Manual - Technika Bellissimo

Manual - Technika Bellissimo
Instructions for Use and Installation
Freestanding Cookers:
- B9GEFTSS-3
Contents
For your safety
Safety of children and the infirm . . . . . . . . . . . . . . . . . . . . . . . . 3
Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
During use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Service and spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Use and Care
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Oven & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Instructions for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
How to use your oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Positioning the oven trays & shelves . . . . . . . . . . . . . . . . . . . . 13
Cooking modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Mechanical Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Practical cooking advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning & maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installation
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Instructions for Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Combustible surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Anti-tilting chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Connection to the gas supply . . . . . . . . . . . . . . . . . . . . . . . . . 32
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Replacing the power supply lead. . . . . . . . . . . . . . . . . . . . . . . 33
Before leaving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Gas Conversion
NG - U-LPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
U-LPG - NG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2
For Your Safety
We recommend that you read the instructions in this owner's
manual carefully before use for the best performance and to
extend the life of your appliance. It will provide you with all the
information you need to ensure its safe installation, use and
maintenance. Retain this owner's manual for future reference.
To maintain the efficiency and safety of this appliance, we
recommend that you do the following:
· Always call the Technika service department if there are any
faults with your appliance.
· Always use original spare parts available from Technika.
· This appliance is designed for non-commercial, household use
and it must not be altered in any way.
· This appliance can only be used safely when it is correctly
connected to an efficient earthing system in compliance
with current electrical safety standards.
· If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
Packaging items such as plastic bags, polystyrene, nails, etc. are
potentially dangerous, and therefore appropriate measures must
be taken to prevent children and the disabled from coming into
contact with them.
Safety of children and the infirm
This appliance must only be used by adults. Make sure that
children do not touch the controls or play with the appliance.
The exposed parts of this appliance heat up during cooking and
remain hot for some time even after it is switched off. Keep children
well away until the appliance has cooled down.
Cleaning and maintenance
Keep the appliance thoroughly cleaned. Food residues may cause
fire risks.
3
For Your Safety
During use
· The appliance becomes hot. Care should be taken to avoid
touching heating elements inside the oven.
· WARNING: Accessible parts will become hot when in use.
To avoid burns and scalds, children should be kept away.
· The appliance is not intended for use by young children or
infirm persons without supervision. Young children should
be supervised to ensure that they do not play with the
appliance.
· DO NOT use a steam cleaner to clean the appliance.
· This product is designed to cook foods inside private
homes and for non-commercial purposes. It should not be
used for any other purpose.
· After using the appliance, make sure that all controls are in
'CLOSED' or 'OFF' position.
· DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE
APPLIANCE STORAGE DRAWER OR NEAR THIS
APPLIANCE.
· DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS
APPLIANCE WHILE IT IS IN OPERATION.
· DO NOT STORE OR USE FLAMMABLE LIQUIDS OR ITEMS
IN THE VICINITY OF THIS APPLIANCE.
· WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT
OR IN CARAVANS, IT SHALL NOT BE USED AS A SPACE
HEATER.
· Only use the appliance to cook food and nothing else.
· Disconnect the appliance from the electrical mains if it is
not functioning properly and before cleaning or performing
maintenance.
· Use oven gloves to place cookware in the oven or when
removing it. Always grip the oven door handle in the centre.
· Technika will not accept any liability as a result of any
damage due to incorrect installation or improper use.
4
For Your Safety
Installation
· Installation of the appliance and its connection to the
electrical mains must only be carried out by Authorised
Personnel. Before any service procedure, it is important to
check that the appliance is DISCONNECTED from the
electrical mains.
· DO NOT MODIFY THIS APPLIANCE.
· After removing the appliance from the packaging, make
sure that it is undamaged and that the electrical lead is in
perfect condition. Otherwise, contact your dealer before
operating the appliance.
· Make sure that air is able to circulate freely around the
appliance. Poor ventilation produces a shortage of oxygen.
· Make sure that the appliance is supplied with the type of
gas indicated on the data label and the gas type label next
to the gas connection point.
· Use of a gas cooking appliance produces heat and
moisture in the room in which it is installed. Ensure that the
room is well ventilated by keeping the air intakes open and
in good working order or by installing an extractor hood
with discharge pipe.
· If the appliance is used intensively for a long time the
effectiveness of the ventilation will have to be increased, for
example by opening a window or increasing the power of
any electric extractor fan.
· NOT FOR USE IN MARINE CRAFT, CARAVANS OR MOBILE
HOMES UNLESS EACH BURNER IS FITTED WITH FLAME
SAFEGUARD.
5
For Your Safety
Avoid the following:
· Touching the appliance with wet parts of the body.
· Using the appliance while barefoot.
· Improper or dangerous operation.
· Obstructing the ventilation or heat dissipation slots.
· Allowing power supply cables of other appliances to come into
contact with hot parts of the oven.
· Exposing the appliance to atmospheric agents such as rain, or
direct sunlight.
· Using the oven for storage purposes.
· Using flammable liquids near the appliance.
Authorised personnel must be contracted to...
· Install the appliance according to these installation instructions
and any local requirements.
· Replace the temperature probe if it is damaged. The probe is
part of thermostat. Only use the temperature sensing probe
recommended for this oven.
Technika Service Department must be contacted...
· If in doubt about the operation of the appliance.
· If in doubt about the soundness of the appliance after removing
it from its packaging.
· If the power supply cable has been damaged or needs to be
replaced.
· If the appliance requires a service or you need spare parts.
Service and spare parts
If the appliance fails to operate correctly, never attempt to repair
the appliance yourself. Repairs by unskilled persons may cause
damage and accidents. First refer to the contents of this manual. If
you do not find the necessary information, contact your nearest
Service Center. Servicing work on this appliance must be carried
out by Authorised Personnel. Always request the use of original
spare parts.
For Service & Spare Parts please contact: 1800 333 244
6
Use and Care
Description of the appliance
1. Mechanical Timer
2. Control Knob (Cooktop Burners)
3. Cooking Temperature Selection Knob
4. Cooking Mode Selection Knob
5. Auxiliary burner
6
7
6. Semi-Rapid burner
7. Wok burner
8. Rapid burner
9. Pan supports
6
9
8
5
1
4
2
3
Note: Pan supports may vary on some models.
7
Use and Care
Oven & accessories
The oven is supplied with chrome wire Shelf Supports and a range
of shelf options as shown below. There are four shelf positions on
the oven.
Grill Tray with
removable insert
Oven Shelf
Shelf
Supports
Oven Door
8
Use and Care
Controls
Control Knob
(Cooktop Burners)
Mechanical
Timer
10
20
30
120
40
110
100
50
90
60
80
Cooking Temperature
Selection Knob
70
Cooking Mode
Selection Knob
°C
60
80
MAX
100
220
120
200
140
180
160
9
Use and Care
Instructions for use (cooktop burners)
The symbols on the control knobs mean the following:
No gas flow or 'Off'
Maximum gas flow or 'high' flame and lighting position
Minimum gas flow or 'low' flame
All operating positions must be set between the maximum and
minimum flow settings, and never between the maximum setting
and the closed position.
A - Burner cap
B - Burner Head
C - Burner Bowl
D - Thermocouple (where fitted)
E - Electrode
A
A
A
B
B
E
E
D
D
C
C
Fig. 1
10
Use and Care
To light the cooktop burners
To light the burner, press the control knob fully down and hold the
knob down before rotating anti-clockwise to the High Flame
position. The ignition device is integrated into the control knob and
is automatically activated by pushing down on the control knob.
After lighting the flame, keep the knob pressed for about 10
seconds: this time is necessary to heat up the thermocouple
(Fig.1-D) and activate the safety valve, which would otherwise cut
off the gas flow. This step only applies where flame failure device is
fitted.
In the instance of a power failure, place a lit match near the burner
and proceed as described above. If the flame does not light after
the first attempt, wait 5 minutes for the gas to dissipate before
attempting to re-light the burner.
Once lit, check that the flame is even and turn the control knob to
adjust the flame as required. If the flame is uneven, check that the
'burner head/skirt' and 'burner cap' are correctly positioned. To turn
off the flame, turn the control knob clockwise to the off position
( symbol). Before removing pots or pans from the burners, always
turn off the flame.
For correct use of the cooktop
For lower gas consumption and better efficiency, use only flatbottomed pans of dimensions suitable for the burners, as shown in
the table below. Also, as soon as a liquid comes to the boil take
care to turn the flame down to a level that will just keep it boiling.
Burner
Large(rapid)
Medium(semi-rapid)
Small(Auxiliary)
Triple Flame (Wok)
Minimum diameter
150mm
130mm
90mm
210mm
Maximum diameter
260mm
180mm
160mm
270mm
During cooking processes involving fats or oils, watch your foods
carefully because these substances may catch fire if overheated.
11
Use and Care
How to use your oven
This multi-function oven combines the advantages of traditional
convection ovens with modern fan assisted ovens in a single
appliance. It is an extremely versatile appliance that allows you to
choose easily and safely between different cooking modes. The
various cooking modes are selected by means of a cooking mode
selection knob, located on the control panel.
To operate the oven:
· Ensure that manual mode is selected (page 16)
· Turn the cooking mode selection knob to the desired cooking
mode (explanation of cooking modes is on pages 14 to 15)
· Turn the cooking temperature selection knob to the desired
temperature (cooking guide is on pages 23 to 24) or to ‘MAX’ if
Grilling.
The first time you use your appliance, we recommend that you set
the thermostat to the highest setting, set the cooking mode
selection knob to a cooking mode and leave the oven on for about
half an hour with nothing in it and the oven door closed. Then,
open the oven door and allow the oven to cool. Any odour that may
be detected during this initial use is due to the evaporation of
substances used to protect the oven during storage.
Note: Place tray on the bottom shelf position of the oven to prevent
any spillages from dripping onto the bottom of the oven. Never
place anything (including foil and oven trays) on the bottom of
the oven when it is in operation because this could damage
the enamel. Only place your cookware (dishes, trays, aluminum
foil, etc.) on the Oven Shelves provided with the appliance.
If supplied, use the
chrome wire handle
shown left when
removing the trays
from the oven.
12
Use and Care
Positioning the oven trays & shelves
The Grill Tray or Oven Shelf can be located in any of the five height
positions of the oven.
Refer to the ‘Cooking Mode Table’ for the recommended shelf
position. When fitting the trays or shelves, ensure they are fitted
between the two wires that are closest together as shown below.
Oven Shelves have a stop so that they are not fully withdrawn by
accident. To fully remove the Oven Shelves, lift the front of the shelf
slightly and withdraw fully from the oven. Note that the Grill Tray
does not have a stop position and can be fully withdrawn without
interruption, so be careful not to accidentally fully withdraw the
trays.
Fit Trays and
Shelves
between bars
as shown right
To remove the Oven Shelf
Support, push down on the
wire below the locking pin,
pull away from the oven wall
until you can release the
bottom of the support from
the holes in the oven wall.
Replace in reverse
procedure.
Oven Shelf fitted to chrome
wire Shelf Support
13
Use and Care
COOKING MODES
Grill mode
Select ‘Grill’ mode with cooking mode selection knob and turn
cooking temperature selection knob to ‘Max’. When set to Grill
mode, the top inner element operates. The extremely high and
direct temperature of the grill makes it possible to brown the
surface of meats and roasts while locking the juices in to keep
them tender. Grill mode can also be used for dishes that require a
high temperature on the surface such as beef steaks, veal, rib
steak, filets, hamburgers, etc.
Grill food with the oven door closed (when not using fan).
Fan assisted grill mode
Select ‘Fan Assisted Grill’ mode with cooking mode selection knob
and turn cooking temperature selection knob to the desired
temperature setting. When set to Fan Assisted Grill mode, the top
inner element and the fan operate. This mode increases the
circulation of air throughout the oven, which helps prevent food
from burning on the surface, allowing the heat to penetrate right
into the food. Particularly suitable for kebabs made with meats and
vegetables, sausages, ribs, lamb chops, chicken, quail, pork
chops, fish steaks, stuffed cuttlefish etc.
In Fan Assisted Grill mode, grill with the oven door closed.
Baking mode
When set to Baking mode, the fan element and the fan operate
providing a delicate heat distributed uniformly throughout the oven.
This mode is ideal for baking and cooking delicate foods on
multiple shelves, especially cakes that need to rise such as cream
puffs and for certain tartlets, sweet or savoury biscuits, savoury
puffs, swiss rolls and small portions of vegetables, etc.
14
Use and Care
Defrost mode
When set to ‘Defrost’ mode, the fan located at the back of the oven
circulates room temperature air around the food. This is
recommended for the defrosting of all types of food, but in
particular for delicate types of food which do not require heat, for
example: ice cream cakes, cream or custard desserts, fruit cakes,
etc. By using ‘Defrost’ mode, the defrosting time is approximately
halved. In the case of meat, fish and bread, it is possible to
accelerate the process by selecting ‘Multi Cooking mode’ and
setting the temperature between 80°C to100°C.
15
Use and Care
Mechanical Timer
The Mechanical Timer automatically controls when the oven shuts
off. It cannot automatically switch the oven on, only off. Turn the
timer knob to between 10 minutes and 120 minutes.
At the end of the selected time period, the timer will sound and
automatically turn off the oven.
To operate the oven manually, set the timer to
The oven light
Set cooking mode selection knob to
symbol to switch on the
oven light/s. The oven light/s stay on when the oven is operating.
Cooling ventilation
In order to cool down the exterior of the appliance, this model is
equipped with a cooling fan, which switches on automatically.
When the cooling fan is on, you will notice a flow of air exiting
between the oven door and the control panel.
Note: When cooking is finished, the cooling fan continues to
operate until the oven cools down and then switches off
automatically.
16
Use and Care
PRACTICAL COOKING ADVICE
The oven offers a wide range of settings which allow you to cook
any type of food in the best possible way. With time you will learn to
make the best use of this versatile cooking appliance and the
following directions are only a guideline which may be varied
according to your own personal experience.
Preheating
If the oven needs to be preheated, the ‘Baking’ mode
should be
selected. This is the most efficient mode, which will reach the
desired temperature as quickly as possible using the least amount
of energy.
Once the food has been placed in the oven, the desired cooking
mode should then be selected.
Multi shelf cooking
If you want to cook food on several shelves, select the ‘Baking’
mode
as this is the only cooking mode that allows you to do so.
When cooking delicate foods on more than one shelf, use the
‘Baking’ mode. This mode allows you to cook on 3 shelves at the
same time. Refer to the ‘Cooking Guide’ table.
17
Use and Care
Using the grill
This multi-function oven has 2 different grilling modes.
Use the ‘Grill’ mode
with the oven door closed, place the food
on the centre of the grill pan, insert and fit the grill pan on either
the 3rd or 4th shelf from the bottom. Note: only the central part of
the top heating element operates for grilling.
When using ‘Grill’ mode, we recommend you set the thermostat to
the highest setting. However, this does not mean you cannot use
lower temperatures, simply adjust the thermostat knob to the
desired temperature.
Use ‘Fan assisted grill’ mode
with the oven door closed. This
mode is very useful for grilling foods rapidly, as the distribution of
heat by the fan makes it possible not only to brown the surface, but
also to cook the bottom of the food. It can also be used for
browning foods at the end of the cooking process, such as adding
that gratin finish to pasta bakes for example.
When using ‘Fan assisted grill’ mode, place the food on the 2nd or
3rd oven shelf from the bottom, then place a dripping-pan on the
1st rack from the bottom to prevent fat and grease from dripping
onto the oven floor. We recommend you set the thermostat to
200°C, as it is the most efficient temperature for ‘Fan assisted grill’
mode. However, this does not mean you cannot use lower
temperatures, simply adjust the thermostat knob to the desired
temperature.
Important: for best results and to save energy, always use the ‘Fan
assisted grill’ with the oven door closed.
18
Use and Care
Baking cakes
When baking cakes ,always place them in a preheated oven. Make
sure you wait until the oven has been preheated thoroughly (the
indicator light will turn off). To prevent heat loss and the cake from
dropping, do not open the oven door during baking.
In general...
... if pastry is too dry
Increase the temperature by 10°C and reduce the cooking time.
... if pastry has dropped
Use less liquid or lower the temperature by 10°C.
... if pastry is too dark on top
Place it on a lower shelf, lower the temperature, and increase the
cooking time.
... if cooked well on the inside but sticky on the outside
Use less liquid, lower the temperature, and increase the cooking
time.
... if the pastry sticks to the pan
Grease the pan well and sprinkle it with a dusting of flour or use
greaseproof paper.
... if I used multi shelf cooking and one shelf is more cooked
Use a lower temperature setting next time. It is not necessary to
remove the food from all the racks at the same time.
19
Use and Care
Cooking pizza
For best results when cooking pizza:
· Preheat the oven for at least 10 minutes.
· Use a light aluminum pizza pan, placing it on the shelf supplied
with the oven. Don’t use the dripping pan since this will extend
the cooking time, making it difficult to get a crispy crust.
· Do not open the oven door frequently while the pizza is cooking;
· If the pizza has a lot of toppings (three or four), we recommend
you add the mozzarella cheese on top halfway through the
cooking process.
· For best results, only use one shelf at a time, but if you want to
cook on two shelves, use the 2nd and 4th racks from the bottom
with a temperature of 220°C and swap them halfway through
cooking.
Cooking fish and meat
When cooking white meat, fowl and fish, use a temperature setting
from 180°C to 200°C.
For red meat that you want well done on the outside while tender
and juicy in the inside, it is best to start with a high temperature
setting (200°C-220°C) for a short time, then turn the oven down
afterwards.
In general, the larger the roast, the lower the temperature setting.
Place the meat on the centre of the shelf and place the dripping
pan beneath it to catch the fat.
Make sure that the shelf is inserted so that it is in the centre of the
oven. If you would like to increase the amount of heat from below,
use a lower shelf height. For savoury roasts (especially duck and
wild game), dress the meat with lard or bacon on the top.
20
Use and Care
Cooking guide
Note: Cooking times are approximate and may vary according to
personal taste. When cooking using the grill or fan assisted grill,
the dripping pan must always be placed on the 1st oven shelf from
the bottom.
21
Use and Care
Cooktop cleaning and maintenance
Before cleaning, make sure all burners are 'off' and allow the
appliance to cool down.
The enamelled or stainless steel parts should be washed with
lukewarm water without using any abrasive powders or corrosive
substances. If any stainless steel has difficult to remove stains, use
cleaners specifically recommended to clean stainless steel. After
cleaning any surface, it is advisable to rinse thoroughly and dry.
Wash the burner caps and head/skirts often with hot water and
detergent, taking care to remove all deposits. Ensure the burner
ports in the head/skirts are clear and are not blocked by water or
detergent. The hob pan stands can also be washed in a
dishwasher. For stubborn dirt, use ordinary non-abrasive
detergents or specific commercial products. We strongly advise not
to use scouring pads, steel wool or acids for cleaning. Do not
steam clean this appliance.
Ignition plug
Automatic burner ignition is provided by a ceramic 'plug' and a
metal electrode (E in fig.1). Periodically clean these parts of the
hob thoroughly. In addition, to avoid ignition difficulties, check that
the cavities in the burner are not obstructed. To remove deposits
from the burner cavities, remove the burner caps (see images
right). After cleaning, put the burner heads and caps back together
and return them correctly to their position. After washing, replace
the pan supports, checking that they are correctly positioned.
22
Use and Care
Oven cleaning and maintenance
Before cleaning your oven or performing maintenance, make sure
that the cooking mode selection knob and the cooking temperature
selection knob is set to ‘OFF’. To extend the life of your oven, it
must be cleaned frequently.
The inside of the oven should preferably be cleaned immediately
after use, when it is still warm (but not hot), with warm water and
soap. The soap should be rinsed away and the interior dried
thoroughly. Avoid using abrasive detergents, scourers acidic
cleaners such as lime scale remover, etc. as these could damage
the enamel. If stains are particularly tough to remove, use cleaners
specifically recommended to clean ovens and follow the
instructions provided with the cleaner. Never use a steam cleaner
for cleaning inside the oven.
If you operate your oven for an extended period of time, or if you
are cooking dishes that contain a lot of water, condensation may
form on the oven door. Dry it using a soft cloth and try reducing the
cooking temperature.
There is a rubber seal surrounding the oven opening which is
necessary to ensure the correct operation of the oven. Check the
condition of this seal on a regular basis. If necessary, clean it but
avoid using abrasive products or objects to do so. Should it
become damaged, please contact Technika Service Department.
We recommend you avoid using the oven until it has been
repaired.
Never place anything (including foil and oven trays) on the
bottom of the oven when it is in operation because this could
damage the enamel.
Clean the glass door using non-abrasive products or sponges and
dry it with a soft cloth.
Do not use abrasive cleaners or sharp metal scrapers to clean the
oven door glass since they can scratch the surface, which may
result in shattering the glass.
23
Use and Care
How to remove the oven door
You can remove the oven door for better access to the oven when
cleaning. There are 2 styles of oven door so you should first
identify which style you have. Proceed as follows for each style:
Oven door style 1:
· Open the door fully.
· Lift up and turn the small hooks located on the two hinges.
· Grip the door on the two external sides, shut it slowly but not
completely.
· Pull the door up towards you, lifting it out of the oven frame.
· To replace the door, use the reverse procedure.
1
2
3
Oven door style 2:
· Open the door fully.
· Lift up and turn the small hooks situated on the two hinges.
· Grip the door on the two external sides and close it
approximately half way. Unlock the door by pressing on the
clamps ‘A’.
· Pull the door up towards you, lifting it out of the oven frame.
· To replace the door, use the reverse procedure.
1
2
3
A
F
24
Use and Care
Replacing the oven lamps
WARNING: Ensure that the appliance is switched off before
replacing the lamp to avoid the possibility of electric shock.
Remove the glass cover of the lamp-holder as shown below.
Remove the lamp and replace with a lamp resistant to high
temperatures (300°C) with the following characteristics:
- Voltage: 220-240V
- Wattage: 25W
- Type: E 14
Replacement lamps are available from Technika. Replace the glass
cover and reconnect the oven to the mains power supply.
25
Use and Care
Routine maintenance
Have the condition and efficiency of the gas pipe and the pressure
regulator (if installed) checked periodically. If anomalies are found,
do not repair components but have the faulty component replaced.
To ensure good performance and safety, the gas regulator taps
must be greased periodically.
Periodic lubrication of the taps and any other appliance service
must only be carried out by Authorised Personnel.
Abnormal operation
Any of the following are considered to be abnormal operation and
may require servicing:
· Yellow tipping of the burner flame.
· Sooting up of cooking utensils.
· Burners not igniting properly.
· Burners failing to remain alight.
· Burners extinguished by cupboard doors.
· Gas valves, which are difficult to turn.
In case the appliance fails to operate correctly, contact Technika.
Service and parts
Before leaving the factory, this appliance was tested and adjusted
by specialist skilled staff to give the best operating results. Any
subsequent necessary repairs or adjustments must be carried out
with the greatest care and attention by authorised personnel. For
this reason, we strongly advise you contact the Technika Service
Center, specifying the nature of the problem, the model of the
equipment and the serial number. This data is provided on the data
label adhered to the base of the appliance and on the duplicate
data label. Always use original Techinka spare parts.
Warranty
Your new appliance is covered by a warranty. The details of your
warranty conditions are on your Warranty Card supplied with the
appliance. Keep the physical receipt which documents your
purchase of the appliance and purchase date as you will need to
show this for any Warranty repairs. Warranty cannot be claimed
without proof of purchase.
26
Use and Care
Disposal
By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate
waste handling of this product.
The symbol on the product indicates that this product may not be
treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment.
Disposal must be carried out in accordance with local
environmental regulations for waste disposal.
For more detailed information about treatment, recovery and
recycling of this product, please contact your local city
council office.
27
Installation
Technical data
· Gas intake connection
1/2" BSP
· Electricity supply
240V AC (50Hz)
Natural Gas
1.0 kPa
Burner Type
Universal LPG
2.75 kPa
Injector Nominal Gas Injector Nominal Gas
(mm) Consumption (mm) Consumption
Auxiliary
0.88
3.7 MJ/h
0.53
3.4 MJ/h
Semi Rapid
1.16
6.8 MJ/h
0.68
6.0 MJ/h
Rapid
1.50
11.0 MJ/h
0.88
10.2 MJ/h
Wok
1.75
14.5 MJ/h
1.00
13.1 MJ/h
Inner dimensions of the oven:
Width: 69 cm
Depth: 43 cm
Height: 37 cm
Inner Volume of the oven: 105 litres.
Voltage and Frequency of Power Supply:
240V ~ 50Hz
Electrical Features:
Oven light: 2×25W
Upper heating element: 2200W
Bottom heating element: 1800W
Grill heating element: 2900W
Circular heating element: 1×1800W
Motor ventilator: 2×30W
Cooling fan: 20W
28
Installation
Instructions for installation
This appliance shall be installed only by authorised persons and in
accordance with the manufacturer's installation instructions, local
gas fitting regulations, municipal building codes, electrical wiring
regulations, AS 5601-2004 - Gas Installations and any other
statutory regulations.
IMPORTANT: Installation, assembly and gas/electrical
connections must be carried out by authorised personnel.
Data Label - The Data Label is located on the rear of the
appliance. A duplicate Data Label is supplied to adhere in an
accessible area next to the appliance. This appliance is suitable for
Natural Gas and Universal LPG; ensure that the available gas
supply matches the Data Label and the gas type label.
Ventilation - Ventilation must be in accordance with AS5601-2004 Gas Installations. In general, the appliance should have adequate
ventilation for complete combustion of gas, proper flueing and to
maintain temperature of immediate surroundings within safe limits.
Before any procedure, it is important to check that the appliance is
DISCONNECTED from the electrical mains. The Manufacturer
declines all responsibility for any damage deriving from
installations in breach of the regulations in force or from failure to
comply with these installation instructions.
29
Installation
Dimensions
The Gas Inlet
Connection is male
½" BSP and is
located 55mm from
the right and 560mm
from the floor.
Combustible Surfaces
This appliance shall be installed in accordance with
AS 5601-2004 - Gas Installations Figure 5.1: Required Clearances
around Domestic Cooking Appliances.
Any adjoining wall surface situated within 200mm from the edge of
any burner must be a suitable non-combustible material for a
height of 150mm for the entire length of the appliance. Any
combustible construction above the appliance must be at least
600mm above the top of the burner and no construction shall be
within 450mm above the top of the burner. Zero clearance is
permitted on the side and rear adjoining surfaces below the
maintop.
If the bench-top is situated within 200mm from the edge of any
burner, it should be 10mm or more below the hob as shown above.
Install Range Hoods and Exhaust Fans in accordance with the
manufacturer’s instructions, no closer than 600mm above the
maintop for Range Hoods and 750mm for Exhaust Fans.
30
Installation
Freestanding or plinth installation
The appliance can be installed as a freestanding cooker or it can
be installed on a plinth. If installing the appliance as a freestanding
cooker, screw the height adjustable telescopic legs supplied to the
base of the appliance. If installing the appliance on a plinth, screw
the levelling feet supplied to the base of the appliance.
Anti-tilting chain/hose restraining chain
WARNING: Ensure the chains are correctly anchored to
prevent the appliance from tilting forward and to prevent
strain on the hose when the cooker is pulled forward.
MAKE SURE THE CHAINS ARE TAUGHT WHEN ANCHORED
TO PREVENT THE APPLIANCE TILTING.
The cooker is supplied with two chains which are connected to the
rear left and right of the appliance. The chains should be
connected to the wall directly behind the chains as low as possible
to prevent the appliance from tilting forward. If the appliance is
installed between two cupboards, holes should be drilled on each
side of the cupboards and the chains should be anchored within
each side of the cupboards.
The chains also prevent strain on the hose when the cooker is
pulled forward.
Ensure the chain connections are strong enough to support the
weight of the appliance. Also ensure the chains are taught to
prevent the appliance from tilting.
Once the chains are installed, check that they prevent the
appliance from tilting forward and that there is no strain on the
hose when the cooker is pulled as far forward as the chains allow.
31
Installation
Connection to the gas supply
For ease of service, the cooker should be connected with a
Flexible Hose, which complies with AS/NZS 1869 (AGA Approved),
10mm ID, class B or D, between 1 - 1.2m long and in accordance
with AS5601 for a high level connection.
WARNING: Ensure that the hose is not subjected to abrasion,
kinking or permanent deformation and should be able to be
inspected along its entire length. Unions compatible with the hose
fittings must be used and connections tested for gas leaks. The
fixed consumer piping outlet should be at approximately the same
height as the cooker connection point, pointing downwards and
approximately 200mm - 300mm in from the left hand side of the
cooker. The hose should be clear of the floor when the cooker is in
the installed position. The hose restraint chain supplied should be
anchored to the wall so that the chain prevents strain on the hose
connections when he cooker is pulled forward.
The supply connection point must be accessible with the appliance
installed. Fit the supplied elbow and gasket as shown in the
illustration below. The gas inlet connection has a 1/2" BSP male
thread. When making the connection, take care not to apply
excessive stress by counterbalancing tightening force. Ensure that
the available gas supply is the same as the gas type label affixed
near the gas connection point. If not, contact Technika for a Gas
Conversion Kit. The gas supply pressure must be adjusted in
accordance with the data label for the gas type. Adjust the test
point pressure with the largest burner operating at maximum.
A
B
C
A - Manifold Nut
B - Gasket
C - Elbow
32
Installation
Electrical connection
Connection to the electricity supply must be made by an
authorised person is accordance with the Wiring Rules
AS/NZS3000.
If connecting the cable directly to the mains, install a suitable
isolating switch with a minimum contact opening of 3mm between
the appliance and the mains. The isolating switch should be sized
according to the load on the data label and should comply with
current regulations (the earth wire should not be interrupted by the
circuit breaker).
The supply cable should be positioned so that it does not reach a
temperature of more than 75℃.
If a plug is not fitted to the cable, and you would like to connect the
appliance to a socket outlet, fit a plug that is appropriately rated for
the load indicated on the data plate to the cable supplied with the
appliance. The plug must be compatible with the socket outlet fitted
to the final sub-circuit in the fixed wiring that is intended to supply
this appliance.
Replacing the power supply lead
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in
order to avoid hazard.
Before leaving
When the installation is complete, always check for gas leaks using
a soapy solution. Never use a flame to make this check.
Ignite all burners on high flame to ensure correct operation of gas
valves, burners and ignition. Turn gas taps to low flame position
and observe each burner to ensure they ignite completely at all
ports and that the flame is stable. Conduct these checks for each
burner individually and concurrently.
When satisfied with the hotplate, please instruct the user on the
correct method of operation. In case the appliance fails to operate
correctly after all checks have been carried out, please call the
Technika Service Centre.
33
Gas Conversion (NG to U-LPG)
Parts needed...
- Test Point Assembly
- Auxiliary Jet Ø0.53mm
- Rapid Jet Ø0.88mm
- ULPG Gas Type label
- Semi-Rapid Jet Ø0.68mm
- Wok Jet Ø1.00mm
Converting to a different gas type
When converting from Natural Gas to Universal LPG ensure that the
NG regulator is removed and replaced with the Test Point Assembly
supplied in the conversion kit. An AGA Approved gas regulator suitable
for a supply pressure of 2.75kPa should be part of the gas tank supply
and the test point pressure must be adjusted to 2.75kPa.
Changing the jets
1. Remove pan supports, burner heads and caps.
2. Use a size 7 socket wrench to unscrew and
remove the jets, replacing them with those
supplied in the conversion kit. Ensure you use
the correct jet for the corresponding burner.
3. Reassemble the burner heads, caps and pan
supports.
4. Fit the Gas type label supplied in the conversion
kit next to the gas connection point and remove
the existing label.
Setting the minimum level
1. Light one of the burners and turn the tap to
minimum flame.
2. Remove the corresponding control knob.
3. Use a thin blade screwdriver to turn the by-pass
screw located above left of the gas valve shaft
as shown right. Turn the by-pass screw fully
clockwise. The result should be a small, stable
flame which is uniform around the entire burner
ring. If not, turn the by-pass screw anti-clockwise
until satisfied with the flame.
4. Check that the burner does not go out when the
tap is turned quickly from the maximum to the
minimum position.
5. Repeat for each burner.
34
Gas Conversion (U-LPG to NG)
Parts needed...
- NG Regulator
- Auxiliary Jet Ø0.88mm
- Rapid Jet Ø1.50mm
-NG Gas Type label
- Semi-Rapid Jet Ø1.16mm
- Wok Jet Ø1.75mm
Converting to a different gas type
When converting from Universal LPG to Natural Gas ensure that the
ULPG test point is removed and replaced with the AGA Approved NG
Regulator supplied in the conversion kit. The test point pressure must
be adjusted to 1.00kPa with the largest burner operating on maximum
flame.
Changing the jets
1. Remove pan supports, burner heads and caps.
2. Use a size 7 socket wrench to unscrew and
remove the jets, replacing them with those
supplied in the conversion kit. Ensure you use the
correct jet for the corresponding burner.
3. Reassemble the burner heads, caps and pan
supports.
4. Fit the Gas type label supplied in the conversion
kit next to the gas connection point and remove
the existing label.
Setting the minimum level
1. Light one of the burners and turn the tap to
minimum flame.
2. Remove the corresponding control knob.
3. Use a thin blade screwdriver to turn the by-pass
screw located above left of the gas valve shaft
as shown right. Turn the by-pass screw fully
clockwise then turn it anti-clockwise 1 turn for
the Wok, 3/4 turn for the Rapid, ½ turn for the
Semi-Rapid and 3/8 turn for the Auxiliary. The
result should be a small, stable flame which is
uniform around the entire burner ring. If not, turn
the by-pass screw anti-clockwise until
satisfied with the flame.
4. Check that the burner does not go out when the
tap is turned quickly from the maximum to the
minimum position.
5. Repeat for each burner.
35
READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USINGTHE APPLIANCE.
The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or
improper use of the appliance.
The manufacturer is not responsible for any inaccuracies, due to printing or transcription errors, contained in this
handout. In addition, the appearance of the figures reported is also purely indicative.
The manufacturer reserves the right to make changes to its products when considered necessary and useful, without
affecting the essential safety and operating characteristics.
Technika constantly seeks ways to improve the specifications and designs of their products.
Whilst every effort is made to produce up to date literature, this document should not be regarded as an infallible
guide.
Actual product only should be used to derive cut out sizes.
All Technika Appliances must be installed by a qualified person/s with adherence to the relevant electrical, plumbing
and AGA codes, with compliance being issued as required by state or national legislation.
Additionally all Technika Upright cookers must have chains installed correctly in adherence to the relevant AGA, and
plumbing codes by the Licenced installer.
For maximum effectiveness and efficiency all rangehoods should be installed with the use of ductwork, by a licenced
installer with adherence to the relevant state and national building codes and regulations.
All Technika appliances are for Domestic use only, and must be installed by a licence installer into Domestic
Applications only, without exception and to the required Authorities guidelines. Any installation outside of this will
VOID warranty. Alfresco areas are not a Domestic application.
Beffis::Wl2o
™
BYTECHNIKA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement