toggle the two PLAY mode displays (the
bar display and the digital display) by pressing the
[PLAY] button.
BAR display
Preset Bank : Name
Pedal Sustain
DIGITAL display
Manual Bass
Button operation in this mode
Bar display:
turns on/off the Pedal Sustain.
Digital display:
turns on/off the Manual Bass function.
Switch the Bank.
Display the Menu.
Record the Presets.
Switch the display, Bar or Digital.
Using the Control Panel
MENU MODE
66
The MENU mode is the path for each function.
To locate this mode:
Press the [MENU/EXIT] button.
The FUNCTION displays are distributed over several pages. Use the [PAGE] buttons to
scroll through them and reach the desired display.
How to read the Display
PAGE
FUNCTION ITEM
Button operation in this mode
These buttons are for
scrolling from page to page.
You can jump to the top or
bottom page by pressing
these buttons holding down
the [RECORD] button.
These are for entering each
FUNCTION MODE corresponding
with the item displayed.
This button is for returning to the PLAY mode.
*#1
$OM%OM$2OMOwner’s Manual
FUNCTION MODE
67
The FUNCTION MODE is where you adjust the various parameters of the organ.
The displays generally follow the same format.
How to read the Display
This indicates there are PAGEs
above (or below).
PARAMETER
This indicates there is another section
to this page on the right (or on the left).
CURSOR
PAGE
NAME
VALUE
CURSOR
(Flashing VALUE)
In the display window of this organ, the
CURSOR is displayed by flashing the current value.
Button operation in this mode
Increases or decreases the value of the
Parameter indicated by the flashing CURSOR.
Holding it increases (or decreases) the value
continuously.
Pressing it while holding the [RECORD] button
increases (or decreases) the value quickly.
These buttons are for scrolling within
the pages of the display.
You can jump to the top or bottom
page by pressing these buttons with
holding down the [RECORD] Button.
These buttons are used to move the CURSOR right
or left for selecting the PARAMETER to change.
The CURSOR moves to the edge of the display and
on to the next page (on the right or left), if there is
one.
Pressing this button holding [RECORD] button, you
can move to the right or left page regardless of where
the cursor is.
Return to the PLAY mode.
Using the Control Panel
68
Example: Increase the depth of Vibrato at [V-3].
1
Locate the MENU Mode.
Press the [MENU/EXIT] button.
The MENU mode is displayed.
2
Selet the PAGE.
Search for the VIB&CHO page, using the [PAGE] button.
“VIB&CHO” is on PAGE B. Select PAGE [B].
3
Press the Number button.
Press the [2] button for “VIB&CHO”.
This calls the first page of the Vibrato and Chorus function mode.
*#1
$OM%OM$2OMOwner’s Manual
69
4
Move the CURSOR to the Parameter you want to change.
Vibrato Depth is on the “DEPTH” page. Move to that page using the
[PAGE] button.
“V3” is on the right end. Move the cursor (flashing value) to “V3”
using the [PARAM] button.
5
Change the Value.
Increase the value, using the [VALUE] button.
NOTE:
6
Repeat the operation 1 - 5, if you want to change other parameters.
Record in to the Preset Key.
The “Vibrato Depth V3” is a Preset Parameter, it will revert to the set value, if you
select any Preset Key (when the PRESET - P. LOAD - ANI/OD is “ON”).
If you wish to continue using the changed value, you must record the value into the
Preset Key.
PRESET PARAMETERS
Preset Parameters may be recorded into
each Preset Key.
They include the Parameters for setting the
status of the buttons/knobs on the top
panel, such as “Vibrato Depth V3” and others.
The overall common Parameters (which are
not included in the Presets) are called “Global Parameters.”
Using the Control Panel
LOCK THE DISPLAY IN PLAY MODE
70
This advanced feature allows you to put the organ into a special playing mode whereby
the Control Panel is rendered inoperative. Pressing any of the Select Touch Buttons
will have no effect. This is useful when you want to place the organ in public halls,
Churches or auditoriums.
Press and
Hold
To initiate the Display Lock function, switch on the power pressing and holding both PARAM
[W], [X] buttons and the [PLAY] button together. “Display LOCKED...” will be displayed
for a few seconds. To unlock it, do the same thing as above. This time “Display UNLOCKED..”
will appear for a few seconds.
NOTE:
You can operate the BANK switch, Pedal Sustain and Manual Bass while the Display Lock function
is on.
*#1
$OM%OM$2OMOwner’s Manual
71
SETTING THE
PARAMETERS
*#1
$OM%OM$2OMOwner’s Manual
DRAWBAR
72
In this mode, you set the Drawbar Parameters.
To locate this mode:
Press the [MENU/EXIT] button and display MENU, press the [PAGE] button, and select
PAGE A, and choose [1] DRAWBAR.
5
6
7
2
8
3
11
10
9
4
1
‹Setting the SWELL and GREAT Manual
1. TONE-WHEELS
Select the TONE-WHEEL SET (waveform) for the manuals.
BT
ype1
BType1
ype1:
Traditional tone-wheel sound of the original B-3. Leakage noise is included in
the waveform. You can not adjust the volume of the inherent leakage noise.
BT
ype2
BType2
ype2:
Traditional tone-wheel sound of the original B-3. Leakage noise is not included
in the waveform. You can add and adjust the volume of leakage noise.
Mellow
Mellow: Transparent sine wave
2. LEAKAGE
This is for setting the volume of Leakage Noise.
Setting Range is 0 to 127. The more you increase the value, the louder gets the volume.
3. FOLD-BACK - LOW
This allows you to set which key the FOLD BACK of the 16' Drawbar starts. (Fold-back:
Repeating the same octave in a certain range on the manual.)
The first key (= the far left key on the manual, next to the Preset Keys) is displayed as
“1C”. The setting range is 1C - 2C.
4. FOLD-BACK - HIGH
This allows you to set which key the FOLD BACK of the 1' Drawbar starts (= repeat the
same octave) in the upper-most range. The set range is 4G - 5C.
NOTE: The FOLD-BACK sets the 1' and also 11/3', 13/5', 2' and 22/3' Drawbars.
*#1
$OM%OM$2OMOwner’s Manual
TONE-WHEEL SET
Each Tone-wheel Set allows you to make fine adjustment. (P. 92)
LEAKAGE NOISE
On the original B-3, while the sound created by a certain tone-wheel goes through various circuits, the
sounds of the other plural tone-wheels are mixed. This
is called Leakage Noise. Leakage noise itself is unnecessary for synthesizing pure sounds. However, it is
accepted rather as one of the unique characteristics of
Hammond Organs.
Leakage Noise allows you to make finer adjustment.
(P. 92)
FOLD-BACK
As the number of the tonewheels was limited on the
original B-3, the organs were designed to repeat the
same octave in the upper-most or lower-most range.
This feature of this organ will simulate that.
73
‹Setting the PEDAL Part
5. TONE-WHEELS
This allows you to select the Virtual Tone-wheel set (waveform) of the PEDAL Part.
Normal
Normal:
Muted
Muted:
Synth1
Synth1:
Synth2
Synth2:
The traditional B-3 Tone-wheel sound
Analog-oscillating sound represented by the X-5.
Sawtooth waveform with sweep filter.
Dull square waveform.
6. ATTACK
This allows you to set the Attack Rate and the Key-Click Volume at ATTACK and RELEASE.
MAX CLK
CLK:
NORM CLK
CLK:
SOF
T CLK
SOFT
CLK:
NO CLK
CLK:
SL
OW A
TK
SLOW
ATK
TK:
Immediate attack with loud key-click.
Immediate attack with normal key-click.
Immediate attack with soft key-click.
A slightly slower attack without key-click.
Slow attack without key-click.
7. DECAY RATE
This allows you to choose whether the voice is continuously sustained, or decays while the
pedal is depressed.
The setting range is 1 - 5 and C. The higher the value gets, the longer the decay time. There is
no decay at C (=continuous).
8. SUSTAIN - LENGTH
This allows you to set the Release Rate (= the decay time after you release the key) of Pedal
Sustain, when the “P.SUS” on the PLAY Mode (P. 42) is ON.
1 is the shortest, and 5 is the longest decay time.
SUSTAIN
9. KEY MODE
This allows you to set the Pedal Part voice mode.
POL
Y:
POLY
Makes it possible to play up to 8 notes together.
MONO
MONO: Only the lowest note will sound, regarless of how many keys are depressed.
Not like the “Sustain” segment of a synth envelope generator. On this organ “Sustain” refers to
the decay of the note after the key or pedal is
released.
NOTE: The previously released note will be cut when you play the next one, even when the PEDAL
Part is in the POLY mode and “P. SUS” is ON.
10. SUB-DRAWBAR 16'
This is for controlling the harmonic combination of Pedal Drawbar 16'.
It is possible to control each footage of 16', 5 /3', 8', 4', 2 /3', 2', 1 /5', 1 /3'.
1
2
3
1
11. SUB-DRAWBAR 8'
This is for controlling the harmonic combination of Pedal Drawbar 8'.
It is possible to control each footage of 8', 4', 22/3', 2', 13/5', 11/3'.
SUB-DRAWBARS
The two Pedal Drawbars, 16' and 8', of on the
original B-3, did not simply produce the corresponding tone-wheel sounds but the sounds of
registrations composed of several harmonics.
These registrations differ from model to model
depending when the organs were made. SubDrawbar function is for controlling the registrations of Pedal Drawbars.
NOTE: All the parameters in these modes are
Preset Parameters. They are recorded
into the Combination Preset.
Setting the Parameters
PERCUSS (PERCUSSion)
74
In this mode, you set the parameters of the PERCUSSION.
To locate this mode:
1. Press the [MENU/EXIT] button and display MENU, then select PAGE A by the [PAGE] button
and press the [2] PERCUSS button.
2. Or, move any [PERCUSSION] tablet pressing the [MENU/EXIT] button.
5
6
3
4
1
2
1. LEVEL - SOFT
2. LEVEL - NORMAL
These are for setting the Percussion volume level. SOFT is the level when the [PERCUSSION VOLUME] tablet is in “SOFT”, and NORMAL is the level when it is in “NORMAL”.
3. DECAY - SLOW
4. DECAY - FAST
These are for setting the Percussion Decay time.
SLOW is the time when the [PERCUSSION DECAY] tablet is in “SLOW”, and FAST is
the time when it is in “FAST”.
The setting range is 1 - 15 and C. The higher the value gets, the longer the Decay time. At
C, there is no decay (Percussion sound is continuous).
5. DRAWBAR - 1' CANCEL
This mutes the 1' of the SWELL Drawbar while using PERCUSSION.
ON
ON: Mute
OFF
OFF: Does not mute.
6. DRAWBAR - LEVEL
Decreases the volume of the Swell Drawbars while using PERCUSSION, and [PERCUSSION VOLUME] tablet is in “NORMAL”.
-5dB
-5dB:Decreases the volume 5dB
-3dB
-3dB:Decreases the volume 3dB
0dB
0dB: No decrease in volume
NOTE: The parameters in those modes are all Preset Parameters. They are recorded to each
Combination Preset.
*#1
$OM%OM$2OMOwner’s Manual
1' CANCEL
The original B-3 had no key contact exclusive for percussion but uses the 1' contact for percussion. On this
organ, this is simulated.
DRAWBAR LEVEL
On the original B-3, the Drawbar volume was slightly
softer, when percussion was enabled. This is simulated on this organ.
TUNE
75
In this mode, you can tune and transpose the organ for playing in ensemble with other instruments and performers.
To locate this mode:
Press the [MENU/EXIT] button (MENU will be displayed), select PAGE A by the [PAGE]
button and press the [3] TUNE button.
1
2
1. TRANSPOSE
You can transpose the entire keyboard by semi-tones.
The setting range is -6 to +6.
Transpose affects:
ΠThe Organ Manuals/Pedals and Digital Toneweheel system
ΠThe MIDI External Zones
2. MASTER TUNE
This is for adjusting the PITCH of the entire organ.
The setting range is A = 430 - 450 Hz.
NOTE: The parameters in this mode are Global Parameters. They are recorded when the value is
set. Also, they are common at each Combination Preset.
Setting the Parameters
PRESET
76
In this mode, you name your Bank, and determine how to recall the Combination Presets.
To locate this mode:
Press the [MENU/EXIT] button and display MENU, then press the [PAGE] button to select
PAGE A and press the [4] PRESET button.
2
3
4
5
6
1
‹BANK NAME
1. BANK NAME (B)
This allows you to name the current Bank using up to 8 letters.
Move the cursor by the [PARAM] button, and choose the letters by the [VALUE] button or the
[VALUE] knob.
The BANK name is recorded at the time of operation, so no recording operation is needed.
‹PRESET LOAD
This allows you to choose the operation of the Preset Keys.
2. PRESET LOAD - LINK GREAT/PEDAL (B)
This is for setting whether or not to call out the Pedal part Preset simultaneously by the Great
Preset Key.
In this mode, recording a preset on the Great (Lower) manual will also record the Pedal registration. This was not possible on vintage B-3’s.
3. PRESET LOAD - REGISTRATION SWELL (B)
This is for setting whether or not to call out the registration of the Swell manual by the Swell
Preset Key.
4. PRESET LOAD - REGISTRATION GREAT (B)
This is for setting whether or not to call out the Great Manual registration by the Great Preset Key.
5. PRESET LOAD - DRAWBAR (B)
This is for setting whether or not to call out the Drawbar Parameters by the Swell Preset Key.
*#1
$OM%OM$2OMOwner’s Manual
PRESET LOAD
Only the Drawbar registrations were recorded
to the Preset Keys on the original B-3. On this
organ, not only the Drawbar registrations, but
also various parameters will be recorded simultaneously. These are called “Combination
Presets”.
As the factory default, only the Drawbar registrations are called out as on the original B3(except Bank 4: ShowCase). But you may
save various parameters that can be called
out by turning on the Preset Load.
77
7
8
9
10
11
6. PRESET LOAD - PERCUSSION (B)
This is for setting whether or not to permit the Percussion division to play while the selection of the
Swell Preset Key is other than [B] and whether to call out the tablets of Percussion, or Percussion
Parameter by the Swell Preset Key.
7. PRESET LOAD - MANUAL BASS (B)
This is for setting whether or not to call out the Manual Bass ON/OFF, and upper limit by the Great
Preset Key.
8. PRESET LOAD - EXTERNAL ZONE SWELL (B)
This is for setting whether or not to call out the External Zone Parameter of the Swell manual by the
Swell Preset Key.
9. PRESET LOAD - EXTERNAL ZONE GREAT (B)
This is for setting whether or not to call out the External Zone Parameters of the Great manual by the
Great Preset key. The External Zone Parameters of the Pedal part is also called out, if the Link-Great/
Pedal is on.
10. PRESET LOAD - EQUALIZER/REVERB (B)
This is for setting whether or not to call out the Parameters of the Equalizer and Reverb by the Swell
Preset key.
11. PRESET LOAD - ANIMATION/OVERDRIVE (B)
This is for setting whether or not to call out the tablets and parameters of Vibrato, Leslie and Overdrive by the Swell Preset Key.
NOTE: Each Parameter (B) of Preset Load is a Bank Parameter. It is set only for the BANK currently selected.
Setting the Parameters
78
See the current value (Temporary Scope)
The Combination Presets recall settings internally, and these settings will not reflect
the current physical positions of the Drawbars, tablets and knobs on the organ’s top
panel.
By means of the Temporary Scope function, you can tell the present value of each
tablet or knob as selected by the Combination Preset.
‹VIBRATO AND CHORUS
To see the value of each tablet and knob of Vibrato and Chorus, move
either knob of the [VIBRATO SWELL], [VIBRATO GREAT] or [VIBRATO and CHORUS] knob, holding down the [PLAY] button on the
Control Panel.
Press and
Hold
*#1
The present value of Vibrato & Chorus is displayed. Their values are
not affected by the actual physical positions of the tablet or knobs.
$OM%OM$2OMOwner’s Manual
79
‹PERCUSSION
To see the present value of the Percussion tabs, move any of the [PERCUSSION], [PERCUSSION VOLUME], [PERCUSSION DECAY],
[PERCUSSION HARMONIC SELECTOR] tablets, holding down the
[PLAY] button on the Control Panel.
Press and
Hold
The present value of Percussion appears on the display. At this time,
the present value is not affected by the current position of the tablet.
‹LESLIE
To know the present Leslie mode, operate the Leslie Speed Switch or
the Foot Switch (if Leslie C/T is assigned), holding down the [PLAY]
button on the Control Panel.
Press and
Hold
The present Leslie mode is displayed. The Leslie mode itself is not
affected by this operation.
‹Other Knobs
Besides the aforementioned knobs. The [OVERDRIVE], [REVERB],
[BASS], [TREBLE] knobs are on this organ. If you operate them holding down the [MENU/EXIT] button, you can short cut to the function
mode relating to those knobs.
Setting the Parameters
TUBE AMP (TUBE pre-AMP)
80
The Tube Pre-Amp settings are made in this mode.
To locate this mode:
1. Press the [MENU/EXIT] button to display the MENU, select PAGE B by the [PAGE] button,
and then press the [1] TUBE AMP button.
2. Or, move [OVERDRIVE] knob pressing the [MENU/EXIT] button.
4
5
3
1
2
1. OVERDRIVE - EXPRESSION
This is for varying the Overdrive value by operating the Expression.
EX
-OD
EX-OD
-OD:
If you operate the Expression Pedal, the overdrive changes along with the volume.
OD
-EX
OD-EX
-EX:
The Expression affects only the volume and not the overdrive value.
2. OVERDRIVE - BIAS
This parameter finely adjusts the bias voltage of the tube 12AU7.
The setting range is -32 to +31.
3. OVERDRIVE - DRIVE
This is for adjusting the Overdrive Value.
USING THE EQUALIZER TOGETHER
If you distort the sound by overdrive or by changing
the bias, new harmonics are added. By using the
equalizer, a wider range of tones may be acquired.
The overdrive increases as the value increases.
This is linked with the [OVERDRIVE] knob on the volume panel.
4. BUFFER - TUBE AMP
This is for switching the buffer on/off by the tube 12AX7. All the signals of the Swell,
Great, Pedal pass through this circuit.
NOTE: If you are using the LINE OUT jack and the HEADPHONE jack, the Buffer Amp works only
on R (right).
5. BUFFER - BIAS
This parameter finely adjusts the bias voltage of the tube 12AX7.
The setting range is -32 to +31.
NOTE: The parameters in these modes are Preset Parameters and are recorded to each Combination Preset.
™ Please understand that the tone color or the depth of Overdrive varies from
organ to organ even if the parameter are the same, as the characteristic of
each tube is different.
*#1
$OM%OM$2OMOwner’s Manual
BUFFER AMPLIFIER
A Buffer Amp changes the characteristics of the
sounds passed through it, without modifying the gain.
This organ uses a tube and a transformer in its buffer
amp.
81
Bias voltage and Nonlinear Distortion
To make the vacuum tube function as an audio amplifier, a minus voltage called bias voltage is
added to the input terminal (called grid) as well as the audio signal.
Although, the bias voltage is generally fixed so that the distortion of the output wave-form of
the tube is at the minimum, the bias voltage can be changed when the tube amplifier is overdriven
on this model.
By this parameter, you can adjust the characteristic of distortion to your taste.
GRID
The grid is one of the poles of the tube. In the
triode tube used on this model, there are 3 poles,
the cathode, the plate and the grid. The electrons are attracted towards the plate if the heated
cathode is loaded with voltage. By changing the
voltage on the grid, the voltage flowing to the
plate greatly changes.
NONLINEAR DISTORTION
An amplifier without distortion amplifies input in
proportion (=linear) with output, as shown in
the figure below.
The change the bias voltage gives to the sound distortion may not be very noticeble, depending on the drive amount or the drawbar registration. The best way to check it precisely is as
follows:
1.
2.
3.
4.
Set the Drawbar registration at “00 8000 000” (either manual).
Locate the TUBE AMP - OD page.
Set the Drive near 40. (Make sure it is not the maximum value.)
Move the cursor to BIAS.
If the bias voltage is changed, input and output
are not in proportion with each other, as shown
in the figure on the left. The distortion caused
by this is called non-linear distortion.
5. Play the chord on the manual as shown.
CLIPPING DISTORTION
If the drive is at the maximum, the end of the
waveform is cut (off), as shown in the figure
below. This is called clipping distortion.
Change the value of BIAS, pressing the keys. The degree of distortion is slight near “0”, but
the distortion increases, if you change the value towards “+” or “-”. Such a distorting sound is
called “nonlinear distortion”.
NOTE: On the original B-3, distortion occasionally would occur naturally as the instrument would
age. On this organ, you can create natural-sounding distortion intentionally.
Setting the Parameters
VIB&CHO (VIBrato and CHOrus)
82
In this mode, you change the settings of the Vibrato and Chorus.
To locate this mode:
1. Press the [MENU/EXIT] button to display the MENU, select PAGE B by the [PAGE] button,
and then press the [2] VIB&CHO button.
2. Or, move any [VIBRATO] tablet pressing the [MENU/EXIT] button.
10
4
1
5
6
7
2
8
9
3
1. VIBRATO - RATE
This is for setting the Speed of the Vibrato and Chorus effect.
The setting range is 6.10 - 7.25 Hz.
2. VIBRATO - TREMOLO
This is for setting the Tremolo (amplitude modulation) of the Vibrato and Chorus effect.
The setting range is 0 - 15.
3. VIBRATO - EMPHASIS
This is for setting the Emphasis (high frequency boost) of the Chorus effect (C1/C2/C3).
The setting range is 0 - 9 dB.
4. to 9. VIBRATO - DEPTH V1 to C3
These are for setting the Depth of the each Vibrato and Chorus effect mode.
The setting range is 0 - 15.
10. VIBRATO - TABLET GREAT
This is for setting on which part to put the Vibrato & Chorus effect by the [VIBRATO GREAT] tablet.
GREA
T & PED
AL
GREAT
PEDAL
AL:
The Vibrato and Chorus effect works on the Great manual and Pedalboard.
GREA
T ONL
Y:
GREAT
ONLY
The Vibrato and Chorus effect works only on the Great manual.
NOTE: The parameteres in these modes are Preset Parameters and are recorded to each Combination Preset.
*#1
$OM%OM$2OMOwner’s Manual
83
Vibrato and Chorus of Hammond Organs
On string instruments, the vibrato effect is created by changing the string tension by one’s
fingers. On wind instruments, by changing the strength of breath. On electronic instruments
with analog circuitry, by modulating the oscillator. As the rotation of the tone-wheels of the
original B-3 was stabilized by the synchronous motor, it was not possible to provide a vibrato
effect. On these models, the vibrato effect was obtained by modulating the signal post-generator.
The vibrato & chorus system of the original B-3 consisted of a 9 stage delay line using LC
phase shift circuits. This produced a very short delay of about 1 ms. Tones were passed through
coils, delaying the phase. Several coils were connected in tandem and when the output of each
tap was passed from the top to the last by turns, the pitches gradually lowered. By taking the
output of each tap from the last to the top by turns on the contrary, the pitch would gradually
rise. These operations were automatically made by turning the scanner with a motor.
The scanner was used to select one of multiple input terminals by the static connection. As
each terminal was selected by the “blades” which approached each other, a popping noise like
that of a switch did not occur and the signals of neighboring terminals cross-faded and switched
themselves.
The mode-selection of vibrato effects was made by changing the range of the connecting tap.
As this system modulated the produced tonal signals and not the oscillator, the original sound
could be heard without the vibrato effect. By mixing the sound with the vibrato effect and the
original sound, the chorus effect was obtained.
On this model, the chorus and vibrato effects are simulated and modeled in the original fashion digitally, by the DSP, without using moving parts.
Fundamental diagram of VIBRATO equipment
Setting the Parameters
LESLIE
84
In this mode, you make the settings for the built-in Leslie Effect.
To locate this mode:
There are many parameters for the built-in Leslie Effect. These
individual settings are not recalled by the Combination Presets,
or by bank settings. The built-in Leslie parameters are grouped
in macro-settings called “CABINETS”. You select the CABINET NUMBER in the Combination Presets where this selection
is saved as part of the Preset.
1. Press the [MENU/EXIT] button to display the MENU. Then
select PAGE B by the [PAGE] button and press [3] LESLIE.
2. Or, move Leslie Speed Switch pressing the [MENU/EXIT] button.
20
18
19
12
13
14
15
16
5
6
7
8
9
17
10
11
3
4
2
1
‹CABINET NUMBERS
1. CABINET NUMBER
Here you select the CABINET NUMBER to use in the Combination Presets.
The setting range is 1 - 8. The “*” will be displayed when the Leslie Parameters are CONCEPT OF THE CABINET NUMBERS
Each Cabinet represents one virtual Leslie Speaker prechanged from this Cabinet Number.
‹LESLIE PARAMETERS
2. CABINET NAME
This is for assigning the Cabinet Names.
Move the cursor by the [PARAM] button and select letters by the [VALUE] button.
In this mode, only the present value “Temporary” changes and there is no determining
operation. You must record the name by doing “Recording the Cabinet” as explained in
the next paragraph. Otherwise the data will be lost.
3. AMPLIFIER
This sets the type of the virtual power amplifier.
Solid
Solid: Simulated Solid-State Amplifier with a flat characteristic
Tube
ube: Simulated Tube Amplifier with a warm characteristic.
*#1
$OM%OM$2OMOwner’s Manual
pared by the Leslie Parameter.
This parameter is the only Preset Parameter in this
mode.
85
4. SPEAKER
This sets the type of the virtual speaker.
RotSmall
RotSmall: A small Leslie speaker represented by Leslie 145
RotLarge
RotLarge: A large Leslie speaker represented by Leslie 122
Station
Station: A stationary speaker represented by Hammond PR-40
5. CHORALE SPEED - HORN
12. CHORALE SPEED - BASS
Here the Speed of the virtual Rotor is set for Chorale mode.
The setting range is 0, 24 - 318 rpm. It does not rotate at 0.
6. TREMOLO SPEED - HORN
13. TREMOLO SPEED - BASS
Here the Speed of the virtual Rotor is set for Tremolo mode.
The setting range is 0, 24 - 453 rpm. It does not rotate at 0.
7. HORN LEVEL
14. BASS LEVEL
The Volume of each virtual Rotor is set. The setting range is 0 to -12dB.
8. RISE TIME - HORN
15. RISE TIME - BASS
Here the Time is set for the Rotor to reach the maximum Tremolo Speed, when
changing from Chorale or Stop to Tremolo mode. The setting range for the Horn
Rotor is 0.2 - 5.0s, and that for the Bass Rotor is 0.5 - 12.5s.
9. FALL TIME - HORN
16. FALL TIME - BASS
Here the Time is set for the virtual Rotor to reach the minimum Chorale speed,
when changing from Tremolo to Chorale mode. The setting range for the Horn
Rotor is 0.2 - 5.0s, and that for the Bass Rotor is 0.5 - 12.5s.
10. BREAK TIME - HORN
17. BREAK TIME - BASS
Here the Time is set for the virtual Rotor to stop, when changing from Tremolo
mode to Stop mode. The setting range for the Horn Rotor is 0.2 - 5.0s, and that for
the Bass Rotor is 0.5 - 12.5s.
11. HORN CHARACTER
Here the Tone of the Horn Rotor is set.
“FLAT” has no boost or cut in freqencies, and the others are have “peaks” in various tonal ranges.
18. MIC - ANGLE
This is the parameter to set the virtual LOCATIONS of the two “microphones” for
the virtual Leslie Speaker.
The ANGLE decides the distance between the two virtual mikes.
The setting range is 0 - 180 degrees. Farther settings exhibit more stereophonic
characteristics.
19. MIC - DISTANCE
This is the parameter to set the DISTANCE between the virtual Leslie Speaker and
the “microphones”.
The setting range is 0.3 - 2.7m. The more the value increases, the less intense the
sound.
NOTE: When you operate the parameters 2 - 19, the setting range will be lost after the
power is switched off, if you do not do the recording operation of the next paragraph.
Setting the Parameters
86
20. STOP MODE
This sets the mode when the Leslie Speed Switch is at “STOP”.
STOP
STOP:
The virtual rotors stop.
THROUGH
THROUGH:
The Leslie Effect is bypassed. (Through)
NOTE: This parameter is a Preset Parameter. It is recorded to each Combination Preset.
*#1
$OM%OM$2OMOwner’s Manual
87
Record the Cabinets
The Leslie parameters (2 - 20 of the previous paragraph) can be
recorded with the Cabinet Numbers, enabling their choice in each
Combination Preset.
1
Enter the desired name for the Cabinet.
2
Press the [RECORD] button in the setting mode of the Leslie Parameter.
The Cabinet Selection mode is displayed.
3
Select the Cabinet Number to record by the [PAGE] button.
4
Press [4] OK, and the Cabinet’s parameters are recorded.
The display during the recording the recording operation shows as
illustrated.
NOTE: If you wish to cancel the recording, press the [MENU/EXIT] button.
Setting the Parameters
EQ/REV (EQualizer/REVerb)
88
In this mode, you adjust the settings for the Equalizer and Reverb.
An Equalizer is used to adjust the tonal quality. The built-in Equalizer consists of 3 bands and
a a recreation of the unique “tone” control that was part of the vintage B-3. The Bass and
Treble bands are handled by “shelf” equalizers, and the Mid band is handled by parametric
control.
The Reverb effect is for adding the atmosphere of a concert hall, room, and other chambers.
To locate this mode:
Press the [MENU/EXIT] button for the MENU, select PAGE B by the [PAGE] button, and then
press the [4] EQ/REV button.
8
9
6
1
2
10
11
12
13
7
3
5
4
‹EQUALIZER
1. TONE CONTROL
This is a simulated original B-3 TONE CONTROL. Its response is unique, but its basic
response is to gently cut the overall treble.
The setting range is -9 to +9, and it becomes neutral when set at “0”.
“-1” corresponds to the maximum of the original B-3 tone control, “-5”, the middle, “-9”,
the minimum. The tone control found on the original B-3, its value can not be set at “+”,
but on this model it’s possible to boost treble to some extent.
NOTE: You can locate this page by moving [BASS] or [TREBLE] knob pressing the [MENU/
EXIT] button.
2. GAIN - BASS
3. GAIN - MIDDLE
5. GAIN - TREBLE
These are for doing the Boost/Cut of Bass, Mid-range and Treble respectively.
The setting range is -9 to +9. It is neutral at 0.
4. FREQUENCY - MIDDLE
This is for setting the Central Frequency to vary at Gain - Middle (3).
The setting range is 180Hz - 2.9kHz.
NOTE: These parameters are Preset Parameters and are recorded to each Combination Preset.
6. KNOB - BASS
7. KNOB - TREBLE
These sets the functions to assign to the [BASS], [TREBLE] knobs.
Bass and Middle gains can be assigned to the [BASS] knob, and Treble gain and Tone
Control to the [TREBLE] knob.
NOTE: These parameters are global parameters and are recorded at the time the value is set. It
is common for each Combination Preset.
*#1
$OM%OM$2OMOwner’s Manual
THE EFFECTIVE USE OF THE MIDDLE FREQUENCY
The frequency response of the horn rotor in the Leslie
speaker is not flat. It has a peak from 1kHz to 3kHz.
This peak is effective in “cutting through” any ensemble
playing.
If you use this organ through line out without a Leslie
speaker, you can duplicate effect by setting the FREQUENCY - MIDDLE to approximately 2kHz, and the
GAIN - MIDDLE to “+”.
89
‹REVERB
8. REVERB - DEPTH
This sets the Depth of the Reverb Effect.
The setting range is 0 - 15. As you increase the value, it will give the effect of performing in a
larger room.
NOTE: You can locate this page by moving [REVERB] knob pressing the [MENU/EXIT] button.
9. REVERB - TYPE
This sets the Types of Reverb Effect.
Room 1
1:
Room 2
2:
Live
Live:
Hall 1
1:
Hall 2
2:
Church
Church:
Plate
Plate:
Spring
Spring:
Delay
Delay:
PanDly
anDly:
RevDly
RevDly:
Small room
Large room
Ambient room
Large Hall
Small Hall
Church
Iron-plate Reverb
Spring Reverb
Delay
Panning Delay
Reverb + Delay
10. REVERB - TIME
When the Type (9) is set at Room 1 to Spring or RevDly, it sets the Time for Reverb to decay.
The setting range is 0 - 31. The higher the value, the longer the decay.
11. REVERB - DELAY TIME
When the Type (9) is set at Delay, PanDly, RevDly, this sets the delay time.
The setting range is 4.7 - 2000 ms. The higher the number, the longer the delay.
NOTE: You can set the delay time with the foot switch (P. 91 #4).
12. REVERB - DELAY FEEDBACK
When the Type (9) is at Delay, PanDly, RevDly, it sets the amount of Feedback. (How many
times the sound repeats.)
The setting range is 0 - 96%. The higher the value, the more repeats.
13. LESLIE ON REVERB
This sets the routing of the Reverb and Leslie Effect.
OF
OF: Leslie before Reverb
ON
ON: Reverb before Leslie
NOTE: These parameters are Preset Parameters and are recorded to each Combination Preset.
PRESET PARAMETERS
Equalizer and Reverb are Preset Parameters, designed to be actively used as one of the tone-making parameters.
If you are using the EQ and Reverb to compensate
for the space you are performing in, It is advisable
to switch off the P.LOAD EQ/RV in the Preset function mode so, the Equalizer and the Reverb value
will not change when a preset is recalled. (P. 77
#11)
Setting the Parameters
MANBS (MANual BaSs)
90
This mode is for setting the highest note to that will play using the Manual Bass function.
To locate this mode:
Press the [MENU/EXIT] button for the MENU, select PAGE C by the [PAGE] button, and then
press the [2] MANBS button.
1
1. MANUAL BASS - LIMIT
Sets the highest note of the Manual Bass functions on the Great manual.
NOTE: In this parameter, you can set the value by pressing the [RECORD] button, while holding
down a note on the Great manual.
*#1
$OM%OM$2OMOwner’s Manual
CONTROL
91
This mode is for setting the Motor Control Switch, Foot Switch and Expression Pedal.
To locate this mode:
Press the [MENU/EXIT] button and display the MENU and select PAGE C by the [PAGE]
button, and then press the [3] CONTROL button.
5
6
7
8
4
1
2
3
‹MOTOR CONTROL SWITCH
1. MOTOR - DOWN (G)
2. MOTOR - UP (G)
This is for setting the time required for the pitch change, when you
operate the [MOTOR CONTROL] Switch.
The setting range is 0.1 - 9.9 seconds.
NOTE: You can locate this page by moving Motor Control switch pressing the [MENU/EXIT] button.
3. MOTOR - AMP (G)
This is for setting the motion of the amp when you push the [MOTOR CONTROL] switch to “DOWN”.
If you switch ON, the pitch and volume drop together.
‹FOOT SWITCH
4. FOOT SWITCH - FUNCTION (G)
This is for setting the function of the Foot Switch.
OFF
OFF: Foot Switch is disabled.
LESLIE C/T AL
T, MOM
ALT
MOM:
These are for switching Chorale/Tremolo of the Leslie Effect. At ALT, Chorale/Tremolo is alternately switched at
each press of the Foot Switch, and switches to Stop if
pressed for longer than 1 second. At MOM, the Leslie effect
switches to Tremolo, as long as the foot switch is depressed, and switches to Chorale when you release it.
SPRING
SPRING:
This is for producing the effect of shaking a spring reverb.
DELA
Y TIME
DELAY
TIME:
This function sets the delay time (P. 89 #11) of the reverb
effect(if the “delay” setting is selected), by rhythmic tapping the foot-switch. The delay time will be set to the tempo
at which you tap the foot switch. By pressing and holding
the foot-switch, the delay sound will be erased.
REVERB DEPTH:
Changes the Reverb Depth to MAXIMUM while pressing
the Foot Switch regardless of the Reverb parameter setting.
the organ silent, when the Expression is at minimum, “0dB” produces no reduction in volume.
6. EXPRESSION - LIMIT LF (G)
7. EXPRESSION - LIMIT HF (G)
These are for setting the levels to maintain for low and high frequencies when the Expression is minimum.
The setting range is OFF, -40dB to -5dB. This function does not
work at “OFF”. Otherwise the level is maintained even if the Expression is minimum.
8. EXPRESSION - CURVE (S)
This is for setting how the value varies corresponding to the depressing angle of the Expression Pedal. 1 - 3 are curves for playing
while sitting on the bench, 4 - 5 are those for the playing while
standing. See the bottom right figure for details.
9. EXPRESSION - MONITOR
Displays the present Expression Value.
NOTE: The parameters by the names with (G) on the tail are for “Global”. These parameters will be recorded when set, and are common in each Combination Preset. (S) is for “System”. These
parameters will be recorded when set, and are common in each
Combination Preset, and it does not save to setup.
Value
NOTE: You can locate this page by pushing Foot switch while pressing
the [MENU/EXIT] button.
Degree
‹EXPRESSION PEDAL
5. EXPRESSION - MINIMUM LEVEL (G)
Sets the minimum level when the Expression pedal at its “back”
position. The setting range is OFF, -40db to 0db. “OFF” renders
Setting the Parameters
CUST. TW (CUSTom Tone-Wheels)
92
In this mode, you can regulate the tonal qualities of the virtual
tone-wheel generator, wheel by wheel.
The virtual tone-wheel generator consists of 96 different pitches,
where one wheel may correspond with plural notes and the “foot”
designation of the Drawbars.
The relation is complicated. For example, the middle C of 8' and
the C one octave lower of 4' use the identical wheel.
Wheel Set. These are called “CUSTOM TONE-WHEELS”.
The factory default gives a choice of B-3 “types”. You may create your own.
To locate this mode:
Press the [MENU/EXIT] button and display MENU, select PAGE
C by the [PAGE] button, and then press the [4] CUST. TW
button.
In this organ, you can save 2 types of settings per virtual Tone-
4
6
4
7
5
3
2
1
1. TONE-WHEEL SET
This is for selecting the Tone-Wheel set.
2. CUSTOM NUMBER
This is for selecting the “CUSTOM NUMBER” to use or compile. The “*” will be dis- INITIAL VALUE OF THE CUSTOM NUMBER
As the initial value, the typical setting is recorded to
played when the Tone-wheel parameters are changed from this Custom Number.
NOTE: This parameter is a Global Parameter. It is not recorded into the Combination Preset.
3. CUSTOM NAME
You can name the CUSTOM TONEWHEELS using up to 10 letters.
each Custom No. 1.
For example, “Real B-3”, a simulated original B-3 in
good condition, is in B-Type 1.
Move the cursor by the [PARAM] button and choose the letters by the [VALUE] button.
By pressing the [VALUE] button while holding down the [RECORD] button, it jumps to
the top of each letter type (space, 0, A, a).
The name set here, as well as the Tonewheel parameters below, will be deleted, if you do
not do the recording operation as explained on the next paragraph.
4. WHEEL NUMBER
Select the number of the wheel you want to adjust.
To select the Wheel Number, select the [VALUE] button, or slightly move the feet of the
Drawbar while depressing the key you want to regulate. (See the illustration.)
When the Wheel Number is selected, the level for the wheel (#5) is displayed.
How to select the WHEEL NUMBER
*#1
$OM%OM$2OMOwner’s Manual
93
5. LEVEL
This is for setting the volume of this wheel.
The setting range is -20 to 0dB. As you increase the value, the volume increases.
6. LEAKAGE WHEEL NUMBER
On this organ, you can produce the sound of each wheel: 61:6C to 91:8F# on the “fundamental” wheel: 01:1C to 60:5B; as Leakage Noise at each volume. (See the right figure.)
Concept of the level adjustment
Select the wheels to output as leakage noise together with the fundamental sound wheel
appearing on the left side of the display.
To select the Leakage Wheel Number, select it by the [VALUE] button or by slightly
moving the feet of the drawbar holding down the key you want to adjust.
7. LEAKAGE WHEEL LEVEL
This is for adjusting the volume of the selected leakage wheel.
Setting range is 0 to 127. However, depending on the situation, the volume may not rise
higher than a certain level, when increasing the value.
NOTE: These parameters are the Tonewheel parameter. If you do the recording operation of the
next page, it works commonly to the same Tonewheel Set (in this example, “BType1”) of
each Combination Preset.
Concept of the leakage noise
NOTE: When you operate these parameters, if you do not do the recording operation of the next
page, it is lost when you turn off the power.
Setting the Parameters
94
Record the Custom Tone-Wheels
The Tonewheel parameters (= 3 - 5 of the previous Section) are for
determining the Custom Number for recording.
1
Enter the Custom Name.
2
Press the [RECORD] button in the setting mode of the virtual
Tonewheel parameters.
The mode for selecting the Custom Number to be recorded will be
displayed.
3
Select the Custom Number to be recorded by the [PAGE] button.
4
It will be recorded when you press the [4] OK button.
The display will be as illustrated, while the recording is proceeded.
NOTE: To cancel recording, press the [MENU/EXIT] button.
*#1
$OM%OM$2OMOwner’s Manual
DEFAULT
95
In this mode, you can totally or partially recall the factory default settings.
To locate this mode:
Press the [MENU/EXIT] button for the MENU display, select PAGE D by the [PAGE] button,
and then press the [1] DEFAULT button.
4
5
6
1
2
3
To initialize each parameter, press the [PARAM] button and then [4] OK.
1. ADJUST PRESETS
Initializes the content of the Preset Keys [A<] and [B].
2. PRESETS
Initializes the contents of all Combination Presets.
3. GLOBAL
Initializes the Global Parameters such as Master tune or assignment of the Foot Switch.
4. LESLIE
Initializes the content of all Internal Leslie cabinets.
5. TONE WHEEL
Initializes the Custom Tonewheels.
6. ALL
Initializes all parameters of this organ.
If any unstable condition occurs on this organ system, initializing “all” sill usually clear the
problem.
NOTE: You can also totally initialize your organ by switching the Power ON while pressing and holding the [RECORD] button.
Setting the Parameters
SYSTEM
96
In this mode, you can set the SYSTEM PARAMETERS of this organ and the display information.
To locate this mode:
Press the [MENU/EXIT] button to display the MENU, select PAGE D by the [PAGE] button,
and then press the [2] SYSTEM button.
11
12
8
9
10
5
6
7
4
1
2
3
1. PEDAL PART - OUTPUT
This is for setting which jack to outputs the Pedal part.
B OTH
OTH: Outputs the Pedal part to all the sound output jacks.
PED
AL
PEDAL
AL: Outputs the Pedal part only to the PEDAL OUT jack.
2. PEDAL PART - REBOUND TIME
The Pedalboard sometimes sounds twice caused by the “rebound” which happens when
the keys are played staccato and released, depending on the condition of the sheet spring
used on it. This can be avoided by adjusting the “rebound time”.
The setting range is 1 - 128 x 1.4 msec. The initial value is 40 x 1.4 msec.
NOTE: If the rebound time is too long, it causes a sound delay.
3. PEDAL PART - MIDI MESSAGE
“*” is displayed while the Pedal part sound is output by the MIDI message from the PEDAL
MIDI IN jack.
4. DRAWBARS - CONTROL MODE
This sets the condition for activating the registrations with the Manual Drawbars.
A#/B:
The Drawbars are active only when the Preset Keys [A#] and [B] are selected,
same as the original B-3/C-3.
AL
WAYS:
ALW
The Drawbars are active regardless which Preset Keys are selected, same as the
XK-3.
5. - 12. VERSIONS
These are the versions of each software built in this organ.
These are only for displaying the version number.
*#1
$OM%OM$2OMOwner’s Manual
97
MIDI
*#1
$OM%OM$2OMOwner’s Manual
ABOUT MIDI
98
What is “MIDI”?
MIDI is an abbreviation of Musical Instrument Digital Interface.
MIDI is the musical instrument industry standard for exchanging performance information
between electronic musical instruments and a sequencer, effects, lighting, and sound
reiinforcement gear, etc.
The MIDI standard allows instruments made by different manufacturers to effectively communicate with each other.
Many types of data can be transmitted and received, including all performance information,
settings of parameters, and global commands.
MIDI terminals on this Organ
MIDI OUT
Sends Performance Information.
MIDI PEDAL IN
Receives the performance information of the Pedal part.
Receives only the note message and the setting is fixed at OMNI ON.
What the MIDI can do on your Organ
On this organ, the MIDI terminals are intended to do the following:
Πcontrol an external sound generator such as a synthesizer or sampler.
Πuse a MIDI Pedal board instead of the traditional Pedalboard.
™ Due to the exclusive electro-mechanical “Direct Analog Keying System”, it
is impossible to “play” this organ from a remote MIDI source, such as a
sequencer or MIDI controller.
*#1
$OM%OM$2OMOwner’s Manual
99
MIDI CHANNEL
MIDI has 16 “CHANNELS”. Information divided into 16 channels can transmit through one
MIDI cable.
The channel must match between the sender and the receiver. If not, the machines can not
“hear” what the other “says”.
MAJOR MIDI MESSAGE
The MIDI infomation is grouped into a channel message per each of the 16 channels and a
system message for all channels. There are more details in the MIDI IMPLEMENTATION
CHART.
CHANNEL MESSAGE
 NOTE ON / NOTE OFF
This data tells: which key (Note Number) is played, at what Speed (Velocity) and whether
played or released (Note On/Off).
The MIDI PEDAL IN jack on this organ receives only Note On/Note Off.
It does not recognize velocity commands.
 PROGRAM CHANGE
Switches the programs of External MIDI equipment.
 CONTROL CHANGE
Data will be sent corresponding to the action of the Expression Pedal, Foot Switch, etc.
SYSTEM MESSAGE
 SYSTEM EXCLUSIVE MESSAGE
This organ does not send/receive the system exclusive message.
MIDI
MIDI STRUCTURE
100
This organ has 3 “External Zones” on each of the Swell, Great and Pedalboards for
controlling the external MIDI equipment.
*#1
$OM%OM$2OMOwner’s Manual
CONTROLLING EXTERNAL MIDI EQUIPMENT
101
You can control external MIDI equipment with up to 3 zones per each of the Swell,
Great manuals and Pedalboard.
1. Connect as shown above.
Connect the MIDI OUT of this organ to the MIDI IN of the equipment you wish to control.
When the MIDI Pedal board is connected to the MIDI PEDAL IN jack, the performance is treated
the same as the traditional Pedalboard.
2. Set the parameters of each zone, and record it to the Combination Preset, as desired.
Read the next page “EX. ZONE (External Zone)” for setting each zone.
NOTE ON THE SOUNDING POINT
The External Zones sound at a deeper point of the
key than the Drawbar tones.
This is for outputting the velocity info. to the External Zone.
This is due to the extra velocity-sensing MIDI keyboard contact that lies below the direct analog keying system.
MIDI
EX. ZONE (EXternal ZONE)
102
To control external MIDI equipment, ranges on the keyboard of this organ are assigned. They are called “External
Zones”.
To locate this mode:
Press the [MENU/EXIT] button and display MENU, select Page
C by the [PAGE] button, then press [1] EXZONE.
A MIDI Pedalboard connected to the MIDI PEDAL IN
can control the MIDI equipment by the Pedal EXTERNAL
ZONE.
1
2
3
4
5
6
7
There are 3 External Zones (SL1, 2, 3) for the Swell manual, 3 (GR1, 2, 3) for the Great manual
and 3 (PD1, 2, 3) for the Pedalboard.
1. SWITCH
This switch “turns on” the selected External Zone.
2. MIDI CHANNEL
This is for choosing the External Zone’s transmitting MIDI channel.
The range is 1 - 16, and OFF.
3. MAP - LOW
4. MAP - HIGH
These set the playing range of the chosen External Zone on each of the Swell, Great manuals and
Pedalboard.
Set the lowest note at LO and the highest one at HI. To forbid sending note data, set the HI
parameter to “OFF”.
NOTE:
For 3 and 4, you can set the value by pressing the [RECORD] button, while holding down the
desired note on the manual (or pedalboard).
Owner’s Manual
8
9
10
11
103
15
12
13
14
5. PROGRAM - BANK MSB
6. PROGRAM - BANK LSB
7. PROGRAM - PROGRAM CHANGE
These are for setting the Bank Select and the Program Change data to be transmitted by this zone.
Please consult the users guide/manual for your specific piece of outboard gear that you wish to control
for the exact combination of commands that allow bank and program change.
You can choose 0 - 127 in the Bank MSB and the Bank LSB, and 1 - 128 in the Program Change.
8. NOTE - OCTAVE
NUMBER BASE
Some MIDI modules map their presets
from 0 - 127, and some from 1 - 128. If
your instrument does not respond to the
exact number of program change, you
may need to decrease the program
change number here by the value [1].
This is for selecting the octave to be transmitted by this zone. The octave that is transmitted may be set
to be different than the octave that you may be playing.
9. NOTE - VOLUME
This is for setting the volume (= Control Change #7) of this zone. However, the set value will be null,
if the CC# (item #14) is at “7.VOL”.
10.NOTE - PAN
This is for setting the Pan (= Control Change #10) of this zone.
MIDI
104
1
2
3
4
5
6
7
11. NOTE - VELOCITY
This is for setting the Velocity Curve to send to this zone.
The setting range is OF, 1 - 4. The velocity of OF is fixed at 100. At 1 - 4, the higher the value
increases, the higher velocity is transmitted regardless how the key is played.
NOTE:
As the Pedalboard of this organ has no velocity sensing function, the velocity of PD1 - 3 is
fixed at OF.
12.EXPRESSION - MINIMUM
13.EXPRESSION - MAXIMUM
These set the range of expression to “compress” to send to this Zone.
If the expression pedal of this organ is fully returned the organ will still be heard.
With many types of external sound gear, the volumes do not react the same. This parameter allows
a smooth and equal flow in the expression pedal.
You can select 0 - 63 by MIN, and 64 - 127 by MAX.
14.EXPRESSION - CONTROL NUMBER
This is for setting the MIDI continuous Control Number of the Expression Pedal.
Depending on your external equipment, it may react to CC#7 (Volume) or CC#11 (Expression).
This parameter allows you to make that choice.
15.MESSAGE - DAMPER
This is for setting the transmission of Damper (Control Change #64) to this zone using the Foot
Switch on the Expression Pedal.
The message is sent at ON, and is not at OFF.
NOTE:
All the parameters in these modes are Preset Parameters. They can be recorded to the Combination Presets. See the Appendix for details of the Preset Parameters.
*#1
$OM%OM$2OMOwner’s Manual
8
9
10
11
105
12
15
13
14
PANIC FUNCTION and PARAMETER RELOAD
If any problem happens in the MIDI system, it may cause ciphering (sticking notes). Immediately after
this organ and an external MIDI equipment are connected, a glitch or “MIDI hangup” may occur.
If this occurs, press PAGE [S] and [T] at the same time. [All Note Off] and [Reset All Controller]
will be transmitted to all External Zone MIDI channels (Panic Function) and then all the EXTERNAL
ZONE settings will be re-sent.
MIDI
106
*#1
$OM%OM$2OMOwner’s Manual
107
SAVE THE SETUP
*#1
$OM%OM$2OMOwner’s Manual
SAVE YOUR SETUP
108
On this organ you can save the setting of each Parameter as a file, into a
CompactFlash™ card (hereinafter “CF card”) up to 99 files.
How to access the CF card slot
B-3 mk2, C-3 mk2
B-3P mk2
Turn the screws with the #2 Phillips screw driver and take off the
HAMMOND plate on the back of the organ.
Turn and remove the knob bolts with a coin from the back of the
organ. Then take off the rear panel.
About the CF Card
Eject Button
CF CARD YOU CAN USE
The manufacturer recommends genuine Hammond 65971-02128
as your CF card.
Please consult URL: http://www.hammondsuzuki.com before you
try to use other cards on the market.
CF CARD SLOT
1. First please read the label on the CF card carefully and insert
it correctly.
2. To take out the card, push the EJECT button on the right hand
side of the slot.
3. Don’t eject the card or switch the power off during initializing
or setting it up.
*#1
THE CARD CAPACITY AND CONTENT TO BE
SAVED
The CF card can save:
Œ
Œ
Œ
Œ
Œ
Œ
Combination Presets
Global Parameters
Custom Tonewheels
Leslie Cabinets
Adjust Presets [A<], [B]
Temporary Parameters
Also, this card can save/read out all of them as a whole by the unit
called “SET-UP”. The capacity of one SET-UP is approximately
44 KB.
$OM%OM$2OMOwner’s Manual
INITIALIZE THE CF CARD
109
The CF CARD must be “INITIALIZED” first (= before you use it). Perform the
following, step by step, to do the initializing operation.
™This operation erases all data in the CF card.
1
4
Insert the CF card into the slot.
Press [4] CF FORM.
The FORMAT mode is displayed.
2
5
Press the [4] OK button.
Press the [MENU/EXIT] button.
3
The Confirmation message is displayed.
6
Press the [4] YES button.
Select PAGE D by the [PAGE] button.
The initialization starts and takes only a few seconds.
NOTE:
To cancel initializing, press the [3] NO button.
7
To return to the PLAY mode, press [PLAY].
Save the Setup
SETUP PROCEDURES
110
Save or Load the SET UP to/from the CF card in the SETUP mode. In this mode, you
can do all the operations except the initialization of the CF card.
To come to this menu:
Press the [MENU] button to display the MENU, select PAGE D by the [3] SETUP button.
How to read the Display
Setup Name
This indicates there is another
SETUP file above (or below).
Rename
Load
Save
Delete
Save the SETUP
1
4
Check that the CF card is correctly inserted.
2
Go to the SETUP mode.
WHAT DOES THIS MEAN?
CF is not ready
Press the [2] SAV button.
SAVE starts.
The CF card is not correctly inserted.
3
5
A temporary name is put to the saved SETUP “Setup xx” automatically.
Select the SET UP NAME “NewSetup” by the [PAGE]
button.
NOTE:
“NewSetup” means a fresh save. If you select an
existing SET UP NAME, it will be deleted and written over.
*#1
$OM%OM$2OMOwner’s Manual
111
Change the SETUP name
1
4
Select the SETUP file you want to change the name of.
2
Move the cursor to the right end by the [PARAM] button.
[ENT] will be displayed.
5
Press the [3] NAM button. This is the SETUP NAME INPUT mode.
3
Press the [4] ENT button.
The SETUP NAME will be changed.
Input the new SET UP NAME.
[PARAM] BUTTON
Move the cursor.
You can use up to 16 letters.
[VALUE] BUTTON
Choose the letters by this.
You can use Large and small characters, digits and signs/
symbols.
If you press this button, holding down the [RECORD] button, you can move to the head/the first letter of each type
(= space, 0, A, a).
Save the Setup
112
Loading the SETUP
™ After the operation, the settings already in
this organ will be replaced by the newly
loaded SETUP.
How to delete the SETUP
1
Check the CF card is correctly inserted.
2
1
Check the CF card is correctly inserted.
Navigate to the SETUP mode.
3
2
Navigate to the SETUP mode.
Choose the SETUP file you want to delete by the [PAGE] button.
3
4
Choose the SETUP file to load by the [PARAM] button.
Press the [4] DEL button.
The Confirmation message will be displayed.
4
5
Press the [1] LOD button.
The SETUP will be loaded in a few seconds.
Press the [4] YES button.
The Delete operation starts.
NOTE:
*#1
$OM%OM$2OMOwner’s Manual
To cancel the delete action, press the [3] NO button.
113
FREQUENTLY ASKED
QUESTIONS
*#1
$OM%OM$2OMOwner’s Manual
114
UTILIZING NEW FUNCTIONS & FEATURES
‹ How to control the leakage sound:
Š The leakage volume of the whole tone-wheel set currently selected is adjustable by the LEAKAGE Parameter in the DRAWBAR Function mode. (P. 72 #2)
Adjustment of the leakage interval and or volume per each wheel can be made by using the Custom
Tone-wheel. (P. 92)
‹ How to turn on PEDAL SUSTAIN:
Š Press [PLAY] and display “P.SUS”, then select “ON” by [VALUE]. The length of sustain effects is
controlled by the SL parameter in the DRAWBAR function mode. (P. 73 #8)
‹ How to record other parameters than drawbars to the preset keys:
Š The memory/record operation on this organ also enables you to record various parameters along with the
Drawbar registrations. To set the parameter to call when the preset key is selected, set the parameters on
the P. LOAD page in the PRESET function mode. (P. 76)
‹ How to see the actual values of a preset:
Š In case the physical location of the controller and the actual value do not exactly match when you call a
preset such as the [VIBRATO] tablet, you can display the actual value by operating the controller holding down the [PLAY] button. (P. 78) The actual Drawbar registration is displayed in PLAY mode.
‹ How to locate each function mode easily?
Š You can “short-cut” to each function mode by moving some controllers (e.g. tablets, knobs) while pressing the [MENU/EXIT] button.
‹ How to adjust the Drawbar settings while playing with the Preset C< - A:
Š To temporarily adjust the Drawbar settings while you are playing with the preset keys [C<] - [A], operate
Drawbars holding down the [PLAY] button. (P. 52)
‹ Relation between the built-in Leslie effect and the external Leslie speaker:
Š If no Leslie speaker is connected or headphones are used while a Leslie speaker is connected, the builtin Leslie effects are added to both (L & R) channels.
Š If a Leslie speaker is connected, the built-in Leslie effects are added only to the L channel.
‹ How to avoid adding Leslie effects on the Pedal part:
Š The Pedal Part sound is independently output at the PEDAL OUT jack. The built-in Leslie effects,
Reverb, Tube Buffer do not function at this jack.
By connecting the PEDAL OUT jack and the PA equipment and setting the SYSTEM-PEDAL PART
OUTPUT parameter to “PEDAL”, the manual part and the pedal part are separately output to the Leslie
speaker and the PEDAL OUT jack respectively (P. 96 #1).
‹ How to change the motion of the built-in Leslie effect when the Leslie mode
switch is set at “STOP”.
Š The default setting of the built-in Leslie effects on this organ is to bypass (thru) when the Leslie mode
switch is set at “STOP”, so you can enjoy the sound engine’s original sound.
To get the effect of the rotor stop of the Leslie speaker at this time, set the STOP mode at “STOP” in the
LESLIE function mode. (P.86 #20)
‹ How to totally cut off the sound when the expression pedal is returned.
Š The characteristic of the Expression Pedal can be freely changed.
To turn off the sound completely when the Expression Pedal is returned, set all the minimum level, limit
LF, limit HF at “OFF” in the CONTROL function mode. (P. 91 #5, #6, #7)
*#1
$OM%OM$2OMOwner’s Manual
TROUBLESHOOTING
115
‹ Malfunction of the buttons, the keys, etc.
Š Turn off the POWER switch once, then turn it on again. If this procedure is not successful, turn off the
POWER switch. While pressing the [RECORD] button, turn the POWER switch on again. (Note that in this
case, all parameters return to their factory-preset status.)
‹ No sound is produced when the keys are pressed.
Š The MASTER VOLUME is at the minimum setting.D
Adjust the volume with the MASTER VOLUME control. (P. 22 #25)
Š No Preset key is selected. D
Select a Preset key.
Š A plug is inserted to the HEADPHONE jack. D
While a plug is inserted here, the Leslie speaker is disabled.
‹ The Foot Switch does not work.
Š The Foot Switch settings are not correct.D
Reset the Foot Switch correctly in the CONTROL mode. (P. 91 #4)
‹ The sound does not come out immediately after switched on.
Š A Vacuum Tube circuit is mounted in this organ. It takes approximately 10 to 20 seconds after switched on
before you will hear the sound.
‹ The sound is not distorted if the OVERDRIVE knob is turned.
Š When the Overdrive Expression is at “EX-OD”, it does not distort if the Expression pedal is low. In such a
case, increase the Expression pedal, or set the Overdrive Expression at “OD-EX” if you want to distort
regardless of the Expression value. (P. 80 #1)
‹ Leslie speaker sound is distorted.
Š If the sound is distorted regardless of the position of the volume of the Leslie speaker when you are using a
Leslie adapter (such as the 11 pin/6 pin converter), the power of this organ seems to be so large that the sound
is distorted inside the Leslie adapter. In such a case, return the [MASTER VOLUME] knob to 10 o’clock
position.
‹ The rotor of the external Leslie speaker does not stop, if the Leslie mode is switched
to [STOP].
Š Some Leslie Speaker models do not [STOP]. [STOP] is possible on 2101/2102, 122XB, 971 and 3300 (current models).
‹ Audio is interrupted when a Combination Preset is selected.
Š Between the Combination Presets with different Tonewheel Settings, the sound will be cut off while the
Tonewheel Settings are switched.
Š The sound is once cut between the presets with different key mode (MONO/POLY) on the Pedal part, for
switching the sound algorithm.
‹ There is excessive MIDI latency compared to the organ (Drawbar) sound.
Š The position of the key contact for MIDI send is deeper than that of the multi-contacts for Drawbars.
Š There are too many zones to send. D
Turn [OFF] the switches of unnecessary external zones.
‹ No sounds of Pedal part from the headphones.
Š PEDAL OUTPUT set at “PEDOUT”. D
Set the PEDAL OUTPUT at “BOTH” when using the headphones (P. 96 #1).
‹ Manual contact does not work well.
Š The multi-contacts used for the manuals on this organ is designed to be used for a long time. Refer for the
contact refreshing procedures to the “Instruction for keyboard contact cleaning function”.
And, if all the contact points have been worn out and the problem is not solved any longer by refreshing the
contacts, please consult your local dealer or store for further maintenance.
Frequently Asked Questions
DAILY CARE AND MAINTENANCE
116
‹ How to care for your organ:
Š When you want to clean the keys or cabinets, use only a soft cloth. If they are extremely dirty, use
a barely damp cloth with a neutral detergent. Never apply alcohol, thinner or benzine.
‹ There is no MIDI IN jack for the manual part;
Š Because of electro-mechanical direct analog keying mechanism is adopted on this organ, the
information of each of the multi-contacts is not defined with a MIDI message.
‹ The Leslie Speed Switch cord is too long:
Š A rather long cord is provided for the Leslie Speed Switch, so the player can move the unit as
desired. If it is longer than desired, please bind and fix the extra portion with a wire clamp.
‹ Do I need to oil my organ?
Š There is no part needing oiling on your organ.
*#1
$OM%OM$2OMOwner’s Manual
117
APPENDIX
*#1
$OM%OM$2OMOwner’s Manual
MIDI IMPLEMENTATION CHART
118
[Hammond Console Organ]
B-3 mk2
Model:
Function
Default
Basic
Changed
Channel
Default
Mode
Messages
Altered
Note
Number
: True Voice
Note ON
Velocity
Note OFF
Key's
After
Ch's
Touch
Pitch Bender
0, 32
7
10
11
Control
64
Change
121
MIDI Implementation Chart
Transmitted
Off
1 - 16
3
X
*****
12 - 120
*****
O
X
X
X
X
O
O
O
O
O
O
Program
O
Change
: True #
*****
X
System Exclusive
: Song Position X
System
: Song Select
X
Common
: Tune
X
: Clock
System
X
Real Time : Commands
X
: Local On/Off
X
Aux
: All Notes Off
O
Messages : Active Sense O
: Reset
X
Mode 1:
OMNI ON, POLY
Mode 3:
OMNI OFF, POLY
*#1
Recognized
Omni On
*****
1
X
X
36 - 60
36 - 60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
O
X
Mode 2: OMNI ON, MONO
Mode 4: OMNI OFF, MONO
Date: 9-June-2008
Version: 1.0
Remarks
Tx: External Zones
Rx: Pedal Part
Bank Select MSB, LSB
Volume
Pan
Expression
Hold 1
Reset All Controllers
0 - 127
$OM%OM$2OMOwner’s Manual
O: Yes
X: No
PARAMETERS
119
Global Parameters
Global Parameters
Category
Parameter
Data Range
Bank Name (8 Characters)
Tune
Default
each bank
Transpose
-6 - 0 - 6
0
Master Tune
430 - 440 - 450
440
Off, -40dB - -0dB
Off, -60dB - -0dB
-27dB
-20dB
Expression Min. Level
Min. Limit LF
Min. Limit HF
-30dB
Curve
00 - 04 (1 - 5)
Foot
Switch
Mode
Off
Leslie C/T (alternate)
Leslie C/T (alternate)
Leslie C/T (momentarily)
Spring Shock
Delay Time
Reverb Depth
Motor
Control
Bend Time Down
Bend Time Up
Bend Amplitude
Link Great-Pedal (G-P)
0.1 - 9.9s
0.1 - 9.9s
Off / On
Off / On
5.0s
1.0s
On
Off
Manual Bass (MANBS)
Off / On
Off
External Zone Swell (EXT-S) Off / On
Off
External Zone Great (EXT-G) Off / On
Reverb, Equalizer (RV/EQ)
Off / On
Off
Off
Leslie, Vibrato (ANI/OD)
Off / On
Off
Registration Swell (SWELL)
Off / On
On
Registration Great (GREAT)
Drawbar (DRAWB)
Off / On
Off / On
On
Off
Percussion (PERCUS)
Off / On
Off
Combi.
Preset
Load
1
Appendix
120
Preset Parameters
Category
Parameter
Swell
Drawbar
Effect
Category
Combination Preset Parameters
Leslie Mode
Leslie Stop Mode
Leslie Cabinet
Vibrato On Swell
Vibrato Mode
Vibrato Rate
Vibrato Tremolo
Vibrato Cho. Emphasis
Vibrato Depth V1
Vibrato Depth V2
Vibrato Depth V3
Vibrato Depth C1
Vibrato Depth C2
Vibrato Depth C3
OD Drive Level
OD Exp. Ctrl
OD Bias
Buffer Amp
Buffer Bias
EQ Bass Gain
EQ Mid Freq
EQ Mid Gain
EQ Treble Gain
EQ Tone Control
Reverb Type
Reverb Depth
Reverb Time
Reverb Delay Feedback
Reverb Delay Time
Leslie On Reverb
*#1
Data Range
Choral, Stop, Tremolo
Through / Stop
1-8
Off / On
V1 - C3
6.1 - 7.25Hz
0 - 15
0-9
0 - 15
0 - 15
0 - 15
0 - 15
0 - 15
0 - 15
0 - 63
Off / On
-32 - +31
Off / On
-32 - +31
-9 - 0 - +9 dB
180Hz - 2.9kHz
-9 - 0 - +9 dB
-9 - 0 - +9 dB
-9 - 0 - +9
Room 1
Room 2
Live House
Hall 1
Hall 2
Church
Plate
Spring
Delay
Pannning Delay
Reverb + Delay
P. load
ANI/OD
Combination Preset Parameters
Parameter
Manual
Bass
External
Zone
ANI/OD
ANI/OD
EQ/REV
EQ/REV
0 - 15
0 - 31
0 - 96%
4.7 - 1000ms
Off / On
$OM%OM$2OMOwner’s Manual
Data
Manual Bass On
Off / On
Manual Bass Range High 1C - 6C
Switch
Channel
Bank MSB
Bank LSB
Program Change
Octave Shift
Volume
Pan
Vel. Curve
Exp. Min
Exp. Max
Exp. CC#
Tx. Damper
Key Range Low
Key Range High
Off / On
1 - 16, Off
0 - 127
0 - 127
1 - 128
-2 - 0 - +2
0 - 127
L64 - C - R63
Off, Normal - Easy
0 - 63
64 - 127
7, 11
Off / On
1C - 5B
1C# - 6C, Off
P. load
MANBS
EXT
(Swell 1 Swell 3)
EXT and
G-P
(Great 1 Pedal 3)
121
Category
Combination Preset Parameters
Parameter
Swell/
Great
Drawbar
Voice
Percussion
Voice
Swell
Drawbars
Data
Tone-wheel Set
B-Type
Mellow
Leakage Level
Fold Back Low
Fold Back High
Percussion On
Decay Fast
Soft
Harmonic
Level Soft
Level Normal
Decay Fast
Decay Slow
Drawbar 1' Cancel
Drawbar Level
16'
5 1/3'
8'
4'
2 2/3'
2'
1 3/5'
1 1/3'
1'
0 - 127
1C - 2C
4G - 5C
Off / On
Off / On
Off / On
Second / Third
1 - 16
1 - 16
1 - 15, Cont.
1 - 15, Cont.
Off / On
0, -3dB
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
Category
Great Preset Parameters
P. load
DRAWB
PERCUS
Parameter
16'
Great
Drawbars 5 1/3'
8'
4'
2 2/3'
2'
1 3/5'
1 1/3'
1'
Data
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
Off / On
Great
Drawbar
Effect
Vibrato On Great
Vibrato Tablet Great
Great
Great and Pedal
Pedal
Drawbar
Voice
Tone-wheel Set
Normal
Muted
Synth 1
Synth 2
Drawbar Attack
Slow Attack
No Click
Soft Click
Normal Click
Max Click
SWELL
Pedal
Drawbars
Pedal
Sub
Drawbars
Sustain On
Sustain Length
Pedal Key Mode
Decay Length
Off / On
1-5
Mono / Poly
1 - 5, Cont.
16'
8'
0-8
Normal 16' - 16'
Normal 16' - 5 1/3'
Normal 16' - 8'
Normal 16' - 4'
Normal 16' - 2 2/3'
Normal 16' - 2'
Normal 16' - 1 3/5'
Normal 16' - 1 1/3'
Normal 8' - 8'
Normal 8' - 4'
Normal 8' - 2 2/3'
Normal 8' - 2'
Normal 8' - 1 3/5'
Normal 8' - 1 1/3'
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
0-8
P. load
GREAT
ANI/OD
DRAWB
and G-P
G-P
DRAWB
and G-P
Appendix
122
Leslie Parameters
Category
Leslie Parameters
Parameter
Cabinet
Data Range
Name
(10 Characters)
Slow Speed Horn
Slow Speed Bass
Fast Speed Horn
Fast Speed Bass
Rise Time Horn
Rise Time Bass
Fall Time Horn
Fall Time Bass
Brake Time Horn
Brake Time Bass
Volume Horn
Volume Bass
Mic. Angle
Mic. Distance
Horn Character
Amplifier
Speaker
0, 24 - 318rpm
0, 24 - 318rpm
0, 375 - 453rpm
0, 375 - 453rpm
0.2 - 5.0s
0.5 - 12.5s
0.2 - 5.0s
0.5 - 12.5s
0.2 - 5.0s
0.5 - 12.5s
-12 - 0dB
-12 - 0dB
0 - 180deg
0.3 - 2.7m
Flat, Mid, Deep
Solidstate, Tube
Rotary Small
Rotary Large
Stationary
System Parameters
Category
System Parameters
Parameter
Data Range
Default
Ext.
Leslie
Horn
Mellow / Flat
Mellow
Audio
Pedal
Both / Pedal Out
Both
Key Scan
Pedal Rebound
1-128
4
Display
Lock
Off / On
Off
*#1
$OM%OM$2OMOwner’s Manual
SPECIFICATIONS
Sound Generator
Swell and Great
DTW1 Digital Tone-Wheels
Pedal
VASE III
Polyphony
Swell and Great
Full
Pedal
8
Keyboard
Swell and Great
61-keys (Multi Contact for Drawbars
and Rubber Contact for MIDI)
Direct Analog Keying
Water Fall type
Pedal (except B-3P mk2)
25-keys
Radial Flat type
Preset Key
Swell and Great
12-keys (Mechanical Latch)
Harmonic Drawbars
Swell and Great
9 Pitches, 2 sets per keyboard
B-type/Mellow
Pedal
2 Pitches,
Muted/Normal/Synth 1/Synth 2
Percussion
Tablets
On, Harmonic Selector, Decay,
Volume
Adjustable
Decay (Fast, Slow)
Level (Soft, Normal)
Effects
Internal Leslie
Advanced Digital, 2 Rotors
Vibrato and Chorus
Digital Scanner
Swell On, Great On
V1, V2, V3, C1, C2, C3
5 Speeds (6.10 - 7.25Hz)
Tremolo, Emphasis, Depth
Pre-amp
Vacuum tubes
(12AU7 for Overdrive and 12AX7
for Buffer)
Coupler
Manual Bass
Combination Presets
Common
5 banks
Swell
9 Presets
Great and Pedal
9 Presets
Switchable: Link/Independent
Pedal
Controllers
Switches
Power On / Off
Motor Control
Rotary Controllers
Master Volume
Overdrive
Bass
Treble
Reverb
Foot Controller
Expression Pedal (with foot
switch) except B-3P mk2
Display
20-characters, 2 lines
with 9 control switches
Storage
CompactFlash card slot
MIDI
Zones
3 (Swell), 3 (Great), 3 (Pedal)
Connections
AC Inlet
MIDI Pedal In, MIDI Out
Leslie Switch, Main/Echo
Switch
Effect Send, Return
Line In L, R
Line Out L, R
Pedal Out
Headphones
11-pin Leslie Main, Echo
Expression Pedal (B-3P mk2
only)
Pedalboard (B-3P mk2 only)
123
Dimension
B-3 mk2
console only:
123(W) x 73(D) x 97(H)cm
48”(W) x 29”(D) x 38”(H)
with music rack, bench and
pedalboard:
123(W) x 126(D) x 117(H)cm
48”(W) x 50”(D) x 46”(H)
C-3 mk2
console only:
125(W) x 73(D) x 97(H)cm
49”(W) x 29”(D) x 38”(H)
with music rack, bench and
pedalboard:
125(W) x 126(D) x 117(H)cm
49”(W) x 50”(D) x 46”(H)
B-3P mk2
on stand:
123(W) x 73(D) x 117(H)cm
48”(W) x 29”(D) x 38”(H)
Weight
B-3 mk2
console only:
95 kg, 209 lbs
with music rack, bench and
pedalboard:
132 kg, 291 lbs
C-3 mk2
console only:
107kg, 236 lbs
with music rack, bench and
pedalboard:
144 kg, 318 lbs
B-3P mk2
console only:
65 kg, 143 lbs
with stand:
85 kg, 187 lbs
Accessory
B-3 mk2, C-3 mk2
Pedalboard, Bench
Music Rack
CompactFlash card
Leslie Speed Switch
AC Cable
Hexagonal Wrench
B-3P mk2
Stand, Music Rack
Expression Pedal
CompactFlash card
Leslie Speed Switch
AC Cable
Hexagonal Wrench
Equalizer
3 Bands and Tone Control
Reverb
11 Programs
with Leslie on Reverb
Sustain
5 Lengths (Pedal)
Appendix
FACTORY PRESETS
124
Key
C
C<
D
D<
E
F
F<
G
G<
A
A<
B
Key
C
C<
D
D<
E
F
F<
G
G<
A
A<
B
Key
C
C<
D
D<
E
F
F<
G
G<
A
A<
B
Registration
N/A
00 5320 000
00 4432 000
00 8740 000
00 4544 222
00 5403 000
00 4675 300
00 5644 320
00 6876 540
32 7645 222
Drawbars A<
Drawbars B
Swell Keyboard
Tone Quality
Cancel
Stopped Flute
Dulciana
French Horn
Salicional
Flutes 8' & 4'
Oboe Horn
Swell Diapason
Trumpet
Full Swell
Adjust
Adjust
Registration
N/A
88 8000 000
88 8800 000
88 8800 008
80 0008 888
80 0800 000
88 8000 008
88 8880 000
88 0888 080
88 8888 888
Drawbars A<
Drawbars B
Swell Keyboard
Tone Quality
Cancel
Jimmy 1
Power
Jimmy 2
Squabble
Walter
Groove
Pop
Jackie
All Nine
Adjust
Adjust
Registration
N/A
00 8740 000
00 8408 004
00 8080 840
08 8800 880
60 8088 000
00 4685 300
60 8807 006
00 6888 654
76 8878 667
Drawbars A<
Drawbars B
Swell Keyboard
Tone Quality
Cancel
French Horn 8'
Tibias 8' & 2'
Clarinet 8'
Novel Solo 8'
Theatre Solo 16'
Oboe Horn 8'
Full Tibias 16'
Trumpet 8'
Full Theatre Brass 16'
Adjust
Adjust
*#1
1: Liturgic
Loudness
N/A
pp
ppp
mf
pp
p
mf
mf
f
ff
N/A
N/A
Key
C
C<
D
D<
E
F
F<
G
G<
A
A<
B
Registration
N/A
00 4545 440
00 4423 220
00 7373 430
00 4544 220
00 6644 322
00 5642 200
00 6845 433
00 8030 000
42 7866 244
Drawbars A<
Drawbars B
Great Keyboard
Tone Quality
Cancel
Cello
Flute & String
Clarinet
Diapason, Gamba and Flute
Great, no reeds
Open Diapason
Full Great
Tibia Clausa
Full Great with 16'
Adjust
Adjust
Registration
N/A
83 8000 000
00 8800 000
84 8000 000
82 8000 000
80 8000 000
85 8000 000
00 8840 000
84 8010 000
00 8886 540
Drawbars A<
Drawbars B
Great Keyboard
Tone Quality
Cancel
Jimmy 1 Bass
Accomp.
Jimmy 2 Bass
Squabble Bass
Smooth Bass
Groove Bass
Pop Accomp.
Fat Bass
Full Accomp.
Adjust
Adjust
2: Jazz
Key
C
C<
D
D<
E
F
F<
G
G<
A
A<
B
3: Theatre
Key
C
C<
D
D<
E
F
F<
G
G<
A
A<
B
Registration
N/A
00 4545 442
00 4432 000
00 4800 000
00 2500 234
00 6554 322
00 5642 200
00 7656 311
00 8030 000
84 7767 666
Drawbars A<
Drawbars B
$OM%OM$2OMOwner’s Manual
Great Keyboard
Tone Quality
Cancel
Cello 8'
Dulciana 8'
Vibraharp 8'
Vox 8' & Tibia 4'
String Accomp. 8'
Open Diapason 8'
Full Accomp. 8'
Tibia 8'
Bombarde 16'
Adjust
Adjust
Loudness
N/A
mp
mp
mf
mf
f
f
ff
f
fff
N/A
N/A
125
Key
C
C<
D
D<
E
F
F<
G
G<
A
A<
B
Registration
N/A
68 8000 000
88 8800 000
85 7303 000
88 8888 888
88 8888 080
77 7331 000
80 8808 006
88 6000 008
87 8878 668
Drawbars A<
Drawbars B
Swell Keyboard
Tone Quality
Cancel
The Gnome (Swell)
Highway Star (Swell)
Born To Be Wild (Swell)
Telstar (Swell)
HM Soloist (Swell)
Funky Up (Swell)
Full Tibias (Swell)
Groove 2 (Swell)
Theatre Brass (Swell)
Adjust
Adjust
4: ShowCase
Key
C
C<
D
D<
E
F
F<
G
G<
A
A<
B
Registration
N/A
66 6666 888
00 5504 004
00 5414 004
00 5678 763
88 8000 000
00 6600 000
00 8630 000
00 8855 000
84 7767 666
Drawbars A<
Drawbars B
Great Keyboard
Tone Quality
Cancel
The Gnome (Great)
Highway Star (Great)
Born To Be Wild (Great)
Telstar (Great)
HM Soloist (Great)
Funky Up (Great)
Full Tibias (Great)
Groove 2 (Great)
Theatre Brass (Great)
Adjust
Adjust
This Bank introduces you this organ's advanced features.
Each Preset of this Bank calls out various parameters other than Drawbar registration, such as Leslie, Overdrive.
Swell Keyboard
Key Registration
Tone Quality
C N/A
Cancel
C<
D
D<
E
F
F<
G
G<
A
A< Drawbars A< Adjust
B
Drawbars B Adjust
5: User
Great Keyboard
Key Registration
Tone Quality
C N/A
Cancel
C<
D
D<
E
F
F<
G
G<
A
A< Drawbars A< Adjust
B
Drawbars B Adjust
Appendix
126
*#1
$OM%OM$2OMOwner’s Manual
SERVICE
127
Hammond maintains a policy of continuously improving and upgrading its instruments and therefore reserves the
right to change specifications without notice. Although every attempt has been made to insure the accuracy of the
descriptive contents of this Manual, total accuracy cannot be guaranteed.
Should the owner require further assistance, inquiries should first be made to your Authorized Hammond Dealer.
If you still need further assistance, contact Hammond at the following addresses:
In the United States Contact:
In Europe contact:
All other countries contact:
HAMMOND SUZUKI USA, Inc.
733 Annoreno Dr.
Addison, IL 60101
UNITED STATES
HAMMOND SUZUKI EUROPE
B.V.
IR. D.S. Tuynmanweg 4A
4131 PN Vianen
THE NETHERLANDS
HAMMOND SUZUKI Ltd.
25-11, Ryoke 2 Chome,
Naka-ku, Hamamatsu
430-0852 (Shizuoka)
JAPAN
Website:
www.hammondorganco.com
E-mail: [email protected]
Website: www.hammondsuzuki.com
Website: www.suzuki-music.co.jp
Technical materials are available and can be obtained by mailing a request to the appropriate address listed above
marked ATTENTION: SERVICE DEPARTMENT.
Manufacturer:
SUZUKI MUSICAL INSTRUMENT MFG. CO., Ltd.
25-12, Ryoke 2 Chome, Naka-ku,
Hamamatsu 430-0852 (Shizuoka)
JAPAN
*#1
$OM%OM$2OMOwner’s Manual
HAMMOND SUZUKI, LTD., Hamamatsu, Japan
Printed in Japan
00457-40154
V1.00-081105
INSTRUCTION
Please keep this instruction wit h the attached hex wrench.
FOR KEYBOARD CONTACT CLEANING FUNCTION (B-3mk2,C-3mk2)
B-3 KEY CONTACT CLEANING
CLEANING INSRUCTIONS
The B-3/C-3 utilizes multi-contact manuals to produce the drawbar and
key click sounds the same way as the original B-3. There are a total of
1220 gold-plated contacts in both manuals. After some extended period of time,
the contacts will get dirty and will need to be cleaned.
This condition can be recognized by an increase of key-click noise and
intermittent/scratchy sounds from the drawbars. After this condition occurs,
the following key-contact procedure needs to be followed.
PROCEDURE OVERVIEW
Please refer to the picture below.
There are ten bus bars that cover the distance between key 1 and key 61.
One end of the bus bars are clamped in the Bus Bar Shifter Module.
The Hex wrench is inserted into the hex opening in the center of the module.
Rotating the Hex wrench one complete turn will shift the bus bars through
both the right and left limits.
Step 1. Remove two(2) big screws, and the wood panel. (see above picture)
Step 2. Locate the adjustment hole behind the BASS knob as shown below.
(see left picture below)
Step 3. Insert the hex wrench and rotate slowly until the shifter cam hole is located.
Step 4. Turn the wrench clockwise slowly until turning pressure increases if the wrench
turns easily at first. After pressure increases, turn an additional 15 degrees.
Step 5. If turning pressure is high initially, then only turn the wrench 15 degrees and stop.
Step 6. Remove the wrench and check for key noise. If the noise is gone, the contact has
been cleaned successfully.
Marking
for Lower manual
for Upper manual
15°
°
Bus bar
Wood panel
15
Leaf contact
big screws
Lower manual
Bus bar shifter module
Upper manual
(see right picture above)
Hex wrench
Step 1. Locate the upper manual adjustment hole and insert the hex wrench
until the shifter hole is located.
Step 2. Follow steps 3 to 5 above.
INSTRUCTION (B-3mk2) 00457-40110 0810
INSTRUCTION
Please keep this instruction wit h the attached hex wrench.
FOR KEYBOARD CONTACT CLEANING FUNCTION (B-3Pmk2)
B-3 KEY CONTACT CLEANING
The B-3/B-3P utilizes multi-contact manuals to produce the drawbar and
key click sounds the same way as the original B-3. There are a total of
1220 gold-plated contacts in both manuals. After some extended period of time,
the contacts will get dirty and will need to be cleaned.
This condition can be recognized by an increase of key-click noise and
intermittent/scratchy sounds from the drawbars. After this condition occurs,
the following key-contact procedure needs to be followed.
PROCEDURE OVERVIEW
Please refer to the picture below.
There are ten bus bars that cover the distance between key 1 and key 61.
One end of the bus bars are clamped in the Bus Bar Shifter Module.
The Hex wrench is inserted into the hex opening in the center of the module.
Rotating the Hex wrench one complete turn will shift the bus bars through
both the right and left limits.
Leaf contact
CLEANING INSRUCTIONS
Lower manual
(see left picture below)
Step 1. Locate the adjustment hole behind the BASS knob as shown below.
Step 2. Insert the hex wrench and rotate slowly until the shifter cam hole is located.
Step 3. Turn the wrench clockwise slowly until turning pressure increases if the wrench
turns easily at first. After pressure increases, turn an additional 15 degrees.
Step 4. If turning pressure is high initially, then only turn the wrench 15 degrees and stop.
Step 5. Remove the wrench and check for key noise. If the noise is gone, the contact has
been cleaned successfully.
Marking
for Lower manual
for Upper manual
Bus bar
15
Bus bar shifter module
Upper manual
°
15°
(see right picture above)
Step 1. Locate the upper manual adjustment hole and insert the hex wrench
until the shifter hole is located.
Hex wrench
Step 2. Follow steps 3 to 5 above.
INSTRUCTION (B-3PmK2) 00457-40104 0810